DS(EN)-OTM2602 - opwill.comopwill.com/edit/uploadfile/20190111105309.pdf · frames with special test code, then analyse these frames at the receiver to test the network. Multi-Stream

www.opwillsolution.com

OPWILL TECHNOLOGIES (BEIJING) CO., LTD.

OTM2602 1G Packet Ethernet Test Module

OTM2602 1G Packet Ethernet Module is a compact

test solution for the installation and maintenance for

Metro/Carrier Ethernet and IP services. It supplies a

compact test solution for 1G packet Ethernet,

include ITU-T Y.1564 standard for SLA and OAM test

features.

This module is compatible with OTP6200v2 (OPWILL

Intelligent Network Test Platform).

1 Gbit/s data stream in maximum;

RFC2544 test includes throughput, latency, frame loss, and back-to-back;

IEEE802.3ah, IEEE802.1ag, ITU-T Y.1731 and ITU-T G.8113.1 OAM test;

RFC3393 packet jitter test;

Y.1564 test;

BERT and loopback test from layer 1 to layer 4;

Generate up to 8 traffic flows with different MAC address, VLAN tags, MPLS, IP address, TCP/UDP, payload, and bandwidth;

Service disruption test;

IPV6.


Www.opwillsolution.com OPTIMISE THE TEST AS YOUR WILL

Platform Briefs: OTP6200

Compact and lightweight designed;

Graphical user interface, easy to operate;

6.5 inches outdoor-enhanced LCD colour touch screen;

Ultra-high capacity field-exchangeable Li-ion battery pack extends testing time;

Powerful modular intelligent network test platform;

Dial, number keys, and function keys for flexible scrolling and selecting;

Remote control by PC using 10/100M Base-T port.



Key Feature:

10/100/1000M Base-T and 100/1000M

Base-X dual media test interfaces, and full-

duplex and half-duplex (exclude 1000M)for

all rates;

Perform throughput, latency, frame loss, and

back-to-back measurements per industry-

standard RFC2544;

Network configuration testing and

performance testing per standard ITU-T

Y.1564;

Generate up to 8 traffic flows with different

MAC address, VLAN tags, MPLS, IP address,

TCP/UDP, payload, and bandwidth;

RFC2544 and Y.1564 Bidirectional testing; IEEE802.3ah, IEEE802.1ag, ITU-T Y.1731, and

ITU-T G.8113.1 OAM support;

Traffic scan according with MAC, IP, VLAN,

MPLS Label, and so on;

Ethernet BER and loopback testing at layer 1,

layer 2, layer 3, and layer 4

VoIP jitter testing according with standard

RFC3393;

Smart loop mode for layer 1, layer 2, layer 3,

and layer 4;

IPv4 and IPv6 traffic generation; Service disruption test;

Pass through monitor testing; Supports IEEE 1588v2/PTP and SyncE;

Fully integrated solution for synchronised

packet networks; IEEE 1588v2/PTP analysis;

Master clock and slave clock emulation; Support all type PTP messages real time

statistics;

ESMC SSM generation, monitoring and

decoding.



Applications:

RFC2544 Test:

OTM2602 fully meets RFC2544 standard, supports Throughput; Latency; Frame loss; and Back-to-Back test in metro network, and can be able to generate a complete test report.

Throughput

Latency

Frame Loss Test

Back-to-back Test



BERT Test:

Ethernet BERT test adopts the similar principle of SDH BERT test. It is by transferring the Ethernet frames with special test code, then analyse these frames at the receiver to test the network.

Multi-Stream Test:

OTM2602 supports to generate multiple data streams to test the forward ability of these service in Ethernet network. In addition, multiple data streams can be set as different priority.

OAM Test:

OAM test supports IEEE 802.3ah, IEEE 802.1ag, ITU-T Y.1731, and ITU-T G.8113.1 OAM link and services protocol. It includes partner link detection, remote loopback, MIB retrieval, and link event notification. It also can check network connection, connection ring back; generate link trace messages, and analyse service level of OAM test application. ITU-T Y.1731 OAM message can practice frame loss performance verification. ITU-T G.8113.1 OAM message can verify the PTN network, and practice and the frame loss performance verification.



Y.1564 Test:

RFC2544 was the most popular standard for Ethernet test. However, it is specially designed for indoor network facilities test, not suitable for outdoor field test. Hence, ITU‐T Y.1564sam is particularly introduced for telecom operator to do Ethernet network service launch and fault diagnosis. Compared with RFC2544, it includes critical SLA standards such as packet jitter identification and QoS measurements, which could increase test speed promptly, save test time and resource, and optimises QoS.

Network Configuration Test

Network configuration test will conduct a test for every service to verify whether the service configuration is correct or not, and whether all specific KPI or SLA parameters have been satisfied.

Performance Test

When the configuration of every service has been checked, and verified successfully, OTM2602 will conduct a test for the quality of service simultaneously.



General Specifications: OTP6200 + OTM2602

GENERAL SPECIFICATIONS

User Interface

Screen 6.5 Inch TFT Touch Screen (640 x 480);

Other Interface

USB USB2.0, A type, 2;

USB2.0 Mini B type, 1;

Ethernet Ethernet 10/100, RJ45;

Audio 3.5mm Audio Interface;

Storage 8G;

Physical Specifications

Temperature Operating: -10°C to 50°C;

Storage:-40°C to 70°C;

Relative Humidity 0% to 95%(non-condensing);

Size(H×W×D) OTP6200: 319mm x 202mm x 105mm;

OTM2602:25mm x 97mm x 259mm;

Weight OTP6200: 2.8kg;

OTM2602:0.4kg;

Vibrancy 10Hz to 500Hz < 1.5g (on 3 main axes);

Mechanical Shock 6 sides, 8 edges < 760cm, according to GR-196-CORE;

EMC EN55022/CIPSR22;

EN61000-3-2;

EN55024;

Battery and Power Supply

Battery

Rechargeable Li-lon batteries;

Working time: 8 hours (typical for 1000M Ethernet test);

Working time: 12 hours (typical for 100M Ethernet test);

Charging time: 6 hours (typical: 25°C);

Power Source Input: 100-240VAC, 50-60Hz,2A;

Output: 19VDC, 4A.



Technical Specifications: OTM2602

TECHNICAL SPECIFICATIONS

Ethernet

Port Electrical interface: 2 ports, 10/100/1000M Base-T;

Optical interface: 2 ports,100/1000M Base-X; User selectable optical module: 850nm, 1310nm, 1550nm.

Ethernet Feature

Auto negotiation, full and half duplex, flow control;

Configuration Monitor/Generate, pass-through;

Encapsulation Ethernet type II, IEEE802.3 with 802.2, IEEE802.3 with SNAP;

Configuration, Monitoring, and Generation

Traffic Generation

Variable line rate traffic generation, up to full line rate;

Traffic generate on: continuous, burst, ramp, n-frame, n-burst, n-ramp;

Adjustable frame size: 38 bytes to 16000 bytes;

Frame size: constant, iMAX, random;

User-defined traffic mix of unicast and broadcast frames;

Fixed or increment MAC/IP identifier;

User programmable DSCP/TOS byte;

Configurable IP and Ethernet source and destination addresses (support IPv4 and IPv6 addressing);

User programmable TCP/UDP address;

Generate pause frames, respond to pause frames;

Answer incoming ARP, ping requests;

Stacked VLAN

Up to 3 user-settable VLAN tags;

Parameters per VLAN tag: Ethernet type II 0x8100(802.1Q), 0x88a8(802.1ad), 0x9100, 0x9200, or 0x9300;

User-defined VLAN ID, CFI, VLAN priority;

Multi stream Number of streams: up to 8 streams per port can be activated;

Error Injection FCS, IP check sum error, UDP/TCP check sum error, bit error;

Alarm generation

No link;

Result, Monitoring and Generation

Status

Link status, interface type, jabber detected, frames present, MPLS/VLAN, speed, full or half duplex, signal present, bit rate of incoming Ethernet signal, auto negotiation complete;

Link partner abilities: speed/duplex;

Indicators of utilisation, throughput, errored frames;

Signal level indication for optical Ethernet interfaces; Performance

Statistics Utilisation, throughput, frame rate;

Frame Statistics

Total frames, total testing frames, total not testing frames, Unicast/Multicast/Broadcast frames, number of pause frames;

Total VLAN frames;

Total MPLS frames;

Total errored framed, number of oversized, normal, and runt frame, number of FCS errored;



Result, Monitoring and Generation

Frame Distribution

Statistics Total valid/frames, <64, 64-127, 128-511, 512-1023, 1024-1518, >1518;

Multi stream Display information per steam: Frame loss count/rate, throughput, latency, packet jitter, frames and bytes received

and transmitted; Transmit Statistics

Total frames, Unicast/Multicast/Broadcast;

Filter Filter condition support: Source and destination MAC/IP, IPv6, VLAN ID and VLAN Priority, MPLS, IP TOS,

TCP/UDP source and destination port, Ethernet type and IP protocol;

BER Test and Service Disruption Test

BER Test

Generation and detection of test pattern, count of errors in received test pattern;

Pattern generation: layer 1 to layer 4;

Frame loss count and frame loss seconds;

BER measurement results are calculated for: Physical layer, link layer, network layer, data layer;

Test pattern: PRBS9, PRBS11, PRBS15, PRBS20, PRBS23, PRBS31, CRPRJ, JTPAT, SPAT, 32bits user defined;

Error Injection FCS, IP check sum error, UDP/TCP check sum error, BIT error;

Service Disruption Test

Service disruption test activated as part of BER test: Max/Avg service disruption test, resolution: 0.1us;

Number of service disruption;

Loopback and Pass Though

Loopback Test

Layer 1 to layer 4 loopback test;

Advanced loopback test: Packet loss setting: percentage, packet count, time;

Loopback drop enable: protocol loss, protocol pass, control, CRC error, IP/TCP/UDP error;

Pass Through Test

Pass through monitoring function between 2× 1GE electrical or 2×1GE optical ports;

Advanced pass through test;

Packet loss setting: percentage, packet count, time;

Pass through drop enable: protocol loss, protocol pass, control, CRC error, IP/TCP/UDP error;

RFC3393

Jitter Test G.711, G.723.1, G.729 and so on VoIP packet jitter test;

Jitter result: hits, min, max, current, average;

RFC2544

RFC2544 Test

Switch/Router test and single ended network test mode: Throughput, frame loss, latency, back-to-back;

End-to-End network test mode (2 units in local-remote setup): Throughput, frame loss, back-to-back;

Service Activation Test (Y.1564)

Service Activation Test

ITU-T Y.1564 service activation test: Up to 8 services per port;

Colour-aware and non-colour-aware in combinations;

Test modes: one-way (uni-or bi-directional, symmetrical, or asymmetrical), round-trip;

Verification against service acceptance criteria: information rate, frame transfer delay, frame delay variation, frame loss rate, availability;



Service Activation Test (Y.1564)

Service Configuration

Test

Subtest for: committed information rate, excess information rate, traffic policing;

Step duration: 1-60s (user define);

Number of steps: 1 to 4;

Result: pass/fail indication, IR (min/avg/max), FL (count/FLR), FTD, FDV (min/avg/max (during measurement));

Service Performance

Test

All services tested simultaneously at CIR;

Duration 15min, 2hours, 24 hours, or user defined;

Result: pass/fail indication, IR (min/avg/max), FL (count/FLR), FTD, FDV (min/avg/max (during measurement));

Remote Smart Loopback Test

Remote Smart Loopback

Use as local unit control another remote unit for RFC2544 and Y.1564 bi-directional testing;

Support layer 1 to layer 4 smart loopback test;

Advanced IP Tools

PING For connectivity and configuration check: Round trip time (RTT); Support IPv4, TTL, URL;

Trace Route Trace IP route over IP network: Information per hop: PING time, number of ping timeouts;

VCT Cable Test Use for CAT5 cable connectivity check: Status: pass/fail;

Fault location;

Channel;

Polarity; Pair Skew;

Flow Control Flow control time, us: Pause time: total, last, max, min; Pause frame count: TX, RX;

FTP Upload/ Download

Use for FTP server and client emulation: Support IPv4 and URL;

Username/password;

File upload/download;

Result: pass/fail indication, upload/download time display;

HTTP WEB access: Support IPv4 and URL; HTTP access pass/fail;

Advanced PING (Topology)

Advance/fast PING, PING segments of the IP one by one in one time: IP address range: start, end;

Send count;

Timeout (ms);

Status: pass/fail indication;

MPLS

Number of MPLS Header

Up to 3 MPLS header set by user;

Parameter per MPLS Header

User defined label, Exp and TLL fields in each MPLS header;

Statistics MPLS frame count;

OAM (MPLS-TP)

Complies ITU-T G.8113.1;

Support OAM messages: ITU-T Y.1731: CCM, LBM, LBR, LTM, LTR, AIS, LCK, LMM, LMR, 1DM, DMM, DMR;

IEEE802.1ag: CCM, LBM, LBR, LTM, LTR;

Ethernet OAM

OAM Standards ITU-T Y.1731 service layer OAM;

IEEE802.1ag connectivity layer OAM;

IEEE802.3 (formerly IEEE802.3ah) access link OAM;

Messages

Generate and receive following OAM messages: ITU-T Y.1731: CCM, LBM, LBR, LTM, LTR, AIS, LCK, LMM, LMR, 1DM, DMM, DMR;

IEEE802.1ag: CCM, LBM, LBR, LTM, LTR;

IEEE802.3ah: information, variable request, variable response, loopback control;



Ethernet OAM

IEEE802.3ah Function

Discovery;

Loopback activate;

Statistics Number of each message generated/received;

Synchronous Ethernet Test

SyncE

Specify quality level of transmitted Ethernet signal;

Analysis of QL indicated in received Ethernet signal with alarm at missing QL indications;

Result: SSM RX count and rate, SSM TX count, indicated QL statistics, SSF seconds;

ESMC message captured and exported in Wireshark format;

IEEE1588v2 PTP

Each port of Ethernet interface can be acted as master or slave independently;

Parameter configuration: Domain: 0 to 255;

Step mode: one-step, two-step;

Delay mechanism: delay request/response, peer delay;

Negotiation: ON/OFF (unicast only);

Clock source: Internal or UTC locked with GPS;

Clock Identify;

Priory #1 or #2, class, time source,

Accuracy index: 0 to 255;

Announce interval: 1/2 to 64;

Sync interval: 1/2 to 256;

Delay request interval: 1/16 to 64;

Protocol stack: Layer2: Ethernet, Ethernet/VLAN;

Layer3: none, IPv4;

Synchronous Ethernet Test

IEEE1588v2 PTP

PTP protocol analysis: Statistics of IEEE1588 message and message rate;

Logged IEEE1588 events: clock state transitions, state transition events, faults, changes in grand-master clock;

IEEE1588 message captured and exported in Wireshark format;

Ethernet Frame Capture

Capture Buffer Size

48Mbytes;

When capture buffer full: stop;

Capture Frame Slicing

Can capture frame length by user defined;

Capture Data CAP format for display in Wireshark.



OTP6200 + OTM2602 Ordering Information

OTP6200+OTM2602 STANDARD CONFIGURAIOTN

Module Description

OTP6200 Test platform, support SDH, OTN, Ethernet, Packet Ethernet, OTDR test modules;

OTM2602

Dual Gigabit Ethernet test module;

Dual 10/100/1000M Base-T electrical interfaces;

Dual 1000M Base-X optical interfaces;

Layer 1 to Layer 4 BERT test;

Up to 8 streams generation and analysis with MAC/VLAN/IP/TCP/UDP;

RFC2544 standard test with Throughput, Latency, Frame Loss and Back-to-Back;

Bi-directional RFC2544 test;

RFC3393 Jitter test for VoIP packets;

Layer 1 to Layer 4 loopback and smart loopback test;

Through mode for Ethernet network monitoring;

Enable to drop data packet under though mode and loopback mode;

Up to 1000M streams generation with 3 Layer VLAN;

Ping, Trace Route, FTP Download/Upload, and HTTP tools;

Ethernet service disruption test;

Packet capture and analysis to 1000M rate;

Cable test with CAT5 Length and fault measurement;

Enable to generate frame with random length;

Enable to generate data streams with increment MAC and IP;

Bi-directional test;

Layer 1 bandwidth statistics ;

Remote control by PC;

Accessories Code Accessories Description

16080010 LC/PC to LC/PC full-duplex single-mode fibre, 3 meter, one;

16060040 CAT5 cable, 3 meter, one;

14020090 1.25G 1310nm 15Km LC SFP optical modules, two;

05020050 SFP optical port dust proof cap - black - rubber, two;

05020060 RJ45 electrical port dust proof cap - black - rubber, two;

16060010 3 pins adapter cable, one;

43170020 OTP6200 100-240V input and 19V output AC/DC power adapter, one;

18080010 OTP6200 disc include user manual and OPWILL remote control software, one;

19070010 OTP6200 package, one;

18010010 Factory test report, one;

18010020 Calibration certificate, one;

18040011 One year warranty service.


Copyright © OPWILL Technologies (Beijing) Co., Ltd. 2011-2018. All Rights Reserved.

OPWILL TECHNOLOGIES (BEIJING) CO., LTD.

Add: Room 415, Digital Media Building, No.7 Shangdi Information Road, Haidian District, Beijing, PRC. 100085

Tel: +86(10)8277-1386/2866/3382

Fax: +86(10)8277-1782

Please visit our website for the further information: www. opwillsoultion.com

OTM2602 OPTIONAL CONFIGURATION

Optional Software

OPAP-8023ahAGeEth IEEE802.3ah standard access OAM test.

OPAP-Y1564AGeEth Y.1564 standard service configuration and performance test for SLA QoS with CIR/EIR/Traffic Dropped for GE;

OPAP-DPY1564AGeEth (Need to order OPAP-Y1564AGeEth

first) Bi-directional Y.1564 test;

OPAP-IPv6AGeEth IPv6 feature, the test interface can set IPv6 address and can generate stream with IPv6;

OPAP-ScanAGeEth Traffic scan according with destination MAC/IP, source MAC/IP, 3 Layer VLAN, 3 Layer MPLS in-service test;

OPAP-EautoAGeEth Advance auto-negotiation, can set the remote equipment auto-negotiation the speed and duplex as you want;

OAPA-EPINGAGeEth Advance/Fast PING, PING segments of the IP one by one in one time;

OPAP-3MPLSAGeEth Up to 1000M streams generation with 3 Layer MPLS label;

OPAP-DPRFC2544AGeEth Enhancement RFC2544 test, support different upstream and downstream rates setup for Throughput, Frame Loss and Back-to- Back test;

OPAP-Y1731AGeEth ITU-T Y.1731 standard Ethernet OAM test;

OPAP-G81131AGeEth ITU-T G.8113.1 standard MPLS-TP OAM test;

OPAP-FXAGeEth Dual 100M Base-X optical ports;

Optional Hardware

43160031 OTP6200 lithium polymer rechargeable battery;

OPAP-Onewarranty One year extended warranty service;

OPAP-Twowarranty Two years extended warranty service;

14020160 1.25G-850nm-550m-MM-LC-SFP-DDM;

14020090 1.25G-1310nm-15km-SM-LC-SFP-DDM;

14020340 1.25G-1550nm-40km-SM-LC-SFP-DDM.

Notes: Product ordering information may update along with the product upgrade, please refer to the final version provided by our sales.

Documents

DS(EN)-OTM2602 - opwill.comopwill.com/edit/uploadfile/20190111105309.pdf · frames with special test code, then analyse these frames at the receiver to test the network. Multi-Stream