Upload
aubrey-green
View
219
Download
2
Embed Size (px)
Citation preview
DC Analysis Representation of diode into three models
Ideal case – model 1 with V = 0 Piecewise linear model 2 with V has a given value Piecewise linear model 3 with V and forward resistance, rf
Recall-Lecture 5
• Diode AC equivalent model– During analysis, must perform DC analysis first to
calculate ID in order to obtain rd
DC ANALYSIS
DIODE = MODEL 1 ,2 OR 3
CALCULATE DC CURRENT, ID
CALCULATE rd
AC ANALYSIS
DIODE = RESISTOR, rd
CALCULATE AC CURRENT, id
© Electronics© Electronics ECE 1231ECE 1231
Other Types of Diodes
Photodiode
Solar Cell
The term ‘photo’ means light. Hence, a photodiode converts optical energy into electrical energy. The photon energy breaks covalent bond inside the crystal and generate electron and hole pairs
Solar cell converts visible light into electrical energy. The working principle is the same as photodiode but it is more towards PROVIDING the power supply for external uses
© Electronics© Electronics ECE 1231ECE 1231
Schottky Barrier Diode
Light Emitting Diode
An LED is opposite of photodiode this time, it converts electrical energy into light energy – Normally GaAs is used as the material for LED. During diffusion of carriers – some of them recombines and the recombination emits light waves.
A Schottky Barrier diode is a metal semiconductor junction diode. The metal side is the anode while the n-type is the cathode. But the turn on voltage for Schottky is normally smaller than normal pn junction diode
© Electronics© Electronics ECE 1231ECE 1231
Breakdown VoltageThe breakdown voltage is a function of the doping concentrations in the n- and p-region of the pn junction.Large doping concentrations result in smaller break-down voltage.Reverse biased voltage – ET The electric field may become large enough for the covalent bond to break, causing electron-hole pairs to be created. So, electrons from p-type are swept to n-region by the electric field and holes from the n-type are swept to the p-regionThe movement will create reverse biased current known as the Zener Effect.
© Electronics© Electronics ECE 1231ECE 1231
Zener Effect and Zener Diode The applied reverse biased voltage cannot increase without limit since at
some point breakdown occurs causing current to increase rapidly.
The voltage at that point is known as the breakdown voltage, VZ
Diodes are fabricated with a specifically design breakdown voltage and are designed to operate in the breakdown region are called Zener diodes. Circuit symbol of the Zener diode:
Such a diode can be used as a constant-voltage reference in a circuit.
The large current that may exist at breakdown can cause heating effects and catastrophic failure of the diode due to the large power dissipated in the device.
Diodes can be operated in the breakdown region by limiting the current to a value within the capacities of the device.
NOTE: When a Zener diode is reverse-biased, it acts at the breakdown region, when it is forward biased, it acts like a normal PN junction diode
© Electronics© Electronics ECE 1231ECE 1231
Avalanche Effect While these carriers crossing the space-charge
region, they also gain enough kinetic energy. Hence, during collision with other atoms, covalent
bond is broken and more electron-holes pairs are created, and they contribute to the collision process as well. Refer to figure below
ehe atom
ehatomElectron with high kinetic energy
ehatom
© Electronics© Electronics ECE 1231ECE 1231
Zener Diode
ANSWER: ID = 0.2 mA
10 k
Calculate the value of the current ID if VZ = 10V
© Electronics© Electronics ECE 1231ECE 1231
The Zener diode with VZ = 4.7V is used in the circuit shown below and the input signal is a 20 V peak-to-peak square wave. Use V = 0 VSketch the output signal, vo.
HINT: When a Zener diode is reverse-biased, it acts at the breakdown region, when it is forward biased, it acts like a normal PN junction diode
+
Vin
-
+
Vo
-
R
Chapter 3Chapter 3Diode CircuitsDiode Circuits
VoltageVoltage RegulatorRegulator
A voltage regulator supplies constant voltage to a load.
Voltage Regulator - Zener Diode
The breakdown voltage of a Zener diode is nearly constant over a wide range of reverse-bias currents.
This make the Zener diode useful in a voltage regulator, or a constant-voltage reference circuit.
A Zener diode is connected in a voltage regulator circuit. It is given that VPS = 20V, the Zener voltage, VZ = 10V, Ri = 222 and PZ(max) = 400 mW.
a.Determine the values of IL, IZ and II if RL = 380 .b.Determine the value of RL that will establish PZ(max) = 400 mW in the diode.
Example
For proper function the circuit must satisfied the following conditions.
1.The power dissipation in the Zener diode is less than the rated value
2.When the power supply is a minimum, VPS(min), there must be minimum current in the zener diode IZ(min), hence the load current is a maximum, IL(max),
3.When the power supply is a maximum, VPS(max), the current in the diode is a maximum, IZ(max), hence the load current is a minimum, IL(min)
AND Or, we can write
For general thumb of rule for design this circuit is, so from the last Equation
Maximum power dispassion in the Zener diode is
EXAMPLE 1 (Example 3.3 from textbook) Consider voltage regulator is used to power the cell phone at 2.5 V from the lithium ion battery, which voltage may vary between 3 and 3.6 V. The current in the phone will vary 0 (off) to 100 mA(when talking).
Calculate the value of Ri and the Zener diode power dissipation
simple Zener diode voltage regulator circuit
Solution: The stabilized voltage VL = 2.5 V, so the Zener diode voltage must be VZ = 2.5 V. The maximum Zener diode current is
The maximum power dispassion in the Zener diode is
The value of the current limiting resistance is
• Example 2
Range of VPS : 10V– 14VRL = 20 – 100 VZ = 5.6VFind value of Ri and calculate the maximum power rating of the diode