Embed Size (px)
Citation preview
VT03deTechnical Information
Drywall Systems
2019-09
Fastening of Loads to Knauf Wall and Ceiling SystemsKnauf TraversesKnauf SanistandsKnauf BoardsKnauf Anchoring
Note on English translation Hinweise zur englischen FassungThis is a translation of the technical information sheet valid in Germany All stated details and properties are in compliance with the regulations of the German standards and building regulations They are only applicable for the specified products system components application rules and construction details in connection with the specifications of the respective cer-tificates and approvalsKnauf Gips KG denies any liability for applications outside of Germany as this requires changes acc to the respective national standards and building regulations
2
Usage instructionsNotes on the documentKnauf technical information documents are the planning and application basis for planners and professional installers with the application of Knauf systems The contained information and specifications constructions details and stated products are based unless otherwise stated on the certificates of usability (eg National Technical Test Certificate (abP) andor German National Technical Approvals (abZ)) valid at the date they are published as well as on the applicable standards In addition design and structural requirements and those regarding building physics (fire protection and sound insulation) are considered The contained construction details are examples and can be used in a similar way for various cladding variants of the respective system At the same time the demands made on fire resistance andor sound insulation as well as any necessary additional measures andor limitations must be observed
References to other documents Metal stud partitions see system data sheet W11de Knauf Metal Stud Partitions
Wood frame partitions see system data sheet W12de Knauf Wood Frame Partitions
Fire walls see system data sheet W13de Knauf Fire Walls Furring and linings see system data sheet W61de Knauf Furring and Linings Metal Stud Partitions AQUAPANELreg see system data sheet W38de Knauf Metal Stud Partitions AQUAPANELreg
Board Ceilings ndash suspended under solid ceilings see system data sheet D11de Knauf Board Ceilings
ContentsUsage instructions 2Intended use of Knauf Systems 2
Loads on partitions and furringsIntroduction 3Cantilever loads 4
Rating diagrams 4Fastening in the cladding 6
Fields of application 6Fixing loads 6Rating 7
Anchoring in the traverses 8Fields of application 8Fixing loads 8Rating 9Knauf multi-purpose traverses 10Knauf steel anchoring traverse with gypsum fibre insert 12Knauf steel anchoring traverse 14
Full-length Sanistand 15
Loads on board ceilingsFastening in the cladding grid 21Anchoring in the traverses 22
Knauf multi-purpose traverses 22
Board ceilings under wood joist ceilings see system data sheet D15de Knauf wood joist ceiling systems
Observe the product data sheets of the individual Knauf system components
Intended use of Knauf SystemsPlease observe the following
Caution
Knauf systems may only be used for the application cases as stated in the Knauf documentation In case third-party products or components are used they must be recommended or approved by Knauf Flawless application of productssystems assumes proper transport storage assembly installation and maintenance
3
Loads on partitions and furringsIntroduction
Loads on partitions and furringsPartitions and furrings as drywall constructions are mainly non-load bearing constructions in keeping with the DIN EN 1991 standard The excellent performance of the Knauf partitions in combination with additional measures such as installed traverses or metal laminated hard gypsum boards offers solutions for the implementation of constructional challengesThis technical information document contains recommendations for the fastening and fixing of loads on partitions and furrings in the form of
Cantilever loads from static superimposed loads (cabinets shelves heating elements)
Dynamic loads such as handrails folding handles and fold-down seats acc to DIN 18 040 Construction of accessible buildings
Attachment of the WC bidet and washbasin using sanitary mounts in metal stud partitions
Normative definition of the loads on lightweight partitions are defined for example in the DIN 4103 DIN 18183 as well as in acc to Code of Practice No 8 of the Bundesverband der Gipsindustrie eV German Gypsum AssociationCantilever loads as described in the DIN 4103 are considered to be permanent loads and apply for example to cabinetsDynamic loads result from folding handles and fold-down seats Dynamic loads are recurring loads effective for a short duration and are time-dependentFor folding handles a projection of 80 cm with a load of 100 kN is assumed for the following recommendations Fold-down seats are considered as a maximum load of 150 kN with a projection of 48 cm Sanistands are offered by different manufacturers and are described normatively depending on the application whether toilet pans or washbasins The fracture load for toilet pans acc to the EN 997 stipulates 400 kN and for washbasins acc to EN 14688 a load of 150 kN is stipulatedThe Knauf partition systems in the following have been examined for the case above and determined to be appropriate for the load
Note
Fasteners in acc to DIN 4103 section 515 are to be used The details contained in this technical information document have been tested in the course of mechanical tests by Knauf
Differentiation cantilever load fixing loadTwo aspects must be considered in the attachment of loads on partitions and furrings
Cantilever loads
F F F F F F F
F
FFF
F F F
The cantilever load acts as a linear distributed load on the entire wallpartition system ie the entire wall system must be specifically designed for the purpose and the load must be transferred to the supporting structure without permitting a structural failure or deformation which exceed the limits of serviceability
Fixing loads
FF
The fastening of cantilever loads to partition systems are undertaken over several anchoring points which must be considered separately with respect to their loadbearing capacity in dependence on the selected fasteneranchor and the cladding as well as the substrate (cladding profile traverse)
Knauf system benefits Regulated construction High crack resistance with coordinated gypsum board types Diamant Steel GKFI as a surface traverse for flexible attachment in the entire wall area even with subsequent installation
4
Loads on partitions and furringsCantilever loads
Rating diagrams
Cabinet widthCabinet depth
Cabin
et he
ight
ge 30
0 mm
le 600 mmle 1200 mm
Eccentricityle 300 mm
The specified permissible cantilever loads are in accordance with the DIN 18183 or DIN 4103-1 at an eccentricity (spacing of load resulting to the wall surface) of max 300 mm The permissible load is reduced accordingly with greater eccentricity The following tables and diagrams are intended as an aid in the determination of the permissible cantilever loads with divergent eccentricity The values can be taken either from the tables or the diagrams
Up to 04 kNm (40 kgm) wall lengthMaximum permissible cabinet weight (kg) acc to table
Cabinet widthmm
Cabinet depthmm100 200 300 400 500 600
400 31 28 25 22 19 16600 465 42 375 33 285 24800 62 56 50 44 38 321000 775 70 625 55 475 401200 93 84 75 66 57 48
Assume the worst-case value with intermediate values or diagram procedure
orMaximum permissible cabinet weight (kg) acc to diagram
10
70
60
40
20
100
80
90
50
Cabinet depthmm 100 200 300 400 500 600
1000 800 600 400
30
Max permissible cabinet weight
kg
Cabinet width
mm1200
Up to 07 kNm (70 kgm) wall length Maximum permissible cabinet weight (kg) acc to table
Cabinet widthmm
Cabinet depthmm100 200 300 400 500 600
400 43 40 37 34 31 28600 645 60 555 51 465 42800 86 80 74 68 62 561000 1075 100 925 85 775 701200 129 120 111 102 93 84
Assume the worst-case value with intermediate values or diagram procedure
orMaximum permissible cabinet weight (kg) acc to diagram
kg
Max permissible cabinet weight
Cabinet width
mm1200
1000
400
600
800
mmCabinet depth
600100 200 300 400 500
10
70
60
40
20
30
100
80
90
110
120
50
5
Loads on partitions and furringsCantilever loads
Up to 10 kNm (100 kgm) wall lengthMaximum permissible cabinet weight (kg) acc to table
Cabinet widthmm
Cabinet depthmm100 200 300 400 500 600
400 90 80 70 60 50 40600 135 120 105 90 75 60800 180 160 140 120 100 801000 225 200 175 150 125 1001200 270 240 210 180 150 120
Assume the worst-case value with intermediate values or diagram procedure
orMaximum permissible cabinet weight (kg) acc to diagramMax permissible cabinet weight
kgCabinet width
mm1200
400
1000
600
800
Cabinet depthmm 600100 200 300 400 500
20
140
120
80
40
60
200
160
180
100
240
220
260
280
300
Up to 15 kNm (150 kgm) wall lengthMaximum permissible cabinet weight (kg) acc to table
Cabinet widthmm
Cabinet depthmm100 200 300 400 500 600
400 135 120 105 90 75 60600 202 180 157 135 112 90800 270 240 210 180 150 1201000 337 300 262 225 187 1501200 360 360 315 270 225 180
Assume the worst-case value with intermediate values or diagram procedure
orMaximum permissible cabinet weight (kg) acc to diagram
400
mm
1000
1200
600
800
Max permissible cabinet weight
kgCabinet width
Cabinet depthmm 600500400300200100
20
140
120
80
40
60
200
160
180
100
240
220
260
280
300
320
340
6
Loads on partitions and furringsFastening in the cladding
Fields of applicationAccording to DIN 18183 the metal stud partitions and independent furrings can be loaded at any position by cantilever loads
Up to 04 kNm (40 kgm) wall length Cladding thickness ge 125 mm Knauf boards Up to 07 kNm (70 kgm) wall length Cladding thickness ge 15 mm Diamant (in acc to abP P-140592810) ge 18 mm Knauf boards
With Diamant Steel GKFI and a cover layer ge 125 mm Diamant GKFI (see following table) cantilever loads up to 15 kNm (150 kgm) on walls are possible
Selection of the grid in dependence on the expected loadLoad max Load
typeProfile min Cladding thickness min Furring
possibleLoaded side Unloaded sideKn
auf
Boar
ds
Diam
ant
Diam
ant
Stee
l GKF
I Minimum thickness
Knau
f Bo
ards
Diam
ant
Diam
ant
Stee
l GKF
I Minimum thickness
tmm
tmmkNm2
04 StaticCW 50 125 125 YesCW 50 125 125 Yes
07 StaticCW 50 125 + 04 125 + 04 Yes 2)
CW 75 18 18 Yes 2)
CW 75 15 15 Yes 2)
10 StaticCW 50
125 + 041) + 125 2x 125 Yes
CW 75 125 + 04 125 No
15 Static CW 75 125 + 04
+ 125 2x 125 No
1)ScrewspacingDrywallScrewsXTB1stlayerDiamantSteelGKFIle250mm2)IncaseofapplicationofpartitionheightsacctoDIN18183-1onlycantileverloadsupto04kNmarepossible
Fixing loadsFor fixing of cantilever loads
Dowel screw Maximum screw dowel load capacity in kgX-hooks Knauf Cavity Dowel
HartmutScrew M5
fischer MHD 5 x 65 SScrew M5 or M6
Knauf Multi-Purpose Screw FN 43 x 65
Plastic cavity dowelOslash 8 or 10 mm
Diamant125 mm 5 10 15 40 20 13 3015 18 mm 5 10 15 45 25 14 352x 125 mm 5 10 15 60 30 20 45ge 2x 125 mm 5 10 15 65 35 40 50Diamant Steel GKFI1x 125 + 04 mm 5 10 15 80 50 30 30 3)
2x 125 + 04 mm 5 10 15 100 90 60 55 3)
Measuredwith300mmeccentricity3)ValuesapplywithfischerplasticcavitydowelsUX8x50withKnaufMulti-PurposeScrewFN43x65orequivalent
Notes
Static loads in this respect are permanently fastened loads such as towel rails cabinets shelves and boilers Dynamic loads are exerted by fastened components which are subjected to continuous changes in load such as handrails fold-down seats and folding handles The use of traverses is required here see page 8Always screw fasten Diamant Steel GKFI with Diamant Screws XTB even for a cover layer of Diamant
7
Loads on partitions and furringsAnchoring in the cladding
RatingThe specified permissible cantilever loads are in accordance with the DIN 18183 or DIN 4103-1 at an eccentricity (spacing of resulting load to the wall surface) of max 300 mm The permissible load is reduced accordingly with greater eccentricity The determination of the permissible cantilever loads with divergent eccentricity is undertaken using the tables or diagrams on page 4 and page 5
Rating examples Determination of the permissible cabinet weight as well as the required minimum number of dowels (always ge 2)Metal stud partition W111de CW 50 cladding 125 mm Diamant GKFI acc to tableField of application static load max cantilever load 04 kNm (40 kgm) wall length Cabinet
widthCabinet depthmm
mm 100 200 300 400 500 600
400 31 28 25 22 19 16
600 465 42 375 33 285 24
800 62 56 50 44 38 32
1000 775 70 625 55 475 40
1200 93 84 75 66 57 48
Cabinet depth 400 mm cabinet width 1000 mm Max cabinet weight 55 kg
Cladding thickness 125 mm plastic cavity dowel
Max dowel load 30 kg
Required number of dowels 55 kg 30 kg = 18 2 dowels
are the min necessary
Metal stud partition W111de CW 75 cladding 2x 125 mm Diamant GKFI acc to diagramField of application static load max cantilever load 07 kNm (70 kgm) wall length
400
mm12001000
600
100 200 400 500 600mm
10
70
60
40
20 30
kg
100
80 90
110120
800
300
50
1
23
450
65
Cabinet depth
Cabinet width
Max permissible cabinet weightCabinet depth 450 mm cabinet width 800 mm
With cabinet depth 450 mm 1 vertically upwards up to the cabinet width line 800 mm
2 at the intersection point horizontal to the left ndash read off value 3
Max cabinet weight 65 kg
Cladding thickness 2x 125 mm Knauf Cavity Dowel Hartmut
Max dowel load 60 kg
Required number of dowels 65 kg 60 kg = 108 2 dowels
are the min necessary
8
Fields of applicationTraverses are built-in elements in lightweight partitions that transfer the fastening loads directly into the grid or into the flanking solid constructions
Selection of the traverse and grid in dependence on the expected loadFastening Load max Load type Profile min Cladding thickness min Independent
furring possible
Knauf Boards DiamantkNm2 mm mm
Steel anchoring traversesee page 14
07 Static CW 50 125 125 No07 Static CW 50 18 15 Yes10 Static CW 75 125 125 No10 Static CW 50 18 15 Yes
Metal traverse with gypsum fibre insertsee page 12
07 Static CW 50 125 125 No07 Static CW 50 18 15 Yes10 Static CW 75 125 125 No10 Static CW 50 18 15 Yes15 Static CW 50 18 15 No15 Static UA 50 18 15 Yes15 Dynamic UA 75 18 15 Yes
Multi-purpose traversesee page 10
07 Static CW 50 125 125 No07 Static CW 50 18 15 Yes10 Static CW 75 125 125 No10 Static CW 50 18 15 Yes15 Static CW 50 18 15 No15 Static UA 50 18 15 Yes15 Dynamic UA 75 18 15 Yes
Fixing loadsFor fixing of cantilever loads
Dowel screw Maximum screw dowel load capacity in kgKnauf Cavity Dowel Hartmut
fischer MHD 5 x 65 S
Knauf Multi- Purpose Screw FN 43 x 65
fischer plastic cavity dowels 8 x 50 with Knauf Multi-Purpose Screw FN 43 x 65
Wood screw Oslash 50 mm
Wood screw Oslash 60 mm
TraversesSteel anchoring traverse 75 ndash 45 40 45 45
Metal traversewith gypsum fibre insert
90 75 65 46 55 70
Multi-purpose traverse ndash ndash 125 ndash 115 165
Measuredwith300mmeccentricity
Loads on partitions and furringsAnchoring in the traverses
NotesStatic loads in this respect are permanently fastened loads such as towel rails cabinets shelves and boilers Dynamic loads are exerted by fastened components which are subjected to continuous changes in load such as handrails fold-down seats and folding handles
9
Loads on partitions and furringsAnchoring in the traverses
RatingThe specified permissible cantilever loads are in accordance with the DIN 18183 or DIN 4103-1 at an eccentricity (spacing of resulting load to the wall surface) of max 300 mm The permissible load is reduced accordingly with greater eccentricity The determination of the permissible cantilever loads with divergent eccentricity is undertaken using the tables or diagrams on page 4 and page 5
Rating examples Determination of the permissible cabinet weight as well as the required minimum number of dowels (always ge 2)Metal stud partition W111de CW 50 cladding 18 mm Knauf board acc to tableField of application static load max cantilever load 07 kNm (70 kgm) wall length Cabinet
widthCabinet depthmm
mm 100 200 300 400 500 600400 43 40 37 34 31 28600 645 60 555 51 465 42800 86 80 74 68 62 561000 1075 100 925 85 775 701200 129 120 111 102 93 84
Cabinet depth 500 mm cabinet width 800 mm Max cabinet weight 62 kg Fixing traverse Knauf Multi-Purpose Screw FN 43 x 65
Max screw load 45 kg
Required number of screws 62 kg 45 kg = 14 2 screws
are the min necessary
Metal stud partition W111de UA 75 cladding 15 mm Diamant GKFI acc to diagram
Field of application dynamic load max cantilever load 15 kNm (150 kgm) wall length
20
400
Cabinet depth100 200 600
Max permissible cabinet weight
140120
80
4060
kg
200
160
180
Cabinet width
mm
1000
1200
600
mm 300
100 800
240220
260280300320340
450400 500
165
1
23
Cabinet depth 450 mm cabinet width 800 mm
With cabinet depth 450 mm 1 vertically upwards up to the cabinet width line 800 mm
2 at the intersection point horizontal to the left read off value 3
Max cabinet weight 165 kg
Multi-purpose traverse Knauf Multi-Purpose Screw FN 43 x 65
Max screw load 125 kg
Required number of screws 165 kg 125 kg = 13 2 screws
are the min necessary
10
Knauf multi-purpose traversesThe multi-purpose traverse is suitable for accepting loads attached to the wall up to 15 kNm wall length eg cupboards boilers folding wall attached seats folding handles and similarThe multi-purpose traverse consists of a 23 mm thick multi-layer wooden board and galvanized sheet metal profiles It is fastened to the side of the floor-to-ceiling profilesThe attachment of the loads to the traverses should be performed using Knauf Multi-Purpose Screw FN
NoteTraverses for installation in damp and wet rooms see also system data sheet W38de Knauf Metal Stud Partitions AQUAPANELreg
Loads on partitions and furringsAnchoring in the traverses
Installation and applicationMulti-purpose traverse made of multi-layer wooden board and galvanized sheet metal profiles attached to the side of the CW studs UA profiles For CW studs screw fasten using the 6 enclosed Metal Screws LN 35 x 11 mm (3 per side) For UA profiles screw fasten with the 6 enclosed Drilling Screws ST 42 x 13 mm (3 per side)Arrangement in a rowUA profiles CW studs
Direction of installation Direction of installation
11
Loads on partitions and furringsAnchoring in the traverses
W234de-A10 View ndash Design with UA profile W234de-A13 View ndash Design with CW stud
W234de-H10 Horizontal section ndash Design with UA profile W234de-H13 Horizontal section ndash Design with CW studeg W626de eg W626de
W234de-V10 Vertical section ndash Design with UA profile W234de-V13 Vertical section ndash Design with CW studeg W116de eg W112de
Wooden board 555
Stud spacing 625 (grid dimension)
300
Multi-purpose traverse555 300 23 mm
Multi-layer wooden board
UA profile
Drillingscrew ST42 x 13(enclosed)
Wooden board 555
Stud spacing 625 (grid dimension)
300 Metal screw
LN 35 x 11(enclosed)
Multi-purpose traverse555 300 23 mm
Multi-layer wooden board
CW stud
Wooden board 555
Stud spacing 625 (grid dimension)
300
Multi-purpose traverse555 300 23 mm
UA profileDrilling screwST 42 x 13
Multi-purpose traverse555 300 23 mm
CW studMetal screwLN 35 x 11
48
eg folding wallattached seat
Knauf boardstrips
eg Supporthandle maxprojection 800 mm
Multi-purposetraverseUA profileKnauf boards
48
Multi-purposetraverseCW studKnauf boards
eg Cabinet
Scale 110 I Dimensions in mmDetails
Note No web cutouts in the CW studs are permissible for traverses to which the CW studs are attached
12
Knauf steel anchoring traverse with gypsum fibre insertThe steel anchoring traverse with gypsum fibre insert is suitable for accepting loads attached to the wall up to 15 kNm wall length eg cupboards shelves handrails and similarThe metal traverse with gypsum fibre insert consists of 075 mm thick sheet metal as well as an 18 mm thick gypsum fibre board It is fastened to the side of the floor-to-ceiling profiles The attachment of the loads to the traverses should be performed using Knauf Multi-Purpose Screw FNUse in partition systems where the requirement for non-combustible reaction to fire exists
Installation and applicationSteel anchoring traverse made of galvanized steel with gypsum fibre insert fastened to the CW studs UA profiles In case of CW studs crimp using a Stud Crimper and for UA profiles screw fasten with 6 Drilling screws LB 35 x 16 mmArrangement in a rowUA profiles CW studs
Loads on partitions and furringsAnchoring in the traverses
13
Scale 110 I Dimensions in mmDetailsW234de-A12 View - Design with UA profile W234de-A14 View - Design with CW stud
W234de-H12 Horizontal section - Design with UA profile W234de-H14 Horizontal section - Design with CW studeg W112de eg W112de
W234de-V12 Vertical section - Design with UA profile W234de-V14 Vertical section - Design with CW studeg W112de eg W112de
Traverse dimension 620
Stud spacing 625 (grid dimension)
290
Steel anchoring traversewith gypsum fibre insert
Traverse attached to UA profileusing drilling screws
UA profile
Steel anchoring traversewith gypsum fibre insert
CW stud
Crimp the traverse to the CW studusing a stud crimper
Traverse dimension 620
Stud spacing 625 (grid dimension)
290
Drilling screwLB 35 x 16
Steel anchoringtraverse with gypsum
fibre insert
UA profile Crimped Steel anchoring traversewith gypsum fibre insert
CW stud
eg Handrail
UA profileKnauf boards
Steel anchoring traversewith gypsum fibre insert
eg Handrail
CW studKnauf board
Steel anchoring traversewith gypsum fibre insert
Loads on partitions and furringsAnchoring in the traverses
Note No web cutouts in the CW studs are permissible for traverses to which the CW studs are attached
14
Loads on partitions and furringsAnchoring in the traverses
Knauf steel anchoring traverseThe steel anchoring traverse is suitable for accepting loads attached to the wall up to 10 kNm wall length eg towel holders cupboards shelves and similar Not suitable for dynamic loads such as folding wall attached seatsThe steel anchoring traverse consists of 075 mm thick sheet metal and are crimped onto the side using a stud crimper on the CW studs Particularly suitable for single-layer clad metal stud partitions and furrings where in case of cantilever loads gt 04 kNm (400 kgm) wall length the installation of a traverse is required
NoteTraverses for installation in damp and wet rooms see also system data sheet W38de Knauf Metal Stud Partitions AQUAPANELreg
Installation and applicationCrimp the steel anchoring traverse made of galvanized sheet steel to the CW studs using a Stud CrimperAdditional screw fastening of the steel anchoring traverse via screw fastening of the cladding (min 2 to 3 anchoring points) Reduce the screw spacing of the cladding if necessaryArrangement in a rowCW studs
Scale 110 I Dimensions in mmDetailsW234de-A11 View W234de V11 Vertical section
eg W111de
W234de-H11 Horizontal sectioneg W111de
Sheet metal gauge 075 mm
Steel anchoring traverse
CW stud
Crimp the traverse to the CW studusing the stud crimper
290
Traverse dimension 620
Stud spacing 625 (grid dimension)
eg Cabinet
CW stud
Knauf boardSteel anchoring traverse
Steel anchoring traverseCW stud
Crimped
Note No web cutouts in the CW studs are permissible for traverses to which the CW studs are attached
15
Full-length SanistandFloor-to-ceiling Sanistands made of galvanized UA profiles (min UA 75) 2 mm thick are suitable for transferring loads from traverses into the supporting structure or for fixing loads hanging onto walls such as school blackboards up to 15 kNm wall lengthFloor-to-ceiling Sanistands profiles are anchored to the basic floor and ceiling with door frame brackets or connection brackets for UA profiles The upper door frame bracket includes openings for routing cables such as pipe-in-pipe systems or electrical cablesThe loads are connected directly to the flange of the UA profile
W228de-A10 View
le 1000 mm
UW runnercontinuous
Door frameconnection brackettop connection withenclosed dowels
CW studAxial spacing suitedto partition system
UA profileas afloor-to-ceilingSanistand forbearing cantileverloads
UW runnercontinuous
Door frameconnection bracketbottom connectionwith enclosed dowels
Scale 110
Installation and applicationFloor-to-ceiling Sanistands made of UA profiles must be anchored to the basic floor and ceiling with door frame brackets or connection brackets for UA profiles The upper door frame bracket includes openings for routing cables such as pipe-in-pipe systems or electrical cables Fasten objects to UA profiles using threaded rods U washers and M1012 steel nuts or self-tapping screws
Loads on partitions and furringsFull-length Sanistand
Detail
Notes
Web cutouts are not permissible in UA Sanistand subject to cantilever loads point loads or linear distributed loadsMaximum screw load with connections to full height Sanistand (UA profile)Every UA profile flange and anchoring point may not exceed a resulting pull-out load of 150 kN (150 kg)Components similar to cantilevers such as foldable rails should be screwed onto two adjacent UA profilesUse suitable drilling screws eg Ejot Zebra Piasta Hilti S-MD or comparable
16
Loads on partitions and furringsFull-length Sanistand
Scale 110DetailsW116de-V1 Sanistand W116de-H1 SanistandVertical section I Without fire resistance Horizontal section I Without fire resistance
UW runnerUniflott + Trenn-Fix
UW runner
Additional UA profile
Sanistand withconcealed mount cistern
Knauf connectionbracket with enclosedM8 carriage bolts
Knauf conection bracket withenclosed M8 carriage bolt
2x 125 mm DiamantDiamant screw XTB
Additional CW stud
Knauf sealing tape
Board strip installationacc to W11de systemdata sheet
Stud spacing le 625 mm
CW stud profile
Additional CW studBoard strip installation in acc with W11de system data sheet
Knauf connection bracket withenclosed M8 carriage bolts
Additional UA profileSanitand with concealedmount cistern
Notes
Max partition height UA 50 = 300 m UA 75 = see system data sheet W11de Knauf Metal Stud Partition for the wall heights
Minimum cladding ge 18 mm Knauf Boards recommendation 2x 125 mm Knauf Diamant
Web cutouts are not permissible in UA Sanistand subject to cantilever loads point loads or linear distributed loadsObserve the manufacturersrsquo details for lateral UA profiles and cladding Additional UA profiles are required laterally on Sanistand mounts acc to DIN 18340 section 374 Only possible without additional UA profiles if the manufacturer of the Sanistand base or WC Sanistand permits itDeviating specifications of the Sanistand manufacturer must be considered and observed
17
Loads on partitions and furringsFull-length Sanistand
Notes
Max partition height rear W112de UA 50 = 300 m UA 75 = see system data sheet W11de Knauf Metal Stud Partition for the wall heights
Minimum cladding front wall installations ge 18 mm Knauf Boards recommendation 2x 125 mm Knauf Diamant
Web cutouts are not permissible in UA Sanistand subject to cantilever loads point loads or linear distributed loadsObserve the manufacturersrsquo details for lateral UA profiles and cladding Additional UA profiles are required laterally on Sanistand mounts acc to DIN 18340 section 374 Only possible without additional UA profiles if the manufacturer of the Sanistand base or WC Sanistand permits itDeviating specifications of the Sanistand manufacturer must be considered and observed
Scale 110DetailsW626Vde-V1 Without back anchoring W626Vde-H1 Without back anchoring Vertical section Horizontal section
UW runnerUniflott + Trenn-Fix
UW runner
Additional UA profile
Sanistand withconcealed mount cistern
Knauf connection bracket withenclosed M8 carriage bolt
Knauf connection bracket withenclosed M8 carriage bolt
2x 125 mm DiamantDiamant screw XTB
Knauf sealing tape
Sanistand withconcealed mount cisternKnauf connection bracket with
enclosed M8 carriage bolts
Stud spacing le 625 mm
UW runner
Knauf boardsCW stud
Additional UA profile
18
Loads on partitions and furringsFull-length Sanistand
Scale 110DetailsW626Vde-V2 Back anchoring in traverse W626Vde-H2 Back anchoring in traverse Vertical section Horizontal section
Sanistand withconcealed mount cistern
SealantUD profile made of insulation strips
UW runner
UW runner
UA profile
Knauf multi-purpose screw FN
Uniflott + Trenn-Fix
Multi-purpose traverse 555 300 23 mm
Knauf connection bracket withenclosed M8 carriage bolts
2x 125 mm DiamantDiamant screw XTB
Knauf connection bracket withenclosed M8 carriage bolt
Wall anchor installation acc to WCSanistand manufacturer specifications
Knauf sealing tape
Stud spacing le 625 mm
Multi-purpose traverse555 300 23 mm
UA profile
UA profile
Knauf connection bracket withenclosed M8 carriage bolt
Knauf connectionbracket with enclosedM8 carriage bolt
Wall anchorinstallation acc to
WC Sanistandmanufacturerspecifications
Notes
Max partition height rear W112de UA 50 = 300 m UA 75 = see system data sheet W11de Knauf Metal Stud Partitions for the wall heights
Minimum cladding front wall installations ge 18 mm Knauf Boards recommendation 2x 125 mm Knauf Diamant
Web cutouts are not permissible in UA Sanistand subject to cantilever loads point loads or linear distributed loadsObserve the manufacturersrsquo details for lateral UA profiles and cladding Additional UA profiles are required laterally on Sanistand mounts acc to DIN 18340 section 374 Only possible without additional UA profiles if the manufacturer of the Sanistand base or WC Sanistand permits itDeviating specifications of the Sanistand manufacturer must be considered and observed
19
Loads on partitions and furringsFull-length Sanistand
Scale 110DetailsW626Vde-V3 Back anchoring in UA profile W626Vde-H3 Back anchoring in UA profile Vertical section Horizontal section
Sanistand withconcealed mount cistern
SealantUD profile on insulation strips
UW runner
UW runner
Additional UA profile
Knauf multi-purpose screw FN
Uniflott + Trenn-Fix
UA profile
Knauf connection bracket withenclosed M8 carriage bolts
2x 125 mm DiamantDiamant screw XTB
Knauf connection bracket withenclosed M8 carriage bolts
Fixing bolts with nuts andwashers
Knauf sealing tape
Stud spacing le 625 mm
Additional UA profile
UA profile Fixing bolts with nutsand washers
Knauf connection bracket withenclosed M8 carriage bolts
Knauf connectionbracket with enclosedM8 carriage bolts
Notes
Max partition height at rear W112de UA 50 = 300 m UA 75 = see system data sheet W11de Knauf Metal Stud Partition for the wall heights
Minimum cladding front wall installations ge 18 mm Knauf Boards recommendation 2x 125 mm Knauf Diamant
Web cutouts are not permissible in UA Sanistand subject to cantilever loads point loads or linear distributed loadsObserve the manufacturersrsquo details for lateral UA profiles and cladding Additional UA profiles are required laterally on Sanistand mounts acc to DIN 18340 section 374 Only possible without additional UA profiles if the manufacturer of the Sanistand base or WC Sanistand permits itDeviating specifications of the Sanistand manufacturer must be considered and observed
20
Loads on partitions and furringsFull-length Sanistand
Scale 110DetailsW626Vde-V4 Back anchoring in mounting rail W626Vde-H4 Back anchoring in mounting rail Vertical section Horizontal section
Sanistand withconcealed mount cistern
2x 125 mm Diamant
SealantUD profile on insulation strips
UW runner
Diamant screw XTB
UA profile
Knauf multi-purpose screw FN
Mounting rail with fixing screw
Knauf connection bracket withenclosed M8 carriage bolt
Uniflott + Trenn-Fix
UA profile
Knauf connection bracket withenclosed M8 carriage bolt
Knauf sealing tapeUW runner
Stud spacing le 625 mm
UA profile
UA profile
Mounting railFixing screw
Mounting screw
Sanistand withconcealed mount cistern
Knauf connection bracket withenclosed M8 carriage bolt
Knauf connectionbracket with enclosedM8 carriage bolt
Notes
Max partition height rear W112de UA 50 = 300 m UA 75 = see system data sheet W11de Knauf Metal Stud Partitions for the wall heights
Minimum cladding front wall installations ge 18 mm Knauf Boards recommendation 2x 125 mm Knauf Diamant
Web cutouts are not permissible in UA Sanistand subject to cantilever loads point loads or linear distributed loadsObserve the manufacturersrsquo details for lateral UA profiles and cladding Additional UA profiles are required laterally on Sanistand mounts acc to DIN 18340 section 374 Only possible without additional UA profiles if the manufacturer of the Sanistand base or WC Sanistand permits itDeviating specifications of the Sanistand manufacturer must be considered and observed
21
Notes
In case of load attachment to ldquomulti-level ceiling systemsrdquo refer to the respective valid Knauf system data sheetsIn case of attachment of loads to free-spanning ceilings see system data sheet D13de Knauf Free-Spanning Ceilings
Attachment of loads to Knauf board ceilingsAdditional loads eg lighting fixtures curtain rails and similar can be fixed to Knauf board ceilings using universal dowels cavity dowels spring toggle dowels or Knauf Hartmut Hohlraumduumlbel cavity dowelsAdditional loads must be considered when determining the load class
NoteHeavy loads must be attached directly on load-bearing building elements (basic ceiling) or on auxiliary constructions eg traverses
For each area under load of the Knauf board ceiling the weight of thefastened components may not exceed the following limits
Permissible weight per ceiling area in kgmsup2Without fire resistance With fire resistance1)
15 61)Incaseofapplicationasafireresistanceceilingwithexposedceiling(multi-levelceilingsystem)15kgmsup2totalweightispermissiblefortheexposedceiling(includinginsulationlayerandattachedloads)attachedtothefireresistanceceiling
Furthermore the following conditions applyFor each anchoring point the components fastened to the board ceiling may not exceed the following weights
Fastening method Permissible weight per anchoring point in kgWithout fire resistance With fire resistance
Fastening in the cladding 6 05
Fastening to the grid 10 10
Fastening in the claddingKnauf Hartmut Hohlraumduumlbel cavity dowelScrew M5
Fastening to the gridKnauf Universalschraube FN multi-purpose screw eg curtain rail
The minimum separation spacings between individual attached loads must be observed to avoid local overloading of the ceiling The minimum separation clearance between two attachment points consists of both load radii for the point loadsThe load radius of a point load can be taken from the following diagram in dependence on the permissible weight per unit area for additional loads
Point load in kg
7570656055504540353025201510
0 2 3 4 5 6 7 8 9 10
Radiu
s in c
m
1
50
Fastening in the claddingpossible (without fire resistance)
3 kgmsup2 permissible additional weight (on the exposed ceiling under a fire resistance ceiling refer to the respective valid Knauf system data sheets)6 kgmsup2 permissible additional weight (with fire resistance)15 kgmsup2 permissible additional weight (without fire resistance)
Example fastening scheme at 15 kgmsup2
05 kg
10 kg
3 kgr = 25 cm
r = 46 cm
6 kgr = 355 cm
1 kg
r = 15 cm
r = 105 cm
NoteThe anchored loads can be transferred using several anchoring elements
Loads on board ceilingsFastening in the cladding grid
22
Knauf multi-purpose traversesThe multi-purpose traverse in Knauf board ceilings is suitable for the application of point loads up to 075 kN eg chandeliers music speakers or similarThe multi-purpose traverse consists of a 23 mm thick multi-layer wooden board and galvanized sheet metal profiles It is fastened to the side of the CD furring channelThe attachment of the loads to the traverses should be performed using Knauf Multi-Purpose Screw FNInstallation is possible in a double layer profile grid and flush profile grid
Installation and applicationBend the Daisy chain clip before lateral screw fastening The Daisy chain clip is then Z shaped The unpunched metal side of the Daisy chain clip is pushed onto the lower side of the traverse and then screw fastened laterally through the factory-made hole on the long side of the traverse Screw fasten 4x Daisy chain clips each using one drywall screw TN 35 x 35 about 100 mm from the corner of the multi-layer board on the long edge of the multi-purpose traverse Arrange an additional CD channel (length ge 650 mm) for every long edge in accordance with the width of the multi-purpose traverse Alternately a ceiling furring channel can be used for application of the multi-purpose traverse The supporting profiles are suspended using ceiling suspenders of load class 40 kg The suspenders may not be situated in the direct vicinity of the longitudinal area of the traverse as this will hinder the installation of the traverse Introduce the multi-purpose traverse between the support profiles bend the Daisy chain clip around the CD channel and engage it In case of single-layer cladding do not screw fasten the surface cladding with the multi-purpose traverse
1 Apply the Daisy chain clip 2 Bend the Daisy chain clip 3 Screw fasten the Daisy chain clip
Loads on board ceilingsAnchoring in the traverses
100 mm
23
Loads on board ceilingsAnchoring in the traverses
Scale 110 I Dimensions in mmDetailsD112de SO18 Vertical section ndash Multi-purpose traverse D113de SO12 Vertical section ndash Multi-purpose traverseeg with two additional CD channels I Without fire resistance eg with one additional CD channel I Without fire resistance
D112de SO19 Vertical section ndash Multi-purpose traverse D113de SO13 Vertical section ndash Multi-purpose traverseeg with two additional CD channels I Without fire resistance eg with one additional CD channel I Without fire resistance
D112de SO20 Top view ndash Multi-purpose traverse D113de SO14 Top view ndash Multi-purpose traverseeg with two additional CD channels I Without fire resistance eg with one additional CD channel I Without fire resistance
Fasten Daisy chain clip with drywall screwTN 35 x 35 to multi-purpose traverse
Additional CD channel with two suspendersLoad bearing capacity class ge 040 kN
Multi-purposetraverse555 300 23 mm
300
Furring channel spacing 500
Fasten Daisy chain clip with drywall screwTN 35 x 35 to multi-purpose traverse
Additional suspended load bearing capacity class ge 040 kNMulti-purposetraverse555 300 23 mm
300
Furring channel spacing 500
Additional CD channel with two suspendersLoad bearing capacity class ge 040 kN
Multi-purposetraverse555 300 23 mm
Fasten Daisy chain clip with drywall screwTN 35 x 35 to multi-purpose traverse
Wood panel 555approx
100
Additional suspenderload bearing capacityclass ge 040 kN
Multi-purposetraverse555 300 23 mm
Fasten Daisy chain clip with drywall screwTN 35 x 35 to multi-purpose traverse
Wood panel 555approx
100
Daisy chain clip
Furring channel spacing 500
Traverse
CDchannel
Multi-layerwood panel
Furring channel spacing 500
Multi-purposetraverse
Daisy chain clip
Multi-layerwood panel
Additional grid 4 additional suspension points (eg Nonius suspension)
All technical changes reserved Only the current printed instructions are valid The stated information represents current state-of-the-art Knauf technology The entire state of approved engineering rules appropriate standards guidelines and rules of crafts-manship are not included herewith These and all application instructions have to be adhered to separately by the installer Our warranty is expressly limited to our products in flawless condition All application quantities and delivery amounts are based on empirical data that are not easily transferable to other deviating areasAll rights reserved All amendments reprints and photocopies including those of excerpts require our expressed permission
The stated constructional and structural design specifications and characteristics of building physics of Knauf systems can only be ensured with the exclusive use of Knauf system components or other products expressly recommended by Knauf
Knauf Gips KG Am Bahnhof 7 97346 Iphofen GermanyKnauf DirectTechnical Advisory Service
knauf-direktknaufde
wwwknaufde
VT03deeng09190TI
The iPad App Knauf Infothek now provides all the current information and documents from Knauf Gips KG at any time and in every location in a clear and comfortable wayKnauf Infothek
Videos for Knauf systems and products can be found under the following linkwwwyoutubecomknaufEPD
2
Usage instructionsNotes on the documentKnauf technical information documents are the planning and application basis for planners and professional installers with the application of Knauf systems The contained information and specifications constructions details and stated products are based unless otherwise stated on the certificates of usability (eg National Technical Test Certificate (abP) andor German National Technical Approvals (abZ)) valid at the date they are published as well as on the applicable standards In addition design and structural requirements and those regarding building physics (fire protection and sound insulation) are considered The contained construction details are examples and can be used in a similar way for various cladding variants of the respective system At the same time the demands made on fire resistance andor sound insulation as well as any necessary additional measures andor limitations must be observed
References to other documents Metal stud partitions see system data sheet W11de Knauf Metal Stud Partitions
Wood frame partitions see system data sheet W12de Knauf Wood Frame Partitions
Fire walls see system data sheet W13de Knauf Fire Walls Furring and linings see system data sheet W61de Knauf Furring and Linings Metal Stud Partitions AQUAPANELreg see system data sheet W38de Knauf Metal Stud Partitions AQUAPANELreg
Board Ceilings ndash suspended under solid ceilings see system data sheet D11de Knauf Board Ceilings
ContentsUsage instructions 2Intended use of Knauf Systems 2
Loads on partitions and furringsIntroduction 3Cantilever loads 4
Rating diagrams 4Fastening in the cladding 6
Fields of application 6Fixing loads 6Rating 7
Anchoring in the traverses 8Fields of application 8Fixing loads 8Rating 9Knauf multi-purpose traverses 10Knauf steel anchoring traverse with gypsum fibre insert 12Knauf steel anchoring traverse 14
Full-length Sanistand 15
Loads on board ceilingsFastening in the cladding grid 21Anchoring in the traverses 22
Knauf multi-purpose traverses 22
Board ceilings under wood joist ceilings see system data sheet D15de Knauf wood joist ceiling systems
Observe the product data sheets of the individual Knauf system components
Intended use of Knauf SystemsPlease observe the following
Caution
Knauf systems may only be used for the application cases as stated in the Knauf documentation In case third-party products or components are used they must be recommended or approved by Knauf Flawless application of productssystems assumes proper transport storage assembly installation and maintenance
3
Loads on partitions and furringsIntroduction
Loads on partitions and furringsPartitions and furrings as drywall constructions are mainly non-load bearing constructions in keeping with the DIN EN 1991 standard The excellent performance of the Knauf partitions in combination with additional measures such as installed traverses or metal laminated hard gypsum boards offers solutions for the implementation of constructional challengesThis technical information document contains recommendations for the fastening and fixing of loads on partitions and furrings in the form of
Cantilever loads from static superimposed loads (cabinets shelves heating elements)
Dynamic loads such as handrails folding handles and fold-down seats acc to DIN 18 040 Construction of accessible buildings
Attachment of the WC bidet and washbasin using sanitary mounts in metal stud partitions
Normative definition of the loads on lightweight partitions are defined for example in the DIN 4103 DIN 18183 as well as in acc to Code of Practice No 8 of the Bundesverband der Gipsindustrie eV German Gypsum AssociationCantilever loads as described in the DIN 4103 are considered to be permanent loads and apply for example to cabinetsDynamic loads result from folding handles and fold-down seats Dynamic loads are recurring loads effective for a short duration and are time-dependentFor folding handles a projection of 80 cm with a load of 100 kN is assumed for the following recommendations Fold-down seats are considered as a maximum load of 150 kN with a projection of 48 cm Sanistands are offered by different manufacturers and are described normatively depending on the application whether toilet pans or washbasins The fracture load for toilet pans acc to the EN 997 stipulates 400 kN and for washbasins acc to EN 14688 a load of 150 kN is stipulatedThe Knauf partition systems in the following have been examined for the case above and determined to be appropriate for the load
Note
Fasteners in acc to DIN 4103 section 515 are to be used The details contained in this technical information document have been tested in the course of mechanical tests by Knauf
Differentiation cantilever load fixing loadTwo aspects must be considered in the attachment of loads on partitions and furrings
Cantilever loads
F F F F F F F
F
FFF
F F F
The cantilever load acts as a linear distributed load on the entire wallpartition system ie the entire wall system must be specifically designed for the purpose and the load must be transferred to the supporting structure without permitting a structural failure or deformation which exceed the limits of serviceability
Fixing loads
FF
The fastening of cantilever loads to partition systems are undertaken over several anchoring points which must be considered separately with respect to their loadbearing capacity in dependence on the selected fasteneranchor and the cladding as well as the substrate (cladding profile traverse)
Knauf system benefits Regulated construction High crack resistance with coordinated gypsum board types Diamant Steel GKFI as a surface traverse for flexible attachment in the entire wall area even with subsequent installation
4
Loads on partitions and furringsCantilever loads
Rating diagrams
Cabinet widthCabinet depth
Cabin
et he
ight
ge 30
0 mm
le 600 mmle 1200 mm
Eccentricityle 300 mm
The specified permissible cantilever loads are in accordance with the DIN 18183 or DIN 4103-1 at an eccentricity (spacing of load resulting to the wall surface) of max 300 mm The permissible load is reduced accordingly with greater eccentricity The following tables and diagrams are intended as an aid in the determination of the permissible cantilever loads with divergent eccentricity The values can be taken either from the tables or the diagrams
Up to 04 kNm (40 kgm) wall lengthMaximum permissible cabinet weight (kg) acc to table
Cabinet widthmm
Cabinet depthmm100 200 300 400 500 600
400 31 28 25 22 19 16600 465 42 375 33 285 24800 62 56 50 44 38 321000 775 70 625 55 475 401200 93 84 75 66 57 48
Assume the worst-case value with intermediate values or diagram procedure
orMaximum permissible cabinet weight (kg) acc to diagram
10
70
60
40
20
100
80
90
50
Cabinet depthmm 100 200 300 400 500 600
1000 800 600 400
30
Max permissible cabinet weight
kg
Cabinet width
mm1200
Up to 07 kNm (70 kgm) wall length Maximum permissible cabinet weight (kg) acc to table
Cabinet widthmm
Cabinet depthmm100 200 300 400 500 600
400 43 40 37 34 31 28600 645 60 555 51 465 42800 86 80 74 68 62 561000 1075 100 925 85 775 701200 129 120 111 102 93 84
Assume the worst-case value with intermediate values or diagram procedure
orMaximum permissible cabinet weight (kg) acc to diagram
kg
Max permissible cabinet weight
Cabinet width
mm1200
1000
400
600
800
mmCabinet depth
600100 200 300 400 500
10
70
60
40
20
30
100
80
90
110
120
50
5
Loads on partitions and furringsCantilever loads
Up to 10 kNm (100 kgm) wall lengthMaximum permissible cabinet weight (kg) acc to table
Cabinet widthmm
Cabinet depthmm100 200 300 400 500 600
400 90 80 70 60 50 40600 135 120 105 90 75 60800 180 160 140 120 100 801000 225 200 175 150 125 1001200 270 240 210 180 150 120
Assume the worst-case value with intermediate values or diagram procedure
orMaximum permissible cabinet weight (kg) acc to diagramMax permissible cabinet weight
kgCabinet width
mm1200
400
1000
600
800
Cabinet depthmm 600100 200 300 400 500
20
140
120
80
40
60
200
160
180
100
240
220
260
280
300
Up to 15 kNm (150 kgm) wall lengthMaximum permissible cabinet weight (kg) acc to table
Cabinet widthmm
Cabinet depthmm100 200 300 400 500 600
400 135 120 105 90 75 60600 202 180 157 135 112 90800 270 240 210 180 150 1201000 337 300 262 225 187 1501200 360 360 315 270 225 180
Assume the worst-case value with intermediate values or diagram procedure
orMaximum permissible cabinet weight (kg) acc to diagram
400
mm
1000
1200
600
800
Max permissible cabinet weight
kgCabinet width
Cabinet depthmm 600500400300200100
20
140
120
80
40
60
200
160
180
100
240
220
260
280
300
320
340
6
Loads on partitions and furringsFastening in the cladding
Fields of applicationAccording to DIN 18183 the metal stud partitions and independent furrings can be loaded at any position by cantilever loads
Up to 04 kNm (40 kgm) wall length Cladding thickness ge 125 mm Knauf boards Up to 07 kNm (70 kgm) wall length Cladding thickness ge 15 mm Diamant (in acc to abP P-140592810) ge 18 mm Knauf boards
With Diamant Steel GKFI and a cover layer ge 125 mm Diamant GKFI (see following table) cantilever loads up to 15 kNm (150 kgm) on walls are possible
Selection of the grid in dependence on the expected loadLoad max Load
typeProfile min Cladding thickness min Furring
possibleLoaded side Unloaded sideKn
auf
Boar
ds
Diam
ant
Diam
ant
Stee
l GKF
I Minimum thickness
Knau
f Bo
ards
Diam
ant
Diam
ant
Stee
l GKF
I Minimum thickness
tmm
tmmkNm2
04 StaticCW 50 125 125 YesCW 50 125 125 Yes
07 StaticCW 50 125 + 04 125 + 04 Yes 2)
CW 75 18 18 Yes 2)
CW 75 15 15 Yes 2)
10 StaticCW 50
125 + 041) + 125 2x 125 Yes
CW 75 125 + 04 125 No
15 Static CW 75 125 + 04
+ 125 2x 125 No
1)ScrewspacingDrywallScrewsXTB1stlayerDiamantSteelGKFIle250mm2)IncaseofapplicationofpartitionheightsacctoDIN18183-1onlycantileverloadsupto04kNmarepossible
Fixing loadsFor fixing of cantilever loads
Dowel screw Maximum screw dowel load capacity in kgX-hooks Knauf Cavity Dowel
HartmutScrew M5
fischer MHD 5 x 65 SScrew M5 or M6
Knauf Multi-Purpose Screw FN 43 x 65
Plastic cavity dowelOslash 8 or 10 mm
Diamant125 mm 5 10 15 40 20 13 3015 18 mm 5 10 15 45 25 14 352x 125 mm 5 10 15 60 30 20 45ge 2x 125 mm 5 10 15 65 35 40 50Diamant Steel GKFI1x 125 + 04 mm 5 10 15 80 50 30 30 3)
2x 125 + 04 mm 5 10 15 100 90 60 55 3)
Measuredwith300mmeccentricity3)ValuesapplywithfischerplasticcavitydowelsUX8x50withKnaufMulti-PurposeScrewFN43x65orequivalent
Notes
Static loads in this respect are permanently fastened loads such as towel rails cabinets shelves and boilers Dynamic loads are exerted by fastened components which are subjected to continuous changes in load such as handrails fold-down seats and folding handles The use of traverses is required here see page 8Always screw fasten Diamant Steel GKFI with Diamant Screws XTB even for a cover layer of Diamant
7
Loads on partitions and furringsAnchoring in the cladding
RatingThe specified permissible cantilever loads are in accordance with the DIN 18183 or DIN 4103-1 at an eccentricity (spacing of resulting load to the wall surface) of max 300 mm The permissible load is reduced accordingly with greater eccentricity The determination of the permissible cantilever loads with divergent eccentricity is undertaken using the tables or diagrams on page 4 and page 5
Rating examples Determination of the permissible cabinet weight as well as the required minimum number of dowels (always ge 2)Metal stud partition W111de CW 50 cladding 125 mm Diamant GKFI acc to tableField of application static load max cantilever load 04 kNm (40 kgm) wall length Cabinet
widthCabinet depthmm
mm 100 200 300 400 500 600
400 31 28 25 22 19 16
600 465 42 375 33 285 24
800 62 56 50 44 38 32
1000 775 70 625 55 475 40
1200 93 84 75 66 57 48
Cabinet depth 400 mm cabinet width 1000 mm Max cabinet weight 55 kg
Cladding thickness 125 mm plastic cavity dowel
Max dowel load 30 kg
Required number of dowels 55 kg 30 kg = 18 2 dowels
are the min necessary
Metal stud partition W111de CW 75 cladding 2x 125 mm Diamant GKFI acc to diagramField of application static load max cantilever load 07 kNm (70 kgm) wall length
400
mm12001000
600
100 200 400 500 600mm
10
70
60
40
20 30
kg
100
80 90
110120
800
300
50
1
23
450
65
Cabinet depth
Cabinet width
Max permissible cabinet weightCabinet depth 450 mm cabinet width 800 mm
With cabinet depth 450 mm 1 vertically upwards up to the cabinet width line 800 mm
2 at the intersection point horizontal to the left ndash read off value 3
Max cabinet weight 65 kg
Cladding thickness 2x 125 mm Knauf Cavity Dowel Hartmut
Max dowel load 60 kg
Required number of dowels 65 kg 60 kg = 108 2 dowels
are the min necessary
8
Fields of applicationTraverses are built-in elements in lightweight partitions that transfer the fastening loads directly into the grid or into the flanking solid constructions
Selection of the traverse and grid in dependence on the expected loadFastening Load max Load type Profile min Cladding thickness min Independent
furring possible
Knauf Boards DiamantkNm2 mm mm
Steel anchoring traversesee page 14
07 Static CW 50 125 125 No07 Static CW 50 18 15 Yes10 Static CW 75 125 125 No10 Static CW 50 18 15 Yes
Metal traverse with gypsum fibre insertsee page 12
07 Static CW 50 125 125 No07 Static CW 50 18 15 Yes10 Static CW 75 125 125 No10 Static CW 50 18 15 Yes15 Static CW 50 18 15 No15 Static UA 50 18 15 Yes15 Dynamic UA 75 18 15 Yes
Multi-purpose traversesee page 10
07 Static CW 50 125 125 No07 Static CW 50 18 15 Yes10 Static CW 75 125 125 No10 Static CW 50 18 15 Yes15 Static CW 50 18 15 No15 Static UA 50 18 15 Yes15 Dynamic UA 75 18 15 Yes
Fixing loadsFor fixing of cantilever loads
Dowel screw Maximum screw dowel load capacity in kgKnauf Cavity Dowel Hartmut
fischer MHD 5 x 65 S
Knauf Multi- Purpose Screw FN 43 x 65
fischer plastic cavity dowels 8 x 50 with Knauf Multi-Purpose Screw FN 43 x 65
Wood screw Oslash 50 mm
Wood screw Oslash 60 mm
TraversesSteel anchoring traverse 75 ndash 45 40 45 45
Metal traversewith gypsum fibre insert
90 75 65 46 55 70
Multi-purpose traverse ndash ndash 125 ndash 115 165
Measuredwith300mmeccentricity
Loads on partitions and furringsAnchoring in the traverses
NotesStatic loads in this respect are permanently fastened loads such as towel rails cabinets shelves and boilers Dynamic loads are exerted by fastened components which are subjected to continuous changes in load such as handrails fold-down seats and folding handles
9
Loads on partitions and furringsAnchoring in the traverses
RatingThe specified permissible cantilever loads are in accordance with the DIN 18183 or DIN 4103-1 at an eccentricity (spacing of resulting load to the wall surface) of max 300 mm The permissible load is reduced accordingly with greater eccentricity The determination of the permissible cantilever loads with divergent eccentricity is undertaken using the tables or diagrams on page 4 and page 5
Rating examples Determination of the permissible cabinet weight as well as the required minimum number of dowels (always ge 2)Metal stud partition W111de CW 50 cladding 18 mm Knauf board acc to tableField of application static load max cantilever load 07 kNm (70 kgm) wall length Cabinet
widthCabinet depthmm
mm 100 200 300 400 500 600400 43 40 37 34 31 28600 645 60 555 51 465 42800 86 80 74 68 62 561000 1075 100 925 85 775 701200 129 120 111 102 93 84
Cabinet depth 500 mm cabinet width 800 mm Max cabinet weight 62 kg Fixing traverse Knauf Multi-Purpose Screw FN 43 x 65
Max screw load 45 kg
Required number of screws 62 kg 45 kg = 14 2 screws
are the min necessary
Metal stud partition W111de UA 75 cladding 15 mm Diamant GKFI acc to diagram
Field of application dynamic load max cantilever load 15 kNm (150 kgm) wall length
20
400
Cabinet depth100 200 600
Max permissible cabinet weight
140120
80
4060
kg
200
160
180
Cabinet width
mm
1000
1200
600
mm 300
100 800
240220
260280300320340
450400 500
165
1
23
Cabinet depth 450 mm cabinet width 800 mm
With cabinet depth 450 mm 1 vertically upwards up to the cabinet width line 800 mm
2 at the intersection point horizontal to the left read off value 3
Max cabinet weight 165 kg
Multi-purpose traverse Knauf Multi-Purpose Screw FN 43 x 65
Max screw load 125 kg
Required number of screws 165 kg 125 kg = 13 2 screws
are the min necessary
10
Knauf multi-purpose traversesThe multi-purpose traverse is suitable for accepting loads attached to the wall up to 15 kNm wall length eg cupboards boilers folding wall attached seats folding handles and similarThe multi-purpose traverse consists of a 23 mm thick multi-layer wooden board and galvanized sheet metal profiles It is fastened to the side of the floor-to-ceiling profilesThe attachment of the loads to the traverses should be performed using Knauf Multi-Purpose Screw FN
NoteTraverses for installation in damp and wet rooms see also system data sheet W38de Knauf Metal Stud Partitions AQUAPANELreg
Loads on partitions and furringsAnchoring in the traverses
Installation and applicationMulti-purpose traverse made of multi-layer wooden board and galvanized sheet metal profiles attached to the side of the CW studs UA profiles For CW studs screw fasten using the 6 enclosed Metal Screws LN 35 x 11 mm (3 per side) For UA profiles screw fasten with the 6 enclosed Drilling Screws ST 42 x 13 mm (3 per side)Arrangement in a rowUA profiles CW studs
Direction of installation Direction of installation
11
Loads on partitions and furringsAnchoring in the traverses
W234de-A10 View ndash Design with UA profile W234de-A13 View ndash Design with CW stud
W234de-H10 Horizontal section ndash Design with UA profile W234de-H13 Horizontal section ndash Design with CW studeg W626de eg W626de
W234de-V10 Vertical section ndash Design with UA profile W234de-V13 Vertical section ndash Design with CW studeg W116de eg W112de
Wooden board 555
Stud spacing 625 (grid dimension)
300
Multi-purpose traverse555 300 23 mm
Multi-layer wooden board
UA profile
Drillingscrew ST42 x 13(enclosed)
Wooden board 555
Stud spacing 625 (grid dimension)
300 Metal screw
LN 35 x 11(enclosed)
Multi-purpose traverse555 300 23 mm
Multi-layer wooden board
CW stud
Wooden board 555
Stud spacing 625 (grid dimension)
300
Multi-purpose traverse555 300 23 mm
UA profileDrilling screwST 42 x 13
Multi-purpose traverse555 300 23 mm
CW studMetal screwLN 35 x 11
48
eg folding wallattached seat
Knauf boardstrips
eg Supporthandle maxprojection 800 mm
Multi-purposetraverseUA profileKnauf boards
48
Multi-purposetraverseCW studKnauf boards
eg Cabinet
Scale 110 I Dimensions in mmDetails
Note No web cutouts in the CW studs are permissible for traverses to which the CW studs are attached
12
Knauf steel anchoring traverse with gypsum fibre insertThe steel anchoring traverse with gypsum fibre insert is suitable for accepting loads attached to the wall up to 15 kNm wall length eg cupboards shelves handrails and similarThe metal traverse with gypsum fibre insert consists of 075 mm thick sheet metal as well as an 18 mm thick gypsum fibre board It is fastened to the side of the floor-to-ceiling profiles The attachment of the loads to the traverses should be performed using Knauf Multi-Purpose Screw FNUse in partition systems where the requirement for non-combustible reaction to fire exists
Installation and applicationSteel anchoring traverse made of galvanized steel with gypsum fibre insert fastened to the CW studs UA profiles In case of CW studs crimp using a Stud Crimper and for UA profiles screw fasten with 6 Drilling screws LB 35 x 16 mmArrangement in a rowUA profiles CW studs
Loads on partitions and furringsAnchoring in the traverses
13
Scale 110 I Dimensions in mmDetailsW234de-A12 View - Design with UA profile W234de-A14 View - Design with CW stud
W234de-H12 Horizontal section - Design with UA profile W234de-H14 Horizontal section - Design with CW studeg W112de eg W112de
W234de-V12 Vertical section - Design with UA profile W234de-V14 Vertical section - Design with CW studeg W112de eg W112de
Traverse dimension 620
Stud spacing 625 (grid dimension)
290
Steel anchoring traversewith gypsum fibre insert
Traverse attached to UA profileusing drilling screws
UA profile
Steel anchoring traversewith gypsum fibre insert
CW stud
Crimp the traverse to the CW studusing a stud crimper
Traverse dimension 620
Stud spacing 625 (grid dimension)
290
Drilling screwLB 35 x 16
Steel anchoringtraverse with gypsum
fibre insert
UA profile Crimped Steel anchoring traversewith gypsum fibre insert
CW stud
eg Handrail
UA profileKnauf boards
Steel anchoring traversewith gypsum fibre insert
eg Handrail
CW studKnauf board
Steel anchoring traversewith gypsum fibre insert
Loads on partitions and furringsAnchoring in the traverses
Note No web cutouts in the CW studs are permissible for traverses to which the CW studs are attached
14
Loads on partitions and furringsAnchoring in the traverses
Knauf steel anchoring traverseThe steel anchoring traverse is suitable for accepting loads attached to the wall up to 10 kNm wall length eg towel holders cupboards shelves and similar Not suitable for dynamic loads such as folding wall attached seatsThe steel anchoring traverse consists of 075 mm thick sheet metal and are crimped onto the side using a stud crimper on the CW studs Particularly suitable for single-layer clad metal stud partitions and furrings where in case of cantilever loads gt 04 kNm (400 kgm) wall length the installation of a traverse is required
NoteTraverses for installation in damp and wet rooms see also system data sheet W38de Knauf Metal Stud Partitions AQUAPANELreg
Installation and applicationCrimp the steel anchoring traverse made of galvanized sheet steel to the CW studs using a Stud CrimperAdditional screw fastening of the steel anchoring traverse via screw fastening of the cladding (min 2 to 3 anchoring points) Reduce the screw spacing of the cladding if necessaryArrangement in a rowCW studs
Scale 110 I Dimensions in mmDetailsW234de-A11 View W234de V11 Vertical section
eg W111de
W234de-H11 Horizontal sectioneg W111de
Sheet metal gauge 075 mm
Steel anchoring traverse
CW stud
Crimp the traverse to the CW studusing the stud crimper
290
Traverse dimension 620
Stud spacing 625 (grid dimension)
eg Cabinet
CW stud
Knauf boardSteel anchoring traverse
Steel anchoring traverseCW stud
Crimped
Note No web cutouts in the CW studs are permissible for traverses to which the CW studs are attached
15
Full-length SanistandFloor-to-ceiling Sanistands made of galvanized UA profiles (min UA 75) 2 mm thick are suitable for transferring loads from traverses into the supporting structure or for fixing loads hanging onto walls such as school blackboards up to 15 kNm wall lengthFloor-to-ceiling Sanistands profiles are anchored to the basic floor and ceiling with door frame brackets or connection brackets for UA profiles The upper door frame bracket includes openings for routing cables such as pipe-in-pipe systems or electrical cablesThe loads are connected directly to the flange of the UA profile
W228de-A10 View
le 1000 mm
UW runnercontinuous
Door frameconnection brackettop connection withenclosed dowels
CW studAxial spacing suitedto partition system
UA profileas afloor-to-ceilingSanistand forbearing cantileverloads
UW runnercontinuous
Door frameconnection bracketbottom connectionwith enclosed dowels
Scale 110
Installation and applicationFloor-to-ceiling Sanistands made of UA profiles must be anchored to the basic floor and ceiling with door frame brackets or connection brackets for UA profiles The upper door frame bracket includes openings for routing cables such as pipe-in-pipe systems or electrical cables Fasten objects to UA profiles using threaded rods U washers and M1012 steel nuts or self-tapping screws
Loads on partitions and furringsFull-length Sanistand
Detail
Notes
Web cutouts are not permissible in UA Sanistand subject to cantilever loads point loads or linear distributed loadsMaximum screw load with connections to full height Sanistand (UA profile)Every UA profile flange and anchoring point may not exceed a resulting pull-out load of 150 kN (150 kg)Components similar to cantilevers such as foldable rails should be screwed onto two adjacent UA profilesUse suitable drilling screws eg Ejot Zebra Piasta Hilti S-MD or comparable
16
Loads on partitions and furringsFull-length Sanistand
Scale 110DetailsW116de-V1 Sanistand W116de-H1 SanistandVertical section I Without fire resistance Horizontal section I Without fire resistance
UW runnerUniflott + Trenn-Fix
UW runner
Additional UA profile
Sanistand withconcealed mount cistern
Knauf connectionbracket with enclosedM8 carriage bolts
Knauf conection bracket withenclosed M8 carriage bolt
2x 125 mm DiamantDiamant screw XTB
Additional CW stud
Knauf sealing tape
Board strip installationacc to W11de systemdata sheet
Stud spacing le 625 mm
CW stud profile
Additional CW studBoard strip installation in acc with W11de system data sheet
Knauf connection bracket withenclosed M8 carriage bolts
Additional UA profileSanitand with concealedmount cistern
Notes
Max partition height UA 50 = 300 m UA 75 = see system data sheet W11de Knauf Metal Stud Partition for the wall heights
Minimum cladding ge 18 mm Knauf Boards recommendation 2x 125 mm Knauf Diamant
Web cutouts are not permissible in UA Sanistand subject to cantilever loads point loads or linear distributed loadsObserve the manufacturersrsquo details for lateral UA profiles and cladding Additional UA profiles are required laterally on Sanistand mounts acc to DIN 18340 section 374 Only possible without additional UA profiles if the manufacturer of the Sanistand base or WC Sanistand permits itDeviating specifications of the Sanistand manufacturer must be considered and observed
17
Loads on partitions and furringsFull-length Sanistand
Notes
Max partition height rear W112de UA 50 = 300 m UA 75 = see system data sheet W11de Knauf Metal Stud Partition for the wall heights
Minimum cladding front wall installations ge 18 mm Knauf Boards recommendation 2x 125 mm Knauf Diamant
Web cutouts are not permissible in UA Sanistand subject to cantilever loads point loads or linear distributed loadsObserve the manufacturersrsquo details for lateral UA profiles and cladding Additional UA profiles are required laterally on Sanistand mounts acc to DIN 18340 section 374 Only possible without additional UA profiles if the manufacturer of the Sanistand base or WC Sanistand permits itDeviating specifications of the Sanistand manufacturer must be considered and observed
Scale 110DetailsW626Vde-V1 Without back anchoring W626Vde-H1 Without back anchoring Vertical section Horizontal section
UW runnerUniflott + Trenn-Fix
UW runner
Additional UA profile
Sanistand withconcealed mount cistern
Knauf connection bracket withenclosed M8 carriage bolt
Knauf connection bracket withenclosed M8 carriage bolt
2x 125 mm DiamantDiamant screw XTB
Knauf sealing tape
Sanistand withconcealed mount cisternKnauf connection bracket with
enclosed M8 carriage bolts
Stud spacing le 625 mm
UW runner
Knauf boardsCW stud
Additional UA profile
18
Loads on partitions and furringsFull-length Sanistand
Scale 110DetailsW626Vde-V2 Back anchoring in traverse W626Vde-H2 Back anchoring in traverse Vertical section Horizontal section
Sanistand withconcealed mount cistern
SealantUD profile made of insulation strips
UW runner
UW runner
UA profile
Knauf multi-purpose screw FN
Uniflott + Trenn-Fix
Multi-purpose traverse 555 300 23 mm
Knauf connection bracket withenclosed M8 carriage bolts
2x 125 mm DiamantDiamant screw XTB
Knauf connection bracket withenclosed M8 carriage bolt
Wall anchor installation acc to WCSanistand manufacturer specifications
Knauf sealing tape
Stud spacing le 625 mm
Multi-purpose traverse555 300 23 mm
UA profile
UA profile
Knauf connection bracket withenclosed M8 carriage bolt
Knauf connectionbracket with enclosedM8 carriage bolt
Wall anchorinstallation acc to
WC Sanistandmanufacturerspecifications
Notes
Max partition height rear W112de UA 50 = 300 m UA 75 = see system data sheet W11de Knauf Metal Stud Partitions for the wall heights
Minimum cladding front wall installations ge 18 mm Knauf Boards recommendation 2x 125 mm Knauf Diamant
Web cutouts are not permissible in UA Sanistand subject to cantilever loads point loads or linear distributed loadsObserve the manufacturersrsquo details for lateral UA profiles and cladding Additional UA profiles are required laterally on Sanistand mounts acc to DIN 18340 section 374 Only possible without additional UA profiles if the manufacturer of the Sanistand base or WC Sanistand permits itDeviating specifications of the Sanistand manufacturer must be considered and observed
19
Loads on partitions and furringsFull-length Sanistand
Scale 110DetailsW626Vde-V3 Back anchoring in UA profile W626Vde-H3 Back anchoring in UA profile Vertical section Horizontal section
Sanistand withconcealed mount cistern
SealantUD profile on insulation strips
UW runner
UW runner
Additional UA profile
Knauf multi-purpose screw FN
Uniflott + Trenn-Fix
UA profile
Knauf connection bracket withenclosed M8 carriage bolts
2x 125 mm DiamantDiamant screw XTB
Knauf connection bracket withenclosed M8 carriage bolts
Fixing bolts with nuts andwashers
Knauf sealing tape
Stud spacing le 625 mm
Additional UA profile
UA profile Fixing bolts with nutsand washers
Knauf connection bracket withenclosed M8 carriage bolts
Knauf connectionbracket with enclosedM8 carriage bolts
Notes
Max partition height at rear W112de UA 50 = 300 m UA 75 = see system data sheet W11de Knauf Metal Stud Partition for the wall heights
Minimum cladding front wall installations ge 18 mm Knauf Boards recommendation 2x 125 mm Knauf Diamant
Web cutouts are not permissible in UA Sanistand subject to cantilever loads point loads or linear distributed loadsObserve the manufacturersrsquo details for lateral UA profiles and cladding Additional UA profiles are required laterally on Sanistand mounts acc to DIN 18340 section 374 Only possible without additional UA profiles if the manufacturer of the Sanistand base or WC Sanistand permits itDeviating specifications of the Sanistand manufacturer must be considered and observed
20
Loads on partitions and furringsFull-length Sanistand
Scale 110DetailsW626Vde-V4 Back anchoring in mounting rail W626Vde-H4 Back anchoring in mounting rail Vertical section Horizontal section
Sanistand withconcealed mount cistern
2x 125 mm Diamant
SealantUD profile on insulation strips
UW runner
Diamant screw XTB
UA profile
Knauf multi-purpose screw FN
Mounting rail with fixing screw
Knauf connection bracket withenclosed M8 carriage bolt
Uniflott + Trenn-Fix
UA profile
Knauf connection bracket withenclosed M8 carriage bolt
Knauf sealing tapeUW runner
Stud spacing le 625 mm
UA profile
UA profile
Mounting railFixing screw
Mounting screw
Sanistand withconcealed mount cistern
Knauf connection bracket withenclosed M8 carriage bolt
Knauf connectionbracket with enclosedM8 carriage bolt
Notes
Max partition height rear W112de UA 50 = 300 m UA 75 = see system data sheet W11de Knauf Metal Stud Partitions for the wall heights
Minimum cladding front wall installations ge 18 mm Knauf Boards recommendation 2x 125 mm Knauf Diamant
Web cutouts are not permissible in UA Sanistand subject to cantilever loads point loads or linear distributed loadsObserve the manufacturersrsquo details for lateral UA profiles and cladding Additional UA profiles are required laterally on Sanistand mounts acc to DIN 18340 section 374 Only possible without additional UA profiles if the manufacturer of the Sanistand base or WC Sanistand permits itDeviating specifications of the Sanistand manufacturer must be considered and observed
21
Notes
In case of load attachment to ldquomulti-level ceiling systemsrdquo refer to the respective valid Knauf system data sheetsIn case of attachment of loads to free-spanning ceilings see system data sheet D13de Knauf Free-Spanning Ceilings
Attachment of loads to Knauf board ceilingsAdditional loads eg lighting fixtures curtain rails and similar can be fixed to Knauf board ceilings using universal dowels cavity dowels spring toggle dowels or Knauf Hartmut Hohlraumduumlbel cavity dowelsAdditional loads must be considered when determining the load class
NoteHeavy loads must be attached directly on load-bearing building elements (basic ceiling) or on auxiliary constructions eg traverses
For each area under load of the Knauf board ceiling the weight of thefastened components may not exceed the following limits
Permissible weight per ceiling area in kgmsup2Without fire resistance With fire resistance1)
15 61)Incaseofapplicationasafireresistanceceilingwithexposedceiling(multi-levelceilingsystem)15kgmsup2totalweightispermissiblefortheexposedceiling(includinginsulationlayerandattachedloads)attachedtothefireresistanceceiling
Furthermore the following conditions applyFor each anchoring point the components fastened to the board ceiling may not exceed the following weights
Fastening method Permissible weight per anchoring point in kgWithout fire resistance With fire resistance
Fastening in the cladding 6 05
Fastening to the grid 10 10
Fastening in the claddingKnauf Hartmut Hohlraumduumlbel cavity dowelScrew M5
Fastening to the gridKnauf Universalschraube FN multi-purpose screw eg curtain rail
The minimum separation spacings between individual attached loads must be observed to avoid local overloading of the ceiling The minimum separation clearance between two attachment points consists of both load radii for the point loadsThe load radius of a point load can be taken from the following diagram in dependence on the permissible weight per unit area for additional loads
Point load in kg
7570656055504540353025201510
0 2 3 4 5 6 7 8 9 10
Radiu
s in c
m
1
50
Fastening in the claddingpossible (without fire resistance)
3 kgmsup2 permissible additional weight (on the exposed ceiling under a fire resistance ceiling refer to the respective valid Knauf system data sheets)6 kgmsup2 permissible additional weight (with fire resistance)15 kgmsup2 permissible additional weight (without fire resistance)
Example fastening scheme at 15 kgmsup2
05 kg
10 kg
3 kgr = 25 cm
r = 46 cm
6 kgr = 355 cm
1 kg
r = 15 cm
r = 105 cm
NoteThe anchored loads can be transferred using several anchoring elements
Loads on board ceilingsFastening in the cladding grid
22
Knauf multi-purpose traversesThe multi-purpose traverse in Knauf board ceilings is suitable for the application of point loads up to 075 kN eg chandeliers music speakers or similarThe multi-purpose traverse consists of a 23 mm thick multi-layer wooden board and galvanized sheet metal profiles It is fastened to the side of the CD furring channelThe attachment of the loads to the traverses should be performed using Knauf Multi-Purpose Screw FNInstallation is possible in a double layer profile grid and flush profile grid
Installation and applicationBend the Daisy chain clip before lateral screw fastening The Daisy chain clip is then Z shaped The unpunched metal side of the Daisy chain clip is pushed onto the lower side of the traverse and then screw fastened laterally through the factory-made hole on the long side of the traverse Screw fasten 4x Daisy chain clips each using one drywall screw TN 35 x 35 about 100 mm from the corner of the multi-layer board on the long edge of the multi-purpose traverse Arrange an additional CD channel (length ge 650 mm) for every long edge in accordance with the width of the multi-purpose traverse Alternately a ceiling furring channel can be used for application of the multi-purpose traverse The supporting profiles are suspended using ceiling suspenders of load class 40 kg The suspenders may not be situated in the direct vicinity of the longitudinal area of the traverse as this will hinder the installation of the traverse Introduce the multi-purpose traverse between the support profiles bend the Daisy chain clip around the CD channel and engage it In case of single-layer cladding do not screw fasten the surface cladding with the multi-purpose traverse
1 Apply the Daisy chain clip 2 Bend the Daisy chain clip 3 Screw fasten the Daisy chain clip
Loads on board ceilingsAnchoring in the traverses
100 mm
23
Loads on board ceilingsAnchoring in the traverses
Scale 110 I Dimensions in mmDetailsD112de SO18 Vertical section ndash Multi-purpose traverse D113de SO12 Vertical section ndash Multi-purpose traverseeg with two additional CD channels I Without fire resistance eg with one additional CD channel I Without fire resistance
D112de SO19 Vertical section ndash Multi-purpose traverse D113de SO13 Vertical section ndash Multi-purpose traverseeg with two additional CD channels I Without fire resistance eg with one additional CD channel I Without fire resistance
D112de SO20 Top view ndash Multi-purpose traverse D113de SO14 Top view ndash Multi-purpose traverseeg with two additional CD channels I Without fire resistance eg with one additional CD channel I Without fire resistance
Fasten Daisy chain clip with drywall screwTN 35 x 35 to multi-purpose traverse
Additional CD channel with two suspendersLoad bearing capacity class ge 040 kN
Multi-purposetraverse555 300 23 mm
300
Furring channel spacing 500
Fasten Daisy chain clip with drywall screwTN 35 x 35 to multi-purpose traverse
Additional suspended load bearing capacity class ge 040 kNMulti-purposetraverse555 300 23 mm
300
Furring channel spacing 500
Additional CD channel with two suspendersLoad bearing capacity class ge 040 kN
Multi-purposetraverse555 300 23 mm
Fasten Daisy chain clip with drywall screwTN 35 x 35 to multi-purpose traverse
Wood panel 555approx
100
Additional suspenderload bearing capacityclass ge 040 kN
Multi-purposetraverse555 300 23 mm
Fasten Daisy chain clip with drywall screwTN 35 x 35 to multi-purpose traverse
Wood panel 555approx
100
Daisy chain clip
Furring channel spacing 500
Traverse
CDchannel
Multi-layerwood panel
Furring channel spacing 500
Multi-purposetraverse
Daisy chain clip
Multi-layerwood panel
Additional grid 4 additional suspension points (eg Nonius suspension)
All technical changes reserved Only the current printed instructions are valid The stated information represents current state-of-the-art Knauf technology The entire state of approved engineering rules appropriate standards guidelines and rules of crafts-manship are not included herewith These and all application instructions have to be adhered to separately by the installer Our warranty is expressly limited to our products in flawless condition All application quantities and delivery amounts are based on empirical data that are not easily transferable to other deviating areasAll rights reserved All amendments reprints and photocopies including those of excerpts require our expressed permission
The stated constructional and structural design specifications and characteristics of building physics of Knauf systems can only be ensured with the exclusive use of Knauf system components or other products expressly recommended by Knauf
Knauf Gips KG Am Bahnhof 7 97346 Iphofen GermanyKnauf DirectTechnical Advisory Service
knauf-direktknaufde
wwwknaufde
VT03deeng09190TI
The iPad App Knauf Infothek now provides all the current information and documents from Knauf Gips KG at any time and in every location in a clear and comfortable wayKnauf Infothek
Videos for Knauf systems and products can be found under the following linkwwwyoutubecomknaufEPD
3
Loads on partitions and furringsIntroduction
Loads on partitions and furringsPartitions and furrings as drywall constructions are mainly non-load bearing constructions in keeping with the DIN EN 1991 standard The excellent performance of the Knauf partitions in combination with additional measures such as installed traverses or metal laminated hard gypsum boards offers solutions for the implementation of constructional challengesThis technical information document contains recommendations for the fastening and fixing of loads on partitions and furrings in the form of
Cantilever loads from static superimposed loads (cabinets shelves heating elements)
Dynamic loads such as handrails folding handles and fold-down seats acc to DIN 18 040 Construction of accessible buildings
Attachment of the WC bidet and washbasin using sanitary mounts in metal stud partitions
Normative definition of the loads on lightweight partitions are defined for example in the DIN 4103 DIN 18183 as well as in acc to Code of Practice No 8 of the Bundesverband der Gipsindustrie eV German Gypsum AssociationCantilever loads as described in the DIN 4103 are considered to be permanent loads and apply for example to cabinetsDynamic loads result from folding handles and fold-down seats Dynamic loads are recurring loads effective for a short duration and are time-dependentFor folding handles a projection of 80 cm with a load of 100 kN is assumed for the following recommendations Fold-down seats are considered as a maximum load of 150 kN with a projection of 48 cm Sanistands are offered by different manufacturers and are described normatively depending on the application whether toilet pans or washbasins The fracture load for toilet pans acc to the EN 997 stipulates 400 kN and for washbasins acc to EN 14688 a load of 150 kN is stipulatedThe Knauf partition systems in the following have been examined for the case above and determined to be appropriate for the load
Note
Fasteners in acc to DIN 4103 section 515 are to be used The details contained in this technical information document have been tested in the course of mechanical tests by Knauf
Differentiation cantilever load fixing loadTwo aspects must be considered in the attachment of loads on partitions and furrings
Cantilever loads
F F F F F F F
F
FFF
F F F
The cantilever load acts as a linear distributed load on the entire wallpartition system ie the entire wall system must be specifically designed for the purpose and the load must be transferred to the supporting structure without permitting a structural failure or deformation which exceed the limits of serviceability
Fixing loads
FF
The fastening of cantilever loads to partition systems are undertaken over several anchoring points which must be considered separately with respect to their loadbearing capacity in dependence on the selected fasteneranchor and the cladding as well as the substrate (cladding profile traverse)
Knauf system benefits Regulated construction High crack resistance with coordinated gypsum board types Diamant Steel GKFI as a surface traverse for flexible attachment in the entire wall area even with subsequent installation
4
Loads on partitions and furringsCantilever loads
Rating diagrams
Cabinet widthCabinet depth
Cabin
et he
ight
ge 30
0 mm
le 600 mmle 1200 mm
Eccentricityle 300 mm
The specified permissible cantilever loads are in accordance with the DIN 18183 or DIN 4103-1 at an eccentricity (spacing of load resulting to the wall surface) of max 300 mm The permissible load is reduced accordingly with greater eccentricity The following tables and diagrams are intended as an aid in the determination of the permissible cantilever loads with divergent eccentricity The values can be taken either from the tables or the diagrams
Up to 04 kNm (40 kgm) wall lengthMaximum permissible cabinet weight (kg) acc to table
Cabinet widthmm
Cabinet depthmm100 200 300 400 500 600
400 31 28 25 22 19 16600 465 42 375 33 285 24800 62 56 50 44 38 321000 775 70 625 55 475 401200 93 84 75 66 57 48
Assume the worst-case value with intermediate values or diagram procedure
orMaximum permissible cabinet weight (kg) acc to diagram
10
70
60
40
20
100
80
90
50
Cabinet depthmm 100 200 300 400 500 600
1000 800 600 400
30
Max permissible cabinet weight
kg
Cabinet width
mm1200
Up to 07 kNm (70 kgm) wall length Maximum permissible cabinet weight (kg) acc to table
Cabinet widthmm
Cabinet depthmm100 200 300 400 500 600
400 43 40 37 34 31 28600 645 60 555 51 465 42800 86 80 74 68 62 561000 1075 100 925 85 775 701200 129 120 111 102 93 84
Assume the worst-case value with intermediate values or diagram procedure
orMaximum permissible cabinet weight (kg) acc to diagram
kg
Max permissible cabinet weight
Cabinet width
mm1200
1000
400
600
800
mmCabinet depth
600100 200 300 400 500
10
70
60
40
20
30
100
80
90
110
120
50
5
Loads on partitions and furringsCantilever loads
Up to 10 kNm (100 kgm) wall lengthMaximum permissible cabinet weight (kg) acc to table
Cabinet widthmm
Cabinet depthmm100 200 300 400 500 600
400 90 80 70 60 50 40600 135 120 105 90 75 60800 180 160 140 120 100 801000 225 200 175 150 125 1001200 270 240 210 180 150 120
Assume the worst-case value with intermediate values or diagram procedure
orMaximum permissible cabinet weight (kg) acc to diagramMax permissible cabinet weight
kgCabinet width
mm1200
400
1000
600
800
Cabinet depthmm 600100 200 300 400 500
20
140
120
80
40
60
200
160
180
100
240
220
260
280
300
Up to 15 kNm (150 kgm) wall lengthMaximum permissible cabinet weight (kg) acc to table
Cabinet widthmm
Cabinet depthmm100 200 300 400 500 600
400 135 120 105 90 75 60600 202 180 157 135 112 90800 270 240 210 180 150 1201000 337 300 262 225 187 1501200 360 360 315 270 225 180
Assume the worst-case value with intermediate values or diagram procedure
orMaximum permissible cabinet weight (kg) acc to diagram
400
mm
1000
1200
600
800
Max permissible cabinet weight
kgCabinet width
Cabinet depthmm 600500400300200100
20
140
120
80
40
60
200
160
180
100
240
220
260
280
300
320
340
6
Loads on partitions and furringsFastening in the cladding
Fields of applicationAccording to DIN 18183 the metal stud partitions and independent furrings can be loaded at any position by cantilever loads
Up to 04 kNm (40 kgm) wall length Cladding thickness ge 125 mm Knauf boards Up to 07 kNm (70 kgm) wall length Cladding thickness ge 15 mm Diamant (in acc to abP P-140592810) ge 18 mm Knauf boards
With Diamant Steel GKFI and a cover layer ge 125 mm Diamant GKFI (see following table) cantilever loads up to 15 kNm (150 kgm) on walls are possible
Selection of the grid in dependence on the expected loadLoad max Load
typeProfile min Cladding thickness min Furring
possibleLoaded side Unloaded sideKn
auf
Boar
ds
Diam
ant
Diam
ant
Stee
l GKF
I Minimum thickness
Knau
f Bo
ards
Diam
ant
Diam
ant
Stee
l GKF
I Minimum thickness
tmm
tmmkNm2
04 StaticCW 50 125 125 YesCW 50 125 125 Yes
07 StaticCW 50 125 + 04 125 + 04 Yes 2)
CW 75 18 18 Yes 2)
CW 75 15 15 Yes 2)
10 StaticCW 50
125 + 041) + 125 2x 125 Yes
CW 75 125 + 04 125 No
15 Static CW 75 125 + 04
+ 125 2x 125 No
1)ScrewspacingDrywallScrewsXTB1stlayerDiamantSteelGKFIle250mm2)IncaseofapplicationofpartitionheightsacctoDIN18183-1onlycantileverloadsupto04kNmarepossible
Fixing loadsFor fixing of cantilever loads
Dowel screw Maximum screw dowel load capacity in kgX-hooks Knauf Cavity Dowel
HartmutScrew M5
fischer MHD 5 x 65 SScrew M5 or M6
Knauf Multi-Purpose Screw FN 43 x 65
Plastic cavity dowelOslash 8 or 10 mm
Diamant125 mm 5 10 15 40 20 13 3015 18 mm 5 10 15 45 25 14 352x 125 mm 5 10 15 60 30 20 45ge 2x 125 mm 5 10 15 65 35 40 50Diamant Steel GKFI1x 125 + 04 mm 5 10 15 80 50 30 30 3)
2x 125 + 04 mm 5 10 15 100 90 60 55 3)
Measuredwith300mmeccentricity3)ValuesapplywithfischerplasticcavitydowelsUX8x50withKnaufMulti-PurposeScrewFN43x65orequivalent
Notes
Static loads in this respect are permanently fastened loads such as towel rails cabinets shelves and boilers Dynamic loads are exerted by fastened components which are subjected to continuous changes in load such as handrails fold-down seats and folding handles The use of traverses is required here see page 8Always screw fasten Diamant Steel GKFI with Diamant Screws XTB even for a cover layer of Diamant
7
Loads on partitions and furringsAnchoring in the cladding
RatingThe specified permissible cantilever loads are in accordance with the DIN 18183 or DIN 4103-1 at an eccentricity (spacing of resulting load to the wall surface) of max 300 mm The permissible load is reduced accordingly with greater eccentricity The determination of the permissible cantilever loads with divergent eccentricity is undertaken using the tables or diagrams on page 4 and page 5
Rating examples Determination of the permissible cabinet weight as well as the required minimum number of dowels (always ge 2)Metal stud partition W111de CW 50 cladding 125 mm Diamant GKFI acc to tableField of application static load max cantilever load 04 kNm (40 kgm) wall length Cabinet
widthCabinet depthmm
mm 100 200 300 400 500 600
400 31 28 25 22 19 16
600 465 42 375 33 285 24
800 62 56 50 44 38 32
1000 775 70 625 55 475 40
1200 93 84 75 66 57 48
Cabinet depth 400 mm cabinet width 1000 mm Max cabinet weight 55 kg
Cladding thickness 125 mm plastic cavity dowel
Max dowel load 30 kg
Required number of dowels 55 kg 30 kg = 18 2 dowels
are the min necessary
Metal stud partition W111de CW 75 cladding 2x 125 mm Diamant GKFI acc to diagramField of application static load max cantilever load 07 kNm (70 kgm) wall length
400
mm12001000
600
100 200 400 500 600mm
10
70
60
40
20 30
kg
100
80 90
110120
800
300
50
1
23
450
65
Cabinet depth
Cabinet width
Max permissible cabinet weightCabinet depth 450 mm cabinet width 800 mm
With cabinet depth 450 mm 1 vertically upwards up to the cabinet width line 800 mm
2 at the intersection point horizontal to the left ndash read off value 3
Max cabinet weight 65 kg
Cladding thickness 2x 125 mm Knauf Cavity Dowel Hartmut
Max dowel load 60 kg
Required number of dowels 65 kg 60 kg = 108 2 dowels
are the min necessary
8
Fields of applicationTraverses are built-in elements in lightweight partitions that transfer the fastening loads directly into the grid or into the flanking solid constructions
Selection of the traverse and grid in dependence on the expected loadFastening Load max Load type Profile min Cladding thickness min Independent
furring possible
Knauf Boards DiamantkNm2 mm mm
Steel anchoring traversesee page 14
07 Static CW 50 125 125 No07 Static CW 50 18 15 Yes10 Static CW 75 125 125 No10 Static CW 50 18 15 Yes
Metal traverse with gypsum fibre insertsee page 12
07 Static CW 50 125 125 No07 Static CW 50 18 15 Yes10 Static CW 75 125 125 No10 Static CW 50 18 15 Yes15 Static CW 50 18 15 No15 Static UA 50 18 15 Yes15 Dynamic UA 75 18 15 Yes
Multi-purpose traversesee page 10
07 Static CW 50 125 125 No07 Static CW 50 18 15 Yes10 Static CW 75 125 125 No10 Static CW 50 18 15 Yes15 Static CW 50 18 15 No15 Static UA 50 18 15 Yes15 Dynamic UA 75 18 15 Yes
Fixing loadsFor fixing of cantilever loads
Dowel screw Maximum screw dowel load capacity in kgKnauf Cavity Dowel Hartmut
fischer MHD 5 x 65 S
Knauf Multi- Purpose Screw FN 43 x 65
fischer plastic cavity dowels 8 x 50 with Knauf Multi-Purpose Screw FN 43 x 65
Wood screw Oslash 50 mm
Wood screw Oslash 60 mm
TraversesSteel anchoring traverse 75 ndash 45 40 45 45
Metal traversewith gypsum fibre insert
90 75 65 46 55 70
Multi-purpose traverse ndash ndash 125 ndash 115 165
Measuredwith300mmeccentricity
Loads on partitions and furringsAnchoring in the traverses
NotesStatic loads in this respect are permanently fastened loads such as towel rails cabinets shelves and boilers Dynamic loads are exerted by fastened components which are subjected to continuous changes in load such as handrails fold-down seats and folding handles
9
Loads on partitions and furringsAnchoring in the traverses
RatingThe specified permissible cantilever loads are in accordance with the DIN 18183 or DIN 4103-1 at an eccentricity (spacing of resulting load to the wall surface) of max 300 mm The permissible load is reduced accordingly with greater eccentricity The determination of the permissible cantilever loads with divergent eccentricity is undertaken using the tables or diagrams on page 4 and page 5
Rating examples Determination of the permissible cabinet weight as well as the required minimum number of dowels (always ge 2)Metal stud partition W111de CW 50 cladding 18 mm Knauf board acc to tableField of application static load max cantilever load 07 kNm (70 kgm) wall length Cabinet
widthCabinet depthmm
mm 100 200 300 400 500 600400 43 40 37 34 31 28600 645 60 555 51 465 42800 86 80 74 68 62 561000 1075 100 925 85 775 701200 129 120 111 102 93 84
Cabinet depth 500 mm cabinet width 800 mm Max cabinet weight 62 kg Fixing traverse Knauf Multi-Purpose Screw FN 43 x 65
Max screw load 45 kg
Required number of screws 62 kg 45 kg = 14 2 screws
are the min necessary
Metal stud partition W111de UA 75 cladding 15 mm Diamant GKFI acc to diagram
Field of application dynamic load max cantilever load 15 kNm (150 kgm) wall length
20
400
Cabinet depth100 200 600
Max permissible cabinet weight
140120
80
4060
kg
200
160
180
Cabinet width
mm
1000
1200
600
mm 300
100 800
240220
260280300320340
450400 500
165
1
23
Cabinet depth 450 mm cabinet width 800 mm
With cabinet depth 450 mm 1 vertically upwards up to the cabinet width line 800 mm
2 at the intersection point horizontal to the left read off value 3
Max cabinet weight 165 kg
Multi-purpose traverse Knauf Multi-Purpose Screw FN 43 x 65
Max screw load 125 kg
Required number of screws 165 kg 125 kg = 13 2 screws
are the min necessary
10
Knauf multi-purpose traversesThe multi-purpose traverse is suitable for accepting loads attached to the wall up to 15 kNm wall length eg cupboards boilers folding wall attached seats folding handles and similarThe multi-purpose traverse consists of a 23 mm thick multi-layer wooden board and galvanized sheet metal profiles It is fastened to the side of the floor-to-ceiling profilesThe attachment of the loads to the traverses should be performed using Knauf Multi-Purpose Screw FN
NoteTraverses for installation in damp and wet rooms see also system data sheet W38de Knauf Metal Stud Partitions AQUAPANELreg
Loads on partitions and furringsAnchoring in the traverses
Installation and applicationMulti-purpose traverse made of multi-layer wooden board and galvanized sheet metal profiles attached to the side of the CW studs UA profiles For CW studs screw fasten using the 6 enclosed Metal Screws LN 35 x 11 mm (3 per side) For UA profiles screw fasten with the 6 enclosed Drilling Screws ST 42 x 13 mm (3 per side)Arrangement in a rowUA profiles CW studs
Direction of installation Direction of installation
11
Loads on partitions and furringsAnchoring in the traverses
W234de-A10 View ndash Design with UA profile W234de-A13 View ndash Design with CW stud
W234de-H10 Horizontal section ndash Design with UA profile W234de-H13 Horizontal section ndash Design with CW studeg W626de eg W626de
W234de-V10 Vertical section ndash Design with UA profile W234de-V13 Vertical section ndash Design with CW studeg W116de eg W112de
Wooden board 555
Stud spacing 625 (grid dimension)
300
Multi-purpose traverse555 300 23 mm
Multi-layer wooden board
UA profile
Drillingscrew ST42 x 13(enclosed)
Wooden board 555
Stud spacing 625 (grid dimension)
300 Metal screw
LN 35 x 11(enclosed)
Multi-purpose traverse555 300 23 mm
Multi-layer wooden board
CW stud
Wooden board 555
Stud spacing 625 (grid dimension)
300
Multi-purpose traverse555 300 23 mm
UA profileDrilling screwST 42 x 13
Multi-purpose traverse555 300 23 mm
CW studMetal screwLN 35 x 11
48
eg folding wallattached seat
Knauf boardstrips
eg Supporthandle maxprojection 800 mm
Multi-purposetraverseUA profileKnauf boards
48
Multi-purposetraverseCW studKnauf boards
eg Cabinet
Scale 110 I Dimensions in mmDetails
Note No web cutouts in the CW studs are permissible for traverses to which the CW studs are attached
12
Knauf steel anchoring traverse with gypsum fibre insertThe steel anchoring traverse with gypsum fibre insert is suitable for accepting loads attached to the wall up to 15 kNm wall length eg cupboards shelves handrails and similarThe metal traverse with gypsum fibre insert consists of 075 mm thick sheet metal as well as an 18 mm thick gypsum fibre board It is fastened to the side of the floor-to-ceiling profiles The attachment of the loads to the traverses should be performed using Knauf Multi-Purpose Screw FNUse in partition systems where the requirement for non-combustible reaction to fire exists
Installation and applicationSteel anchoring traverse made of galvanized steel with gypsum fibre insert fastened to the CW studs UA profiles In case of CW studs crimp using a Stud Crimper and for UA profiles screw fasten with 6 Drilling screws LB 35 x 16 mmArrangement in a rowUA profiles CW studs
Loads on partitions and furringsAnchoring in the traverses
13
Scale 110 I Dimensions in mmDetailsW234de-A12 View - Design with UA profile W234de-A14 View - Design with CW stud
W234de-H12 Horizontal section - Design with UA profile W234de-H14 Horizontal section - Design with CW studeg W112de eg W112de
W234de-V12 Vertical section - Design with UA profile W234de-V14 Vertical section - Design with CW studeg W112de eg W112de
Traverse dimension 620
Stud spacing 625 (grid dimension)
290
Steel anchoring traversewith gypsum fibre insert
Traverse attached to UA profileusing drilling screws
UA profile
Steel anchoring traversewith gypsum fibre insert
CW stud
Crimp the traverse to the CW studusing a stud crimper
Traverse dimension 620
Stud spacing 625 (grid dimension)
290
Drilling screwLB 35 x 16
Steel anchoringtraverse with gypsum
fibre insert
UA profile Crimped Steel anchoring traversewith gypsum fibre insert
CW stud
eg Handrail
UA profileKnauf boards
Steel anchoring traversewith gypsum fibre insert
eg Handrail
CW studKnauf board
Steel anchoring traversewith gypsum fibre insert
Loads on partitions and furringsAnchoring in the traverses
Note No web cutouts in the CW studs are permissible for traverses to which the CW studs are attached
14
Loads on partitions and furringsAnchoring in the traverses
Knauf steel anchoring traverseThe steel anchoring traverse is suitable for accepting loads attached to the wall up to 10 kNm wall length eg towel holders cupboards shelves and similar Not suitable for dynamic loads such as folding wall attached seatsThe steel anchoring traverse consists of 075 mm thick sheet metal and are crimped onto the side using a stud crimper on the CW studs Particularly suitable for single-layer clad metal stud partitions and furrings where in case of cantilever loads gt 04 kNm (400 kgm) wall length the installation of a traverse is required
NoteTraverses for installation in damp and wet rooms see also system data sheet W38de Knauf Metal Stud Partitions AQUAPANELreg
Installation and applicationCrimp the steel anchoring traverse made of galvanized sheet steel to the CW studs using a Stud CrimperAdditional screw fastening of the steel anchoring traverse via screw fastening of the cladding (min 2 to 3 anchoring points) Reduce the screw spacing of the cladding if necessaryArrangement in a rowCW studs
Scale 110 I Dimensions in mmDetailsW234de-A11 View W234de V11 Vertical section
eg W111de
W234de-H11 Horizontal sectioneg W111de
Sheet metal gauge 075 mm
Steel anchoring traverse
CW stud
Crimp the traverse to the CW studusing the stud crimper
290
Traverse dimension 620
Stud spacing 625 (grid dimension)
eg Cabinet
CW stud
Knauf boardSteel anchoring traverse
Steel anchoring traverseCW stud
Crimped
Note No web cutouts in the CW studs are permissible for traverses to which the CW studs are attached
15
Full-length SanistandFloor-to-ceiling Sanistands made of galvanized UA profiles (min UA 75) 2 mm thick are suitable for transferring loads from traverses into the supporting structure or for fixing loads hanging onto walls such as school blackboards up to 15 kNm wall lengthFloor-to-ceiling Sanistands profiles are anchored to the basic floor and ceiling with door frame brackets or connection brackets for UA profiles The upper door frame bracket includes openings for routing cables such as pipe-in-pipe systems or electrical cablesThe loads are connected directly to the flange of the UA profile
W228de-A10 View
le 1000 mm
UW runnercontinuous
Door frameconnection brackettop connection withenclosed dowels
CW studAxial spacing suitedto partition system
UA profileas afloor-to-ceilingSanistand forbearing cantileverloads
UW runnercontinuous
Door frameconnection bracketbottom connectionwith enclosed dowels
Scale 110
Installation and applicationFloor-to-ceiling Sanistands made of UA profiles must be anchored to the basic floor and ceiling with door frame brackets or connection brackets for UA profiles The upper door frame bracket includes openings for routing cables such as pipe-in-pipe systems or electrical cables Fasten objects to UA profiles using threaded rods U washers and M1012 steel nuts or self-tapping screws
Loads on partitions and furringsFull-length Sanistand
Detail
Notes
Web cutouts are not permissible in UA Sanistand subject to cantilever loads point loads or linear distributed loadsMaximum screw load with connections to full height Sanistand (UA profile)Every UA profile flange and anchoring point may not exceed a resulting pull-out load of 150 kN (150 kg)Components similar to cantilevers such as foldable rails should be screwed onto two adjacent UA profilesUse suitable drilling screws eg Ejot Zebra Piasta Hilti S-MD or comparable
16
Loads on partitions and furringsFull-length Sanistand
Scale 110DetailsW116de-V1 Sanistand W116de-H1 SanistandVertical section I Without fire resistance Horizontal section I Without fire resistance
UW runnerUniflott + Trenn-Fix
UW runner
Additional UA profile
Sanistand withconcealed mount cistern
Knauf connectionbracket with enclosedM8 carriage bolts
Knauf conection bracket withenclosed M8 carriage bolt
2x 125 mm DiamantDiamant screw XTB
Additional CW stud
Knauf sealing tape
Board strip installationacc to W11de systemdata sheet
Stud spacing le 625 mm
CW stud profile
Additional CW studBoard strip installation in acc with W11de system data sheet
Knauf connection bracket withenclosed M8 carriage bolts
Additional UA profileSanitand with concealedmount cistern
Notes
Max partition height UA 50 = 300 m UA 75 = see system data sheet W11de Knauf Metal Stud Partition for the wall heights
Minimum cladding ge 18 mm Knauf Boards recommendation 2x 125 mm Knauf Diamant
Web cutouts are not permissible in UA Sanistand subject to cantilever loads point loads or linear distributed loadsObserve the manufacturersrsquo details for lateral UA profiles and cladding Additional UA profiles are required laterally on Sanistand mounts acc to DIN 18340 section 374 Only possible without additional UA profiles if the manufacturer of the Sanistand base or WC Sanistand permits itDeviating specifications of the Sanistand manufacturer must be considered and observed
17
Loads on partitions and furringsFull-length Sanistand
Notes
Max partition height rear W112de UA 50 = 300 m UA 75 = see system data sheet W11de Knauf Metal Stud Partition for the wall heights
Minimum cladding front wall installations ge 18 mm Knauf Boards recommendation 2x 125 mm Knauf Diamant
Web cutouts are not permissible in UA Sanistand subject to cantilever loads point loads or linear distributed loadsObserve the manufacturersrsquo details for lateral UA profiles and cladding Additional UA profiles are required laterally on Sanistand mounts acc to DIN 18340 section 374 Only possible without additional UA profiles if the manufacturer of the Sanistand base or WC Sanistand permits itDeviating specifications of the Sanistand manufacturer must be considered and observed
Scale 110DetailsW626Vde-V1 Without back anchoring W626Vde-H1 Without back anchoring Vertical section Horizontal section
UW runnerUniflott + Trenn-Fix
UW runner
Additional UA profile
Sanistand withconcealed mount cistern
Knauf connection bracket withenclosed M8 carriage bolt
Knauf connection bracket withenclosed M8 carriage bolt
2x 125 mm DiamantDiamant screw XTB
Knauf sealing tape
Sanistand withconcealed mount cisternKnauf connection bracket with
enclosed M8 carriage bolts
Stud spacing le 625 mm
UW runner
Knauf boardsCW stud
Additional UA profile
18
Loads on partitions and furringsFull-length Sanistand
Scale 110DetailsW626Vde-V2 Back anchoring in traverse W626Vde-H2 Back anchoring in traverse Vertical section Horizontal section
Sanistand withconcealed mount cistern
SealantUD profile made of insulation strips
UW runner
UW runner
UA profile
Knauf multi-purpose screw FN
Uniflott + Trenn-Fix
Multi-purpose traverse 555 300 23 mm
Knauf connection bracket withenclosed M8 carriage bolts
2x 125 mm DiamantDiamant screw XTB
Knauf connection bracket withenclosed M8 carriage bolt
Wall anchor installation acc to WCSanistand manufacturer specifications
Knauf sealing tape
Stud spacing le 625 mm
Multi-purpose traverse555 300 23 mm
UA profile
UA profile
Knauf connection bracket withenclosed M8 carriage bolt
Knauf connectionbracket with enclosedM8 carriage bolt
Wall anchorinstallation acc to
WC Sanistandmanufacturerspecifications
Notes
Max partition height rear W112de UA 50 = 300 m UA 75 = see system data sheet W11de Knauf Metal Stud Partitions for the wall heights
Minimum cladding front wall installations ge 18 mm Knauf Boards recommendation 2x 125 mm Knauf Diamant
Web cutouts are not permissible in UA Sanistand subject to cantilever loads point loads or linear distributed loadsObserve the manufacturersrsquo details for lateral UA profiles and cladding Additional UA profiles are required laterally on Sanistand mounts acc to DIN 18340 section 374 Only possible without additional UA profiles if the manufacturer of the Sanistand base or WC Sanistand permits itDeviating specifications of the Sanistand manufacturer must be considered and observed
19
Loads on partitions and furringsFull-length Sanistand
Scale 110DetailsW626Vde-V3 Back anchoring in UA profile W626Vde-H3 Back anchoring in UA profile Vertical section Horizontal section
Sanistand withconcealed mount cistern
SealantUD profile on insulation strips
UW runner
UW runner
Additional UA profile
Knauf multi-purpose screw FN
Uniflott + Trenn-Fix
UA profile
Knauf connection bracket withenclosed M8 carriage bolts
2x 125 mm DiamantDiamant screw XTB
Knauf connection bracket withenclosed M8 carriage bolts
Fixing bolts with nuts andwashers
Knauf sealing tape
Stud spacing le 625 mm
Additional UA profile
UA profile Fixing bolts with nutsand washers
Knauf connection bracket withenclosed M8 carriage bolts
Knauf connectionbracket with enclosedM8 carriage bolts
Notes
Max partition height at rear W112de UA 50 = 300 m UA 75 = see system data sheet W11de Knauf Metal Stud Partition for the wall heights
Minimum cladding front wall installations ge 18 mm Knauf Boards recommendation 2x 125 mm Knauf Diamant
Web cutouts are not permissible in UA Sanistand subject to cantilever loads point loads or linear distributed loadsObserve the manufacturersrsquo details for lateral UA profiles and cladding Additional UA profiles are required laterally on Sanistand mounts acc to DIN 18340 section 374 Only possible without additional UA profiles if the manufacturer of the Sanistand base or WC Sanistand permits itDeviating specifications of the Sanistand manufacturer must be considered and observed
20
Loads on partitions and furringsFull-length Sanistand
Scale 110DetailsW626Vde-V4 Back anchoring in mounting rail W626Vde-H4 Back anchoring in mounting rail Vertical section Horizontal section
Sanistand withconcealed mount cistern
2x 125 mm Diamant
SealantUD profile on insulation strips
UW runner
Diamant screw XTB
UA profile
Knauf multi-purpose screw FN
Mounting rail with fixing screw
Knauf connection bracket withenclosed M8 carriage bolt
Uniflott + Trenn-Fix
UA profile
Knauf connection bracket withenclosed M8 carriage bolt
Knauf sealing tapeUW runner
Stud spacing le 625 mm
UA profile
UA profile
Mounting railFixing screw
Mounting screw
Sanistand withconcealed mount cistern
Knauf connection bracket withenclosed M8 carriage bolt
Knauf connectionbracket with enclosedM8 carriage bolt
Notes
Max partition height rear W112de UA 50 = 300 m UA 75 = see system data sheet W11de Knauf Metal Stud Partitions for the wall heights
Minimum cladding front wall installations ge 18 mm Knauf Boards recommendation 2x 125 mm Knauf Diamant
Web cutouts are not permissible in UA Sanistand subject to cantilever loads point loads or linear distributed loadsObserve the manufacturersrsquo details for lateral UA profiles and cladding Additional UA profiles are required laterally on Sanistand mounts acc to DIN 18340 section 374 Only possible without additional UA profiles if the manufacturer of the Sanistand base or WC Sanistand permits itDeviating specifications of the Sanistand manufacturer must be considered and observed
21
Notes
In case of load attachment to ldquomulti-level ceiling systemsrdquo refer to the respective valid Knauf system data sheetsIn case of attachment of loads to free-spanning ceilings see system data sheet D13de Knauf Free-Spanning Ceilings
Attachment of loads to Knauf board ceilingsAdditional loads eg lighting fixtures curtain rails and similar can be fixed to Knauf board ceilings using universal dowels cavity dowels spring toggle dowels or Knauf Hartmut Hohlraumduumlbel cavity dowelsAdditional loads must be considered when determining the load class
NoteHeavy loads must be attached directly on load-bearing building elements (basic ceiling) or on auxiliary constructions eg traverses
For each area under load of the Knauf board ceiling the weight of thefastened components may not exceed the following limits
Permissible weight per ceiling area in kgmsup2Without fire resistance With fire resistance1)
15 61)Incaseofapplicationasafireresistanceceilingwithexposedceiling(multi-levelceilingsystem)15kgmsup2totalweightispermissiblefortheexposedceiling(includinginsulationlayerandattachedloads)attachedtothefireresistanceceiling
Furthermore the following conditions applyFor each anchoring point the components fastened to the board ceiling may not exceed the following weights
Fastening method Permissible weight per anchoring point in kgWithout fire resistance With fire resistance
Fastening in the cladding 6 05
Fastening to the grid 10 10
Fastening in the claddingKnauf Hartmut Hohlraumduumlbel cavity dowelScrew M5
Fastening to the gridKnauf Universalschraube FN multi-purpose screw eg curtain rail
The minimum separation spacings between individual attached loads must be observed to avoid local overloading of the ceiling The minimum separation clearance between two attachment points consists of both load radii for the point loadsThe load radius of a point load can be taken from the following diagram in dependence on the permissible weight per unit area for additional loads
Point load in kg
7570656055504540353025201510
0 2 3 4 5 6 7 8 9 10
Radiu
s in c
m
1
50
Fastening in the claddingpossible (without fire resistance)
3 kgmsup2 permissible additional weight (on the exposed ceiling under a fire resistance ceiling refer to the respective valid Knauf system data sheets)6 kgmsup2 permissible additional weight (with fire resistance)15 kgmsup2 permissible additional weight (without fire resistance)
Example fastening scheme at 15 kgmsup2
05 kg
10 kg
3 kgr = 25 cm
r = 46 cm
6 kgr = 355 cm
1 kg
r = 15 cm
r = 105 cm
NoteThe anchored loads can be transferred using several anchoring elements
Loads on board ceilingsFastening in the cladding grid
22
Knauf multi-purpose traversesThe multi-purpose traverse in Knauf board ceilings is suitable for the application of point loads up to 075 kN eg chandeliers music speakers or similarThe multi-purpose traverse consists of a 23 mm thick multi-layer wooden board and galvanized sheet metal profiles It is fastened to the side of the CD furring channelThe attachment of the loads to the traverses should be performed using Knauf Multi-Purpose Screw FNInstallation is possible in a double layer profile grid and flush profile grid
Installation and applicationBend the Daisy chain clip before lateral screw fastening The Daisy chain clip is then Z shaped The unpunched metal side of the Daisy chain clip is pushed onto the lower side of the traverse and then screw fastened laterally through the factory-made hole on the long side of the traverse Screw fasten 4x Daisy chain clips each using one drywall screw TN 35 x 35 about 100 mm from the corner of the multi-layer board on the long edge of the multi-purpose traverse Arrange an additional CD channel (length ge 650 mm) for every long edge in accordance with the width of the multi-purpose traverse Alternately a ceiling furring channel can be used for application of the multi-purpose traverse The supporting profiles are suspended using ceiling suspenders of load class 40 kg The suspenders may not be situated in the direct vicinity of the longitudinal area of the traverse as this will hinder the installation of the traverse Introduce the multi-purpose traverse between the support profiles bend the Daisy chain clip around the CD channel and engage it In case of single-layer cladding do not screw fasten the surface cladding with the multi-purpose traverse
1 Apply the Daisy chain clip 2 Bend the Daisy chain clip 3 Screw fasten the Daisy chain clip
Loads on board ceilingsAnchoring in the traverses
100 mm
23
Loads on board ceilingsAnchoring in the traverses
Scale 110 I Dimensions in mmDetailsD112de SO18 Vertical section ndash Multi-purpose traverse D113de SO12 Vertical section ndash Multi-purpose traverseeg with two additional CD channels I Without fire resistance eg with one additional CD channel I Without fire resistance
D112de SO19 Vertical section ndash Multi-purpose traverse D113de SO13 Vertical section ndash Multi-purpose traverseeg with two additional CD channels I Without fire resistance eg with one additional CD channel I Without fire resistance
D112de SO20 Top view ndash Multi-purpose traverse D113de SO14 Top view ndash Multi-purpose traverseeg with two additional CD channels I Without fire resistance eg with one additional CD channel I Without fire resistance
Fasten Daisy chain clip with drywall screwTN 35 x 35 to multi-purpose traverse
Additional CD channel with two suspendersLoad bearing capacity class ge 040 kN
Multi-purposetraverse555 300 23 mm
300
Furring channel spacing 500
Fasten Daisy chain clip with drywall screwTN 35 x 35 to multi-purpose traverse
Additional suspended load bearing capacity class ge 040 kNMulti-purposetraverse555 300 23 mm
300
Furring channel spacing 500
Additional CD channel with two suspendersLoad bearing capacity class ge 040 kN
Multi-purposetraverse555 300 23 mm
Fasten Daisy chain clip with drywall screwTN 35 x 35 to multi-purpose traverse
Wood panel 555approx
100
Additional suspenderload bearing capacityclass ge 040 kN
Multi-purposetraverse555 300 23 mm
Fasten Daisy chain clip with drywall screwTN 35 x 35 to multi-purpose traverse
Wood panel 555approx
100
Daisy chain clip
Furring channel spacing 500
Traverse
CDchannel
Multi-layerwood panel
Furring channel spacing 500
Multi-purposetraverse
Daisy chain clip
Multi-layerwood panel
Additional grid 4 additional suspension points (eg Nonius suspension)
All technical changes reserved Only the current printed instructions are valid The stated information represents current state-of-the-art Knauf technology The entire state of approved engineering rules appropriate standards guidelines and rules of crafts-manship are not included herewith These and all application instructions have to be adhered to separately by the installer Our warranty is expressly limited to our products in flawless condition All application quantities and delivery amounts are based on empirical data that are not easily transferable to other deviating areasAll rights reserved All amendments reprints and photocopies including those of excerpts require our expressed permission
The stated constructional and structural design specifications and characteristics of building physics of Knauf systems can only be ensured with the exclusive use of Knauf system components or other products expressly recommended by Knauf
Knauf Gips KG Am Bahnhof 7 97346 Iphofen GermanyKnauf DirectTechnical Advisory Service
knauf-direktknaufde
wwwknaufde
VT03deeng09190TI
The iPad App Knauf Infothek now provides all the current information and documents from Knauf Gips KG at any time and in every location in a clear and comfortable wayKnauf Infothek
Videos for Knauf systems and products can be found under the following linkwwwyoutubecomknaufEPD
4
Loads on partitions and furringsCantilever loads
Rating diagrams
Cabinet widthCabinet depth
Cabin
et he
ight
ge 30
0 mm
le 600 mmle 1200 mm
Eccentricityle 300 mm
The specified permissible cantilever loads are in accordance with the DIN 18183 or DIN 4103-1 at an eccentricity (spacing of load resulting to the wall surface) of max 300 mm The permissible load is reduced accordingly with greater eccentricity The following tables and diagrams are intended as an aid in the determination of the permissible cantilever loads with divergent eccentricity The values can be taken either from the tables or the diagrams
Up to 04 kNm (40 kgm) wall lengthMaximum permissible cabinet weight (kg) acc to table
Cabinet widthmm
Cabinet depthmm100 200 300 400 500 600
400 31 28 25 22 19 16600 465 42 375 33 285 24800 62 56 50 44 38 321000 775 70 625 55 475 401200 93 84 75 66 57 48
Assume the worst-case value with intermediate values or diagram procedure
orMaximum permissible cabinet weight (kg) acc to diagram
10
70
60
40
20
100
80
90
50
Cabinet depthmm 100 200 300 400 500 600
1000 800 600 400
30
Max permissible cabinet weight
kg
Cabinet width
mm1200
Up to 07 kNm (70 kgm) wall length Maximum permissible cabinet weight (kg) acc to table
Cabinet widthmm
Cabinet depthmm100 200 300 400 500 600
400 43 40 37 34 31 28600 645 60 555 51 465 42800 86 80 74 68 62 561000 1075 100 925 85 775 701200 129 120 111 102 93 84
Assume the worst-case value with intermediate values or diagram procedure
orMaximum permissible cabinet weight (kg) acc to diagram
kg
Max permissible cabinet weight
Cabinet width
mm1200
1000
400
600
800
mmCabinet depth
600100 200 300 400 500
10
70
60
40
20
30
100
80
90
110
120
50
5
Loads on partitions and furringsCantilever loads
Up to 10 kNm (100 kgm) wall lengthMaximum permissible cabinet weight (kg) acc to table
Cabinet widthmm
Cabinet depthmm100 200 300 400 500 600
400 90 80 70 60 50 40600 135 120 105 90 75 60800 180 160 140 120 100 801000 225 200 175 150 125 1001200 270 240 210 180 150 120
Assume the worst-case value with intermediate values or diagram procedure
orMaximum permissible cabinet weight (kg) acc to diagramMax permissible cabinet weight
kgCabinet width
mm1200
400
1000
600
800
Cabinet depthmm 600100 200 300 400 500
20
140
120
80
40
60
200
160
180
100
240
220
260
280
300
Up to 15 kNm (150 kgm) wall lengthMaximum permissible cabinet weight (kg) acc to table
Cabinet widthmm
Cabinet depthmm100 200 300 400 500 600
400 135 120 105 90 75 60600 202 180 157 135 112 90800 270 240 210 180 150 1201000 337 300 262 225 187 1501200 360 360 315 270 225 180
Assume the worst-case value with intermediate values or diagram procedure
orMaximum permissible cabinet weight (kg) acc to diagram
400
mm
1000
1200
600
800
Max permissible cabinet weight
kgCabinet width
Cabinet depthmm 600500400300200100
20
140
120
80
40
60
200
160
180
100
240
220
260
280
300
320
340
6
Loads on partitions and furringsFastening in the cladding
Fields of applicationAccording to DIN 18183 the metal stud partitions and independent furrings can be loaded at any position by cantilever loads
Up to 04 kNm (40 kgm) wall length Cladding thickness ge 125 mm Knauf boards Up to 07 kNm (70 kgm) wall length Cladding thickness ge 15 mm Diamant (in acc to abP P-140592810) ge 18 mm Knauf boards
With Diamant Steel GKFI and a cover layer ge 125 mm Diamant GKFI (see following table) cantilever loads up to 15 kNm (150 kgm) on walls are possible
Selection of the grid in dependence on the expected loadLoad max Load
typeProfile min Cladding thickness min Furring
possibleLoaded side Unloaded sideKn
auf
Boar
ds
Diam
ant
Diam
ant
Stee
l GKF
I Minimum thickness
Knau
f Bo
ards
Diam
ant
Diam
ant
Stee
l GKF
I Minimum thickness
tmm
tmmkNm2
04 StaticCW 50 125 125 YesCW 50 125 125 Yes
07 StaticCW 50 125 + 04 125 + 04 Yes 2)
CW 75 18 18 Yes 2)
CW 75 15 15 Yes 2)
10 StaticCW 50
125 + 041) + 125 2x 125 Yes
CW 75 125 + 04 125 No
15 Static CW 75 125 + 04
+ 125 2x 125 No
1)ScrewspacingDrywallScrewsXTB1stlayerDiamantSteelGKFIle250mm2)IncaseofapplicationofpartitionheightsacctoDIN18183-1onlycantileverloadsupto04kNmarepossible
Fixing loadsFor fixing of cantilever loads
Dowel screw Maximum screw dowel load capacity in kgX-hooks Knauf Cavity Dowel
HartmutScrew M5
fischer MHD 5 x 65 SScrew M5 or M6
Knauf Multi-Purpose Screw FN 43 x 65
Plastic cavity dowelOslash 8 or 10 mm
Diamant125 mm 5 10 15 40 20 13 3015 18 mm 5 10 15 45 25 14 352x 125 mm 5 10 15 60 30 20 45ge 2x 125 mm 5 10 15 65 35 40 50Diamant Steel GKFI1x 125 + 04 mm 5 10 15 80 50 30 30 3)
2x 125 + 04 mm 5 10 15 100 90 60 55 3)
Measuredwith300mmeccentricity3)ValuesapplywithfischerplasticcavitydowelsUX8x50withKnaufMulti-PurposeScrewFN43x65orequivalent
Notes
Static loads in this respect are permanently fastened loads such as towel rails cabinets shelves and boilers Dynamic loads are exerted by fastened components which are subjected to continuous changes in load such as handrails fold-down seats and folding handles The use of traverses is required here see page 8Always screw fasten Diamant Steel GKFI with Diamant Screws XTB even for a cover layer of Diamant
7
Loads on partitions and furringsAnchoring in the cladding
RatingThe specified permissible cantilever loads are in accordance with the DIN 18183 or DIN 4103-1 at an eccentricity (spacing of resulting load to the wall surface) of max 300 mm The permissible load is reduced accordingly with greater eccentricity The determination of the permissible cantilever loads with divergent eccentricity is undertaken using the tables or diagrams on page 4 and page 5
Rating examples Determination of the permissible cabinet weight as well as the required minimum number of dowels (always ge 2)Metal stud partition W111de CW 50 cladding 125 mm Diamant GKFI acc to tableField of application static load max cantilever load 04 kNm (40 kgm) wall length Cabinet
widthCabinet depthmm
mm 100 200 300 400 500 600
400 31 28 25 22 19 16
600 465 42 375 33 285 24
800 62 56 50 44 38 32
1000 775 70 625 55 475 40
1200 93 84 75 66 57 48
Cabinet depth 400 mm cabinet width 1000 mm Max cabinet weight 55 kg
Cladding thickness 125 mm plastic cavity dowel
Max dowel load 30 kg
Required number of dowels 55 kg 30 kg = 18 2 dowels
are the min necessary
Metal stud partition W111de CW 75 cladding 2x 125 mm Diamant GKFI acc to diagramField of application static load max cantilever load 07 kNm (70 kgm) wall length
400
mm12001000
600
100 200 400 500 600mm
10
70
60
40
20 30
kg
100
80 90
110120
800
300
50
1
23
450
65
Cabinet depth
Cabinet width
Max permissible cabinet weightCabinet depth 450 mm cabinet width 800 mm
With cabinet depth 450 mm 1 vertically upwards up to the cabinet width line 800 mm
2 at the intersection point horizontal to the left ndash read off value 3
Max cabinet weight 65 kg
Cladding thickness 2x 125 mm Knauf Cavity Dowel Hartmut
Max dowel load 60 kg
Required number of dowels 65 kg 60 kg = 108 2 dowels
are the min necessary
8
Fields of applicationTraverses are built-in elements in lightweight partitions that transfer the fastening loads directly into the grid or into the flanking solid constructions
Selection of the traverse and grid in dependence on the expected loadFastening Load max Load type Profile min Cladding thickness min Independent
furring possible
Knauf Boards DiamantkNm2 mm mm
Steel anchoring traversesee page 14
07 Static CW 50 125 125 No07 Static CW 50 18 15 Yes10 Static CW 75 125 125 No10 Static CW 50 18 15 Yes
Metal traverse with gypsum fibre insertsee page 12
07 Static CW 50 125 125 No07 Static CW 50 18 15 Yes10 Static CW 75 125 125 No10 Static CW 50 18 15 Yes15 Static CW 50 18 15 No15 Static UA 50 18 15 Yes15 Dynamic UA 75 18 15 Yes
Multi-purpose traversesee page 10
07 Static CW 50 125 125 No07 Static CW 50 18 15 Yes10 Static CW 75 125 125 No10 Static CW 50 18 15 Yes15 Static CW 50 18 15 No15 Static UA 50 18 15 Yes15 Dynamic UA 75 18 15 Yes
Fixing loadsFor fixing of cantilever loads
Dowel screw Maximum screw dowel load capacity in kgKnauf Cavity Dowel Hartmut
fischer MHD 5 x 65 S
Knauf Multi- Purpose Screw FN 43 x 65
fischer plastic cavity dowels 8 x 50 with Knauf Multi-Purpose Screw FN 43 x 65
Wood screw Oslash 50 mm
Wood screw Oslash 60 mm
TraversesSteel anchoring traverse 75 ndash 45 40 45 45
Metal traversewith gypsum fibre insert
90 75 65 46 55 70
Multi-purpose traverse ndash ndash 125 ndash 115 165
Measuredwith300mmeccentricity
Loads on partitions and furringsAnchoring in the traverses
NotesStatic loads in this respect are permanently fastened loads such as towel rails cabinets shelves and boilers Dynamic loads are exerted by fastened components which are subjected to continuous changes in load such as handrails fold-down seats and folding handles
9
Loads on partitions and furringsAnchoring in the traverses
RatingThe specified permissible cantilever loads are in accordance with the DIN 18183 or DIN 4103-1 at an eccentricity (spacing of resulting load to the wall surface) of max 300 mm The permissible load is reduced accordingly with greater eccentricity The determination of the permissible cantilever loads with divergent eccentricity is undertaken using the tables or diagrams on page 4 and page 5
Rating examples Determination of the permissible cabinet weight as well as the required minimum number of dowels (always ge 2)Metal stud partition W111de CW 50 cladding 18 mm Knauf board acc to tableField of application static load max cantilever load 07 kNm (70 kgm) wall length Cabinet
widthCabinet depthmm
mm 100 200 300 400 500 600400 43 40 37 34 31 28600 645 60 555 51 465 42800 86 80 74 68 62 561000 1075 100 925 85 775 701200 129 120 111 102 93 84
Cabinet depth 500 mm cabinet width 800 mm Max cabinet weight 62 kg Fixing traverse Knauf Multi-Purpose Screw FN 43 x 65
Max screw load 45 kg
Required number of screws 62 kg 45 kg = 14 2 screws
are the min necessary
Metal stud partition W111de UA 75 cladding 15 mm Diamant GKFI acc to diagram
Field of application dynamic load max cantilever load 15 kNm (150 kgm) wall length
20
400
Cabinet depth100 200 600
Max permissible cabinet weight
140120
80
4060
kg
200
160
180
Cabinet width
mm
1000
1200
600
mm 300
100 800
240220
260280300320340
450400 500
165
1
23
Cabinet depth 450 mm cabinet width 800 mm
With cabinet depth 450 mm 1 vertically upwards up to the cabinet width line 800 mm
2 at the intersection point horizontal to the left read off value 3
Max cabinet weight 165 kg
Multi-purpose traverse Knauf Multi-Purpose Screw FN 43 x 65
Max screw load 125 kg
Required number of screws 165 kg 125 kg = 13 2 screws
are the min necessary
10
Knauf multi-purpose traversesThe multi-purpose traverse is suitable for accepting loads attached to the wall up to 15 kNm wall length eg cupboards boilers folding wall attached seats folding handles and similarThe multi-purpose traverse consists of a 23 mm thick multi-layer wooden board and galvanized sheet metal profiles It is fastened to the side of the floor-to-ceiling profilesThe attachment of the loads to the traverses should be performed using Knauf Multi-Purpose Screw FN
NoteTraverses for installation in damp and wet rooms see also system data sheet W38de Knauf Metal Stud Partitions AQUAPANELreg
Loads on partitions and furringsAnchoring in the traverses
Installation and applicationMulti-purpose traverse made of multi-layer wooden board and galvanized sheet metal profiles attached to the side of the CW studs UA profiles For CW studs screw fasten using the 6 enclosed Metal Screws LN 35 x 11 mm (3 per side) For UA profiles screw fasten with the 6 enclosed Drilling Screws ST 42 x 13 mm (3 per side)Arrangement in a rowUA profiles CW studs
Direction of installation Direction of installation
11
Loads on partitions and furringsAnchoring in the traverses
W234de-A10 View ndash Design with UA profile W234de-A13 View ndash Design with CW stud
W234de-H10 Horizontal section ndash Design with UA profile W234de-H13 Horizontal section ndash Design with CW studeg W626de eg W626de
W234de-V10 Vertical section ndash Design with UA profile W234de-V13 Vertical section ndash Design with CW studeg W116de eg W112de
Wooden board 555
Stud spacing 625 (grid dimension)
300
Multi-purpose traverse555 300 23 mm
Multi-layer wooden board
UA profile
Drillingscrew ST42 x 13(enclosed)
Wooden board 555
Stud spacing 625 (grid dimension)
300 Metal screw
LN 35 x 11(enclosed)
Multi-purpose traverse555 300 23 mm
Multi-layer wooden board
CW stud
Wooden board 555
Stud spacing 625 (grid dimension)
300
Multi-purpose traverse555 300 23 mm
UA profileDrilling screwST 42 x 13
Multi-purpose traverse555 300 23 mm
CW studMetal screwLN 35 x 11
48
eg folding wallattached seat
Knauf boardstrips
eg Supporthandle maxprojection 800 mm
Multi-purposetraverseUA profileKnauf boards
48
Multi-purposetraverseCW studKnauf boards
eg Cabinet
Scale 110 I Dimensions in mmDetails
Note No web cutouts in the CW studs are permissible for traverses to which the CW studs are attached
12
Knauf steel anchoring traverse with gypsum fibre insertThe steel anchoring traverse with gypsum fibre insert is suitable for accepting loads attached to the wall up to 15 kNm wall length eg cupboards shelves handrails and similarThe metal traverse with gypsum fibre insert consists of 075 mm thick sheet metal as well as an 18 mm thick gypsum fibre board It is fastened to the side of the floor-to-ceiling profiles The attachment of the loads to the traverses should be performed using Knauf Multi-Purpose Screw FNUse in partition systems where the requirement for non-combustible reaction to fire exists
Installation and applicationSteel anchoring traverse made of galvanized steel with gypsum fibre insert fastened to the CW studs UA profiles In case of CW studs crimp using a Stud Crimper and for UA profiles screw fasten with 6 Drilling screws LB 35 x 16 mmArrangement in a rowUA profiles CW studs
Loads on partitions and furringsAnchoring in the traverses
13
Scale 110 I Dimensions in mmDetailsW234de-A12 View - Design with UA profile W234de-A14 View - Design with CW stud
W234de-H12 Horizontal section - Design with UA profile W234de-H14 Horizontal section - Design with CW studeg W112de eg W112de
W234de-V12 Vertical section - Design with UA profile W234de-V14 Vertical section - Design with CW studeg W112de eg W112de
Traverse dimension 620
Stud spacing 625 (grid dimension)
290
Steel anchoring traversewith gypsum fibre insert
Traverse attached to UA profileusing drilling screws
UA profile
Steel anchoring traversewith gypsum fibre insert
CW stud
Crimp the traverse to the CW studusing a stud crimper
Traverse dimension 620
Stud spacing 625 (grid dimension)
290
Drilling screwLB 35 x 16
Steel anchoringtraverse with gypsum
fibre insert
UA profile Crimped Steel anchoring traversewith gypsum fibre insert
CW stud
eg Handrail
UA profileKnauf boards
Steel anchoring traversewith gypsum fibre insert
eg Handrail
CW studKnauf board
Steel anchoring traversewith gypsum fibre insert
Loads on partitions and furringsAnchoring in the traverses
Note No web cutouts in the CW studs are permissible for traverses to which the CW studs are attached
14
Loads on partitions and furringsAnchoring in the traverses
Knauf steel anchoring traverseThe steel anchoring traverse is suitable for accepting loads attached to the wall up to 10 kNm wall length eg towel holders cupboards shelves and similar Not suitable for dynamic loads such as folding wall attached seatsThe steel anchoring traverse consists of 075 mm thick sheet metal and are crimped onto the side using a stud crimper on the CW studs Particularly suitable for single-layer clad metal stud partitions and furrings where in case of cantilever loads gt 04 kNm (400 kgm) wall length the installation of a traverse is required
NoteTraverses for installation in damp and wet rooms see also system data sheet W38de Knauf Metal Stud Partitions AQUAPANELreg
Installation and applicationCrimp the steel anchoring traverse made of galvanized sheet steel to the CW studs using a Stud CrimperAdditional screw fastening of the steel anchoring traverse via screw fastening of the cladding (min 2 to 3 anchoring points) Reduce the screw spacing of the cladding if necessaryArrangement in a rowCW studs
Scale 110 I Dimensions in mmDetailsW234de-A11 View W234de V11 Vertical section
eg W111de
W234de-H11 Horizontal sectioneg W111de
Sheet metal gauge 075 mm
Steel anchoring traverse
CW stud
Crimp the traverse to the CW studusing the stud crimper
290
Traverse dimension 620
Stud spacing 625 (grid dimension)
eg Cabinet
CW stud
Knauf boardSteel anchoring traverse
Steel anchoring traverseCW stud
Crimped
Note No web cutouts in the CW studs are permissible for traverses to which the CW studs are attached
15
Full-length SanistandFloor-to-ceiling Sanistands made of galvanized UA profiles (min UA 75) 2 mm thick are suitable for transferring loads from traverses into the supporting structure or for fixing loads hanging onto walls such as school blackboards up to 15 kNm wall lengthFloor-to-ceiling Sanistands profiles are anchored to the basic floor and ceiling with door frame brackets or connection brackets for UA profiles The upper door frame bracket includes openings for routing cables such as pipe-in-pipe systems or electrical cablesThe loads are connected directly to the flange of the UA profile
W228de-A10 View
le 1000 mm
UW runnercontinuous
Door frameconnection brackettop connection withenclosed dowels
CW studAxial spacing suitedto partition system
UA profileas afloor-to-ceilingSanistand forbearing cantileverloads
UW runnercontinuous
Door frameconnection bracketbottom connectionwith enclosed dowels
Scale 110
Installation and applicationFloor-to-ceiling Sanistands made of UA profiles must be anchored to the basic floor and ceiling with door frame brackets or connection brackets for UA profiles The upper door frame bracket includes openings for routing cables such as pipe-in-pipe systems or electrical cables Fasten objects to UA profiles using threaded rods U washers and M1012 steel nuts or self-tapping screws
Loads on partitions and furringsFull-length Sanistand
Detail
Notes
Web cutouts are not permissible in UA Sanistand subject to cantilever loads point loads or linear distributed loadsMaximum screw load with connections to full height Sanistand (UA profile)Every UA profile flange and anchoring point may not exceed a resulting pull-out load of 150 kN (150 kg)Components similar to cantilevers such as foldable rails should be screwed onto two adjacent UA profilesUse suitable drilling screws eg Ejot Zebra Piasta Hilti S-MD or comparable
16
Loads on partitions and furringsFull-length Sanistand
Scale 110DetailsW116de-V1 Sanistand W116de-H1 SanistandVertical section I Without fire resistance Horizontal section I Without fire resistance
UW runnerUniflott + Trenn-Fix
UW runner
Additional UA profile
Sanistand withconcealed mount cistern
Knauf connectionbracket with enclosedM8 carriage bolts
Knauf conection bracket withenclosed M8 carriage bolt
2x 125 mm DiamantDiamant screw XTB
Additional CW stud
Knauf sealing tape
Board strip installationacc to W11de systemdata sheet
Stud spacing le 625 mm
CW stud profile
Additional CW studBoard strip installation in acc with W11de system data sheet
Knauf connection bracket withenclosed M8 carriage bolts
Additional UA profileSanitand with concealedmount cistern
Notes
Max partition height UA 50 = 300 m UA 75 = see system data sheet W11de Knauf Metal Stud Partition for the wall heights
Minimum cladding ge 18 mm Knauf Boards recommendation 2x 125 mm Knauf Diamant
Web cutouts are not permissible in UA Sanistand subject to cantilever loads point loads or linear distributed loadsObserve the manufacturersrsquo details for lateral UA profiles and cladding Additional UA profiles are required laterally on Sanistand mounts acc to DIN 18340 section 374 Only possible without additional UA profiles if the manufacturer of the Sanistand base or WC Sanistand permits itDeviating specifications of the Sanistand manufacturer must be considered and observed
17
Loads on partitions and furringsFull-length Sanistand
Notes
Max partition height rear W112de UA 50 = 300 m UA 75 = see system data sheet W11de Knauf Metal Stud Partition for the wall heights
Minimum cladding front wall installations ge 18 mm Knauf Boards recommendation 2x 125 mm Knauf Diamant
Web cutouts are not permissible in UA Sanistand subject to cantilever loads point loads or linear distributed loadsObserve the manufacturersrsquo details for lateral UA profiles and cladding Additional UA profiles are required laterally on Sanistand mounts acc to DIN 18340 section 374 Only possible without additional UA profiles if the manufacturer of the Sanistand base or WC Sanistand permits itDeviating specifications of the Sanistand manufacturer must be considered and observed
Scale 110DetailsW626Vde-V1 Without back anchoring W626Vde-H1 Without back anchoring Vertical section Horizontal section
UW runnerUniflott + Trenn-Fix
UW runner
Additional UA profile
Sanistand withconcealed mount cistern
Knauf connection bracket withenclosed M8 carriage bolt
Knauf connection bracket withenclosed M8 carriage bolt
2x 125 mm DiamantDiamant screw XTB
Knauf sealing tape
Sanistand withconcealed mount cisternKnauf connection bracket with
enclosed M8 carriage bolts
Stud spacing le 625 mm
UW runner
Knauf boardsCW stud
Additional UA profile
18
Loads on partitions and furringsFull-length Sanistand
Scale 110DetailsW626Vde-V2 Back anchoring in traverse W626Vde-H2 Back anchoring in traverse Vertical section Horizontal section
Sanistand withconcealed mount cistern
SealantUD profile made of insulation strips
UW runner
UW runner
UA profile
Knauf multi-purpose screw FN
Uniflott + Trenn-Fix
Multi-purpose traverse 555 300 23 mm
Knauf connection bracket withenclosed M8 carriage bolts
2x 125 mm DiamantDiamant screw XTB
Knauf connection bracket withenclosed M8 carriage bolt
Wall anchor installation acc to WCSanistand manufacturer specifications
Knauf sealing tape
Stud spacing le 625 mm
Multi-purpose traverse555 300 23 mm
UA profile
UA profile
Knauf connection bracket withenclosed M8 carriage bolt
Knauf connectionbracket with enclosedM8 carriage bolt
Wall anchorinstallation acc to
WC Sanistandmanufacturerspecifications
Notes
Max partition height rear W112de UA 50 = 300 m UA 75 = see system data sheet W11de Knauf Metal Stud Partitions for the wall heights
Minimum cladding front wall installations ge 18 mm Knauf Boards recommendation 2x 125 mm Knauf Diamant
Web cutouts are not permissible in UA Sanistand subject to cantilever loads point loads or linear distributed loadsObserve the manufacturersrsquo details for lateral UA profiles and cladding Additional UA profiles are required laterally on Sanistand mounts acc to DIN 18340 section 374 Only possible without additional UA profiles if the manufacturer of the Sanistand base or WC Sanistand permits itDeviating specifications of the Sanistand manufacturer must be considered and observed
19
Loads on partitions and furringsFull-length Sanistand
Scale 110DetailsW626Vde-V3 Back anchoring in UA profile W626Vde-H3 Back anchoring in UA profile Vertical section Horizontal section
Sanistand withconcealed mount cistern
SealantUD profile on insulation strips
UW runner
UW runner
Additional UA profile
Knauf multi-purpose screw FN
Uniflott + Trenn-Fix
UA profile
Knauf connection bracket withenclosed M8 carriage bolts
2x 125 mm DiamantDiamant screw XTB
Knauf connection bracket withenclosed M8 carriage bolts
Fixing bolts with nuts andwashers
Knauf sealing tape
Stud spacing le 625 mm
Additional UA profile
UA profile Fixing bolts with nutsand washers
Knauf connection bracket withenclosed M8 carriage bolts
Knauf connectionbracket with enclosedM8 carriage bolts
Notes
Max partition height at rear W112de UA 50 = 300 m UA 75 = see system data sheet W11de Knauf Metal Stud Partition for the wall heights
Minimum cladding front wall installations ge 18 mm Knauf Boards recommendation 2x 125 mm Knauf Diamant
Web cutouts are not permissible in UA Sanistand subject to cantilever loads point loads or linear distributed loadsObserve the manufacturersrsquo details for lateral UA profiles and cladding Additional UA profiles are required laterally on Sanistand mounts acc to DIN 18340 section 374 Only possible without additional UA profiles if the manufacturer of the Sanistand base or WC Sanistand permits itDeviating specifications of the Sanistand manufacturer must be considered and observed
20
Loads on partitions and furringsFull-length Sanistand
Scale 110DetailsW626Vde-V4 Back anchoring in mounting rail W626Vde-H4 Back anchoring in mounting rail Vertical section Horizontal section
Sanistand withconcealed mount cistern
2x 125 mm Diamant
SealantUD profile on insulation strips
UW runner
Diamant screw XTB
UA profile
Knauf multi-purpose screw FN
Mounting rail with fixing screw
Knauf connection bracket withenclosed M8 carriage bolt
Uniflott + Trenn-Fix
UA profile
Knauf connection bracket withenclosed M8 carriage bolt
Knauf sealing tapeUW runner
Stud spacing le 625 mm
UA profile
UA profile
Mounting railFixing screw
Mounting screw
Sanistand withconcealed mount cistern
Knauf connection bracket withenclosed M8 carriage bolt
Knauf connectionbracket with enclosedM8 carriage bolt
Notes
Max partition height rear W112de UA 50 = 300 m UA 75 = see system data sheet W11de Knauf Metal Stud Partitions for the wall heights
Minimum cladding front wall installations ge 18 mm Knauf Boards recommendation 2x 125 mm Knauf Diamant
Web cutouts are not permissible in UA Sanistand subject to cantilever loads point loads or linear distributed loadsObserve the manufacturersrsquo details for lateral UA profiles and cladding Additional UA profiles are required laterally on Sanistand mounts acc to DIN 18340 section 374 Only possible without additional UA profiles if the manufacturer of the Sanistand base or WC Sanistand permits itDeviating specifications of the Sanistand manufacturer must be considered and observed
21
Notes
In case of load attachment to ldquomulti-level ceiling systemsrdquo refer to the respective valid Knauf system data sheetsIn case of attachment of loads to free-spanning ceilings see system data sheet D13de Knauf Free-Spanning Ceilings
Attachment of loads to Knauf board ceilingsAdditional loads eg lighting fixtures curtain rails and similar can be fixed to Knauf board ceilings using universal dowels cavity dowels spring toggle dowels or Knauf Hartmut Hohlraumduumlbel cavity dowelsAdditional loads must be considered when determining the load class
NoteHeavy loads must be attached directly on load-bearing building elements (basic ceiling) or on auxiliary constructions eg traverses
For each area under load of the Knauf board ceiling the weight of thefastened components may not exceed the following limits
Permissible weight per ceiling area in kgmsup2Without fire resistance With fire resistance1)
15 61)Incaseofapplicationasafireresistanceceilingwithexposedceiling(multi-levelceilingsystem)15kgmsup2totalweightispermissiblefortheexposedceiling(includinginsulationlayerandattachedloads)attachedtothefireresistanceceiling
Furthermore the following conditions applyFor each anchoring point the components fastened to the board ceiling may not exceed the following weights
Fastening method Permissible weight per anchoring point in kgWithout fire resistance With fire resistance
Fastening in the cladding 6 05
Fastening to the grid 10 10
Fastening in the claddingKnauf Hartmut Hohlraumduumlbel cavity dowelScrew M5
Fastening to the gridKnauf Universalschraube FN multi-purpose screw eg curtain rail
The minimum separation spacings between individual attached loads must be observed to avoid local overloading of the ceiling The minimum separation clearance between two attachment points consists of both load radii for the point loadsThe load radius of a point load can be taken from the following diagram in dependence on the permissible weight per unit area for additional loads
Point load in kg
7570656055504540353025201510
0 2 3 4 5 6 7 8 9 10
Radiu
s in c
m
1
50
Fastening in the claddingpossible (without fire resistance)
3 kgmsup2 permissible additional weight (on the exposed ceiling under a fire resistance ceiling refer to the respective valid Knauf system data sheets)6 kgmsup2 permissible additional weight (with fire resistance)15 kgmsup2 permissible additional weight (without fire resistance)
Example fastening scheme at 15 kgmsup2
05 kg
10 kg
3 kgr = 25 cm
r = 46 cm
6 kgr = 355 cm
1 kg
r = 15 cm
r = 105 cm
NoteThe anchored loads can be transferred using several anchoring elements
Loads on board ceilingsFastening in the cladding grid
22
Knauf multi-purpose traversesThe multi-purpose traverse in Knauf board ceilings is suitable for the application of point loads up to 075 kN eg chandeliers music speakers or similarThe multi-purpose traverse consists of a 23 mm thick multi-layer wooden board and galvanized sheet metal profiles It is fastened to the side of the CD furring channelThe attachment of the loads to the traverses should be performed using Knauf Multi-Purpose Screw FNInstallation is possible in a double layer profile grid and flush profile grid
Installation and applicationBend the Daisy chain clip before lateral screw fastening The Daisy chain clip is then Z shaped The unpunched metal side of the Daisy chain clip is pushed onto the lower side of the traverse and then screw fastened laterally through the factory-made hole on the long side of the traverse Screw fasten 4x Daisy chain clips each using one drywall screw TN 35 x 35 about 100 mm from the corner of the multi-layer board on the long edge of the multi-purpose traverse Arrange an additional CD channel (length ge 650 mm) for every long edge in accordance with the width of the multi-purpose traverse Alternately a ceiling furring channel can be used for application of the multi-purpose traverse The supporting profiles are suspended using ceiling suspenders of load class 40 kg The suspenders may not be situated in the direct vicinity of the longitudinal area of the traverse as this will hinder the installation of the traverse Introduce the multi-purpose traverse between the support profiles bend the Daisy chain clip around the CD channel and engage it In case of single-layer cladding do not screw fasten the surface cladding with the multi-purpose traverse
1 Apply the Daisy chain clip 2 Bend the Daisy chain clip 3 Screw fasten the Daisy chain clip
Loads on board ceilingsAnchoring in the traverses
100 mm
23
Loads on board ceilingsAnchoring in the traverses
Scale 110 I Dimensions in mmDetailsD112de SO18 Vertical section ndash Multi-purpose traverse D113de SO12 Vertical section ndash Multi-purpose traverseeg with two additional CD channels I Without fire resistance eg with one additional CD channel I Without fire resistance
D112de SO19 Vertical section ndash Multi-purpose traverse D113de SO13 Vertical section ndash Multi-purpose traverseeg with two additional CD channels I Without fire resistance eg with one additional CD channel I Without fire resistance
D112de SO20 Top view ndash Multi-purpose traverse D113de SO14 Top view ndash Multi-purpose traverseeg with two additional CD channels I Without fire resistance eg with one additional CD channel I Without fire resistance
Fasten Daisy chain clip with drywall screwTN 35 x 35 to multi-purpose traverse
Additional CD channel with two suspendersLoad bearing capacity class ge 040 kN
Multi-purposetraverse555 300 23 mm
300
Furring channel spacing 500
Fasten Daisy chain clip with drywall screwTN 35 x 35 to multi-purpose traverse
Additional suspended load bearing capacity class ge 040 kNMulti-purposetraverse555 300 23 mm
300
Furring channel spacing 500
Additional CD channel with two suspendersLoad bearing capacity class ge 040 kN
Multi-purposetraverse555 300 23 mm
Fasten Daisy chain clip with drywall screwTN 35 x 35 to multi-purpose traverse
Wood panel 555approx
100
Additional suspenderload bearing capacityclass ge 040 kN
Multi-purposetraverse555 300 23 mm
Fasten Daisy chain clip with drywall screwTN 35 x 35 to multi-purpose traverse
Wood panel 555approx
100
Daisy chain clip
Furring channel spacing 500
Traverse
CDchannel
Multi-layerwood panel
Furring channel spacing 500
Multi-purposetraverse
Daisy chain clip
Multi-layerwood panel
Additional grid 4 additional suspension points (eg Nonius suspension)
All technical changes reserved Only the current printed instructions are valid The stated information represents current state-of-the-art Knauf technology The entire state of approved engineering rules appropriate standards guidelines and rules of crafts-manship are not included herewith These and all application instructions have to be adhered to separately by the installer Our warranty is expressly limited to our products in flawless condition All application quantities and delivery amounts are based on empirical data that are not easily transferable to other deviating areasAll rights reserved All amendments reprints and photocopies including those of excerpts require our expressed permission
The stated constructional and structural design specifications and characteristics of building physics of Knauf systems can only be ensured with the exclusive use of Knauf system components or other products expressly recommended by Knauf
Knauf Gips KG Am Bahnhof 7 97346 Iphofen GermanyKnauf DirectTechnical Advisory Service
knauf-direktknaufde
wwwknaufde
VT03deeng09190TI
The iPad App Knauf Infothek now provides all the current information and documents from Knauf Gips KG at any time and in every location in a clear and comfortable wayKnauf Infothek
Videos for Knauf systems and products can be found under the following linkwwwyoutubecomknaufEPD
5
Loads on partitions and furringsCantilever loads
Up to 10 kNm (100 kgm) wall lengthMaximum permissible cabinet weight (kg) acc to table
Cabinet widthmm
Cabinet depthmm100 200 300 400 500 600
400 90 80 70 60 50 40600 135 120 105 90 75 60800 180 160 140 120 100 801000 225 200 175 150 125 1001200 270 240 210 180 150 120
Assume the worst-case value with intermediate values or diagram procedure
orMaximum permissible cabinet weight (kg) acc to diagramMax permissible cabinet weight
kgCabinet width
mm1200
400
1000
600
800
Cabinet depthmm 600100 200 300 400 500
20
140
120
80
40
60
200
160
180
100
240
220
260
280
300
Up to 15 kNm (150 kgm) wall lengthMaximum permissible cabinet weight (kg) acc to table
Cabinet widthmm
Cabinet depthmm100 200 300 400 500 600
400 135 120 105 90 75 60600 202 180 157 135 112 90800 270 240 210 180 150 1201000 337 300 262 225 187 1501200 360 360 315 270 225 180
Assume the worst-case value with intermediate values or diagram procedure
orMaximum permissible cabinet weight (kg) acc to diagram
400
mm
1000
1200
600
800
Max permissible cabinet weight
kgCabinet width
Cabinet depthmm 600500400300200100
20
140
120
80
40
60
200
160
180
100
240
220
260
280
300
320
340
6
Loads on partitions and furringsFastening in the cladding
Fields of applicationAccording to DIN 18183 the metal stud partitions and independent furrings can be loaded at any position by cantilever loads
Up to 04 kNm (40 kgm) wall length Cladding thickness ge 125 mm Knauf boards Up to 07 kNm (70 kgm) wall length Cladding thickness ge 15 mm Diamant (in acc to abP P-140592810) ge 18 mm Knauf boards
With Diamant Steel GKFI and a cover layer ge 125 mm Diamant GKFI (see following table) cantilever loads up to 15 kNm (150 kgm) on walls are possible
Selection of the grid in dependence on the expected loadLoad max Load
typeProfile min Cladding thickness min Furring
possibleLoaded side Unloaded sideKn
auf
Boar
ds
Diam
ant
Diam
ant
Stee
l GKF
I Minimum thickness
Knau
f Bo
ards
Diam
ant
Diam
ant
Stee
l GKF
I Minimum thickness
tmm
tmmkNm2
04 StaticCW 50 125 125 YesCW 50 125 125 Yes
07 StaticCW 50 125 + 04 125 + 04 Yes 2)
CW 75 18 18 Yes 2)
CW 75 15 15 Yes 2)
10 StaticCW 50
125 + 041) + 125 2x 125 Yes
CW 75 125 + 04 125 No
15 Static CW 75 125 + 04
+ 125 2x 125 No
1)ScrewspacingDrywallScrewsXTB1stlayerDiamantSteelGKFIle250mm2)IncaseofapplicationofpartitionheightsacctoDIN18183-1onlycantileverloadsupto04kNmarepossible
Fixing loadsFor fixing of cantilever loads
Dowel screw Maximum screw dowel load capacity in kgX-hooks Knauf Cavity Dowel
HartmutScrew M5
fischer MHD 5 x 65 SScrew M5 or M6
Knauf Multi-Purpose Screw FN 43 x 65
Plastic cavity dowelOslash 8 or 10 mm
Diamant125 mm 5 10 15 40 20 13 3015 18 mm 5 10 15 45 25 14 352x 125 mm 5 10 15 60 30 20 45ge 2x 125 mm 5 10 15 65 35 40 50Diamant Steel GKFI1x 125 + 04 mm 5 10 15 80 50 30 30 3)
2x 125 + 04 mm 5 10 15 100 90 60 55 3)
Measuredwith300mmeccentricity3)ValuesapplywithfischerplasticcavitydowelsUX8x50withKnaufMulti-PurposeScrewFN43x65orequivalent
Notes
Static loads in this respect are permanently fastened loads such as towel rails cabinets shelves and boilers Dynamic loads are exerted by fastened components which are subjected to continuous changes in load such as handrails fold-down seats and folding handles The use of traverses is required here see page 8Always screw fasten Diamant Steel GKFI with Diamant Screws XTB even for a cover layer of Diamant
7
Loads on partitions and furringsAnchoring in the cladding
RatingThe specified permissible cantilever loads are in accordance with the DIN 18183 or DIN 4103-1 at an eccentricity (spacing of resulting load to the wall surface) of max 300 mm The permissible load is reduced accordingly with greater eccentricity The determination of the permissible cantilever loads with divergent eccentricity is undertaken using the tables or diagrams on page 4 and page 5
Rating examples Determination of the permissible cabinet weight as well as the required minimum number of dowels (always ge 2)Metal stud partition W111de CW 50 cladding 125 mm Diamant GKFI acc to tableField of application static load max cantilever load 04 kNm (40 kgm) wall length Cabinet
widthCabinet depthmm
mm 100 200 300 400 500 600
400 31 28 25 22 19 16
600 465 42 375 33 285 24
800 62 56 50 44 38 32
1000 775 70 625 55 475 40
1200 93 84 75 66 57 48
Cabinet depth 400 mm cabinet width 1000 mm Max cabinet weight 55 kg
Cladding thickness 125 mm plastic cavity dowel
Max dowel load 30 kg
Required number of dowels 55 kg 30 kg = 18 2 dowels
are the min necessary
Metal stud partition W111de CW 75 cladding 2x 125 mm Diamant GKFI acc to diagramField of application static load max cantilever load 07 kNm (70 kgm) wall length
400
mm12001000
600
100 200 400 500 600mm
10
70
60
40
20 30
kg
100
80 90
110120
800
300
50
1
23
450
65
Cabinet depth
Cabinet width
Max permissible cabinet weightCabinet depth 450 mm cabinet width 800 mm
With cabinet depth 450 mm 1 vertically upwards up to the cabinet width line 800 mm
2 at the intersection point horizontal to the left ndash read off value 3
Max cabinet weight 65 kg
Cladding thickness 2x 125 mm Knauf Cavity Dowel Hartmut
Max dowel load 60 kg
Required number of dowels 65 kg 60 kg = 108 2 dowels
are the min necessary
8
Fields of applicationTraverses are built-in elements in lightweight partitions that transfer the fastening loads directly into the grid or into the flanking solid constructions
Selection of the traverse and grid in dependence on the expected loadFastening Load max Load type Profile min Cladding thickness min Independent
furring possible
Knauf Boards DiamantkNm2 mm mm
Steel anchoring traversesee page 14
07 Static CW 50 125 125 No07 Static CW 50 18 15 Yes10 Static CW 75 125 125 No10 Static CW 50 18 15 Yes
Metal traverse with gypsum fibre insertsee page 12
07 Static CW 50 125 125 No07 Static CW 50 18 15 Yes10 Static CW 75 125 125 No10 Static CW 50 18 15 Yes15 Static CW 50 18 15 No15 Static UA 50 18 15 Yes15 Dynamic UA 75 18 15 Yes
Multi-purpose traversesee page 10
07 Static CW 50 125 125 No07 Static CW 50 18 15 Yes10 Static CW 75 125 125 No10 Static CW 50 18 15 Yes15 Static CW 50 18 15 No15 Static UA 50 18 15 Yes15 Dynamic UA 75 18 15 Yes
Fixing loadsFor fixing of cantilever loads
Dowel screw Maximum screw dowel load capacity in kgKnauf Cavity Dowel Hartmut
fischer MHD 5 x 65 S
Knauf Multi- Purpose Screw FN 43 x 65
fischer plastic cavity dowels 8 x 50 with Knauf Multi-Purpose Screw FN 43 x 65
Wood screw Oslash 50 mm
Wood screw Oslash 60 mm
TraversesSteel anchoring traverse 75 ndash 45 40 45 45
Metal traversewith gypsum fibre insert
90 75 65 46 55 70
Multi-purpose traverse ndash ndash 125 ndash 115 165
Measuredwith300mmeccentricity
Loads on partitions and furringsAnchoring in the traverses
NotesStatic loads in this respect are permanently fastened loads such as towel rails cabinets shelves and boilers Dynamic loads are exerted by fastened components which are subjected to continuous changes in load such as handrails fold-down seats and folding handles
9
Loads on partitions and furringsAnchoring in the traverses
RatingThe specified permissible cantilever loads are in accordance with the DIN 18183 or DIN 4103-1 at an eccentricity (spacing of resulting load to the wall surface) of max 300 mm The permissible load is reduced accordingly with greater eccentricity The determination of the permissible cantilever loads with divergent eccentricity is undertaken using the tables or diagrams on page 4 and page 5
Rating examples Determination of the permissible cabinet weight as well as the required minimum number of dowels (always ge 2)Metal stud partition W111de CW 50 cladding 18 mm Knauf board acc to tableField of application static load max cantilever load 07 kNm (70 kgm) wall length Cabinet
widthCabinet depthmm
mm 100 200 300 400 500 600400 43 40 37 34 31 28600 645 60 555 51 465 42800 86 80 74 68 62 561000 1075 100 925 85 775 701200 129 120 111 102 93 84
Cabinet depth 500 mm cabinet width 800 mm Max cabinet weight 62 kg Fixing traverse Knauf Multi-Purpose Screw FN 43 x 65
Max screw load 45 kg
Required number of screws 62 kg 45 kg = 14 2 screws
are the min necessary
Metal stud partition W111de UA 75 cladding 15 mm Diamant GKFI acc to diagram
Field of application dynamic load max cantilever load 15 kNm (150 kgm) wall length
20
400
Cabinet depth100 200 600
Max permissible cabinet weight
140120
80
4060
kg
200
160
180
Cabinet width
mm
1000
1200
600
mm 300
100 800
240220
260280300320340
450400 500
165
1
23
Cabinet depth 450 mm cabinet width 800 mm
With cabinet depth 450 mm 1 vertically upwards up to the cabinet width line 800 mm
2 at the intersection point horizontal to the left read off value 3
Max cabinet weight 165 kg
Multi-purpose traverse Knauf Multi-Purpose Screw FN 43 x 65
Max screw load 125 kg
Required number of screws 165 kg 125 kg = 13 2 screws
are the min necessary
10
Knauf multi-purpose traversesThe multi-purpose traverse is suitable for accepting loads attached to the wall up to 15 kNm wall length eg cupboards boilers folding wall attached seats folding handles and similarThe multi-purpose traverse consists of a 23 mm thick multi-layer wooden board and galvanized sheet metal profiles It is fastened to the side of the floor-to-ceiling profilesThe attachment of the loads to the traverses should be performed using Knauf Multi-Purpose Screw FN
NoteTraverses for installation in damp and wet rooms see also system data sheet W38de Knauf Metal Stud Partitions AQUAPANELreg
Loads on partitions and furringsAnchoring in the traverses
Installation and applicationMulti-purpose traverse made of multi-layer wooden board and galvanized sheet metal profiles attached to the side of the CW studs UA profiles For CW studs screw fasten using the 6 enclosed Metal Screws LN 35 x 11 mm (3 per side) For UA profiles screw fasten with the 6 enclosed Drilling Screws ST 42 x 13 mm (3 per side)Arrangement in a rowUA profiles CW studs
Direction of installation Direction of installation
11
Loads on partitions and furringsAnchoring in the traverses
W234de-A10 View ndash Design with UA profile W234de-A13 View ndash Design with CW stud
W234de-H10 Horizontal section ndash Design with UA profile W234de-H13 Horizontal section ndash Design with CW studeg W626de eg W626de
W234de-V10 Vertical section ndash Design with UA profile W234de-V13 Vertical section ndash Design with CW studeg W116de eg W112de
Wooden board 555
Stud spacing 625 (grid dimension)
300
Multi-purpose traverse555 300 23 mm
Multi-layer wooden board
UA profile
Drillingscrew ST42 x 13(enclosed)
Wooden board 555
Stud spacing 625 (grid dimension)
300 Metal screw
LN 35 x 11(enclosed)
Multi-purpose traverse555 300 23 mm
Multi-layer wooden board
CW stud
Wooden board 555
Stud spacing 625 (grid dimension)
300
Multi-purpose traverse555 300 23 mm
UA profileDrilling screwST 42 x 13
Multi-purpose traverse555 300 23 mm
CW studMetal screwLN 35 x 11
48
eg folding wallattached seat
Knauf boardstrips
eg Supporthandle maxprojection 800 mm
Multi-purposetraverseUA profileKnauf boards
48
Multi-purposetraverseCW studKnauf boards
eg Cabinet
Scale 110 I Dimensions in mmDetails
Note No web cutouts in the CW studs are permissible for traverses to which the CW studs are attached
12
Knauf steel anchoring traverse with gypsum fibre insertThe steel anchoring traverse with gypsum fibre insert is suitable for accepting loads attached to the wall up to 15 kNm wall length eg cupboards shelves handrails and similarThe metal traverse with gypsum fibre insert consists of 075 mm thick sheet metal as well as an 18 mm thick gypsum fibre board It is fastened to the side of the floor-to-ceiling profiles The attachment of the loads to the traverses should be performed using Knauf Multi-Purpose Screw FNUse in partition systems where the requirement for non-combustible reaction to fire exists
Installation and applicationSteel anchoring traverse made of galvanized steel with gypsum fibre insert fastened to the CW studs UA profiles In case of CW studs crimp using a Stud Crimper and for UA profiles screw fasten with 6 Drilling screws LB 35 x 16 mmArrangement in a rowUA profiles CW studs
Loads on partitions and furringsAnchoring in the traverses
13
Scale 110 I Dimensions in mmDetailsW234de-A12 View - Design with UA profile W234de-A14 View - Design with CW stud
W234de-H12 Horizontal section - Design with UA profile W234de-H14 Horizontal section - Design with CW studeg W112de eg W112de
W234de-V12 Vertical section - Design with UA profile W234de-V14 Vertical section - Design with CW studeg W112de eg W112de
Traverse dimension 620
Stud spacing 625 (grid dimension)
290
Steel anchoring traversewith gypsum fibre insert
Traverse attached to UA profileusing drilling screws
UA profile
Steel anchoring traversewith gypsum fibre insert
CW stud
Crimp the traverse to the CW studusing a stud crimper
Traverse dimension 620
Stud spacing 625 (grid dimension)
290
Drilling screwLB 35 x 16
Steel anchoringtraverse with gypsum
fibre insert
UA profile Crimped Steel anchoring traversewith gypsum fibre insert
CW stud
eg Handrail
UA profileKnauf boards
Steel anchoring traversewith gypsum fibre insert
eg Handrail
CW studKnauf board
Steel anchoring traversewith gypsum fibre insert
Loads on partitions and furringsAnchoring in the traverses
Note No web cutouts in the CW studs are permissible for traverses to which the CW studs are attached
14
Loads on partitions and furringsAnchoring in the traverses
Knauf steel anchoring traverseThe steel anchoring traverse is suitable for accepting loads attached to the wall up to 10 kNm wall length eg towel holders cupboards shelves and similar Not suitable for dynamic loads such as folding wall attached seatsThe steel anchoring traverse consists of 075 mm thick sheet metal and are crimped onto the side using a stud crimper on the CW studs Particularly suitable for single-layer clad metal stud partitions and furrings where in case of cantilever loads gt 04 kNm (400 kgm) wall length the installation of a traverse is required
NoteTraverses for installation in damp and wet rooms see also system data sheet W38de Knauf Metal Stud Partitions AQUAPANELreg
Installation and applicationCrimp the steel anchoring traverse made of galvanized sheet steel to the CW studs using a Stud CrimperAdditional screw fastening of the steel anchoring traverse via screw fastening of the cladding (min 2 to 3 anchoring points) Reduce the screw spacing of the cladding if necessaryArrangement in a rowCW studs
Scale 110 I Dimensions in mmDetailsW234de-A11 View W234de V11 Vertical section
eg W111de
W234de-H11 Horizontal sectioneg W111de
Sheet metal gauge 075 mm
Steel anchoring traverse
CW stud
Crimp the traverse to the CW studusing the stud crimper
290
Traverse dimension 620
Stud spacing 625 (grid dimension)
eg Cabinet
CW stud
Knauf boardSteel anchoring traverse
Steel anchoring traverseCW stud
Crimped
Note No web cutouts in the CW studs are permissible for traverses to which the CW studs are attached
15
Full-length SanistandFloor-to-ceiling Sanistands made of galvanized UA profiles (min UA 75) 2 mm thick are suitable for transferring loads from traverses into the supporting structure or for fixing loads hanging onto walls such as school blackboards up to 15 kNm wall lengthFloor-to-ceiling Sanistands profiles are anchored to the basic floor and ceiling with door frame brackets or connection brackets for UA profiles The upper door frame bracket includes openings for routing cables such as pipe-in-pipe systems or electrical cablesThe loads are connected directly to the flange of the UA profile
W228de-A10 View
le 1000 mm
UW runnercontinuous
Door frameconnection brackettop connection withenclosed dowels
CW studAxial spacing suitedto partition system
UA profileas afloor-to-ceilingSanistand forbearing cantileverloads
UW runnercontinuous
Door frameconnection bracketbottom connectionwith enclosed dowels
Scale 110
Installation and applicationFloor-to-ceiling Sanistands made of UA profiles must be anchored to the basic floor and ceiling with door frame brackets or connection brackets for UA profiles The upper door frame bracket includes openings for routing cables such as pipe-in-pipe systems or electrical cables Fasten objects to UA profiles using threaded rods U washers and M1012 steel nuts or self-tapping screws
Loads on partitions and furringsFull-length Sanistand
Detail
Notes
Web cutouts are not permissible in UA Sanistand subject to cantilever loads point loads or linear distributed loadsMaximum screw load with connections to full height Sanistand (UA profile)Every UA profile flange and anchoring point may not exceed a resulting pull-out load of 150 kN (150 kg)Components similar to cantilevers such as foldable rails should be screwed onto two adjacent UA profilesUse suitable drilling screws eg Ejot Zebra Piasta Hilti S-MD or comparable
16
Loads on partitions and furringsFull-length Sanistand
Scale 110DetailsW116de-V1 Sanistand W116de-H1 SanistandVertical section I Without fire resistance Horizontal section I Without fire resistance
UW runnerUniflott + Trenn-Fix
UW runner
Additional UA profile
Sanistand withconcealed mount cistern
Knauf connectionbracket with enclosedM8 carriage bolts
Knauf conection bracket withenclosed M8 carriage bolt
2x 125 mm DiamantDiamant screw XTB
Additional CW stud
Knauf sealing tape
Board strip installationacc to W11de systemdata sheet
Stud spacing le 625 mm
CW stud profile
Additional CW studBoard strip installation in acc with W11de system data sheet
Knauf connection bracket withenclosed M8 carriage bolts
Additional UA profileSanitand with concealedmount cistern
Notes
Max partition height UA 50 = 300 m UA 75 = see system data sheet W11de Knauf Metal Stud Partition for the wall heights
Minimum cladding ge 18 mm Knauf Boards recommendation 2x 125 mm Knauf Diamant
Web cutouts are not permissible in UA Sanistand subject to cantilever loads point loads or linear distributed loadsObserve the manufacturersrsquo details for lateral UA profiles and cladding Additional UA profiles are required laterally on Sanistand mounts acc to DIN 18340 section 374 Only possible without additional UA profiles if the manufacturer of the Sanistand base or WC Sanistand permits itDeviating specifications of the Sanistand manufacturer must be considered and observed
17
Loads on partitions and furringsFull-length Sanistand
Notes
Max partition height rear W112de UA 50 = 300 m UA 75 = see system data sheet W11de Knauf Metal Stud Partition for the wall heights
Minimum cladding front wall installations ge 18 mm Knauf Boards recommendation 2x 125 mm Knauf Diamant
Web cutouts are not permissible in UA Sanistand subject to cantilever loads point loads or linear distributed loadsObserve the manufacturersrsquo details for lateral UA profiles and cladding Additional UA profiles are required laterally on Sanistand mounts acc to DIN 18340 section 374 Only possible without additional UA profiles if the manufacturer of the Sanistand base or WC Sanistand permits itDeviating specifications of the Sanistand manufacturer must be considered and observed
Scale 110DetailsW626Vde-V1 Without back anchoring W626Vde-H1 Without back anchoring Vertical section Horizontal section
UW runnerUniflott + Trenn-Fix
UW runner
Additional UA profile
Sanistand withconcealed mount cistern
Knauf connection bracket withenclosed M8 carriage bolt
Knauf connection bracket withenclosed M8 carriage bolt
2x 125 mm DiamantDiamant screw XTB
Knauf sealing tape
Sanistand withconcealed mount cisternKnauf connection bracket with
enclosed M8 carriage bolts
Stud spacing le 625 mm
UW runner
Knauf boardsCW stud
Additional UA profile
18
Loads on partitions and furringsFull-length Sanistand
Scale 110DetailsW626Vde-V2 Back anchoring in traverse W626Vde-H2 Back anchoring in traverse Vertical section Horizontal section
Sanistand withconcealed mount cistern
SealantUD profile made of insulation strips
UW runner
UW runner
UA profile
Knauf multi-purpose screw FN
Uniflott + Trenn-Fix
Multi-purpose traverse 555 300 23 mm
Knauf connection bracket withenclosed M8 carriage bolts
2x 125 mm DiamantDiamant screw XTB
Knauf connection bracket withenclosed M8 carriage bolt
Wall anchor installation acc to WCSanistand manufacturer specifications
Knauf sealing tape
Stud spacing le 625 mm
Multi-purpose traverse555 300 23 mm
UA profile
UA profile
Knauf connection bracket withenclosed M8 carriage bolt
Knauf connectionbracket with enclosedM8 carriage bolt
Wall anchorinstallation acc to
WC Sanistandmanufacturerspecifications
Notes
Max partition height rear W112de UA 50 = 300 m UA 75 = see system data sheet W11de Knauf Metal Stud Partitions for the wall heights
Minimum cladding front wall installations ge 18 mm Knauf Boards recommendation 2x 125 mm Knauf Diamant
Web cutouts are not permissible in UA Sanistand subject to cantilever loads point loads or linear distributed loadsObserve the manufacturersrsquo details for lateral UA profiles and cladding Additional UA profiles are required laterally on Sanistand mounts acc to DIN 18340 section 374 Only possible without additional UA profiles if the manufacturer of the Sanistand base or WC Sanistand permits itDeviating specifications of the Sanistand manufacturer must be considered and observed
19
Loads on partitions and furringsFull-length Sanistand
Scale 110DetailsW626Vde-V3 Back anchoring in UA profile W626Vde-H3 Back anchoring in UA profile Vertical section Horizontal section
Sanistand withconcealed mount cistern
SealantUD profile on insulation strips
UW runner
UW runner
Additional UA profile
Knauf multi-purpose screw FN
Uniflott + Trenn-Fix
UA profile
Knauf connection bracket withenclosed M8 carriage bolts
2x 125 mm DiamantDiamant screw XTB
Knauf connection bracket withenclosed M8 carriage bolts
Fixing bolts with nuts andwashers
Knauf sealing tape
Stud spacing le 625 mm
Additional UA profile
UA profile Fixing bolts with nutsand washers
Knauf connection bracket withenclosed M8 carriage bolts
Knauf connectionbracket with enclosedM8 carriage bolts
Notes
Max partition height at rear W112de UA 50 = 300 m UA 75 = see system data sheet W11de Knauf Metal Stud Partition for the wall heights
Minimum cladding front wall installations ge 18 mm Knauf Boards recommendation 2x 125 mm Knauf Diamant
Web cutouts are not permissible in UA Sanistand subject to cantilever loads point loads or linear distributed loadsObserve the manufacturersrsquo details for lateral UA profiles and cladding Additional UA profiles are required laterally on Sanistand mounts acc to DIN 18340 section 374 Only possible without additional UA profiles if the manufacturer of the Sanistand base or WC Sanistand permits itDeviating specifications of the Sanistand manufacturer must be considered and observed
20
Loads on partitions and furringsFull-length Sanistand
Scale 110DetailsW626Vde-V4 Back anchoring in mounting rail W626Vde-H4 Back anchoring in mounting rail Vertical section Horizontal section
Sanistand withconcealed mount cistern
2x 125 mm Diamant
SealantUD profile on insulation strips
UW runner
Diamant screw XTB
UA profile
Knauf multi-purpose screw FN
Mounting rail with fixing screw
Knauf connection bracket withenclosed M8 carriage bolt
Uniflott + Trenn-Fix
UA profile
Knauf connection bracket withenclosed M8 carriage bolt
Knauf sealing tapeUW runner
Stud spacing le 625 mm
UA profile
UA profile
Mounting railFixing screw
Mounting screw
Sanistand withconcealed mount cistern
Knauf connection bracket withenclosed M8 carriage bolt
Knauf connectionbracket with enclosedM8 carriage bolt
Notes
Max partition height rear W112de UA 50 = 300 m UA 75 = see system data sheet W11de Knauf Metal Stud Partitions for the wall heights
Minimum cladding front wall installations ge 18 mm Knauf Boards recommendation 2x 125 mm Knauf Diamant
Web cutouts are not permissible in UA Sanistand subject to cantilever loads point loads or linear distributed loadsObserve the manufacturersrsquo details for lateral UA profiles and cladding Additional UA profiles are required laterally on Sanistand mounts acc to DIN 18340 section 374 Only possible without additional UA profiles if the manufacturer of the Sanistand base or WC Sanistand permits itDeviating specifications of the Sanistand manufacturer must be considered and observed
21
Notes
In case of load attachment to ldquomulti-level ceiling systemsrdquo refer to the respective valid Knauf system data sheetsIn case of attachment of loads to free-spanning ceilings see system data sheet D13de Knauf Free-Spanning Ceilings
Attachment of loads to Knauf board ceilingsAdditional loads eg lighting fixtures curtain rails and similar can be fixed to Knauf board ceilings using universal dowels cavity dowels spring toggle dowels or Knauf Hartmut Hohlraumduumlbel cavity dowelsAdditional loads must be considered when determining the load class
NoteHeavy loads must be attached directly on load-bearing building elements (basic ceiling) or on auxiliary constructions eg traverses
For each area under load of the Knauf board ceiling the weight of thefastened components may not exceed the following limits
Permissible weight per ceiling area in kgmsup2Without fire resistance With fire resistance1)
15 61)Incaseofapplicationasafireresistanceceilingwithexposedceiling(multi-levelceilingsystem)15kgmsup2totalweightispermissiblefortheexposedceiling(includinginsulationlayerandattachedloads)attachedtothefireresistanceceiling
Furthermore the following conditions applyFor each anchoring point the components fastened to the board ceiling may not exceed the following weights
Fastening method Permissible weight per anchoring point in kgWithout fire resistance With fire resistance
Fastening in the cladding 6 05
Fastening to the grid 10 10
Fastening in the claddingKnauf Hartmut Hohlraumduumlbel cavity dowelScrew M5
Fastening to the gridKnauf Universalschraube FN multi-purpose screw eg curtain rail
The minimum separation spacings between individual attached loads must be observed to avoid local overloading of the ceiling The minimum separation clearance between two attachment points consists of both load radii for the point loadsThe load radius of a point load can be taken from the following diagram in dependence on the permissible weight per unit area for additional loads
Point load in kg
7570656055504540353025201510
0 2 3 4 5 6 7 8 9 10
Radiu
s in c
m
1
50
Fastening in the claddingpossible (without fire resistance)
3 kgmsup2 permissible additional weight (on the exposed ceiling under a fire resistance ceiling refer to the respective valid Knauf system data sheets)6 kgmsup2 permissible additional weight (with fire resistance)15 kgmsup2 permissible additional weight (without fire resistance)
Example fastening scheme at 15 kgmsup2
05 kg
10 kg
3 kgr = 25 cm
r = 46 cm
6 kgr = 355 cm
1 kg
r = 15 cm
r = 105 cm
NoteThe anchored loads can be transferred using several anchoring elements
Loads on board ceilingsFastening in the cladding grid
22
Knauf multi-purpose traversesThe multi-purpose traverse in Knauf board ceilings is suitable for the application of point loads up to 075 kN eg chandeliers music speakers or similarThe multi-purpose traverse consists of a 23 mm thick multi-layer wooden board and galvanized sheet metal profiles It is fastened to the side of the CD furring channelThe attachment of the loads to the traverses should be performed using Knauf Multi-Purpose Screw FNInstallation is possible in a double layer profile grid and flush profile grid
Installation and applicationBend the Daisy chain clip before lateral screw fastening The Daisy chain clip is then Z shaped The unpunched metal side of the Daisy chain clip is pushed onto the lower side of the traverse and then screw fastened laterally through the factory-made hole on the long side of the traverse Screw fasten 4x Daisy chain clips each using one drywall screw TN 35 x 35 about 100 mm from the corner of the multi-layer board on the long edge of the multi-purpose traverse Arrange an additional CD channel (length ge 650 mm) for every long edge in accordance with the width of the multi-purpose traverse Alternately a ceiling furring channel can be used for application of the multi-purpose traverse The supporting profiles are suspended using ceiling suspenders of load class 40 kg The suspenders may not be situated in the direct vicinity of the longitudinal area of the traverse as this will hinder the installation of the traverse Introduce the multi-purpose traverse between the support profiles bend the Daisy chain clip around the CD channel and engage it In case of single-layer cladding do not screw fasten the surface cladding with the multi-purpose traverse
1 Apply the Daisy chain clip 2 Bend the Daisy chain clip 3 Screw fasten the Daisy chain clip
Loads on board ceilingsAnchoring in the traverses
100 mm
23
Loads on board ceilingsAnchoring in the traverses
Scale 110 I Dimensions in mmDetailsD112de SO18 Vertical section ndash Multi-purpose traverse D113de SO12 Vertical section ndash Multi-purpose traverseeg with two additional CD channels I Without fire resistance eg with one additional CD channel I Without fire resistance
D112de SO19 Vertical section ndash Multi-purpose traverse D113de SO13 Vertical section ndash Multi-purpose traverseeg with two additional CD channels I Without fire resistance eg with one additional CD channel I Without fire resistance
D112de SO20 Top view ndash Multi-purpose traverse D113de SO14 Top view ndash Multi-purpose traverseeg with two additional CD channels I Without fire resistance eg with one additional CD channel I Without fire resistance
Fasten Daisy chain clip with drywall screwTN 35 x 35 to multi-purpose traverse
Additional CD channel with two suspendersLoad bearing capacity class ge 040 kN
Multi-purposetraverse555 300 23 mm
300
Furring channel spacing 500
Fasten Daisy chain clip with drywall screwTN 35 x 35 to multi-purpose traverse
Additional suspended load bearing capacity class ge 040 kNMulti-purposetraverse555 300 23 mm
300
Furring channel spacing 500
Additional CD channel with two suspendersLoad bearing capacity class ge 040 kN
Multi-purposetraverse555 300 23 mm
Fasten Daisy chain clip with drywall screwTN 35 x 35 to multi-purpose traverse
Wood panel 555approx
100
Additional suspenderload bearing capacityclass ge 040 kN
Multi-purposetraverse555 300 23 mm
Fasten Daisy chain clip with drywall screwTN 35 x 35 to multi-purpose traverse
Wood panel 555approx
100
Daisy chain clip
Furring channel spacing 500
Traverse
CDchannel
Multi-layerwood panel
Furring channel spacing 500
Multi-purposetraverse
Daisy chain clip
Multi-layerwood panel
Additional grid 4 additional suspension points (eg Nonius suspension)
All technical changes reserved Only the current printed instructions are valid The stated information represents current state-of-the-art Knauf technology The entire state of approved engineering rules appropriate standards guidelines and rules of crafts-manship are not included herewith These and all application instructions have to be adhered to separately by the installer Our warranty is expressly limited to our products in flawless condition All application quantities and delivery amounts are based on empirical data that are not easily transferable to other deviating areasAll rights reserved All amendments reprints and photocopies including those of excerpts require our expressed permission
The stated constructional and structural design specifications and characteristics of building physics of Knauf systems can only be ensured with the exclusive use of Knauf system components or other products expressly recommended by Knauf
Knauf Gips KG Am Bahnhof 7 97346 Iphofen GermanyKnauf DirectTechnical Advisory Service
knauf-direktknaufde
wwwknaufde
VT03deeng09190TI
The iPad App Knauf Infothek now provides all the current information and documents from Knauf Gips KG at any time and in every location in a clear and comfortable wayKnauf Infothek
Videos for Knauf systems and products can be found under the following linkwwwyoutubecomknaufEPD
6
Loads on partitions and furringsFastening in the cladding
Fields of applicationAccording to DIN 18183 the metal stud partitions and independent furrings can be loaded at any position by cantilever loads
Up to 04 kNm (40 kgm) wall length Cladding thickness ge 125 mm Knauf boards Up to 07 kNm (70 kgm) wall length Cladding thickness ge 15 mm Diamant (in acc to abP P-140592810) ge 18 mm Knauf boards
With Diamant Steel GKFI and a cover layer ge 125 mm Diamant GKFI (see following table) cantilever loads up to 15 kNm (150 kgm) on walls are possible
Selection of the grid in dependence on the expected loadLoad max Load
typeProfile min Cladding thickness min Furring
possibleLoaded side Unloaded sideKn
auf
Boar
ds
Diam
ant
Diam
ant
Stee
l GKF
I Minimum thickness
Knau
f Bo
ards
Diam
ant
Diam
ant
Stee
l GKF
I Minimum thickness
tmm
tmmkNm2
04 StaticCW 50 125 125 YesCW 50 125 125 Yes
07 StaticCW 50 125 + 04 125 + 04 Yes 2)
CW 75 18 18 Yes 2)
CW 75 15 15 Yes 2)
10 StaticCW 50
125 + 041) + 125 2x 125 Yes
CW 75 125 + 04 125 No
15 Static CW 75 125 + 04
+ 125 2x 125 No
1)ScrewspacingDrywallScrewsXTB1stlayerDiamantSteelGKFIle250mm2)IncaseofapplicationofpartitionheightsacctoDIN18183-1onlycantileverloadsupto04kNmarepossible
Fixing loadsFor fixing of cantilever loads
Dowel screw Maximum screw dowel load capacity in kgX-hooks Knauf Cavity Dowel
HartmutScrew M5
fischer MHD 5 x 65 SScrew M5 or M6
Knauf Multi-Purpose Screw FN 43 x 65
Plastic cavity dowelOslash 8 or 10 mm
Diamant125 mm 5 10 15 40 20 13 3015 18 mm 5 10 15 45 25 14 352x 125 mm 5 10 15 60 30 20 45ge 2x 125 mm 5 10 15 65 35 40 50Diamant Steel GKFI1x 125 + 04 mm 5 10 15 80 50 30 30 3)
2x 125 + 04 mm 5 10 15 100 90 60 55 3)
Measuredwith300mmeccentricity3)ValuesapplywithfischerplasticcavitydowelsUX8x50withKnaufMulti-PurposeScrewFN43x65orequivalent
Notes
Static loads in this respect are permanently fastened loads such as towel rails cabinets shelves and boilers Dynamic loads are exerted by fastened components which are subjected to continuous changes in load such as handrails fold-down seats and folding handles The use of traverses is required here see page 8Always screw fasten Diamant Steel GKFI with Diamant Screws XTB even for a cover layer of Diamant
7
Loads on partitions and furringsAnchoring in the cladding
RatingThe specified permissible cantilever loads are in accordance with the DIN 18183 or DIN 4103-1 at an eccentricity (spacing of resulting load to the wall surface) of max 300 mm The permissible load is reduced accordingly with greater eccentricity The determination of the permissible cantilever loads with divergent eccentricity is undertaken using the tables or diagrams on page 4 and page 5
Rating examples Determination of the permissible cabinet weight as well as the required minimum number of dowels (always ge 2)Metal stud partition W111de CW 50 cladding 125 mm Diamant GKFI acc to tableField of application static load max cantilever load 04 kNm (40 kgm) wall length Cabinet
widthCabinet depthmm
mm 100 200 300 400 500 600
400 31 28 25 22 19 16
600 465 42 375 33 285 24
800 62 56 50 44 38 32
1000 775 70 625 55 475 40
1200 93 84 75 66 57 48
Cabinet depth 400 mm cabinet width 1000 mm Max cabinet weight 55 kg
Cladding thickness 125 mm plastic cavity dowel
Max dowel load 30 kg
Required number of dowels 55 kg 30 kg = 18 2 dowels
are the min necessary
Metal stud partition W111de CW 75 cladding 2x 125 mm Diamant GKFI acc to diagramField of application static load max cantilever load 07 kNm (70 kgm) wall length
400
mm12001000
600
100 200 400 500 600mm
10
70
60
40
20 30
kg
100
80 90
110120
800
300
50
1
23
450
65
Cabinet depth
Cabinet width
Max permissible cabinet weightCabinet depth 450 mm cabinet width 800 mm
With cabinet depth 450 mm 1 vertically upwards up to the cabinet width line 800 mm
2 at the intersection point horizontal to the left ndash read off value 3
Max cabinet weight 65 kg
Cladding thickness 2x 125 mm Knauf Cavity Dowel Hartmut
Max dowel load 60 kg
Required number of dowels 65 kg 60 kg = 108 2 dowels
are the min necessary
8
Fields of applicationTraverses are built-in elements in lightweight partitions that transfer the fastening loads directly into the grid or into the flanking solid constructions
Selection of the traverse and grid in dependence on the expected loadFastening Load max Load type Profile min Cladding thickness min Independent
furring possible
Knauf Boards DiamantkNm2 mm mm
Steel anchoring traversesee page 14
07 Static CW 50 125 125 No07 Static CW 50 18 15 Yes10 Static CW 75 125 125 No10 Static CW 50 18 15 Yes
Metal traverse with gypsum fibre insertsee page 12
07 Static CW 50 125 125 No07 Static CW 50 18 15 Yes10 Static CW 75 125 125 No10 Static CW 50 18 15 Yes15 Static CW 50 18 15 No15 Static UA 50 18 15 Yes15 Dynamic UA 75 18 15 Yes
Multi-purpose traversesee page 10
07 Static CW 50 125 125 No07 Static CW 50 18 15 Yes10 Static CW 75 125 125 No10 Static CW 50 18 15 Yes15 Static CW 50 18 15 No15 Static UA 50 18 15 Yes15 Dynamic UA 75 18 15 Yes
Fixing loadsFor fixing of cantilever loads
Dowel screw Maximum screw dowel load capacity in kgKnauf Cavity Dowel Hartmut
fischer MHD 5 x 65 S
Knauf Multi- Purpose Screw FN 43 x 65
fischer plastic cavity dowels 8 x 50 with Knauf Multi-Purpose Screw FN 43 x 65
Wood screw Oslash 50 mm
Wood screw Oslash 60 mm
TraversesSteel anchoring traverse 75 ndash 45 40 45 45
Metal traversewith gypsum fibre insert
90 75 65 46 55 70
Multi-purpose traverse ndash ndash 125 ndash 115 165
Measuredwith300mmeccentricity
Loads on partitions and furringsAnchoring in the traverses
NotesStatic loads in this respect are permanently fastened loads such as towel rails cabinets shelves and boilers Dynamic loads are exerted by fastened components which are subjected to continuous changes in load such as handrails fold-down seats and folding handles
9
Loads on partitions and furringsAnchoring in the traverses
RatingThe specified permissible cantilever loads are in accordance with the DIN 18183 or DIN 4103-1 at an eccentricity (spacing of resulting load to the wall surface) of max 300 mm The permissible load is reduced accordingly with greater eccentricity The determination of the permissible cantilever loads with divergent eccentricity is undertaken using the tables or diagrams on page 4 and page 5
Rating examples Determination of the permissible cabinet weight as well as the required minimum number of dowels (always ge 2)Metal stud partition W111de CW 50 cladding 18 mm Knauf board acc to tableField of application static load max cantilever load 07 kNm (70 kgm) wall length Cabinet
widthCabinet depthmm
mm 100 200 300 400 500 600400 43 40 37 34 31 28600 645 60 555 51 465 42800 86 80 74 68 62 561000 1075 100 925 85 775 701200 129 120 111 102 93 84
Cabinet depth 500 mm cabinet width 800 mm Max cabinet weight 62 kg Fixing traverse Knauf Multi-Purpose Screw FN 43 x 65
Max screw load 45 kg
Required number of screws 62 kg 45 kg = 14 2 screws
are the min necessary
Metal stud partition W111de UA 75 cladding 15 mm Diamant GKFI acc to diagram
Field of application dynamic load max cantilever load 15 kNm (150 kgm) wall length
20
400
Cabinet depth100 200 600
Max permissible cabinet weight
140120
80
4060
kg
200
160
180
Cabinet width
mm
1000
1200
600
mm 300
100 800
240220
260280300320340
450400 500
165
1
23
Cabinet depth 450 mm cabinet width 800 mm
With cabinet depth 450 mm 1 vertically upwards up to the cabinet width line 800 mm
2 at the intersection point horizontal to the left read off value 3
Max cabinet weight 165 kg
Multi-purpose traverse Knauf Multi-Purpose Screw FN 43 x 65
Max screw load 125 kg
Required number of screws 165 kg 125 kg = 13 2 screws
are the min necessary
10
Knauf multi-purpose traversesThe multi-purpose traverse is suitable for accepting loads attached to the wall up to 15 kNm wall length eg cupboards boilers folding wall attached seats folding handles and similarThe multi-purpose traverse consists of a 23 mm thick multi-layer wooden board and galvanized sheet metal profiles It is fastened to the side of the floor-to-ceiling profilesThe attachment of the loads to the traverses should be performed using Knauf Multi-Purpose Screw FN
NoteTraverses for installation in damp and wet rooms see also system data sheet W38de Knauf Metal Stud Partitions AQUAPANELreg
Loads on partitions and furringsAnchoring in the traverses
Installation and applicationMulti-purpose traverse made of multi-layer wooden board and galvanized sheet metal profiles attached to the side of the CW studs UA profiles For CW studs screw fasten using the 6 enclosed Metal Screws LN 35 x 11 mm (3 per side) For UA profiles screw fasten with the 6 enclosed Drilling Screws ST 42 x 13 mm (3 per side)Arrangement in a rowUA profiles CW studs
Direction of installation Direction of installation
11
Loads on partitions and furringsAnchoring in the traverses
W234de-A10 View ndash Design with UA profile W234de-A13 View ndash Design with CW stud
W234de-H10 Horizontal section ndash Design with UA profile W234de-H13 Horizontal section ndash Design with CW studeg W626de eg W626de
W234de-V10 Vertical section ndash Design with UA profile W234de-V13 Vertical section ndash Design with CW studeg W116de eg W112de
Wooden board 555
Stud spacing 625 (grid dimension)
300
Multi-purpose traverse555 300 23 mm
Multi-layer wooden board
UA profile
Drillingscrew ST42 x 13(enclosed)
Wooden board 555
Stud spacing 625 (grid dimension)
300 Metal screw
LN 35 x 11(enclosed)
Multi-purpose traverse555 300 23 mm
Multi-layer wooden board
CW stud
Wooden board 555
Stud spacing 625 (grid dimension)
300
Multi-purpose traverse555 300 23 mm
UA profileDrilling screwST 42 x 13
Multi-purpose traverse555 300 23 mm
CW studMetal screwLN 35 x 11
48
eg folding wallattached seat
Knauf boardstrips
eg Supporthandle maxprojection 800 mm
Multi-purposetraverseUA profileKnauf boards
48
Multi-purposetraverseCW studKnauf boards
eg Cabinet
Scale 110 I Dimensions in mmDetails
Note No web cutouts in the CW studs are permissible for traverses to which the CW studs are attached
12
Knauf steel anchoring traverse with gypsum fibre insertThe steel anchoring traverse with gypsum fibre insert is suitable for accepting loads attached to the wall up to 15 kNm wall length eg cupboards shelves handrails and similarThe metal traverse with gypsum fibre insert consists of 075 mm thick sheet metal as well as an 18 mm thick gypsum fibre board It is fastened to the side of the floor-to-ceiling profiles The attachment of the loads to the traverses should be performed using Knauf Multi-Purpose Screw FNUse in partition systems where the requirement for non-combustible reaction to fire exists
Installation and applicationSteel anchoring traverse made of galvanized steel with gypsum fibre insert fastened to the CW studs UA profiles In case of CW studs crimp using a Stud Crimper and for UA profiles screw fasten with 6 Drilling screws LB 35 x 16 mmArrangement in a rowUA profiles CW studs
Loads on partitions and furringsAnchoring in the traverses
13
Scale 110 I Dimensions in mmDetailsW234de-A12 View - Design with UA profile W234de-A14 View - Design with CW stud
W234de-H12 Horizontal section - Design with UA profile W234de-H14 Horizontal section - Design with CW studeg W112de eg W112de
W234de-V12 Vertical section - Design with UA profile W234de-V14 Vertical section - Design with CW studeg W112de eg W112de
Traverse dimension 620
Stud spacing 625 (grid dimension)
290
Steel anchoring traversewith gypsum fibre insert
Traverse attached to UA profileusing drilling screws
UA profile
Steel anchoring traversewith gypsum fibre insert
CW stud
Crimp the traverse to the CW studusing a stud crimper
Traverse dimension 620
Stud spacing 625 (grid dimension)
290
Drilling screwLB 35 x 16
Steel anchoringtraverse with gypsum
fibre insert
UA profile Crimped Steel anchoring traversewith gypsum fibre insert
CW stud
eg Handrail
UA profileKnauf boards
Steel anchoring traversewith gypsum fibre insert
eg Handrail
CW studKnauf board
Steel anchoring traversewith gypsum fibre insert
Loads on partitions and furringsAnchoring in the traverses
Note No web cutouts in the CW studs are permissible for traverses to which the CW studs are attached
14
Loads on partitions and furringsAnchoring in the traverses
Knauf steel anchoring traverseThe steel anchoring traverse is suitable for accepting loads attached to the wall up to 10 kNm wall length eg towel holders cupboards shelves and similar Not suitable for dynamic loads such as folding wall attached seatsThe steel anchoring traverse consists of 075 mm thick sheet metal and are crimped onto the side using a stud crimper on the CW studs Particularly suitable for single-layer clad metal stud partitions and furrings where in case of cantilever loads gt 04 kNm (400 kgm) wall length the installation of a traverse is required
NoteTraverses for installation in damp and wet rooms see also system data sheet W38de Knauf Metal Stud Partitions AQUAPANELreg
Installation and applicationCrimp the steel anchoring traverse made of galvanized sheet steel to the CW studs using a Stud CrimperAdditional screw fastening of the steel anchoring traverse via screw fastening of the cladding (min 2 to 3 anchoring points) Reduce the screw spacing of the cladding if necessaryArrangement in a rowCW studs
Scale 110 I Dimensions in mmDetailsW234de-A11 View W234de V11 Vertical section
eg W111de
W234de-H11 Horizontal sectioneg W111de
Sheet metal gauge 075 mm
Steel anchoring traverse
CW stud
Crimp the traverse to the CW studusing the stud crimper
290
Traverse dimension 620
Stud spacing 625 (grid dimension)
eg Cabinet
CW stud
Knauf boardSteel anchoring traverse
Steel anchoring traverseCW stud
Crimped
Note No web cutouts in the CW studs are permissible for traverses to which the CW studs are attached
15
Full-length SanistandFloor-to-ceiling Sanistands made of galvanized UA profiles (min UA 75) 2 mm thick are suitable for transferring loads from traverses into the supporting structure or for fixing loads hanging onto walls such as school blackboards up to 15 kNm wall lengthFloor-to-ceiling Sanistands profiles are anchored to the basic floor and ceiling with door frame brackets or connection brackets for UA profiles The upper door frame bracket includes openings for routing cables such as pipe-in-pipe systems or electrical cablesThe loads are connected directly to the flange of the UA profile
W228de-A10 View
le 1000 mm
UW runnercontinuous
Door frameconnection brackettop connection withenclosed dowels
CW studAxial spacing suitedto partition system
UA profileas afloor-to-ceilingSanistand forbearing cantileverloads
UW runnercontinuous
Door frameconnection bracketbottom connectionwith enclosed dowels
Scale 110
Installation and applicationFloor-to-ceiling Sanistands made of UA profiles must be anchored to the basic floor and ceiling with door frame brackets or connection brackets for UA profiles The upper door frame bracket includes openings for routing cables such as pipe-in-pipe systems or electrical cables Fasten objects to UA profiles using threaded rods U washers and M1012 steel nuts or self-tapping screws
Loads on partitions and furringsFull-length Sanistand
Detail
Notes
Web cutouts are not permissible in UA Sanistand subject to cantilever loads point loads or linear distributed loadsMaximum screw load with connections to full height Sanistand (UA profile)Every UA profile flange and anchoring point may not exceed a resulting pull-out load of 150 kN (150 kg)Components similar to cantilevers such as foldable rails should be screwed onto two adjacent UA profilesUse suitable drilling screws eg Ejot Zebra Piasta Hilti S-MD or comparable
16
Loads on partitions and furringsFull-length Sanistand
Scale 110DetailsW116de-V1 Sanistand W116de-H1 SanistandVertical section I Without fire resistance Horizontal section I Without fire resistance
UW runnerUniflott + Trenn-Fix
UW runner
Additional UA profile
Sanistand withconcealed mount cistern
Knauf connectionbracket with enclosedM8 carriage bolts
Knauf conection bracket withenclosed M8 carriage bolt
2x 125 mm DiamantDiamant screw XTB
Additional CW stud
Knauf sealing tape
Board strip installationacc to W11de systemdata sheet
Stud spacing le 625 mm
CW stud profile
Additional CW studBoard strip installation in acc with W11de system data sheet
Knauf connection bracket withenclosed M8 carriage bolts
Additional UA profileSanitand with concealedmount cistern
Notes
Max partition height UA 50 = 300 m UA 75 = see system data sheet W11de Knauf Metal Stud Partition for the wall heights
Minimum cladding ge 18 mm Knauf Boards recommendation 2x 125 mm Knauf Diamant
Web cutouts are not permissible in UA Sanistand subject to cantilever loads point loads or linear distributed loadsObserve the manufacturersrsquo details for lateral UA profiles and cladding Additional UA profiles are required laterally on Sanistand mounts acc to DIN 18340 section 374 Only possible without additional UA profiles if the manufacturer of the Sanistand base or WC Sanistand permits itDeviating specifications of the Sanistand manufacturer must be considered and observed
17
Loads on partitions and furringsFull-length Sanistand
Notes
Max partition height rear W112de UA 50 = 300 m UA 75 = see system data sheet W11de Knauf Metal Stud Partition for the wall heights
Minimum cladding front wall installations ge 18 mm Knauf Boards recommendation 2x 125 mm Knauf Diamant
Web cutouts are not permissible in UA Sanistand subject to cantilever loads point loads or linear distributed loadsObserve the manufacturersrsquo details for lateral UA profiles and cladding Additional UA profiles are required laterally on Sanistand mounts acc to DIN 18340 section 374 Only possible without additional UA profiles if the manufacturer of the Sanistand base or WC Sanistand permits itDeviating specifications of the Sanistand manufacturer must be considered and observed
Scale 110DetailsW626Vde-V1 Without back anchoring W626Vde-H1 Without back anchoring Vertical section Horizontal section
UW runnerUniflott + Trenn-Fix
UW runner
Additional UA profile
Sanistand withconcealed mount cistern
Knauf connection bracket withenclosed M8 carriage bolt
Knauf connection bracket withenclosed M8 carriage bolt
2x 125 mm DiamantDiamant screw XTB
Knauf sealing tape
Sanistand withconcealed mount cisternKnauf connection bracket with
enclosed M8 carriage bolts
Stud spacing le 625 mm
UW runner
Knauf boardsCW stud
Additional UA profile
18
Loads on partitions and furringsFull-length Sanistand
Scale 110DetailsW626Vde-V2 Back anchoring in traverse W626Vde-H2 Back anchoring in traverse Vertical section Horizontal section
Sanistand withconcealed mount cistern
SealantUD profile made of insulation strips
UW runner
UW runner
UA profile
Knauf multi-purpose screw FN
Uniflott + Trenn-Fix
Multi-purpose traverse 555 300 23 mm
Knauf connection bracket withenclosed M8 carriage bolts
2x 125 mm DiamantDiamant screw XTB
Knauf connection bracket withenclosed M8 carriage bolt
Wall anchor installation acc to WCSanistand manufacturer specifications
Knauf sealing tape
Stud spacing le 625 mm
Multi-purpose traverse555 300 23 mm
UA profile
UA profile
Knauf connection bracket withenclosed M8 carriage bolt
Knauf connectionbracket with enclosedM8 carriage bolt
Wall anchorinstallation acc to
WC Sanistandmanufacturerspecifications
Notes
Max partition height rear W112de UA 50 = 300 m UA 75 = see system data sheet W11de Knauf Metal Stud Partitions for the wall heights
Minimum cladding front wall installations ge 18 mm Knauf Boards recommendation 2x 125 mm Knauf Diamant
Web cutouts are not permissible in UA Sanistand subject to cantilever loads point loads or linear distributed loadsObserve the manufacturersrsquo details for lateral UA profiles and cladding Additional UA profiles are required laterally on Sanistand mounts acc to DIN 18340 section 374 Only possible without additional UA profiles if the manufacturer of the Sanistand base or WC Sanistand permits itDeviating specifications of the Sanistand manufacturer must be considered and observed
19
Loads on partitions and furringsFull-length Sanistand
Scale 110DetailsW626Vde-V3 Back anchoring in UA profile W626Vde-H3 Back anchoring in UA profile Vertical section Horizontal section
Sanistand withconcealed mount cistern
SealantUD profile on insulation strips
UW runner
UW runner
Additional UA profile
Knauf multi-purpose screw FN
Uniflott + Trenn-Fix
UA profile
Knauf connection bracket withenclosed M8 carriage bolts
2x 125 mm DiamantDiamant screw XTB
Knauf connection bracket withenclosed M8 carriage bolts
Fixing bolts with nuts andwashers
Knauf sealing tape
Stud spacing le 625 mm
Additional UA profile
UA profile Fixing bolts with nutsand washers
Knauf connection bracket withenclosed M8 carriage bolts
Knauf connectionbracket with enclosedM8 carriage bolts
Notes
Max partition height at rear W112de UA 50 = 300 m UA 75 = see system data sheet W11de Knauf Metal Stud Partition for the wall heights
Minimum cladding front wall installations ge 18 mm Knauf Boards recommendation 2x 125 mm Knauf Diamant
Web cutouts are not permissible in UA Sanistand subject to cantilever loads point loads or linear distributed loadsObserve the manufacturersrsquo details for lateral UA profiles and cladding Additional UA profiles are required laterally on Sanistand mounts acc to DIN 18340 section 374 Only possible without additional UA profiles if the manufacturer of the Sanistand base or WC Sanistand permits itDeviating specifications of the Sanistand manufacturer must be considered and observed
20
Loads on partitions and furringsFull-length Sanistand
Scale 110DetailsW626Vde-V4 Back anchoring in mounting rail W626Vde-H4 Back anchoring in mounting rail Vertical section Horizontal section
Sanistand withconcealed mount cistern
2x 125 mm Diamant
SealantUD profile on insulation strips
UW runner
Diamant screw XTB
UA profile
Knauf multi-purpose screw FN
Mounting rail with fixing screw
Knauf connection bracket withenclosed M8 carriage bolt
Uniflott + Trenn-Fix
UA profile
Knauf connection bracket withenclosed M8 carriage bolt
Knauf sealing tapeUW runner
Stud spacing le 625 mm
UA profile
UA profile
Mounting railFixing screw
Mounting screw
Sanistand withconcealed mount cistern
Knauf connection bracket withenclosed M8 carriage bolt
Knauf connectionbracket with enclosedM8 carriage bolt
Notes
Max partition height rear W112de UA 50 = 300 m UA 75 = see system data sheet W11de Knauf Metal Stud Partitions for the wall heights
Minimum cladding front wall installations ge 18 mm Knauf Boards recommendation 2x 125 mm Knauf Diamant
Web cutouts are not permissible in UA Sanistand subject to cantilever loads point loads or linear distributed loadsObserve the manufacturersrsquo details for lateral UA profiles and cladding Additional UA profiles are required laterally on Sanistand mounts acc to DIN 18340 section 374 Only possible without additional UA profiles if the manufacturer of the Sanistand base or WC Sanistand permits itDeviating specifications of the Sanistand manufacturer must be considered and observed
21
Notes
In case of load attachment to ldquomulti-level ceiling systemsrdquo refer to the respective valid Knauf system data sheetsIn case of attachment of loads to free-spanning ceilings see system data sheet D13de Knauf Free-Spanning Ceilings
Attachment of loads to Knauf board ceilingsAdditional loads eg lighting fixtures curtain rails and similar can be fixed to Knauf board ceilings using universal dowels cavity dowels spring toggle dowels or Knauf Hartmut Hohlraumduumlbel cavity dowelsAdditional loads must be considered when determining the load class
NoteHeavy loads must be attached directly on load-bearing building elements (basic ceiling) or on auxiliary constructions eg traverses
For each area under load of the Knauf board ceiling the weight of thefastened components may not exceed the following limits
Permissible weight per ceiling area in kgmsup2Without fire resistance With fire resistance1)
15 61)Incaseofapplicationasafireresistanceceilingwithexposedceiling(multi-levelceilingsystem)15kgmsup2totalweightispermissiblefortheexposedceiling(includinginsulationlayerandattachedloads)attachedtothefireresistanceceiling
Furthermore the following conditions applyFor each anchoring point the components fastened to the board ceiling may not exceed the following weights
Fastening method Permissible weight per anchoring point in kgWithout fire resistance With fire resistance
Fastening in the cladding 6 05
Fastening to the grid 10 10
Fastening in the claddingKnauf Hartmut Hohlraumduumlbel cavity dowelScrew M5
Fastening to the gridKnauf Universalschraube FN multi-purpose screw eg curtain rail
The minimum separation spacings between individual attached loads must be observed to avoid local overloading of the ceiling The minimum separation clearance between two attachment points consists of both load radii for the point loadsThe load radius of a point load can be taken from the following diagram in dependence on the permissible weight per unit area for additional loads
Point load in kg
7570656055504540353025201510
0 2 3 4 5 6 7 8 9 10
Radiu
s in c
m
1
50
Fastening in the claddingpossible (without fire resistance)
3 kgmsup2 permissible additional weight (on the exposed ceiling under a fire resistance ceiling refer to the respective valid Knauf system data sheets)6 kgmsup2 permissible additional weight (with fire resistance)15 kgmsup2 permissible additional weight (without fire resistance)
Example fastening scheme at 15 kgmsup2
05 kg
10 kg
3 kgr = 25 cm
r = 46 cm
6 kgr = 355 cm
1 kg
r = 15 cm
r = 105 cm
NoteThe anchored loads can be transferred using several anchoring elements
Loads on board ceilingsFastening in the cladding grid
22
Knauf multi-purpose traversesThe multi-purpose traverse in Knauf board ceilings is suitable for the application of point loads up to 075 kN eg chandeliers music speakers or similarThe multi-purpose traverse consists of a 23 mm thick multi-layer wooden board and galvanized sheet metal profiles It is fastened to the side of the CD furring channelThe attachment of the loads to the traverses should be performed using Knauf Multi-Purpose Screw FNInstallation is possible in a double layer profile grid and flush profile grid
Installation and applicationBend the Daisy chain clip before lateral screw fastening The Daisy chain clip is then Z shaped The unpunched metal side of the Daisy chain clip is pushed onto the lower side of the traverse and then screw fastened laterally through the factory-made hole on the long side of the traverse Screw fasten 4x Daisy chain clips each using one drywall screw TN 35 x 35 about 100 mm from the corner of the multi-layer board on the long edge of the multi-purpose traverse Arrange an additional CD channel (length ge 650 mm) for every long edge in accordance with the width of the multi-purpose traverse Alternately a ceiling furring channel can be used for application of the multi-purpose traverse The supporting profiles are suspended using ceiling suspenders of load class 40 kg The suspenders may not be situated in the direct vicinity of the longitudinal area of the traverse as this will hinder the installation of the traverse Introduce the multi-purpose traverse between the support profiles bend the Daisy chain clip around the CD channel and engage it In case of single-layer cladding do not screw fasten the surface cladding with the multi-purpose traverse
1 Apply the Daisy chain clip 2 Bend the Daisy chain clip 3 Screw fasten the Daisy chain clip
Loads on board ceilingsAnchoring in the traverses
100 mm
23
Loads on board ceilingsAnchoring in the traverses
Scale 110 I Dimensions in mmDetailsD112de SO18 Vertical section ndash Multi-purpose traverse D113de SO12 Vertical section ndash Multi-purpose traverseeg with two additional CD channels I Without fire resistance eg with one additional CD channel I Without fire resistance
D112de SO19 Vertical section ndash Multi-purpose traverse D113de SO13 Vertical section ndash Multi-purpose traverseeg with two additional CD channels I Without fire resistance eg with one additional CD channel I Without fire resistance
D112de SO20 Top view ndash Multi-purpose traverse D113de SO14 Top view ndash Multi-purpose traverseeg with two additional CD channels I Without fire resistance eg with one additional CD channel I Without fire resistance
Fasten Daisy chain clip with drywall screwTN 35 x 35 to multi-purpose traverse
Additional CD channel with two suspendersLoad bearing capacity class ge 040 kN
Multi-purposetraverse555 300 23 mm
300
Furring channel spacing 500
Fasten Daisy chain clip with drywall screwTN 35 x 35 to multi-purpose traverse
Additional suspended load bearing capacity class ge 040 kNMulti-purposetraverse555 300 23 mm
300
Furring channel spacing 500
Additional CD channel with two suspendersLoad bearing capacity class ge 040 kN
Multi-purposetraverse555 300 23 mm
Fasten Daisy chain clip with drywall screwTN 35 x 35 to multi-purpose traverse
Wood panel 555approx
100
Additional suspenderload bearing capacityclass ge 040 kN
Multi-purposetraverse555 300 23 mm
Fasten Daisy chain clip with drywall screwTN 35 x 35 to multi-purpose traverse
Wood panel 555approx
100
Daisy chain clip
Furring channel spacing 500
Traverse
CDchannel
Multi-layerwood panel
Furring channel spacing 500
Multi-purposetraverse
Daisy chain clip
Multi-layerwood panel
Additional grid 4 additional suspension points (eg Nonius suspension)
All technical changes reserved Only the current printed instructions are valid The stated information represents current state-of-the-art Knauf technology The entire state of approved engineering rules appropriate standards guidelines and rules of crafts-manship are not included herewith These and all application instructions have to be adhered to separately by the installer Our warranty is expressly limited to our products in flawless condition All application quantities and delivery amounts are based on empirical data that are not easily transferable to other deviating areasAll rights reserved All amendments reprints and photocopies including those of excerpts require our expressed permission
The stated constructional and structural design specifications and characteristics of building physics of Knauf systems can only be ensured with the exclusive use of Knauf system components or other products expressly recommended by Knauf
Knauf Gips KG Am Bahnhof 7 97346 Iphofen GermanyKnauf DirectTechnical Advisory Service
knauf-direktknaufde
wwwknaufde
VT03deeng09190TI
The iPad App Knauf Infothek now provides all the current information and documents from Knauf Gips KG at any time and in every location in a clear and comfortable wayKnauf Infothek
Videos for Knauf systems and products can be found under the following linkwwwyoutubecomknaufEPD
7
Loads on partitions and furringsAnchoring in the cladding
RatingThe specified permissible cantilever loads are in accordance with the DIN 18183 or DIN 4103-1 at an eccentricity (spacing of resulting load to the wall surface) of max 300 mm The permissible load is reduced accordingly with greater eccentricity The determination of the permissible cantilever loads with divergent eccentricity is undertaken using the tables or diagrams on page 4 and page 5
Rating examples Determination of the permissible cabinet weight as well as the required minimum number of dowels (always ge 2)Metal stud partition W111de CW 50 cladding 125 mm Diamant GKFI acc to tableField of application static load max cantilever load 04 kNm (40 kgm) wall length Cabinet
widthCabinet depthmm
mm 100 200 300 400 500 600
400 31 28 25 22 19 16
600 465 42 375 33 285 24
800 62 56 50 44 38 32
1000 775 70 625 55 475 40
1200 93 84 75 66 57 48
Cabinet depth 400 mm cabinet width 1000 mm Max cabinet weight 55 kg
Cladding thickness 125 mm plastic cavity dowel
Max dowel load 30 kg
Required number of dowels 55 kg 30 kg = 18 2 dowels
are the min necessary
Metal stud partition W111de CW 75 cladding 2x 125 mm Diamant GKFI acc to diagramField of application static load max cantilever load 07 kNm (70 kgm) wall length
400
mm12001000
600
100 200 400 500 600mm
10
70
60
40
20 30
kg
100
80 90
110120
800
300
50
1
23
450
65
Cabinet depth
Cabinet width
Max permissible cabinet weightCabinet depth 450 mm cabinet width 800 mm
With cabinet depth 450 mm 1 vertically upwards up to the cabinet width line 800 mm
2 at the intersection point horizontal to the left ndash read off value 3
Max cabinet weight 65 kg
Cladding thickness 2x 125 mm Knauf Cavity Dowel Hartmut
Max dowel load 60 kg
Required number of dowels 65 kg 60 kg = 108 2 dowels
are the min necessary
8
Fields of applicationTraverses are built-in elements in lightweight partitions that transfer the fastening loads directly into the grid or into the flanking solid constructions
Selection of the traverse and grid in dependence on the expected loadFastening Load max Load type Profile min Cladding thickness min Independent
furring possible
Knauf Boards DiamantkNm2 mm mm
Steel anchoring traversesee page 14
07 Static CW 50 125 125 No07 Static CW 50 18 15 Yes10 Static CW 75 125 125 No10 Static CW 50 18 15 Yes
Metal traverse with gypsum fibre insertsee page 12
07 Static CW 50 125 125 No07 Static CW 50 18 15 Yes10 Static CW 75 125 125 No10 Static CW 50 18 15 Yes15 Static CW 50 18 15 No15 Static UA 50 18 15 Yes15 Dynamic UA 75 18 15 Yes
Multi-purpose traversesee page 10
07 Static CW 50 125 125 No07 Static CW 50 18 15 Yes10 Static CW 75 125 125 No10 Static CW 50 18 15 Yes15 Static CW 50 18 15 No15 Static UA 50 18 15 Yes15 Dynamic UA 75 18 15 Yes
Fixing loadsFor fixing of cantilever loads
Dowel screw Maximum screw dowel load capacity in kgKnauf Cavity Dowel Hartmut
fischer MHD 5 x 65 S
Knauf Multi- Purpose Screw FN 43 x 65
fischer plastic cavity dowels 8 x 50 with Knauf Multi-Purpose Screw FN 43 x 65
Wood screw Oslash 50 mm
Wood screw Oslash 60 mm
TraversesSteel anchoring traverse 75 ndash 45 40 45 45
Metal traversewith gypsum fibre insert
90 75 65 46 55 70
Multi-purpose traverse ndash ndash 125 ndash 115 165
Measuredwith300mmeccentricity
Loads on partitions and furringsAnchoring in the traverses
NotesStatic loads in this respect are permanently fastened loads such as towel rails cabinets shelves and boilers Dynamic loads are exerted by fastened components which are subjected to continuous changes in load such as handrails fold-down seats and folding handles
9
Loads on partitions and furringsAnchoring in the traverses
RatingThe specified permissible cantilever loads are in accordance with the DIN 18183 or DIN 4103-1 at an eccentricity (spacing of resulting load to the wall surface) of max 300 mm The permissible load is reduced accordingly with greater eccentricity The determination of the permissible cantilever loads with divergent eccentricity is undertaken using the tables or diagrams on page 4 and page 5
Rating examples Determination of the permissible cabinet weight as well as the required minimum number of dowels (always ge 2)Metal stud partition W111de CW 50 cladding 18 mm Knauf board acc to tableField of application static load max cantilever load 07 kNm (70 kgm) wall length Cabinet
widthCabinet depthmm
mm 100 200 300 400 500 600400 43 40 37 34 31 28600 645 60 555 51 465 42800 86 80 74 68 62 561000 1075 100 925 85 775 701200 129 120 111 102 93 84
Cabinet depth 500 mm cabinet width 800 mm Max cabinet weight 62 kg Fixing traverse Knauf Multi-Purpose Screw FN 43 x 65
Max screw load 45 kg
Required number of screws 62 kg 45 kg = 14 2 screws
are the min necessary
Metal stud partition W111de UA 75 cladding 15 mm Diamant GKFI acc to diagram
Field of application dynamic load max cantilever load 15 kNm (150 kgm) wall length
20
400
Cabinet depth100 200 600
Max permissible cabinet weight
140120
80
4060
kg
200
160
180
Cabinet width
mm
1000
1200
600
mm 300
100 800
240220
260280300320340
450400 500
165
1
23
Cabinet depth 450 mm cabinet width 800 mm
With cabinet depth 450 mm 1 vertically upwards up to the cabinet width line 800 mm
2 at the intersection point horizontal to the left read off value 3
Max cabinet weight 165 kg
Multi-purpose traverse Knauf Multi-Purpose Screw FN 43 x 65
Max screw load 125 kg
Required number of screws 165 kg 125 kg = 13 2 screws
are the min necessary
10
Knauf multi-purpose traversesThe multi-purpose traverse is suitable for accepting loads attached to the wall up to 15 kNm wall length eg cupboards boilers folding wall attached seats folding handles and similarThe multi-purpose traverse consists of a 23 mm thick multi-layer wooden board and galvanized sheet metal profiles It is fastened to the side of the floor-to-ceiling profilesThe attachment of the loads to the traverses should be performed using Knauf Multi-Purpose Screw FN
NoteTraverses for installation in damp and wet rooms see also system data sheet W38de Knauf Metal Stud Partitions AQUAPANELreg
Loads on partitions and furringsAnchoring in the traverses
Installation and applicationMulti-purpose traverse made of multi-layer wooden board and galvanized sheet metal profiles attached to the side of the CW studs UA profiles For CW studs screw fasten using the 6 enclosed Metal Screws LN 35 x 11 mm (3 per side) For UA profiles screw fasten with the 6 enclosed Drilling Screws ST 42 x 13 mm (3 per side)Arrangement in a rowUA profiles CW studs
Direction of installation Direction of installation
11
Loads on partitions and furringsAnchoring in the traverses
W234de-A10 View ndash Design with UA profile W234de-A13 View ndash Design with CW stud
W234de-H10 Horizontal section ndash Design with UA profile W234de-H13 Horizontal section ndash Design with CW studeg W626de eg W626de
W234de-V10 Vertical section ndash Design with UA profile W234de-V13 Vertical section ndash Design with CW studeg W116de eg W112de
Wooden board 555
Stud spacing 625 (grid dimension)
300
Multi-purpose traverse555 300 23 mm
Multi-layer wooden board
UA profile
Drillingscrew ST42 x 13(enclosed)
Wooden board 555
Stud spacing 625 (grid dimension)
300 Metal screw
LN 35 x 11(enclosed)
Multi-purpose traverse555 300 23 mm
Multi-layer wooden board
CW stud
Wooden board 555
Stud spacing 625 (grid dimension)
300
Multi-purpose traverse555 300 23 mm
UA profileDrilling screwST 42 x 13
Multi-purpose traverse555 300 23 mm
CW studMetal screwLN 35 x 11
48
eg folding wallattached seat
Knauf boardstrips
eg Supporthandle maxprojection 800 mm
Multi-purposetraverseUA profileKnauf boards
48
Multi-purposetraverseCW studKnauf boards
eg Cabinet
Scale 110 I Dimensions in mmDetails
Note No web cutouts in the CW studs are permissible for traverses to which the CW studs are attached
12
Knauf steel anchoring traverse with gypsum fibre insertThe steel anchoring traverse with gypsum fibre insert is suitable for accepting loads attached to the wall up to 15 kNm wall length eg cupboards shelves handrails and similarThe metal traverse with gypsum fibre insert consists of 075 mm thick sheet metal as well as an 18 mm thick gypsum fibre board It is fastened to the side of the floor-to-ceiling profiles The attachment of the loads to the traverses should be performed using Knauf Multi-Purpose Screw FNUse in partition systems where the requirement for non-combustible reaction to fire exists
Installation and applicationSteel anchoring traverse made of galvanized steel with gypsum fibre insert fastened to the CW studs UA profiles In case of CW studs crimp using a Stud Crimper and for UA profiles screw fasten with 6 Drilling screws LB 35 x 16 mmArrangement in a rowUA profiles CW studs
Loads on partitions and furringsAnchoring in the traverses
13
Scale 110 I Dimensions in mmDetailsW234de-A12 View - Design with UA profile W234de-A14 View - Design with CW stud
W234de-H12 Horizontal section - Design with UA profile W234de-H14 Horizontal section - Design with CW studeg W112de eg W112de
W234de-V12 Vertical section - Design with UA profile W234de-V14 Vertical section - Design with CW studeg W112de eg W112de
Traverse dimension 620
Stud spacing 625 (grid dimension)
290
Steel anchoring traversewith gypsum fibre insert
Traverse attached to UA profileusing drilling screws
UA profile
Steel anchoring traversewith gypsum fibre insert
CW stud
Crimp the traverse to the CW studusing a stud crimper
Traverse dimension 620
Stud spacing 625 (grid dimension)
290
Drilling screwLB 35 x 16
Steel anchoringtraverse with gypsum
fibre insert
UA profile Crimped Steel anchoring traversewith gypsum fibre insert
CW stud
eg Handrail
UA profileKnauf boards
Steel anchoring traversewith gypsum fibre insert
eg Handrail
CW studKnauf board
Steel anchoring traversewith gypsum fibre insert
Loads on partitions and furringsAnchoring in the traverses
Note No web cutouts in the CW studs are permissible for traverses to which the CW studs are attached
14
Loads on partitions and furringsAnchoring in the traverses
Knauf steel anchoring traverseThe steel anchoring traverse is suitable for accepting loads attached to the wall up to 10 kNm wall length eg towel holders cupboards shelves and similar Not suitable for dynamic loads such as folding wall attached seatsThe steel anchoring traverse consists of 075 mm thick sheet metal and are crimped onto the side using a stud crimper on the CW studs Particularly suitable for single-layer clad metal stud partitions and furrings where in case of cantilever loads gt 04 kNm (400 kgm) wall length the installation of a traverse is required
NoteTraverses for installation in damp and wet rooms see also system data sheet W38de Knauf Metal Stud Partitions AQUAPANELreg
Installation and applicationCrimp the steel anchoring traverse made of galvanized sheet steel to the CW studs using a Stud CrimperAdditional screw fastening of the steel anchoring traverse via screw fastening of the cladding (min 2 to 3 anchoring points) Reduce the screw spacing of the cladding if necessaryArrangement in a rowCW studs
Scale 110 I Dimensions in mmDetailsW234de-A11 View W234de V11 Vertical section
eg W111de
W234de-H11 Horizontal sectioneg W111de
Sheet metal gauge 075 mm
Steel anchoring traverse
CW stud
Crimp the traverse to the CW studusing the stud crimper
290
Traverse dimension 620
Stud spacing 625 (grid dimension)
eg Cabinet
CW stud
Knauf boardSteel anchoring traverse
Steel anchoring traverseCW stud
Crimped
Note No web cutouts in the CW studs are permissible for traverses to which the CW studs are attached
15
Full-length SanistandFloor-to-ceiling Sanistands made of galvanized UA profiles (min UA 75) 2 mm thick are suitable for transferring loads from traverses into the supporting structure or for fixing loads hanging onto walls such as school blackboards up to 15 kNm wall lengthFloor-to-ceiling Sanistands profiles are anchored to the basic floor and ceiling with door frame brackets or connection brackets for UA profiles The upper door frame bracket includes openings for routing cables such as pipe-in-pipe systems or electrical cablesThe loads are connected directly to the flange of the UA profile
W228de-A10 View
le 1000 mm
UW runnercontinuous
Door frameconnection brackettop connection withenclosed dowels
CW studAxial spacing suitedto partition system
UA profileas afloor-to-ceilingSanistand forbearing cantileverloads
UW runnercontinuous
Door frameconnection bracketbottom connectionwith enclosed dowels
Scale 110
Installation and applicationFloor-to-ceiling Sanistands made of UA profiles must be anchored to the basic floor and ceiling with door frame brackets or connection brackets for UA profiles The upper door frame bracket includes openings for routing cables such as pipe-in-pipe systems or electrical cables Fasten objects to UA profiles using threaded rods U washers and M1012 steel nuts or self-tapping screws
Loads on partitions and furringsFull-length Sanistand
Detail
Notes
Web cutouts are not permissible in UA Sanistand subject to cantilever loads point loads or linear distributed loadsMaximum screw load with connections to full height Sanistand (UA profile)Every UA profile flange and anchoring point may not exceed a resulting pull-out load of 150 kN (150 kg)Components similar to cantilevers such as foldable rails should be screwed onto two adjacent UA profilesUse suitable drilling screws eg Ejot Zebra Piasta Hilti S-MD or comparable
16
Loads on partitions and furringsFull-length Sanistand
Scale 110DetailsW116de-V1 Sanistand W116de-H1 SanistandVertical section I Without fire resistance Horizontal section I Without fire resistance
UW runnerUniflott + Trenn-Fix
UW runner
Additional UA profile
Sanistand withconcealed mount cistern
Knauf connectionbracket with enclosedM8 carriage bolts
Knauf conection bracket withenclosed M8 carriage bolt
2x 125 mm DiamantDiamant screw XTB
Additional CW stud
Knauf sealing tape
Board strip installationacc to W11de systemdata sheet
Stud spacing le 625 mm
CW stud profile
Additional CW studBoard strip installation in acc with W11de system data sheet
Knauf connection bracket withenclosed M8 carriage bolts
Additional UA profileSanitand with concealedmount cistern
Notes
Max partition height UA 50 = 300 m UA 75 = see system data sheet W11de Knauf Metal Stud Partition for the wall heights
Minimum cladding ge 18 mm Knauf Boards recommendation 2x 125 mm Knauf Diamant
Web cutouts are not permissible in UA Sanistand subject to cantilever loads point loads or linear distributed loadsObserve the manufacturersrsquo details for lateral UA profiles and cladding Additional UA profiles are required laterally on Sanistand mounts acc to DIN 18340 section 374 Only possible without additional UA profiles if the manufacturer of the Sanistand base or WC Sanistand permits itDeviating specifications of the Sanistand manufacturer must be considered and observed
17
Loads on partitions and furringsFull-length Sanistand
Notes
Max partition height rear W112de UA 50 = 300 m UA 75 = see system data sheet W11de Knauf Metal Stud Partition for the wall heights
Minimum cladding front wall installations ge 18 mm Knauf Boards recommendation 2x 125 mm Knauf Diamant
Web cutouts are not permissible in UA Sanistand subject to cantilever loads point loads or linear distributed loadsObserve the manufacturersrsquo details for lateral UA profiles and cladding Additional UA profiles are required laterally on Sanistand mounts acc to DIN 18340 section 374 Only possible without additional UA profiles if the manufacturer of the Sanistand base or WC Sanistand permits itDeviating specifications of the Sanistand manufacturer must be considered and observed
Scale 110DetailsW626Vde-V1 Without back anchoring W626Vde-H1 Without back anchoring Vertical section Horizontal section
UW runnerUniflott + Trenn-Fix
UW runner
Additional UA profile
Sanistand withconcealed mount cistern
Knauf connection bracket withenclosed M8 carriage bolt
Knauf connection bracket withenclosed M8 carriage bolt
2x 125 mm DiamantDiamant screw XTB
Knauf sealing tape
Sanistand withconcealed mount cisternKnauf connection bracket with
enclosed M8 carriage bolts
Stud spacing le 625 mm
UW runner
Knauf boardsCW stud
Additional UA profile
18
Loads on partitions and furringsFull-length Sanistand
Scale 110DetailsW626Vde-V2 Back anchoring in traverse W626Vde-H2 Back anchoring in traverse Vertical section Horizontal section
Sanistand withconcealed mount cistern
SealantUD profile made of insulation strips
UW runner
UW runner
UA profile
Knauf multi-purpose screw FN
Uniflott + Trenn-Fix
Multi-purpose traverse 555 300 23 mm
Knauf connection bracket withenclosed M8 carriage bolts
2x 125 mm DiamantDiamant screw XTB
Knauf connection bracket withenclosed M8 carriage bolt
Wall anchor installation acc to WCSanistand manufacturer specifications
Knauf sealing tape
Stud spacing le 625 mm
Multi-purpose traverse555 300 23 mm
UA profile
UA profile
Knauf connection bracket withenclosed M8 carriage bolt
Knauf connectionbracket with enclosedM8 carriage bolt
Wall anchorinstallation acc to
WC Sanistandmanufacturerspecifications
Notes
Max partition height rear W112de UA 50 = 300 m UA 75 = see system data sheet W11de Knauf Metal Stud Partitions for the wall heights
Minimum cladding front wall installations ge 18 mm Knauf Boards recommendation 2x 125 mm Knauf Diamant
Web cutouts are not permissible in UA Sanistand subject to cantilever loads point loads or linear distributed loadsObserve the manufacturersrsquo details for lateral UA profiles and cladding Additional UA profiles are required laterally on Sanistand mounts acc to DIN 18340 section 374 Only possible without additional UA profiles if the manufacturer of the Sanistand base or WC Sanistand permits itDeviating specifications of the Sanistand manufacturer must be considered and observed
19
Loads on partitions and furringsFull-length Sanistand
Scale 110DetailsW626Vde-V3 Back anchoring in UA profile W626Vde-H3 Back anchoring in UA profile Vertical section Horizontal section
Sanistand withconcealed mount cistern
SealantUD profile on insulation strips
UW runner
UW runner
Additional UA profile
Knauf multi-purpose screw FN
Uniflott + Trenn-Fix
UA profile
Knauf connection bracket withenclosed M8 carriage bolts
2x 125 mm DiamantDiamant screw XTB
Knauf connection bracket withenclosed M8 carriage bolts
Fixing bolts with nuts andwashers
Knauf sealing tape
Stud spacing le 625 mm
Additional UA profile
UA profile Fixing bolts with nutsand washers
Knauf connection bracket withenclosed M8 carriage bolts
Knauf connectionbracket with enclosedM8 carriage bolts
Notes
Max partition height at rear W112de UA 50 = 300 m UA 75 = see system data sheet W11de Knauf Metal Stud Partition for the wall heights
Minimum cladding front wall installations ge 18 mm Knauf Boards recommendation 2x 125 mm Knauf Diamant
Web cutouts are not permissible in UA Sanistand subject to cantilever loads point loads or linear distributed loadsObserve the manufacturersrsquo details for lateral UA profiles and cladding Additional UA profiles are required laterally on Sanistand mounts acc to DIN 18340 section 374 Only possible without additional UA profiles if the manufacturer of the Sanistand base or WC Sanistand permits itDeviating specifications of the Sanistand manufacturer must be considered and observed
20
Loads on partitions and furringsFull-length Sanistand
Scale 110DetailsW626Vde-V4 Back anchoring in mounting rail W626Vde-H4 Back anchoring in mounting rail Vertical section Horizontal section
Sanistand withconcealed mount cistern
2x 125 mm Diamant
SealantUD profile on insulation strips
UW runner
Diamant screw XTB
UA profile
Knauf multi-purpose screw FN
Mounting rail with fixing screw
Knauf connection bracket withenclosed M8 carriage bolt
Uniflott + Trenn-Fix
UA profile
Knauf connection bracket withenclosed M8 carriage bolt
Knauf sealing tapeUW runner
Stud spacing le 625 mm
UA profile
UA profile
Mounting railFixing screw
Mounting screw
Sanistand withconcealed mount cistern
Knauf connection bracket withenclosed M8 carriage bolt
Knauf connectionbracket with enclosedM8 carriage bolt
Notes
Max partition height rear W112de UA 50 = 300 m UA 75 = see system data sheet W11de Knauf Metal Stud Partitions for the wall heights
Minimum cladding front wall installations ge 18 mm Knauf Boards recommendation 2x 125 mm Knauf Diamant
Web cutouts are not permissible in UA Sanistand subject to cantilever loads point loads or linear distributed loadsObserve the manufacturersrsquo details for lateral UA profiles and cladding Additional UA profiles are required laterally on Sanistand mounts acc to DIN 18340 section 374 Only possible without additional UA profiles if the manufacturer of the Sanistand base or WC Sanistand permits itDeviating specifications of the Sanistand manufacturer must be considered and observed
21
Notes
In case of load attachment to ldquomulti-level ceiling systemsrdquo refer to the respective valid Knauf system data sheetsIn case of attachment of loads to free-spanning ceilings see system data sheet D13de Knauf Free-Spanning Ceilings
Attachment of loads to Knauf board ceilingsAdditional loads eg lighting fixtures curtain rails and similar can be fixed to Knauf board ceilings using universal dowels cavity dowels spring toggle dowels or Knauf Hartmut Hohlraumduumlbel cavity dowelsAdditional loads must be considered when determining the load class
NoteHeavy loads must be attached directly on load-bearing building elements (basic ceiling) or on auxiliary constructions eg traverses
For each area under load of the Knauf board ceiling the weight of thefastened components may not exceed the following limits
Permissible weight per ceiling area in kgmsup2Without fire resistance With fire resistance1)
15 61)Incaseofapplicationasafireresistanceceilingwithexposedceiling(multi-levelceilingsystem)15kgmsup2totalweightispermissiblefortheexposedceiling(includinginsulationlayerandattachedloads)attachedtothefireresistanceceiling
Furthermore the following conditions applyFor each anchoring point the components fastened to the board ceiling may not exceed the following weights
Fastening method Permissible weight per anchoring point in kgWithout fire resistance With fire resistance
Fastening in the cladding 6 05
Fastening to the grid 10 10
Fastening in the claddingKnauf Hartmut Hohlraumduumlbel cavity dowelScrew M5
Fastening to the gridKnauf Universalschraube FN multi-purpose screw eg curtain rail
The minimum separation spacings between individual attached loads must be observed to avoid local overloading of the ceiling The minimum separation clearance between two attachment points consists of both load radii for the point loadsThe load radius of a point load can be taken from the following diagram in dependence on the permissible weight per unit area for additional loads
Point load in kg
7570656055504540353025201510
0 2 3 4 5 6 7 8 9 10
Radiu
s in c
m
1
50
Fastening in the claddingpossible (without fire resistance)
3 kgmsup2 permissible additional weight (on the exposed ceiling under a fire resistance ceiling refer to the respective valid Knauf system data sheets)6 kgmsup2 permissible additional weight (with fire resistance)15 kgmsup2 permissible additional weight (without fire resistance)
Example fastening scheme at 15 kgmsup2
05 kg
10 kg
3 kgr = 25 cm
r = 46 cm
6 kgr = 355 cm
1 kg
r = 15 cm
r = 105 cm
NoteThe anchored loads can be transferred using several anchoring elements
Loads on board ceilingsFastening in the cladding grid
22
Knauf multi-purpose traversesThe multi-purpose traverse in Knauf board ceilings is suitable for the application of point loads up to 075 kN eg chandeliers music speakers or similarThe multi-purpose traverse consists of a 23 mm thick multi-layer wooden board and galvanized sheet metal profiles It is fastened to the side of the CD furring channelThe attachment of the loads to the traverses should be performed using Knauf Multi-Purpose Screw FNInstallation is possible in a double layer profile grid and flush profile grid
Installation and applicationBend the Daisy chain clip before lateral screw fastening The Daisy chain clip is then Z shaped The unpunched metal side of the Daisy chain clip is pushed onto the lower side of the traverse and then screw fastened laterally through the factory-made hole on the long side of the traverse Screw fasten 4x Daisy chain clips each using one drywall screw TN 35 x 35 about 100 mm from the corner of the multi-layer board on the long edge of the multi-purpose traverse Arrange an additional CD channel (length ge 650 mm) for every long edge in accordance with the width of the multi-purpose traverse Alternately a ceiling furring channel can be used for application of the multi-purpose traverse The supporting profiles are suspended using ceiling suspenders of load class 40 kg The suspenders may not be situated in the direct vicinity of the longitudinal area of the traverse as this will hinder the installation of the traverse Introduce the multi-purpose traverse between the support profiles bend the Daisy chain clip around the CD channel and engage it In case of single-layer cladding do not screw fasten the surface cladding with the multi-purpose traverse
1 Apply the Daisy chain clip 2 Bend the Daisy chain clip 3 Screw fasten the Daisy chain clip
Loads on board ceilingsAnchoring in the traverses
100 mm
23
Loads on board ceilingsAnchoring in the traverses
Scale 110 I Dimensions in mmDetailsD112de SO18 Vertical section ndash Multi-purpose traverse D113de SO12 Vertical section ndash Multi-purpose traverseeg with two additional CD channels I Without fire resistance eg with one additional CD channel I Without fire resistance
D112de SO19 Vertical section ndash Multi-purpose traverse D113de SO13 Vertical section ndash Multi-purpose traverseeg with two additional CD channels I Without fire resistance eg with one additional CD channel I Without fire resistance
D112de SO20 Top view ndash Multi-purpose traverse D113de SO14 Top view ndash Multi-purpose traverseeg with two additional CD channels I Without fire resistance eg with one additional CD channel I Without fire resistance
Fasten Daisy chain clip with drywall screwTN 35 x 35 to multi-purpose traverse
Additional CD channel with two suspendersLoad bearing capacity class ge 040 kN
Multi-purposetraverse555 300 23 mm
300
Furring channel spacing 500
Fasten Daisy chain clip with drywall screwTN 35 x 35 to multi-purpose traverse
Additional suspended load bearing capacity class ge 040 kNMulti-purposetraverse555 300 23 mm
300
Furring channel spacing 500
Additional CD channel with two suspendersLoad bearing capacity class ge 040 kN
Multi-purposetraverse555 300 23 mm
Fasten Daisy chain clip with drywall screwTN 35 x 35 to multi-purpose traverse
Wood panel 555approx
100
Additional suspenderload bearing capacityclass ge 040 kN
Multi-purposetraverse555 300 23 mm
Fasten Daisy chain clip with drywall screwTN 35 x 35 to multi-purpose traverse
Wood panel 555approx
100
Daisy chain clip
Furring channel spacing 500
Traverse
CDchannel
Multi-layerwood panel
Furring channel spacing 500
Multi-purposetraverse
Daisy chain clip
Multi-layerwood panel
Additional grid 4 additional suspension points (eg Nonius suspension)
All technical changes reserved Only the current printed instructions are valid The stated information represents current state-of-the-art Knauf technology The entire state of approved engineering rules appropriate standards guidelines and rules of crafts-manship are not included herewith These and all application instructions have to be adhered to separately by the installer Our warranty is expressly limited to our products in flawless condition All application quantities and delivery amounts are based on empirical data that are not easily transferable to other deviating areasAll rights reserved All amendments reprints and photocopies including those of excerpts require our expressed permission
The stated constructional and structural design specifications and characteristics of building physics of Knauf systems can only be ensured with the exclusive use of Knauf system components or other products expressly recommended by Knauf
Knauf Gips KG Am Bahnhof 7 97346 Iphofen GermanyKnauf DirectTechnical Advisory Service
knauf-direktknaufde
wwwknaufde
VT03deeng09190TI
The iPad App Knauf Infothek now provides all the current information and documents from Knauf Gips KG at any time and in every location in a clear and comfortable wayKnauf Infothek
Videos for Knauf systems and products can be found under the following linkwwwyoutubecomknaufEPD
8
Fields of applicationTraverses are built-in elements in lightweight partitions that transfer the fastening loads directly into the grid or into the flanking solid constructions
Selection of the traverse and grid in dependence on the expected loadFastening Load max Load type Profile min Cladding thickness min Independent
furring possible
Knauf Boards DiamantkNm2 mm mm
Steel anchoring traversesee page 14
07 Static CW 50 125 125 No07 Static CW 50 18 15 Yes10 Static CW 75 125 125 No10 Static CW 50 18 15 Yes
Metal traverse with gypsum fibre insertsee page 12
07 Static CW 50 125 125 No07 Static CW 50 18 15 Yes10 Static CW 75 125 125 No10 Static CW 50 18 15 Yes15 Static CW 50 18 15 No15 Static UA 50 18 15 Yes15 Dynamic UA 75 18 15 Yes
Multi-purpose traversesee page 10
07 Static CW 50 125 125 No07 Static CW 50 18 15 Yes10 Static CW 75 125 125 No10 Static CW 50 18 15 Yes15 Static CW 50 18 15 No15 Static UA 50 18 15 Yes15 Dynamic UA 75 18 15 Yes
Fixing loadsFor fixing of cantilever loads
Dowel screw Maximum screw dowel load capacity in kgKnauf Cavity Dowel Hartmut
fischer MHD 5 x 65 S
Knauf Multi- Purpose Screw FN 43 x 65
fischer plastic cavity dowels 8 x 50 with Knauf Multi-Purpose Screw FN 43 x 65
Wood screw Oslash 50 mm
Wood screw Oslash 60 mm
TraversesSteel anchoring traverse 75 ndash 45 40 45 45
Metal traversewith gypsum fibre insert
90 75 65 46 55 70
Multi-purpose traverse ndash ndash 125 ndash 115 165
Measuredwith300mmeccentricity
Loads on partitions and furringsAnchoring in the traverses
NotesStatic loads in this respect are permanently fastened loads such as towel rails cabinets shelves and boilers Dynamic loads are exerted by fastened components which are subjected to continuous changes in load such as handrails fold-down seats and folding handles
9
Loads on partitions and furringsAnchoring in the traverses
RatingThe specified permissible cantilever loads are in accordance with the DIN 18183 or DIN 4103-1 at an eccentricity (spacing of resulting load to the wall surface) of max 300 mm The permissible load is reduced accordingly with greater eccentricity The determination of the permissible cantilever loads with divergent eccentricity is undertaken using the tables or diagrams on page 4 and page 5
Rating examples Determination of the permissible cabinet weight as well as the required minimum number of dowels (always ge 2)Metal stud partition W111de CW 50 cladding 18 mm Knauf board acc to tableField of application static load max cantilever load 07 kNm (70 kgm) wall length Cabinet
widthCabinet depthmm
mm 100 200 300 400 500 600400 43 40 37 34 31 28600 645 60 555 51 465 42800 86 80 74 68 62 561000 1075 100 925 85 775 701200 129 120 111 102 93 84
Cabinet depth 500 mm cabinet width 800 mm Max cabinet weight 62 kg Fixing traverse Knauf Multi-Purpose Screw FN 43 x 65
Max screw load 45 kg
Required number of screws 62 kg 45 kg = 14 2 screws
are the min necessary
Metal stud partition W111de UA 75 cladding 15 mm Diamant GKFI acc to diagram
Field of application dynamic load max cantilever load 15 kNm (150 kgm) wall length
20
400
Cabinet depth100 200 600
Max permissible cabinet weight
140120
80
4060
kg
200
160
180
Cabinet width
mm
1000
1200
600
mm 300
100 800
240220
260280300320340
450400 500
165
1
23
Cabinet depth 450 mm cabinet width 800 mm
With cabinet depth 450 mm 1 vertically upwards up to the cabinet width line 800 mm
2 at the intersection point horizontal to the left read off value 3
Max cabinet weight 165 kg
Multi-purpose traverse Knauf Multi-Purpose Screw FN 43 x 65
Max screw load 125 kg
Required number of screws 165 kg 125 kg = 13 2 screws
are the min necessary
10
Knauf multi-purpose traversesThe multi-purpose traverse is suitable for accepting loads attached to the wall up to 15 kNm wall length eg cupboards boilers folding wall attached seats folding handles and similarThe multi-purpose traverse consists of a 23 mm thick multi-layer wooden board and galvanized sheet metal profiles It is fastened to the side of the floor-to-ceiling profilesThe attachment of the loads to the traverses should be performed using Knauf Multi-Purpose Screw FN
NoteTraverses for installation in damp and wet rooms see also system data sheet W38de Knauf Metal Stud Partitions AQUAPANELreg
Loads on partitions and furringsAnchoring in the traverses
Installation and applicationMulti-purpose traverse made of multi-layer wooden board and galvanized sheet metal profiles attached to the side of the CW studs UA profiles For CW studs screw fasten using the 6 enclosed Metal Screws LN 35 x 11 mm (3 per side) For UA profiles screw fasten with the 6 enclosed Drilling Screws ST 42 x 13 mm (3 per side)Arrangement in a rowUA profiles CW studs
Direction of installation Direction of installation
11
Loads on partitions and furringsAnchoring in the traverses
W234de-A10 View ndash Design with UA profile W234de-A13 View ndash Design with CW stud
W234de-H10 Horizontal section ndash Design with UA profile W234de-H13 Horizontal section ndash Design with CW studeg W626de eg W626de
W234de-V10 Vertical section ndash Design with UA profile W234de-V13 Vertical section ndash Design with CW studeg W116de eg W112de
Wooden board 555
Stud spacing 625 (grid dimension)
300
Multi-purpose traverse555 300 23 mm
Multi-layer wooden board
UA profile
Drillingscrew ST42 x 13(enclosed)
Wooden board 555
Stud spacing 625 (grid dimension)
300 Metal screw
LN 35 x 11(enclosed)
Multi-purpose traverse555 300 23 mm
Multi-layer wooden board
CW stud
Wooden board 555
Stud spacing 625 (grid dimension)
300
Multi-purpose traverse555 300 23 mm
UA profileDrilling screwST 42 x 13
Multi-purpose traverse555 300 23 mm
CW studMetal screwLN 35 x 11
48
eg folding wallattached seat
Knauf boardstrips
eg Supporthandle maxprojection 800 mm
Multi-purposetraverseUA profileKnauf boards
48
Multi-purposetraverseCW studKnauf boards
eg Cabinet
Scale 110 I Dimensions in mmDetails
Note No web cutouts in the CW studs are permissible for traverses to which the CW studs are attached
12
Knauf steel anchoring traverse with gypsum fibre insertThe steel anchoring traverse with gypsum fibre insert is suitable for accepting loads attached to the wall up to 15 kNm wall length eg cupboards shelves handrails and similarThe metal traverse with gypsum fibre insert consists of 075 mm thick sheet metal as well as an 18 mm thick gypsum fibre board It is fastened to the side of the floor-to-ceiling profiles The attachment of the loads to the traverses should be performed using Knauf Multi-Purpose Screw FNUse in partition systems where the requirement for non-combustible reaction to fire exists
Installation and applicationSteel anchoring traverse made of galvanized steel with gypsum fibre insert fastened to the CW studs UA profiles In case of CW studs crimp using a Stud Crimper and for UA profiles screw fasten with 6 Drilling screws LB 35 x 16 mmArrangement in a rowUA profiles CW studs
Loads on partitions and furringsAnchoring in the traverses
13
Scale 110 I Dimensions in mmDetailsW234de-A12 View - Design with UA profile W234de-A14 View - Design with CW stud
W234de-H12 Horizontal section - Design with UA profile W234de-H14 Horizontal section - Design with CW studeg W112de eg W112de
W234de-V12 Vertical section - Design with UA profile W234de-V14 Vertical section - Design with CW studeg W112de eg W112de
Traverse dimension 620
Stud spacing 625 (grid dimension)
290
Steel anchoring traversewith gypsum fibre insert
Traverse attached to UA profileusing drilling screws
UA profile
Steel anchoring traversewith gypsum fibre insert
CW stud
Crimp the traverse to the CW studusing a stud crimper
Traverse dimension 620
Stud spacing 625 (grid dimension)
290
Drilling screwLB 35 x 16
Steel anchoringtraverse with gypsum
fibre insert
UA profile Crimped Steel anchoring traversewith gypsum fibre insert
CW stud
eg Handrail
UA profileKnauf boards
Steel anchoring traversewith gypsum fibre insert
eg Handrail
CW studKnauf board
Steel anchoring traversewith gypsum fibre insert
Loads on partitions and furringsAnchoring in the traverses
Note No web cutouts in the CW studs are permissible for traverses to which the CW studs are attached
14
Loads on partitions and furringsAnchoring in the traverses
Knauf steel anchoring traverseThe steel anchoring traverse is suitable for accepting loads attached to the wall up to 10 kNm wall length eg towel holders cupboards shelves and similar Not suitable for dynamic loads such as folding wall attached seatsThe steel anchoring traverse consists of 075 mm thick sheet metal and are crimped onto the side using a stud crimper on the CW studs Particularly suitable for single-layer clad metal stud partitions and furrings where in case of cantilever loads gt 04 kNm (400 kgm) wall length the installation of a traverse is required
NoteTraverses for installation in damp and wet rooms see also system data sheet W38de Knauf Metal Stud Partitions AQUAPANELreg
Installation and applicationCrimp the steel anchoring traverse made of galvanized sheet steel to the CW studs using a Stud CrimperAdditional screw fastening of the steel anchoring traverse via screw fastening of the cladding (min 2 to 3 anchoring points) Reduce the screw spacing of the cladding if necessaryArrangement in a rowCW studs
Scale 110 I Dimensions in mmDetailsW234de-A11 View W234de V11 Vertical section
eg W111de
W234de-H11 Horizontal sectioneg W111de
Sheet metal gauge 075 mm
Steel anchoring traverse
CW stud
Crimp the traverse to the CW studusing the stud crimper
290
Traverse dimension 620
Stud spacing 625 (grid dimension)
eg Cabinet
CW stud
Knauf boardSteel anchoring traverse
Steel anchoring traverseCW stud
Crimped
Note No web cutouts in the CW studs are permissible for traverses to which the CW studs are attached
15
Full-length SanistandFloor-to-ceiling Sanistands made of galvanized UA profiles (min UA 75) 2 mm thick are suitable for transferring loads from traverses into the supporting structure or for fixing loads hanging onto walls such as school blackboards up to 15 kNm wall lengthFloor-to-ceiling Sanistands profiles are anchored to the basic floor and ceiling with door frame brackets or connection brackets for UA profiles The upper door frame bracket includes openings for routing cables such as pipe-in-pipe systems or electrical cablesThe loads are connected directly to the flange of the UA profile
W228de-A10 View
le 1000 mm
UW runnercontinuous
Door frameconnection brackettop connection withenclosed dowels
CW studAxial spacing suitedto partition system
UA profileas afloor-to-ceilingSanistand forbearing cantileverloads
UW runnercontinuous
Door frameconnection bracketbottom connectionwith enclosed dowels
Scale 110
Installation and applicationFloor-to-ceiling Sanistands made of UA profiles must be anchored to the basic floor and ceiling with door frame brackets or connection brackets for UA profiles The upper door frame bracket includes openings for routing cables such as pipe-in-pipe systems or electrical cables Fasten objects to UA profiles using threaded rods U washers and M1012 steel nuts or self-tapping screws
Loads on partitions and furringsFull-length Sanistand
Detail
Notes
Web cutouts are not permissible in UA Sanistand subject to cantilever loads point loads or linear distributed loadsMaximum screw load with connections to full height Sanistand (UA profile)Every UA profile flange and anchoring point may not exceed a resulting pull-out load of 150 kN (150 kg)Components similar to cantilevers such as foldable rails should be screwed onto two adjacent UA profilesUse suitable drilling screws eg Ejot Zebra Piasta Hilti S-MD or comparable
16
Loads on partitions and furringsFull-length Sanistand
Scale 110DetailsW116de-V1 Sanistand W116de-H1 SanistandVertical section I Without fire resistance Horizontal section I Without fire resistance
UW runnerUniflott + Trenn-Fix
UW runner
Additional UA profile
Sanistand withconcealed mount cistern
Knauf connectionbracket with enclosedM8 carriage bolts
Knauf conection bracket withenclosed M8 carriage bolt
2x 125 mm DiamantDiamant screw XTB
Additional CW stud
Knauf sealing tape
Board strip installationacc to W11de systemdata sheet
Stud spacing le 625 mm
CW stud profile
Additional CW studBoard strip installation in acc with W11de system data sheet
Knauf connection bracket withenclosed M8 carriage bolts
Additional UA profileSanitand with concealedmount cistern
Notes
Max partition height UA 50 = 300 m UA 75 = see system data sheet W11de Knauf Metal Stud Partition for the wall heights
Minimum cladding ge 18 mm Knauf Boards recommendation 2x 125 mm Knauf Diamant
Web cutouts are not permissible in UA Sanistand subject to cantilever loads point loads or linear distributed loadsObserve the manufacturersrsquo details for lateral UA profiles and cladding Additional UA profiles are required laterally on Sanistand mounts acc to DIN 18340 section 374 Only possible without additional UA profiles if the manufacturer of the Sanistand base or WC Sanistand permits itDeviating specifications of the Sanistand manufacturer must be considered and observed
17
Loads on partitions and furringsFull-length Sanistand
Notes
Max partition height rear W112de UA 50 = 300 m UA 75 = see system data sheet W11de Knauf Metal Stud Partition for the wall heights
Minimum cladding front wall installations ge 18 mm Knauf Boards recommendation 2x 125 mm Knauf Diamant
Web cutouts are not permissible in UA Sanistand subject to cantilever loads point loads or linear distributed loadsObserve the manufacturersrsquo details for lateral UA profiles and cladding Additional UA profiles are required laterally on Sanistand mounts acc to DIN 18340 section 374 Only possible without additional UA profiles if the manufacturer of the Sanistand base or WC Sanistand permits itDeviating specifications of the Sanistand manufacturer must be considered and observed
Scale 110DetailsW626Vde-V1 Without back anchoring W626Vde-H1 Without back anchoring Vertical section Horizontal section
UW runnerUniflott + Trenn-Fix
UW runner
Additional UA profile
Sanistand withconcealed mount cistern
Knauf connection bracket withenclosed M8 carriage bolt
Knauf connection bracket withenclosed M8 carriage bolt
2x 125 mm DiamantDiamant screw XTB
Knauf sealing tape
Sanistand withconcealed mount cisternKnauf connection bracket with
enclosed M8 carriage bolts
Stud spacing le 625 mm
UW runner
Knauf boardsCW stud
Additional UA profile
18
Loads on partitions and furringsFull-length Sanistand
Scale 110DetailsW626Vde-V2 Back anchoring in traverse W626Vde-H2 Back anchoring in traverse Vertical section Horizontal section
Sanistand withconcealed mount cistern
SealantUD profile made of insulation strips
UW runner
UW runner
UA profile
Knauf multi-purpose screw FN
Uniflott + Trenn-Fix
Multi-purpose traverse 555 300 23 mm
Knauf connection bracket withenclosed M8 carriage bolts
2x 125 mm DiamantDiamant screw XTB
Knauf connection bracket withenclosed M8 carriage bolt
Wall anchor installation acc to WCSanistand manufacturer specifications
Knauf sealing tape
Stud spacing le 625 mm
Multi-purpose traverse555 300 23 mm
UA profile
UA profile
Knauf connection bracket withenclosed M8 carriage bolt
Knauf connectionbracket with enclosedM8 carriage bolt
Wall anchorinstallation acc to
WC Sanistandmanufacturerspecifications
Notes
Max partition height rear W112de UA 50 = 300 m UA 75 = see system data sheet W11de Knauf Metal Stud Partitions for the wall heights
Minimum cladding front wall installations ge 18 mm Knauf Boards recommendation 2x 125 mm Knauf Diamant
Web cutouts are not permissible in UA Sanistand subject to cantilever loads point loads or linear distributed loadsObserve the manufacturersrsquo details for lateral UA profiles and cladding Additional UA profiles are required laterally on Sanistand mounts acc to DIN 18340 section 374 Only possible without additional UA profiles if the manufacturer of the Sanistand base or WC Sanistand permits itDeviating specifications of the Sanistand manufacturer must be considered and observed
19
Loads on partitions and furringsFull-length Sanistand
Scale 110DetailsW626Vde-V3 Back anchoring in UA profile W626Vde-H3 Back anchoring in UA profile Vertical section Horizontal section
Sanistand withconcealed mount cistern
SealantUD profile on insulation strips
UW runner
UW runner
Additional UA profile
Knauf multi-purpose screw FN
Uniflott + Trenn-Fix
UA profile
Knauf connection bracket withenclosed M8 carriage bolts
2x 125 mm DiamantDiamant screw XTB
Knauf connection bracket withenclosed M8 carriage bolts
Fixing bolts with nuts andwashers
Knauf sealing tape
Stud spacing le 625 mm
Additional UA profile
UA profile Fixing bolts with nutsand washers
Knauf connection bracket withenclosed M8 carriage bolts
Knauf connectionbracket with enclosedM8 carriage bolts
Notes
Max partition height at rear W112de UA 50 = 300 m UA 75 = see system data sheet W11de Knauf Metal Stud Partition for the wall heights
Minimum cladding front wall installations ge 18 mm Knauf Boards recommendation 2x 125 mm Knauf Diamant
Web cutouts are not permissible in UA Sanistand subject to cantilever loads point loads or linear distributed loadsObserve the manufacturersrsquo details for lateral UA profiles and cladding Additional UA profiles are required laterally on Sanistand mounts acc to DIN 18340 section 374 Only possible without additional UA profiles if the manufacturer of the Sanistand base or WC Sanistand permits itDeviating specifications of the Sanistand manufacturer must be considered and observed
20
Loads on partitions and furringsFull-length Sanistand
Scale 110DetailsW626Vde-V4 Back anchoring in mounting rail W626Vde-H4 Back anchoring in mounting rail Vertical section Horizontal section
Sanistand withconcealed mount cistern
2x 125 mm Diamant
SealantUD profile on insulation strips
UW runner
Diamant screw XTB
UA profile
Knauf multi-purpose screw FN
Mounting rail with fixing screw
Knauf connection bracket withenclosed M8 carriage bolt
Uniflott + Trenn-Fix
UA profile
Knauf connection bracket withenclosed M8 carriage bolt
Knauf sealing tapeUW runner
Stud spacing le 625 mm
UA profile
UA profile
Mounting railFixing screw
Mounting screw
Sanistand withconcealed mount cistern
Knauf connection bracket withenclosed M8 carriage bolt
Knauf connectionbracket with enclosedM8 carriage bolt
Notes
Max partition height rear W112de UA 50 = 300 m UA 75 = see system data sheet W11de Knauf Metal Stud Partitions for the wall heights
Minimum cladding front wall installations ge 18 mm Knauf Boards recommendation 2x 125 mm Knauf Diamant
Web cutouts are not permissible in UA Sanistand subject to cantilever loads point loads or linear distributed loadsObserve the manufacturersrsquo details for lateral UA profiles and cladding Additional UA profiles are required laterally on Sanistand mounts acc to DIN 18340 section 374 Only possible without additional UA profiles if the manufacturer of the Sanistand base or WC Sanistand permits itDeviating specifications of the Sanistand manufacturer must be considered and observed
21
Notes
In case of load attachment to ldquomulti-level ceiling systemsrdquo refer to the respective valid Knauf system data sheetsIn case of attachment of loads to free-spanning ceilings see system data sheet D13de Knauf Free-Spanning Ceilings
Attachment of loads to Knauf board ceilingsAdditional loads eg lighting fixtures curtain rails and similar can be fixed to Knauf board ceilings using universal dowels cavity dowels spring toggle dowels or Knauf Hartmut Hohlraumduumlbel cavity dowelsAdditional loads must be considered when determining the load class
NoteHeavy loads must be attached directly on load-bearing building elements (basic ceiling) or on auxiliary constructions eg traverses
For each area under load of the Knauf board ceiling the weight of thefastened components may not exceed the following limits
Permissible weight per ceiling area in kgmsup2Without fire resistance With fire resistance1)
15 61)Incaseofapplicationasafireresistanceceilingwithexposedceiling(multi-levelceilingsystem)15kgmsup2totalweightispermissiblefortheexposedceiling(includinginsulationlayerandattachedloads)attachedtothefireresistanceceiling
Furthermore the following conditions applyFor each anchoring point the components fastened to the board ceiling may not exceed the following weights
Fastening method Permissible weight per anchoring point in kgWithout fire resistance With fire resistance
Fastening in the cladding 6 05
Fastening to the grid 10 10
Fastening in the claddingKnauf Hartmut Hohlraumduumlbel cavity dowelScrew M5
Fastening to the gridKnauf Universalschraube FN multi-purpose screw eg curtain rail
The minimum separation spacings between individual attached loads must be observed to avoid local overloading of the ceiling The minimum separation clearance between two attachment points consists of both load radii for the point loadsThe load radius of a point load can be taken from the following diagram in dependence on the permissible weight per unit area for additional loads
Point load in kg
7570656055504540353025201510
0 2 3 4 5 6 7 8 9 10
Radiu
s in c
m
1
50
Fastening in the claddingpossible (without fire resistance)
3 kgmsup2 permissible additional weight (on the exposed ceiling under a fire resistance ceiling refer to the respective valid Knauf system data sheets)6 kgmsup2 permissible additional weight (with fire resistance)15 kgmsup2 permissible additional weight (without fire resistance)
Example fastening scheme at 15 kgmsup2
05 kg
10 kg
3 kgr = 25 cm
r = 46 cm
6 kgr = 355 cm
1 kg
r = 15 cm
r = 105 cm
NoteThe anchored loads can be transferred using several anchoring elements
Loads on board ceilingsFastening in the cladding grid
22
Knauf multi-purpose traversesThe multi-purpose traverse in Knauf board ceilings is suitable for the application of point loads up to 075 kN eg chandeliers music speakers or similarThe multi-purpose traverse consists of a 23 mm thick multi-layer wooden board and galvanized sheet metal profiles It is fastened to the side of the CD furring channelThe attachment of the loads to the traverses should be performed using Knauf Multi-Purpose Screw FNInstallation is possible in a double layer profile grid and flush profile grid
Installation and applicationBend the Daisy chain clip before lateral screw fastening The Daisy chain clip is then Z shaped The unpunched metal side of the Daisy chain clip is pushed onto the lower side of the traverse and then screw fastened laterally through the factory-made hole on the long side of the traverse Screw fasten 4x Daisy chain clips each using one drywall screw TN 35 x 35 about 100 mm from the corner of the multi-layer board on the long edge of the multi-purpose traverse Arrange an additional CD channel (length ge 650 mm) for every long edge in accordance with the width of the multi-purpose traverse Alternately a ceiling furring channel can be used for application of the multi-purpose traverse The supporting profiles are suspended using ceiling suspenders of load class 40 kg The suspenders may not be situated in the direct vicinity of the longitudinal area of the traverse as this will hinder the installation of the traverse Introduce the multi-purpose traverse between the support profiles bend the Daisy chain clip around the CD channel and engage it In case of single-layer cladding do not screw fasten the surface cladding with the multi-purpose traverse
1 Apply the Daisy chain clip 2 Bend the Daisy chain clip 3 Screw fasten the Daisy chain clip
Loads on board ceilingsAnchoring in the traverses
100 mm
23
Loads on board ceilingsAnchoring in the traverses
Scale 110 I Dimensions in mmDetailsD112de SO18 Vertical section ndash Multi-purpose traverse D113de SO12 Vertical section ndash Multi-purpose traverseeg with two additional CD channels I Without fire resistance eg with one additional CD channel I Without fire resistance
D112de SO19 Vertical section ndash Multi-purpose traverse D113de SO13 Vertical section ndash Multi-purpose traverseeg with two additional CD channels I Without fire resistance eg with one additional CD channel I Without fire resistance
D112de SO20 Top view ndash Multi-purpose traverse D113de SO14 Top view ndash Multi-purpose traverseeg with two additional CD channels I Without fire resistance eg with one additional CD channel I Without fire resistance
Fasten Daisy chain clip with drywall screwTN 35 x 35 to multi-purpose traverse
Additional CD channel with two suspendersLoad bearing capacity class ge 040 kN
Multi-purposetraverse555 300 23 mm
300
Furring channel spacing 500
Fasten Daisy chain clip with drywall screwTN 35 x 35 to multi-purpose traverse
Additional suspended load bearing capacity class ge 040 kNMulti-purposetraverse555 300 23 mm
300
Furring channel spacing 500
Additional CD channel with two suspendersLoad bearing capacity class ge 040 kN
Multi-purposetraverse555 300 23 mm
Fasten Daisy chain clip with drywall screwTN 35 x 35 to multi-purpose traverse
Wood panel 555approx
100
Additional suspenderload bearing capacityclass ge 040 kN
Multi-purposetraverse555 300 23 mm
Fasten Daisy chain clip with drywall screwTN 35 x 35 to multi-purpose traverse
Wood panel 555approx
100
Daisy chain clip
Furring channel spacing 500
Traverse
CDchannel
Multi-layerwood panel
Furring channel spacing 500
Multi-purposetraverse
Daisy chain clip
Multi-layerwood panel
Additional grid 4 additional suspension points (eg Nonius suspension)
All technical changes reserved Only the current printed instructions are valid The stated information represents current state-of-the-art Knauf technology The entire state of approved engineering rules appropriate standards guidelines and rules of crafts-manship are not included herewith These and all application instructions have to be adhered to separately by the installer Our warranty is expressly limited to our products in flawless condition All application quantities and delivery amounts are based on empirical data that are not easily transferable to other deviating areasAll rights reserved All amendments reprints and photocopies including those of excerpts require our expressed permission
The stated constructional and structural design specifications and characteristics of building physics of Knauf systems can only be ensured with the exclusive use of Knauf system components or other products expressly recommended by Knauf
Knauf Gips KG Am Bahnhof 7 97346 Iphofen GermanyKnauf DirectTechnical Advisory Service
knauf-direktknaufde
wwwknaufde
VT03deeng09190TI
The iPad App Knauf Infothek now provides all the current information and documents from Knauf Gips KG at any time and in every location in a clear and comfortable wayKnauf Infothek
Videos for Knauf systems and products can be found under the following linkwwwyoutubecomknaufEPD
9
Loads on partitions and furringsAnchoring in the traverses
RatingThe specified permissible cantilever loads are in accordance with the DIN 18183 or DIN 4103-1 at an eccentricity (spacing of resulting load to the wall surface) of max 300 mm The permissible load is reduced accordingly with greater eccentricity The determination of the permissible cantilever loads with divergent eccentricity is undertaken using the tables or diagrams on page 4 and page 5
Rating examples Determination of the permissible cabinet weight as well as the required minimum number of dowels (always ge 2)Metal stud partition W111de CW 50 cladding 18 mm Knauf board acc to tableField of application static load max cantilever load 07 kNm (70 kgm) wall length Cabinet
widthCabinet depthmm
mm 100 200 300 400 500 600400 43 40 37 34 31 28600 645 60 555 51 465 42800 86 80 74 68 62 561000 1075 100 925 85 775 701200 129 120 111 102 93 84
Cabinet depth 500 mm cabinet width 800 mm Max cabinet weight 62 kg Fixing traverse Knauf Multi-Purpose Screw FN 43 x 65
Max screw load 45 kg
Required number of screws 62 kg 45 kg = 14 2 screws
are the min necessary
Metal stud partition W111de UA 75 cladding 15 mm Diamant GKFI acc to diagram
Field of application dynamic load max cantilever load 15 kNm (150 kgm) wall length
20
400
Cabinet depth100 200 600
Max permissible cabinet weight
140120
80
4060
kg
200
160
180
Cabinet width
mm
1000
1200
600
mm 300
100 800
240220
260280300320340
450400 500
165
1
23
Cabinet depth 450 mm cabinet width 800 mm
With cabinet depth 450 mm 1 vertically upwards up to the cabinet width line 800 mm
2 at the intersection point horizontal to the left read off value 3
Max cabinet weight 165 kg
Multi-purpose traverse Knauf Multi-Purpose Screw FN 43 x 65
Max screw load 125 kg
Required number of screws 165 kg 125 kg = 13 2 screws
are the min necessary
10
Knauf multi-purpose traversesThe multi-purpose traverse is suitable for accepting loads attached to the wall up to 15 kNm wall length eg cupboards boilers folding wall attached seats folding handles and similarThe multi-purpose traverse consists of a 23 mm thick multi-layer wooden board and galvanized sheet metal profiles It is fastened to the side of the floor-to-ceiling profilesThe attachment of the loads to the traverses should be performed using Knauf Multi-Purpose Screw FN
NoteTraverses for installation in damp and wet rooms see also system data sheet W38de Knauf Metal Stud Partitions AQUAPANELreg
Loads on partitions and furringsAnchoring in the traverses
Installation and applicationMulti-purpose traverse made of multi-layer wooden board and galvanized sheet metal profiles attached to the side of the CW studs UA profiles For CW studs screw fasten using the 6 enclosed Metal Screws LN 35 x 11 mm (3 per side) For UA profiles screw fasten with the 6 enclosed Drilling Screws ST 42 x 13 mm (3 per side)Arrangement in a rowUA profiles CW studs
Direction of installation Direction of installation
11
Loads on partitions and furringsAnchoring in the traverses
W234de-A10 View ndash Design with UA profile W234de-A13 View ndash Design with CW stud
W234de-H10 Horizontal section ndash Design with UA profile W234de-H13 Horizontal section ndash Design with CW studeg W626de eg W626de
W234de-V10 Vertical section ndash Design with UA profile W234de-V13 Vertical section ndash Design with CW studeg W116de eg W112de
Wooden board 555
Stud spacing 625 (grid dimension)
300
Multi-purpose traverse555 300 23 mm
Multi-layer wooden board
UA profile
Drillingscrew ST42 x 13(enclosed)
Wooden board 555
Stud spacing 625 (grid dimension)
300 Metal screw
LN 35 x 11(enclosed)
Multi-purpose traverse555 300 23 mm
Multi-layer wooden board
CW stud
Wooden board 555
Stud spacing 625 (grid dimension)
300
Multi-purpose traverse555 300 23 mm
UA profileDrilling screwST 42 x 13
Multi-purpose traverse555 300 23 mm
CW studMetal screwLN 35 x 11
48
eg folding wallattached seat
Knauf boardstrips
eg Supporthandle maxprojection 800 mm
Multi-purposetraverseUA profileKnauf boards
48
Multi-purposetraverseCW studKnauf boards
eg Cabinet
Scale 110 I Dimensions in mmDetails
Note No web cutouts in the CW studs are permissible for traverses to which the CW studs are attached
12
Knauf steel anchoring traverse with gypsum fibre insertThe steel anchoring traverse with gypsum fibre insert is suitable for accepting loads attached to the wall up to 15 kNm wall length eg cupboards shelves handrails and similarThe metal traverse with gypsum fibre insert consists of 075 mm thick sheet metal as well as an 18 mm thick gypsum fibre board It is fastened to the side of the floor-to-ceiling profiles The attachment of the loads to the traverses should be performed using Knauf Multi-Purpose Screw FNUse in partition systems where the requirement for non-combustible reaction to fire exists
Installation and applicationSteel anchoring traverse made of galvanized steel with gypsum fibre insert fastened to the CW studs UA profiles In case of CW studs crimp using a Stud Crimper and for UA profiles screw fasten with 6 Drilling screws LB 35 x 16 mmArrangement in a rowUA profiles CW studs
Loads on partitions and furringsAnchoring in the traverses
13
Scale 110 I Dimensions in mmDetailsW234de-A12 View - Design with UA profile W234de-A14 View - Design with CW stud
W234de-H12 Horizontal section - Design with UA profile W234de-H14 Horizontal section - Design with CW studeg W112de eg W112de
W234de-V12 Vertical section - Design with UA profile W234de-V14 Vertical section - Design with CW studeg W112de eg W112de
Traverse dimension 620
Stud spacing 625 (grid dimension)
290
Steel anchoring traversewith gypsum fibre insert
Traverse attached to UA profileusing drilling screws
UA profile
Steel anchoring traversewith gypsum fibre insert
CW stud
Crimp the traverse to the CW studusing a stud crimper
Traverse dimension 620
Stud spacing 625 (grid dimension)
290
Drilling screwLB 35 x 16
Steel anchoringtraverse with gypsum
fibre insert
UA profile Crimped Steel anchoring traversewith gypsum fibre insert
CW stud
eg Handrail
UA profileKnauf boards
Steel anchoring traversewith gypsum fibre insert
eg Handrail
CW studKnauf board
Steel anchoring traversewith gypsum fibre insert
Loads on partitions and furringsAnchoring in the traverses
Note No web cutouts in the CW studs are permissible for traverses to which the CW studs are attached
14
Loads on partitions and furringsAnchoring in the traverses
Knauf steel anchoring traverseThe steel anchoring traverse is suitable for accepting loads attached to the wall up to 10 kNm wall length eg towel holders cupboards shelves and similar Not suitable for dynamic loads such as folding wall attached seatsThe steel anchoring traverse consists of 075 mm thick sheet metal and are crimped onto the side using a stud crimper on the CW studs Particularly suitable for single-layer clad metal stud partitions and furrings where in case of cantilever loads gt 04 kNm (400 kgm) wall length the installation of a traverse is required
NoteTraverses for installation in damp and wet rooms see also system data sheet W38de Knauf Metal Stud Partitions AQUAPANELreg
Installation and applicationCrimp the steel anchoring traverse made of galvanized sheet steel to the CW studs using a Stud CrimperAdditional screw fastening of the steel anchoring traverse via screw fastening of the cladding (min 2 to 3 anchoring points) Reduce the screw spacing of the cladding if necessaryArrangement in a rowCW studs
Scale 110 I Dimensions in mmDetailsW234de-A11 View W234de V11 Vertical section
eg W111de
W234de-H11 Horizontal sectioneg W111de
Sheet metal gauge 075 mm
Steel anchoring traverse
CW stud
Crimp the traverse to the CW studusing the stud crimper
290
Traverse dimension 620
Stud spacing 625 (grid dimension)
eg Cabinet
CW stud
Knauf boardSteel anchoring traverse
Steel anchoring traverseCW stud
Crimped
Note No web cutouts in the CW studs are permissible for traverses to which the CW studs are attached
15
Full-length SanistandFloor-to-ceiling Sanistands made of galvanized UA profiles (min UA 75) 2 mm thick are suitable for transferring loads from traverses into the supporting structure or for fixing loads hanging onto walls such as school blackboards up to 15 kNm wall lengthFloor-to-ceiling Sanistands profiles are anchored to the basic floor and ceiling with door frame brackets or connection brackets for UA profiles The upper door frame bracket includes openings for routing cables such as pipe-in-pipe systems or electrical cablesThe loads are connected directly to the flange of the UA profile
W228de-A10 View
le 1000 mm
UW runnercontinuous
Door frameconnection brackettop connection withenclosed dowels
CW studAxial spacing suitedto partition system
UA profileas afloor-to-ceilingSanistand forbearing cantileverloads
UW runnercontinuous
Door frameconnection bracketbottom connectionwith enclosed dowels
Scale 110
Installation and applicationFloor-to-ceiling Sanistands made of UA profiles must be anchored to the basic floor and ceiling with door frame brackets or connection brackets for UA profiles The upper door frame bracket includes openings for routing cables such as pipe-in-pipe systems or electrical cables Fasten objects to UA profiles using threaded rods U washers and M1012 steel nuts or self-tapping screws
Loads on partitions and furringsFull-length Sanistand
Detail
Notes
Web cutouts are not permissible in UA Sanistand subject to cantilever loads point loads or linear distributed loadsMaximum screw load with connections to full height Sanistand (UA profile)Every UA profile flange and anchoring point may not exceed a resulting pull-out load of 150 kN (150 kg)Components similar to cantilevers such as foldable rails should be screwed onto two adjacent UA profilesUse suitable drilling screws eg Ejot Zebra Piasta Hilti S-MD or comparable
16
Loads on partitions and furringsFull-length Sanistand
Scale 110DetailsW116de-V1 Sanistand W116de-H1 SanistandVertical section I Without fire resistance Horizontal section I Without fire resistance
UW runnerUniflott + Trenn-Fix
UW runner
Additional UA profile
Sanistand withconcealed mount cistern
Knauf connectionbracket with enclosedM8 carriage bolts
Knauf conection bracket withenclosed M8 carriage bolt
2x 125 mm DiamantDiamant screw XTB
Additional CW stud
Knauf sealing tape
Board strip installationacc to W11de systemdata sheet
Stud spacing le 625 mm
CW stud profile
Additional CW studBoard strip installation in acc with W11de system data sheet
Knauf connection bracket withenclosed M8 carriage bolts
Additional UA profileSanitand with concealedmount cistern
Notes
Max partition height UA 50 = 300 m UA 75 = see system data sheet W11de Knauf Metal Stud Partition for the wall heights
Minimum cladding ge 18 mm Knauf Boards recommendation 2x 125 mm Knauf Diamant
Web cutouts are not permissible in UA Sanistand subject to cantilever loads point loads or linear distributed loadsObserve the manufacturersrsquo details for lateral UA profiles and cladding Additional UA profiles are required laterally on Sanistand mounts acc to DIN 18340 section 374 Only possible without additional UA profiles if the manufacturer of the Sanistand base or WC Sanistand permits itDeviating specifications of the Sanistand manufacturer must be considered and observed
17
Loads on partitions and furringsFull-length Sanistand
Notes
Max partition height rear W112de UA 50 = 300 m UA 75 = see system data sheet W11de Knauf Metal Stud Partition for the wall heights
Minimum cladding front wall installations ge 18 mm Knauf Boards recommendation 2x 125 mm Knauf Diamant
Web cutouts are not permissible in UA Sanistand subject to cantilever loads point loads or linear distributed loadsObserve the manufacturersrsquo details for lateral UA profiles and cladding Additional UA profiles are required laterally on Sanistand mounts acc to DIN 18340 section 374 Only possible without additional UA profiles if the manufacturer of the Sanistand base or WC Sanistand permits itDeviating specifications of the Sanistand manufacturer must be considered and observed
Scale 110DetailsW626Vde-V1 Without back anchoring W626Vde-H1 Without back anchoring Vertical section Horizontal section
UW runnerUniflott + Trenn-Fix
UW runner
Additional UA profile
Sanistand withconcealed mount cistern
Knauf connection bracket withenclosed M8 carriage bolt
Knauf connection bracket withenclosed M8 carriage bolt
2x 125 mm DiamantDiamant screw XTB
Knauf sealing tape
Sanistand withconcealed mount cisternKnauf connection bracket with
enclosed M8 carriage bolts
Stud spacing le 625 mm
UW runner
Knauf boardsCW stud
Additional UA profile
18
Loads on partitions and furringsFull-length Sanistand
Scale 110DetailsW626Vde-V2 Back anchoring in traverse W626Vde-H2 Back anchoring in traverse Vertical section Horizontal section
Sanistand withconcealed mount cistern
SealantUD profile made of insulation strips
UW runner
UW runner
UA profile
Knauf multi-purpose screw FN
Uniflott + Trenn-Fix
Multi-purpose traverse 555 300 23 mm
Knauf connection bracket withenclosed M8 carriage bolts
2x 125 mm DiamantDiamant screw XTB
Knauf connection bracket withenclosed M8 carriage bolt
Wall anchor installation acc to WCSanistand manufacturer specifications
Knauf sealing tape
Stud spacing le 625 mm
Multi-purpose traverse555 300 23 mm
UA profile
UA profile
Knauf connection bracket withenclosed M8 carriage bolt
Knauf connectionbracket with enclosedM8 carriage bolt
Wall anchorinstallation acc to
WC Sanistandmanufacturerspecifications
Notes
Max partition height rear W112de UA 50 = 300 m UA 75 = see system data sheet W11de Knauf Metal Stud Partitions for the wall heights
Minimum cladding front wall installations ge 18 mm Knauf Boards recommendation 2x 125 mm Knauf Diamant
Web cutouts are not permissible in UA Sanistand subject to cantilever loads point loads or linear distributed loadsObserve the manufacturersrsquo details for lateral UA profiles and cladding Additional UA profiles are required laterally on Sanistand mounts acc to DIN 18340 section 374 Only possible without additional UA profiles if the manufacturer of the Sanistand base or WC Sanistand permits itDeviating specifications of the Sanistand manufacturer must be considered and observed
19
Loads on partitions and furringsFull-length Sanistand
Scale 110DetailsW626Vde-V3 Back anchoring in UA profile W626Vde-H3 Back anchoring in UA profile Vertical section Horizontal section
Sanistand withconcealed mount cistern
SealantUD profile on insulation strips
UW runner
UW runner
Additional UA profile
Knauf multi-purpose screw FN
Uniflott + Trenn-Fix
UA profile
Knauf connection bracket withenclosed M8 carriage bolts
2x 125 mm DiamantDiamant screw XTB
Knauf connection bracket withenclosed M8 carriage bolts
Fixing bolts with nuts andwashers
Knauf sealing tape
Stud spacing le 625 mm
Additional UA profile
UA profile Fixing bolts with nutsand washers
Knauf connection bracket withenclosed M8 carriage bolts
Knauf connectionbracket with enclosedM8 carriage bolts
Notes
Max partition height at rear W112de UA 50 = 300 m UA 75 = see system data sheet W11de Knauf Metal Stud Partition for the wall heights
Minimum cladding front wall installations ge 18 mm Knauf Boards recommendation 2x 125 mm Knauf Diamant
Web cutouts are not permissible in UA Sanistand subject to cantilever loads point loads or linear distributed loadsObserve the manufacturersrsquo details for lateral UA profiles and cladding Additional UA profiles are required laterally on Sanistand mounts acc to DIN 18340 section 374 Only possible without additional UA profiles if the manufacturer of the Sanistand base or WC Sanistand permits itDeviating specifications of the Sanistand manufacturer must be considered and observed
20
Loads on partitions and furringsFull-length Sanistand
Scale 110DetailsW626Vde-V4 Back anchoring in mounting rail W626Vde-H4 Back anchoring in mounting rail Vertical section Horizontal section
Sanistand withconcealed mount cistern
2x 125 mm Diamant
SealantUD profile on insulation strips
UW runner
Diamant screw XTB
UA profile
Knauf multi-purpose screw FN
Mounting rail with fixing screw
Knauf connection bracket withenclosed M8 carriage bolt
Uniflott + Trenn-Fix
UA profile
Knauf connection bracket withenclosed M8 carriage bolt
Knauf sealing tapeUW runner
Stud spacing le 625 mm
UA profile
UA profile
Mounting railFixing screw
Mounting screw
Sanistand withconcealed mount cistern
Knauf connection bracket withenclosed M8 carriage bolt
Knauf connectionbracket with enclosedM8 carriage bolt
Notes
Max partition height rear W112de UA 50 = 300 m UA 75 = see system data sheet W11de Knauf Metal Stud Partitions for the wall heights
Minimum cladding front wall installations ge 18 mm Knauf Boards recommendation 2x 125 mm Knauf Diamant
Web cutouts are not permissible in UA Sanistand subject to cantilever loads point loads or linear distributed loadsObserve the manufacturersrsquo details for lateral UA profiles and cladding Additional UA profiles are required laterally on Sanistand mounts acc to DIN 18340 section 374 Only possible without additional UA profiles if the manufacturer of the Sanistand base or WC Sanistand permits itDeviating specifications of the Sanistand manufacturer must be considered and observed
21
Notes
In case of load attachment to ldquomulti-level ceiling systemsrdquo refer to the respective valid Knauf system data sheetsIn case of attachment of loads to free-spanning ceilings see system data sheet D13de Knauf Free-Spanning Ceilings
Attachment of loads to Knauf board ceilingsAdditional loads eg lighting fixtures curtain rails and similar can be fixed to Knauf board ceilings using universal dowels cavity dowels spring toggle dowels or Knauf Hartmut Hohlraumduumlbel cavity dowelsAdditional loads must be considered when determining the load class
NoteHeavy loads must be attached directly on load-bearing building elements (basic ceiling) or on auxiliary constructions eg traverses
For each area under load of the Knauf board ceiling the weight of thefastened components may not exceed the following limits
Permissible weight per ceiling area in kgmsup2Without fire resistance With fire resistance1)
15 61)Incaseofapplicationasafireresistanceceilingwithexposedceiling(multi-levelceilingsystem)15kgmsup2totalweightispermissiblefortheexposedceiling(includinginsulationlayerandattachedloads)attachedtothefireresistanceceiling
Furthermore the following conditions applyFor each anchoring point the components fastened to the board ceiling may not exceed the following weights
Fastening method Permissible weight per anchoring point in kgWithout fire resistance With fire resistance
Fastening in the cladding 6 05
Fastening to the grid 10 10
Fastening in the claddingKnauf Hartmut Hohlraumduumlbel cavity dowelScrew M5
Fastening to the gridKnauf Universalschraube FN multi-purpose screw eg curtain rail
The minimum separation spacings between individual attached loads must be observed to avoid local overloading of the ceiling The minimum separation clearance between two attachment points consists of both load radii for the point loadsThe load radius of a point load can be taken from the following diagram in dependence on the permissible weight per unit area for additional loads
Point load in kg
7570656055504540353025201510
0 2 3 4 5 6 7 8 9 10
Radiu
s in c
m
1
50
Fastening in the claddingpossible (without fire resistance)
3 kgmsup2 permissible additional weight (on the exposed ceiling under a fire resistance ceiling refer to the respective valid Knauf system data sheets)6 kgmsup2 permissible additional weight (with fire resistance)15 kgmsup2 permissible additional weight (without fire resistance)
Example fastening scheme at 15 kgmsup2
05 kg
10 kg
3 kgr = 25 cm
r = 46 cm
6 kgr = 355 cm
1 kg
r = 15 cm
r = 105 cm
NoteThe anchored loads can be transferred using several anchoring elements
Loads on board ceilingsFastening in the cladding grid
22
Knauf multi-purpose traversesThe multi-purpose traverse in Knauf board ceilings is suitable for the application of point loads up to 075 kN eg chandeliers music speakers or similarThe multi-purpose traverse consists of a 23 mm thick multi-layer wooden board and galvanized sheet metal profiles It is fastened to the side of the CD furring channelThe attachment of the loads to the traverses should be performed using Knauf Multi-Purpose Screw FNInstallation is possible in a double layer profile grid and flush profile grid
Installation and applicationBend the Daisy chain clip before lateral screw fastening The Daisy chain clip is then Z shaped The unpunched metal side of the Daisy chain clip is pushed onto the lower side of the traverse and then screw fastened laterally through the factory-made hole on the long side of the traverse Screw fasten 4x Daisy chain clips each using one drywall screw TN 35 x 35 about 100 mm from the corner of the multi-layer board on the long edge of the multi-purpose traverse Arrange an additional CD channel (length ge 650 mm) for every long edge in accordance with the width of the multi-purpose traverse Alternately a ceiling furring channel can be used for application of the multi-purpose traverse The supporting profiles are suspended using ceiling suspenders of load class 40 kg The suspenders may not be situated in the direct vicinity of the longitudinal area of the traverse as this will hinder the installation of the traverse Introduce the multi-purpose traverse between the support profiles bend the Daisy chain clip around the CD channel and engage it In case of single-layer cladding do not screw fasten the surface cladding with the multi-purpose traverse
1 Apply the Daisy chain clip 2 Bend the Daisy chain clip 3 Screw fasten the Daisy chain clip
Loads on board ceilingsAnchoring in the traverses
100 mm
23
Loads on board ceilingsAnchoring in the traverses
Scale 110 I Dimensions in mmDetailsD112de SO18 Vertical section ndash Multi-purpose traverse D113de SO12 Vertical section ndash Multi-purpose traverseeg with two additional CD channels I Without fire resistance eg with one additional CD channel I Without fire resistance
D112de SO19 Vertical section ndash Multi-purpose traverse D113de SO13 Vertical section ndash Multi-purpose traverseeg with two additional CD channels I Without fire resistance eg with one additional CD channel I Without fire resistance
D112de SO20 Top view ndash Multi-purpose traverse D113de SO14 Top view ndash Multi-purpose traverseeg with two additional CD channels I Without fire resistance eg with one additional CD channel I Without fire resistance
Fasten Daisy chain clip with drywall screwTN 35 x 35 to multi-purpose traverse
Additional CD channel with two suspendersLoad bearing capacity class ge 040 kN
Multi-purposetraverse555 300 23 mm
300
Furring channel spacing 500
Fasten Daisy chain clip with drywall screwTN 35 x 35 to multi-purpose traverse
Additional suspended load bearing capacity class ge 040 kNMulti-purposetraverse555 300 23 mm
300
Furring channel spacing 500
Additional CD channel with two suspendersLoad bearing capacity class ge 040 kN
Multi-purposetraverse555 300 23 mm
Fasten Daisy chain clip with drywall screwTN 35 x 35 to multi-purpose traverse
Wood panel 555approx
100
Additional suspenderload bearing capacityclass ge 040 kN
Multi-purposetraverse555 300 23 mm
Fasten Daisy chain clip with drywall screwTN 35 x 35 to multi-purpose traverse
Wood panel 555approx
100
Daisy chain clip
Furring channel spacing 500
Traverse
CDchannel
Multi-layerwood panel
Furring channel spacing 500
Multi-purposetraverse
Daisy chain clip
Multi-layerwood panel
Additional grid 4 additional suspension points (eg Nonius suspension)
All technical changes reserved Only the current printed instructions are valid The stated information represents current state-of-the-art Knauf technology The entire state of approved engineering rules appropriate standards guidelines and rules of crafts-manship are not included herewith These and all application instructions have to be adhered to separately by the installer Our warranty is expressly limited to our products in flawless condition All application quantities and delivery amounts are based on empirical data that are not easily transferable to other deviating areasAll rights reserved All amendments reprints and photocopies including those of excerpts require our expressed permission
The stated constructional and structural design specifications and characteristics of building physics of Knauf systems can only be ensured with the exclusive use of Knauf system components or other products expressly recommended by Knauf
Knauf Gips KG Am Bahnhof 7 97346 Iphofen GermanyKnauf DirectTechnical Advisory Service
knauf-direktknaufde
wwwknaufde
VT03deeng09190TI
The iPad App Knauf Infothek now provides all the current information and documents from Knauf Gips KG at any time and in every location in a clear and comfortable wayKnauf Infothek
Videos for Knauf systems and products can be found under the following linkwwwyoutubecomknaufEPD
10
Knauf multi-purpose traversesThe multi-purpose traverse is suitable for accepting loads attached to the wall up to 15 kNm wall length eg cupboards boilers folding wall attached seats folding handles and similarThe multi-purpose traverse consists of a 23 mm thick multi-layer wooden board and galvanized sheet metal profiles It is fastened to the side of the floor-to-ceiling profilesThe attachment of the loads to the traverses should be performed using Knauf Multi-Purpose Screw FN
NoteTraverses for installation in damp and wet rooms see also system data sheet W38de Knauf Metal Stud Partitions AQUAPANELreg
Loads on partitions and furringsAnchoring in the traverses
Installation and applicationMulti-purpose traverse made of multi-layer wooden board and galvanized sheet metal profiles attached to the side of the CW studs UA profiles For CW studs screw fasten using the 6 enclosed Metal Screws LN 35 x 11 mm (3 per side) For UA profiles screw fasten with the 6 enclosed Drilling Screws ST 42 x 13 mm (3 per side)Arrangement in a rowUA profiles CW studs
Direction of installation Direction of installation
11
Loads on partitions and furringsAnchoring in the traverses
W234de-A10 View ndash Design with UA profile W234de-A13 View ndash Design with CW stud
W234de-H10 Horizontal section ndash Design with UA profile W234de-H13 Horizontal section ndash Design with CW studeg W626de eg W626de
W234de-V10 Vertical section ndash Design with UA profile W234de-V13 Vertical section ndash Design with CW studeg W116de eg W112de
Wooden board 555
Stud spacing 625 (grid dimension)
300
Multi-purpose traverse555 300 23 mm
Multi-layer wooden board
UA profile
Drillingscrew ST42 x 13(enclosed)
Wooden board 555
Stud spacing 625 (grid dimension)
300 Metal screw
LN 35 x 11(enclosed)
Multi-purpose traverse555 300 23 mm
Multi-layer wooden board
CW stud
Wooden board 555
Stud spacing 625 (grid dimension)
300
Multi-purpose traverse555 300 23 mm
UA profileDrilling screwST 42 x 13
Multi-purpose traverse555 300 23 mm
CW studMetal screwLN 35 x 11
48
eg folding wallattached seat
Knauf boardstrips
eg Supporthandle maxprojection 800 mm
Multi-purposetraverseUA profileKnauf boards
48
Multi-purposetraverseCW studKnauf boards
eg Cabinet
Scale 110 I Dimensions in mmDetails
Note No web cutouts in the CW studs are permissible for traverses to which the CW studs are attached
12
Knauf steel anchoring traverse with gypsum fibre insertThe steel anchoring traverse with gypsum fibre insert is suitable for accepting loads attached to the wall up to 15 kNm wall length eg cupboards shelves handrails and similarThe metal traverse with gypsum fibre insert consists of 075 mm thick sheet metal as well as an 18 mm thick gypsum fibre board It is fastened to the side of the floor-to-ceiling profiles The attachment of the loads to the traverses should be performed using Knauf Multi-Purpose Screw FNUse in partition systems where the requirement for non-combustible reaction to fire exists
Installation and applicationSteel anchoring traverse made of galvanized steel with gypsum fibre insert fastened to the CW studs UA profiles In case of CW studs crimp using a Stud Crimper and for UA profiles screw fasten with 6 Drilling screws LB 35 x 16 mmArrangement in a rowUA profiles CW studs
Loads on partitions and furringsAnchoring in the traverses
13
Scale 110 I Dimensions in mmDetailsW234de-A12 View - Design with UA profile W234de-A14 View - Design with CW stud
W234de-H12 Horizontal section - Design with UA profile W234de-H14 Horizontal section - Design with CW studeg W112de eg W112de
W234de-V12 Vertical section - Design with UA profile W234de-V14 Vertical section - Design with CW studeg W112de eg W112de
Traverse dimension 620
Stud spacing 625 (grid dimension)
290
Steel anchoring traversewith gypsum fibre insert
Traverse attached to UA profileusing drilling screws
UA profile
Steel anchoring traversewith gypsum fibre insert
CW stud
Crimp the traverse to the CW studusing a stud crimper
Traverse dimension 620
Stud spacing 625 (grid dimension)
290
Drilling screwLB 35 x 16
Steel anchoringtraverse with gypsum
fibre insert
UA profile Crimped Steel anchoring traversewith gypsum fibre insert
CW stud
eg Handrail
UA profileKnauf boards
Steel anchoring traversewith gypsum fibre insert
eg Handrail
CW studKnauf board
Steel anchoring traversewith gypsum fibre insert
Loads on partitions and furringsAnchoring in the traverses
Note No web cutouts in the CW studs are permissible for traverses to which the CW studs are attached
14
Loads on partitions and furringsAnchoring in the traverses
Knauf steel anchoring traverseThe steel anchoring traverse is suitable for accepting loads attached to the wall up to 10 kNm wall length eg towel holders cupboards shelves and similar Not suitable for dynamic loads such as folding wall attached seatsThe steel anchoring traverse consists of 075 mm thick sheet metal and are crimped onto the side using a stud crimper on the CW studs Particularly suitable for single-layer clad metal stud partitions and furrings where in case of cantilever loads gt 04 kNm (400 kgm) wall length the installation of a traverse is required
NoteTraverses for installation in damp and wet rooms see also system data sheet W38de Knauf Metal Stud Partitions AQUAPANELreg
Installation and applicationCrimp the steel anchoring traverse made of galvanized sheet steel to the CW studs using a Stud CrimperAdditional screw fastening of the steel anchoring traverse via screw fastening of the cladding (min 2 to 3 anchoring points) Reduce the screw spacing of the cladding if necessaryArrangement in a rowCW studs
Scale 110 I Dimensions in mmDetailsW234de-A11 View W234de V11 Vertical section
eg W111de
W234de-H11 Horizontal sectioneg W111de
Sheet metal gauge 075 mm
Steel anchoring traverse
CW stud
Crimp the traverse to the CW studusing the stud crimper
290
Traverse dimension 620
Stud spacing 625 (grid dimension)
eg Cabinet
CW stud
Knauf boardSteel anchoring traverse
Steel anchoring traverseCW stud
Crimped
Note No web cutouts in the CW studs are permissible for traverses to which the CW studs are attached
15
Full-length SanistandFloor-to-ceiling Sanistands made of galvanized UA profiles (min UA 75) 2 mm thick are suitable for transferring loads from traverses into the supporting structure or for fixing loads hanging onto walls such as school blackboards up to 15 kNm wall lengthFloor-to-ceiling Sanistands profiles are anchored to the basic floor and ceiling with door frame brackets or connection brackets for UA profiles The upper door frame bracket includes openings for routing cables such as pipe-in-pipe systems or electrical cablesThe loads are connected directly to the flange of the UA profile
W228de-A10 View
le 1000 mm
UW runnercontinuous
Door frameconnection brackettop connection withenclosed dowels
CW studAxial spacing suitedto partition system
UA profileas afloor-to-ceilingSanistand forbearing cantileverloads
UW runnercontinuous
Door frameconnection bracketbottom connectionwith enclosed dowels
Scale 110
Installation and applicationFloor-to-ceiling Sanistands made of UA profiles must be anchored to the basic floor and ceiling with door frame brackets or connection brackets for UA profiles The upper door frame bracket includes openings for routing cables such as pipe-in-pipe systems or electrical cables Fasten objects to UA profiles using threaded rods U washers and M1012 steel nuts or self-tapping screws
Loads on partitions and furringsFull-length Sanistand
Detail
Notes
Web cutouts are not permissible in UA Sanistand subject to cantilever loads point loads or linear distributed loadsMaximum screw load with connections to full height Sanistand (UA profile)Every UA profile flange and anchoring point may not exceed a resulting pull-out load of 150 kN (150 kg)Components similar to cantilevers such as foldable rails should be screwed onto two adjacent UA profilesUse suitable drilling screws eg Ejot Zebra Piasta Hilti S-MD or comparable
16
Loads on partitions and furringsFull-length Sanistand
Scale 110DetailsW116de-V1 Sanistand W116de-H1 SanistandVertical section I Without fire resistance Horizontal section I Without fire resistance
UW runnerUniflott + Trenn-Fix
UW runner
Additional UA profile
Sanistand withconcealed mount cistern
Knauf connectionbracket with enclosedM8 carriage bolts
Knauf conection bracket withenclosed M8 carriage bolt
2x 125 mm DiamantDiamant screw XTB
Additional CW stud
Knauf sealing tape
Board strip installationacc to W11de systemdata sheet
Stud spacing le 625 mm
CW stud profile
Additional CW studBoard strip installation in acc with W11de system data sheet
Knauf connection bracket withenclosed M8 carriage bolts
Additional UA profileSanitand with concealedmount cistern
Notes
Max partition height UA 50 = 300 m UA 75 = see system data sheet W11de Knauf Metal Stud Partition for the wall heights
Minimum cladding ge 18 mm Knauf Boards recommendation 2x 125 mm Knauf Diamant
Web cutouts are not permissible in UA Sanistand subject to cantilever loads point loads or linear distributed loadsObserve the manufacturersrsquo details for lateral UA profiles and cladding Additional UA profiles are required laterally on Sanistand mounts acc to DIN 18340 section 374 Only possible without additional UA profiles if the manufacturer of the Sanistand base or WC Sanistand permits itDeviating specifications of the Sanistand manufacturer must be considered and observed
17
Loads on partitions and furringsFull-length Sanistand
Notes
Max partition height rear W112de UA 50 = 300 m UA 75 = see system data sheet W11de Knauf Metal Stud Partition for the wall heights
Minimum cladding front wall installations ge 18 mm Knauf Boards recommendation 2x 125 mm Knauf Diamant
Web cutouts are not permissible in UA Sanistand subject to cantilever loads point loads or linear distributed loadsObserve the manufacturersrsquo details for lateral UA profiles and cladding Additional UA profiles are required laterally on Sanistand mounts acc to DIN 18340 section 374 Only possible without additional UA profiles if the manufacturer of the Sanistand base or WC Sanistand permits itDeviating specifications of the Sanistand manufacturer must be considered and observed
Scale 110DetailsW626Vde-V1 Without back anchoring W626Vde-H1 Without back anchoring Vertical section Horizontal section
UW runnerUniflott + Trenn-Fix
UW runner
Additional UA profile
Sanistand withconcealed mount cistern
Knauf connection bracket withenclosed M8 carriage bolt
Knauf connection bracket withenclosed M8 carriage bolt
2x 125 mm DiamantDiamant screw XTB
Knauf sealing tape
Sanistand withconcealed mount cisternKnauf connection bracket with
enclosed M8 carriage bolts
Stud spacing le 625 mm
UW runner
Knauf boardsCW stud
Additional UA profile
18
Loads on partitions and furringsFull-length Sanistand
Scale 110DetailsW626Vde-V2 Back anchoring in traverse W626Vde-H2 Back anchoring in traverse Vertical section Horizontal section
Sanistand withconcealed mount cistern
SealantUD profile made of insulation strips
UW runner
UW runner
UA profile
Knauf multi-purpose screw FN
Uniflott + Trenn-Fix
Multi-purpose traverse 555 300 23 mm
Knauf connection bracket withenclosed M8 carriage bolts
2x 125 mm DiamantDiamant screw XTB
Knauf connection bracket withenclosed M8 carriage bolt
Wall anchor installation acc to WCSanistand manufacturer specifications
Knauf sealing tape
Stud spacing le 625 mm
Multi-purpose traverse555 300 23 mm
UA profile
UA profile
Knauf connection bracket withenclosed M8 carriage bolt
Knauf connectionbracket with enclosedM8 carriage bolt
Wall anchorinstallation acc to
WC Sanistandmanufacturerspecifications
Notes
Max partition height rear W112de UA 50 = 300 m UA 75 = see system data sheet W11de Knauf Metal Stud Partitions for the wall heights
Minimum cladding front wall installations ge 18 mm Knauf Boards recommendation 2x 125 mm Knauf Diamant
Web cutouts are not permissible in UA Sanistand subject to cantilever loads point loads or linear distributed loadsObserve the manufacturersrsquo details for lateral UA profiles and cladding Additional UA profiles are required laterally on Sanistand mounts acc to DIN 18340 section 374 Only possible without additional UA profiles if the manufacturer of the Sanistand base or WC Sanistand permits itDeviating specifications of the Sanistand manufacturer must be considered and observed
19
Loads on partitions and furringsFull-length Sanistand
Scale 110DetailsW626Vde-V3 Back anchoring in UA profile W626Vde-H3 Back anchoring in UA profile Vertical section Horizontal section
Sanistand withconcealed mount cistern
SealantUD profile on insulation strips
UW runner
UW runner
Additional UA profile
Knauf multi-purpose screw FN
Uniflott + Trenn-Fix
UA profile
Knauf connection bracket withenclosed M8 carriage bolts
2x 125 mm DiamantDiamant screw XTB
Knauf connection bracket withenclosed M8 carriage bolts
Fixing bolts with nuts andwashers
Knauf sealing tape
Stud spacing le 625 mm
Additional UA profile
UA profile Fixing bolts with nutsand washers
Knauf connection bracket withenclosed M8 carriage bolts
Knauf connectionbracket with enclosedM8 carriage bolts
Notes
Max partition height at rear W112de UA 50 = 300 m UA 75 = see system data sheet W11de Knauf Metal Stud Partition for the wall heights
Minimum cladding front wall installations ge 18 mm Knauf Boards recommendation 2x 125 mm Knauf Diamant
Web cutouts are not permissible in UA Sanistand subject to cantilever loads point loads or linear distributed loadsObserve the manufacturersrsquo details for lateral UA profiles and cladding Additional UA profiles are required laterally on Sanistand mounts acc to DIN 18340 section 374 Only possible without additional UA profiles if the manufacturer of the Sanistand base or WC Sanistand permits itDeviating specifications of the Sanistand manufacturer must be considered and observed
20
Loads on partitions and furringsFull-length Sanistand
Scale 110DetailsW626Vde-V4 Back anchoring in mounting rail W626Vde-H4 Back anchoring in mounting rail Vertical section Horizontal section
Sanistand withconcealed mount cistern
2x 125 mm Diamant
SealantUD profile on insulation strips
UW runner
Diamant screw XTB
UA profile
Knauf multi-purpose screw FN
Mounting rail with fixing screw
Knauf connection bracket withenclosed M8 carriage bolt
Uniflott + Trenn-Fix
UA profile
Knauf connection bracket withenclosed M8 carriage bolt
Knauf sealing tapeUW runner
Stud spacing le 625 mm
UA profile
UA profile
Mounting railFixing screw
Mounting screw
Sanistand withconcealed mount cistern
Knauf connection bracket withenclosed M8 carriage bolt
Knauf connectionbracket with enclosedM8 carriage bolt
Notes
Max partition height rear W112de UA 50 = 300 m UA 75 = see system data sheet W11de Knauf Metal Stud Partitions for the wall heights
Minimum cladding front wall installations ge 18 mm Knauf Boards recommendation 2x 125 mm Knauf Diamant
Web cutouts are not permissible in UA Sanistand subject to cantilever loads point loads or linear distributed loadsObserve the manufacturersrsquo details for lateral UA profiles and cladding Additional UA profiles are required laterally on Sanistand mounts acc to DIN 18340 section 374 Only possible without additional UA profiles if the manufacturer of the Sanistand base or WC Sanistand permits itDeviating specifications of the Sanistand manufacturer must be considered and observed
21
Notes
In case of load attachment to ldquomulti-level ceiling systemsrdquo refer to the respective valid Knauf system data sheetsIn case of attachment of loads to free-spanning ceilings see system data sheet D13de Knauf Free-Spanning Ceilings
Attachment of loads to Knauf board ceilingsAdditional loads eg lighting fixtures curtain rails and similar can be fixed to Knauf board ceilings using universal dowels cavity dowels spring toggle dowels or Knauf Hartmut Hohlraumduumlbel cavity dowelsAdditional loads must be considered when determining the load class
NoteHeavy loads must be attached directly on load-bearing building elements (basic ceiling) or on auxiliary constructions eg traverses
For each area under load of the Knauf board ceiling the weight of thefastened components may not exceed the following limits
Permissible weight per ceiling area in kgmsup2Without fire resistance With fire resistance1)
15 61)Incaseofapplicationasafireresistanceceilingwithexposedceiling(multi-levelceilingsystem)15kgmsup2totalweightispermissiblefortheexposedceiling(includinginsulationlayerandattachedloads)attachedtothefireresistanceceiling
Furthermore the following conditions applyFor each anchoring point the components fastened to the board ceiling may not exceed the following weights
Fastening method Permissible weight per anchoring point in kgWithout fire resistance With fire resistance
Fastening in the cladding 6 05
Fastening to the grid 10 10
Fastening in the claddingKnauf Hartmut Hohlraumduumlbel cavity dowelScrew M5
Fastening to the gridKnauf Universalschraube FN multi-purpose screw eg curtain rail
The minimum separation spacings between individual attached loads must be observed to avoid local overloading of the ceiling The minimum separation clearance between two attachment points consists of both load radii for the point loadsThe load radius of a point load can be taken from the following diagram in dependence on the permissible weight per unit area for additional loads
Point load in kg
7570656055504540353025201510
0 2 3 4 5 6 7 8 9 10
Radiu
s in c
m
1
50
Fastening in the claddingpossible (without fire resistance)
3 kgmsup2 permissible additional weight (on the exposed ceiling under a fire resistance ceiling refer to the respective valid Knauf system data sheets)6 kgmsup2 permissible additional weight (with fire resistance)15 kgmsup2 permissible additional weight (without fire resistance)
Example fastening scheme at 15 kgmsup2
05 kg
10 kg
3 kgr = 25 cm
r = 46 cm
6 kgr = 355 cm
1 kg
r = 15 cm
r = 105 cm
NoteThe anchored loads can be transferred using several anchoring elements
Loads on board ceilingsFastening in the cladding grid
22
Knauf multi-purpose traversesThe multi-purpose traverse in Knauf board ceilings is suitable for the application of point loads up to 075 kN eg chandeliers music speakers or similarThe multi-purpose traverse consists of a 23 mm thick multi-layer wooden board and galvanized sheet metal profiles It is fastened to the side of the CD furring channelThe attachment of the loads to the traverses should be performed using Knauf Multi-Purpose Screw FNInstallation is possible in a double layer profile grid and flush profile grid
Installation and applicationBend the Daisy chain clip before lateral screw fastening The Daisy chain clip is then Z shaped The unpunched metal side of the Daisy chain clip is pushed onto the lower side of the traverse and then screw fastened laterally through the factory-made hole on the long side of the traverse Screw fasten 4x Daisy chain clips each using one drywall screw TN 35 x 35 about 100 mm from the corner of the multi-layer board on the long edge of the multi-purpose traverse Arrange an additional CD channel (length ge 650 mm) for every long edge in accordance with the width of the multi-purpose traverse Alternately a ceiling furring channel can be used for application of the multi-purpose traverse The supporting profiles are suspended using ceiling suspenders of load class 40 kg The suspenders may not be situated in the direct vicinity of the longitudinal area of the traverse as this will hinder the installation of the traverse Introduce the multi-purpose traverse between the support profiles bend the Daisy chain clip around the CD channel and engage it In case of single-layer cladding do not screw fasten the surface cladding with the multi-purpose traverse
1 Apply the Daisy chain clip 2 Bend the Daisy chain clip 3 Screw fasten the Daisy chain clip
Loads on board ceilingsAnchoring in the traverses
100 mm
23
Loads on board ceilingsAnchoring in the traverses
Scale 110 I Dimensions in mmDetailsD112de SO18 Vertical section ndash Multi-purpose traverse D113de SO12 Vertical section ndash Multi-purpose traverseeg with two additional CD channels I Without fire resistance eg with one additional CD channel I Without fire resistance
D112de SO19 Vertical section ndash Multi-purpose traverse D113de SO13 Vertical section ndash Multi-purpose traverseeg with two additional CD channels I Without fire resistance eg with one additional CD channel I Without fire resistance
D112de SO20 Top view ndash Multi-purpose traverse D113de SO14 Top view ndash Multi-purpose traverseeg with two additional CD channels I Without fire resistance eg with one additional CD channel I Without fire resistance
Fasten Daisy chain clip with drywall screwTN 35 x 35 to multi-purpose traverse
Additional CD channel with two suspendersLoad bearing capacity class ge 040 kN
Multi-purposetraverse555 300 23 mm
300
Furring channel spacing 500
Fasten Daisy chain clip with drywall screwTN 35 x 35 to multi-purpose traverse
Additional suspended load bearing capacity class ge 040 kNMulti-purposetraverse555 300 23 mm
300
Furring channel spacing 500
Additional CD channel with two suspendersLoad bearing capacity class ge 040 kN
Multi-purposetraverse555 300 23 mm
Fasten Daisy chain clip with drywall screwTN 35 x 35 to multi-purpose traverse
Wood panel 555approx
100
Additional suspenderload bearing capacityclass ge 040 kN
Multi-purposetraverse555 300 23 mm
Fasten Daisy chain clip with drywall screwTN 35 x 35 to multi-purpose traverse
Wood panel 555approx
100
Daisy chain clip
Furring channel spacing 500
Traverse
CDchannel
Multi-layerwood panel
Furring channel spacing 500
Multi-purposetraverse
Daisy chain clip
Multi-layerwood panel
Additional grid 4 additional suspension points (eg Nonius suspension)
All technical changes reserved Only the current printed instructions are valid The stated information represents current state-of-the-art Knauf technology The entire state of approved engineering rules appropriate standards guidelines and rules of crafts-manship are not included herewith These and all application instructions have to be adhered to separately by the installer Our warranty is expressly limited to our products in flawless condition All application quantities and delivery amounts are based on empirical data that are not easily transferable to other deviating areasAll rights reserved All amendments reprints and photocopies including those of excerpts require our expressed permission
The stated constructional and structural design specifications and characteristics of building physics of Knauf systems can only be ensured with the exclusive use of Knauf system components or other products expressly recommended by Knauf
Knauf Gips KG Am Bahnhof 7 97346 Iphofen GermanyKnauf DirectTechnical Advisory Service
knauf-direktknaufde
wwwknaufde
VT03deeng09190TI
The iPad App Knauf Infothek now provides all the current information and documents from Knauf Gips KG at any time and in every location in a clear and comfortable wayKnauf Infothek
Videos for Knauf systems and products can be found under the following linkwwwyoutubecomknaufEPD
11
Loads on partitions and furringsAnchoring in the traverses
W234de-A10 View ndash Design with UA profile W234de-A13 View ndash Design with CW stud
W234de-H10 Horizontal section ndash Design with UA profile W234de-H13 Horizontal section ndash Design with CW studeg W626de eg W626de
W234de-V10 Vertical section ndash Design with UA profile W234de-V13 Vertical section ndash Design with CW studeg W116de eg W112de
Wooden board 555
Stud spacing 625 (grid dimension)
300
Multi-purpose traverse555 300 23 mm
Multi-layer wooden board
UA profile
Drillingscrew ST42 x 13(enclosed)
Wooden board 555
Stud spacing 625 (grid dimension)
300 Metal screw
LN 35 x 11(enclosed)
Multi-purpose traverse555 300 23 mm
Multi-layer wooden board
CW stud
Wooden board 555
Stud spacing 625 (grid dimension)
300
Multi-purpose traverse555 300 23 mm
UA profileDrilling screwST 42 x 13
Multi-purpose traverse555 300 23 mm
CW studMetal screwLN 35 x 11
48
eg folding wallattached seat
Knauf boardstrips
eg Supporthandle maxprojection 800 mm
Multi-purposetraverseUA profileKnauf boards
48
Multi-purposetraverseCW studKnauf boards
eg Cabinet
Scale 110 I Dimensions in mmDetails
Note No web cutouts in the CW studs are permissible for traverses to which the CW studs are attached
12
Knauf steel anchoring traverse with gypsum fibre insertThe steel anchoring traverse with gypsum fibre insert is suitable for accepting loads attached to the wall up to 15 kNm wall length eg cupboards shelves handrails and similarThe metal traverse with gypsum fibre insert consists of 075 mm thick sheet metal as well as an 18 mm thick gypsum fibre board It is fastened to the side of the floor-to-ceiling profiles The attachment of the loads to the traverses should be performed using Knauf Multi-Purpose Screw FNUse in partition systems where the requirement for non-combustible reaction to fire exists
Installation and applicationSteel anchoring traverse made of galvanized steel with gypsum fibre insert fastened to the CW studs UA profiles In case of CW studs crimp using a Stud Crimper and for UA profiles screw fasten with 6 Drilling screws LB 35 x 16 mmArrangement in a rowUA profiles CW studs
Loads on partitions and furringsAnchoring in the traverses
13
Scale 110 I Dimensions in mmDetailsW234de-A12 View - Design with UA profile W234de-A14 View - Design with CW stud
W234de-H12 Horizontal section - Design with UA profile W234de-H14 Horizontal section - Design with CW studeg W112de eg W112de
W234de-V12 Vertical section - Design with UA profile W234de-V14 Vertical section - Design with CW studeg W112de eg W112de
Traverse dimension 620
Stud spacing 625 (grid dimension)
290
Steel anchoring traversewith gypsum fibre insert
Traverse attached to UA profileusing drilling screws
UA profile
Steel anchoring traversewith gypsum fibre insert
CW stud
Crimp the traverse to the CW studusing a stud crimper
Traverse dimension 620
Stud spacing 625 (grid dimension)
290
Drilling screwLB 35 x 16
Steel anchoringtraverse with gypsum
fibre insert
UA profile Crimped Steel anchoring traversewith gypsum fibre insert
CW stud
eg Handrail
UA profileKnauf boards
Steel anchoring traversewith gypsum fibre insert
eg Handrail
CW studKnauf board
Steel anchoring traversewith gypsum fibre insert
Loads on partitions and furringsAnchoring in the traverses
Note No web cutouts in the CW studs are permissible for traverses to which the CW studs are attached
14
Loads on partitions and furringsAnchoring in the traverses
Knauf steel anchoring traverseThe steel anchoring traverse is suitable for accepting loads attached to the wall up to 10 kNm wall length eg towel holders cupboards shelves and similar Not suitable for dynamic loads such as folding wall attached seatsThe steel anchoring traverse consists of 075 mm thick sheet metal and are crimped onto the side using a stud crimper on the CW studs Particularly suitable for single-layer clad metal stud partitions and furrings where in case of cantilever loads gt 04 kNm (400 kgm) wall length the installation of a traverse is required
NoteTraverses for installation in damp and wet rooms see also system data sheet W38de Knauf Metal Stud Partitions AQUAPANELreg
Installation and applicationCrimp the steel anchoring traverse made of galvanized sheet steel to the CW studs using a Stud CrimperAdditional screw fastening of the steel anchoring traverse via screw fastening of the cladding (min 2 to 3 anchoring points) Reduce the screw spacing of the cladding if necessaryArrangement in a rowCW studs
Scale 110 I Dimensions in mmDetailsW234de-A11 View W234de V11 Vertical section
eg W111de
W234de-H11 Horizontal sectioneg W111de
Sheet metal gauge 075 mm
Steel anchoring traverse
CW stud
Crimp the traverse to the CW studusing the stud crimper
290
Traverse dimension 620
Stud spacing 625 (grid dimension)
eg Cabinet
CW stud
Knauf boardSteel anchoring traverse
Steel anchoring traverseCW stud
Crimped
Note No web cutouts in the CW studs are permissible for traverses to which the CW studs are attached
15
Full-length SanistandFloor-to-ceiling Sanistands made of galvanized UA profiles (min UA 75) 2 mm thick are suitable for transferring loads from traverses into the supporting structure or for fixing loads hanging onto walls such as school blackboards up to 15 kNm wall lengthFloor-to-ceiling Sanistands profiles are anchored to the basic floor and ceiling with door frame brackets or connection brackets for UA profiles The upper door frame bracket includes openings for routing cables such as pipe-in-pipe systems or electrical cablesThe loads are connected directly to the flange of the UA profile
W228de-A10 View
le 1000 mm
UW runnercontinuous
Door frameconnection brackettop connection withenclosed dowels
CW studAxial spacing suitedto partition system
UA profileas afloor-to-ceilingSanistand forbearing cantileverloads
UW runnercontinuous
Door frameconnection bracketbottom connectionwith enclosed dowels
Scale 110
Installation and applicationFloor-to-ceiling Sanistands made of UA profiles must be anchored to the basic floor and ceiling with door frame brackets or connection brackets for UA profiles The upper door frame bracket includes openings for routing cables such as pipe-in-pipe systems or electrical cables Fasten objects to UA profiles using threaded rods U washers and M1012 steel nuts or self-tapping screws
Loads on partitions and furringsFull-length Sanistand
Detail
Notes
Web cutouts are not permissible in UA Sanistand subject to cantilever loads point loads or linear distributed loadsMaximum screw load with connections to full height Sanistand (UA profile)Every UA profile flange and anchoring point may not exceed a resulting pull-out load of 150 kN (150 kg)Components similar to cantilevers such as foldable rails should be screwed onto two adjacent UA profilesUse suitable drilling screws eg Ejot Zebra Piasta Hilti S-MD or comparable
16
Loads on partitions and furringsFull-length Sanistand
Scale 110DetailsW116de-V1 Sanistand W116de-H1 SanistandVertical section I Without fire resistance Horizontal section I Without fire resistance
UW runnerUniflott + Trenn-Fix
UW runner
Additional UA profile
Sanistand withconcealed mount cistern
Knauf connectionbracket with enclosedM8 carriage bolts
Knauf conection bracket withenclosed M8 carriage bolt
2x 125 mm DiamantDiamant screw XTB
Additional CW stud
Knauf sealing tape
Board strip installationacc to W11de systemdata sheet
Stud spacing le 625 mm
CW stud profile
Additional CW studBoard strip installation in acc with W11de system data sheet
Knauf connection bracket withenclosed M8 carriage bolts
Additional UA profileSanitand with concealedmount cistern
Notes
Max partition height UA 50 = 300 m UA 75 = see system data sheet W11de Knauf Metal Stud Partition for the wall heights
Minimum cladding ge 18 mm Knauf Boards recommendation 2x 125 mm Knauf Diamant
Web cutouts are not permissible in UA Sanistand subject to cantilever loads point loads or linear distributed loadsObserve the manufacturersrsquo details for lateral UA profiles and cladding Additional UA profiles are required laterally on Sanistand mounts acc to DIN 18340 section 374 Only possible without additional UA profiles if the manufacturer of the Sanistand base or WC Sanistand permits itDeviating specifications of the Sanistand manufacturer must be considered and observed
17
Loads on partitions and furringsFull-length Sanistand
Notes
Max partition height rear W112de UA 50 = 300 m UA 75 = see system data sheet W11de Knauf Metal Stud Partition for the wall heights
Minimum cladding front wall installations ge 18 mm Knauf Boards recommendation 2x 125 mm Knauf Diamant
Web cutouts are not permissible in UA Sanistand subject to cantilever loads point loads or linear distributed loadsObserve the manufacturersrsquo details for lateral UA profiles and cladding Additional UA profiles are required laterally on Sanistand mounts acc to DIN 18340 section 374 Only possible without additional UA profiles if the manufacturer of the Sanistand base or WC Sanistand permits itDeviating specifications of the Sanistand manufacturer must be considered and observed
Scale 110DetailsW626Vde-V1 Without back anchoring W626Vde-H1 Without back anchoring Vertical section Horizontal section
UW runnerUniflott + Trenn-Fix
UW runner
Additional UA profile
Sanistand withconcealed mount cistern
Knauf connection bracket withenclosed M8 carriage bolt
Knauf connection bracket withenclosed M8 carriage bolt
2x 125 mm DiamantDiamant screw XTB
Knauf sealing tape
Sanistand withconcealed mount cisternKnauf connection bracket with
enclosed M8 carriage bolts
Stud spacing le 625 mm
UW runner
Knauf boardsCW stud
Additional UA profile
18
Loads on partitions and furringsFull-length Sanistand
Scale 110DetailsW626Vde-V2 Back anchoring in traverse W626Vde-H2 Back anchoring in traverse Vertical section Horizontal section
Sanistand withconcealed mount cistern
SealantUD profile made of insulation strips
UW runner
UW runner
UA profile
Knauf multi-purpose screw FN
Uniflott + Trenn-Fix
Multi-purpose traverse 555 300 23 mm
Knauf connection bracket withenclosed M8 carriage bolts
2x 125 mm DiamantDiamant screw XTB
Knauf connection bracket withenclosed M8 carriage bolt
Wall anchor installation acc to WCSanistand manufacturer specifications
Knauf sealing tape
Stud spacing le 625 mm
Multi-purpose traverse555 300 23 mm
UA profile
UA profile
Knauf connection bracket withenclosed M8 carriage bolt
Knauf connectionbracket with enclosedM8 carriage bolt
Wall anchorinstallation acc to
WC Sanistandmanufacturerspecifications
Notes
Max partition height rear W112de UA 50 = 300 m UA 75 = see system data sheet W11de Knauf Metal Stud Partitions for the wall heights
Minimum cladding front wall installations ge 18 mm Knauf Boards recommendation 2x 125 mm Knauf Diamant
Web cutouts are not permissible in UA Sanistand subject to cantilever loads point loads or linear distributed loadsObserve the manufacturersrsquo details for lateral UA profiles and cladding Additional UA profiles are required laterally on Sanistand mounts acc to DIN 18340 section 374 Only possible without additional UA profiles if the manufacturer of the Sanistand base or WC Sanistand permits itDeviating specifications of the Sanistand manufacturer must be considered and observed
19
Loads on partitions and furringsFull-length Sanistand
Scale 110DetailsW626Vde-V3 Back anchoring in UA profile W626Vde-H3 Back anchoring in UA profile Vertical section Horizontal section
Sanistand withconcealed mount cistern
SealantUD profile on insulation strips
UW runner
UW runner
Additional UA profile
Knauf multi-purpose screw FN
Uniflott + Trenn-Fix
UA profile
Knauf connection bracket withenclosed M8 carriage bolts
2x 125 mm DiamantDiamant screw XTB
Knauf connection bracket withenclosed M8 carriage bolts
Fixing bolts with nuts andwashers
Knauf sealing tape
Stud spacing le 625 mm
Additional UA profile
UA profile Fixing bolts with nutsand washers
Knauf connection bracket withenclosed M8 carriage bolts
Knauf connectionbracket with enclosedM8 carriage bolts
Notes
Max partition height at rear W112de UA 50 = 300 m UA 75 = see system data sheet W11de Knauf Metal Stud Partition for the wall heights
Minimum cladding front wall installations ge 18 mm Knauf Boards recommendation 2x 125 mm Knauf Diamant
Web cutouts are not permissible in UA Sanistand subject to cantilever loads point loads or linear distributed loadsObserve the manufacturersrsquo details for lateral UA profiles and cladding Additional UA profiles are required laterally on Sanistand mounts acc to DIN 18340 section 374 Only possible without additional UA profiles if the manufacturer of the Sanistand base or WC Sanistand permits itDeviating specifications of the Sanistand manufacturer must be considered and observed
20
Loads on partitions and furringsFull-length Sanistand
Scale 110DetailsW626Vde-V4 Back anchoring in mounting rail W626Vde-H4 Back anchoring in mounting rail Vertical section Horizontal section
Sanistand withconcealed mount cistern
2x 125 mm Diamant
SealantUD profile on insulation strips
UW runner
Diamant screw XTB
UA profile
Knauf multi-purpose screw FN
Mounting rail with fixing screw
Knauf connection bracket withenclosed M8 carriage bolt
Uniflott + Trenn-Fix
UA profile
Knauf connection bracket withenclosed M8 carriage bolt
Knauf sealing tapeUW runner
Stud spacing le 625 mm
UA profile
UA profile
Mounting railFixing screw
Mounting screw
Sanistand withconcealed mount cistern
Knauf connection bracket withenclosed M8 carriage bolt
Knauf connectionbracket with enclosedM8 carriage bolt
Notes
Max partition height rear W112de UA 50 = 300 m UA 75 = see system data sheet W11de Knauf Metal Stud Partitions for the wall heights
Minimum cladding front wall installations ge 18 mm Knauf Boards recommendation 2x 125 mm Knauf Diamant
Web cutouts are not permissible in UA Sanistand subject to cantilever loads point loads or linear distributed loadsObserve the manufacturersrsquo details for lateral UA profiles and cladding Additional UA profiles are required laterally on Sanistand mounts acc to DIN 18340 section 374 Only possible without additional UA profiles if the manufacturer of the Sanistand base or WC Sanistand permits itDeviating specifications of the Sanistand manufacturer must be considered and observed
21
Notes
In case of load attachment to ldquomulti-level ceiling systemsrdquo refer to the respective valid Knauf system data sheetsIn case of attachment of loads to free-spanning ceilings see system data sheet D13de Knauf Free-Spanning Ceilings
Attachment of loads to Knauf board ceilingsAdditional loads eg lighting fixtures curtain rails and similar can be fixed to Knauf board ceilings using universal dowels cavity dowels spring toggle dowels or Knauf Hartmut Hohlraumduumlbel cavity dowelsAdditional loads must be considered when determining the load class
NoteHeavy loads must be attached directly on load-bearing building elements (basic ceiling) or on auxiliary constructions eg traverses
For each area under load of the Knauf board ceiling the weight of thefastened components may not exceed the following limits
Permissible weight per ceiling area in kgmsup2Without fire resistance With fire resistance1)
15 61)Incaseofapplicationasafireresistanceceilingwithexposedceiling(multi-levelceilingsystem)15kgmsup2totalweightispermissiblefortheexposedceiling(includinginsulationlayerandattachedloads)attachedtothefireresistanceceiling
Furthermore the following conditions applyFor each anchoring point the components fastened to the board ceiling may not exceed the following weights
Fastening method Permissible weight per anchoring point in kgWithout fire resistance With fire resistance
Fastening in the cladding 6 05
Fastening to the grid 10 10
Fastening in the claddingKnauf Hartmut Hohlraumduumlbel cavity dowelScrew M5
Fastening to the gridKnauf Universalschraube FN multi-purpose screw eg curtain rail
The minimum separation spacings between individual attached loads must be observed to avoid local overloading of the ceiling The minimum separation clearance between two attachment points consists of both load radii for the point loadsThe load radius of a point load can be taken from the following diagram in dependence on the permissible weight per unit area for additional loads
Point load in kg
7570656055504540353025201510
0 2 3 4 5 6 7 8 9 10
Radiu
s in c
m
1
50
Fastening in the claddingpossible (without fire resistance)
3 kgmsup2 permissible additional weight (on the exposed ceiling under a fire resistance ceiling refer to the respective valid Knauf system data sheets)6 kgmsup2 permissible additional weight (with fire resistance)15 kgmsup2 permissible additional weight (without fire resistance)
Example fastening scheme at 15 kgmsup2
05 kg
10 kg
3 kgr = 25 cm
r = 46 cm
6 kgr = 355 cm
1 kg
r = 15 cm
r = 105 cm
NoteThe anchored loads can be transferred using several anchoring elements
Loads on board ceilingsFastening in the cladding grid
22
Knauf multi-purpose traversesThe multi-purpose traverse in Knauf board ceilings is suitable for the application of point loads up to 075 kN eg chandeliers music speakers or similarThe multi-purpose traverse consists of a 23 mm thick multi-layer wooden board and galvanized sheet metal profiles It is fastened to the side of the CD furring channelThe attachment of the loads to the traverses should be performed using Knauf Multi-Purpose Screw FNInstallation is possible in a double layer profile grid and flush profile grid
Installation and applicationBend the Daisy chain clip before lateral screw fastening The Daisy chain clip is then Z shaped The unpunched metal side of the Daisy chain clip is pushed onto the lower side of the traverse and then screw fastened laterally through the factory-made hole on the long side of the traverse Screw fasten 4x Daisy chain clips each using one drywall screw TN 35 x 35 about 100 mm from the corner of the multi-layer board on the long edge of the multi-purpose traverse Arrange an additional CD channel (length ge 650 mm) for every long edge in accordance with the width of the multi-purpose traverse Alternately a ceiling furring channel can be used for application of the multi-purpose traverse The supporting profiles are suspended using ceiling suspenders of load class 40 kg The suspenders may not be situated in the direct vicinity of the longitudinal area of the traverse as this will hinder the installation of the traverse Introduce the multi-purpose traverse between the support profiles bend the Daisy chain clip around the CD channel and engage it In case of single-layer cladding do not screw fasten the surface cladding with the multi-purpose traverse
1 Apply the Daisy chain clip 2 Bend the Daisy chain clip 3 Screw fasten the Daisy chain clip
Loads on board ceilingsAnchoring in the traverses
100 mm
23
Loads on board ceilingsAnchoring in the traverses
Scale 110 I Dimensions in mmDetailsD112de SO18 Vertical section ndash Multi-purpose traverse D113de SO12 Vertical section ndash Multi-purpose traverseeg with two additional CD channels I Without fire resistance eg with one additional CD channel I Without fire resistance
D112de SO19 Vertical section ndash Multi-purpose traverse D113de SO13 Vertical section ndash Multi-purpose traverseeg with two additional CD channels I Without fire resistance eg with one additional CD channel I Without fire resistance
D112de SO20 Top view ndash Multi-purpose traverse D113de SO14 Top view ndash Multi-purpose traverseeg with two additional CD channels I Without fire resistance eg with one additional CD channel I Without fire resistance
Fasten Daisy chain clip with drywall screwTN 35 x 35 to multi-purpose traverse
Additional CD channel with two suspendersLoad bearing capacity class ge 040 kN
Multi-purposetraverse555 300 23 mm
300
Furring channel spacing 500
Fasten Daisy chain clip with drywall screwTN 35 x 35 to multi-purpose traverse
Additional suspended load bearing capacity class ge 040 kNMulti-purposetraverse555 300 23 mm
300
Furring channel spacing 500
Additional CD channel with two suspendersLoad bearing capacity class ge 040 kN
Multi-purposetraverse555 300 23 mm
Fasten Daisy chain clip with drywall screwTN 35 x 35 to multi-purpose traverse
Wood panel 555approx
100
Additional suspenderload bearing capacityclass ge 040 kN
Multi-purposetraverse555 300 23 mm
Fasten Daisy chain clip with drywall screwTN 35 x 35 to multi-purpose traverse
Wood panel 555approx
100
Daisy chain clip
Furring channel spacing 500
Traverse
CDchannel
Multi-layerwood panel
Furring channel spacing 500
Multi-purposetraverse
Daisy chain clip
Multi-layerwood panel
Additional grid 4 additional suspension points (eg Nonius suspension)
All technical changes reserved Only the current printed instructions are valid The stated information represents current state-of-the-art Knauf technology The entire state of approved engineering rules appropriate standards guidelines and rules of crafts-manship are not included herewith These and all application instructions have to be adhered to separately by the installer Our warranty is expressly limited to our products in flawless condition All application quantities and delivery amounts are based on empirical data that are not easily transferable to other deviating areasAll rights reserved All amendments reprints and photocopies including those of excerpts require our expressed permission
The stated constructional and structural design specifications and characteristics of building physics of Knauf systems can only be ensured with the exclusive use of Knauf system components or other products expressly recommended by Knauf
Knauf Gips KG Am Bahnhof 7 97346 Iphofen GermanyKnauf DirectTechnical Advisory Service
knauf-direktknaufde
wwwknaufde
VT03deeng09190TI
The iPad App Knauf Infothek now provides all the current information and documents from Knauf Gips KG at any time and in every location in a clear and comfortable wayKnauf Infothek
Videos for Knauf systems and products can be found under the following linkwwwyoutubecomknaufEPD
12
Knauf steel anchoring traverse with gypsum fibre insertThe steel anchoring traverse with gypsum fibre insert is suitable for accepting loads attached to the wall up to 15 kNm wall length eg cupboards shelves handrails and similarThe metal traverse with gypsum fibre insert consists of 075 mm thick sheet metal as well as an 18 mm thick gypsum fibre board It is fastened to the side of the floor-to-ceiling profiles The attachment of the loads to the traverses should be performed using Knauf Multi-Purpose Screw FNUse in partition systems where the requirement for non-combustible reaction to fire exists
Installation and applicationSteel anchoring traverse made of galvanized steel with gypsum fibre insert fastened to the CW studs UA profiles In case of CW studs crimp using a Stud Crimper and for UA profiles screw fasten with 6 Drilling screws LB 35 x 16 mmArrangement in a rowUA profiles CW studs
Loads on partitions and furringsAnchoring in the traverses
13
Scale 110 I Dimensions in mmDetailsW234de-A12 View - Design with UA profile W234de-A14 View - Design with CW stud
W234de-H12 Horizontal section - Design with UA profile W234de-H14 Horizontal section - Design with CW studeg W112de eg W112de
W234de-V12 Vertical section - Design with UA profile W234de-V14 Vertical section - Design with CW studeg W112de eg W112de
Traverse dimension 620
Stud spacing 625 (grid dimension)
290
Steel anchoring traversewith gypsum fibre insert
Traverse attached to UA profileusing drilling screws
UA profile
Steel anchoring traversewith gypsum fibre insert
CW stud
Crimp the traverse to the CW studusing a stud crimper
Traverse dimension 620
Stud spacing 625 (grid dimension)
290
Drilling screwLB 35 x 16
Steel anchoringtraverse with gypsum
fibre insert
UA profile Crimped Steel anchoring traversewith gypsum fibre insert
CW stud
eg Handrail
UA profileKnauf boards
Steel anchoring traversewith gypsum fibre insert
eg Handrail
CW studKnauf board
Steel anchoring traversewith gypsum fibre insert
Loads on partitions and furringsAnchoring in the traverses
Note No web cutouts in the CW studs are permissible for traverses to which the CW studs are attached
14
Loads on partitions and furringsAnchoring in the traverses
Knauf steel anchoring traverseThe steel anchoring traverse is suitable for accepting loads attached to the wall up to 10 kNm wall length eg towel holders cupboards shelves and similar Not suitable for dynamic loads such as folding wall attached seatsThe steel anchoring traverse consists of 075 mm thick sheet metal and are crimped onto the side using a stud crimper on the CW studs Particularly suitable for single-layer clad metal stud partitions and furrings where in case of cantilever loads gt 04 kNm (400 kgm) wall length the installation of a traverse is required
NoteTraverses for installation in damp and wet rooms see also system data sheet W38de Knauf Metal Stud Partitions AQUAPANELreg
Installation and applicationCrimp the steel anchoring traverse made of galvanized sheet steel to the CW studs using a Stud CrimperAdditional screw fastening of the steel anchoring traverse via screw fastening of the cladding (min 2 to 3 anchoring points) Reduce the screw spacing of the cladding if necessaryArrangement in a rowCW studs
Scale 110 I Dimensions in mmDetailsW234de-A11 View W234de V11 Vertical section
eg W111de
W234de-H11 Horizontal sectioneg W111de
Sheet metal gauge 075 mm
Steel anchoring traverse
CW stud
Crimp the traverse to the CW studusing the stud crimper
290
Traverse dimension 620
Stud spacing 625 (grid dimension)
eg Cabinet
CW stud
Knauf boardSteel anchoring traverse
Steel anchoring traverseCW stud
Crimped
Note No web cutouts in the CW studs are permissible for traverses to which the CW studs are attached
15
Full-length SanistandFloor-to-ceiling Sanistands made of galvanized UA profiles (min UA 75) 2 mm thick are suitable for transferring loads from traverses into the supporting structure or for fixing loads hanging onto walls such as school blackboards up to 15 kNm wall lengthFloor-to-ceiling Sanistands profiles are anchored to the basic floor and ceiling with door frame brackets or connection brackets for UA profiles The upper door frame bracket includes openings for routing cables such as pipe-in-pipe systems or electrical cablesThe loads are connected directly to the flange of the UA profile
W228de-A10 View
le 1000 mm
UW runnercontinuous
Door frameconnection brackettop connection withenclosed dowels
CW studAxial spacing suitedto partition system
UA profileas afloor-to-ceilingSanistand forbearing cantileverloads
UW runnercontinuous
Door frameconnection bracketbottom connectionwith enclosed dowels
Scale 110
Installation and applicationFloor-to-ceiling Sanistands made of UA profiles must be anchored to the basic floor and ceiling with door frame brackets or connection brackets for UA profiles The upper door frame bracket includes openings for routing cables such as pipe-in-pipe systems or electrical cables Fasten objects to UA profiles using threaded rods U washers and M1012 steel nuts or self-tapping screws
Loads on partitions and furringsFull-length Sanistand
Detail
Notes
Web cutouts are not permissible in UA Sanistand subject to cantilever loads point loads or linear distributed loadsMaximum screw load with connections to full height Sanistand (UA profile)Every UA profile flange and anchoring point may not exceed a resulting pull-out load of 150 kN (150 kg)Components similar to cantilevers such as foldable rails should be screwed onto two adjacent UA profilesUse suitable drilling screws eg Ejot Zebra Piasta Hilti S-MD or comparable
16
Loads on partitions and furringsFull-length Sanistand
Scale 110DetailsW116de-V1 Sanistand W116de-H1 SanistandVertical section I Without fire resistance Horizontal section I Without fire resistance
UW runnerUniflott + Trenn-Fix
UW runner
Additional UA profile
Sanistand withconcealed mount cistern
Knauf connectionbracket with enclosedM8 carriage bolts
Knauf conection bracket withenclosed M8 carriage bolt
2x 125 mm DiamantDiamant screw XTB
Additional CW stud
Knauf sealing tape
Board strip installationacc to W11de systemdata sheet
Stud spacing le 625 mm
CW stud profile
Additional CW studBoard strip installation in acc with W11de system data sheet
Knauf connection bracket withenclosed M8 carriage bolts
Additional UA profileSanitand with concealedmount cistern
Notes
Max partition height UA 50 = 300 m UA 75 = see system data sheet W11de Knauf Metal Stud Partition for the wall heights
Minimum cladding ge 18 mm Knauf Boards recommendation 2x 125 mm Knauf Diamant
Web cutouts are not permissible in UA Sanistand subject to cantilever loads point loads or linear distributed loadsObserve the manufacturersrsquo details for lateral UA profiles and cladding Additional UA profiles are required laterally on Sanistand mounts acc to DIN 18340 section 374 Only possible without additional UA profiles if the manufacturer of the Sanistand base or WC Sanistand permits itDeviating specifications of the Sanistand manufacturer must be considered and observed
17
Loads on partitions and furringsFull-length Sanistand
Notes
Max partition height rear W112de UA 50 = 300 m UA 75 = see system data sheet W11de Knauf Metal Stud Partition for the wall heights
Minimum cladding front wall installations ge 18 mm Knauf Boards recommendation 2x 125 mm Knauf Diamant
Web cutouts are not permissible in UA Sanistand subject to cantilever loads point loads or linear distributed loadsObserve the manufacturersrsquo details for lateral UA profiles and cladding Additional UA profiles are required laterally on Sanistand mounts acc to DIN 18340 section 374 Only possible without additional UA profiles if the manufacturer of the Sanistand base or WC Sanistand permits itDeviating specifications of the Sanistand manufacturer must be considered and observed
Scale 110DetailsW626Vde-V1 Without back anchoring W626Vde-H1 Without back anchoring Vertical section Horizontal section
UW runnerUniflott + Trenn-Fix
UW runner
Additional UA profile
Sanistand withconcealed mount cistern
Knauf connection bracket withenclosed M8 carriage bolt
Knauf connection bracket withenclosed M8 carriage bolt
2x 125 mm DiamantDiamant screw XTB
Knauf sealing tape
Sanistand withconcealed mount cisternKnauf connection bracket with
enclosed M8 carriage bolts
Stud spacing le 625 mm
UW runner
Knauf boardsCW stud
Additional UA profile
18
Loads on partitions and furringsFull-length Sanistand
Scale 110DetailsW626Vde-V2 Back anchoring in traverse W626Vde-H2 Back anchoring in traverse Vertical section Horizontal section
Sanistand withconcealed mount cistern
SealantUD profile made of insulation strips
UW runner
UW runner
UA profile
Knauf multi-purpose screw FN
Uniflott + Trenn-Fix
Multi-purpose traverse 555 300 23 mm
Knauf connection bracket withenclosed M8 carriage bolts
2x 125 mm DiamantDiamant screw XTB
Knauf connection bracket withenclosed M8 carriage bolt
Wall anchor installation acc to WCSanistand manufacturer specifications
Knauf sealing tape
Stud spacing le 625 mm
Multi-purpose traverse555 300 23 mm
UA profile
UA profile
Knauf connection bracket withenclosed M8 carriage bolt
Knauf connectionbracket with enclosedM8 carriage bolt
Wall anchorinstallation acc to
WC Sanistandmanufacturerspecifications
Notes
Max partition height rear W112de UA 50 = 300 m UA 75 = see system data sheet W11de Knauf Metal Stud Partitions for the wall heights
Minimum cladding front wall installations ge 18 mm Knauf Boards recommendation 2x 125 mm Knauf Diamant
Web cutouts are not permissible in UA Sanistand subject to cantilever loads point loads or linear distributed loadsObserve the manufacturersrsquo details for lateral UA profiles and cladding Additional UA profiles are required laterally on Sanistand mounts acc to DIN 18340 section 374 Only possible without additional UA profiles if the manufacturer of the Sanistand base or WC Sanistand permits itDeviating specifications of the Sanistand manufacturer must be considered and observed
19
Loads on partitions and furringsFull-length Sanistand
Scale 110DetailsW626Vde-V3 Back anchoring in UA profile W626Vde-H3 Back anchoring in UA profile Vertical section Horizontal section
Sanistand withconcealed mount cistern
SealantUD profile on insulation strips
UW runner
UW runner
Additional UA profile
Knauf multi-purpose screw FN
Uniflott + Trenn-Fix
UA profile
Knauf connection bracket withenclosed M8 carriage bolts
2x 125 mm DiamantDiamant screw XTB
Knauf connection bracket withenclosed M8 carriage bolts
Fixing bolts with nuts andwashers
Knauf sealing tape
Stud spacing le 625 mm
Additional UA profile
UA profile Fixing bolts with nutsand washers
Knauf connection bracket withenclosed M8 carriage bolts
Knauf connectionbracket with enclosedM8 carriage bolts
Notes
Max partition height at rear W112de UA 50 = 300 m UA 75 = see system data sheet W11de Knauf Metal Stud Partition for the wall heights
Minimum cladding front wall installations ge 18 mm Knauf Boards recommendation 2x 125 mm Knauf Diamant
Web cutouts are not permissible in UA Sanistand subject to cantilever loads point loads or linear distributed loadsObserve the manufacturersrsquo details for lateral UA profiles and cladding Additional UA profiles are required laterally on Sanistand mounts acc to DIN 18340 section 374 Only possible without additional UA profiles if the manufacturer of the Sanistand base or WC Sanistand permits itDeviating specifications of the Sanistand manufacturer must be considered and observed
20
Loads on partitions and furringsFull-length Sanistand
Scale 110DetailsW626Vde-V4 Back anchoring in mounting rail W626Vde-H4 Back anchoring in mounting rail Vertical section Horizontal section
Sanistand withconcealed mount cistern
2x 125 mm Diamant
SealantUD profile on insulation strips
UW runner
Diamant screw XTB
UA profile
Knauf multi-purpose screw FN
Mounting rail with fixing screw
Knauf connection bracket withenclosed M8 carriage bolt
Uniflott + Trenn-Fix
UA profile
Knauf connection bracket withenclosed M8 carriage bolt
Knauf sealing tapeUW runner
Stud spacing le 625 mm
UA profile
UA profile
Mounting railFixing screw
Mounting screw
Sanistand withconcealed mount cistern
Knauf connection bracket withenclosed M8 carriage bolt
Knauf connectionbracket with enclosedM8 carriage bolt
Notes
Max partition height rear W112de UA 50 = 300 m UA 75 = see system data sheet W11de Knauf Metal Stud Partitions for the wall heights
Minimum cladding front wall installations ge 18 mm Knauf Boards recommendation 2x 125 mm Knauf Diamant
Web cutouts are not permissible in UA Sanistand subject to cantilever loads point loads or linear distributed loadsObserve the manufacturersrsquo details for lateral UA profiles and cladding Additional UA profiles are required laterally on Sanistand mounts acc to DIN 18340 section 374 Only possible without additional UA profiles if the manufacturer of the Sanistand base or WC Sanistand permits itDeviating specifications of the Sanistand manufacturer must be considered and observed
21
Notes
In case of load attachment to ldquomulti-level ceiling systemsrdquo refer to the respective valid Knauf system data sheetsIn case of attachment of loads to free-spanning ceilings see system data sheet D13de Knauf Free-Spanning Ceilings
Attachment of loads to Knauf board ceilingsAdditional loads eg lighting fixtures curtain rails and similar can be fixed to Knauf board ceilings using universal dowels cavity dowels spring toggle dowels or Knauf Hartmut Hohlraumduumlbel cavity dowelsAdditional loads must be considered when determining the load class
NoteHeavy loads must be attached directly on load-bearing building elements (basic ceiling) or on auxiliary constructions eg traverses
For each area under load of the Knauf board ceiling the weight of thefastened components may not exceed the following limits
Permissible weight per ceiling area in kgmsup2Without fire resistance With fire resistance1)
15 61)Incaseofapplicationasafireresistanceceilingwithexposedceiling(multi-levelceilingsystem)15kgmsup2totalweightispermissiblefortheexposedceiling(includinginsulationlayerandattachedloads)attachedtothefireresistanceceiling
Furthermore the following conditions applyFor each anchoring point the components fastened to the board ceiling may not exceed the following weights
Fastening method Permissible weight per anchoring point in kgWithout fire resistance With fire resistance
Fastening in the cladding 6 05
Fastening to the grid 10 10
Fastening in the claddingKnauf Hartmut Hohlraumduumlbel cavity dowelScrew M5
Fastening to the gridKnauf Universalschraube FN multi-purpose screw eg curtain rail
The minimum separation spacings between individual attached loads must be observed to avoid local overloading of the ceiling The minimum separation clearance between two attachment points consists of both load radii for the point loadsThe load radius of a point load can be taken from the following diagram in dependence on the permissible weight per unit area for additional loads
Point load in kg
7570656055504540353025201510
0 2 3 4 5 6 7 8 9 10
Radiu
s in c
m
1
50
Fastening in the claddingpossible (without fire resistance)
3 kgmsup2 permissible additional weight (on the exposed ceiling under a fire resistance ceiling refer to the respective valid Knauf system data sheets)6 kgmsup2 permissible additional weight (with fire resistance)15 kgmsup2 permissible additional weight (without fire resistance)
Example fastening scheme at 15 kgmsup2
05 kg
10 kg
3 kgr = 25 cm
r = 46 cm
6 kgr = 355 cm
1 kg
r = 15 cm
r = 105 cm
NoteThe anchored loads can be transferred using several anchoring elements
Loads on board ceilingsFastening in the cladding grid
22
Knauf multi-purpose traversesThe multi-purpose traverse in Knauf board ceilings is suitable for the application of point loads up to 075 kN eg chandeliers music speakers or similarThe multi-purpose traverse consists of a 23 mm thick multi-layer wooden board and galvanized sheet metal profiles It is fastened to the side of the CD furring channelThe attachment of the loads to the traverses should be performed using Knauf Multi-Purpose Screw FNInstallation is possible in a double layer profile grid and flush profile grid
Installation and applicationBend the Daisy chain clip before lateral screw fastening The Daisy chain clip is then Z shaped The unpunched metal side of the Daisy chain clip is pushed onto the lower side of the traverse and then screw fastened laterally through the factory-made hole on the long side of the traverse Screw fasten 4x Daisy chain clips each using one drywall screw TN 35 x 35 about 100 mm from the corner of the multi-layer board on the long edge of the multi-purpose traverse Arrange an additional CD channel (length ge 650 mm) for every long edge in accordance with the width of the multi-purpose traverse Alternately a ceiling furring channel can be used for application of the multi-purpose traverse The supporting profiles are suspended using ceiling suspenders of load class 40 kg The suspenders may not be situated in the direct vicinity of the longitudinal area of the traverse as this will hinder the installation of the traverse Introduce the multi-purpose traverse between the support profiles bend the Daisy chain clip around the CD channel and engage it In case of single-layer cladding do not screw fasten the surface cladding with the multi-purpose traverse
1 Apply the Daisy chain clip 2 Bend the Daisy chain clip 3 Screw fasten the Daisy chain clip
Loads on board ceilingsAnchoring in the traverses
100 mm
23
Loads on board ceilingsAnchoring in the traverses
Scale 110 I Dimensions in mmDetailsD112de SO18 Vertical section ndash Multi-purpose traverse D113de SO12 Vertical section ndash Multi-purpose traverseeg with two additional CD channels I Without fire resistance eg with one additional CD channel I Without fire resistance
D112de SO19 Vertical section ndash Multi-purpose traverse D113de SO13 Vertical section ndash Multi-purpose traverseeg with two additional CD channels I Without fire resistance eg with one additional CD channel I Without fire resistance
D112de SO20 Top view ndash Multi-purpose traverse D113de SO14 Top view ndash Multi-purpose traverseeg with two additional CD channels I Without fire resistance eg with one additional CD channel I Without fire resistance
Fasten Daisy chain clip with drywall screwTN 35 x 35 to multi-purpose traverse
Additional CD channel with two suspendersLoad bearing capacity class ge 040 kN
Multi-purposetraverse555 300 23 mm
300
Furring channel spacing 500
Fasten Daisy chain clip with drywall screwTN 35 x 35 to multi-purpose traverse
Additional suspended load bearing capacity class ge 040 kNMulti-purposetraverse555 300 23 mm
300
Furring channel spacing 500
Additional CD channel with two suspendersLoad bearing capacity class ge 040 kN
Multi-purposetraverse555 300 23 mm
Fasten Daisy chain clip with drywall screwTN 35 x 35 to multi-purpose traverse
Wood panel 555approx
100
Additional suspenderload bearing capacityclass ge 040 kN
Multi-purposetraverse555 300 23 mm
Fasten Daisy chain clip with drywall screwTN 35 x 35 to multi-purpose traverse
Wood panel 555approx
100
Daisy chain clip
Furring channel spacing 500
Traverse
CDchannel
Multi-layerwood panel
Furring channel spacing 500
Multi-purposetraverse
Daisy chain clip
Multi-layerwood panel
Additional grid 4 additional suspension points (eg Nonius suspension)
All technical changes reserved Only the current printed instructions are valid The stated information represents current state-of-the-art Knauf technology The entire state of approved engineering rules appropriate standards guidelines and rules of crafts-manship are not included herewith These and all application instructions have to be adhered to separately by the installer Our warranty is expressly limited to our products in flawless condition All application quantities and delivery amounts are based on empirical data that are not easily transferable to other deviating areasAll rights reserved All amendments reprints and photocopies including those of excerpts require our expressed permission
The stated constructional and structural design specifications and characteristics of building physics of Knauf systems can only be ensured with the exclusive use of Knauf system components or other products expressly recommended by Knauf
Knauf Gips KG Am Bahnhof 7 97346 Iphofen GermanyKnauf DirectTechnical Advisory Service
knauf-direktknaufde
wwwknaufde
VT03deeng09190TI
The iPad App Knauf Infothek now provides all the current information and documents from Knauf Gips KG at any time and in every location in a clear and comfortable wayKnauf Infothek
Videos for Knauf systems and products can be found under the following linkwwwyoutubecomknaufEPD
13
Scale 110 I Dimensions in mmDetailsW234de-A12 View - Design with UA profile W234de-A14 View - Design with CW stud
W234de-H12 Horizontal section - Design with UA profile W234de-H14 Horizontal section - Design with CW studeg W112de eg W112de
W234de-V12 Vertical section - Design with UA profile W234de-V14 Vertical section - Design with CW studeg W112de eg W112de
Traverse dimension 620
Stud spacing 625 (grid dimension)
290
Steel anchoring traversewith gypsum fibre insert
Traverse attached to UA profileusing drilling screws
UA profile
Steel anchoring traversewith gypsum fibre insert
CW stud
Crimp the traverse to the CW studusing a stud crimper
Traverse dimension 620
Stud spacing 625 (grid dimension)
290
Drilling screwLB 35 x 16
Steel anchoringtraverse with gypsum
fibre insert
UA profile Crimped Steel anchoring traversewith gypsum fibre insert
CW stud
eg Handrail
UA profileKnauf boards
Steel anchoring traversewith gypsum fibre insert
eg Handrail
CW studKnauf board
Steel anchoring traversewith gypsum fibre insert
Loads on partitions and furringsAnchoring in the traverses
Note No web cutouts in the CW studs are permissible for traverses to which the CW studs are attached
14
Loads on partitions and furringsAnchoring in the traverses
Knauf steel anchoring traverseThe steel anchoring traverse is suitable for accepting loads attached to the wall up to 10 kNm wall length eg towel holders cupboards shelves and similar Not suitable for dynamic loads such as folding wall attached seatsThe steel anchoring traverse consists of 075 mm thick sheet metal and are crimped onto the side using a stud crimper on the CW studs Particularly suitable for single-layer clad metal stud partitions and furrings where in case of cantilever loads gt 04 kNm (400 kgm) wall length the installation of a traverse is required
NoteTraverses for installation in damp and wet rooms see also system data sheet W38de Knauf Metal Stud Partitions AQUAPANELreg
Installation and applicationCrimp the steel anchoring traverse made of galvanized sheet steel to the CW studs using a Stud CrimperAdditional screw fastening of the steel anchoring traverse via screw fastening of the cladding (min 2 to 3 anchoring points) Reduce the screw spacing of the cladding if necessaryArrangement in a rowCW studs
Scale 110 I Dimensions in mmDetailsW234de-A11 View W234de V11 Vertical section
eg W111de
W234de-H11 Horizontal sectioneg W111de
Sheet metal gauge 075 mm
Steel anchoring traverse
CW stud
Crimp the traverse to the CW studusing the stud crimper
290
Traverse dimension 620
Stud spacing 625 (grid dimension)
eg Cabinet
CW stud
Knauf boardSteel anchoring traverse
Steel anchoring traverseCW stud
Crimped
Note No web cutouts in the CW studs are permissible for traverses to which the CW studs are attached
15
Full-length SanistandFloor-to-ceiling Sanistands made of galvanized UA profiles (min UA 75) 2 mm thick are suitable for transferring loads from traverses into the supporting structure or for fixing loads hanging onto walls such as school blackboards up to 15 kNm wall lengthFloor-to-ceiling Sanistands profiles are anchored to the basic floor and ceiling with door frame brackets or connection brackets for UA profiles The upper door frame bracket includes openings for routing cables such as pipe-in-pipe systems or electrical cablesThe loads are connected directly to the flange of the UA profile
W228de-A10 View
le 1000 mm
UW runnercontinuous
Door frameconnection brackettop connection withenclosed dowels
CW studAxial spacing suitedto partition system
UA profileas afloor-to-ceilingSanistand forbearing cantileverloads
UW runnercontinuous
Door frameconnection bracketbottom connectionwith enclosed dowels
Scale 110
Installation and applicationFloor-to-ceiling Sanistands made of UA profiles must be anchored to the basic floor and ceiling with door frame brackets or connection brackets for UA profiles The upper door frame bracket includes openings for routing cables such as pipe-in-pipe systems or electrical cables Fasten objects to UA profiles using threaded rods U washers and M1012 steel nuts or self-tapping screws
Loads on partitions and furringsFull-length Sanistand
Detail
Notes
Web cutouts are not permissible in UA Sanistand subject to cantilever loads point loads or linear distributed loadsMaximum screw load with connections to full height Sanistand (UA profile)Every UA profile flange and anchoring point may not exceed a resulting pull-out load of 150 kN (150 kg)Components similar to cantilevers such as foldable rails should be screwed onto two adjacent UA profilesUse suitable drilling screws eg Ejot Zebra Piasta Hilti S-MD or comparable
16
Loads on partitions and furringsFull-length Sanistand
Scale 110DetailsW116de-V1 Sanistand W116de-H1 SanistandVertical section I Without fire resistance Horizontal section I Without fire resistance
UW runnerUniflott + Trenn-Fix
UW runner
Additional UA profile
Sanistand withconcealed mount cistern
Knauf connectionbracket with enclosedM8 carriage bolts
Knauf conection bracket withenclosed M8 carriage bolt
2x 125 mm DiamantDiamant screw XTB
Additional CW stud
Knauf sealing tape
Board strip installationacc to W11de systemdata sheet
Stud spacing le 625 mm
CW stud profile
Additional CW studBoard strip installation in acc with W11de system data sheet
Knauf connection bracket withenclosed M8 carriage bolts
Additional UA profileSanitand with concealedmount cistern
Notes
Max partition height UA 50 = 300 m UA 75 = see system data sheet W11de Knauf Metal Stud Partition for the wall heights
Minimum cladding ge 18 mm Knauf Boards recommendation 2x 125 mm Knauf Diamant
Web cutouts are not permissible in UA Sanistand subject to cantilever loads point loads or linear distributed loadsObserve the manufacturersrsquo details for lateral UA profiles and cladding Additional UA profiles are required laterally on Sanistand mounts acc to DIN 18340 section 374 Only possible without additional UA profiles if the manufacturer of the Sanistand base or WC Sanistand permits itDeviating specifications of the Sanistand manufacturer must be considered and observed
17
Loads on partitions and furringsFull-length Sanistand
Notes
Max partition height rear W112de UA 50 = 300 m UA 75 = see system data sheet W11de Knauf Metal Stud Partition for the wall heights
Minimum cladding front wall installations ge 18 mm Knauf Boards recommendation 2x 125 mm Knauf Diamant
Web cutouts are not permissible in UA Sanistand subject to cantilever loads point loads or linear distributed loadsObserve the manufacturersrsquo details for lateral UA profiles and cladding Additional UA profiles are required laterally on Sanistand mounts acc to DIN 18340 section 374 Only possible without additional UA profiles if the manufacturer of the Sanistand base or WC Sanistand permits itDeviating specifications of the Sanistand manufacturer must be considered and observed
Scale 110DetailsW626Vde-V1 Without back anchoring W626Vde-H1 Without back anchoring Vertical section Horizontal section
UW runnerUniflott + Trenn-Fix
UW runner
Additional UA profile
Sanistand withconcealed mount cistern
Knauf connection bracket withenclosed M8 carriage bolt
Knauf connection bracket withenclosed M8 carriage bolt
2x 125 mm DiamantDiamant screw XTB
Knauf sealing tape
Sanistand withconcealed mount cisternKnauf connection bracket with
enclosed M8 carriage bolts
Stud spacing le 625 mm
UW runner
Knauf boardsCW stud
Additional UA profile
18
Loads on partitions and furringsFull-length Sanistand
Scale 110DetailsW626Vde-V2 Back anchoring in traverse W626Vde-H2 Back anchoring in traverse Vertical section Horizontal section
Sanistand withconcealed mount cistern
SealantUD profile made of insulation strips
UW runner
UW runner
UA profile
Knauf multi-purpose screw FN
Uniflott + Trenn-Fix
Multi-purpose traverse 555 300 23 mm
Knauf connection bracket withenclosed M8 carriage bolts
2x 125 mm DiamantDiamant screw XTB
Knauf connection bracket withenclosed M8 carriage bolt
Wall anchor installation acc to WCSanistand manufacturer specifications
Knauf sealing tape
Stud spacing le 625 mm
Multi-purpose traverse555 300 23 mm
UA profile
UA profile
Knauf connection bracket withenclosed M8 carriage bolt
Knauf connectionbracket with enclosedM8 carriage bolt
Wall anchorinstallation acc to
WC Sanistandmanufacturerspecifications
Notes
Max partition height rear W112de UA 50 = 300 m UA 75 = see system data sheet W11de Knauf Metal Stud Partitions for the wall heights
Minimum cladding front wall installations ge 18 mm Knauf Boards recommendation 2x 125 mm Knauf Diamant
Web cutouts are not permissible in UA Sanistand subject to cantilever loads point loads or linear distributed loadsObserve the manufacturersrsquo details for lateral UA profiles and cladding Additional UA profiles are required laterally on Sanistand mounts acc to DIN 18340 section 374 Only possible without additional UA profiles if the manufacturer of the Sanistand base or WC Sanistand permits itDeviating specifications of the Sanistand manufacturer must be considered and observed
19
Loads on partitions and furringsFull-length Sanistand
Scale 110DetailsW626Vde-V3 Back anchoring in UA profile W626Vde-H3 Back anchoring in UA profile Vertical section Horizontal section
Sanistand withconcealed mount cistern
SealantUD profile on insulation strips
UW runner
UW runner
Additional UA profile
Knauf multi-purpose screw FN
Uniflott + Trenn-Fix
UA profile
Knauf connection bracket withenclosed M8 carriage bolts
2x 125 mm DiamantDiamant screw XTB
Knauf connection bracket withenclosed M8 carriage bolts
Fixing bolts with nuts andwashers
Knauf sealing tape
Stud spacing le 625 mm
Additional UA profile
UA profile Fixing bolts with nutsand washers
Knauf connection bracket withenclosed M8 carriage bolts
Knauf connectionbracket with enclosedM8 carriage bolts
Notes
Max partition height at rear W112de UA 50 = 300 m UA 75 = see system data sheet W11de Knauf Metal Stud Partition for the wall heights
Minimum cladding front wall installations ge 18 mm Knauf Boards recommendation 2x 125 mm Knauf Diamant
Web cutouts are not permissible in UA Sanistand subject to cantilever loads point loads or linear distributed loadsObserve the manufacturersrsquo details for lateral UA profiles and cladding Additional UA profiles are required laterally on Sanistand mounts acc to DIN 18340 section 374 Only possible without additional UA profiles if the manufacturer of the Sanistand base or WC Sanistand permits itDeviating specifications of the Sanistand manufacturer must be considered and observed
20
Loads on partitions and furringsFull-length Sanistand
Scale 110DetailsW626Vde-V4 Back anchoring in mounting rail W626Vde-H4 Back anchoring in mounting rail Vertical section Horizontal section
Sanistand withconcealed mount cistern
2x 125 mm Diamant
SealantUD profile on insulation strips
UW runner
Diamant screw XTB
UA profile
Knauf multi-purpose screw FN
Mounting rail with fixing screw
Knauf connection bracket withenclosed M8 carriage bolt
Uniflott + Trenn-Fix
UA profile
Knauf connection bracket withenclosed M8 carriage bolt
Knauf sealing tapeUW runner
Stud spacing le 625 mm
UA profile
UA profile
Mounting railFixing screw
Mounting screw
Sanistand withconcealed mount cistern
Knauf connection bracket withenclosed M8 carriage bolt
Knauf connectionbracket with enclosedM8 carriage bolt
Notes
Max partition height rear W112de UA 50 = 300 m UA 75 = see system data sheet W11de Knauf Metal Stud Partitions for the wall heights
Minimum cladding front wall installations ge 18 mm Knauf Boards recommendation 2x 125 mm Knauf Diamant
Web cutouts are not permissible in UA Sanistand subject to cantilever loads point loads or linear distributed loadsObserve the manufacturersrsquo details for lateral UA profiles and cladding Additional UA profiles are required laterally on Sanistand mounts acc to DIN 18340 section 374 Only possible without additional UA profiles if the manufacturer of the Sanistand base or WC Sanistand permits itDeviating specifications of the Sanistand manufacturer must be considered and observed
21
Notes
In case of load attachment to ldquomulti-level ceiling systemsrdquo refer to the respective valid Knauf system data sheetsIn case of attachment of loads to free-spanning ceilings see system data sheet D13de Knauf Free-Spanning Ceilings
Attachment of loads to Knauf board ceilingsAdditional loads eg lighting fixtures curtain rails and similar can be fixed to Knauf board ceilings using universal dowels cavity dowels spring toggle dowels or Knauf Hartmut Hohlraumduumlbel cavity dowelsAdditional loads must be considered when determining the load class
NoteHeavy loads must be attached directly on load-bearing building elements (basic ceiling) or on auxiliary constructions eg traverses
For each area under load of the Knauf board ceiling the weight of thefastened components may not exceed the following limits
Permissible weight per ceiling area in kgmsup2Without fire resistance With fire resistance1)
15 61)Incaseofapplicationasafireresistanceceilingwithexposedceiling(multi-levelceilingsystem)15kgmsup2totalweightispermissiblefortheexposedceiling(includinginsulationlayerandattachedloads)attachedtothefireresistanceceiling
Furthermore the following conditions applyFor each anchoring point the components fastened to the board ceiling may not exceed the following weights
Fastening method Permissible weight per anchoring point in kgWithout fire resistance With fire resistance
Fastening in the cladding 6 05
Fastening to the grid 10 10
Fastening in the claddingKnauf Hartmut Hohlraumduumlbel cavity dowelScrew M5
Fastening to the gridKnauf Universalschraube FN multi-purpose screw eg curtain rail
The minimum separation spacings between individual attached loads must be observed to avoid local overloading of the ceiling The minimum separation clearance between two attachment points consists of both load radii for the point loadsThe load radius of a point load can be taken from the following diagram in dependence on the permissible weight per unit area for additional loads
Point load in kg
7570656055504540353025201510
0 2 3 4 5 6 7 8 9 10
Radiu
s in c
m
1
50
Fastening in the claddingpossible (without fire resistance)
3 kgmsup2 permissible additional weight (on the exposed ceiling under a fire resistance ceiling refer to the respective valid Knauf system data sheets)6 kgmsup2 permissible additional weight (with fire resistance)15 kgmsup2 permissible additional weight (without fire resistance)
Example fastening scheme at 15 kgmsup2
05 kg
10 kg
3 kgr = 25 cm
r = 46 cm
6 kgr = 355 cm
1 kg
r = 15 cm
r = 105 cm
NoteThe anchored loads can be transferred using several anchoring elements
Loads on board ceilingsFastening in the cladding grid
22
Knauf multi-purpose traversesThe multi-purpose traverse in Knauf board ceilings is suitable for the application of point loads up to 075 kN eg chandeliers music speakers or similarThe multi-purpose traverse consists of a 23 mm thick multi-layer wooden board and galvanized sheet metal profiles It is fastened to the side of the CD furring channelThe attachment of the loads to the traverses should be performed using Knauf Multi-Purpose Screw FNInstallation is possible in a double layer profile grid and flush profile grid
Installation and applicationBend the Daisy chain clip before lateral screw fastening The Daisy chain clip is then Z shaped The unpunched metal side of the Daisy chain clip is pushed onto the lower side of the traverse and then screw fastened laterally through the factory-made hole on the long side of the traverse Screw fasten 4x Daisy chain clips each using one drywall screw TN 35 x 35 about 100 mm from the corner of the multi-layer board on the long edge of the multi-purpose traverse Arrange an additional CD channel (length ge 650 mm) for every long edge in accordance with the width of the multi-purpose traverse Alternately a ceiling furring channel can be used for application of the multi-purpose traverse The supporting profiles are suspended using ceiling suspenders of load class 40 kg The suspenders may not be situated in the direct vicinity of the longitudinal area of the traverse as this will hinder the installation of the traverse Introduce the multi-purpose traverse between the support profiles bend the Daisy chain clip around the CD channel and engage it In case of single-layer cladding do not screw fasten the surface cladding with the multi-purpose traverse
1 Apply the Daisy chain clip 2 Bend the Daisy chain clip 3 Screw fasten the Daisy chain clip
Loads on board ceilingsAnchoring in the traverses
100 mm
23
Loads on board ceilingsAnchoring in the traverses
Scale 110 I Dimensions in mmDetailsD112de SO18 Vertical section ndash Multi-purpose traverse D113de SO12 Vertical section ndash Multi-purpose traverseeg with two additional CD channels I Without fire resistance eg with one additional CD channel I Without fire resistance
D112de SO19 Vertical section ndash Multi-purpose traverse D113de SO13 Vertical section ndash Multi-purpose traverseeg with two additional CD channels I Without fire resistance eg with one additional CD channel I Without fire resistance
D112de SO20 Top view ndash Multi-purpose traverse D113de SO14 Top view ndash Multi-purpose traverseeg with two additional CD channels I Without fire resistance eg with one additional CD channel I Without fire resistance
Fasten Daisy chain clip with drywall screwTN 35 x 35 to multi-purpose traverse
Additional CD channel with two suspendersLoad bearing capacity class ge 040 kN
Multi-purposetraverse555 300 23 mm
300
Furring channel spacing 500
Fasten Daisy chain clip with drywall screwTN 35 x 35 to multi-purpose traverse
Additional suspended load bearing capacity class ge 040 kNMulti-purposetraverse555 300 23 mm
300
Furring channel spacing 500
Additional CD channel with two suspendersLoad bearing capacity class ge 040 kN
Multi-purposetraverse555 300 23 mm
Fasten Daisy chain clip with drywall screwTN 35 x 35 to multi-purpose traverse
Wood panel 555approx
100
Additional suspenderload bearing capacityclass ge 040 kN
Multi-purposetraverse555 300 23 mm
Fasten Daisy chain clip with drywall screwTN 35 x 35 to multi-purpose traverse
Wood panel 555approx
100
Daisy chain clip
Furring channel spacing 500
Traverse
CDchannel
Multi-layerwood panel
Furring channel spacing 500
Multi-purposetraverse
Daisy chain clip
Multi-layerwood panel
Additional grid 4 additional suspension points (eg Nonius suspension)
All technical changes reserved Only the current printed instructions are valid The stated information represents current state-of-the-art Knauf technology The entire state of approved engineering rules appropriate standards guidelines and rules of crafts-manship are not included herewith These and all application instructions have to be adhered to separately by the installer Our warranty is expressly limited to our products in flawless condition All application quantities and delivery amounts are based on empirical data that are not easily transferable to other deviating areasAll rights reserved All amendments reprints and photocopies including those of excerpts require our expressed permission
The stated constructional and structural design specifications and characteristics of building physics of Knauf systems can only be ensured with the exclusive use of Knauf system components or other products expressly recommended by Knauf
Knauf Gips KG Am Bahnhof 7 97346 Iphofen GermanyKnauf DirectTechnical Advisory Service
knauf-direktknaufde
wwwknaufde
VT03deeng09190TI
The iPad App Knauf Infothek now provides all the current information and documents from Knauf Gips KG at any time and in every location in a clear and comfortable wayKnauf Infothek
Videos for Knauf systems and products can be found under the following linkwwwyoutubecomknaufEPD
14
Loads on partitions and furringsAnchoring in the traverses
Knauf steel anchoring traverseThe steel anchoring traverse is suitable for accepting loads attached to the wall up to 10 kNm wall length eg towel holders cupboards shelves and similar Not suitable for dynamic loads such as folding wall attached seatsThe steel anchoring traverse consists of 075 mm thick sheet metal and are crimped onto the side using a stud crimper on the CW studs Particularly suitable for single-layer clad metal stud partitions and furrings where in case of cantilever loads gt 04 kNm (400 kgm) wall length the installation of a traverse is required
NoteTraverses for installation in damp and wet rooms see also system data sheet W38de Knauf Metal Stud Partitions AQUAPANELreg
Installation and applicationCrimp the steel anchoring traverse made of galvanized sheet steel to the CW studs using a Stud CrimperAdditional screw fastening of the steel anchoring traverse via screw fastening of the cladding (min 2 to 3 anchoring points) Reduce the screw spacing of the cladding if necessaryArrangement in a rowCW studs
Scale 110 I Dimensions in mmDetailsW234de-A11 View W234de V11 Vertical section
eg W111de
W234de-H11 Horizontal sectioneg W111de
Sheet metal gauge 075 mm
Steel anchoring traverse
CW stud
Crimp the traverse to the CW studusing the stud crimper
290
Traverse dimension 620
Stud spacing 625 (grid dimension)
eg Cabinet
CW stud
Knauf boardSteel anchoring traverse
Steel anchoring traverseCW stud
Crimped
Note No web cutouts in the CW studs are permissible for traverses to which the CW studs are attached
15
Full-length SanistandFloor-to-ceiling Sanistands made of galvanized UA profiles (min UA 75) 2 mm thick are suitable for transferring loads from traverses into the supporting structure or for fixing loads hanging onto walls such as school blackboards up to 15 kNm wall lengthFloor-to-ceiling Sanistands profiles are anchored to the basic floor and ceiling with door frame brackets or connection brackets for UA profiles The upper door frame bracket includes openings for routing cables such as pipe-in-pipe systems or electrical cablesThe loads are connected directly to the flange of the UA profile
W228de-A10 View
le 1000 mm
UW runnercontinuous
Door frameconnection brackettop connection withenclosed dowels
CW studAxial spacing suitedto partition system
UA profileas afloor-to-ceilingSanistand forbearing cantileverloads
UW runnercontinuous
Door frameconnection bracketbottom connectionwith enclosed dowels
Scale 110
Installation and applicationFloor-to-ceiling Sanistands made of UA profiles must be anchored to the basic floor and ceiling with door frame brackets or connection brackets for UA profiles The upper door frame bracket includes openings for routing cables such as pipe-in-pipe systems or electrical cables Fasten objects to UA profiles using threaded rods U washers and M1012 steel nuts or self-tapping screws
Loads on partitions and furringsFull-length Sanistand
Detail
Notes
Web cutouts are not permissible in UA Sanistand subject to cantilever loads point loads or linear distributed loadsMaximum screw load with connections to full height Sanistand (UA profile)Every UA profile flange and anchoring point may not exceed a resulting pull-out load of 150 kN (150 kg)Components similar to cantilevers such as foldable rails should be screwed onto two adjacent UA profilesUse suitable drilling screws eg Ejot Zebra Piasta Hilti S-MD or comparable
16
Loads on partitions and furringsFull-length Sanistand
Scale 110DetailsW116de-V1 Sanistand W116de-H1 SanistandVertical section I Without fire resistance Horizontal section I Without fire resistance
UW runnerUniflott + Trenn-Fix
UW runner
Additional UA profile
Sanistand withconcealed mount cistern
Knauf connectionbracket with enclosedM8 carriage bolts
Knauf conection bracket withenclosed M8 carriage bolt
2x 125 mm DiamantDiamant screw XTB
Additional CW stud
Knauf sealing tape
Board strip installationacc to W11de systemdata sheet
Stud spacing le 625 mm
CW stud profile
Additional CW studBoard strip installation in acc with W11de system data sheet
Knauf connection bracket withenclosed M8 carriage bolts
Additional UA profileSanitand with concealedmount cistern
Notes
Max partition height UA 50 = 300 m UA 75 = see system data sheet W11de Knauf Metal Stud Partition for the wall heights
Minimum cladding ge 18 mm Knauf Boards recommendation 2x 125 mm Knauf Diamant
Web cutouts are not permissible in UA Sanistand subject to cantilever loads point loads or linear distributed loadsObserve the manufacturersrsquo details for lateral UA profiles and cladding Additional UA profiles are required laterally on Sanistand mounts acc to DIN 18340 section 374 Only possible without additional UA profiles if the manufacturer of the Sanistand base or WC Sanistand permits itDeviating specifications of the Sanistand manufacturer must be considered and observed
17
Loads on partitions and furringsFull-length Sanistand
Notes
Max partition height rear W112de UA 50 = 300 m UA 75 = see system data sheet W11de Knauf Metal Stud Partition for the wall heights
Minimum cladding front wall installations ge 18 mm Knauf Boards recommendation 2x 125 mm Knauf Diamant
Web cutouts are not permissible in UA Sanistand subject to cantilever loads point loads or linear distributed loadsObserve the manufacturersrsquo details for lateral UA profiles and cladding Additional UA profiles are required laterally on Sanistand mounts acc to DIN 18340 section 374 Only possible without additional UA profiles if the manufacturer of the Sanistand base or WC Sanistand permits itDeviating specifications of the Sanistand manufacturer must be considered and observed
Scale 110DetailsW626Vde-V1 Without back anchoring W626Vde-H1 Without back anchoring Vertical section Horizontal section
UW runnerUniflott + Trenn-Fix
UW runner
Additional UA profile
Sanistand withconcealed mount cistern
Knauf connection bracket withenclosed M8 carriage bolt
Knauf connection bracket withenclosed M8 carriage bolt
2x 125 mm DiamantDiamant screw XTB
Knauf sealing tape
Sanistand withconcealed mount cisternKnauf connection bracket with
enclosed M8 carriage bolts
Stud spacing le 625 mm
UW runner
Knauf boardsCW stud
Additional UA profile
18
Loads on partitions and furringsFull-length Sanistand
Scale 110DetailsW626Vde-V2 Back anchoring in traverse W626Vde-H2 Back anchoring in traverse Vertical section Horizontal section
Sanistand withconcealed mount cistern
SealantUD profile made of insulation strips
UW runner
UW runner
UA profile
Knauf multi-purpose screw FN
Uniflott + Trenn-Fix
Multi-purpose traverse 555 300 23 mm
Knauf connection bracket withenclosed M8 carriage bolts
2x 125 mm DiamantDiamant screw XTB
Knauf connection bracket withenclosed M8 carriage bolt
Wall anchor installation acc to WCSanistand manufacturer specifications
Knauf sealing tape
Stud spacing le 625 mm
Multi-purpose traverse555 300 23 mm
UA profile
UA profile
Knauf connection bracket withenclosed M8 carriage bolt
Knauf connectionbracket with enclosedM8 carriage bolt
Wall anchorinstallation acc to
WC Sanistandmanufacturerspecifications
Notes
Max partition height rear W112de UA 50 = 300 m UA 75 = see system data sheet W11de Knauf Metal Stud Partitions for the wall heights
Minimum cladding front wall installations ge 18 mm Knauf Boards recommendation 2x 125 mm Knauf Diamant
Web cutouts are not permissible in UA Sanistand subject to cantilever loads point loads or linear distributed loadsObserve the manufacturersrsquo details for lateral UA profiles and cladding Additional UA profiles are required laterally on Sanistand mounts acc to DIN 18340 section 374 Only possible without additional UA profiles if the manufacturer of the Sanistand base or WC Sanistand permits itDeviating specifications of the Sanistand manufacturer must be considered and observed
19
Loads on partitions and furringsFull-length Sanistand
Scale 110DetailsW626Vde-V3 Back anchoring in UA profile W626Vde-H3 Back anchoring in UA profile Vertical section Horizontal section
Sanistand withconcealed mount cistern
SealantUD profile on insulation strips
UW runner
UW runner
Additional UA profile
Knauf multi-purpose screw FN
Uniflott + Trenn-Fix
UA profile
Knauf connection bracket withenclosed M8 carriage bolts
2x 125 mm DiamantDiamant screw XTB
Knauf connection bracket withenclosed M8 carriage bolts
Fixing bolts with nuts andwashers
Knauf sealing tape
Stud spacing le 625 mm
Additional UA profile
UA profile Fixing bolts with nutsand washers
Knauf connection bracket withenclosed M8 carriage bolts
Knauf connectionbracket with enclosedM8 carriage bolts
Notes
Max partition height at rear W112de UA 50 = 300 m UA 75 = see system data sheet W11de Knauf Metal Stud Partition for the wall heights
Minimum cladding front wall installations ge 18 mm Knauf Boards recommendation 2x 125 mm Knauf Diamant
Web cutouts are not permissible in UA Sanistand subject to cantilever loads point loads or linear distributed loadsObserve the manufacturersrsquo details for lateral UA profiles and cladding Additional UA profiles are required laterally on Sanistand mounts acc to DIN 18340 section 374 Only possible without additional UA profiles if the manufacturer of the Sanistand base or WC Sanistand permits itDeviating specifications of the Sanistand manufacturer must be considered and observed
20
Loads on partitions and furringsFull-length Sanistand
Scale 110DetailsW626Vde-V4 Back anchoring in mounting rail W626Vde-H4 Back anchoring in mounting rail Vertical section Horizontal section
Sanistand withconcealed mount cistern
2x 125 mm Diamant
SealantUD profile on insulation strips
UW runner
Diamant screw XTB
UA profile
Knauf multi-purpose screw FN
Mounting rail with fixing screw
Knauf connection bracket withenclosed M8 carriage bolt
Uniflott + Trenn-Fix
UA profile
Knauf connection bracket withenclosed M8 carriage bolt
Knauf sealing tapeUW runner
Stud spacing le 625 mm
UA profile
UA profile
Mounting railFixing screw
Mounting screw
Sanistand withconcealed mount cistern
Knauf connection bracket withenclosed M8 carriage bolt
Knauf connectionbracket with enclosedM8 carriage bolt
Notes
Max partition height rear W112de UA 50 = 300 m UA 75 = see system data sheet W11de Knauf Metal Stud Partitions for the wall heights
Minimum cladding front wall installations ge 18 mm Knauf Boards recommendation 2x 125 mm Knauf Diamant
Web cutouts are not permissible in UA Sanistand subject to cantilever loads point loads or linear distributed loadsObserve the manufacturersrsquo details for lateral UA profiles and cladding Additional UA profiles are required laterally on Sanistand mounts acc to DIN 18340 section 374 Only possible without additional UA profiles if the manufacturer of the Sanistand base or WC Sanistand permits itDeviating specifications of the Sanistand manufacturer must be considered and observed
21
Notes
In case of load attachment to ldquomulti-level ceiling systemsrdquo refer to the respective valid Knauf system data sheetsIn case of attachment of loads to free-spanning ceilings see system data sheet D13de Knauf Free-Spanning Ceilings
Attachment of loads to Knauf board ceilingsAdditional loads eg lighting fixtures curtain rails and similar can be fixed to Knauf board ceilings using universal dowels cavity dowels spring toggle dowels or Knauf Hartmut Hohlraumduumlbel cavity dowelsAdditional loads must be considered when determining the load class
NoteHeavy loads must be attached directly on load-bearing building elements (basic ceiling) or on auxiliary constructions eg traverses
For each area under load of the Knauf board ceiling the weight of thefastened components may not exceed the following limits
Permissible weight per ceiling area in kgmsup2Without fire resistance With fire resistance1)
15 61)Incaseofapplicationasafireresistanceceilingwithexposedceiling(multi-levelceilingsystem)15kgmsup2totalweightispermissiblefortheexposedceiling(includinginsulationlayerandattachedloads)attachedtothefireresistanceceiling
Furthermore the following conditions applyFor each anchoring point the components fastened to the board ceiling may not exceed the following weights
Fastening method Permissible weight per anchoring point in kgWithout fire resistance With fire resistance
Fastening in the cladding 6 05
Fastening to the grid 10 10
Fastening in the claddingKnauf Hartmut Hohlraumduumlbel cavity dowelScrew M5
Fastening to the gridKnauf Universalschraube FN multi-purpose screw eg curtain rail
The minimum separation spacings between individual attached loads must be observed to avoid local overloading of the ceiling The minimum separation clearance between two attachment points consists of both load radii for the point loadsThe load radius of a point load can be taken from the following diagram in dependence on the permissible weight per unit area for additional loads
Point load in kg
7570656055504540353025201510
0 2 3 4 5 6 7 8 9 10
Radiu
s in c
m
1
50
Fastening in the claddingpossible (without fire resistance)
3 kgmsup2 permissible additional weight (on the exposed ceiling under a fire resistance ceiling refer to the respective valid Knauf system data sheets)6 kgmsup2 permissible additional weight (with fire resistance)15 kgmsup2 permissible additional weight (without fire resistance)
Example fastening scheme at 15 kgmsup2
05 kg
10 kg
3 kgr = 25 cm
r = 46 cm
6 kgr = 355 cm
1 kg
r = 15 cm
r = 105 cm
NoteThe anchored loads can be transferred using several anchoring elements
Loads on board ceilingsFastening in the cladding grid
22
Knauf multi-purpose traversesThe multi-purpose traverse in Knauf board ceilings is suitable for the application of point loads up to 075 kN eg chandeliers music speakers or similarThe multi-purpose traverse consists of a 23 mm thick multi-layer wooden board and galvanized sheet metal profiles It is fastened to the side of the CD furring channelThe attachment of the loads to the traverses should be performed using Knauf Multi-Purpose Screw FNInstallation is possible in a double layer profile grid and flush profile grid
Installation and applicationBend the Daisy chain clip before lateral screw fastening The Daisy chain clip is then Z shaped The unpunched metal side of the Daisy chain clip is pushed onto the lower side of the traverse and then screw fastened laterally through the factory-made hole on the long side of the traverse Screw fasten 4x Daisy chain clips each using one drywall screw TN 35 x 35 about 100 mm from the corner of the multi-layer board on the long edge of the multi-purpose traverse Arrange an additional CD channel (length ge 650 mm) for every long edge in accordance with the width of the multi-purpose traverse Alternately a ceiling furring channel can be used for application of the multi-purpose traverse The supporting profiles are suspended using ceiling suspenders of load class 40 kg The suspenders may not be situated in the direct vicinity of the longitudinal area of the traverse as this will hinder the installation of the traverse Introduce the multi-purpose traverse between the support profiles bend the Daisy chain clip around the CD channel and engage it In case of single-layer cladding do not screw fasten the surface cladding with the multi-purpose traverse
1 Apply the Daisy chain clip 2 Bend the Daisy chain clip 3 Screw fasten the Daisy chain clip
Loads on board ceilingsAnchoring in the traverses
100 mm
23
Loads on board ceilingsAnchoring in the traverses
Scale 110 I Dimensions in mmDetailsD112de SO18 Vertical section ndash Multi-purpose traverse D113de SO12 Vertical section ndash Multi-purpose traverseeg with two additional CD channels I Without fire resistance eg with one additional CD channel I Without fire resistance
D112de SO19 Vertical section ndash Multi-purpose traverse D113de SO13 Vertical section ndash Multi-purpose traverseeg with two additional CD channels I Without fire resistance eg with one additional CD channel I Without fire resistance
D112de SO20 Top view ndash Multi-purpose traverse D113de SO14 Top view ndash Multi-purpose traverseeg with two additional CD channels I Without fire resistance eg with one additional CD channel I Without fire resistance
Fasten Daisy chain clip with drywall screwTN 35 x 35 to multi-purpose traverse
Additional CD channel with two suspendersLoad bearing capacity class ge 040 kN
Multi-purposetraverse555 300 23 mm
300
Furring channel spacing 500
Fasten Daisy chain clip with drywall screwTN 35 x 35 to multi-purpose traverse
Additional suspended load bearing capacity class ge 040 kNMulti-purposetraverse555 300 23 mm
300
Furring channel spacing 500
Additional CD channel with two suspendersLoad bearing capacity class ge 040 kN
Multi-purposetraverse555 300 23 mm
Fasten Daisy chain clip with drywall screwTN 35 x 35 to multi-purpose traverse
Wood panel 555approx
100
Additional suspenderload bearing capacityclass ge 040 kN
Multi-purposetraverse555 300 23 mm
Fasten Daisy chain clip with drywall screwTN 35 x 35 to multi-purpose traverse
Wood panel 555approx
100
Daisy chain clip
Furring channel spacing 500
Traverse
CDchannel
Multi-layerwood panel
Furring channel spacing 500
Multi-purposetraverse
Daisy chain clip
Multi-layerwood panel
Additional grid 4 additional suspension points (eg Nonius suspension)
All technical changes reserved Only the current printed instructions are valid The stated information represents current state-of-the-art Knauf technology The entire state of approved engineering rules appropriate standards guidelines and rules of crafts-manship are not included herewith These and all application instructions have to be adhered to separately by the installer Our warranty is expressly limited to our products in flawless condition All application quantities and delivery amounts are based on empirical data that are not easily transferable to other deviating areasAll rights reserved All amendments reprints and photocopies including those of excerpts require our expressed permission
The stated constructional and structural design specifications and characteristics of building physics of Knauf systems can only be ensured with the exclusive use of Knauf system components or other products expressly recommended by Knauf
Knauf Gips KG Am Bahnhof 7 97346 Iphofen GermanyKnauf DirectTechnical Advisory Service
knauf-direktknaufde
wwwknaufde
VT03deeng09190TI
The iPad App Knauf Infothek now provides all the current information and documents from Knauf Gips KG at any time and in every location in a clear and comfortable wayKnauf Infothek
Videos for Knauf systems and products can be found under the following linkwwwyoutubecomknaufEPD
15
Full-length SanistandFloor-to-ceiling Sanistands made of galvanized UA profiles (min UA 75) 2 mm thick are suitable for transferring loads from traverses into the supporting structure or for fixing loads hanging onto walls such as school blackboards up to 15 kNm wall lengthFloor-to-ceiling Sanistands profiles are anchored to the basic floor and ceiling with door frame brackets or connection brackets for UA profiles The upper door frame bracket includes openings for routing cables such as pipe-in-pipe systems or electrical cablesThe loads are connected directly to the flange of the UA profile
W228de-A10 View
le 1000 mm
UW runnercontinuous
Door frameconnection brackettop connection withenclosed dowels
CW studAxial spacing suitedto partition system
UA profileas afloor-to-ceilingSanistand forbearing cantileverloads
UW runnercontinuous
Door frameconnection bracketbottom connectionwith enclosed dowels
Scale 110
Installation and applicationFloor-to-ceiling Sanistands made of UA profiles must be anchored to the basic floor and ceiling with door frame brackets or connection brackets for UA profiles The upper door frame bracket includes openings for routing cables such as pipe-in-pipe systems or electrical cables Fasten objects to UA profiles using threaded rods U washers and M1012 steel nuts or self-tapping screws
Loads on partitions and furringsFull-length Sanistand
Detail
Notes
Web cutouts are not permissible in UA Sanistand subject to cantilever loads point loads or linear distributed loadsMaximum screw load with connections to full height Sanistand (UA profile)Every UA profile flange and anchoring point may not exceed a resulting pull-out load of 150 kN (150 kg)Components similar to cantilevers such as foldable rails should be screwed onto two adjacent UA profilesUse suitable drilling screws eg Ejot Zebra Piasta Hilti S-MD or comparable
16
Loads on partitions and furringsFull-length Sanistand
Scale 110DetailsW116de-V1 Sanistand W116de-H1 SanistandVertical section I Without fire resistance Horizontal section I Without fire resistance
UW runnerUniflott + Trenn-Fix
UW runner
Additional UA profile
Sanistand withconcealed mount cistern
Knauf connectionbracket with enclosedM8 carriage bolts
Knauf conection bracket withenclosed M8 carriage bolt
2x 125 mm DiamantDiamant screw XTB
Additional CW stud
Knauf sealing tape
Board strip installationacc to W11de systemdata sheet
Stud spacing le 625 mm
CW stud profile
Additional CW studBoard strip installation in acc with W11de system data sheet
Knauf connection bracket withenclosed M8 carriage bolts
Additional UA profileSanitand with concealedmount cistern
Notes
Max partition height UA 50 = 300 m UA 75 = see system data sheet W11de Knauf Metal Stud Partition for the wall heights
Minimum cladding ge 18 mm Knauf Boards recommendation 2x 125 mm Knauf Diamant
Web cutouts are not permissible in UA Sanistand subject to cantilever loads point loads or linear distributed loadsObserve the manufacturersrsquo details for lateral UA profiles and cladding Additional UA profiles are required laterally on Sanistand mounts acc to DIN 18340 section 374 Only possible without additional UA profiles if the manufacturer of the Sanistand base or WC Sanistand permits itDeviating specifications of the Sanistand manufacturer must be considered and observed
17
Loads on partitions and furringsFull-length Sanistand
Notes
Max partition height rear W112de UA 50 = 300 m UA 75 = see system data sheet W11de Knauf Metal Stud Partition for the wall heights
Minimum cladding front wall installations ge 18 mm Knauf Boards recommendation 2x 125 mm Knauf Diamant
Web cutouts are not permissible in UA Sanistand subject to cantilever loads point loads or linear distributed loadsObserve the manufacturersrsquo details for lateral UA profiles and cladding Additional UA profiles are required laterally on Sanistand mounts acc to DIN 18340 section 374 Only possible without additional UA profiles if the manufacturer of the Sanistand base or WC Sanistand permits itDeviating specifications of the Sanistand manufacturer must be considered and observed
Scale 110DetailsW626Vde-V1 Without back anchoring W626Vde-H1 Without back anchoring Vertical section Horizontal section
UW runnerUniflott + Trenn-Fix
UW runner
Additional UA profile
Sanistand withconcealed mount cistern
Knauf connection bracket withenclosed M8 carriage bolt
Knauf connection bracket withenclosed M8 carriage bolt
2x 125 mm DiamantDiamant screw XTB
Knauf sealing tape
Sanistand withconcealed mount cisternKnauf connection bracket with
enclosed M8 carriage bolts
Stud spacing le 625 mm
UW runner
Knauf boardsCW stud
Additional UA profile
18
Loads on partitions and furringsFull-length Sanistand
Scale 110DetailsW626Vde-V2 Back anchoring in traverse W626Vde-H2 Back anchoring in traverse Vertical section Horizontal section
Sanistand withconcealed mount cistern
SealantUD profile made of insulation strips
UW runner
UW runner
UA profile
Knauf multi-purpose screw FN
Uniflott + Trenn-Fix
Multi-purpose traverse 555 300 23 mm
Knauf connection bracket withenclosed M8 carriage bolts
2x 125 mm DiamantDiamant screw XTB
Knauf connection bracket withenclosed M8 carriage bolt
Wall anchor installation acc to WCSanistand manufacturer specifications
Knauf sealing tape
Stud spacing le 625 mm
Multi-purpose traverse555 300 23 mm
UA profile
UA profile
Knauf connection bracket withenclosed M8 carriage bolt
Knauf connectionbracket with enclosedM8 carriage bolt
Wall anchorinstallation acc to
WC Sanistandmanufacturerspecifications
Notes
Max partition height rear W112de UA 50 = 300 m UA 75 = see system data sheet W11de Knauf Metal Stud Partitions for the wall heights
Minimum cladding front wall installations ge 18 mm Knauf Boards recommendation 2x 125 mm Knauf Diamant
Web cutouts are not permissible in UA Sanistand subject to cantilever loads point loads or linear distributed loadsObserve the manufacturersrsquo details for lateral UA profiles and cladding Additional UA profiles are required laterally on Sanistand mounts acc to DIN 18340 section 374 Only possible without additional UA profiles if the manufacturer of the Sanistand base or WC Sanistand permits itDeviating specifications of the Sanistand manufacturer must be considered and observed
19
Loads on partitions and furringsFull-length Sanistand
Scale 110DetailsW626Vde-V3 Back anchoring in UA profile W626Vde-H3 Back anchoring in UA profile Vertical section Horizontal section
Sanistand withconcealed mount cistern
SealantUD profile on insulation strips
UW runner
UW runner
Additional UA profile
Knauf multi-purpose screw FN
Uniflott + Trenn-Fix
UA profile
Knauf connection bracket withenclosed M8 carriage bolts
2x 125 mm DiamantDiamant screw XTB
Knauf connection bracket withenclosed M8 carriage bolts
Fixing bolts with nuts andwashers
Knauf sealing tape
Stud spacing le 625 mm
Additional UA profile
UA profile Fixing bolts with nutsand washers
Knauf connection bracket withenclosed M8 carriage bolts
Knauf connectionbracket with enclosedM8 carriage bolts
Notes
Max partition height at rear W112de UA 50 = 300 m UA 75 = see system data sheet W11de Knauf Metal Stud Partition for the wall heights
Minimum cladding front wall installations ge 18 mm Knauf Boards recommendation 2x 125 mm Knauf Diamant
Web cutouts are not permissible in UA Sanistand subject to cantilever loads point loads or linear distributed loadsObserve the manufacturersrsquo details for lateral UA profiles and cladding Additional UA profiles are required laterally on Sanistand mounts acc to DIN 18340 section 374 Only possible without additional UA profiles if the manufacturer of the Sanistand base or WC Sanistand permits itDeviating specifications of the Sanistand manufacturer must be considered and observed
20
Loads on partitions and furringsFull-length Sanistand
Scale 110DetailsW626Vde-V4 Back anchoring in mounting rail W626Vde-H4 Back anchoring in mounting rail Vertical section Horizontal section
Sanistand withconcealed mount cistern
2x 125 mm Diamant
SealantUD profile on insulation strips
UW runner
Diamant screw XTB
UA profile
Knauf multi-purpose screw FN
Mounting rail with fixing screw
Knauf connection bracket withenclosed M8 carriage bolt
Uniflott + Trenn-Fix
UA profile
Knauf connection bracket withenclosed M8 carriage bolt
Knauf sealing tapeUW runner
Stud spacing le 625 mm
UA profile
UA profile
Mounting railFixing screw
Mounting screw
Sanistand withconcealed mount cistern
Knauf connection bracket withenclosed M8 carriage bolt
Knauf connectionbracket with enclosedM8 carriage bolt
Notes
Max partition height rear W112de UA 50 = 300 m UA 75 = see system data sheet W11de Knauf Metal Stud Partitions for the wall heights
Minimum cladding front wall installations ge 18 mm Knauf Boards recommendation 2x 125 mm Knauf Diamant
Web cutouts are not permissible in UA Sanistand subject to cantilever loads point loads or linear distributed loadsObserve the manufacturersrsquo details for lateral UA profiles and cladding Additional UA profiles are required laterally on Sanistand mounts acc to DIN 18340 section 374 Only possible without additional UA profiles if the manufacturer of the Sanistand base or WC Sanistand permits itDeviating specifications of the Sanistand manufacturer must be considered and observed
21
Notes
In case of load attachment to ldquomulti-level ceiling systemsrdquo refer to the respective valid Knauf system data sheetsIn case of attachment of loads to free-spanning ceilings see system data sheet D13de Knauf Free-Spanning Ceilings
Attachment of loads to Knauf board ceilingsAdditional loads eg lighting fixtures curtain rails and similar can be fixed to Knauf board ceilings using universal dowels cavity dowels spring toggle dowels or Knauf Hartmut Hohlraumduumlbel cavity dowelsAdditional loads must be considered when determining the load class
NoteHeavy loads must be attached directly on load-bearing building elements (basic ceiling) or on auxiliary constructions eg traverses
For each area under load of the Knauf board ceiling the weight of thefastened components may not exceed the following limits
Permissible weight per ceiling area in kgmsup2Without fire resistance With fire resistance1)
15 61)Incaseofapplicationasafireresistanceceilingwithexposedceiling(multi-levelceilingsystem)15kgmsup2totalweightispermissiblefortheexposedceiling(includinginsulationlayerandattachedloads)attachedtothefireresistanceceiling
Furthermore the following conditions applyFor each anchoring point the components fastened to the board ceiling may not exceed the following weights
Fastening method Permissible weight per anchoring point in kgWithout fire resistance With fire resistance
Fastening in the cladding 6 05
Fastening to the grid 10 10
Fastening in the claddingKnauf Hartmut Hohlraumduumlbel cavity dowelScrew M5
Fastening to the gridKnauf Universalschraube FN multi-purpose screw eg curtain rail
The minimum separation spacings between individual attached loads must be observed to avoid local overloading of the ceiling The minimum separation clearance between two attachment points consists of both load radii for the point loadsThe load radius of a point load can be taken from the following diagram in dependence on the permissible weight per unit area for additional loads
Point load in kg
7570656055504540353025201510
0 2 3 4 5 6 7 8 9 10
Radiu
s in c
m
1
50
Fastening in the claddingpossible (without fire resistance)
3 kgmsup2 permissible additional weight (on the exposed ceiling under a fire resistance ceiling refer to the respective valid Knauf system data sheets)6 kgmsup2 permissible additional weight (with fire resistance)15 kgmsup2 permissible additional weight (without fire resistance)
Example fastening scheme at 15 kgmsup2
05 kg
10 kg
3 kgr = 25 cm
r = 46 cm
6 kgr = 355 cm
1 kg
r = 15 cm
r = 105 cm
NoteThe anchored loads can be transferred using several anchoring elements
Loads on board ceilingsFastening in the cladding grid
22
Knauf multi-purpose traversesThe multi-purpose traverse in Knauf board ceilings is suitable for the application of point loads up to 075 kN eg chandeliers music speakers or similarThe multi-purpose traverse consists of a 23 mm thick multi-layer wooden board and galvanized sheet metal profiles It is fastened to the side of the CD furring channelThe attachment of the loads to the traverses should be performed using Knauf Multi-Purpose Screw FNInstallation is possible in a double layer profile grid and flush profile grid
Installation and applicationBend the Daisy chain clip before lateral screw fastening The Daisy chain clip is then Z shaped The unpunched metal side of the Daisy chain clip is pushed onto the lower side of the traverse and then screw fastened laterally through the factory-made hole on the long side of the traverse Screw fasten 4x Daisy chain clips each using one drywall screw TN 35 x 35 about 100 mm from the corner of the multi-layer board on the long edge of the multi-purpose traverse Arrange an additional CD channel (length ge 650 mm) for every long edge in accordance with the width of the multi-purpose traverse Alternately a ceiling furring channel can be used for application of the multi-purpose traverse The supporting profiles are suspended using ceiling suspenders of load class 40 kg The suspenders may not be situated in the direct vicinity of the longitudinal area of the traverse as this will hinder the installation of the traverse Introduce the multi-purpose traverse between the support profiles bend the Daisy chain clip around the CD channel and engage it In case of single-layer cladding do not screw fasten the surface cladding with the multi-purpose traverse
1 Apply the Daisy chain clip 2 Bend the Daisy chain clip 3 Screw fasten the Daisy chain clip
Loads on board ceilingsAnchoring in the traverses
100 mm
23
Loads on board ceilingsAnchoring in the traverses
Scale 110 I Dimensions in mmDetailsD112de SO18 Vertical section ndash Multi-purpose traverse D113de SO12 Vertical section ndash Multi-purpose traverseeg with two additional CD channels I Without fire resistance eg with one additional CD channel I Without fire resistance
D112de SO19 Vertical section ndash Multi-purpose traverse D113de SO13 Vertical section ndash Multi-purpose traverseeg with two additional CD channels I Without fire resistance eg with one additional CD channel I Without fire resistance
D112de SO20 Top view ndash Multi-purpose traverse D113de SO14 Top view ndash Multi-purpose traverseeg with two additional CD channels I Without fire resistance eg with one additional CD channel I Without fire resistance
Fasten Daisy chain clip with drywall screwTN 35 x 35 to multi-purpose traverse
Additional CD channel with two suspendersLoad bearing capacity class ge 040 kN
Multi-purposetraverse555 300 23 mm
300
Furring channel spacing 500
Fasten Daisy chain clip with drywall screwTN 35 x 35 to multi-purpose traverse
Additional suspended load bearing capacity class ge 040 kNMulti-purposetraverse555 300 23 mm
300
Furring channel spacing 500
Additional CD channel with two suspendersLoad bearing capacity class ge 040 kN
Multi-purposetraverse555 300 23 mm
Fasten Daisy chain clip with drywall screwTN 35 x 35 to multi-purpose traverse
Wood panel 555approx
100
Additional suspenderload bearing capacityclass ge 040 kN
Multi-purposetraverse555 300 23 mm
Fasten Daisy chain clip with drywall screwTN 35 x 35 to multi-purpose traverse
Wood panel 555approx
100
Daisy chain clip
Furring channel spacing 500
Traverse
CDchannel
Multi-layerwood panel
Furring channel spacing 500
Multi-purposetraverse
Daisy chain clip
Multi-layerwood panel
Additional grid 4 additional suspension points (eg Nonius suspension)
All technical changes reserved Only the current printed instructions are valid The stated information represents current state-of-the-art Knauf technology The entire state of approved engineering rules appropriate standards guidelines and rules of crafts-manship are not included herewith These and all application instructions have to be adhered to separately by the installer Our warranty is expressly limited to our products in flawless condition All application quantities and delivery amounts are based on empirical data that are not easily transferable to other deviating areasAll rights reserved All amendments reprints and photocopies including those of excerpts require our expressed permission
The stated constructional and structural design specifications and characteristics of building physics of Knauf systems can only be ensured with the exclusive use of Knauf system components or other products expressly recommended by Knauf
Knauf Gips KG Am Bahnhof 7 97346 Iphofen GermanyKnauf DirectTechnical Advisory Service
knauf-direktknaufde
wwwknaufde
VT03deeng09190TI
The iPad App Knauf Infothek now provides all the current information and documents from Knauf Gips KG at any time and in every location in a clear and comfortable wayKnauf Infothek
Videos for Knauf systems and products can be found under the following linkwwwyoutubecomknaufEPD
16
Loads on partitions and furringsFull-length Sanistand
Scale 110DetailsW116de-V1 Sanistand W116de-H1 SanistandVertical section I Without fire resistance Horizontal section I Without fire resistance
UW runnerUniflott + Trenn-Fix
UW runner
Additional UA profile
Sanistand withconcealed mount cistern
Knauf connectionbracket with enclosedM8 carriage bolts
Knauf conection bracket withenclosed M8 carriage bolt
2x 125 mm DiamantDiamant screw XTB
Additional CW stud
Knauf sealing tape
Board strip installationacc to W11de systemdata sheet
Stud spacing le 625 mm
CW stud profile
Additional CW studBoard strip installation in acc with W11de system data sheet
Knauf connection bracket withenclosed M8 carriage bolts
Additional UA profileSanitand with concealedmount cistern
Notes
Max partition height UA 50 = 300 m UA 75 = see system data sheet W11de Knauf Metal Stud Partition for the wall heights
Minimum cladding ge 18 mm Knauf Boards recommendation 2x 125 mm Knauf Diamant
Web cutouts are not permissible in UA Sanistand subject to cantilever loads point loads or linear distributed loadsObserve the manufacturersrsquo details for lateral UA profiles and cladding Additional UA profiles are required laterally on Sanistand mounts acc to DIN 18340 section 374 Only possible without additional UA profiles if the manufacturer of the Sanistand base or WC Sanistand permits itDeviating specifications of the Sanistand manufacturer must be considered and observed
17
Loads on partitions and furringsFull-length Sanistand
Notes
Max partition height rear W112de UA 50 = 300 m UA 75 = see system data sheet W11de Knauf Metal Stud Partition for the wall heights
Minimum cladding front wall installations ge 18 mm Knauf Boards recommendation 2x 125 mm Knauf Diamant
Web cutouts are not permissible in UA Sanistand subject to cantilever loads point loads or linear distributed loadsObserve the manufacturersrsquo details for lateral UA profiles and cladding Additional UA profiles are required laterally on Sanistand mounts acc to DIN 18340 section 374 Only possible without additional UA profiles if the manufacturer of the Sanistand base or WC Sanistand permits itDeviating specifications of the Sanistand manufacturer must be considered and observed
Scale 110DetailsW626Vde-V1 Without back anchoring W626Vde-H1 Without back anchoring Vertical section Horizontal section
UW runnerUniflott + Trenn-Fix
UW runner
Additional UA profile
Sanistand withconcealed mount cistern
Knauf connection bracket withenclosed M8 carriage bolt
Knauf connection bracket withenclosed M8 carriage bolt
2x 125 mm DiamantDiamant screw XTB
Knauf sealing tape
Sanistand withconcealed mount cisternKnauf connection bracket with
enclosed M8 carriage bolts
Stud spacing le 625 mm
UW runner
Knauf boardsCW stud
Additional UA profile
18
Loads on partitions and furringsFull-length Sanistand
Scale 110DetailsW626Vde-V2 Back anchoring in traverse W626Vde-H2 Back anchoring in traverse Vertical section Horizontal section
Sanistand withconcealed mount cistern
SealantUD profile made of insulation strips
UW runner
UW runner
UA profile
Knauf multi-purpose screw FN
Uniflott + Trenn-Fix
Multi-purpose traverse 555 300 23 mm
Knauf connection bracket withenclosed M8 carriage bolts
2x 125 mm DiamantDiamant screw XTB
Knauf connection bracket withenclosed M8 carriage bolt
Wall anchor installation acc to WCSanistand manufacturer specifications
Knauf sealing tape
Stud spacing le 625 mm
Multi-purpose traverse555 300 23 mm
UA profile
UA profile
Knauf connection bracket withenclosed M8 carriage bolt
Knauf connectionbracket with enclosedM8 carriage bolt
Wall anchorinstallation acc to
WC Sanistandmanufacturerspecifications
Notes
Max partition height rear W112de UA 50 = 300 m UA 75 = see system data sheet W11de Knauf Metal Stud Partitions for the wall heights
Minimum cladding front wall installations ge 18 mm Knauf Boards recommendation 2x 125 mm Knauf Diamant
Web cutouts are not permissible in UA Sanistand subject to cantilever loads point loads or linear distributed loadsObserve the manufacturersrsquo details for lateral UA profiles and cladding Additional UA profiles are required laterally on Sanistand mounts acc to DIN 18340 section 374 Only possible without additional UA profiles if the manufacturer of the Sanistand base or WC Sanistand permits itDeviating specifications of the Sanistand manufacturer must be considered and observed
19
Loads on partitions and furringsFull-length Sanistand
Scale 110DetailsW626Vde-V3 Back anchoring in UA profile W626Vde-H3 Back anchoring in UA profile Vertical section Horizontal section
Sanistand withconcealed mount cistern
SealantUD profile on insulation strips
UW runner
UW runner
Additional UA profile
Knauf multi-purpose screw FN
Uniflott + Trenn-Fix
UA profile
Knauf connection bracket withenclosed M8 carriage bolts
2x 125 mm DiamantDiamant screw XTB
Knauf connection bracket withenclosed M8 carriage bolts
Fixing bolts with nuts andwashers
Knauf sealing tape
Stud spacing le 625 mm
Additional UA profile
UA profile Fixing bolts with nutsand washers
Knauf connection bracket withenclosed M8 carriage bolts
Knauf connectionbracket with enclosedM8 carriage bolts
Notes
Max partition height at rear W112de UA 50 = 300 m UA 75 = see system data sheet W11de Knauf Metal Stud Partition for the wall heights
Minimum cladding front wall installations ge 18 mm Knauf Boards recommendation 2x 125 mm Knauf Diamant
Web cutouts are not permissible in UA Sanistand subject to cantilever loads point loads or linear distributed loadsObserve the manufacturersrsquo details for lateral UA profiles and cladding Additional UA profiles are required laterally on Sanistand mounts acc to DIN 18340 section 374 Only possible without additional UA profiles if the manufacturer of the Sanistand base or WC Sanistand permits itDeviating specifications of the Sanistand manufacturer must be considered and observed
20
Loads on partitions and furringsFull-length Sanistand
Scale 110DetailsW626Vde-V4 Back anchoring in mounting rail W626Vde-H4 Back anchoring in mounting rail Vertical section Horizontal section
Sanistand withconcealed mount cistern
2x 125 mm Diamant
SealantUD profile on insulation strips
UW runner
Diamant screw XTB
UA profile
Knauf multi-purpose screw FN
Mounting rail with fixing screw
Knauf connection bracket withenclosed M8 carriage bolt
Uniflott + Trenn-Fix
UA profile
Knauf connection bracket withenclosed M8 carriage bolt
Knauf sealing tapeUW runner
Stud spacing le 625 mm
UA profile
UA profile
Mounting railFixing screw
Mounting screw
Sanistand withconcealed mount cistern
Knauf connection bracket withenclosed M8 carriage bolt
Knauf connectionbracket with enclosedM8 carriage bolt
Notes
Max partition height rear W112de UA 50 = 300 m UA 75 = see system data sheet W11de Knauf Metal Stud Partitions for the wall heights
Minimum cladding front wall installations ge 18 mm Knauf Boards recommendation 2x 125 mm Knauf Diamant
Web cutouts are not permissible in UA Sanistand subject to cantilever loads point loads or linear distributed loadsObserve the manufacturersrsquo details for lateral UA profiles and cladding Additional UA profiles are required laterally on Sanistand mounts acc to DIN 18340 section 374 Only possible without additional UA profiles if the manufacturer of the Sanistand base or WC Sanistand permits itDeviating specifications of the Sanistand manufacturer must be considered and observed
21
Notes
In case of load attachment to ldquomulti-level ceiling systemsrdquo refer to the respective valid Knauf system data sheetsIn case of attachment of loads to free-spanning ceilings see system data sheet D13de Knauf Free-Spanning Ceilings
Attachment of loads to Knauf board ceilingsAdditional loads eg lighting fixtures curtain rails and similar can be fixed to Knauf board ceilings using universal dowels cavity dowels spring toggle dowels or Knauf Hartmut Hohlraumduumlbel cavity dowelsAdditional loads must be considered when determining the load class
NoteHeavy loads must be attached directly on load-bearing building elements (basic ceiling) or on auxiliary constructions eg traverses
For each area under load of the Knauf board ceiling the weight of thefastened components may not exceed the following limits
Permissible weight per ceiling area in kgmsup2Without fire resistance With fire resistance1)
15 61)Incaseofapplicationasafireresistanceceilingwithexposedceiling(multi-levelceilingsystem)15kgmsup2totalweightispermissiblefortheexposedceiling(includinginsulationlayerandattachedloads)attachedtothefireresistanceceiling
Furthermore the following conditions applyFor each anchoring point the components fastened to the board ceiling may not exceed the following weights
Fastening method Permissible weight per anchoring point in kgWithout fire resistance With fire resistance
Fastening in the cladding 6 05
Fastening to the grid 10 10
Fastening in the claddingKnauf Hartmut Hohlraumduumlbel cavity dowelScrew M5
Fastening to the gridKnauf Universalschraube FN multi-purpose screw eg curtain rail
The minimum separation spacings between individual attached loads must be observed to avoid local overloading of the ceiling The minimum separation clearance between two attachment points consists of both load radii for the point loadsThe load radius of a point load can be taken from the following diagram in dependence on the permissible weight per unit area for additional loads
Point load in kg
7570656055504540353025201510
0 2 3 4 5 6 7 8 9 10
Radiu
s in c
m
1
50
Fastening in the claddingpossible (without fire resistance)
3 kgmsup2 permissible additional weight (on the exposed ceiling under a fire resistance ceiling refer to the respective valid Knauf system data sheets)6 kgmsup2 permissible additional weight (with fire resistance)15 kgmsup2 permissible additional weight (without fire resistance)
Example fastening scheme at 15 kgmsup2
05 kg
10 kg
3 kgr = 25 cm
r = 46 cm
6 kgr = 355 cm
1 kg
r = 15 cm
r = 105 cm
NoteThe anchored loads can be transferred using several anchoring elements
Loads on board ceilingsFastening in the cladding grid
22
Knauf multi-purpose traversesThe multi-purpose traverse in Knauf board ceilings is suitable for the application of point loads up to 075 kN eg chandeliers music speakers or similarThe multi-purpose traverse consists of a 23 mm thick multi-layer wooden board and galvanized sheet metal profiles It is fastened to the side of the CD furring channelThe attachment of the loads to the traverses should be performed using Knauf Multi-Purpose Screw FNInstallation is possible in a double layer profile grid and flush profile grid
Installation and applicationBend the Daisy chain clip before lateral screw fastening The Daisy chain clip is then Z shaped The unpunched metal side of the Daisy chain clip is pushed onto the lower side of the traverse and then screw fastened laterally through the factory-made hole on the long side of the traverse Screw fasten 4x Daisy chain clips each using one drywall screw TN 35 x 35 about 100 mm from the corner of the multi-layer board on the long edge of the multi-purpose traverse Arrange an additional CD channel (length ge 650 mm) for every long edge in accordance with the width of the multi-purpose traverse Alternately a ceiling furring channel can be used for application of the multi-purpose traverse The supporting profiles are suspended using ceiling suspenders of load class 40 kg The suspenders may not be situated in the direct vicinity of the longitudinal area of the traverse as this will hinder the installation of the traverse Introduce the multi-purpose traverse between the support profiles bend the Daisy chain clip around the CD channel and engage it In case of single-layer cladding do not screw fasten the surface cladding with the multi-purpose traverse
1 Apply the Daisy chain clip 2 Bend the Daisy chain clip 3 Screw fasten the Daisy chain clip
Loads on board ceilingsAnchoring in the traverses
100 mm
23
Loads on board ceilingsAnchoring in the traverses
Scale 110 I Dimensions in mmDetailsD112de SO18 Vertical section ndash Multi-purpose traverse D113de SO12 Vertical section ndash Multi-purpose traverseeg with two additional CD channels I Without fire resistance eg with one additional CD channel I Without fire resistance
D112de SO19 Vertical section ndash Multi-purpose traverse D113de SO13 Vertical section ndash Multi-purpose traverseeg with two additional CD channels I Without fire resistance eg with one additional CD channel I Without fire resistance
D112de SO20 Top view ndash Multi-purpose traverse D113de SO14 Top view ndash Multi-purpose traverseeg with two additional CD channels I Without fire resistance eg with one additional CD channel I Without fire resistance
Fasten Daisy chain clip with drywall screwTN 35 x 35 to multi-purpose traverse
Additional CD channel with two suspendersLoad bearing capacity class ge 040 kN
Multi-purposetraverse555 300 23 mm
300
Furring channel spacing 500
Fasten Daisy chain clip with drywall screwTN 35 x 35 to multi-purpose traverse
Additional suspended load bearing capacity class ge 040 kNMulti-purposetraverse555 300 23 mm
300
Furring channel spacing 500
Additional CD channel with two suspendersLoad bearing capacity class ge 040 kN
Multi-purposetraverse555 300 23 mm
Fasten Daisy chain clip with drywall screwTN 35 x 35 to multi-purpose traverse
Wood panel 555approx
100
Additional suspenderload bearing capacityclass ge 040 kN
Multi-purposetraverse555 300 23 mm
Fasten Daisy chain clip with drywall screwTN 35 x 35 to multi-purpose traverse
Wood panel 555approx
100
Daisy chain clip
Furring channel spacing 500
Traverse
CDchannel
Multi-layerwood panel
Furring channel spacing 500
Multi-purposetraverse
Daisy chain clip
Multi-layerwood panel
Additional grid 4 additional suspension points (eg Nonius suspension)
All technical changes reserved Only the current printed instructions are valid The stated information represents current state-of-the-art Knauf technology The entire state of approved engineering rules appropriate standards guidelines and rules of crafts-manship are not included herewith These and all application instructions have to be adhered to separately by the installer Our warranty is expressly limited to our products in flawless condition All application quantities and delivery amounts are based on empirical data that are not easily transferable to other deviating areasAll rights reserved All amendments reprints and photocopies including those of excerpts require our expressed permission
The stated constructional and structural design specifications and characteristics of building physics of Knauf systems can only be ensured with the exclusive use of Knauf system components or other products expressly recommended by Knauf
Knauf Gips KG Am Bahnhof 7 97346 Iphofen GermanyKnauf DirectTechnical Advisory Service
knauf-direktknaufde
wwwknaufde
VT03deeng09190TI
The iPad App Knauf Infothek now provides all the current information and documents from Knauf Gips KG at any time and in every location in a clear and comfortable wayKnauf Infothek
Videos for Knauf systems and products can be found under the following linkwwwyoutubecomknaufEPD
17
Loads on partitions and furringsFull-length Sanistand
Notes
Max partition height rear W112de UA 50 = 300 m UA 75 = see system data sheet W11de Knauf Metal Stud Partition for the wall heights
Minimum cladding front wall installations ge 18 mm Knauf Boards recommendation 2x 125 mm Knauf Diamant
Web cutouts are not permissible in UA Sanistand subject to cantilever loads point loads or linear distributed loadsObserve the manufacturersrsquo details for lateral UA profiles and cladding Additional UA profiles are required laterally on Sanistand mounts acc to DIN 18340 section 374 Only possible without additional UA profiles if the manufacturer of the Sanistand base or WC Sanistand permits itDeviating specifications of the Sanistand manufacturer must be considered and observed
Scale 110DetailsW626Vde-V1 Without back anchoring W626Vde-H1 Without back anchoring Vertical section Horizontal section
UW runnerUniflott + Trenn-Fix
UW runner
Additional UA profile
Sanistand withconcealed mount cistern
Knauf connection bracket withenclosed M8 carriage bolt
Knauf connection bracket withenclosed M8 carriage bolt
2x 125 mm DiamantDiamant screw XTB
Knauf sealing tape
Sanistand withconcealed mount cisternKnauf connection bracket with
enclosed M8 carriage bolts
Stud spacing le 625 mm
UW runner
Knauf boardsCW stud
Additional UA profile
18
Loads on partitions and furringsFull-length Sanistand
Scale 110DetailsW626Vde-V2 Back anchoring in traverse W626Vde-H2 Back anchoring in traverse Vertical section Horizontal section
Sanistand withconcealed mount cistern
SealantUD profile made of insulation strips
UW runner
UW runner
UA profile
Knauf multi-purpose screw FN
Uniflott + Trenn-Fix
Multi-purpose traverse 555 300 23 mm
Knauf connection bracket withenclosed M8 carriage bolts
2x 125 mm DiamantDiamant screw XTB
Knauf connection bracket withenclosed M8 carriage bolt
Wall anchor installation acc to WCSanistand manufacturer specifications
Knauf sealing tape
Stud spacing le 625 mm
Multi-purpose traverse555 300 23 mm
UA profile
UA profile
Knauf connection bracket withenclosed M8 carriage bolt
Knauf connectionbracket with enclosedM8 carriage bolt
Wall anchorinstallation acc to
WC Sanistandmanufacturerspecifications
Notes
Max partition height rear W112de UA 50 = 300 m UA 75 = see system data sheet W11de Knauf Metal Stud Partitions for the wall heights
Minimum cladding front wall installations ge 18 mm Knauf Boards recommendation 2x 125 mm Knauf Diamant
Web cutouts are not permissible in UA Sanistand subject to cantilever loads point loads or linear distributed loadsObserve the manufacturersrsquo details for lateral UA profiles and cladding Additional UA profiles are required laterally on Sanistand mounts acc to DIN 18340 section 374 Only possible without additional UA profiles if the manufacturer of the Sanistand base or WC Sanistand permits itDeviating specifications of the Sanistand manufacturer must be considered and observed
19
Loads on partitions and furringsFull-length Sanistand
Scale 110DetailsW626Vde-V3 Back anchoring in UA profile W626Vde-H3 Back anchoring in UA profile Vertical section Horizontal section
Sanistand withconcealed mount cistern
SealantUD profile on insulation strips
UW runner
UW runner
Additional UA profile
Knauf multi-purpose screw FN
Uniflott + Trenn-Fix
UA profile
Knauf connection bracket withenclosed M8 carriage bolts
2x 125 mm DiamantDiamant screw XTB
Knauf connection bracket withenclosed M8 carriage bolts
Fixing bolts with nuts andwashers
Knauf sealing tape
Stud spacing le 625 mm
Additional UA profile
UA profile Fixing bolts with nutsand washers
Knauf connection bracket withenclosed M8 carriage bolts
Knauf connectionbracket with enclosedM8 carriage bolts
Notes
Max partition height at rear W112de UA 50 = 300 m UA 75 = see system data sheet W11de Knauf Metal Stud Partition for the wall heights
Minimum cladding front wall installations ge 18 mm Knauf Boards recommendation 2x 125 mm Knauf Diamant
Web cutouts are not permissible in UA Sanistand subject to cantilever loads point loads or linear distributed loadsObserve the manufacturersrsquo details for lateral UA profiles and cladding Additional UA profiles are required laterally on Sanistand mounts acc to DIN 18340 section 374 Only possible without additional UA profiles if the manufacturer of the Sanistand base or WC Sanistand permits itDeviating specifications of the Sanistand manufacturer must be considered and observed
20
Loads on partitions and furringsFull-length Sanistand
Scale 110DetailsW626Vde-V4 Back anchoring in mounting rail W626Vde-H4 Back anchoring in mounting rail Vertical section Horizontal section
Sanistand withconcealed mount cistern
2x 125 mm Diamant
SealantUD profile on insulation strips
UW runner
Diamant screw XTB
UA profile
Knauf multi-purpose screw FN
Mounting rail with fixing screw
Knauf connection bracket withenclosed M8 carriage bolt
Uniflott + Trenn-Fix
UA profile
Knauf connection bracket withenclosed M8 carriage bolt
Knauf sealing tapeUW runner
Stud spacing le 625 mm
UA profile
UA profile
Mounting railFixing screw
Mounting screw
Sanistand withconcealed mount cistern
Knauf connection bracket withenclosed M8 carriage bolt
Knauf connectionbracket with enclosedM8 carriage bolt
Notes
Max partition height rear W112de UA 50 = 300 m UA 75 = see system data sheet W11de Knauf Metal Stud Partitions for the wall heights
Minimum cladding front wall installations ge 18 mm Knauf Boards recommendation 2x 125 mm Knauf Diamant
Web cutouts are not permissible in UA Sanistand subject to cantilever loads point loads or linear distributed loadsObserve the manufacturersrsquo details for lateral UA profiles and cladding Additional UA profiles are required laterally on Sanistand mounts acc to DIN 18340 section 374 Only possible without additional UA profiles if the manufacturer of the Sanistand base or WC Sanistand permits itDeviating specifications of the Sanistand manufacturer must be considered and observed
21
Notes
In case of load attachment to ldquomulti-level ceiling systemsrdquo refer to the respective valid Knauf system data sheetsIn case of attachment of loads to free-spanning ceilings see system data sheet D13de Knauf Free-Spanning Ceilings
Attachment of loads to Knauf board ceilingsAdditional loads eg lighting fixtures curtain rails and similar can be fixed to Knauf board ceilings using universal dowels cavity dowels spring toggle dowels or Knauf Hartmut Hohlraumduumlbel cavity dowelsAdditional loads must be considered when determining the load class
NoteHeavy loads must be attached directly on load-bearing building elements (basic ceiling) or on auxiliary constructions eg traverses
For each area under load of the Knauf board ceiling the weight of thefastened components may not exceed the following limits
Permissible weight per ceiling area in kgmsup2Without fire resistance With fire resistance1)
15 61)Incaseofapplicationasafireresistanceceilingwithexposedceiling(multi-levelceilingsystem)15kgmsup2totalweightispermissiblefortheexposedceiling(includinginsulationlayerandattachedloads)attachedtothefireresistanceceiling
Furthermore the following conditions applyFor each anchoring point the components fastened to the board ceiling may not exceed the following weights
Fastening method Permissible weight per anchoring point in kgWithout fire resistance With fire resistance
Fastening in the cladding 6 05
Fastening to the grid 10 10
Fastening in the claddingKnauf Hartmut Hohlraumduumlbel cavity dowelScrew M5
Fastening to the gridKnauf Universalschraube FN multi-purpose screw eg curtain rail
The minimum separation spacings between individual attached loads must be observed to avoid local overloading of the ceiling The minimum separation clearance between two attachment points consists of both load radii for the point loadsThe load radius of a point load can be taken from the following diagram in dependence on the permissible weight per unit area for additional loads
Point load in kg
7570656055504540353025201510
0 2 3 4 5 6 7 8 9 10
Radiu
s in c
m
1
50
Fastening in the claddingpossible (without fire resistance)
3 kgmsup2 permissible additional weight (on the exposed ceiling under a fire resistance ceiling refer to the respective valid Knauf system data sheets)6 kgmsup2 permissible additional weight (with fire resistance)15 kgmsup2 permissible additional weight (without fire resistance)
Example fastening scheme at 15 kgmsup2
05 kg
10 kg
3 kgr = 25 cm
r = 46 cm
6 kgr = 355 cm
1 kg
r = 15 cm
r = 105 cm
NoteThe anchored loads can be transferred using several anchoring elements
Loads on board ceilingsFastening in the cladding grid
22
Knauf multi-purpose traversesThe multi-purpose traverse in Knauf board ceilings is suitable for the application of point loads up to 075 kN eg chandeliers music speakers or similarThe multi-purpose traverse consists of a 23 mm thick multi-layer wooden board and galvanized sheet metal profiles It is fastened to the side of the CD furring channelThe attachment of the loads to the traverses should be performed using Knauf Multi-Purpose Screw FNInstallation is possible in a double layer profile grid and flush profile grid
Installation and applicationBend the Daisy chain clip before lateral screw fastening The Daisy chain clip is then Z shaped The unpunched metal side of the Daisy chain clip is pushed onto the lower side of the traverse and then screw fastened laterally through the factory-made hole on the long side of the traverse Screw fasten 4x Daisy chain clips each using one drywall screw TN 35 x 35 about 100 mm from the corner of the multi-layer board on the long edge of the multi-purpose traverse Arrange an additional CD channel (length ge 650 mm) for every long edge in accordance with the width of the multi-purpose traverse Alternately a ceiling furring channel can be used for application of the multi-purpose traverse The supporting profiles are suspended using ceiling suspenders of load class 40 kg The suspenders may not be situated in the direct vicinity of the longitudinal area of the traverse as this will hinder the installation of the traverse Introduce the multi-purpose traverse between the support profiles bend the Daisy chain clip around the CD channel and engage it In case of single-layer cladding do not screw fasten the surface cladding with the multi-purpose traverse
1 Apply the Daisy chain clip 2 Bend the Daisy chain clip 3 Screw fasten the Daisy chain clip
Loads on board ceilingsAnchoring in the traverses
100 mm
23
Loads on board ceilingsAnchoring in the traverses
Scale 110 I Dimensions in mmDetailsD112de SO18 Vertical section ndash Multi-purpose traverse D113de SO12 Vertical section ndash Multi-purpose traverseeg with two additional CD channels I Without fire resistance eg with one additional CD channel I Without fire resistance
D112de SO19 Vertical section ndash Multi-purpose traverse D113de SO13 Vertical section ndash Multi-purpose traverseeg with two additional CD channels I Without fire resistance eg with one additional CD channel I Without fire resistance
D112de SO20 Top view ndash Multi-purpose traverse D113de SO14 Top view ndash Multi-purpose traverseeg with two additional CD channels I Without fire resistance eg with one additional CD channel I Without fire resistance
Fasten Daisy chain clip with drywall screwTN 35 x 35 to multi-purpose traverse
Additional CD channel with two suspendersLoad bearing capacity class ge 040 kN
Multi-purposetraverse555 300 23 mm
300
Furring channel spacing 500
Fasten Daisy chain clip with drywall screwTN 35 x 35 to multi-purpose traverse
Additional suspended load bearing capacity class ge 040 kNMulti-purposetraverse555 300 23 mm
300
Furring channel spacing 500
Additional CD channel with two suspendersLoad bearing capacity class ge 040 kN
Multi-purposetraverse555 300 23 mm
Fasten Daisy chain clip with drywall screwTN 35 x 35 to multi-purpose traverse
Wood panel 555approx
100
Additional suspenderload bearing capacityclass ge 040 kN
Multi-purposetraverse555 300 23 mm
Fasten Daisy chain clip with drywall screwTN 35 x 35 to multi-purpose traverse
Wood panel 555approx
100
Daisy chain clip
Furring channel spacing 500
Traverse
CDchannel
Multi-layerwood panel
Furring channel spacing 500
Multi-purposetraverse
Daisy chain clip
Multi-layerwood panel
Additional grid 4 additional suspension points (eg Nonius suspension)
All technical changes reserved Only the current printed instructions are valid The stated information represents current state-of-the-art Knauf technology The entire state of approved engineering rules appropriate standards guidelines and rules of crafts-manship are not included herewith These and all application instructions have to be adhered to separately by the installer Our warranty is expressly limited to our products in flawless condition All application quantities and delivery amounts are based on empirical data that are not easily transferable to other deviating areasAll rights reserved All amendments reprints and photocopies including those of excerpts require our expressed permission
The stated constructional and structural design specifications and characteristics of building physics of Knauf systems can only be ensured with the exclusive use of Knauf system components or other products expressly recommended by Knauf
Knauf Gips KG Am Bahnhof 7 97346 Iphofen GermanyKnauf DirectTechnical Advisory Service
knauf-direktknaufde
wwwknaufde
VT03deeng09190TI
The iPad App Knauf Infothek now provides all the current information and documents from Knauf Gips KG at any time and in every location in a clear and comfortable wayKnauf Infothek
Videos for Knauf systems and products can be found under the following linkwwwyoutubecomknaufEPD
18
Loads on partitions and furringsFull-length Sanistand
Scale 110DetailsW626Vde-V2 Back anchoring in traverse W626Vde-H2 Back anchoring in traverse Vertical section Horizontal section
Sanistand withconcealed mount cistern
SealantUD profile made of insulation strips
UW runner
UW runner
UA profile
Knauf multi-purpose screw FN
Uniflott + Trenn-Fix
Multi-purpose traverse 555 300 23 mm
Knauf connection bracket withenclosed M8 carriage bolts
2x 125 mm DiamantDiamant screw XTB
Knauf connection bracket withenclosed M8 carriage bolt
Wall anchor installation acc to WCSanistand manufacturer specifications
Knauf sealing tape
Stud spacing le 625 mm
Multi-purpose traverse555 300 23 mm
UA profile
UA profile
Knauf connection bracket withenclosed M8 carriage bolt
Knauf connectionbracket with enclosedM8 carriage bolt
Wall anchorinstallation acc to
WC Sanistandmanufacturerspecifications
Notes
Max partition height rear W112de UA 50 = 300 m UA 75 = see system data sheet W11de Knauf Metal Stud Partitions for the wall heights
Minimum cladding front wall installations ge 18 mm Knauf Boards recommendation 2x 125 mm Knauf Diamant
Web cutouts are not permissible in UA Sanistand subject to cantilever loads point loads or linear distributed loadsObserve the manufacturersrsquo details for lateral UA profiles and cladding Additional UA profiles are required laterally on Sanistand mounts acc to DIN 18340 section 374 Only possible without additional UA profiles if the manufacturer of the Sanistand base or WC Sanistand permits itDeviating specifications of the Sanistand manufacturer must be considered and observed
19
Loads on partitions and furringsFull-length Sanistand
Scale 110DetailsW626Vde-V3 Back anchoring in UA profile W626Vde-H3 Back anchoring in UA profile Vertical section Horizontal section
Sanistand withconcealed mount cistern
SealantUD profile on insulation strips
UW runner
UW runner
Additional UA profile
Knauf multi-purpose screw FN
Uniflott + Trenn-Fix
UA profile
Knauf connection bracket withenclosed M8 carriage bolts
2x 125 mm DiamantDiamant screw XTB
Knauf connection bracket withenclosed M8 carriage bolts
Fixing bolts with nuts andwashers
Knauf sealing tape
Stud spacing le 625 mm
Additional UA profile
UA profile Fixing bolts with nutsand washers
Knauf connection bracket withenclosed M8 carriage bolts
Knauf connectionbracket with enclosedM8 carriage bolts
Notes
Max partition height at rear W112de UA 50 = 300 m UA 75 = see system data sheet W11de Knauf Metal Stud Partition for the wall heights
Minimum cladding front wall installations ge 18 mm Knauf Boards recommendation 2x 125 mm Knauf Diamant
Web cutouts are not permissible in UA Sanistand subject to cantilever loads point loads or linear distributed loadsObserve the manufacturersrsquo details for lateral UA profiles and cladding Additional UA profiles are required laterally on Sanistand mounts acc to DIN 18340 section 374 Only possible without additional UA profiles if the manufacturer of the Sanistand base or WC Sanistand permits itDeviating specifications of the Sanistand manufacturer must be considered and observed
20
Loads on partitions and furringsFull-length Sanistand
Scale 110DetailsW626Vde-V4 Back anchoring in mounting rail W626Vde-H4 Back anchoring in mounting rail Vertical section Horizontal section
Sanistand withconcealed mount cistern
2x 125 mm Diamant
SealantUD profile on insulation strips
UW runner
Diamant screw XTB
UA profile
Knauf multi-purpose screw FN
Mounting rail with fixing screw
Knauf connection bracket withenclosed M8 carriage bolt
Uniflott + Trenn-Fix
UA profile
Knauf connection bracket withenclosed M8 carriage bolt
Knauf sealing tapeUW runner
Stud spacing le 625 mm
UA profile
UA profile
Mounting railFixing screw
Mounting screw
Sanistand withconcealed mount cistern
Knauf connection bracket withenclosed M8 carriage bolt
Knauf connectionbracket with enclosedM8 carriage bolt
Notes
Max partition height rear W112de UA 50 = 300 m UA 75 = see system data sheet W11de Knauf Metal Stud Partitions for the wall heights
Minimum cladding front wall installations ge 18 mm Knauf Boards recommendation 2x 125 mm Knauf Diamant
Web cutouts are not permissible in UA Sanistand subject to cantilever loads point loads or linear distributed loadsObserve the manufacturersrsquo details for lateral UA profiles and cladding Additional UA profiles are required laterally on Sanistand mounts acc to DIN 18340 section 374 Only possible without additional UA profiles if the manufacturer of the Sanistand base or WC Sanistand permits itDeviating specifications of the Sanistand manufacturer must be considered and observed
21
Notes
In case of load attachment to ldquomulti-level ceiling systemsrdquo refer to the respective valid Knauf system data sheetsIn case of attachment of loads to free-spanning ceilings see system data sheet D13de Knauf Free-Spanning Ceilings
Attachment of loads to Knauf board ceilingsAdditional loads eg lighting fixtures curtain rails and similar can be fixed to Knauf board ceilings using universal dowels cavity dowels spring toggle dowels or Knauf Hartmut Hohlraumduumlbel cavity dowelsAdditional loads must be considered when determining the load class
NoteHeavy loads must be attached directly on load-bearing building elements (basic ceiling) or on auxiliary constructions eg traverses
For each area under load of the Knauf board ceiling the weight of thefastened components may not exceed the following limits
Permissible weight per ceiling area in kgmsup2Without fire resistance With fire resistance1)
15 61)Incaseofapplicationasafireresistanceceilingwithexposedceiling(multi-levelceilingsystem)15kgmsup2totalweightispermissiblefortheexposedceiling(includinginsulationlayerandattachedloads)attachedtothefireresistanceceiling
Furthermore the following conditions applyFor each anchoring point the components fastened to the board ceiling may not exceed the following weights
Fastening method Permissible weight per anchoring point in kgWithout fire resistance With fire resistance
Fastening in the cladding 6 05
Fastening to the grid 10 10
Fastening in the claddingKnauf Hartmut Hohlraumduumlbel cavity dowelScrew M5
Fastening to the gridKnauf Universalschraube FN multi-purpose screw eg curtain rail
The minimum separation spacings between individual attached loads must be observed to avoid local overloading of the ceiling The minimum separation clearance between two attachment points consists of both load radii for the point loadsThe load radius of a point load can be taken from the following diagram in dependence on the permissible weight per unit area for additional loads
Point load in kg
7570656055504540353025201510
0 2 3 4 5 6 7 8 9 10
Radiu
s in c
m
1
50
Fastening in the claddingpossible (without fire resistance)
3 kgmsup2 permissible additional weight (on the exposed ceiling under a fire resistance ceiling refer to the respective valid Knauf system data sheets)6 kgmsup2 permissible additional weight (with fire resistance)15 kgmsup2 permissible additional weight (without fire resistance)
Example fastening scheme at 15 kgmsup2
05 kg
10 kg
3 kgr = 25 cm
r = 46 cm
6 kgr = 355 cm
1 kg
r = 15 cm
r = 105 cm
NoteThe anchored loads can be transferred using several anchoring elements
Loads on board ceilingsFastening in the cladding grid
22
Knauf multi-purpose traversesThe multi-purpose traverse in Knauf board ceilings is suitable for the application of point loads up to 075 kN eg chandeliers music speakers or similarThe multi-purpose traverse consists of a 23 mm thick multi-layer wooden board and galvanized sheet metal profiles It is fastened to the side of the CD furring channelThe attachment of the loads to the traverses should be performed using Knauf Multi-Purpose Screw FNInstallation is possible in a double layer profile grid and flush profile grid
Installation and applicationBend the Daisy chain clip before lateral screw fastening The Daisy chain clip is then Z shaped The unpunched metal side of the Daisy chain clip is pushed onto the lower side of the traverse and then screw fastened laterally through the factory-made hole on the long side of the traverse Screw fasten 4x Daisy chain clips each using one drywall screw TN 35 x 35 about 100 mm from the corner of the multi-layer board on the long edge of the multi-purpose traverse Arrange an additional CD channel (length ge 650 mm) for every long edge in accordance with the width of the multi-purpose traverse Alternately a ceiling furring channel can be used for application of the multi-purpose traverse The supporting profiles are suspended using ceiling suspenders of load class 40 kg The suspenders may not be situated in the direct vicinity of the longitudinal area of the traverse as this will hinder the installation of the traverse Introduce the multi-purpose traverse between the support profiles bend the Daisy chain clip around the CD channel and engage it In case of single-layer cladding do not screw fasten the surface cladding with the multi-purpose traverse
1 Apply the Daisy chain clip 2 Bend the Daisy chain clip 3 Screw fasten the Daisy chain clip
Loads on board ceilingsAnchoring in the traverses
100 mm
23
Loads on board ceilingsAnchoring in the traverses
Scale 110 I Dimensions in mmDetailsD112de SO18 Vertical section ndash Multi-purpose traverse D113de SO12 Vertical section ndash Multi-purpose traverseeg with two additional CD channels I Without fire resistance eg with one additional CD channel I Without fire resistance
D112de SO19 Vertical section ndash Multi-purpose traverse D113de SO13 Vertical section ndash Multi-purpose traverseeg with two additional CD channels I Without fire resistance eg with one additional CD channel I Without fire resistance
D112de SO20 Top view ndash Multi-purpose traverse D113de SO14 Top view ndash Multi-purpose traverseeg with two additional CD channels I Without fire resistance eg with one additional CD channel I Without fire resistance
Fasten Daisy chain clip with drywall screwTN 35 x 35 to multi-purpose traverse
Additional CD channel with two suspendersLoad bearing capacity class ge 040 kN
Multi-purposetraverse555 300 23 mm
300
Furring channel spacing 500
Fasten Daisy chain clip with drywall screwTN 35 x 35 to multi-purpose traverse
Additional suspended load bearing capacity class ge 040 kNMulti-purposetraverse555 300 23 mm
300
Furring channel spacing 500
Additional CD channel with two suspendersLoad bearing capacity class ge 040 kN
Multi-purposetraverse555 300 23 mm
Fasten Daisy chain clip with drywall screwTN 35 x 35 to multi-purpose traverse
Wood panel 555approx
100
Additional suspenderload bearing capacityclass ge 040 kN
Multi-purposetraverse555 300 23 mm
Fasten Daisy chain clip with drywall screwTN 35 x 35 to multi-purpose traverse
Wood panel 555approx
100
Daisy chain clip
Furring channel spacing 500
Traverse
CDchannel
Multi-layerwood panel
Furring channel spacing 500
Multi-purposetraverse
Daisy chain clip
Multi-layerwood panel
Additional grid 4 additional suspension points (eg Nonius suspension)
All technical changes reserved Only the current printed instructions are valid The stated information represents current state-of-the-art Knauf technology The entire state of approved engineering rules appropriate standards guidelines and rules of crafts-manship are not included herewith These and all application instructions have to be adhered to separately by the installer Our warranty is expressly limited to our products in flawless condition All application quantities and delivery amounts are based on empirical data that are not easily transferable to other deviating areasAll rights reserved All amendments reprints and photocopies including those of excerpts require our expressed permission
The stated constructional and structural design specifications and characteristics of building physics of Knauf systems can only be ensured with the exclusive use of Knauf system components or other products expressly recommended by Knauf
Knauf Gips KG Am Bahnhof 7 97346 Iphofen GermanyKnauf DirectTechnical Advisory Service
knauf-direktknaufde
wwwknaufde
VT03deeng09190TI
The iPad App Knauf Infothek now provides all the current information and documents from Knauf Gips KG at any time and in every location in a clear and comfortable wayKnauf Infothek
Videos for Knauf systems and products can be found under the following linkwwwyoutubecomknaufEPD
19
Loads on partitions and furringsFull-length Sanistand
Scale 110DetailsW626Vde-V3 Back anchoring in UA profile W626Vde-H3 Back anchoring in UA profile Vertical section Horizontal section
Sanistand withconcealed mount cistern
SealantUD profile on insulation strips
UW runner
UW runner
Additional UA profile
Knauf multi-purpose screw FN
Uniflott + Trenn-Fix
UA profile
Knauf connection bracket withenclosed M8 carriage bolts
2x 125 mm DiamantDiamant screw XTB
Knauf connection bracket withenclosed M8 carriage bolts
Fixing bolts with nuts andwashers
Knauf sealing tape
Stud spacing le 625 mm
Additional UA profile
UA profile Fixing bolts with nutsand washers
Knauf connection bracket withenclosed M8 carriage bolts
Knauf connectionbracket with enclosedM8 carriage bolts
Notes
Max partition height at rear W112de UA 50 = 300 m UA 75 = see system data sheet W11de Knauf Metal Stud Partition for the wall heights
Minimum cladding front wall installations ge 18 mm Knauf Boards recommendation 2x 125 mm Knauf Diamant
Web cutouts are not permissible in UA Sanistand subject to cantilever loads point loads or linear distributed loadsObserve the manufacturersrsquo details for lateral UA profiles and cladding Additional UA profiles are required laterally on Sanistand mounts acc to DIN 18340 section 374 Only possible without additional UA profiles if the manufacturer of the Sanistand base or WC Sanistand permits itDeviating specifications of the Sanistand manufacturer must be considered and observed
20
Loads on partitions and furringsFull-length Sanistand
Scale 110DetailsW626Vde-V4 Back anchoring in mounting rail W626Vde-H4 Back anchoring in mounting rail Vertical section Horizontal section
Sanistand withconcealed mount cistern
2x 125 mm Diamant
SealantUD profile on insulation strips
UW runner
Diamant screw XTB
UA profile
Knauf multi-purpose screw FN
Mounting rail with fixing screw
Knauf connection bracket withenclosed M8 carriage bolt
Uniflott + Trenn-Fix
UA profile
Knauf connection bracket withenclosed M8 carriage bolt
Knauf sealing tapeUW runner
Stud spacing le 625 mm
UA profile
UA profile
Mounting railFixing screw
Mounting screw
Sanistand withconcealed mount cistern
Knauf connection bracket withenclosed M8 carriage bolt
Knauf connectionbracket with enclosedM8 carriage bolt
Notes
Max partition height rear W112de UA 50 = 300 m UA 75 = see system data sheet W11de Knauf Metal Stud Partitions for the wall heights
Minimum cladding front wall installations ge 18 mm Knauf Boards recommendation 2x 125 mm Knauf Diamant
Web cutouts are not permissible in UA Sanistand subject to cantilever loads point loads or linear distributed loadsObserve the manufacturersrsquo details for lateral UA profiles and cladding Additional UA profiles are required laterally on Sanistand mounts acc to DIN 18340 section 374 Only possible without additional UA profiles if the manufacturer of the Sanistand base or WC Sanistand permits itDeviating specifications of the Sanistand manufacturer must be considered and observed
21
Notes
In case of load attachment to ldquomulti-level ceiling systemsrdquo refer to the respective valid Knauf system data sheetsIn case of attachment of loads to free-spanning ceilings see system data sheet D13de Knauf Free-Spanning Ceilings
Attachment of loads to Knauf board ceilingsAdditional loads eg lighting fixtures curtain rails and similar can be fixed to Knauf board ceilings using universal dowels cavity dowels spring toggle dowels or Knauf Hartmut Hohlraumduumlbel cavity dowelsAdditional loads must be considered when determining the load class
NoteHeavy loads must be attached directly on load-bearing building elements (basic ceiling) or on auxiliary constructions eg traverses
For each area under load of the Knauf board ceiling the weight of thefastened components may not exceed the following limits
Permissible weight per ceiling area in kgmsup2Without fire resistance With fire resistance1)
15 61)Incaseofapplicationasafireresistanceceilingwithexposedceiling(multi-levelceilingsystem)15kgmsup2totalweightispermissiblefortheexposedceiling(includinginsulationlayerandattachedloads)attachedtothefireresistanceceiling
Furthermore the following conditions applyFor each anchoring point the components fastened to the board ceiling may not exceed the following weights
Fastening method Permissible weight per anchoring point in kgWithout fire resistance With fire resistance
Fastening in the cladding 6 05
Fastening to the grid 10 10
Fastening in the claddingKnauf Hartmut Hohlraumduumlbel cavity dowelScrew M5
Fastening to the gridKnauf Universalschraube FN multi-purpose screw eg curtain rail
The minimum separation spacings between individual attached loads must be observed to avoid local overloading of the ceiling The minimum separation clearance between two attachment points consists of both load radii for the point loadsThe load radius of a point load can be taken from the following diagram in dependence on the permissible weight per unit area for additional loads
Point load in kg
7570656055504540353025201510
0 2 3 4 5 6 7 8 9 10
Radiu
s in c
m
1
50
Fastening in the claddingpossible (without fire resistance)
3 kgmsup2 permissible additional weight (on the exposed ceiling under a fire resistance ceiling refer to the respective valid Knauf system data sheets)6 kgmsup2 permissible additional weight (with fire resistance)15 kgmsup2 permissible additional weight (without fire resistance)
Example fastening scheme at 15 kgmsup2
05 kg
10 kg
3 kgr = 25 cm
r = 46 cm
6 kgr = 355 cm
1 kg
r = 15 cm
r = 105 cm
NoteThe anchored loads can be transferred using several anchoring elements
Loads on board ceilingsFastening in the cladding grid
22
Knauf multi-purpose traversesThe multi-purpose traverse in Knauf board ceilings is suitable for the application of point loads up to 075 kN eg chandeliers music speakers or similarThe multi-purpose traverse consists of a 23 mm thick multi-layer wooden board and galvanized sheet metal profiles It is fastened to the side of the CD furring channelThe attachment of the loads to the traverses should be performed using Knauf Multi-Purpose Screw FNInstallation is possible in a double layer profile grid and flush profile grid
Installation and applicationBend the Daisy chain clip before lateral screw fastening The Daisy chain clip is then Z shaped The unpunched metal side of the Daisy chain clip is pushed onto the lower side of the traverse and then screw fastened laterally through the factory-made hole on the long side of the traverse Screw fasten 4x Daisy chain clips each using one drywall screw TN 35 x 35 about 100 mm from the corner of the multi-layer board on the long edge of the multi-purpose traverse Arrange an additional CD channel (length ge 650 mm) for every long edge in accordance with the width of the multi-purpose traverse Alternately a ceiling furring channel can be used for application of the multi-purpose traverse The supporting profiles are suspended using ceiling suspenders of load class 40 kg The suspenders may not be situated in the direct vicinity of the longitudinal area of the traverse as this will hinder the installation of the traverse Introduce the multi-purpose traverse between the support profiles bend the Daisy chain clip around the CD channel and engage it In case of single-layer cladding do not screw fasten the surface cladding with the multi-purpose traverse
1 Apply the Daisy chain clip 2 Bend the Daisy chain clip 3 Screw fasten the Daisy chain clip
Loads on board ceilingsAnchoring in the traverses
100 mm
23
Loads on board ceilingsAnchoring in the traverses
Scale 110 I Dimensions in mmDetailsD112de SO18 Vertical section ndash Multi-purpose traverse D113de SO12 Vertical section ndash Multi-purpose traverseeg with two additional CD channels I Without fire resistance eg with one additional CD channel I Without fire resistance
D112de SO19 Vertical section ndash Multi-purpose traverse D113de SO13 Vertical section ndash Multi-purpose traverseeg with two additional CD channels I Without fire resistance eg with one additional CD channel I Without fire resistance
D112de SO20 Top view ndash Multi-purpose traverse D113de SO14 Top view ndash Multi-purpose traverseeg with two additional CD channels I Without fire resistance eg with one additional CD channel I Without fire resistance
Fasten Daisy chain clip with drywall screwTN 35 x 35 to multi-purpose traverse
Additional CD channel with two suspendersLoad bearing capacity class ge 040 kN
Multi-purposetraverse555 300 23 mm
300
Furring channel spacing 500
Fasten Daisy chain clip with drywall screwTN 35 x 35 to multi-purpose traverse
Additional suspended load bearing capacity class ge 040 kNMulti-purposetraverse555 300 23 mm
300
Furring channel spacing 500
Additional CD channel with two suspendersLoad bearing capacity class ge 040 kN
Multi-purposetraverse555 300 23 mm
Fasten Daisy chain clip with drywall screwTN 35 x 35 to multi-purpose traverse
Wood panel 555approx
100
Additional suspenderload bearing capacityclass ge 040 kN
Multi-purposetraverse555 300 23 mm
Fasten Daisy chain clip with drywall screwTN 35 x 35 to multi-purpose traverse
Wood panel 555approx
100
Daisy chain clip
Furring channel spacing 500
Traverse
CDchannel
Multi-layerwood panel
Furring channel spacing 500
Multi-purposetraverse
Daisy chain clip
Multi-layerwood panel
Additional grid 4 additional suspension points (eg Nonius suspension)
All technical changes reserved Only the current printed instructions are valid The stated information represents current state-of-the-art Knauf technology The entire state of approved engineering rules appropriate standards guidelines and rules of crafts-manship are not included herewith These and all application instructions have to be adhered to separately by the installer Our warranty is expressly limited to our products in flawless condition All application quantities and delivery amounts are based on empirical data that are not easily transferable to other deviating areasAll rights reserved All amendments reprints and photocopies including those of excerpts require our expressed permission
The stated constructional and structural design specifications and characteristics of building physics of Knauf systems can only be ensured with the exclusive use of Knauf system components or other products expressly recommended by Knauf
Knauf Gips KG Am Bahnhof 7 97346 Iphofen GermanyKnauf DirectTechnical Advisory Service
knauf-direktknaufde
wwwknaufde
VT03deeng09190TI
The iPad App Knauf Infothek now provides all the current information and documents from Knauf Gips KG at any time and in every location in a clear and comfortable wayKnauf Infothek
Videos for Knauf systems and products can be found under the following linkwwwyoutubecomknaufEPD
20
Loads on partitions and furringsFull-length Sanistand
Scale 110DetailsW626Vde-V4 Back anchoring in mounting rail W626Vde-H4 Back anchoring in mounting rail Vertical section Horizontal section
Sanistand withconcealed mount cistern
2x 125 mm Diamant
SealantUD profile on insulation strips
UW runner
Diamant screw XTB
UA profile
Knauf multi-purpose screw FN
Mounting rail with fixing screw
Knauf connection bracket withenclosed M8 carriage bolt
Uniflott + Trenn-Fix
UA profile
Knauf connection bracket withenclosed M8 carriage bolt
Knauf sealing tapeUW runner
Stud spacing le 625 mm
UA profile
UA profile
Mounting railFixing screw
Mounting screw
Sanistand withconcealed mount cistern
Knauf connection bracket withenclosed M8 carriage bolt
Knauf connectionbracket with enclosedM8 carriage bolt
Notes
Max partition height rear W112de UA 50 = 300 m UA 75 = see system data sheet W11de Knauf Metal Stud Partitions for the wall heights
Minimum cladding front wall installations ge 18 mm Knauf Boards recommendation 2x 125 mm Knauf Diamant
Web cutouts are not permissible in UA Sanistand subject to cantilever loads point loads or linear distributed loadsObserve the manufacturersrsquo details for lateral UA profiles and cladding Additional UA profiles are required laterally on Sanistand mounts acc to DIN 18340 section 374 Only possible without additional UA profiles if the manufacturer of the Sanistand base or WC Sanistand permits itDeviating specifications of the Sanistand manufacturer must be considered and observed
21
Notes
In case of load attachment to ldquomulti-level ceiling systemsrdquo refer to the respective valid Knauf system data sheetsIn case of attachment of loads to free-spanning ceilings see system data sheet D13de Knauf Free-Spanning Ceilings
Attachment of loads to Knauf board ceilingsAdditional loads eg lighting fixtures curtain rails and similar can be fixed to Knauf board ceilings using universal dowels cavity dowels spring toggle dowels or Knauf Hartmut Hohlraumduumlbel cavity dowelsAdditional loads must be considered when determining the load class
NoteHeavy loads must be attached directly on load-bearing building elements (basic ceiling) or on auxiliary constructions eg traverses
For each area under load of the Knauf board ceiling the weight of thefastened components may not exceed the following limits
Permissible weight per ceiling area in kgmsup2Without fire resistance With fire resistance1)
15 61)Incaseofapplicationasafireresistanceceilingwithexposedceiling(multi-levelceilingsystem)15kgmsup2totalweightispermissiblefortheexposedceiling(includinginsulationlayerandattachedloads)attachedtothefireresistanceceiling
Furthermore the following conditions applyFor each anchoring point the components fastened to the board ceiling may not exceed the following weights
Fastening method Permissible weight per anchoring point in kgWithout fire resistance With fire resistance
Fastening in the cladding 6 05
Fastening to the grid 10 10
Fastening in the claddingKnauf Hartmut Hohlraumduumlbel cavity dowelScrew M5
Fastening to the gridKnauf Universalschraube FN multi-purpose screw eg curtain rail
The minimum separation spacings between individual attached loads must be observed to avoid local overloading of the ceiling The minimum separation clearance between two attachment points consists of both load radii for the point loadsThe load radius of a point load can be taken from the following diagram in dependence on the permissible weight per unit area for additional loads
Point load in kg
7570656055504540353025201510
0 2 3 4 5 6 7 8 9 10
Radiu
s in c
m
1
50
Fastening in the claddingpossible (without fire resistance)
3 kgmsup2 permissible additional weight (on the exposed ceiling under a fire resistance ceiling refer to the respective valid Knauf system data sheets)6 kgmsup2 permissible additional weight (with fire resistance)15 kgmsup2 permissible additional weight (without fire resistance)
Example fastening scheme at 15 kgmsup2
05 kg
10 kg
3 kgr = 25 cm
r = 46 cm
6 kgr = 355 cm
1 kg
r = 15 cm
r = 105 cm
NoteThe anchored loads can be transferred using several anchoring elements
Loads on board ceilingsFastening in the cladding grid
22
Knauf multi-purpose traversesThe multi-purpose traverse in Knauf board ceilings is suitable for the application of point loads up to 075 kN eg chandeliers music speakers or similarThe multi-purpose traverse consists of a 23 mm thick multi-layer wooden board and galvanized sheet metal profiles It is fastened to the side of the CD furring channelThe attachment of the loads to the traverses should be performed using Knauf Multi-Purpose Screw FNInstallation is possible in a double layer profile grid and flush profile grid
Installation and applicationBend the Daisy chain clip before lateral screw fastening The Daisy chain clip is then Z shaped The unpunched metal side of the Daisy chain clip is pushed onto the lower side of the traverse and then screw fastened laterally through the factory-made hole on the long side of the traverse Screw fasten 4x Daisy chain clips each using one drywall screw TN 35 x 35 about 100 mm from the corner of the multi-layer board on the long edge of the multi-purpose traverse Arrange an additional CD channel (length ge 650 mm) for every long edge in accordance with the width of the multi-purpose traverse Alternately a ceiling furring channel can be used for application of the multi-purpose traverse The supporting profiles are suspended using ceiling suspenders of load class 40 kg The suspenders may not be situated in the direct vicinity of the longitudinal area of the traverse as this will hinder the installation of the traverse Introduce the multi-purpose traverse between the support profiles bend the Daisy chain clip around the CD channel and engage it In case of single-layer cladding do not screw fasten the surface cladding with the multi-purpose traverse
1 Apply the Daisy chain clip 2 Bend the Daisy chain clip 3 Screw fasten the Daisy chain clip
Loads on board ceilingsAnchoring in the traverses
100 mm
23
Loads on board ceilingsAnchoring in the traverses
Scale 110 I Dimensions in mmDetailsD112de SO18 Vertical section ndash Multi-purpose traverse D113de SO12 Vertical section ndash Multi-purpose traverseeg with two additional CD channels I Without fire resistance eg with one additional CD channel I Without fire resistance
D112de SO19 Vertical section ndash Multi-purpose traverse D113de SO13 Vertical section ndash Multi-purpose traverseeg with two additional CD channels I Without fire resistance eg with one additional CD channel I Without fire resistance
D112de SO20 Top view ndash Multi-purpose traverse D113de SO14 Top view ndash Multi-purpose traverseeg with two additional CD channels I Without fire resistance eg with one additional CD channel I Without fire resistance
Fasten Daisy chain clip with drywall screwTN 35 x 35 to multi-purpose traverse
Additional CD channel with two suspendersLoad bearing capacity class ge 040 kN
Multi-purposetraverse555 300 23 mm
300
Furring channel spacing 500
Fasten Daisy chain clip with drywall screwTN 35 x 35 to multi-purpose traverse
Additional suspended load bearing capacity class ge 040 kNMulti-purposetraverse555 300 23 mm
300
Furring channel spacing 500
Additional CD channel with two suspendersLoad bearing capacity class ge 040 kN
Multi-purposetraverse555 300 23 mm
Fasten Daisy chain clip with drywall screwTN 35 x 35 to multi-purpose traverse
Wood panel 555approx
100
Additional suspenderload bearing capacityclass ge 040 kN
Multi-purposetraverse555 300 23 mm
Fasten Daisy chain clip with drywall screwTN 35 x 35 to multi-purpose traverse
Wood panel 555approx
100
Daisy chain clip
Furring channel spacing 500
Traverse
CDchannel
Multi-layerwood panel
Furring channel spacing 500
Multi-purposetraverse
Daisy chain clip
Multi-layerwood panel
Additional grid 4 additional suspension points (eg Nonius suspension)
All technical changes reserved Only the current printed instructions are valid The stated information represents current state-of-the-art Knauf technology The entire state of approved engineering rules appropriate standards guidelines and rules of crafts-manship are not included herewith These and all application instructions have to be adhered to separately by the installer Our warranty is expressly limited to our products in flawless condition All application quantities and delivery amounts are based on empirical data that are not easily transferable to other deviating areasAll rights reserved All amendments reprints and photocopies including those of excerpts require our expressed permission
The stated constructional and structural design specifications and characteristics of building physics of Knauf systems can only be ensured with the exclusive use of Knauf system components or other products expressly recommended by Knauf
Knauf Gips KG Am Bahnhof 7 97346 Iphofen GermanyKnauf DirectTechnical Advisory Service
knauf-direktknaufde
wwwknaufde
VT03deeng09190TI
The iPad App Knauf Infothek now provides all the current information and documents from Knauf Gips KG at any time and in every location in a clear and comfortable wayKnauf Infothek
Videos for Knauf systems and products can be found under the following linkwwwyoutubecomknaufEPD
21
Notes
In case of load attachment to ldquomulti-level ceiling systemsrdquo refer to the respective valid Knauf system data sheetsIn case of attachment of loads to free-spanning ceilings see system data sheet D13de Knauf Free-Spanning Ceilings
Attachment of loads to Knauf board ceilingsAdditional loads eg lighting fixtures curtain rails and similar can be fixed to Knauf board ceilings using universal dowels cavity dowels spring toggle dowels or Knauf Hartmut Hohlraumduumlbel cavity dowelsAdditional loads must be considered when determining the load class
NoteHeavy loads must be attached directly on load-bearing building elements (basic ceiling) or on auxiliary constructions eg traverses
For each area under load of the Knauf board ceiling the weight of thefastened components may not exceed the following limits
Permissible weight per ceiling area in kgmsup2Without fire resistance With fire resistance1)
15 61)Incaseofapplicationasafireresistanceceilingwithexposedceiling(multi-levelceilingsystem)15kgmsup2totalweightispermissiblefortheexposedceiling(includinginsulationlayerandattachedloads)attachedtothefireresistanceceiling
Furthermore the following conditions applyFor each anchoring point the components fastened to the board ceiling may not exceed the following weights
Fastening method Permissible weight per anchoring point in kgWithout fire resistance With fire resistance
Fastening in the cladding 6 05
Fastening to the grid 10 10
Fastening in the claddingKnauf Hartmut Hohlraumduumlbel cavity dowelScrew M5
Fastening to the gridKnauf Universalschraube FN multi-purpose screw eg curtain rail
The minimum separation spacings between individual attached loads must be observed to avoid local overloading of the ceiling The minimum separation clearance between two attachment points consists of both load radii for the point loadsThe load radius of a point load can be taken from the following diagram in dependence on the permissible weight per unit area for additional loads
Point load in kg
7570656055504540353025201510
0 2 3 4 5 6 7 8 9 10
Radiu
s in c
m
1
50
Fastening in the claddingpossible (without fire resistance)
3 kgmsup2 permissible additional weight (on the exposed ceiling under a fire resistance ceiling refer to the respective valid Knauf system data sheets)6 kgmsup2 permissible additional weight (with fire resistance)15 kgmsup2 permissible additional weight (without fire resistance)
Example fastening scheme at 15 kgmsup2
05 kg
10 kg
3 kgr = 25 cm
r = 46 cm
6 kgr = 355 cm
1 kg
r = 15 cm
r = 105 cm
NoteThe anchored loads can be transferred using several anchoring elements
Loads on board ceilingsFastening in the cladding grid
22
Knauf multi-purpose traversesThe multi-purpose traverse in Knauf board ceilings is suitable for the application of point loads up to 075 kN eg chandeliers music speakers or similarThe multi-purpose traverse consists of a 23 mm thick multi-layer wooden board and galvanized sheet metal profiles It is fastened to the side of the CD furring channelThe attachment of the loads to the traverses should be performed using Knauf Multi-Purpose Screw FNInstallation is possible in a double layer profile grid and flush profile grid
Installation and applicationBend the Daisy chain clip before lateral screw fastening The Daisy chain clip is then Z shaped The unpunched metal side of the Daisy chain clip is pushed onto the lower side of the traverse and then screw fastened laterally through the factory-made hole on the long side of the traverse Screw fasten 4x Daisy chain clips each using one drywall screw TN 35 x 35 about 100 mm from the corner of the multi-layer board on the long edge of the multi-purpose traverse Arrange an additional CD channel (length ge 650 mm) for every long edge in accordance with the width of the multi-purpose traverse Alternately a ceiling furring channel can be used for application of the multi-purpose traverse The supporting profiles are suspended using ceiling suspenders of load class 40 kg The suspenders may not be situated in the direct vicinity of the longitudinal area of the traverse as this will hinder the installation of the traverse Introduce the multi-purpose traverse between the support profiles bend the Daisy chain clip around the CD channel and engage it In case of single-layer cladding do not screw fasten the surface cladding with the multi-purpose traverse
1 Apply the Daisy chain clip 2 Bend the Daisy chain clip 3 Screw fasten the Daisy chain clip
Loads on board ceilingsAnchoring in the traverses
100 mm
23
Loads on board ceilingsAnchoring in the traverses
Scale 110 I Dimensions in mmDetailsD112de SO18 Vertical section ndash Multi-purpose traverse D113de SO12 Vertical section ndash Multi-purpose traverseeg with two additional CD channels I Without fire resistance eg with one additional CD channel I Without fire resistance
D112de SO19 Vertical section ndash Multi-purpose traverse D113de SO13 Vertical section ndash Multi-purpose traverseeg with two additional CD channels I Without fire resistance eg with one additional CD channel I Without fire resistance
D112de SO20 Top view ndash Multi-purpose traverse D113de SO14 Top view ndash Multi-purpose traverseeg with two additional CD channels I Without fire resistance eg with one additional CD channel I Without fire resistance
Fasten Daisy chain clip with drywall screwTN 35 x 35 to multi-purpose traverse
Additional CD channel with two suspendersLoad bearing capacity class ge 040 kN
Multi-purposetraverse555 300 23 mm
300
Furring channel spacing 500
Fasten Daisy chain clip with drywall screwTN 35 x 35 to multi-purpose traverse
Additional suspended load bearing capacity class ge 040 kNMulti-purposetraverse555 300 23 mm
300
Furring channel spacing 500
Additional CD channel with two suspendersLoad bearing capacity class ge 040 kN
Multi-purposetraverse555 300 23 mm
Fasten Daisy chain clip with drywall screwTN 35 x 35 to multi-purpose traverse
Wood panel 555approx
100
Additional suspenderload bearing capacityclass ge 040 kN
Multi-purposetraverse555 300 23 mm
Fasten Daisy chain clip with drywall screwTN 35 x 35 to multi-purpose traverse
Wood panel 555approx
100
Daisy chain clip
Furring channel spacing 500
Traverse
CDchannel
Multi-layerwood panel
Furring channel spacing 500
Multi-purposetraverse
Daisy chain clip
Multi-layerwood panel
Additional grid 4 additional suspension points (eg Nonius suspension)
All technical changes reserved Only the current printed instructions are valid The stated information represents current state-of-the-art Knauf technology The entire state of approved engineering rules appropriate standards guidelines and rules of crafts-manship are not included herewith These and all application instructions have to be adhered to separately by the installer Our warranty is expressly limited to our products in flawless condition All application quantities and delivery amounts are based on empirical data that are not easily transferable to other deviating areasAll rights reserved All amendments reprints and photocopies including those of excerpts require our expressed permission
The stated constructional and structural design specifications and characteristics of building physics of Knauf systems can only be ensured with the exclusive use of Knauf system components or other products expressly recommended by Knauf
Knauf Gips KG Am Bahnhof 7 97346 Iphofen GermanyKnauf DirectTechnical Advisory Service
knauf-direktknaufde
wwwknaufde
VT03deeng09190TI
The iPad App Knauf Infothek now provides all the current information and documents from Knauf Gips KG at any time and in every location in a clear and comfortable wayKnauf Infothek
Videos for Knauf systems and products can be found under the following linkwwwyoutubecomknaufEPD
22
Knauf multi-purpose traversesThe multi-purpose traverse in Knauf board ceilings is suitable for the application of point loads up to 075 kN eg chandeliers music speakers or similarThe multi-purpose traverse consists of a 23 mm thick multi-layer wooden board and galvanized sheet metal profiles It is fastened to the side of the CD furring channelThe attachment of the loads to the traverses should be performed using Knauf Multi-Purpose Screw FNInstallation is possible in a double layer profile grid and flush profile grid
Installation and applicationBend the Daisy chain clip before lateral screw fastening The Daisy chain clip is then Z shaped The unpunched metal side of the Daisy chain clip is pushed onto the lower side of the traverse and then screw fastened laterally through the factory-made hole on the long side of the traverse Screw fasten 4x Daisy chain clips each using one drywall screw TN 35 x 35 about 100 mm from the corner of the multi-layer board on the long edge of the multi-purpose traverse Arrange an additional CD channel (length ge 650 mm) for every long edge in accordance with the width of the multi-purpose traverse Alternately a ceiling furring channel can be used for application of the multi-purpose traverse The supporting profiles are suspended using ceiling suspenders of load class 40 kg The suspenders may not be situated in the direct vicinity of the longitudinal area of the traverse as this will hinder the installation of the traverse Introduce the multi-purpose traverse between the support profiles bend the Daisy chain clip around the CD channel and engage it In case of single-layer cladding do not screw fasten the surface cladding with the multi-purpose traverse
1 Apply the Daisy chain clip 2 Bend the Daisy chain clip 3 Screw fasten the Daisy chain clip
Loads on board ceilingsAnchoring in the traverses
100 mm
23
Loads on board ceilingsAnchoring in the traverses
Scale 110 I Dimensions in mmDetailsD112de SO18 Vertical section ndash Multi-purpose traverse D113de SO12 Vertical section ndash Multi-purpose traverseeg with two additional CD channels I Without fire resistance eg with one additional CD channel I Without fire resistance
D112de SO19 Vertical section ndash Multi-purpose traverse D113de SO13 Vertical section ndash Multi-purpose traverseeg with two additional CD channels I Without fire resistance eg with one additional CD channel I Without fire resistance
D112de SO20 Top view ndash Multi-purpose traverse D113de SO14 Top view ndash Multi-purpose traverseeg with two additional CD channels I Without fire resistance eg with one additional CD channel I Without fire resistance
Fasten Daisy chain clip with drywall screwTN 35 x 35 to multi-purpose traverse
Additional CD channel with two suspendersLoad bearing capacity class ge 040 kN
Multi-purposetraverse555 300 23 mm
300
Furring channel spacing 500
Fasten Daisy chain clip with drywall screwTN 35 x 35 to multi-purpose traverse
Additional suspended load bearing capacity class ge 040 kNMulti-purposetraverse555 300 23 mm
300
Furring channel spacing 500
Additional CD channel with two suspendersLoad bearing capacity class ge 040 kN
Multi-purposetraverse555 300 23 mm
Fasten Daisy chain clip with drywall screwTN 35 x 35 to multi-purpose traverse
Wood panel 555approx
100
Additional suspenderload bearing capacityclass ge 040 kN
Multi-purposetraverse555 300 23 mm
Fasten Daisy chain clip with drywall screwTN 35 x 35 to multi-purpose traverse
Wood panel 555approx
100
Daisy chain clip
Furring channel spacing 500
Traverse
CDchannel
Multi-layerwood panel
Furring channel spacing 500
Multi-purposetraverse
Daisy chain clip
Multi-layerwood panel
Additional grid 4 additional suspension points (eg Nonius suspension)
All technical changes reserved Only the current printed instructions are valid The stated information represents current state-of-the-art Knauf technology The entire state of approved engineering rules appropriate standards guidelines and rules of crafts-manship are not included herewith These and all application instructions have to be adhered to separately by the installer Our warranty is expressly limited to our products in flawless condition All application quantities and delivery amounts are based on empirical data that are not easily transferable to other deviating areasAll rights reserved All amendments reprints and photocopies including those of excerpts require our expressed permission
The stated constructional and structural design specifications and characteristics of building physics of Knauf systems can only be ensured with the exclusive use of Knauf system components or other products expressly recommended by Knauf
Knauf Gips KG Am Bahnhof 7 97346 Iphofen GermanyKnauf DirectTechnical Advisory Service
knauf-direktknaufde
wwwknaufde
VT03deeng09190TI
The iPad App Knauf Infothek now provides all the current information and documents from Knauf Gips KG at any time and in every location in a clear and comfortable wayKnauf Infothek
Videos for Knauf systems and products can be found under the following linkwwwyoutubecomknaufEPD
23
Loads on board ceilingsAnchoring in the traverses
Scale 110 I Dimensions in mmDetailsD112de SO18 Vertical section ndash Multi-purpose traverse D113de SO12 Vertical section ndash Multi-purpose traverseeg with two additional CD channels I Without fire resistance eg with one additional CD channel I Without fire resistance
D112de SO19 Vertical section ndash Multi-purpose traverse D113de SO13 Vertical section ndash Multi-purpose traverseeg with two additional CD channels I Without fire resistance eg with one additional CD channel I Without fire resistance
D112de SO20 Top view ndash Multi-purpose traverse D113de SO14 Top view ndash Multi-purpose traverseeg with two additional CD channels I Without fire resistance eg with one additional CD channel I Without fire resistance
Fasten Daisy chain clip with drywall screwTN 35 x 35 to multi-purpose traverse
Additional CD channel with two suspendersLoad bearing capacity class ge 040 kN
Multi-purposetraverse555 300 23 mm
300
Furring channel spacing 500
Fasten Daisy chain clip with drywall screwTN 35 x 35 to multi-purpose traverse
Additional suspended load bearing capacity class ge 040 kNMulti-purposetraverse555 300 23 mm
300
Furring channel spacing 500
Additional CD channel with two suspendersLoad bearing capacity class ge 040 kN
Multi-purposetraverse555 300 23 mm
Fasten Daisy chain clip with drywall screwTN 35 x 35 to multi-purpose traverse
Wood panel 555approx
100
Additional suspenderload bearing capacityclass ge 040 kN
Multi-purposetraverse555 300 23 mm
Fasten Daisy chain clip with drywall screwTN 35 x 35 to multi-purpose traverse
Wood panel 555approx
100
Daisy chain clip
Furring channel spacing 500
Traverse
CDchannel
Multi-layerwood panel
Furring channel spacing 500
Multi-purposetraverse
Daisy chain clip
Multi-layerwood panel
Additional grid 4 additional suspension points (eg Nonius suspension)
All technical changes reserved Only the current printed instructions are valid The stated information represents current state-of-the-art Knauf technology The entire state of approved engineering rules appropriate standards guidelines and rules of crafts-manship are not included herewith These and all application instructions have to be adhered to separately by the installer Our warranty is expressly limited to our products in flawless condition All application quantities and delivery amounts are based on empirical data that are not easily transferable to other deviating areasAll rights reserved All amendments reprints and photocopies including those of excerpts require our expressed permission
The stated constructional and structural design specifications and characteristics of building physics of Knauf systems can only be ensured with the exclusive use of Knauf system components or other products expressly recommended by Knauf
Knauf Gips KG Am Bahnhof 7 97346 Iphofen GermanyKnauf DirectTechnical Advisory Service
knauf-direktknaufde
wwwknaufde
VT03deeng09190TI
The iPad App Knauf Infothek now provides all the current information and documents from Knauf Gips KG at any time and in every location in a clear and comfortable wayKnauf Infothek
Videos for Knauf systems and products can be found under the following linkwwwyoutubecomknaufEPD
All technical changes reserved Only the current printed instructions are valid The stated information represents current state-of-the-art Knauf technology The entire state of approved engineering rules appropriate standards guidelines and rules of crafts-manship are not included herewith These and all application instructions have to be adhered to separately by the installer Our warranty is expressly limited to our products in flawless condition All application quantities and delivery amounts are based on empirical data that are not easily transferable to other deviating areasAll rights reserved All amendments reprints and photocopies including those of excerpts require our expressed permission
The stated constructional and structural design specifications and characteristics of building physics of Knauf systems can only be ensured with the exclusive use of Knauf system components or other products expressly recommended by Knauf
Knauf Gips KG Am Bahnhof 7 97346 Iphofen GermanyKnauf DirectTechnical Advisory Service
knauf-direktknaufde
wwwknaufde
VT03deeng09190TI
The iPad App Knauf Infothek now provides all the current information and documents from Knauf Gips KG at any time and in every location in a clear and comfortable wayKnauf Infothek
Videos for Knauf systems and products can be found under the following linkwwwyoutubecomknaufEPD
