DSC-T5 · 2013-07-25 · (including NP-FT1 battery pack and wrist strap, etc.) Microphone Electret condenser microphone Speaker Dynamic speaker Exif Print Compatible PRINT Image Matching

SERVICE MANUAL LEVEL 2

Link

DISASSEMBLY

SERVICE NOTE

SPECIFICATIONS

SCHEMATIC DIAGRAMS

FRAME SCHEMATIC DIAGRAMS

BLOCK DIAGRAMS

REPAIR PARTS LIST

PRINTED WIRING BOARDS

Link

Revision HistoryRevision History

How to useAcrobat Reader

How to useAcrobat Reader

Sony EMCS Co.DSC-T5_L2

Internal memoryON BOARD

Internal memoryON BOARD

Ver 1.2 2005.10

DIGITAL STILL CAMERA

DSC-T5

2005J0500-1 © 2005.10

Published by DI Technical Support Department9-876-887-31

US ModelCanadian Model

AEP ModelUK Model

E ModelAustralian Model

Hong Kong ModelChinese Model

Korea ModelBrazilian Model

Japanese ModelTourist Model

Photo: Silver

The components identified bymark 0 or dotted line withmark 0 are critical for safety.Replace only with part num-ber specified.

Les composants identifiés par unemarque 0 sont critiques pour lasécurité.Ne les remplacer que par une pièceportant le numéro spécifié.

• Precaution on Replacing the SY-134 Board

— 2 —DSC-T5_L2

SPECIFICATIONS

Camera[System]Image device 7.17 mm (1/2.5 type) color

CCD, Primary color filter

Total pixel number of cameraApprox. 5 255 000 pixels

Effective pixel number of cameraApprox. 5 090 000 pixels

Lens Carl Zeiss Vario-Tessar3× zoom lensf = 6.33 – 19.0 mm (38 – 114 mm when converted to a 35 mm still camera)F3.5 – 4.4

Exposure control Automatic exposure, Scene Selection (10 modes)

White balance Automatic, Daylight, Cloud y, Fluorescent, Incandescent, Flash

File format (DCF compliant)Still images: Exif Ver. 2.2JPEG compliant, DPOF compatibleMovies: MPEG1 com pliant (Monaural)

Recording media Internal Memory (32 MB)“Memory Stick Duo”

Flash Recommended distance (ISO set to Auto): approx. 0.1 m to 2.5 m (3 15/16 inches to 8 feet 2 7/16 inches) (W)/approx. 0.5 m to 2.0 m (1 feet 7 11/16 inches to 6 feet 6 3/4 inches) (T)

[Input and Outpu t connectors]Multi connector

USB communication

Hi-Speed USB (USB 2.0 compliant)

[LCD screen]LCD panel 6.2 cm (2.5 type) TFT drive

Total number of dots230 400 (960×240) dots

[Power, general]Power Rechargeable battery pack NP-

FT1, 3.6 V

AC-LS5K AC Adaptor (not supplied), 4.2 V

Power consumption (during shooting)1.1 W

Operating temperature0°C to +40°C (+32°F to +104°F)

Storage temperature–20°C to +60°C (–4°F to +140°F)

Dimens ions 93.6×60. 0×20.3 mm(3 3/4×2 3/8×13/16 inches)(W/H/D, excluding protrusions)

Mass Approx. 139 g (4.9 oz) (including NP-FT1 batte ry pac k and wrist strap, etc.)

Microphone Electret condenser microphone

Speaker Dynamic speaker

Exif Print Compatible

PRINT Image Matching IIICompatible

PictBridge Compatible

BC-CS3 battery chargerPower requirements

AC 100 to 240 V, 50/60 Hz, 3.2 W

Output v oltage DC 4.2 V, 500 mA

Operating temperature0°C to +40°C (+32°F to +104°F)

Storage temperature–20°C to +60°C (–4°F to +140°F)

Dimensions Approx. 66×23×91 mm(2 5/8×29/32×3 5/8 inches) (W/H/D)

Mass Approx. 70 g (2.7 oz)

Rechargeable battery pack NP-FT1Used battery Lithium-ion battery

Maximum voltageDC 4.2 V

Nominal voltage DC 3.6 V

Capacity 2.4 Wh (680 mAh)

Design and specifications are subject to change without notice.

— 3 —DSC-T5_L2

SAFETY-RELATED COMPONENT WARNING!!

COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE WITHMARK 0 ON THE SCHEMATIC DIAGRAMS AND IN THE PARTSLIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESECOMPONENTS WITH SONY PARTS WHOSE PART NUMBERSAPPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTSPUBLISHED BY SONY.

ATTENTION AU COMPOSANT AYANT RAPPORTÀ LA SÉCURITÉ!

LES COMPOSANTS IDENTIFÉS PAR UNE MARQUE 0 SUR LESDIAGRAMMES SCHÉMATIQUES ET LA LISTE DES PIÈCES SONTCRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT. NEREMPLACER CES COMPOSANTS QUE PAR DES PIÈSES SONYDONT LES NUMÉROS SONT DONNÉS DANS CE MANUEL OUDANS LES SUPPÉMENTS PUBLIÉS PAR SONY.

1. Check the area of your repair for unsoldered or poorly-solderedconnections. Check the entire board surface for solder splashesand bridges.

2. Check the interboard wiring to ensure that no wires are"pinched" or contact high-wattage resistors.

3. Look for unauthorized replacement parts, particularlytransistors, that were installed during a previous repair. Pointthem out to the customer and recommend their replacement.

4. Look for parts which, through functioning, show obvious signsof deterioration. Point them out to the customer andrecommend their replacement.

5. Check the B+ voltage to see it is at the values specified.6. FLEXIBLE Circuit Board Repairing

• Keep the temperature of the soldering iron around 270°Cduring repairing.

• Do not touch the soldering iron on the same conductor of thecircuit board (within 3 times).

• Be careful not to apply force on the conductor when solderingor unsoldering.

Unleaded solderBoards requiring use of unleaded solder are printed with the lead-free mark (LF) indicating the solder contains no lead.(Caution: Some printed circuit boards may not come printed withthe lead free mark due to their particular size.)

: LEAD FREE MARKUnleaded solder has the following characteristics.• Unleaded solder melts at a temperature about 40°C higher than

ordinary solder.Ordinary soldering irons can be used but the iron tip has to beapplied to the solder joint for a slightly longer time.Soldering irons using a temperature regulator should be set toabout 350°C.Caution: The printed pattern (copper foil) may peel away if theheated tip is applied for too long, so be careful!

• Strong viscosityUnleaded solder is more viscous (sticky, less prone to flow) thanordinary solder so use caution not to let solder bridges occur suchas on IC pins, etc.

• Usable with ordinary solderIt is best to use only unleaded solder but unleaded solder mayalso be added to ordinary solder.

SAFETY CHECK-OUT

After correcting the original service problem, perform the following

safety checks before releasing the set to the customer.

CAUTIONDanger of explosion if battery is incorrectly replaced.Replace only with the same or equivalent type.

— 4 —DSC-T5_L2

TABLE OF CONTENTS

1. SERVICE NOTE1-1. Description on Self-diagnosis Display ···························· 1-11-2. Process After Fixing Flash Error ····································· 1-11-3. Method for Copying or Erasing the Data in Internal

Memory ··········································································· 1-21-4. Precaution on Replacing the SY-134 Board ···················· 1-3

2. DISASSEMBLY2-1. Disassembly ····································································· 2-3

3. BLOCK DIAGRAMS3-1. Overall Block Diagram (1/2) ··········································· 3-13-2. Overall Block Diagram (2/2) ··········································· 3-33-3. Power Block Diagram ····················································· 3-5

4. PRINTED WIRING BOARDS ANDSCHEMATIC DIAGRAMS

4-1. Frame Schematic Diagram ·············································· 4-14-2. Schematic Diagrams ························································ 4-54-3. Printed Wiring Boards ··················································· 4-314-4. Waveforms ····································································· 4-454-5. Mounted Parts Location ················································ 4-48

5. REPAIR PARTS LIST5-1. Exploded Views ······························································· 5-25-2. Electrical Parts List ························································· 5-5

Section Title Page Section Title Page

1-1DSC-T5_L2

1. SERVICE NOTE

Self-diagnosis display• C: ss: ss

You can reverse the cameramalfunction yourself. (However,contact your Sony dealer or localauthorized Sony service facilitywhen you cannot recover from thecamera malfunction.)

• E: ss: ssContact your Sony dealer or localauthorized Sony service facility.

Display Code

C:32:ss

C:13:ss

Countermeasure

Turn the power off and on again.

Format the “Memory Stick” or internalmemory.

Cause

Trouble with hardware.

“Memory Stick” or internal memory isunformatted.

Caution Display During Error

SYSTEM ERROR

FORMAT ERROR

MEMORY STICK ERROR

E:61:ss

E:91:ss

1-1. DESCRIPTION ON SELF-DIAGNOSIS DISPLAY

Insert a new “Memory Stick”. “Memory Stick” is broken.

Turn the power off and on again. Trouble with internal memory. INTERNAL MEMORY ERROR

Checking of lens drive circuit. When failed in the focus and zoominitialization. —

Checking of flash unit or replacementof flash unit. (Note)

Abnormality when flash is beingcharged.

Note: After repair, be sure to perfom “1-2. PROCESS AFTER FIXING FLASH ERROR”.

1-2. PROCESS AFTER FIXING FLASH ERROR

When “FLASH error” (Self-diagnosis Code E : 91 : ** ) occurs, to prevent any abnormal situation caused by high voltage, setting of theflash is changed automatically to disabling charge and flash setting.After fixing, this setting needs to be deactivated. Flash error code can be initialized by the operations on the Setup screen.

Method for Initializing the Flash Error Code

Initializes the setting to the default setting.

1 Select [OK] with v on the control button, then press z.The message “Initialize all settings Ready?” appears.

2 Select [OK] with v, then press z.The settings are reset to the default setting.

• Make sure that the power is not disconnected during resetting.

Initialize

OK See the following procedure.

Cancel Cancels the resetting.

1-2DSC-T5_L2

1-3. METHOD FOR COPYING OR ERASING THE DATA IN INTERNAL MEMORY

The data can be copied/erased by the operations on the Setup screen. (When erasing the data, execute formatting the internal memory.)

Note: 1 When replacing the SY-134 board, erase the data in internal memory of the board before replacement.Note: 2 When replacing the SY-134 board or the IC401 on the SY-134 board, execute formatting and initialize the internal memory after

replacement.

Method for Copying the Data in Internal Memory

Method for Formatting the Internal Memory

Copies all images in the internal memory to a “Memory Stick Duo”.

1 Insert a “Memory Stick Duo” having 32 MB or larger capacity.2 Select [OK] with v on the control button, then press z.

The message “All data in internal memory will be copied Ready?” appears.

3 Select [OK] with v, then press z.Copying starts.

• Use a fully charged battery pack or the AC Adaptor (not supplied). If you attempt to copy image files using a battery pack with little remaining charge, the battery pack may run out, causing copying to fail or possibly corrupting the data.

• You cannot copy individual images.• The original images in the internal memory are retained even after copying. To delete the contents of the

internal memory, remove the “Memory Stick Duo” after copying, then execute the [Format] command in (Internal Memory Tool).

• You cannot select a folder copied on a “Memory Stick Duo”.• Even if you copy data, a (Print order) mark is not copied.

Copy


Cancel Cancels the copying.

Copying102_COPY

A

Formats the internal memory.• Note that formatting irrevocably erases all data in the internal memory, including even protected images.

1 Select [OK] with v on the control button, then press z.The message “All data in internal memory will be erased Ready?” appears.

2 Select [OK] with v, then press z.The format is complete.

Format


Cancel Cancels the formatting.

1-3EDSC-T5_L2

1-4. PRECAUTION ON REPLACING THE SY-134 BOARD

VIDEO OUT Default Data Check

When you replace to the repairing board, the written data of repairing board also might be changed to original setteing because of broadcastsystem (NTSC/PAL).When the data has changed because of board replaceing etc, check the default data of VIDEO OUT if destination code is right. If not, rewriteto the right value.

VIDEO OUT Default Data

Writing Method:1) Select page: 00, address: 01 and set data: 01.2) Select page: 4F, address: 8D, and set data: 00 (NTSC) or data: 01 (PAL).3) Select page: 4F, address: A2, and set data: 00 (NTSC) or data: 01 (PAL).4) Select page: 40, address: 38, and set data: 00.5) Click [Save] on the SEUS screen.6) Select page: 80, address: 34, and check that the data is “00”.7) Select page: 80, address: 30, and check that the data is “00”.8) Select page: 00, address: 01, and set data: 00.

Initial Language Data Check

If the SY-134 board was replaced, initial language setting may be changed. Accordingly, change the following data so as to set same initiallanguage as that of the set distributing in each region.

Initial language: Language displayed at the next starting if the setting of Setup menu was reset.It is different from the language setting selectable with the menu.

Initial Language Data

Page Address Data Language GP1 GP2 GP3 GP4

4F 8C

00 English z z z

01 Japanese z

04 Spanish z z

06 Portugal z

08 Simplified Chinese z

0B Russian z

0D Korean z

Note: GP1 is fixed to Japanese.GP2 is fixed to English.GP3 is either English, Spanish, or Russian.GP4 is either English, Spanish, Portugal, Simplified Chinese, or Korean.

Writing Method:1) Select page: 00, address: 01 and set data: 01.2) Select page: 4F, address: 8C, and set the Initial Language Data.3) Select page: 40, address: 38, and set data: 00.4) Click [Save] on the SEUS screen.5) Select page: 80, address: 34, and check that the data is “00”.6) Select page: 80, address: 30, and check that the data is “00”.7) Select page: 00, address: 01, and set data: 00.8) Turn off the camera.9) Turn on the camera. Execute “Initialize” of Setup screen.10) Check the language displayed when the camera starts.

Address

00

00

01

01

8D

A2

4F

4F

PageData

NTSC PAL

2-1

2. DISSASSEMBLY

DSC-T5_L2

NOTE FOR REPAIR

• Make sure that the flat cable and flexible board are not cracked of bent at the terminal.Do not insert the cable insufficiently nor crookedly.

• When remove a connector, dont’ pull at wire of connector. It is possible that a wire is snapped.

• When installing a connector, dont’ press down at wire of connector.It is possible that a wire is snapped.

• Do not apply excessive load to the gilded flexible board.

Cut and remove the part of gilt which comes off at the point.(Be careful or some pieces of gilt may be left inside)

DISCHARGING OF THE ST-126 BOARD’S CHARGING CAPACITOR (C005)

The charging capacitor (C005) of the ST-126 board is chargedup to the maximum 300 V potential.There is a danger of electric shock by this high voltage when thecapacitor is handled by hand. The electric shock is caused bythe charged voltage which is kept without discharging when themain power of the unit is simply turned off. Therefore, theremaining voltage must be discharged as described below.

Preparing the Short JigTo preparing the short jig, a small clip is attached to each end ofa resistor of 1 kΩ /1 W (1-215-869-11).Wrap insulating tape fully around the leads of the resistor toprevent electrical shock.

1 kΩ/1 W

Wrap insulating tape.

Note: High-voltage cautions

Discharging the CapacitorShort-circuit between the two points with the short jig about 10 seconds.

R:1 kΩ/1 W (Part code: 1-215-869-11)

Two soldering

Flat table

Speaker (SP901)SW-455 flexible board

SW-455 flexible board Speaker (SP901)

Horizontal

Put the speaker (SP901) and SW-455 flexible board on a flattable when you solder.It is important that each back become the horizontal.

Ver 1.2 2005.10

NOTE FOR INSTALLATION OF SPEAKER (SP901) AND SW-455 FLEXIBLE BOARD

DSC-T5_L22-3 2-4E

The following flow chart shows the disassembly procedure.

2-1. DISASSEMBLY

HELPHELP

1

2

3

4

1 Screw (M1.4) x32 Cabinet bottom3 Multi cover4 Open the BT lid.5 Screw (M1.4) x36 Close the BT lid.7 Cabinet (rear) block

1 Open the BT lid.2 Claw x23 BT lid

The BT lid is not removed unless there is the rear cabinet.When removing the BT lid, the rear cabinet must be in the assembled state.

How to disassemble BT lid

1 Open the BT lid.2 Claw x23 Rifting up the Control switch block.4 Connector x15 Control switch block

1 Flexible board x42 Screw (M1.7) x13 Boss x24 Remove the SY board.

5 Flexible board x16 SY board7 Claw x28 SW board

1 Hook x12 Rifting up the ST board.3 Flexible board x24 ST board

1 Hook x12 Remove the D901, LCD901.

3 Hook x24 D901, LCD901

1 Connector x22 Lens block assembly

8 Screw (M1.4) x19 Cabinet (front) assembly0 Discharging the Capacitor.

1

3

4

3

2

5

6

8

7

7

1

1

1

2

34

1

2

2

3

4

5

2

1

1

2

3

4

5

5

6

7

8

9

0

5

1

3

2

Refer to page 2-1 " Discharging of the ST-126 board's charging capacitor (C005) ", when discharging the capacitor.

HELP

Ver 1.2 2005.10

Refer to page 2-1 “Note for installation of speaker(SP901) and SW-455 flexible board”, when changethe speaker (SP901)

HELPDSC-T5_L2

HELPSheet attachment positions and procedures of processing the flexible boards/harnesses are shown.

When mounting the BT lid, fit a BT hinge spring in a space between BT hinge plate and BT lid.

BT lid

Sheet

BT hinge spring

BT lid

BT hinge plate

BT hinge spring

BT lid

BT hinge plate

Cabinet (upper) sheet (A)

Stroboscope insulating sheet

Control switch block

F radiation sheet

Cabinet (front) assembly

Control switch block

HELPDSC-T5_L2

Panel (FP) protection sheet

BT holder assembly

BT holder assembly

SY radiation sheet

SY-134 board

IC101

JK-292 flexible board

Install the JK-292 flexible board so that the lithium secondary battery is housed in a recess of the BT holder assembly.

Flexible board (LCD901)

JK-292 flexible board

Lithium secondary battery

DSC-T5_L2

LinkLink

3. BLOCK DIAGRAMS

OVERALL BLOCK DIAGRAM (2/2)

OVERALL BLOCK DIAGRAM (1/2) POWER BLOCK DIAGRAM

DSC-T5_L2

3-1. OVERALL BLOCK DIAGRAM (1/2)

3-1 3-2

( ) : Number in parenthesis ( ) indicates the division number of schematic diagram where the component is located.

3. BLOCK DIAGRAMS

A : VIDEO SIGNALA : AUDIO SIGNALA : VIDEO/AUDIO SIGNAL

SY-134 BOARD (1/2)

XCS_FE

VSUB_CONT_PREVSUB_CONT_POST

F2

U22

E1

K5 G4 H4L5 H2 H1J1 J2 M5J4 K4 M6

K2 K1

CLKTGOCAMERA DSP, CPU

LENS CONTROL,MODE CONTROL

(2/7)

J5CA_FD

H5CA_HD

CA_AD00 – CA_AD13

LENS

CCDIMAGER

IC002

CD-587 FLEXIBLE BOARD

15

20

60

85

53

26271819

37404448

LENS BLOCK

CN601

ZOOMMOTOR

M

FOCUSMOTOR

M

FOCUSRESET

SENSOR

ZOOMRESET

SENSOR

2356

20ı

2830ı

32

15

LENS TEMPSENSOR

BUFFERQ003

10

17

62919

7276

R23T4

11

13

Q001

Q002

1 - 5 7 - 911 - 14

CCD_OUT

POWER_SAVE

V1A, V1B, V2, V3A, V3B, V4, V5A, V5B, V6, V7A, V7B, V8

H1A, H2A, H1B, H2B

VHLDVST

98

RG

24

Q101

CCD SIGNALPROCESSOR,

TIMINGGENERATOR

(1/7)

IC101

5 6 8 9 11 12 16 79 88 90

91 102

23 82

87

SHTCSUB

Q102

56

86

XCAM_DR_CSP21D4

80

77

97 98 100101 103 104105 3 2 4 710 14 18

8993

J25

U4V4

LENS_TMP

IRIS(METER)

IRISMOTOR

M

IC201

B4B5B3A3

18ı

21

1ı4

5ı8

14

FOCUSMOTORDRIVER

IRIS_A_DIR, IRIS_A_BRK, IRIS_B_DIR, IRIS_B_BRK

FOCUS_A_DIR, FOCUS_B_DIR, FOCUS_EN

ZOOM_A_DIR, ZOOM_B_DIR, ZOOM_EN

FC_SENSZM_SENS

ZOOMMOTORDRIVER

IRIS MOTORDRIVER

FOCUS_A, A, B, B

ZOOM_A, A, B, B ZOOM_A, A, B, B

IRIS_A, A, B, BIRIS_A, A, B, BCN602

11

FOCUS_A, A, B, B

F2E2D2B1

D6E6B7C6

D5A6B6C5

F5E5D3F1

A2C3C4A1

LENS DRIVE(3/7)

10

N4P6P4R2

L2N5L4

N6M2N2

ST-126 BOARD (1/2)

R4

05

V23R22

AB22

STRB_CHGXSTRB_FULL

ST_UNREG

Q001

FLASHUNIT

FLASHCONTROL,CHARGE

CONTROL

5

78

6

2

IC001

XE_H

TRIGGERTRIGGER_GND

XE_L

+C005

CHARGINGCAPACITOR

D001

3

5 4

1

1

T001

STRB_CHG_CONT4 STRB_ON

STRB_CHARGEXSTRB_FULL

CN603(1/2)

1110

9I_PEAK8STRB_ON

CN002(1/2)

109

8

76

7

D003SELF TIMER/

AF ILLUMINATORXAF_LED XAF_LED

SAN_AUOUT

XSAN_RST_OUT

XSAN_RST_OUT

2 OVERALL (2/2)(PAGE 3-3)

USB_DP, USB_DM

AF4

K26L26

AC1AD1

D901BACKLIGHT

COLORLCD

PANEL

U2R6

E9B8

BL_H

21ı

28

CN609

CN001

LCD901

3031

3332

12

56

HSYNC, VSYNC

DCK

IC301(1/2)

XCS

PANEL UNIT

SAN_AUIN

Y26

T5

XCS_AUDIO

USB_VBUS

D8 D7E8 E7D6 D5E6 B4

AB6 AC4AE4 AE5AC5 AF6

BL_HBL_L OVERALL (2/2)

(PAGE 3-4)1

OVERALL (2/2)(PAGE 3-4)3

BL_L

BL_H11

CN002 (2/2)CN603

(2/2)

BL_L12

12

13

W25

D9

XRESET

LCD_HD, LCD_VD

LCD_CK

XCS_PANEL

XSAN_RST_OUT

ST-126 BOARD (2/2)

LCD_D0 – LCD_D7

Q301

CPU_

D0 –

CPU

_D15

CPU_

D0 –

CPU

_D15

XCPU_CS4

IC40232M BURST FLASH

(4/7)

IC403256M SDRAM

(4/7)

IC40132M AND FLASH

(4/7)

D3 C5 E3 G4 G6 H7 H5 H2 G2 J3 G3 G5 J6 H6 H4 J4 J5 H3 J7

AB13 AA13 AE13 AF13AF12 AE12 AA12 AC12AC11 AB12 AE11 AF11AE10 AB11 AC10 AB10

F7 E6 E5 G5E4 G3 E3 G1G7 F6 F5 F4D5 F3 F2 E2

E8 D8 C8 B8 A8 B7 A7C7 A2 B2 C2 A1 B1 C1D2 D1 D4 B6 A6 C6 B3

AF21 AF20 AE20 AB18 AB19 AC19 AB16AE19 AF19 AF18 AE18 AA15 AC18 AC17

AB15 AE17 AF17 AE16 AB14 AC16 AC15 AE14

B5

K3AC6

XCPU_CS0 E7SAN_27M_CLKO B4

AE6AF9

DSP_QCLK J1DSP_QCLKE J2

A18A17

J1

CPU_A01 – CPU_A21, CPU_A25

CPU_D0 – CPU_D15

CPU_

A01 –

CPU_

A21

CPU_

A20,

A21,

A25

DSP_DQ00 – DSP_DQ31, DSP_DQM0 – DSP_DQM3

DSP_AQ00 – DSP_AQ12, DSP_QBA0, DSP_QBA1

R8 N7 R9 N8 P9 M8 M7 L8 L2 M3 M2 P1 N2 R1 N3 R2 E8 D7 D8 B9 C8 A9 C7 A8 A2 C3 A1 C2 B1 D2 D3 E2 K9 K1 F8 F2

D21 D22 D20 B22 A22 A23B23 E20 E21 B24 A24 A25B25 C25 C26 B26 E10 A10D10 E11 B10 A11 B11 E12D11 D12 F12 B12 A12 E13D13 D14 F13 B15 F14 E14

G8 G9 F7 F3 G1 G2 G3 H1 H2 J3 G7 H9 H3 J7 H8

D17 D18 D16 B18 A19B19 E16 D19 E19 E17B20 A20 E18 B21 A21

29

34VCOMHF25 LCD_ADJ1

1535

SI, SCLK

D0 – D7

SAN1_SO, XSAN1_SCK

SAN1_SO, XSAN1_SCK

SAN1_SO, XSAN1_SCK

SAN1_SO, XSAN1_SCK

FP-298FLEXIBLEBOARD (1/2)

FP-298FLEXIBLEBOARD (2/2)

V_LINE_OUTH26U23 VIDEO_AMP_ON

SAN_VOUTVIDEO AMP

(2/7)

534

IC303BUFFER

Q305

MS_BS, MS_D0 – MS_D3, MS_CLK

DSC-T5_L23-3 3-4

3-2. OVERALL BLOCK DIAGRAM (2/2) ( ) : Number in parenthesis ( ) indicates the division number of schematic diagram where the component is located.

A : VIDEO SIGNALA : AUDIO SIGNALA : VIDEO/AUDIO SIGNAL

USB_VBUS

SY-134 BOARD (2/2)

V_OUTA_OUT_L

XAV_JACK_IN

USB_VBUS

V_LINE_OUTCN605

USB_DP, USB_DM

30

2526

AU_LINE_OUT 28

XAV_JACK_IN33

23USB_VBUS

USB_DP, USB_DM 1012

6

2016

26

CN001MULTI

CONNECTOR

JK-292 FLEXIBLE BOARD

AUDIO AMP(5/7)

IC501

E6

D1

B6

05

MIC901

V_LINE_OUT

SAN_AUOUT

SAN_AUIN

XCS_AUDIO

XSTRB_LED

E5

E4

MIC_SIG

2OVERALL (1/2)(PAGE 3-2)

MODEDIAL

S001(SHUTTER)

POWER

CONTROL SWITCH BLOCK(RL51860)

S002

S003

BATTERYCHARGE

DETECTOR

15V/–7.5V REG(6/7)

Q3022 4

3 XPOWER_ON XPOWER_ON

MODE_DIAL0

J23G25

K23L23

6XPWR_LEDD001

(POWER)

USB_DP, USB_DM

DC/DCCONVERTER

(6/7)

IC001

IC302

IC002

D_3.2V

ST_UNREG

MS_VCC

A_3.2V

D_1.8VCAM_2.9V

CAM_–7.5VCAM_15V

D_1.2VM_5V

SAN1_SO, XSAN1_SCK F3E3

CN608

XAV_JACK_IN

USB_VBUSXMS_IN

SAN0_SI, SAN0_SO, XSAN0_SCK

A9

A8

X00132.768kHz

S001 – 010

KEY_AD0, KEY_AD1

CN607

A5A2

U25

R21

V25

109

8

1

XAE LOCK_SWXSHUTTER_SW

CN606

+

G

BH001BATTERY

TERMINAL

CHARGE_V

VL_3V

BATT_GNDI

BATT_SIG

CHARGE_V

BATT_SIG

A6

X30112MHz

E22

D23

E4

L22

F9 OVERALL (1/2)(PAGE 3-2)

1

OVERALL (1/2)(PAGE 3-2)

3

BL_L

C7

S001(LENS COVER) D7

AA23

AB25

AA26

XPWR_OFF

W23 XCS_DD A6T25

Y4

MS_PWR_ON D3

B10C9

E9

A4

BL_H

N21P23

FUNCTIONKEY

D610(MS ACCESS)

B7

K25

P25

BATT_SENS

–7.5V_ON

G5

R26 XDD_RST_OUT A7

B8

H1

XAF_LED

BT-028 FLEXIBLEBOARD

SW-455 FLEXIBLE BOARD

IC301(2/2)

FRONT CONTROL(2/7)

(2/7)

C6C5B6

AA5AB5Y5

MS_BS, MS_D0 – MS_D3, MS_CLKMS_BS, MS_D0 – MS_D3, MS_CLK MEMORYSTICKDUO

2ı578

6

CN604

XMS_IN

BATT_XEXTBATT/XEXT

XSTATION_IN

13

121120

19

XSTATION_IN

KEY_A/DA, KEY_A/DBCRADLE_AD1, CRADLE_AD2

XACV_IN

BATT_SIG

XACV_IN

XSTATION_IN

CRADLE_AD1, CRADLE_AD2 159

ACV_UNREGACV_UNREG 2325

CHARGE_VCHARGE_V 1721

19

2

XPOWER_ONXPOWER_ON 22 7

BT001LITHIUMBATTERY

1ı5

14ı

18

EVER_SRAM

Q001, 002

D002(FLASH CHARGE)

32

65

7

SP901SPEAKER

SP+, SP– SP+, SP–

1ı4

6ı

10

5

DSC-T5_L23-5 3-6E

3-3. POWER BLOCK DIAGRAM ( ) : Number in parenthesis ( ) indicates the division number of schematic diagram where the component is located.

05

SY-134 BOARDJK-292 FLEXIBLEBOARD


BT-028 FLEXIBLEBOARD

ST-126 BOARDFP-298 FLEXIBLEBOARD

VO1-1 D_3.2V

A_3.2V

AU_3.0V

D_3.2V

D_3.2V

LX2

PWR1-1A1

UNREG1-2K1UNREG1-1J1

F1VO1-2 F2VFB1 H2

BG4 G9

PSG4 G8VFB4 F7

TG4 F10

C10

VFB2 D8

IC001

DC/DC CONVERTER(6/7)

IC002

15V/–7.5V REG(6/7)

LDO2 A3

LX5-1 J9

LDO2IN B3

PWR2D10

UNREG2-1J6UNREG2-2K6

D_1.8V

D_1.2V

CAM_15V

CAM_–7.5V

PWR1-3C2PWR1-2B1

LDO3 A2

LDO3IN B2

PWR56OUT2 K7PWR56OUT1 J7

CAM_2.9V

MS_PWRG2 MS_PWR_IN G1MS_VCC

LX5-4 K10LX5-3 K9LX5-2 J10

UNREG

L002

L001

M_5V

F002

F001

Q001,002

F003

CN603

14ı

181721

1ı5

2325

32

1319

24

19

1ı4

6ı

10

5

CN606

CN605

12

11

12

13

14

BH001BATTERY

TERMINAL

CHARGE_V

BATT_SIG BATT_SIG

CHARGE_V

BATT_GND

BATT_XEXT BATT/XEXT

ACV_UNREG

XCHG_ON

BL_HVO3 E9

LX3 E10

BL_L

M_5V

VL3 F9

VFB5 H9

D005

D006

D302

D001

L005

EVER_SRAM

XACV_IN

XACV_IN

D004

D003

D001

BT001LITHIUMBATTERY

CN001MULTI

CONNECTOR

VL_3V

Q004, 005

SWITCHINGQ003

D009

D008 D007

Q302

BATTERYCHARGEDETECT

DC CONTROL

L006

B8 RTCBAT

H1 LDO1

SAN0_SI, SAN0_SO, XSAN0_SCK

AA23 XPWR_OFF

P25 –7.5V_ON

W23 XCS_DD A6

T25

V25

AA26

AB25Y4

MS_PWR_ON

MS_PWR_OND3

B7

K25 BATT_SENS UNREGMONCE

G5

R26 XDD_RST_OUT A7

IC301

IC302

CAMERADSP,CPU,LENS

CONTROL,MODE

CONTROL,FRONT

CONTROL(2/7)

(2/7)

C6C5B6

AA5AB5Y5

XPWROFF

XRESET

SOSISCLK

L0073 4

7 6

REG3

REG2

1STB

VEE

VCC

17

CN609VDD

ST_UNREG ST_UNREG

L302

L301

L304

AUDIO AMP(5/7)

VIDEO AMP(2/7)

IC501

IC303

SDRAM_VCC

D_3.2V

A_3.2V

AU_3.0V

D_1.2V

SDRAM_VCC

D_3.2V

D_3.2V

A_3.2V

AU_3.0V

D_1.2V

MS_VCC9

4

T001

FLASHUNIT

L001

L601COLOR

LCDPANEL

LCD901

PANEL UNIT

MEMORYSTICKDUO

CN604

CN608

FLASH CONTROL,CHARGE CONTROL

IC001

CAM_15V_CD

CAM_–7.5V

CAM_2.9V

D_3.2V

D_3.2V

D_3.2V

CAM_15V

CAM_–7.5V_CD

17

10

CN601

L103

L104

L102

L101

FB108

CCD IMAGER

IC002

CAMER MODULE(1/7)

IC101

FB107

FB106


CN602ZM_SENS_VCC

12

FC_SENS_VCC15

IC201

LENS DRIVE(3/7)

BURST FLASH(4/7)

IC402

AND FLASH(4/7)

IC401

256M SDRAM(4/7)

IC403

3.0V REG(5/7)

IC502

31 VOUTVIN

D901BACKLIGHT

BL_H

CN001

56

12

BL_L

ST_5V

BL_H

CN002

BL_L

ST_5V

AF_5V

12

13

14

15

1ı3

24

L003

D003SELF TIMER/

AF ILLUMINATOR

LENS BLOCK

FOCUSRESET

SENSOR

ZOOMRESET

SENSOR

D001(POWER)

D002(FLASH CHARGE)

+

I

G

DSC-T5_L24-1 4-2

4-1. FRAME SCHEMATIC DIAGRAM

4. PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS

FRAME

21PCN602

1FOCUS_A

2FOCUS_B

3FOCUS_A

4FOCUS_B

5ZOOM_B

6ZOOM_A

7ZOOM_B

8ZOOM_A

9TEMP_GND

10LENS_TEMP

11ZM_SENS

12ZM_SENS_VCC

13ZM_SENS_GND

14FC_SENS

15FC_SENS_VCC

16FC_SENS_GND

17N.C.

18IRIS_A

19IRIS_A

20IRIS_B

21IRIS_B

CN604 12P

1

2

3

4

5

6

7

8

9

10

11

12

14P

CN

002

1234567891011121314

10PCN606

1

2

3

4

5

6

7

8

9

10

33PCN601

1

2

3

4

5

6

7

8

9

10

11

12

13

14

15

16

17

18

19

20

21

22

23

24

25

26

27

28

29

30

31

32

33

15P

CN

603

123456789101112131415

CN001 28P

24

68

1012

1416

1820

2224

26

13

57

915

1311

1719

2123

25

6PCN001

1

2

3

4

5

6

39P

CN

609

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39

6PCN607

1

2

3

4

5

6

10P

CN

608

12345678910

33PCN605

1

2

3

4

5

6

7

8

9

10

11

12

13

14

15

16

17

18

19

20

21

22

23

24

25

26

27

28

29

30

31

32

33

GI

BH001

2

1

3

CCD

LENS BLOCK

MS_CLK

MS_D0

MS_VCC

MS_D3

REG_GND

XMS_IN

MS_D1

REG_GND

MS_D2

MS_BS

I_P

EAK

AF_

5V

ST_

UN

REG

REG

_GN

D

ST_

UN

REG

STR

B_O

N

XS

TRB

_FU

LL

XA

F_LE

D

ST_

5V

BL_

H

REG

_GN

D

BL_

L

REG

_GN

D

STB

_CH

AR

GE

BATT_GND

BATT_GND

CHARGE_V

CHARGE_V

BATT_GND

BATT_SIG

CHARGE_V

BATT_GND

CHARGE_V

BATT_GND

REG_GND

POWER_SAVE

V7A

VST

CCD_OUT

CSUB

CAM_-7.5V_CD

V4

REG_GND

REG_GND

VHLD

REG_GND

V6

V5A

V3B

H2A

REG_GND

CAM_15V_CD

V5B

V1B

H2B

V8

H1B

V7B

V1A

V2

REG_GND

REG_GND

V3A

RG

REG_GND

SHT

H1A

BL_

H

ST_

UN

REG

AF_

5V

REG

_GN

D

STR

B_O

N

I_P

EAK

ST_

UN

REG

REG

_GN

D

REG

_GN

D

ST_

UN

REG

XA

F_LE

D

XS

TRB

_FU

LL

BL_

L

STB

_CH

AR

GE

ST_

5V

ACV_GND

ACV_UNREG

USB_GND

XPOWER_ON

XAV_JACK_IN

USB_GND

XCHG_ON

ACV_GNDUSB_VBUS

XSTATION_IN

CHARGE_V

ACV_UNREG

SET_ID_IN

CHARGE_V

V_GND

KEY_A/DA

USB_DM

V_OUT

A_GND

BATT_XEXT

KEY_A/DB

NC

NC

A_OUT_L

ACV_GND

USB_DP

BL_H

BL_H

N.C

BL_L

BL_L

N.C

NC

NC

VR

DC

K

VG

L

VC

OM

TFT-

CO

M

NC

(VR

2)

VS

S

XR

ESET

XC

SSI

SC

LK

VS

YN

C

HS

YN

C

D7

D6

D5

D4

D3

D2

D1

D0

VS

CO

MD

C

VD

D

VG

H

VD

D2

C1+C1-

C3+C3-

CO

MC

VC

OM

H

C2+C2-

VS

S

TFT-

CO

M

VC

OM

KEY_AD1

KEY_AD0

REG_GND

SP+

SP-

REG_GND

XS

TRB

_LED

XA

E_LO

CK

_SW

D_3

.2V

MIC

_GN

D

XP

WR

_LED

XP

OW

ER_O

N

REG

_GN

D

MIC

_SIG

MO

DE_

DIA

L0

XS

HU

TTER

_SW

CRADLE_AD1

USB_DM

CHARGE_V

ACV_GND

V_LINE_OUT

XPOWER_ON

CRADLE_AD2

USB_GND

CHARGE_V

CHARGE_V

BATT/XEXT

ACV_GND

ACV_GND

XSTATION_IN

ACV_GND

XAV_JACK_IN

USB_VBUS

ACV_UNREG

CHARGE_V

V_GND

USB_DP

ACV_UNREG

ACV_UNREG

XCHG_ON

USB_GND

VL_3V

ACV_UNREG

CHARGE_V

SET_ID_IN

A_GND

ACV_GND

AU_LINE_OUT

ACV_UNREG

CONTROLSWITCHBLOCK

MIC

2.5INCH

LCD MONITOR

LCD901

COLOR

D901 BACKLIGHT

BOARD

FP-298FLEXIBLE

BOARDST-126

(FLASH DRIVE) FLASHUNIT

C005CHARGINGCAPACITOR

IMAGER

(CCD IMAGER)BOARD

FLEXIBLECD-587

BOARDFLEXIBLE

(CONTROL SWITCH)SP901

SPEAKER

TO AV/USB MULTI CABLE OR CRADLE

28

(MULTI CONNECTOR)

27

JK-292

(MULTI CONNECTOR)BOARD

FLEXIBLE

BT001

BATTERYLITHIUM

TERMINALBATTERY

BOARD(BATTERY IN)

BT-028FLEXIBLE

(AUDIO)

SY-134 BOARD

(LENS DRIVE)(CAMERA DSP, CPU)

(LCD, MS, CONNECTOR)(DC/DC CONVERTER)

(AND FLASH, BURST FLASH, SDRAM)

(CAMERA MODULE)

(4/7)

(6/7)

(3/7)

(1/7)(2/7)

(7/7)

(5/7)

STICKMEMORY

DUO

05

SW-455

(RL51860)MIC901

DSC-T5_L2

ST-126 BOARD (FLASH DRIVE)

CD-587 FLEXIBLE BOARD (CCD IMAGER)

CONTROL SWITCH BLOCK (RL51860)

BT-028 FLEXIBLE BOARD (BATTERYIN)

SW-455 FLEXIBLE BOARD(CONTROL SWITCH)

JK-292 FLEXIBLE BOARD(MULTI CONNECTOR)

FP-298 FLEXIBLE BOARD (SY-ST CONNECTION BOARD)

LinkLink

4-2. SCHEMATIC DIAGRAMS

WAVEFORMSCOMMON NOTE FOR SCHEMATIC DIAGRAMS

4-5DSC-T5_L2

4-2. SCHEMATIC DIAGRAMS4-2. SCHEMATIC DIAGRAMS

4-2. SCHEMATIC DIAGRAMS

1. Connection

2. Adjust the distance so that the output waveform ofFig. a and the Fig. b can be obtain.

When indicating parts by reference number, pleaseinclude the board name.

(For schematic diagrams)• All capacitors are in µF unless otherwise noted. pF : µ

µF. 50 V or less are not indicated except for electrolyticsand tantalums.

• Chip resistors are 1/10 W unless otherwise noted.kΩ=1000 Ω, MΩ=1000 kΩ.

• Caution when replacing chip parts.New parts must be attached after removal of chip.Be careful not to heat the minus side of tantalumcapacitor, Because it is damaged by the heat.

• Some chip part will be indicated as follows.Example C541 L452

22U 10UHTA A 2520

• Constants of resistors, capacitors, ICs and etc with XXindicate that they are not used.In such cases, the unused circuits may be indicated.

• Parts with differ according to the model/destination.Refer to the mount table for each function.

• All variable and adjustable resistors have characteristiccurve B, unless otherwise noted.

• Signal nameXEDIT → EDIT PB/XREC → PB/REC

• 2: non flammable resistor• 5: fusible resistor• C: panel designation• A: B+ Line• B: B– Line• J : IN/OUT direction of (+,–) B LINE.• C: adjustment for repair.• A: not use circuit• Circled numbers refer to waveforms.(Measuring conditions voltage and waveform)• Voltages and waveforms are measured between the

measurement points and ground when camera shootscolor bar chart of pattern box. They are reference valuesand reference waveforms.(VOM of DC 10 MΩ input impedance is used)

• Voltage values change depending upon inputimpedance of VOM used.)

Kinds of capacitorCase size

External dimensions (mm)

Yello

w

A AB BA=B

Fig. a (Video output terminal output waveform)

H

Cya

nG

reen

Whi

teM

agen

ta

Red

Blu

e

Fig.b (Picture on monitor TV)

CRT picture frame

Electronic beamscanning frame

THIS NOTE IS COMMON FOR SCHEMATIC DIAGRAMS(In addition to this, the necessary note is printed in each block)

Pattern box

Pattern box PTB-450J-6082-200-A orSmall pattern boxPTB-1450J-6082-557-A

Color bar chart

For PTB-450:J-6020-250-A

For PTB-1450:J-6082-559-A

Pattern box Front of the lens

L = About 30 cm (PTB-450)L = About 13 cm (PTB-1450)

L Camera

Precautions for Replacement of Imager• If the imager has been replaced, carry out all the adjustments

for the camera section.• As the imager may be damaged by static electricity from

its structure, handle it carefully like for the MOS IC.In addition, ensure that the receiver is not covered withdusts nor exposed to strong light.

The components identified by mark 0 or dotted line withmark 0 are critical for safety.Replace only with part number specified.

Les composants identifiés par une marque 0 sontcritiques pour la sécurité.Ne les remplacer que par une pièce portant le numérospécifie.

DSC-T5_L2

XXC002

Note: Voltage and Waveform of mounted IC002 onCD-587 flexible board can not be measured, becausethey are mounted by the side of the lens.

NO MARK:REC/PB MODE R:REC MODE P:PB MODE

Note: CD-587 flexible complete board and IC002 arenot supplied, but there are included inCCD block assy.

1R11.2/P00

R11.2/P0R12/P0

R15.1/P0

0

R3.4/P0

IC002ICX495CQZ-13

4

V3A

5

V3B

6

VS

T

7

V4

8

V5A

9

V5B

10

VH

LD

12 V7A

13 V7B

14 V8

15 CCD-OUT

16 VH

17 RG

22

WG

ND

23

SU

B

24

CS

UB

18

H1B

19

H2B

20

RS

S3

21

GN

D

26H1A

27H2A

1V1A

2V1B

3V2

11

V6

25

VL

0R006

22kR003

1200R005

0.1u10V

C005

16V0.1uC003

DTC144EMT2LQ002 1500

R004

0.1u16V

C004

DTC144EMT2LQ001

3900R002

LND031

LND025

LND022

LND002

LND005

LND006

LND033

LND003

LND026

LND024

LND014

LND032

LND004

LND007

LND018

LND009

LND021

LND028

LND019

LND023

LND011

LND029

LND013

LND012

LND010

LND030

LND001

LND008

LND015

LND017

LND020

LND027

LND016

2SC39320S2S0Q003

1

A

V8

REG_GND

V5B

CAM_-7.5V_CD

CAM_15V_CD

V6

POWER_SAVE

H1A

RG

V7B

REG_GND

V3A

H2A

REG_GND

V1B

REG_GND

REG_GND

V5A

REG_GND

CCD_OUT

VST

H1B

V1A

V7A

SHT

V2

VHLD

CSUB

V3B

REG_GND

REG_GND

V4

H2B

28

23

24

15

31

21

16

18

14

12

5

22

8

6

1

30

2

7

4

3

33

10

11

26

19

9

17

29

27

32

13

20

25

SY-134(1/7)

of LEVEL3PAGE 4-9

CN601


C

62 97

G

4

05

8

XX MARK:NO MOUNT

D

CCD IMAGER

F

B

E

53

CCD IMAGER

IC002

BUFFER

SWITCH

SWITCH

4-7 4-8 CD-587

DSC-T5_L2

Schematic diagrams of the SY-134 board are not shown.Pages from 4-9 to 4-22 are not shown.

DSC-T5_L24-23 4-24 ST-126

FP-298

PAGE 4-27

FLEXIBLE

of LEVEL2

LND021-LND034

NO MARK:REC/PB MODE

4.2

4.2

5

0

0

0

3.3

0

265

0

LND032

XE_L

33R001

1MR002

LND029

1MR003

C0060.047u250V

LND031

XE_H

1uC001

6.3V22u

C002

CY25BAJ-8F-T23Q001

1

8 5

234

67

LND030

CRF02(TE85R)D001

6PCN001

1

2

3

4

5

6

T001

4

1

2 3

5

IC001TPS65552DGQR

1 VBAT

2 SW

3 VCC

4 F_ON

5 I_PEAK 6G_IGBT

7XINCHG

8CHG

9PGND

10NC

11

HG

ND

0.1uC003

0R004

14PCN002

1

2

3

4

5

6

7

8

9

10

11

12

13

14

85uC005

315V

TLOH9203(SONY)D003

1

2

34

5

6

2.2uHL001

1

A

TRIGGER

FLASH DRIVE

TRIGGER_GND

BL_L

BL_L

N.C

BL_H

BL_H

N.C

I_PEAK

STB_CHARGE

XSTRB_FULL

ST_5V

STRB_ON

ST_UNREG

REG_GND

REG_GND

XAF_LED

BL_L

BL_H

ST_UNREG

REG_GND

AF_5V

D901BACKLIGHT

AF ILLUMINATORSELF TIMER/

CHARGE CONTROL

IC001FLASH CONTROL

ST-126 BOARD

C

62 974

05

8

XX MARK:NO MOUNT

D

FLASH DRIVE

B

E

53

CAPACITORCHARGING

FLASHUNIT

• Refer to page 4-5 for mark 0.

DSC-T5_L24-25 4-26 JK-292

Note: CN001 (multi connector) is not supplied, but this is included in JK-292 flexible complete board.

LND024

LND015

LND016

LND026

LND013

LND004

LND002

LND028

LND029

LND007

LND009

LND019

LND021

LND032

LND030

LND020

LND006

LND023

LND010

LND027

LND031

LND001

LND003

LND008

CN00128P

2

4

6

8

10

12

14

16

18

20

22

24

26

1

3

5

7

9

15

17

19

21

23

25

27

28

LND018

LND011

LND025

LND012

LND022

LND017

LND005

LND033

LND014

BT001

MAZW068H0LS0D001

3

21

D003MAZS068008SOMAZW068H0LS0

D002

3

2

1

33R002

1

A

SET_ID_IN

USB_VBUS

XPOWER_ON

ACV_GND

USB_DM

CHARGE_V

XSTATION_IN

ACV_GND

STATIC_GND

A_GND

KEY_A/DB

ACV_UNREG

USB_GND

CHARGE_VV_GND

BATT_XEXT

ACV_GND

XAV_JACK_IN

V_OUT

USB_DP

ACV_UNREG

KEY_A/DAA_OUT_L

USB_GND

XCHG_ON

ACV_GND

A_GND

USB_GND

SET_ID_IN

XAV_JACK_IN

XSTATION_IN

ACV_UNREG

CLADLE_AD2

ACV_UNREG

BATT/XEXT

USB_DM

USB_GND

ACV_GND

USB_DP

USB_VBUS

AU_LINE_OUT

CLADLE_AD1

ACV_UNREG

XPOWER_ON

V_GND

ACV_GND

ACV_UNREG

ACV_GND

XCHG_ON

ACV_GND

CHARGE_V

CHARGE_V

VL_3V

ACV_UNREG

CHARGE_V

CHARGE_V

CHARGE_V

V_LINE_OUT

BATTERYLITHIUM

28

23

24

15

31

21

16

18

14

12

5

22

8

6

1

30

2

7

4

3

33

10

11

26

19

9

17

29

27

32

13

20

25

PAGE 4-21CN605

SY-134

of LEVEL3

(7/7)

(MULTI CONNECTOR)TO AV/USB MULTI CABLE OR CRADLE


C

62 974

05

8

XX MARK:NO MOUNT

D

MULTI CONNECTOR

F

B

E

53

13

11NC

NC


DSC-T5_L24-27 4-28 SW-455, BT-028, FP-298, RL51860

PAGE 4-23of LEVEL2

ST-126CN002

NO MARK:REC/PB MODE

CONTROL SWITCH BLOCK (RL51860) is replaced as block,so that PRINTED WIRING BOARD is omitted.

LND005 BATT_SIG

LND006 BATT_GND

LND001 CHARGE_V

LND007 BATT_GND

LND002 CHARGE_V

LND004 CHARGE_V

LND008 BATT_GND

LND003 CHARGE_V

LND010 BATT_GND

GI

BH001

2

1

3

LND009 BATT_GND

1

A

9

3

1

10

8

5

2

7

4

6

BATTERYTERMINAL

(6/7)SY-134

of LEVEL3

CN606PAGE 4-19

BT-028 FLEXIBLE BOARD

2

C

4

BATTERY IN

05

B

XX MARK:NO MOUNT

3

LND004 REG_GND

LND006 REG_GND

LND015 AF_5V

LND011 XSTRB_FULL

LND014 ST_5V

LND010 STB_CHARGE

LND012 BL_H

LND002 ST-UNREG

LND005 REG_GND

LND003 ST-UNREG

LND007 XAF_LED

LND009 I_PEAK

LND008 STRB_ON

LND001 ST-UNREG

LND013 BL_L

LND021ST_UNREG

LND028I_PEAK

LND033ST_5V

LND023REG_GND

LND031BL_H

LND026XAF_LED

LND030XSTRB_FULL

LND032BL_L

LND024REG_GND

LND025REG_GND

LND027STRB_ON

LND029STB_CHARGE

LND022ST-UNREG

LND034AF_5V

1

A

9

3

11

14

13

1

15

12

10

8

5

2

7

4

6 6

4

7

2

5

8

10

12

1

13

14

3

11

9

CN603

SY-134(7/7)

of LEVEL3PAGE 4-21

FP-298 FLEXIBLE BOARD

2

C

4

05

D

B

53

SY-ST CONNECTION BOARD

S001

1

3

2

4

S004

1

3

2

4

S005

1

3

2

4

S002

1

3

2

4

S003

1

3

2

4

S006

1

3

2

4

S007

1

3

2

4

S009

1

3

2

4

S010

1

3

2

4

S008

1

3

2

4

1200R001

1500R002

3300R003

6800R004

1200R005

1500R006

3300R007

6800R008

LND001

LND002

LND003

LND004

LND005

LND006

LND008

SP+

LND007

SP-

1

A

KEY_AD1

KEY_AD0

REG_GND

SP+

SP-

REG_GND

5

6

1

2

4

3

MENU W T(ZOOM)IMAGE SIZE/DELETE

(5/7)

PAGE 4-18CN607

SY-134

of LEVEL3


C

62 74

05

XX MARK:NO MOUNT

CONTROL SWITCH

B

53

SP901SPEAKER

(SET)(SELF TIMER) (REVIEW)(FLASH)(MACRO)

SCREENDISPLAYON/OFF

3300R003

CL001

CL0021500R002

1200R001CL-270YG

D001

CL-270TLYD002

LND005

LND006

LND010

LND004

LND002

LND001

LND003

LND007

LND008

LND009

S003

B

6

A 1

2

3GS002

NO

S001

13

42

1

A

STILLMOVIE

(POWER) (GREEN)

AE LOCK

SHUTTER

(FLASH CHARGE)

PLAY

XSHUTTER_SW

MIC_GND

XAE_LOCK_SW

D_3.2V

MIC_SIG

XPOWER_ON

MODE_DIAL0

XSTRB_LED

XPWR_LED

REG_GND

(MODE DIAL)

9

3

1

10

8

5

2

7

4

6SY-134

CN608

of LEVEL3

(7/7)

PAGE 4-22

MICMIC901

POWER

(SHUTTER)


62

C

4

05

D

B

53

(YELLOW)


DSC-T5_L2

LinkLink

4-3. PRINTED WIRING BOARDS

ST-126 BOARD




SW-455 FLEXIBLE BOARD FP-298 FLEXIBLE BOARD

MOUNTED PARTS LOCATION

COMMON NOTE FOR PRINTED WIRING BOARDS

WAVEFORMS

4-31DSC-T5_L2

4-3. PRINTED WIRING BOARDS4-3. PRINTED WIRING BOARDS

• : Uses unleaded solder.• : Circuit board

: Flexible boardPattern from the side which enables seeing.

: pattern of the rear side(The other layers’ patterns are not indicated)

• Through hole is omitted.• Circled numbers refer to waveforms.• There are a few cases that the part printed on diagram

isn’t mounted in this model.• C: panel designation

THIS NOTE IS COMMON FOR PRINTED WIRING BOARDS

2 1

3

2 1

3

2 1

3

345

21

123

654

EB

C

31

5

2

46

123

654

31

5

2

46

123

54

4 3

1 2

31 2

45

53 4

12

14

23

46

2

5

31

12

43

14

23

• Chip parts.Transistor Diode

4-3. PRINTED WIRING BOARDS

DSC-T5_L24-34 CD-5874-33

CD-587 (2 layers)

: Uses unleaded solder.

C

BEC

BE

C002 C0

03

C004

C005

LND0

01LN

D002

LND0

03LN

D004

LND0

05LN

D006

LND0

07LN

D008

LND0

09LN

D010

LND0

11LN

D012

LND0

13LN

D014

LND0

15LN

D016

LND0

17LN

D018

LND0

19LN

D020

LND0

21LN

D022

LND0

23LN

D024

LND0

25LN

D026

LND0

27LN

D028

LND0

29LN

D030

LND0

31LN

D032

LND0

33

Q001Q002

Q003

IC002

R00

2

R00

3

R00

4

R00

5

R00

6

411

14 1

15

18 25

27

1 33


1-867-905- 11

1

C

B E

05

DSC-T5_L2

Printed wiring boards of the SY-134 boards are not shown.Pages from 4-35 to 4-38 are not shown.

DSC-T5_L2

ST-126 (4 layers)


4-39 4-40 ST-126

C002

C006

D003

T001

L001

1

5

2 3

4

1 3

46

ST-126 BOARD (SIDE A)

1-867-904- 11

D003SELF TIMER/

AF ILLUMINATOR

05

16

114

111 5

6101 4

58

CN00

1

CN002

C001

C003D001

IC001

LND029LND030

LND031LND032

Q001

R001

R002

R003

R004

A K

C005

ST-126 BOARD (SIDE B)

1-867-904- 11

FLASHUNIT

C005CHARGINGCAPACITOR

XE L

TRIGGER

TRIGGER GND

XE H

05

DSC-T5_L24-41

SW-455 (1 layer), BT-028 (2 layers), JK-292 (2 layers), FP-298 (1 layer)


4-42 SW-455, BT-028, JK-292, FP-298

SW-455

1-867-906-

>PI<

S001

S002

S003

S004 S005

S006

S007

S008

S009 S010

LND0

01LN

D002

LND0

03LN

D004

LND0

05LN

D006

LND007LND008

R001

R002R003

R004

R005

R006

R007 R008

2

13

4

21

3 4

21

3 4

2 1

34

2 1

34

2 1

34

2

1 3

4

2

1 3

4

2

13

42

13

4

1 6

SP901SPEAKER

SP+ SP–


1-867-906- 11

1 205

B

C

D

E

F

A

(ZOOM)S009

WS010

T

SCREENDISPLAYON/OFF

S006

MENUS008

(FLASH)

S003

(SELF TIMER)

S001

(MACRO)

S002

(REVIEW)

S004

(SET)

S005

IMAGE SIZE/DELETE

S007

BT-028

1-867-908-

>PI<

LND0

01LN

D002

LND0

03LN

D004

LND0

05LN

D006

LND0

07LN

D008

LND0

09LN

D010

1

2

3

1 10


1-867-908- 11

+

I

G

BH001

05

>PI<

FP-298-

LND001 LND002LND003 LND004LND005 LND006LND007 LND008LND009 LND010LND011 LND012LND013 LND014LND015

LND021LND022LND023LND024LND025LND026LND027LND028LND029LND030LND031LND032LND033LND034

1

15

1

14

FP-298 FLEXIBLE BOARD

1-867-902- 1105

1-86

7-1

867

186

7 1

867

186

77-7-77-77777 -2922292

>PI<

226

2728125

CN001

D001D002D003

LND0

01LN

D002

LND0

03LN

D004

LND0

05LN

D006

LND0

07LN

D008

LND0

09LN

D010

LND0

11LN

D012

LND0

13LN

D014

LND0

15LN

D016

LND0

17LN

D018

LND0

19LN

D020

LND0

21LN

D022

LND0

23LN

D024

LND0

25LN

D026

LND0

27LN

D028

LND0

29LN

D030

LND0

31LN

D032

LND0

33

LND040

R002

+

–

2 3

1

2 3

1

BT001

133


1-867-907- 11

BT001BATTERY,

LITHIUM SECONDARY

Note: CN001 (multi connector) is not supplied, but this is included in JK-292 flexible complete board.

(MULTI CONNECTOR)05

4-45DSC-T5_L2

4-4. WAVEFORMS



CD-587

1

Q003 B REC

1.1 Vp-p

H

4-46DSC-T5_L2

Waveforms of the SY-134 board are not shown.Page 4-46 is not shown.

4-47DSC-T5_L2

Mounted parts location of the SY-134 board is not shown.Page 4-47 is not shown.

4-48EDSC-T5_L2

4-5. MOUNTED PARTS LOCATION no mark : side A

* mark : side B


R001 F-2R002 E-2R003 E-1R004 F-1R005 F-1R006 D-1R007 C-1R008 C-1

S001 F-2S002 E-2S003 E-2S004 E-1S005 E-2S006 D-1S007 F-1S008 E-1S009 C-1S010 C-2

SW-455 FLEXIBLE

SW-455

NOTENOTE

DSC-T5_L2

LinkLink

5. REPAIR PARTS LIST

LinkLink ELECTRICAL PARTS LISTELECTRICAL PARTS LIST

EXPLODED VIEWSEXPLODED VIEWS

ACCESSORIESACCESSORIES

NOTE: Characters A to Z of the electrical parts list indicate location of exploded views in which the desired part is shown.

A B C

CABINET SECTION BT BLOCK SECTIONMAIN SECTION



ST-126 BOARD

JK-292 FLEXIBLE BOARD SW-455 BOARD

B

C

B

C B

5. REPAIR PARTS LIST

5-1

5. REPAIR PARTS LIST5. REPAIR PARTS LIST

The components identified by mark 0 ordotted line with mark 0 are critical for safety.Replace only with part number specified.

Les composants identifiés par une marque0 sont critiques pour la sécurité.Ne les remplacer que par une pièce portantle numéro spécifié.

NOTE:• -XX, -X mean standardized parts, so they may have some differences from

the original one.• Items marked “*” are not stocked since they are seldom required for routine

service. Some delay should be anticipated when ordering these items.• The mechanical parts with no reference number in the exploded views are not

supplied.• Due to standardization, replacements in the parts list may be different from

the parts specified in the diagrams or the components used on the set.• CAPACITORS:

uF: µF• COILS

uH: µH• RESISTORS

All resistors are in ohms.METAL: metal-film resistorMETAL OXIDE: Metal Oxide-film resistorF: nonflammable

• SEMICONDUCTORSIn each case, u: µ, for example:uA...: µA... , uPA... , µPA... ,uPB... , µPB... , µPC... , µPC... ,uPD..., µPD...

• AbbreviationAR : Argentine modelAUS : Australian modelBR : Brazilian modelCH : Chinese modelCND : Canadian modelEE : East European modelHK : Hong Kong modelJ : Japanese modelJE : Tourist modelKR : Korea modelNE : North European model

DSC-T5_L2

• Language that can be selected about SY-134 board

When indicating parts by reference number,please include the board name.

Are

a

Japa

nese

Eng

lish

Fren

ch

Ger

man

Spa

nish

Italia

n

Por

tuga

l

Sim

plifi

edC

hine

se

Trad

ition

alC

hine

se

Ara

bic

Dut

ch

Rus

sian

Sw

edis

h

Kor

ean

Nor

weg

ian

Dan

ish

Fin

nish

Pol

ish

Hun

garia

n

Cze

ch

Per

sian

Tha

i

GP1 J z

US

GP2CND

z z z z z zAUSVietnam

GP3AEP

z z z z z z z z z z z z z z zUK

EARBRTW

z z z z z z z z zGP4JEHKCHKR

5-2


DSC-T5_L2

5-1-1. CABINET SECTION

Ref. No. Part No. Description Ref. No. Part No. Description

1 2-635-591-11 SCREW (M1.4), NEW TRUSTAR P22 X-2067-184-1 CABINET (FRONT) ASSY (SILVER)2 X-2067-185-1 CABINET (FRONT) ASSY (B) (BLACK)2 X-2067-186-1 CABINET (FRONT) ASSY (R) (RED)2 X-2067-187-1 CABINET (FRONT) ASSY (N) (GOLD)

3 2-635-591-01 SCREW (M1.4), NEW TRUSTAR P24 1-479-435-11 SWITCH BLOCK, CONTROL (RL51860)5 2-637-497-01 BUTTON, FUNCTION

* 6 2-637-511-01 SHEET, BLIND7 2-637-498-01 SHEET (1), FUNCTION ADHESIVE

8 2-637-499-01 BRACKET, STRAP

9 2-637-501-01 HOLDER, STRAP10 2-637-496-01 CABINET (REAR) (SILVER)10 2-637-496-11 CABINET (REAR) (BLACK)10 2-637-496-21 CABINET (REAR) (RED)10 2-637-496-31 CABINET (REAR) (GOLD)

11 2-637-509-01 COVER, LCD* 12 2-637-495-01 SHEET, STROBOSCOPE INSULATING* 13 2-637-505-01 COVER, MULTI

14 2-637-504-01 BOTTOM, CABINET* 15 2-637-508-01 RADIATION SHEET, F

* 16 2-653-866-01 SHEET (A), CABINET (UPPER)

5-1. EXPLODED VIEWS

1

2

3

3

3

3

4

5

7

8

9

10

11

12

16

615

13

14

Main section (See page 5-3.)

5-3


DSC-T5_L2

5-1-2. MAIN SECTION


51 3-078-889-21 SCREW (M1.7)52 A-1142-659-A SY-134 BOARD, COMPLETE (SERVICE) (GP1)52 A-1146-566-A SY-134 BOARD, COMPLETE (SERVICE) (GP2)52 A-1146-567-A SY-134 BOARD, COMPLETE (SERVICE) (GP3)52 A-1146-568-A SY-134 BOARD, COMPLETE (SERVICE) (GP4)

53 1-867-902-11 FP-298 FLEXIBLE BOARD054 A-1129-574-A ST-126 BOARD, COMPLETE055 1-478-972-11 FLASH UNIT

56 A-1129-577-A SW-455 FLEXIBLE BOARD, COMPLETE (Note2)

ns: not supplied

57 A-1118-808-A LSV-1040A (SERVICE)58 1-788-249-21 OPTICALFILTER BLOCK (OFB-02-22)59 3-086-156-11 SCREW B1.260 2-637-503-01 INSULATING SHEET, CCD62 A-1129-513-A CCD BLOCK ASSY (including CD-587 flexible

board and IC002 (CCD imager)) (Note1)

* 63 2-637-510-01 SHEET, SP INSULATINGSP901 1-825-983-21 SPEAKER (1.62CM) (Note2)

Note1: Be sure to read “Precuations for Replacement of Imager”on page 4-5 when changing the imager.

51

52

53

54

55

56(Note2)

57

58

59

60

BT block section(See page 5-4.)

62(including CD-587 flexible board and IC002 (CCD imager)) (Note1)

ns

ns

SP901(Note2)

ns

63


* Refer to the table of page 5-1 about language of SY-134 board.

Ver 1.2 2005.10

Note2: Refer to page 2-1 “Note for installation of speaker(SP901) and SW-455 flexible board”, when change thespeaker (SP901)

5-4


DSC-T5_L2


101 3-080-222-21 SCREW (M1.7), TAPPING, P2* 102 2-637-492-01 FRAME, TERMINAL RETAINER

103 A-1129-578-A BT-028 FLEXIBLE BOARD, COMPLETE104 A-1129-576-A JK-292 FLEXIBLE BOARD, COMPLETE

(including CN001 (multi connector) )105 2-637-480-01 LID, BT (Note)

106 X-2067-188-1 HOLDER ASSY, BT* 107 2-637-491-01 CUSHION, LENS

5-1-3. BT BLOCK SECTION

* 108 2-637-494-01 SHEET, PANEL (FP) PROTECTION* 109 2-637-493-01 FRAME, MAIN

110 2-637-490-01 SCREW, TRIPOD111 3-078-889-21 SCREW (M1.7)

0BT001 1-756-566-11 BATTERY, LITHIUM SECONDARY

D901 1-479-381-11 BLOCK, LIGHT GUIDE PLATE (2.5)LCD901 A-1146-639-A SERVICE, LCD BLOCK ASSY (SERVICE)

ns: not supplied

CAUTIONDanger of explosion if battery is incorrectly replaced.Replace only with the same or equivalent type.


!

! BT001(BATTERY, LITHIUM SECONDARY)Board on the mount position (See page 4-42).

101

102

103

104

105(Note)

106

107

108

109

110101

111

ns

BT001

LCD901

D901

111

Note: Be sure to read “2-1. DISASSEMBLY (Howto disassemble BT lid)” on page 2-3.

5-5

Ref. No. Part No. Description Ref. No. Part No. Description5-2. ELECTRICAL PARTS LIST

DSC-T5_L2

BT-028 CD-587 JK-292 ST-126 SW-455

A-1129-578-A BT-028 FLEXIBLE BOARD, COMPLETE*******************************

< BATTERY TERMINAL >

0BH001 1-780-196-11 TERMINAL BOARD, BATTERY

A-1129-513-A CCD BLOCK ASSY(Not supplied) CD-587 FLEXIBLE BOARD, COMPLETE

********************************(CCD block assy is including CD-587 flexible board

and IC002 (CCD imager))

< CAPACITOR >

C003 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16VC004 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16VC005 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V

< IC >

IC002 (Not supplied) ICX495CQZ-13 (Note)

< TRANSISTOR >

Q001 6-550-119-01 TRANSISTOR DTC144EMT2LQ002 6-550-119-01 TRANSISTOR DTC144EMT2LQ003 6-550-885-01 TRANSISTOR 2SC39320S2S0

< RESISTOR >

R002 1-218-960-11 RES-CHIP 3.9K 5% 1/16WR003 1-218-969-11 RES-CHIP 22K 5% 1/16WR004 1-218-955-11 RES-CHIP 1.5K 5% 1/16WR005 1-218-954-11 RES-CHIP 1.2K 5% 1/16WR006 1-218-990-81 SHORT CHIP 0

A-1129-576-A JK-292 FLEXIBLE BOARD, COMPLETE*******************************

(This flexible complete board is includingCN001 (multi connector))

< BATTERY >

0BT001 1-756-566-11 BATTERY, LITHIUM SECONDARY

< CONNECTOR >

CN001 (Not supplied) CONNECTOR, MULTIPLE (SOCKET)

< DIODE >

D001 6-500-776-01 DIODE MAZW068H0LS0D002 6-500-776-01 DIODE MAZW068H0LS0D003 8-719-056-54 DIODE MAZS068008SO

< RESISTOR >

R002 1-216-803-11 METAL CHIP 33 5% 1/10W

0 A-1129-574-A ST-126 BOARD, COMPLETE***********************

0 1-478-972-11 FLASH UNIT

< CAPACITOR >

C001 1-165-908-11 CERAMIC CHIP 1uF 10% 10VC002 1-100-611-91 CERAMIC CHIP 22uF 20% 6.3VC003 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V

0C005 1-112-675-11 CAP, ELECT 85uF 315VC006 1-100-758-11 CERAMIC CHIP 0.047uF 10% 250V

< CONNECTOR >

* CN001 1-816-654-51 FFC/FPC CONNECTOR (LIF) 6P* CN002 1-819-551-51 CONNECTOR, FFC/FPC (ZIF) 14P

< DIODE >

0D001 6-501-096-01 DIODE CRF02 (TE85R)* D003 6-501-313-01 DIODE TLOH9203 (SONY)

(SELF TIMER/AF ILLUMINATOR)

< IC >

IC001 6-707-554-01 IC TPS65552DGQR

< COIL >

* L001 1-400-820-11 INDUCTOR 2.2uH

< TRANSISTOR >

0Q001 6-550-656-01 TRANSISTOR CY25BAJ-8F-T23

< RESISTOR >

R001 1-216-803-11 METAL CHIP 33 5% 1/10WR002 1-216-857-11 METAL CHIP 1M 5% 1/10WR003 1-216-121-11 RES-CHIP 1M 5% 1/10WR004 1-216-864-11 SHORT CHIP 0

< TRANSFORMER >

0T001 1-443-648-21 DC-DC CONVERTER TRANSFORMER

A-1129-577-A SW-455 FLEXIBLE BOARD, COMPLETE********************************

SP901 1-825-983-21 LOUDSPEAKER (1.62CM)

< RESISTOR >

R001 1-216-822-11 METAL CHIP 1.2K 5% 1/10WR002 1-216-823-11 METAL CHIP 1.5K 5% 1/10WR003 1-216-827-11 METAL CHIP 3.3K 5% 1/10WR004 1-218-867-11 METAL CHIP 6.8K 0.5% 1/10WR005 1-216-822-11 METAL CHIP 1.2K 5% 1/10W

R006 1-216-823-11 METAL CHIP 1.5K 5% 1/10WR007 1-216-827-11 METAL CHIP 3.3K 5% 1/10WR008 1-218-867-11 METAL CHIP 6.8K 0.5% 1/10W

< SWITCH >

S001 1-786-157-11 SWITCH, TACTILE (F (SELF TIMER))S002 1-786-157-11 SWITCH, TACTILE (G(MACRO))S003 1-786-157-11 SWITCH, TACTILE (f (FLASH))S004 1-786-157-11 SWITCH, TACTILE (g (REVIEW))

Note: Be sure to read “Precautions for Replacement ofImager” on page 4-5 when changing the imager.



5-6DSC-T5_L2

S005 1-786-157-11 SWITCH, TACTILE (a (SET))

S006 1-786-157-11 SWITCH, TACTILE (SCREEN DISPLAY ON/OFF)S007 1-786-157-11 SWITCH, TACTILE (IMAGE SIZE/DELETE)S008 1-786-157-11 SWITCH, TACTILE (MENU)S009 1-786-157-11 SWITCH, TACTILE (W (ZOOM))S010 1-786-157-11 SWITCH, TACTILE (T (ZOOM))

SW-455

Electrical parts list of the SY-134 board isnot shown.Pages 5-7 to 5-10 are not shown.

5-11DSC-T5_L2

Checking supplied accessories.


USB, A/V, DC IN cablefor multi-use terminal (1)1-830-848-11

CD-ROM(Cyber-shot application software)2-650-869-01

Power cord (mains lead) (1)0 1-776-985-11 (KR)0 1-782-476-51 (CH)0 1-783-374-11 (UK, HK)0 1-790-732-71 (JE)0 1-823-946-12 (AEP, E)0 1-827-945-12 (AUS)

Conversion adaptor (1)1-569-008-21 (E)

Wrist strap (1)2-050-981-01

Battery charger BC-CS3 (1)0 1-479-140-11 (J)0 1-479-140-21 (US, CND)0 1-479-140-31 (EXCEPT US, CND, J)

Conversion adaptor (1)1-573-856-12 (JE)

Rechargeable battery packNP-FT1 (1)(not supplied)

Battery case (1)(not supplied)

Ver 1.2 2005.10

5-12EDSC-T5_L2

Checking supplied accessories.

Other accessories2-635-477-01 INSTRUCTION (READ THIS FIRST)

(JAPANESE) (J)2-635-477-11 INSTRUCTION (READ THIS FIRST)

(ENGLISH) (AEP, UK, E, HK, AUS, JE)2-635-477-21 INSTRUCTION (READ THIS FIRST)

(FRENCH, ITALIAN) (AEP)2-635-477-31 INSTRUCTION (READ THIS FIRST)

(SPANISH, PORTUGUESE) (AEP, E, JE)2-635-477-41 INSTRUCTION (READ THIS FIRST)

(GERMAN, DUTCH) (AEP)

2-635-477-51 INSTRUCTION (READ THIS FIRST)(TRADITIONAL CHINESE,

SIMPLIFIED CHINESE) (E, HK, CH, JE)2-635-477-61 INSTRUCTION (READ THIS FIRST)

(RUSSIAN) (AEP)2-635-477-71 INSTRUCTION (READ THIS FIRST) (ARABIC,

PERSIAN) (E)2-635-477-81 INSTRUCTION (READ THIS FIRST)

(KOREAN) (KR, JE)2-635-477-91 INSTRUCTION (READ THIS FIRST) (CZECH,

POLISH) (AEP)

2-635-481-11 INSTRUCTION (READ THIS FIRST)(HUNGARIAN, SLOVAK) (AEP)

2-635-481-21 INSTRUCTION (READ THIS FIRST)(SWEDISH, FINNISH) (AEP)

2-635-481-31 INSTRUCTION (READ THIS FIRST)(NORWEGIAN, DANISH) (AEP)

2-635-482-01 INSTRUCTION (USER’S GUIDE) (JAPANESE)(J)

2-635-482-11 INSTRUCTION (USER’S GUIDE)(ENGLISH) (EXCEPT KR, J)

2-635-482-21 INSTRUCTION (USER’S GUIDE)(FRENCH, ITALIAN) (CND, AEP)

2-635-482-31 INSTRUCTION (USER’S GUIDE) (SPANISH,PORTUGUESE) (AEP, E, JE)

2-635-482-41 INSTRUCTION (USER’S GUIDE) (GERMAN,DUTCH) (AEP)

2-635-482-51 INSTRUCTION (USER’S GUIDE)(TRADITIONAL CHINESE,

SIMPLIFIED CHINESE) (E, HK, CH, JE)2-635-482-61 INSTRUCTION (USER’S GUIDE) (RUSSIAN)

(AEP)

2-635-482-71 INSTRUCTION (USER’S GUIDE) (ARABIC,PERSIAN) (E)

2-635-482-81 INSTRUCTION (USER’S GUIDE) (KOREAN)(KR, JE)

2-635-482-91 INSTRUCTION (USER’S GUIDE) (POLISH,CZECH) (AEP)

2-635-483-11 INSTRUCTION (USER’S GUIDE)(HUNGARIAN, SLOVAK) (AEP)

2-635-483-21 INSTRUCTION (USER’S GUIDE) (SWEDISH,FINNISH) (AEP)

2-635-483-31 INSTRUCTION (USER’S GUIDE)(NORWEGIAN, DANISH) (AEP)

2-638-045-11 INSTRUCTION (READ THIS FIRST)(ENGLISH) (US)

2-638-045-21 INSTRUCTION (READ THIS FIRST)(FRENCH) (CND)

SERVICE MANUALLEVEL 2

Ver 1.1 2005.09

Sony EMCS Co.9-876-887-83

2005I0500-1© 2005.9

Published by DI Technical Support Department

SUPPLEMENT-1File this supplement with the service manual.

(PV05-051)

• Addition of Brazilian Model

DSC-T5_L2

DSC-T5US Model

Canadian ModelAEP Model

UK ModelE Model

Australian ModelHong Kong Model

Chinese ModelKorea Model

Brazilian ModelJapanese Model

Tourist Model

The differences with other area models are only accessories.

Checking supplied accessories.&: Points add portion.

2-635-482-11 INSTRUCTION (USER’S GUIDE)(ENGLISH) (EXCEPT KR, J)

Page Former New

2-635-482-11 INSTRUCTION (USER’S GUIDE)(ENGLISH) (EXCEPT KR, BR, J)

5-11

5-12

)

Battery charger BC-CS3 (1)0 1-479-140-11 (J)0 1-479-140-21 (US, CND)0 1-479-140-31 (EXCEPT US, CND, J)

Battery charger BC-CS3 (1)0 1-479-140-11 (J)0 1-479-140-21 (US, CND)0 1-479-140-31 (EXCEPT US, CND, BR, J)

)

[Description of main button functions on toolbar of the Adobe Acrobat Reader Ver5.0 (for Windows)]

Printing a text1. Click the Print button .2. Specify a printer, print range, number of copies, and other op-

tions, and then click [OK].

Application of printing:To set a range to be printed within a page, select the graphic

selection tool and drag on the page to enclose a range tobe printed, and then click the Print button.

Finding a text1. Click the Find button .2. Enter a character string to be found into a text box, and click

the [Find]. (Specify the find options as necessary)

Application to the Service Manual:To execute “find” from current page toward the previous pages,select the check box “Find Backward” and then click the“Find”.

3. Open the find dialog box again, and click the [Find Again] andyou can find the matched character strings displayed next.(Character strings entered previously are displayed as they arein the text box.)

Application to the Service Manual:The parts on the drawing pages (block diagrams, circuit dia-grams, printed circuit boards) and parts list pages in a textcan be found using this find function. For example, find aRef. No. of IC on the block diagram, and click the [Find Again]continuously, so that you can move to the Ref. No. of IC onthe circuit diagram or printed circuit board diagram succes-sively.Note: The find function may not be applied to the Service

Manual depending on the date of issue.

Switching a page• To move to the first page, click the .

• To move to the last page, click the .

• To move to the previous page, click the .

• To move to the next page, click the .

Reversing the screens displayed once• To reverse the previous screens (operation) one by one, click

the .

• To advance the reversed screens (operation) one by one, click

the .

Application to the Service Manual:This function allows you to go and back between circuit dia-gram and printed circuit board diagram, and accordingly itwill be convenient for the voltage check.

Moving with link

1. Select either palm tool , zoom tool , text selection tool

, or graphic selection tool .2. Place the pointer in the position in a text where the link exists

(such as a button on cover and the table of contents page, orblue characters on the removal flowchart page or drawingpage), and the pointer will change to the forefinger form .

3. Then, click the link. (You will go to the link destination.)

Moving with bookmark:Click an item (text) on the bookmark pallet, and you can moveto the link destination. Also, clicking can display thehidden items.(To go back to original state, click )

Zooming or rotating the screen display“Zoom in/out”• Click the triangle button in the zoom control box to select the

display magnification. Or, you may click or for zoom-

ing in or out.

“Rotate”• Click rotate tool , and the page then rotates 90 degrees each.

Application to the Service Manual:The printed circuit board diagram you see now can be changedto the same direction as the set.

Toolbar

Revision History

Reverse

DSC-T5_L2

Ver.

1.0

1.1

1.2

Date

2005.07

2005.09

2005.10

History

Official Release

Supplement-1(S1 PV05-051)

Correction-1(C1)

Contents

—

• Addition of Brazilian Model

• Correction of Repair parts• Addition of Note for Installation of Speaker

(SP901) and SW-455 Flexible BoardS.M. correction: Page 2-1, Page 2-4,

Page 5-3, Page 5-11

S.M. Rev.issued

—

No

Yes

987688733.pdf

Documents

DSC-T5 · 2013-07-25 · (including NP-FT1 battery pack and wrist strap, etc.) Microphone Electret condenser microphone Speaker Dynamic speaker Exif Print Compatible PRINT Image Matching