Upload
others
View
6
Download
0
Embed Size (px)
Citation preview
1
IMPORTANT:
Go to www.extron.com for the complete
user guide, installation instructions, and
specifications before connecting the
product to the power source.
DTP T EU 4K and DTP T MK 4K • Setup GuideThis guide provides instructions for a professional installer to install any of the Extron DTP T EU 4K 331, DTP T EU 4K 231, DTP T MK 4K 331, or DTP T MK 4K 231 transmitters into an EU or MK one-gang junction box or European cable channel system and to make all connections.
The HDMI transmitters, paired with a compatible receiver, can extend the digital video signal up to 330 feet (100 meters) (DTP T EU 4K 331 and DTP T MK 4K 331) or 230 feet (70 meters) (DTP T EU 4K 231 or DTP T MK 4K 231).
Top
Side RearFront
HD
BT
DT
P
HDMI IN0.7 A MAX
POWER12V
C
D
B
AC B
Figure 1. DTP T EU 4K and DTP T MK 4K Unit Features
Installation
Planning
CAUTION: Failure to check these items may result in personal injury or property damage.
ATTENTION : La non-vérification des éléments listés ci-dessous peut provoquer des blessures ou dommages matériels.
� Check that the installation meets the building, electrical, and safety codes. � Ensure there is enough space in the junction box or Euro channel for the DTP transmitter, cables, and rear panel connectors when the DTP transmitter is completely connected and mounted.
NOTE: The transmitters require 47 mm (1.9”) in the junction box for the device plus cable clearance.
Mounting and CablingFor additional mounting details and considerations, see the DTP T EU 4K 331, DTP T MK 4K 331, DTP T EU 4K 231, and DTP T MK 4K 231 User Guide at www.extron.com).
Step 1 — Install the junction box or Euro channelInstall the appropriate junction box or Euro channel according to the requirements of the manufacturer (see the manufacturer specifications for more details). This may require creating an opening in the mounting surface. If so, consider the following:
• For accuracy, use the mounting enclosure to mark cut guidelines.
• To avoid making an opening too big, cut inside the marked guidelines.
Rear and Side Panel Features (Set switch and make connections before mounting)
Front Panel Features(Make connections after mounting)
A TP function switch (see page 2)B TP outputC DC power input
D HDMI input (see page 3)
2
DTP T EU 4K and DTP T MK 4K • Setup Guide (Continued)
Step 2 — Set the TP function switch and make rear and connections
A TP function switch (see figure 1 on the previous page) — DTP
HDBT
If the receiving device is in the Extron DTP series, set this switch to DTP. The TP output consists of HDMI with embedded audio, analog audio, RS-232 and IR, and remote power over the twisted pair (TP) cable from the receiver.
For an HDBaseT-enabled receiver, set this switch to HDBT position. The TP output consists of HDMI with embedded audio plus RS-232 and IR. The transmitter and receiver each requires its own 12 VDC power supply.
ATTENTION:• Position this switch BEFORE connecting the appropriate device to the TP connector. Failure to comply can damage the
endpoint.
• Positionnez le sélecteur AVANT de connecter l’appareil approprié au connecteur TP. Ne pas respecter cette procédure pourrait endommager le point de connexion.
B TP Output port — Connect the Out (RJ-45) port to the DTP In port on the receiver. Extron recommends that you terminate both cable ends in accordance with the following, at a minimum: TIA/EIA T 568B and 24 AWG, solid conductor, shielded cable with 400 MHz bandwidth.
ATTENTION:• Do not connect this connector to a computer data or telecommunications network.
• Ne connectez pas ces port à des données informatiques ou à un réseau de télécommunications.
Signal (green) LED — Lights when the device is transmitting a video signal or a test pattern.
Link (yellow) LED — Lights when a valid link between a DTP or HDBT input and output is established.
C Power — When the TP function switch is in the DTP position, this connector is probably not necessary. The connected
0.7 A MAX
POWER12V
receiving device can power the transmitter via the TP cable.
If the TP function switch (see figure 1, on the previous page and A, above) is in the HDBT position, or if otherwise desired, plug an optional external 12 VDC power supply into this 2-pole direct insertion connector. See the DTP T EU 4K 331, DTP T MK 4K 331, DTP T EU 4K 231, and DTP T MK 4K 231 User Guide, available at www.extron.com, for wiring instructions and important safety considerations.
Step 3 — Install the transmitter to a junction box
ATTENTION:• Ensure that the junction box is grounded properly.
• Assurez vous que le boîtier d’encastrement est correctement mis à la terre.
NOTE: Removal of the module is difficult after the module has been installed in the bezel frame. Ensure that all connections are correct BEFORE snapping the module in place.
Mount the transmitter to a junction box as follows:
a. Disconnect power from all devices at the source.
b. Orient the mounting bracket as appropriate for your transmitter (see figure 2, at right):
MK mounting — The word “Front” engraved on the bracket reads vertically.
EU mounting — “Front” reads horizontally.
c. Fasten the provided metal mounting bracket to the mounted junction box, in the proper orientation, using the two included screws.
NOTES:• To keep the transmitter securely in place and prevent it from being easily pulled
from its mounting surface, ensure that the side of the bracket with the word “Front” engraved on it faces out (away from the junction box).
• If you want to be able to remove the transmitter easily from its mounting, attach the mounting bracket with “Front” facing inward, toward the junction box.
d. Run the TP cable and optional power cable through the junction box and the plastic bezel frame.
e. Set the TP function switch (A) to the appropriate position.
f. Connect the rear panel cables to the transmitter.Figure 2. Installation
EU Mounting Bracket
EU Wall Box
Bezel Frame
DTP T EU
MK Mounting Bracket
EU Mounting
MK Mounting
MK Wall Box
B l Frame
3
g. Align the bezel frame to the metal mounting bracket on the mounting surface.
h. Holding the bezel frame in place on the bracket, press the transmitter into the frame until the unit snaps into place and all four tabs on the unit snap into their slots.
Step 4 — Make front panel (input) connection
D HDMI input port (see figure 1 on page 1) — Connect an HDMI cable between this port and the HDMI output port of the HDMI IN digital video source.
OperationAfter all connected devices are connected and powered on, the system is fully operational. If any issues arise, verify that the cables are routed and connected properly and that the display device has a compatible resolution and refresh rate. If problems persist, call the Extron S3 Sales & Technical Support Hotline. See the contact numbers on the last page of this guide for the Extron office nearest you.
Application Diagram
L R
POWER12V 0.7A MAX
AUDIO
SIG LINK
DTP IN
OUTPUTS
L R
POWER12V 0.7A MAX
AUDIO
SIG LINK
DTP IN
OUTPUTS
DTP HDMI 330 Rx
OVER DTP
RS-232 IR
Tx Rx Tx RxGDTP HDMI 330 Rx
OVER DTP
RS-232 IR
Tx Rx Tx RxG
50-60 Hz
100-240V ~ -- A MAX
SIG LINK
OUT
1
1 2 3 4 5 6
2 3A 4A 4B 4
RS-232 IR
RS-232 IR
Tx Rx Tx RxG
Tx Rx Tx Rx
XTP RESET R
S/PDIFOUT
DTP
XTP
DTP
XTP
DTP
XTP
DTP
+48V
MIC/LINE1 1 3
2 42
3
4
LIN
K
EXP
HDBTHDBT G
7 8
DTP
CR
OSS
PO
INT
84 4
K RS-232 IR
Tx Rx Tx RxG
OVER TP
OVER TP
SIG LINK
IN
SIG LINK
IN
AU
DIO
OU
TP
UT
S
AU
DIO
INP
UT
S
DM
P E
XPA
NS
ION
CO
NT
RO
L
AM
P O
UT
PU
T
INP
UT
SO
UT
PU
TS
SIG LINK
OUT
3B
RS-232 IR
Tx Rx RTSCTSG
1L R 1
L R3
L R 3L R
5L R
2L R 4L R 2L R 4L R6L R
Tx Rx G 1 21 2
S GS G
C 3 4 C +V
PWR OUT = 6W
+V D -S +S
Tx Rx G Tx Rx G 1 2 3 4 G REMOTE
COM 1 COM 3COM 2 DIGITAL I/OLAN 1
LAN 2 LAN 3 CLASS 2 WIRING
1
L R
8Ω / 4Ω
IR/SERIAL RELAYS DIGITAL I/O
Extron Extron
Help SystemOff
Display
RoomControl
Off
Mute
Screen
Lighting December 15, 2013 - 7:58 AM AudioControl
Volume
Mute
Tuner 1 2 3VCRLaptop PC DVDDocCam
TunerOn
Channel
Last
Presets
MorePresets
321
654
987
Enter0
HDMI IN
ExtronDTP T EU 4K 331DTP Transmitter for EU-type Junction Boxes
Display
Extron DTP HDMI 4K 330 RxReceiver
RS-232 HDMI
Display
RS-232 HDMI
CATx Cable up to 330' (100 m)
CATx Cable up to 330' (100 m)
CATx Cable up to 230' (70 m)
CATx Cable up to 330' (100 m)
Extron DTP HDMI 4K 230 RxReceiver
Ethernet
Ethernet
AudioAudio
ExtronDTP T MK 4K 331DTP Transmitter forMK-type Junction Boxes
Inputs
OutputsAV
Control Network
Microphones
Extron DTP CrossPoint 84 4K IPCP SAScaling Presentation Matrix Switcher
ExtronSM 26Surface Mount Speakers
ExtronTLP Pro 1020T10" Tabletop TouchLink Pro Touchpanel
HDMI IN
Figure 3. Typical DTP Transmitter OperationFigure 2. Installation
468-2962-50 Rev. B
08 16
Extron Headquarters+800.633.9876 Inside USA/Canada Only
Extron USA - West Extron USA - East+1.714.491.1500 +1.919.850.1000
+1.714.491.1517 FAX +1.919.850.1001 FAX
Extron Europe+800.3987.6673
Inside Europe Only
+31.33.453.4040
+31.33.453.4050 FAX
Extron Asia+65.6383.4400
+65.6383.4664 FAX
Extron Japan+81.3.3511.7655
+81.3.3511.7656 FAX
Extron China+86.21.3760.1568
+86.21.3760.1566 FAX
Extron Middle East+971.4.299.1800
+971.4.299.1880 FAX
Extron Korea+82.2.3444.1571
+82.2.3444.1575 FAX
Extron India1800.3070.3777
(Inside India Only)
+91.80.3055.3777
+91.80.3055.3737 FAX
© 2016 Extron Electronics All rights reserved. All trademarks mentioned are the property of their respective owners. www.extron.com
DTP T EU 4K and DTP T MK 4K • Setup Guide (Continued)