flex_gs_2012.1.2

7/27/2019 flex_gs_2012.1.2

1/34

1

Getting Started Using Adams/Flex Adams/Flex

Building and Simulating a Flexible Model

Exchanging a Rigid Body with a Flexible Body
http://2_tutor.pdf/http://3_substitute.pdf/http://3_substitute.pdf/http://2_tutor.pdf/

7/27/2019 flex_gs_2012.1.2

2/34

Getting Started Using Adams/Flex2

Adams/Flex

7/27/2019 flex_gs_2012.1.2

3/34

3Adams/FlexWelcome to Adams/Flex

Welcome to Adams/FlexAdams/Flex is an add-on module to Adams products that lets you add flexible bodies to your models to

achieve more realistic simulation results.

If youve never used Adams/Flex before, this guide is a good place to start learning about Adams/Flex.

As you work through the two tutorials that we have provided, you will learn most of the basic concepts

and tasks that you can perform using Adams/Flex.

Before doing these tutorials you should be familiar with the basic features of the Adams/View interface.

For information about the Adams/View interface, see the guide, Getting Started Using Adams/View.

7/27/2019 flex_gs_2012.1.2

4/34

Getting Started Using Adams/FlexAbout the Tutorials

4

About the TutorialsThe two tutorials in this guide give you an introduction to using Adams/Flex:

Building and Simulating a Flexible Model - The first tutorial teaches you how to integrate

flexible bodies into Adams/View and attach rigid bodies to them. The tutorial also introduces

you to Adams/Flex basics, such as the options that are available for setting up the modal content

of flexible bodies before a simulation.

Exchanging a Rigid Body with a Flexible Body - The second tutorial teaches you how to bring

a flexible body into an existing model and replace a rigid body with the flexible body. It lets you

see how easy it is to integrate the flexible body into an existing rigid model so you can gradually

add complexity and realism to your model.

Note that there are additional tutorials in the guide, Using Adams/Flex, that explain many of the advanced

features of Adams/Flex. They are presented in the chapters in which the advanced features are explained.

7/27/2019 flex_gs_2012.1.2

5/34

1Build ing and Simulating a Flexible Model

Building and Simulating a Flexible Model

7/27/2019 flex_gs_2012.1.2

6/34

Getting Started Using Adams/FlexOverview

2

OverviewThis tutorial explains how to create a flexible model of a cantilever link. It contains the sections:

What This Tutorial Does

What Youll Create and Simulate

Starting Adams/View and Creating a Database

Building the Model

Simulating the Flexible Model

Investigating Modes

Modifying the Modal Content

Viewing Numeric Results

7/27/2019 flex_gs_2012.1.2

7/34

3Build ing and Simulating a Flexible ModelWhat This Tutorial Does

What This Tutorial DoesThis tutorial will help you learn how to investigate flexible bodies using Adams/Flex. It teaches you how

to integrate a modal neutral file (MNF) into an existing modeling database to create a flexible body in

Adams/View. It also explains how to build rigid bodies that attach to the flexible body and how to change

the flexible bodys visual representation. Finally, it explains how to change the properties of the flexible

body by disabling modes and how to examine the effect of these changes on simulation results.

7/27/2019 flex_gs_2012.1.2

8/34

Getting Started Using Adams/FlexWhat Youll Create and Simulate

4

What You ll Create and SimulateIn this tutorial, youll create a model of a cantilever link shown below. The cantilever link is made up of

a flexible link, which you integrate into Adams/View using an MNF and a rigid body sphere. You fix one

end of the link to the sphere and the other end of the link to ground. Youll use a fixed joint to make the

attachments. A fixed joint locks two parts together so that they cannot move with respect to each other.

Youll then simulate the model to see the cantilever link oscillate from the force of gravity.

Figure 1 Cantilever Link Model

7/27/2019 flex_gs_2012.1.2

9/34

5Build ing and Simulating a Flexible ModelStarting Adams/View and Creating a Database

Starting Adams/View and Creating a DatabaseYoull start the tutorial by running Adams/View and creating a modeling database that will contain a new

model called dumbbell. Youll also set the gravity and units for the model.

To start Adams and create your database:

1. Copy the file /install_dir/flex/examples/mnf/link.mnf to your working directory. install_diris the

directory where the Adams software is installed. If you cannot locate this directory, please see

your system administrator.

2. Do either of the following depending on the platform on which you are running Adams/View:

In UNIX, type the command to start the Adams Toolbar at the command prompt, and then

press Enter. Click the Adams/View tool .

In Windows, from the Start menu, point to Programs, point to MSC.Software, point to

Adams 2012, point to Aview, and then select Adams - View.

The Adams/View main window appears.

3. In the Welcome dialog box, select Create a new model, and then assign the new model the name

dumbbell.4. Set Gravity to Earth Normal (- Global Y).

5. Set Units to MKS.

6. Select OK.

7/27/2019 flex_gs_2012.1.2

10/34

7/27/2019 flex_gs_2012.1.2

11/34

7Build ing and Simulating a Flexible ModelBuilding the Model

Figure 2 Adams/View Screen After Importing the MNF

Adding a Fixed Joint

Now youll fix one end of the flexible link to ground using a fixed joint.

To add a fixed join t:1. From the Joint tool stack of the Main toolbox, select the Fixed Joint tool .

2. In the construction container of the Main toolbox, select the construction method1 Location.

3. Place the cursor at the left end of the link. Node numbers flash on the screen as you move the

cursor. Select node 1000 for the location of the fixed joint by clicking the left mouse button when

the cursor is over node 1000. Figure 3 shows the location for the fixed joint. Node 1000 is at

(0,0,0).

4. If you have trouble selecting the node, try zooming in on the model by pressing either the letter

w, to draw a zoom window, or the letterz, to dynamically zoom the window. The window must

be active.

G tti St t d U i Ad /Fl8

7/27/2019 flex_gs_2012.1.2

12/34

Getting Started Using Adams/FlexBuilding the Model

8

Figure 3 Location to Place Fixed Joint

Creating and Moving a Sphere

Now that youve fixed the link to ground, youll create a sphere that attaches to the right end of the link.

Youll also move the sphere so its center goes through the center line of the link.

To create and move a sphere:1. From the Geometric Modeling tool stack of the Main toolbox, select the Sphere tool .

2. Click the left mouse button anywhere in the screen and drag the cursor until you have a sphere

approximately 0.3 meters in diameter. (Remember that the length of the link is 0.5 meters.)

3. From the Move tool stack of the Main toolbox, select the Point-to-Pointtool .

4. Following the instructions in the status bar, select the sphere as the object to move. Click near the

left edge of the sphere to indicate the point to move from, and then, click on node 1001 at the right

end of the link to indicate the point to move to. Press the Ctrl key to use grid points or zoom inon the model to gain greater accuracy.

FLEX_BODY_1.N1000


7/27/2019 flex_gs_2012.1.2

13/34

9Build ing and Simulating a Flexible ModelBuilding the Model

Figure 4 shows the objects you should select to move the sphere. In the figure, the sphere is

located on the left side of the link. The sphere you created could be anywhere in the screen but

you still need to select the point on the sphere farthest to the left as the point to move from as

illustrated in the figure. The alignment of the sphere with node 1001 does not need to be accurate.

Adams/View moves the sphere so its center goes through the center line of the link.

Figure 4 Objects to Select to Move Sphere

Adding a Second Fixed Joint

Your final step in creating the cantilever link is to fix the sphere you created to the link using a fixed joint.

To add a joint :

1. From the Joint tool stack of the Main toolbox, select the Fixed Joint tool .

2. In the construction container of the Main toolbox, select the construction method2 Bod - 1 Loc.

3. Select the link, the sphere, and the end of the link where it coincides with the sphere(FLEX_BODY_1.N1001).

Adams/View attaches a fixed joint as shown in the figure below.

Point to move from

Point to move to


7/27/2019 flex_gs_2012.1.2

14/34

Getting Started Using Adams/FlexBuilding the Model

10

Youll now simulate the model to see how it moves.

Figure 5 Sphere Connected to Flexible Link


7/27/2019 flex_gs_2012.1.2

15/34

11Build ing and Simulating a Flexible ModelSimulating the Flexible Model

Simulating the Flexible ModelIn this section, youll run a simulation of the cantilever link you created to see how it moves. Youll run

a one-second simulation that outputs data 100 times.

To simulate the flexible body:

1. From the Main toolbox, select the Simulate tool .

2. In the Simulation container in the Main toolbox, enter the following:

In the End Time text box, enter1 second.

In the Steps text box, enter100.3. Select the Simulation Start tool . You see the cantilever link oscillating because of the force

of gravity as shown in the next figure.

Figure 6 Oscillating Cantilever Link


7/27/2019 flex_gs_2012.1.2

16/34

g gInvestigating Modes

Investigating ModesAdams/Flex lets you set options to help you see the deformation of the flexible body during an animation.

In the next sections, youll change the contour color, specify a node relative to which the flexible body

appears to deform, and scale the deformed mode display. There are many other options available for

enhancing the visual representation of the flexible body.

Displaying the Flexible Body Modify Dialog Box

Adding Color Contours

Setting the Datum Node

Changing the Deformation Scale


All the changes you make to a flexible body, you make through the Flexible Body Modify dialog box.

You display the dialog box just as you would any modify dialog box in Adams/View.

To display the Flexible Body Modify dialog box:

1. In the Simulation container of the Main toolbox, select the Reset tool to return to modeling

mode.

2. Double-click the flexible body to display the Flexible Body Modify dialog box shown in the next

figure.


7/27/2019 flex_gs_2012.1.2

17/34

Investigating Modes

The figure indicates the three controls that you use to change the deformation display of a flexible

body.

Adding Color Contours

In this section, youll set Adams/Flex so that it changes the color of the flexible link as the link deforms

to indicate the magnitude of the deformation.

Specifies a node

Turns on contours

Exaggerates theamount of deformation

relative to which thebody appears todeform

Getting Started Using Adams/FlexI ti ti M d

14

7/27/2019 flex_gs_2012.1.2

18/34

Investigating Modes

By default, Adams/Flex considers the deformation to be relative to the origin of the flexible body (its

local body reference frame (LBRF) or coordinate system). Youll notice that at the start of the animation,

the flexible link is completely blue. As the animation runs, it changes to red to indicate where and when

the maximum deformation occurred.

To change the color contour:

1. From the Flexible Body Modify dialog box, set Plot Type to Contour.

2. From the Main toolbox, select the Animation tool .

3. In the Animation container on the Main toolbox, be sure that Contour Plots is selected.

4. From the Animation container, select the Play tool .There is a short hesitation before the animation starts because Adams/View computes and scales

colors based on the deformation that occurred during the simulation.

Setting the Datum Node

Now youll set the datum node that you want deformation color changes to appear to be relative to. As

explained in the previous section, Adams/Flex considers the deformation to be relative to the origin ofthe flexible body (its LBRF or coordinate system) by default. In this section, youll change it to node

1000, which lets you see deformations relative to the nodes at the end of the link that is fixed to ground.

To change the datum node:

1. In the Animation container on the Main toolbox, select the Rewind tool to reset the animation

back to its first frame.

2. In the Flexible Body Modify dialog box, clear the selection ofLBRF.

3. In the Datum Node text box, enter1000.

4. Select Apply or press Enter.

5. In the Animation container on the Main toolbox, select the Play tool and observe the color

scheme, which is more realistic. Youll notice that there is a slightly longer hesitation before the

animation begins because now there is the added cost of scaling deformation color relative to a

datum node.

6. Select the Stop tool .

Note: If you receive the warning shown below you incorrectly selected the Animate tool on the

Flexible Body Modify dialog box:

Pl ease speci f y a val i d mode number .

Be sure to select the Animation tool in the Main toolbox.

15Build ing and Simulating a Flexible ModelI ti ti M d

7/27/2019 flex_gs_2012.1.2

19/34

Investigating Modes

Changing the Deformation Scale

In this section, youll exaggerate the amount the flexible body deforms so you can see deformations that

might otherwise be too subtle to observe. The default scale factor is 1.

1. At the bottom of the Flexible Body Modify dialog box, move the Deformation Scale Factor

slider to a value between 2 and 5.

2. In the Animation container on the Main toolbox, select the Play tool to restart the animation.

Adams/Flex now exaggerates the deformations of the flexible body by the amount you requested.

The flexible body also appears to be detached from the sphere and from its connection with

ground. This is because the motion of a point in a flexible body is the sum of the deformation that

is scaled and a rigid body motion that is not scaled.

3. In the Deformation ScaleFactor text box, enter1.0 to set the deformation scale back to 1.0.

4. Select Apply.

Getting Started Using Adams/FlexModifying the Modal Content

16

7/27/2019 flex_gs_2012.1.2

20/34


Modifying the Modal ContentOne of the keys to successfully simulating flexible bodies is having the right modal content. In many

cases, an MNF has more modes than you need to simulate a particular response. Using Adams/Flex, youcan select the modes that you want included in the flexible body. You can disable a particular mode if it

does not contribute to the overall response of a flexible body. You can also remove low influence modes

if they are slowing down the simulation of your model. You can disable modes based on their mode

number, frequency, or contribution of strain energy. You can also disable modes one at a time or disable

a range of modes.

In this section, youll use the Flexible Body Modify dialog box to display the different modes in the

flexible body, examine them, and then disable them based on their mode number and frequency.


Disabling Individual Modes

Disabling a Range of Modes

Simulating the Model with Disabled Modes


To display the Flexible Body Modify dialog box so you can modify the modal content:

1. From the Main toolbox, select the Select tool to reset the model.

2. Display the Flexible Body Modify dialog box, if necessary, as explained in Displaying the

Flexible Body Modify Dialog Box.

Disabling Individual Modes

The MNF file that you read into Adams/View contains 32 modes. Some of these modes are rigid body

modes, and Adams/Flex disables them by default. Because Adams/Flex supplies each flexible body with

its six nonlinear rigid body degrees-of-freedom, you do not need to nor should you include rigid body

modes.

In this section, youll view the first six modes (1 through 6), which are disabled because they are rigid

body modes. Youll also view the first mode that is enabled, mode 7, and disable it because it bends out-of-plane and is not needed for this simulation. Finally, youll disable other modes that do not contribute

to inplane motion. You disable the modes so the simulation of your model is more efficient.

To disable modes one at a time:

1. From the Flexible Body Modify dialog box, select the Next Mode tool to view the first

available mode (mode 1). The mode appears on the undeformed flexible body if the Superimpose

check box is selected. The Superimpose check box controls whether the undeformed shape is

superimposed on the deformed shape.

17Build ing and Simulating a Flexible ModelModifying the Modal Content

7/27/2019 flex_gs_2012.1.2

21/34


2. From the Flexible Body Modify dialog box, select the Animate tool to animate the mode. By

default, Adams/View runs the animation 3 times or through 3 cycles.

The mode you are currently animating is a rigid body mode and is disabled. To tell if a mode isdisabled, Adams/Flex selects the Disable radio button and displays the modes number and

frequency in parenthesis on the Flexible Body Modify dialog box.

3. Select the Next Mode tool until you reach mode 7 or, in the Mode Number text box, type 7

and press Enter.

Mode 7 is the first flexural mode that bends out-of-plane and is the first enabled mode. Because

the event you are modeling is inplane, you can disable this mode to improve efficiency.

To view the out-of-plane mode better, look at the model from a top view by selecting T(uppercase) in the main window.

4. Select Disable to disable mode 7. The mode number and its natural frequency now appear in

parentheses.

5. Change to mode 8. This is the first inplane bending mode.

6. Use the Contour, Datum Node, andDeformation Scale Factor settings to modify the

appearance of mode 8 so you can view it more easily. Ensure that mode 8 is enabled; it is critical

for the motion you are trying to capture.7. Examine the remaining mode shapes and disable them if they do not contribute to inplane motion.

If in doubt, leave the modes enabled. Remember, however, that disabling modes results in more

efficient simulations. Therefore, by leaving those modes that do not contribute to inplane motion

enabled, you will not see significant improvements in your simulation time.

Disabling a Range of Modes

In this section, youll disable a range of modes by specifying to disable all modes that have a frequency

of 10000Hz or higher.

To disable a range of modes:

1. From the Flexible Body Modify dialog box, select range.

The Enable or Disable a Range of Modes dialog box appears. This dialog box is very useful when

you have a large number of modes that you are managing. It lets you enable and disable ranges of

modes by either their mode number or their frequency.

Getting Started Using Adams/FlexModifying the Modal Content

18

7/27/2019 flex_gs_2012.1.2

22/34

y g

2. From the third pull-down menu from the left, select above and enter10000 in the text box that

appears next to the pull-down menu.

3. Select OK.

Simulating the Model with Disabled Modes

Now that youve disabled the modes in your model that do not contribute to inplane motion, run the

simulation again as explained below. You should notice an improvement in simulation time.

To simulate the model:

1. From the Flexible Body Modify dialog box, reset the deformation scale factor to 1, set Plot Types

to Contour, and set Datum Node to 1000.

2. Select OK.

3. Now repeat the simulation as explained in Simulating the Flexible Model. Depending on how

many modes you disabled, the simulation time should decrease.

You should use caution when disabling modes, however. Once you disable a mode, the flexible body

cannot take on the particular shape of the disabled mode. This is the same as applying a constraint to themodel. If you were to remove all out-of-plane modes from the example, the flexible body would behave

like a rigid body when responding to out-of-plane loads.

19Build ing and Simulating a Flexible ModelViewing Numeric Results

7/27/2019 flex_gs_2012.1.2

23/34

g

Viewing Numeric ResultsBy default, when you include a flexible body in your model, Adams/View measures specific attributes

of the flexible body, as well attributes of markers and points on the flexible body. For a listing of themeasures that Adams/View automatically tracks, see the Adams/Flex online help (under the Results tab),

and for more information on measures, see the Adams/View online help (under the Test tab).

In this section, youll view the measures that Adams/View has tracked during the latest simulation in the

plotting window. Youll set the plotting window to surf so that you can quickly view each measure plotted

against time without having to add pages to the plotting window.

To view plots o f the measures:1. In the Main toolbox, select the PostProcessing tool .

The Adams/PostProcessor plotting window appears with no plots displayed.

2. In the dashboard that appears along the bottom of the screen, set Source to Objects.

3. From the Filter list, select body and then, from the Object list, select FLEX_BODY_1.

4. Select a characteristic and component of the flexible body to measure. Start by selecting CM

Position and Y to view the position of the center of mass of the flexible body over time.5. Select Surfon the right of the dashboard.

6. Continue selecting characteristics and components of the flexible body to view. You may find

interesting the translational deformation of markers on the flexible body, particularly in the y

direction. Notice that the deformations are relative to the LBRF of the flexible body regardless of

whether you set a different datum node.

7. When you are done, from the File menu, select Close Plot Window to return to the Adams/View

main window.

1Exchanging a Rigid Body with a Flexible Body

7/27/2019 flex_gs_2012.1.2

24/34

Exchanging a Rigid Body with a Flexible

Body

Getting Started Using Adams/FlexOverview

2

7/27/2019 flex_gs_2012.1.2

25/34

OverviewOne of the keys to successful modeling is to start gradually and add complexity to your model as you

need it. We call this the crawl-walk-run approach. For example, the first time you simulate a new model,your primary concern may be its overall performance. As you refine your design, however, you can add

complexity, such as the flexibility of key parts. Using Adams/Flex and Adams/View together, you can

very easily add flexibility to your model after your initial design is complete, as shown in this tutorial.

The tutorial also illustrates that often you cannot simulate a model until you add flexibility to it.

The tutorial contains the following sections:

What Youll Create

Starting Adams/View and Importing a File

Simulating the Rigid Fourbar

Adding a Flexible Link

Positioning the Flexible Link

Reviewing Connections

Simulating the Flexible Fourbar

3Exchanging a Rigid Body with a Flexible BodyWhat Youll Create

7/27/2019 flex_gs_2012.1.2

26/34

What Youl l CreateIn the tutorial, youll import into Adams/View a command file that contains a rigid model of a fourbar.

Youll then replace one of the rigid links with a flexible link.

Until you replace the rigid link with a flexible link, Adams/Solvercannot simulate the motion of the

fourbar because one of its joints (JOINT_3) is skewed by 1 degree. The skewing of the joint requires the

motion of the fourbar to be out-of-plane. Because the links are rigid, however, they cannot deflect out-

of-plane and, thus, the simulation fails. Adding a flexible link that bends allows the fourbar to move.

The following figure shows the fourbar model, the joint that is skewed, and the rigid link that youll

replace with a flexible link. The flexible link that youll use to replace the rigid link is actually the same

flexible link you used in the first tutorial to create a cantilever link.

Figure 1 Fourbar Model

Rigid link (PART_2)

to be replaced

Joint (JOINT_3)skewed by 1 degree

Getting Started Using Adams/FlexStarting Adams/View and Importing a File

4

7/27/2019 flex_gs_2012.1.2

27/34

Starting Adams/View and Importing a FileYoull start the tutorial by running Adams/View and importing a command file to create a model called

model_1.

To start Adams/View and create your database:

1. Start Adams/View, if necessary, as explained in Starting Adams/View and Creating a Database.

The Adams/View main window appears.

2. From the Welcome dialog box, select Import a file.

3. Select OK.

The File Import dialog box appears.

4. Right-click the File to Read text box, and point to Search.

5. From the shortcut menu, select the flex/examples directory

(avi ew_di r / . . / f l ex/ exampl es).

The Select File dialog box appears.

6. In the fourbar folder, select the file rigid.cmd, and then select OK.

7. Select OK.

A fourbar model like the one shown in the figure above appears.

5Exchanging a Rigid Body with a Flexible BodySimulating the Rigid Fourbar
http://2_tutor.pdf/http://2_tutor.pdf/

7/27/2019 flex_gs_2012.1.2

28/34

Simulating the Rigid FourbarYoull now try to simulate the fourbar that you imported into your modeling database. You will not,

however, be able to simulate it. Instead, youll receive an error in the message window.

To simulate the rigid fourbar:

1. From the Main toolbox, select the Simulate tool .

2. In the Simulation container of the Main toolbox, select the Simulation Start tool .

The simulation fails and the following error message appears:

ERROR: No conver gence was achi eved af t er 25 i t erat i ons whi l esol vi ng f or t he ki nemat i c di spl acement s. ERROR: Si mul at i on f ai l ur edet ect ed

3. Closely examine the model to see that the joints are misaligned making the mechanism locked

and, therefore, unable to simulate. Weve intentionally added this misalignment to highlight the

impact flexibility can have on your model.

Getting Started Using Adams/FlexAdding a Flexible Link

6

7/27/2019 flex_gs_2012.1.2

29/34

Adding a Flexible LinkThe next step is to indicate the rigid link you want to replace and the replacement flexible link. You will

use the Rigid to Flex swapping feature.

To add a flexible link:

1. From the Main toolbox, select the Select tool to reset the model.

2. Select the upper link, PART_2.

3. From the Build menu, point to Flexible Bodies, and then select Rigid To Flex.

The Swap a rigid body for a flexible body dialog box appears. Notice that the Current Part text

box already has the name of the link you selected.

4. Right-click the MNF File text box, and then, from the shortcut menu, point to Search.

5. From the shortcut menu, select the flex/examples/mnfdirectory

(avi ew_di r / . . / f l ex/ exampl es/ mnf).

6. In the Select File dialog box, select the file link.mnf, and then select Open.

A 0.5 meter long flexible link appears in Adams/View.

Note: You may need to move the Swap a rigid body dialog box if it blocks your view of the body.

7Exchanging a Rigid Body with a Flexible BodyPositioning the Flexible Link

7/27/2019 flex_gs_2012.1.2

30/34

Positioning the Flexible LinkCurrently, the link is not positioned where it needs to be. There are three positioning tools available:

Align flexible body CM with CM of current part

Launch Precision Move dialog box

Specify three point pairs to define the location and orientation

In this tutorial, youll use the first two.

To position the flexible link based on the center of mass (CM):

In the Swap a rigid body for flexible body dialog box, select the Align Flex Body CM with CM

of Current Part button.

Adams/Flex moves the link so the CM of the rigid and flexible links align.

Keep in mind that the finite element discretization of a solid will naturally have an inertia tensor

and CM location that is slightly different than that of an analytical solid, due in large part to the

facetization. Therefore, you may find that you need to make small precise adjustments to the

position and/or orientation of the flexible body so it fits correctly into the rest of your model.

To position the flexible link precisely:

1. In the Swap a rigid body for flexible body dialog box, select the Launch Precision Move Panel

button.

The Precision Move dialog box appears, as shown in the figure below. Notice that many of the

text boxes have been automatically filled in with the position and orientation of the flexible body

relative to the ground coordinate system.

Figure 2 Precision Move Dialog Box

The C1, C2, and C3 text boxes display the location of the flexible body with much precision:

Values already

entered

Getting Started Using Adams/FlexPositioning the Flexible Link

8

7/27/2019 flex_gs_2012.1.2

31/34

-250.0000107801, 250.0, 0.0

The A1, A2, and A3 text boxes display the angular orientation, and they appear acceptable:

0.0, 0.0, 0.02. Clear the C1 text box, and enter the value: -250.

3. Select OK.

The location of the link has now been corrected to a higher level of position.

9Exchanging a Rigid Body with a Flexible BodyReviewing Connections

7/27/2019 flex_gs_2012.1.2

32/34

Reviewing ConnectionsIt is a good idea to review the connections that will be established for you between the link and the rest

of the model. As part of the swapping operation, all the markers on the rigid body will be transferred tothe flexible body, thereby establishing connections to the flexible body.

1. In the Swap a rigid body for a flexible body dialog box, select the Connections tab.

2. Verify that Sort By is set to Marker (it is on the far right of the dialog box).

The Markers and Nodes table appears, as shown below. Notice that it has identified a list of

markers on the rigid link that will be transferred to the flexible link. The Connections column

identifies the names of constraints or forces that exist on the rigid body that you are replacing. The

nodes on the flexible body that are nearest to the markers are listed in the Node ID column.

Figure 3 Marker and Nodes Table

3. Notice that the Distance column is reporting the distance between the nearest node and the rigid

body marker that will be transferred to the flexible body.

Because you have positioned the flexible body precisely, the connections are coincident withnodes and the distances are 0.00 for the markers (MAR_1 through MAR_4).

Note: You can display more digits of precision by entering a value in the Number of digits text

box.

Distance

column

Getting Started Using Adams/FlexReviewing Connections

10

7/27/2019 flex_gs_2012.1.2

33/34

The CM marker distance is nonzero because the finite element mesh was not constructed to have

a node at the CM. This is a very common scenario and is not really a problem because it can be

automatically moved to the nearest node by default.

Keep in mind that the flexible body already has its own CM so you can safely ignore the CM

marker on the rigid body and just let it move to the nearest node. To demonstrate the

move/preserve feature of the dialog box, however, you will preserve the location.

4. Select the Distance cell (13.34) for the CM.

5. Select the Preserve Location button.

The cell in the Move column has now been updated to loc. This means that the location of the CM

marker will be preserved and it will not be moved to the nearest node when it is transferred to the

flexible body.

6. Select OK.

The flexible body has been swapped, the rigid body deleted, and all connections to the model have

been established.

11Exchanging a Rigid Body with a Flexible BodySimulating the Flexible Fourbar

7/27/2019 flex_gs_2012.1.2

34/34

Simulating the Flexible FourbarYoull now simulate the fourbar using default values. The simulation will now be successful.

To simulate the rigid fourbar:

1. In the Main toolbox, select the Simulate tool .

2. Select the Simulation Start tool .

Documents

flex_gs_2012.1.2