EN Solid Carbide Tools Catalog

PPRREECCIISSIIOONN SSOOLLIIDD

CCAARRBBIIDDEE MMIICCRROOTTOOOOLLSS

2012.

FrezyCNC.eu FrezyCNC.pl CNCtools.eu

TABLE OF CONTENTS

Jewelry

PCB

Signage

SRD

End‐Mills 3 - 1 5 DeepReach 2‐flute, fish tail ________________________________ 3 DeepReach 2‐flute, ball nose _______________________________ 3 DeepReach 3‐flute, fish tail ________________________________ 4 DeepReach 3‐flute, ball nose _______________________________ 4 Ultra 3‐flute, fish tail _____________________________________ 5 Pro 2‐flute, fish tail ______________________________________ 6 Pro 2‐flute, ball nose _____________________________________ 7 Pro Metal 2‐flute stub, fish tail _____________________________ 8 Pro Metal 2‐flute stub, ball nose ____________________________ 9 ProMetric 2‐flute, fish tail ________________________________ 10 ProMetric 2‐flute, V‐drill point ____________________________ 11 ProMetric 1‐flute, V‐drill point ____________________________ 12 Pro 3‐flute, fish tail _____________________________________ 15

End‐Mills/Down‐Cut (left flute) 1 3 - 1 4

Pro 2‐flute left, fish tail __________________________________ 13 ProMetric 2‐flute left, fish tail _____________________________ 14

Carving Tools 1 3 - 1 3 Pro 4‐flute tapered, ball nose _____________________________ 13

Drill Bits 1 6 - 2 2

Pro Drill Bits 2‐flute 28°, drill point ______________________ 16‐17 ProMetric Drill Bits 2‐flute 35/30° UC, drill point ___________ 18‐19 ProMetric Drill Bits 2‐flute 30° ST, drill point ______________ 19‐21 ProMetric Slot Drill Bits 2‐flute 30° SL, drill point _____________ 22

Router Bits 2 3 - 2 6

Diamond Cut, fish tail ___________________________________ 23 Diamond Cut M30°, fish tail _______________________________ 24 Chip Breaker, fish tail ____________________________________ 25 Chip Breaker M20°, fish tail _______________________________ 26

Engraving Tools 2 7 - 2 8 Pro Engraving 1‐flute, V‐tip ______________________________ 27 Pro Engraving 2‐flute, V‐tip _______________________________ 27 Pro Engraving 4‐flute, V‐tip _______________________________ 28 Ultra Engraving 2‐flute, V‐tip ______________________________ 28

Specialty Tools 2 9 - 2 9

Ultra 2‐flute Ivory/Horn cutter, fish tail _____________________ 29 Ultra 3‐flute Shell cutter, fish tail __________________________ 29

Steel Rule Dies 3 0 - 3 2

Ultra 5‐flute Kerf cutters, fish tail __________________________ 30 Ultra 2‐flute CounterBoard, V‐tip __________________________ 31 Pro 3‐flute CounterBoard Channel, fish tail __________________ 31 Pro 4‐flute CounterBoard, V‐tip ___________________________ 32

Collets / Nuts / Toolholders 3 5 - 3 7 ER Spring Collets _______________________________________ 33 ER Collet Nuts _________________________________________ 33 ISO 20 ER Collet Toolholders ______________________________ 34 Porter‐Cable, Bosch 1618, Bosch Colt Collets / Nuts ________ 35‐37

©© 22001122 II nn GGrr aapphh // FFrr eezz yyCCNNCC.. eeuu FFrr eezz yyCCNNCC.. ppll CCNNCCtt ooooll ss.. eeuu

UUppddaa tt eedd:: JJ aannuuaa rr yy 22001122

InGraph [email protected] P a g e | 3

DeepReach, 2-flute, fish tail, end-mill – shank 3,18 mm & 6,35 mm

Specifications: Benefits: End‐M

ills

Geometry – 2 flute, fish tail Overall Length – OAL – nominal ±0.25 mm Flute dia – d – nominal +0.00 -0.02 mm

Shank dia – D – nominal +0.00 -0.002 mm Runout – TIR – max. 0.005 mm Depth Of Cut – DOC – nominal ±0.10 mm

Anticipated Life: depends on material being cut blue or green jeweler's wax - min. 500 rm

western red cedar - min. 250 rm acrylic - min. 80 rm

Material – solid submicrograin carbide

Operating CNC – 1k÷60k RPM Country of Origin – USA

Fish tail point eliminates backside breakout and splintering High flute volume supports high feed rates / chip loads High aspect ratio for deep single-pass cutting

Flute geometry optimized for cutting sign foam, sign board, hardwoods, thermoplastics, and phenolic composites

DeepReach design optimized for high-relief carving

Applications: Dimensional signage 3D countouring Cabinetry, furniture making

Jewelry mold making 3D modeling and pattern making Steel rule die blankers and strippers

Item# Flute Dia. ‐ d Shank Dia. ‐ D D‐h of Cut Length ‐ OAL Price* 10‐pack*

DF208‐0025‐0152‐M 0.25 mm (.0100”) 3.18mm (1/8”) 1.52 mm 38.10 mm 20,31 € 184,83 €

DF208‐0046‐0292‐M 0.46 mm (.0180”) 3.18mm (1/8”) 2.92 mm 38.10 mm 17,12 € 155,78 €

DF208‐0051‐0318‐M 0.51 mm (.0200”) 3.18mm (1/8”) 3.18 mm 38.10 mm 16,02 € 145,75 €

DF208‐0080‐0660‐M 0.80 mm (.0313”) 3.18mm (1/8”) 6.60 mm 38.10 mm 10,64 € 96,82 €

DF208‐0159‐1270‐M 1.59 mm (.0625”) 3.18mm (1/8”) 12.70 mm 38.10 mm 10,01 € 91,12 €

DF208‐0318‐3175‐M 3.18 mm (.1250”) 3.18mm (1/8”) 31.75 mm 76.20 mm 27,44 € ‐

DF204‐0635‐3810‐M 6.35 mm (.2500”) 6.35mm (1/4”) 38.10 mm 76.20 mm 27,44 € ‐

DF204‐0635‐3810‐ML 6.35 mm (.2500") 6.35mm (1/4”) 38.10 mm 101.60 mm 30,93 € ‐

**AAll ll pprriicceess aarree iinn EEUURR ((€)

DeepReach, 2-flute, ball nose, end-mill – shank 3,18 mm & 6,35 mm


ills

Geometry – 2 flute, ball nose

Overall Length – OAL – nominal ±0.25 mm Flute dia – d – nominal +0.00 -0.02 mm Shank dia – D – nominal +0.00 -0.002 mm

Runout – TIR – max. 0.005 mm Depth Of Cut – DOC – nominal ±0.10 mm Anticipated Life:

depends on material being cut blue or green jeweler's wax - min. 500 rm western red cedar - min. 250 rm acrylic - min. 80 rm

Material – solid submicrograin carbide Operating CNC – 1k÷60k RPM Country of Origin – USA

Ball-nose tip eliminates stair-stepping in 3D contour cuts

High flute volume supports high feed rates / chip loads High aspect ratio for deep single-pass cutting Flute geometry optimized for cutting sign foam, sign board,

hardwoods, thermoplastics, and phenolic composites DeepReach design optimized for high-relief carving

Applications: Dimensional signage

Large scale 3D carving 3D countouring and profiling Cabinetry, furniture making

Jewelry mold making 3D modeling and pattern making 3D millwork

Item# Coating Flute Dia. ‐ d Shank Dia. ‐ D D‐h of Cut Length ‐ OAL Price* 10‐pack*

DF208‐0318‐1588‐K ‐ 3.18 mm (.1250”) 3.18mm (1/8”) 15.88 mm 38.10 mm 23,37 € 212,67 €

DF208‐0318‐3175‐K ‐ 3.18 mm (.1250”) 3.18mm (1/8”) 31.75 mm 76.20 mm 31,22 € ‐

DF204‐0635‐3810‐K ‐ 6.35 mm (.2500”) 6.35mm (1/4”) 38.10 mm 101.60 mm 41,40 € ‐

DF204‐0635‐3810‐KZ ZrN 6.35 mm (.2500”) 6.35mm (1/4”) 38.10 mm 101.60 mm 50,90 € ‐


FrezyCNC.eu FrezyCNC.pl CNCtools.eu 4 | P a g e

DeepReach, 3-flute, fish tail, end-mill – shank 3,18 mm (1/8”)

End‐M

ills

Specifications: Benefits: Geometry – 3 flute, fish tail

Overall Length – OAL – nominal ±0.25 mm Flute dia – d – nominal +0.00 -0.02 mm Shank dia – D – 3.175 mm +0.00 -0.002 mm


depends on material being cut blue or green jeweler's wax - min. 500 rm western red cedar - min. 250 rm acrylic - min. 80 rm


Fish tail point eliminates backside breakout and splintering

3-Flute design reduces resonance and chatter under high chip loads

High flute volume supports high feed rates / chip loads

High aspect ratio for deep single-pass cutting Flute geometry optimized for cutting sign foam, sign board,

hardwoods, thermoplastics, and phenolic composites


Applications: Dimensional signage 3D countouring

Cabinetry, furniture making Jewelry mold making 3D modeling and pattern making

Steel rule die blankers and strippers


DF308‐0051‐0318‐M 0.51 mm (.0200”) 3.18mm (1/8”) 3.18 mm 38.10 mm 19,22 € 174,89 €

DF308‐0100‐0635‐M 1.00 mm (.0394”) 3.18mm (1/8”) 6.35 mm 38.10 mm 11,19 € 101,84 €

DF308‐0159‐1270‐M 1.59 mm (.0625”) 3.18mm (1/8”) 12.70 mm 38.10 mm 12,02 € 109,36 €

DF308‐0318‐2540‐M 3.18 mm (.1250”) 3.18mm (1/8”) 25.40 mm 76.20 mm 28,45 € ‐

DF308‐0318‐3175‐M 3.18 mm (.1250”) 3.18mm (1/8”) 31.75 mm 76.20 mm 35,06 € ‐


DeepReach, 3-flute, ball nose, end-mill – shank 3,18 mm (1/8”)

End‐M

ills

Specifications: Benefits: Geometry – 3 flute, ball nose Overall Length – OAL – nominal ±0.25 mm

Flute dia – d – nominal +0.00 -0.02 mm Shank dia – D – 3.175 mm +0.00 -0.002 mm Runout – TIR – max. 0.005 mm

Depth Of Cut – DOC – nominal ±0.10 mm Anticipated Life:

depends on material being cut

blue or green jeweler's wax - min. 500 rm western red cedar - min. 250 rm acrylic - min. 80 rm


Ball-nose tip eliminates stair-stepping in 3D contour cuts 3-Flute design reduces resonance and chatter under high

chip loads High flute volume supports high feed rates / chip loads High aspect ratio for deep single-pass cutting



Applications: Dimensional signage Large scale 3D carving 3D countouring and profiling

Cabinetry, furniture making Jewelry mold making 3D modeling and pattern making

3D millwork


DF308‐0318‐3175‐K 3.18 mm (.1250”) 3.18mm (1/8”) 31.75 mm 76.20 mm 46,05 € ‐



Ultra, 3-flute, kerf cutters, fish tail, end-mill – shank 3,18 mm (1/8”)


ills

Geometry – 3 flute, fish tail

Overall Length – OAL – 38.10 mm ±0.25 mm Flute dia – d – nominal +0.00 -0.01 mm Shank dia – D – 3.175 mm +0.00 -0.005 mm

Helix angle – 28° Runout – TIR – max. 0.005 mm Depth Of Cut – DOC – nominal ±0.10 mm

Anticipated Life: depends on material - min. 200 rm (maple)

Material – solid submicrograin carbide Operating CNC – 20k÷100k RPM

Country of Origin – USA



High flute volume supports high feed rates / chip loads 3-Flute design brings the rigidity and precision of a stub

mill to a high-aspect ratio milling cutter


Cutting edge geometry tuned to all aspects of inlay pocket cutting and component shaping

Applications: Compatible with most materials used in inlay and

entarsia

Item# Flute Dia. ‐ d Shank Dia. ‐ D D‐h of Cut Length ‐ OAL Price* 10‐packs*

F3I8‐0040‐0152‐M 0.40 mm (.0156”) 3.18mm (1/8”) 1.52 mm 38.10 mm 17,77 € 161,66 €

F3I8‐0051‐0229‐M 0.51 mm (.0200”) 3.18mm (1/8”) 2.29 mm 38.10 mm 17,77 € 161,66 €

F3I8‐0056‐0229‐M 0.56 mm (.0220”) 3.18mm (1/8”) 2.29 mm 38.10 mm 17,77 € 161,66 €

F3I8‐0058‐0229‐M 0.58 mm (.0230”) 3.18mm (1/8”) 2.29 mm 38.10 mm 17,77 € 161,66 €

F3I8‐0064‐0254‐M 0.64 mm (.0250”) 3.18mm (1/8”) 2.54 mm 38.10 mm 10,54 € 95,87 €

F3I8‐0080‐0356‐M 0.80 mm (.0313”) 3.18mm (1/8”) 3.56 mm 38.10 mm 11,19 € 101,84 €

F3I8‐0080‐0432‐M 0.80 mm (.0313”) 3.18mm (1/8”) 4.32 mm 38.10 mm 10,54 € 95,87 €

F3I8‐0089‐0432‐M 0.89 mm (.0350”) 3.18mm (1/8”) 4.32 mm 38.10 mm 11,19 € 101,84 €

F3I8‐0119‐0508‐M 1.19 mm (.0469”) 3.18mm (1/8”) 5.08 mm 38.10 mm 10,54 € 95,87 €

F3I8‐0127‐0635‐M 1.27 mm (.0500”) 3.18mm (1/8”) 6.35 mm 38.10 mm 10,54 € 95,87 €

F3I8‐0142‐0635‐M 1.42 mm (.0560”) 3.18mm (1/8”) 6.35 mm 38.10 mm 10,54 € 95,87 €

F3I8‐0159‐0787‐M 1.59 mm (.0625”) 3.18mm (1/8”) 7.87 mm 38.10 mm 11,19 € 101,84 €

F3I8‐0318‐1270‐M 3.18 mm (.1250”) 3.18mm (1/8”) 12.70 mm 38.10 mm 12,02 € 109,36 €



Pro, 2-flute, fish tail, end-mill – shank 3,18 mm (1/8”)

End‐M

ills Specifications: Benefits:








High flute volume supports high feed rates / chip loads Cutting edge geometry virtually eliminates chatter at high

feed rates

Spiral geometry insures efficient debris removal Flute geometry enhances rigidity for more accurate, single

pass cutting at high chip loads

Compatible with ebony, rosewood and all other hardwoods Flute geometry optimized for cutting sign foam, sign board,



Applications: Cutting inlay pockets and shaping components

Shaping / routing hardwoods and softwoods Machining reconstituted minerals Machining and slotting composites General purpose soft media machining


F208‐0013‐0064‐M 0.13 mm (.0050”) 3.18mm (1/8”) 0.64 mm 38.10 mm 34,45 € 313,47 €

F208‐0018‐0071‐M 0.18 mm (.0070”) 3.18mm (1/8”) 0.18 mm 38.10 mm 25,52 € 232,20 €

F208‐0025‐0114‐M 0.25 mm (.0100”) 3.18mm (1/8”) 1.14 mm 38.10 mm 19,58 € 178,17 €

F208‐0030‐0130‐M 0.30 mm (.0120”) 3.18mm (1/8”) 1.30 mm 38.10 mm 18,92 € 172,21 €

F208‐0040‐0180‐M 0.40 mm (.0156”) 3.18mm (1/8”) 1.80 mm 38.10 mm 14,48 € 131,75 €

F208‐0046‐0255‐M 0.46 mm (.0180”) 3.18mm (1/8”) 2.55 mm 38.10 mm 17,12 € 155,78 €

F208‐0051‐0230‐M 0.51 mm (.0200”) 3.18mm (1/8”) 2.30 mm 38.10 mm 14,81 € 134,78 €

F208‐0064‐0255‐M 0.64 mm (.0250”) 3.18mm (1/8”) 2.55 mm 38.10 mm 12,40 € 112,82 €

F208‐0080‐0330‐M 0.80 mm (.0313”) 3.18mm (1/8”) 3.30 mm 38.10 mm 8,78 € 79,88 €

F208‐0089‐0430‐M 0.89 mm (.0350”) 3.18mm (1/8”) 4.30 mm 38.10 mm 8,78 € 79,88 €

F208‐0100‐0510‐M 1.00 mm (.0394”) 3.18mm (1/8”) 5.10 mm 38.10 mm 8,78 € 79,88 €

F208‐0119‐0505‐M 1.19 mm (.0469”) 3.18mm (1/8”) 5.05 mm 38.10 mm 8,78 € 79,88 €

F208‐0127‐0635‐M 1.27 mm (.0500”) 3.18mm (1/8”) 6.35 mm 38.10 mm 8,78 € 79,88 €

F208‐0159‐0505‐M 1.59 mm (.0625”) 3.18mm (1/8”) 5.05 mm 38.10 mm 9,33 € 84,89 €

F208‐0159‐0785‐M 1.59 mm (.0625”) 3.18mm (1/8”) 7.85 mm 38.10 mm 9,33 € 84,89 €

F208‐0200‐0965‐M 2.00 mm (.0787”) 3.18mm (1/8”) 9.65 mm 38.10 mm 9,33 € 84,89 €

F208‐0238‐0965‐M 2.38 mm (.0938”) 3.18mm (1/8”) 9.65 mm 38.10 mm 9,33 € 84,89 €

F208‐0238‐1345‐M 2.38 mm (.0938”) 3.18mm (1/8”) 13.45 mm 38.10 mm 10,51 € 95,61 €

F208‐0300‐1270‐M 3.00 mm (.1181”) 3.18mm (1/8”) 12.70 mm 38.10 mm 9,33 € 84,89 €

F208‐0318‐0635‐M 3.18 mm (.1250”) 3.18mm (1/8”) 6.35 mm 38.10 mm 9,33 € 84,89 €

F208‐0318‐1270‐M 3.18 mm (.1250”) 3.18mm (1/8”) 12.70 mm 38.10 mm 9,33 € 84,89 €

F208‐0318‐1588‐M 3.18 mm (.1250”) 3.18mm (1/8”) 15.88 mm 50.80 mm 10,59 € 96,39 €



Pro, 2-flute, ball nose, end-mill – shank 3,18 mm (1/8”)


ills

Geometry – 2 flute, ball nose






Ball nose tip provides step-free contour milling of 3D solid models

High flute volume supports high feed rates / chip loads Spiral geometry insures efficient debris removal

Cutting edge geometry virtually eliminates chatter at high feed rates


Applications: 3D countouring and profiling 3D modeling and pattern making

3D millwork Custom jewelry Engraving trophies, awards and medallions


F208‐0015‐0045‐K 0.15 mm (.0060”) 3.18mm (1/8”) 0.45 mm 38.10 mm 49,12 € 447,03 €

F208‐0025‐0075‐K 0.25 mm (.0100”) 3.18mm (1/8”) 0.75 mm 38.10 mm 41,48 € 377,44 €

F208‐0080‐0318‐K 0.80 mm (.0313”) 3.18mm (1/8”) 3.18 mm 38.10 mm 27,44 € 249,67 €

F208‐0102‐0500‐K 1.02 mm (.0400”) 3.18mm (1/8”) 5.00 mm 38.10 mm 27,44 € 249,67 €

F208‐0159‐0635‐K 1.59 mm (.0625”) 3.18mm (1/8”) 6.35 mm 38.10 mm 27,44 € 249,67 €

F208‐0238‐0953‐K 2.38 mm (.0938”) 3.18mm (1/8”) 9.53 mm 38.10 mm 19,70 € 179,30 €

F208‐0318‐1270‐K 3.18 mm (.1250”) 3.18mm (1/8”) 12.70 mm 38.10 mm 19,25 € 175,15 €



Pro Metal, 2-flute stub, fish tail, end-mill – shank 3,18 mm (1/8”)

End‐M

ills

Specifications: Benefits: Geometry – 2 flute stub, fish tail



Anticipated Life: depends on material - min. 150 rm (ebony)




High flute volume supports high feed rates / chip loads Cutting edge geometry virtually eliminates chatter at high feed

rates




Applications: Machining non-ferrous and precious metals for jewelry

fabrication Engraving plaques, signs and awards Shaping high mineral content reconstituted stone products

Cutting and shaping mild steels


MF208‐0002‐0004‐M 0.02 mm (.0010”) 3.18mm (1/8”) 0.04 mm 36.07 mm 43,81 € 398,71 €

MF208‐0005‐0008‐M 0.05 mm (.0020”) 3.18mm (1/8”) 0.08 mm 36.07 mm 36,50 € 332,14 €

MF208‐0008‐0013‐M 0.08 mm (.0030”) 3.18mm (1/8”) 0.13 mm 36.07 mm 31,46 € 286,32 €

MF208‐0010‐0023‐M 0.10 mm (.0040”) 3.18mm (1/8”) 0.23 mm 36.07 mm 27,37 € 249,06 €

MF208‐0013‐0025‐M 0.13 mm (.0050”) 3.18mm (1/8”) 0.25 mm 36.07 mm 25,40 € 231,17 €

MF208‐0018‐0038‐M 0.18 mm (.0070”) 3.18mm (1/8”) 0.38 mm 36.07 mm 25,40 € 231,17 €

MF208‐0020‐0041‐M 0.20 mm (.0080”) 3.18mm (1/8”) 0.41 mm 36.07 mm 25,40 € 231,17 €

MF208‐0025‐0051‐M 0.25 mm (.0100”) 3.18mm (1/8”) 0.51 mm 36.07 mm 18,91 € 172,12 €

MF208‐0030‐0064‐M 0.30 mm (.0120”) 3.18mm (1/8”) 0.64 mm 36.07 mm 18,91 € 172,12 €

MF208‐0038‐0064‐M 0.38 mm (.0150”) 3.18mm (1/8”) 0.64 mm 36.07 mm 14,49 € 131,84 €

MF208‐0046‐0076‐M 0.46 mm (.0180”) 3.18mm (1/8”) 0.76 mm 36.07 mm 14,49 € 131,84 €

MF208‐0051‐0076‐M 0.51 mm (.0200”) 3.18mm (1/8”) 0.76 mm 36.07 mm 14,49 € 131,84 €

MF208‐0064‐0102‐M 0.64 mm (.0250”) 3.18mm (1/8”) 1.02 mm 36.07 mm 14,49 € 131,84 €

MF208‐0071‐0127‐M 0.71 mm (.0280”) 3.18mm (1/8”) 1.27 mm 36.07 mm 8,46 € 77,03 €

MF208‐0080‐0127‐M 0.80 mm (.0313”) 3.18mm (1/8”) 1.27 mm 36.07 mm 7,87 € 71,58 €

MF208‐0100‐0191‐M 1.00 mm (.0394”) 3.18mm (1/8”) 1.91 mm 36.07 mm 7,87 € 71,58 €

MF208‐0127‐0203‐M 1.27 mm (.0500”) 3.18mm (1/8”) 2.03 mm 36.07 mm 7,87 € 71,58 €

MF208‐0159‐0330‐M 1.59 mm (.0625”) 3.18mm (1/8”) 3.30 mm 36.07 mm 7,87 € 71,58 €

MF208‐0200‐0508‐M 2.00 mm (.0787”) 3.18mm (1/8”) 5.08 mm 36.07 mm 7,87 € 71,58 €

MF208‐0238‐0457‐M 2.38 mm (.0938”) 3.18mm (1/8”) 4.57 mm 36.07 mm 8,23 € 74,87 €

MF208‐0300‐0559‐M 3.00 mm (.1181”) 3.18mm (1/8”) 5.59 mm 36.07 mm 8,23 € 74,87 €

MF208‐0318‐0508‐M 3.18 mm (.1250”) 3.18mm (1/8”) 5.08 mm 36.07 mm 8,23 € 74,87 €



Pro Metal, 2-flute stub, ball nose, end-mill – shank 3,18 mm (1/8”)


ills

Geometry – 2 flute stub, ball nose



depends on material - min. 150 rm (ebony) Material – solid submicrograin carbide Operating CNC – 20k÷100k RPM Country of Origin – USA

Ball nose tip provides step-free contour milling of 3D solid models

High flute volume supports high feed rates / chip loads Spiral geometry insures efficient debris removal


Flute geometry optimized for non-ferrous metals and soft steels, for cutting sign foam, sign board, hardwoods, thermoplastics, phenolic composites

Applications: Steel-rule die counter-plates

3D countouring and profiling 3D modeling and pattern making 3D millwork

Custom jewelry Engraving trophies, awards and medallions


MF208‐0013‐0020‐K 0.13 mm (.0050”) 3.18mm (1/8”) 0.20 mm 38.10 mm 44,89 € 408,48 €

MF208‐0015‐0023‐K 0.15 mm (.0060”) 3.18mm (1/8”) 0.23 mm 38.10 mm 44,89 € 408,48 €

MF208‐0018‐0028‐K 0.18 mm (.0070”) 3.18mm (1/8”) 0.28 mm 38.10 mm 44,89 € 408,48 €

MF208‐0020‐0030‐K 0.20 mm (.0080”) 3.18mm (1/8”) 0.30 mm 38.10 mm 44,89 € 408,48 €

MF208‐0023‐0036‐K 0.23 mm (.0090”) 3.18mm (1/8”) 0.36 mm 38.10 mm 44,89 € 408,48 €

MF208‐0025‐0038‐K 0.25 mm (.0100”) 3.18mm (1/8”) 0.38 mm 38.10 mm 38,24 € 347,96 €

MF208‐0028‐0043‐K 0.28 mm (.0110”) 3.18mm (1/8”) 0.43 mm 38.10 mm 38,24 € 347,96 €

MF208‐0030‐0045‐K 0.30 mm (.0120”) 3.18mm (1/8”) 0.45 mm 38.10 mm 38,19 € 347,53 €

MF208‐0033‐0050‐K 0.33 mm (.0130”) 3.18mm (1/8”) 0.50 mm 38.10 mm 38,19 € 347,53 €

MF208‐0036‐0053‐K 0.36 mm (.0140”) 3.18mm (1/8”) 0.53 mm 38.10 mm 38,19 € 347,53 €

MF208‐0038‐0058‐K 0.38 mm (.0150”) 3.18mm (1/8”) 0.58 mm 38.10 mm 38,19 € 347,53 €

MF208‐0041‐0061‐K 0.41 mm (.0160”) 3.18mm (1/8”) 0.61 mm 38.10 mm 34,16 € 310,87 €

MF208‐0043‐0066‐K 0.43 mm (.0170”) 3.18mm (1/8”) 0.66 mm 38.10 mm 34,16 € 310,87 €

MF208‐0046‐0069‐K 0.46 mm (.0180”) 3.18mm (1/8”) 0.69 mm 38.10 mm 34,16 € 310,87 €

MF208‐0048‐0074‐K 0.48 mm (.0190”) 3.18mm (1/8”) 0.74 mm 38.10 mm 34,16 € 310,87 €

MF208‐0051‐0076‐K 0.51 mm (.0200”) 3.18mm (1/8”) 0.76 mm 38.10 mm 34,16 € 310,87 €

MF208‐0053‐0081‐K 0.53 mm (.0210”) 3.18mm (1/8”) 0.81 mm 38.10 mm 30,13 € 274,22 €

MF208‐0056‐0084‐K 0.56 mm (.0220”) 3.18mm (1/8”) 0.84 mm 38.10 mm 30,13 € 274,22 €

MF208‐0058‐0089‐K 0.58 mm (.0230”) 3.18mm (1/8”) 0.89 mm 38.10 mm 30,13 € 274,22 €

MF208‐0061‐0091‐K 0.61 mm (.0240”) 3.18mm (1/8”) 0.91 mm 38.10 mm 30,13 € 274,22 €

MF208‐0064‐0096‐K 0.64 mm (.0250”) 3.18mm (1/8”) 0.96 mm 38.10 mm 30,13 € 274,22 €

MF208‐0066‐0099‐K 0.66 mm (.0260”) 3.18mm (1/8”) 0.99 mm 38.10 mm 30,13 € 274,22 €

MF208‐0069‐0104‐K 0.69 mm (.0270”) 3.18mm (1/8”) 1.04 mm 38.10 mm 30,13 € 274,22 €

MF208‐0071‐0107‐K 0.71 mm (.0280”) 3.18mm (1/8”) 1.07 mm 38.10 mm 30,13 € 274,22 €

MF208‐0074‐0112‐K 0.74 mm (.0290”) 3.18mm (1/8”) 1.12 mm 38.10 mm 30,13 € 274,22 €

MF208‐0076‐0114‐K 0.76 mm (.0200”) 3.18mm (1/8”) 1.14 mm 38.10 mm 30,13 € 274,22 €

MF208‐0079‐0119‐K 0.79 mm (.0312”) 3.18mm (1/8”) 1.19 mm 38.10 mm 25,53 € 232,29 €

MF208‐0089‐0135‐K 0.89 mm (.0350”) 3.18mm (1/8”) 1.35 mm 38.10 mm 25,53 € 232,29 €

MF208‐0102‐0152‐K 1.02 mm (.0400”) 3.18mm (1/8”) 1.52 mm 38.10 mm 25,53 € 232,29 €

MF208‐0114‐0178‐K 1.14 mm (.0450”) 3.18mm (1/8”) 1.78 mm 38.10 mm 25,53 € 232,29 €

MF208‐0119‐0178‐K 1.19 mm (.0469”) 3.18mm (1/8”) 1.78 mm 38.10 mm 25,53 € 232,29 €

MF208‐0127‐0191‐K 1.27 mm (.0500”) 3.18mm (1/8”) 1.91 mm 38.10 mm 25,53 € 232,29 €

MF208‐0152‐0229‐K 1.52 mm (.0600”) 3.18mm (1/8”) 2.29 mm 38.10 mm 25,53 € 232,29 €

MF208‐0180‐0254‐K 1.80 mm (.0709”) 3.18mm (1/8”) 2.54 mm 38.10 mm 25,53 € 232,29 €



ProMetric, 2-flute, fish tail, end-mill - shank 3,18 mm (1/8")

End‐M

ills

Specifications: Benefits: Geometry - 2 flute, fish tail

Overall Length - OAL - 38.10 mm ±0.25 mm Flute dia - d - nominal +0.01 -0.02 mm Shank dia - D - 3.175 mm +0.00 -0.005 mm

Helix angle - 30° Runout - TIR - max. 0.005 mm Depth Of Cut - DOC - nominal ±0.10 mm

Material - solid submicrograin carbide Operating CNC - 20k÷100k RPM Country of Origin - Germany



rates






Applications: PCB: FR2, FR3, CEM3, PTFE, Aramide, Prepregs, non-

ferrous metal Cutting inlay pockets and shaping components Shaping / routing hardwoods and softwoods

Machining reconstituted minerals Machining and slotting composites General purpose soft media machining

Item# Flute Dia. ‐ d Shank Dia. ‐ D D‐h of Cut Length ‐ OAL Price*

FR208‐0030‐0200‐M 0.30 mm (.0118”) 3.18mm (1/8”) 2.00 mm 38.10 mm 5,43 €

FR208‐0040‐0250‐M 0.40 mm (.0156”) 3.18mm (1/8”) 2.50 mm 38.10 mm 4,79 €

FR208‐0050‐0300‐M 0.50 mm (.0196”) 3.18mm (1/8”) 3.00 mm 38.10 mm 4,47 €

FR208‐0060‐0300‐M 0.60 mm (.0236”) 3.18mm (1/8”) 3.00 mm 38.10 mm 4,47 €

FR208‐0070‐0500‐M 0.70 mm (.0275”) 3.18mm (1/8”) 4.00 mm 38.10 mm 4,47 €

FR208‐0080‐0500‐M 0.80 mm (.0313”) 3.18mm (1/8”) 5.00 mm 38.10 mm 4,47 €

FR208‐0090‐0500‐M 0.90 mm (.0354”) 3.18mm (1/8”) 5.00 mm 38.10 mm 4,47 €

FR208‐0100‐0500‐M 1.00 mm (.0394”) 3.18mm (1/8”) 5.00 mm 38.10 mm 4,47 €

FR208‐0110‐0500‐M 1.10 mm (.0433”) 3.18mm (1/8”) 5.00 mm 38.10 mm 4,47 €

FR208‐0120‐0700‐M 1.20 mm (.0472”) 3.18mm (1/8”) 7.00 mm 38.10 mm 4,47 €

FR208‐0130‐0700‐M 1.30 mm (.0512”) 3.18mm (1/8”) 7.00 mm 38.10 mm 4,47 €

FR208‐0140‐0700‐M 1.40 mm (.0551”) 3.18mm (1/8”) 7.00 mm 38.10 mm 4,47 €

FR208‐0150‐0800‐M 1.50 mm (.0591”) 3.18mm (1/8”) 8.00 mm 38.10 mm 4,47 €

FR208‐0160‐0800‐M 1.60 mm (.0630”) 3.18mm (1/8”) 8.00 mm 38.10 mm 4,47 €

FR208‐0170‐0800‐M 1.70 mm (.0669”) 3.18mm (1/8”) 8.00 mm 38.10 mm 4,47 €

FR208‐0180‐0800‐M 1.80 mm (.0709”) 3.18mm (1/8”) 8.00 mm 38.10 mm 4,47 €

FR208‐0190‐0800‐M 1.90 mm (.0748”) 3.18mm (1/8”) 8.00 mm 38.10 mm 4,47 €

FR208‐0200‐0900‐M 2.00 mm (.0787”) 3.18mm (1/8”) 9.00 mm 38.10 mm 4,47 €

FR208‐0210‐0900‐M 2.10 mm (.0826”) 3.18mm (1/8”) 9.00 mm 38.10 mm 4,47 €

FR208‐0220‐0900‐M 2.20 mm (.0866”) 3.18mm (1/8”) 9.00 mm 38.10 mm 4,47 €

FR208‐0230‐0900‐M 2.30 mm (.0905”) 3.18mm (1/8”) 9.00 mm 38.10 mm 4,47 €

FR208‐0240‐0900‐M 2.40 mm (.0945”) 3.18mm (1/8”) 9.00 mm 38.10 mm 4,47 €

FR208‐0300‐1000‐M 3.00 mm (.1181”) 3.18mm (1/8”) 10.00 mm 38.10 mm 4,47 €

FR208‐0318‐1000‐M 3.18 mm (.1250”) 3.18mm (1/8”) 10.00 mm 38.10 mm 4,47 €



ProMetric, 2-flute, V-drill point, end-mill - shank 3,18 mm (1/8")


ills

Geometry - 2 flute, V-drill point






Spiral geometry insures efficient debris removal

Flute geometry enhances rigidity for more accurate, single pass cutting at high chip loads

Compatible with aluminium

Applications: Excellent suitable for aluminium Cutting inlay pockets and shaping components Shaping / routing hardwoods and softwoods

Machining and slotting composites General purpose soft media machining


FR208‐0080‐0300‐W 0.80 mm (.0313”) 3.18mm (1/8”) 3.00 mm 38.10 mm 8,95 €

FR208‐0100‐0400‐W 1.00 mm (.0394”) 3.18mm (1/8”) 4.00 mm 38.10 mm 8,95 €

FR208‐0120‐0400‐W 1.20 mm (.0472”) 3.18mm (1/8”) 4.00 mm 38.10 mm 8,95 €

FR208‐0140‐0400‐W 1.40 mm (.0551”) 3.18mm (1/8”) 4.00 mm 38.10 mm 8,95 €

FR208‐0150‐0500‐W 1.50 mm (.0591”) 3.18mm (1/8”) 5.00 mm 38.10 mm 8,95 €

FR208‐0160‐0500‐W 1.60 mm (.0630”) 3.18mm (1/8”) 5.00 mm 38.10 mm 8,95 €

FR208‐0180‐0600‐W 1.80 mm (.0709”) 3.18mm (1/8”) 6.00 mm 38.10 mm 8,95 €

FR208‐0200‐0700‐W 2.00 mm (.0787”) 3.18mm (1/8”) 7.00 mm 38.10 mm 8,95 €

FR208‐0240‐0700‐W 2.40 mm (.0945”) 3.18mm (1/8”) 7.00 mm 38.10 mm 8,95 €

FR208‐0300‐0800‐W 3.00 mm (.1181”) 3.18mm (1/8”) 8.00 mm 38.10 mm 8,95 €



ProMetric, 1-flute, V-drill point, end-mill - shank 3,18 mm (1/8")

End‐M

ills

Specifications: Benefits: Geometry - 1 flute, V-drill point






Spiral geometry insures efficient debris removal


Compatible with aluminium

Applications: Excellent suitable for aluminium, flexible materials and plastics Cutting inlay pockets and shaping components Shaping / routing hardwoods and softwoods

Machining and slotting composites General purpose soft media machining


FR108‐0080‐0300‐W 0.80 mm (.0313”) 3.18mm (1/8”) 3.00 mm 38.10 mm 9,43 €

FR108‐0100‐0400‐W 1.00 mm (.0394”) 3.18mm (1/8”) 4.00 mm 38.10 mm 9,43 €

FR108‐0120‐0400‐W 1.20 mm (.0472”) 3.18mm (1/8”) 4.00 mm 38.10 mm 9,43 €

FR108‐0160‐0500‐W 1.60 mm (.0630”) 3.18mm (1/8”) 5.00 mm 38.10 mm 9,43 €

FR108‐0200‐0800‐W 2.00 mm (.0787”) 3.18mm (1/8”) 8.00 mm 38.10 mm 9,43 €

FR108‐0240‐0800‐W 2.40 mm (.0945”) 3.18mm (1/8”) 8.00 mm 38.10 mm 9,43 €

FR108‐0300‐0900‐W 3.00 mm (.1181”) 3.18mm (1/8”) 9.00 mm 38.10 mm 9,43 €



Pro, 2-flute left, fish tail, end-mill – shank 3,18 mm (1/8”)


ills/Down‐Cut

Geometry - 2-flute down-cut, shallow fish tail point

Overall Length - OAL - 38.10 mm ±0.25 mm Flute dia - d - nominal +0.01 -0.02 mm Shank dia - D - 3.175 mm +0.00 -0.005 mm Helix angle - 28°

Runout - TIR - max. 0.005 mm Depth Of Cut - DOC - nominal ±0.10 mm Anticipated Life:

depends on material - min. 150 rm (ebony) Material - solid submicrograin carbide Operating CNC - 20k÷100k RPM

Country of Origin - USA

Down-cut geometry eliminates top surface splintering and fraying

High flute volume supports high feed rates / chip loads Cutting edge geometry virtually eliminates chatter at

high feed rates


Compatible with basswood, balsa, pine, birch plywood, styrofoam

Applications: Cleaning up edges of inlay pockets and components

Shaping / routing materials for model airplanes



FD208‐0080‐0318‐M 0.80 mm (.0313”) 3.18mm (1/8”) 3.18 mm 38.10 mm 8,78 € 79,88 €

FD208‐0100‐0635‐M 1.00 mm (.0394”) 3.18mm (1/8”) 6.35 mm 38.10 mm 8,88 € 80,83 €

FD208‐0159‐0610‐M 1.59 mm (.0625”) 3.18mm (1/8”) 6.10 mm 38.10 mm 9,81 € 89,30 €

FD208‐0300‐1270‐M 3.00 mm (.1181”) 3.18mm (1/8”) 12.70 mm 38.10 mm 9,81 € 89,30 €

FD208‐0318‐1270‐M 3.18 mm (.1250”) 3.18mm (1/8”) 12.70 mm 38.10 mm 9,81 € 89,30 €



ProMetric, 2-flute left, fish tail, end-mill - shank 3,18 mm (1/8")

End‐M

ills /D

own‐Cut

Specifications: Benefits: Geometry - 2 flute left, fish tail






rates






Applications: PCB: FR2, FR3, CEM3, PTFE, Aramide, Prepregs, non-

ferrous metal Cutting inlay pockets and shaping components Shaping / routing hardwoods and softwoods



FL208‐0060‐0300‐M 0.60 mm (.0236”) 3.18mm (1/8”) 3.00 mm 38.10 mm 7,67 €

FL208‐0080‐0400‐M 0.80 mm (.0313”) 3.18mm (1/8”) 4.00 mm 38.10 mm 7,67 €

FL208‐0100‐0500‐M 1.00 mm (.0394”) 3.18mm (1/8”) 5.00 mm 38.10 mm 7,67 €

FL208‐0120‐0500‐M 1.20 mm (.0472”) 3.18mm (1/8”) 5.00 mm 38.10 mm 7,67 €

FL208‐0140‐0700‐M 1.40 mm (.0551”) 3.18mm (1/8”) 7.00 mm 38.10 mm 7,67 €

FL208‐0150‐0700‐M 1.50 mm (.0591”) 3.18mm (1/8”) 7.00 mm 38.10 mm 7,67 €

FL208‐0160‐0700‐M 1.60 mm (.0630”) 3.18mm (1/8”) 7.00 mm 38.10 mm 7,67 €

FL208‐0180‐0700‐M 1.80 mm (.0709”) 3.18mm (1/8”) 7.00 mm 38.10 mm 7,67 €

FL208‐0200‐0700‐M 2.00 mm (.0787”) 3.18mm (1/8”) 7.00 mm 38.10 mm 7,67 €

FL208‐0240‐0900‐M 2.40 mm (.0945”) 3.18mm (1/8”) 9.00 mm 38.10 mm 7,67 €



Pro, 3-flute, fish tail, end-mill - shank 4,76 mm (3/16")

Specifications: Benefits:

End‐M

ills

Geometry - 3-flute, fish tail

Overall Length - OAL - 50.80 mm ±0.25 mm Flute dia - d - 4.76 mm +0.01 -0.02 mm Shank dia - D - 4.76 mm +0.00 -0.005 mm

Runout - TIR - max. 0.005 mm Depth Of Cut - DOC - nominal ±0.50 mm Anticipated Life:

Baltic birch plywood - min. 500 rm Material - solid submicrograin carbide Operating CNC - 1k÷40k RPM Country of Origin - USA

High speed cutting at 85-100 mm/s @ 40,000 RPM


Flute geometry minimizes topside fuzz and splintering

Up-draft chip extraction reduces debris compaction High flute volume supports high feed rates / chip loads Unique flute and tip geometries supports milling and

drilling with same tool

Applications: Dimensional signage Cabinetry, furniture making

Shaping / routing hardwoods and softwoods High speed cutting of softwoods Machining and slotting composite

Steel rule die contour cutout and registration hole drilling Counter board alignment hole drilling Steel rule die blankers and strippers


F303‐0476‐1900‐M 4.76 mm (.1875”) 4.76 mm (3/16") 19.00 mm 50.80 mm 27,44 € ‐


Pro 4-flute tapered, ball nose, Carving tool – shank 6,35 mm (1/4”)


Carvin

g Tools

Geometry – 3, 4 flute, tapered, ball nose Overall Length – OAL – 63.50 ±0.25 mm Flute dia – d – nominal +0.00 -0.02 mm

Shank dia – D – 6.35 mm +0.00 -0.002 mm Runout – TIR – max. 0.005 mm Depth Of Cut – DOC – 25.40 ±0.10 mm

Anticipated Life: Baltic birch plywood - min. 500 rm



High-shear ball-nose tip cuts smooth 3D contours with reduced stepping, and minimal fuzzing


High flute volume supports high feed rates / chip loads High aspect ratio for single pass deep-reach cutting


Optimized flute geometry and low TIR insures clean cutting, virtually eliminating sanding and fuzz removal (when used with low TIR spindles)


Precision 3D carving and large scale 3D carving 3D countouring and profiling Cabinetry, furniture making

Jewelry mold making 3D modeling and pattern making 3D millwork Compatible with CarveWright and CompuCarve

woodworking systems


CF304‐0080‐2540‐K ‐ 0.80 mm (.0313”) 6.35mm (1/4”) 25.40 mm 63.50 mm 31,30 € ‐

CF304‐0080‐2540‐KZ ZrN 0.80 mm (.0313”) 6.35mm (1/4”) 25.40 mm 63.50 mm 40,80 € ‐

CF404‐0159‐2540‐K ‐ 1.59 mm (.0625”) 6.35mm (1/4”) 25.40 mm 63.50 mm 28,45 € ‐


CF404‐0318‐2540‐K ‐ 3.18 mm (.1250”) 6.35mm (1/4”) 25.40 mm 63.50 mm 28,45 € ‐


CF404‐0635‐2540‐K ‐ 6.35 mm (.2500”) 6.35mm (1/4”) 25.40 mm 63.50 mm 28,45 € ‐




Pro, 2-flute 28°, V-drill point, drill bit – shank 3,18 mm (1/8”)

Drill Bits

Specifications: Benefits: Geometry – 2 flute, drill point






Drilling hardwoods, composites, non-ferrous metals

Inlay pockets for mother-of-pearl dots Drilling printed circuit substrates

Applications: Shallow point angle minimizes backside breakout and

splintering Tip geometry produces shallow glue pockets for anchoring

inlaid components

Point geometry and back tapered flutes virtually eliminate top surface splintering

Four facet drill point minimizes grabbing and lifting of work-piece


W208‐0020‐0381‐W 0.20 mm (.012”) 3.18mm (1/8”) 5.84 mm 38.10 mm 8,15 € 74,17 €

W208‐0030‐0584‐W 0.30 mm (.012”) 3.18mm (1/8”) 5.84 mm 38.10 mm 5,90 € 53,69 €

W208‐0040‐0584‐W 0.40 mm (.016”) 3.18mm (1/8”) 5.84 mm 38.10 mm 2,68 € 24,38 €

W208‐0050‐0787‐W 0.50 mm (.020”) 3.18mm (1/8”) 7.87 mm 38.10 mm 2,68 € 24,38 €

W208‐0060‐0864‐W 0.60 mm (.024”) 3.18mm (1/8”) 8.64 mm 38.10 mm 2,68 € 24,38 €

W208‐0070‐1016‐W 0.70 mm (.028”) 3.18mm (1/8”) 10.16 mm 38.10 mm 2,68 € 24,38 €

W208‐0080‐1016‐W 0.80 mm (.032”) 3.18mm (1/8”) 10.16 mm 38.10 mm 2,36 € 21,44 €

W208‐0090‐1016‐W 0.90 mm (.035”) 3.18mm (1/8”) 10.16 mm 38.10 mm 2,36 € 21,44 €

W208‐0100‐1016‐W 1.00 mm (.039”) 3.18mm (1/8”) 10.16 mm 38.10 mm 2,36 € 21,44 €

W208‐0110‐1016‐W 1.10 mm (.043”) 3.18mm (1/8”) 10.16 mm 38.10 mm 2,36 € 21,44 €

W208‐0120‐1016‐W 1.20 mm (.047”) 3.18mm (1/8”) 10.16 mm 38.10 mm 2,36 € 21,44 €

W208‐0130‐1016‐W 1.30 mm (.051”) 3.18mm (1/8”) 10.16 mm 38.10 mm 2,36 € 21,44 €

W208‐0140‐1016‐W 1.40 mm (.055”) 3.18mm (1/8”) 10.16 mm 38.10 mm 2,36 € 21,44 €

W208‐0150‐1016‐W 1.50 mm (.059”) 3.18mm (1/8”) 10.16 mm 38.10 mm 2,36 € 21,44 €

W208‐0160‐1016‐W 1.60 mm (.063”) 3.18mm (1/8”) 10.16 mm 38.10 mm 2,36 € 21,44 €

W208‐0170‐1016‐W 1.70 mm (.067”) 3.18mm (1/8”) 10.16 mm 38.10 mm 2,36 € 21,44 €

W208‐0180‐1016‐W 1.80 mm (.071”) 3.18mm (1/8”) 10.16 mm 38.10 mm 2,36 € 21,44 €

W208‐0190‐1016‐W 1.90 mm (.075”) 3.18mm (1/8”) 10.16 mm 38.10 mm 2,36 € 21,44 €

W208‐0200‐1016‐W 2.00 mm (.079”) 3.18mm (1/8”) 10.16 mm 38.10 mm 2,62 € 23,86 €

W208‐0210‐1016‐W 2.10 mm (.083”) 3.18mm (1/8”) 10.16 mm 38.10 mm 2,62 € 23,86 €

W208‐0220‐1016‐W 2.20 mm (.087”) 3.18mm (1/8”) 10.16 mm 38.10 mm 2,62 € 23,86 €

W208‐0230‐1016‐W 2.30 mm (.091”) 3.18mm (1/8”) 10.16 mm 38.10 mm 2,62 € 23,86 €

W208‐0240‐1016‐W 2.40 mm (.095”) 3.18mm (1/8”) 10.16 mm 38.10 mm 2,62 € 23,86 €

W208‐0250‐1016‐W 2.50 mm (.098”) 3.18mm (1/8”) 10.16 mm 38.10 mm 2,62 € 23,86 €

W208‐0260‐1016‐W 2.60 mm (.102”) 3.18mm (1/8”) 10.16 mm 38.10 mm 2,62 € 23,86 €

W208‐0270‐1016‐W 2.70 mm (.106”) 3.18mm (1/8”) 10.16 mm 38.10 mm 2,62 € 23,86 €

W208‐0280‐1016‐W 2.80 mm (.110”) 3.18mm (1/8”) 10.16 mm 38.10 mm 2,62 € 23,86 €

W208‐0290‐1016‐W 2.90 mm (.114”) 3.18mm (1/8”) 10.16 mm 38.10 mm 2,62 € 23,86 €

W208‐0300‐1016‐W 3.00 mm (.118”) 3.18mm (1/8”) 10.16 mm 38.10 mm 2,62 € 23,86 €

W208‐0310‐1270‐W 3.10 mm (.122”) 3.18mm (1/8”) 12.70 mm 38.10 mm 2,62 € 23,86 €

W208‐0320‐1270‐W 3.20 mm (.126”) 3.18mm (1/8”) 12.70 mm 38.10 mm 4,98 € 45,30 €

W208‐0330‐1270‐W 3.30 mm (.130”) 3.18mm (1/8”) 12.70 mm 38.10 mm 4,98 € 45,30 €

W208‐0340‐1270‐W 3.40 mm (.134”) 3.18mm (1/8”) 12.70 mm 38.10 mm 4,98 € 45,30 €

W208‐0350‐1270‐W 3.50 mm (.138”) 3.18mm (1/8”) 12.70 mm 38.10 mm 4,98 € 45,30 €

W208‐0360‐1270‐W 3.60 mm (.142”) 3.18mm (1/8”) 12.70 mm 38.10 mm 6,83 € 62,16 €

W208‐0370‐1270‐W 3.70 mm (.146”) 3.18mm (1/8”) 12.70 mm 38.10 mm 6,83 € 62,16 €

W208‐0380‐1270‐W 3.80 mm (.150”) 3.18mm (1/8”) 12.70 mm 38.10 mm 6,83 € 62,16 €



W208‐0390‐1270‐W 3.90 mm (.154”) 3.18mm (1/8”) 12.70 mm 38.10 mm 6,83 € 62,16 €

W208‐0400‐1270‐W 4.00 mm (.158”) 3.18mm (1/8”) 12.70 mm 38.10 mm 6,83 € 62,16 €

W208‐0410‐1270‐W 4.10 mm (.161”) 3.18mm (1/8”) 12.70 mm 38.10 mm 7,38 € 67,17 €

W208‐0420‐1270‐W 4.20 mm (.165”) 3.18mm (1/8”) 12.70 mm 38.10 mm 7,38 € 67,17 €

W208‐0430‐1270‐W 4.30 mm (.169”) 3.18mm (1/8”) 12.70 mm 38.10 mm 7,38 € 67,17 €

W208‐0440‐1270‐W 4.40 mm (.173”) 3.18mm (1/8”) 12.70 mm 38.10 mm 7,38 € 67,17 €

W208‐0450‐1270‐W 4.50 mm (.177”) 3.18mm (1/8”) 12.70 mm 38.10 mm 7,52 € 68,47 €

W208‐0460‐1270‐W 4.60 mm (.181”) 3.18mm (1/8”) 12.70 mm 38.10 mm 7,52 € 68,47 €

W208‐0470‐1270‐W 4.70 mm (.185”) 3.18mm (1/8”) 12.70 mm 38.10 mm 7,52 € 68,47 €

W208‐0480‐1270‐W 4.80 mm (.189”) 3.18mm (1/8”) 12.70 mm 38.10 mm 7,52 € 68,47 €

W208‐0490‐1270‐W 4.90 mm (.193”) 3.18mm (1/8”) 12.70 mm 38.10 mm 8,78 € 79,88 €

W208‐0500‐1270‐W 5.00 mm (.197”) 3.18mm (1/8”) 12.70 mm 38.10 mm 8,78 € 79,88 €

W208‐0510‐1270‐W 5.10 mm (.201”) 3.18mm (1/8”) 12.70 mm 38.10 mm 8,78 € 79,88 €

W208‐0520‐1270‐W 5.20 mm (.205”) 3.18mm (1/8”) 12.70 mm 38.10 mm 8,78 € 79,88 €

W208‐0530‐1270‐W 5.30 mm (.209”) 3.18mm (1/8”) 12.70 mm 38.10 mm 9,41 € 85,67 €

W208‐0540‐1270‐W 5.40 mm (.213”) 3.18mm (1/8”) 12.70 mm 38.10 mm 9,41 € 85,67 €

W208‐0550‐1270‐W 5.50 mm (.217”) 3.18mm (1/8”) 12.70 mm 38.10 mm 9,41 € 85,67 €

W208‐0560‐1270‐W 5.60 mm (.220”) 3.18mm (1/8”) 12.70 mm 38.10 mm 10,41 € 94,75 €

W208‐0570‐1270‐W 5.70 mm (.224”) 3.18mm (1/8”) 12.70 mm 38.10 mm 10,41 € 94,75 €

W208‐0580‐1270‐W 5.80 mm (.228”) 3.18mm (1/8”) 12.70 mm 38.10 mm 10,41 € 94,75 €

W208‐0590‐1270‐W 5.90 mm (.232”) 3.18mm (1/8”) 12.70 mm 38.10 mm 10,41 € 94,75 €

W208‐0600‐1270‐W 6.00 mm (.236”) 3.18mm (1/8”) 12.70 mm 38.10 mm 10,41 € 94,75 €

W208‐0610‐1270‐W 6.10 mm (.240”) 3.18mm (1/8”) 12.70 mm 38.10 mm 10,41 € 94,75 €

W208‐0620‐1270‐W 6.20 mm (.244”) 3.18mm (1/8”) 12.70 mm 38.10 mm 11,31 € 102,96 €

W208‐0630‐1270‐W 6.30mm (.248”) 3.18mm (1/8”) 12.70 mm 38.10 mm 11,31 € 102,96 €



ProMetric, 2-flute 35/30° UC, V-drill point, drill bit - steel shank 3,18 mm (1/8")

Drill Bits

Specifications: Benefits: Geometry - 2 flute Undercut, drill point

0.15÷0.80 mm - medium 35° 0.85÷1.00 mm - elastic 30°

Overall Length - OAL - 38.10 mm ±0.25 mm

Flute dia - d - nominal +0.00 -0.005 mm Shank dia - D - 3.175 mm +0.00 -0.005 mm Helix angle - 35°/30°

Point angle - 130° Runout - TIR - max. 0.005 mm Depth Of Cut - DOC - nominal ±0.20 mm

Material - solid carbide/steel shank Operating CNC - 20k÷180k RPM Country of Origin - Germany

Special flute (Undercut/Spade Type) for multilayer PCBs with filled materials and for high TG and BT resins, stands out for good chip removal

Shallow point angle minimizes backside breakout and splintering


Applications: PCB: Multilayer ≥ 8 layers, Polyimid, High Tg, BT resins,

FR2, FR3, FR4, PTFE, Aramid Drilling hardwoods, composites, non-ferrous metals

Drilling printed circuit substrates


W35U208‐0015‐0250‐W 0.15 mm (.005”) 3.18mm (1/8”) 2.50 mm 38.10 mm 2,96 €

W35U208‐0017‐0300‐W 0.175 mm (.006”) 3.18mm (1/8”) 3.00 mm 38.10 mm 2,96 €

W35U208‐0020‐0350‐W 0.20 mm (.007”) 3.18mm (1/8”) 3.50 mm 38.10 mm 2,96 €

W35U208‐0020‐0500‐W 0.20 mm (.007”) 3.18mm (1/8”) 5.00 mm 38.10 mm 2,96 €

W35U208‐0022‐0350‐W 0.225 mm (.008”) 3.18mm (1/8”) 3.50 mm 38.10 mm 2,96 €

W35U208‐0025‐0350‐W 0.25 mm (.009”) 3.18mm (1/8”) 3.50 mm 38.10 mm 2,96 €

W35U208‐0025‐0500‐W 0.25 mm (.009”) 3.18mm (1/8”) 5.00 mm 38.10 mm 2,96 €

W35U208‐0027‐0500‐W 0.275 mm (.011”) 3.18mm (1/8”) 5.00 mm 38.10 mm 2,96 €

W35U208‐0030‐0550‐W 0.30 mm (.012”) 3.18mm (1/8”) 5.50 mm 38.10 mm 2,96 €

W35U208‐0030‐0700‐W 0.30 mm (.012”) 3.18mm (1/8”) 7.00 mm 38.10 mm 2,96 €

W35U208‐0035‐0550‐W 0.35 mm (.014”) 3.18mm (1/8”) 5.50 mm 38.10 mm 2,96 €

W35U208‐0035‐0700‐W 0.35 mm (.014”) 3.18mm (1/8”) 7.00 mm 38.10 mm 2,96 €

W35U208‐0040‐0550‐W 0.40 mm (.016”) 3.18mm (1/8”) 5.50 mm 38.10 mm 2,92 €

W35U208‐0040‐0700‐W 0.40 mm (.016”) 3.18mm (1/8”) 7.00 mm 38.10 mm 2,92 €

W35U208‐0045‐0550‐W 0.45 mm (.018”) 3.18mm (1/8”) 5.50 mm 38.10 mm 2,80 €

W35U208‐0045‐0700‐W 0.45 mm (.018”) 3.18mm (1/8”) 7.00 mm 38.10 mm 2,80 €

W35U208‐0050‐0550‐W 0.50 mm (.020”) 3.18mm (1/8”) 5.50 mm 38.10 mm 2,80 €

W35U208‐0050‐0700‐W 0.50 mm (.020”) 3.18mm (1/8”) 7.00 mm 38.10 mm 2,80 €

W35U208‐0055‐0700‐W 0.55 mm (.022”) 3.18mm (1/8”) 7.00 mm 38.10 mm 2,80 €

W35U208‐0060‐0850‐W 0.60 mm (.024”) 3.18mm (1/8”) 8.50 mm 38.10 mm 2,80 €

W35U208‐0065‐0850‐W 0.65 mm (.026”) 3.18mm (1/8”) 8.50 mm 38.10 mm 2,80 €

W35U208‐0070‐0850‐W 0.70 mm (.028”) 3.18mm (1/8”) 8.50 mm 38.10 mm 2,80 €

W35U208‐0075‐0850‐W 0.75 mm (.030”) 3.18mm (1/8”) 8.50 mm 38.10 mm 2,80 €

W35U208‐0080‐1050‐W 0.80 mm (.032”) 3.18mm (1/8”) 10.50 mm 38.10 mm 2,80 €

W30U208‐0085‐1050‐W 0.85 mm (.034”) 3.18mm (1/8”) 10.50 mm 38.10 mm 2,80 €

W30U208‐0090‐1050‐W 0.90 mm (.035”) 3.18mm (1/8”) 10.50 mm 38.10 mm 2,80 €

W30U208‐0095‐1050‐W 0.95 mm (.037”) 3.18mm (1/8”) 10.50 mm 38.10 mm 2,80 €

W30U208‐0100‐1050‐W 1.00 mm (.039”) 3.18mm (1/8”) 10.50 mm 38.10 mm 2,80 €

W30U208‐0105‐1050‐W 1.05 mm (.041”) 3.18mm (1/8”) 10.50 mm 38.10 mm 2,80 €

W30U208‐0110‐1050‐W 1.10 mm (.043”) 3.18mm (1/8”) 10.50 mm 38.10 mm 2,80 €

W30U208‐0115‐1050‐W 1.15 mm (.045”) 3.18mm (1/8”) 10.50 mm 38.10 mm 2,80 €

W30U208‐0120‐1050‐W 1.20 mm (.047”) 3.18mm (1/8”) 10.50 mm 38.10 mm 2,80 €

W30U208‐0125‐1050‐W 1.25 mm (.049”) 3.18mm (1/8”) 10.50 mm 38.10 mm 2,80 €

W30U208‐0130‐1050‐W 1.30 mm (.051”) 3.18mm (1/8”) 10.50 mm 38.10 mm 2,80 €

W30U208‐0135‐1050‐W 1.35 mm (.053”) 3.18mm (1/8”) 10.50 mm 38.10 mm 2,80 €

W30U208‐0140‐1050‐W 1.40 mm (.055”) 3.18mm (1/8”) 10.50 mm 38.10 mm 2,80 €



W30U208‐0145‐1050‐W 1.45 mm (.057”) 3.18mm (1/8”) 10.50 mm 38.10 mm 2,80 €

W30U208‐0150‐1050‐W 1.50 mm (.059”) 3.18mm (1/8”) 10.50 mm 38.10 mm 2,80 €

W30U208‐0155‐1050‐W 1.55 mm (.061”) 3.18mm (1/8”) 10.50 mm 38.10 mm 2,80 €

W30U208‐0160‐1050‐W 1.60 mm (.063”) 3.18mm (1/8”) 10.50 mm 38.10 mm 2,80 €

W30U208‐0165‐1050‐W 1.65 mm (.065”) 3.18mm (1/8”) 10.50 mm 38.10 mm 2,80 €

W30U208‐0170‐1050‐W 1.70 mm (.067”) 3.18mm (1/8”) 10.50 mm 38.10 mm 2,80 €

W30U208‐0175‐1050‐W 1.75 mm (.069”) 3.18mm (1/8”) 10.50 mm 38.10 mm 2,80 €

W30U208‐0180‐1050‐W 1.80 mm (.071”) 3.18mm (1/8”) 10.50 mm 38.10 mm 2,80 €

W30U208‐0185‐1050‐W 1.85 mm (.073”) 3.18mm (1/8”) 10.50 mm 38.10 mm 2,80 €

W30U208‐0190‐1050‐W 1.90 mm (.075”) 3.18mm (1/8”) 10.50 mm 38.10 mm 2,80 €

W30U208‐0195‐1050‐W 1.95 mm (.077”) 3.18mm (1/8”) 10.50 mm 38.10 mm 2,80 €

W30U208‐0200‐1050‐W 2.00 mm (.079”) 3.18mm (1/8”) 10.50 mm 38.10 mm 2,80 €


ProMetric, 2-flute 30°, V-drill point, drill bit - shank 3,18 mm (1/8")

Specifications: Benefits: Drill B

its

Geometry - 2 flute Straight, drill point 0.30÷6.50 mm - elastic 30°


Helix angle - 30° Point angle - <3.175 - 130°, >3.175 - 165° Runout - TIR - max. 0.005 mm

Depth Of Cut - DOC - nominal ±0.20 mm Material - solid carbide/ < 3.05 steel shank Operating CNC - 20k÷180k RPM Country of Origin - Germany

To be used for standard multilayer PCBs, stands out for good chip removal




FR2, FR3, FR4, PTFE, Aramid, CEM3

Drilling hardwoods, composites, non-ferrous metals Drilling printed circuit substrates


W30S208‐0030‐0550‐W 0.30 mm (.012”) 3.18mm (1/8”) 5.50 mm 38.10 mm 1,66 €

W30S208‐0030‐0700‐W 0.30 mm (.012”) 3.18mm (1/8”) 7.00 mm 38.10 mm 1,66 €

W30S208‐0035‐0550‐W 0.35 mm (.014”) 3.18mm (1/8”) 5.50 mm 38.10 mm 1,66 €

W30S208‐0035‐0700‐W 0.35 mm (.014”) 3.18mm (1/8”) 7.00 mm 38.10 mm 1,66 €

W30S208‐0040‐0550‐W 0.40 mm (.016”) 3.18mm (1/8”) 5.50 mm 38.10 mm 1,56 €

W30S208‐0040‐0700‐W 0.40 mm (.016”) 3.18mm (1/8”) 7.00 mm 38.10 mm 1,56 €

W30S208‐0045‐0550‐W 0.45 mm (.018”) 3.18mm (1/8”) 5.50 mm 38.10 mm 1,56 €

W30S208‐0045‐0700‐W 0.45 mm (.018”) 3.18mm (1/8”) 7.00 mm 38.10 mm 1,56 €

W30S208‐0050‐0550‐W 0.50 mm (.020”) 3.18mm (1/8”) 5.50 mm 38.10 mm 1,56 €

W30S208‐0050‐0700‐W 0.50 mm (.020”) 3.18mm (1/8”) 7.00 mm 38.10 mm 1,56 €

W30S208‐0055‐0700‐W 0.55 mm (.022”) 3.18mm (1/8”) 7.00 mm 38.10 mm 1,56 €

W30S208‐0055‐0850‐W 0.55 mm (.022”) 3.18mm (1/8”) 8.50 mm 38.10 mm 1,56 €

W30S208‐0060‐0700‐W 0.60 mm (.024”) 3.18mm (1/8”) 7.00 mm 38.10 mm 1,56 €

W30S208‐0060‐0850‐W 0.60 mm (.024”) 3.18mm (1/8”) 8.50 mm 38.10 mm 1,56 €

W30S208‐0065‐0700‐W 0.65 mm (.026”) 3.18mm (1/8”) 7.00 mm 38.10 mm 1,56 €

W30S208‐0065‐0850‐W 0.65 mm (.026”) 3.18mm (1/8”) 8.50 mm 38.10 mm 1,56 €

W30S208‐0070‐0850‐W 0.70 mm (.028”) 3.18mm (1/8”) 8.50 mm 38.10 mm 1,56 €

W30S208‐0070‐1050‐W 0.70 mm (.028”) 3.18mm (1/8”) 10.50 mm 38.10 mm 1,56 €

W30S208‐0075‐0850‐W 0.75 mm (.030”) 3.18mm (1/8”) 8.50 mm 38.10 mm 1,56 €

W30S208‐0075‐1050‐W 0.75 mm (.030”) 3.18mm (1/8”) 10.50 mm 38.10 mm 1,56 €

W30S208‐0080‐1050‐W 0.80 mm (.032”) 3.18mm (1/8”) 10.50 mm 38.10 mm 1,56 €

W30S208‐0085‐1050‐W 0.85 mm (.034”) 3.18mm (1/8”) 10.50 mm 38.10 mm 1,56 €



W30S208‐0090‐1050‐W 0.90 mm (.035”) 3.18mm (1/8”) 10.50 mm 38.10 mm 1,56 €

W30S208‐0095‐1050‐W 0.95 mm (.037”) 3.18mm (1/8”) 10.50 mm 38.10 mm 1,56 €

W30S208‐0100‐1050‐W 1.00 mm (.039”) 3.18mm (1/8”) 10.50 mm 38.10 mm 1,56 €

W30S208‐0105‐1050‐W 1.05 mm (.041”) 3.18mm (1/8”) 10.50 mm 38.10 mm 1,56 €

W30S208‐0110‐1050‐W 1.10 mm (.043”) 3.18mm (1/8”) 10.50 mm 38.10 mm 1,56 €

W30S208‐0115‐1050‐W 1.15 mm (.045”) 3.18mm (1/8”) 10.50 mm 38.10 mm 1,56 €

W30S208‐0120‐1050‐W 1.20 mm (.047”) 3.18mm (1/8”) 10.50 mm 38.10 mm 1,56 €

W30S208‐0125‐1050‐W 1.25 mm (.049”) 3.18mm (1/8”) 10.50 mm 38.10 mm 1,56 €

W30S208‐0130‐1050‐W 1.30 mm (.051”) 3.18mm (1/8”) 10.50 mm 38.10 mm 1,56 €

W30S208‐0135‐1050‐W 1.35 mm (.053”) 3.18mm (1/8”) 10.50 mm 38.10 mm 1,56 €

W30S208‐0140‐1050‐W 1.40 mm (.055”) 3.18mm (1/8”) 10.50 mm 38.10 mm 1,56 €

W30S208‐0145‐1050‐W 1.45 mm (.057”) 3.18mm (1/8”) 10.50 mm 38.10 mm 1,56 €

W30S208‐0150‐1050‐W 1.50 mm (.059”) 3.18mm (1/8”) 10.50 mm 38.10 mm 1,56 €

W30S208‐0155‐1050‐W 1.55 mm (.061”) 3.18mm (1/8”) 10.50 mm 38.10 mm 1,56 €

W30S208‐0160‐1050‐W 1.60 mm (.063”) 3.18mm (1/8”) 10.50 mm 38.10 mm 1,56 €

W30S208‐0165‐1050‐W 1.65 mm (.065”) 3.18mm (1/8”) 10.50 mm 38.10 mm 1,56 €

W30S208‐0170‐1050‐W 1.70 mm (.067”) 3.18mm (1/8”) 10.50 mm 38.10 mm 1,56 €

W30S208‐0175‐1050‐W 1.75 mm (.069”) 3.18mm (1/8”) 10.50 mm 38.10 mm 1,56 €

W30S208‐0180‐1050‐W 1.80 mm (.071”) 3.18mm (1/8”) 10.50 mm 38.10 mm 1,56 €

W30S208‐0185‐1050‐W 1.85 mm (.073”) 3.18mm (1/8”) 10.50 mm 38.10 mm 1,56 €

W30S208‐0190‐1050‐W 1.90 mm (.075”) 3.18mm (1/8”) 10.50 mm 38.10 mm 1,56 €

W30S208‐0195‐1050‐W 1.95 mm (.077”) 3.18mm (1/8”) 10.50 mm 38.10 mm 1,56 €

W30S208‐0200‐1050‐W 2.00 mm (.079”) 3.18mm (1/8”) 10.50 mm 38.10 mm 1,56 €

W30S208‐0205‐1050‐W 2.05 mm (.081”) 3.18mm (1/8”) 10.50 mm 38.10 mm 1,56 €

W30S208‐0210‐1050‐W 2.10 mm (.083”) 3.18mm (1/8”) 10.50 mm 38.10 mm 1,56 €

W30S208‐0215‐1050‐W 2.15 mm (.085”) 3.18mm (1/8”) 10.50 mm 38.10 mm 1,56 €

W30S208‐0220‐1050‐W 2.20 mm (.087”) 3.18mm (1/8”) 10.50 mm 38.10 mm 1,56 €

W30S208‐0225‐1050‐W 2.25 mm (.089”) 3.18mm (1/8”) 10.50 mm 38.10 mm 1,56 €

W30S208‐0230‐1050‐W 2.30 mm (.091”) 3.18mm (1/8”) 10.50 mm 38.10 mm 1,56 €

W30S208‐0235‐1050‐W 2.35 mm (.093”) 3.18mm (1/8”) 10.50 mm 38.10 mm 1,56 €

W30S208‐0240‐1050‐W 2.40 mm (.095”) 3.18mm (1/8”) 10.50 mm 38.10 mm 1,56 €

W30S208‐0245‐1050‐W 2.45 mm (.096”) 3.18mm (1/8”) 10.50 mm 38.10 mm 1,56 €

W30S208‐0250‐1050‐W 2.50 mm (.098”) 3.18mm (1/8”) 10.50 mm 38.10 mm 1,56 €

W30S208‐0255‐1050‐W 2.55 mm (.100”) 3.18mm (1/8”) 10.50 mm 38.10 mm 1,56 €

W30S208‐0260‐1050‐W 2.60 mm (.102”) 3.18mm (1/8”) 10.50 mm 38.10 mm 1,56 €

W30S208‐0265‐1050‐W 2.65 mm (.104”) 3.18mm (1/8”) 10.50 mm 38.10 mm 1,56 €

W30S208‐0270‐1050‐W 2.70 mm (.106”) 3.18mm (1/8”) 10.50 mm 38.10 mm 1,56 €

W30S208‐0275‐1050‐W 2.75 mm (.108”) 3.18mm (1/8”) 10.50 mm 38.10 mm 1,56 €

W30S208‐0280‐1050‐W 2.80 mm (.110”) 3.18mm (1/8”) 10.50 mm 38.10 mm 1,56 €

W30S208‐0285‐1050‐W 2.85 mm (.112”) 3.18mm (1/8”) 10.50 mm 38.10 mm 1,56 €

W30S208‐0290‐1050‐W 2.90 mm (.114”) 3.18mm (1/8”) 10.50 mm 38.10 mm 1,56 €

W30S208‐0295‐1050‐W 2.95 mm (.116”) 3.18mm (1/8”) 10.50 mm 38.10 mm 1,56 €

W30S208‐0300‐1050‐W 3.00 mm (.118”) 3.18mm (1/8”) 10.50 mm 38.10 mm 1,56 €

W30S208‐0305‐1050‐W 3.05 mm (.120”) 3.18mm (1/8”) 10.50 mm 38.10 mm 1,66 €

W30S208‐0310‐1050‐W 3.10 mm (.122”) 3.18mm (1/8”) 10.50 mm 38.10 mm 1,66 €

W30S208‐0315‐1050‐W 3.15 mm (.124”) 3.18mm (1/8”) 10.50 mm 38.10 mm 1,66 €

W30S208‐0320‐1050‐W 3.20 mm (.126”) 3.18mm (1/8”) 10.50 mm 38.10 mm 5,03 €

W30S208‐0325‐1300‐W 3.25 mm (.128”) 3.18mm (1/8”) 13.00 mm 38.10 mm 5,03 €

W30S208‐0330‐1300‐W 3.30 mm (.130”) 3.18mm (1/8”) 13.00 mm 38.10 mm 5,03 €

W30S208‐0335‐1300‐W 3.35 mm (.132”) 3.18mm (1/8”) 13.00 mm 38.10 mm 5,03 €

W30S208‐0340‐1300‐W 3.40 mm (.134”) 3.18mm (1/8”) 13.00 mm 38.10 mm 5,03 €

W30S208‐0345‐1300‐W 3.45 mm (.136”) 3.18mm (1/8”) 13.00 mm 38.10 mm 5,03 €

W30S208‐0350‐1300‐W 3.50 mm (.138”) 3.18mm (1/8”) 13.00 mm 38.10 mm 5,03 €

W30S208‐0355‐1300‐W 3.55 mm (.140”) 3.18mm (1/8”) 13.00 mm 38.10 mm 6,15 €

W30S208‐0360‐1300‐W 3.60 mm (.142”) 3.18mm (1/8”) 13.00 mm 38.10 mm 6,15 €

W30S208‐0365‐1300‐W 3.65 mm (.144”) 3.18mm (1/8”) 13.00 mm 38.10 mm 6,15 €

W30S208‐0370‐1300‐W 3.70 mm (.146”) 3.18mm (1/8”) 13.00 mm 38.10 mm 6,15 €



W30S208‐0375‐1300‐W 3.75 mm (.148”) 3.18mm (1/8”) 13.00 mm 38.10 mm 6,15 €

W30S208‐0380‐1300‐W 3.80 mm (.150”) 3.18mm (1/8”) 13.00 mm 38.10 mm 6,15 €

W30S208‐0385‐1300‐W 3.85 mm (.152”) 3.18mm (1/8”) 13.00 mm 38.10 mm 6,15 €

W30S208‐0390‐1300‐W 3.90 mm (.154”) 3.18mm (1/8”) 13.00 mm 38.10 mm 6,15 €

W30S208‐0395‐1300‐W 3.95 mm (.156”) 3.18mm (1/8”) 13.00 mm 38.10 mm 6,15 €

W30S208‐0400‐1300‐W 4.00 mm (.158”) 3.18mm (1/8”) 13.00 mm 38.10 mm 7,27 €

W30S208‐0405‐1300‐W 4.05 mm (.160”) 3.18mm (1/8”) 13.00 mm 38.10 mm 7,27 €

W30S208‐0410‐1300‐W 4.10 mm (.161”) 3.18mm (1/8”) 13.00 mm 38.10 mm 7,27 €

W30S208‐0415‐1300‐W 4.15 mm (.163”) 3.18mm (1/8”) 13.00 mm 38.10 mm 7,27 €

W30S208‐0420‐1300‐W 4.20 mm (.165”) 3.18mm (1/8”) 13.00 mm 38.10 mm 7,27 €

W30S208‐0425‐1300‐W 4.25 mm (.167”) 3.18mm (1/8”) 13.00 mm 38.10 mm 7,27 €

W30S208‐0430‐1300‐W 4.30 mm (.169”) 3.18mm (1/8”) 13.00 mm 38.10 mm 7,27 €

W30S208‐0435‐1300‐W 4.35 mm (.171”) 3.18mm (1/8”) 13.00 mm 38.10 mm 7,27 €

W30S208‐0440‐1300‐W 4.40 mm (.173”) 3.18mm (1/8”) 13.00 mm 38.10 mm 7,27 €

W30S208‐0445‐1300‐W 4.45 mm (.175”) 3.18mm (1/8”) 13.00 mm 38.10 mm 7,27 €

W30S208‐0450‐1300‐W 4.50 mm (.177”) 3.18mm (1/8”) 13.00 mm 38.10 mm 7,27 €

W30S208‐0455‐1300‐W 4.55 mm (.179”) 3.18mm (1/8”) 13.00 mm 38.10 mm 8,39 €

W30S208‐0460‐1300‐W 4.60 mm (.181”) 3.18mm (1/8”) 13.00 mm 38.10 mm 8,39 €

W30S208‐0465‐1300‐W 4.65 mm (.183”) 3.18mm (1/8”) 13.00 mm 38.10 mm 8,39 €

W30S208‐0470‐1300‐W 4.70 mm (.185”) 3.18mm (1/8”) 13.00 mm 38.10 mm 8,39 €

W30S208‐0475‐1300‐W 4.75 mm (.187”) 3.18mm (1/8”) 13.00 mm 38.10 mm 8,39 €

W30S208‐0480‐1300‐W 4.80 mm (.189”) 3.18mm (1/8”) 13.00 mm 38.10 mm 8,39 €

W30S208‐0485‐1300‐W 4.85 mm (.191”) 3.18mm (1/8”) 13.00 mm 38.10 mm 8,39 €

W30S208‐0490‐1300‐W 4.90 mm (.193”) 3.18mm (1/8”) 13.00 mm 38.10 mm 8,39 €

W30S208‐0495‐1300‐W 4.95 mm (.195”) 3.18mm (1/8”) 13.00 mm 38.10 mm 8,39 €

W30S208‐0500‐1300‐W 5.00 mm (.197”) 3.18mm (1/8”) 13.00 mm 38.10 mm 8,39 €

W30S208‐0505‐1300‐W 5.05 mm (.199”) 3.18mm (1/8”) 13.00 mm 38.10 mm 9,51 €

W30S208‐0510‐1300‐W 5.10 mm (.201”) 3.18mm (1/8”) 13.00 mm 38.10 mm 9,51 €

W30S208‐0515‐1300‐W 5.15 mm (.203”) 3.18mm (1/8”) 13.00 mm 38.10 mm 9,51 €

W30S208‐0520‐1300‐W 5.20 mm (.205”) 3.18mm (1/8”) 13.00 mm 38.10 mm 9,51 €

W30S208‐0525‐1300‐W 5.25 mm (.207”) 3.18mm (1/8”) 13.00 mm 38.10 mm 9,51 €

W30S208‐0530‐1300‐W 5.30 mm (.209”) 3.18mm (1/8”) 13.00 mm 38.10 mm 9,51 €

W30S208‐0535‐1300‐W 5.35 mm (.211”) 3.18mm (1/8”) 13.00 mm 38.10 mm 9,51 €

W30S208‐0540‐1300‐W 5.40 mm (.213”) 3.18mm (1/8”) 13.00 mm 38.10 mm 9,51 €

W30S208‐0545‐1300‐W 5.45 mm (.215”) 3.18mm (1/8”) 13.00 mm 38.10 mm 9,51 €

W30S208‐0550‐1300‐W 5.50 mm (.217”) 3.18mm (1/8”) 13.00 mm 38.10 mm 9,51 €

W30S208‐0555‐1300‐W 5.55 mm (.219”) 3.18mm (1/8”) 13.00 mm 38.10 mm 10,62 €

W30S208‐0560‐1300‐W 5.60 mm (.220”) 3.18mm (1/8”) 13.00 mm 38.10 mm 10,62 €

W30S208‐0565‐1300‐W 5.65 mm (.222”) 3.18mm (1/8”) 13.00 mm 38.10 mm 10,62 €

W30S208‐0570‐1300‐W 5.70 mm (.224”) 3.18mm (1/8”) 13.00 mm 38.10 mm 10,62 €

W30S208‐0575‐1300‐W 5.75 mm (.226”) 3.18mm (1/8”) 13.00 mm 38.10 mm 10,62 €

W30S208‐0580‐1300‐W 5.80 mm (.228”) 3.18mm (1/8”) 13.00 mm 38.10 mm 10,62 €

W30S208‐0585‐1300‐W 5.85 mm (.230”) 3.18mm (1/8”) 13.00 mm 38.10 mm 10,62 €

W30S208‐0590‐1300‐W 5.90 mm (.232”) 3.18mm (1/8”) 13.00 mm 38.10 mm 10,62 €

W30S208‐0595‐1300‐W 5.95 mm (.234”) 3.18mm (1/8”) 13.00 mm 38.10 mm 10,62 €

W30S208‐0600‐1300‐W 6.00 mm (.236”) 3.18mm (1/8”) 13.00 mm 38.10 mm 10,62 €

W30S208‐0605‐1300‐W 6.05 mm (.238”) 3.18mm (1/8”) 13.00 mm 38.10 mm 11,74 €

W30S208‐0610‐1300‐W 6.10 mm (.240”) 3.18mm (1/8”) 13.00 mm 38.10 mm 11,74 €

W30S208‐0615‐1300‐W 6.15 mm (.242”) 3.18mm (1/8”) 13.00 mm 38.10 mm 11,74 €

W30S208‐0620‐1300‐W 6.20 mm (.244”) 3.18mm (1/8”) 13.00 mm 38.10 mm 11,74 €

W30S208‐0625‐1300‐W 6.25 mm (.246”) 3.18mm (1/8”) 13.00 mm 38.10 mm 11,74 €

W30S208‐0630‐1300‐W 6.30 mm (.248”) 3.18mm (1/8”) 13.00 mm 38.10 mm 11,74 €

W30S208‐0635‐1300‐W 6.35 mm (.250”) 3.18mm (1/8”) 13.00 mm 38.10 mm 11,74 €

W30S208‐0640‐1300‐W 6.40 mm (.252”) 3.18mm (1/8”) 13.00 mm 38.10 mm 11,74 €

W30S208‐0645‐1300‐W 6.45 mm (.254”) 3.18mm (1/8”) 13.00 mm 38.10 mm 11,74 €

W30S208‐0650‐1300‐W 6.50 mm (.256”) 3.18mm (1/8”) 13.00 mm 38.10 mm 11,74 €



ProMetric, 2-flute 30° SL, V-drill point, slot drill bit - shank 3,18 mm (1/8")

Drill Bits

Specifications: Benefits: Geometry - 2 flute, drill point

0.50÷2.00 mm - strong 30° Overall Length - OAL - 38.10 mm ±0.25 mm Flute dia - d - nominal +0.00 -0.005 mm

Shank dia - D - 3.175 mm +0.00 -0.005 mm Helix angle - 30° Point angle - 130°

Runout - TIR - max. 0.005 mm Depth Of Cut - DOC - nominal ±0.20 mm Material - solid carbide/steel shank Operating CNC - 20k÷180k RPM

Country of Origin - Germany

Excellent suitable to manufacture precise slots

To be used for standard multilayer PCBs, stands out for good chip removal




FR2, FR3, FR4, PTFE, Aramid, CEM3 Slotting hardwoods, composites, non-ferrous metals

Slotting printed circuit substrates


WS30S208‐0050‐0500‐W 0.50 mm (.020”) 3.18mm (1/8”) 5.00 mm 38.10 mm 2,10 €

WS30S208‐0055‐0500‐W 0.55 mm (.022”) 3.18mm (1/8”) 5.00 mm 38.10 mm 2,10 €

WS30S208‐0060‐0700‐W 0.60 mm (.024”) 3.18mm (1/8”) 7.00 mm 38.10 mm 2,10 €

WS30S208‐0065‐0700‐W 0.65 mm (.026”) 3.18mm (1/8”) 7.00 mm 38.10 mm 2,10 €

WS30S208‐0070‐0850‐W 0.70 mm (.028”) 3.18mm (1/8”) 8.50 mm 38.10 mm 2,10 €

WS30S208‐0075‐0850‐W 0.75 mm (.030”) 3.18mm (1/8”) 8.50 mm 38.10 mm 2,10 €

WS30S208‐0080‐0850‐W 0.80 mm (.032”) 3.18mm (1/8”) 8.50 mm 38.10 mm 2,10 €

WS30S208‐0085‐0850‐W 0.85 mm (.034”) 3.18mm (1/8”) 8.50 mm 38.10 mm 2,10 €

WS30S208‐0090‐0850‐W 0.90 mm (.035”) 3.18mm (1/8”) 8.50 mm 38.10 mm 2,10 €

WS30S208‐0095‐0850‐W 0.95 mm (.037”) 3.18mm (1/8”) 8.50 mm 38.10 mm 2,10 €

WS30S208‐0100‐0850‐W 1.00 mm (.039”) 3.18mm (1/8”) 8.50 mm 38.10 mm 2,10 €

WS30S208‐0105‐0850‐W 1.05 mm (.041”) 3.18mm (1/8”) 8.50 mm 38.10 mm 2,10 €

WS30S208‐0110‐0850‐W 1.10 mm (.043”) 3.18mm (1/8”) 8.50 mm 38.10 mm 2,10 €

WS30S208‐0115‐0850‐W 1.15 mm (.045”) 3.18mm (1/8”) 8.50 mm 38.10 mm 2,10 €

WS30S208‐0120‐0850‐W 1.20 mm (.047”) 3.18mm (1/8”) 8.50 mm 38.10 mm 2,10 €

WS30S208‐0125‐0850‐W 1.25 mm (.049”) 3.18mm (1/8”) 8.50 mm 38.10 mm 2,10 €

WS30S208‐0130‐0850‐W 1.30 mm (.051”) 3.18mm (1/8”) 8.50 mm 38.10 mm 2,10 €

WS30S208‐0135‐0850‐W 1.35 mm (.053”) 3.18mm (1/8”) 8.50 mm 38.10 mm 2,10 €

WS30S208‐0140‐0850‐W 1.40 mm (.055”) 3.18mm (1/8”) 8.50 mm 38.10 mm 2,10 €

WS30S208‐0145‐0850‐W 1.45 mm (.057”) 3.18mm (1/8”) 8.50 mm 38.10 mm 2,10 €

WS30S208‐0150‐0850‐W 1.50 mm (.059”) 3.18mm (1/8”) 8.50 mm 38.10 mm 2,10 €

WS30S208‐0155‐0850‐W 1.55 mm (.061”) 3.18mm (1/8”) 8.50 mm 38.10 mm 2,10 €

WS30S208‐0160‐0850‐W 1.60 mm (.063”) 3.18mm (1/8”) 8.50 mm 38.10 mm 2,10 €

WS30S208‐0165‐0850‐W 1.65 mm (.065”) 3.18mm (1/8”) 8.50 mm 38.10 mm 2,10 €

WS30S208‐0170‐0850‐W 1.70 mm (.067”) 3.18mm (1/8”) 8.50 mm 38.10 mm 2,10 €

WS30S208‐0175‐0850‐W 1.75 mm (.069”) 3.18mm (1/8”) 8.50 mm 38.10 mm 2,10 €

WS30S208‐0180‐0850‐W 1.80 mm (.071”) 3.18mm (1/8”) 8.50 mm 38.10 mm 2,10 €

WS30S208‐0185‐0850‐W 1.85 mm (.073”) 3.18mm (1/8”) 8.50 mm 38.10 mm 2,10 €

WS30S208‐0190‐0850‐W 1.90 mm (.075”) 3.18mm (1/8”) 8.50 mm 38.10 mm 2,10 €

WS30S208‐0195‐0850‐W 1.95 mm (.077”) 3.18mm (1/8”) 8.50 mm 38.10 mm 2,10 €

WS30S208‐0200‐0850‐W 2.00 mm (.079”) 3.18mm (1/8”) 8.50 mm 38.10 mm 2,10 €



Diamond Cut flutes, fish tail, router - shank 3,18 mm (1/8")

Specifications: Benefits: Router B

its

Geometry – 6 diamond-cut flutes, fish tail



Baltic birch plywood - min. 500 rm Material – solid submicrograin carbide Operating CNC – 20k÷60k RPM Country of Origin – USA


Diamond grind produces smooth sidewalls with minimal top edge burr formation

Applications: De-paneling printed circuit boards Contour cutting internal pockets in PCB substrates Shaping reconstituted minerals (high mineral to resin

ratio) Cutting sheet composites


SD08‐0080‐0650‐M 0.80 mm (.0313”) 3.18mm (1/8”) 6.50 mm 38.10 mm 4,53 € 41,24 €

SD08‐0100‐0650‐M 1.00 mm (.0394”) 3.18mm (1/8”) 6.50 mm 38.10 mm 4,53 € 41,24 €

SD08‐0110‐0650‐M 1.10 mm (.0433”) 3.18mm (1/8”) 6.50 mm 38.10 mm 4,53 € 41,24 €

SD08‐0120‐0650‐M 1.20 mm (.0472”) 3.18mm (1/8”) 6.50 mm 38.10 mm 4,53 € 41,24 €

SD08‐0127‐0650‐M 1.27 mm (.0500”) 3.18mm (1/8”) 6.50 mm 38.10 mm 4,53 € 41,24 €

SD08‐0150‐0800‐M 1.50 mm (.0591”) 3.18mm (1/8”) 8.00 mm 38.10 mm 4,53 € 41,24 €

SD08‐0160‐0800‐M 1.60 mm (.0630”) 3.18mm (1/8”) 8.00 mm 38.10 mm 4,53 € 41,24 €

SD08‐0180‐0800‐M 1.80 mm (.0709”) 3.18mm (1/8”) 8.00 mm 38.10 mm 4,53 € 41,24 €

SD08‐0190‐0800‐M 1.90 mm (.0748”) 3.18mm (1/8”) 8.00 mm 38.10 mm 4,53 € 41,24 €

SD08‐0200‐0800‐M 2.00 mm (.0787”) 3.18mm (1/8”) 8.00 mm 38.10 mm 4,53 € 41,24 €

SD08‐0240‐1000‐M 2.40 mm (.0945”) 3.18mm (1/8”) 10.00 mm 38.10 mm 4,53 € 41,24 €

SD08‐0250‐1100‐M 2.50 mm (.0984”) 3.18mm (1/8”) 11.00 mm 38.10 mm 4,53 € 41,24 €

SD08‐0300‐1100‐M 3.00 mm (.1181”) 3.18mm (1/8”) 11.00 mm 38.10 mm 4,53 € 41,24 €

SD08‐0318‐1200‐M 3.18 mm (.1250”) 3.18mm (1/8”) 12.00 mm 38.10 mm 4,53 € 41,24 €



Diamond Cut flutes M30, fish tail, router - shank 3,18 mm (1/8")

Router Bits

Specifications: Benefits: Geometry - fine diamond-cut flutes, fish tail





Diamond grind produces smooth sidewalls with minimal top edge burr formation

Applications: PCB: FR2, FR3, FR4, Polyimide, high Tg resins De-paneling printed circuit boards Contour cutting internal pockets in PCB substrates Shaping reconstituted minerals (high mineral to resin ratio)

Cutting sheet composites


MSD08‐0060‐0300‐M 0.60 mm (.0236”) 3.18mm (1/8”) 3.00 mm 38.10 mm 3,20 €

MSD08‐0070‐0400‐M 0.70 mm (.0275”) 3.18mm (1/8”) 4.00 mm 38.10 mm 3,20 €

MSD08‐0080‐0500‐M 0.80 mm (.0313”) 3.18mm (1/8”) 5.00 mm 38.10 mm 3,20 €

MSD08‐0080‐0700‐M 0.80 mm (.0313”) 3.18mm (1/8”) 7.00 mm 38.10 mm 3,20 €

MSD08‐0090‐0500‐M 0.90 mm (.0354”) 3.18mm (1/8”) 5.00 mm 38.10 mm 3,20 €

MSD08‐0090‐0700‐M 0.90 mm (.0354”) 3.18mm (1/8”) 7.00 mm 38.10 mm 3,20 €

MSD08‐0100‐0500‐M 1.00 mm (.0394”) 3.18mm (1/8”) 5.00 mm 38.10 mm 3,20 €

MSD08‐0100‐0700‐M 1.00 mm (.0394”) 3.18mm (1/8”) 7.00 mm 38.10 mm 3,20 €

MSD08‐0110‐0500‐M 1.10 mm (.0433”) 3.18mm (1/8”) 5.00 mm 38.10 mm 3,20 €

MSD08‐0110‐0700‐M 1.10 mm (.0433”) 3.18mm (1/8”) 7.00 mm 38.10 mm 3,20 €

MSD08‐0120‐0700‐M 1.20 mm (.0472”) 3.18mm (1/8”) 7.00 mm 38.10 mm 3,20 €

MSD08‐0130‐0700‐M 1.30 mm (.0512”) 3.18mm (1/8”) 7.00 mm 38.10 mm 3,20 €

MSD08‐0140‐0700‐M 1.40 mm (.0551”) 3.18mm (1/8”) 7.00 mm 38.10 mm 3,20 €

MSD08‐0150‐0700‐M 1.50 mm (.0591”) 3.18mm (1/8”) 8.00 mm 38.10 mm 3,20 €

MSD08‐0160‐0800‐M 1.60 mm (.0630”) 3.18mm (1/8”) 8.00 mm 38.10 mm 3,20 €

MSD08‐0170‐0800‐M 1.70 mm (.0669”) 3.18mm (1/8”) 8.00 mm 38.10 mm 3,20 €

MSD08‐0180‐0800‐M 1.80 mm (.0709”) 3.18mm (1/8”) 8.00 mm 38.10 mm 3,20 €

MSD08‐0190‐0800‐M 1.90 mm (.0748”) 3.18mm (1/8”) 8.00 mm 38.10 mm 3,20 €

MSD08‐0200‐0900‐M 2.00 mm (.0787”) 3.18mm (1/8”) 9.00 mm 38.10 mm 3,20 €

MSD08‐0200‐1000‐M 2.00 mm (.0787”) 3.18mm (1/8”) 10.00 mm 38.10 mm 3,20 €

MSD08‐0210‐0900‐M 2.10 mm (.0826”) 3.18mm (1/8”) 9.00 mm 38.10 mm 3,20 €

MSD08‐0220‐0900‐M 2.20 mm (.0866”) 3.18mm (1/8”) 9.00 mm 38.10 mm 3,20 €

MSD08‐0230‐0900‐M 2.30 mm (.0905”) 3.18mm (1/8”) 9.00 mm 38.10 mm 3,20 €

MSD08‐0240‐0900‐M 2.40 mm (.0945”) 3.18mm (1/8”) 9.00 mm 38.10 mm 3,20 €

MSD08‐0240‐1000‐M 2.40 mm (.0945”) 3.18mm (1/8”) 10.00 mm 38.10 mm 3,20 €

**AAll ll pprriicceess aarree iinn EEUURR ((€€))


Chip Breaker flute grind, fish tail, router – shank 3,18 mm (1/8”)

Specifications: Benefits: Router B

its

Geometry – chip-breaker flute grind, fish tail



Baltic birch plywood - min. 500 rm Material – solid submicrograin carbide Operating CNC – 20k÷60k RPM Country of Origin – USA


Chip-breaker grind combines aggressive cutting action with high flute volume for enhanced swarf removal

Applications: De-paneling printed circuit boards Contour cutting internal pockets in PCB substrates Shaping reconstituted minerals



SC08‐0080‐0650‐M 0.80 mm (.0313”) 3.18mm (1/8”) 6.50 mm 38.10 mm 4,53 € 41,24 €

SC08‐0100‐0650‐M 1.00 mm (.0394”) 3.18mm (1/8”) 6.50 mm 38.10 mm 4,53 € 41,24 €

SC08‐0110‐0650‐M 1.10 mm (.0433”) 3.18mm (1/8”) 6.50 mm 38.10 mm 4,53 € 41,24 €

SC08‐0120‐0650‐M 1.20 mm (.0472”) 3.18mm (1/8”) 6.50 mm 38.10 mm 4,53 € 41,24 €

SC08‐0130‐0650‐M 1.30 mm (.0512”) 3.18mm (1/8”) 6.50 mm 38.10 mm 4,53 € 41,24 €

SC08‐0150‐0800‐M 1.50 mm (.0591”) 3.18mm (1/8”) 8.00 mm 38.10 mm 4,53 € 41,24 €

SC08‐0160‐0800‐M 1.60 mm (.0630”) 3.18mm (1/8”) 8.00 mm 38.10 mm 4,53 € 41,24 €

SC08‐0180‐0800‐M 1.80 mm (.0709”) 3.18mm (1/8”) 8.00 mm 38.10 mm 4,53 € 41,24 €

SC08‐0190‐0800‐M 1.90 mm (.0748”) 3.18mm (1/8”) 8.00 mm 38.10 mm 4,53 € 41,24 €

SC08‐0200‐0800‐M 2.00 mm (.0787”) 3.18mm (1/8”) 8.00 mm 38.10 mm 4,53 € 41,24 €

SC08‐0240‐1000‐M 2.40 mm (.0945”) 3.18mm (1/8”) 10.00 mm 38.10 mm 4,53 € 41,24 €

SC08‐0250‐1100‐M 2.50 mm (.0984”) 3.18mm (1/8”) 11.00 mm 38.10 mm 4,53 € 41,24 €

SC08‐0300‐1100‐M 3.00 mm (.1181”) 3.18mm (1/8”) 11.00 mm 38.10 mm 4,53 € 41,24 €

SC08‐0318‐1200‐M 3.18 mm (.1250”) 3.18mm (1/8”) 12.00 mm 38.10 mm 4,53 € 41,24 €



Chip Breaker flute grind M20, fish tail, router - shank 3,18 mm (1/8")

Router Bits

Specifications: Benefits: Geometry - chip-breaker flute grind, fish tail





Chip-breaker grind combines aggressive cutting action with high flute volume for enhanced swarf removal

Applications: PCB: FR2, FR3, FR4, CEM3, PTFE, Aramide De-paneling printed circuit boards Contour cutting internal pockets in PCB substrates Shaping reconstituted minerals



MSC08‐0060‐0300‐M 0.60 mm (.0236”) 3.18mm (1/8”) 3.00 mm 38.10 mm 3,20 €

MSC08‐0070‐0300‐M 0.70 mm (.0275”) 3.18mm (1/8”) 3.00 mm 38.10 mm 3,20 €

MSC08‐0080‐0500‐M 0.80 mm (.0313”) 3.18mm (1/8”) 5.00 mm 38.10 mm 3,20 €

MSC08‐0080‐0700‐M 0.80 mm (.0313”) 3.18mm (1/8”) 7.00 mm 38.10 mm 3,20 €

MSC08‐0090‐0500‐M 0.90 mm (.0354”) 3.18mm (1/8”) 5.00 mm 38.10 mm 3,20 €

MSC08‐0090‐0700‐M 0.90 mm (.0354”) 3.18mm (1/8”) 7.00 mm 38.10 mm 3,20 €

MSC08‐0100‐0500‐M 1.00 mm (.0394”) 3.18mm (1/8”) 5.00 mm 38.10 mm 3,20 €

MSC08‐0100‐0700‐M 1.00 mm (.0394”) 3.18mm (1/8”) 7.00 mm 38.10 mm 3,20 €

MSC08‐0110‐0500‐M 1.10 mm (.0433”) 3.18mm (1/8”) 5.00 mm 38.10 mm 3,20 €

MSC08‐0110‐0700‐M 1.10 mm (.0433”) 3.18mm (1/8”) 7.00 mm 38.10 mm 3,20 €

MSC08‐0120‐0700‐M 1.20 mm (.0472”) 3.18mm (1/8”) 7.00 mm 38.10 mm 3,20 €

MSC08‐0130‐0700‐M 1.30 mm (.0512”) 3.18mm (1/8”) 7.00 mm 38.10 mm 3,20 €

MSC08‐0140‐0700‐M 1.40 mm (.0551”) 3.18mm (1/8”) 7.00 mm 38.10 mm 3,20 €

MSC08‐0150‐0800‐M 1.50 mm (.0591”) 3.18mm (1/8”) 8.00 mm 38.10 mm 3,20 €

MSC08‐0160‐0800‐M 1.60 mm (.0630”) 3.18mm (1/8”) 8.00 mm 38.10 mm 3,20 €

MSC08‐0170‐0800‐M 1.70 mm (.0669”) 3.18mm (1/8”) 8.00 mm 38.10 mm 3,20 €

MSC08‐0180‐0800‐M 1.80 mm (.0709”) 3.18mm (1/8”) 8.00 mm 38.10 mm 3,20 €

MSC08‐0190‐0800‐M 1.90 mm (.0748”) 3.18mm (1/8”) 8.00 mm 38.10 mm 3,20 €

MSC08‐0200‐0900‐M 2.00 mm (.0787”) 3.18mm (1/8”) 9.00 mm 38.10 mm 3,20 €

MSC08‐0200‐1000‐M 2.00 mm (.0787”) 3.18mm (1/8”) 10.00 mm 38.10 mm 3,20 €

MSC08‐0210‐0900‐M 2.10 mm (.0826”) 3.18mm (1/8”) 9.00 mm 38.10 mm 3,20 €

MSC08‐0220‐0900‐M 2.20 mm (.0866”) 3.18mm (1/8”) 9.00 mm 38.10 mm 3,20 €

MSC08‐0230‐0900‐M 2.30 mm (.0905”) 3.18mm (1/8”) 9.00 mm 38.10 mm 3,20 €

MSC08‐0240‐0900‐M 2.40 mm (.0945”) 3.18mm (1/8”) 9.00 mm 38.10 mm 3,20 €

MSC08‐0240‐1000‐M 2.40 mm (.0945”) 3.18mm (1/8”) 10.00 mm 38.10 mm 3,20 €

**AAll ll pprriicceess aarree iinn EEUURR ((€€))


ProMetric, 1-flute, V-point, Engraving - shank 3,18 mm (1/8")

Specifications: Benefits: Engravin

g Tools

Geometry - 1 flute, V-point

Overall Length - OAL - nominal ±0.10 mm Flute dia - d - 3.175 mm +0.01 -0.02 mm Shank dia - D - 3.175 mm +0.00 -0.005 mm

Tip angle - KO - ±0.5° Runout - TIR - max. 0.005 mm Depth Of Cut - DOC - nominal ±0.10 mm:

22.5° V-point - 7.98 mm 30° V-point - 5.92 mm 45° V-point - 3.83 mm 60° V-point - 2.75 mm 90° V-point - 1.59 mm

Material - solid submicrograin carbide Operating CNC - 30k÷80k RPM

Country of Origin - Germany


Applications: Print circuit trace isolation

Engraving plaques, awards, medallions, and labels Custom jewelry fabrication and marking


G1G8‐0318‐K022‐V 3.18 mm (.1250”) 3.18mm (1/8”) 22.5° V‐point 38.10 mm 13,42 €

G1G8‐0318‐K030‐V 3.18 mm (.1250”) 3.18mm (1/8”) 30° V‐point 38.10 mm 13,42 €





Pro, 2-flute, V-point, Engraving/Countersink – shank 3,18 mm (1/8”)

Specifications: Benefits: Engravin

g Tools

Geometry – 2 flute, V-point Overall Length – OAL – nominal ±0.25 mm

Flute dia – d – nominal +0.00 -0.05 mm Shank dia – D – 3.175 mm +0.00 -0.005 mm Tip angle – KO – ±0.5°

Runout – TIR – max. 0.005 mm Depth Of Cut – DOC – nominal ±0.10 mm:

30° V-point – 4.50 mm 45° V-point – 1.92 mm 60° V-point – 1.83 mm 90° V-point – 0.80 mm

Anticipated Life:

Baltic birch plywood - min. 500 rm Material – solid submicrograin carbide Operating CNC – 20k÷100k RPM


Spiral geometry insures efficient debris removal Cutting edge geometry virtually eliminates chatter at high

feed rates 30° tip designed for scrimshaw engraving in ivory, horn,

phenolics, and all hardwoods. Not optimized for metal engraving

60° & 90° tips optimized for engraving non-ferrous metals, hardwoods, phenolics, stabilized woods and composite minerals

Proprietary ZrN (Zirconium Nitride) coating extends bit life and improves cut quality

Applications: Print circuit trace isolation Engraving plaques, awards, medallions, and labels Custom jewelry fabrication and marking


G2G8‐0241‐K030‐V ‐ 2.41 mm (.0950”) 3.18mm (1/8”) 30° V‐point 38.10 mm 8,01 € 72,88 €




G2G8‐0241‐K030‐VZ ZrN 2.41 mm (.0950”) 3.18mm (1/8”) 30° V‐point 38.10 mm 11,14 € 101,41 €






Pro, 4-flute, V-point, Engraving/Countersink – shank 3,18 mm (1/8”)

Engraving To

ols

Specifications: Benefits: Geometry – 4 flute, V-point

Overall Length – OAL – 38.10 mm ±0.25 mm Flute dia – d – 6.35 mm +0.00 -0.05 mm Shank dia – D – 3.175 mm +0.00 -0.005 mm

Tip angle – KO – ±0.5° Runout – TIR – max. 0.005 mm Depth Of Cut – DOC – nominal ±0.10 mm:

60° V-punkt – 5.50 mm 90° V-punkt – 3.18 mm 100° V-punkt – 2.66 mm 120° V-punkt – 1.83 mm




4-flute plunge tip insures long life and quiet operation


Optimized for scoring, beveling, carving and engraving non-ferrous metals, hardwoods, phenolics, stabilized woods and composite minerals


Engraving plaques, awards, medallions, and labels PCB beveling and countersinking Custom jewelry fabrication and marking


G4G8‐0635‐K060‐V 6.35 mm (.2500”) 3.18mm (1/8”) 60° V‐point 38.10 mm 25,89 € ‐





Ultra, 2-flute spiral, V-Skiving, end mill - shank 3,18 mm (1/8")

Engraving To

ols

Specifications: Benefits: Geometry – 2 flute spiral, V-point Overall Length – OAL – 38.10 mm ±0.25 mm Flute dia – d – 3.175 mm +0.00 -0.05 mm

Shank dia – D – 3.175 mm +0.00 -0.005 mm Tip angle – KO – ±1.0° Runout – TIR – max. 0.005 mm Depth Of Cut – DOC –

30° V-point – 5.92 mm ±0.10 mm 45° V-point – 3.83 mm ±0.10 mm 60° V-point – 2.75 mm ±0.10 mm 90° V-point – 1.59 mm ±0.10 mm

Anticipated Life: Depends on material – min 150 rm

(fiberglass) Material – solid submicrograin carbide Operating CNC – 20k÷100k RPM


Cuts counter board substrates at 65-105 mm/s @ 40,000 RPM

Cutting edge geometry virtually top edge lifting and fraying

True spiral geometry insures efficient debris removal 30°, 45°, 60° & 90° tips optimized for chamfering and

through-cutting glass-phenolic and paper-phenolic counter board substrates


Engraving plaques, awards, medallions, and labels PCB beveling and countersinking Custom jewelry fabrication and marking


F2W8‐0318‐K030‐V ‐ 3.18 mm (.1250”) 3.18 mm (1/8”) 30° V‐point 38.10 mm 11,41 € 103,83 €




F2W8‐0318‐K030‐VZ ZrN 3.18 mm (.1250”) 3.18 mm (1/8”) 30° V‐point 38.10 mm 14,55 € 132,44 €






Ultra, 2-flute, Horn/Ivory Cutter, fish tail, end-mill – shank 3,18 mm (1/8”)

Specifications: Benefits: Specialty To

ols



Helix angle – 28° Runout – TIR – max. 0.005 mm Depth Of Cut – DOC – 3.68 mm ±0.10 mm





High flute volume supports high feed rates / chip loads Cutting edge geometry tuned to all aspects of inlay pocket

cutting and component shaping

Applications: Cutting inlay and intarsia components from antler, horn,

ivory, phenolic, and stabilized mineral products Pocket cutting in ebony, rosewood, and purpleheart

Engraving horn, ivory, antler, hardwood and phenolics Slotting printed circuit board substrates Machining thermoplastics for engineering and medical

applications


F2IK8‐0080‐0368‐M 0.80 mm (.0313”) 3.18mm (1/8”) 3.68 mm 38.10 mm 9,72 € 88,44 €


Ultra, 3-flute, Shell Cutter, fish tail, end-mill – shank 3,18 mm (1/8”)

Specifications: Benefits: Specialty To

ols

Geometry – 3 flute, fish tail, chip breaker grind

Overall Length – OAL – 38.10 mm ±0.25 mm Flute dia – d – nominalnie +0.00 -0.05 mm Shank dia – D – 3.175 mm +0.00 -0.005 mm

Helix angle – 28° Runout – TIR – max. 0.005 mm Depth Of Cut – DOC – 2.54 mm ±0.10 mm





High flute volume supports high feed rates / chip loads 3-Flute design eliminates chatter at high feed rates

3-Flute design brings the rigidity and precision of a stub mill to a high-aspect ratio milling cutter

Chip breaker cutting edge geometry designed for efficient debris removal and smooth side wall formation

Applications: Mother of pearl logos for musical instruments Pool cue inlay parts and pockets

Pool table sights Custom cabinetry Entarsia

Item# Flute Dia. ‐ d Shank Dia. ‐ D D‐h of Cut Length ‐ OAL Price* 10‐packs*

F3IM8‐0040‐0152‐M 0.40 mm (.0156”) 3.18mm (1/8”) 1.52 mm 38.10 mm 20,42 € 185,78 €

F3IM8‐0051‐0200‐M 0.51 mm (.0200”) 3.18mm (1/8”) 2.00 mm 38.10 mm 19,23 € 174,97 €

F3IM8‐0064‐0254‐M 0.64 mm (.0250”) 3.18mm (1/8”) 2.54 mm 38.10 mm 17,28 € 157,25 €

F3IM8‐0080‐0254‐M 0.80 mm (.0313”) 3.18mm (1/8”) 2.54 mm 38.10 mm 10,40 € 94,66 €

F3IM8‐0080‐0318‐M 0.80 mm (.0313”) 3.18mm (1/8”) 3.18 mm 38.10 mm 15,15 € 137,89 €

F3IM8‐0159‐0318‐M 1.59 mm (.0625”) 3.18mm (1/8”) 3.18 mm 38.10 mm 11,88 € 108,15 €



Ultra, 5-flute, SRD Cutters, fish tail, end-mill – shank 3,18 mm (1/8”)

Steel R

ule Dies

Specifications: Benefits: Geometry – 5 flute, Blended Helix®, fish tail

Overall Length – OAL – 38.10 mm ±0.25 mm Flute dia – d –

1.3 pt - 0.46 mm ±0.01 mm 1.5 pt – 0.53 mm ±0.01 mm 2 pt – 0.71 mm ±0.01 mm 3 pt – 1.05 mm ±0.01 mm 4 pt – 1.42 mm ±0.01 mm 6 pt – 2.13 mm ±0.01 mm

Shank dia – D – 3.175 mm +0.00 -0.005 mm

Deflection compensation – ±0.05-0.10 mm Runout – TIR – max. 0.005 mm Depth Of Cut – DOC –

9.70 mm (0.380”) ±0.10 mm 11.70 mm (0.460”) ±0.10 mm

Parallel (drag) kerf depth – 2.50 mm Anticipated Life: Depends on material b/g cut

8 mm birch plywood – 380-500 rm (max.700) 8 mm maple plywood – 180-300 rm



Cuts 8 mm Baltic birch plywood at 40-60 mm/s @ 40,000 RPM

9.70 mm tools are available with CloseKerf© flute geometry for unprecedented closeness in rule placement

Variable helix design provides more efficient chip extraction and minimizes top surface fuzz and splintering

Our 2 point kerf cutters have been designed to meet the varying needs of diemakers working in different areas of the packaging industry The "Low-deflection" bit is optimized to cut at 50-60 mm/s

@ 40,000 RPM with less than 0.10 mm tip deflection The "Close-kerf" tool has been designed to allow rule

placement on 2.54 mm centers (8 mm Baltic birch plywood) with a tip deflection of less than 0.10 mm while cutting at 40-45 mm/s @ 40,000 RPM.

Both tools retain the long life and superior debris removal that are the hallmarks of this family of tools

Applications: Cutting kerf slots in steel-rule die-boards Clean-up cutter for fine inlay pocket finishing

Item# Description Flute Dia. ‐ d D‐h of Cut Price* 10‐packs*

F5W8‐0044‐1170‐MU Extra Narrow‐kerf, Low‐deflection 1.3pt–0.44 mm 11.70 mm 48,07 € 437,40 €

F5W8‐0045‐1170‐MU Narrow‐kerf, Low‐deflection 1.3pt–0.45 mm 11.70 mm 48,07 € 437,40 €

F5W8‐0046‐1170‐MU Normal‐kerf, Low‐deflection 1.3pt–0.46 mm 11.70 mm 48,07 € 437,40 €



F5W8‐0054‐1170‐MU Wide‐kerf, Low‐deflection 1.5pt–0.54 mm 11.70 mm 48,07 € 437,40 €



F5W8‐0093‐1170‐MU Wide‐kerf, Low‐deflection 2.6pt–0.93 mm 11.70 mm 48,07 € 437,40 €

F5W8‐0061‐1170‐CO Kerf Clean‐out Tool 2pt–0.61 mm 11.70 mm 15,71 € 142,99 €

F5W8‐0069‐1170‐MU Extra Narrow‐kerf, Low‐deflection 2pt–0.69 mm 11.70 mm 48,07 € 437,40 €

F5W8‐0070‐1170‐MU Narrow‐kerf, Low‐deflection 2pt–0.70 mm 11.70 mm 48,07 € 437,40 €

F5W8‐0071‐0970‐MS Normal‐Close‐kerf 2pt–0.71 mm 9.70 mm 48,07 € 437,40 €

F5W8‐0071‐1170‐MUZ Normal‐kerf, ZrN coated, Low‐deflection 2pt–0.71 mm 11.70 mm 48,07 € 437,40 €

F5W8‐0071‐1170‐MU Normal‐kerf, Low‐deflection 2pt–0.71 mm 11.70 mm 48,07 € 437,40 €

F5W8‐0072‐0970‐MS Wide‐Close‐kerf 2pt–0.72 mm 9.70 mm 48,07 € 437,40 €

F5W8‐0072‐1170‐MUZ Wide‐kerf, ZrN coated, Low‐deflection 2pt–0.72 mm 11.70 mm 48,07 € 437,40 €

F5W8‐0072‐1170‐MU Wide‐kerf, Low‐deflection 2pt–0.72 mm 11.70 mm 48,07 € 437,40 €


F5W8‐0074‐1170‐MU Extra Wide‐kerf, Low‐deflection 2pt–0.74 mm 11.70 mm 48,07 € 437,40 €

F5W8‐0075‐1170‐MU Ultra Wide‐kerf, Low‐deflection 2pt–0.75 mm 11.70 mm 48,07 € 437,40 €

F5W8‐0102‐1170‐MU Too Narrow‐kerf, Low‐deflection 3pt–1.02 mm 11.70 mm 48,07 € 437,40 €

F5W8‐0103‐1170‐MU Ultra Narrow‐kerf, Low‐deflection 3pt–1.03 mm 11.70 mm 48,07 € 437,40 €

F5W8‐0104‐1170‐MU Extra Narrow‐kerf, Low‐deflection 3pt–1.04 mm 11.70 mm 48,07 € 437,40 €

F5W8‐0105‐1170‐MU Narrow‐kerf, Low‐deflection 3pt–1.05 mm 11.70 mm 48,07 € 437,40 €

F5W8‐0107‐1170‐MUZ Normal‐kerf, ZrN coated, Low‐deflection 3pt–1.07 mm 11.70 mm 48,07 € 437,40 €




F5W8‐0110‐1170‐MU Ultra Wide‐kerf, Low‐deflection 3pt–1.10 mm 11.70 mm 48,07 € 437,40 €

F5W8‐0112‐1170‐MU Too Wide‐kerf, Low‐deflection 3pt–1.12 mm 11.70 mm 48,07 € 437,40 €

F5W8‐0141‐1170‐MU Ultra Narrow‐kerf, Low‐deflection 4pt–1.41 mm 11.70 mm 48,07 € 437,40 €









Ultra, 2-flute spiral, V-Skiving, end-mill – shank 3,18 mm

Specifications: Benefits: Steel R

ule Dies

Geometry – 2 flute spiral, V-point


Tip angle – KO – ±1.0° Runout – TIR – max. 0.005 mm Depth Of Cut – DOC –

30° V-point – 5.92 mm ±0.10 mm 45° V-point – 3.83 mm ±0.10 mm 60° V-point – 2.75 mm ±0.10 mm 90° V-point – 1.59 mm ±0.10 mm

Anticipated Life: counter board substrates – min 150 rm



Cuts counter board substrates at 60-100 mm/s @ 40,000 RPM

Cutting edge geometry virtually top edge lifting and fraying True spiral geometry insures efficient debris removal

30°, 45°, 60° & 90° tips optimized for chamfering and through-cutting glass-phenolic and paper-phenolic counter board substrates

Applications: Cutting the outer perimeter and hand holds for steel rule

dieboards Cutting steel rule die ejection rubber

High speed cutting of softwoods Pocket roughing tool for large scale inlay











Pro, 3-flute straight, Channel, fish tail, end-mill – shank 3,18 mm (1/8”)

Specifications: Benefits: Steel R

ule Dies

Geometry – 3 flute high-shear straight, fish tail



counter board substrates – min 250 rm Material – solid submicrograin carbide Operating CNC – 20k÷100k RPM Country of Origin – USA

Cuts counter board substrates at 75-85 mm/s @ 40k RPM

Shallow fish tail point insures smooth channel profile High flute volume supports high feed rates / chip loads Cutting edge geometry virtually eliminates chatter at high

feed rates Straight flute geometry eliminates lifting and gouging of the

substrate

Applications: Machining counter-board channels in matrix and composite

materials Slotting FR-4 and other electronic substrates

Engraving in thin substrates


F3W8‐0114‐0230‐M ‐ 1.14 mm (.0450”) 3.18mm (1/8”) 2.30 mm 38.10 mm 14,92 € 135,73 €

F3W8‐0114‐0230‐MZ ZrN 1.14 mm (.0450”) 3.18mm (1/8”) 2.30 mm 38.10 mm 18,05 € 164,26 €

F3W8‐0152‐0318‐M ‐ 1.52 mm (.0600”) 3.18mm (1/8”) 3.18 mm 38.10 mm 14,92 € 135,73 €

F3W8‐0152‐0318‐MZ ZrN 1.52 mm (.0600”) 3.18mm (1/8”) 3.18 mm 38.10 mm 18,05 € 164,26 €



Pro, 4-flute straight, V-Skiving, end-mill – shank 9,53 mm (3/8”)

Steel R

ule Dies

Specifications: Benefits: Geometry – 4 flute high-shear straight, extended

length, end-cutting Overall Length – OAL – 50.80 mm ±0.25 mm Flute dia – d – 9.53 mm +0.00 -0.05 mm

Shank dia – D – 9.53 mm +0.00 -0.005 mm Tip angle – KO – ±0.5° Runout – TIR – max. 0.005 mm

Depth Of Cut – DOC – 155° V-point – 1.05 mm ±0.10 mm 170° V-point – 0.42 mm ±0.10 mm

Anticipated Life: counter board substrates – min 250 rm



45 mm/s @ 22.5k RPM

High flute volume supports high feed rates / chip loads Innovative split-flute, end cutting geometry significantly

reduces noise


Straight flute geometry eliminates lifting and gouging of the substrate

Applications: Skiving counter-board edges and locators Shaving FR-4 substrate edges


F4W3‐0953‐K155‐V ‐ 9.53 mm (.3750”) 9.53 mm (3/8”) 155° V‐point 50.80 mm 45,84 € ‐

F4W3‐0953‐K155‐VZ ZrN 9.53 mm (.3750”) 9.53 mm (3/8”) 155° V‐point 50.80 mm 55,34 € ‐

F4W3‐0953‐K170‐V ‐ 9.53 mm (.3750”) 9.53 mm (3/8”) 170° V‐point 50.80 mm 45,84 € ‐

F4W3‐0953‐K170‐VZ ZrN 9.53 mm (.3750”) 9.53 mm (3/8”) 170° V‐point 50.80 mm 55,34 € ‐



Ultra - Precision low-TIR ER Collets


Collets

Steel – SUJ 2

H.R.C. 46° Taper – 8° Surface Roughness Rz 2.5

Internal hole by boring machine Clamping capacity: - ER8, ER11– 0.5 mm (.020") - ER16, 20, 32, 40 – 1.0 mm (.039") Compatible with DR, RD, ESX, AR, & BR Series

Collets Degree of concentricity exceeds the DIN standard.

100% examined to 0.005 mm (.0002") TIR Country of Origin – USA (TechniksUSA)

low noise operation

longer tool life (go to the Tool Life Resource Center)

more accurate cutting and higher kerf fidelity

compatible with carbide microtools

Item# ER Type Inch Metric Range Net Price*

UP‐04216‐0318‐1/8 ER‐16 1/8" (.1250") 3.18 mm (.118 ‐ .157") 3.0‐4.0 mm 39,90 €

UP‐04216‐0476‐3/16 ER‐16 3/16" (.1875") 4.76 mm (.157 ‐ .197") 4.0‐5.0 mm 39,90 €

UP‐04216‐0635‐1/4 ER‐16 1/4" (.2500") 6.35 mm (.236 ‐ .276") 6.0‐7.0 mm 39,90 €

UP‐04216‐0953‐3/8 ER‐16 3/8" (.3750") 9.53 mm (.354 ‐ .394") 9.0‐10.0 mm 39,90 €

UP‐04220‐0318‐1/8 ER‐20 1/8" (.1250") 3.18 mm (.118 ‐ .157") 3.0‐4.0 mm 39,90 €

UP‐04220‐0476‐3/16 ER‐20 3/16" (.1875") 4.76 mm (.157 ‐ .197") 4.0‐5.0 mm 39,90 €

UP‐04220‐0635‐1/4 ER‐20 1/4" (.2500") 6.35 mm (.236 ‐ .276") 6.0‐7.0 mm 39,90 €

UP‐04220‐0953‐3/8 ER‐20 3/8" (.3750") 9.53 mm (.354 ‐ .394") 9.0‐10.0 mm 39,90 €

UP‐04220‐1270‐1/2 ER‐20 1/2" (.5000") 12.70 mm (.472 ‐ .512") 12.0‐13.0 mm 39,90 €

UP‐04225‐0318‐1/8 ER‐25 1/8" (.1250") 3.18 mm (.118 ‐ .157") 3.0‐4.0 mm 39,90 €

UP‐04225‐0476‐3/16 ER‐25 3/16" (.1875") 4.76 mm (.157 ‐ .197") 4.0‐5.0 mm 39,90 €

UP‐04225‐0635‐1/4 ER‐25 1/4" (.2500") 6.35 mm (.236 ‐ .276") 6.0‐7.0 mm 39,90 €

UP‐04225‐0953‐3/8 ER‐25 3/8" (.3750") 9.53 mm (.354 ‐ .394") 9.0‐10.0 mm 39,90 €

UP‐04225‐1270‐1/2 ER‐25 1/2" (.5000") 12.70 mm (.472 ‐ .512") 12.0‐13.0 mm 39,90 €

UP‐04232‐0318‐1/8 ER‐32 1/8" (.1250") 3.18 mm (.118 ‐ .157") 3.0‐4.0 mm 39,90 €

UP‐04232‐0476‐3/16 ER‐32 3/16" (.1875") 4.76 mm (.157 ‐ .197") 4.0‐5.0 mm 39,90 €

UP‐04232‐0635‐1/4 ER‐32 1/4" (.2500") 6.35 mm (.236 ‐ .276") 6.0‐7.0 mm 39,90 €

UP‐04232‐0953‐3/8 ER‐32 3/8" (.3750") 9.53 mm (.354 ‐ .394") 9.0‐10.0 mm 39,90 €

UP‐04232‐1270‐1/2 ER‐32 1/2" (.5000") 12.70 mm (.472 ‐ .512") 12.0‐13.0 mm 39,90 €


Ultra - Precision low-TIR ER Collet Nuts

Specifications: Benefits: Collet N

uts

used in applications where speeds exceed 10,000 PRM

balanced to G2.5 for 20,000 RPM's

used on collet holders and multi-spindle heads where center or shoulder distances are critical

Country of Origin – USA (TechniksUSA)

low noise operation longer tool life (go to the Tool Life Resource Center) more accurate cutting and higher kerf fidelity

compatible with carbide microtools

Item# ER Type Thread Net Price*

UP‐33116‐M19x1 ER‐16 M19 x 1.0 56,05 €

UP‐33120‐M24x1 ER‐20 M24 x 1.0 56,05 €

UP‐33125‐M30x1 ER‐25 M30 x 1.0 56,05 €

UP‐33132‐M30x1 ER‐32 M30 x 1.0 56,05 €



Ultra - Precision low-TIR ISO 20 ER Collet Toolholders

Toolholders

Specifications: Benefits: Balanced to 18,000 RPM @ G2.5 (Inspection

Report included for accuracy and balance) Internal (collet) Taper: 8° Surface Roughness Rz 2.5

Degree of concentricity exceeds the DIN standard. 100% examined to 0.005 mm (0.0002") TIR

Country of Origin – USA (TechniksUSA)

Low noise operation

Longer tool life More accurate cutting and higher kerf fidelity Compatible with carbide microtools

Applications: for Colombo spindle automatic tool changers shipped with collet nuts and pull studs

Item# Description ER Type Thread Price*

UP‐04622‐ER16‐W Mini‐nut hand wrench (for ER‐16M toolholder) ER‐16 ‐ 13,30 €

UP‐04623‐ER20‐W Mini‐nut hand wrench (for ER‐20M toolholder) ER‐20 ‐ 13,30 €

UP‐06000‐ER16‐ISO20 ISO 20 ‐ ER‐16 ‐ 52mm Ultra‐precision Toolholder ER‐16 M19 x 1.0 175,75 €

UP‐06000‐ER20‐ISO20 ISO 20 ‐ ER‐20 ‐ 52mm Ultra‐precision Toolholder ER‐20 M24 x 1.0 175,75 €

UP‐ER20‐PS ISO 20 Toolholder pull‐stud ‐ ‐ 26,13 €



Precision PC Spring Collets for Porter-Cable Routers


PC Collets

Steel - SUJ 2

H.R.C. 45-52 Surface Roughness - Ra 0.5 um Internal hole by boring machine

SG (standard grade) TIR < 0.015 mm (0.0006") PG (precision grade) TIR < 0.01 mm (0.0004") UP (ultra-precision grade) TIR < 0.005 mm

(0.0002") Degree of concentricity exceeds the DIN standard.

100% examined

must be used with InGraph PCPG nuts and spanners


Low noise operation


Low TIR means less wear and tear on spindle bearings

Applications: compatible with Porter-Cable:

690, 690LR, 9690LR, 691, 693, 890, 891, 892, 893, 7518, 7519, 7536, 7537, 7538, 7539 routers

Item# TIR Inch Metric Range Net Price*

PCPG‐0318‐1/8 TIR < 0.01 mm 1/8" (.1250") 3.18 mm (.118 ‐ .157") 3.0‐4.0 mm 18,95€

PCPG‐0635‐1/4 TIR < 0.01 mm 1/4" (.2500") 6.35 mm (.236 ‐ .276") 6.0‐7.0 mm 18,95€

PCPG‐0800‐5/16 TIR < 0.01 mm 5/16"(.3125") 8.00 mm ‐ 18,95€

PCPG‐1270‐1/2 TIR < 0.01 mm 1/2" (.5000") 12.70 mm (.472 ‐ .512") 12.0‐13.0 mm 18,95€

PCPG‐42‐KIT TIR < 0.01 mm 1/4" 1/2" kit kit 66,45€

PCPG‐84‐KIT TIR < 0.01 mm 1/8" 1/4" kit kit 66,45€

PCPG‐842‐KIT TIR < 0.01 mm 1/8" 1/4" 1/2" kit kit 83,55€

PCSG‐1270‐1/2 TIR < 0.015 mm 1/2" (.5000") 12.70 mm (.472 ‐ .512") 12.0‐13.0 mm 14,20€


Precision PC Nuts for Porter-Cable Routers


Collet N

uts

Used in applications where speeds exceed 10,000 PRM

H.R.C. 45-52 Balanced to 24,000 RPM @ G2.5

TIR (with PC collet) < 0.005 mm (0.0002") must be used with InGraph PCPG nuts and

spanner


Improved collet centering and tool shank clamping

Low noise operation Longer tool life More accurate cutting and higher kerf fidelity

Compatible with carbide microtools Low TIR means less wear and tear on spindle

bearings

Applications: compatible with Porter-Cable:

690, 690LR, 9690LR, 691, 693, 890, 891, 892, 893, 7518, 7519, 7536, 7537, 7538, 7539 routers

Item# Description TIR Net Price*

PCPG‐0429‐NUT Collet nut for Porter‐Cable collets TIR < 0.005 mm 18,95 €

PCPG‐0429‐SPN Spanner wrench (for PCPG‐0429‐NUT collet nut) ‐ 10,40 €



Precision Spring Collets for Bosch 1618 and Hitachi Routers

1618 Collets

Specifications: Benefits: Steel - SUJ 2


SG (standard grade) TIR < 0.015 mm (0.0006") PG (precision grade) TIR < 0.01 mm (0.0004") UP (ultra-precision grade) TIR < 0.005 mm

(0.0002") Degree of concentricity exceeds the DIN

standard. 100% examined

must be used with InGraph BOPG-1618 nuts and spanner


Low noise operation



Applications: compatible with Bosch 1617, 1618 & 1619 routers and

Hitachi M12VC &KM12VC routers


BOPG‐0318‐1/8 TIR < 0.01 mm 1/8" (.1250") 3.18 mm (.118 ‐ .157") 3.0‐4.0 mm 18,95€

BOPG‐0635‐1/4 TIR < 0.01 mm 1/4" (.2500") 6.35 mm (.236 ‐ .276") 6.0‐7.0 mm 18,95€

BOPG‐0800‐5/16 TIR < 0.01 mm 5/16"(.3125") 8.00 mm ‐ 18,95€

BOPG‐1270‐1/2 TIR < 0.01 mm 1/2" (.5000") 12.70 mm (.472 ‐ .512") 12.0‐13.0 mm 18,95€

BOPG‐42‐KIT TIR < 0.01 mm 1/4" 1/2" kit kit 66,45€

BOPG‐84‐KIT TIR < 0.01 mm 1/8" 1/4" kit kit 66,45€

BOPG‐842‐KIT TIR < 0.01 mm 1/8" 1/4" 1/2" kit kit 83,55€

BOSG‐1270‐1/2 TIR < 0.015 mm 1/2" (.5000") 12.70 mm (.472 ‐ .512") 12.0‐13.0 mm 14,20€


Precision Collet Nuts for Bosch 1618 and Hitachi Routers

Collet Nuts

Specifications: Benefits: Used in applications where speeds exceed

10,000 PRM

H.R.C. 45-52 Balanced to 24,000 RPM @ G2.5 TIR (with PC collet) < 0.005 mm (0.0002")

must be used with InGraph BOPG nuts and spanner


Improved collet centering and tool shank clamping Low noise operation



Applications: compatible with Bosch 1617, 1618 & 1619 routers

and Hitachi M12VC &KM12VC routers


BOPG‐1618‐NUT Collet nut for Bosch 1618 TIR < 0.005 mm 18,95 €

BOPG‐1618‐SPN Spanner wrench (for BOPG‐1618‐NUT collet nut) ‐ 10,40 €



Precision Spring Collets for Bosch Colt Palm Routers and Rigid


Bosch

Collets

Steel - SUJ 2


SG (standard grade) TIR < 0.015 mm (0.0006") PG (precision grade) TIR < 0.01 mm (0.0004") Degree of concentricity exceeds the DIN standard.

100% examined must be used with InGraph BCPG-COLT nuts and

spanners


Low noise operation



Applications: compatible with Bosch Colt PR20EVSNK and

Rigid R2400 laminate trimmers


BCPG‐0318‐1/8 TIR < 0.01 mm 1/8" (.1250") 3.18 mm (.118 ‐ .157") 3.0‐4.0 mm 18,95€

BCPG‐0635‐1/4 TIR < 0.01 mm 1/4" (.2500") 6.35 mm (.236 ‐ .276") 6.0‐7.0 mm 18,95€

BCPG‐84‐KIT TIR < 0.01 mm 1/8" 1/4" kit kit 66,45€

BCSG‐1270‐1/4 TIR < 0.015 mm 1/4" (.2500") 6.35 mm (.236 ‐ .276") 6.0‐7.0 mm 14,20€


Precision PC Nuts for Bosch Colt Palm Routers and Rigid


Collet N

uts

Used in applications where speeds exceed 10,000 PRM

H.R.C. 45-52 Balanced to 24,000 RPM @ G2.5 TIR (with PC collet) < 0.005 mm (0.0002")

must be used with InGraph BCPG-COLT nuts and spanner


Improved collet centering and tool shank clamping Low noise operation



Applications: compatible with Bosch Colt PR20EVSNK and Rigid

R2400 laminate trimmers


BCPG‐COLT‐NUT Collet nut for Bosch Colt collets TIR < 0.005 mm 18,95 €

BCPG‐COLT‐SPN Spanner wrench (for BCPG‐COLT‐NUT collet nut) ‐ 10,40 €


FrezyCNC.eu FrezyCNC.pl CNCtools.eu A1 | P a g e

Carbide Drill Bit Feeds and Speeds for W208 series Drill Bits (for Double-sided Copperclad FR-4)

This feeds and speeds table was compiled using premium grade double-sided 1-ounce (37micron) copperclad with a 1.50 mm (0.059") thick FR-4 core.

Drilling Parameters for W208 series Drill Bits

Diameter

Feed

‐

Rate

Speed

Retract

Z‐Axis‐

Offset

Chipload

SFM

Diameter

Feed

‐

Rate

Speed

Retract

Z‐Axis‐

Offset

Chipload

SFM

(mm) (inch) (mm/ min)

(RPM) (m/ min)

(mm) (mils/ rev)

(mm) (inch) (mm/ min)

(RPM) (m/ min)

(mm) (mils/ rev)

0.10 0.0040 0.51 80.000 5 ‐0.0279 0.25 84 3.30 0.1299 1.52 20.000 25 ‐0.0483 3.00 680

0.13 0.0050 0.58 80.000 8 ‐0.0279 0.29 105 3.35 0.1319 1.52 20.000 25 ‐0.0483 3.00 690

0.15 0.0059 0.69 80.000 8 ‐0.0279 0.34 124 3.40 0.1339 1.52 20.000 25 ‐0.0483 3.00 701

0.25 0.0098 1.52 80.000 20 ‐0.0305 0.75 205 3.45 0.1358 1.52 20.000 25 ‐0.0483 3.00 711

0.30 0.0118 1.85 80.000 25 ‐0.0330 0.91 247 3.50 0.1378 1.52 20.000 25 ‐0.0483 3.00 721

0.35 0.0138 2.21 80.000 25 ‐0.0330 1.09 289 3.55 0.1398 1.52 20.000 25 ‐0.0483 3.00 732

0.40 0.0158 2.41 80.000 25 ‐0.0356 1.19 331 3.60 0.1417 1.52 20.000 25 ‐0.0483 3.00 742

0.45 0.0177 2.54 80.000 25 ‐0.0356 1.25 371 3.65 0.1437 1.52 20.000 25 ‐0.0508 3.00 752

0.50 0.0197 2.77 80.000 25 ‐0.0381 1.36 412 3.70 0.1457 1.52 20.000 25 ‐0.0508 3.00 762

0.55 0.0217 3.25 80.000 25 ‐0.0381 1.60 454 3.75 0.1476 1.52 20.000 25 ‐0.0508 3.00 772

0.60 0.0236 3.76 80.000 25 ‐0.0406 1.85 494 3.80 0.1496 1.52 20.000 25 ‐0.0508 3.00 783

0.65 0.0256 4.39 80.000 25 ‐0.0406 2.16 536 3.85 0.1516 1.52 20.000 25 ‐0.0508 3.00 793

0.70 0.0276 4.90 80.000 25 ‐0.0406 2.41 578 3.90 0.1535 1.52 20.000 25 ‐0.0508 3.00 803

0.75 0.0295 5.23 78.000 25 ‐0.0432 2.64 600 3.95 0.1555 1.52 20.000 25 ‐0.0508 3.00 814

0.80 0.0315 5.46 73.000 25 ‐0.0432 2.95 600 4.00 0.1575 1.52 20.000 25 ‐0.0508 3.00 824

0.85 0.0335 5.18 68.000 25 ‐0.0457 3.00 600 4.05 0.1594 1.40 20.000 25 ‐0.0533 2.75 834

0.90 0.0354 4.95 65.000 25 ‐0.0457 3.00 600 4.10 0.1614 1.40 20.000 25 ‐0.0533 2.75 845

0.95 0.0374 4.65 61.000 25 ‐0.0483 3.00 600 4.15 0.1634 1.40 20.000 25 ‐0.0533 2.75 855

1.00 0.0394 4.42 58.000 25 ‐0.0483 3.00 600 4.20 0.1654 1.40 20.000 25 ‐0.0533 2.75 866

1.05 0.0413 4.27 56.000 25 ‐0.0508 3.00 600 4.25 0.1673 1.40 20.000 25 ‐0.0533 2.75 876

1.10 0.0433 4.04 53.000 25 ‐0.0508 3.00 600 4.30 0.1693 1.40 20.000 25 ‐0.0533 2.75 886

1.15 0.0453 3.89 51.000 25 ‐0.0533 3.00 600 4.35 0.1713 1.40 20.000 25 ‐0.0533 2.75 896

1.20 0.0472 3.73 49.000 25 ‐0.0533 3.00 600 4.40 0.1732 1.40 20.000 25 ‐0.0533 2.75 906

1.25 0.0492 3.58 47.000 25 ‐0.0533 3.00 600 4.45 0.1752 1.40 20.000 25 ‐0.0559 2.75 917

1.30 0.0512 3.43 45.000 25 ‐0.0559 3.00 600 4.50 0.1772 1.40 20.000 25 ‐0.0559 2.75 927

1.35 0.0531 3.28 43.000 25 ‐0.0559 3.00 600 4.55 0.1792 1.27 20.000 25 ‐0.0559 2.50 938

1.40 0.0551 3.20 42.000 25 ‐0.0584 3.00 600 4.60 0.1811 1.27 20.000 25 ‐0.0559 2.50 948

1.45 0.0571 3.05 40.000 25 ‐0.0584 3.00 600 4.65 0.1831 1.27 20.000 25 ‐0.0559 2.50 958

1.50 0.0591 2.97 39.000 25 ‐0.0610 3.00 600 4.70 0.1850 1.27 20.000 25 ‐0.0559 2.50 968

1.55 0.0610 2.90 38.000 25 ‐0.0610 3.00 600 4.75 0.1870 1.27 20.000 25 ‐0.0559 2.50 979

1.60 0.0630 2.74 36.000 25 ‐0.0635 3.00 600 4.80 0.1890 1.14 20.000 25 ‐0.0584 2.25 989

1.65 0.0650 2.67 35.000 25 ‐0.0635 3.00 600 4.85 0.1909 1.14 20.000 25 ‐0.0584 2.25 999

1.70 0.0669 2.59 34.000 25 ‐0.0660 3.00 600 4.90 0.1929 1.14 20.000 25 ‐0.0584 2.25 1010

1.75 0.0689 2.51 33.000 25 ‐0.0660 3.00 600 4.95 0.1949 1.14 20.000 25 ‐0.0584 2.25 1020

1.80 0.0709 2.44 32.000 25 ‐0.0686 3.00 600 5.00 0.1968 1.14 20.000 25 ‐0.0584 2.25 1030

1.85 0.0728 2.36 31.000 25 ‐0.0686 3.00 600 5.05 0.1988 1.14 20.000 25 ‐0.0584 2.25 1040

1.90 0.0748 2.36 31.000 25 ‐0.0686 3.00 600 5.10 0.2008 1.02 20.000 25 ‐0.0584 2.00 1051

1.95 0.0768 2.29 30.000 25 ‐0.0711 3.00 600 5.15 0.2028 1.02 20.000 25 ‐0.0584 2.00 1061

2.00 0.0787 2.21 29.000 25 ‐0.0711 3.00 600 5.20 0.2047 1.02 20.000 25 ‐0.0610 2.00 1071

2.05 0.0807 2.13 28.000 25 ‐0.0737 3.00 600 5.25 0.2067 1.02 20.000 25 ‐0.0610 2.00 1082

2.10 0.0827 2.13 28.000 25 ‐0.0737 3.00 600 5.30 0.2087 1.02 20.000 25 ‐0.0610 2.00 1092

2.15 0.0846 2.06 27.000 25 ‐0.0762 3.00 600 5.35 0.2106 1.02 20.000 25 ‐0.0610 2.00 1102

2.20 0.0866 1.98 26.000 25 ‐0.0762 3.00 600 5.40 0.2126 1.02 20.000 25 ‐0.0610 2.00 1113

2.25 0.0886 1.98 26.000 25 ‐0.0787 3.00 600 5.45 0.2146 1.02 20.000 25 ‐0.0610 2.00 1123

2.30 0.0906 1.91 25.000 25 ‐0.0787 3.00 600 5.50 0.2165 1.02 20.000 25 ‐0.0610 2.00 1133

2.35 0.0925 1.91 25.000 25 ‐0.0813 3.00 600 5.55 0.2185 1.02 20.000 25 ‐0.0610 2.00 1143

2.40 0.0945 1.83 24.000 25 ‐0.0813 3.00 600 5.60 0.2205 1.02 20.000 25 ‐0.0635 2.00 1154

2.45 0.0965 1.83 24.000 25 ‐0.0838 3.00 600 5.65 0.2224 0.89 20.000 25 ‐0.0635 1.75 1164

2.50 0.0984 1.75 23.000 25 ‐0.0838 3.00 600 5.70 0.2244 0.89 20.000 25 ‐0.0635 1.75 1174

2.55 0.1004 1.75 23.000 25 ‐0.0838 3.00 600 5.75 0.2264 0.89 20.000 25 ‐0.0635 1.75 1185

2.60 0.1024 1.68 22.000 25 ‐0.0864 3.00 600 5.80 0.2283 0.89 20.000 25 ‐0.0635 1.75 1195

2.65 0.1043 1.68 22.000 25 ‐0.0864 3.00 600 5.85 0.2302 0.89 20.000 25 ‐0.0635 1.75 1205

2.70 0.1063 1.68 22.000 25 ‐0.0889 3.00 600 5.90 0.2323 0.89 20.000 25 ‐0.0635 1.75 1216

2.75 0.1083 1.60 21.000 25 ‐0.0889 3.00 600 5.95 0.2343 0.89 20.000 25 ‐0.0660 1.75 1226

2.80 0.1102 1.60 21.000 25 ‐0.0914 3.00 600 6.00 0.2362 0.89 20.000 25 ‐0.0660 1.75 1236

2.85 0.1122 1.52 20.000 25 ‐0.0914 3.00 600 6.05 0.2382 0.89 20.000 25 ‐0.0660 1.75 1247

2.90 0.1142 1.52 20.000 25 ‐0.0940 3.00 600 6.10 0.2402 0.76 20.000 25 ‐0.0660 1.50 1257

2.95 0.1161 1.52 20.000 25 ‐0.0940 3.00 608 6.15 0.2421 0.76 20.000 25 ‐0.0660 1.50 1267

3.00 0.1181 1.52 20.000 25 ‐0.0965 3.00 618 6.20 0.2441 0.76 20.000 25 ‐0.0660 1.50 1277

3.05 0.1201 1.52 20.000 25 ‐0.0965 3.00 629 6.25 0.2461 0.76 20.000 25 ‐0.0660 1.50 1288

3.10 0.1220 1.52 20.000 25 ‐0.0965 3.00 638 6.30 0.2480 0.76 20.000 25 ‐0.0660 1.50 1298

3.15 0.1240 1.52 20.000 25 ‐0.0991 3.00 649 6.35 0.2500 0.76 20.000 25 ‐0.0686 1.50 1308

3.20 0.1260 1.52 20.000 25 ‐0.0457 3.00 659 6.40 0.2520 0.76 20.000 25 ‐0.0686 1.50 1319

3.25 0.1280 1.52 20.000 25 ‐0.0457 3.00 670 6.50 0.2559 0.76 20.000 25 ‐0.0686 1.50 1339


Carbide Drill Bit Feeds and Speeds for W208 series Drill Bits (for a various materials)

Drilling Parameters for W30S208 and W30U208 series Drill Bits

Materials: CEM 3, FR3, SS‐FR4, DS‐

FR4 DS‐FR4, ML

ML, ML>8 High‐TG, BT resins, Polyimid, Filled

materials

BT resins, Polyimid, Teflon, Nonferrous

metals, Filled materials

Table‐Feed‐Rate: 175 m/min 150 m/min 125 m/min 100 m/min

Diameter

Speed

Chipload

Plunge‐

Feed

‐Rate

Speed

Chipload

Plunge‐

Feed

‐Rate

Speed

Chipload

Plunge‐

Feed

‐Rate

Speed

Chipload

Plunge‐

Feed

‐Rate

Retract

(mm) (RPM) (mils/ rev)

(m/ min)

(RPM) (mils/ rev)

(m/ min)

(RPM) (mils/ rev)

(m/ min)

(RPM) (mils/ rev)

(m/ min)

(m/ min)

0.10 180.000 0.007 1.2 180.000 0.006 1.1 180.000 0.006 1.0 180.000 0.005 0.9 3.3

0.125 180.000 0.008 1.5 180.000 0.008 1.4 180.000 0.007 1.2 180.000 0.006 1.1 4.2

0.15 180.000 0.010 1.8 180.000 0.009 1.6 180.000 0.008 1.5 180.000 0.008 1.4 5.1

0.175 180.000 0.011 2.0 180.000 0.011 1.9 180.000 0.010 1.7 180.000 0.009 1.6 6.0

0.20 180.000 0.013 2.3 180.000 0.012 2.2 180.000 0.011 2.0 160.000 0.010 1.6 6.9

0.225 180.000 0.015 2.6 180.000 0.014 2.4 177.000 0.012 2.2 142.000 0.011 1.6 7.8

0.25 180.000 0.016 2.9 180.000 0.015 2.7 160.000 0.014 2.2 128.000 0.013 1.6 8.8

0.275 180.000 0.018 3.2 174.000 0.017 2.9 145.000 0.015 2.2 116.000 0.014 1.6 9.4

0.30 180.000 0.020 3.5 160.000 0.018 2.9 133.000 0.017 2.2 107.000 0.015 1.6 9.5

0.35 160.000 0.023 3.6 137.000 0.021 2.9 114.000 0.019 2.2 91.000 0.018 1.6 9.6

0.40 140.000 0.026 3.6 120.000 0.024 2.9 100.000 0.022 2.2 80.000 0.020 1.6 9.8

0.45 124.000 0.029 3.6 107.000 0.027 2.9 89.000 0.025 2.2 71.000 0.023 1.6 10.0

0.50 112.000 0.033 3.6 96.000 0.030 2.9 80.000 0.028 2.2 64.000 0.025 1.6 10.1

0.55 102.000 0.036 3.6 87.000 0.033 2.9 73.000 0.030 2.2 58.000 0.028 1.6 10.2

0.60 93.000 0.039 3.6 80.000 0.036 2.9 67.000 0.033 2.2 54.000 0.030 1.6 10.4

0.65 86.000 0.042 3.6 74.000 0.039 2.9 62.000 0.036 2.2 49.000 0.033 1.6 10.5

0.70 80.000 0.046 3.6 69.000 0.042 2.9 57.000 0.039 2.2 46.000 0.035 1.6 10.7

0.75 75.000 0.049 3.7 64.000 0.045 2.9 54.000 0.041 2.2 43.000 0.038 1.6 10.8

0.80 70.000 0.052 3.6 60.000 0.048 2.9 50.000 0.044 2.2 40.000 0.040 1.6 10.9

0.85 66.000 0.055 3.6 57.000 0.051 2.9 47.000 0.047 2.2 38.000 0.043 1.6 11.2

0.90 62.000 0.059 3.6 54.000 0.054 2.9 45.000 0.050 2.2 36.000 0.045 1.6 11.4

0.95 59.000 0.062 3.6 51.000 0.057 2.9 42.000 0.052 2.2 34.000 0.048 1.6 11.5

1.00 56.000 0.065 3.6 48.000 0.060 2.9 40.000 0.055 2.2 32.000 0.050 1.6 max.

1.10 51.000 0.072 3.6 44.000 0.066 2.9 37.000 0.061 2.2 29.000 0.055 1.6 max.

1.20 47.000 0.078 3.7 40.000 0.072 2.9 34.000 0.066 2.2 27.000 0.060 1.6 max.

1.30 43.000 0.080 3.4 37.000 0.078 2.8 31.000 0.072 2.2 25.000 0.065 1.6 max.

1.40 40.000 0.080 3.2 35.000 0.080 2.6 29.000 0.075 2.2 23.000 0.070 1.6 max.

1.50 38.000 0.080 3.0 32.000 0.080 1.9 27.000 0.075 2.0 22.000 0.070 1.5 max.

2.00 28.000 0.080 2.2 24.000 0.080 1.6 20.000 0.075 1.5 20.000 0.070 1.4 max.

2.50 23.000 0.080 1.8 20.000 0.080 1.6 20.000 0.075 1.5 20.000 0.070 1.4 max.

3.00 20.000 0.080 1.6 20.000 0.080 1.6 20.000 0.075 1.5 20.000 0.070 1.4 max.

4.00 20.000 0.080 1.6 20.000 0.080 1.6 20.000 0.075 1.5 20.000 0.070 1.4 max.

5.00 20.000 0.080 1.6 20.000 0.080 1.6 20.000 0.075 1.5 20.000 0.070 1.4 max.

6.00 20.000 0.080 1.6 20.000 0.080 1.6 20.000 0.075 1.5 20.000 0.070 1.4 max.

6.50 20.000 0.080 1.6 20.000 0.080 1.6 20.000 0.075 1.5 20.000 0.070 1.4 max.


Carbide Drill Bit Feeds and Speeds for WS30S208 series Drill Bits (for Double-sided Copperclad FR-4)

Drilling Parameters for WS30S208 series Slot Drills In feed slot length >= 2 x d In feed slot length < 2 x d

Diameter Speed Chipload Table‐Feed‐Rate Chipload Table‐Feed‐Rate

(mm) (RPM) (mils/rev) (m/min) (mils/rev) (m/min)

min. max. min. max. min. max.

0.50/0.55 82.800 108.200 0.030 2,5 3,3 0.015 1,3 1,7

0.60/0.65 69.000 90.200 0.036 2,5 3,3 0.018 1,3 1,7

0.70/0.75 59.100 77.300 0.042 2,5 3,3 0.021 1,3 1,7

0.80/0.85 51.700 67.600 0.048 2,5 3,3 0.024 1,3 1,7

0.90/0.05 46.000 60.100 0.054 2,5 3,3 0.027 1,3 1,7

1.00/1.05 41.400 54.100 0.060 2,5 3,3 0.030 1,3 1,7

1.10/1.15 37.600 49.200 0.066 2,5 3,3 0.033 1,3 1,7

1.20/1.25 34.500 45.100 0.072 2,5 3,3 0.036 1,3 1,7

1.30/1.35 31.800 41.600 0.078 2,5 3,3 0.039 1,3 1,7

1.40/1.45 29.600 38.700 0.080 2,4 3,1 0.040 1,2 1,6

1.50/1.55 27.600 36.100 0.080 2,3 2,9 0.040 1,2 1,5

1.60/1.65 25.900 33.800 0.080 2,1 2,8 0.040 1,1 1,4

1.70/1.75 24.300 31.800 0.080 2,0 2,6 0.040 1,0 1,3

1.80/1.85 23.000 30.100 0.080 1,9 2,5 0.040 1,0 1,3

1.90/1.05 21.800 28.500 0.080 1,8 2,3 0.040 0,9 1,2

2.00/2.05 20.700 27.100 0.080 1,7 2,2 0.040 0,9 1,1


Carbide Router Bit Feeds and Speeds for SC208 and SD208 series Router Bits (for Double-sided Copperclad FR-4)

This feeds and speeds table was compiled routing premium grade double-sided 1-ounce (37micron) copperclad with a 1.50 mm (0.059") thick FR-4 core.

Routing Parameters for SC208 and SD208 series router bits

Diameter Table‐Feed‐Rate Speed Plunge‐Feed‐Rate Z‐Axis‐Offset

(mm) (inch) (m/min) (RPM) (m/min) (mm)

0.80 0.0315 0.4 60.000 20 ‐0.508

0.90 0.0354 0.4 55.000 20 ‐0.508

1.00 0.0394 0.5 55.000 20 ‐0.508

1.10 0.0433 0.6 50.000 25 ‐0.508

1.20 0.0472 0.8 47.000 25 ‐0.635

1.30 0.0512 0.9 45.000 25 ‐0.635

1.40 0.0551 0.9 40.000 25 ‐0.635

1.50 0.0591 0.9 38.000 25 ‐0.762

1.60 0.063 1.0 36.000 25 ‐0.762

1.70 0.0669 1.0 34.000 25 ‐0.762

1.80 0.0709 1.0 34.000 25 ‐0.889

1.90 0.0748 1.0 30.000 25 ‐0.889

2.00 0.0787 1.0 27.000 25 ‐0.889

2.10 0.0827 1.0 27.000 25 ‐1.016

2.20 0.0866 1.0 25.000 25 ‐1.016

2.30 0.0906 1.0 25.000 25 ‐1.016

2.40 0.0945 1.0 24.000 25 ‐1.143

2.50 0.0984 1.0 22.000 25 ‐1.27

3.00 0.1181 1.0 20.000 25 ‐1.397

3.10 0.122 1.0 20.000 25 ‐1.524

3.18 0.125 1.0 20.000 25 ‐1.524


Carbide Router Bit Feeds and Speeds for MSC208 and MSD208 series Router Bits (for a various materials)

Routing Parameters for MSC208 and MSD208 series routers

Materials: High speed routing FR4, FR4‐ML FR4, FR4‐ML, Polyimid, High‐Tg‐FR4, BT resins,

Filled materials

Nonferrous metals, Prepregs, Teflon, Aramid, Polyimid, High‐Tg‐FR4, BT resins, Filled materials

Table‐Feed‐Rate: 250 m/min 180 m/min 150 m/min 100 m/min

Diameter Speed Plunge‐Feed‐

Rate Speed

Plunge‐Feed‐Rate

Speed Plunge‐Feed‐

Rate Speed

Plunge‐Feed‐Rate

(mm) (RPM) (m/min) (RPM) (m/min) (RPM) (m/min) (RPM) (m/min)

0,30 100,000 0,5 100.000 0,5 100.000 0,5 100.000 0,5

0,40 100.000 0,7 100.000 0,7 100.000 0,7 79.700 0,6

0,50 100.000 0,9 100.000 0,9 95.600 0,9 63.700 0,6

0,60 100.000 1,1 95.600 1,1 79.700 0,9 53.100 0,6

0,70 100.000 1,3 81.900 1,2 68.300 0,9 45.500 0,6

0,80 99.600 1,5 71.700 1,2 59.800 0,9 39.900 0,6

0,90 88.500 1,5 63.700 1,2 53.100 0,9 35.400 0,6

1,00 79.700 1,5 57.400 1,2 47.800 0,9 31.900 0,6

1,10 72.400 1,5 52.200 1,2 43.500 0,9 29.000 0,6

1 20 66.400 1,5 47.800 1,2 39.900 0,9 26.600 0,6

1,30 61.300 1,6 44.100 1,2 36.800 0,9 24.500 0,6

1,40 56.900 1,6 41.000 1,3 34.200 0,9 22.800 0,6

1,50 53.100 1,6 38.300 1,3 31.900 1,0 21.300 0,6

1,60 49.800 1,6 35.900 1,3 29.900 1,0 20.000 0,7

1,70 46.900 1,7 33.800 1,3 28.200 1,0 20.000 0,7

1,80 44.300 1,7 31.900 1,3 26.600 1,0 20.000 0,8

1,90 42.000 1,7 30.200 1,4 25.200 1,0 20.000 0,9

2,00 39.900 1,7 28.700 1,4 23.900 1,0 20.000 0,9

2,10 38.000 1,8 27.300 1,4 22.800 1,1 20.000 1,0

2,20 36.200 1,8 26.100 1,4 21.800 1,1 20.000 1,1

2,30 34.700 1,8 25.000 1,5 20.800 1,1 20.000 1,1

2,40 33.200 1,8 23.900 1 5 20.000 1,1 20.000 1,1

2,50 31.900 1,9 23.000 1,5 20.000 1,2 20.000 1,1

2,60 30.700 1,9 22.100 1,5 20.000 1,2 20.000 1,1

2,70 29.500 1,9 21.300 1,5 20.000 1,3 20.000 1,1

2,80 28.500 2,0 20.500 1,6 20.000 1 4 20.000 1,1

2,90 27.500 2,0 20.000 1,6 20.000 1,4 20.000 1,1

3,00 26.600 2,0 20.000 1,6 20.000 1,5 20.000 1,1


Carbide Engraver Bit Feeds and Speeds for G1G8 series Engraving Bits (for a various materials)

Engraving Parameters for G1G8 series engravers

Type Speed Plunge-Feed-Rate

(RPM) (m/min)

22,5 80.000 1,0-1,5

30 60.000 1,5-2,5

45 50.000 2,5-3,5

60 40.000 3,0-4,5

90 30.000 5,0-6,0

FrezyCNC.eu FrezyCNC.pl CNCtools.eu

PPRREECCIISSIIOONN SSOOLLIIDD CCAARRBBIIDDEE MMIICCRROOTTOOOOLLSS

MMIIKKOOLLAAJJCCZZYYKKAA 3377 7722--110000 GGOOLLEENNIIOOWW PPOOLLAANNDD PPHHOONNEE:: ++4488 666688 001188 881122 EE--mmaaiill:: iinnffoo@@FFrreezzyyCCNNCC..eeuu

Distributor:

Documents

EN Solid Carbide Tools Catalog