Development of DIMTS Office at 8th Floor, DMRC IT Park .... Bill of... · Cost to include 20 mm wide border frosting of mirror. SqM 24.00 9.00 MDF Panelling MDF PANELING : As per

Bill No. Description Amount (INR)

1 Civil & Interior Works -

2 HVAC Works -

3 Electrical Works -

4 Fire Fighting System/Works -

5 FDA System -

6 Access Control System -

7 CCTV System -

8 PA System -

9 IT Networking System -

10 UPS System -

11 Modular Workstation & Loose Furniture -

12 Development of working Detailed Drawings for civil and

services

13 Total Sum -

Development of DIMTS Office at 8th Floor, DMRC IT Park, Shastri Park, Delhi

Bill of Quantities

Summary Sheet

Note: The rates and prices is deemed to include all plant, labour, supervision, materials, transport, all temporary works,

erection, maintenance, taxes (including GST) and duties, contractor’s profit and establishment/overheads, together with

preparation of design and drawings, all general risks, insurance liabilities, compliance of labour laws and any other

obligations set out or implied in the contract.

Bill Summary 1 of 49

In Figures (INR) In words (INR)

A CIVIL WORKS

1.00 Dismantling

a Dismantling brickwork manually/by mechanical means

including stacking of servicable material and disposal of

unservicable material outside the premises to nearest sanitary

landfill site

cum 67.91

b Dismantling plain cement concrete 1:3:6 or richer mix

manually/by mechanical means including disposal of

demolished material outside the premises to nearest sanitary

landfill site

cum 226.54

c Disposal of moorum/building rubbish/ malba/ similar

unserviceable, dismantled or waste material by mechanical

transport including loading, transporting, unloading to

approved municipal dumping ground for lead upto 10 km for all

lifts, complete as per directions of Engineer-in-charge

cum 25.00

2.00 Half Brick Masonary with FPS bricks of class designation 75 in

cement mortar 1:3(1 cement : 4 coarse sand) including

providing & placing in position 2 Nos. 6 mm diameter MS bar

reinforcement at every third course of half brick masonary.

SqM 83.00

3.00 Brick work with FPS bricks of class designation 75 in cement

mortar 1:6(1 cement : 6 coarse sand)

cum 20.70

4.00 12mm cement plaster of mix 1:4(1 cement : 4 fine sand) SqM 607.50

5.00 15mm cement plaster on the rough side of single or half brick

thick wall of mix 1:4(1 cement : 4 fine sand)

SqM 150.00

6.00 POP Puning: Providing & applying average 2mm thick plaster of

Paris and wiremesh at joints of diff materials to the walls and

columns in square plumb line and level including scraping and

removing the existing finish, hacking the surface of

walls/columns. After leveling, the surfaces to be finished to

receive paint etc. Rate to include providing for Al channels and

grooves at all junctions and corners.

SqM 729.00

7.00 Reinforceed concrete work in beams, suspended floors,

shelves, chajjas, lintels, bands etc. including the cost of

centering/shuttering/finishing with 1:1.5:3(1 cement : 1.5

coarse aggregate : 3 graded stone aggregate 20mm nominal

size)

cum 6.90

Rate (INR)

Bill of Quantities

Bill No. 1 : Civil & Interior Works


Amount in figures

(INR)S.NO

DESCRIPTIONUNIT

Quantity

Estimate 2 of 49


Rate (INR)

Bill of Quantities


Amount in figures

(INR)S.NO

DESCRIPTIONUNIT

Quantity

8.00 Providing and laying in position cement concrete of specified

grade excluding the cost of centering and shuttering - All work

up to plinth level :

1:2:4 (1 cement : 2 coarse sand (zone-III) : 4 graded stone

aggregate 20 mm nominal size)

cum 220.00

9.00 Reinforcement for RCC work including straightening, cutting,

bending, placing in position and binding all complete : TMT

bars

kg 345.00

10.00 Granite Counters:

Granite Counters: Constructing RCC platform of 75 mm thick.

with adequate reinforcement including shuttering, curing etc. in

1:2:4 concrete, in toilet/pantry/kitchen with 115 mm thick

brick upstands as required and directed, at 800-850 mm height

and 600/550 mm width. Finish with 20 mm thick polished

Black Galaxy/Steel Grey Granite , with machine cut & polished

edges including splash-back and fascia all within 200 mm

height all laid/fixed with rich cement mortar mix.

Sqm 80.00

11.00 Cement Concrete Leveling Screed:Providing & laying CC 1:2:4

(1 cement : 2 coarse sand : 4 graded stone aggregate

20/12.5mm nominal size)screed on floor( 75mm avearge

thickness) laid with glass strips in panels not exceeding 2.5-

sq.m. The entire top surface to be finishede TRUE HORIZONTAL

as measured through a water-level so as to attain an

evenness/ horizontal surface to an extent of +- 5 mm

(minimum-to-maximum)

Sqm 100.00

12.00 Providing fixing thermal insulation of ceiling (under deck

insulation) with Resin Bonded Fibre glass wool conforming to

IS : 8183, density 24kg / m3, 50mm thick, wrapped in 200 G

Virgin Polythene bags, fixed to ceiling with metallic cleats

(50x50x3 mm) @ 60 cm and wire mesh of 12.5 mm x 24

gauge wire mesh, for top most ceiling of building.

SqM 200.00

B SANITARY & PLUMBING

1.00 Providing & Fixing Single Bowl Sink for Pantry including CP jali

& PVC waste pipe (Make : Nirali or Equivalent)

Nos. 4.00

Estimate 3 of 49


Rate (INR)

Bill of Quantities


Amount in figures

(INR)S.NO

DESCRIPTIONUNIT

Quantity

2.00 Providing and fixing white vitreous china pedestal type water

closet (European type) with seat and lid, 10 litre low level

white vitreous china flushing cistern & C.P. flush bend with

fittings & C.I. brackets, 40 mm flush bend, overflow

arrangement with specials of standard make and mosquito

proof coupling of approved municipal design complete,

including painting of fittings and brackets, cutting and making

good the walls and floors wherever required :

W.C. pan with ISI marked white solid plastic seat and lid for

Ladies and gents toilet

Nos. 18.00

3.00 Providing and fixing white vitreous china flat back half stall

urinal of size 580x380x350 mm with white PVC automatic

flushing cistern, with fittings, standard size C.P. brass flush

pipe, spreaders with unions and clamps (all in C.P. brass) with

waste fitting as per IS : 2556, C.I. trap with outlet grating and

other couplings in C.P. brass, including painting of fittings and

cutting and making good the walls and floors wherever

required :

Range of two half stall urinals with 5 litre P.V.C. automatic

flushing cistern for Gents toilet

Nos. 8.00

4.00 Providing and fixing PTMT bib cock of approved quality and

colour. 15 mm nominal bore, 122mm long, weighing not less

than 99 gms for Ladies and gents toilet

Nos. 15.00

5.00 Providing and fixing toilet paper holder C.P. brass for Ladies

and gents toilet

Nos. 18.00

6.00 Providing and fixing 8 mm dia C.P. / S.S. Jet with flexible tube

upto 1 metre long with S.S. triangular plate to Eureopean type

W.C.for Ladies and gents toilet of quality and make as

approved by Engineer - in - charge.

Nos. 18.00

C JOINERY

1.00 Frameless Glazed Partitions, Toughened

FULL HEIGHT FRAMELESS TOUGHENED GLAZED PARTITION:

Fabricating and fixing of 10mm thk. Toughened Glass partitions

with concealed fixing arrangement in floor & ceilings as per

drawings/Technical specifications and as directed by Engineer-

in-Charge. The rate shall include sealing all joints with non

staining clear silicon sealant, machine cut polished edges,

tapers to design.

SqM 452.50

Estimate 4 of 49


Rate (INR)

Bill of Quantities


Amount in figures

(INR)S.NO

DESCRIPTIONUNIT

Quantity

2.00 75 mm Thk. Full Height Partitions with Ply on both Sides

without any Panelling.

FULL HEIGHT PARTITION: Providing and fixing 75 mm thick

partition faced both sides with 12 mm thick fire retardent ply,

screw fixed with dry wall screw of 25 mm at 300 mm centers to

either sides of 48 mm GI studs (.55 mm thick), having one

flange of 34 mm and other flange of 36 mm, placed at 610 mm

center to center (both ways) in 50 mm floor and ceiling

channels of 32 mm section. Skirting, door junction and

material transition sections to be in hardwood frame 50 x 50 to

provide 10x10 grooves at all ends. If any hardwood sections

are provided, these are to be coated all over with 2 or more

coats of viper anti-termite/fire retard paint. Inside voids to be

filled with 50 mm thick panels of glass wool/ rock wool. All

edges to be protected with aluminum angles.

SqM 385.20

3.00 Gypsum Borad Single Side Partition

GYPSUM BOARD SINGLE SIDE PARTITION : Form full height

Panelling on existing column or wall surface with GI Channels

and studs as per Item No. C 2 above but one side faced with

12 mm thick Gypsum Board complete with jointing and taping.

SqM 1110.00

4.00 Fabric Panelling

FABRIC PANELING: P&F paneling over existing partition (Item

No. C 2 above), formed of 12 mm thick Cellotex board wrapped

in fabric. Fabric Shade as approved :Sabhajeet Fabrics - SF

1417 - Pista Green.

SqM 291.60

5.00 Gypboard panelling

GYPBOARD PANELLING: 12 mm Thk. Gypsum Board Paneling

on existing 75 mm Thk. Partition (Item No. C 2 above)

complete with jointing and taping.

SqM 181.00

6.00 Color Back Glass Panelling

COLOR BACK GLASS PANELLING: Form paneling on existing

partitions (Item No. C 2 above) with 10 mm thick Non

Toughened glass. Back of the glass to be painted with duco

paint of Architect’s approved shade. Backing Ply face to be

painted with color to match the glass. Glass to be fixed with

dow corning/ 3M high bond tape of adequate bond strength, to

laminated strips affixed to the backing ply.

SqM 291.60

Estimate 5 of 49


Rate (INR)

Bill of Quantities


Amount in figures

(INR)S.NO

DESCRIPTIONUNIT

Quantity

7.00 Laminated PanellingLAMINATED PANELING: Form paneling on

existing partition (Item No. C 2 above) with 12 mm thick fire

retardent ply and finished with 1 mm thick laminate as per

architect’s approval including Providing for 10 mm x 10 mm

grooves as required. Laminate Shade as approved : Merino

Laminates Walnut Bronze 10510.

SqM 291.60

8.00 Mirror Panelling

MIRROR PANELING: For panelling faced with 6mm Mirror fixed

on 10mm thk ply to be flush in level with adjoining surfaces.

Cost to include 20 mm wide border frosting of mirror.

SqM 24.00

9.00 MDF Panelling

MDF PANELING : As per item number C 3 above but faced with

12mm thk MDF instead of gypsum board. MDF to be finished

with DuPont refinish paint and buff finished to Architect’s

approval

SqM 40.00

10.00 Glass Panelling with Studs

GLASS PANELLING WITH STUDS: Fabricating and installation of

10 mm thick tempered glass paneling mounted with SS studs

upon existing structure.

SqM 16.00

11.00 Wall paper Panelling

WALL PAPER PANELLING: P&F Wall paper paneling over

adequate leveled surface in approved design. Wall paper to

have PVC coated paper backing. Minimum width of 70cm per

roll. Total weight 400g/sqm.

SqM 125.00

12.00 Partitions above false ceiling

PARTITIONS ABOVE FALSE CEILINGS: Partitions as item no. C

2 above but entirely of GI frame and without skirting, to be

installed over false ceilings.

SqM 125.00

13.00 Laminated Skirting

LAMINATED SKIRTING: Fabricating and fixing 100 mm high 12

mm thick ply skirting, fascia and edges finished with 1 mm

thick laminate of approved shade, fixed flush with wall /

existing partition (Item No. C 2) finish with 10 mm Alum.

channel groove as per details and Architects instructions.

Skirting to be fixed flush to plastered/POP/ partition finished

wall surface. Laminate Shade as approved : Merino Laminates

Walnut Bronze 10510

RM 500.00

Estimate 6 of 49


Rate (INR)

Bill of Quantities


Amount in figures

(INR)S.NO

DESCRIPTIONUNIT

Quantity

14.00 PELMET: Fabricate and install pelmet made of 19 mm thick

board, up to 300 mm high and in line with external glazing as

per details of Architect. Rate to include finishing exposed

surfaces of the Pelmet with enamel paint of approved shade.

Pelmet to be ready to receive blinds.

RM 50.00

15.00 RECESSED PELMET FOR SCREENS: As per item no. C 14 above

but of width 250 mm and height 250 mm, cut into gypsum

false ceilings and ready to receive projection screen.

RM 10.00

16.00 Worktop Counter Laminated

WORK TOP COUNTER LAMINATED: Fabricating & fixing up to

750 mm deep and 720 ht worktop counter formed out of 25

mm thick mdf board faced with .8mm thick post formed

laminate of approved shade. Front edge of counter to be post-

formed beveled waterfall edge or as per other designs provided

by the architect. Maplewood sections to be stained and

melamine polished to Architect’s approval.Laminate Shade as

approved : Merino Laminates Walnut Bronze 10510.

RM 200.00

17.00 Laminated Shelves

LAMINATED SHELVES: Fabricate and install 200 mm deep,

1200/1500 mm long Laminated shelves. Shelf to be mounted

on to existing partitions, walls etc as directed with concealed

fixing detail. Shelves to be fabricated with 2 Nos. 19 mm thick

board, with 19 mm filler pieces, faced all sides with 1 mm thick

Laminate to form overall thickness of 60 mm. Laminate Shade

as approved : Merino Laminates Walnut Bronze 10510

Nos 50.00

18.00 Window Cill

WINDOW CILL: Fabricate and install 250-350 mm wide,

window cill along external windows. Cill to be constructed out

of 19 mm Commercial board, and faced with 4 MM thick Maple

Veneer, stained to approved color and melamine spray polished

to Architect’s approval.

RM 14.00

D BUILT IN STORAGE

Estimate 7 of 49


Rate (INR)

Bill of Quantities


Amount in figures

(INR)S.NO

DESCRIPTIONUNIT

Quantity

1.00 Full Ht. Storage: Laminated

FULL HEIGHT STORAGE, LAMINATED: Fabricating and fixing full

height storage cupboards as per details. Top, bottom and

shelves to be made out of 19 mm thick commercial board, back

to be provided of 6 mm thick commercial ply, shutters to be

made out of 19 mm thick commercial board faced with 1.00

mm thick laminate. All internal surfaces to be faced with 0.8

mm thick laminate of approved shade. External surfaces

finished on exposed sides with 1 mm thick laminate. Complete

with all necessary fittings like hinges, ball catchers, tower

bolts, locks, handles, adjustable shelves etc. as per directions

of Architect. Cupboard depth of 400-450 mm. Adjustable

shelves to be supported on half cut; 10 mm dia s.s glass pins.

Laminate as approved : Internal Laminate : Merino Laminated

Frosty White 21091, External Laminate : Merino Laminates

Walnut Bronze 10510.

SqM 25.00

2.00 Low Height Storage: LaminatedLOW HEIGHT STORAGE

LAMINATED: Form low height storage of 750 mm ht. as per

details and specifications of item no D 1 above but with the top

and side surfaces also finished with 1 mm thick laminate.

Provide one adjustable shelf. Laminate as approved : Internal

Laminate : Merino Laminated Frosty White 21091, External

Laminate : Merino Laminates Walnut Bronze 10510.

Sqm 25.00

3.00 Overhead storage : Laminated

OVERHEAD STORAGE LAMINATED: Form as per item D 1 above

but of height 1000/1200 mm and hung onto wall. All exposed

surfaces faced with 1 mm thick laminate \. Storage to include

shutters and also open shelves. Laminate as approved :

Internal Laminate : Merino Laminated Frosty White 21091,

External Laminate : Merino Laminates Walnut Bronze 10510.

Sqm 27.00

E DOORS

Estimate 8 of 49


Rate (INR)

Bill of Quantities


Amount in figures

(INR)S.NO

DESCRIPTIONUNIT

Quantity

1.00 Main Entrance Door : Type D 1

MAIN ENTRANCE DOOR: Providing and fixing Double leaf

10mm toughened glass door. Rates to be inclusive of all

necessary hardware fittings including SS handle, lock, stopper

and stay. Overall door size to be 1500 x 2400 mm. Hardware

set to be as follows:

• D-Line SS 316 Pull handle pair, 38 mm dia of length 1100

mm, with three fixing centers.

• Dorma Top pivot SM 1001

• Dorma Upper and lower patch SM 1010

• Dorma Floor spring BTS, 75 V with EP cylinder

• Dorma Strike Plate SM 1052 E

• Dorma floor lock SM 1049 E

• Dorma door stopper TZ 5000

Nos 4.00

2.00 Frameless Glazed : Type D 2

FRAMELESS GLAZED DOOR: Providing and fixing 10mm

Toughened glass door 2400/2500 mm x 1000 mm. Refer

Drawing No.DT 109. The shutter will be fixed on Ozone Patch

fitting set inclusive on top and bottom patch, lock set and floor

spring. Rates to be inclusive of all necessary hardware fittings

including SS handle, lock, stopper and stay. Hardware set to be

as follows:

• Ozone 9400 Floor Spring with

• Ozone Top pivot OPF 2

• Ozone Bottom Pivot OPF 3

• Ozone Patch lock OPL1

• Small Pivot FS ACC GDP

• H type brushed SS Handle Set, 35 x 1000 mm

• D shaped floor mounted door stopper

Nos 40.00

Estimate 9 of 49


Rate (INR)

Bill of Quantities


Amount in figures

(INR)S.NO

DESCRIPTIONUNIT

Quantity

3.00 Flush Door, Laminated D 03

FLUSH DOORS LAMINATED 1000 MM: P&F Semi solid core

laminated door formed out of 25X 100 mm wide CPTW frame 6

mm thick ply skins, and faced both sides with 1 mm thick

laminate to form overall thickness of 40 mm. 50X 100 section

Maplewood chowkhat. All wooden sections to be stained and

melamine polished to Architect’s approval. All handles to be in

brushed SS finish of Dorset or equivalent make and Architect’s

approved model. Complete with all hardware including locks,

door closer, door stoppers etc as required. Overall door size to

be 2500 mm x and up to 1000 mm. Hardware set to be as

follows:

• Ozone Heavy Duty Door Closer NSK – 680

• Chrome Plated Brass Hinges, 100 mm x 75 mm x 3 mm

hinges, 4 Nos.

• Dorset SS lever handle with mortise lock.

Nos 20.00

4.00 Flush Door with Vision Panel : D 04FLUSH DOORS, LAMINATED

WITH VISION PANEL: P&F Semi solid core LAMINATED DOOR

formed out of 25X 100 mm wide CPTW frame 6 mm thick

comm. ply skins, and faced both sides with 1 mm thick

Laminate to form overall thickness of 40 mm. 3/6mm grooves.

Including 50X 100 section MAPLE /Pine wood chowkhat. All

wood faces to be stained and melamine polished to Architect’s

approval. Door to have vision panel formed of 8/10mm

toughened glass. Sizes of cut-outs as per detailed drawing.

Complete with all hardware including locks, door closer,

doorstoppers etc as required. Hardware set as per item number

F.03 above. Overall door size to be 2400/2550 x 1000 mm.

6.00

F MISCELLANEOUS ITEMS

1.00 Frosting Film on Glazed Partitions

FROSTING FILM: Provide and apply 3M or equivalent make

frosting film, sparkle finish, on glazed partitions doors etc. in

patterns as provided by the Architects.

SqM 200.00

2.00 Graphic Film :

Graphic Film : Provide & Install Graphic printed on 3 M Film as

approved on Glass / Partition Surface.

SqM 180.00

Estimate 10 of 49


Rate (INR)

Bill of Quantities


Amount in figures

(INR)S.NO

DESCRIPTIONUNIT

Quantity

3.00 Reception Backdrop Partition

Provide & Install Reception Backdrop Partition/Boxing of 300

mm depth boxing made in hardwood menmbers framing

finished with 6 mm corian in approved shade. Back of the

Reception Backdrop to be made as openable shutters in 19 mm

thk. commercial board finished with 1mm Thk. Laminate as

approved.

Sqm 30.00

G FLOOR & WALL FINISHES

1.00 Vitrified Tile Flooring - 2'0"x2'0"

VITRIFIED TILE FLOORING: Providing and laying vitrified tile

flooring of size 600 mm x 600 mm, in locations as directed,

laid to required slope in 1: 4 cement coarse sand mortar up to

50 mm thick. With tile grout joints of approved width finished,

in colored tile grout, Roff chemicals/ bal or equivalent make.

Approved Tiles : City Rain Bone (Somany Global) and MSE

66110 (Somany Global)

SqM 2000.00

2.00 Ceramic Tile Flooring (For Pantry)

CERAMIC TILE FLOORING: Providing and laying matt finish,

300X300 MM ceramic tiles. In locations as directed, laid to

required slope in 1: 4 cement sand mortar up to 50 mm thick.

With tile grout joints of approved width finished, in colored tile

grout, Roff chemicals or equivalent make.

SqM 150.00

3.00 Laminated Parquet Flooring LAMINATED PARQUET FLOORING:

Providing & Installation of Laminated parquet flooring of Grade

4, commercial grade, composed of water repellant HDF panels

with direct pressure laminate and protective laminate based

abrasion resistant film. Thickness of panels to be 11mm

including underlay. Rate to include underlay, floor transition

strips and all accessories as required. Floor to be Pergo as per

shade approved. Approved Flooring Shade : Pergo Italian

Walnut Plank (72116-0945)

SqM 275.00

4.00 Designer Vinyl Flooring

VINYL FLOORING: P&I Vinyl flooring, commercial grade, of O/A

thickness 3.3 mm and wearlayer thickness of 0.62mm and

weight 2795 g/sqm. Floor to be fixed with proprietary

recommended adhesive. Rate to include self leveling screed (of

Bal chemicals) layer of 1 to 2mm thkness to achieve zero

level. Max deflection for a 2M spirit level : 7mm, for a 0.20M

spirit level : 2mm. Range to be considered LG Deco Fine Wood

or equivalent from Armstrong.

SqM 25.00

Estimate 11 of 49


Rate (INR)

Bill of Quantities


Amount in figures

(INR)S.NO

DESCRIPTIONUNIT

Quantity

5.00 Anti Stat Vinyl Flooring

ANTI STAT FLOORING: Provide and install 3mm thick, flooring

grade anti stat laminate flooring on existing/ prepared sub

floor. Approved make: Bakelite Hylam, Armstrong or

equivalent. Any minor repair works to be carried out by vendor

at no extra cost.

SqM 50.00

6.00 Access Floor - 150mm / 300 mm high

ACCESS FLOOR: Providing and fixing access floor panels

adjustable (150+/- 20mm) or (300+/- 20mm) height under

floor construction of light weight grade (15 KN/m2) UDL panels

of 600x600x31mm thickness faced with 3 mm thick anti stat

laminate on top, with BTW stained black edge lipping of

tapered profile and aluminum sheet at the bottom. Unifloor

make or equivalent. Adjustable jacks to be manufactured from

pressed formed corrosion resistant galvanized steel, placed on

the pedestal (of axial load 22.5 KN), zinc plated consisting of

anti-vibration head cap with cruciform up-stand and four panel

locating studs, etc. complete. The rate to include cutting tiles

for access to services and also includes supply of 1nos. of

vacuum tile lifter.

SqM 50.00

7.00 Vitrified Tile SkirtingVITRIFIED TILE SKIRTING: Provide and Fix

Vitrified Tile Skirting, 100 mm high, on walls / columns in

lengths specified by Architects, of overall specifications as per

item no G 1 above. Skirting to be flush with finished surface of

walls / columns. Include breaking and removing existing

plaster / skirting and applying up to 12 mm thick 1:3 (1

cement: 3 coarse sand) cement mortar backing.

RM 50.00

8.00 Wall Tiles for Pantry

CERAMIC WALL TILES TYPE 1: Providing and fixing plain white

200x200, 600X600 ceramic tiles, laid in 1:3 cement coarse

sand mortar, up to 12 mm thick for dado upto ceiling height in

pattern indicated by Architect in toilets / pantry and other

locations with mortar as item A5 and thickness necessary to

bring the surface plumb and minimize cut tiles/ joints. Tile

joints to be finished with approved make tile grout in thickness

as directed.

SqM 50.00

Estimate 12 of 49


Rate (INR)

Bill of Quantities


Amount in figures

(INR)S.NO

DESCRIPTIONUNIT

Quantity

9.00 Enamel Paint

ENAMEL PAINT: Providing and applying enamel paint to

gypsum walls, POP puning, Gypsum ceiling and existing

plastered ceiling, including paint putty, base coat as pre

manufacturers recommendations and finishing with 2/3 coats

of enamel paint of approved color and make. Surface coating

to be achieved as per manufacturer’s recommendations for

coverage of paint.

SqM 100.00

10.00 Light Textured Emulsion PaintEMULSION PAINT: Providing and

applying plastic light textured emulsion paint to gypsum walls,

POP puning, Gypsum ceiling and existing plastered ceiling,

including paint putty, base coat as pre manufacturers

recommendations and finishing with 2/3 coats of plastic

emulsion paint of approved color and make. Surface coating to

be achieved as per manufacturer’s recommendations for

coverage of paint.

SqM 2400.00

11.00 Duco Paint

DUCO PAINT: Providing and applying DuCO paint finish To be

applied as per manufacturer’s recommended method of

application. Shade of Paint as per any selection made by

Architect, including the metallic range.

SqM 100.00

1.00 Gypsum Board Ceiling

GYPSUM BOARD CEILING: P&F 12 mm thick Gypsum board to

G.I. framing perfect in level including making grooves at the

junction of ceiling and walls/columns/partitions etc., making

rectilinear stepped profiles, cut outs for light fittings, A/C grills,

speakers, services etc etc. and including providing and fixing

necessary G.I./wooden frame supports for the above fixtures

and additional suspenders to hang the same independently.

G.I. frame to consist of proprietary supplied frames and as per

manufacturers recommendations, suspended from RCC slab

with dash fasteners / or anchored to exposed reinforcement of

structural slab by means of GI proprietary angles. Gypsum

board fixed with proprietary supplied fixing devices and

including top coat and finished to receive paint. All complete

including 100/150 wide return air slits & A/C boxing wherever

indicated/required.

SqM 200

Estimate 13 of 49


Rate (INR)

Bill of Quantities


Amount in figures

(INR)S.NO

DESCRIPTIONUNIT

Quantity

2.00 Designer Ceiling

DESIGNER CEILING: Of overall specification as per item no H 1

above but in stepped / designed profile as per details in

specified areas formed of pre-cast slabs/ cast in situ POP

stepped profiles including coves at various levels, including cut

outs for light fixtures, speakers, services etc as indicated in

reflected ceiling plans, all to approval of Architects.

SqM 200

3.00 Tile Grid Ceiling

MINERAL FIBRE CEILING Providing and Fixing mineral fiber

ceiling consisting of tiles and grids as follows:

1. Armstrong Fine Fissured or equivalent, 600 x 600 mm

nominal size range or equivalent with tegular edge.

2. Ceiling grid to be of hot dip galvanized steel system, power

coated white finish, including main runners, cross tees and wall

angles. Profile to be used is 15 mm wide.

3. Main runners to be spaced at 1200mm centers, fixed to

soffit by approved hangers at 1200 mm distance. First and last

hangers should not be at a distance of more than 450 mm

from the adjacent wall. 600 x 600 mm module to be formed by

fixing 600 mm cross tee between center of 1200 mm cross

tees. Wall angels to be secured to wall at 450mm centers.

SqM 2000

4.00 Floating Ceiling

FLOATING CEILING: Specification same as H 1 above but

providing, fabricating and fixing floating gypsum ceiling instead

of Gypsum board, made of 12mm thick commercial ply,

including making groove, necessary hardware, adhesive etc.

complete. Ceiling to be suspended from the structural slab

above with 50mm dia SS pipes/supports as required.

SqM 50

5.00 Access Panels

LAMINATED ACCESS PANEL: P&F 12 mm thick commercial

board size 300 x 300 faced with 1mm thick laminate, to G.I.

framing perfect in level to form access panel for AC ducts.

Nos 10.00

J LOOSE FURNITURE

Estimate 14 of 49


Rate (INR)

Bill of Quantities


Amount in figures

(INR)S.NO

DESCRIPTIONUNIT

Quantity

1.00 Reception TableRECEPTION DESK: Supply and installing

reception desk as per architects design. Reception desk to

consist of front and side units along with storage units. Front

unit to have additional horizontal surface at ht. 1050 mm

above the floor level. Entire table to be made of 19 mm thk.

commercial board. Front and Sides of Table to be finished in 10

mm thk. Colour back of approved colour to Architects approval.

Projected front to be finished in 12 mm Thk. MDF as per detail

in approved colour. Table to have wire management detail, if

required. O/A dimensions 1800 x 750 X 1050 MM. One nos.

fixed drawer units to consist of two stationary Drawers and one

file drawer. All drawers to have 1 mm thk. laminate finished on

all sides formed of 19 mm thick board. Refer drawing number

DT- 311

Nos 1.00

Total Bill No. 1

Bill No. 2 : HVAC WORKS

1.1 CASSETTE TYPE FCU's

Supply, installation testing and commissioning of cassette

type fan coil units, each complete with blower,single

phase electric motor ,prefilters multirow deep chiller

water cooling coil , insulated drain pan & drain pump

complete with power/control wiring between power source

& FCU / between thermostat and the FCU/control valve.

a 2.95 TR Nos 6.00

b 1.6 TR Nos 4.00

c 1.0 TR Nos 2.00

2 AIR DISTRIBUTION

Estimate 15 of 49


Rate (INR)

Bill of Quantities


Amount in figures

(INR)S.NO

DESCRIPTIONUNIT

Quantity

2.1 Supply ,installation and Testing of factory fabricated

galvanised sheet metal ducts including elbows ,turning

vanes ,neoprene /PVC fire retardant gaskets, threaded

rods,supports/hangers etc.in accordance with the approved

shop drawing and specifications.The canvass connection

made of fire retardant double canvass cloth between AHU's

and ducts should be included in the cost of ducting.

Including designing of ducting for the office area as

required.

a 26 Gauge 0-750mm ( C & SS Cleats ) Sqmt 1100.00

b 26 Gauge 751-1000mm (TDS Flanges) Sqmt 350.00

c 24 Gauge 1001-1500mm (TDS Flanges) Sqmt 400.00

d 22 Gauge 1501-1800mm (TDS Flanges) Sqmt 100.00

e 20 Gauge 1801-2100mm (TDS Flanges) Sqmt 100.00

2.2 Supply ,installation and Testing of site fabricated

galvanised sheet metal ducts including elbows ,turning

vanes ,neoprene /PVC fire retardant gaskets, threaded

rods,supports/hangers etc.in accordance with the approved

shop drawing and specifications.The canvass connection

made of fire retardant double canvass cloth between AHU's

and ducts should be included in the cost of ducting.

Including designing of ducting for the office area as

required.

a 24 Gauge 0-750mm (GI Flanges) Sqmt 100.00

b 22 Gauge 751-1500mm (25x25x3mm MS angle flange ) Sqmt 20.00

c 20 Gauge 1501-2250mm (40x40x5mm MS angle flange ) Sqmt 20.00

d 18 Gauge > 2250 mm (50x50x5mm MS angle flange ) Sqmt 50.00

2.3 Supply, installation ,testing and balancing of one way blow

linear supply cum return air grills as per approved shop

drawings and specifications. The grills shall be of approved

colour and shade.

Powder coated aluminium grills of extruded sections with

integral flanges on both sides and ends as required.

1. 100/150/200 mm high

Sqmt 45

Estimate 16 of 49


Rate (INR)

Bill of Quantities


Amount in figures

(INR)S.NO

DESCRIPTIONUNIT

Quantity

2.4 Supply, installation ,testing and balancing of square supply

air diffusers as per the approved shop drawings and

specifications. Each diffuser shall be equipped with fixed

air distribution grid, removable core for proper balancing of

air distribution system

a. Powder coated extruded aluminium diffusers of

approved colour and shade.

Sqmt 5

2.5 Supply, installation ,testing and balancing of square supply

plate type air diffusers as per the approved shop drawings

and specifications. Each diffuser shall be equipped with

fixed air distribution grid, removable core for proper

balancing of air distribution system

a. Powder coated extruded aluminium diffusers of

approved colour and shade.

Sqmt 45

2.6 Supply , installation and testing of multi blade type louver

dampers of steel sheet for ducts collars to be provided with

suitable links, levers and quadrants for manual control of

volume of air flow and for proper balancing of the air

distributions system

Sqmt 18

2.7 Supply, installation and testing of multi blade box type steel

sheet dampers for ducts to be provided with suitable links,

levers and quadrants for manual control of volume of air

flow and for proper balancing of the air distribution system .

Sqmt 15

2.8 Supply, installation and testing of Flexible duct connection

to supply air diffuser comprising of aluminium plenums

having adaptor to connect 200/250/300 mm dia flexible

duct made of aluminium foil both inside and outside

encapsulating a steel wire helix (UL 181 class1) duly

insulated with 16 kg/sqm density resin bonded fibre glass

and complete with volume control dampers .

a. 450 x 450 x 250 mm ht plenum Nos 110.00

b.175 mm wide x 300 mm ht plenum . Rm 5.00

Estimate 17 of 49


Rate (INR)

Bill of Quantities


Amount in figures

(INR)S.NO

DESCRIPTIONUNIT

Quantity

c. Flexible duct of150 mm dia with fasteners on both sides Rm 10.00

d. Flexible duct of200 mm dia with fasteners on both sides Rm 5.00

e. Flexible duct of 250 mm dia with fasteners on both sides Rm 125.00

f. Flexible duct of 300 mm dia with fasteners on both sides Rm 10.00

2.9 Supply , installation and testing of multi slot diffuser duly

powdered coated.

a. 3 slot

Rm 50.00

3 INSULATION

3.1 Supply and application of internal acoustic insulation of

ducting with 25mm thick resinbonded fibreglass as per the

specifications and drawings

Sqmt 180.00

3.2 Supply and application of external thermal insulation of

ducting with 9mm thick UV resistant film laminated

polyethylene foam as per the specifications and drawings

Sqmt 2200.00

4 CHILLED WATER PIPING

4.1 Providing, fixing in position and testing the following MS

"Heavy " pipes confirming to IS1239 , cut to required

lengths and installed with all flanged joints including fixing

in position the necessary fittings like elbows, tees and

reducers duly insulated with black UV resistant film faced

polyethylene pipe sections of 33 kg / cum density covered

with 26 Gauge aluminium cladding as per specs complete .

The cost shall include PVC blocks , MS epoxy coated

channel frame work , U supports of 12 mm dia threaded

rods for fastening the pipes etc .

50 mm dia ( 25 mm thick insulation ) Rm 70.00




Estimate 18 of 49


Rate (INR)

Bill of Quantities


Amount in figures

(INR)S.NO

DESCRIPTIONUNIT

Quantity

4.2 Providing, fixing in position and testing of Butterfly valves

complete with necessary fitting like flanges, gasket and

hardware like nutbolts and washer duly insulated with black

UV resistant film faced polyethylene pipe sections of 33 kg

/ cum density covered with 26 Gauge aluminium cladding

as per specs . The insulation thickness shall be same as

specified for pipes above .

a 50 mm dia Nos 2.00

b 32 mm dia Nos 6.00

c 25 mm dia Nos 4.00

4.3 Providing, fixing in position and testing of Balancing valves

complete with necessary fitting like flanges, gasket and

hardware like nutbolts and washer duly insulated with black

UV resistant film faced polyethylene pipe sections of 33 kg

/ cum density covered with 26 Gauge aluminium cladding

as per specs .The insulation thickness shall be same as


a 50 mm dia Nos 1.00

b 25 mm dia Nos 9.00

4.4 Providing, fixing in position and testing of two way

modulating motorised valves complete with actuator,

temperature sensor and transformer and hardware like

nutbolts and washer duly insulated with black UV resistant

film faced polyethylene pipe sections of 33 kg / cum

density covered with 26 Gauge aluminium cladding as per

specs. The insulation thickness shall be same as specified

for pipes above .

25 mm dia

Nos 2.00

Estimate 19 of 49


Rate (INR)

Bill of Quantities


Amount in figures

(INR)S.NO

DESCRIPTIONUNIT

Quantity

4.5 Providing, fixing in position and testing of set of ball valves

(one with strainer and one without strainer ) complete with

necessary fittings like flanges, gasket and hardware like nut

bolts and washer duly insulated with black UV resistant film

faced polyethylene pipe sections of 33 kg / cum density

covered with 26 Gauge aluminium cladding as per specs

.The insulation thickness shall be same as specified for

pipes above . The insulation thickness shall be same as


25mm

Nos 9.00

4.6 Proving and fixing of dial type thermometers- 100 mm dia Nos 2.00

4.7 Providing ,fixing and testing of 1/4 " BSP thread size test

point suitable for measurement of water pressure

Nos 8.00

4.8 Providing fixing, testing & commissioning of automatic air

purge valves .

Nos 2.00

4.9 Providing and fixing of dial type pressure guages - 100

mm dia with adaptor & needle attachment .

Nos 2.00

5 CONTROLS

5.1 Supply, installation,testing & commissioning of existing sequential controller to run the split units on equal run hour basis keeping 1 unit as standby while running 1 unit complete with wiring between the indoor unit and controller etc .Nos. 3.00

5.2 Supply, installation,testing & commissioning of existing sequential controller to run the split units on equal run hour basis keeping 1 unit as standby while running 2 units complete with wiring between the indoor unit and controller etc .Nos. 1.00

6 Supply & installation of GI(Medium class) drainage pipes

conforming to IS1239 including all necessary fittings like

bends, tees etc.,duly insulated with

9mm thick nitrile rubber /Polyethylene insulation pipe

section & covered with 26 Gauge aluminium cladding,

connections with existing main drainage downtakes &

proper hanging/support arrangement with MS hangers/dash

fasteners(in case drainage pipes are to be installed above

false ceiling) complete as per specifications/drawings and

as directed by Engineer-in-Charge

(a) 25mm dia Rm 300.00

(b) 32mm dia Rm 20.00

Estimate 20 of 49


Rate (INR)

Bill of Quantities


Amount in figures

(INR)S.NO

DESCRIPTIONUNIT

Quantity

(c) 40mm dia Rm 20.00

Total Bill No. 2

Bill No. 3 : ELECTRICAL WORKS

I. LIGHT AND SOCKET OUTLET POINT WIRING

Note:

The rates for point wiring for all the items shall include the

following :

a)The Point Wiring shall include the supply of wire & wiring of

light/outlets of any length from the distribution board via switch to

the point.

b) All the light fixtures, third pin of outlets, switch and outlet boxes

shall be earthed with PVC insulated FRLS copper conductor wire

of same size as phase wire

c) All the outlets on the workstations and 16 amp 6-pin outlets

shall be earthed with PVC insulated FRLS copper conductor wire

of same size as phase wire.

d) All the switch boxes, outlet and junction boxes shall be covered

with White Polycarbonate modular cover plate.

e) Painting of junction boxes .

f) Supply & installation of MS conduits and allied fittings in

walls/floors/slabs etc. during construction and/or in chases

including cutting chases and making good as necessary in the

case of concealed conduit work.

g) All accessories necessary to complete the wiring as specified.

h)Internal wiring between accessories.

i) Wherever flexible conduit are required GI flexible conduit of

suitable size shall be used with checknut.

j) The boxes for switches and sockets shall be of same make as

switches and sockets

Estimate 21 of 49


Rate (INR)

Bill of Quantities


Amount in figures

(INR)S.NO

DESCRIPTIONUNIT

Quantity

1) Wiring including termination for the following light points with 2 x

2.5 sq. mm PVC insulated FRLS copper conductor wires of

650/1100 Volts grade in concealed/exposed 16gauge MS

conduits as called for including providing 6 amp flush type

switches,anodized MS box for housing switches approved White

Polycarbonate modular cover plate for switch boxes and

earthing. All the circuit must be dressed with circuit identification

tags a. First point

controlled by one no. 6 amp switch.

Nos 380.00

2) Same as item No. 1 above but LOOP POINT i.e. wiring including

termination of point looped from first point with 2 x 1.5 sq. mm

PVC insulated FRLS copper conductor wire of 650/1100 volt

grade in concealed/exposed 16 gauge MS conduit and earthing

(controlling switch in item no. 1).

Nos 450.00


2.5 sq. mm PVC insulated FRLS copper conductor wires of

650/1100 Volts grade in concealed/exposed 16gauge MS

conduits as called for including providing 16 amp flush type

switches,anodized MS box for housing switches approved White

Polycarbonate modular cover plate for switch boxes and

earthing. All the circuit must be dressed with circuit identification

tags

Nos 95.00

a. First point controlled by one no. 16 amp switch.

4) Same as item No. 3 above but LOOP POINT i.e. wiring including

termination of point looped from first point with 2 x 2.5 sq. mm

PVC insulated FRLS copper conductor wire of 650/1100 volt

grade in concealed/exposed 16 gauge MS conduit and earthing

(controlling switch in item no. 3).

Nos 475.00


2.5 sq. mm PVC insulated copper conductor FRLS wires of

650/1100 Volts grade in concealed/exposed 16 gauge MS

conduits and controlled by 10 amp MCB, complete as required

including earthing with 1.5 sq. mm PVC insulated copper

conductor FRLS wire and as per specifications. (The cost of MCB

has been taken elsewhere in the tender).(For Emergency

Lighting). All the circuit must be dressed with circuit identification

tags

Nos 10.00

a. One point controlled by 10A MCB.

Estimate 22 of 49


Rate (INR)

Bill of Quantities


Amount in figures

(INR)S.NO

DESCRIPTIONUNIT

Quantity

6) Same as item No. 5 above but LOOP POINT i.e. wiring of point

looped from first point with 2 x 1.5 sq. mm PVC insulated copper

conductor FRLS wire (controlling MCB in item no. 5) and earthing

with 1.5 sq. mm PVC insulated copper conductor FRLS earth

wire. (For Emergency Lighting)

Nos 50.00

7) Wiring including termination for 6 amp socket outlet point with 2 x

1.5 sq. mm PVC insulated FRLS copper conductor wires in

concealed/exposed 16gauge MS conduits or existing raceways

including providing 6 amp switch,3 pin 6A shuttered

socket,anodised MS box for housing switches sockets, approved

White Polycarbonate modular cover plate and earthing. (Looped

to lighting circuit as shown in drawing). All the circuit must be

dressed with circuit identification tags

Nos 10.00

8) Wiring including termination for the following configuration of

outlets for workstations with 3 core x 2.5 sq.mm. Copper

conductor ,PVC insulated PVC sheathed FRLS wires of

650/1100V grade in existing conduit/raceway including supplying

and fixing following numbers socket and switch housed in

anodised MS box with approved White polycarbonate modular

cover plate as required.NOTE :- Colour coding shall be strictly

followed for wiring. For Raw in one circuit maximum six

workstations shall be looped. For UPS in one circuit maximum

three workstations shall be looped. All the circuit must dressed

with circuit identification tags

a) 3 Nos. 6A, round pin outlets controlled by 1 No. 6A switch. (UPS

power at W/S)

Set 60.00

b) 2 Nos. 6A, round pin outlets controlled by 1 No. 6A switch. (UPS

power at W/S)

Set 280.00

c) 1 No. 6A, round pin outlets controlled by 1 No. 6A switch. (UPS

power)

Set 42.00

d) 1 No. 6A, round pin outlets controlled by 1 No. 6A switch. (Raw

power at W/S)

Set 400.00

e) 1 No. 13A, Universal outlets controlled by 1 No. 16A switch.

(Raw power)

Set 1.00

Estimate 23 of 49


Rate (INR)

Bill of Quantities


Amount in figures

(INR)S.NO

DESCRIPTIONUNIT

Quantity

9) Wiring including termination for 16 amp power socket outlet

points with 2 x 6 sq. mm PVC insulated FRLS copper conductor

wires for the first socket outlet and 2 x 4 sq. mm PVC insulated

FRLS copper conductor wires for the second outlet of 650/1100

Volts grade in concealed/exposed 16 gauge MS conduits or

existing raceway as called for including providing 16 amp flush

type combined 6 pin shuttered sockets and switches,

anodisedMS outlet boxes for 16 A 6 pin sockets and

switches,approved White Polycarbonate modular cover plate

and earthing.(The item is for set of two outlets looped together as

explained above ) All the circuit must dressed with circuit

identification tags

Set 40.00

10) Wiring including termination for 16 amp power socket outlet point

with 2 x 4 sq. mm PVC insulated FRLS copper conductor wire of

650/1100 Volts grade in concealed/exposed 16 gauge MS

conduits or in exisiting racewayincluding providing 16 amp flush

type combined 6 pin shuttered socket and switch,anodised MS

boxes for 16 amp 6 pin socket and switch, approved White

Polycarbonate modular cover plate and earthing. (Only one

outlet shall be connected to each circuit). All the circuit must

dressed with circuit identification tags

Nos 170

11) Supplying and fixing of 20 amp 3-pin 1-phase industrial socket

outlet including supplying boxes of suitable size,20 amp DP MCB

and a plug top, complete as required and as per specifications.

(For TP Room)

Nos 12

12) Supplying and fixing of 32 amp 3-pin 1-phase industrial socket

outlet including supplying boxes of suitable size,32 amp DP MCB

and a plug top, complete as required and as per specifications.

(For Server Room)

Nos 20

13) Supply,installation,testing and commissioning of 100 A TP MCCB,

with heavy duty solid neutral link in a sheet steel enclosure with

required arrangement for incoming and outgoing cable complete

as required.(For 30 KVA UPS for Server room)

Nos 4

14) Supplying and fixing in position of the following sizes of

exposed/concealed 16gauge MS conduit including all accessories

complete as required and as per specifications.

a. 25 mm dia MS conduit RM 1400

Estimate 24 of 49


Rate (INR)

Bill of Quantities


Amount in figures

(INR)S.NO

DESCRIPTIONUNIT

Quantity

15) Supplying , drawing,termination of the following size of FRLS PVC

insulated copper conductor wires 650/1100 V grade in existing

conduits, complete as required and as per specifications.

a. 3 x 6 sq. mm sq. mm PVC insulated copper conductor earth wire. RM 400

II. CONDUITS AND MS POWDER COATED CHANNELS FOR

STRUCTURED CABLING

1) Supplying and fixing in position MS anodised box for data/voice

outlet suitable for fixing of RJ 45 jack complete as required.(For

Data/voice outlets & Detectors above False ceiling)

Nos 580

2) Supplying and fixing in position following sizes of 16 gauge MS

conduits including providing all accessories concealed/ exposed

as required.

a. 25 mm dia MS conduit (For Data/Voice wiring) (16 GAUGE)

complete with all fixing accessories

RM 1500

b. 32 mm dia MS conduit (For Data/Voice wiring) (16 GAUGE)

complete with all fixing accessories

RM 50

3) Supply and fixing of following sizes of MS Powder Coated

channel colour coded Orange for power, Blue for Data ,14 gauge,

with openable cover and all accessories as required for fixing on

wall/column complete as required including providing junction

boxes,bends and tees as required.

a 300 mm x 50 mm RM 30

Estimate 25 of 49


Rate (INR)

Bill of Quantities


Amount in figures

(INR)S.NO

DESCRIPTIONUNIT

Quantity


channels, 14 gauge, with openable cover with all accessories as

required including stainless steel covered junction boxes,colour

coded with orange colour for power and blue colour , laid in floor

including marking the routing,getting it approved,cutting the

floor,filling and plastering after laying the raceway,grouting the

raceway to the floor,sealing of raceway cover,joints and junction

boxes complete as required. Required junction boxes will be

provided for smooth pulling of structured and power cabling.It will

be the responsibility of the contractor to coordinate with

structured cabling contractor for laying of cable.

a. 300mm x 40mm (3 mm thick cover) RM 480.00

b 200mm x 40mm (3 mm thick cover) RM 165.00

c 150mm x 40mm (2 mm thick cover) RM 260.00

d 100mm x 40mm (2 mm thick cover) RM 475.00

e. 300mm x 40mm (3 mm thick Stainless steel Cover) RM 110.00


channels 14 gauge, with openable cover, with all accessories as

required including junction boxes, orange colour for power and

blue colour for data, suspended from the ceiling including

providing suspension arrangement with all accessories in an

approved manner complete as required. Required junction boxes

will be provided for smooth pulling of structured and power

cabling.It will be the responsibility of the contractor to coordinate

with structured cabling contractor for laying of cable.

a. 300mm x 50mm RM 190.00

b. 100mm x 50mm RM 30.00

6) Supply and fixing in position MS anodised box for T.V. outlet

including white poly carbonate modular cover plate and co-axial

type T.V. socket outlet complete as required.

Nos 5.00

7) Supply , drawing,termination of RG-6 co-axial cable for TV in

existing conduit complete as required.

RM 300.00

Estimate 26 of 49


Rate (INR)

Bill of Quantities


Amount in figures

(INR)S.NO

DESCRIPTIONUNIT

Quantity

8) Providing and fixing in position following sizes of MS conduits

including providing all accessories concealed/ exposed as

required along with G.I. pull wire,14 SWG

450.00

a) 25 mm dia MS conduit RM

III. SUPPLY OF MDB,UMDB & INPUT PANEL

1. MDB’S / UMDB & INPUT PANEL

Design, manufacture, testing at works & supply of 2 mm thick MS

sheet steel fabricated cubicle type Panel dust and vermin proof

complete with hinged and lockable doors . All the panels shall be

floor mounted and dead front construction complete with

interconnections by copper tapes/ wires and painting.

Each MCCB outgoing feeder shall be provided with one no. ON

indication lamp.All MCB,s shall be C curve type, except UMDB in

which MCB shall be D curve type.

a. MDB - 1

Incoming

1 No. 160A FP MCCB, 25 KA service breaking capacity, trip

setting as required

Indicating Panel

The Indicating panel of incomer shall be provided with the

following :

i. Multifunction meter with CT's

ii. 3 Nos. phase indicating lamps; backed up with MCB.

Bus Bar

1 No. 200 amp TPN Al Bus bar of suitable length with current

density of 1.3 sq.mm/amp.

Outgoing

All MCCB outgoing feeders shall be provided with ON

indication lamp.i. 2 Nos. 100 amp TP MCCB of 25 KA service breaking capacity &

Trip setting as required ,with heavy duty solid neutral link

including Power Factor Meter and CT.

Set

ii. 1 No. 100 amp TP MCCB of 25 KA service breaking capacity &


Set

iii. 3 Nos. 63 A FP MCB,10 KA breaking capacity. Set

iv. 1 No. 40 A FP MCB,10 KA breaking capacity. Set

Estimate 27 of 49


Rate (INR)

Bill of Quantities


Amount in figures

(INR)S.NO

DESCRIPTIONUNIT

Quantity

MDB - 1 described as above Set 2

b. MDB - 2

Incoming

1 No. 160A FP MCCB, 25 KA service breaking capacity, trip

setting as required

Indicating Panel

The Indicating panel of incomer shall be provided with the

following :

i. Multifunction meter with CT's


Bus Bar

1 No. 200 amp TPN Al Bus bar of suitable length with current

density of 1.3 sq.mm/amp.

Outgoing

All MCCB outgoing feeders shall be provided with ON

indication lamp.i. 2 Nos. 100 amp TP MCCB of 25 KA service breaking capacity &


including Power Factor Meter and CT.

Set

ii. 1 No. 100 amp TP MCCB of 25 KA service breaking capacity &


Set

iii. 3 Nos. 63 A FP MCB,10 KA breaking capacity. Set

iv. 1 No. 40 A FP MCB,10 KA breaking capacity. Set

MDB - 2 described as above Set 2

c. UMDB - 1

Incoming

2 No. 100 amp TP MCCB 25 KA service breaking capacity and

Trip setting as required with isolable heavy duty solid neutral

link of double the rating as phase.

Indicating Panel

The Indicating panel of each incomer shall be provided with the

following :

i. Digital ammeter ,CT's , Digital Voltmeter


Bus Bar

1 No. 100 amp TPN Copper Bus bar of suitable length with

current density of 1.0 sq.mm/amp with neutral bus bar double size

of phase bus bar.

Outgoing

Estimate 28 of 49


Rate (INR)

Bill of Quantities


Amount in figures

(INR)S.NO

DESCRIPTIONUNIT

Quantity

7 Nos. 63 A FP MCB,10 KA breaking capacity., D curve

UMDB - 1 described as above. Set 2.00

IV. INSTALLATION OF PANELS; SUPPLY AND INSTALLATION

OF DB, CABLES AND EARTHING

1) Receiving, storing properly, installation, testing and

commissioning of following panels complete as required.

a. MDB's Set 4.00

b. UMDB Set 2.00

2) Supplying, installing in position, testing and commissioning of the

following Distribution Boards made of 18 gauge powder coated

MS sheet steel , wall mounted/fully recessed in wall, indoor

industrial type, with dust & vermin proof, hinged and lockable

doors,double door design, complete with inter connecting wires of

proper guage, aluminium coated copper thimbles and with the

circuit identification tags. Incomer MCB to each ELCB along with

earthing terminal. The DB shall be suitable for taking

cable/conduit as incoming/outgoing. All MCB to be C Curve

unless specified otherwise & of 10 KA breaking capacity.

a. 12 way TPN DB with 30 Nos of 10/20 amps SP MCB's i.e. 10

Nos. of 10/20 amp SP MCB's arranged in 3 rows arranged in 3

tier one above other and controlled by 1 No. 63 amp FP isolator

and neutral link. Each row of MCB’s shall be provided with 40

amp DP ELCB of 100 mA sensitivity. (For Pow.)

Nos 6.00

b. 10 way TPN DB with 24 Nos of 10/20 amps SP MCB's i.e. 6 Nos.

of 10/20 amp SP MCB's arranged in 3 rows arranged in 3 tier one

above other and controlled by 1 No. 63 amp FP isolator and

neutral link. Each row of MCB’s shall be provided with 40 amp DP

ELCB of 100 mA sensitivity. (For Lig.)

Nos 6.00

c. 12 way TPN DB with 30 Nos of 10/20 amps SP MCB's i.e. 10

Nos. of 10/20 amp SP MCB's arranged in 3 rows arranged in 3

tier one above other and controlled by 1 No. 63 amp FP isolator

and neutral link. Each row of MCB’s shall be provided with 40

amp DP ELCB of 100 mA sensitivity. All MCB to be D curve (For

UPS)

Nos 3.00

Estimate 29 of 49


Rate (INR)

Bill of Quantities


Amount in figures

(INR)S.NO

DESCRIPTIONUNIT

Quantity

d. 10 way TPN DB with 24 Nos of 10/20 amps SP MCB's i.e. 6 Nos.


above other and controlled by 1 No. 63 amp FP isolator and

neutral link. Each row of MCB’s shall be provided with 40 amp DP

ELCB of 100 mA sensitivity. All MCB to be D curve (For UPS)

Nos 6.00

e. 4 way TPN DB with 12 Nos of 10/20 amps SP MCB's i.e. 4 Nos.


above other and controlled by 1 No. 63 amp FP MCB and neutral

link. All MCB to be D curve. ( For Server Room)

Nos 3.00

f. 4 way TPN DB with 12 Nos of 10/20 amps SP MCB's i.e. 4 Nos.



link. All MCB to be D curve. ( For TP Room)

Nos 3.00

g. 6 way TPN DB with 12 Nos of 10/20 amps SP MCB's i.e. 4 Nos.



link. Each row of MCB’s shall be provided with 40 amp DP ELCB

of 100 mA sensitivity. (For Emergency)

Nos 3.00

5) Supply and fixing in position the following insulated wires

including providing all fixing accessories and effecting proper

connections.

a. 6 sq. mm. dia pvc insulated copper conductor wire. RM 350.00

6) Supplying, unloading, storing , laying, testing and commissioning

of following sizes PVC insulated (Heavy duty) Copper conductor

cables suitable for working voltage upto and including 1100

Volts , laid and tied on existing overhead cable trays; or laid and

tied over MS supports in masonry trenches including providing

MS supports and clamps for fixing to supports in an approved

manner complete as required and as per specifications.Circuit

identificarion tag should be attached with the concerned cable

alongwith the test report of following sizes of cable to be

submitted by the contractor at the time of delivery of material at

site

a. Single Core 35 sq. mm. cable, armoured RM 1400.00

b. Single Core 35 sq.mm. cable unarmoured RM 750.00

c. Single Core 25 sq.mm. cable unarmoured RM 800.00

Estimate 30 of 49


Rate (INR)

Bill of Quantities


Amount in figures

(INR)S.NO

DESCRIPTIONUNIT

Quantity

7) Termination of the following sizes of PVC insulated Copper

conductor cable including providing terminal lugs,single

compression glands crimping the joints,providing insulation tape,

effecting terminal connections to the equipment complete as

required.

a. Single Core 35 sq. mm. cable, armoured Nos. 36.00

b. Single Core 35 sq.mm. cable unarmoured Nos. 80.00

c. Single Core 25 sq.mm. cable unarmoured Nos. 36.00

8) Supplying, unloading, storing , laying, testing and commissioning

of following sizes of XLPE insulated (Heavy duty)

Aluminium/copper conductor armoured cables suitable for

working voltage upto and including 1100 Volts , laid and tied on

existing overhead cable trays; or laid and tied over MS supports

in masonry trenches including providing MS supports and clamps

for fixing to supports in an approved manner complete as required

and as per specifications.

a. 3.5 x 70 sq.mm.Aluminium Cable RM 250.00

b. 4 x 35 sq.mm.Aluminium Cable RM 350.00

c. 4 x 16 sq.mm. Copper Cable RM 600.00

d. 4 x 10 sq.mm.copper Cable RM 340.00

e. 4 x 6 sq.mm.copper Cable RM 180.00

f. 2 x 6 sq.mm. copper Cable (For Dedicated earthing and body

earthing of DB's)

RM 800.00

9) Termination of the following sizes of PVC insulated Aluminium

conductor cable including providing terminal lugs,single

compression gland , crimping the joints ,providing insulation

tape,effecting terminal connections to the equipment complete as

required

a. 3.5 x 70 sq.mm.Aluminium Cable Nos. 12.00

b. 4 x 35 sq.mm.Aluminium Cable Nos. 12.00

c. 4 x 16 sq.mm. Copper Cable Nos. 28.00

d. 4 x 10 sq.mm.copper Cable Nos. 12.00

e. 4 x 6 sq.mm.copper Cable Nos. 6.00

Estimate 31 of 49


Rate (INR)

Bill of Quantities


Amount in figures

(INR)S.NO

DESCRIPTIONUNIT

Quantity

f.. 2 x 6 sq.mm. copper Cable (For Dedicated earthing and body

earthing of DB's)

Nos. 20.00

12) Supply,installation,testing and commissioning of Earth box made

of 2mm thick MS painted ,with a glass cover and having 25 x 6

mm Cu strip with insulators complete as required.

Set 5.00

13) Supply, laying in position & proper connection by welding/bolting

or brazing for the following GI tape/wires including providing all

fixing accessories and effecting proper connections.

RM 400.00

a. 25 x 6 mm GI tape

14) Supply and installation of following sizes of MS perforated type

cable trays with stove enamel paint of approved colour and

necessary bends, tees, reducer couplers, dashfastners,GI nuts

bolts including cutting,bending, drilling, bolting required

suspension arrangement fabricated from steel etc.complete as

per specifications and as approved by Engineer - in - charge. The

suspension of MS cable tray, only GI or SS round rods with

ceiling anchoring facility should be used.

i 750 mm wide, 40 mm high (2 mm thick) RM 10.00

ii 600 mm wide, 40 mm high (2 mm thick) RM 50.00

iii 450 mm wide, 40 mm high (2 mm thick) RM 80.00

iv 300 mm wide, 40 mm high (2 mm thick) RM 60.00

v 150mm wide, 40 mm high (2 mm thick) RM 20.00

vi 450 mm wide, 100 mm high (Server Room) RM 20.00

vii 300 mm wide, 100 mm high (Server Room) RM 10.00

V. FIXING OF LIGHTING FIXTURES.

Estimate 32 of 49


Rate (INR)

Bill of Quantities


Amount in figures

(INR)S.NO

DESCRIPTIONUNIT

Quantity

Note : The rates for fixing of lighting fixtures shall include all

fixing accessories that are required to make the installation

complete in all respects including the following :- a). Providing

connecting wires and channel support wherever required. b).

Internal wiring between accessories. c). Self interlocking

connector blocks for connecting the wires from fixtures to the

points. d) Earthing of fixtures with 1.5 sq. mm. PVC insulated

copper conductor wire. e) Approved colour powder coated down

rods, clamps and other components and fixing accessories

wherever required. f) Testing of fixtures before Installation. g)

Identification tags with a distance not more 3 meters to be use for

circuit identification

1) Receiving, fixing in position, effecting proper connections, testing

and commissioning of 2x2 LED Light fixtures recess mounted on

ceiling or suspended from exisitng raceway/slab with chains with

all fixing accessories as required.

Nos 20.00


and commissioning of 2x2 LED Light fixtures fixed recessed in

ceiling with chains hung from slab with all fixing accessories as

required, along with providing GI flexible conduit from junction box

at slab level to fixture on the false ceiling.

Nos 290.00


and commissioning of LED downlighter fixed recessed as

required and with all accessories, along with providing GI flexible

conduit from junction box at slab level to fixture on the false

ceiling.

Nos 500.00

4) Installation,testing and commissioning of EXIT light Prolite make

self contained 6W luminaire complete with flush mounting frame

and battery and with label EXIT/RIGHT/LEFT/UP/DOWN as

required..

Nos. 20.00


and commissioning of Wall Bracket Fan complete as required.

Nos 25.00

VI. SUPPLY OF LIGHTING FIXTURES

Estimate 33 of 49


Rate (INR)

Bill of Quantities


Amount in figures

(INR)S.NO

DESCRIPTIONUNIT

Quantity

NOTE: a) The fixtures shall be suitable for single phase, 50

cycles, 230 Volts, A.C. supply system. b) All fixtures shall be

factory wired with copper conductor wires. c) All the samples shall

be submitted within one week of the issue of work order, for

approval from the Architect. d) Any lost & damage during

transportation shall be in the scope of electrical contractor till final

testing, commissioning & handing over of work.

1) Supply, unloading storing at site, installation testing and

commissioning of the following LED fixtures with all accessories.

a. LED Light Panel recess mounted 2x2 tile in CRCA housing with

full opal fiffuser 36 Watt with all accessaries of Philips/ bajaj/

orient

Nos 310.00

d. Cove light LED strip with all accessories i/c installation RM 500.00

2) Supply, unloading storing at site, installation testing and

commissioning of the following the following LED light fixtures

with all accessories of Philips/ bajaj/ orient

a. LED Downlighter recess mounted, aluminium die cast housing

slim edge panel, 20 Watt (approved make : Philips/ bajaj/ orient)

Nos 500.00

3) Supply, unloading & storing, installation testing and

commissioning of EXIT light Prolite make self contained 6W

luminaire complete with flush mounting frame ,sign label and

battery and with label EXIT/RIGHT/LEFT/UP/DOWN as

required.approved make : Philips/ bajaj/ orient

Nos. 20.00

4) Supply, unloading, storing at site of air circulator 450mm sweep

oscillating type wall mounting 1440 RPM without speed regulator,

overheat protection unit, totally enclosed frame proof motor

suitable for 230/250Volts single phase, 50 cycles A.C supply with

one metre of 3 core lead wire and with moisture proof treatment

to winding and with "E" class insulation and marking Sr. No. and

date of erection. (Make : Bajaj / Crompton Greaves)

Nos 25.00

VII. CONDUIT AND WIRING FOR INTELLIGENT FIRE DETECTION

AND ALARM SYSTEM & ACCESS CONTROL SYSTEM

Estimate 34 of 49


Rate (INR)

Bill of Quantities


Amount in figures

(INR)S.NO

DESCRIPTIONUNIT

Quantity

1) Supply, installation, testing & commissioning with proper

connection & temination of 2 core 1.5 sq mm mineral insulated

copper conductor (MICC) Fire survival cables of CWZ type which

can withstand 1100 / 950 deg C for 3 hrs 550 V grade as per

relevant IEC / International code includding cost of crimped

termination etc. in existing conduit.

RM 1800.00

2) Supply and laying in position the following sizes of 16 SWG M.S.

conduits including providing all accessories complete as required.

(For Fire Detection)

a. 25 mm dia conduit RM 1700.00

b. 25 mm dia GI flexible conduit RM 100.00

3) Supplying, drawing, connecting, testing & commissioning of 2 x

1.5 sq. mm. stranded copper conductor, pvc insulated FRLS wire

for CCTV power/Access Door in existing conduit/raceway.

RM 1800.00

4) Supply , drawing,termination of RG-59 CCTV coaxial cable for

CCTV in existing conduit/raceway complete as required.

RM 1100.00

5) Supplying, drawing, connecting, testing & commissioning of 8

core, 1.0 sq. mm. stranded copper conductor, pvc insulated PVC

sheathed, shielded FRLS wire in existing conduit.

RM 1800.00

6) Providing and fixing in position following sizes of MS conduits

including providing all accessories concealed/ exposed as

required along with G.I. pull wire.

RM

a) 25 mm dia MS conduit (For Access Control & CCTV) (16

GAUGE)

RM 2500.00

Total Bill No. 3

Bill No. 4 :Fire Fighting System/Works

1.01 Providing, fixing, testing & commissioning of 15mm dia. Chrome

finished sprinkler head with quartz bulb, set to operate at 68°C,

complete as per given specifications. (UL/FM Approved)

(Make :- TYCO/VIKING)

Each 350.00

a) Standard Pendent/Upright type in brass/chrome finish.

1.02 Extra for providing and fixing white powder coated Rosette. Each 350.00

Estimate 35 of 49


Rate (INR)

Bill of Quantities


Amount in figures

(INR)S.NO

DESCRIPTIONUNIT

Quantity

1.03 Providing, fixing, jointing and testing of Mild steel black pipe (IS:

1239 Part-1) heavy class including cutting, welding/screwing etc.

and providing all fittings viz. flanges, bends, tees, elbow,

reducers, etc. including the cost of structural work for supports

fabricated from standard sections (of required size and thickness)

e.g. galvanised M.S. rods, angles channels, slotted angle, etc.,

cutting to sizes, drilling welding fixing to insert plates, including

painting over a coat of primer, cutting holes and chases in brick

or RCC walls/slabs and making good the same to the approval

of engineer/consultant complete including painting with one coat

of primer and two or more coats of enamel paint of approved

make and shade including steel work. Note : Pipes upto and 50

mm dia shall be threaded joints, above 50mm shall be welded

joints. (Make:-Jindal Hissar/Ghaziabad)

a) 150 mm dia Metre 25.00

b) 100 mm dia Metre 130.00

c) 80 mm dia Metre 75.00

d) 65 mm dia Metre 45.00

e) 50 mm dia Metre 50.00

f) 40 mm dia Metre 125.00

g) 32 mm dia Metre 150.00

h) 25 mm dia Metre 900.00

1.04 Providing & fixing15 mm dia screwed jointed pipe with fittings

using SS flexible pipe UL approved including threaded or

weldable GI fitting i.e unions ,bends, elbows, tees etc(Make:-

Eversave)

a) 1500mm length Each 100.00

b) 1000mm length Each 150.00

c) 700mm length Each 50.00

1.05 ISI marked (IS:2878) Portable fire extinguisher, of 4.5 kg capacity

Carbon-dioxide type flat base including valve, discharge hose of

not less than 10 mm dia 1m long & complete in all respects

including initial fill with CO2 gas confirming to IS: 307-1966 filled

to a filling ratio of not more than 0.667of not more than 0.667and

wall suspension bracket.

Each 20.00

1.06 'ABC' stored pressure type Dry chemical powder (Mono-

Ammonium Phosphate) fire extinguisher with fixing hangers,

hose, brackets, screws to required size etc., complete as per

IS:14609.

Each 20.00

Estimate 36 of 49


Rate (INR)

Bill of Quantities


Amount in figures

(INR)S.NO

DESCRIPTIONUNIT

Quantity

Total Bill No. 4

Bill No. 5 : FDA System

S.NO Item Description Unit

I. SUPPLY & INSTALLATION OF INTELLIGENT FIRE

DETECTION AND ALARM SYSTEM1) Supply, installation, testing & Commissioning of Photo thermal

multicriteria intelligent addressable detector with standard base

etc.complete as required and as per specifications.

Nos 275.00

2) Supply, installation, testing & Commissioning of Photo thermal

multicriteria intelligent addressable detector with fault isolator

base etc. as required and as per specifications.

Nos 35.00

3) Supply, installation, testing & Commissioning of addressable

manual push button to initiate audio alarm with a breakable glass

cover/resettable , intelligent addressable type complete as

required.and as per specifications.

Nos 8.00

4) Supply, installation, testing & Commissioning of Fire Alarm

Hooter, (sound output of minimum 90 dB upto a distance of 10

feet) with strobe light of minimum 75 cd intensity with power

supply arrangement complete as required and suitable for

wall/ceiling mounting.and as per specifications.

Nos 6.00

5) Supply, installation, testing & Commissioning of addressable

monitor module complete as required.and as per specifications.

(For Sprinkler Flow Switch & Developer panel)

Set 10.00

6) Supply, installation, fixing, testing and commissioning of

addressable control module complete as required for control of

AHU's, Hooters ,output to PA system, for integration with Access

Control, output of Developer panel etc. complete as required.and

as per specifications.

Set 10.00

Estimate 37 of 49


Rate (INR)

Bill of Quantities


Amount in figures

(INR)S.NO

DESCRIPTIONUNIT

Quantity

7) Supply, installation, testing & Commissioning of micro processor

based 2 wire fault tolerant loop, 2 loop networkable type (each

loop accessing minimum 99 detectors and 99 modules ) fire

alarm/detection control panel. The panel shall be able to give

location of all fire/fault conditions of addressable units via the

address codes. Further, the panel must be able to automatically

switch ON /OFFrespective control module when ever any alarm

is triggered. The panel shall have rectifier, Loop cards, L C D unit

to indicate Fire/Fault Signal with address and analog output,

external/inbuilt printer to log all fire or fault events complete in all

respects.The panel shall have a built in power supply and battery

charger along with maintenance free 24 AH, 2 x 12 volt SMF

Lead acid batteries capable of running for a minimum of 8 hours

with battery charger complete as required.and as per

specifications. The panel shall have a facility to relay a pre-

recorded message to the PA system.

Set 1.00

Total Bill No. 5

Bill No. 6 : Access Control System

S.NO Item Description

I. ACCESS CONTROL SYSTEM

4) Dismentalling of existing Biomatric attendance system from

DIMTS office Kashmere Gate and fixing testing & commissioning

the same at DIMTS office at 8th Floor Shastripark.

LS 1.00

5) Supply, installation, testing & commissioning of single

Electromagnetic lock,600 lbs along with magnetic contact

complete as required.

Nos 6.00

6) Supply, installation, testing & commissioning of dual

Electromagnetic lock ,600 lbs alongwith magnetic contact


Nos 6.00

7) Supply, installation, testing & commissioning of Exit push button


Nos 2.00

Estimate 38 of 49


Rate (INR)

Bill of Quantities


Amount in figures

(INR)S.NO

DESCRIPTIONUNIT

Quantity

8) Supply, installation, testing & commissioning of Emergency exit

push button including break glass enclosure complete as

required.

Nos 8.00

Total Bill No. 6

Bill No. 7 : CCTV SystemI. C.C.T.V. SYSTEM

1) Supply of 2MP HD Dome Camera (20 mtr) day & night IR Filter

LED dome/box camera complete as required in mini dome shape

fixed type for mounting recessed in false ceiling or mounted on

wall complete as required.

Nos 20.00

2) Supply of 2MP HD Dome Camera (30 mtr) day & night IR Filter

LED dome/box camera complete as required in mini dome shape

fixed type for mounting recessed in false ceiling or mounted on

wall complete as required.

Nos 10.00

3) Supply of 32 channel colour Digital Video Mgmt system with 32

cameras inputs Built in multiplexer, Digital Video recorder, Video

motion Detection system, with external alarm inputs & outputs

,TCPIP network feature & server software, 2 x HDD slots for

future storage expansion, 1200 GB Hard Disk Drive to be able to

achieve recording of 30 days in SVHS quality @ 24 hour mode

complete as per required and as per specification.

Nos 1.00

4) Supply, installation, testing & commissioning of power supply 12V

20 Amp Power Supply complete as required.

Nos 2.00

5) Supply 6TB Surveillance HD Nos 2.00

6) installation, testing & commissioning of Complete CCTV Setup as

required.

Job 1.00

Total Bill No. 7

Bill No. 8 : PA System

S.No. Item Description Unit

I. PUBLIC ADDRESS SYSTEM

Estimate 39 of 49


Rate (INR)

Bill of Quantities


Amount in figures

(INR)S.NO

DESCRIPTIONUNIT

Quantity


connection & temination of Bosch Plena Voice Alarm Call Station

having gooseneck condenser microphone with zone Selection

Keys and an All-Call-Key, PTT Switch, selectable gain, speech

filter and limiter for improved intelligibility, LED indication for zone

selection, fault and emergency state

Nos 1.00


connection & temination of Bosch Plena Voice Alarm Controller

having features like announcement to 4 zones expandable to 60

zones, built in required booster amplifier(Bosch ), emergency

microphone on the front panel, 16 priority levels including

emergency, music to selected zones can be played, upto 255

messages can be stored in the internal 16MB flash ROM,

individual BGM volume control for each zone, Digital pre-recorded

messages can be merged, full system supervision.

Set 1.00

3 Supply, installation, testing & commissioning of Music Source-5

CD Carrousel auto changer.

Nos. 1.00

4) Amplifier

Supply, installation, testing & commissioning with proper

connection & temination of Bosch Plena Booster Amplifier

capable of delivering required Wattage RMS power output for all

speakers mentioned in BOQ item no.6, built-in fan for

temperature control, built in line matching transformer distortion

typically < 3% @1 KHz, S/N> 80 dB complete as required.

Nos 1


connection & temination of 19" equipment rack made out of

CRCA sheet to house all the control equipment.

Nos 1

6) Supply, installation, testing & commissioning, proper connection &

temination of complete speaker (6W) ceiling mounted type Bosch

.

Nos 120.00

7) Wiring including terminations of 2 core 40/.2 mm PVC insulated

twisted copper conductor wires in existing conduit/ trunking as

required.

RM 1800.00

8) Supply and laying in position the following sizes of 16 SWG M.S.

conduits including providing all accessories complete as required.

a) 25 mm dia MS conduit RM 1700.00

Estimate 40 of 49


Rate (INR)

Bill of Quantities


Amount in figures

(INR)S.NO

DESCRIPTIONUNIT

Quantity

b) 25 mm dia GI flexible pipe RM 50.00

Total Bill No. 8

Bill No. 9 : IT Networking System

IT NETWORKING / STRUCTURED CABLING

1) Supply & Installation of CAT 6 information outlets complying fully

or exceeding with category 6 connecting hardware specifications

for all pair combinations up to 250 MHz. Outlets shall use lead

frame technology. (Blue in Colour for Data) complete as required.

Nos. 250.00

2) Supply & Installation of CAT 6 information outlets complying fully

or exceeding with category 6 connecting hardware specifications

for all pair combinations up to 250 MHz. Outlets shall be use lead

frame technology. (Green in Colour for Voice) complete as

required.

Nos. 250.00

3) Supply & Installation of UK sloped shuttered Quard Face Plates

along with clearly printed labels and holders complete as

required.

Nos. 10.00

4) Supply & Installation of UK sloped shuttered Triplex Face Plates


required.

Nos. 220.00

5) Supply & Installation of UK sloped shuttered Dual Face Plates


required.

Nos. 15.00

6) Supply & Installation of UK sloped shuttered Singlex Face Plates


required.

Nos. 15.00

7) Supply & Installation of Cat 6 Mounting Cords 2 meter length for

the User End & Rack End Connectivity to the System, Both end

shall be RJ 45 with snagless boots. (Blue in colour for Data)


Nos. 250.00

8) Supply & Installation of Cat6- 4 Pair 23 AWG UTP Cable with

cross member pair seperator complete as required in existing

conduit

m 48000.00

Estimate 41 of 49


Rate (INR)

Bill of Quantities


Amount in figures

(INR)S.NO

DESCRIPTIONUNIT

Quantity

9) Supply & Installation of Cat 6 Patch Panels for accommodating 24

port termination and shall facilitate cross-connection and inter-

connection using modular patch cords and shall conform to EIA

standard, 19-inch relay rack mounting requirements. Patch Panel

shall come with preloaded information outlets of non PCB and

pyramid type using lead frame technology.Panel shall have label

holders and designation labels as part of the standard

device.Shall also come with rear cable management metallic tray

with velcro ties complete as required.

Nos. 20.00


the Patch Panel End Connectivity, Both end shall be RJ 45 with

snagless boots complete as required. (Green in Colour for Voice)

Nos. 250.00


the Patch Panel End Connectivity, Both end shall be RJ 45 with

snagless boots complete as required. (Blue in Colour for Data)

Nos. 250.00

12) Supply & installation of Cat3 25 Pair Multi Pair cable complete as

required.

RM 200.00

13) Supply & Installation MDF 100 Pair for voice connectivity


Nos. 2.00

14) Supply & Installation of Jumper wire Single pair complete as

required.

Nos. 25.00

15) Supply & Installation of Horizontal Wire Manager front, 1U panel

with metal grooves at the back, plastic snap on cover complete as

required.

Nos. 20.00

16 Supply & installation of 42U closed rack(800mm x 800mm) with

front glass door, rear steel door, castors, 4fans with fan tray,

vertical wire manager complete as required.

No. 2.00

Estimate 42 of 49


Rate (INR)

Bill of Quantities


Amount in figures

(INR)S.NO

DESCRIPTIONUNIT

Quantity

17 Documentation , testing certification including pentascanning &

project management complete as required. NOTES:- (i) All

products for structured cabling solution mentined above shall be

provided from the single manufacturer, (ii) System Integrator shall

provide the certification for total structured cabling from the

manufacturer for Life time warranty. , (iii) System integrator shall

provide all the necessary documentation comprising patching

details, labeling and network schematic, (iv) System integrator

shall also provide the floor layout with final node distribution

clearly marked on the layout. , (v) Make of Components shall be

as follows :- CAT-6 Outlets / CAT-6 Cable / Patch Cords / Patch

Panel :- Systimax/Siemon/AMP

LS 1

Total Bill No. 9

Bill No. 10 :UPS SYSTEM WORKS

XII. SUPPLY & INSTALLATION OF UPS

1) Supply,unloading, installation, testing & commissiong of micro

processor /DSP controlled 1 Numbers 40 KVA UPS operating in

parallel with future UPS redundant mode so that if any one UPS

fails the other one can take care of 100% load, IGBT based

rectifier to achieve THDI < 5% and input power factor of greater

than 0.95 at 50% loading. True Online Double Conversion (VFI as

per IEC 62040-3) UPS using PWM IGBT technology , 3 Phase

input and 3 phase 415 V output UPS system; and each

comprising of the following: a) 125% rated Rectifier cum charger

unit +100% rated Invertor, Integrated in UPS module, b)100%

rated External Galvanic isolation transformers of K-13

Delta/Zigzag type for isolation of input neutral with output neutral.

c)100% rated Inbuilt static switch at the invertor output + 2 Nos.

100% rated Inbuilt static switches at the static bypass line. d)

100% rated Inbuilt Maintenance Bypass. e) 100% rated moulded

case battery circuit breaker having Ithermal, Imagnetic and

Automatic U/V trip mechanics. e) Wnd backup time of

batteries.The Contractor shall arrange the load testing at his own

c

Set 1

2) Supplying, unloading,installing in position, testing and

commissioning of Lead Acid sealed maintenance free batteries

for 40 KVA UPS system , for providing 20 minutes backup to 40

KVA UPS for full load. The bank of batteries shall comprise

required Nos of Amarraja/Rocket make, batteries complete as

required.Battery sizing calculation are to be submitted for

approval

Set 1CustomerCustomerCustomerCustomerCustomerCustomer CustomerCustomerCustomerCustomerCustomerCustomerCustomerCustomer CustomerCustomerCustomerCustomerCustomerCustomerCustomerCustomer CustomerCustomerCustomerCustomerCustomerCustomerCustomerCustomerCustomerCustomerCustomerCustomer CustomerCustomerCustomerCustomerCustomerCustomerCustomerCustomer CustomerCustomerCustomerCustomer CustomerCustomerCustomerCustomer CustomerCustomerCustomerCustomerCustomerCustomerCustomerCustomerCustomerCustomer CustomerCustomerCustomerCustomerCustomerCustomerCustomerCustomerCustomerCustomer CustomerCustomerCustomerCustomerCustomerCustomerCustomerCustomer CustomerCustomerCustomerCustomerCustomerCustomerCustomerCustomer CustomerCustomerCustomerCustomerCustomerCustomerCustomerCustomerCustomerCustomerCustomerCustomer CustomerCustomerCustomerCustomerCustomerCustomerCustomerCustomer CustomerCustomerCustomerCustomer CustomerCustomerCustomerCustomer CustomerCustomerCustomerCustomerCustomerCustomerCustomerCustomerCustomerCustomer CustomerCustomerCustomerCustomerCustomerCustomerCustomerCustomerCustomerCustomer CustomerCustomerCustomerCustomerCustomerCustomerCustomerCustomer CustomerCustomerCustomerCustomerCustomerCustomerCustomerCustomer CustomerCustomerCustomerCustomerCustomerCustomerCustomerCustomerCustomerCustomerCustomerCustomer CustomerCustomerCustomerCustomerCustomerCustomerCustomerCustomer CustomerCustomerCustomerCustomer CustomerCustomerCustomerCustomer CustomerCustomerCustomerCustomerCustomerCustomerCustomerCustomerCustomerCustomer CustomerCustomerCustomerCustomer

Estimate 43 of 49


Rate (INR)

Bill of Quantities


Amount in figures

(INR)S.NO

DESCRIPTIONUNIT

Quantity

3) Supply,unloading, installation, testing & commissioning of

matching cabinet/open racks to house SMF batteries for 40 KVA

UPS system along with interconnecting links, MCCB etc.

complete as required & as per specifications.

Set 1

4) Supply, laying, testing & commissioning of flexible single core

copper cable of Finolex / Skyline/Grandlay/National make for

interconnections between UPS to UPS, UPS to batteries,

Isolation transformer to UPS complete as required for 40 KVA

UPS,including providing Battery circuit breakers as required.

Set 1

5) Supply,unloading, installation, testing & commissiong of micro

processor /DSP controlled 2 Numbers 30 KVA UPS operating in

parallel redundant mode so that if any one UPS fails the other one

can take care of 100% load, IGBT based rectifier to achieve

THDI < 5% and input power factor of greater than 0.95 at 50%

loading. True Online Double Conversion (VFI as per IEC 62040-3)

UPS using PWM IGBT technology , 3 Phase input and 3 phase

415 V output UPS system; and each comprising of the following :

a) 125% rated Rectifier cum charger unit +100% rated Invertor,

Integrated in UPS module. b) 100% rated External Galvanic

isolation transformers of K-13 Delta/Zigzag type for isolation of

input neutral with output neutral. c) 100% rated Inbuilt static

switch at the invertor output + 2 Nos. 100% rated Inbuilt static

switches at the static bypass line. d) 100% rated Inbuilt

Maintenance Bypass. e) 100% rated moulded case battery circuit

breaker having Ithermal, Imagnetic and Automatic U/V trip

mechanics. f) Web-enabled Monitoring and Management through

SNMP protocols for multi-OS environments.

Set 1

6) Supplying, unloading,installing in position, testing and

commissioning of Lead Acid sealed maintenance free batteries

for 30 KVA UPS system , for providing 20 minutes backup to 30

KVA UPS for full load. The bank of batteries shall comprise

required Nos of Amarraja/Rocket make, batteries complete as

required. Battery sizing calculation are to be submitted for

approval

Set 2.00

7) Supply,unloading, installation, testing & commissioning of

matching cabinet/open racks to house SMF batteries for 30 KVA

UPS system along with interconnecting links, MCCB etc.

complete as required & as per specifications.

Set 2.00

CustomerCustomerCustomerCustomerCustomerCustomer CustomerCustomerCustomerCustomerCustomerCustomerCustomerCustomer CustomerCustomerCustomerCustomerCustomerCustomerCustomerCustomer CustomerCustomerCustomerCustomerCustomerCustomerCustomerCustomerCustomerCustomerCustomerCustomer CustomerCustomerCustomerCustomerCustomerCustomerCustomerCustomer CustomerCustomerCustomerCustomer CustomerCustomerCustomerCustomer CustomerCustomerCustomerCustomerCustomerCustomerCustomerCustomerCustomerCustomer CustomerCustomerCustomerCustomerCustomerCustomerCustomerCustomerCustomerCustomer CustomerCustomerCustomerCustomerCustomerCustomerCustomerCustomer CustomerCustomerCustomerCustomerCustomerCustomerCustomerCustomer CustomerCustomerCustomerCustomerCustomerCustomerCustomerCustomerCustomerCustomerCustomerCustomer CustomerCustomerCustomerCustomerCustomerCustomerCustomerCustomer CustomerCustomerCustomerCustomer CustomerCustomerCustomerCustomer CustomerCustomerCustomerCustomerCustomerCustomerCustomerCustomerCustomerCustomer CustomerCustomerCustomerCustomerCustomerCustomerCustomerCustomerCustomerCustomer CustomerCustomerCustomerCustomerCustomerCustomerCustomerCustomer CustomerCustomerCustomerCustomerCustomerCustomerCustomerCustomer CustomerCustomerCustomerCustomerCustomerCustomerCustomerCustomerCustomerCustomerCustomerCustomer CustomerCustomerCustomerCustomerCustomerCustomerCustomerCustomer CustomerCustomerCustomerCustomer CustomerCustomerCustomerCustomer CustomerCustomerCustomerCustomerCustomerCustomerCustomerCustomerCustomerCustomer CustomerCustomerCustomerCustomer

Estimate 44 of 49


Rate (INR)

Bill of Quantities


Amount in figures

(INR)S.NO

DESCRIPTIONUNIT

Quantity

8) Supply, laying, testing & commissioning of flexible single core

copper cable of Finolex / Skyline/Grandlay/National make for

interconnections between UPS to UPS, UPS to batteries,

Isolation transformer to UPS complete as required for 30 KVA

UPS,including providing Battery circuit breakers as required.

Set 2.00

9) Supply,installation,testing and commissioning of UPS monitoring

software suitable for RJ-45 communication and capable of giving

pop up messages for all alarms received from UPS. It shall be

capable of the following:- a)Giving notifications like e-mail, paging

notification, broadcast notification, battery replacement

notification, run event-based scripts. b) Event logging, data

logging and action logging (with date, time, description of fault

and event. c) Run the battery diagnostic test. d) Automated

unattended shutdown of computers.. e) Local notification through

audible alarm, f) Software should support : Microsoft Windows

NT / 2000 / Server, 2003/XP, AIX, HP-UX, Sun Solaris, Linux,

Novell Netware. Note: (i) The quoted rates for above mentioned

items shall be inclusive of comprehensive warranty/maintenance

for 12 months defect liability period for UPS System incll.

Batteries, Battery Racks, Software, Cabling etc. (ii) The quoted

rates shall include full load testing at site for checking the UPS

rating and backup time of batteries.The Contractor shall arrange

the load testing at his own cost. (iii) Thequoted rates shall include

carrying out UPS performance test for checking of various

parameters with Fluke meter.

Set 3.00

Total Bill No. 10

Bill No. 11 : Modular Workstation and Loose Furniture

S. No. Item Description Unit

Estimate 45 of 49


Rate (INR)

Bill of Quantities


Amount in figures

(INR)S.NO

DESCRIPTIONUNIT

Quantity

1 STUDIO --Modular Workstation

45mm Thick, 1200 mm High Modular Partition made of aluminium

extruded sections duly powder coated with Fabric Pinboard on top

and Laminate below w/ provision of wiring raceways(Dual

Raceways) at the skirting. Partition should also be provided with

level adjusters.Workstation(1200x600x750mm) shall include a

individual Pedestal with 2D and 1F Configuration, Cable Manger

and Key tray. Workstation Cost also to include the 1250 mm

length Side Partition in same thickness with Glass and Frosted

film above and Laminate Sheet below as shown after interval of

every 2 workstations. Laminate Shade as approved for Worktop,

Sides and Drawer Unit : Merino Enthnik Oak 10895, Power

Coating Colour for Metal Trims : White, Fabric Shade for Pinup :

Sabhajeet Fabrics Pista Green SF 1417.

Nos. 100

2 STUDIO -- Modular Workstation

Cubical 45mm Thick, 1200 mm High Modular Partition made of

aluminium extruded sections duly powder coated with Fabric

Pinboard on top and Laminate below w/ provision of wiring

raceways(Dual Raceways) at the skirting. Partition is also

provided with level adjusters.Workstation shall include 1 nos.

Fixed Pedestal with 2D and 1F Configuration, Cable Manger and

Key tray. Workstation Top to be L shapes as per detail made of

1250 (Length) x 750 (Depth) mm on one side and 2150 (Lenght) x

475 (Depth) mm on other side.Cost also to include the 1250 mm

length Side Partition in same thickness with Glass and Frosted

film above and Laminate Sheet below as shown after interval of

ever 2 workstations. Refer Furniture for Sharing Configuration.

Laminate Shade as approved for Worktop, Sides and Drawer Unit

: Merino Enthnik Oak 10895, Power Coating Colour for Metal

Trims : White, Fabric Shade for Pinup : Sabhajeet Fabrics Pista

Green SF 1417.

Nos. 110

3 STUDIO---Modular Workstation (Linear) Guest

Workstation(1050x600x750mm)

with shared Pedastal Other specifications same as Item No. 1

above

Nos. 20

Estimate 46 of 49


Rate (INR)

Bill of Quantities


Amount in figures

(INR)S.NO

DESCRIPTIONUNIT

Quantity

4 STUDIO -- Modular Workstation (L Shape)

Guest Workstation(1500x1700x750)

With Fixed Pedastal

Other Specifications same as Item No. 2 above

Nos. 20

5 Cabin Desk made of 25 mm Thick Worktop of Size 1650 (Lenght)

mm x 600mm(width)x750 (Depth) mm and Side Unit of Size 900

(Lenght) mm x600mm(width)x 450 (Depth). Framing System to be

made of aluminium extruded sections duly powder coated as per

detail. Provision of Wire management System along with Cable

manager to be provided in front worktop. Cabin Desk Side unit to

consist of Shutters and Drawers as per detail. Laminate Shade as

approved for Worktop, Sides and Drawer Unit : Merino Planked

Maple 10870, Power Coating Colour for Metal Legs : White.

Nos. 60

6 Cabin Meeting Table : Meeting Table made of 25 mm Thick

Worktop of Size 900 mm Dia & 750mm height and Stainless Steel

Leg with Pedestal Base in Stainless Steel.Laminate Shade as

approved for Worktop : Merino Planked Maple 10870, Leg :

Stainless Steel.

Nos. 10

7 Cabin Back Storage : Storage of Size 900 mm (Lenght) x 450 mm

(Depth) x 750 mm (Height) made of 25 mm Thick Prelaminated

Board as per detail. Storage to be provided with 1 nos. adjustable

shelf complete with Handle, Lock and Hinges as per detail.

Laminate Shade as approved for Storage : Merino Planked Maple

10870.

Nos. 25

8 Meeting Room Tables : Oval Shape Meeting Table made of 25

mm Thick Worktop of Size 1650 mm (Length) x 900 mm (Width) x

750 mm (Height) with Pedestal Base in Stainless Steel with wire

manahement system. Laminate Shade as approved for Worktop :

Merino Planked Maple 10870, Leg : Stainless Steel.

Nos. 5

Estimate 47 of 49


Rate (INR)

Bill of Quantities


Amount in figures

(INR)S.NO

DESCRIPTIONUNIT

Quantity

9 Conference Table in Laminate : Oval Shape Meeting Table made

of 25 mm Thick Worktop of Size 3350 mm (Length) x 1200 mm

(Width) x 750 mm (Height) with Pedestal Base in Stainless Steel

with wire manahement system. Laminate Shade as approved for

Worktop : Merino Planked Maple 10870, Leg : Stainless Steel.

Cost to include 2 nos. electronic turnbox each having 2 data, 2

voice, 3 UPS power sockets and 1 projector socket.

Nos. 1

10 Workstation Area Medium Height Storage : Type 1 : Storage of

Size 1200 mm (Length) x 450 mm (Depth) x 1200 mm (Height)

made of 25 mm Thick Prelaminated Board as per detail. Storage

to be provided with 2 nos. adjustable shelf complete with Handle,

Lock and Hinges as per detail. Laminate Shade as approved for

Storage : Merino Ethnik Oak 10895.

Nos. 5

11 Workstation Area Medium Height Storage : Type 2 : Storage of

Size 900 mm (Length) x 400 mm (Depth) x 1200 mm (Height)

made of 25 mm Thick Prelaminated Board as per detail. Storage

to be provided with 2 nos. adjustable shelf complete with Handle,

Lock and Hinges as per detail. Laminate Shade as approved for

Storage : Merino Ethnik Oak 10895.

Nos. 5

12 Secratary Workstation

STUDIO ---Modular Workstation

46mm Thick, 1200 mm High Modular Partition made of aluminium

extruded sections duly powder coated with Fabric Pinboard on top

and Laminate below w/ provision of wiring raceways at the

skirting. Partition is also provided with level

adjusters.Workstation( 1350 X 600 X 750mm +

1400 X 1750 X 750mm + 600 X 600 X 750mm) shall include a

Shared Pedestal with 2D and 1F Configuration, Cable Manger

and Key tray.

Nos. 2

13 Providing and supplying office chairs, as per technical

specfications as approved by Enginner-in -charge

Executive type chairs Nos. 50

Officers chairs Nos. 150

Visitors chairs Nos. 50

Total Bill No. 11

Bill No. 12 : Development of working Detailed Drawings for civil and services

Estimate 48 of 49


Rate (INR)

Bill of Quantities


Amount in figures

(INR)S.NO

DESCRIPTIONUNIT

Quantity

1 Development of working Detailed Drawings for civil and services

(GFC)/ , detailed design / drawings for services work like

Electrical conduit/ cabling/ raceway, cable tray , DB’s, Lighting

layout, Power, HVAC ducting, CCTV, UPS, PA system, IT

networking/Data layout, Fire Alarm, Fire fighting piping etc and 3D

view of selected locations

Sqm 2000

Total Bill No. 12

Estimate 49 of 49

Documents

Development of DIMTS Office at 8th Floor, DMRC IT Park .... Bill of... · Cost to include 20 mm wide border frosting of mirror. SqM 24.00 9.00 MDF Panelling MDF PANELING : As per