DRILL PIPE DATATOTAL NUMBER OF JOINTS INSPECTED 2TOTAL NUMBER OF
JOINTS ACCEPTED READY FOR USE 0TOTAL NUMBER OF JOINTS CLASS 2
0TOTAL NUMBER OF JOINTS SCRAP 0
MACHINE SHOP REPAIRS REQUIREDTOTAL PIN CONNECTION FOR RE-WORK
2TOTAL BOX CONNECTIONS FOR RE-WORK 2TOTAL PIN HARDBAND FOR REPAIR
0TOTAL BOX HARDBAND FOR REPAIR 0TOTAL CENTER WEAR PAD HARD BAND FOR
REPAIR 0TOTAL INTERNAL PLASTIC COATING FOR REPAIR 0TOTAL JOINTS
BENT 0TOTAL PIN CONNECTION RE-FACE MACHINE 0TOTAL BOX CONNECTIONS
RE-FACE MACHINE 0TOTAL JOINTS FOR REPAIR 2
1 - Coating Intact
2 - Coating with more than 70% intact
3 - Coating with more than 30% deteriorated
4 - Coating with more than 50% deteriorated
5 - No coating C4B = Cut Over 20% K = Necking
MA = Mashed TW =Thread Wear
DB = Damaged Bevel PNR = Pin Neck Rejected NSRG = No Stress
Relief Groove
1 - NEW CONDITION OR SLIGHT WEAR B = Bent MRF = Machine Reface
CORR = Corrosion
2 - MODERATE WEAR O = Obstructed WO = Washout
3 - EXCESSIVE WEAR 1/32 STS = Short Tong Space NBB = No
Boreback
4 - MAJOR SECTIONS OF BAND LOST P = Premium EW = Eccentric Wear5
- NOT HARD BAND PS = Pin Stretched OK = Approved6 - HARD BAND
DAMAGED (larger than 1/8 in dimension) SC = Scrap REJ = Rejected
ACC = Accepted
CSD = Crushed
GAL = Galling
ND = No Drift
C3 = Classe 3
REMARKS / CONDITION
STR = Straightened
CR = Cracked
C2 = Classe 2 EP = External Pitting
TD - Thread Damaged
G = Gouge
SAD = Slip Area DamageBS = Box Swell
Page 1 of 1 Summary Report
Ventura15002190 OJ
Base IRM - Maca
API RP 7G2 STANDARDIRM-QCP-DS-I-004
CUSTOMERP.OINSPECTION LOCATION RIG Ventura Petroleo
1648Drill Pipe 5 1/2" - R-II - Weight 21.90 CON.5 1/2" FH
Poliana Brando
IRM JOB NUMBERMATERIAL DESCRIPTIONCUSTOMER CONTACTSERVICES
PERFORMED QUALITY PLAN NUMBER
INTERNAL COATING CONDITION
HARD BAND CODE
EXP = ExpandedOT = Overtorqued
RW = Rework SFN = Short Fishing Neck PO = Porosity
C4A = Cut Over 10% IP = Internal Pitting LW = Low Wall
D = Dent
SD = Seal Damaged
DOR = Dim.Out of Range
SS = String Shot
F-DS-I-033 Rev.1
AC YOKE U.V METER IRM/MLU/34U.V LIGHT COIL IRM/DCMC 12/23UT T
MIKE PIT GAUGE IRM/MPF/26UTEAEMI
PIN BOXRUN SERIAL OD BEV SEAL Shouder TONG ID HB PIN PIN OD BEV
SEAL Shouder TONG HB CB CB COND COND UT UT SA IPC EMI CLASSNO.
NUMBER PIN DIA WIDTH WIDTH SPACE PIN NECK LENGTH BOX DIA WIDTH
WIDTH SPACE DIAM. DEEP WALL EA MPI GRADE ACC/REJ
1 BS-0246 7 13/32" 7 1/8" 9/16" 7/8" 10 1/8" 3 1/2" 5 17/32" 4
15/16" 7 13/32" 7 5/32" 9/16" 23/32" 8" 3 5 29/32" 11/16" CORR
CORR/SD OK 0.384 N/A OK 2 OK P
2 BS-0227 7 13/32" 7 1/8" 9/16" 7/8" 9 7/8" 3 1/2" 5 17/32" 4
15/16" 7 13/32" 7 3/64" 1/2" 23/32" 8 13/32" 3 5 7/8" 19/32" CORR
CORR/SD OK 0.377 N/A OK 2 OK P
MRF 0 0 P 2RW 2 2 C2 0OK 0 0 SC 0
COMMENTS:
INSPECTOR (S): Ilton da Silva Eccard / Weslley Gomes Daudt
QUALIFICATION (S): PM-N2-SY- BO / US-N2-S2 ASNT , PM-N2-SY- BO /
US-N2-S2 ASNT
MATERIAL
TUBE BODY
ODG
Signature:
SC = ScrapOK = Approved
PIN BOX
GRADE RANGE CONNECTION WEIGHT HARDBAND
Carbon Steel R-II3 1/2"
Page 1 of 1Drill Pipe Inspection Report
Drill Pipe Inspection - Drill PipeEQUIPMENT DATA
CUSTOMER CONTACT: Poliana Brando
IRM/YK/82IRM/UVL/23IRM/UTDMS/01N/AIRM/EMI 02
CUSTOMER: Ventura P.O NUMBER: 15002190 OJ
SPECIFICATION: API-RP-7G-2 Std
P = Premium RW = ReWork
DATE: 10/07/2015
RIG : Ventura PetroleoIRM NUMBER: 1648
IRM WORK INSTRUCTIONS: I-DS-I-001; 002; 003; 004; 007; 015; 016;
017. ID OD
REMARKS / CONDITIONMRF = Machine Reface C2 = Classe 2
21.90 YESS-135 5 1/2" FH5 1/2"
F-DS-I-011a Rev.10
F-DS-I-020 - Capa - Front Cover - ensco 1153 hw DATABOOK
MATERIAL LISTSummary Report - Drill Pipe 5 12 - R-II - Weight
21.90 CON.5 12 FHDrill Pipe 5 12 - R-II - Weight 21.90 CON.5 12 FH-
Drill Pipe Inspection Report - Rev.10
