Evaluation Board for the AD7091R Analog-to-Digital Converter · uses advanced design and process techniques to achieve ultralow power dissipation at high throughput rates. An Don-chip,

AD7091R User Guide UG-409

One Technology Way • P.O. Box 9106 • Norwood, MA 02062-9106, U.S.A. • Tel: 781.329.4700 • Fax: 781.461.3113 • www.analog.com

Evaluation Board for the AD7091R Analog-to-Digital Converter

PLEASE SEE THE LAST PAGE FOR AN IMPORTANT WARNING AND LEGAL TERMS AND CONDITIONS. Rev. 0 | Page 1 of 20

FEATURES Full-featured evaluation board for the AD7091R On-board power supplies Standalone capability PC control in conjunction with system demonstration

platform (EVAL-SDP-CB1Z) PC software for control and data analysis

EVAL-AD7091RSDZ CONTENTS Evaluation board hardware Evaluation software CD for the AD7091R Mains power supply adapter

ADDITIONAL EQUIPMENT NEEDED System demonstration platform (EVAL-SDP-CB1Z) when

using evaluation software Signal source

EVALUATION BOARD DESCRIPTION The EVAL-AD7091RSDZ is a full-featured evaluation board designed to allow the user to easily evaluate all features of the AD7091R analog-to-digital converter. The evaluation board can be controlled via the SDP connector (J4). The SDP board allows the evaluation board to be controlled through the USB port of a PC using the EVAL-AD7091RSDZ software.

On-board components include: the AD8031 high speed precision rail-to-rail op amp, the AD8032 high speed precision rail-to-rail dual op amp, and the ADP3303 high accuracy 200 mA low dropout linear regulator.

FUNCTIONAL BLOCK DIAGRAM

Figure 1. EVAL-AD7091RSDZ Block Diagram

DCJACKON-BOARD

POWER SUPPLY

AD7091R

SDP BOARD

CS

CONVST

SDO

SCLK

VDRIVE

ADSP-BF527DSP

VDD

DGND VDRIVE

VDD

AG

ND

LK5A BVDRIVE 3.3V LK6 A

B

VIN

VINBVIN

BIAS UP

1070

2-00

1

http://www.analog.com/ad7091R


http://www.analog.com/EVAL-SDP-CB1Z







http://www.analog.com/AD8031

http://www.analog.com/AD8032

http://www.analog.com/ADP3303


http://www.analog.com

UG-409 AD7091R User Guide

Rev. 0 | Page 2 of 20

TABLE OF CONTENTS Features .............................................................................................. 1

EVAL-AD7091RSDZ Contents ........................................................ 1

Additional Equipment Needed ....................................................... 1

Evaluation Board Description ......................................................... 1

Functional Block Diagram .............................................................. 1

Revision History ............................................................................... 2

EVAL-AD7091RSDZ Quick Start Guide ........................................ 3

Evaluation Board Hardware ............................................................ 4

Device Description ....................................................................... 4

Hardware Link Options ............................................................... 4

Power Supplies .............................................................................. 4

Sockets/Connectors ...................................................................... 5

Test Points ...................................................................................... 5

EVAL-AD7091RSDZ Basic Hardware Setup ............................. 6

Evaluation Board Software ...............................................................7

Software Installation .....................................................................7

Launching the Software ................................................................8

Description of Main Software Window .....................................9

Waveform Capture ..................................................................... 10

AC Testing—Histogram ............................................................ 11

DC Testing—Histogram ............................................................ 11

AC Testing—FFT Capture ........................................................ 12

Summary Tab .............................................................................. 13

Save File ....................................................................................... 13

Open File ..................................................................................... 13

Evaluation Board Schematics and Artwork ................................ 14

Ordering Information .................................................................... 18

REVISION HISTORY 8/12—Revision 0: Initial Version



EVAL-AD7091RSDZ QUICK START GUIDE Follow these steps to quickly evaluate the AD7091R:

1. Install the EVAL-AD7091RSDZ software from the enclosed CD. Ensure that the EVAL-SDP-CB1Z board is discon-nected from the USB port of the PC while installing the software. The PC may need to be restarted after the installation.

2. Ensure that the default link options are configured as outlined in Table 2.

3. Connect the EVAL-SDP-CB1Z board to the EVAL-AD7091RSDZ board as shown in Figure 2.

4. Screw the two boards together with the enclosed nylon screw/nut set to ensure that the boards connect firmly together.

5. Connect the power supply adapter included in the kit to Connecter J1 on the EVAL-AD7091RSDZ board.

6. Connect the EVAL-SDP-CB1Z board to the PC via the USB cable. For Windows® XP, you may need to search for the EVAL-SDP-CB1Z drivers. Choose to automatically search for the drivers for the EVAL-SDP-CB1Z board if prompted by the operating system.

7. Launch the AD7091R software from the Analog Devices subfolder in the Programs menu.

8. Connect a bipolar input signal via the VINB connector, J6. 9. Remove LK4.

Figure 2. Hardware Configuration—Setting Up the EVAL-AD7091RSDZ

POWER SUPPLIES

SDP BOARD

USBINTERFACE

9VDC INPUT

INPUTSIGNALAD7091R

BUFFERSTAGE

BIAS UP

1070

2-00

2















EVALUATION BOARD HARDWARE DEVICE DESCRIPTION This user guide describes the evaluation board for the AD7091R analog-to-digital converter.

The AD7091R is a 12-bit, ultralow power, successive approxima-tion ADC. The AD7091R operates from a single 2.7 V to 5.25 V power supply and is capable of achieving a throughput rate of 1 MSPS. The AD7091R also features an on-chip conversion clock, an accurate reference, and a high speed serial interface.

The conversion process and data acquisition are controlled using a CONVST signal and an internal oscillator. The AD7091R has a serial interface allowing data to be read after the conver-sion, while achieving 1 MSPS throughput rate. The AD7091R uses advanced design and process techniques to achieve ultralow power dissipation at high throughput rates. An on-chip, accurate 2.5 V reference is available.

Complete specifications for the AD7091R are provided in the AD7091R data sheet, available from Analog Devices, which should be consulted in conjunction with this user guide when using the evaluation board.

Full details on the EVAL-SDP-CB1Z are available at http://www.analog.com/EVAL-SDP-CB1Z.

HARDWARE LINK OPTIONS The functions of the link options are described in Table 2. The default setup is configured to operate the board with the mains power supply adapter and to interface to the EVAL-SDP-CB1Z board.

POWER SUPPLIES Care should be taken before applying power and signals to the evaluation board to ensure that all link positions are set according to the required operating mode. See Table 2 for the complete list of link options.

This evaluation board is supplied with a wall-mountable switching power supply that provides a 9 V dc output. Connect the supply to a 100 V to 240 V ac wall outlet at 50 Hz to 60 Hz.

The output from the supply is provided through a 2.0 mm inner diameter jack that connects to the evaluation board at J1. The 9 V supply is connected to the on-board 5 V linear regulator that supplies the correct bias to each of the various sections on the board and the EVAL-SDP-CB1Z board.

When using this evaluation board with the EVAL-SDP-CB1Z board, it is necessary to power the board through the J1 connector.

If the evaluation board is used without the 9 V adapter, an external power supply in the range of 2.7 V to 5.25 V must be connected to the VDD input to supply the AD7091R VDD pin. In addition, an external supply in the range of 1.65 V to 5.25 V must be connected to the VDRIVE input to supply the AD7091R VDRIVE pin.

Each supply is decoupled on this board using 10 µF tantalum and 100 nF multilayer ceramic capacitors.

There are two main ground planes, AGND and DGND. These are connected at one location close to the AD7091R.

Caution

When the EVAL-AD7091RSDZ evaluation board is connected to the EVAL-SDP-CB1Z, care must be taken to ensure that, if an external voltage is supplied to the VDRIVE input connector, J3, the voltage does not exceed 3.3 V. Otherwise, permanent damage may occur to the EVAL-SDP-CB1Z board.

Table 1. External Power Supplies Required Power Supply Voltage Range Purpose DC Jack 9 V ± 5% Supplies power to on-board

power management devices VDD 2.7 V to 5.25 V Analog supply rail VDRIVE 1.65 V to 5.25 V Digital supply rail without EVAL-

SDP-CB1Z connected 3.3 V ± 5% Digital supply rail with EVAL-

SDP-CB1Z connected

























Table 2. Link Options

Category Link Default Position Function

Buffer Settings

LK1 A This link is used to select the analog signal path. In Position A, the analog signal is buffered via U2, a unity gain buffer. In Position B, the analog signal is buffered via U3, a unity gain buffer. In Position C, the analog signal bypasses U2 and U3.

LK2 A This link is used to select the source of the analog input signal to the AD7091R. In Position A, the analog signal is sourced via the U2 op amp. In Position B, the analog signal is sourced via the U3 op amp. In Position C, the analog signal bypasses U2 and U3.

LK3 Fitted This resistor link option is used to select a biased signal as the analog input signal. Fitted—bias up circuit connected to the signal path. Not fitted—bias up circuit disconnected from the signal path.

Termination LK4 Inserted Adds a 51 Ω termination resistor to AGND at VIN. Inserted—51 Ω termination on the VIN input. Not inserted—no 51 Ω termination on the VIN input.

Power Supplies

LK5 A This link is used to select the source of the VDRIVE supply for the AD7091R. In Position A, the VDRIVE supply is sourced externally via the J3 connector. In Position B, the VDRIVE supply is sourced from the EVAL-SDP-CB1Z via the J4 connector.

LK6 A This link is used to select the source of the VDD supply for the AD7091R and on-board buffers. In Position A, the VDD supply is sourced internally from the on-board power supplies. In Position B, the VDD supply is sourced externally via the J2 connector.

SOCKETS/CONNECTORS The connectors and sockets on the EVAL-AD7091RSDZ are as outlined in Table 3.

Table 3. On-Board Connectors Connector Function J1 9 V, 2.0 mm dc jack connector J2 External VDD and AGND power connector J3 External VDRIVE and DGND power connector J4 120-way connector for EVAL-SDP-CB1Z interface J5 VIN analog input signal J6 VINB analog input signal to bias up circuit J7 External reference voltage connector

The default interface to this evaluation board is via the 120-way connector, which connects the EVAL-AD7091RSDZ to the EVAL-SDP-CB1Z board.

TEST POINTS There are numerous test points on the EVAL-AD7091RSDZ board. These test points enable the user to have easy access to the signals from the evaluation board for probing, evaluation, and debugging.

It is also possible to access the AD7091R via the test points to operate the EVAL-AD7091RSDZ in standalone mode without the need for the EVAL-SDP-CB1Z board.















EVAL-AD7091RSDZ BASIC HARDWARE SETUP The EVAL-AD7091RSDZ board connects to the EVAL-SDP-CB1Z system demonstration platform board. The EVAL-SDP-CB1Z board is the controller board, which is the communication link between the PC and the main evaluation board. Figure 2 shows a photograph of the connections between the EVAL-AD7091RSDZ daughter board and the EVAL-SDP-CB1Z board.

The analog input range to the AD7091R is 0 V to VREF and should not be exceeded. When using the on-chip reference, VREF is 2.5 V. An input signal in the range of 2.5 V p-p should be connected to the EVAL-AD7091RSDZ board via VIN or VINB.

A bipolar input signal should be connected to VINB, the J6 connector. This signal is biased to 1.25 V via the bias up circuitry on the EVAL-AD7091RSDZ. The signal source should be a low impedance source. An on-board unity gain amplifier buffers the signal to the AD7091R. This is the default configura-tion on the EVAL-AD7091RSDZ.

A unipolar input signal should be connected to VIN, the J5 connector. An on-board unity gain amplifier buffers the signal to the AD7091R.

Before connecting power, connect the EVAL-AD7091RSDZ board to Connector A on the EVAL-SDP-CB1Z board. A nylon screw/nut set is included in the EVAL-AD7091RSDZ kit and can

be used to ensure that the EVAL-AD7091RSDZ and EVAL-SDP-CB1Z boards are connected firmly together.

Ensure that the link options are in the default positions as outlined in Table 2.

After the EVAL-AD7091RSDZ board and the EVAL-SDP-CB1Z board are connected securely, connect the power to the EVAL-AD7091RSDZ board. The EVAL-AD7091RSDZ board requires an external power supply adapter, which is included in the evaluation board kit. Connect this power supply to Connector J1 on the EVAL-AD7091RSDZ board. For further details on the required power supply connections and options, see the Power Supplies section.

Before connecting the EVAL-SDP-CB1Z board to your PC, ensure that the EVAL-AD7091RSDZ software has been installed from the enclosed CD. The full software installation procedure is detailed in the Evaluation Board Software section.

Finally, connect the EVAL-SDP-CB1Z board to the PC via the USB cable enclosed in the EVAL-SDP-CB1Z kit. If using a Windows XP platform, you may need to search for the EVAL-SDP-CB1Z drivers. Choose to automatically search for the drivers for the EVAL-SDP-CB1Z board if prompted by the operating system.


































EVALUATION BOARD SOFTWARE SOFTWARE INSTALLATION The EVAL-AD7091RSDZ kit includes software on a CD. Double-click the setup.exe file from the CD to run the install. The default location for the software is

C:\Program Files\Analog Devices\AD7091R\

Install the evaluation software before connecting the evaluation board and the EVAL-SDP-CB1Z board to the USB port of the PC to ensure that the evaluation system is correctly recognized when connected to the PC.

There are two parts to the installation:

• EVAL-AD7091RSDZ board software installation • EVAL-SDP-CB1Z system demonstration platform board

drivers installation

Follow Step 1 to Step 4 (see Figure 3 to Figure 6) to install the EVAL-AD7091RSDZ software. Follow Step 5 to Step 8 (see Figure 7 to Figure 10) to install the EVAL-SDP-CB1Z drivers. Proceed through all of the installation steps, allowing the software and drivers to be placed in the appropriate locations. Connect the EVAL-SDP-CB1Z board to the PC only after the software and drivers have been installed.

Figure 3. EVAL-AD7091RSDZ Installation—User Account Control

1. Click Yes to begin the installation process.

Figure 4. EVAL-AD7091RSDZ Installation—Destination Directory

2. Select the installation directory. Click Next.

Figure 5. EVAL-AD7091RSDZ Installation—Start Installation

3. Click Next to install the software.

Figure 6. EVAL-AD7091RSDZ Installation—Installation Complete

4. The installation of the evaluation software completes. Click Next to proceed with the installation of the drivers.

Figure 7. EVAL-SDP-CB1Z Drivers Installation—Setup Wizard

5. The setup wizard opens. Click Next to begin the driver installation process.

1070

2-00

310

702-

004

1070

2-00

510

702-

006

1070

2-00

7















Figure 8. EVAL-SDP-CB1Z Drivers Installation—Choose Install Location

6. Select a destination folder for the SDP drivers, and click Install.

Figure 9. EVAL-SDP-CB1Z Drivers Installation—Windows Security

7. Click Install to proceed with the installation.

Figure 10. EVAL-SDP-CB1Z Drivers Installation—Complete

8. Click Finish.

After installation from the CD is complete, connect the EVAL-AD7091RSDZ board to the EVAL-SDP-CB1Z board as described in the Evaluation Board Hardware section.

When you first plug in the EVAL-SDP-CB1Z board via the USB cable provided, allow the Found Hardware Wizard to run. After the drivers are installed, you can check that the board is connected correctly by looking at the Device Manager of the PC. The Device Manager can be found by right-clicking My Computer > Manage > Device Manager from the list of System Tools, as shown in Figure 11. The EVAL-SDP-CB1Z SDP-B board should appear under ADI Development Tools. This completes the installation.

Figure 11. Device Manager

LAUNCHING THE SOFTWARE After the EVAL-AD7091RSDZ and EVAL-SDP-CB1Z boards are correctly connected to your PC, the EVAL-AD7091RSDZ software can be launched.

To launch the software, perform the following steps:

1. From the Start menu, select Programs >Analog Devices > AD7091R. The main window of the software then opens (see Figure 13).

2. If the EVAL-AD7091RSDZ board is not connected to the USB port via the EVAL-SDP-CB1Z when the software is launched, a connectivity error displays (see Figure 12). Connect the evaluation board to the USB port of the PC, wait a few seconds, click Rescan, and follow the instructions.

Figure 12. Connectivity Error Alert

1070

2-00

810

702-

009

1070

2-01

0

1070

2-01

110

702-

012
















Figure 13. Evaluation Software Main Window

DESCRIPTION OF MAIN SOFTWARE WINDOW The following tools allow user control of the different chart displays. When the software is launched, the main software window opens (see Figure 13).

The user software panel as shown in Figure 13 has the following features:

• Menu bar • Control buttons • Data capture display

Menu Bar

The menu bar consists of the File and Help menus.

File Menu

Open (Sample Data). Loads previously captured data in TSV (tab separated values) format for analysis.

Save (Sample Data). Saves captured data in TSV (tab separated values) format for future analysis.

Print Front Panel Picture. Prints the software window displayed.

Save As Picture. Saves the front panel as a JPEG file.

Exit. Exits the program.

Help Menu

Open analog.com. Opens www.analog.com.

Control Buttons

The EVAL-AD7091RSDZ software includes the following control buttons, drop-down boxes, and indicators.

Mode. Selects the operating mode of the AD7091R. In Normal mode, the ADC is ready to acquire samples. In Sleep mode, the device enters power-down mode when the SAMPLE button is clicked.

Sampling rate. Selects the sampling rate of the data acquisition.

# Samples. Selects the number of samples to be completed in a single acquisition.

SAMPLE. Initiates the sampling and readback of the defined number of measurements.

CONTINUOUS. Performs a continuous capture from the ADC. Click a second time to stop sampling.

1. MENU BAR.2. CONTROL BUTTONS.3. DATA CAPTURE DISPLAY.

1

2

3

1070

2-01

3

http://www.analog.com/




FLASH LED. Causes the orange LED1A on the SDP board to flash, which can be a useful debugging tool.

STOP. Stops the program.

Data Capture Display

There are four tabs that display the conversion data in different formats: Waveform, Histogram, FFT, and Summary.

The tools shown in Figure 14 allow user control of the different chart displays.

Figure 14. Chart Tools

WAVEFORM CAPTURE Figure 15 illustrates the waveform capture tab.

The waveform analysis reports the amplitudes recorded from the captured signal in addition to the frequency of the signal tone.

Figure 15. Waveform Capture Tab

1 2 3

1. USED FOR CONTROLLING THE CURSOR IF PRESENT.2. USED FOR ZOOMING IN AND OUT.3. USED FOR PLANNING. 10

702-

014

1

1. WAVEFORM ANALYSIS. 1070

2-01

5



Figure 16. Histogram Capture Tab

AC TESTING—HISTOGRAM Figure 16 shows the histogram capture tab. This tests the ADC for the code distribution for the ac input and computes the mean and standard deviation, or transition noise of the converter, and displays the results.

Raw data is captured and passed to the PC for statistical computations. To perform a histogram test, select the Histogram tab in the evaluation software main window and click the SAMPLE button.

Note that an ac histogram requires a quality signal source applied to the input VIN/VINB connectors.

DC TESTING—HISTOGRAM The histogram is more commonly used for dc testing. Similar to ac testing, this tests the ADC for the code distribution for the dc input and computes the mean and standard deviation, or transi-tion noise of the converter, and displays the results. Raw data is captured and passed to the PC for statistical computations. To perform a histogram test, select the Histogram tab in the evalua-tion software main window and click the SAMPLE button.

1070

2-01

6

1



Figure 17. FFT Capture Tab

AC TESTING—FFT CAPTURE Figure 17 shows the FFT capture tab. This tests the traditional ac characteristics of the converter and displays a fast Fourier transform (FFT) of the results. As in the histogram test, raw data is captured and passed to the PC where the FFT is performed, displaying SNR, SINAD, THD, and SFDR. To perform an ac test, apply a sinusoidal signal to the evaluation board at the SMB input, J5 or J6. Low distortion, better than 115 dB, is required to allow true evaluation of the part. One possibility is to filter the input signal from the ac source. There is no sug-gested band-pass filter but consideration should be taken in the

choice. Furthermore, if using a low frequency band-pass filter when the full-scale input range is more than a few volts peak to peak, it is recommended to use the on-board amplifiers to amplify the signal, thus preventing the filter from distorting the input signal.

Figure 17 displays the results of the captured data.

• Section 1 shows the input signal information. • Section 2 displays the fundamental frequency and

amplitude in addition to the 2nd to 5th harmonics. • Section 3 displays the performance data: SNR, dynamic

range, THD, SINAD, and noise performance.

1 2 3

1. INPUT SIGNAL INFORMATION.2. FUNDAMENTAL FREQUENCY AND AMPLITUDE.3. PERFORMANCE DATA. 10

702-

017



Figure 18. Summary Tab

SUMMARY TAB Figure 18 shows the summary tab. The summary tab captures all the display information and provides them in one panel with a synopsis of the information, including key performance parameters such as SNR and THD.

SAVE FILE The software can save the current captured data for future analysis.

Go to the File menu, and click Save (Sample Data). The save dialog box opens. Save to an appropriate folder location.

Figure 19. Save File dialog Box

OPEN FILE The software can load captured data for analysis.

Go to the File menu, and click Open (Sample Data). The open file dialog box opens. Load an appropriate file.

Figure 20. Open File Dialog Box

1070

2-01

8

1070

2-01

9

1070

2-02

0



EVALUATION BOARD SCHEMATICS AND ARTWORK

Figure 21. Schematic Page 1

VIN

B

EX

T_

RE

F

VIN

1VD

D

2RE

FOU

T

3AI

N

4RE

GCA

P

5G

ND

6CO

NVS

TB

7CS

B

8SC

LK

9SD

O

10VD

R IV E

U1

AD70

91

C10

0.1u

F

C12

1uF

C11

0.1u

F

C14

1uF

C15

0.1u

F

C9 1uF

T9

R31

51r

C13

4.7n

F

2-

3+

6O

P

4V-

7V+

U3

AD86

55

C11u

F

C20.

1uF

T2

R10

0r

C16

DN

I

R11

DN

I

C868

pF

C31u

F

R63K

R3 DN

I

R2 3K

R51K

5

C40.

1uF

C50.

1uF

R40r

C27

DN

I

R1 1K5

T4T7T8T1

0

T6T5T1 T3

J6

J7

8V+

4V-

U4-

CAD

8032

ARM

Z

5+

6-

7

U4

-B

AD

80

32

AR

MZ

3+

2-

1

U4

-A AD

80

32

AR

MZ

2-

3+

6O

P 4V-

7V+

U2

AD8 0

31

C61u

F

C70.

1uF

R80r

C28

DN

I

R9 DN

I

J5

LK4 R7 51

r

CBALK1

CBALK2

LK3

DN

I

AVD

D

CON

VST

CSSCLK

VDRI

VE

VREF

AVD

D

VREF

AVD

D

SDO

AVD

D

10702-021




VD

D

GN

D

VD

RIV

E

DG

ND

An

alo

gp

ow

er

su

pp

ly

Po

we

rs

up

ply

for

SD

Pb

oa

rd

C24

0.1u

F+

C25

10uF

J2-1

J2-2

J3-1

J3-2

B A

LK6

8IN

17

IN2

5SD

4GN

D

1O

UT1

2O

UT2

6ER

RO

R3

NR

U6

AD

P330

3-5

C18

10nF

R12

330k

C17

10nF

C26

1uF

J1-3

J1-4 J1

-1

J1-2

C19

0.1u

F+

C20

10uF

1IN

2

GN

D

3O

UT

LC1

EMC

_FIL

TER

1nF

1IN

2

GN

D

3O

UT

LC2

EMC

_FIL

TER

1nF

5V

IN

4EN

3FB

6SW

2

GN

D

1B

ST

U7

AD

P2

30

1A

UJZ

+C

2110

uF

+C

2310

uF

C22

0.1u

F

D1

30V

,2A

R15 53

k6

R16 10

k2

B A

LK5

R14

1K5

R13

3K

L1

6.8u

H

VIO

_CO

NN

ECTO

R

VD

RIV

E

AV

DD

V_I

N

VSD

P_EN

VSD

P_EN

VSD

P

V_I

N

10702-022




Bo

ard

IDE

EP

RO

M(2

4LC

32

/64

)m

ust

be

on

I2C

bu

s0

VIO

:U

SE

tose

tIO

volt

ag

em

ax

dra

w2

0m

A

VIN

:U

seth

isp

into

po

we

rth

eS

DP

req

uir

es

4-7

V2

00

mA

EE

PR

OM

A0

pin

wir

ed

toco

nn

ect

or

pin

56

sele

cts

sla

vea

dd

ress

ba

sed

on

wh

ich

SD

Pco

nn

ect

or

isu

sed

*N

Co

nB

LAC

KFI

NS

DP

****

****

*

****

TIM

ER

S

INP

UT

/OU

TP

UT

GE

NE

RA

L

I2C

SP

I

SP

OR

T

PO

RT

PA

RA

LLE

L

SD

PS

TA

ND

AR

DC

ON

NE

CT

OR

12

0N

C

11

9N

C

11

8G

ND

11

7G

ND

11

6V

IO(+

3.3

V)

11

5G

ND

11

4P

AR

_D

22

11

3P

AR

_D

20

11

2P

AR

_D

18

11

1P

AR

_D

16

11

0P

AR

_D

15

10

9G

ND

10

8P

AR

_D

12

10

7P

AR

_D

10

10

6P

AR

_D

8

10

5P

AR

_D

6

10

4G

ND

10

3P

AR

_D

4

10

2P

AR

_D

2

10

1P

AR

_D

0

10

0P

AR

_W

R

99

PA

R_

INT

98

GN

D

97

PA

R_

A2

96

PA

R_

A0

95

PA

R_

FS2

94

PA

R_

CLK

93

GN

D

92

SP

OR

T_

RS

CLK

91

SP

OR

T_

DR

0

90

SP

OR

T_

RFS

89

SP

OR

T_

TFS

88

SP

OR

T_

DT

0

87

SP

OR

T_

TS

CLK

86

GN

D

85

SP

I_S

EL_

A

84

SP

I_M

OS

I

83

SP

I_M

ISO

82

SP

I_C

LK

81

GN

D

80

SD

A_

0

79

SC

L_0

78

GP

IO1

77

GP

IO3

76

GP

IO5

75

GN

D

74

GP

IO7

73

TM

R_

B

72

TM

R_

D

71

NC

70

NC

69

GN

D

68

NC

67

NC

66

NC

65

NC

64

NC

63

GN

D

62

UA

RT

_T

X

61

BM

OD

E1

60

RE

SE

T_

IN5

9U

AR

T_

RX

58

GN

D5

7N

C5

6N

C5

5N

C5

4N

C5

3N

C5

2G

ND

51

NC

50

NC

49

TM

R_

C4

8T

MR

_A

47

GP

IO6

46

GN

D4

5G

PIO

44

4G

PIO

24

3G

PIO

04

2S

CL_

14

1S

DA

_1

40

GN

D3

9S

PI_

SE

L1/S

PI_

SS

38

SP

I_S

EL_

C3

7S

PI_

SE

L_B

36

GN

D3

5S

PO

RT

_IN

T3

4S

PO

RT

_D

T3

33

SP

OR

T_

DT

23

2S

PO

RT

_D

T1

31

SP

OR

T_

DR

13

0S

PO

RT

_D

R2

29

SP

OR

T_

DR

32

8G

ND

27

PA

R_

FS1

26

PA

R_

FS3

25

PA

R_

A1

24

PA

R_

A3

23

GN

D2

2P

AR

_C

S2

1P

AR

_R

D2

0P

AR

_D

11

9P

AR

_D

31

8P

AR

_D

51

7G

ND

16

PA

R_

D7

15

PA

R_

D9

14

PA

R_

D1

11

3P

AR

_D

13

12

PA

R_

D1

41

1G

ND

10

PA

R_

D1

79

PA

R_

D1

98

PA

R_

D2

17

PA

R_

D2

36

GN

D5

US

B_

VB

US

4G

ND

3G

ND

2N

C1

VINJ4

1A

02

A1

3A

24

VS

S

8V

CC

7W

P6

SC

L5

SD

A

U5

24

LC3

2

R1

8

DN

IR

19

DN

I

R1

7D

NI

R2

5 DN

I

R2

4

DN

I

R2

6D

NI

R2

71

00

K

R2

81

00

K

R2

0

0r

R2

1

0r

R2

2

0r

R2

3

0r

VIO

_C

ON

NE

CT

O

VIO

_C

ON

NE

CT

OR

SC

LK

CS

SD

O

CO

NV

ST

CO

NV

ST

VS

DP

10702-023



Figure 24. EVAL-AD7091RSDZ Top-Side Silkscreen

Figure 25. EVAL-AD7091RSDZ Top Layer

Figure 26. EVAL-AD7091RSDZ Bottom Layer

1070

2-02

410

702-

025

1070

2-02

6






ORDERING INFORMATION See Table 4 for a list of the evaluation boards compatible with the hardware described in this user guide.

Table 4. Compatible Boards Model1 Description EVAL-AD7091RSDZ AD7091R evaluation board EVAL-SDP-CB1Z Evaluation controller board ADZS-BRKOUT-EX3 Signal breakout board 1 Z = RoHS-compliant part.




http://www.analog.com/ug-282



NOTES



NOTES

ESD Caution ESD (electrostatic discharge) sensitive device. Charged devices and circuit boards can discharge without detection. Although this product features patented or proprietary protection circuitry, damage may occur on devices subjected to high energy ESD. Therefore, proper ESD precautions should be taken to avoid performance degradation or loss of functionality.

Legal Terms and Conditions By using the evaluation board discussed herein (together with any tools, components documentation or support materials, the “Evaluation Board”), you are agreeing to be bound by the terms and conditions set forth below (“Agreement”) unless you have purchased the Evaluation Board, in which case the Analog Devices Standard Terms and Conditions of Sale shall govern. Do not use the Evaluation Board until you have read and agreed to the Agreement. Your use of the Evaluation Board shall signify your acceptance of the Agreement. This Agreement is made by and between you (“Customer”) and Analog Devices, Inc. (“ADI”), with its principal place of business at One Technology Way, Norwood, MA 02062, USA. Subject to the terms and conditions of the Agreement, ADI hereby grants to Customer a free, limited, personal, temporary, non-exclusive, non-sublicensable, non-transferable license to use the Evaluation Board FOR EVALUATION PURPOSES ONLY. Customer understands and agrees that the Evaluation Board is provided for the sole and exclusive purpose referenced above, and agrees not to use the Evaluation Board for any other purpose. Furthermore, the license granted is expressly made subject to the following additional limitations: Customer shall not (i) rent, lease, display, sell, transfer, assign, sublicense, or distribute the Evaluation Board; and (ii) permit any Third Party to access the Evaluation Board. As used herein, the term “Third Party” includes any entity other than ADI, Customer, their employees, affiliates and in-house consultants. The Evaluation Board is NOT sold to Customer; all rights not expressly granted herein, including ownership of the Evaluation Board, are reserved by ADI. CONFIDENTIALITY. This Agreement and the Evaluation Board shall all be considered the confidential and proprietary information of ADI. Customer may not disclose or transfer any portion of the Evaluation Board to any other party for any reason. Upon discontinuation of use of the Evaluation Board or termination of this Agreement, Customer agrees to promptly return the Evaluation Board to ADI. ADDITIONAL RESTRICTIONS. Customer may not disassemble, decompile or reverse engineer chips on the Evaluation Board. Customer shall inform ADI of any occurred damages or any modifications or alterations it makes to the Evaluation Board, including but not limited to soldering or any other activity that affects the material content of the Evaluation Board. Modifications to the Evaluation Board must comply with applicable law, including but not limited to the RoHS Directive. TERMINATION. ADI may terminate this Agreement at any time upon giving written notice to Customer. Customer agrees to return to ADI the Evaluation Board at that time. LIMITATION OF LIABILITY. THE EVALUATION BOARD PROVIDED HEREUNDER IS PROVIDED “AS IS” AND ADI MAKES NO WARRANTIES OR REPRESENTATIONS OF ANY KIND WITH RESPECT TO IT. ADI SPECIFICALLY DISCLAIMS ANY REPRESENTATIONS, ENDORSEMENTS, GUARANTEES, OR WARRANTIES, EXPRESS OR IMPLIED, RELATED TO THE EVALUATION BOARD INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTY OF MERCHANTABILITY, TITLE, FITNESS FOR A PARTICULAR PURPOSE OR NONINFRINGEMENT OF INTELLECTUAL PROPERTY RIGHTS. IN NO EVENT WILL ADI AND ITS LICENSORS BE LIABLE FOR ANY INCIDENTAL, SPECIAL, INDIRECT, OR CONSEQUENTIAL DAMAGES RESULTING FROM CUSTOMER’S POSSESSION OR USE OF THE EVALUATION BOARD, INCLUDING BUT NOT LIMITED TO LOST PROFITS, DELAY COSTS, LABOR COSTS OR LOSS OF GOODWILL. ADI’S TOTAL LIABILITY FROM ANY AND ALL CAUSES SHALL BE LIMITED TO THE AMOUNT OF ONE HUNDRED US DOLLARS ($100.00). EXPORT. Customer agrees that it will not directly or indirectly export the Evaluation Board to another country, and that it will comply with all applicable United States federal laws and regulations relating to exports. GOVERNING LAW. This Agreement shall be governed by and construed in accordance with the substantive laws of the Commonwealth of Massachusetts (excluding conflict of law rules). Any legal action regarding this Agreement will be heard in the state or federal courts having jurisdiction in Suffolk County, Massachusetts, and Customer hereby submits to the personal jurisdiction and venue of such courts. The United Nations Convention on Contracts for the International Sale of Goods shall not apply to this Agreement and is expressly disclaimed.

©2012 Analog Devices, Inc. All rights reserved. Trademarks and registered trademarks are the property of their respective owners. UG10702-0-8/12(0)

Documents

Evaluation Board for the AD7091R Analog-to-Digital Converter · uses advanced design and process techniques to achieve ultralow power dissipation at high throughput rates. An Don-chip,