ERICSSON RBS [3922(ID) & 3967(OD)] {3G} Commissioning stepsERICSSON RBS [3922(ID) & 3967(OD)] {3G} Commissioning stepsERICSSON RBS [3922(ID) & 3967(OD)] {3G} Commissioning stepsERICSSON RBS [3922(ID) & 3967(OD)] {3G} Commissioning steps

First of all, Software named as WS_FTP and folder UP to be saved in c:\ drive for convenient.

Phase-I Instruction: - Cable should be logged in test port on CBU card of BTS (Node B), and cable used in these steps is USB to DB9 (male) & DB9(female) to RJ45(male) for laptop connectivity.

Start All programs Accessories Communication hyper terminal type RBS (select com port)

Now click on Restore Defaults and then click OK after that a window will appear and when the port is connected the sign $ will be appear on the window]

Click on it then click on OK

Select com port on which your cable device is installed

1 2

When it doesnt stop at $ sign and it continues displaying information then to stop it give reload command.

There are two modes of operation i.e. 1) Basic and 2) Backup.

To bring the Backup mode from Basic mode [After running WS_FTP software]

1) $ reload-- [BTS Backup mode will come and BTS starts sound.]

Note: - There is storage memory in BTS and also it has partitioned in two logical drive, and the name is given as c2 & D drive. You can check the volume used through the vols command. And for further process proceed to next steps.

2) $ vols [ it will show the storage details like below now you have to format both drive c2 &D]

3) $ formathd /c2 [After giving this command it will ask for continuing y/n]

4) : y [C2 drive will be formatted after this command] 5) $ formathd /d [Again like above it will ask for conformation yes or no]

6) : y [D drive will be formatted after this command]

7) $ vols [this command for drive volume if it shows 0%, it means drive is formatted]

8) $ ifconfig [to check whether there is IP or not]

Most of the time node B IP is configured by default, but if it is not configured in case then for setting the IP of node B there is command , But sometimes it doesnt take command and it give error then in this case give the command reload(only, no --) and then again give the same command for setting the IP, after giving the command if on terminal window shows only dollar sign then it means IP for node B is configured.

[If command doesnt run the again give command $ reload ] Now you can verify via ifconfig command whether your IP has been set or not. For setting new IP for node B is as below,

9) $ ifconfig le0 169.254.1.1 netmask 255.255.0.0

10) $ ifconfig [To check whether set IP is being shown or not]

Phase -II Instruction: - Cable should be logged in Ethernet port on CBU card of BTS (Node B)

Now set the IP address of Laptop as {IP address-169.254.1.2, Subnet mask- 255.255.0.0}

Then run the software [WS_FTP95]

Error in IP configuration

Double click on this icon

Command for IP configuration

After running the software in session properties it will ask for user ID and password for login then give the details as

User ID: - rbs Password: - rbs [After connection establishment a sound will occur, it is software property]

Note: - Your software window looking like below, in this the right window is showing the contents of BTS storage and left is for computer storage. If it is not showing like below then you can select the path location by clicking up arrow showing in this window for both side.

The basic thing is that you have to copy the contents of folder c2 & d from laptop to BTS for that you have to adjust the path location of BTS and computer same like below for convenient.

Now select both side c2 and d and click on arrow for file transfer, remember right side is for BTS and left is for laptop so choose arrow as in which direction you have to copy the folder contents.

Click on this arrow for path adjustment

Select both side these two folders

Click on this arrow for starting file transfer

1 1

2

3

After clicking on the yes in option popped data will start transferring then wait for some moment until transferring completed.

And the sign of completion of transfer is a sound will occur and a message will come like closing data connection, it implies that initial CV has been done.

Phase-III Start Run cmd [save the UP folder in C drive for convenient] 1) cd c:\ [ To enter into the c:\ drive] 2) cd UP [To enter into the UP folder] 3) cd cxp901161* [To enter into the CXP9011610_R12F%5 folder] 4) cd sw_install [To enter into the sw_install folder] 5) dir [To show the subfolders inside sw_install folder] 6) cd cxp* [To enter into the cxp* folder] 7) dir [To show the subfolders] 8) sw_load.bat 169.254.1.1 rbs rbs [where first rbs is user name and second one is password]

Note: - Left side window shows all 8 commands given above and in last 8th command after hitting on enter loading will be started from UP folder to BTS and it will take time. At the end last path will be shown on the command prompt as shown in right command window it implies loading is done.

Phase-IV Again to bring back the basic mode from the backup mode go to hyper terminal from start menu and also change the port from Ethernet to Test port. And type command in the hyper terminal window as follows, $ reload [BTS sound will lee off] ** Login server ready** [this message will be shown].

Phase-V Note: - For this part first of all JRE (Java) folder to be installed on your computer, Then connect into Ethernet port 1) Go to internet explorer and type in address bar 169.254.1.1/em/index.html [click on run& connect]

Element Manager

Type here then press enter

After hitting on enter the following window will come and it starts loading the element manager.

Then element manager will be open like this

2) Equipment 1A2 for RU cards 1B2 for FU cards Show these Cards. 1A1 CBU/Tx/Rx Right click on properties

LDN (last one to be selected from the option)

Select equipment here

Right click on 1A1 to select properties here

1

2

3

Next + to be clicked to have Now this will show Backplane serial No. [Note it down or take screen short for record, It is important for licensing]

Note: - CV to be created after each and every function Software config version create [Name: - after_P5] add list apply set startable ok

Swmanagement

Right click

Select software from here 1

2

Right click here

Now its time to run the scripts To run the scripts (3 scripts is there i.e. external hw/OAM/IUB, before running this save it in one folder as test node for your convenient)

1

2

3

1

2

RNC RNC 05 EN Site

Select this script

Steps for running scripts------ For external hw 1) Config site equipment next Browse [script path to be given] Nextnext..> finish ( ext.alarm)

1

2

3

4 5

6

7

8

Notice this its showing 11(11) and in above snaps it is showing 1(12) means you have go through 12 steps for this process

Just you have to hit next until it completed successfully

For OAM 2) Config OAM access do as above. It will show 3 PCM ok [current link setting shown] Note: - After this the IP address will be changed and also according to that u have to change your laptop IP address. Remember one thing the IP address should be one ahead of that BTS IP. ***Go to internet explorer and type the newly created IP in address bar like, IP (newly created)/em/index.html [em will be made automatically]

1

2

3

4 5

6 7

Click on next until its got completed successfully in between this it will show a new IP note it down for next time login.

For IUB Note: - First two paragraphs of IUB to be cut from the original one and to be saved as .txt extension Now config run command file browse [script path to be given which is saved as .txt file] Halt on errors verbose logging

Start Close

1

2

3

5

4

6 7

When configuration successfully done then close i.e. click on 7

Equipment ATM Layer ATM port -1-1-ima1 VplTpID = vp1 (right click properties ) 13200 Attributes ( U3P13200M8800 to be selected from the list )

Search

ATM Traffic Descriptor ID

>=

Search

Set Apply Ok

Right click on it

1

2 3

4

5

6

7

8

Then at last as usual again CV to be created as like before and the name of CV should be as (after_all_scipts).

Select this one from list

9

10

12 11 Select ATM from here for checking whether our three E1 status is enable it means Site successfully integrated

1

2 Operation status

BP_FTP Application (Bullet Proof_ File Transfer Protocol) Licensing First of all BP_FTP application to be installed then get started with the following steps Go to internet explorer and type in address bar IP (Node B IP newly created)/em/index.html You have to create user account first in this application,

BPFT (s/w appl.) Right click in User accounts and add account name rbs and set login and password both as rbs for convenience and home IP set as -=All IP Homes=- Then go to Access Rights and give the path and then select All/None (Delete should be un ticked)

Then click Ok after that go online using button Then go to element manager and then follow the steps below, Configuration License update keyfile Username Password IP address (newly created node B IP should be given) License file (** License file name to be copied and pasted as .xml extension) Configuration upgrade license key file

Phase VI Up gradation into P6

BPFT in access rights give directories then All/None (Delete should be un ticked) Ok Then again go to element manager application and follow the instruction as below Software Upgrade package (right click) create User label File user label FTP server address it should be given Node B IP User name rbs Password rbs Create package Install Full install Hard upgrade Upgrade node Verify package (If it stops) ** After this step Node B will upgrade into P6** **Wherever the file name is asked in these steps, the software used to upgrade in P6 folder in that an xml file containing same file name should be used. And also where it asked to use .xml extension there should be file name pasted and after that give .xml as extension.

rbs

rbs

%9 folder name xml file name to be copied Software folder to be selected which has to be run in P6

./ name to be pasted as .xml extension dot and forward slash should be given before file name

Upgrade exending