Upload
others
View
1
Download
1
Embed Size (px)
Citation preview
ERA INN EDGE SV ACTHE SILENT AND SMART SOLUTION FOR AUTOMATING INTERIOR VENETIAN BLINDS
NAMEERA INN EDGE SV AC
Tubular motor with electronic limit switch, practical dry contact input and built-in receiver. Ideal for interior venetian blinds.S size Ø 35 mm.
Silent
Minimum vibrations and silent operation for maximum acoustic comfort.
Noise 35 dBA.
Comfort
Constant motor rotation speed during opening and closing, whatever the load conditions: perfect alignment between all blinds even in multiple installations. Possibility of setting up and down movement times.
Smart
The obstacle detection function can be activated during opening.
Tilting function
The tilt of the slats in the interior venetian blinds can be adjusted in any position of the travel. The required tilt can be recalled by the up and down buttons on the transmitter or the Agio and Era P Vario slider.
Go To Position functionA simple touch of the Agio or Era P Vario slider takes the blind to the position corresponding to the pressure point, from 0 to 100% of travel.
Customisation
Maximum slat tilt can be programmed and intermediate positions can be memorised.
Adjustable up and down speed.
Compatibility with other systems The practical dry contact input allows Era Inn Edge tubular motors to be connected to any system with dry contact technology available on the market. Easy to install Each motor can be programmed individually, without needing to power off the other motors in the same system. • Via radio, using Nice transmitters. • Via a wired connection, using the TTPRO palmtop programmer. Greater acoustic and visual comfort Electronically controlled Soft Start and Soft Stop functions allow different acceleration and deceleration levels to be set in the sections near the limit switches.
Precise and quick limit switch adjustment with two buttons on the motor head.
Simplified programming thanks to the two-colour diagnostic LED.
Energy savings Low power consumption both during operation and in standby.
Practical 1.5 m long cable with connector to simplify installation and maintenance operations.
Extended operation without the risk of overheating.
BUTTONS FOR PRECISE AND QUICK LIMIT SWITCH ADJUSTMENT
CODE DESCRIPTION PCS./PACK CERTIFICATES
E EDGE SV 332 AC ELECTRONIC LIMIT SWITCH, DRY CONTACT AND BUILT-IN RECEIVER100-240 Vac, 3 Nm, 32 rpm. FOR INTERIOR VENETIAN BLINDS
1 SASO
E EDGE SV 620 AC ELECTRONIC LIMIT SWITCH, DRY CONTACT AND BUILT-IN RECEIVER100-240 Vac, 6 Nm, 20 rpm. FOR INTERIOR VENETIAN BLINDS
1 SASO
NB: When ordering, specify the required certification.
CCONNECTORS FOR DRY CONTACT INPUT
TWO-COLOUR LED TO SIMPLIFY PROGRAMMING
ANTENNA CABLE
CA0274A00
CA0275A00
CA0276A00
CA0277A00
CA0278A00
Ø13
Ø38
ERA INNACTIONSMALL
ERA INNEDGE/SMART
SMALL
111
11
L
L
10
4
24
Ø35
,2
Ø3,2
29
1
Ø35
,2
24
Ø38
Ø13 Ø3,2
29
10
4
E EDGE SV 332 AC E EDGE SV 620 AC
100-240 / 50-600.6 0.840 50
<0.5
3 632 2048 3216 10
35<150
10 612 22
7441.51.5
0 ÷ 60795x100x100
POWER CABLELENGTH 1.5 m, 3-WIRE CABLE
DIMENSIONS SOLUTIONS FOR PROGRAMMING
THE PALMTOP PROGRAMMER FOR TUBULAR MOTORS WITH DRY CONTACT CABLE OR TTBUS.TTPRO
PORTABLE RADIO TRANSMITTER TO MANAGE UP TO 6 AUTOMATION GROUPS.ERA P SERIES
WALL-MOUNTED RADIO TRANSMITTER TO MANAGE UP TO 6 AUTOMATION GROUPS.SERIE ERA W
WALL-MOUNTED TOUCHLESS RADIO TRANSMITTER FOR CONTROLLING ONE AUTOMATION OR AUTOMATION GROUP.AIR
MULTIFUNCTION RADIO TRANSMITTER TO MANAGE UP TO 99 DEVICES INDIVIDUALLY OR IN GROUPS.ERA P VIEW
PORTABLE TRANSMITTER TO CONTROL LIGHTS, INTERIOR AND EXTERIOR BLINDS, ROLLER SHUTTERS AND ELECTRICAL LOADS.AGIO
SOLUTIONS FOR ADVANCED BUILDING MANAGEMENT
CONTROL SYSTEMS
MODULAR SYSTEMINTERFACE SYSTEMS, CONNECTION AND POWER MODULES, EACH WITH A SPECIFIC FUNCTION, COMBINED AND INSTALLED ON A DIN RAIL.
MYNICE WORLD APPTHROUGH THE DMBM MODULE, ALLOWS AUTOMATIONS FOR INTERIOR AND EXTERIOR BLINDS AND ROLLER SHUTTERS TO BE CONTROLLED LOCALLY OR REMOTELY VIA SMARTPHONE.
TECHNICAL SPECIFICATIONCODEELECTRICAL SPECIFICATIONSPOWER SUPPLY (VAC/Hz)CURRENT DRAW (A)POWER (W)POWER CONSUMPTION IN STANDBY (W)PERFORMANCETORQUE (Nm)RATED SPEED (rpm)MAXIMUM SPEED (rpm)MINIMUM SPEED (rpm)NOISE (dBA)**NUMBER OF TURNS BEFORE STOPPINGCONTINUOUS OPERATING TIME (MIN)LIFTED WEIGHT (kg)***DIMENSIONAL DATALENGTH (L) (mm)CABLE LENGTH (m)WEIGHT OF MOTOR (kg)OPERATING TEMP. (°C MIN/MAX) PACK DIMENSIONS (mm)
Protection class IP30.*if the set speed is higher than the rated speed, motor torque is automatically reduced by 50%.**Noise levels have been measured in accordance with EN ISO 3745, EN ISO 3746 and EN 60704-1, expressing the sound power emitted by the source in dBA.***Indicative value calculated with a 40 mm diameter roller. The actual value may vary depending on the specific installation.
PHASE NEUTRALEARTH
Ø 52
9
2
2
Ø 53
12,5
8
21,8
12
6
6
Ø 65 Ø 65
1,8
16 6,6
6,4 6,5
14,5
7,4 2,5
6,6
6,5
16
7,4
14,5
7,2
Ø 80
COM
PATI
BLE
ADAP
TERS
TYPE
OF
ROLL
ER P
RESE
NT IN
THE
SYST
EM
503.15000 513.15200 503.15300 503.15301 513.16300 513.16501 513.18000 503.24000Notch 50x2 wheel + crown
Notch 52x2 Benthinwheel + crown
Notch 53x1.5 wheel + crown
Notch 53x2wheel + crown
Notch 65x1.8wheel + crown
Notch 65x1.8 Coulissewheel + crown
Notch 80x2.5 Coulissewheel + crown
Round 40x1 wheel + crown
ROUND 50 WITH SPECIAL NOTCH NOTCH 52 BENTHIN ROUND 53 WITH SPECIAL NOTCH NOTCH 53 NOTCH 65 / ROLLEASE NOTCH 65 COULISSE NOTCH 80 COULISSE ROUND 40
ADAPTERS - ERA INN S SERIES 35 mm
Ø 46
Ø 44
7,8
8 6
9 3,6
3,9
1,3
Ø 53
1,5
4,8
6,6
(1x)
5,2 (3x)
5,2 (3x)
6,6
(1x)
8,5
TONDO 42 COULISSE
Ø 42
2,4
1,5
OGIVA 50 COULISSE
Ø 50
6,4
1,5
Ø 44
1,5
3
Ø 46
Ø 44
7,8
8 6
9 3,6
3,9
1,3
Ø 53
1,5
4,8
6,6
(1x)
5,2 (3x)
5,2 (3x)
6,6
(1x)
8,5
TONDO 42 COULISSE
Ø 42
2,4
1,5
OGIVA 50 COULISSE
Ø 50
6,4
1,5
Ø 46
Ø 44
7,8
8 6
9 3,6
3,9
1,3
Ø 53
1,5
4,8
6,6
(1x)
5,2 (3x)
5,2 (3x)
6,6
(1x)
8,5
COM
PATI
BLE
ADAP
TERS
TYPE
OF
ROLL
ER P
RESE
NT IN
THE
SYST
EM
513.24000 503.24115 503.24315 513.24200 513.24401 503.24500 503.24615
Round 40x(1.4÷2) wheel + crown
Round 44x3.5 wheel + crown
Round with ribbing and 37 inner size wheel + crown
Round 42x1.5 Coulissewheel + crown
Round 44x1.5 Benthinwheel + crown
ZF45wheel + crown
Notch 45x4 wheel + crown
ROUND 40 ROUND 44 ROUND 44 ROUND 42 COULISSE ROUND 44 BENTHIN ZF45 ROUND 45
ROUND 44 WITH SPECIAL NOTCH ROUND 46 NOTCH 50 COULISSE
ROUND 53
3,2 1,7
Ø 5010,7
6,3
Ø 49
1,8
17,66
1,85
Ø 53,7 Ø 60
7
2
17
4,2
6,8 10,5 1,5
Ø 61
64
10
503.25000 503.25001 503.25003 503.25300 503.26000 503.26200 503.26201
Round 50x1.5wheel + crown
Round 50x1.7 Rollease (Roller 2.00K)wheel + crown
Round 45x1.8 Acmeda with inner ribbing wheel + crown
Notch 53x1.5 Hunter Douglas wheel + crown
Notch 60x2 Acmedawheel + crown
Round 63x1.5 (Welser) - 62x0.6 (Deprat) wheel + crown
Oval with notch 61-64x1.5wheel + crown
ROUND 50 ROUND 50 ROLLEASE ROUND 49 ACMEDA NOTCH 53 HUNTER DOUGLAS NOTCH 60 ACMEDA ROUND 63 OVAL 61/64
NOTCH WELSER 63
DEPRAT 62
COM
PATI
BLE
ADAP
TERS
TYPE
OF
ROLL
ER P
RESE
NT IN
THE
SYST
EMADAPTERS - ERA INN S SERIES 35 mm
V4x10
29
29
Ø4
8
Ø5
6,4
Ø43
26
26
63
24 20
63
59
38,5
8,5 7,5 8,52
V4x10
89
7,56
33
6
54
87,5
33
897,5
37 37
Ø38
29
Ø4
36
36
Ø10
R 5,5
50,5
50,5
65 3
13,4
13,4
SUPPORTS - ERA INN S SERIES 35 mm
523.40001
White support kit with flange, centre distance 40 mm, for 35 mm motors and 48 mm Acmeda roller.
525.40001
White support kit, centre distance 55 mm, for 35 mm motors, max 3 Nm. Must be used together with cap kit 575.24801, 575.26000 or 575.25000.
SUPPORT KIT
V4x10
89
7,56
54
33
89
7,5
37 37
36
36
Ø10
R 5,5
50,5
65 2
29
48
38
58
36
36R 5,5
6
87,5
33
Ø4
50,5
Ø4
Ø 43
52
41
Ø 50
52
46
525.40003
White support kit, centre distance 55 mm, for 35/45 mm motors, max 10 Nm. Must be used together with cap kit 575.24801, 575.26000, 575.25000, 575.26300.
SUPPORTS - ERA INN S SERIES 35 mm
575.24801
White cap kit for 48 mm Acmeda roller, for 35 mm motors.Must be combined with the white support kit, centre distance 55 mm for 35 mm motors 525.40001 or 525.40003.
575.25000
White cap kit for 2'' (50 mm) Rollease roller, for 35 mm and 45 mm motors. Must be combined with the white support kit, centre distance 55 mm, for 35/45 mm motors 525.40001 or 525.40003.
SUPPORT KIT CAP KIT
26
9
20
60
38
Ø 3
2
Ø 15
33
88
Ø 3
2
53
9
Ø 15
50,5
Ø 43
68,59
Ø 5
8
65
Ø48
Ø29 8013
30
13
Ø6,5
Ø4,2Ø40
13,5
8
Ø29
2
Ø4
Ø 3
,5
29
62
Ø 1
2
523.40002
Intermediate white support, centre distance 40 mm, for 35 mm motors.Must be used together with cap kit 575.24800.
525.40004
Intermediate white support, centre distance 55 mm, for 35/45 mm motors. Must be combined with the intermediate cap kit 575.24800.
525.10075
White support with 4 countersunk holes.
523.10015
Circular support with cross hole.
525.10070
Kit for vertical blinds, white (for use with 575.12040 or 575.12050).
575.12040
Cap with pin for Ø 40 mm roller.
575.12050
Cap with pin for Ø 50 mm roller.
INTERMEDIATE SUPPORTS
OTHER SUPPORTS
575.24800
Intermediate white cap kit for 48 mm Acmeda roller, for 35 mm motors. Must be combined with the intermediate supports 523.40002 or 525.40004.
Motor side
Hole for cap with Ø 6 mm pin
Cap side
523.00000
White head adapter compatible with star head universal motor supports (centre distance 29 mm).
575.12045
575.16045
523.10018
575.17045
523.20018523.30018
523.18045
6,3
Ø 49
1,8
Ø 60
7
2
17
4,2
6,8
COMPATIBLE ADAPTERS AND SUPPORTS - ERA INN S SERIES 35 mmACMEDA
523.40003
White support kit for Acmeda S45 rollers.
The kit comprises:
CODE DESCRIPTION
575.12045 Cap with retractable pin for Acmeda S45 rollers 523.10018 White bracket kit with flange for Acmeda S45 rollers 523.30018 White cover kit for brackets for Acmeda S45 rollers523.20018 White adapter disk with cross hole for Acmeda S45 rollers
523.40004
Intermediate white support kit for Acmeda S45 rollers.
The kit comprises:
CODE DESCRIPTION
575.16045 Intermediate white cap (male) for Acmeda S45 rollers575.17045 Intermediate white cap (female) for Acmeda S45 rollers523.18045 Intermediate white support for Acmeda S45 rollers
503.25003 503.26000
Round 45x1.8 Acmeda with inner ribbing wheel + crown
Notch 60x2 Acmedawheel + crown
ROUND 49 ACMEDA NOTCH 60 ACMEDA
COM
PATI
BLE
ADAP
TERS
TYPE
OF
ROLL
ER P
RESE
NT IN
THE
SYST
EM
3,2 1,7
Ø 5010,7
1,8
12
6
6
Ø 65 Ø 44
1,5
3
Ø 52
9
2
2
TONDO 42 COULISSE
Ø 42
2,4
1,5
OGIVA 50 COULISSE
Ø 50
6,4
1,5
Ø 65
1,8
16 6,6
6,4 6,5
14,5
7,4 2,5
6,6
6,5
16
7,4
14,5
7,2
Ø 80
TONDO 42 COULISSE
Ø 42
2,4
1,5
OGIVA 50 COULISSE
Ø 50
6,4
1,5
Ø 4
38
29
23,7
29
29Ø 38
Ø 4
BENTHINROLLEASE COULISSE
513.24401 513.15200Round 44x1.5 Benthinwheel + crown
Notch 52x2 Benthinwheel + crown
ROUND 44 BENTHIN NOTCH 52 BENTHIN
513.24200 513.16501 513.18000Round 42x1.5 Coulissewheel + crown
Notch 65x1.8 Coulissewheel + crown
Notch 80x2.5 Coulissewheel + crown
ROUND 42 COULISSE NOTCH 65 COULISSE NOTCH 80 COULISSE
NOTCH 50 COULISSE
COM
PATI
BLE
ADAP
TERS
TYPE
OF
ROLL
ER P
RESE
NT IN
THE
SYST
EM
NB: Nice Era Inn size S 35 mm motors are compatible with the Acmeda/Rollease/Coulisse/Benthin supports adaptable to suit these sizes. For the technical specifications see the manufacturer’s catalogue.
523.30000
White universal adapter for Coulisse supports (centre distance 29 mm).
523.30002
White head adapter for Rollease Skyline series supports (centre distance 29 mm).
523.30001
White head adapter for Rollease R8 series supports (centre distance 29 mm).
503.25001 513.16300
Round 50 Rollease (Roller 2.00K)wheel + crown
Notch 65x1.8wheel + crown
ROUND 50 NOTCH 65 / ROLLEASE
TECHNOLOGY AS SIMPLE AS A GESTURE
Nice cares for the environment.Using natural paper it avoids excessive use of raw materials and forest exploitation.Waste is reduced, energy is savedand climate quality is improved.
NICE, EASY SOLUTIONS FOR HOME AND BUILDING.
AUTOMATION AND CONTROL SYSTEMS FOR ROLLER BLINDS, AWNINGS, VENETIAN BLINDS, WINTERGARDEN, ROMAN AND PLEATED BLINDS, FOR INTERIOR AND EXTERIOR, ROLLING SHUTTERS, GATES, GARAGE DOORS AND ALARM SYSTEMS: PRACTICAL, FUNCTIONAL AND ELEGANT SOLUTIONS WITH INTEGRATED MANAGEMENT, TO ENJOY ANY LIVING SPACE TO THE FULL.
98.0
59/E
N •
The i
nfor
mat
ion sh
own i
n this
publ
icatio
n is p
urel
y ind
icativ
e. Ni
ce re
serv
es th
e righ
t to m
ake
mod
ifica
tions
to th
e pro
duct
s as i
t see
s fit P
rodu
ct D
esig
n Rob
erto
Ghe
rlend
a
Our products and our technologies are protected with patents, design models and brands. All violations will be prosecuted.
Nice SpAOderzo, Treviso - Italy
www.niceforyou.com