FANG15B VSC38B-CN 英文版 - Triple S

OWNER’S MANUAL IMPORTANT: READ OWNER’S MANUAL CAREFULLY

MODEL # PANTHER 15B MICRO SCRUBBER

FOR YOUR CONVENIENCE, RECORD THE FOLLOWING

IMPORTANT INFORMATION

MODEL: ___________________________________

SERIAL NUMBER: ____________________________

DATE PURCHASED: ___________________________

PURCHASED FROM: __________________________

29

28

9 -27

8

TABLE OF CONTENTS

1

2-4

4-5

5-6

6

7

Safety Precautions

Machine Set Up & Installation

Machine Operation

Maintenance

Battery Charging

Preventative Maintenance

Techinical Data

Part Breakdown & Lists

Wiring Diagram

Troubleshooting

Avoid moving parts. Do not wear loose

an cause explosion or fire. Do not pick up.

in tanks.

sparks and open flames away! Keep batteryBatteries emit hydrogen gas. Explosion or fi

not intended for any other use. Us

l use. It is constructed for usThis machine is intended for commercia

SAFETY PRECAUTIONSe in an indoor environment and is

e only with recommended accessories.

All operators shall read, understand and exercise the following safety precautions:

1) DO NOT OPERATE MACHINE:Unless trained and authorized.Unless you have read and understand the operators manual.In flammable or explosive areas.

In outdoor areas.

2) BEFORE OPERATING MACHINE:Make sure all safety devices are in place and operate properly.

3) WHEN USING MACHINE:Go slow on inclines and slippery surfaces.Follow all safety guidelines.Be very careful when using the machine in reverse.Report and fix any damage to machine prior to operating it.

4) BEFORE LEAVING OR SERVICING MACHINE:Stop machine on level ground.Turn machine off.

5) WHEN SERVICING MACHINE:Read operators manual thoroughly prior to operating or servicing this machine.Use manufacturer supplied or approved replacement parts.Secure machine with wheel blocks prior to jacking the machine up.Use approved jack or hoist to safely elevate the machine.

Disconnect batteries prior to working on machine.Wear gloves when handling batteries or battery cables.Avoid any contact with battery acid.

fitting clothing while servicing machine.

WARNING！

WARNING！

WARNING！

1

re can result from hydrogen gas. Keep compartment open when charging.

Flammable materials can cause an explosion or fire. Do not use flammable materials

Flammable materials or reactive metals c

If not in proper operating condition.

the squeegee up (33).

Be sure batteries are fully charged (see Battery Charging section).

if equippedif equipped

if equipped

d in figure 2. Pull up the lift lever (26) to raise

1. Turn off the machine.

Brush/Pad Driver Installation and Disassembly

Lower the squeegee (33) with the lift lever (26).

Pre-operation Checks

Charge the batteries (see battery charging section).

WARNING!

7. Brush or pad driver6. Connecting wire for battery and charger 5. Electric Battery Charger Manual

2. Batteries (x2)

MACHINE SET UP & INSTALLATION

BATTERY DISASSEMBLY AND INSTALLATION

2

UNCRATING MACHINE Be sure and check packing carton for any damage. Immediately report any damage to carrier. Check contents of package to ensure that the following items are included: 1. Machine

3. Squeegee assembly4. Scrubber-dryer User Manual

（）

（）

1. Switch off the main switch (47).

2. Remove the recovery tank (2) as shown in the relevant paragraph.

3. Unscrew the bolt from batteries (16), then remove or change.

4. Install the batteries on the machine according to the diagram below.

5. Install the recovery tank.

Do not connect+ to +,or - to-,when disassembly or install the batteries. It is very dangerous.

Battery charging

MACHINE SET UP

1． Sweep or dust mop the surface to be cleaned.

2． Check that squeegee is properly installed.

3．

4．

5． Check that brush/pad is properly installed.

NOTE

2. Lay down the machine in this position as indicate

Only install manually. If auto-installation, it will wear brush hub. Make sure that the tanks are empty before disassembling the brush.

Figure 1

（）

Tighten the knobs securely (unscr

. The brush/pad could disengage and cause injury.

with a pipe or bucket. Do not remove the Solution F ilter (21) while The machine can be filled

Solution Tank F illing

(56/57), unscrew the thumb nut (37).

ew the knobs, if disassembling).

slide the squeegee into the slots of the squeegee

ion as indicated in figure 2.

down the squeegee on the “working” position.

Turn off the main switch (47).

Squeegee Installation

Do not turn on the machine in th position shown beloweWARNING!

locks, as indicated in figure 3.

brackets.

3

3. Mount the brush or pad driver onto the drive wheel hub and then rotate counterclockwise until it

1．

2． Pull down the squeegee lift lever (26) to put

3． Lay down the machine in this posit

4． Loosen the two knobs (55) on the squeegee and

5． To replace the front/rear squeegee

NOTE

Figure 3

Figure 2

hub.4. To remove the brush/pad, rotate the brush/pad clockwise until it is released from drive wheel

filling.

When cleaning excessively aggressive floors this may cause the machine to not work.

ain cap (22) to let water pour out to a

cleaned after each scrubber operation is

and turn the latch (17) to lock the tank. Replace the recovery tank on the machine

he control panel (46).

means the machine is being overloaded. T his indicators on the control panel (46) will flash simultaneously.

rush motor and vacuum B

Before lifting the brush, turn it off by pressing the main switch (47).

Move the machine and start cleaning.

Pull one or both operating triggers (24), and then brush

turning the solution flow control lever (31) manually.

tion switch (50), the indicate light will be on.

Turn on the main switch (47).

pulling down the squeegee lift lever (26).

Set the handle to a comfortable height by pressing handle rotate lever (25).

dirty water into a container, or unscrew the solution tank dr

Turn the latch (17) off the recovery tank, ta

Solution Tank D raining

Clean and rinse the recovery tank

bucket.

Open the lid (1) and overturn the recovery tank to drain the

Recovery Tank D raining Screw on the solution tank drain cap (22).

the solution tank. The solution/water

will flow freely into a bucket or floor drain.

Unscrew the solution tank drain cap (22) on the bottom of

the inlet (20) through pipe or bucket.

build up and clogging of the solution lines.

intended for automatic scrubber applications.

4

Turn on the vacuum motor switch (49), the indicate light will be on.

1. Fill water into solution tank (3) from

2. Do not fill the solution tank completely, leave a few centimeters from the edge.

3. The water temperature must not exceed 40 .

NOTE

1．

2． Rinse the solution tank with clean water after every use. This will help prevent chemical

3．

NOTE

1． ke off the recovery tank from machine by

grasping two grooves of tank.

2． with clean water after every use.

3．

MACHINE OPERATION

1．

2．

3．

4． Turn on the brush motor switch (48) and the solu

5．

6． If necessary, adjust the water flow by

7．

NOTE

.

CAUTION！

CAUTION！

Solution tank should be drained and completed.

Recovery tank should be drained and cleaned after each scrubber operation is completed.

If the battery indicator light (51) is green, the machine can be used. If it is yellow or red, the batteries must be charged.

CAUTION！ Use only low-foam and non-flammable detergents,

Lower the squeegee (33) onto the floor by

will start to spin, solution will begin to flow.

Please turn off all the switches on t

℃

This manual describes the easiest

1. Perform the procedures shown above in

Table, refer to the Service

and most common maintenance

procedures.

arefully read the instruction in the Safety precaution section. charger cable disconnected. C

WARNING!

(After Using the Machine section).

DO NOT USE MACHINE FOR A LONG TIMEthan 30 days, please procee

warranty.

machine prior to storage. Any damage caused by fr

with the brush/pad holder and the squeegee.

tenance section).

1. Remove the brush/pad holder.

2. Empty the tanks as shown in the previous paragraph.

5

CAUTION！ Do not use the machine with discharged batteries to avoid damaging the batteries and reducing the battery

life.

AFTER USING THE MACHINE

After scrubbing, please proceed with below actions before leaving the machine:

3. Perform the daily maintenance procedures (see the main

4. Store the machine in a clean and dry place,

5. If storing in an area which may reach freezing temperatures, be sure to drain all fluids from the

eezing temperatures will not be covered by the

If the machine is not going to be used for more d with below actions:

2. Disconnect the battery connector.

MAINTENANCE The lifespan of the machine and its maximum operating safety are ensured by correct and regular

maintenance. The following chart provides the scheduled maintenance. The intervals shown may

vary according to particular working conditions, which will be defined by the person in charge of the

maintenance.

Maintenance procedures must be performed with the machine switched off and the batteries/battery

All scheduled or extraordinary maintenance procedures must be performed by qualified personnel, or

by an authorized Service Center.

For other maintenance procedures shown in the Scheduled Maintenance Manual that can be consulted at any Service Center.

SCHEDULED MAINTENANCE TABLE

Inlet filter cl

ProcedureAfter each use Weekly Every six

months

Annually

Battery charging

Squeegee cleaning

Brush cleaning

Clean tank, vacuum screen & check top cover

gasket

Squeegee blade check and replacement

eaning

it' s charging, green light means battery charging5. The charging indicator light (30) turns on when

(2). Exposing battery compartment.

1

Keeping the batteries charged makes battery life last longer.

relevant section.

Please use appropriate charger to charge the battery.

Charge the batteries when the yellow or red indicator (51),or at the end of every working cycle

by an authorized Service Center.

After the first 8 working hours.

machine socket.

Connect the charging cable to the he grounded wall outlet (100v~240v).

6. Upon the completion of charging, first unplug

7.

6

This maintenance procedure must be performed

BATTERY CHARGING

NOTE

CAUTION！

CAUTION！！If the machine is not equipped with on-board battery charger, choose an external battery charger

suitable for the type of batteries installed.

WARNING！

1. Place charger and machine in a well ventilated area.

2. Turn machine off (47).

3. Take away the recovery tank

4. Plug the charging cable to t

is completed.

the charging cable from the wall outlet and then

disconnect from machine.

Replace the recovery tank .

NOTE

For further information about the operation of the battery charger (29), see the

.

（）

（2）

Screw and nut tightening check （1）Lubricate rotary parts （1）Check brush motor carbon brushes （2）Check vacuum motor carbon brushes （2）

4. Take off all vacuum kits, gasket, filter, clean and re-install.

(37) to remove the blades.

the vacuum rubber connector (18) between two tanks

as shown in Machine set up section.

BRUSH/PAD DRIVER CLEANING

s. Replace if necessary.

3. Unscrew the thumb nut

are integrity or not.

7

SQUEEGEE CLEANING

NOTE

CAUTION ! It is advisable to wear protective gloves when cleaning the squeegee because there may be sharp debris.

SQUEEGEE BLADE CHECK AND REPLACEMENT

1. Take off the squeegee as shown in the previous paragraph.

5. Install the squeegee in the reverse order of removal.

CAUTION！It is advisable to wear protective gloves when cleaning the brush/pad because there may be sharp debris.

2. Clean and wash the brush/pad with water and detergent.

3. Check the brush bristles for integrity and wearing status; if necessary, replace the brush.

4. Check the pad for wearing status; if necessary, replace the pad driver.

TANK/VACUUM GRID WITH FLOAT CLEANING AND COVER GASKET

CAUTION！

It is advisable to wear protective gloves when cleaning the tank and vacuum/suction assembly because there

may be sharp debris.

1. Move the machine to the appointed disposal area.

2. Turn off the main switch (47).

3. Take off the recovery tank (2), clean and rinse both solution/recovery tank, and drain out.

5. Check the recovery tank lids gasket ring and

NOTE

The gasket ring of recovery tank and the rubber connector between two tanks create vacuum in the tank. If necessary, replace them. .

a good drying performance.The squeegee must be clean and its blades must be in good condition in order to getting

are cracked or split, if necessary replace them with new.2. Check to see if the edge of the front/rear blades

4. Check the front/rear blades for integrity, cut and tear

1. Remove the brush/pad

Sound level 68dBA

Machine length x width x height 770x500x550MM

Control Panel

Vacuum motor data 24V 300W

Input 100-240

Carton spec 780x415x590MM

8

54535251

Vacuum motor switch Brush motor switch Main switch Control panel 46． Electric quantity indicator

47． Brush motor indicator 48． Vacuum motor indicator 49． Suction Electromagnetic valve data indicator 50． Suction Electromagnetic valve data switch

TECHINICAL DATA

Solution tank capacity 15L

Recovery tank capacity 15L

Wheel diameter 254MM

Brush motor data 24V 250W

Electromagnetic valve data 24V

Maximum gradient 2%

Batteries data （2×12V）24V 33Ah/20h

Power cable length /

Batteries spec 196 x 130 x 175mm

Working capacity, up to 800mm

Cleaning productivity 750m2/hour

Squeegee width 490mm

Brush diameter 380mm

Brush rpm 150rpm

Charger Vac,50-60HZ

Output 24Vdc,5A

Machine weight 60kg

Machine weight(with charger and

package) 65kg

．

．．

．

9

PARTS BREAKDOWN

3231

33

375657

30

29

2827

2624

254142

45

4443

40

3938

8

2322

20

21

1819

9

1617

15

14

1312

1110

3

4

7

6

5

2

1

36

22

35

34

59

58

33

10

PARTS BREAKDOWN

Screw nut

Squeegee adjustment piece

Rear squeegee

Front squeegee

Knob

59.

58.

57.

56.

55.

29. Battery Charger

35. Squeegee hose

34. Squeegee wheels

1. Recovery tank lid

2. Recovery tank

3. Solution tank

5. Protective rollers

6. Brush

7. Front handle shell

8. Control panel

9. Rear handle shell

10. Handle rubber

11. Handle iron pipe

12. Squeegee vacuum assembly

13. Squeegee suction assembly

14. Left positioning

15. Right positioning

16. Batteries

17. Latch

18. Rubber sealing

19. Limit hose joint

20. Inlet

21. Solution filter

22. Solution tank drain

23. Wheels on fixed axle

24. Handle left and right

25. Handle rotate lever

26. Squeegee lift lever

27. Squeegee string

28. Box circuit

30. Battery charge indicator

31. Solution flow control lever

32. Electromagnetic valve data

33. Squeegee

36. Axle

37. Thumb nut

38. Vacuum system motor

39. Brush motor

40. Drive belt

41. Belt

42. Squeegee rotation plate

43. Squeegee lift plate

44. Squeegee fixing plate

45. Motor fixing plate

cover4. Brush

54

53

52

51

Vacuum motor switch

Brush motor switch

Main switch

Control panel 46．

Electric quantity indicator

47．

Brush motor indicator

48．

Vacuum motor indicator

49．

Suction Electromagnetic valve data indicator

50． Suction Electromagnetic valve data switch

．

．

．

．

11

76

65

cCOMPLETE ASSEMBLY

47

58

26

42

43

1 6

7

8

9

10

11

12

13

15

16

17

18

19

20

222324 29

30

2

14

14

33

34

35

36

38

39

40

41

45

44

52

32

31

24

5

6

66

21

53

55 565759

54

37

60

25

26

27

28

52

PART LISTPART LISTPART LISTPART LIST

63

62

64

13

15

61

3

4

5

46

48

50 49

12

COMPLETE MACHINE - SSS PANTHER 15B

1PIPE SI, D6XD10, 0.45MVF898461PIPE SI, D4XD8, 0.115MVF89848

PIPE SI, D6XD10, 0.115MVF89847

VF89023US

VF89840

VF89817VF89830

11

VF89821

VF89831

Item Part No. Description Qty

1 VF89100-SSS KIT, SOLUTION TANK 12 VF89018SSS LABEL, SOLUTION TANK 13 VF89200 KIT, AXLE WHEEL 14 VF14251 BOLT, M8X30, HEX HEAD 25 VF13514A WASHER, D8X1XD16.5 56 VF14516 NUT, NYLON INSERT, M8 47 KIT, MOTOR MOUNTING PLATE 18 VF85698 HEX SOCKET SCREW, M8X55 29 VF89030 BUSHING 2

10 VF14258 HEX SOCKET SCREW, M8X40 111 VF14503 NUT, M8 112 VF89400 KIT, SKIRT ASSEMBLY 113 VV13664 WASHER, D4X1XD8 1514 VF13491 PH SCREW, M4X12 1515 KIT, SQUEEGEE 116 VF89029A HOSE, CONNECT SQUEEGEE 117 VF85420 THUMB SCREW 218 KIT, HANDLE ASSEMBLY 119 VF89001 HANDLE BLOCK, LEFT 120 VF89002 HANDLE BLOCK, RIGHT 121 VF89003 CIRCUIT BOX 122 VV60220S1 HEX SOCKET SCREW, M6X15 823 VV20290 WASHER LOCK, ¢6 824 VF13614 WASHER, ¢6 1425 GT13027 PH SCREW, M5X45 126 VA13482 WASHER, D5X1XD10 627 VF89004SSS LATCH, RECOVERY TANK 128 VF89005 SPRING, PRESS 129 KIT, CHARGER 130 VF89025-1 PLATE, MAIN CONTROL 131 VF89006 CIRCUIT COVER 132 VF14301 SCREW, M4X12 2

33VF89034 HEX BOLT M6X50 4

34 VF89052 COVER, WATERPROOF 135 VF89037 PLUG, RUBBER 136 VF89035 COVER NUT, M6 637 VF89016 LABEL, CHARGE DISPLAY 138 VF89012 HANDLE GRIP, RUBBER 239 VF89017SSS LABEL, REAR HOUSING 1

40 VF89007 CABLE, SQUEEGEE LIFT 1

41 VF89008 HANDLE, SQUEEGEE LIFT 142 VV20509 PH SCREW, M5X10 343 VF89010 ROTATE AXLE, SQUEEGEE LIFT CABLE 244 VF89011 AXLE, SQUEEGEE LIFT CABLE 145 VF89009A ROTATE AXLE, SQUEEGEE LIFT CABLE46 VF89056 SOLENOID VALVE, 24V 147 VF14514 NUT, NYLON INSERT, M5 148 VF89033 HOSE495051

BRUSH ASSEMBLY 1PAD DRIVER 152

VF89007-1 CABLE, SQUEEGEE LIFT 1

2

VF89034A HEX BOLT M6X55 2

13

COMPLETE MACHINE - SSS PANTHER 15B

67

65SCREW, M5X12


53 VF85102 SMALL CLAMP 154 VF89055 RUBBER PLUG, CHARGER INSERT 155 VF89020 BATTERY, 2-12V 35Ah 156 VF89036 POWER WIRE 157 VF89021 KIT, BATTERY CONNECT LINE 158 VA13473 PH SCREW, M4X16 559 VF89827 KIT, RECOVERY TANK 160 VF85141 BIG CLAMP 161 VA13472 PH SCREW, M4X86263

VS00001VS00002

11

SUPPORT,LEFTSUPPORT,RIGHT

64 GT13054 2VV13650A SCREW, M4X10 11

66 VF14214 SCREW, M5X8 1VF89015 PLATE 6

14

SOLUTION TANK ASSEMBLY

1

10

1113

14 15

8

9

4

12

18

3

5

6

16

17

2

7

1920 21 22 23


15

VF89100-SSS


1 VF89101SSS SOLUTION TANK 12 VF89102 HOSE, CONNECT VACUUM3 VF89103 SPRING, PRESS 24 VF89104 VACUUM HOSE5 16 VF89106 PLASTIC PLATE, HOSE LIMIT 17 VF89107 RUBBER SEAL 28 VF89115 GASKET 19 VF89110 CAP, DRAIN 1

10 VF85302 RUBBER BUSHING 111 VF89091 SOLUTION TAP 112 VF89112 CABLE BRACKET 113 VF14200 PH SCREW, M6X15 214 VF89113 SEAT, INLET, FRESH WATER TANK 115 VF89114 FILTER, INLET, FRESH WATER TANK 116 VF13491 PH SCREW, M4X12 317 VV13664 WASHER ¢4 318 KIT, SOLUTION TANK 119 VF89201 WHEEL AXLE 120 VF89202 DRIVE WHEEL, 10" 221 VF14563 WASHER,WAVE 222 VF14552 SNAP SPRING 223 VF89202-3 CAP, WHEEL 2

VF89200 KIT, WHEEL AXLE

SOLUTION TANK ASSY - SSS PANTHER 15B

2

2

16

BRUSH DECK ASSEMBLY

15 18

17

25

28

27

26

24

21

20

12

15

23

11

3

22

5

6

7

8

9

10

2

4

19

29

1

30

13

31

16

14

17

33

34

35

36

37

38

32

39

40


42

41

17

VF89823


1 VF89301 PLATE, MOTOR MOUNT 12 VF89302 BRUSH MOTOR ASSEMBLY 13 VF89303 SCREW, M6X14 44 VF89304 BOLT, DIRVE BELT 15 VF89305 O-RING, BIG 16 VF89306 SEALING COVER, VACUUM 17 VF89307 O-RING, SMALL 18 VF89309 KIT, VACUUM MOTOR 19 VF89310 BRACKET, VAC MOTOR 2

10 VF13491 PH SCREW, M4X12 311 VF89311 WASHER, THIN 112 VF89312 PLATE, SQUEEGEE ROTATE 113 VF89313 GUIDE WHEEL, SQUEEGEE 214 VA13482 WASHER ¢5 215 VA13475 PH SCREW, M5X25 316 VF14514 NUT, NYLON INSERT, M5 217 VF89314 KIT, BELT ADJUSTMENT 118 VF14223 SCREW, M6X25 119 VF14506 NUT, NYLON INSERT, M6 420 VF13614 WASHER, ¢6 321 VV20058 BOLT, M6X25, HEX 122 VF89318 SPRING 123 VF89319 BUSHING, SQUEEGEE ROTATE 124 ZD45425 BEARING, 6204 225 VF89320 BUSHING 126 VF89321 DRIVE HUB 127 VF89322 NUT, M20 128 VF89323 DRIVE BELT, PJ270 129 VF89324 PLATE, SQUEEGEE LIFT 130 VF89325 PLATE, SQUEEGEE BRACKET 131 VF89326 ROTATE BOLT, SQUEEGEE LIFT 232 TORSION SPRING 133 VF89315 PLATE, BELT ADJUSTMENT 134 VF89316 BOLT, BEARING 135 VF51126A BEARING, 6201 236 VF89317 WASHER, D12.2XD20X1 337 GT13084 SCREW, M6X20 138 VF89308 SILENCER SPONGE 139 VV13633 NUT, M5 140 VF89337 PRESSURE ADJUSTMENT PLATE 1

BRUSH DECK ASSY - SSS PANTHER 15B

CLAMP DRAIN HOSESCREW, M4X8VV1366742

VF8909241 12

18

BRUSH SKIRT BRUSH

9

6

5

3

4

2

1

7

8

10


&

11

19

VF89817VF89830

HOSEVF8982411

VF89838


1 VF89400 BRUSH SKIRT ASSEMBLY 12 VF89401 BRUSH SKIRT 13 VF89402 WHEEL, BUMPER 24 VF89403 COVER, WHEEL 25 VF89404 SHAFT 26 VF14401 SCREW, ST4X10 6

7VF89051 ELBOW 1

BRUSH ASSEMBLY 1PAD DRIVER ASSEMBLY 1

9 MF-VF002-4A SCREW, ST6.5X25 610 VF89803 BRUSH HUB 1

8

BRUSH SKIRT & BRUSH ASSEMBLY - SSS PANTHER 15B

ELBOW 1

1

20

23

HANDLE CONTROL ASSEMBLY

1

2

4

5

6

7

8

9

10

1112

15

17

1819

20

21

22

16

14133


21

VF89017SSS

VF89839 80405A


1VF89601 HANDLE TUBE ASSY 1

2 KIT, FRONT CONTROL HOUSING 13 PH SCREW, M5X12 44 VF89610 TRIGGER, HANDLE ADJUSTMENT 15 VF89611 CABLE, HANDLE ADJUSTMENT 16 VF89612 BUSHING, GUIDE GEAR 17 VF89613 SPRING, HANDLE GEAR 18 VF89614 GEAR, HANDLE ADJUSTMENT 19 VF89615 TRIGGER, LEFT 1

10 VF89616 TRIGGER, RIGHT 111 VF89617 PIN, HANDLE ADJUSTMENT 112 VF89621 PIN, TRIGGER 213 VF89618 CONTROL HOUSING, REAR 114 VF80407A PH SCREW ,M5X25 815 VF89619SSS LABEL, SWITCH 116 VF89608 CONTROL HOUSING, FRONT 117 33005101 PH SCREW, M3X8 518 VF89622 BOLT, INSULATION, M3X15 519 VV13617 NUT, M3 520 VF40263A SWITCH 121 VF14244 PH SCREW, M3X20 222 VF89025-2 CIRCUIT BOARD 123 LABEL, CONTROL HOUSING 1

HANDLE ASSY - SSS PANTHER 15B

VF89601A HANDLE TUBE ASSY 1

22

RECOVERY TANK ASSEMBLY

1

19

18

17

16

1514

13

12

9

10

11

7

6

54

2 3

24

23

21

20

8

22


23

24


1 VF89701 RECOVERY TANK 12 VF89115 GASKET 13 VF89110 CAP, DRAIN 14 VF89810 RUBBER BUSHING, TANK 15 VF89811 RUBBER BUSHING, TANK, GREY 16 KIT, SQUEEGEE SUCTION 17 VF89829 KIT, SQUEEGEE VACCUM 1

8VF89716 KIT, RECOVERY TANK COVER 1

9 VF89813 BASE, OUTLET 110 VF89712 COVER, RUBBER 111 VA50523 SCREW, ST4X8 412 VF89709 GUIDE BASE, PLUG VACUUM 113 VF89711 PLUG, BASE 114 VF89712 O-RING, PLUG 115 VF89710 PLUG, COVER 116 VF89814 BASE, VACUUM 117 VF89705 O-RING 118 VF89706 COVER, VACUUM 119 VA13477 SCREW, ST4X15 220 SEAL, LID212223

RECOVERY TANK - SSS PANTHER 15B

VF89716A KIT, RECOVERY TANK COVER 1

SCREW, M4X12 6LID, RECOVERY TANK

VF89079

VF89080

11VF89077

VV96001S 1

SEAT,FOR LIDVF89078 SEAL, LID 1

VF89828

24

SQUEEGEE ASSEMBLY

1

2

3

4

5

67

8

9

10

11

12

13

14

15

16

17

18


25

SCREW, M5X3580398A

2

VF8980918

VF89808-PUVF89808

VF89807-PUVF89807VF89815


1 SQUEEGEE BRACKET 1SQUEEGEE BLADE, FRONT 1SQUEEGEE BLADE, FRONT (PU - OPTIONAL) 1SQUEEGEE BLADE, REAR 1SQUEEGEE BLADE, REAR (PU - OPTIONAL) 1

4 VF89504 STRAP, SQUEEGEE FRONT 15 VF89505 STRAP, SQUEEGEE REAR 16 VF89506 WHEEL, SQUEEGEE7 VA13479 BOLT, M6X30, HEX STAINLESS 28 VF89507 BOLT, M6X45, HEX STAINLESS 29 VF14264 BOLT, M6X50, HEX STAINLESS 2

10 VF13614 WASHER, D6.3XD12.6X1.2, STAINLESS 1211 VF89509 NUT, THUMB, M6 612 313 VA13482 WASHER, D5XD10X1.0, STAINLESS 614 VF14514 NUT, NYLON INSERT, M5 315 VF13491 PH SCREW, M4X12 216 VV13664 WASHER, D4XD12X1MM, STAINLESS 217 VF89508 BUSHING 3

2

3

SQUEEGEE ASSY - SSS PANTHER 15B

WHEEL, SQUEEGEE 3

26

ELECTRICAL

This part insert after all assembly1 2

4

5

6

7

3


27


1 VF89026 MOTOR WIRE 12 VF89022 MAIN POWER WIRE 13 VF89021 BATTERY CONNECT WIRE 14 VF89036 POWER WIRE 15 VF89024 CHARGER INPUT WIRE 16 VF89620 KIT, 4-LEG SWITCH 17 VF89025-3 COMMUNICATION WIRE 1

ELECTRICAL PARTS - SSS PANTHER 15B

28

WIRING DIAGRAM

CO NTROLBOARD

KEY-PRESS BOARD

WV

PTC

VACUUMPTC

CBPTC

PRUSHPTC

12AWG RED12AWG BLACK

2#14AWG

RED

2#14AWG

BLACK

1#14AWG

RED

1#14AWG

BLACK

LINKEC3.2

LINKEC3.1

J2 J3

J7.1 J7.2

18AWG

RED

18AWG

BLACK

20AWG WHITE

16AWG BLACK

20AWG WHITE

16AWG RED

SA FETYSW

ITCH

VC C

J5 J4

J11.2

J10.7J10.6

J10.5J10.4J10.3J10.2J10.1

J11.1

J8.3

J9.7J9.6J9.5J9.4J9.3J9.2

J9.1

WATER VALVE VACUUM MOTOR BRUSH MOTOR

MM

LINKEC2.2

LINKEC2.1

WV

GN D

12 AW

GB

LAC

K

J8 .1

COMMUNICATIONLINE

LINKEC1.2

LINKEC1.1

12AWG

RED

CHARGER

-+-

+12V

STORAGEBATTERY

1 2VSTORAGE

BATTERY

12AWG BLACK

29

The recovery tank is not locked Lock the latch (17)

light (51) turns red

light (51) does not turn on

indicator light (52) does not turn on

Solution flow control valve (31) is blocked up Clean the valve

The squeegee leaves marks on the floor

The solution flow is insufficient

The recovery tank is full Empty the recovery tank

threads,etc) preventing the brush from

There are foreign materials (tangled

vacuum motor indicator light (53) does

not turn on

the appropriate position

ust the screw nut(59 )to Adjustment piece(58 )not set at an

appropriate position

jSqueegee ad

TROUBLESHOOTING

The solution is dirty Empty the solution,clean

clean solution. the tank and refill with

The solution is empty Fill the tank

Connect

The power line disconnected from the power Connect

The PCB or key board is faulty Change the PCB or key

The PCB or key board is faulty Change the PCB or key

The suction power is insufficient

Vacuum system motor does not work,

Vacuum system motor does not work,

indicator lights (52) flash

Brush motor does not work, brush

Brush motor does not work, brush

The machine does not work, indicator

The machine does not work, indicator

brush indicator lights (53) flash

Trouble Possible Cause Remedy

The battery connector is disconnected Connect

The batteries are completely discharged Charge the batteries

The batteries are discharged Charge the batteries

board

The deck motor is overloaded Use less aggressive

brushes suitable for the

floor to be cleaned

rotating

Clean the brush hub

board

The vacuum system motor is overloaded Check the vacuum system

motor

The hose is disconnected from the

squeegee

Vacuum assembly is clogged Clean or check

The squeegee is dirty, or the squeegee

blades are worn or damaged

Clean and check the

squeegee

The tank cover is not properly closed, or the

gasket is damaged

Close the cover properly

or replace the gasket

There is debris under the squeegee blades Remove the debris

The squeegee blades are worn, chipped or

torn

Replace the blades

Documents

FANG15B VSC38B-CN 英文版 - Triple S