Digital Lab Manual for CSE & IT - Anna Univeristy Chennai Syllabus - 2012

1

TIRUCHENGODE – 637215

NAME :

ROLL NO :

CLASS / SEM : II B.E -CSE / III SEM

SECTION :

SUBJECT CODE : CS 2207

SUBJECT NAME : DIGITAL LABORATORY

LABORATORY MANUAL

Prepared by

P.SUNDARAVADIVEL., M.E.,

ASSISTANT PROFESSOR

2

K.S.R. COLLEGE OF ENGINEERING

TIRUCHENGODE - 637215

Register No

Certified that this is the bonafide record of

work done by Selvan / Selvi ………………………………………………..………………..

of the ………….…………….Semester…………………………………………………………………

branch during the Year…………………… in the

………………………………….................Laboratory.

Staff in Charge Head of the Department ---------------------------------------------------------------------------------- Submitted for the University Practical Examination on…………………………... Internal Examiner External Examiner

3

LABORATORY REGULATIONS AND SAFETY RULES

The following Regulations and Safety Rules must be observed in all concerned

laboratory location.

It is the duty of all concerned who use any electronics laboratory to take

all reasonable steps to safeguard the HEALTH and SAFETY of themselves

and all other users and visitors.

Be sure that all equipment is properly working before using them for

laboratory exercises. Any defective equipment must be reported

immediately to the Lab. Instructors or Lab. Technical Staff.

Students are allowed to use only the equipment provided in the

experiment manual.

Power supply terminals connected to any circuit are only energized with

the presence of the Instructor or Lab. Staff.

Avoid any part of your body to be connected to the energized circuit and

ground.

Switch off the equipment and disconnect the power supplies from the

circuit before leaving the laboratory.

Observe cleanliness and proper laboratory house keeping of the

equipment and other related accessories.

Make sure that the last connection to be made in your circuit is the power

supply and first thing to be disconnected is also the power supply.

Equipment should not be removed, transferred to any location without

permission from the laboratory staff.

Students are not allowed to use any equipment without proper orientation

and actual hands on equipment operation.

4

EXTRACT OF ANNA UNIVERSITY SYLLABUS

DIGITAL LABORATORY – COMPUTER SCIENCE & ENGINEERING LIST OF EXPERIMENTS

1. Verification of Boolean theorems using digital logic gates

2. Design and implementation of combinational circuits using basic gates for

arbitrary functions, code converters, etc.

3. Design and implementation of 4-bit binary adder / subtractor using basic

gates and MSI devices

4. Design and implementation of parity generator / checker using basic gates

and MSI devices

5. Design and implementation of magnitude comparator

6. Design and implementation of application using multiplexers/Demultiplexers

7. Design of RS and JK flip flops Using NAND gates

8. Design and implementation of Shift registers

9. Design and implementation of Synchronous counters

10. Design and implementation of Asynchronous counters

11. Simulation of combinational circuits using Hardware Description Language

(VHDL/ Verilog HDL software required)

12. Simulation of sequential circuits using HDL (VHDL/ Verilog HDL software

required)

Lab in- Charge

5

INDEX

S.NO DATE EXPERIMENT NAME PAGE NO MARKS SIGN

I CYCLE EXPERIMENTS

1 Verification of Boolean theorems using digital

logic gates

2

Design and implementation of combinational

circuits using basic gates for arbitrary

functions, code converters, etc.

3

Design and implementation of 4-bit binary

adder / subtractor using basic gates and MSI

devices

4 Design and implementation of parity generator

/ checker using basic gates and MSI devices

5 Design and implementation of magnitude

comparator

6 Design and implementation of application

using multiplexers/Demultiplexers

II CYCLE EXPERIMENTS

7 Design of RS and JK flip flops Using NAND

gates

8 Design and implementation of Shift registers

9 Design and implementation of Synchronous

counters

10 Design and implementation of Asynchronous

counters

11

Simulation of combinational circuits using

Hardware Description Language


12 Simulation of sequential circuits using HDL


Staff In-Charge Total

Average

6

A “Bread-Board” is used in a laboratory for constructing the different circuits

and testing them. This is very useful since here; we do not have to solder the different

components. Soldering, as you know can be very time consuming. Further, we can reuse

the components again and again, since they are not cut and soldered. Let us learn below

how we can use the breadboard for such applications. The breadboard contains a

number of metal clips aligned beneath the array of holes so that when we insert the lead

of a component (say, resistor) inside a hole, the clip grips the lead tightly. Observe the

figure. Fig(a) shows a metal clip before a component inserted, while Fig(b) shows after

the lead inserted. Fig(c) shows a clip which is beneath an array of 5-holes. All the five

holes correspond to one node since all of them are connected together electrically by the

metal clip. That means up to 5 wires can be connected to this single node.

7

8

Pin Details of Digital Logic Gates:

9

Postulates and Theorems of Boolean algebra:

S.

No Postulate/Theorem Duality Remarks

1. X + 0 = X X.1 = X -

2. X + X’ = 1 X.X’ = 0 -

3. X + X = X X.X = X -

4. X + 1 = 1 X.0 = 0 -

5. (X’)’ = X - Involution

6. X + Y = Y + X X.Y = Y.X Commutative

7. X + (Y + Z) = (X + Y) + Z X.(Y.Z) = (X.Y).Z Associative

8. X.(Y + Z) = X.Y + X.Z X + (Y.Z) = (X + Y)(X + Z) Distributive

9. (X + Y)’ = X’Y’ (XY)’ = X’ + Y’ DeMorgan’s Theorem

10. X + XY = X X.(X + Y) = X Absorption

Bit Grouping:

Bit - A single, bivalent unit of binary.

Equivalent to a decimal "digit."

Crumb, Tydbit, or Tayste - Two bits.

Nibble or Nybble - Four bits.

Nickle - Five bits.

Byte - Eight bits.

Deckle - Ten bits.

Playte - Sixteen bits.

Dynner - Thirty-two bits.

Word - (system dependent).

Arithmetic Notations:

Augend + Addend = Sum

Minuend – Subtrahend = Difference

Multiplicand X Multiplier = Product

Dividend / Divisor = Quotient

10

Verification of Logic Gates:

11

EXP. NO : 1

DATE :

VERIFICATION OF BOOLEAN THEOREMS USING DIGITAL LOGIC GATES

----------------------------------------------------------------------------------------

Aim:

To verify the truth table of basic Boolean algebric laws by using logic gates.

Components Required:

S.NO COMPONENTS RANGE QUANTITY 1 Digital IC trainer kit - 1

2 IC

7400 1 7402 1 7404 1 7408 1 7432 1 7486 1

3 Bread board - 1 4 Connecting wires - As required

Theory:

Demorgan’s Theorems

First Theorem:

It states that the complement of a product is equal to the sum of the

complements.

(AB)′ =A′ +B′

Second Theorem:

It states that the complement of a sum is equal to the product of the

complements.

(A+B)′ =A′.B′

Boolean Laws:

Boolean algebra is a mathematical system consisting of a set of two or more

distinct elements, two binary operators denoted by the symbols (+) and (.) and one

unary operator denoted by the symbol either bar (-) or prime (‘). They satisfy the

commutative, associative, distributive and absorption properties of the Boolean algebra.

Commutative Property:

Boolean addition is commutative, given by

A+B=B+A

Boolean algebra is also commutative over multiplication, given by

A.B=B.A

12

De-Morgan’s Theorem: 1

De-Morgan’s Theorem: 2

13

Associative Property:

The associative property of addition is given by

A+ (B+C) = (A+B) +C

The associative law of multiplication is given by

A. (B.C) = (A.B).C

Distributive Property:

The Boolean addition is distributive over Boolean multiplication, given by

A+BC = (A+B) (A+C)

Boolean multiplication is also distributive over Boolean addition given by

A. (B+C) = A.B+A.C

Realization of circuits for Boolean expression after simplification:

A binary variable can take the value of ‘0’ or ‘1’. A Boolean function is an

expression formed with binary operator OR, AND and a unary operator NOT, parenthesis

function can be 0 or 1.

For example, consider the function

The prime implicants are found by using the elimination of complementary function. The

circuit diagram for the function is drawn using AND.OR and NOT gates. The output for

the corresponding input of A1, A0, B1, BO is calculated and the truth table is drawn.

Procedure:

1. Test the individual ICs with its specified verification table for proper working.

2. Connections are made as per the circuit/logic diagram.

3. Make sure that the ICs are enabled by giving the suitable Vcc and ground

connections.

4. Apply the logic inputs to the appropriate terminals of the ICs.

5. Observe the logic output for the inputs applied.

6. Verify the observed logic output with the verification/truth table given.

14

Commutative Law:

Truth Table:

Input Output

A B A+B B+A

0 0 0 0

0 1 1 1

1 0 1 1

1 1 1 1

Associative Law:

Truth Table:

Input Output

A B C A+B (A+B)+C B+C A+(B+C)

0 0 0 0 0 0 0

0 0 1 0 1 1 1

0 1 0 1 1 1 1

0 1 1 1 1 1 1

1 0 0 1 1 0 1

1 0 1 1 1 1 1

1 1 0 1 1 1 1

1 1 1 1 1 1 1

15

16

Distributive Law:

Truth Table:

Input Output

A B C B+C A.(B+C) A.B A.C A.B+A.C

0 0 0 0 0 0 0 0

0 0 1 1 0 0 0 0

0 1 0 1 0 0 0 0

0 1 1 1 0 0 0 0

1 0 0 0 0 0 0 0

1 0 1 1 1 0 1 1

1 1 0 1 1 1 0 1

1 1 1 1 1 1 1 1

17

18

19

Description Max.

Marks

Marks

Secured

Preparation 30

Performance 40

Viva Voce 10

Record 20

Total 100

Staff Signature

Result:

Thus the verification of Boolean laws and theorems using digital logic gates were

performed.

20

Truth Table for Arbitrary Function:

Input Output

A1 A0 B1 B0 F

0 0 0 0 0

0 0 0 1 0

0 0 1 0 0

0 0 1 1 0

0 1 0 0 1

0 1 0 1 0

0 1 1 0 0

0 1 1 1 0

1 0 0 0 1

1 0 0 1 1

1 0 1 0 0

1 0 1 1 0

1 1 0 0 1

1 1 0 1 1

1 1 1 0 1

1 1 1 1 0

Realization of simplified Boolean

expression using K-Map:

21

EXP. NO: 2

DATE :

DESIGN AND IMPLEMENTATION OF COMBINATIONAL CIRCUITS USING BASIC

GATES FOR ARBITRARY FUNCTIONS AND CODE CONVERTERS

---------------------------------------------------------------------------------------------------

Aim:

To design and implement a combinational circuit to convert gray code to Binary

and BCD to Excess-3 – vice versa.


S.NO COMPONENTS RANGE QUANTITY 1 Digital IC Trainer kit - 1

2 IC

7404 1 7408 2 7432 1 7486 1

3 Connecting wires - As required 4 Bread board - 1

Theory:

Binary to Gray – Vice versa:

The binary coded decimal (BCD) code is one of the early computer codes. Each

decimal digit is independently converted to a 4 bit binary number. A binary code will

have some unassigned bit combinations if the number of elements in the set is not a

multiple power of 2. The 10 decimal digits form such a set. A binary code that

distinguishes among 10 elements must contain at least four bits, but 6 out of the 16

possible combinations remain unassigned. Different binary codes can be obtained by

arranging four bits in 10 distinct combinations. The code most commonly used for the

decimal digits is the straight binary assignment. This is called binary coded decimal.

The gray code is used in applications where the normal sequence of binary

numbers may produce an error or ambiguity during the transition from one number to

the next. If binary numbers are used, a change from 0111 to 1100 may produce an

intermediate erroneous number 1001 if the rightmost bit takes longer to change in value

than the other three bits. The gray code eliminates this problem since only one bit

changes in value during any transition between two numbers.

22

Truth Table (Binary to Gray):

Binary (Input) Gray (Output)

B3 B2 B1 B0 G3 G2 G1 G0

0 0 0 0 0 0 0 0

0 0 0 1 0 0 0 1

0 0 1 0 0 0 1 1

0 0 1 1 0 0 1 0

0 1 0 0 0 1 1 0

0 1 0 1 0 1 1 1

0 1 1 0 0 1 0 1

0 1 1 1 0 1 0 0

1 0 0 0 1 1 0 0

1 0 0 1 1 1 0 1

1 0 1 0 1 1 1 1

1 0 1 1 1 1 1 0

1 1 0 0 1 0 1 0

1 1 0 1 1 0 1 1

1 1 1 0 1 0 0 1

1 1 1 1 1 0 0 0

23

BCD to Excess 3 – Vice versa:

Excess 3 code is a modified form of a BCD number. The excess 3 code can be

derived from the natural BCD code by adding 3 to each coded number. For example,

decimal 6 can be represented in BCD as 0110. Now adding 3 to the given number yield

equivalent excess 3 code i.e., 6 + 3 = 9 0110 + 0011 = 1001. Thus for the entire

sequence of BCD value (i.e., 0 to 9) excess 3 equivalent table should be made so that

the realization of Boolean expression for the circuit implementation is feasible. In the

reverse process of designing a code converter from excess 3 to BCD the same procedure

is followed. Here are the general steps to be followed while going for a code converter

design,

– start with the specification of the circuit to be designed.

– Identify the inputs and outputs

– Derive truth table

– Obtain simplified Boolean equations

– Draw the logic diagram

– Check the design to verify correctness with the truth/verification table.

24

Logic Diagram:

Pin Diagram:

25

Procedure:




connections.




26

Truth Table (Gray to Binary):

Gray (Input) Binary (Output) G3 G2 G1 G0 B3 B2 B1 B0 0 0 0 0 0 0 0 0 0 0 0 1 0 0 0 1 0 0 1 0 0 0 1 1 0 0 1 1 0 0 1 0 0 1 0 0 0 1 1 1 0 1 0 1 0 1 1 0 0 1 1 0 0 1 0 0 0 1 1 1 0 1 0 1 1 0 0 0 1 1 1 1 1 0 0 1 1 1 1 0 1 0 1 0 1 1 0 0 1 0 1 1 1 1 0 1 1 1 0 0 1 0 0 0 1 1 0 1 1 0 0 1 1 1 1 0 1 0 1 1 1 1 1 1 1 0 1 0

27

28

Logic Diagram:

Truth Table:

Decimal Value

BCD Input Excess 3 output

A B C D W X Y z

0 0 0 0 0 0 0 1 1

1 0 0 0 1 0 1 0 0

2 0 0 1 0 0 1 0 1

3 0 0 1 1 0 1 1 0

4 0 1 0 0 0 1 1 1

5 0 1 0 1 1 0 0 0

6 0 1 1 0 1 0 0 1

7 0 1 1 1 1 0 1 0

8 1 0 0 0 1 0 1 1

9 1 0 0 1 1 1 0 0

29

30

Realization of Boolean Expression for BCD to Excess 3 Converter:

Circuit Diagram:

31

32

Truth Table:

Decimal Value

Excess 3 Input BCD Output

W X Y z A B C D

0 0 0 1 1 0 0 0 0

1 0 1 0 0 0 0 0 1

2 0 1 0 1 0 0 1 0

3 0 1 1 0 0 0 1 1

4 0 1 1 1 0 1 0 0

5 1 0 0 0 0 1 0 1

6 1 0 0 1 0 1 1 0

7 1 0 1 0 0 1 1 1

8 1 0 1 1 1 0 0 0

9 1 1 0 0 1 0 0 1

Realization of Boolean Expression for Excess 3 to BCD Converter:

33

34

Circuit Diagram:

35

Description Max.

Marks

Marks

Secured

Preparation 30

Performance 40

Viva Voce 10

Record 20

Total 100

Staff Signature

Result:

Thus the combinational circuit for an arbitrary function, code converter using logic

gates was designed, implemented and tested its performance with truth table.

36

Logic Diagram:

Pin Diagram:

37

EXP. NO : 3

DATE :

DESIGN AND IMPLEMENTATION OF 4 BIT BINARY ADDER / SUBTRACTOR

USING MSI DEVICES

------------------------------------------------------------------------------------------------

Aim:

To design and implement a four bit binary adder / subtractor using MSI devices.

Apparatus Required:

S.NO COMPONENTS RANGE QUANTITY

1 IC trainer kit - 1

2 IC’s 7483 1

7486 1

3 Connecting wires - -

Theory:

Digital computers perform a variety of information processing tasks. Among the

functions encountered are the various arithmetic operations. The most basic arithmetic

operation is the addition of two binary digits. This simple addition consists of four

possible elementary operations: 0+0=0, 0+1=1, 1+0=0 and 1+1=10.

A binary adder-subtractor is a combinational circuit that performs the arithmetic

operations of addition and subtraction with binary numbers. A combinational circuit that

performs the addition of two bits is called half adder. One that performs the addition of

three bits is a full adder. A binary adder is a digital circuit that produces the arithmetic

sum of two binary numbers.

Procedure:

1. Connect the circuit as per the circuit diagram.

2. Power supply is switched ON and a voltage of 5v is maintained.

3. Four bit binary number is given and verifies the sum result.

4. If the adder or subtractor signal is low addition is performed.

5. If the adder or subtractor signal is high subtractor result is verified.

38

Verification Table:

Terminology Input Variables Binary inputs

Augend A3 A2 A1 A0

Addend B3 B2 B1 B0

Results Cin Cout

Addition

Subtraction

39

Description Max. Marks

Marks Secured

Preparation 30

Performance 40

Viva Voce 10

Record 20

Total 100

Staff Signature

Result:

Thus the 4 bit parallel adder/subtractor was implemented and tested using the

MSI device – IC 7483.

40

Truth Table (Even and odd parity generator):

Data Inputs Parity Bit D1 D2 D3 D4 Even Odd 0 0 0 0 0 1 0 0 0 1 1 0 0 0 1 0 1 0 0 0 1 1 0 1 0 1 0 0 1 0 0 1 0 1 0 1 0 1 1 0 0 1 0 1 1 1 1 0 1 0 0 0 1 0 1 0 0 1 0 1 1 0 1 0 0 1 1 0 1 1 1 0 1 1 0 0 0 1 1 1 0 1 1 0 1 1 1 0 1 0 1 1 1 1 0 1

41

EXP. NO : 4

DATE :

DESIGN AND IMPLEMENTATION OF PARITY GENERATOR AND CHECKER

---------------------------------------------------------------------------------------------------

Aim:

To design and implement the parity generator and checker using logic gates and

verify its performance with the verification table.


S.NO COMPONENTS RANGE QUANTITY 1 Digital IC Trainer kit - 1

2 IC 7486 1 7474 2 7404 1

3 Connecting wires - As required 4 Bread board - 1

Theory:

Parity generator:

A parity bit is a scheme of detecting error during transmitting of binary

information. A parity bit is an extra bit included with a binary message to make the

number of 1’s either odd or even.

Parity generators are used in digital transmission system for the errorless

transmission of digital data. A parity bit is added to the data before the transmission and

it will be checked for the correctness at the receiver end. There are two types of parity

systems, even parity and odd parity. In the even parity system if the number of 1’s in

the data word is odd, a 1 will be added as a parity bit to the data to make total number

of 1’s even. If the number of 1’s even, a 0 bit will be added. In the odd parity system if

the number of 1’s in the data word is odd, a 0 will be added to make the number of 1’s

odd. Otherwise, a 1 is added to make it odd. The circuit shown in the figure is used as a

parity generator as well as a checker. ABCD is the 4-bit data word. Pi and Po are the

parity input and parity output respectively.

The working of the circuit can be concluded as follows,

Work as a Parity generator:

To generate an odd parity bit for ABCD, Pi must be made 0.

To generate an even parity bit for ABCD, Pi must be made1.

Work as a parity checker:

If the parity of ABCD Pi is odd, Po will be 0.

If the parity of ABCD Pi is even, Po will be 1.

42

Circuit Diagram:

Pin Diagrams:

43

The message, including the parity bit, is transmitted and then checked at the

receiving end for errors. An error detected if the checked parity does not correspond with

the one transmitted. The circuit that generates the parity bit in the transmitter is called a

parity generator. The circuit that checks the parity in the receiver is called parity

checker. In even parity the added parity bit will make the total number of 1s an even

amount. In odd parity the added parity bit will make the total number of 1s an odd

amount.

Procedure:




connections.




44

Truth Table for Even Parity Checker

4 – BIT DATA RECEIVED PARITY ERROR

CHECK A B C D PEC 0 0 0 0 0 0 0 0 1 1 0 0 1 0 1 0 0 1 1 0 0 1 0 0 1 0 1 0 1 0 0 1 1 0 0 0 1 1 1 1 1 0 0 0 1 1 0 0 1 0 1 0 1 0 0 1 0 1 1 1 1 1 0 0 0 1 1 0 1 1 1 1 1 0 1 1 1 1 1 0

Circuit Diagram:

K-Map Simplication for Even Parity Checker

45

Description Max.

Marks

Marks

Secured

Preparation 30

Performance 40

Viva Voce 10

Record 20

Total 100

Staff Signature

Result:

Thus the Parity Generator was designed, implemented using logic gates and its

performance was verified.

46

47

EXP. NO: 5

DATE :

DESIGN AND IMPLEMENTATION OF 2 – BIT MAGNITUDE COMPARATOR ------------------------------------------------------------------------------------------------

AIM:

To design and implement a 2-bit magnitude comparator using logic gates.

COMPONENTS REQUIRED:

S.NO COMPONENTS RANGE QUANTITY 1 Digital Trainer Kit - 1

2 IC’s

7404 1 7486 1 7408 3 7432 1

3 Connecting Wires / Patch Cords

- As required

4. Bread board - 1

THEORY:

The comparison of two numbers is an operation that determines if one number is

greater than, less than, or equal to the other number. A magnitude comparator is a

combinational circuit that compares the two numbers, A and B, and determines their

relative magnitude.

The circuit for comparing two n-bit numbers has 2n entries in the truth table and

becomes too cumbersome even with n=3. On the other hand comparator circuits

possess a certain amount of regularity. The algorithm is a direct application of the

procedure a person uses to compare the relative magnitudes of two numbers. Consider

two numbers, A and B, with four digits each consider

A=A3A2A1A0

B=B3B2B1B0

The two numbers are equal if all pairs of significant digits are equal: A3=B3, A2=B2,

A1=B1 and A0=B0. When the numbers are binary, the digits are either 0 or 1, and the

equality relation of each pair of bits can be expressed logically with an EX-OR function

xi =Ai Bi + Ai ′ Bi

′ for i=0,1,2,3

The binary variables A=B=X1X0 =1.

A>B= Ai Bi′ + X1 A0 B0

′

A<B = Ai ′ Bi + X1 A0 B0

48

Truth Table (2 – Bit magnitude Comparator):

Input Output

A1 A0 B1 B0 Ai = Bi Ai > Bi Ai < Bi

0 0 0 0 1 0 0

0 0 0 1 0 0 1

0 0 1 0 0 0 1

0 0 1 1 0 0 1

0 1 0 0 0 1 0

0 1 0 1 1 0 0

0 1 1 0 0 0 1

0 1 1 1 0 0 1

1 0 0 0 0 1 0

1 0 0 1 0 1 0

1 0 1 0 1 0 0

1 0 1 1 0 0 1

1 1 0 0 0 1 0

1 1 0 1 0 1 0

1 1 1 0 0 1 0

1 1 1 1 1 0 0

49

Procedure:




connections.





Marks Secured

Preparation 30

Performance 40

Viva Voce 10

Record 20

Total 100

Staff Signature

RESULT:

Thus the 2 bit magnitude comparator was constructed using logic gates and

verified with its truth table.

50

Implementation of the following Boolean function F=Σ m (1, 3, 5 6) using multiplexer

Truth table

Minterm Inputs Output

(F) A B C

0 0 0 0 0 1 0 0 1 1 2 0 1 0 0 3 0 1 1 1 4 1 0 0 0 5 1 0 1 1 6 1 1 0 1 7 1 1 1 0

Logic diagram:

51

EXP. NO : 6

DATE :

DESIGN AND IMPLEMENTATION OF APPLICATION USING MULTIPLEXERS

----------------------------------------------------------------------------------------------

Aim:

To design and implement the combinational logic using multiplexers

Components required:

S. No

Components Name Range Type Quantity

1 Digital IC trainer kit - - 1

2 IC - 7408 2

3 IC - 7404 1

4 IC - 7432 1

5 Bread Board - - 1

6 Connecting wires - - As required

Theory:

The Block diagram shows the implementation of Boolean function using 4:1

multiplexer. The implementation table is nothing but the list of the inputs of the

multiplexer and under them list of all the minterms in two columns. The first column lists

all the minterms where least significant variable is complemented (C’), and the second

column lists all the minterms with least significant variable is un-complemented (C). The

minterms given in the function are circled and then each row is inspected separately as

follows.

If the two minterms in a row are not circled, 0 is applied to corresponding

multiplexer input.

If the two minterms in a row are circled, 1 is applied to corresponding

multiplexer input.

If the minterm in the column 1 is circled, least significant variable is

complemented (C’) and applied to the corresponding multiplexer input.

If the minterm in the column 2 is circled, least significant variable is un-

complemented (C) and applied to the corresponding multiplexer input.

52

53

Procedure:




connections.





Marks Secured

Preparation 30

Performance 40

Viva Voce 10

Record 20

Total 100

Staff Signature

Result:

Thus the implementation of the given Boolean function using multiplexer was

designed, implemented and verified with its truth table.

54

Realization of RS flip-flop using NAND gates:

Characteristic Table:

Qn(P.S) R S Qn+1(N.S)

0 0 0 0

0 0 1 1

0 1 0 0

0 1 1 Invalid

1 0 0 1

1 0 1 1

1 1 0 0

1 1 1 Invalid

Truth Table:

R S Qn+1

0 0 Qn(N.C)

0 1 1

1 0 0

1 1 Invalid

Note: N.C No Change; N.S Next State; P.S Present State

55

EXP. NO : 7

DATE :

DESIGN OF RS AND JK FLIP FLOPS USING NAND GATES

----------------------------------------------------------------------------------------------

Aim:

To design and implement RS and JK flip-flop using NAND gates.


S.NO COMPONENTS RANGE QUANTITY

1 Digital IC trainer kit - 1 2 IC’s 7400 1 3 Connecting wires - As required 4 Bread Board - 1

Theory:

Flip-flop:

The memory cell has only two states. It can be either 0 or 1. Such two state

sequential circuits are called flip-flops, because they flip from one state to another and

then flop back. A flip-flop is also known as bistable multivibrator, latch or toggle.

Types of flip-flop:

There are four different (basic) types of flip-flop. They are

1. SR flip-flop

2. JK flip-flop

3. D flip-flop and

4. T flip-flop.

Set-Reset (S-R) Flip-Flop:

The S-R flip-flop has two inputs, namely SET and RESET and two outputs Q and

Q′. The two outputs are complement to each other. The S-R flip-flop can be easily

implemented using NAND gates. The operation of NAND S-R flip-flop can be analyzed in

the same manner employed for the NOR flip-flop. If any one of the inputs is low for the

NAND gate then it will force the output high. This flip-flop is called as S-R flip-flop, i.e.,

here S=0 and R=1 will set the flip-flop.

J-K Flip-Flop:

A J-K flip-flop has a characteristic similar to that of an S-R flip-flop. In addition,

the indeterminate condition of the S-R flip-flop is permitted in it. Inputs J and K behave

like inputs S and R to set and reset the flip-flop respectively. When J=K=1, the flip-flop

output toggles, i.e., switches to its complement state. If q=0, it switches to Q=1 and

vice versa.

56

Realization of JK flip-flop using NAND gates:

Characteristic Table:

Qn(P.S) K J Qn+1(N.S)

0 0 0 0

0 0 1 1

0 1 0 0

0 1 1 1

1 0 0 1

1 0 1 1

1 1 0 0

1 1 1 0

Truth Table:

K J Qn+1

0 0 Qn(N.C)

0 1 1

1 0 0

1 1 Note: N.C No Change; N.S Next State; P.S Present State

57

Procedure:




connections.





Marks Secured

Preparation 30

Performance 40

Viva Voce 10

Record 20

Total 100

Staff Signature

Result:

Thus the flip-flops RS and JK were designed and implemented using NAND gates

and verified with their truth tables.

58

Circuit Diagram: Serial IN Serial OUT shift Register

Circuit Diagram: Serial IN Parallel OUT shift Register

59

EXP. NO : 8

DATE :

DESIGN AND IMPLEMENTATION OF SHIFT REGISTERS

------------------------------------------------------------------------------------------------

Aim:

To design, implement and verify the functioning of shift right registers (all types)

using D flip-flop.


S.NO COMPONENTS RANGE QUANTITY 1 Digital IC trainer kit - 1

2 ICs

7474 2 7408 2 7404 1 7432 1

3 Connecting wires - - 4 Bread Board - 1

Theory:

A register that is used to store binary information is known as a memory register.

A register capable of shifting binary information either to the right or the left is called a

shift register. Shift registers are classified into four types,

1. Serial-in Serial-out (SISO)

2. Serial-in Parallel-out (SIPO)

3. Parallel-in Serial-out (PISO)

4. Parallel-in Parallel-out (PIPO)

Serial-in Serial-out (SISO):

This type of shift registers accepts data serially, i.e., one bit at a time on a single

input line. It produces the stored information on its single output and the output also in

serial form. Data may be shifted left (from low to high order bits) using shift-left register

or shifted right (from high to low order bits) using shift-right register.

Serial-in Parallel-out (SIPO):

It consists of one serial input, and outputs are taken from all the flip-flop

simultaneously in parallel. In this register, data is shifted in serially but shifted out in

parallel. In order to shift the data out in parallel, it is necessary to have all the data

available at the outputs at the same time. Once the data is stored, each bit appears on

its respective output line and all the bits are available simultaneously, rather than on a

bit by bit basis as with the serial output.

Parallel-in Serial-out (PISO):

This type of shift register accepts data parallel, i.e., the bits are entered

simultaneously into their respective flip-flops rather than a bit-by-bit basis on one line.

60

Circuit Diagram: Parallel-in Serial-out shift Register

Circuit Diagram: Parallel IN Parallel OUT shift Register

61

Parallel-in Parallel-out (PIPO):

In this type of register, data inputs can be shifted either in or out of the register

in parallel.

Procedure:




connections.




62

Verification Table:

Pin Diagram:

63


Marks Secured

Preparation 30

Performance 40

Viva Voce 10

Record 20

Total 100

Staff Signature

Result:

Thus the shift registers using D flip-flop were implemented and studied their

operation in 4 different modes.

64

State Table (3 – bit synchronous binary UP counter)

Present State Next State JK Flip-Flop Inputs A B C A+ B+ C+ JA KA JB KB JC KC

0 0 0 0 0 1 0 X 0 X 1 X 0 0 1 0 1 0 0 X 1 X X 1 0 1 0 0 1 1 0 X X 0 1 X 0 1 1 1 0 0 1 X X 1 X 1 1 0 0 1 0 1 X 0 0 X 1 X 1 0 1 1 1 0 X 0 1 X X 1 1 1 0 1 1 1 X 0 X 0 1 X 1 1 1 0 0 0 X 1 X 1 X 1

JK Excitation Table:

Qn Qn+1 J K 0 0 0 X 0 1 1 X 1 0 X 1 1 1 X 0

65

EXP. NO : 9

DATE :

DESIGN AND IMPLEMENTATION OF SYNCHRONOUS COUNTER

----------------------------------------------------------------------------------------------

Aim:

To design and implement a 3-bit synchronous binary up and down counter using

JK flip-flop.


S.NO COMPONENTS RANGE QUANTITY 1 Digital Trainer Kit - 1

2 IC’s 7476 2 7408 1 7432 1

3 Connecting wires - As required 4 Bread Board - 1

Theory:

A Synchronous counter is also called parallel counter. In this counter the clock

inputs of all the flip-flops are connected together so that the input clock signal is applied

simultaneously to each flip-flop. Also, only the LSB flip-flop C has its J and K inputs

connected permanently to Vcc while the J and K inputs of the other flip-flops are driven

by some combination of flip-flop outputs.

3 – Bit Synchronous Binary UP Counter:

The J and K inputs of the flip-flop B are connected to with QC. The J and K inputs

of the flip-flop A, are connected with AND operated output of QC and QB. The flip-flop C

changes its state when with the occurrence of negative transition at each clock pulse.

The flip-flop B changes its state when QC = 1 and when there is negative transition at

clock input. Flip-flop A changes its state when QC = QB

= 1 and when there is negative

transition at clock input.

3 – Bit Synchronous Binary DOWN Counter:

The J and K inputs of the flip-flop B are connected to with QC’. The J and K inputs

of the flip-flop A, are connected with AND operated output of QC’ and QB’. The flip-flop C

changes its state when with the occurrence of negative transition at each clock pulse.

The flip-flop B changes its state when QC’ = 1 and when there is negative transition at

clock input. Flip-flop A changes its state when QC’ = QB’ = 1 and when there is negative

transition at clock input.

66

Circuit Diagram:

67

Procedure:




connections.




Pin Diagram:

68

State Table (3 – bit synchronous binary DOWN counter)

Present State Next State JK Flip-Flop Inputs A B C A+ B+ C+ JA KA JB KB JC KC

0 0 0 1 1 1 1 X 1 X 1 X 0 0 1 0 0 0 0 X 0 X X 1 0 1 0 0 0 1 0 X X 1 1 X 0 1 1 0 1 0 0 X X 0 X 1 1 0 0 0 1 1 X 1 1 X 1 X 1 0 1 1 0 0 X 0 0 X X 1 1 1 0 1 0 1 X 0 X 1 1 X 1 1 1 1 1 0 X 0 X 0 X 1

JK Excitation Table:

Qn Qn+1 J K 0 0 0 X 0 1 1 X 1 0 X 1 1 1 X 0

Circuit Diagram:

69

70

State Table:

Present State Next State ‘T’ input

D C B A D+ C+ B+ A+ TD TC TB TA

0 0 0 0 0 0 0 1 0 0 0 1

0 0 0 1 0 0 1 0 0 0 1 1

0 0 1 0 0 0 1 1 0 0 0 1

0 0 1 1 0 1 0 0 0 1 1 1

0 1 0 0 0 1 0 1 0 0 0 1

0 1 0 1 0 1 1 0 0 0 1 1

0 1 1 0 0 1 1 1 0 0 0 1

0 1 1 1 1 0 0 0 1 1 1 1

1 0 0 0 1 0 0 1 0 0 0 1

1 0 0 1 0 0 0 0 1 0 0 1

Realization of ‘T’ flip-flop input using K- Map:

71

72

T flip-flop Excitation Table:

Qn Qn+1 T 0 0 0 0 1 1 1 0 1 1 1 0

Circuit Diagram:

73


Marks Secured

Preparation 30

Performance 40

Viva Voce 10

Record 20

Total 100

Staff Signature

Result:

Thus the synchronous up, down and BCD counters were designed using JK

flip-flop and verified with their state table.

74

Verification Table (4 bit binary ripple up counter):

Clock Pulse

Q3 Q2 Q1 Q0

0 0 0 0 0 1 0 0 0 1 2 0 0 1 0 3 0 0 1 1 4 0 1 0 0 5 0 1 0 1 6 0 1 1 0 7 0 1 1 1 8 1 0 0 0 9 1 0 0 1

10 1 0 1 0 11 1 0 1 1 12 1 1 0 0 13 1 1 0 1 14 1 1 1 0 15 1 1 1 1

Circuit Diagram:

75

EXP. NO : 10

DATE :

DESIGN AND IMPLEMENTATION OF ASYNCHRONOUS COUNTER

----------------------------------------------------------------------------------------------

Aim:

To design and implement a 4-bit asynchronous binary up and down counter using

JK flip-flop.


S.NO COMPONENTS RANGE QUANTITY 1 Digital IC trainer kit - 1 2

IC 7476 2

3 7400 1 4 - 1 5 Bread board - 1 6 Connecting wires - As required

Theory:

A counter, by function, is a sequential circuit consisting of a set of flip-flops

connected in a suitable manner to count the sequence of the input pulses presented to it

digital form. An asynchronous counter, each flip-flop is triggered by the output from the

previous flip-flop which limits its speed of operation. The settling time in asynchronous

counters, is the cumulative sum of the individual settling times of flip-flops. It is also

called a serial counter.

The asynchronous counter is the simplest in terms of logical operations, and is

therefore the easiest to design. In this counter, all the flip-flops are not under the control

of a single clock. Here, the clock pulse is applied to the first flip-flop, i.e. the least

significant bit stage of the counter, and the successive flip-flop is triggered by the output

is constructed using clocked JK flip-flops. The system clock, a square wave, drives flip-

flop A (LSB). The output of A drives flip-flop B, the output of B drives flip-flop C. all the J

and K inputs connected to Vcc (High (1)), which means that each flip-flop toggles on the

edge (-ve) clock pulse.

Consider initially all flip-flops to be in the logical 0 state (i.e. QA=QB=QC=QD=0).

A negative transition in the clock input which drives flip-flop A causes QA to change from

0 to 1. Flip-flop B doesn’t change its state since it is also requires negative transition at

its clock input, i.e. it requires its clock input (QA) to change from 1 to 0. With arrival of

second clock pulse to flip-flop A, QA goes from 1 to 0. This change of state creates the

negative going edge needed to trigger flip-flop B, and thus QB goes from 0 to 1. Before

the arrival of the 16th clock pulse, all the flip-flops are in the logical 1 state. Clock pulse

16 causes QA, QB, QC and QD to go logical 0 state in turn.

76

Verification Table (4 bit binary ripple down counter):

Clock Pulse

Q3 Q2 Q1 Q0

0 1 1 1 1 1 1 1 1 0 2 1 1 0 1 3 1 1 0 0 4 1 0 1 1 5 1 0 1 0 6 1 0 0 1 7 1 0 0 0 8 0 1 1 1 9 0 1 1 0

10 0 1 0 1 11 0 1 0 0 12 0 0 1 1 13 0 0 1 0 14 0 0 0 1 15 0 0 0 0

Circuit Diagram:

77

Procedure:




connections.




Pin Diagram:

78

Verification Table (BCD ripple up counter):

Clock Pulse

Q3 Q2 Q1 Q0

0 0 0 0 0 1 0 0 0 1 2 0 0 1 0 3 0 0 1 1 4 0 1 0 0 5 0 1 0 1 6 0 1 1 0 7 0 1 1 1 8 1 0 0 0 9 1 0 0 1

10 0 0 0 0

Circuit Diagram:

79


Marks Secured

Preparation 30

Performance 40

Viva Voce 10

Record 20

Total 100

Staff Signature

Result:

Thus the asynchronous up, down and BCD counters were constructed and tested

the operations with the help of their verification tables.

80

HDL for combinational logic

VHDL code for logic gates – OR gate

library ieee; use ieee.std_logic_1164.all; entity gor is port(a,b: in std_logic;

c:out std_logic); end gor; architecture arc_gor of gor is begin c <= a or b; end arc_gor;

VHDL code for logic gates – NAND gate

library ieee; use ieee.std_logic_1164.all; entity nandg is port(a,b: in std_logic;

c:out std_logic); end nandg; architecture arc_ nandg of nandg is begin c <= a nand b; end arc_ nandg;

VHDL code for logic gates – Ex-OR gate

library ieee; use ieee.std_logic_1164.all; entity gxor is port(a,b: in std_logic;

c:out std_logic); end gxor; architecture arc_gxor of gxor is begin c <= a xor b; end arc_gxor;

81

EXP. NO : 11

DATE :

HDL FOR COMBINATIONAL LOGIC Aim:

To write a VHDL code for the combinational circuits given below and simulate the

result using EDA tool.

1. Logic Gates (OR , NAND and EX-OR) 2. Half adder and Full adder

Components Required

S.No Component Name Range / Type Quantity

1 Personal Computer - 1

2 EDA Tool (ModelSim 5.5e)

- -

Theory: The basic steps involved in the Digital System Design are,

1. Specify the desired behavior of the circuit. 2. Synthesize the circuit.

3. Implement the circuit.

4. Test the circuit to check whether the desired specifications meet.

But as the size and complexity of digital system increase, they cannot be designed

manually because their design becomes highly complex. At their most detailed level,

they may consist of millions of elements (Transistors or logic gates). So, Computer aided

design (CAD) tools are used in design of digital systems. One such a tool is a Hardware

Description Language (HDL).

HDL describes the hardware of digital systems. This description is in textual form.

The Boolean expressions, logic diagrams and digital circuits (Simple and Complex) can

be represented using HDL.

The HDL provides the digital designer with a means of describing a digital system

at a wide range of levels of abstraction and at the same time, provides access to

computer aided design tools to aid in the design process at these levels.

The HDL represents digital systems in the form of documentation which can

understand by human as well as computers.

It allows hardware designers to express their design with behavioral

constructs. An abstract representation helps the designer explore architectural

alternatives through simulations and to detect design bottlenecks before

detailed design begins.

The HDL makes it easy to exchange the ideas between the designers.

It resembles a programming language, but the orientation of the HDL is

specifically towards describing hardware structures and behavior. The storage,

retrieval and processing of programs written using HDL can be performed easily

and efficiently.

HDL‘s are used to describe hardware for the purpose of simulation, modelling,

testing and documentation.

82

VHDL for full adder – Structural Model

-- Library Declaration library ieee; use ieee.std_logic_1164.all; use work.all; -- Entity Declaration entity fa is port (a,b,c:in std_logic;

sum,cout: out std_logic); end fa; -- Architecture Declaration – Structural Model architecture arc_fa of fa is component ha port(a,b:in std_logic; s,c:out std_logic); end component; component gor port(a,b:in std_logic; c:out std_logic); end component; signal s1,c1,c2:std_logic; begin ha1:ha port map(a,b,s1,c1); ha2:ha port map(s1,c,sum,c2); or1:gor port map(c1,c2,cout); end arc_fa;

VHDL for half adder – Data Flow Model

library ieee; use ieee.std_logic_1164.all; entity ha is port ( a,b: in std_logic; s,c: out std_logic); end ha; architecture arc_ha of ha is begin s <= a xor b; c <= a and b; end arc_ha;

83

Procedure:

1. Click the ModelSim SE 5.5e icon to start the simulation of VHDL code.

2. Select create a project options given on the welcome screen in order to create a

new project otherwise choose open a project to open the existing project.

3. Proper project name should be given along with the location to save the project in

the create project window.

4. In the main window go to file New Source VHDL to get in to the source

editor window.

5. Enter the VHDL source code on that source editor window and save with the

extension .vhd in the project (project created) folder and location specified

previously.

6. Select file compile in the source editor window for compiling the written code.

If there is an error debug the error, save and compile again.

7. Load the design by selecting Design load design in the main window after

successful compilation of the VHDL codes.

8. Select signals from the view menu of the main window for selecting the signals.

9. In signal window, choose edit force / clock for applying the appropriate input

levels for the signals selected.

10. Select view wave signals in design to view the response of the design (Wave

form) with the help of run option from the signal window.

11. Continue the simulation for different input levels with the procedure stated above.

Description Max.

Marks

Marks

Secured

Preparation 30

Performance 40

Viva Voce 10

Record 20

Total 100

Staff Signature

Result:

Thus the VHDL Code for the Combinational circuits was developed and simulated

using Electronic Design Automation tool.

84

HDL FOR SEQUENTIAL LOGIC

VHDL code for flip-flops (D) library ieee; use ieee.std_logic_1164.all; entity dff is port(clr,d : in std_logic; clk: in std_logic; q : out std_logic); end dff; architecture arc_dff of dff is begin process(clk) begin if(clr = '0')then

q <= '0'; elsif (clk = '1' and clk'event) then

q <= d; end if;

end process; end arc_dff;

VHDL for Synchronous UP/DOWN counter Library ieee; use ieee.std_logic_1164.all; use ieee.std_logic_unsigned.all; entity synudcounter is port( clk: in std_logic; clr: in std_logic; ud: in std_logic; cout: inout std_logic_vector(3 downto 0)); end synudcounter; architecture arc_synudcounter of synudcounter is begin process(clk) begin if (clk = '0' and clk'event) then if(clr = '0') then cout <= "0000"; else if(clr = '1' and ud = '0') then cout <= cout + 1; elsif(clr = '1' and ud = '1') then cout <= cout - 1; end if; end if; end if; end process;

end arc_synudcounter;

85

EXP. NO : 12

DATE : HDL FOR SEQUENTIAL LOGIC

Aim:

To write a VHDL code for the sequential circuits given below and simulate the

result using EDA tool.

1. D flip – flop 2. Synchronous UP / DOWN Counter

Components Required

S.No Component Name Range / Type Quantity

1 Personal Computer - 1

2 EDA Tool (ModelSim 5.5e)

- -

Theory: The basic steps involved in the Digital System Design are,

1. Specify the desired behavior of the circuit.

2. Synthesize the circuit.

3. Implement the circuit.

4. Test the circuit to check whether the desired specifications meet.

But as the size and complexity of digital system increase, they cannot be designed

manually because their design becomes highly complex. At their most detailed level,

they may consist of millions of elements (Transistors or logic gates). So, Computer aided

design (CAD) tools are used in design of digital systems. One such a tool is a Hardware

Description Language (HDL).

HDL describes the hardware of digital systems. This description is in textual form.

The Boolean expressions, logic diagrams and digital circuits (Simple and Complex) can

be represented using HDL.

The HDL provides the digital designer with a means of describing a digital system

at a wide range of levels of abstraction and at the same time, provides access to

computer aided design tools to aid in the design process at these levels.

The HDL represents digital systems in the form of documentation which can

understand by human as well as computers.

It allows hardware designers to express their design with behavioral

constructs. An abstract representation helps the designer explore architectural

alternatives through simulations and to detect design bottlenecks before

detailed design begins.

The HDL makes it easy to exchange the ideas between the designers.

It resembles a programming language, but the orientation of the HDL is

specifically towards describing hardware structures and behavior. The storage,

retrieval and processing of programs written using HDL can be performed easily

and efficiently.

HDL‘s are used to describe hardware for the purpose of simulation, modelling,

testing and documentation.

86

Procedure:

1. Click the ModelSim SE 5.5e icon to start the simulation of VHDL code.

2. Select create a project options given on the welcome screen in order to create a

new project otherwise choose open a project to open the existing project.

3. Proper project name should be given along with the location to save the project in

the create project window.

4. In the main window go to file New Source VHDL to get in to the source

editor window.

5. Enter the VHDL source code on that source editor window and save with the

extension .vhd in the project (project created) folder and location specified

previously.

6. Select file compile in the source editor window for compiling the written code.

If there is an error debug the error, save and compile again.

7. Load the design by selecting Design load design in the main window after

successful compilation of the VHDL codes.

8. Select signals from the view menu of the main window for selecting the signals.

9. In signal window, choose edit force / clock for applying the appropriate input

levels for the signals selected.

10. Select view wave signals in design to view the response of the design (Wave

form) with the help of run option from the signal window.

11. Continue the simulation for different input levels with the procedure stated above.

Description Max.

Marks

Marks

Secured

Preparation 30

Performance 40

Viva Voce 10

Record 20

Total 100

Staff Signature

Result:

Thus the VHDL Code for the Sequential circuits was developed and simulated

using Electronic Design Automation tool.

Documents

Digital Lab Manual for CSE & IT - Anna Univeristy Chennai Syllabus - 2012