December 06

ISO Update

Supplement to ISO Focus

December 2006/January 2007

People and places

ISO Members 2

Standardizing bodies having acceptedthe WTO TBT Code of Good Practicefor the Preparation, Adoption andApplication of Standards 5

International Standards in processfrom 26 October to 14 December 2006

Committee Drafts (CD) registered 6

Draft International Standards (DIS) circulated 7

Final draft International Standards (FDIS) circulated 12

Standards published 17

Standards confi rmed 30

Standards withdrawn 32

Meeting calendar 33

People and places

2 ISO Update, Supplement to ISO Focus – December 2006/January 2007

ISO Members

Since the November 2006 issue of ISO Focus, the following changes affecting ISO members have occurred :

Membership change

The Division de la Normalisation et de la Qualité (CDNQ) of Cameroon has been restored to its status as a correspondent member :

CAMEROON (CDNQ)

Division de la Normalisation et de la Qualité Ministère de l’Industrie, des Mines et du Développement technologique B.P. 5674 YAOUNDÉ

Chef de Division: M. Charles Booto à Ngon

Tel. +237 993 76 21 Fax +237 222 95 86 E-mail [email protected]

New CEO

Member bodies

BARBADOS (BNSI)

Acting Director: Mrs. Anthea Ishmael

BOSNIA AND HERZEGOVINA (BASMP)

Director: Mr. Goran Tesanovic

CYPRUS (CYS)

Director: Mr. Pambos Kammas

IRAN, ISLAMIC REPUBLIC OF (ISIRI)

President: Mr. Mohammad Nazemi Ardekani

MALAYSIA DSM)

Director General: Mrs. Fadilah Baharin

MAURITIUS (MSB)

Acting Director: Mrs. R. Nanhuck

POLAND (PKN)

President: Dr. Tomasz Schweitzer

SYRIAN ARAB REPUBLIC (SASMO)

General Director: Prof. Fouad Shoukri-Kourdi

Correspondent members

LATVIA (LVS)

Chairman of the Board: Mr. Visvaldis Zvejs

PERU (INDECOPI)

Gerente General: Ms. Ana María Capurro

Subscriber members

GUYANA (GNBS)

Executive Director: Dr. Chatterpaul Ramcharran

Address changes

Member bodies

ARMENIA (SARM)

National Institute of Standards Ministry of Trade and Economic Development Komitas Avenue 49/2 0051 YEREVAN

AUSTRIA (ON)

Österreichisches Normungsinstitut (ON) Austrian Standards Institute (ON) Heinestrasse 38 A–1020 WIEN

BANGLADESH (BSTI)

Web www.bsti.gov.bd

BELARUS (BELST)

Committee for Standardization of Belarus 93 Starovilensky tract MINSK 220053

BOSNIA AND HERZEGOVINA (BASMP)

Institute for Standards, Metrology and Intellectual Property of Bosnia and Herzegovina Institut za standarde, mjeriteljstvo i intelektualno viasnistvo BiH Hamdije Cemerlica 2 71000 SARAJEVO

Tel. + 387 33 65 27 81 Fax + 387 33 65 27 57 E-mail [email protected] Web www.basmp.gov.ba

ISO Update, Supplement to ISO Focus – December 2006/January 2007

BULGARIA (BDS)

Tel. + 359 2 81 74 504

COLOMBIA (ICONTEC)

E-mail [email protected]

CROATIA (HZN)


CYPRUS (CYS)

Web www.cys.org.cy

ETHIOPIA (QSAE)

Tel. + 251 11 646 08 81

FIJI (FTSQCO)

Fiji Trade Standards and Quality Control Office Ministry of Commerce and Industries Naibati House P O Box 2118 SUVA

Tel. + 679 3 30 54 11 Fax + 679 3 30 26 17 E-mail [email protected] Web www.pasc.standards.org.au

FRANCE (AFNOR)

Association française de normalisation 11, rue Francis de Pressensé F–93571 SAINT-DENIS LA PLAINE CEDEX

Tel. + 33 1 41 62 80 00 Fax + 33 1 49 17 90 00 E-mail [email protected] Web www.afnor.org

GHANA (GSB)

Ghana Standards Board South Legon Road ACCRA

Postal address

P.O. BOX MB 245 ACCRA

Tel. + 233 21 50 14 95 Fax + 233 21 50 00 92 E-mail [email protected] Web www.ghanastandards.org

ICELAND (IST)

Web www.ist.is

KAZAKHSTAN (KAZMEMST)

Committee for Technical Regulation and Metrology “Centre of Measurement Standards” # 35 str., building # 11 Left side of the Ishim River ASTANA CITY

Tel. + 7 3172 79 33 01 Fax + 7 3172 24 02 48 E-mail [email protected] Web www.memst.kz

KOREA, REPUBLIC OF (KATS)

Korean Agency for Technology and Standards 2, Jungang-dong, Gwacheon-si Seoul, GYEONGGI-DO 427-716

Tel. + 82 2 509 73 99 Fax + 82 2 509 73 44 E-mail [email protected] Web www.kats.go.kr

JAMAICA (JBS)

E-mail [email protected] Web www.bsj.org.jm

MOROCCO (SNIMA)

Service de Normalisation Industrielle Marocaine (SNIMA) Ministère de l'industrie, du commerce et de la mise à niveau de l'économie Angle Avenue Kamal Zebdi et Rue Dadi Secteur 21, Hay Riad 10100 RABAT

PANAMA (COPANIT)

Comisión Panameña de Normas Industriales y Técnicas Edificio Plaza Edison, Tercer Piso Avenida Ricardo J. Alfaro y Calle El Paical Apartado 0815-0119 PANAMA

Tel. + 507 560 0716 Fax + 507 560 0721 E-mail [email protected] Web www.mici.gob.pa

SWEDEN (SIS)

Swedish Standards Institute Sankt Paulsgatan 6 SE-118 46 STOCKHOLM

Postal address

SE-118 80 STOCKHOLM

THE FORMER YUGOSLAV REPUBLIC OF MACEDONIA (ISRM)

Web www.isrm.gov.mk

3

4 ISO Update, Supplement to ISO Focus – December 2006/January 2007

TUNISIA (INNORPI)

Tel. + 216 71 806 758 Fax + 216 71 807 071 E-mail [email protected] Web www.inorpi.ind.tn

TURKEY (TSE)

Tel. + 90 312 416 62 64 Fax + 90 312 416 66 10

UZBEKISTAN/(UZSTANDARD)

Fax + 998 71 396 71 93

Correspondent members

ANGOLA (IANORQ)

Tel. + 244 2 33 72 94 Fax + 244 2 39 67 45 E-mail [email protected]

BENIN (CEBENOR)

Centre Béninois de Normalisation et de Gestion de la Qualité Immeuble Trinité Quartier Avleketecondji, 1ère Von à droite Après le Carrefour Caboma COTONOU

Postal address

02 B.P. 1101 COTONOU


BURKINA FASO (FASONORM)

Direction de la Normalisation et de la Promotion de la Qualité Avenue de l’UEMOA Immeuble ONAC 01 BP : 389 OUAGADOUGOU 01

GEORGIA (GEOSTM)

Georgian National Agency for Standards, Technical Regulations and Metrology 67 Chargali Street TBILISI 0141

GUATEMALA (COGUANOR)

Tel. + 502 2476 6784-87 Fax + 502 2476 6777 E-mail [email protected] Web www.mineco.gob.gt

GUINEA (INNM)


GUINEA-BISSAU (DSNPQ)

Tel. + 245 722 27 27 Fax + 245 664 80 49

MACAU, China (CPTTM)

Tel. + 853 28 781 313 Fax + 853 28 788 233 E-mail [email protected] Web www.cpttm.org.mo

MALAWI (MBS)


MOLDOVA, REPUBLIC OF (MOLDST)

Department of Standardization and Metrology Str. Coca 28 or. CHISINAU MD-2064

Tel. + 373 22 74 85 88 Fax + 373 22 75 05 54 E-mail [email protected] Web www.standard.md

NAMIBIA (NSIQO)

Tel. + 264 61 283 73 32

NEPAL (NBSM)

Nepal Bureau of Standards and Metrology P.O. Box 985 Balaju KATHMANDU

Tel. + 977 14 35 68 10 Fax + 977 14 35 06 89 E-mail [email protected] Web www.nepalstandards.gov.np

NIGER (DNQM)


PERU (INDECOPI)


RWANDA (RBS)

Tel: + 250 58 6103

SENEGAL (ASN)

Association Sénégalaise de Normalisation Ministère de l'Industrie 122 bis, Avenue André Peytavin Boîte postale 4037 DAKAR

Tel. + 221 827 64 01 Fax + 221 827 64 12 E-mail [email protected] Web www.asn.sn

ISO Update, Supplement to ISO Focus – December 2006/January 2007 5

SEYCHELLES (SBS)

Seychelles Bureau of Standards Providence Industrial Estate MAHÉ

Postal address

P.O. Box 953 Victoria MAHÉ

Tel. + 248 38 04 00

Fax + 248 37 38 26 E-mail [email protected] Web www.seychelles.net/sbsorg

TOGO (CSN)

Conseil Supérieur de Normalisation CASEF 4e étage, Porte 456 B.P 383 LOMÉ

TURKMENISTAN (MSST)

The Major State Service “Turkmenstandartlary" 1995 str., Building-12 744000 ASHGABAT


Subscriber members

GRENADA (GDBS)


GUYANA (GNBS)

Guyana National Bureau of Standards Flat 15, Sophia Exhibition Complex Sophia GEORGETOWN

HONDURAS (COHCIT)

Consejo Hondureño de Ciencia y Tecnología (COHCIT) Boulevar Fuerzas Armadas Edificio CAD-COHCIT Contiguo a Museo Chiminike Apartado P. 4458 TEGUCIGALPA

Chief Executive: Mrs. Myriam Mejía

Tel + 504 228 61 95 Fax + 504 230 18 99 E-mail [email protected]

SAINT VINCENT AND THE GRENADINES (SVGBS)

E-mail [email protected] Web www.gov.vc/svgbs

Standardizing bodies having accepted the WTO* TBT* Code of Good Practice for the Preparation, Adoption and Application of Standards

Since publication of the November 2006 edition of the ISO Focus, the following standardizing body have notified the ISO/IEC Information Centre that they have accepted the Code of Good Practice for the Preparation, Adoption and Application of Standards presented in Annex 3 to the WTO Agreement on Technical Barriers to Trade. A complete list of the standardizing bodies having accepted the Code is available from the Standards and World Trade section of ISO Online: http://www.iso.org/iso/en/ commsmarkets/wto/iso+wto.html

Note: The work programmes of the standardizing bodies are available at the relevant standardizing body address if not indicated otherwise.

KAZAKHSTAN

Committee for Technical Regulation and Metrology of the Ministry and Industry of the Republic of Kazakhstan "Center of Measurement Standards" No. 35 str, bldg 11 ASTANA CITY

Tel: + (3172) 299 01 32 Telefax: + (3172) 24 13 03 E-mail: [email protected] Web: www.memst.kz

PAPUA NEW GUINEA

National Institute of Standards and Industrial Technology – NIST P.O. Box 3040 BOROKO NCD

Tel: + (675) 323 18 52 Telefax: + (675) 325 87 93 E-mail: [email protected] Web: www.nisit.gov.pg

__________________ * WTO – World Trade Organization TBT – Agreement on Technical Barriers to Trade

International Standards in process

An International Standard is the result of an agreement between themember bodies of ISO. A first important step towards an InternationalStandard takes the form of a committee draft (CD) - this is circulatedfor study within an ISO technical committee. When consensus hasbeen reached within the technical committee, the document is sent tothe Central Secretariat for processing as a draft InternationalStandard (DIS). The DIS requires approval by at least 75 % of themember bodies casting a vote.

CD registered

Period from 26 October to 14 December 2006These documents are currently under consideration in the technicalcommittee.They have been registered at the Central Secretariat.*Available in English only

TC 4 Rolling bearings

ISO/CD TS 16281

Rolling bearings – Methods for calculating the modified reference rating life for universally loaded rolling bearings

TC 10 Technical product documentation

ISO/CD TS 16952-10

Technical product documentation – Reference designation system – Part 10: Power plants

ISO/CD 27668-1

Gel ink ball pens and refills – Part 1: General use

TC 22 Road vehicles

ISO 2575:2004/DAmd 5

Road vehicles – Symbols for controls, indicators and tell-tales – Amendment 5

ISO 6487:2002/CD Amd 1

Road vehicles – Measurement techniques in impact tests – Instrumentation – Amendment 1: Road vehicles – Measurement techniques in impact tests – Instrumentation - Draft amendment 1 : Dynamic calibration of load transduceurs

ISO 6487:2002/CD Amd 2

Road vehicles – Measurement techniques in impact tests – Instrumentation – Amendment 2: Road vehicles – Measurement techniques in impact tests – Instrumentation - Draft amendment 2 : ADT temperature measurement

ISO/CD 9043 Mopeds – Measurement method for moments of inertia (Revision of ISO 9043:1991)

ISO/CD 11452-9

Road vehicles – Component test methods for electrical disturbances from narrowband radiated electromagnetic energy – Part 9: Portable transmitters

ISO/CD TR 14646

Road vehicles – Side impact testing of child restraint systems

ISO/CD 24997 Road vehicles – Measurement techniques in impact tests – HYBRID 3 chest potentiometer calibration procxedure

ISO/CD 26021-3

Road vehicles – End of life activation on on-board pyrotechnic devices – Part 3: Test requirements and specification

ISO/CD 26021-4

Road vehicles – End of life activation on on-board pyrotechnic devices – Part 4: Additional communication line with bidirectional communication

ISO/CD 26021-5

Road vehicles – End of life activation on on-board pyrotechnic devices – Part 5: Additional communication line with pulse width modulated signal

TC 23 Tractors and machinery for agriculture and forestry

ISO/CD 13457 Agricultural irrigation equipment – Water-driven chemical injector pumps (Revision of ISO 13457:2000)

TC 34 Food products

ISO/CD 6495-2 Animal feeding stuffs – Determination of water-soluble chlorides content – Part 2: Potentiometric method (Revision of ISO 6495:1999)

TC 37 Terminology and other language and content resources

ISO/CD 23185 Assessment and benchmarking of content resources for terminological data – General concepts, principles and requirements

TC 38 Textiles

ISO/CD 23606 Knitted fabrics – Representation and pattern design

TC 44 Welding and allied processes

ISO/CD 15011-2

Health and safety in welding and allied processes – Laboratory method for sampling fume and gases – Part 2: Determination of emission rates of gases, except ozone (Revision of ISO 15011-2:2003)

TC 45 Rubber and rubber products

ISO/CD 2322 Styrene-butadiene rubber (SBR) – Emulsion- and solution-polymerized types – Evaluation procedures (Revision of ISO 2322:1996)

ISO/CD 2476 Rubber, butadiene (BR) – Solution-polymerized types – Evaluation procedures (Revision of ISO 2476:1996)

TC 106 Dentistry

ISO/CD 4049 Dentistry – Polymer-based filling, restorative and luting materials (Revision of ISO 4049:2000)

ISO/CD 9917-2 Dental water-based cements – Part 2: Light-activated cements (Revision of ISO 9917-2:1998)

TC 119 Powder metallurgy

ISO/CD 26482 Hardmetals – Determination of lead and cadmium content

6 ISO Update, Supplement to ISO Focus - December 2006/January 2007

DIS circulated

Period from 26 October to 14 December 2006

These documents have obtained substantial support within theappropriate ISO technical committee

They have been submitted to the ISO member bodies for voting bythe date shown

*Available in English only

TC 127 Earth-moving machinery

ISO/CD 23727 Eart moving machinery – Coupling of attachments to medium sized four wheel drive loaders

TC 146 Air quality

ISO/CD 15767 Workplace atmospheres – Controlling and characterizing errors in weighing collected aerosols (Revision of ISO 15767:2003)

TC 147 Water quality

ISO/CD 25101 Water quality – Determination of perfluorooctanesulfonate (PFOS) and perfluorooctanoate (PFOA) in un-filtrated water samples – Method by solid phase extraction and liquid chromatograph-mass spectrometry

ISO/CD 27108 Water quality – Determination of selected plant treatment agents and biocide products – Method using gas chromatography (GC-MS) following solid-phase microextraction (SPME)

TC 164 Mechanical testing of metals

ISO/CD 1143 Metallic materials – Rotating bar bending fatigue testing (Revision of ISO 1143:1975)

ISO/CD 1352 Metallic materials – Torsional stress fatigue testing (Revision of ISO 1352:1977)

ISO/CD 27306 Metallic materials – Method of contraint loss correction of CTOD fracture toughness for fracture assessment of steel components

TC 165 Timber structures

ISO/CD 20152 Timber structures – Bond performance of adhesives – Basic requirements

TC 199 Safety of machinery

ISO/CD 29042-1

Safety of machinery – Evaluation of the emission of airborn hazardous substances – Part 1: Selection of test methods

TC 201 Surface chemical analysis

ISO/CD 15338 Surface chemical analysis – Glow-discharge mass spectrometry (GD-MS) – Introduction to use

ISO/CD 18117 Surface chemical analysis – Handling of specimens prior to analysis

TC 210 Quality management and corresponding general aspects for medical devices

ISO 15223-1/CD Amd 1

Medical devices – Symbols to be used with medical device labels, labelling and information to be supplied – Part 1: General requirements – Amendment 1

ISO/CD 15223-2

Medical devices – Symbols to be used with medical device labels, labelling and information to be supplied – Part 2: Symbol validation

TC 211 Geographic information/Geomatics

ISO 19110:2005/CD Amd 1

Geographic information – Methodology for feature cataloguing – Amendment 1

ISO/CD 19118 Geographic information – Encoding (Revision of ISO 19118:2005)

ISO/CD 19126 * Geographic information – Feature concept dictionaries and registers

ISO/CD 19142 Geographic information – Web Feature Service

TC 227 Springs

ISO/CD 26909 Springs – Glossary of spring terminology (Revision of ISO 2162-3:1993)

JTC 1 Information technology

ISO/IEC CD 24784

* Information Technology - Description of ISO/IEC 9995 issues regarding users needs and necessary innovations

Voteterminates

IULTCS International Union of Leather Technologists and Chemists Societies

ISO/DIS 11643 Leather – Tests for colour fastness – Colour fastness of small samples to solvents (Revision of ISO 11643:1993)

2007-05-14

ISO/DIS 11644 Leather – Test for adhesion of finish (Revision of ISO 11644:1993)

2007-05-07

TC 2 Fasteners

ISO/DIS 898-1 Mechanical properties of fasteners made of carbon steel and alloy steel – Part 1: Bolts, screws and studs (Revision of ISO 898-1:1999)

2007-04-30

TC 6 Paper, board and pulps

ISO/DIS 12625-10

* Tissue paper and tissue products – Part 10: Determination of demand water absorption rate and capacity, under controlled hydraulic pressure

2007-04-30

TC 8 Ships and marine technology

ISO/DIS 28003 * Security management systems for the supply chain - Requirements for bodies providing audit and certification of supply chain security management systems (Revision of ISO/PAS 28003:2006)

2007-05-07

TC 12 Quantities, units, symbols, conversion factors

IEC/DIS 80000-13

Quantities and units – Part 13: Information science and technology

2007-04-24

ISO Update, Supplement to ISO Focus - December 2006/January 2007 7

IEC/DIS 80000-14

Quantities and units – Part 14: Telebiometrics related to human physiology

2007-04-17

TC 17 Steel

ISO/DIS 4960 * Cold-reduced carbon steel strip with a carbon content over 0,25 % (Revision of ISO 4960:1999)

2007-04-23

ISO/DIS 5954 * Cold-reduced carbon steel sheet according to hardness requirements (Revision of ISO 5954:1998)

2007-04-09

TC 20 Aircraft and space vehicles

ISO/DIS 22666 * Space data and information transfer systems – AOS (advanced orbiting systems) space data link protocol (Revision of ISO 22666:2005)

2007-04-16

TC 22 Road vehicles

ISO/DIS 1585 * Road vehicles – Engine test code – Net power (Revision of ISO 1585:1992)

2007-05-08

ISO 2575:2004/DAmd 5

Road vehicles – Symbols for controls, indicators and tell-tales – Amendment 5

2007-05-01

ISO/DIS 6550-3 * Road vehicles – Sheath-type glow-plugs with conical seating and their cylinder head housing – Part 3: M10 glow-plugs (Revision of ISO 6550-3:2002)

2007-05-07

ISO/DIS 9129 * Motorcycles – Measurement methods for moments of inertia (Revision of ISO 9129:1988)

2007-04-17

ISO 11992-3:2003/DAmd 1

* Road vehicles – Interchange of digital information on electrical connections between towing and towed vehicles – Part 3: Application layer for equipment other than brakes and running gear – Amendment 1

2007-05-07

ISO/DIS 22241-4

* Diesel engines – NOx reduction agent AUS 32 – Part 4: Refilling interface

2007-05-08


ISO 4254-1:2005/DAmd 1

Agricultural machinery – Safety – Part 1: General requirements – Amendment 1

2007-04-02

TC 27 Solid mineral fuels

ISO/DIS 1952 * Solid mineral fuels – Determination of extractable metals in dilute hydrochloric acid (Revision of ISO 1952:1976)

2007-04-02

ISO/DIS 10329 * Coal – Determination of plastic properties – Constant-torque Giessler Plastometer method

2007-05-07

ISO/DIS 23499 * Coal – Determination of bulk density 2007-05-07

TC 28 Petroleum products and lubricants

ISO/DIS 15029-2

Petroleum and related products – Determination of spray ignition characteristics of fire-resistant fluids – Part 2: Spray test – Stabilized flame heat release spray method

2007-04-09

TC 29 Small tools

ISO/DIS 6752 Tools for pressing – Round punches with 60 degrees conical head and straight shank (Revision of ISO 6752:1984)

2007-05-18

TC 33 Refractories

ISO/DIS 8894-2 * Refractory materials – Determination of thermal conductivity – Part 2: Hot-wire method (parallel) (Revision of ISO 8894-2:1990)

2007-04-02

ISO/DIS 21068-1

Chemical analysis of silicon carbide containing raw materials and refractory products – Part 1: General information and sample preparation

2007-04-30

ISO/DIS 21068-2

Chemical analysis of silicon carbide containing raw materials and refractory products – Part 2: Determination of loss on ignition, total carbon, free carbon and silicon carbide, total and free silica and total and free silicon

2007-04-30

ISO/DIS 21068-3

Chemical analysis of silicon carbide containing raw materials and refractory products – Part 3: Determination of nitrogen, oxygen and metallic and oxidic constituants

2007-04-30

TC 34 Food products

ISO/DIS 8292-1 * Animal and vegetable fats and oils – Determination of solid fat content by pulsed NMR – Part 1: Direct method

2007-05-14

ISO/DIS 8292-2 * Animal and vegetable fats and oils – Determination of solid fat content by pulsed NMR – Part 2: Indirect method

2007-05-14

ISO/DIS 13906 Animal feeding stuffs – Determination of acid detergent fibre (ADF) and acid detergent lignin (ADL) contents

2007-04-09

ISO/DIS 15302 * Animal and vegetable fats and oils – Determination of benzo[a]pyrene content – Reverse-phase high-performance liquid chromatography method (Revision of ISO 15302:1998)

2007-05-07

ISO/DIS 24333 Cereals and cereal products – Sampling

2007-03-26

ISO/DIS 27107 * Animal and vegetable fats and oils – Determination of peroxide value – Potentiometric endpoint determination

2007-05-07


ISO/DIS 12620 * Terminology and other content and language resources – Data categories – Specification of data categories and management of a Data Category Registry for language resources (Revision of ISO 12620:1999)

2007-05-21


TC 38 Textiles

ISO/DIS 105-E04

Textiles – Tests for colour fastness – Part E04: Colour fastness to perspiration (Revision of ISO 105-E04:1994, ISO 105-E04:1994/Cor 1:2002)

2007-04-09

TC 39 Machine tools

ISO/DIS 369 Machine tools – Symbols for indications appearing on machine tools (Revision of ISO/R 369:1964)

2007-05-14


ISO/DIS 14744-1

Welding – Acceptance inspection of electron beam welding machines – Part 1: Principles and acceptance conditions (Revision of ISO 14744-1:2000)

2007-05-21

ISO/DIS 15616-4

Acceptance tests for CO2-laser beam machines for high quality welding and cutting – Part 4: Using 2D moving optics type (Revision of ISO/TS 17477:2003)

2007-05-07

ISO/DIS 24373 Welding consumables – Solid wires and rods for fusion welding of copper and copper alloys – Classification

2007-04-02


ISO/DIS 7781 * Styrene-butadiene rubber, raw – Determination of soap and organic-acid content (Revision of ISO 7781:2001)

2007-05-11

ISO/DIS 17564 * Hydrogenated nitrile rubber (HNBR) – Determination of residual unsaturation by iodine value (Revision of ISO 17564:2001)

2007-05-11

TC 58 Gas cylinders

ISO 5145:2004/DAmd 2

* Cylinder valve outlets for gases and gas mixtures – Selection and dimensioning – Amendment 2

2007-05-07

TC 61 Plastics

ISO/DIS 1922 * Rigid cellular plastics – Determination of shear strength (Revision of ISO 1922:2001)

2007-05-07

ISO/DIS 8873-2 * Rigid cellular plastics – Spray-applied polyurethane foam for thermal insulation – Part 2: Application (Revision of ISO/PRF 8873-2)

2007-05-14

ISO/DIS 8873-3 * Rigid cellular plastics – Spray-applied polyurethane foam for thermal insulation – Part 3: Test methods (Revision of ISO/PRF 8873-3)

2007-05-14

ISO 9994:2005/DAmd 1

* Lighters – Safety specification – Amendment 1

2007-05-14

ISO/DIS 10840 * Plastics – Guidance for the use of standard fire tests (Revision of ISO 10840:2003)

2007-05-14

ISO/DIS 23560 * Woven polypropylene sacks for bulk packaging of foodstuffs

2007-04-02

ISO/DIS 24538 * Plastics – Homopolymer and copolymer resins of vinyl chloride – Determination of residual vinyl chloride monomer – Gas-chromatographic method on dry powder

2007-04-02

ISO/DIS 25761 * Plastics – Polyols for use in the production of polyurethanes – Determination of basicity (total amine value) as percent nitrogen

2007-05-18

ISO/DIS 26603 * Plastics – Aromatic isocyanates for use in the production of polyurethanes – Determination of total chlorine

2007-05-14

TC 67 Materials, equipment and offshore structures for petroleum, petrochemical and natural gas industries

ISO/DIS 13680 * Petroleum and natural gas industries – Corrosion-resistant alloy seamless tubes for use as casing, tubing and coupling stock – Technical delivery conditions (Revision of ISO 13680:2000, ISO 13680:2000/Cor 1:2002, ISO 13680:2000/Cor 2:2004)

2007-05-14

ISO/DIS 28300 * Petroleum, petrochemical and natural gas industries – Venting of atmospheric and low-pressure storage tanks

2007-04-23

TC 69 Applications of statistical methods

ISO/DIS 24153 * Random sampling and randomization procedures

2007-04-02

TC 70 Internal combustion engines

ISO/DIS 8178-2 Reciprocating internal combustion engines – Exhaust emission measurement – Part 2: Measurement of gaseous and particulate exhaust emissions under field conditions (Revision of ISO 8178-2:1996)

2007-04-09

TC 85 Nuclear energy

ISO/DIS 18213-3

Nuclear fuel technology – Tank calibration and volume determination for nuclear materials accountancy – Part 3: Statistical methods

2007-04-02

TC 92 Fire safety

ISO/DIS 13943 * Fire safety – Vocabulary (Revision of ISO 13943:2000)

2007-04-16

TC 94 Personal safety – Protective clothing and equipment

ISO/DIS 11612.2

Protective clothing – Clothing to protect against heat and flame (Revision of ISO 11612:1998)

2007-02-14

TC 96 Cranes

ISO/DIS 10245-1

Cranes – Limiting and indicating devices – Part 1: General (Revision of ISO 10245-1:1994)

2007-05-01


ISO/DIS 10245-3

Cranes – Limiting and indicating devices – Part 3: Tower cranes (Revision of ISO 10245-3:1999)

2007-05-01

ISO/DIS 11660-1

Cranes – Access, guards and restraints – Part 1: General (Revision of ISO 11660-1:1999)

2007-03-27

ISO/DIS 11660-3

Cranes – Access, guards and restraints – Part 3: Tower cranes (Revision of ISO 11660-3:1999)

2007-03-27

TC 102 Iron ore and direct reduced iron

ISO/DIS 2597-2 * Iron ores – Determination of total iron content – Part 2: Titrimetric methods after titanium(III) chloride reduction

2007-05-11

ISO/DIS 15633 * Iron ores – Determination of nickel – Flame atomic absorption spectrometric method

2007-05-11

TC 104 Freight containers

ISO 1496-1:1990/DAmd 6

* Series 1 freight containers – Specification and testing – Part 1: General cargo containers for general purposes – Amendment 6: Racking test for 45 ft containers

2007-04-16

ISO/DIS 17712 Freight containers – Mechanical seals (Revision of ISO/PAS 17712:2006)

2007-05-01

TC 106 Dentistry

ISO/DIS 3950 * Dentistry – Designation system for teeth and areas of the oral cavity (Revision of ISO 3950:1984)

2007-04-30

ISO/DIS 6360-5 * Dentistry – Number coding system for rotary instruments – Part 5: Specific characteristics of root-canal instruments

2007-04-09

ISO/DIS 11143 * Dental equipment – Amalgam separators (Revision of ISO 11143:1999, ISO 11143:1999/Cor 1:2002)

2007-05-14

TC 108 Mechanical vibration and shock

ISO/DIS 10816-7

* Mechanical vibration – Evaluation of machine vibration by measurements on non-rotating parts – Part 7: Rotodynamic pumps for industrial applications, including measurements on rotating shafts

2007-05-18


ISO/DIS 3907 * Hardmetals – Determination of total carbon content – Gravimetric method (Revision of ISO 3907:1985)

2007-04-02

ISO/DIS 3908 * Hardmetals – Determination of insoluble (free) carbon content – Gravimetric method (Revision of ISO 3908:1985)

2007-04-02

TC 121 Anaesthetic and respiratory equipment

ISO/DIS 26825 * Anaesthetic and respiratory equipment – User-applied labels for syringes containing drugs used during anaesthesia – Colours, design and performance

2007-04-02

ISO/DIS 81060-1

Non-invasive sphygmomanometers – Part 1: Requirements and test methods for non-automated measurement type

2007-05-07

TC 122 Packaging

ISO/DIS 17366.2

* Supply chain applications of RFID – Product packaging

2007-02-08

ISO/DIS 17367.2

* Supply chain applications of RFID – Product tagging

2007-02-08

ISO/DIS 28219 * Packaging – Labelling and direct product marking with linear bar code and two-dimensional symbols

2007-05-07

TC 123 Plain bearings

ISO/DIS 7146-1 * Fluid film metallic plain bearings – Terms and characteristics of damage – Part 1: General (Revision of ISO 7146:1993)

2007-04-23

ISO/DIS 7146-2 * Fluid film metallic plain bearings – Description and characterization of damage – Part 2: Cavitation erosion and its countermeasures (Revision of ISO 7146:1993)

2007-05-21


ISO/DIS 16754 * Earth-moving machinery – Determination of average ground pressure – Crawler machines

2007-05-14

TC 130 Graphic technology

ISO/DIS 2834-2 * Graphic technology – Laboratory preparation test prints – Part 2: Liquid printing inks (Revision of ISO 2834:1999, ISO 2834:1999/Cor 1:2003)

2007-04-23

ISO/DIS 2846-2.2

* Graphic technology – Colour and transparency of printing ink sets for four-colour printing – Part 2: Coldset offset lithographic printing (Revision of ISO 2846-2:2000)

2007-02-12

TC 131 Fluid power systems

ISO/DIS 15086-3

Hydraulic fluid power – Determination of the fluid-borne noise characteristics of components and systems – Part 3: Measurement of hydraulic impedance

2007-05-07

TC 135 Non-destructive testing

ISO/DIS 3452-5 * Non-destructive testing – Penetrant testing – Part 5: Penetrant testing at temperatures higher than 50 degrees C

2007-04-30

ISO/DIS 3452-6 * Non-destructive testing – Penetrant testing – Part 6: Penetrant testing at temperatures lower than 10 degrees C

2007-04-30

ISO/DIS 11699-1

Non-destructive testing – Industrial radiographic film – Part 1: Classification of film systems for industrial radiography (Revision of ISO 11699-1:1998)

2007-05-14


TC 138 Plastics pipes, fittings and valves for the transport of fluids

ISO/DIS 18373-2

* Rigid PVC pipes – Differential scanning calorimetry (DSC) method – Part 2: Measurement of the enthalpy of fusion of crystallites

2007-05-07

TC 146 Air quality

ISO/DIS 16000-16

Indoor air – Part 16: Detection and enumeration of moulds – Sampling by filtration

2007-04-23

ISO/DIS 16000-17

Indoor air – Part 17: Detection and enumeration of moulds – Culture-based method

2007-04-23


ISO/DIS 5667-20

* Water quality – Sampling – Part 20: Guidance on the use of sampling data for decision making – Compliance with thresholds and classification systems

2007-04-09

TC 155 Nickel and nickel alloys

ISO/DIS 22725 Nickel alloys – Determination of tantalum – Inductively coupled plasma atomic emission spectrometric method

2007-04-16

TC 159 Ergonomics

ISO/DIS 9241-304

* Ergonomics of human-system interaction – Part 304: User performance test methods

2007-04-30

TC 165 Timber structures

ISO/DIS 12579.2

* Timber structures – Glued laminated timber – Method of test for shear strength of glue lines

2007-02-05

ISO/DIS 12580.2

* Timber structures – Glued laminated timber – Method of test for glue line delamination

2007-02-05

ISO/DIS 19993 * Timber structures – Glued laminated timber – Face and edge joint cleavage test

2007-04-10

TC 171 Document management applications

ISO/DIS 12651-1

* Electronic document management – Vocabulary – Part 1: Electronic document imaging (Revision of ISO 12651:1999)

2007-05-13

ISO/DIS 24517-1

* Document management – Engineering document format using PDF – Part 1: Use of PDF 1.6 (PDF/E-1)

2007-03-27

TC 172 Optics and photonics

ISO/DIS 10110-14

Optics and photonics – Preparation of drawings for optical elements and systems – Part 14: Wavefront deformation tolerance (Revision of ISO 10110-14:2003)

2007-04-16

ISO/DIS 10110-5

Optics and photonics – Preparation of drawings for optical elements and systems – Part 5: Surface form tolerances (Revision of ISO 10110-5:1996, ISO 10110-5:1996/Cor 1:1996)

2007-04-10

ISO/DIS 14132-5

Optics and photonics – Vocabulary for telescopic systems – Part 5: Terms for night vision devices

2007-05-14

TC 188 Small craft

ISO/DIS 10088 * Small craft – Permanently installed fuel systems (Revision of ISO 10088:2001)

2007-05-11

ISO/DIS 16180.3

Small craft – Electric navigation lights

2007-01-09

TC 190 Soil quality

ISO/DIS 19730 Soil quality – Extraction of trace elements using ammonium nitrate solution

2007-04-16

ISO/DIS 22036 Soil quality – Determination of trace elements in extracts of soil by inductively coupled plasma - atomic emission spectrometry (ICP - AES)

2007-04-16

TC 193 Natural gas

ISO/DIS 15970 * Natural gas – Measurement of properties – Volumetric properties: density, pressure, temperature and compression factor

2007-05-14

ISO/DIS 15971 * Natural gas – Measurement of properties – Combustion properties – Calorific value and Wobbe index

2007-05-18

TC 194 Biological evaluation of medical devices

ISO/DIS 10993-1

* Biological evaluation of medical devices – Part 1: Evaluation and testing within a risk management system (Revision of ISO 10993-1:2003)

2007-04-02

TC 195 Building construction machinery and equipment

ISO/DIS 15878.2

* Road construction and maintenance equipment – Asphalt pavers – Terminology and commercial specifications

2007-01-09

TC 202 Microbeam analysis

ISO/DIS 22493 * Microbeam analysis – Scanning electron microscopy – Vocabulary

2007-04-16

TC 204 Intelligent transport systems

ISO/DIS 21212 * Intelligent transport systems – Communications, air-interface, long and medium range (CALM) – 2G Cellular systems

2007-05-11

ISO/DIS 21213 * Intelligent transport systems – Communications, air-interface, long and medium range (CALM) – 3G Cellular systems

2007-05-11


FDIS circulated


These Final draft International Standards have been submitted to theISO member bodies for formal approval by the date shown


TC 207 Environmental management

ISO/DIS 14050 Environmental management – Vocabulary (Revision of ISO 14050:2002)

2007-05-18

TC 212 Clinical laboratory testing and in vitro diagnostic test systems

ISO/DIS 18113-1

* Clinical laboratory testing and in vitro diagnostic medical systems – Information supplied by the manufacturer (labelling) – Part 1: Terms, definitions and general requirements

2007-04-30

ISO/DIS 18113-2

* Clinical laboratory testing and in vitro diagnostic medical systems – Information supplied by the manufacturer (labelling) – Part 2: In vitro diagnostic reagents for professional use

2007-04-30

ISO/DIS 18113-3

* Clinical laboratory testing and in vitro diagnostic medical systems – Information supplied by the manufacturer (labelling) – Part 3: In vitro diagnostic instruments for professional use

2007-04-30

ISO/DIS 18113-4

* Clinical laboratory testing and in vitro diagnostic medical systems – Information supplied by the manufacturer (labelling) – Part 4: In vitro diagnostic reagents for self-testing

2007-04-30

ISO/DIS 18113-5

* Clinical laboratory testing and in vitro diagnostic medical systems – Information supplied by the manufacturer (labelling) – Part 5: In vitro diagnostic instruments for self-testing

2007-04-30

TC 217 Cosmetics

ISO/DIS 15819 * Cosmetics – Analytical methods – Nitrosamines: Detection and determination of N-nitrosodiethanolamine (NDELA) in cosmetics by HPLC-MS

2007-05-08

TC 219 Floor coverings

ISO/DIS 4918 Resilient, textile and laminate floor coverings – Castor chair test (Revision of ISO/TR 4918:1990)

2007-04-23

TMB Technical Management Board

ISO/DGuide 78 Safety of machinery – Rules for drafting and presentation of safety standards

2007-03-24

ISO Guide 98:1995/DSuppl 1.2

* Guide to the expression of uncertainty in measurement (GUM) – Supplement 1: Propagation of

distributions using a Monte Carlo method

2007-01-03


ISO/IEC DIS 29341

* Information technology – UPnP Device Architecture 1.0

2007-06-18

ISO/IEC DIS 29361

* Information technology – Basic Profile Version 1.1

2007-06-18

ISO/IEC DIS 29362

* Information technology – Attachments Profile Version 1.0

2007-06-18

ISO/IEC DIS 29363

* Information technology – Simple SOAP Binding Profile Version 1.0

2007-06-18

Voteterminates

TC 2 Fasteners

ISO/FDIS 8748 Spring-type straight pins – Coiled, heavy duty (Revision of ISO 8748:1997)

2007-02-21

ISO/FDIS 8750 Spring-type straight pins – Coiled, standard duty (Revision of ISO 8750:1997)

2007-02-21

ISO/FDIS 8751 Spring-type straight pins – Coiled, light duty (Revision of ISO 8751:1997)

2007-02-21

TC 4 Rolling bearings

ISO/FDIS 281 Rolling bearings – Dynamic load ratings and rating life (Revision of ISO 281:1990, ISO 281:1990/Amd 1:2000, ISO/TS 16799:1999, ISO 281:1990/Amd 2:2000)

2006-12-26

ISO/FDIS 1224-2

Rolling bearings – Instrument precision bearings – Part 2: Characteristics of inch series bearings (Revision of ISO 1224:1984)

2007-01-13


ISO/FDIS 3037 Corrugated fibreboard – Determination of edgewise crush resistance (unwaxed edge method) (Revision of ISO 3037:1994)

2007-01-30

ISO/FDIS 12625-7

Tissue paper and tissue products – Part 7: Determination of optical properties

2007-01-16


ISO/FDIS 8468 * Ships and marine technology – Ship's bridge layout and associated equipment – Requirements and guidelines (Revision of ISO 8468:1990, ISO 14612:2004)

2007-01-02

TC 22 Road vehicles

ISO/FDIS 15500-20

* Road vehicles – Compressed natural gas (CNG) fuel system components – Part 20: Rigid fuel line in material other than stainless steel

2007-02-20



ISO/FDIS 6534 Forestry machinery – Portable chain-saw hand-guards – Mechanical strength (Revision of ISO 6534:1992)

2007-02-14

ISO 11681-1:2004/FDAmd 1

Machinery for forestry – Portable chain-saw safety requirements and testing – Part 1: Chain-saws for forest service – Amendment 1: Balance

2007-02-21

ISO/FDIS 11783-13

* Tractors and machinery for agriculture and forestry – Serial control and communications data network – Part 13: File server

2007-01-10

ISO/FDIS 19732 Equipment for crop protection – Sprayer strainers – Colour coding for identification

2007-02-04

ISO/FDIS 22522 Crop protection equipment – Field measurement of spray distribution in tree and bush crops

2007-01-24

TC 24 Sieves, sieving and other sizing methods

ISO/FDIS 15901-3

* Pore size distribution and porosity of solid materials by mercury porosimetry and gas adsorption – Part 3: Analysis of micropores by gas adsorption

2007-02-04

TC 29 Small tools

ISO/FDIS 22037 Solid end mills with corner radii and cylindrical shanks made of hard cutting materials – Dimensions

2007-01-13

TC 30 Measurement of fluid flow in closed conduits

ISO/FDIS 2186 * Fluid flow in closed conduits – Connections for pressure signal transmissions between primary and secondary elements (Revision of ISO 2186:1973)

2007-01-22

TC 33 Refractories

ISO/FDIS 21587-1

Chemical analysis of aluminosilicate refractory products (alternative to the X-ray fluorescence method) – Part 1: Apparatus, reagents, dissolution and gravimetric silica

2007-01-13

ISO/FDIS 21587-2

Chemical analysis of aluminosilicate refractory products (alternative to the X-ray fluorescence method) – Part 2: Wet chemical analysis

2007-01-13

ISO/FDIS 21587-3

Chemical analysis of aluminosilicate refractory products (alternative to the X-ray fluorescence method) – Part 3: Inductively coupled plasma and atomic absorption spectrometry methods

2007-01-13

TC 34 Food products

ISO/FDIS 5518 * Fruits, vegetables and derived products – Determination of benzoic acid content – Spectrophotometric method (Revision of ISO 5518:1978)

2007-01-02

TC 35 Paints and varnishes

ISO/FDIS 2409 Paints and varnishes – Cross-cut test (Revision of ISO 2409:1992)

2007-01-30

ISO/FDIS 16276-1

Corrosion protection of steel structures by protective paint systems – Assessment of, and acceptance criteria for, the adhesion/cohesion (fracture strength) of a coating – Part 1: Pull-off testing

2007-01-30

ISO/FDIS 16276-2

Corrosion protection of steel structures by protective paint systems – Assessment of, and acceptance criteria for, the adhesion/cohesion (fracture strength) of a coating – Part 2: Cross-cut testing and X-cut testing

2007-01-30

ISO/FDIS 17872 Paints and varnishes – Guidelines for the introduction of scribe marks through coatings on metallic panels for corrosion testing

2007-01-16


ISO/FDIS 1951 Presentation/representation of entries in dictionaries – Requirements, recommendations and information (Revision of ISO 1951:1997)

2007-01-21

TC 38 Textiles

ISO/FDIS 105-J05

Textiles – Tests for colour fastness – Part J05: Method for the instrumental assessment of the colour inconstancy of a specimen with change in illuminant (CMCCON02)

2007-01-30

ISO/FDIS 3759 Textiles – Preparation, marking and measuring of fabric specimens and garments in tests for determination of dimensional change (Revision of ISO 3759:1994, ISO 3759:1994/Cor 1:1999, ISO 3759:1994/Cor 2:2004)

2007-02-14

ISO/FDIS 5077 Textiles – Determination of dimensional change in washing and drying (Revision of ISO 5077:1984)

2006-12-31

ISO/FDIS 18692 Fibre ropes for offshore stationkeeping – Polyester

2007-01-27

ISO/FDIS 23733 Textiles – Chenille yarns – Test method for the determination of linear density

2007-02-07

TC 39 Machine tools

ISO/FDIS 230-3 Test code for machine tools – Part 3: Determination of thermal effects (Revision of ISO 230-3:2001)

2007-02-06

ISO/FDIS 10791-10

Test conditions for machining centres – Part 10: Evaluation of thermal distortions

2006-12-31

TC 43 Acoustics

ISO/FDIS 5130 * Acoustics – Measurements of sound pressure level emitted by stationary road vehicles (Revision of ISO 5130:1982)

2007-02-21



ISO/FDIS 18594* Resistance spot-, projection- and seam-welding – Method for determining the transition resistance on aluminium and steel material

2007-01-16


ISO/FDIS 1138 Rubber compounding ingredients – Carbon black – Determination of sulfur content (Revision of ISO 1138:1981; ISO 1138:1981/DAmd 1)

2007-01-22

TC 46 Information and documentation

ISO/FDIS 9230 Information and documentation – Determination of price indexes for print and electronic media purchased by libraries (Revision of ISO 9230:1991)

2007-02-14

TC 61 Plastics

ISO/FDIS 307 * Plastics – Polyamides – Determination of viscosity number (Revision of ISO 307:2003)

2007-02-07

ISO/FDIS 17194.2

Structural adhesives – A standard database of properties

2007-02-01

ISO/FDIS 18872* Plastics – Determination of tensile properties at high strain rates

2007-01-24


ISO/FDIS 10441* Petroleum, petrochemical and natural gas industries – Flexible couplings for mechanical power transmission – Special-purpose applications (Revision of ISO 10441:1999)

2007-01-30

ISO/FDIS 15546 Petroleum and natural gas industries – Aluminium alloy drill pipe (Revision of ISO 15546:2002)

2007-02-14

ISO/FDIS 16812* Petroleum, petrochemical and natural gas industries – Shell-and-tube heat exchangers (Revision of ISO 16812:2002)

2007-01-02

TC 68 Financial services

ISO/FDIS 13616-1

* Financial services - International bank account number (IBAN) – Part 1: Structure of the IBAN (Revision of ISO 13616:2003)

2007-01-29

ISO/FDIS 13616-2

* Financial services - International bank account number (IBAN) – Part 2: Role and responsibilities of the Registration Authority (Revision of ISO 13616:2003)

2007-01-29

TC 76 Transfusion, infusion and injection equipment for me-dical and pharmaceutical use

ISO/FDIS 8536-4

* Infusion equipment for medical use – Part 4: Infusion sets for single use, gravity feed (Revision of ISO 8536-4:2004)

2007-02-14

ISO/FDIS 22413* Transfer sets for pharmaceutical preparations – Requirements and test methods

2007-02-01

TC 83 Sports and recreational equipment

ISO/FDIS 8364 Alpine skis and bindings – Binding mounting area – Requirements and test methods (Revision of ISO 8364:1999)

2007-02-04

TC 85 Nuclear energy

ISO/FDIS 9005 Nuclear energy – Uranium dioxide powder and sintered pellets – Determination of oxygen/uranium atomic ratio by the amperometric method (Revision of ISO 9005:1994)

2007-01-22

TC 89 Wood-based panels

ISO/FDIS 12465 Plywood – Specifications (Revision of ISO/DIS 12465-2, ISO/DIS 12465-3, ISO/DIS 12465-1)

2007-02-01

TC 92 Fire safety

ISO/FDIS 13571* Life-threatening components of fire – Guidelines for the estimation of time available for escape using fire data (Revision of ISO/TS 13571:2002)

2006-12-30

TC 96 Cranes

ISO/FDIS 10972-4

Cranes – Requirements for mechanisms – Part 4: Jib cranes

2007-02-15

ISO/FDIS 12480-4

Cranes – Safe use – Part 4: Jib cranes

2007-01-22

TC 110 Industrial trucks

ISO/FDIS 2328 Fork-lift trucks – Hook-on type fork arms and fork arm carriages – Mounting dimensions (Revision of ISO 2328:1993, ISO 5057:1993, ISO 2330:2002)

2007-01-29


ISO/FDIS 2740 * Sintered metal materials, excluding hardmetals – Tensile test pieces (Revision of ISO 2740:1999)

2007-01-09

ISO/FDIS 13947* Metallic powders – Test method for the determination of non-metallic inclusions in metal powders using a powder-forged specimen

2007-01-08


ISO/FDIS 7396-1

Medical gas pipeline systems – Part 1: Pipeline systems for compressed medical gases and vacuum (Revision of ISO 7396-1:2002)

2007-01-23

ISO/FDIS 7396-2

* Medical gas pipeline systems – Part 2: Anaesthetic gas scavenging disposal systems (Revision of ISO 7396-2:2000)

2007-02-14


ISO/FDIS 7451 Earth-moving machinery – Volumetric ratings for hoe-type and grab-type buckets of hydraulic excavators and backhoe loaders (Revision of ISO 7451:1997, ISO 7451:1997/Cor 1:1998)

2007-01-24



ISO/FDIS 12643-1

* Graphic technology – Safety requirements for graphic technology equipment and systems – Part 1: General requirements (Revision of ISO 12649:2004, ISO 12648:2006)

2007-01-14

ISO/FDIS 12643-2

* Graphic technology – Safety requirements for graphic technology equipment and systems – Part 2: Press equipment and systems (Revision of ISO 12648:2006)

2007-02-15


ISO/FDIS 13950 Plastics pipes and fittings – Automatic recognition systems for electrofusion joints (Revision of ISO/TR 13950:1997)

2006-12-31

TC 145 Graphical symbols

ISO 7010:2003/FDAmd 5.2

Graphical symbols – Safety colours and safety signs – Safety signs used in workplaces and public areas – Amendment 5: Safety sign M003: Wear ear protection

2007-01-23

ISO 7010:2003/FDAmd 6.2

Graphical symbols – Safety colours and safety signs – Safety signs used in workplaces and public areas – Amendment 6: Safety sign M004: Wear eye protection

2007-01-23


ISO/FDIS 17858* Water quality – Determination of dioxin-like polychlorinated biphenyls – Method using gas chromatography/mass spectrometry

2006-12-31

TC 150 Implants for surgery

ISO/FDIS 14607 Non-active surgical implants – Mammary implants – Particular requirements (Revision of ISO 14607:2002)

2006-12-26

TC 159 Ergonomics

ISO/FDIS 11228-2

Ergonomics – Manual handling – Part 2: Pushing and pulling

2007-02-04

ISO/FDIS 11228-3

Ergonomics – Manual handling – Part 3: Handling of low loads at high frequency

2007-02-04

ISO/FDIS 15536-2

Ergonomics – Computer manikins and body templates – Part 2: Verification of functions and validation of dimensions for computer manikin systems

2007-01-16


ISO/FDIS 24537* Micrographics – Dimensions for reels used for 16 mm and 35 mm microfilm

2007-01-28


ISO/FDIS 10934-2

* Optics and optical instruments – Vocabulary for microscopy – Part 2: Advanced techniques in light microscopy

2007-02-01

ISO/FDIS 11553-2

Safety of machinery – Laser processing machines – Part 2: Safety requirements for hand-held laser processing devices

2007-01-16

ISO/FDIS 15004-2

Ophthalmic instruments – Fundamental requirements and test methods – Part 2: Light hazard protection (Revision of ISO 15004:1997)

2007-01-09

ISO/FDIS 20473 Optics and photonics – Spectral bands

2007-02-04

TC 173 Assistive products for persons with disability

ISO/FDIS 9999 Assistive products for persons with disability – Classification and terminology (Revision of ISO 9999:2002)

2007-01-30

TC 198 Sterilization of health care products

ISO/FDIS 11140-3

* Sterilization of health care products – Chemical indicators – Part 3: Class 2 indicator systems for use in the Bowie and Dick-type steam penetration test (Revision of ISO 11140-3:2000)

2007-02-14

ISO/FDIS 11140-4

* Sterilization of health care products – Chemical indicators – Part 4: Class 2 indicators as an alternative to the Bowie and Dick-type test for detection of steam penetration (Revision of ISO 11140-4:2001)

2007-02-14

ISO/FDIS 11140-5

* Sterilization of health care products – Chemical indicators – Part 5: Class 2 indicators for Bowie and Dick-type air removal tests (Revision of ISO 11140-5:2000)

2007-02-14


ISO/FDIS 14813-1

* Intelligent transport systems – Reference model architecture(s) for the ITS sector – Part 1: ITS service domains, service groups and services (Revision of ISO/TR 14813-1:1999)

2007-01-13

ISO/FDIS 17687* Transport Information and Control Systems (TICS) – General fleet management and commercial freight operations – Data dictionary and message sets for electronic identification and monitoring of hazardous materials/dangerous goods transportation

2007-01-08

ISO/FDIS 24014-1

* Public transport – Interoperable fare management system – Part 1: Architecture

2007-02-07

TC 205 Building environment design

ISO/FDIS 16484-5

* Building automation and control systems – Part 5: Data communication protocol (Revision of ISO 16484-5:2003)

2007-01-30


TC 210 Quality management and corresponding general aspects for medical devices

ISO/FDIS 14971 Medical devices – Application of risk management to medical devices (Revision of ISO 14971:2000; ISO 14971:2000/Amd 1:2003)

2007-02-07

ISO/FDIS 15223-1

Medical devices – Symbols to be used with medical device labels, labelling and information to be supplied – Part 1: General requirements

2007-02-04


ISO/FDIS 15189 Medical laboratories – Particular requirements for quality and competence (Revision of ISO 15189:2003, ISO 15189:2003/DAmd 1)

2007-02-07

TC 213 Dimensional and geometrical product specifications and verification

ISO/FDIS 8062-1

Geometrical product specifications (GPS) – Dimensional and geometrical tolerances for moulded parts – Part 1: Vocabulary (Revision of ISO 8062:1994)

2007-01-02

ISO/FDIS 8062-3

Geometrical product specifications (GPS) – Dimensional and geometrical tolerances for moulded parts – Part 3: General dimensional and geometrical tolerances and machining allowances for castings (Revision of ISO 8062:1994)

2007-01-02


ISO/FDIS 2424.2

Textile floor coverings – Vocabulary (Revision of ISO 2424:1992)

2007-01-07

TC 228 Tourism and related services

ISO/FDIS 24801-1

Recreational diving services – Safety related minimum requirements for the training of recreational scuba divers – Part 1: Level 1 – Supervised diver

2007-01-03

ISO/FDIS 24801-2

Recreational diving services – Safety related minimum requirements for the training of recreational scuba divers – Part 2: Level 2 – Autonomous diver

2007-01-03

ISO/FDIS 24801-3

Recreational diving services – Safety related minimum requirements for the training of recreational scuba divers – Part 3: Level 3 – Dive leader

2007-01-03

ISO/FDIS 24802-1

Recreational diving services – Safety related minimum requirements for the training of scuba instructors – Part 1: Level 1

2007-01-03

ISO/FDIS 24802-2

Recreational diving services – Safety related minimum requirements for the training of scuba instructors – Part 2: Level 2

2007-01-03

ISO/FDIS 24803 Recreational diving services – Requirements for recreational scuba diving service providers

2007-01-03


ISO/IEC FDIS 7816-13

* Identification cards – Integrated circuit cards – Part 13: Commands for application management in a multi-application environment

2007-02-06

ISO/IEC 8652:1995/FDAmd 1

* Information technology – Programming languages – Ada – Amendment 1

2007-01-17

ISO/IEC 13818-1/FDAmd 1

* Information technology – Generic coding of moving pictures and associated audio information: Systems – Part 1: – Amendment 1: Transport of MPEG-4 streaming text and MPEG-4 lossless audio over MPEG-2 systems

2007-01-30

ISO/IEC 14496-11:2005/FDAmd 5

* Information technology – Coding of audio-visual objects – Part 11: Scene description and application engine – Amendment 5: Support for Symbolic Music Notation

2007-02-15


* Information technology – Coding of audio-visual objects – Part 22: Open Font Format

2007-02-06

ISO/IEC 14496-3:2005/FDAmd 1

* Information technology – Coding of audio-visual objects – Part 3: Audio – Amendment 1: Low delay AAC profile

2007-01-29

ISO/IEC 14496-4:2004/FDAmd 12

* Information technology – Coding of audio-visual objects – Part 4: Conformance testing – Amendment 12: Morphing & Textures conformance

2007-02-15

ISO/IEC 14496-5:2001/FDAmd 9

* Information technology – Coding of audio-visual objects – Part 5: Reference software – Amendment 9: Morphing & Textures reference software

2007-02-15

ISO/IEC 14496-5:2001/FDAmd 10

* Information technology – Coding of audio-visual objects – Part 5: Reference software – Amendment 10: SSC, DST, ALS and SLS reference software

2006-12-31


* Information technology – Radio frequency identification for item management – Part 7: Parameters for active air interface communications at 433 MHz (Revision of ISO/IEC 18000-7:2004)

2007-01-22

ISO/IEC 19776-1:2005/FDAmd 1

* Information technology – Computer graphics, image processing and environmental data representation – Extensible 3D (X3D) encodings – Part 1: Extensible Markup Language (XML) encoding – Amendment 1

2007-01-10

ISO/IEC FDIS 19799

* Information technology – Method of measuring gloss uniformity on printed pages

2007-02-07


* Information technology – MPEG audio technologies – Part 1: MPEG Surround

2007-01-13


Standards published

New International Standards published between 26 October and 14December 2006


** French version of standard previously published in English only


* Information technology – Conformance testing for the biometric application programming interface (BioAPI) – Part 1: Methods and procedures

2006-12-31


* Information technology – Conformance testing for the biometric application programming interface (BioAPI) – Part 2: Test assertions for biometric service providers

2006-12-31

ISO/IEC FDIS 27006

* Information technology – Security techniques – Requirements for bodies providing audit and certification of information security management systems

2007-01-10

Pricegroup

VAMAS Versailles Project on Advanced Materials and Standards

ISO/TTA 5:2006 * Code of practice for creep/fatigue testing of cracked components

W

ISO/CIE 28077:2006

* Photocarcinogenesis action spectrum (non-melanoma skin cancers)

D

TC 2 Fasteners

ISO 15071:1999/Cor 1:2006

Hexagon bolts with flange – Small series – Product grade A – Technical Corrigendum 1

free

ISO 15072:1999/Cor 1:2006

Hexagon bolts with flange with metric fine pitch thread – Small series – Product grade A – Technical Corrigendum 1

free


ISO 4568:2006 * Shipbuilding – Sea-going vessels – Windlasses and anchor capstans

E

ISO 22472:2006 * Ships and marine technology – Guidelines for the operation and installation of voyage data recorders (VDR)

U

TC 17 Steel

ISO 16172:2006 * Continuous hot-dip metallic-coated steel sheet for corrugated steel pipe

E

TC 20 Aircraft and space vehicles

ISO 8913:2006 * Aerospace – Lightweight polytetrafluoroethylene (PTFE) hose assemblies, classification 400 degrees F/3 000 psi (204 degrees C/20 684 kPa) and 204 degrees C/21 000 kPa (400 degrees F/3 046 psi) – Procurement specification

N

ISO 11076:2006 * Aircraft – Ground-based de-icing/anti-icing methods with fluids

P

ISO 17775:2006 * Aircraft – Ground-service connections – Potable water, toilet-flush water and toilet drain

B

ISO 21849:2006 * Aircraft and space – Industrial data – Product identification and traceability

U

TC 21 Equipment for fire protection and fire fighting

ISO 21927-2:2006

* Smoke and heat control systems – Part 2: Specification for natural smoke and heat exhaust ventilators

R

ISO 21927-3:2006

* Smoke and heat control systems – Part 3: Specification for powered smoke and heat exhaust ventilators

N

TC 22 Road vehicles

ISO 3842:2006 * Road vehicles – Fifth wheels – Interchangeability

D

ISO 9816:2006 Passenger cars – Power-off reaction of a vehicle in a turn – Open-loop test method

L

ISO/PAS 11154:2006

Road vehicles – Roof load carriers X

ISO 11898-3:2006/Cor 1:2006

Road vehicles – Controller area network (CAN) – Part 3: Low-speed, fault-tolerant, medium-dependent interface – Technical Corrigendum 1

free

ISO 13674-2:2006

Road vehicles – Test method for the quantification of on-centre handling – Part 2: Transition test

E

ISO 14229:2006 * Road vehicles – Unified diagnostic services (UDS) – Specification and requirements

XG

ISO 14572:2006 Road vehicles – Round, screened and unscreened 60 V and 600 V multi-core sheathed cables – Test methods and requirements for basic and high-performance cables

J

ISO 16234:2006 * Heavy commercial vehicles and buses – Straight-ahead braking on surfaces with split coefficient of friction – Open-loop test method

H

ISO 19812:2006 Road vehicles – M10 x 1 compact spark-plugs with flat seating and 16 mm hexagon and their cylinder head housings

D

ISO 22896:2006 * Road vehicles – Deployment and sensor bus for occupant safety systems

U

ISO 23273-3:2006

* Fuel cell road vehicles – Safety specifications – Part 3: Protection of persons against electric shock

F


ISO 3463:2006 Tractors for agriculture and forestry – Roll-over protective structures (ROPS) – Dynamic test method and acceptance conditions

P

ISO 5700:2006 Tractors for agriculture and forestry – Roll-over protective structures (ROPS) – Static test method and acceptance conditions

N


ISO 9635-1:2006

* Agricultural irrigation equipment – Irrigation valves – Part 1: General requirements

M

ISO 9635-2:2006

* Agricultural irrigation equipment – Irrigation valves – Part 2: Isolating valves

H

ISO 9635-3:2006

* Agricultural irrigation equipment – Irrigation valves – Part 3: Check valves

D

ISO 9635-4:2006

* Agricultural irrigation equipment – Irrigation valves – Part 4: Air valves

F

ISO 9635-5:2006

* Agricultural irrigation equipment – Irrigation valves – Part 5: Control valves

F

ISO 9911:2006 * Agricultural irrigation equipment – Manually operated small plastics valves

F

TC 24 Sieves, sieving and other sizing methods

ISO 15901-2:2006

* Pore size distribution and porosity of solid materials by mercury porosimetry and gas adsorption – Part 2: Analysis of mesopores and macropores by gas adsorption

P

TC 27 Solid mineral fuels

ISO 1017:2006 * Brown coals and lignites – Determination of acetone-soluble material ("resinous substance") in the benzene-soluble extract

B

TC 29 Small tools

ISO 839-1:2006 Milling machine arbors with 7/24 tapers – Part 1: Dimensions and designation

C

ISO 2780:2006 Milling cutters with tenon drive – Interchangeability dimensions for cutter arbors – Metric series

C

TC 33 Refractories

ISO 21078-2:2006

* Determination of boron(III) oxide in refractory products – Part 2: Acid extraction method for the determination of boron(III) oxide in binder components

E

TC 34 Food products

ISO 1739:2006 Butter – Determination of the refractive index of the fat (Reference method)

B

ISO 3889:2006 Milk and milk products – Specification of Mojonnier-type fat extraction flasks

C

ISO 8587:2006**

Sensory analysis – Methodology – Ranking L

ISO 12082:2006 Processed cheese and processed cheese products – Calculation of the content of added citrate emulsifying agents and acidifiers/pH-controlling agents, expressed as citric acid

A

ISO 16472:2006**

Animal feeding stuffs – Determination of amylase-treated neutral detergent fibre content (aNDF)

H

ISO 21415-2:2006

Wheat and wheat flour – Gluten content – Part 2: Determination of wet gluten by mechanical means

F

ISO 21570:2005/Cor 1:2006

Foodstuffs – Methods of analysis for the detection of genetically modified organisms and derived products – Quantitative nucleic acid based methods – Technical Corrigendum 1

free

ISO 23275-1:2006

Animal and vegetable fats and oils – Cocoa butter equivalents in cocoa butter and plain chocolate – Part 1: Determination of the presence of cocoa butter equivalents

F

ISO/TS 26844:2006

Milk and milk products – Determination of antimicrobial residues – Tube diffusion test

G


ISO 1520:2006 Paints and varnishes – Cupping test C

ISO 1522:2006 Paints and varnishes – Pendulum damping test

E

ISO 6504-3:2006**

Paints and varnishes – Determination of hiding power – Part 3: Determination of contrast ratio of light-coloured paints at a fixed spreading rate

D

ISO 11890-2:2006

Paints and varnishes – Determination of volatile organic compound (VOC) content – Part 2: Gas-chromatographic method

H

ISO 19334:2006 * Binders for paints and varnishes – Gum rosin – Gas-chromatographic analysis

D

TC 38 Textiles

ISO 1805:2006 Fishing nets – Determination of breaking force and knot breaking force of netting yarns

C

TC 39 Machine tools

ISO 230-7:2006 Test code for machine tools – Part 7: Geometric accuracy of axes of rotation

V

ISO 13041-5:2006

Test conditions for numerically controlled turning machines and turning centres – Part 5: Accuracy of feeds, speeds and interpolations

E

TC 41 Pulleys and belts (including veebelts)

ISO 252-1:1999/Cor 1:2006

Textile conveyor belts – Adhesive strength between constitutive elements – Part 1: Methods of test – Technical Corrigendum 1

free

ISO 283-1:2000/Cor 1:2006

Textile conveyor belts – Full thickness tensile testing – Part 1: Determination of tensile strength, elongation at break and elongation at the reference load – Technical Corrigendum 1

free

ISO 583-1:1999/Cor 1:2006

Conveyor belts with a textile carcass – Total thickness and thickness of elements – Part 1: Methods of test – Technical Corrigendum 1

free

ISO 703-1:1999/Cor 1:2006

Conveyor belts – Transverse flexibility and troughability – Part 1: Test method – Technical Corrigendum 1

free

ISO 14890:2003/Cor 1:2006

Conveyor belts – Specification for rubber or plastics covered conveyor belts of textile construction for general use – Technical Corrigendum 1

free

TC 42 Photography

ISO 17321-1:2006

* Graphic technology and photography – Colour characterisation of digital still cameras (DSCs) – Part 1: Stimuli, metrology and test procedures

M


ISO 18909:2006/Cor 1:2006

* Photography – Processed photographic colour films and paper prints – Methods for measuring image stability – Technical Corrigendum 1

free

TC 43 Acoustics

ISO 140-18:2006

Acoustics – Measurement of sound insulation in buildings and of building elements – Part 18: Laboratory measurement of sound generated by rainfall on building elements

H

ISO 389-5:2006 * Acoustics – Reference zero for the calibration of audiometric equipment – Part 5: Reference equivalent threshold sound pressure levels for pure tones in the frequency range 8 kHz to 16 kHz

C


ISO 18274:2004/Cor 2:2006

Welding consumables – Wire and strip electrodes, wires and rods for fusion welding of nickel and nickel alloys – Classification – Technical Corrigendum 2

free


ISO 2321:2006 * Rubber threads – Methods of test M

TC 46 Information and documentation

ISO 3166-1:2006

Codes for the representation of names of countries and their subdivisions – Part 1: Country codes

V

TC 61 Plastics

ISO 180:2000/Amd 1:2006

Plastics – Determination of Izod impact strength – Amendment 1

XZ

ISO 845:2006 * Cellular plastics and rubbers – Determination of apparent density

B

ISO 871:2006 * Plastics – Determination of ignition temperature using a hot-air furnace

D

ISO 1269:2006 Plastics – Homopolymer and copolymer resins of vinyl chloride – Determination of volatile matter (including water)

B

ISO 1874-2:2006

Plastics – Polyamide (PA) moulding and extrusion materials – Part 2: Preparation of test specimens and determination of properties

D

ISO 5659-2:2006

Plastics – Smoke generation – Part 2: Determination of optical density by a single-chamber test

R

ISO 8510-2:2006

* Adhesives – Peel test for a flexible-bonded-to-rigid test specimen assembly – Part 2: 180 degree peel

C

ISO 8873-1:2006

* Rigid cellular plastics – Spray-applied polyurethane foam for thermal insulation – Part 1: Material specifications

E

ISO 17087:2006 * Specifications for adhesives used for finger joints in non-structural lumber products

L


ISO 13503-2:2006

* Petroleum and natural gas industries – Completion fluids and materials – Part 2: Measurement of properties of proppants used in hydraulic fracturing and gravel-packing operations

N

ISO 13705:2006 * Petroleum, petrochemical and natural gas industries – Fired heaters for general refinery service

XF

ISO 14224:2006 * Petroleum, petrochemical and natural gas industries – Collection and exchange of reliability and maintenance data for equipment

XC

ISO 15156-1:2001/Cor 1:2005**

Petroleum and natural gas industries – Materials for use in H2S-containing environments in oil and gas production – Part 1: General principles for selection of cracking-resistant materials – Technical Corrigendum 1

free

ISO 19903:2006 * Petroleum and natural gas industries – Fixed concrete offshore structures

XA

ISO/TS 24817:2006

* Petroleum, petrochemical and natural gas industries – Composite repairs for pipework – Qualification and design, installation, testing and inspection

V

TC 68 Financial services

ISO 19092-1:2006

* Financial services – Biometrics – Part 1: Security framework

X

TC 72 Textile machinery and accessories

ISO 21485:2006 * Textile machinery – Draw frame for cotton spinning – Vocabulary and principles of construction

E

TC 92 Fire safety

ISO 3008:2006 * Fire resistance tests – Door and shutter assemblies

T

ISO 5658-2:2006**

Reaction to fire tests – Spread of flame – Part 2: Lateral spread on building and transport products in vertical configuration

Q

ISO 16735:2006 * Fire safety engineering – Requirements governing algebraic equations – Smoke layers

M


ISO 5418-1:2006

* Iron ores – Determination of copper – Part 1: 2,2'-Biquinolyl spectrophotometric method

F

ISO 5418-2:2006

* Iron ores – Determination of copper – Part 2: Flame atomic absorption spectrometric method

F

ISO 9682-2:2006

* Iron ores – Determination of manganese content – Part 2: Periodate spectrophotometric method

G

ISO 9683-1:2006

* Iron ores – Determination of vanadium – Part 1: BPHA spectrophotometric method

F

ISO 11534:2006 * Iron ores – Determination of tin – Flame atomic absorption spectrometric method

F

ISO 11535:2006 * Iron ores – Determination of various elements – Inductively coupled plasma atomic emission spectrometric method

M

TC 106 Dentistry

ISO 22674:2006 Dentistry – Metallic materials for fixed and removable restorations and appliances

L

TC 107 Metallic and other inorganic coatings

ISO 22778:2006 Metallic coatings – Physical vapour-deposited coatings of cadmium on iron and steel – Specification and test methods

H


ISO 22779:2006 Metallic coatings – Physical vapour-deposited coatings of aluminium – Specification and test methods

H


ISO 10813-1:2004/Cor 1:2006

* Vibration generating machines – Guidance for selection – Part 1: Equipment for environmental testing – Technical Corrigendum 1

free

TC 117 Industrial fans

ISO 13347-3:2004/Cor 1:2006

Industrial fans – Determination of fan sound power levels under standardized laboratory conditions – Part 3: Enveloping surface methods – Technical Corrigendum 1

free

ISO 13347-4:2004/Cor 1:2006

Industrial fans – Determination of fan sound power levels under standardized laboratory conditions – Part 4: Sound intensity method – Technical Corrigendum 1

free


ISO 3369:2006 * Impermeable sintered metal materials and hardmetals – Determination of density

B


IEC 60601-1-8:2006

Medical electrical equipment – Part 1-8: General requirements for basic safety and essential performance – Collateral standard: General requirements, tests and guidance for alarm systems in medical electrical equipment and medical electrical systems

XC


ISO 5006:2006 Earth-moving machinery – Operator's field of view – Test method and performance criteria

L

ISO 10532:1995/Amd 1:2004/Cor 1:2006**

Earth-moving machinery – Machine-mounted retrieval device – Performance requirements – Amendment 1 – Technical Corrigendum 1

free


ISO 2846-1:2006

* Graphic technology – Colour and transparency of printing ink sets for four-colour printing – Part 1: Sheet-fed and heat-set web offset lithographic printing

H

ISO 12642-2:2006

* Graphic technology – Input data for characterization of 4-colour process printing – Part 2: Expanded data set

N

TC 131 Fluid power systems

ISO 3019-2:2001/Cor 1:2006

* Hydraulic fluid power – Dimensions and identification code for mounting flanges and shaft ends of displacement pumps and motors – Part 2: Metric series – Technical Corrigendum 1

free

TC 135 Non-destructive testing

ISO 9712:2005/Cor 1:2006

* Non-destructive testing – Qualification and certification of personnel – Technical Corrigendum 1

free


ISO/TR 18124:2006

* Plastics piping systems – Multilayer M (metal) pipes – Test method for strength of the weld line in the metal layer and bonding between layers by use of a cone

C

TC 146 Air quality

ISO 9096:2003/Cor 1:2006

Stationary source emissions – Manual determination of mass concentration of particulate matter – Technical Corrigendum 1

free


ISO 5667-1:2006

Water quality – Sampling – Part 1: Guidance on the design of sampling programmes and sampling techniques

P

ISO 15553:2006 * Water quality – Isolation and identification of Cryptosporidium oocysts and Giardia cysts from water

R

ISO 21427-2:2006

* Water quality – Evaluation of genotoxicity by measurement of the induction of micronuclei – Part 2: Mixed population method using the cell line V79

K

ISO 22032:2006 Water quality – Determination of selected polybrominated diphenyl ethers in sediment and sewage sludge – Method using extraction and gas chromatography/mass spectrometry

M

TC 159 Ergonomics

ISO 14505-2:2006

Ergonomics of the thermal environment – Evaluation of thermal environments in vehicles – Part 2: Determination of equivalent temperature

M

ISO 15535:2006 General requirements for establishing anthropometric databases

K

TC 164 Mechanical testing of metals

ISO 7500-2:2006

Metallic materials – Verification of static uniaxial testing machines – Part 2: Tension creep testing machines – Verification of the applied force

J


ISO 11962:2002/Cor 1:2006

* Micrographics – Image mark (blip) used with 16 mm and 35 mm roll microfilm – Technical Corrigendum 1

free


ISO 24013:2006 Optics and photonics – Lasers and laser-related equipment – Measurement of phase retardation of optical components for polarized laser radiation

H


ISO 10535:2006 Hoists for the transfer of disabled persons – Requirements and test methods

U

ISO 24214:2006 * Skin barrier for ostomy aids – Vocabulary B

TC 184 Industrial automation systems and integration

ISO/TS 10303-1001:2006

* Industrial automation systems and integration – Product data representation and exchange – Part 1001: Application module: Appearance assignment

R

ISO/TS 10303-1002:2006

* Industrial automation systems and integration – Product data representation and exchange – Part 1002: Application module: Colour

S


ISO/TS 10303-1003:2006

* Industrial automation systems and integration – Product data representation and exchange – Part 1003: Application module: Curve appearance

R

ISO/TS 10303-1004:2006

* Industrial automation systems and integration – Product data representation and exchange – Part 1004: Application module: Elemental geometric shape

S

ISO/TS 10303-1006:2006

* Industrial automation systems and integration – Product data representation and exchange – Part 1006: Application module: Foundation representation

R

ISO/TS 10303-1019:2006

* Industrial automation systems and integration – Product data representation and exchange – Part 1019: Application module: Product view definition

R

ISO/TS 10303-1020:2006

* Industrial automation systems and integration – Product data representation and exchange – Part 1020: Application module: Product version relationship

R

ISO/TS 10303-1027:2006

* Industrial automation systems and integration – Product data representation and exchange – Part 1027: Application module: Contextual shape positioning

R

ISO/TS 10303-1030:2006

* Industrial automation systems and integration – Product data representation and exchange – Part 1030: Application module: Property assignment

R

ISO/TS 10303-1032:2006

* Industrial automation systems and integration – Product data representation and exchange – Part 1032: Application module: Shape property assignment

R

ISO/TS 10303-1038:2006

* Industrial automation systems and integration – Product data representation and exchange – Part 1038: Application module: Independent property representation

R

ISO/TS 10303-1046:2006

* Industrial automation systems and integration – Product data representation and exchange – Part 1046: Application module: Product replacement

R

ISO/TS 10303-1050:2006

* Industrial automation systems and integration – Product data representation and exchange – Part 1050: Application module: Dimension tolerance

S

ISO/TS 10303-1051:2006

* Industrial automation systems and integration – Product data representation and exchange – Part 1051: Application module: Geometric tolerance

J

ISO/TS 10303-1061:2006

* Industrial automation systems and integration – Product data representation and exchange – Part 1061: Application module: Project

F

ISO/TS 10303-1063:2006

* Industrial automation systems and integration – Product data representation and exchange – Part 1063: Application module: Product occurrence

R

ISO/TS 10303-1106:2006

* Industrial automation systems and integration – Product data representation and exchange – Part 1106: Application module: Extended measure representation

S

ISO/TS 10303-1111:2006

* Industrial automation systems and integration – Product data representation and exchange – Part 1111: Application module: Classification with attributes

S

ISO/TS 10303-1113:2006

* Industrial automation systems and integration – Product data representation and exchange – Part 1113: Application module: Group

R

ISO/TS 10303-1116:2006

* Industrial automation systems and integration – Product data representation and exchange – Part 1116: Application module: Pdm material aspects

R

ISO 10303-112:2006

* Industrial automation systems and integration – Product data representation and exchange – Part 112: Integrated application resource: Modelling commands for the exchange of procedurally represented 2D CAD models

W

ISO/TS 10303-1126:2006

* Industrial automation systems and integration – Product data representation and exchange – Part 1126: Application module: Document properties

R

ISO/TS 10303-1130:2006

* Industrial automation systems and integration – Product data representation and exchange – Part 1130: Application module: Derived shape element

R

ISO/TS 10303-1131:2006

* Industrial automation systems and integration – Product data representation and exchange – Part 1131: Application module: Construction geometry

R

ISO/TS 10303-1136:2006

* Industrial automation systems and integration – Product data representation and exchange – Part 1136: Application module: Text appearance

R

ISO/TS 10303-1141:2006

* Industrial automation systems and integration – Product data representation and exchange – Part 1141: Application module: Requirement view definition

R

ISO/TS 10303-1288:2006

* Industrial automation systems and integration – Product data representation and exchange – Part 1288: Application module: Management resource information

S

ISO/TS 10303-1291:2006

* Industrial automation systems and integration – Product data representation and exchange – Part 1291: Application module: Plib class reference

R

ISO/TS 10303-1345:2006

* Industrial automation systems and integration – Product data representation and exchange – Part 1345: Application module: Item definition structure

R

ISO/TS 10303-1351:2006

* Industrial automation systems and integration – Product data representation and exchange – Part 1351: Application module: Catalog data information

X

ISO/TS 10303-1352:2006

* Industrial automation systems and integration – Product data representation and exchange – Part 1352: Application module: Catalog data information and shape representation

W

ISO/TS 10303-1353:2006

* Industrial automation systems and integration – Product data representation and exchange – Part 1353: Application module: Parameterized catalog data information

W

ISO/TS 10303-1354:2006

* Industrial automation systems and integration – Product data representation and exchange – Part 1354: Application module: Furniture interior decoration

W


ISO/TS 10303-1355:2006

* Industrial automation systems and integration – Product data representation and exchange – Part 1355: Application module: Parameterized catalog data and shape representation

W

ISO/TS 10303-1366:2006

* Industrial automation systems and integration – Product data representation and exchange – Part 1366: Application module: Tagged text representation

R

ISO/TS 10303-1601:2006

* Industrial automation systems and integration – Product data representation and exchange – Part 1601: Application module: Altered package

R

ISO/TS 10303-1602:2006

* Industrial automation systems and integration – Product data representation and exchange – Part 1602: Application module: Altered part

R

ISO/TS 10303-1603:2006

* Industrial automation systems and integration – Product data representation and exchange – Part 1603: Application module: Analytical model

S

ISO/TS 10303-1604:2006

* Industrial automation systems and integration – Product data representation and exchange – Part 1604: Application module: AP210 assembly functional interface requirements

W

ISO/TS 10303-1605:2006

* Industrial automation systems and integration – Product data representation and exchange – Part 1605: Application module: AP210 assembly functional requirements

X

ISO/TS 10303-1606:2006

* Industrial automation systems and integration – Product data representation and exchange – Part 1606: Application module: AP210 assembly physical design

XA

ISO/TS 10303-1607:2006

* Industrial automation systems and integration – Product data representation and exchange – Part 1607: Application module: AP210 assembly physical interface requirements

free

ISO/TS 10303-1608:2006

* Industrial automation systems and integration – Product data representation and exchange – Part 1608: Application module: AP210 assembly physical requirements

W

ISO/TS 10303-1609:2006

* Industrial automation systems and integration – Product data representation and exchange – Part 1609: Application module: AP210 assembly requirement allocation

X

ISO/TS 10303-1610:2006

* Industrial automation systems and integration – Product data representation and exchange – Part 1610: Application module: AP210 assembly technology constraints

U

ISO/TS 10303-1611:2006

* Industrial automation systems and integration – Product data representation and exchange – Part 1611: Application module: AP210 connection zone based model extraction

V

ISO/TS 10303-1612:2006

* Industrial automation systems and integration – Product data representation and exchange – Part 1612: Application module: AP210 device functional and physical characterization

W

ISO/TS 10303-1613:2006

* Industrial automation systems and integration – Product data representation and exchange – Part 1613: Module d'application: Physical unit non planar design view

R

ISO/TS 10303-1614:2006

* Industrial automation systems and integration – Product data representation and exchange – Part 1614: Application module: AP210 functional decomposition

V

ISO/TS 10303-1615:2006

* Industrial automation systems and integration – Product data representation and exchange – Part 1615: Application module: AP210 functional requirement allocation

V

ISO/TS 10303-1616:2006

* Industrial automation systems and integration – Product data representation and exchange – Part 1616: Application module: AP210 functional specification

V

ISO/TS 10303-1617:2006

* Industrial automation systems and integration – Product data representation and exchange – Part 1617: Application module: AP210 interconnect design

X

ISO/TS 10303-1618:2006

* Industrial automation systems and integration – Product data representation and exchange – Part 1618: Application module: AP210 interconnect design for microwave

XA

ISO/TS 10303-1619:2006

* Industrial automation systems and integration – Product data representation and exchange – Part 1619: Application module: AP210 interconnect functional requirements

XA

ISO/TS 10303-1620:2006

* Industrial automation systems and integration – Product data representation and exchange – Part 1620: Application module: AP210 interconnect physical requirements

XA

ISO/TS 10303-1621:2006

* Industrial automation systems and integration – Product data representation and exchange – Part 1621: Application module: AP210 interconnect requirement allocation

XA

ISO/TS 10303-1622:2006

* Industrial automation systems and integration – Product data representation and exchange – Part 1622: Application module: AP210 interconnect technology constraints

W

ISO/TS 10303-1623:2006

* Industrial automation systems and integration – Product data representation and exchange – Part 1623: Application module: AP210 laminate assembly design

X

ISO/TS 10303-1624:2006

* Industrial automation systems and integration – Product data representation and exchange – Part 1624: Application module: AP210 package functional and physical characterization

W

ISO/TS 10303-1625:2006

* Industrial automation systems and integration – Product data representation and exchange – Part 1625: Application module: AP210 packaged part white box model

W

ISO/TS 10303-1626:2006

* Industrial automation systems and integration – Product data representation and exchange – Part 1626: Application module: AP210 physical unit physical characterization

V


ISO/TS 10303-1627:2006

* Industrial automation systems and integration – Product data representation and exchange – Part 1627: Application module: AP210 printed part functional and physical characterization

X

ISO/TS 10303-1628:2006

* Industrial automation systems and integration – Product data representation and exchange – Part 1628: Application module: Design product data management

T

ISO/TS 10303-1630:2006

* Industrial automation systems and integration – Product data representation and exchange – Part 1630: Application module: AP210 product rule

U

ISO/TS 10303-1631:2006

* Industrial automation systems and integration – Product data representation and exchange – Part 1631: Application module: Area 2D

R

ISO/TS 10303-1632:2006

* Industrial automation systems and integration – Product data representation and exchange – Part 1632: Application module: Assembly 2D shape

R

ISO/TS 10303-1633:2006

* Industrial automation systems and integration – Product data representation and exchange – Part 1633: Application module: Assembly 3D shape

R

ISO/TS 10303-1634:2006

* Industrial automation systems and integration – Product data representation and exchange – Part 1634: Application module: Assembly component placement requirements

S

ISO/TS 10303-1635:2006

* Industrial automation systems and integration – Product data representation and exchange – Part 1635: Application module: Assembly functional interface requirement

R

ISO/TS 10303-1636:2006

* Industrial automation systems and integration – Product data representation and exchange – Part 1636: Application module: Assembly module design

S

ISO/TS 10303-1637:2006

* Industrial automation systems and integration – Product data representation and exchange – Part 1637: Application module: Assembly module macro definition

R

ISO/TS 10303-1638:2006

* Industrial automation systems and integration – Product data representation and exchange – Part 1638: Application module: Assembly module with cable component 2D

R

ISO/TS 10303-1639:2006

* Industrial automation systems and integration – Product data representation and exchange – Part 1639: Application module: Assembly module with cable component 3D

R

ISO/TS 10303-1640:2006

* Industrial automation systems and integration – Product data representation and exchange – Part 1640: Application module: Assembly module with macro component

R

ISO/TS 10303-1641:2006

* Industrial automation systems and integration – Product data representation and exchange – Part 1641: Application module: Assembly module with subassembly

R

ISO/TS 10303-1642:2006

* Industrial automation systems and integration – Product data representation and exchange – Part 1642: Application module: Assembly module usage view

R

ISO/TS 10303-1643:2006

* Industrial automation systems and integration – Product data representation and exchange – Part 1643: Application module: Assembly module with interconnect component

R

ISO/TS 10303-1644:2006

* Industrial automation systems and integration – Product data representation and exchange – Part 1644: Application module: Assembly module with cable component

R

ISO/TS 10303-1645:2006

* Industrial automation systems and integration – Product data representation and exchange – Part 1645: Application module: Assembly module with packaged connector component

R

ISO/TS 10303-1646:2006

* Industrial automation systems and integration – Product data representation and exchange – Part 1646: Application module: Footprint definition

S

ISO/TS 10303-1647:2006

* Industrial automation systems and integration – Product data representation and exchange – Part 1647: Application module: Assembly physical interface requirement

S

ISO/TS 10303-1648:2006

* Industrial automation systems and integration – Product data representation and exchange – Part 1648: Application module: Assembly physical requirement allocation

R

ISO/TS 10303-1649:2006

* Industrial automation systems and integration – Product data representation and exchange – Part 1649: Application module: Assembly technology

S

ISO/TS 10303-1650:2006

* Industrial automation systems and integration – Product data representation and exchange – Part 1650: Application module: Bare die

S

ISO/TS 10303-1651:2006

* Industrial automation systems and integration – Product data representation and exchange – Part 1651: Application module: Basic curve

R

ISO/TS 10303-1652:2006

* Industrial automation systems and integration – Product data representation and exchange – Part 1652: Application module: Basic geometry

R

ISO/TS 10303-1653:2006

* Industrial automation systems and integration – Product data representation and exchange – Part 1653: Application module: Cable

R

ISO/TS 10303-1654:2006

* Industrial automation systems and integration – Product data representation and exchange – Part 1654: Application module: Characteristic

S

ISO/TS 10303-1655:2006

* Industrial automation systems and integration – Product data representation and exchange – Part 1655: Application module: Chemical substance

S


ISO/TS 10303-1656:2006

* Industrial automation systems and integration – Product data representation and exchange – Part 1656: Application module: Component grouping

R

ISO/TS 10303-1657:2006

* Industrial automation systems and integration – Product data representation and exchange – Part 1657: Application module: Component feature

R

ISO/TS 10303-1658:2006

* Industrial automation systems and integration – Product data representation and exchange – Part 1658: Application module: Connectivity allocation to physical network

R

ISO/TS 10303-1659:2006

* Industrial automation systems and integration – Product data representation and exchange – Part 1659: Application module: Curve swept solid

R

ISO/TS 10303-1660:2006

* Industrial automation systems and integration – Product data representation and exchange – Part 1660: Application module: Datum difference based model

R

ISO/TS 10303-1661:2006

* Industrial automation systems and integration – Product data representation and exchange – Part 1661: Application module: Design management

R

ISO/TS 10303-1662:2006

* Industrial automation systems and integration – Product data representation and exchange – Part 1662: Application module: Design specific assignment to assembly usage view

R

ISO/TS 10303-1663:2006

* Industrial automation systems and integration – Product data representation and exchange – Part 1663: Application module: Design specific assignment to interconnect usage view

R

ISO/TS 10303-1664:2006

* Industrial automation systems and integration – Product data representation and exchange – Part 1664: Application module: Device marking

R

ISO/TS 10303-1665:2006

* Industrial automation systems and integration – Product data representation and exchange – Part 1665: Applciation module: Electrical network definition

R

ISO/TS 10303-1666:2006

* Industrial automation systems and integration – Product data representation and exchange – Part 1666: Application module: Extended geometric tolerance

U

ISO/TS 10303-1667:2006

* Industrial automation systems and integration – Product data representation and exchange – Part 1667: Application module: Extended basic geometry

R

ISO/TS 10303-1668:2006

* Industrial automation systems and integration – Product data representation and exchange – Part 1668: Application module: Fabrication joint

R

ISO/TS 10303-1669:2006

* Industrial automation systems and integration – Product data representation and exchange – Part 1669: Application module: Fabrication requirement

R

ISO/TS 10303-1671:2006

* Industrial automation systems and integration – Product data representation and exchange – Part 1671: Application module: Feature and connection zone

R

ISO/TS 10303-1672:2006

* Industrial automation systems and integration – Product data representation and exchange – Part 1672: Application module: Fill area style

R

ISO/TS 10303-1673:2006

* Industrial automation systems and integration – Product data representation and exchange – Part 1673: Application module: Edge shape feature

R

ISO/TS 10303-1674:2006

* Industrial automation systems and integration – Product data representation and exchange – Part 1674: Application module: Functional assignment to part

R

ISO/TS 10303-1675:2006

* Industrial automation systems and integration – Product data representation and exchange – Part 1675: Application module: Functional decomposition to assembly design

R

ISO/TS 10303-1676:2006

* Industrial automation systems and integration – Product data representation and exchange – Part 1676: Application module: Functional decomposition to design

S

ISO/TS 10303-1677:2006

* Industrial automation systems and integration – Product data representation and exchange – Part 1677: Application module: Functional decomposition to interconnect design

R

ISO/TS 10303-1678:2006

* Industrial automation systems and integration – Product data representation and exchange – Part 1678: Application module: Functional decomposition with nodal representation to packaged mapping

R

ISO/TS 10303-1679:2006

* Industrial automation systems and integration – Product data representation and exchange – Part 1679: Application module: Functional specification

R

ISO/TS 10303-1680:2006

* Industrial automation systems and integration – Product data representation and exchange – Part 1680: Application module: Functional unit requirement allocation

R

ISO/TS 10303-1681:2006

* Industrial automation systems and integration – Product data representation and exchange – Part 1681: Application module: Generic material aspects

R

ISO/TS 10303-1682:2006

* Industrial automation systems and integration – Product data representation and exchange – Part 1682: Application module: Interconnect 2D shape

R

ISO/TS 10303-1684:2006

* Industrial automation systems and integration – Product data representation and exchange – Part 1684: Application module: Interconnect module connection routing

S

ISO/TS 10303-1685:2006

* Industrial automation systems and integration – Product data representation and exchange – Part 1685: Application module: Interconnect module to assembly module relationship

S

ISO/TS 10303-1686:2006

* Industrial automation systems and integration – Product data representation and exchange – Part 1686: Application module: Interconnect module usage view

S


ISO/TS 10303-1687:2006

* Industrial automation systems and integration – Product data representation and exchange – Part 1687: Application module: Interconnect module with macros

R

ISO/TS 10303-1688:2006

* Industrial automation systems and integration – Product data representation and exchange – Part 1688: Application module: Interconnect non planar shape

R

ISO/TS 10303-1689:2006

* Industrial automation systems and integration – Product data representation and exchange – Part 1689: Application module: Interconnect physical requirement allocation

S

ISO/TS 10303-1690:2006

* Industrial automation systems and integration – Product data representation and exchange – Part 1690: Application module: Interconnect placement requirements

S

ISO/TS 10303-1691:2006

* Industrial automation systems and integration – Product data representation and exchange – Part 1691: Application module: Interface component

R

ISO/TS 10303-1692:2006

* Industrial automation systems and integration – Product data representation and exchange – Part 1692: Application module: Land

S

ISO/TS 10303-1693:2006

* Industrial automation systems and integration – Product data representation and exchange – Part 1693: Application module: Layered 2D shape

R

ISO/TS 10303-1694:2006

* Industrial automation systems and integration – Product data representation and exchange – Part 1694: Application module: Layered 3D shape

R

ISO/TS 10303-1695:2006

* Industrial automation systems and integration – Product data representation and exchange – Part 1695: Application module: Layered interconnect module 2D design

R

ISO/TS 10303-1696:2006

* Industrial automation systems and integration – Product data representation and exchange – Part 1696: Application module: Layered interconnect module 3D design

R

ISO/TS 10303-1698:2006

* Industrial automation systems and integration – Product data representation and exchange – Part 1698: Application module: Layered interconnect module design

V

ISO/TS 10303-1700:2006

* Industrial automation systems and integration – Product data representation and exchange – Part 1700: Application module: Layered interconnect module with printed component design

S

ISO/TS 10303-1701:2006

* Industrial automation systems and integration – Product data representation and exchange – Part 1701: Application module: Layout macro definition

R

ISO/TS 10303-1702:2006

* Industrial automation systems and integration – Product data representation and exchange – Part 1702: Application module: Manifold subsurface

R

ISO/TS 10303-1703:2006

* Industrial automation systems and integration – Product data representation and exchange – Part 1703: Application module: Model parameter

S

ISO/TS 10303-1704:2006

* Industrial automation systems and integration – Product data representation and exchange – Part 1704: Application module: Network functional design view

S

ISO/TS 10303-1705:2006

* Industrial automation systems and integration – Product data representation and exchange – Part 1705: Application module: Functional usage view

S

ISO/TS 10303-1706:2006

* Industrial automation systems and integration – Product data representation and exchange – Part 1706: Application module: Non feature shape element

R

ISO/TS 10303-1707:2006

* Industrial automation systems and integration – Product data representation and exchange – Part 1707: Application module: Package

S

ISO/TS 10303-1708:2006

* Industrial automation systems and integration – Product data representation and exchange – Part 1708: Application module: Packaged connector model

R

ISO/TS 10303-1709:2006

* Industrial automation systems and integration – Product data representation and exchange – Part 1709: Application module: Packaged part white box model

R

ISO/TS 10303-1710:2006

* Industrial automation systems and integration – Product data representation and exchange – Part 1710: Application module: Packaged part black box model

R

ISO/TS 10303-1711:2006

* Industrial automation systems and integration – Product data representation and exchange – Part 1711: Application module: Part external reference

R

ISO/TS 10303-1712:2006

* Industrial automation systems and integration – Product data representation and exchange – Part 1712: Application module: Part feature function

R

ISO/TS 10303-1713:2006

* Industrial automation systems and integration – Product data representation and exchange – Part 1713: Application module: Part feature grouping

R

ISO/TS 10303-1714:2006

* Industrial automation systems and integration – Product data representation and exchange – Part 1714: Application module: Part feature location

R

ISO/TS 10303-1715:2006

* Industrial automation systems and integration – Product data representation and exchange – Part 1715: Application module: Part occurrence

R

ISO/TS 10303-1716:2006

* Industrial automation systems and integration – Product data representation and exchange – Part 1716: Application module: Part template 2D shape

S

ISO/TS 10303-1717:2006

* Industrial automation systems and integration – Product data representation and exchange – Part 1717: Application module: Part template 3D shape

R

ISO/TS 10303-1718:2006

* Industrial automation systems and integration – Product data representation and exchange – Part 1718: Application module: Part template extension

S


ISO/TS 10303-1719:2006

* Industrial automation systems and integration – Product data representation and exchange – Part 1719: Application module: Part template non planar shape

R

ISO/TS 10303-1720:2006

* Industrial automation systems and integration – Product data representation and exchange – Part 1720: Application module: Part template shape with parameters

R

ISO/TS 10303-1721:2006

* Industrial automation systems and integration – Product data representation and exchange – Part 1721: Application module: Physical component feature

R

ISO/TS 10303-1722:2006

* Industrial automation systems and integration – Product data representation and exchange – Part 1722: Application module: Physical layout template

R

ISO/TS 10303-1723:2006

* Industrial automation systems and integration – Product data representation and exchange – Part 1723: Application module: Physical node requirement to implementing component allocation

R

ISO/TS 10303-1724:2006

* Industrial automation systems and integration – Product data representation and exchange – Part 1724: Application module: Physical unit 2D design view

R

ISO/TS 10303-1725:2006

* Industrial automation systems and integration – Product data representation and exchange – Part 1725: Application module: Physical unit 3D design view

R

ISO/TS 10303-1726:2006

* Industrial automation systems and integration – Product data representation and exchange – Part 1726: Application module: Physical unit 2D shape

S

ISO/TS 10303-1727:2006

* Industrial automation systems and integration – Product data representation and exchange – Part 1727: Application module: Physical unit 3D shape

R

ISO/TS 10303-1728:2006

* Industrial automation systems and integration – Product data representation and exchange – Part 1728: Application module: Physical unit design view

S

ISO/TS 10303-1729:2006

* Industrial automation systems and integration – Product data representation and exchange – Part 1729: Application module: Physical unit interconnect definition

R

ISO/TS 10303-1730:2006

* Industrial automation systems and integration – Product data representation and exchange – Part 1730: Application module: Physical unit shape with parameters

S

ISO/TS 10303-1731:2006

* Industrial automation systems and integration – Product data representation and exchange – Part 1731: Application module: Constructive solid geometry 2D

R

ISO/TS 10303-1732:2006

* Industrial automation systems and integration – Product data representation and exchange – Part 1732: Application module: Physical unit usage view

S

ISO/TS 10303-1733:2006

* Industrial automation systems and integration – Product data representation and exchange – Part 1733: Application module: Planned characteristic

R

ISO/TS 10303-1734:2006

* Industrial automation systems and integration – Product data representation and exchange – Part 1734: Application module: Pre defined datum symbol

R

ISO/TS 10303-1735:2006

* Industrial automation systems and integration – Product data representation and exchange – Part 1735: Application module: Pre defined datum 2D symbol

R

ISO/TS 10303-1736:2006

* Industrial automation systems and integration – Product data representation and exchange – Part 1736: Application module: Pre defined datum 3D symbol

R

ISO/TS 10303-1737:2006

* Industrial automation systems and integration – Product data representation and exchange – Part 1737: Application module: Printed physical layout template

S

ISO/TS 10303-1738:2006

* Industrial automation systems and integration – Product data representation and exchange – Part 1738: Application module: Product identification extension

R

ISO/TS 10303-1739:2006

* Industrial automation systems and integration – Product data representation and exchange – Part 1739: Application module: Production rule

S

ISO/TS 10303-1740:2006

* Industrial automation systems and integration – Product data representation and exchange – Part 1740: Application module: Requirement decomposition

S

ISO/TS 10303-1741:2006

* Industrial automation systems and integration – Product data representation and exchange – Part 1741: Application module: Sequential laminate assembly design

S

ISO/TS 10303-1742:2006

* Industrial automation systems and integration – Product data representation and exchange – Part 1742: Application module: Shape composition

R

ISO/TS 10303-1743:2006

* Industrial automation systems and integration – Product data representation and exchange – Part 1743: Application module: Shape parameters

R

ISO/TS 10303-1744:2006

* Industrial automation systems and integration – Product data representation and exchange – Part 1744: Application module: Discrete shield

R

ISO/TS 10303-1745:2006

* Industrial automation systems and integration – Product data representation and exchange – Part 1745: Application module: Signal

R

ISO/TS 10303-1746:2006

* Industrial automation systems and integration – Product data representation and exchange – Part 1746: Application module: Software

R

ISO/TS 10303-1747:2006

* Industrial automation systems and integration – Product data representation and exchange – Part 1747: Application module: Specification document

S

ISO/TS 10303-1748:2006

* Industrial automation systems and integration – Product data representation and exchange – Part 1748: Application module: Stratum non planar shape

R


ISO/TS 10303-1749:2006

* Industrial automation systems and integration – Product data representation and exchange – Part 1749: Application module: Styled curve

R

ISO/TS 10303-1750:2006

* Industrial automation systems and integration – Product data representation and exchange – Part 1750: Application module: Text representation

R

ISO/TS 10303-1751:2006

* Industrial automation systems and integration – Product data representation and exchange – Part 1751: Application module: Test requirement allocation

R

ISO/TS 10303-1752:2006

* Industrial automation systems and integration – Product data representation and exchange – Part 1752: Application module: Thermal network definition

R

ISO/TS 10303-1753:2006

* Industrial automation systems and integration – Product data representation and exchange – Part 1753: Application module: Value with unit extension

S

ISO/TS 10303-1754:2006

* Industrial automation systems and integration – Product data representation and exchange – Part 1754: Application module: Via component

R

ISO/TS 10303-1755:2006

* Industrial automation systems and integration – Product data representation and exchange – Part 1755: Application module: Physical connectivity definition

S

ISO/TS 10303-1756:2006

* Industrial automation systems and integration – Product data representation and exchange – Part 1756: Application module: Conductivity material aspects

R

ISO/TS 10303-1757:2006

* Industrial automation systems and integration – Product data representation and exchange – Part 1757: Application module: Test select product

R

ISO/TS 10303-1759:2006

* Industrial automation systems and integration – Product data representation and exchange – Part 1759: Application module: AP210 datum difference based model definition

W

ISO/TS 10303-1760:2006

* Industrial automation systems and integration – Product data representation and exchange – Part 1760: Application module: Pre defined product data management specializations

S

ISO/TS 10303-1761:2006

* Industrial automation systems and integration – Product data representation and exchange – Part 1761: Application module: Information product

R

ISO/TS 10303-1762:2006

* Industrial automation systems and integration – Product data representation and exchange – Part 1762: Application module: Generic product occurence

R

ISO/TS 10303-1763:2006

* Industrial automation systems and integration – Product data representation and exchange – Part 1763: Application module: Integral shield

R

ISO/TS 10303-1764:2006

* Industrial automation systems and integration – Product data representation and exchange – Part 1764: Application module: Shape feature

R

ISO/TS 10303-1765:2006

* Industrial automation systems and integration – Product data representation and exchange – Part 1765: Application module: Characterizable object

R

ISO 10303-236:2006

* Industrial automation systems and integration – Product data representation and exchange – Part 236: Application protocol: Furniture catalog and interior design

XM

ISO/TS 10303-410:2006

* Industrial automation systems and integration – Product data representation and exchange – Part 410: Application module: AP210 electronic assembly interconnect and packaging design

XB

ISO/TS 10303-436:2006

* Industrial automation systems and integration – Product data representation and exchange – Part 436: Application module: AP236 furniture catalog and interior design

X

ISO 10303-503:2000/Cor 1:2006

* Industrial automation systems and integration – Product data representation and exchange – Part 503: Application interpreted construct: Geometrically bounded 2D wireframe – Technical Corrigendum 1

free

ISO 13584-102:2006

* Industrial automation systems and integration – Parts library – Part 102: View exchange protocol by ISO 10303 conforming specification

M

ISO 13584-511:2006

* Industrial automation systems and integration – Parts library – Part 511: Mechanical systems and components for general use – Reference dictionary for fasteners

XD

ISO 16100-4:2006

* Industrial automation systems and integration – Manufacturing software capability profiling for interoperability – Part 4: Conformance test methods, criteria and reports

P

ISO/PAS 20542:2006

* Industrial automation systems and integration – Product data representation and exchange – Reference model for systems engineering

P

TC 188 Small craft

ISO 12402-5:2006/Cor 1:2006

Personal flotation devices – Part 5: Buoyancy aids (level 50) – Safety requirements – Technical Corrigendum 1

free

ISO 12402-7:2006

Personal flotation devices – Part 7: Materials and components – Safety requirements and test methods

W

ISO 21487:2006 Small craft – Permanently installed petrol and diesel fuel tanks

D

TC 193 Natural gas

ISO 12213-1:2006

* Natural gas – Calculation of compression factor – Part 1: Introduction and guidelines

G

ISO 12213-2:2006

* Natural gas – Calculation of compression factor – Part 2: Calculation using molar-composition analysis

P

ISO 12213-3:2006

* Natural gas – Calculation of compression factor – Part 3: Calculation using physical properties

R


ISO 23874:2006 * Natural gas – Gas chromatographic requirements for hydrocarbon dewpoint calculation

M

TC 198 Sterilization of health care products

ISO 13408-5:2006

Aseptic processing of health care products – Part 5: Sterilization in place

G

ISO 15883-2:2006**

Washer-disinfectors – Part 2: Requirements and tests for washer-disinfectors employing thermal disinfection for surgical instruments, anaesthetic equipment, bowls, dishes, receivers, utensils, glassware, etc.

E

ISO 15883-3:2006**

Washer-disinfectors – Part 3: Requirements and tests for washer-disinfectors employing thermal disinfection for human waste containers

F

TC 199 Safety of machinery

ISO 13849-1:2006

Safety of machinery – Safety-related parts of control systems – Part 1: General principles for design

X

ISO 13850:2006 Safety of machinery – Emergency stop – Principles for design

C

TC 202 Microbeam analysis

ISO 22489:2006 Microbeam analysis – Electron probe microanalysis – Quantitative point analysis for bulk specimens using wavelength-dispersive X-ray spectroscopy

G

ISO 23833:2006 Microbeam analysis – Electron probe microanalysis (EPMA) – Vocabulary

U


ISO 15662:2006 * Intelligent transport systems – Wide area communication – Protocol management information

Q

TC 211 Geographic information/Geomatics

ISO/TS 19138:2006

* Geographic information – Data quality measures

V


ISO 20776-1:2006

Clinical laboratory testing and in vitro diagnostic test systems – Susceptibility testing of infectious agents and evaluation of performance of antimicrobial susceptibility test devices – Part 1: Reference method for testing the in vitro activity of antimicrobial agents against rapidly growing aerobic bacteria involved in infectious diseases

K


ISO 2692:2006 Geometrical product specifications (GPS) – Geometrical tolerancing – Maximum material requirement (MMR), least material requirement (LMR) and reciprocity requirement (RPR)

P

ISO 5436-2:2001/Cor 1:2006

Geometrical Product Specifications (GPS) – Surface texture: Profile method; Measurement standards – Part 2: Software measurement standards – Technical Corrigendum 1

free

ISO/TS 16610-1:2006

Geometrical product specifications (GPS) – Filtration – Part 1: Overview and basic concepts

L

ISO/TS 16610-20:2006

Geometrical product specifications (GPS) – Filtration – Part 20: Linear profile filters: Basic concepts

G

ISO/TS 16610-22:2006

Geometrical product specifications (GPS) – Filtration – Part 22: Linear profile filters: Spline filters

H

ISO/TS 16610-29:2006

Geometrical product specifications (GPS) – Filtration – Part 29: Linear profile filters: Spline wavelets

J

ISO/TS 16610-40:2006

Geometrical product specifications (GPS) – Filtration – Part 40: Morphological profile filters: Basic concepts

H

ISO/TS 16610-41:2006

Geometrical product specifications (GPS) – Filtration – Part 41: Morphological profile filters: Disk and horizontal line-segment filters

G

ISO/TS 16610-49:2006

Geometrical product specifications (GPS) – Filtration – Part 49: Morphological profile filters: Scale space techniques

J

TC 215 Health informatics

ISO 20301:2006 * Health informatics – Health cards – General characteristics

F

ISO 20302:2006 * Health informatics – Health cards – Numbering system and registration procedure for issuer identifiers

D

ISO 21549-4:2006

* Health informatics – Patient healthcard data – Part 4: Extended clinical data

K

TC 216 Footwear

ISO/TR 20573:2006

* Footwear – Performance requirements for components for footwear – Heels and top pieces

E

TC 217 Cosmetics

ISO 21148:2005/Cor 1:2006**

Cosmetics – Microbiology – General instructions for microbiological examination – Technical Corrigendum 1

free

TC 220 Cryogenic vessels

ISO 21012:2006 * Cryogenic vessels – Hoses G

TMB Technical Management Board

IWA 5:2006 * Emergency preparedness D

ISO/IEC Guide 75:2006

* Strategic principles for future IEC and ISO standardization in industrial automation

P


ISO/IEC 7816-3:2006

* Identification cards – Integrated circuit cards – Part 3: Cards with contacts – Electrical interface and transmission protocols

T

ISO/IEC 8802-11:2005/Amd 6:2006

* Information technology – Telecommunications and information exchange between systems – Local and metropolitan area networks – Specific requirements – Part 11: Wireless LAN Medium Access Control (MAC) and Physical Layer (PHY) specifications – Amendment 6: Medium Access Control (MAC) Security Enhancements

XC


ISO/IEC 8824-1:2002/Amd 3:2006

* Information technology – Abstract Syntax Notation One (ASN.1): Specification of basic notation – Part 1: – Amendment 3: Time type support

R

ISO/IEC 8824-1:2002**

Information technology – Abstract Syntax Notation One (ASN.1): Specification of basic notation – Part 1:

XB

ISO/IEC 8824-2:2002/Cor 1:2006

* Information technology – Abstract Syntax Notation One (ASN.1): Information object specification – Part 2: – Technical Corrigendum 1

free

ISO/IEC 8825-3:2002/Amd 2:2006

* Information technology – ASN.1 encoding rules: Specification of Encoding Control Notation (ECN) – Part 3: – Amendment 2

XZ

ISO/IEC 8825-4:2002/Amd 2:2006

* Information technology – ASN.1 encoding rules: XML Encoding Rules (XER) – Part 4: – Amendment 2: Time type support

XZ

ISO/IEC 9594-2:2005**

Information technology – Open Systems Interconnection – The Directory: Models – Part 2:

XE

ISO/IEC 9594-3:2005**

Information technology – Open Systems Interconnection – The Directory: Abstract service definition – Part 3:

X

ISO/IEC 9594-4:2005**

Information technology – Open Systems Interconnection – The Directory: Procedures for distributed operation – Part 4:

XA

ISO/IEC 9594-9:2005**

Information technology – Open Systems Interconnection – The Directory: Replication – Part 9:

Q

ISO/IEC 9973:2006

* Information technology – Computer graphics, image processing and environmental data representation – Procedures for registration of items

Q

ISO/IEC 13249-3:2006

* Information technology – Database languages – SQL multimedia and application packages – Part 3: Spatial

XL

ISO/IEC 14496-16:2006

* Information technology – Coding of audio-visual objects – Part 16: Animation Framework eXtension (AFX)

XD

ISO/IEC 14496-21:2006

* Information technology – Coding of audio-visual objects – Part 21: MPEG-J Graphics Framework eXtensions (GFX)

R

ISO/IEC 14496-5:2001/Amd 6:2005/Cor 1:2006

* Information technology – Coding of audio-visual objects – Part 5: Reference software – Amendment 6: Advanced Video Coding (AVC) and High Efficiency Advanced Audio Coding (HE AAC) reference software – Technical Corrigendum 1

free

ISO/IEC 14776-412:2006

* Information technology – Small Computer System Interface (SCSI) – Part 412: Architecture Model -2 (SAM-2)

X

ISO/IEC 14888-3:2006

* Information technology – Security techniques – Digital signatures with appendix – Part 3: Discrete logarithm based mechanisms

V

ISO/IEC 15444-9:2005/Amd 1:2006

* Information technology – JPEG 2000 image coding system: Interactivity tools, APIs and protocols – Part 9: – Amendment 1: APIs, metadata, and editing

XZ

ISO/IEC 15693-2:2006

* Identification cards – Contactless integrated circuit cards – Vicinity cards – Part 2: Air interface and initialization

G

ISO/IEC TR 15938-8:2002/Amd 2:2006

* Information technology – Multimedia content description interface – Part 8: Extraction and use of MPEG-7 descriptions – Amendment 2: Extraction and use of MPEG-7 perceptual 3D shape descriptor

XZ

ISO/IEC 16085:2006

* Systems and software engineering – Life cycle processes – Risk management

Q

ISO/IEC 17341:2006

* Information technology – Data Interchange on 120 mm and 80 mm Optical Disk using +RW Format – Capacity: 4,7 Gbytes and 1,46 Gbytes per Side (Recording speed up to 4X)

XB

ISO/IEC 17344:2006

* Information technology – Data Interchange on 120 mm and 80 mm Optical Disk using +R Format – Capacity: 4,7 and 1,46 Gbytes per Side (Recording speed up to 16X)

XC

ISO/IEC 17345:2006

* Information technology – Data Interchange on 130 mm Rewritable and Write Once Read Many Ultra Density Optical (UDO) Disk Cartridges – Capacity: 30 Gbytes per Cartridge – First Generation

XC

ISO/IEC 19798:2006

* Method for the determination of toner cartridge yield for colour printers and multi-function devices that contain printer components

J

ISO/IEC 20000-1:2005**

Information technology – Service management – Part 1: Specification

H

ISO/IEC 21000-10:2006/Amd 1:2006

* Information technology – Multimedia framework (MPEG-21) – Part 10: Digital Item Processing – Amendment 1: Additional C++ bindings

XZ

ISO/IEC 21000-6:2004/Amd 1:2006

* Information technology – Multimedia framework (MPEG-21) – Part 6: Rights Data Dictionary – Amendment 1: Digital Item Identifier relationship types

XZ

ISO/IEC 23002-1:2006

* Information technology – MPEG video technologies – Part 1: Accuracy requirements for implementation of integer-output 8x8 inverse discrete cosine transform

F

ISO/IEC 23360-1:2006

* Linux Standard Base (LSB) core specification 3.1 – Part 1: Generic specification

XK

ISO/IEC 23360-2:2006

* Linux Standard Base (LSB) core specification 3.1 – Part 2: Specification for IA32 architecture

W

ISO/IEC 23360-3:2006

* Linux Standard Base (LSB) core specification 3.1 – Part 3: Specification for IA64 architecture

X

ISO/IEC 23360-4:2006

* Linux Standard Base (LSB) core specification 3.1 – Part 4: Specification for AMD64 architecture

W

ISO/IEC 23360-5:2006

* Linux Standard Base (LSB) core specification 3.1 – Part 5: Specification for PPC32 architecture

W

ISO/IEC 23360-6:2006

* Linux Standard Base (LSB) core specification 3.1 – Part 6: Specification for PPC64 architecture

W


Standards confirmed

The following International Standards are confirmed for a five yearperiod:

ISO/IEC 23360-7:2006

* Linux Standard Base (LSB) core specification 3.1 – Part 7: Specification for S390 architecture

W

ISO/IEC 23360-8:2006

* Linux Standard Base (LSB) core specification 3.1 – Part 8: Specification for S390X architecture

W

ISO/IEC 24702:2006

* Information technology – Generic cabling – Industrial premises

W

ISO/IEC 24711:2006

* Method for the determination of ink cartridge yield for colour inkjet printers and multi-function devices that contain printer components

N

ISO/IEC 24712:2006

* Colour test pages for measurement of office equipment consumable yield

N

ISO/IEC TR 24715:2006

* Information technology – Programming languages, their environments and system software interfaces – Technical Report on the Conflicts between the ISO/IEC 9945 (POSIX) and the Linux Standard Base (ISO/IEC 23360)

L

ISO/IEC 24730-2:2006

* Information technology – Real-time locating systems (RTLS) – Part 2: 2,4 GHz air interface protocol

P

ISO/IEC 24738:2006

* Information technology – Icon symbols and functions for multimedia link attributes

K

ISO/IEC 25436:2006

* Information technology – Eiffel: Analysis, Design and Programming Language

XC

ISO/IEC 26300:2006

* Information technology – Open Document Format for Office Applications (OpenDocument) v1.0

XL

ISO/IEC TR 26905:2006

* Information technology – Telecommunications and information exchange between systems – Enterprise Communication in Next Generation Corporate Networks (NGCN) involving Public Next Generation Networks (NGN)

P

ISO/IEC 26925:2006

* Information technology – Digital storage media for information interchange – Data Interchange on 120 mm and 80 mm Optical Disk using +RW HS Format - Capacity: 4,7 and 1,46 Gbytes per Side (Recording speed 8X)

XB

ISO/IEC TR 26927:2006

* Information technology – Telecommunications and information exchange between systems – Corporate Telecommunication Networks – Mobility for Enterprise Communications

U

CIE International Commission on Illumination

ISO/CIE 17166:1999


ISO 5630-1:1991 (reconfirmed)



ISO 8787:1986 (reconfirmed)


TC 10 Technical product documentation

IEC 82045-1:2001

TC 17 Steel









TC 22 Road vehicles

ISO 6624-1:2001

ISO 6624-3:2001



ISO 7859:2000



ISO 8715:2001






ISO 11783-4:2001

TC 34 Food products


ISO 16649-1:2001

ISO 16649-2:2001

ISO 17410:2001


ISO 15741:2001

TC 38 Textiles

ISO 105-E03:1994 (reconfirmed)




TC 60 Gears


ISO 9083:2001

ISO 10300-3:2001

TC 72 Textile machinery and accessories

ISO 9902-1:2001

ISO 9902-2:2001

ISO 9902-3:2001

ISO 9902-4:2001

ISO 9902-5:2001

ISO 9902-6:2001

ISO 9902-7:2001

TC 83 Sports and recreational equipment








ISO 6289:2003/Cor 1:2005

ISO 6289:2003





ISO 7795:1994




ISO 8783:1999



ISO 10958-1:1998

ISO 10958-2:2004

ISO 11497:1998

TC 84 Devices for administration of medicinal products and intravascular catheters



TC 92 Fire safety

ISO 5658-4:2001


ISO 16063-13:2001


ISO 9360-1:2000

ISO 9360-2:2001







ISO 8795:2001




ISO 13951:2001

ISO 13953:2001

TC 150 Implants for surgery

ISO 7206-2:1996

TC 156 Corrosion of metals and alloys






ISO 11881:1999

TC 170 Surgical instruments

ISO 7741:1986


ISO 7176-11:1992

TC 184 Industrial automation systems and integration

ISO/TS 10303-1001:2004

ISO/TS 10303-1050:2005

ISO/TS 10303-1051:2005

ISO/TS 10303-1061:2004

ISO/TS 10303-1063:2005

ISO/TS 10303-1106:2004

ISO/TS 10303-1111:2005

ISO/TS 10303-1113:2004

ISO/TS 10303-1131:2005

ISO/TS 10303-1291:2004

TC 216 Footwear

ISO 18454:2001

ISO 20866:2001


Standards withdrawn


ISO 20867:2001

ISO 20868:2001

ISO 20869:2001

ISO 20870:2001

ISO 20871:2001

ISO 20872:2001

ISO 20873:2001

ISO 20874:2001

ISO 20875:2001

ISO 20876:2001

ISO 20877:2001








ISO 11378-2:2001

ISO/PAS 11856:2003

ISO/PAS 17984:2001

TC 226 Materials for the production of primary aluminium

ISO 5931:2000

ISO 8007-1:1999

ISO 8007-2:1999

ISO 9406:1995

ISO 10143:1995

ISO 10236:1995

ISO 10238:1999

ISO 11713:2000

ISO 12977:1999

ISO 12979:1999

ISO 12980:2000

ISO 12981-1:2000

ISO 12982-1:2000

ISO 12984:2000

ISO 12985-1:2000

ISO 12985-2:2000

ISO 12986-1:2000

ISO 12988-1:2000

ISO 12989-1:2000

ISO 14422:1999

TC 2 Fasteners

ISO 21269:2004

TC 22 Road vehicles

ISO 11154-1:1995 (replaced by ISO/PAS 11154:2006)

ISO 11154-4:2004 (replaced by ISO/PAS 11154:2006)


ISO 4254-2:1986

ISO 9635:1990 (replaced by ISO 9635-1:2006 & ISO 9635-2:2006 & ISO 9635-4:2006 & ISO 9635-5:2006 & ISO 9635-3:2006)

ISO 9952:1993 (replaced by ISO 9635-3:2006)


TC 29 Small tools

ISO 2352:2000

TC 34 Food products


ISO 6464:1983


TC 42 Photography

ISO 515:1973

ISO 686:1985

ISO 1229:1989

ISO 7329:1989

ISO 9767:1990

ISO 11314:1995

ISO 11315-3:1999

ISO 11316:1999

TC 94 Personal safety – Protective clothing and equipment

ISO 2251:1991





TC 106 Dentistry

ISO 1562:2004 (replaced by ISO 22674:2006)

ISO 6871-1:1994 (replaced by ISO 22674:2006)





Meeting calendar

(update at 14 December 2006)Meetings called for the month of December 2006 are not repeated inthis edition.* Information definite but meeting not yet formally convened** Provisional






ISO 9340:1996

January 2007

8-9 London (United Kingdom)

TC 44/SC 11 Welding and allied processes/Qualification requirements for welding and allied processes personnel

11 Paris (France) TC 17/SC 3 Steel/Steels for structural purposes

15-16 Paris (France) TC 44/SC 3 Welding and allied processes/Welding consumables

15-19 Orlando (USA) * TC 69/SC 4 Applications of statistical methods/Applications of statistical methods in process management

18 Braunschweig (Germany)


18-19 St. Gallen (Switzerland)

** IULTCS International Union of Leather Technologists and Chemists Societies

January-February 2007

29-2 Christchurch (New Zealand)

TC 121/SC 3 Anaesthetic and respiratory equipment/Lung ventilators and related equipment

February 2007

12-16 Bucarest (Romania)

** TC 67/EC/MC Executive committee and Management committee

13 Delft (Netherlands)

TC 158 Analysis of gases

14-15 Reading (United Kingdom)

** TC 190/SC 1 Soil quality/Evaluation of criteria, terminology and codification

19 Spain ** JTC 1/SC 35 Information technology/User interfaces

22 Korea, Republic of

TC 94/SC 13 Personal safety – Protective clothing and equipment/Protective clothing

22-23 Switzerland ** IULTCS International Union of Leather Technologists and Chemists Societies

24-26 Orlando (USA) ** TC 69/SC 1 Applications of statistical methods/Terminology and symbols

27 Helsinki (Finland) ** TC 107/SC 3 Metallic and other inorganic coatings/Electrodeposited coatings and related finishes

27 Helsinki (Finland) TC 107/SC 4 Metallic and other inorganic coatings/Hot dip coatings (galvanized, etc.)

27 Helsinki (Finland) ** TC 107/SC 7 Metallic and other inorganic coatings/Corrosion tests

** TC 190/SC 4 Soil quality/Biological methods

March 2007

1 Paris (France) TC 23/SC 2 Tractors and machinery for agriculture and forestry/Common tests

1 Helsinki (Finland) TC 107 Metallic and other inorganic coatings

8-9 Paris (France) ** TC 29/SC 8 Small tools/Tools for pressing and moulding


JTC 1/SC 36 Information technology/Information technology for learning, education and training

14 Stockholm (Sweden)


15-17 Geneva (Switzerland)

** COUNCIL Council

22-24 Oslo (Norway) JTC 1/SC 34 Information technology/Document description and processing languages

25-29 Montreal (Canada)

* TC 215 Health informatics

26-27 Venice (Italy) TC 89/SC 3 Wood-based panels/Plywood

26-30 Raleigh (USA) TC 23/SC 13 Tractors and machinery for agriculture and forestry/Powered lawn and garden equipment

26-30 Funchal (Portugal)

* TC 184/SC 4 Industrial automation systems and integration/Industrial data

26-31 Cyprus * TC 92/SC 2 Fire safety/Fire containment

27 Venice (Italy) * TC 89/SC 1 Wood-based panels/Fibre boards

27 Venice (Italy) * TC 89/SC 2 Wood-based panels/Particle boards


28-30 Washington, D.C (USA)

** TC 58/SC 4 Gas cylinders/Operational requirements for gas cylinders

29 Frankfurt (Germany)

TC 23/SC 19 Tractors and machinery for agriculture and forestry/Agricultural electronics

29 Venice (Italy) * TC 89 Wood-based panels

30-31 Nürnberg (Germany)

TC 24/SC 4 Sieves, sieving and other sizing methods/Sizing by methods other than sieving

20 Germany ** TC 118/SC 3 Compressors and pneumatic tools, machines and equipment/Pneumatic tools and machines

March-April 2007

** TC 91 Surface active agents

April 2007


** TC 58 Gas cylinders

2-4 Tokyo (Japan) TC 219 Floor coverings

2-6 Turkey ** TC 120 and SC

Leather

4 Paris (France) ** TC 34/SC 7 Food products/Spices, culinary herbs and condiments

5-6 Beijing (China) * TC 5/SC 2 Ferrous metal pipes and metallic fittings/Cast iron pipes, fittings and their joints

11-12 Stockholm (Sweden)

** TC 44/SC 10 Welding and allied processes/Unification of requirements in the field of metal welding

12-13 La Plaine St-Denis (France)

TC 110/SC 4 Industrial trucks/Variable reach rough terrain

16-20 Frankfurt (Germany)

* JTC 1/SC 2 Information technology/Coded character sets

16-20 Xian (China) ** JTC 1/SC 6 Information technology/Telecommunications and information exchange between systems

16-20 Praha (Czech Republic)

* TC 108/SC 5 Mechanical vibration and shock/Condition monitoring and diagnostics of machines

16-20 Yokohama (Japan)

* TC 178 Lifts, escalators and moving walks

19 Paris (France) ** TC 23/SC 6 Tractors and machinery for agriculture and forestry/Equipment for crop protection

22-23 Chicago (USA) TC 173/SC 3 Assistive products for persons with disability/Aids for ostomy and incontinence

23-24 Buenos Aires (Argentina)

* TC 34/SC 11 Food products/Animal and vegetable fats and oils

23-27 Egypt ** TC 34/SC 9 Food products/Microbiology

23-27 Berlin (Germany) * TC 108 Mechanical vibration and shock

23-27 Berlin (Germany) ** TC 108/SC 2 Mechanical vibration and shock/Measurement and evaluation of mechanical vibration and shock as applied to machines, vehicles and structures

23-27 Berlin (Germany) ** TC 108/SC 3 Mechanical vibration and shock/Use and calibration of vibration and shock measuring instruments

23-27 Finland ** TC 163 and SC

Thermal performance and energy use in the built environment

24 London (United Kingdom)

TC 117 Industrial fans

24-25 Doha (Qatar) ** TC 67/SC 2 Materials, equipment and offshore structures for petroleum, petrochemical and natural gas industries/Pipeline transportation systems

24-28 Bangkok (Thailand)

** TC 130 Graphic technology

25 Berlin (Germany) * TC 108/CC ISO/TC 108-ISO 9000 series coordinating committee

25 Berlin (Germany) * TC 108/SC 6 Mechanical vibration and shock/Vibration and shock generating systems

26 Madrid (Spain) TC 85/SC 2 Nuclear energy/Radiation protection

27-29 Berlin (Germany) ** TC 161 Control and protective devices for gas and oil burners and gas and oil burning appliances

April-May 2007

30-1 San José, California (USA)

** JTC 1/SC 29 Information technology/Coding of audio, picture, multimedia and hypermedia information

May 2007

1-8 Seoul (Korea, Republic of)

** TC 5/SC 10 Ferrous metal pipes and metallic fittings/Metallic flanges and their joints

7 Busan (Korea, Republic of)

** TC 104 and SC

Freight containers

7-10 Santiago de Compostela (Spain)

** TC 46 Information and documentation

7-10 Berlin (Germany) ** TC 145 and SC

Graphical symbols

7-11 ** TC 39/SC 2 Machine tools/Test conditions for metal cutting machine tools


8-9 Rio de Janeiro (Brazil)

** TC 67/SC 6 Materials, equipment and offshore structures for petroleum, petrochemical and natural gas industries/Processing equipment and systems


** TC 195/SC 1 Building construction machinery and equipment/Machinery and equipment for concrete work

8-11 Oslo (Norway) ** TC 59/SC 15 Building construction/Performance criteria for single family attached and detached dwellings

8-11 Malta * TC 92/SC 1 Fire safety/Fire initiation and growth

9-10 Tokyo (Japan) ** TC 172/SC 6 Optics and photonics/Geodetic and surveying instruments


** TC 195 Building construction machinery and equipment

14 Vienna (Austria) ** TC 85/SC 5 Nuclear energy/Nuclear fuel technology

14-17 Montreal (Canada)

** TC 192 Gas turbines

20 Orlando (USA) ** TC 10 and SCTechnical product documentation

21-25 Rio de Janeiro (Brazil)

** COPOLCO Committee on consumer policy

28-31 Matsumoto (Japan)

** JTC 1/SC 28 Information technology/Office equipment

29-30 Boston (USA) ** TC 21/SC 8 Equipment for fire protection and fire fighting/Gaseous media and firefighting systems using gas

31 Boston (USA) ** TC 21/SC 3 Equipment for fire protection and fire fighting/Fire detection and alarm systems

Sweden, Spain ** TC 46/SC 11 Information and documentation/Archives/records management

China, United Kingdom

** TC 113 and SC

Hydrometry

** TC 113/SC 2 Hydrometry/Flow measurement structures

Hamburg (Germany)

** TC 115 Pumps

Beijing (China) ** TC 212 Clinical laboratory testing and in vitro diagnostic test systems

South Africa * TC 217 Cosmetics

USA ** TC 223 Societal Security (provisional)

May-June 2007

1-1 Denmark ** TC 69 Applications of statistical methods

28-2 Beijing (China) ** TC 96 and SCCranes

29-2 Boston (USA) * TC 21 Equipment for fire protection and fire fighting

Denmark ** TC 69/SC 6 Applications of statistical methods/Measurement methods and results

31-1 Rome (Italy) ** TC 211 Geographic information/Geomatics

June 2007

1 Boston (USA) ** TC 21/SC 2 Equipment for fire protection and fire fighting/Manually transportable fire extinguishers

3-8 Rotterdam (Netherlands)

** TC 27 and SCSolid mineral fuels

4-8 Dinard (France) * TC 114 and SC

Horology

4-8 Tsukuba (Japan) ** REMCO Committee on reference materials

5-6 Calgary (Canada)

** TC 67/SC 7 Materials, equipment and offshore structures for petroleum, petrochemical and natural gas industries/Offshore structures

6-8 Bogota (Colombia)

** TC 34/SC 15 Food products/Coffee


* TC 184/SC 2 Industrial automation systems and integration/Robots and robotic devices

8 Pretoria (South Africa)

** JTC 1/SC 31 Information technology/Automatic identification and data capture techniques

11 Helsinki (Finland) ** TC 176/SC 1 Quality management and quality assurance/Concepts and terminology

11-15 San Diego (USA) * TC 121 and SC

Anaesthetic and respiratory equipment

11-15 San Diego (USA) * TC 121/SC 3 Anaesthetic and respiratory equipment/Lung ventilators and related equipment

11-15 Helsinki (Finland) ** TC 176/SC 2 Quality management and quality assurance/Quality systems

13 Beijing (China) ** TC 123/SC 6 Plain bearings/Terms and common items

14 Beijing (China) ** TC 123/SC 2 Plain bearings/Materials and lubricants, their properties, characteristics, test methods and testing conditions

14 Beijing (China) ** TC 123/SC 3 Plain bearings/Dimensions, tolerances and construction details

14-15 Berlin (Germany) ** TC 206 Fine ceramics


15 Beijing (China) ** TC 123/SC 5 Plain bearings/Quality analysis and assurance

15 ** TC 193 and SC

Natural gas

18 Stockholm (Sweden)

** TC 203 Technical energy systems

20-21 Sweden ** TC 29/SC 10 Small tools/Assembly tools for screws and nuts, pliers and nippers

21-22 Guangzhou (China)

** TC 34/SC 4 Food products/Cereals and pulses

21-22 San Francisco (USA)

** TC 67/SC 4 Materials, equipment and offshore structures for petroleum, petrochemical and natural gas industries/Drilling and production equipment

22-29 Beijing (China) ** TC 207 Environmental management

23 San Francisco (USA)

** TC 67/SC 5 Materials, equipment and offshore structures for petroleum, petrochemical and natural gas industries/Casing, tubing and drill pipe

24-29 Boston (USA) ** TC 85/SC 6 Nuclear energy/Reactor technology

25 Paris (France) ** TC 4/SC 5 Rolling bearings/Needle roller bearings


** TC 171 and SC

Document management applications

25-29 Lausanne (Switzerland)

* TC 42 Photography

25-29 Dublin (Ireland) * TC 198 Sterilization of health care products

26 Paris (France) ** TC 4/SC 6 Rolling bearings/Insert bearings and accessories

26 Paris (France) ** TC 4/SC 9 Rolling bearings/Tapered roller bearings

26-27 Paris (France) ** TC 44/SC 8 Welding and allied processes/Equipment for gas welding, cutting and allied processes

26-29 Paris (France) * TC 172/SC 1 Optics and photonics/Fundamental standards

27 Paris (France) ** TC 4/SC 8 Rolling bearings/Load ratings and life


** TC 67/SC 3 Materials, equipment and offshore structures for petroleum, petrochemical and natural gas industries/Drilling and completion fluids, and well cements

28 Paris (France) ** TC 4/SC 11 Rolling bearings/Linear motion rolling bearings

28-29 Paris (France) TC 4 Rolling bearings


** TC 67/EC/MC Executive committee and Management committee

Japan * JTC 1/SC 24 Information technology/Computer graphics, image processing and environmental data representation

July 2007

1-6 Ibusuki (Japan) * TC 184/SC 4 Industrial automation systems and integration/Industrial data

9 Paris (France) ** TC 44/SC 9 Welding and allied processes/Health and safety

10 Paris (France) ** TC 44/SC 7 Welding and allied processes/Representation and terms

11-12 Paris (France) ** TC 44 Welding and allied processes

11-12 Paris (France) ** TC 44/SC 5 Welding and allied processes/Testing and inspection of welds


* TC 112 Vacuum technology

15-20 Las Vegas (USA) * TC 38/SC 1 Textiles/Tests for coloured textiles and colorants

15-20 Las Vegas (USA) * TC 38/SC 2 Textiles/Cleansing, finishing and water resistance tests

18 Schlieren (Switzerland)

** TC 44/SC 6 Welding and allied processes/Resistance welding

Sydney (Australia)

** TC 194 Biological evaluation of medical devices

August 2007

USA ** TC 37 and SCTerminology and other language and content resources

September 2007

7-14 Cheju Island (Korea, Republic of)

** TC 194 Biological evaluation of medical devices

10 Canada ** JTC 1/SC 35 Information technology/User interfaces

10-14 Jeju (Korea, Republic of)

** JTC 1/SC 25 Information technology/Interconnection of information technology equipment

10-14 Tienjin (China) * TC 150 and SC

Implants for surgery

10-14 Tienjin (China) * TC 150/SC 1 Implants for surgery/Materials

15-21 Goa (India) ** TC 61 and SCPlastics

More information: ISO Online - www.iso.orgStandards development - Meeting calendar


Documents

December 06