Model #200400T

EASY ENTRY STEPASSEMBLY INSTRUCTIONS

• Can be used with Model #200700T (Smart Choice Ladder) to create the Easy Entry System

1004 Jaycox Road • Avon, Ohio 44011888-333-1134

ST E P BY ST E P AS S E M B LY I N ST R U C T I O N S , C o n t ’ d

OptionalSmart Light

Step 6 Handrail/Deck SupportsSecure each Upper Handrail (E1) to the Lower Handrail (E2) by using theHandrail Connector (J). Use a #8 x 1" screw to secure the connector tothe lower and upper handrail. To secure your Easy Step to your deck orpool top seat, be sure to position the Deck Connectors (H) around theupper handrails prior to inserting the handrails in the step sockets. Insertthe upper and lower handrail assembly into the sockets located on thetop step and third step from the top. Secure the handrails to the side riserswith eight (8) #14 x 1-1/4" screws (N). Screw holes are located on theoutside of the left and right risers.

Step 7 Tread ScrewsNotice the four screw locations on the surface of the second tread. Secureeach location with one #8 x 1” screw.

Step 8 Pool InstallationNote: Two (2) people are required for installation.A total weight of approximately 125 lbs., is required to keep the step frommoving once in place. With the assistance of another person, carefullyplace the step into the pool. Place the three Ballast Bags (M) or otherballast over the Ballast Tray (D) to hold the step into place. Again, withthe assistance of another person, walk back and position the step againstthe pool wall to prevent swim behind hazards.

Step 9 Deck Mount InstallationWith the step in position close to the pool wall, slide the Deck Connectors(H) into installation position on either the pool top seat or pool deck.Secure to the deck with two (2) #8 x 1” screws (N). Use a minimum oftwo screws per deck connector. Now secure each Deck Connector (H) toeach Upper Handrail (E1) by using a single #8 x 1” screw as shown.

Note: Before you begin the assemblyof your ladder/step please insure youhave all components and hardware.

Note: Contact our customer servicedepartment to request any missingor damaged parts or hardware at888-333-1134.

Shown withEasy Entry System#200800T(200700T/200400T)

REV 020111

SAFETY INSTRUCTIONS:• Install step per manufacturer’s instructions.• Locate Easy Entry Step on a solid base.• Easy Entry Step is designed for use by one person at a time.• This step is intended for use as a swimming pool entry/exit only.• Face the step when entering and exiting the pool.• No jumping, no diving from the step.• Do not swim through, behind or around the step.

Tools RequiredCordless Screwgun/Drill, 1/8” Drill Bit,Standard Phillips Bit, Safety Glasses

SAND NOT INCLUDED. FLAT BOTTOM POOLS ONLY.

E2

E1

H

L

Easy Entry Step Components QtyA1) Upper Step Tread 1A2) Lower Step Tread 1B1) Upper Left Side Riser 1B2) Lower Left Side Riser 1C1) Upper Right Side Riser 1C2) Lower Right Side Riser 1D) Ballast Tray 1E1) Upper Handrails 2E2) Lower Handrails 2F) Top Step Support Brace 1G) Mid Riser Brace 1H) Deck Connectors 2I) Riser Cross Braces 2J) Handrail Connectors 2K) Step Tread Connector 1

Hardware Kit (not shown) QtyM) Ballast Sand Bags 3N) #8 x 1” SS Screws 18O) #14 x 1-1/4” SS Screws 8P) #10 x 3/4” SS Screws 9

EASY ENTRY STEP ASSEMBLY INSTRUCTIONS

ST E P BY ST E P AS S E M B LY I N ST R U C T I O N S

Model #200400T

Step 1 Step Tread AssemblyPosition the Step Tread Connector (K) and theUpper Step Tread (A1) as shown. Be sure toposition the Step Tread Connector with thetapered side towards the top of the step asshown. Align all connectors and snap in place(see Fig. 1). Be sure all connectors are firmlysecure. Repeat this process with the LowerStep Tread (A2).

As indicated in Fig. 2, use nine (9) #10 x 3/4”SS screws to secure the Upper and Lower StepTreads to the Step Tread Connector. DO NOTOVERTIGHTEN!

Step 5 Cross BraceLocate the Cross Braces (I). Also, locate the screw head alignment indicatorson the back side of the left and right risers. These are the elevated ridgeson the back side of each riser. Position the screw in between the linesand secure the cross brace with four (4) #8 screws (N).

Continued on back page

D

G

K

J

I

A1

A2

E2

E1

F

H

Fig. 1 Fig. 2

C1

C2

B2

B1

Step 2 Right Riser AssemblyPosition the Step Tread Assembly on its side as shown. Align the “mushroomhead” snaps with holes on the Lower Right Side Riser (C2). Once all snapsand alignment holes are in position, firmly hold down the riser and strikewith a rubber mallet to secure the “mushroom heads” to the riser. Repeatthis process with the Upper Right Side Riser (C1).

C2

A2

Step 3 Left Riser AssemblyPosition the Step Tread Assembly on its side as shown. Align the “mushroomhead” snaps with holes on the Lower Left Side Riser (B2). Once all snapsand alignment holes are in position, firmly hold down the riser and strikewith a rubber mallet to secure the “mushroom heads” to the riser. Repeatthis process with the Upper Left Side Riser (B1).

Step 4 Step Braces / Ballast TrayLocate the Top Step Support Brace (F). Position the brace with the openside facing toward the front of the step. Be sure to position the brace sothe notch on each end will align and be flush with the top side of eachriser. Locate the Mid-Riser Support Brace (G). Position the brace with theopen side facing down. Snap down and secure the brace over the tabswhich are located in the middle back section of each riser. Securely snapin Ballast Tray (D) over riser tabs.D

G

F

A1

A2

A second person will be of assistance in holding the side risers in place as it is being secured to the step treads.

B2