2004 by Farrier Marine, Inc F-32 Materials Page 1

The following materials will be required for a basic 'sail away boat'. Note that there are many variations possible, withthe different options now available, and different materials and techniques. The amount and type of materials will thusvary with the individual builder. Optional items such as Electronics or Marine Head are not included. For economy,many items such as hatches, can be built by the builder.

BASIC BUILDING MATERIALSSTRONG BACK150 x 25mm /6 x 1" - 29.5m (96') 75 x 25mm/3 x 1" - 15m (50')19mm/3/4" Particleboard/MDF/ply for Form frames19 - 1200 x 2400 (4 x 8') sheets

PRIMARY LAMINATESLaminate options are given on Sheet 1 and the basesheathing and core materials required for hulls,decks etc., can be determined from these, in con-junction with surface areas as listed below.Allow for the following wastage:Cedar 5%, Foam 15%, Glass 15%, Resin10%,

*Main Hull 32.9sq.m. (344sq.ft.)*Main Hull Deck Verticals 21.8sq.m. (235sq.ft.)Main Hull cabin roof (20mm) 10sq.m. (110sq.ft)Aft Cabin Roof (20mm) 2 sq. m. (20 sq.ft)Floats (188sq.ft. per float) 35sq.m. (376sq.ft.)**Struct. Bulkheads (Inc. Floats) 7.8sq.m. (84sq.ft.)Daggerboard case (balsa) 2.9sq.m. (32sq.ft.)*Interior Furniture 15.2sq.m. (164sq.ft.)

FIBERGLASS MATERIALSThe following will be required in addition to basic hulland deck sheathing fabrics as determined above. Ifnecessary, it is permissible to double up fabrics, ie.use two layers of 200gm (6oz) to make one layer of400gm (12oz).

Knytex DBM1208 Tape (or equivalent - see Sheet 1)100mm (4") wide 150m (500') (+3m/10' for 9AX)Can be considerably reduced by using sheathing fabric offcuts150mm (6") wide 33m (109')

Unidirectional tape 400gm/12oz (eg. Knytex A130)100mm (4") wide 92m (301') (+ 3m/10' for 32X)150mm (6") wide 154m (505') (+5m/17' for 32X)

600gm (18oz) B.D. Fabric 40sq.m. (430sq.ft.)400gm (12oz) B.D. Fabric 3.2sq.m.(35sq.ft.)

270gm (8oz) cloth 13sq.m. (140sq.ft.)

200gm/6oz 100mm/4" cloth tape 27m (90')

F-32A, F-32AX AND F-32R MATERIALS LIST

March 21st, 2011

CARBON FIBEROptional in many areas. Min amount for rudder,daggerboard, traveller and chainplates):Uni-dir. 430gm/13oz carbon (eg. Hexcell GA130)150/6" wide - 65 lin.m (214')DB (45-45) 400gm/12oz fabric : 7.4sq.m. (80sq.ft)

RESINApprox. Amount of Resin for Strip Planked boats:200 - 500 litres (55 to 140 gals) (extra 5% for 32AX)(depends on type of fabric - unidirectionals use less resin.Foam core boats will use more resin).

FOAM19mm/3/4" 80/95kg (5 to 6lb) PVC or Urethane foamfor stringers: 2.3sq.m. (25sq.ft.)High Density foam (marine ply optional)12mm (1/2") thick 2.2sq.m. (17 sq.ft.)19/20mm (3/4") thick 2.2sq.m. (8 sq.ft.)(min. density 200kg/12lb, shear strength 3.31MPA or480lbs/sq.in). End grain balsa also optional in some areas.

FOLDING SYSTEMAvailable ready made as per separate Price List.Where possible to be self-made, beams and foldingstrut materials are listed in a separate Plan Book.

STAINLESS STEEL (Type 304 or 316)Minimal amounts of rod, 2 - 6mm plate and sometube, as per Fabricated Parts Book - will depend onoptions and what is purchased ready made.

Aluminum (Type 6061 T6 or 5086 H32)Basic amounts and in various forms (depends onoptions & what is purchased ready made)4-5mm (3/16") plate 850sq.cm (132sq.in)6mm (1/4") plate 2600sq.cm (400sq.in)10mm (3/8") plate 2390sq.cm (370sq.in)12mm (1/2") plate 550sq.cm (85sq.in)12mm (1/2") solid rod 0.5m (20") Mast Raising pole3 x 65mm (1/8 x 2.5") tube 1.83m (6') Mast Raising pole3 x 32mm (1/8 x 1.25") tube 2.4m (8') Aft Mast Support40 x 60 (1.5 x 2.5) al. angle 175mm (7") rudder case60 (2.5") dia Al. rod 165mm (6.5") Mast foot20 x 50 (3/4 x 2") rect bar 300mm (12") Mast foot3 x 50-60mm (2 - 2.5") tube 7.8m (26')(Wing net support - boom section with bolt rope channel is best)

*Increase by 15% (** by 10%) for F-32AX.

2004 by Farrier Marine, Inc F-32 Materials Page 2

EXTERNAL PARTS AND FITTINGSDeck Gear (HK: Harken, RF: Ronstan, SCH: Schaeffer)Preferred choice is always listed first when several partoptions are given

Many catalogues publish recommended sizes for mono-hull yachts. Be aware that a multihull, with its muchgreater stability, will put a higher load on sailing gear.The equivalent monohull size to the F-32 is 12 to 13m (39to 44'). Dont use gear rated for 10m (33') monohulls. Itwill be too small.

Foredeck cleat - 1 or 2200 - 250mm (8 - 10") long. four bolt style.Fasteners to suit with fender washers

Pulpit - 1as per Fabricated Parts BookFasteners to suit

Bow roller to suit bow wing - 1 or 2eg. Sea Dog 328059-1 or to suit anchor style

Hatches 150mm (6") Plastic Screw in type - 7For floats, bow, and safety compartment

Anchor Well Hatch hinges - 2Fasteners to suit

Anchor Well Hatch latch - 1Fasteners to suit

Deck Hatches (Overall size given)Low profile hatches recommendedFloats max. 400 x 530mm (16 x 21") - 2(Moonlight 624532M36)Foredeck max. 560 x 560mm (22 x 22") - 1(Moonlight 625050M36)Aft Cabin 450 x 580mm (18 x 23") - 1Fasteners to suit

Emergency Safety Access Hatch In hull side - 1Low profile, min. 400 x 530mm (16 x 21")Moonlight 62476D (531 dia.circular) recommended.Fasteners to suit

Deck plug for mast lights - 1Mast Step Deckplate - 1(Aluminum Fab. part as per Fab. Parts drg.)

Daggerboard Case Cheekblock - 1Min. Safe Working Load 500kg / 1100lbseg RF51151, SCH505-11Plus one mounting plate (as per Fab. parts drg.)Fasteners to suit

Daggerboard Sheave/exit blocks - 2Min. SWL 180kg / 400lbRonstan RF460 or use two HK 289Plus mountng plate as per Fab. Parts Drg.Fasteners to suit

Daggerboard Double Organizer - 1Min. SWL 180kg / 400lbRF450, SCH504-80, HK1500Fasteners to suit

Daggerboard Deck exit block - 2Harken 089Fasteners to suit

Daggerboard Clamcleat - 1CL201 or CL 219Fasteners to suit

D/board Upline 9/10mm x 5.3m /3/8" x 17' red - 1D/board downline 9/10mm x 7m / 3/8 x 23' blue - 1

Deck Organizers, double Sheave - 2Min.working load 600kg (1300lb) per sheaveHarken 6052, Spinlock T50/2, Lewmar 29139102,Must have min. 8mm/5/16" fasteners (6mm willbend)

Jib Sheet tracks 600mm (2') long T track - 2Harken 32mm track HK1891.1.2 (cut in half)8mm Fasteners to suit

Jib Sheet leads - 2Min. Wk. Load 1000kg (2200lbs).Harken B1875AM or HK 1997

Mast Raising Loops - 2For mast raising system as per Fab. Parts Bookwith RF1057 saddle eyes (with ferrule) - 4Fasteners to suit.8mm bore by 12mm O.D. flanged plastic bush, 9 -12mm long,eg Ceelon/AE S48M, or Iglide MFM 0812-128mm Nylock nut & 8mm washers - 8

Rope clutches (for main & Jib) - 2Spinlock XCSFasteners to suit.

Rotator Pad Eye - 1Wichard 6 584, RF416 or SCH 78.05Fasteners to suit

Stand Up Reefing Line Blocks - 2HK 1573 base - 2HK 1950 or 1540 Block - 2Fasteners to suit

2004 by Farrier Marine, Inc F-32 Materials Page 3

Halyard winch (Andersen 40ST ) - 1Fasteners to suit

Sheet Winches (Andersen 40 - 46 ) - 2Fasteners to suit

Camcleats for Jib sheets - 2Harken 150 with HK 145 angled spacersFasteners to suit

Mainsheet Traveler SystemMin. working Load 1200kg (2600lbs)Harken 3154 track 1.5 - 2.4m long, fasteners to suitHarken 3163 (plus 1799s) or 3176 cars -1Harken 3170 control blocks - 28/9 mm control line - one at 13.4m (44') long

Aft deck cleats 200mm (8") long- 2Fasteners to suit with fender washers

Pushpit - as required depending on modelFasteners to suit

Wingnets - 2(as per Fab Parts drg.)6mm (1/4") black line - approx. 40m / 130'

Bow nets - 2(as per Fab Parts drg.)6mm (1/4") black line - approx. 25m / 82'

Bow Net Support Wires - Two at 3.5m (11' 6")6mm synthetic line (eg Vectran/spectra) with lashing.

Bow Net line/wire Beam Anchors - 26mm/1/4" U-bolts or saddle eyesWichard 65432, RF559, or RF1056)

Water fill deck fitting - 1Watertank Vent - 1

Compass - 1

Rudder and Tiller Assembly - as per Drawings

Bow Nav. Light - 1Stern Nav. Light - 1

Deck Vents - as required

FLOAT ITEMS:Pad eyes (for Barber Haulers) - 46mm/1/4" boltsWichard 6 504, RF44 - Two extra optional for floatbows for general use and lifeline anchorsFasteners to suit

Saddle eyes (for float bow eyes) - 2Four 8mm (5/16") PH machine screwsRF528, SCH78-37

DECK OPTIONS:JIB FURLERHarken 061 mount base for pulpit - 1Harken 166 lead block - 1Harken 429 standup lead for bow - 1

Deadeyes - 3RF59, SCH78-51 plus Fasteners to suit

Camcleat - 1Harken 150 with HK375 fairleadFasteners to suit

SCREACHER

Halyard Rope Clutch - 1Spinlock XTS or XCS

Sheet tracks 600mm (2') long T track - 2RF706 or HK 2751 track plus fasteners to suit.

Screacher Sheet leads - 2Min. Wk. Load 600kg (1300lbs).RF874 or HK2750 with HK2660, 370 (2), & 2722 (4)Note that above Harken track and slide are border-line for screacher, and no guarantee is given.Alternative is HK 704 with 759 track, but is overkill

Screacher Sheet Block Mounting Plates - 2As per Fabricated Parts Book- Fasteners to suit

Screacher Furling Line LeadsHarken 061 mount base for pulpit - 1Harken 166 lead block - 1Deadeyes for furling line - 3RF59, SCH78-51 plus fasteners to suit

Camcleat - 1Harken 150 with HK375 fairlead

SPINN. OR SCREACHER WINCHES - 2Andersen 40 (46 optional for F-32R)Fasteners to suit

SPINNAKER

Halyard Rope Clutch - 1Spinlock XTS or XCS

Tack Line Clutch - 1Spinlock XTS or XCS

2004 by Farrier Marine, Inc F-32 Materials Page 4

Deadeyes - 2RF59, SCH78-51Fasteners to suit

Camcleats - 2Harken 150 with HK 145 angled spacerFasteners to suit

Spinn. Sheet Block Mounting Plates - 2As per Fabricated Parts BookFasteners to suit

BARBER HAULERS

Deadeyes - 2RF59, SCH78-51Fasteners to suit

Camcleats - 2Harken 150Fasteners to suit - 4

Ventilation hatch in Fwd. Head Compartment - 1Max. size 280 x 280 (located in hull side)

Ventilation hatch in deck over foward galley - 1Max. size 310 x 310

INTERIOR PARTSStove unit - 1

Galley sink (Stainless Steel ) - 1Water hand pump (galley) - 1Drain/waste Fitting - 1Thru/hull to match - 1Hose clamps - 2Hose 500 (20") long - 1Galley Formica - 1

Vanity Unit (Optional)Vanity Sink - 1Hand water pump - 1White lined small bore water hose - Measure to suitDrain/waste Fitting - 1Drain thru hull - 1Hose clamps - 5Drain Hose - 125mm nylon Clamps for hose - 2

Water Tank - 100 - 130L (25 - 34 gallons) - 140mm / 1 1/2" fill fitting - 112 - 16mm / 1/2" - 5/8" outletWhite lined small bore water hose -measure to suitLarge bore Water Fill hose - measure to suitHose MUST be correct type for drinking waterSmall hose clamps - 4, Large hose clamps - 2

Hatches 150mm (6") plastic screw-in as requiredfor bunk/watertight compartment inspectionFasteners to suit

Fwd. Passageway Curtain & track - 1

Interior cushions as required

INTERIOR OPTIONSHeadLavac Vacuum head recommended

ELECTRICALThe following items will be required for basic wiringsystem as shown by wiring diagram.

Battery (Only use Marine Type sealed Battery) - 1Must not leak when inverted

Battery hold down strap and clips (2) - 1Fasteners to suit

Electrical Switch panel - 1

Battery Check Voltmeter - 1

Battery Master switch - 1

Main Cabin lightGalley LightFwd. Cabin lightHead LightAft Cabin light

Wire Approx. lengths:6g Red 8.5m (28') for O/b electric start6g Black 8.5m (28') for O/b electric start8g Red 3m (10')8g Black 3m (10')14g Black 4m (13')16g Assorted colors 60m (196')16g Twin jacketed wire 20m (70')

Connectors6g H/duty Ring Connectors, - 48g Ring Connectors - 416g assorted connectors - 32

Terminal Blocks - as requiredAssorted wire ties - 20Screw on wire ties - 40

2004 by Farrier Marine, Inc F-32 Materials Page 5

MAST, RIG AND SAILSMast Section as per Mast Plan

Mast Foot as per Fab. Parts drg. - 160 x 16 x 10mm bore Delrin Sheaves - 4(2 3/8" x 5/8" x 3/8") (approx size)9mm x 65mm (3/8" x 2 5/8") Clevis pins - 2

Main halyard - 46m (151') long (for 2 : 1 halyard).Min. breaking strain 1800kg (4000lb). 8 - 9mm (5/16- 3/8") HT synthetic line recommended with head-board shackle. 6mm line optional, with some highperformance synthetics, but can be hard to handle.

Jib halyard - 26.5m long (87')Min. breaking strain 1800kg (4000lb). 8 - 9mm (5/16- 3/8") HT synthetic line recommended withsnapshackle. 6mm line also opt. as above.

Screacher halyard - 41.5m long (136') for 2 : 1halyard. Min. break. strain 900kg (2000lb)6 - 8mm (1/4 - 5/16") synthetic line recommendedwith snapshackle. Use a min. breaking strain 1800kg(4000lb) line if 1 : 1 halyard is used

Spinnaker halyard - 32.5m (107') long8 - 9mm (5/16 - 3/8") red line with snap shackle

Standing rigging - synthetic line with Precourtdeadeys as per Mast and Rigging Drawing. Min req.breaking strain of 7500kg (16,500lbs). Total lengthrequired is approx. 36.8m (121')

Beam/Float Diagonal Braces - 4 at approx. 4.3m(14' 3") long (inc. turnbuckle) - see Sht. 34. Can be4.5mm (3/16") 7 x 19 s.s. plastic covered wire or lowstretch synthetic line is optional.

Gooseneck Fixed commercial unit or roller furling

Topping lift (if required - Lazy jacks can be used)6mm x 13m (1/4" x 42.5') black rope - 16mm x 14.9m (1/4" x 49') black rope - 1Small single block (RF185/SCH02-03) - 1S.S. snap hook - 1

Boom SectionAs per Boom drawing, with all outhaul/reefingclutches on/in boomSpinlock XTS clutches for reefing lines.

SAILSMainsail (full battened)JibScreacher (Optional)Storm Jib (Optional)Spinnaker (Optional)

BASIC SAILING EQUIPMENTMAINSHEET AssemblyMin. Safe Working Load of 800kg/1800lbsTwo speed 6 : 1 and 24 : 1 system recommendedHK 1546, HK 1555, HK 2642, HK 2658, HK 282 eye9/10mm (3/8") line 24m (aft cabin) 21m (aft Cockpit)6mm (1/4") line - 2.5m

JIB SHEET - 15m (50') long8 to 10mm (5/16 to 7/16") lineWith suitable clew shackle or line loop.

ROTATOR CONTROLMin. SWL 200kg/440lbHK 2642 and HK 26588 to 10mm (5/16 to 7/16") line, 2.7m (9')

Winch handles (2)

OPTIONSJib Furler - Harken Unit 1Furler line if not included with furler,

Barber Haulers - 8m (26') long - 28 - 9mm (5/16 to 3/8") lineS hooks (RF48A or SCH76-44) - 2 (or small blocks)Blocks RF50100 with RF6170 or SCH505-09 - (2)

Cunningham Eye tackleFiddle block (Harken 053 ) PLUS shackle to suitFiddle block with cleat (H058 )6mm x 2m / 1/4" black line - 1.8m (6')9mm x 6m / 3/8" red line - 6m (19')

SCREACHER

Furler - Harken 1900 or Facnor SDG200PCFurling Line - 8mm line 20m (65') long

Screacher Sheet blocks - 2Min breaking load 1000kg (2200lbs)HK 1958 , RF858, or SCH09-09 -UCScreacher Sheets 8 - 10mm line, 16m (53') long - 2

2004 by Farrier Marine, Inc F-32 Materials Page 6

ASYMMETRIC SPINNAKER

Carbon Bow Pole and Bobstay as per Drawing

Spinnaker sheets 18m (60') long - 28 - 10mm lineTack Line (different color) 15.5m (51') long - 18 - 10mm line,

Spinn. Sheet blocks - 2Min breaking load 1000kg (2200lbs)HK 1958 , RF858, or SCH09-09 -UC

Spinn. Tack Block - 1Min breaking load 1000kg (2200lbs)HK 1958, RF868, SCH09-05Snap shackles for sheets and tack line - 3

MISCELLANEOUSBeam bolt speed wrenchSocket (to suit beam bolts)

Velcro straps for rigging ties - 6

Mast raising pole as per Parts drg - 1

Aft Mast Support as per Parts drg - 1

TOOLKIT - with the following:Adjustable wrench (250mm / 10")200mm / 8" Channel locksPhillips screwdriverSlotted screwdriverSpare beam bolt wrenchTwo spare Beam BoltsRigging knifeSpare Clevis pins (2)Spare 4mm / 3/16" shackleSpare 6mm / 1/4" shackleSpare 9mm / 3/8" shackleSpare lock rings for turnbuckles if usedSpare 6mm / 1/4" black line x 2m / 6' long

DOCKING GearDock lines - 9mm x 10m / 3/8 x 33' - 4Fenders - 3

SAFETY GEAR

Anchor (Fortress FX16 recommended) - 1(min. required - check with local regs.)8mm (5/16") chain - 5m (1 6')13mm x 60m (1/2" x 200') nylon anchor line8mm (5/16") Galv. shackles - 2

Flare kitBilge PumpAnchor light and batteryFlashlight & batteryFirst Aid kitFire Extinguishers 2Fire extinguisher brackets - 2Life buoy and holder

Stanchions and LifelinesMin. 6 stanchions and bases, height as required.Stanchions must be removable for trailering.

OUTBOARD 6 to 15 Kw (8 to 20HP)Mounting BracketRemote Controls to suit

TRAILER as per Trailer drawing