Upload
others
View
3
Download
1
Embed Size (px)
Citation preview
CD 500 HV FHD (ATEX)_Equipment Data Sheet (Rev 05) Page 1 of 2
Equipment Data Sheet: CD 500 HV FHD (ATEX) The CD 500 HV FHD is a Fully Variable - High Volume Centrifuge to be used on global drilling projects where the most efficient fluids/solids separation is required
Dimensions
Overall Dimensions & Weight
Weight 6,500 kg (14,330 lbs)
Length X 4,146 mm (163.23 in.)
Height Y 2,290 mm (90.16 in.)
Width Z 2,220 mm (87.40 in.)
Centre of Gravity Position
CG XG 2,032 mm (80.00 in.)
CG YG 856 mm (33.70 in.)
CG ZG 1,084 mm (42.68 in.)
Performances
G-Force & Feed Rate
Max Design Speed 3,400 rpm
Max Operating Speed 3,200 rpm
Max G-Force 2,656 G @ 3,200 rpm
Max Sigma Value 4,607 m2 (49,589 ft
2)
Hydraulic Capacity [TUV Certified]
153.1 m3/h (674 GPM)
Max Solids Discharge Rate
12.0 m3/h (53 GPM)
Physical Data
Rotating Assembly
Bowl Diameter (Internal) 472 mm (18.58 in.)
Bowl Length (Internal) 1,715 mm (67.52 in.)
Pond Setting 76 (R160) – 66 (R170) – 56 (R180) mm
(3.00 – 2.60 – 2.20 in.)
Bowl Material Stainless Steel Duplex A890
Bushings Protection Tungsten Carbide Solids Discharge Nozzle
Scroll Type Single Lead – Quasi Axial Flow
Scroll Pitch 130 mm (5.12 in.)
Scroll Angle 6°
Scroll Material Stainless Steel Duplex A890 - AISI 304
Flights Protection Scroll Fitted with Tungsten Carbide Tiles
Pillow Block Bearings Oil Forced Lubricated - Automatic
Internal Bearings Grease Lubricated - Manual
Feed Tube Open Ended – LGS Removal
Slotted – Barite Recovery
CD 500 HV SL VFD (ATEX)_Equipment Data Sheet (Rev 06) Page 1 of 2
Equipment Data Sheet: CD 500 HV SL VFD (ATEX) Slim Line, VFD ready - High Volume Centrifuge to be used on global drilling projects where the most efficient fluids/solids separation is required
Dimensions
Overall Dimensions & Weight
Weight 5,000 kg (11,023 lbs)
Length X 4,149 mm (163.35 in.)
Height Y 1,934 mm (76.14 in.)
Width Z 1,230 mm (48.43 in.)
Centre of Gravity Position
CG XG 2,126 mm (83.70 in.)
CG YG 1,147 mm (45.16 in.)
CG ZG 614 mm (24.17 in.)
Performances
G-Force & Feed Rate
Max Design Speed 3,400 rpm
Max Operating Speed 3,200 rpm
Max G-Force 2,656 G @ 3,200 rpm
Max Sigma Value 4,607 m2 (49,589 ft
2)
Hydraulic Capacity [TUV Certified]
153.1 m3/h (674 GPM)
Max Solids Discharge Rate
12.0 m3/h (53 GPM)
Physical Data
Rotating Assembly
Bowl Diameter (Internal) 472 mm (18.58 in.)
Bowl Length (Internal) 1,715 mm (67.52 in.)
Pond Setting 76 (R160) – 66 (R170) – 56 (R180) mm
(3.00 – 2.60 – 2.20 in.)
Bowl Material Stainless Steel Duplex A890
Bushings Protection Tungsten Carbide Solids Discharge Nozzle
Scroll Type Single Lead – Quasi Axial Flow
Scroll Pitch 130 mm (5.12 in.)
Scroll Angle 6°
Scroll Material Stainless Steel Duplex A890 - AISI 304
Flights Protection Scroll Fitted with Tungsten Carbide Tiles
Pillow Block Bearings Oil Forced Lubricated - Automatic
Internal Bearings Grease Lubricated - Manual
Feed Tube Open Ended – LGS Removal
Slotted – Barite Recovery
CD 500 HV SL VFD (ATEX)_Equipment Data Sheet (Rev 06) Page 2 of 2
Physical Data
Gearbox
Type Planetary Gearbox, Ratio 80:1
Max Output Torque 8,500 Nm (6,269 ft·lb)
Operating Differential 1 – 40 rpm
Drive & Operating System
Voltage 400/460 Volt, 50/60 Hz, 3 Phase - Standard
[690 Volt, 60 Hz, 3 Phase – Optional]
Main Drive Motor 75 kW (101 HP)
Back Drive Motor 22 kW (30 HP)
Control System PLC (Programmable Logic Controller)
Drive System VFD (Variable Frequency Drive)
Safety Features
Safety Devices
Torque Limiter to Protect Sun-wheel Shaft, Micro-switch on Vessel & Guards to Avoid
Start-up While Servicing, Main & Back Drive Motor Temperatures.
Display (Settings) Bowl Speed, Differential Value, Feed Rate, Current Adsorbed, Vibration, Bearings &
Feed Pump Stator Temperatures.
Automatic Safety System
Continuous Monitoring & Self Shutdown on All Critical Parameters. Automatic Control to Avoid Pack-off & Automatic Unplugging
Procedure.
Certification
Certification CE ATEX, Zone 1
Operating Temperature 0 +40°C (+32 +104 °F)
Storage Temperature -20 +40°C (-4 +104 °F)
Process Fluid Temperature Drilling Fluid: < 85°C (185°F)
Nozzle Schedule
Connection
Feed Pipe 2” ANSI B 16.5 Welding Neck
Liquid Discharge 8 in. Victaulic
Solids Discharge 810 x 450 mm (31.89 x 17.72 in.)
CD 600 VFD (ATEX)_Equipment Data Sheet (Rev 09) Page 1 of 2
Equipment Data Sheet: CD 600 VFD (ATEX) The CD 600 VFD is a Big Bowl VFD Ready Centrifuge which is specially engineered for high volume drilling, achievable of a high G Force at a low rpm
Dimensions
Overall Dimensions & Weight
Weight 7,600 kg (16,755 lbs)
Length X 4,256 mm (167.56 in.)
Height Y 1,219 mm (47.99 in.)
Width Z 2,367 mm (93.19 in.)
Centre of Gravity Dimensions
CG XG 2,117 mm (83.35 in.)
CG YG 598 mm (23.54 in.)
CG ZG 1,325 mm (52.17 in.)
Performances
G-Force & Feed Rate
Max Design Speed 2,800 rpm
Max Operating Speed 2,600 rpm
Max G-Force 2,229 G @ 2,600 rpm
Max Sigma Value 6,574 m2 (70,762 ft
2) @ 2,600 rpm
Hydraulic Capacity [TUV Certified]
179.7 m3/h (791 GPM)
Max Solids Discharge Rate
28.5 m3/h (125 GPM)
Physical Data
Rotating Assembly
Bowl Diameter (Internal) 598 mm (23.54 in.)
Bowl Length (Internal) 2,020 mm (79.53 in.)
Pond Setting 71 (R228) – 61 (R238) – 51 (R248) mm
(2.80 – 2.40 – 2.00 in.)
Bowl Material Stainless Steel Duplex A890
Bushings Protection Tungsten Carbide Solids Discharge Nozzle
Scroll Type Single Lead – Radial Flow
Scroll Pitch 150 mm (5.91 in.)
Scroll Angle 6°
Scroll Material Stainless Steel AISI 304
Flights Protection Scroll Fitted with Tungsten Carbide Tiles
Pillow Block Bearings Oil Forced Lubricated - Automatic
Internal Bearings Grease Lubricated - Manual
Feed Tube Open Ended – Axial Flow
CD 600 VFD (ATEX)_Equipment Data Sheet (Rev 09) Page 2 of 2
Physical Data
Gearbox
Type Planetary Gearbox, Ratio 80:1
Max Output Torque 11,000 Nm (8,113 ft·lb)
Operating Differential 1 – 40 rpm
Drive & Operating System
Voltage 400/460 Volt, 50/60 Hz, 3 Phase - Standard
[690 Volt, 60 Hz, 3 Phase - Optional]
Main Drive Motor 90 kW (121 HP)
Back Drive Motor 30 kW (140 HP)
Control System PLC (Programmable Logic Controller)
Drive System VFD (Variable Frequency Drive)
Safety Features
Safety Devices
Torque Limiter to Protect Sun-wheel Shaft, Micro-switch on Vessel & Guards to Avoid
Start-up While Servicing, Main & Back Drive Motor Temperatures.
Display (Settings) Bowl Speed, Differential Value, Feed Rate, Current Adsorbed, Vibration, Bearings &
Feed Pump Stator Temperatures.
Automatic Safety System
Continuous Monitoring & Self Shutdown on All Critical Parameters. Automatic Control to Avoid Pack-off & Automatic Unplugging
Procedure.
Certification
Certification CE ATEX, Zone 1
Operating Temperature 0 +40°C (+32 +104 °F)
Storage Temperature -20 +40°C (-4 +104 °F)
Process Fluid Temperature Drilling Fluid: < 85°C (185°F)
Nozzle Schedule
Connection
Feed Pipe 2-1/2” ANSI B 16.5 Welding Neck
Liquid Discharge 3 x Custom Design Flanges
Standard Supply 2 x 8 in. + 1 Blind Flange
Solids Discharge 1,020 x 474 mm (40.16 x 18.66 in.)
CD 600 SL FHD (ATEX)_Equipment Data Sheet (Rev 06) Page 1 of 2
Equipment Data Sheet: CD 600 SL FHD (ATEX) The CD 600 SL FHD is a Big Bowl (Fully Variable) Centrifuge which is specially engineered for high volume drilling, achievable of a high G Force at a low rpm
Dimensions
Overall Dimensions & Weight – Centrifuge Module
Weight 7,000 kg (15,432 lbs)
Length X 4,479 mm (176.34 in.)
Height Y 1,809 mm (71.22 in.)
Width Z 1,460 mm (57.48 in.)
Overall Dimensions & Weight – Hydraulic Module
Weight 4,000 kg (8,819 lbs)
Length X 3,735 mm (147.05 in.)
Height Y 2,095 mm (82.48 in.)
Width Z 1,500 mm (59.06 in.)
Performances
G-Force & Feed Rate
Max Design Speed 2,800 rpm
Max Operating Speed 2,600 rpm
Max G-Force 2,229 G @ 2,600 rpm
Max Sigma Value 6,574 m2 (70,762 ft
2)
Hydraulic Capacity [TUV Certified]
179.7 m3/h (791 GPM)
Max Solids Discharge Rate
28.5 m3/h (125 GPM)
Physical Data
Rotating Assembly
Bowl Diameter (Internal) 598 mm (23.54 in.)
Bowl Length (Internal) 2,020 mm (79.53 in.)
Pond Setting 71 (R228) – 61 (R238) – 51 (R248) mm
(2.80 – 2.40 – 2.00 in.)
Bowl Material Stainless Steel Duplex A890
Bushings Protection Tungsten Carbide Solids Discharge Nozzle
Scroll Type Single Lead – Radial Flow
Scroll Pitch 150 mm (5.91 in.)
Scroll Angle 6°
Scroll Material Stainless Steel AISI 304
Flights Protection Scroll Fitted with Tungsten Carbide Tiles
Pillow Block Bearings Oil Forced Lubricated – Automatic
Internal Bearings Grease Lubricated – Manual
Feed Tube Open Ended – Axial Flow
CD 600 SL FHD (ATEX)_Equipment Data Sheet (Rev 06) Page 2 of 2
Physical Data
Gearbox
Type Planetary Gearbox, Ratio 80:1
Max Output Torque 11,000 Nm (8,113 ft·lb)
Operating Differential 1 – 40 rpm
Drive & Operating System
Voltage 400/460 Volt, 50/60 Hz, 3 Phase - Standard
[690 Volt, 60 Hz, 3 Phase – Optional]
Drive Motor 132 kW (177 HP)
Control System PLC (Programmable Logic Controller)
Drive System Independent Fully Variable Main & Back
Hydraulic Motors; Fully Variable Feed Rate
Safety Features
Safety Devices Torque Limiter To Protect Sun-Wheel Shaft Micro-Switch On Vessel & Guards To Avoid
Start-Up While Servicing.
Display (Settings)
Bowl Speed, Differential Value, Feed Rate, Current Adsorbed, Vibration, Main Bearings & Hydraulic Oil Temperature, Main & Back
Drives Pressure.
Automatic Safety System
Continuous Monitoring & Self Shutdown On All Critical Parameters, Automatic Control To Avoid Pack-off & Automatic Unplugging
Procedure.
Certification
Certification CE ATEX, Zone 1
Operating Temperature 0 +40°C (+32 +104 °F)
Storage Temperature -20 +40°C (-4 +104 °F)
Process Fluid Temperature Drilling Fluid: < 85°C (185°F)
Nozzle Schedule
Connection
Feed Pipe 2-1/2” ANSI B 16.5 Welding Neck
Liquid Discharge 1 x 10 in. (UNI 2277-67 PN10)
Solids Discharge 1,020 x 474 mm (40.16 x 18.66 in.)
CD 600 FHD (ATEX)_Equipment Data Sheet (Rev 06) Page 1 of 2
Equipment Data Sheet: CD 600 FHD (ATEX) The CD 600 FHD is a Big Bowl (Fully Variable) Centrifuge which is specially engineered for high volume drilling, achievable of a high G Force at a low rpm
Dimensions
Overall Dimensions & Weight
Weight 9,000 kg (19,842 lbs)
Length X 4,586 mm (180.55 in.)
Height Y 2,095 mm (82.48 in.)
Width Z 2,210 mm (87.01 in.)
Centre of Gravity Dimensions
CG XG 2,250 mm (88.58 in.)
CG YG 659 mm (25.95 in.)
CG ZG 1,122 mm (44.17 in.)
Performances
G-Force & Feed Rate
Max Design Speed 2,800 rpm
Max Operating Speed 2,600 rpm
Max G-Force 2,229 G @ 2,600 rpm
Max Sigma Value 6,574 m2 (70,762 ft
2)
Hydraulic Capacity [TUV Certified]
179.7 m3/h (791 GPM)
Max Solids Discharge Rate
28.5 m3/h (125 GPM)
Physical Data
Rotating Assembly
Bowl Diameter (Internal) 598 mm (23.54 in.)
Bowl Length (Internal) 2,020 mm (79.53 in.)
Pond Setting 71 (R228) – 61 (R238) – 51 (R248) mm
(2.80 – 2.40 – 2.00 in.)
Bowl Material Stainless Steel Duplex A890
Bushings Protection Tungsten Carbide Solids Discharge Nozzle
Scroll Type Single Lead – Radial Flow
Scroll Pitch 150 mm (5.91 in.)
Scroll Angle 6°
Scroll Material Stainless Steel AISI 304
Flights Protection Scroll Fitted with Tungsten Carbide Tiles
Pillow Block Bearings Oil Forced Lubricated - Automatic
Internal Bearings Grease Lubricated - Manual
Feed Tube Open Ended – Axial Flow
CD 600 FHD (ATEX)_Equipment Data Sheet (Rev 06) Page 2 of 2
Physical Data
Gearbox
Type Planetary Gearbox, Ratio 80:1
Max Output Torque 11,000 Nm (8,113 ft·lb)
Operating Differential 1 – 40 rpm
Drive & Operating System
Voltage 400/460 Volt, 50/60 Hz, 3 Phase - Standard
[690 Volt, 60 Hz, 3 Phase – Optional]
Drive Motor 132 kW (177 HP)
Control System PLC (Programmable Logic Controller)
Drive System Independent Fully Variable Main & Back
Hydraulic Motors; Fully Variable Feed Rate
Safety Features
Safety Devices Torque Limiter To Protect Sun-Wheel Shaft Micro-Switch On Vessel & Guards To Avoid
Start-Up While Servicing.
Display (Settings)
Bowl Speed, Differential Value, Feed Rate, Current Adsorbed, Vibration, Hydraulic Oil Temperature & Pressures, Bearings & Feed
Pump Stator Temperatures.
Automatic Safety System
Continuous Monitoring & Self Shutdown on All Critical Parameters, Automatic Control to Avoid Pack-off & Automatic Unplugging
Procedure.
Certification
Certification CE ATEX, Zone 1
Operating Temperature 0 +40°C (+32 +104 °F)
Storage Temperature -20 +40°C (-4 +104 °F)
Process Fluid Temperature Drilling Fluid: < 85°C (185°F)
Nozzle Schedule
Connection
Feed Pipe 2-1/2” ANSI B 16.5 Welding Neck
Liquid Discharge 3 x Custom Design Flanges
Standard Supply 2 x 8 in. + 1 Blind Flange
Solids Discharge 1,020 x 474 mm (40.16 x 18.66 in.)
CD 500 HV VFD (ATEX)_Equipment Data Sheet (Rev 06) Page 1 of 2
Equipment Data Sheet: CD 500 HV VFD (ATEX) Low Profile, VFD ready High Volume Centrifuge to be used on global drilling projects where the most efficient fluids/solids separation is required
Dimensions
Overall Dimensions & Weight
Weight 5,000 kg (11,023 lbs)
Length X 3,946 mm (155.35 in.)
Height Y 1,215 mm (47.83 in.)
Width Z 2020 mm (79.53 in.)
Centre of Gravity Position
CG XG 1,994 mm (78.50 in.)
CG YG 539 mm (21.22 in.)
CG ZG 1,074 mm (42.28 in.)
Performances
G-Force & Feed Rate
Max Design Speed 3,400 rpm
Max Operating Speed 3,200 rpm
Max G-Force 2,656 G @ 3,200 rpm
Max Sigma Value 4,607 m2 (49,589 ft
2)
Hydraulic Capacity [TUV Certified]
153.1 m3/h (674 GPM)
Max Solids Discharge Rate
12.0 m3/h (53 GPM)
Physical Data
Rotating Assembly
Bowl Diameter (Internal) 472 mm (18.58 in.)
Bowl Length (Internal) 1,715 mm (67.52 in.)
Pond Setting 76 (R160) – 66 (R170) – 56 (R180) mm
(3.00 – 2.60 – 2.20 in.)
Bowl Material Stainless Steel Duplex A890
Bushings Protection Tungsten Carbide Solids Discharge Nozzle
Scroll Type Single Lead – Quasi Axial Flow
Scroll Pitch 130 mm (5.12 in.)
Scroll Angle 6°
Scroll Material Stainless Steel Duplex A890 - AISI 304
Flights Protection Scroll Fitted with Tungsten Carbide Tiles
Pillow Block Bearings Oil Forced Lubricated - Automatic
Internal Bearings Grease Lubricated - Manual
Feed Tube Open Ended – LGS Removal
Slotted – Barite Recovery
CD 500 HV VFD (ATEX)_Equipment Data Sheet (Rev 06) Page 2 of 2
Physical Data
Gearbox
Type Planetary Gearbox, Ratio 80:1
Max Output Torque 8,500 Nm (6,269 ft·lb)
Operating Differential 1 – 40 rpm
Drive & Operating System
Voltage 400/460 Volt, 50/60 Hz, 3 Phase - Standard
[690 Volt, 60 Hz, 3 Phase – Optional]
Main Drive Motor 75 kW (101 HP)
Back Drive Motor 22 kW (30 HP)
Control System PLC (Programmable Logic Controller)
Drive System VFD (Variable Frequency Drive)
Safety Features
Safety Devices
Torque Limiter to Protect Sun-wheel Shaft, Micro-switch on Vessel & Guards to Avoid
Start-up While Servicing, Main & Back Drive Motor Temperatures.
Display (Settings) Bowl Speed, Differential Value, Feed Rate, Current Adsorbed, Vibration, Bearings &
Feed Pump Stator Temperatures.
Automatic Safety System
Continuous Monitoring & Self Shutdown on All Critical Parameters. Automatic Control to Avoid Pack-off & Automatic Unplugging
Procedure.
Certification
Certification CE ATEX, Zone 1
Operating Temperature 0 +40°C (+32 +104 °F)
Storage Temperature -20 +40°C (-4 +104 °F)
Process Fluid Temperature Drilling Fluid: < 85°C (185°F)
Nozzle Schedule
Connection
Feed Pipe 2” ANSI B 16.5 Welding Neck
Liquid Discharge 8 in. Victaulic
Solids Discharge 810 x 450 mm (31.89 x 17.72 in.)
CD 500 HV FHD (ATEX)_Equipment Data Sheet (Rev 05) Page 2 of 2
Physical Data
Gearbox
Type Planetary Gearbox, Ratio 80:1
Max Output Torque 8,500 Nm (6,269 ft·lb)
Operating Differential 1 – 40 rpm
Drive & Operating System
Voltage 400/460 Volt, 50/60 Hz, 3 Phase - Standard
[690 Volt, 60 Hz, 3 Phase – Optional]
Drive Motor 90 kW (121 HP)
Control System PLC (Programmable Logic Controller)
Drive System Independent Fully Variable Main & Back
Hydraulic Motors; Fully Variable Feed Rate
Safety Features
Safety Devices Torque Limiter to Protect Sun-wheel Shaft, Micro-switch on Vessel & Guards to Avoid
Start-up While Servicing.
Display (Settings)
Bowl Speed, Differential Value, Feed Rate, Current Adsorbed, Vibration, Hydraulic Oil Temperature & Pressures, Bearings & Feed
Pump Stator Temperatures.
Automatic Safety System
Continuous Monitoring & Self Shutdown on All Critical Parameters, Automatic Control to Avoid Pack-off & Automatic Unplugging
Procedure.
Certification
Certification CE ATEX, Zone 1
Operating Temperature 0 +40°C (+32 +104 °F)
Storage Temperature -20 +40°C (-4 +104 °F)
Process Fluid Temperature Drilling Fluid: < 85°C (185°F)
Nozzle Schedule
Connection
Feed Pipe 2” ANSI B 16.5 Welding Neck
Liquid Discharge 8 in. Victaulic
Solids Discharge 810 x 450 mm (31.89 x 17.72 in.)