37
Development of aluminium-silicon alloys with improved properties at elevated temperature PAPER WITHIN Materials and Manufacturing AUTHOR: Toni Bogdanoff TUTOR: Arne K. Dahle JÖNKÖPING May 2017

Development of aluminium-silicon alloys with improved ...1146050/FULLTEXT01.pdf · alloys have been investigated by several researchers during the last decade [1-3]. However, the

  • Upload
    others

  • View
    5

  • Download
    1

Embed Size (px)

Citation preview

Page 1: Development of aluminium-silicon alloys with improved ...1146050/FULLTEXT01.pdf · alloys have been investigated by several researchers during the last decade [1-3]. However, the

Development of

aluminium-silicon alloys

with improved properties

at elevated temperature

PAPER WITHIN Materials and Manufacturing

AUTHOR: Toni Bogdanoff

TUTOR: Arne K. Dahle

JÖNKÖPING May 2017

Page 2: Development of aluminium-silicon alloys with improved ...1146050/FULLTEXT01.pdf · alloys have been investigated by several researchers during the last decade [1-3]. However, the

This thesis has been carried out in the School of Engineering at Jönköping University

in the subject area Materials and Manufacturing. The work is a part of the one-year

Master of Science program in Foundry Technology.

The author takes full responsibility for all opinions, conclusions and findings

presented.

Examiner: Dr. Ehsan Ghassemali

Supervisor: Professor Arne K. Dahle

Scope: 15 credits

Date: 2017-10-02

Page 3: Development of aluminium-silicon alloys with improved ...1146050/FULLTEXT01.pdf · alloys have been investigated by several researchers during the last decade [1-3]. However, the

Abstract

Aluminium-silicon alloys have gained increasing market share in the automotive and

aerospace industry because of increased environmental demands. These alloys have a

high strength-to-weight ratio, good corrosion resistance, castability and recycling

potential. However, variations in properties and limited performance at elevated

temperature are restricting these alloys from use at elevated temperatures. During the

last decades, researchers have investigated ways to improve the properties at elevated

temperatures. However, the effect of some transition elements is not well understood.

The aim of this work is to investigate the aluminium-silicon alloys with addition of

cobalt and nickel for high temperature applications. Tensile testing and hardness testing

were conducted on samples produced by directional solidification in a Bridgman

furnace with condition generating a microstructure corresponding to that obtained in

high pressure die casting, i.e. SDAS ~ 10 µm. The results show that cobalt and nickel

improve the tensile properties up to 230 °C.

Keywords: Al-Si alloy – Nickel – Cobalt – Elevated temperature properties –

Microstructure

Page 4: Development of aluminium-silicon alloys with improved ...1146050/FULLTEXT01.pdf · alloys have been investigated by several researchers during the last decade [1-3]. However, the

Acknowledgements

As the author of this thesis I would like to take the opportunity to acknowledge the

people who supported me and made this thesis work possible.

Arne K. Dahle For being a supportive supervisor during this Masters

Professor thesis, guiding me through this work with excitement.

Materials and Manufacturing

Jonas Bäckman For his assistance and support during this work.

Research engineer

Swerea Swecast

Salem Seifeddine For being a source of inspiration and motivation source for

Professor me to continue to develop.

Materials and Manufacturing

Ehsan Ghassemali For assistance and support during this thesis.

PhD

Materials and Manufacturing

All my colleagues and friends at the Department of Materials and Manufacturing for

interesting discussions and support when needed.

And finally, to my family, for always being there to support me.

Page 5: Development of aluminium-silicon alloys with improved ...1146050/FULLTEXT01.pdf · alloys have been investigated by several researchers during the last decade [1-3]. However, the

5

Contents

Acknowledgements ........................................................................... 4

1 Introduction ....................................................................................... 6

1.1 BACKGROUND ...................................................................................................................................... 6 1.2 PURPOSE AND GOAL ............................................................................................................................. 6 1.3 DELIMITATIONS .................................................................................................................................... 7

2 Literature Survey .............................................................................. 8

2.1 BACKGROUND ...................................................................................................................................... 8 2.2 ALLOYING ELEMENTS........................................................................................................................... 9 2.3 SOLIDIFICATION ..................................................................................................................................11 2.4 STRENGTHENING MECHANISMS ...........................................................................................................12 2.5 EVALUATION OF THE TENSILE TESTING CURVE ....................................................................................13

3 Experimental ................................................................................... 14

3.1 CASTING ..............................................................................................................................................14 3.2 SAMPLE PREPARATION ........................................................................................................................15 3.3 MECHANICAL TESTING ........................................................................................................................16 3.5 CHARACTERIZATION TECHNIQUES.......................................................................................................18 3.5.5 THERMO-CALC .................................................................................................................................18

4 Results and discussion ...................................................................... 19

4.1 MICROSTRUCTURAL CHARACTERIZATION ...........................................................................................19 4.2 MECHANICAL PROPERTIES ..................................................................................................................23

5 Conclusions ...................................................................................... 32

6 Future work ..................................................................................... 33

7 References ....................................................................................... 34

Page 6: Development of aluminium-silicon alloys with improved ...1146050/FULLTEXT01.pdf · alloys have been investigated by several researchers during the last decade [1-3]. However, the

6

1 Introduction

The growing demands in the automotive and aerospace industry for reduction in energy

consumption and producing more fuel-efficient vehicles continues to be a big challenge.

The aluminium-silicon alloys have gained increased market shares in the aerospace and

automotive industry and have replaced competing ferrous materials. Aluminium-silicon

alloys are widely used in the automotive industry due to the high strength-to-weight ratio,

good corrosion resistance and good castability. However, the performance of aluminium-

silicon alloys at elevated temperature are limited because of degradations in the

mechanical properties. The effect of the elevated temperatures in aluminium-silicon

alloys have been investigated by several researchers during the last decade [1-3].

However, the effect of silicon, cobalt and nickel on the mechanical properties of

aluminium-silicon alloys at elevated temperatures has received limited attention.

The goal of this Masters thesis (15 Hp) is to investigate the effects of silicon, cobalt,

nickel on the mechanical properties of aluminium-silicon alloys at room and elevated

temperature.

1.1 Background

The topic for this thesis was developed based on discussions with Swerea Swecast. The

project was focused on improving alloy performance at elevated temperature. In the

aluminium-silicon foundry alloys, there are limitations in performance because of

degradations in the mechanical properties at elevated temperatures. The High Performing

Aluminium Cast Components (HPACC) project at Swerea Swecast was focused on

investigating the effect of zirconium and nickel in aluminium-silicon alloys at elevated

temperatures. The outcome from the discussions with Swerea Swecast was to study the

effect of silicon on the mechanical properties of aluminium-silicon alloys at elevated

temperatures. However, the effect of silicon has been investigated in various aluminium-

silicon alloys by several researchers [3-5]. Cobalt and nickel are transition elements that

have been used in high temperature applications in superalloys since 1930s [6]. Addition

of nickel in aluminium-silicon alloys are a common way to improve the mechanical

properties at elevated temperatures by forming aluminides [1, 7]. While the addition of

cobalt in aluminium-silicon alloys is rarely applied, some research has been conducted on

hypereutectic aluminium-silicon alloys that shows improved properties at 300 °C [8].

However, the combined additions of cobalt and nickel in other aluminium alloy systems

have demonstrated a great potential to increase the mechanical properties at elevated

temperature [9, 10]. Although the effect of combined addition of cobalt and nickel in

hypoeutectic aluminium-silicon alloys has rarely been reported in the literature.

1.2 Purpose and goal

The aim of this thesis is to gain a deeper understanding of aluminium-silicon alloys for

elevated temperature applications. The work focuses on the effect of silicon, cobalt,

nickel and strontium on the mechanical properties, thermal properties and microstructure

in aluminium-silicon alloys at room and elevated temperatures.

Page 7: Development of aluminium-silicon alloys with improved ...1146050/FULLTEXT01.pdf · alloys have been investigated by several researchers during the last decade [1-3]. However, the

7

1.3 Delimitations

This thesis is focussed on the effect of additions of Co, Ni and Sr as well on variations in

silicon content (7% and 15%) in aluminium-silicon alloys. The alloys were evaluated in

two conditions: as-cast and exposed at 240 °C for 1000 hours. The alloys investigated in

this study were produced by directional solidification with one solidification rate and

constant titanium and phosphorous contents. The mechanical properties were evaluated at

room temperature and at 230 °C, while the hardness measurements were evaluated at

room temperature. To understand the thermal behaviour of the alloys in this work,

measurements were conducted with differential scanning calorimetry (DSC) and

dilatometry up to 570 °C.

Page 8: Development of aluminium-silicon alloys with improved ...1146050/FULLTEXT01.pdf · alloys have been investigated by several researchers during the last decade [1-3]. However, the

8

2 Literature Survey

2.1 Background

The growing demands to produce more fuel efficiency vehicles have been triggered by

global warming concerns and legislations as well as reduced use of fossil fuels and

increased oil price. To reduce the energy consumption, the choice of materials become an

important factor which can lead to more light-weighting in the automotive and aerospace

industries [11]. Aluminium alloys are widely used in the transportation industry due to a

relatively low density resulting in more than 50 % weight savings compared with the

competing ferrous materials, without affecting the safety in most applications [12]. The

reduction of weight in automotive components is of importance since the weight of the

vehicles increases when more luxury, safety systems and comfort are required from the

customers. Aluminium alloys are divided into two major groups; wrought and cast alloys

and the usage is growing in the automotive industry. An average car today contains 175

kg aluminum, which is 120 kg more than in 1990s [13]. Most common aluminium

foundry alloys for castings have silicon as the major element with a content between 5-17

wt.%. Aluminium-silicon alloys is the most widely used alloys for castings due to their

high strength-to-weight ratio, excellent castability, corrosion resistance and high thermal

conductivity [14, 15]. Moreover, another advantage is the possibility to recycle more than

90 % of the aluminium after the end of use. Recycling aluminium only uses 5 % of the

energy needed to produce the same amount of virgin aluminium. Aluminium can be

recycled several times. However, the mechanical properties of secondary aluminium are

generally lower than in primary alloys [15]. In aluminium-silicon alloys, other alloying

elements need to be added beside the silicon such as: Mg, Cu, Fe, Ni, Sr. to modify the

properties. The mechanical properties in aluminium-silicon alloys depends on the

microstructure, chemical composition, defects. [16-18]. The microstructure of

aluminium-silicon alloy is characterized by α-dendrites, primary silicon particles,

aluminium-silicon eutectic, intermetallics and other precipitate phases depending on the

chemical composition [19, 20]. Aluminium-silicon alloys have a wide range of

applications for example, in engine applications were the material is exposed to elevated

temperatures. However, using these alloys at temperatures above 200 °C will start

coarsening of silicon phases, that have a negative impact on the mechanical properties [3,

19]. Several studies during the last decades with addition of transition elements are

forming thermally stable phases that improves the mechanical properties at elevated

temperature in aluminium-silicon alloys [21-24].

Page 9: Development of aluminium-silicon alloys with improved ...1146050/FULLTEXT01.pdf · alloys have been investigated by several researchers during the last decade [1-3]. However, the

9

2.2 Alloying elements

The most common aluminium foundry alloys are based on the aluminium-silicon system

because of their outstanding properties such as: superior castability, corrosion resistance,

good wear properties, good fluidity, low melting point and good machinability.

Increasing the silicon level will reduce the thermal expansion, increase the wear

properties and reduce the machinability [2, 25]. The silicon content and morphology

influence the mechanical properties both in room temperature and elevated temperature

[3]. The morphology of the silicon phase can be refined with chemical modification that

changes the silicon from plate-like to a fibrous structure. This modification is explained

by two well established growth models, impurity induces twinning and twin plane re-

entrant edge growth [26-28]. Moreover, the silicon can be refined by thermal

modification (quench modification) [29]. The hard silicon phases in a soft aluminum

matrix could be compared with a metal matrix composite. This network of silicon

contributes to an increasing strength of the material by enhanced load transfer [1, 30].

When the aluminium-silicon alloys are exposed to elevated temperature over long times,

coarsening occurs to the eutectic silicon phases, this reduces the mechanical properties

[21]. Copper and magnesium are two often important alloying elements for aluminium-

silicon alloys that are commonly used in the industry. Both these elements increase the

strength of the alloys at room temperature and elevated temperatures by solid solution

strengthening and dispersion strengthening mechanisms [31-33]. Copper maximum solid

solubility in aluminium is 5.65 wt.% at 548 °C and Magnesium is 14.9 wt.% at 451 °C.

[34] The addition of transition elements has been studied over several decades with the

goal to improve the mechanical properties at elevated temperature. In the last decades

researchers have focused on microalloying with rare elements such as: Sc, Yb. [35, 36]

However, the commercial use of rare earth elements is restricted by the high cost. The

transition elements nickel and cobalt are cheap comparing to the rare element, which has

led to more attention when developing new alloys for use at elevated temperature [37]. Knipling et al. [7] reported that the Ostwald ripening process must be slowed down on

the dispersed phases formed, in order to develop a castable thermally stable aluminium

alloy. The rate of coarsening can be reduced when the solutes displays the following

characteristics [7, 22];

• ability to form high volume fraction of strengthening intermetallic phases, • low diffusivity in α-Al, • low solid solubility in α-Al, • ability to form precipitates that possess similar crystal structure and low lattice

parameter mismatch with α-Al.

The transition elements can form trialuminides with the above characteristics that will

contribute to the improvement of high temperature properties. The transition elements

forming thermodynamically stable trialuminides intermetallic are e.g. Sc, Y, Ti, Zr [22].

Nickel is commonly added to aluminium-silicon alloys to enhance the strength and

hardness at elevated temperatures by the formation of thermally resistant Ni-rich

compounds such as: Al3Ni, Al9FeNi, Al3CuNi, etc. [10, 22, 28]. The solid solubility of

nickel in aluminum is below 0.04 wt.% and it therefore forms intermetallic compounds in

the interdendritic regions during solidification that contributes to an improved strength at

elevated temperatures. Addition of nickel to the aluminium-silicon system is

characterized by a microstructure of joined Al3Ni and eutectic silicon that strengthening

the 3D-network. The silicon phases are subjected to a coarsening and spheroidize during

Page 10: Development of aluminium-silicon alloys with improved ...1146050/FULLTEXT01.pdf · alloys have been investigated by several researchers during the last decade [1-3]. However, the

10

solution treatment which results in a loss in the interconnectivity of the eutectic silicon

phases in the 3D-network. However, with Ni-rich compounds present, the loss of

interconnectivity is reduced [1, 38]. Work by Kaya et al. [39] showed that a Al-12.6Si

alloy with addition of 2 wt.% nickel modifies the characteristics of the microstructure. A

finer silicon structure with a reduced interflake spacing is achieved, which results in an

improvement of the hardness [39].

The transition element cobalt is rarely used in hypoeutectic aluminium-silicon alloys,

most researchs with cobalt has been performed in hypereutectic alloys. Addition of cobalt

reduces the interflake spacing with a higher efficiency than nickel and with significant

improvements of the hardness [8, 39]. The combined effect of additions of cobalt and

nickel were investigated by Choi et al.[10] on an Al-1.1%Si-1.0%Mg alloy. Comparing

the results with a A319 alloy clearly showed that the alloy with combined addition of

cobalt and nickel is having a great potential for elevated temperature applications - see

Figure 1. The mechanical properties shows a minimal reduction of strength even at

temperatures above 250 °C [10].

Figure 1. Tensile properties at different temperatures in a

Al-1.1%Si-1.0%Mg and a A319 alloy [10].

Naeem et al. [37] reported an improvement in yield strength and ultimate tensile strength

with the combined addition of nickel and cobalt in an Al-Zn-Mg-Cu alloy. Naeem

reported that the addition of cobalt and nickel were acting as nucleation center in the

melt, resulting in a reduced grain size. The increase in strength were generated from

more than one strengthening mechanism - these mechanisms were Orowan strengthening,

Hall-Petch strengthening and precipitation hardening. Addition of cobalt in a

hypereutectic aluminium-silicon alloy were conducted by Sha et al. [8], which concluded

that addition of approximately 0.7 wt.% improved the tensile properties both at room and

elevated temperature (300 °C).

Page 11: Development of aluminium-silicon alloys with improved ...1146050/FULLTEXT01.pdf · alloys have been investigated by several researchers during the last decade [1-3]. However, the

11

Most aluminium alloys are initially grain refined by addition of titanium in the form of

master alloys. The titanium exists as Al3Ti and TiB2 particles in the melt. However, the

Al3Ti dissolves in the melt over time and the TiB2 tends to settle and agglomerate. The

effect of grain refining is over time [40, 41].The TiB2 particles are stable phases in the

melt and act as heterogeneous nuclei during solidification [42]. When the level of

titanium is higher than the solubility limit in the α-aluminium, properitectic Al3Ti forms

in the melt. The formation of Al3Ti on the TiB2 particles promotes the nucleation

efficiency [43]. Grain refining in aluminium-silicon alloys by inoculation through a

master alloy such as: Al-5Ti-1B, Al-4B etc. improves feeding, castability and reduce and

distributes shrinkage porosity [44].

In hypereutectic aluminium-silicon alloys, phosphorous is always added to refine the

primary silicon particles. The amount of phosphorous addition required to achieve an

effective refinement varies from 0.005 % to 0.03 %. The result of phosphorous addition

reduces the size of primary silicon in the order 5-10 times. However, the number of

primary silicon particles increases [19]. Samuel et al. [45]reported that the primary

silicon particles nucleate on phosphorous-based compounds (AlP) or oxide films.

The morphology and size of the silicon crystals strongly affects the mechanical

properties of the aluminium-silicon alloys. Strontium is a eutectic modifier which

transforms the silicon morphology from flake-like to a fibrous shape[44]. Moreover,

there are several other modifiers such as: Na, Ca, Sb, etc. [26, 27, 46, 47]. The effects of

the modification in the molten aluminium-silicon alloys diminish over time by

vaporization and surface oxidation. The combined additions of boron and strontium may

form the SrB6 compounds which reduces the active amount of strontium available for

modification [35, 39]. The first modification techniques used sodium as a modification

element. However, there is challenges in using sodium because of the high vapor

pressure and rapid fading. This has made strontium the most common modifier in

aluminium alloys. Even with the challenges to add the sodium, some sand casting

foundries are using at a large scale [48]. The benefit of modification with strontium and

sodium have shown an increased ductility in the aluminium-silicon cast alloys because of

the shape difference in the morphology [44, 49].

2.3 Solidification

Depending on the amount of silicon in the aluminium-silicon alloys, the solidification

sequence will change: In the hypoeutectic alloys with a silicon level below 12.6 wt.%

cluster of atoms will form and dissolve in the melt when the temperatures is above the

liquidus temperature. This will continue until the melt reaches the nucleation temperature

of the α-dendrites. The nucleation of aluminium starts on heterogeneous nucleation sites

in the melt and is then followed by either columnar or equiaxed growth [50]. The

temperature will continue to decrease until the start of the aluminium-silicon eutectic

reaction where the aluminium and silicon needs to nucleate and then grow

simultaneously [51]. Even in a process such as high pressure die casting will there be

variation in the microstructure which is related to the local solidification time. These

variations are measured as the distance between the secondary dendrite arms (SDAS).

Generally, with increasing solidification rate, the SDAS, eutectic structure and

intermetallics are modified. In the binary aluminium-silicon phase diagram at ~12.6 wt.%

silicon is the eutectic point. At silicon levels above 12.6 wt.%, the solidification begins

Page 12: Development of aluminium-silicon alloys with improved ...1146050/FULLTEXT01.pdf · alloys have been investigated by several researchers during the last decade [1-3]. However, the

12

with the formations of primary silicon crystals. The silicon crystals morphology, size and

distribution can change remarkedly during the solidification depending on cooling rates,

number of impurities and the ease of nucleation [8].

2.4 Strengthening mechanisms

The strength of the aluminium-silicon alloys is derived from the ability of precipitates and atoms to hinder the movement of dislocations. When deformation occurs without any obstacles present, a dislocation can move easily with only a small force needed. The most important mechanism during plastic deformation is dislocation slip. The edge dislocation (Taylor-Orowan) and screw dislocation is the two most common types. These precipitates are either sheared by the moving dislocations or creating a loop around the precipitates that increases the size of the precipitate. The grain boundaries act as an obstacle for moving dislocation during plastic deformation, an increased misorientation angle between the neighboring grains will make the movement of dislocations over the grain boundaries more difficult.

The strength of an aluminium-silicon alloy is commonly decreased when the temperature is increased because of the resistance to moving dislocation is reduced. When the temperature increases, the dislocation climb and dislocation slip assisted by thermal vibrations and diffusion of vacancies will increase. Dislocation climb is a process of an edge dislocation which move out of the slip plane onto a parallel plane directly above or below [31].

Page 13: Development of aluminium-silicon alloys with improved ...1146050/FULLTEXT01.pdf · alloys have been investigated by several researchers during the last decade [1-3]. However, the

13

2.5 Evaluation of the tensile testing curve

The mechanical characteristics of a materials properties in a uniaxial tensile test are displayed in a stress-strain curve. These results show the engineering stress and engineering strain, that are calculated with a constant cross-section area during the whole deformation. When the reduction of this cross-section area is taken into consideration, the true stress and true strain can be calculated.

The results from the tensile testing curves is characterized using Hooke´s law (1) for the elastic region.

𝜎 = 𝐸 ∗ 𝜀𝑒𝑙 (1)

Here is 𝜎 = Stress (Pa), E = Young´s modulus and 𝜀𝑒𝑙 = the elastic strain. To evaluate the plastic region, the Hollomon (2) equation is used [31, 52].

𝜎 = 𝐾 ∗ 𝜖𝑝𝑙𝑛 (2)

Here is 𝜎 = true stress (Pa), K = strength coefficient, n = strain hardening exponent and 𝜀𝑝𝑙 = true plastic strain - see Figure 2.

Most materials used in engineering applications have a linear elastic region. However, it could be hard to determine the transition between the elastic part and the non-linear plastic part [52].

Figure 2. Illustration of how the different parameters

are related to the tensile testing curve [31].

Page 14: Development of aluminium-silicon alloys with improved ...1146050/FULLTEXT01.pdf · alloys have been investigated by several researchers during the last decade [1-3]. However, the

14

3 Experimental

3.1 Casting

Four hypoeutectic alloys and two hypereutectic alloys were prepared from pure aluminium,

pure silicon, and various master alloys to produce the alloys in this investigation. Around

250 ppm of titanium was added by a Al-5Ti-1B master alloy in rod shape. This amount of

titanium will produce alloys with refined grain sizes [40]. Phosphorous in the range of 50-

70 ppm were added to the alloys with an Al-3P master alloy. The alloys were melted in a

7 Kg Nabertherm K4/13 resistance furnace. When the melt reached a temperature of

730 °C it was homogenized for 1 hour before the addition of master alloys, modifier and

grain refiner were performed. All additions were wrapped in aluminum foil and preheated

to 200 °C before addition to the melt at 730 °C. The chemical composition of each alloy

were obtained using a SPECTROMAXx LMX06 optical emission spectrometer - see Table

1. The melt was poured into a pre-heated (200 °C) copper die to obtain cylindrical rods

(length 20 cm, diameter 1 cm) - see Figure 3 a and 3 b. The die cast cylindrical rods were

then re-melted in steel tubes coated with graphite under argon-atmosphere by directional

solidification in a Bridgman furnace - see Figure 4. The temperature was set to 730 °C and

the samples were held in the furnace for 30 minutes. Once the samples were re-melted, the

furnace was raised at the prescribed speed of 3 mm/s, while the samples stayed in a

stationary position. The solidification set-up generates samples with low levels of defects

due to directional solidification that push, to some extent, gas and oxides in front of the

solidification front and good provider of feed liquid from the top.

(a) (b)

Figure 3. (a) Permanent copper die, (b) Sample from the casting in the copper die.

Figure 4. The Bridgman furnace set-up.

Page 15: Development of aluminium-silicon alloys with improved ...1146050/FULLTEXT01.pdf · alloys have been investigated by several researchers during the last decade [1-3]. However, the

15

Table 1. The chemical composition of all alloys (wt.%)

Nr Alloys Si Co Ni Sr (ppm) Fe Al

1 Al-7Si

6.81 ± 0.06 - - -

0.079 ± 0.01 Bal.

2 Al-7Si-Co

6.63 ± 0.05

0.48 ± 0.007 - -

0.082 ± 0.02 Bal.

3 Al-7Si-Co-Ni

6.05 ± 0.04

0.82 ± 0.01

0.80 ± 0.01 -

0.083 ± 0.004 Bal.

4 Al-7Si-Co-Ni-Sr

6.61 ± 0.03

0.47 ± 0.004

0.55 ± 0.008 290 ± 10

0.089 ± 0.01 Bal.

5 Al-15Si

15.06 ± 0.11 - - -

0.11 ± 0.002 Bal.

6 Al-15Si-Co-Ni

13.22 ± 0.10

0.84 ± 0.004

0.71 ± 0.01 -

0.11 ± 0.001 Bal.

3.2 Sample preparation

The directional solidified bars were machined into cylindrical tensile testing bars according

to the geometry shown - see Figure 5. The samples for tensile testing at elevated

temperatures were machined with a M9*1 tread.

Figure 5. Tensile bar geometry. Dimensions are in mm.

Ten tensile samples were used in the as-cast condition while ten bars were exposed at 240

C for 1000 hours. Most research is carried out on materials in the as-cast or heat treated

conditions. The material has been overaged to replicate the materials properties after long

time exposure at elevated temperatures.

To evaluate the hardness variations over time the samples have been exposed at 240 C for

different times; 0, 12, 330, 671 and 1000 hours.

The as-cast and overaged samples were mounted with polyfast material in a Struers

Citopress-1 followed by grinding and polishing with a Struers Tegramin-30. Additional

polishing with OP-S were required for the grain size measurements.

After the final polishing, the samples were investigated with optical microscopy, scanning

electron microscopy, Micro Vickers and nanoindentation.

Page 16: Development of aluminium-silicon alloys with improved ...1146050/FULLTEXT01.pdf · alloys have been investigated by several researchers during the last decade [1-3]. However, the

16

3.3 Mechanical testing

3.4.1 Tensile testing

The tensile testing was carried out using a Zwick/Roell Z100 testing machine at room

temperature and at 230 °C with a deviation of ± 2 °C and a test speed of 0.5 mm/min.

The strain was measured by a clip-on extensometer at room temperature, while at the

elevated temperatures it was measured by a laser extensometer. The laserXtens is a non-

contact laser extensometer that satisfies the accuracy requirement of class 1 while the

clip-on extensometer is more accurate and used in room temperature having the

requirements of class 0.2. The tensile testing at elevated temperatures involved heating of

the samples to equilibration for 30 minutes in a resistance furnace. At least three samples

were tested of each condition. The results exported from the tensile testing equipment is

the engineering stress and engineering strain which are re-evaluated to true stress and

true strain.

3.4.2 Nano indentation

The indentation analysis in this work was performed using a Micromaterials Nanotest

Vantage instrument. The equipment can apply loads in the range of 0.5 mN to 20 N and

record load and displacement simultaneously during indentations. The results are presented

as a load-displacement curve with peak indentation depth - see Figure 6. Oliver and Pharr

developed a method with a standard procedure to calculate the hardness and reduced elastic

modulus [53]. A Berkovich diamond indenter was used in the experiment setup. First a

grid of 36 indents (6X6) using a load of 200 mN with a spacing of 100 μm was tested. The

second grid was 144 indents (12X12) using a load of 5 mN with a spacing of 7 μm.

Figure 6. Load-displacement curve from the Micro material Nanotest Vantage system.

Page 17: Development of aluminium-silicon alloys with improved ...1146050/FULLTEXT01.pdf · alloys have been investigated by several researchers during the last decade [1-3]. However, the

17

3.4.3 Macro Vickers

The hardness of the alloys was measured using an Alpha Durometer hardness tester

following the standard ISO 6508, with a load of 20 kg and a loading time of 15 seconds.

Five indentation were performed on the surface of each sample. The hardness testing was

carried out on the as-cast samples and samples exposed at 240 C for times up to 1000

hours. The measurements of the indents were conducted with an Olympus GX 71

microscope.

3.4.4 Micro Vickers

Indentations were performed on the polished surface with a load of 500 mg using a Micro

Vickers equipment following the standard ISO 6508. The result was measured with an

Olympus GX 71 microscope.

Page 18: Development of aluminium-silicon alloys with improved ...1146050/FULLTEXT01.pdf · alloys have been investigated by several researchers during the last decade [1-3]. However, the

18

3.5 Characterization techniques

3.5.1 Optical microscope

Representative areas within the gauge length of the cast samples were investigated using an Olympus GX 71 microscope. Magnifications up to 100 X was used to investigate the microstructures and fracture surfaces. Average SDAS from 10 measurements from the directional solidification direction and 10 from the perpendicular direction have been carried out in all alloys. The Olympus stream motion image analyzer was used to quantify the microstructures.

3.5.2 Scanning electron microscope A JEOL7001F scanning electron microscope equipped with an energy dispersive

spectrometer (EDS) was used for analysis of the alloys. Mapping of representative areas

of the microstructure were carried out to show the distribution of different phases. The

grain size was determined from the gauge length of the alloys using electron backscatter

diffraction (EBSD) on an area of minimum 1.5 mm2. The grain size was measured by the

intercept method according to ASTM E112-96. The grains were visualized using inverse

pole figure (IPF) maps in the EBSD analysis. The EBSD measurements were done using

an acceleration voltage of 15 KV and a step size of 3 µm.

3.5.3 Differential scanning calorimeter

The differential scanning calorimetry equipment was used to investigate phase transformations which occurs during heating or at long term exposure at elevated temperature. The Netzsch DSC 404C Pegasus instrument performed the testing in this investigation. Cylindrical samples with a diameter of 5 mm and a weight of ~42 mg was produced. The samples were heated from room temperature up to 600 °C under an argon atmosphere with a heating rate of 5 K/min.

3.5.4 Dilatometer

An Netzsch DIL402 were used to measure the thermal expansion of the alloys. The reference material Al2O3 was used as a standard reference. Cylindrical rods were produced with a diameter of 6 mm with a length of 12 mm using a lathe. The testing was carried out under a helium atmosphere with a heating rate of 5 K/min from room temperature up to 570 °C.

3.5.5 Thermo-Calc

The Thermo-Calc software version 2016b with the data base TCAL was used to predict

which phases are expected to be present in the alloys; equilibrium calculations were

carried out on all alloys.

Page 19: Development of aluminium-silicon alloys with improved ...1146050/FULLTEXT01.pdf · alloys have been investigated by several researchers during the last decade [1-3]. However, the

19

4 Results and discussion

4.1 Microstructural characterization

The as-cast hypoeutectic Al-7Si alloy is comprised of α-dendrites and aluminium-silicon eutectic - see Figure 7 a. Adding 0.4 wt.% cobalt did not produce any significant changes in the microstructure - see Figure 7 b. Moreover, cobalt rich phases are observed in the microstructure. However, no significant differences in the SDAS is observed in the microstructures compared with the Al-7Si alloy - see Table 2. The reduction of the interflake spacing λ between the silicon eutectic phases with addition of cobalt reported by Kaya et al. [39] is not observed in this work. This may depend on a lower addition of cobalt or a higher solidification rate. The cobalt-rich phase Al9Co2 is located in the vicinity of the α-dendrites and refine and distributed the silicon phases in the aluminium-silicon eutectic - see Figure 7 b. According to Thermo-Calc, the Al9Co2 nucleates before the α-dendrites - see Figure 8.

Figure 7. (a) Microstructure of the Al-7Si alloy, (b) Microstructure of the Al-7Si-Co alloy.

Table 2. Results from the SDAS measurements of as-cast hypoeutectic alloys.

(a) (b)

Alloy Al-7Si Al-7Si-Co Al-7Si-Co-Ni Al-7Si-Co-Ni-Sr

SDAS (μm) 11.3 ± 1.8 10.4 ± 0.5 8.5 ± 0.7 9.5 ± 0.9

Page 20: Development of aluminium-silicon alloys with improved ...1146050/FULLTEXT01.pdf · alloys have been investigated by several researchers during the last decade [1-3]. However, the

20

Figure 8. Results from equilibrium calculation on Al-7Si-Co using Thermo-Calc.

The microstructure of the Al-7Si-Co-Ni alloy have an aluminum-silicon eutectic morphology with a higher degree of modification adjacent to the nickel and cobalt phases. However, these intermetallic phases could increase the contiguity of the 3D-network but it is difficult to observe based on the micrographs - see Figure 9 a. The effect of the combined additions of cobalt and nickel in aluminium alloys with 1.1 % silicon is reported by Choi et al.[10] to have a good potential for high temperature properties. The addition of nickel have been reported to form a strong interconnected three-dimensional structure with Al3Ni and eutectic silicon [3]. The additions of chemical modifier in the form of strontium in the Al-7Si-Co-Ni-Sr showed a well-modified microstructure - see Figure 9 b. Moreover, the intermetallics are decreased significantly in size in the strontium modified alloy. However, all other alloys were showing a silicon morphology that is cooling rate refined as reported [21, 46].

Figure 9. (a) Microstructure of the Al-7Si-Co-Ni alloy, (b) Microstructure of the Al-7Si- Co-Ni-

Sr alloy.

(a) (b)

Page 21: Development of aluminium-silicon alloys with improved ...1146050/FULLTEXT01.pdf · alloys have been investigated by several researchers during the last decade [1-3]. However, the

21

Additions of Al-5Ti-1B were conducted to produce a grain refining effect in all alloys. The performance of the grain refiners are negatively affected with increasing the silicon content in aluminium-silicon alloys because of the silicon poisoning effect [54, 55]. Addition of grain refiners with approximately 250 ppm titanium was performed in all hypoeutectic alloys in this work. However, the results from the EBSD clearly shows that the addition of cobalt and nickel have a significant effect on the grain size. The Al-7Si alloy have a grain size of around 131 μm while the other alloys show results with increased grain size - see Figure 10 and Table 3. The TiB2 particles in the melt may act as nucleation sites for intermetallics formed prior the α-dendrites, resulting in a reduced grain refining efficiency because of fewer TiB2 particles are available for nucleation of α-dendrites.

Al-7Si Al-7Si-Co

Al-7Si-Co-Ni Al-7Si-Co-Ni-Sr

Figure 10. Inverse Pole Figure (IPF) map obtained from the EBSD mapping, showing grain

structure of the hypoeutectic alloys.

Table 3. Results from the grain size measurements of the as-cast hypoeutectic alloys.

Alloys Al-7Si Al-7Si-Co Al-7Si-Co-Ni Al-7Si-Co-Ni-Sr

Grain size (μm) 131 ± 21 174 ± 14 260 ± 44 286 ± 27

Page 22: Development of aluminium-silicon alloys with improved ...1146050/FULLTEXT01.pdf · alloys have been investigated by several researchers during the last decade [1-3]. However, the

22

The Al-15Si alloy is composed of hard and stiff primary silicon particles, aluminium-silicon eutectic and α-dendrites - see Figure 11 a. These hypereutectic alloys could vary in properties and microstructure depending on the chemical compositions, manufacturing process and the solidification rate. However, in these samples the solidification begins with the formation of primary silicon followed by a competition of aluminium-silicon eutectic and aluminium dendrites [50, 56, 57]. The primary silicon crystals were found in both Al-15Si and the alloy with addition of cobalt and nickel. The hypereutectic alloys with primary silicon crystals must be modified using phosphorous, the silicon crystals will otherwise be detrimental to the mechanical properties. The modification of the primary silicon crystals with phosphorous reduces the size in the order 5-10 times [19]. The size of the primary silicon crystals in the Al-15Si alloy are 35.9 μm ± 5.4 which indicates that there is a refinement effect. The combined addition of cobalt and nickel to the Al-15Si alloy were reducing the silicon content. The Al-15Si-Co-Ni alloy have less and smaller primary silicon crystals - see Figure 11 b. Moreover, the intermetallic phases are well distributed in the Al-15Si-Co-Ni alloy found both in the vicinity of the aluminium dendrites and in the aluminium-silicon eutectic - see Figure 12. The size of the primary silicon crystals was decreased by ~20 % in the Al-15Si-Co-Ni, this may be caused by the reduced silicon content in the alloy - see Table 1.

Figure 11. (a) Microstructure of the Al-15Si alloy, (b) Microstructure of the Al-15Si-Co-Ni

alloy.

(a) (b)

Page 23: Development of aluminium-silicon alloys with improved ...1146050/FULLTEXT01.pdf · alloys have been investigated by several researchers during the last decade [1-3]. However, the

23

Figure 12. Microstructure of the Al-15Si-Co-Ni alloy showing the distribution of the intermetallic

phases.

4.2 Mechanical properties

A clear trend is observed in the tensile test results at room and elevated temperatures. By increasing the temperature up to 230 °C, both the yield strength and ultimate tensile were negatively influenced in all alloys. However, the elongation to failure for all the as-cast alloys were improved with increased temperature to 230 °C. This is in agreement by work of Rincon et. Al [58].

4.2.1 Tensile testing at room temperature.

There are several parameters that influences the mechanical properties in the aluminium-silicon alloys such as, chemical composition, solidification rate and intermetallics and defects etc. The effect of increasing the silicon content from 7 wt.% to 15 wt.% (Al-7Si and Al-15Si) significantly improves the yield strength by 76 % and ultimate tensile strength by 21 % - see Figure 13 a and Table 4. The results for the ultimate tensile strength correspond well with previous works [1, 20]. However, the increase of the silicon content is detrimental for the elongation to failure - see Figure 14 b. The fracture behaviour is governed by plastic deformation of α-dendrites and elastically strained particles. Once the alloys are exposed to plastic deformation the brittle particle start to form micro-cracks concentrated at the primary silicon phases and in the aluminium-silicon eutectic regions. These cracks propagate until a critical volume is reached that leads to crack coalescence and final fracture.

Nickel and

cobalt rich

phases.

Page 24: Development of aluminium-silicon alloys with improved ...1146050/FULLTEXT01.pdf · alloys have been investigated by several researchers during the last decade [1-3]. However, the

24

Figure 13. Results from the tensile testing at room temperature (a) Ultimate tensile strength,

(b) Elongation to failure.

Only a limited improvement of the ultimate tensile strength was observed with addition

of cobalt to the Al-7Si alloy - see Figure 13 a. However, the result for the combined

addition of cobalt and nickel on the ultimate tensile strength show an improvement by ~8

%. This improvement could be because of a higher degree of contiguity of the eutectic

silicon and intermetallic network or as a result of dispersion strengthening. The effect of

strontium in the Al-7Si-Co-Ni-Sr alloy was clearly observed in the microstructure

although the result from the tensile testing is similar. The elongation to failure results

were above 10 % in all hypoeutectic alloys with addition of transition elements, while the

elongation to failure of the Al-7Si alloy is more than 17 %. The Al-15Si-Co-Ni alloy

show results in the ultimate tensile strength that is having an improvement by ~17 %

without significant change in elongation to failure compared to the Al-15Si alloy.

Table 4. Summary of tensile testing results at room temperature for all alloys.

(a) (b)

Alloys Al-7Si Al-7Si-Co Al-7Si-Co-Ni Al-7Si-Co-Ni-Sr Al-15Si Al-15Si-Co-Ni

UTS (MPa) 197.6 ± 3.4 201.7 ± 1.7 213.4 ± 2.5 216.4 ± 1.4 239.2 ± 3.5 261 ± 7.3

YS (MPa) 64.1 ± 3.1 70.2 ± 2.2 71.6 ± 1.2 72.9 ± 0.8 112.9 ± 3.6 113.8 ± 0.8

Elongation to failure

(%) 17.4 ± 3 15.9 ± 0.6 11.5 ± 2.3 12.9 ± 1.2 4.9 ± 0.5 3.9 ± 0.8

Page 25: Development of aluminium-silicon alloys with improved ...1146050/FULLTEXT01.pdf · alloys have been investigated by several researchers during the last decade [1-3]. However, the

25

4.2.2 Long-term exposure at elevated temperatures.

In order to understand the behaviour of the alloys after long-term exposure at elevated temperature, the alloys were exposed at 240 °C for 1000 hours. When the alloys are exposed to elevated temperatures, they strive to reach the equilibrium state - coarsening or dissolution of phases may occur. The results from the tensile testing at room temperature and at 230 °C is shown - see Figure 13 a and 13 b. The effect of the long-term exposure of the aluminium-silicon alloys show a reduction in the ultimate tensile strength and improvement in the elongation to failure for all alloys. Moreover, the level of reduction in ultimate tensile strength is similar for all alloys. The improvement of the ultimate tensile strength in the Al-7Si-Co-Ni alloy remains after long term exposure at elevated temperatures. These results are in accordance with the literature using nickel [3]. However, these improved results could be because of the stability in the aluminium-silicon eutectic and intermetallics 3D network. The hypereutectic alloys are following the same trend and the ultimate tensile strength is reduced by approximately 50 MPa.

4.2.3 Tensile testing at elevated temperatures.

The results from the tensile testing at 230 °C are shown - see in Figure 14 a and 14 b. The Al-7Si-Co alloy showed the same trend as in room temperature, while the combined addition of cobalt and nickel increased the ultimate tensile strength by ~32 % compared to the Al-7Si alloy - see Figure 14 a. The effect of adding transition elements to a hypoeutectic aluminium-silicon alloys was clearly reducing the elongation to failure. However, this effect was not found in the hypereutectic alloys that even with addition of transition element have similar elongation to failure results. This could be because of the silicon phases, which is detrimental to the hypereutectic alloys are the major factor for the elongation to failure - see Figure 14 b.

4.2.4 Long-time exposure at elevated temperatures.

From the tensile testing at elevated temperature of the alloys exposed at 240 °C for 1000 hours, it could be concluded that the Al-7Si-Co-Ni alloy show an ~23 % improvement in the ultimate tensile strength compared with the Al-7Si alloy. This improvement may depend on the contiguity of the silicon and intermetallic network is more rigid in Al-7Si-Co-Ni alloy. The Al-15Si-Co-Ni alloy shows an improvement of ultimate tensile strength at elevated temperature by 13 %, compared with the Al-15Si alloy - see Figure 14 a. Moreover, the elongation to failure is increased with addition of cobalt and nickel in the hypereutectic alloys from 7.7 % to 11 % - see Figure 14 b.

Page 26: Development of aluminium-silicon alloys with improved ...1146050/FULLTEXT01.pdf · alloys have been investigated by several researchers during the last decade [1-3]. However, the

26

(a) (b)

Figure 14. Results from the tensile testing at 230 °C (a) Ultimate tensile strength,

(b) Elongation to failure.

4.2.5 Hardness

The nanoindentation method was developed to measure the hardness of materials using a

Berkovich indentor. The data from the indentation are obtained from a load-displacement

curve, recording both the loading and unloading cycle. The alloys in this work was

evaluated with two different set-ups:

1. 12 X 12 indents with a load of 5 mN, distance between the indents were 7 μm. 2. 6 X 6 indents with a load of 200 mN, distance between the indents were 100 μm.

The results from the first set-up can separate the hardness values between various areas

in the microstructure such as: α-dendrites, aluminium-silicon eutectic and intermetallics.

From the first set-up experiment on the Al-7Si alloy is the results shown - see Figure 15.

The software is using the Oliver and Pharr method to perform the analysis of the

indentations.

(a) (b)

Figure 15. (a) Microstructure after indentation on Al-7Si alloy, (b) Hardness map from the

analysis.

Page 27: Development of aluminium-silicon alloys with improved ...1146050/FULLTEXT01.pdf · alloys have been investigated by several researchers during the last decade [1-3]. However, the

27

After that all indentation was performed and analysed, the software gives the results as a

hardness map - see Figure 15 b. The individual result from the indentations were then

sorted and categorized into α-dendrites or aluminium-silicon eutectic, those indentations

hitting hard intermetallics was excluded - see results in Table 5. At least 15 indentations

in each category were analyzed for the results. It is a clear difference between the α-

dendrites and the aluminium-silicon eutectic. However, no significant variation of

hardness was found in the α-dendrites or the aluminium-silicon eutectic with addition of

cobalt and nickel.

Table 5. Summary of results from nanoindentation of different phases set-up 1. Hardness in GPa.

Alloys α-dendrites aluminium-silicon eutectic

Al-7Si 0.86 ± 0.04 1.42 ± 0.13

Al-7Si-Co 0.87 ± 0.03 1.45 ± 0.11

Al-7Si-Co-Ni 0.91 ± 0.02 1.48 ± 0.10

Al-7Si-Co-Ni-Sr 0.91 ± 0.02 1.48 ± 0.10

Al-15Si - 1.45 ± 0.12

Al-15Si-Co-Ni - 1.55 ± 0.10

The purpose of the second set-up with a load of 200 mN, is to evaluate the hardness

properties in the alloys. The results from minimum 33 indentations are presented - see

Table 6. It is clear that the additions of cobalt and nickel to the alloys increases the

hardness both in the hypo- and hypereutectic alloys, in the Al-7Si-Co-Ni alloy by 34.5 %

and by 43 % in the Al-15Si-Co-Ni alloy. It seems probable that the increasing contiguity

of the 3D-network, caused by intermetallics and eutectic silicon are the reason for the

improvement of hardness in the Al-7Si-Co-Ni alloy. Similar findings with addition of

nickel has been reported by Kaya et al. [39]. The strontium in the Al-7Si-Co-Ni-Sr alloy

is modifying the silicon morphology to a well modified aluminium-silicon eutectic

structure. The Al-7Si-Co-Ni-Sr alloy show an improved hardness by 13 % compared

with the Al-7Si alloy, this is in accordance with results from Zamani et al. [21]. Although

the hardness in the Al-7Si-Co-Ni-Sr alloy is lower than in the Al-7Si-Co-Ni and Al-7Si-

Co alloys. This may be due to the effect of strontium on the silicon morphology that

reduces the strength of the 3D-network or that the addition of the strontium is depressing

both the nucleation and growth temperature of the eutectic reaction [26]. The depression

is changing the volume of α-dendrites and the aluminium-silicon eutectic. By using the

lever rule in the aluminium-silicon phase diagram it is clear that the volume of α-

dendrites increases with a depression of the eutectic reaction temperature.

Table 6. Summary of results from nanoindentation set-up 2.

Alloys Hardness

Al-7Si 0.20 GPa ± 0.038

Al-Si-Co 0.259 GPa ± 0.040

Al-7Si-Co-Ni 0.269 GPa ± 0.034

Al-7Si-Co-Ni-Sr 0.226 GPa ± 0.034

Al-15Si 0.28 GPa ± 0.034

Al-15Si-Co-Ni 0.40 GPa ± 0.052

Page 28: Development of aluminium-silicon alloys with improved ...1146050/FULLTEXT01.pdf · alloys have been investigated by several researchers during the last decade [1-3]. However, the

28

The effect of silicon on the hardness (Al-7Si and Al-15Si) is showing a significant

improvement by 40 %. This is in accordance with results in the literature [59]. Moreover,

the combined addition of cobalt and nickel to the hypereutectic alloy shows an improved

hardness by 43 %, which indicates an enormous potential.

Micro Vickers measurements were performed on all alloys to compare the results with

the hardness values from the nanoindentation - see Table 7. Five indentations were

conducted in each alloy.

Table 7. Summary of the results from Micro Vickers measurements.

The results from the Micro Vickers is following the same trend as the nanoindentation

with an increasing hardness - see Figure 16.

Figure 16. Hardness results from nanoindentation and the Micro Vickers in all alloys.

Alloys Vickers 500 mg SD

Al-7Si HV 73.9 1.5

Al-Si-Co HV 76.6 1.1

Al-7Si-Co-Ni HV 78.0 1.5

Al-7Si-Co-Ni-Sr HV 75.9 1.1

Al-15Si HV 87.4 1.8

Al-15Si-Co-Ni HV 103.0 1.5

Page 29: Development of aluminium-silicon alloys with improved ...1146050/FULLTEXT01.pdf · alloys have been investigated by several researchers during the last decade [1-3]. However, the

29

The effect of the long-term exposure at elevated temperature were evaluated on four

alloys with various exposure times at 240 °C. The evolution of hardness is presented -

see Figure 17. The results are clearly showing a rapid decrease in hardness during the

first 10 hours in all alloys. The result agrees with work by Zamani et al. [21]. After

prolonged exposure at 240 °C, is the alloys with combined addition of cobalt and nickel

showing a significant higher hardness, in the Al-7Si-Co-Ni alloy by 12 % and by 5 % in

the Al-15Si-Co-Ni alloy. This may be due to the thermally stable intermetallics phases in

the alloys. From the results, there is no clear trend if the hardness reach a steady state

after exposed at 240 °C for 1000 hours. Moreover, the alloys should be exposed to 240

°C for at least 1000 hours to be able to understand the alloys mechanical properties

during use at elevated temperatures.

Figure 17. The hardness evolution when the alloys is exposed to 240 °C for times up to 1000

hours.

Page 30: Development of aluminium-silicon alloys with improved ...1146050/FULLTEXT01.pdf · alloys have been investigated by several researchers during the last decade [1-3]. However, the

30

4.2.6 Differential scanning calorimetry

The alloys were investigated with a NETZSCH 404C Pegasus® to trace phase transformations occurring when the material is exposed to elevated temperatures. The results from the DSC measurements up to 600 °C is showing that an exothermic reaction occurs with a maximum around 230 °C in all alloys - see Figure 18. This reaction corresponds to the silicon precipitation [21]. Moreover, no more reaction occurs below 400 °C which indicate that the intermetallics phases in these alloys are thermally stable up to 400 °C. The silicon precipitation is the main reason for the hardness decrease during long-term exposure at elevated temperatures. Moreover, from the DSC curves it is also shown that the incipient melting of eutectic silicon start at 572 °C ± 3 in all alloys.

(a) (b)

Figure 18. DSC curves of the as-cast alloys with a heating rate of 5 K/min.(a) Hypoeutectic

alloys, (b) Hypereutectic alloys

Page 31: Development of aluminium-silicon alloys with improved ...1146050/FULLTEXT01.pdf · alloys have been investigated by several researchers during the last decade [1-3]. However, the

31

4.2.7 Thermal expansion

The coefficient of the thermal expansion (CTE) in the alloys were investigated using a

dilatometer with a heating rate of 5 K/min up to 570 °C. The CTE result of the Al-7Si is

24.5 *10−6𝐾−1, while the Al-7Si-Co-Ni alloy significant decreases the CTE by 11.5 % -

see Figure 19. This indicates that the combined addition of nickel and cobalt may

influence the interconnectivity of the 3D-network in the Al-7Si-Co-Ni alloy. However,

the addition of strontium in the Al-7Si-Co-Ni-Sr alloy increase the CTE with 3.6 %

compared with the Al-7Si alloy, this is because of the higher volume of α-dendrites due

to the depressed eutectic reaction temperature. The effect of silicon (Al-7Si and Al-15Si)

show a reduction of the CTE by 33.8 %. This result proposes that the silicon in the

hypereutectic alloy is well distributed and acts as a metal composite. However, results

from Stadler et al. [60] shows that increasing the silicon content from 7 wt.% to 12 wt.%

will reduce the CTE by 7 %. This indicates that the effect of silicon on the CTE is

significant larger between the silicon contents 12 - 15 wt.%. The precipitation of the

silicon is observed in all curves - see Figure 19.

(a) (b)

Figure 19. Thermal expansion curves of the as-cast alloys with a heating rate of 5 K/min. (a)

Hypoeutectic alloys, (b) Hypereutectic alloys.

.

Page 32: Development of aluminium-silicon alloys with improved ...1146050/FULLTEXT01.pdf · alloys have been investigated by several researchers during the last decade [1-3]. However, the

32

5 Conclusions

This thesis has focused on the effect of Co, Ni and Sr in two aluminium-silicon alloys (7 wt.% and 15 wt.%) Samples were produced by directional solidification giving a microstructure with SDAS ~10 μm. The results show:

1. The addition of cobalt and nickel in aluminium-silicon alloys show a good potential to improve the mechanical properties at elevated temperature. With a combined addition of nickel and cobalt the ultimate tensile strength increases by ~32 % at 230 °C in the hypoeutectic alloy, and it remains at 23 % higher after prolonged exposure in 1000 hours at 240 °C.

2. The combined addition of nickel and cobalt show an improvement in hardness by 43 % in the hypereutectic alloy.

3. The strontium addition in the hypoeutectic alloy provides a fully modified

eutectic structure and reduces the sizes of the nickel and cobalt rich phases significantly.

4. Intermetallic phases were formed by the addition of cobalt and nickel. These phases

are thermally stable up to 400 °C. 5. The thermal expansion is reduced with addition of cobalt and nickel by 11.5 % in

the hypoeutectic alloy and by 7.8 % in the hypereutectic alloy.

Page 33: Development of aluminium-silicon alloys with improved ...1146050/FULLTEXT01.pdf · alloys have been investigated by several researchers during the last decade [1-3]. However, the

33

6 Future work

• Investigate the mechanism behind the silicon modification in the hypoeutectic alloy with addition of cobalt and nickel.

• The 3D-network of the eutectic silicon and intermetallic phases in the alloys with different additions needs to be investigated by FIB, deep etching or serial sectioning of the material.

• The mechanism of poisoning the grain size with addition of cobalt and nickel

should be investigated. • Investigate the combined addition of cobalt and nickel in a commercial aluminium-

silicon alloy.

Page 34: Development of aluminium-silicon alloys with improved ...1146050/FULLTEXT01.pdf · alloys have been investigated by several researchers during the last decade [1-3]. However, the

34

7 References

1. Stadler, F., et al. The effect of Ni on the high-temperature strength of Al-Si cast

alloys. in Materials Science Forum. 2011. Trans Tech Publ.

2. Ceschini, L., et al., Effect of microstructure and overaging on the tensile behavior

at room and elevated temperature of C355-T6 cast aluminum alloy. Materials &

design, 2015. 83: p. 626-634.

3. Stadler, F., et al., Effect of main alloying elements on strength of Al–Si foundry

alloys at elevated temperatures. International Journal of Cast Metals Research,

2012. 25(4): p. 215-224.

4. Dwivedi, D., R. Sharma, and A. Kumar, Influence of silicon content and heat

treatment parameters on mechanical properties of cast Al–Si–Mg alloys.

International Journal of Cast Metals Research, 2006. 19(5): p. 275-282.

5. Kaufman, J.G., Parametric analyses of high-temperature data for aluminum

alloys. 2008: ASM International.

6. Donachie, M.J. and S.J. Donachie, Superalloys: a technical guide. 2002: ASM

international.

7. Knipling, K.E., D.C. Dunand, and D.N. Seidman, Criteria for developing

castable, creep-resistant aluminum-based alloys–A review. Zeitschrift für

Metallkunde, 2006. 97(3): p. 246-265.

8. Sha, M., et al., Effects of cobalt content on microstructure and mechanical

properties of hypereutectic Al–Si alloys. Materials Science and Engineering: A,

2012. 535: p. 258-263.

9. Ryabov, D., et al., Influence of cobalt alloying on structure and long-term

strength of Al–Cu–Mg–Ag alloy system. Inorganic Materials: Applied Research,

2017. 8(1): p. 159-165.

10. Choi, S.-H., et al., High temperature tensile deformation behavior of new heat

resistant aluminum alloy. Procedia Engineering, 2011. 10: p. 159-164.

11. Miller, W., et al., Recent development in aluminium alloys for the automotive

industry. Materials Science and Engineering: A, 2000. 280(1): p. 37-49.

12. Rakhmonov, J., G. Timelli, and F. Bonollo, The Effect of Transition Elements on

High‐Temperature Mechanical Properties of Al–Si Foundry Alloys–A Review.

Advanced Engineering Materials, 2016.

13. Drivealuminium. (www.drivealuminum.org).

14. Kaufman, J.G. and E.L. Rooy, Aluminum Alloy Castings. American Foundry

Society, Columbus, Ohio, 2004.

15. Askeland, D.R. and P.P. Phulé, The science and engineering of materials. 2003.

16. Zamani, M., S. Seifeddine, and A.E. Jarfors, High temperature tensile

deformation behavior and failure mechanisms of an Al–Si–Cu–Mg cast alloy—

The microstructural scale effect. Materials & design, 2015. 86: p. 361-370.

17. Campbell, J., Castings. 2003: Butterworth-Heinemann.

18. Jiang, W., et al., Effects of rare earth elements addition on microstructures,

tensile properties and fractography of A357 alloy. Materials Science and

Engineering: A, 2014. 597: p. 237-244.

19. Tenekedjiev, N. and J. Gruzleski, Hypereutectic aluminium-silicon casting

alloys—a review. Cast Metals, 1990. 3(2): p. 96-105.

20. Bogdanoff, T., S. Seifeddine, and A.K. Dahle, The effect of SI content on

microstructure and mechanical properties of Al-Si alloy. La Metallurgia Italiana,

2016. 108(6).

Page 35: Development of aluminium-silicon alloys with improved ...1146050/FULLTEXT01.pdf · alloys have been investigated by several researchers during the last decade [1-3]. However, the

35

21. Zamani, M., et al., The Role of Transition Metal Additions on the Ambient and

Elevated Temperature Properties of Al-Si Alloys. Materials Science and

Engineering: A, 2017.

22. Rakhmonov, J., G. Timelli, and F. Bonollo, The Effect of Transition Elements on

High-Temperature Mechanical Properties of Al–Si Foundry Alloys–A Review.

Advanced Engineering Materials, 2016. 18(7): p. 1096-1105.

23. Sepehrband, P., R. Mahmudi, and F. Khomamizadeh, Effect of Zr addition on the

aging behavior of A319 aluminum cast alloy. Scripta materialia, 2005. 52(4): p.

253-257.

24. Mahmudi, R., P. Sepehrband, and H. Ghasemi, Improved properties of A319

aluminum casting alloy modified with Zr. Materials Letters, 2006. 60(21): p.

2606-2610.

25. Di Sabatino, M., Fluidity of aluminium foundry alloys. 2005, Norwegian

University of Science and Technology.

26. Dahle, A., et al., Eutectic modification and microstructure development in Al–Si

Alloys. Materials Science and Engineering: A, 2005. 413: p. 243-248.

27. Liu, X., et al., Twin-controlled growth of eutectic Si in unmodified and Sr-

modified Al–12.7% Si alloys investigated by SEM/EBSD. Acta Materialia, 2015.

97: p. 338-347.

28. Timpel, M., et al., The role of strontium in modifying aluminium–silicon alloys.

Acta Materialia, 2012. 60(9): p. 3920-3928.

29. Makhlouf, M. and H. Guthy, The aluminum–silicon eutectic reaction:

mechanisms and crystallography. Journal of light metals, 2001. 1(4): p. 199-218.

30. Lasagni, F., et al., Three-dimensional characterization of ‘as-cast’and solution-

treated AlSi12 (Sr) alloys by high-resolution FIB tomography. Acta Materialia,

2007. 55(11): p. 3875-3882.

31. Dieter, G.E. and D.J. Bacon, Mechanical metallurgy. Vol. 3. 1986: McGraw-Hill

New York.

32. Seifeddine, S., E. Sjölander, and T. Bogdanoff, On the role of copper and cooling

rates on the microstructure, defect formations and mechanical properties of Al-

Si-Mg alloys. 2013.

33. Shabestari, S. and H. Moemeni, Effect of copper and solidification conditions on

the microstructure and mechanical properties of Al–Si–Mg alloys. Journal of

Materials Processing Technology, 2004. 153: p. 193-198.

34. Sharma, C.P., Engineering materials: properties and applications of metals and

alloys. 2003: PHI Learning Pvt. Ltd.

35. Jia, K., et al., Al–9.00% Si–0.25% Mg alloys modified by ytterbium. Rare Metals,

2017. 36(2): p. 95-100.

36. Xu, C., et al., Effect of Sc and Sr on the Eutectic Si Morphology and Tensile

Properties of Al-Si-Mg Alloy. Journal of Materials Engineering and Performance,

2017. 26(4): p. 1605-1613.

37. Naeem, H.T., K.S. Mohammed, and K.R. Ahmad, The Role of cobalt and nickel

intermetallic phases on the mechanical properties and microstructure evolution

of Al-Zn-Mg-Cu alloys. Materials Research, 2014. 17(6): p. 1663-1676.

38. Konečná, R., et al., The role of elevated temperature exposure on structural

evolution and fatigue strength of eutectic AlSi12 alloys. International Journal of

Fatigue, 2016. 83: p. 24-35.

39. Kaya, H. and A. Aker, Effect of alloying elements and growth rates on

microstructure and mechanical properties in the directionally solidified Al–Si–X

alloys. Journal of Alloys and Compounds, 2017. 694: p. 145-154.

Page 36: Development of aluminium-silicon alloys with improved ...1146050/FULLTEXT01.pdf · alloys have been investigated by several researchers during the last decade [1-3]. However, the

36

40. Spittle, J., Grain refinement in shape casting of aluminium alloys. 2006, Taylor &

Francis.

41. Samuel, A., et al., A Metallographic Study of Grain Refining of Sr-Modified 356

Alloy. International Journal of Metalcasting, 2016: p. 1-16.

42. Kasprzak, W., B.S. Amirkhiz, and M. Niewczas, Structure and properties of cast

Al–Si based alloy with Zr–V–Ti additions and its evaluation of high temperature

performance. Journal of Alloys and Compounds, 2014. 595: p. 67-79.

43. Greer, A., Overview: Application of heterogeneous nucleation in grain-refining of

metals. The Journal of Chemical Physics, 2016. 145(21): p. 211704.

44. Seifeddine, S., Characteristics of cast aluminium-silicon alloys: microstructures

and mechanical properties. 2006.

45. Samuel, A., et al., Effect of Sr-P Interaction on the Microstructure and Tensile

Properties of A413. 0 Type Alloys. Advances in Materials Science and

Engineering, 2016. 2016.

46. Dinnis, C.M., A.K. Dahle, and J.A. Taylor, Three-dimensional analysis of

eutectic grains in hypoeutectic Al–Si alloys. Materials Science and Engineering:

A, 2005. 392(1): p. 440-448.

47. Lu, L., K. Nogita, and A. Dahle, Combining Sr and Na additions in hypoeutectic

Al–Si foundry alloys. Materials Science and Engineering: A, 2005. 399(1): p. 244-

253.

48. Sigworth, G., The modification of Al-Si casting alloys: important practical and

theoretical aspects. International Journal of Metalcasting, 2008. 2(2): p. 19-40.

49. Wang, Q. and C. Caceres, The fracture mode in Al–Si–Mg casting alloys.

Materials Science and Engineering: A, 1998. 241(1): p. 72-82.

50. Fisher, K. and W. Kurz, Fundamentals of solidification. Trans Tech Publications,

1986.

51. Arnberg, L., et al., Solidification Characteristics of Aluminum Alloys: Dendrite

Coherency. 1996: American Foundrymen's Society.

52. Olofsson, J., et al., Characterisation and investigation of local variations in

mechanical behaviour in cast aluminium using gradient solidification, Digital

Image Correlation and finite element simulation. Materials & Design, 2014. 56:

p. 755-762.

53. Oliver, W.C. and G.M. Pharr, Measurement of hardness and elastic modulus by

instrumented indentation: Advances in understanding and refinements to

methodology. Journal of materials research, 2004. 19(01): p. 3-20.

54. Lee, Y., et al., The effect of grain refinement and silicon content on grain

formation in hypoeutectic Al–Si alloys. Materials Science and Engineering: A,

1999. 259(1): p. 43-52.

55. Qiu, D., et al., A mechanism for the poisoning effect of silicon on the grain

refinement of Al–Si alloys. Acta Materialia, 2007. 55(4): p. 1447-1456.

56. McDonald, S.D., K. Nogita, and A.K. Dahle, Eutectic nucleation in Al–Si alloys.

Acta Materialia, 2004. 52(14): p. 4273-4280.

57. Talaat, E.-B. and F. Hasse, Solidification Mechanism of Unmodified and

Strontium Modified Al–Si Alloys. Materials Transactions, JIM, 2000. 41(4): p.

507-515.

58. Rincon, E., et al., Effect of temperature on the tensile properties of an as-cast

aluminum alloy A319. Materials Science and Engineering: A, 2007. 452: p. 682-

687.

Page 37: Development of aluminium-silicon alloys with improved ...1146050/FULLTEXT01.pdf · alloys have been investigated by several researchers during the last decade [1-3]. However, the

37

59. Sharma, R. and D. Dwivedi, Influence of silicon (wt.%) and heat treatment on

abrasive wear behaviour of cast Al–Si–Mg alloys. Materials Science and

Engineering: A, 2005. 408(1): p. 274-280.

60. Stadler, F., et al., The effect of main alloying elements on the physical properties

of Al–Si foundry alloys. Materials Science and Engineering: A, 2013. 560: p. 481-

491.