MANUAL DE SERVIOVer 1.3 2002. 07 DAV-S500/S800 are composed of following models. As for the service manual, it is issued for each component model, then, please refer to them.

DAV-S500Brazilian Model

COMPONENT MODEL NAMEDAV-S500 COMPACT DISC DECK RECEIVER SYSTEM FRONT SPEAKER SYSTEM CENTER SPEAKER SYSTEM REAR SPEAKER SYSTEM SUBWOOFER SPEAKER SYSTEM HCD-S500 SS-TS500 SS-RS500 SS-RS500 SS-WS500

PARTS LISTPart No. 1-476-784-11 1-573-291-11 0 1-569-008-21 1-754-060-11 1-754-149-11 1-769-108-11 0 1-770-019-11 1-792-388-14 1-792-388-24 1-792-388-34 1-792-388-44 1-792-388-54 1-792-388-64 1-823-352-11 1-823-352-21 1-823-352-31 1-823-352-41 1-823-352-51 1-823-352-61 4-235-055-01 Description Remarks Part No. 4-235-681-21 4-235-681-31 4-235-681-41 4-235-681-51 4-235-681-61 4-235-681-71 4-236-189-11 4-236-189-21 4-236-189-31 Description Remarks REMOTE COMMANDER (RM-SS800) CONNECTOR, CONVERSION ADAPTOR, CONVERSION 2P (E32, SP, MY, EA) ANTENNA (FM) LOOP ANT (AM) CORD, CONNECTION (VIDEO) ADAPTOR, CONVERSION PLUG 3P (UK, HK) CORD (WITH CONNECTOR) (RED, 5m) (S500) CORD (WITH CONNECTOR) (BLK, 5m) (S500) CORD (WITH CONNECTOR) (WHT, 5m) (S500) CORD (WITH CONNECTOR) (YEL, 15m) (S500) CORD (WITH CONNECTOR) (BLU, 15m) (S500) CORD (WITH CONNECTOR) (GRN, 5m) (S500) CORD (WITH CONNECTOR) (RED, 5m) (S800) CORD (WITH CONNECTOR) (PURPLE, 5m) (S800) CORD (WITH CONNECTOR) (WHT, 5m) (S800) CORD (WITH CONNECTOR) (GRY, 15m) (S800) CORD (WITH CONNECTOR) (BLU, 15m) (S800) CORD (WITH CONNECTOR) (GRN, 5m) (S800) COVER, BATTERY (FOR RM-SS800) MANUAL, INSTRUCTION (FRENCH) (S500) MANUAL, INSTRUCTION (SPANISH) (S500) MANUAL, INSTRUCTION (CHINESE) (S500) MANUAL, INSTRUCTION (ARABIC) (S500) MANUAL, INSTRUCTION (KOREAN) (S500)

MANUAL, INSTRUCTION (PORTUGUESE) (S500) MANUAL, INSTRUCTION (ENGLISH) (S800) MANUAL, INSTRUCTION (FRENCH) (S800) MANUAL, INSTRUCTION (GERMAN, SPANISH, DUTCH, SWEDISH, ITALIAN, POLISH) (S800) 4-236-189-41 MANUAL, INSTRUCTION (DANISH, FINNISH, PORTUGUESE) (S800) 4-236-189-51 4-236-189-61 4-236-189-71 4-236-526-11 4-236-526-21 MANUAL, INSTRUCTION (ARABIC) (S800) MANUAL, INSTRUCTION (RUSSIAN) (S800) MANUAL, INSTRUCTION (CHINESE) (S800) MANUAL, INSTRUCTION (ENGLISH) (S500) MANUAL, INSTRUCTION (FRENCH) (S500)

4-235-681-11 MANUAL, INSTRUCTION (ENGLISH) (S500)

4-236-526-31 MANUAL, INSTRUCTION (GERMAN, SPANISH, DUTCH, SWEDISH, ITALIAN, POLISH) (S500) 4-236-526-41 MANUAL, INSTRUCTION (DANISH, FINNISH, PORTUGUESE) (S500) 4-236-887-01 CUSHION (FOR SS-RS500/TS500)Les composants identifis par une marque 0 sont critiques pour la scurit. Ne les remplacer que par une pice portant le numro spcifi.

The components identified by mark 0 or dotted line with mark 0 are critical for safety. Replace only with part number specified.

COMPACT AV SYSTEM9-873-259-012001G1600-1 2001.7

Sony CorporationHome Audio Company Shinagawa Tec Service Manual Production Group

MANUAL DE SERVIOVer 1.3 2002. 07

HCD-S500Brazilian Model

Photo : HCD-S500

HCD-S500 are the amplifier, DVD/CD and tuner section in DAV-S500.

Model Name Using Similar Mechanism Mechanism Type Base Unit Name Optical Pick-up Name

NEW CDM-55D-DVBU8 DVBU8 KHM-240AAA

SPECIFICATIONSAUDIO POWER SPECIFICATIONSPOWER OUTPUT AND TOTAL HARMONIC DISTORTION: With 6 ohm loads, both channels driven, from 120 10,000 Hz; rated 40 watts per channel minimum RMS power, with no more than 10 % total harmonic distortion from 250 milliwatts to rated output.

AM tuner sectionSystem Tuning range 530 1,710 kHz (with the interval set at 10 kHz) 531 1,710 kHz (with the interval set at 9 kHz) Tuner section: PLL quartz-locked digital synthesizer system

Amplifier section S500 MODELStereo mode Surround mode 40 W + 40 W (6 ohms at 1 kHz, THD 10 %) Front: 40 W + 40 W Center*: 40 W Rear*: 40 W + 40 W (6 ohms at 1 kHz, THD 10 %) Subwoofer*: 80 W (3 ohms at 100 Hz, THD 10 %) Antenna Loop antenna

Video sectionInputs Outputs Video: 1 Vp-p 75 ohms Video: 1 Vp-p 75 ohms S-video: Y: 1 Vp-p 75 ohms C: 0.286 Vp-p 75 ohms

General* Depending on the sound field settings and the source, there may be no sound output. Inputs (Analog) VIDEO 1, 2: Sensitivity: 150 mV Impedance: 50 kilohms VIDEO 2 (optical): Sensitivity: VIDEO 1 (AUDIO OUT): Voltage: 2 V Impedance: 1 kilohms PHONES: Accepts low- and high-impedance headphones DIGITAL OUT (CD) Sensitivity: Power requirements Brazilian models: 110 - 240V AC, 60 Hz

Inputs (Digital) Outputs (Analog)

Power consumption Dimensions (approx.) Mass (approx.) Operating temperature Operating humidity Supplied accessories

Outputs (Digital)

SACD/DVD systemLaser Semiconductor laser Signal format system NTSC or NTSC/PAL Frequency response (at 2 CH STEREO mode) DVD (PCM): 2 Hz to 22 kHz (1.0 dB) CD: 2 Hz to 20 kHz (1.0 dB) Signal-to-noise ratio More than 80 dB (VIDEO 1 (AUDIO) connectors only) Harmonic distortion Less than 0.03 %

98 W (120 V AC) 98 W (230 V AC) 355 70 378 mm (14 2 7/8 15 inches) (w/h/d) incl. projecting parts 4.0 kg (9 lb 8 oz) 5C to 35C (41F to 95F) 5 % to 90 % Check that you have the following items: Speakers (5) Subwoofer (1) AM loop antenna (1) FM wire antenna (1) Speaker cords (5m 4, 15m 2) (16ft. 4, 49ft. 2) Video cord (1) Remote commander (remote) RM-SS800 (1) R6 (size AA) batteries (2) Foot pads (15) Speakers-connection and Installation (card) (1) Quick reference for Remote commander (card) (1)

Design and specifications are subject to change without notice.

FM tuner sectionSystem Tuming range: Tuming range: Tuming range: Tuming range: Antenna Antenna terminals Intermediate frequency PLL quartz-locked digital synthesizer system 87.5 108.0 MHz (100 kHz step)

FM wire antenna 75 ohms, unbalanced 10.7 MHz

COMPACT AV SYSTEM

9-873-291-032002E1600-1 2002.05

Sony CorporationHome Audio Company Published by Sony Engineering Corporation

HCD-S500SAFETY CHECK-OUT After correcting the original service problem, perform the following safety checks before releasing the set to the customer: Check the antenna terminals, metal trim, metallized knobs, screws, and all other exposed metal parts for AC leakage. Check leakage as described below. LEAKAGE The AC leakage from any exposed metal part to earth Ground and from all exposed metal parts to any exposed metal part having a return to chassis, must not exceed 0.5 mA (500 microampers). Leakage current can be measured by any one of three methods. 1. A commercial leakage tester, such as the Simpson 229 or RCA WT-540A. Follow the manufacturers instructions to use these instruments. 2. A battery-operated AC milliammeter. The Data Precision 245 digital multimeter is suitable for this job. 3. Measuring the voltage drop across a resistor by means of a VOM or battery-operated AC voltmeter. The limit indication is 0.75 V, so analog meters must have an accurate low-voltage scale. The Simpson 250 and Sanwa SH-63Trd are examples of a passive VOM that is suitable. Nearly all battery operated digital multimeters that have a 2V AC range are suitable. (See Fig. A)To Exposed Metal Parts on Set

Laser component in this product is capable of emitting radiation exceeding the limit for Class 1. This appliance is classified as a CLASS 1 LASER product. The CLASS 1 LASER PRODUCT MARKING is located on the rear exterior.

This caution label is located inside the unit.

CAUTION

Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure. Notes on chip component replacement Never reuse a disconnected chip component. Notice that the minus side of a tantalum capacitor may be damaged by heat. Flexible Circuit Board Repairing Keep the temperature of soldering iron around 270C during repairing. Do not touch the soldering iron on the same conductor of the circuit board (within 3 times). Be careful not to apply force on the conductor when soldering or unsoldering.

0.15F

1.5k

AC voltmeter (0.75V)

Earth Ground

Fig. A. Using an AC voltmeter to check AC leakage.

SAFETY-RELATED COMPONENT WARNING!! COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE WITH MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUBLISHED BY SONY.

ATTENTION AU COMPOSANT AYANT RAPPORT LA SCURIT! LES COMPOSANTS IDENTIFS PAR UNE MARQUE 0 SUR LES DIAGRAMMES SCHMATIQUES ET LA LISTE DES PICES SONT CRITIQUES POUR LA SCURIT DE FONCTIONNEMENT. NE REMPLACER CES COMPOSANTS QUE PAR DES PISES SONY DONT LES NUMROS SONT DONNS DANS CE MANUEL OU DANS LES SUPPMENTS PUBLIS PAR SONY.

2

HCD-S500TABLE OF CONTENTS 1. SERVICING NOTE 5 2. GENERAL 6 3. DISASSEMBLY 8 4. TEST MODE 12 5. ELECTRICAL ADJUSTMENT 22 6. DIAGRAMS 256-1. Block Diagrams 26 RF/Servo, Video Section 26 CPU Section 27 Power Section 28 6-2. Printed Wiring Board RF Section 29 6-3. Schematic Diagram RF Section 30 6-4. Printed Wiring Board DVD Section (1/2) 31 6-5. Printed Wiring Board DVD Section (2/2) 32 6-6. Schematic Diagram DVD (1/8) Section 33 6-7. Schematic Diagram DVD (2/8) Section 34 6-8. Schematic Diagram DVD (3/8) Section 35 6-9. Schematic Diagram DVD (4/8) Section 36 6-10. Schematic Diagram DVD (5/8) Section 37 6-11. Schematic Diagram DVD (6/8) Section 38 6-12. Schematic Diagram DVD (7/8) Section 39 6-13. Schematic Diagram DVD (8/8) Section 40 6-14. Printed Wiring Board AMP Section (1/2) 41 6-15. Printed Wiring Board AMP Section (2/2) 42 6-16. Schematic Diagram AMP Section (1/2) 43 6-17. Schematic Diagram AMP Section (2/2) 44 6-18. Printed Wiring Board I/O Section 45 6-19. Schematic Diagram I/O Section (1/2) 46 6-20. Schematic Diagram I/O Section (2/2) 47 6-21. Printed Wiring Board Panel Section 48 6-22. Schematic Diagram Panel Section 49 6-23. Printed Wiring Board Front Section 50 6-24. Schematic Diagram Front Section 51 6-25. Printed Wiring Board Power Section 52 6-26. Printed Wiring Board Power Section 53 6-27. Schematic Diagram Power Section 54 6-28. Schematic Diagram Loading Section 55 6-29. Printed Wiring Board Loading Section 55 6-30. IC Block Diagrams 56 6-31. IC Pin Function Description 60

7. EXPLODED VIEWS7-1. 7-2. 7-3. 7-4. Main Section 70 Front Panel Section 71 Chassis Section 72 Mechanism Deck Section (CDM55D-DVBU8) 74

8. ELECTRICAL PARTS LIST 75

3

HCD-S500

Self-diagnosis Function(When letters/numbers appear in the display)When the self-diagnosis function is activated to prevent the system from malfunctioning. In this case a five-character service number (e.g., C 13 00) with a combination of a letter and digits appears on the screen and the front panel display. Refer to the following table.C:13:00

NOTES ON HANDLING THE OPTICAL PICK-UP BLOCK OR BASE UNIT The laser diode in the optical pick-up block may suffer electrostatic break-down because of the potential difference generated by the charged electrostatic load, etc. on clothing and the human body. During repair, pay attention to electrostatic break-down and also use the procedure in the printed matter which is included in the repair parts. The flexible board is easily damaged and should be handled with care. NOTES ON LASER DIODE EMISSION CHECK The laser beam on this model is concentrated so as to be focused on the disc reflective surface by the objective lens in the optical pickup block. Therefore, when checking the laser diode emission, observe from more than 30 cm away from the objective lens. LASER DIODE AND FOCUS SEARCH OPERATION CHECK Carry out the S curve check in CD section adjustment and check that the S curve waveform is output several times.

First three characters of the service number C 13

Cause and/or Corrective Action

C 31

E XX (xx is a number)

The disc is dirty. , Clean the disc with a soft cloth (page 9). The disc is not inserted correctly. , Re-insert the disc correctly. To prevent a malfunction, the system has performed the selfdiagnosis function. , Contact your nearest Sony dealer or local authorized Sony service facility and give the 5-character service number. Example: E 61 10

4

HCD-S500 SECTION 1 SERVICING NOTE

HOW TO OPEN THE DISC TRAY WHEN POWER SWITCH TURNS OFF

2 Pull-out the disc tray.

Cam

Hole of chassis

1 Turn the cam in the direction of the arrow.

When removing the disc tray, high torque is necessary to turn the ejection cam on the bottom surface. Therefore, the screw thread is easily damaged. To prevent this damage, turn it carefully.

5

HCD-S500 SECTION 2 GENERALThis section is extracted from instruction manual.

Index to Parts and ControlsFor more information, refer to the pages indicated in parentheses.

Front Panel

1 2 3 4 5

POWER switch/indicator (31) Disc tray (31) A OPEN/CLOSE (31) Front panel display (11) ./ > PREV/NEXT, PRESET +/ (29, 32) 6 H (play) (31) 7 X (pause) (32)

8 9 0 qa qs qd qf qg

x (stop) (31) PHONES jack (31) VOLUME control (31) SOUND FIELD +/ (47) DISPLAY (47, 60) BAND (29) FUNCTION (59) (remote sensor) (17)

Rear Panel

V I D E O O U T VIDEO IN

VIDEO IN

S V I D E O ( DVD ONLY)

SPEAKERAMA U D I O O U T AUDIO IN AUDIO IN FRONT R CENTER FRONT L

COAXIAL

L

L

OPTICAL DIGITAL IN

OPTICAL (CD ONLY) VIDEO

FM75

R

R

VIDEO 1

VIDEO 2

DIGITAL MONITOR OUT OUT

REAR R

WOOFER

REAR L

1 2 3 4 5

AM antenna (20) VIDEO 1 jacks (22) VIDEO 2 jacks (22) DIGITAL IN (OPTICAL) jack (23) DIGITAL OUT (OPTICAL) jack

6 MONITOR OUT (VIDEO/S VIDEO) jacks (22) 7 SPEAKER jacks (18) 8 FM 75 COAXIAL antenna jack (21)

6

HCD-S500

Remote

1 2 3 4 5 6 7 8 9 0 qa qs

TV "/1 (on/standby) (58) OPEN/CLOSE (31) NAME (61) STEREO/MONO (60) MEMORY (29) CLEAR (35) PLAY MODE (35) AUDIO (45) ANGLE (50) SUBTITLE (51) VOL +/ (60) ./> PREV/NEXT, TV/PRESET +/ (29, 32) H PLAY/SELECT (31) TITLE (33) DVD DISPLAY (38) C/X/x/c/ENTER (25) DVD SETUP (54) "/1 (on/standby) (31) DIMMER (28) TV/VIDEO (58) REPEAT (38) MUTING (32) TIME (42) FUNCTION (59) BAND (29) Number buttons (33) SOUND FIELD (47) DISPLAY (47, 60) ENTER CONTROL DVD/TV switch (58)

1 4 7>10

2 5 810/0

3 6 9

qd qf qg qh qj qk ql w; wa ws wd wf wg wh wj wk wl e;

NoteThis remote control glows in the dark. However, before glowing, the remote must be exposed to light for awhile.

ea m/M/ / SLOW, TUNING +/ (29, 39) es x STOP (31) ed X PAUSE (32) ef DVD MENU (34) eg O RETURN (34) eh AMP MENU (25)

7

HCD-S500 SECTION 3 DISASSEMBLY The equipment can be removed using the following procedure.Set Case (Top) Front panel section Loading board, Loading motor assembly (M901) RF-240 board Tray Optical pick-up (KHM-240AAA)

DVD mechanism deck (CDM550-DVBU8)

Note: Follow the disassembly procedure in the numerical order given.

1. CASE (TOP), DVD LID, LID WINDOW SUB ASSEMBLY4 Case (Top)

3 Four screws (+BVTP 3 8)

2 Two case screws

8 DVD lid, Lid window sub assembly

1 Two case screws 6 Pull-out the disc tray.

Cam7 Two claws

Hole of chassis5 Turn the cam in the direction of the arrow.

2. FRONT PANEL SECTION

3 Connector (CN902)

5 Two claws

1 Connector (CN309) 6 Front panel section 2 Flexible flat cable (15 core) (CN005) 4 Four screws (+BVTP 3 8)

8

HCD-S500

3. DVD MECHANISM DECK (CDM55D-DVBU8)

1 Two screws (DIA. 2.6 8)

2 MD cover

6 Screw (+BVTP 3 8) 8 Mechanism deck (CDM55D-DVBU8) 5 Flexible flat cable (25 core) (CN010) 4 Flexible flat cable (9 core) (CN009) 3 Connector (CN402)

7 Two claws

4. LOADING BOARD, LOADING MOTOR ASSEMBLY (M901)

1 Remove the belt (CDM55)

4 Motor (LD) assy (M901)

3 Two solderings

5 Loading board 2 Two screws (+BTP 2.6 6)

9

HCD-S500

5. RF-240 BOARD

2 Flexible flat cable (26P) (CN001)

4 RF-240 board

1 Flexible flat cable (25 core) (CN002)

3 Two screws (+BTP 2.6 6)

6. TRAY

1 While pushing the two protrusions, release the two claws fixing the tray and pull out the tray in the direction of the arrow A. (Be carefull of the two claws.)

A

2 Tray

10

HCD-S500

7. OPTICAL PICK-UP (KHM-240AAA)

8 Three insulators 5 Two step screws (M) 4 Step screw (L)

7

2 Flexible flat cable (9 core) 9 Optical pick-up (KHM-240AAA)

6 Holder (KHM-240)

3 Flexible flat cable (26 core)

1 Floating screw (+PTPWHM 2.6)

11

HCD-S500 SECTION 4 TEST MODE4-1. VERSION DISPLAY MODEProcedure: 1. Press the A button on the main unit or 1 button on the remote commander to turn the set on. 2. Press three buttons of FUNCTION , . PREV and A simultaneously for two seconds. 3. The message VER. 1. ** is displayed for a moment.

4-5. OSD TEST MODEProcedure: 1. Press the A button on the main unit or 1 button on the remote commander to turn the set on. 2. Set the FUNCTION to DVD. 3. While pressing two buttons of DISPLAY and x simultaneously, turn the VOLUME knob clockwise. 4. The Test Mode Menu is displayed on the TV screen. 5. To execute each function, select the number on the remote commander. 6. See the following section for explanation in detail. 7. To exit from this mode, press the POWER button to turn the set off.

4-2. JOG TEST MODEProcedure: 1. Press the A button on the main unit or 1 button on the remote commander to turn the set on. 2. Press three buttons of BAND , x and A simultaneously. 3. The fluorescent indicator displays JOG 0. The value JOG 0 increases like +1, +2, +3... if rotating the VOLUME knob clockwisw,or it decreases like 1, 2, 3,.... if rotating counterclockwise. 4. To exit from this mode, press the POWER button to turn the set off.

4-6. DISC TRAY LOCKProcedure: 1. Press the A button on the main unit or 1 button on the remote commander to turn the set on. 2. Press two buttons of DISPLAY and . PREV simultaneously for two seconds. 3. The message LOCKED is displayed and the tray is locked. (Even if exiting from this mode, the tray is still locked.) 4. Press two buttons of DISPLAY and . PREV simultaneously for two seconds again. 5. The message UNLOCKED is displayed and the tray is unlocked. 6. To exit from this mode, press the POWER button to turn the set off.

4-3. KEY TEST MODEProcedure: 1. Press the A button on the main unit or 1 button on the remote commander to turn the set on. 2. Press three buttons of DISPLAY , x and A simultaneously. 3. The message KEY NUM 0 is displayed and 0 blinks. 4. Each time a button is pressed, KEY NUM 0 value increases. However, once a button is pressed, it is no longer taken into account. 5. When all buttons are pressed, KEY NUM 11 appears and the number blinking is stopped. 6. To exit from this mode, press the POWER button to turn the set off.

4-7. GENERAL DESCRIPTIONThe Test Mode allows you to make diagnosis and adjustment easily using the remote commander and monitor TV. The instructions, diagnostic results, etc. are given on the on-screen display (OSD).

4-4. DISPLAY TEST MODEProcedure: 1. Press the A button on the main unit or 1 button on the remote commander to turn the set on. 2. Press three buttons of BAND , X and A simultaneously. 3. All segments are turned on.ALL 1 DISCS AUTO PRO LOGIC D D DIGITAL FM AM NTSC PBC ANGLE TITLE TRACK CHAPTER INDEX HTUNED M MONO ST S D D dts PCM dB REPEAT 1 kHz PROGRAM MHz SHUFFLE

4-8. STARTING TEST MODESet the FUNCTION to DVD with the main unit power on. Next, while pushing the x button and the [DISPLAY] button on the main unit at the same time, turn the VOLUME knob to the right to start Test Mode and display the menu shown below on the TV screen. At the bottom of the menu screen, the model name and revision number are displayed. To execute each function, select the desired menu and press its number on the remote commander. To exit from Test Mode, press the [POWER] button.Test Mode Menu

4.

When the NEXT > button is pressed, the display will light up as follows.TITLE TRACK CHAPTER INDEX HTUNED M MONO ST SD D dts PCM dB REPEAT 1 kHz PROGRAM MHz SHUFFLE

ALL 1 DISCS AUTO PRO LOGIC D D DIGITAL FM AM NTSC PBC ANGLE

0. 1. 2. 3. 4. 5. 6.

Syscon Diagnosis Drive Auto Adjustment Drive Manual Operation Mecha Aging Emergency History Version Information Video Level Adjustment Exit: POWER Key

5.

Press the NEXT > button, confirm the display.

_ Model : HCX-1030_xx Revision: 1.xxx

6. 7. 8.

Press the NEXT > button, all segments are turned off. Every pressing of the NEXT > button turns on each segments in the same order. To exit from this mode, press the POWER button to turn the set off.

12

HCD-S500

4-9.

SYSCON DIAGNOSIS

The same contents as board detail check by serial interface can be checked from the remote commander. On the Test Mode Menu screen, press [0] key on the remote commander, and the following check menu will be displayed.### Syscon Diagnosis ### Check Menu Quit All Version Peripheral Servo Supply AV Decoder Video Audio DSD Decoder

Press x key to quit the diagnosis, or [PREV] key to repeat the same item where an error occurred, or [NEXT] key to continue the check from the item next to faulty item. Selecting 2 and subsequent items calls the submenu screen of each item. For example, if 5. Supply is selected, the following submenu will be displayed.### Syscon Diagnosis ### Check Menu No. 5 Supply Quit All ARP Register Check ARP to RAM Data Bus ARP to RAM Address Bus ARP RAM Check

0. 1. 2. 3. 4. 5. 6. 7. 8. 9. _

0. 1. 2. 3. 4. 5. _

0. Quit Quit the Syscon Diagnosis and return to the Test Mode Menu. 1. All All items continuous check This menu checks all diagnostic items continuously. Normally, all items are checked successively one after another automatically unless an error is found, but at a certain item that requires judgment through a visual check to the result, the following screen is displayed for the key entry.### Syscon Diagnosis ### Diag All Check No. 2 Version 2-3. ROM Check Sum Check Sum = 2005

0. Quit Quit the submenu and return to the main menu. 1. All All submenu items continuous check This menu checks 2 and subsequent items successively. At the item where visual check is required for judgment or an error occurred, the checking is suspended and the message is output for key entry. Normally, all items are checked successively one after another automatically unless an error is found. Selecting 2 and subsequent items executes respective menus and outputs the results. For the contents of each submenu, see Check Items List. General Description of Checking Method 2. Version (2-2) Revision ROM revision number is displayed.Error: Not detected. The revision number defined in the source file of ROM (At the beginning of mass production, the Flash ROM of IC107 is used, but midway it is replaced by the IC108 OTP ROM. IC107 or IC108) is displayed with four digits. Below IC107 are all IC107 or IC108. (2-3) ROM Check Sum Check sum is calculated. Error: Not detected. The 8-bit data are added at addresses 0x000F0000 ~ 0x002EFFFF of ROM (IC107) and the result is displayed with 4-digit hexadecimal number. Error is not detected. Compare the result with the specified value. (2-4) Model Type Model code is displayed. Error: Not detected. The model code read from EEPROM (IC101) is displayed with 2-digit hexadecimal number. (2-5) Region Region code is displayed. Error: Not detected. The region code determined from the model code is displayed.

Press NEXT Key to Continue Press PREV Key to Repeat _

For the ROM Check, the check sum calculated by the Syscon is output, and therefore you must compare it with the specified value for confirmation. Following the message, press [NEXT] key to go to the next item, or [PREV] key to repeat the same check again. To quit the diagnosis and return to the Check Menu screen, press x or [ENTER] key. If an error occurred, the diagnosis is suspended and the error code is displayed as shown below.### Syscon Diagnosis ###

3-3. EEPROM Check Error 03: EEPROM Write/Reed N Address : 00000001 Write Data : 2492 Read Data : 2490 Press NEXT Key to Continue Press PREV Key to Repeat _

13

HCD-S500

3. Peripheral (3-2) EEPROM Check Data write read, and accord check Error 03: EEPROM write/read discord Data 0x9249, 0x2942, 0x4294 are written to addresses 0x00~0xFF of EEPROM (IC101), then read and checked. Before writing, the data are saved, then after checking, they are written to restore the contents of EEPROM. 4. Servo (4-2) Servo DSP Check Data write read, and accord check Error 12: Read data discord Data 0x9249, 0x2942, 0x4294 are written to the address 0x602 of RAM in the Servo DSP (IC302), then read and checked. (4-3) DSP Driver Test Test signal data DSP Driver Error: Not detected. Caution: Do not conduct this test with a mechanical deck connected. The maximum voltage is applied to the Servo Driver IC (IC401, IC802). If mechanical deck is connected, the motor and optics could be damaged. Disconnect mechanical deck following the output message, then enter specified 4or 5-digit number from the remote commander, and press the [ENTER]. The test is conducted only when the input data accord. Check the output level, then press the [NEXT] to finish the test. This test is skipped if All is selected. Supplement: How to disconnect mechanical deck Disconnect flat cables connected to the CN009 and CN010 of MB-82/85 board. Also, disconnect harness from the CN402. 5. Supply Caution: Do not conduct this check with a mechanical deck connected. An access is made to the stream supply and servo control IC (IC302) and external RAM (IC303) using check data. If mechanical deck is connected, the motor and optics could be damaged. This check is also executed by the All menu item. Supplement: How to disconnect mechanical deck Disconnect flat cables connected to the CN009 and CN010 of DVD board. Also, disconnect harness from the CN402. (5-2) ARP Register Check Data write read, and accord check Error 08: ARP register write, and read data discord Data 0x00 to 0xFF are written to the TMAX register (address 0xC6) in ARP (IC302), then they are read and checked.

(5-3) ARP to RAM Data Bus Data write read, and accord check Error 09: ARP RAM data bus error Data 0x0001 to 0x8000 where one bit each is set to 1 are written to the address 0 of RAM (IC303) connected to the ARP (IC302) through the bus, then they are read and checked. In case of discord, written bit pattern and read data are displayed. If data where multiple bits are 1 are read, the bits concerned may touch each other. Further, if data where certain bit is always 1 or 0 regardless of written data, the line could be disconnected or shorted. (5-4) ARP to RAM Address Bus Data write other address read discord check Error 10: ARP RAM address bus error Caution: Address and data display in case of an error is different from the display of other diagnosis (described later). Before starting the test, all addresses of RAM (IC303) are cleared to 0x0000. First, 0xA55A is written to the address 0x00000, and the address data are read and checked from addresses 0x00001 to 0x80000 while shifting 1 bit each. Next, the data at that address is cleared, and it is written to the address 0x00001, and read and checked in the same manner. This check is repeated up to the address 0x80000 while shifting the address data by 1 bit each. If data other than 0 is read at the addresses except written address, an error is given because all addresses were already cleared to 0. In this check, the error display pattern is different from that of other diagnosis; read data, written address, and read address are displayed in this order. However, the message uses same template, and accordingly exchange Address and Data when reading. The following display, for example,### Syscon Diagnosis ###

5-4. ARP to RAM Address Bus Error 10: ARP - RAM Address B Address : 0000A55A Write Data : 00000000 Read Data : 00080000 Press NEXT Key to Continue Press PREV Key to Repeat _

shows the data 0xA55A was read from address 0x00080000 though it was written to the address 0x00000000. This implies that these addresses are in the form of shadow. Also, if the read data is not 0xA55A, another error will be present. (5-5) ARP RAM Check Data write read, and accord check Error 11: ARP RAM read data discord The program code data stored in ROM are copied to all areas of RAM (IC303) connected to the ARP (IC302) through the bus, then they are read and checked if they accord. If the detail check was selected initially, the data are written to all areas and read, then the same test is conducted once again with the data where all bits are inverted between 1 and 0. If discord is detected, faulty address, written data, and read data are displayed following the error code 11, and the test is suspended.

14

HCD-S500

6.

AV Decoder

Check Items List 2) Version (2-2) Revision (2-3) ROM Check Sum (2-4) Model Type (2-5) Region 3) Peripheral (3-2) EEPROM Check 4) Servo (4-2) Servo DSP Check (4-3) DSP Driver Test 5) Supply (5-2) ARP Register Check (5-3) ARP to RAM Data Bus (5-4) ARP to RAM Address Bus (5-5) ARP RAM Check 6) AV Decoder (6-2) 1930 RAM (6-3) 1930 SP 7) Video (7-2) Color Bar (7-3) Composit Out (7-4) Y/C Out (7-6) Component Out 8) Audio (8-2) ARP 1930 (8-3) Test Tone 9) DSD Decoder (9-2) 2752 ID Check (9-3) 2752 RAM Check Error Codes List 00: Error not detected 01: RAM write/read data discord 02: Gate array NG 03: EEPROM NG 08: ARP register read data discord 09: ARP RAM data bus error 10: ARP RAM address bus error 11: ARP RAM read data discord 12: Servo DSP NG 13: 1930 SDRAM NG 14: ARP 1930 video NG 15: ARP 1930 audio NG 16: 1910 UCODE download NG 17: System call error (function not supported) 18: System call error (parameter error) 19: System call error (illegal ID number) 20: System call error (time out) 90: Error occurred 91: User verification NG 92: Diagnosis cancelled

(6-2) 1930 RAM Data write read, and accord check Error 13: AVD RAM read data discord The program code data stored in ROM (IC107 or IC108) are copied to all areas ooRAM (IC504, IC505) connected to the AVD (IC503) through the bus, then they are read and checked if they accord. Further, the same test is conducted once again with the data where all bits are inverted between 1 and 0. If discord is detected, faulty address, written data, and read data are displayed following the error code 13, and the test is suspended. (6-3) 1930 SP ROM AVD RAM Video OUT Error: Not detected. The data including sub picture streams in ROM (IC107 or IC108) are transferred to the RAM (IC504, IC505) in AVD (IC503), and output as video signals from the AVD (IC503). They are output from all video terminals (Composite, Y/C). 7. Video

(7-2) Color Bar AVD color bar command write Video OUT Error: Not detected. The command is transferred to the AVD, and the color bar signals are output from video terminals. They are output from all video terminals (Composite, Y/C). (7-3) Composit Out (7-4) Y/C Out (7-6) Component Out 8. Audio

(8-2) ARP 1930 Error 14 : ARP 1930 video NG 15 : ARP 1930 audio NG (8-3) Test Tone All channels 2ch Left 2ch Right Front Left Front Right Rear Left Rear Right Center Sub Woofer 9. DSD Decoder

(9-2) 2752 ID Chack (9-3) 2752 RAM Check

15

HCD-S500

4-10. DRIVE AUTO ADJUSTMENTOn the Test Mode Menu screen, press [1] key on the remote commander, and the drive auto adjustment menu will be displayed.## Drive Auto Adjustment ## Adjustment Menu 0. 1. 2. 3. 4. ALL DVD-SL CD DVD-DL LCD

1. DVD-SL (single layer) Select [1], insert DVD single layer disc, and press [ENTER] key, and the adjustment will be made through the following steps, then adjusted values will be written to the EEPROM. DVD Single Layer Disc Adjustment Steps 1. SLED TILT Reset 2. Disc Check Memory SL 3. Wait 300 msec 4. Set Disc Type SL 5. LD ON 6. Spdl Start 7. Wait 1 sec 8. Focus Servo ON 0 9. Auto Track Offset Adjust 10. CLVA ON 11. Wait 500 msec 12. Tracking ON 13. Wait 1 sec 14. Sled ON 15. Check CLV Lock 16. Auto LFO Adjust 17. Auto Focus Offset Adjust 18. Auto Tilt Position Adjust 19. Auto Focus Gain Adjust 20. Auto Focus Offset Adjust 21. EQ Boost Adjust 22. Auto LFO Adjust 23. Auto Track Gain Adjust, Search Check 24. 32Tj Fwd 25. 32Tj Rev 26. 500Tj Fwd 27. 500Tj Rev 28. All Servo Stop 29. Eep Copy Loop Filter Offset

Exit: RETURN

Normally, [0] is selected to adjust DVD (single layer), CD, DVD (dual layer), and SACD in this order. But, individual items can be adjusted for the case where adjustment is suspended due to an error. In this mode, the adjustment can be made easily through the operation following the message displayed on the screen. The disc used for adjustment must be the one specified for adjustment. However, for SACD disc, use the player with initial data if the disc is not available. 0. ALL Select [0] and press [ENTER] key, and the servo set data in EEPROM will be initialized. Then, 1. DVD-SL disc, 2. CD disc, 3. DVD-DL disc, and 4. SACD disc are adjusted in this order. Each time one disc was adjusted, it is ejected. Replace it with the specified disc following the message. Though the message to confirm whether discs other than SACD disc are adjusted is not displayed, you can finish the adjustment if pressing the x button. During adjustment of each disc, the measurement for disc type judgment is made. As automatic adjustment does not judge the disc type unlike conventional models, take care not to insert wrong type discs. Also, do not give a shock during adjustment.

16

HCD-S500

2.

CD

3.

DVD-DL (dual layer)

Select [2], insert CD disc, and press [ENTER] key, and the adjustment will be made through the following steps, then adjusted values will be written to the EEPROM. CD Adjustment Steps 1. Sled Tilt Rest 2. Disc Check Memory CD 3. Wait 500 msec 4. Set Disc Type CD 5. LD ON 6. Spdl Start 7. Wait 500 msec 8. Focus Servo ON 0 9. Auto Track Offset Adjust 10. CLVA ON 11. Wait 500 msec 12. Tracking ON 13. (TC Display Start) 14. Wait 1 sec 15. Jitter Display Start 16. Sled ON 17. Check CLV ON 18. Auto LFO Adjust 19. Auto Focus Offset Adjust 20. 21. Auto Focus Gain Adjust 22. Auto Focus Offset Adjust 23. Eq Boost Adjust 24. Auto LFO Adjust 25. Auto Track Gain Adjust, Search Check 26. 32Tj Fwd 27. 32Tj Rev 28. 500Tj Fwd 29. 500Tj Rev 30. All Servo Stop

Select [3], insert DVD dual layer disc, and press [ENTER] key, and the adjustment will be made through the following steps, then adjusted values will be written to the EEPROM. DVD Dual Layer Disc Adjustment Steps 1. Sled Tilt Reset 2. Disc Check Memory DL 3. Wait 500 msec 4. Set Disc Type DL 5. LD ON 6. Spdl Start 7. Wait 1 sec, Layer 1 Adjust 8. Focus Servo ON 0 9. Auto Track Offset Adjust 10. 11. 12. 13. 14. 15. 16. 17. 18. 19. 20. 21. 22. 23. 24. 25. 26. 27. 28. 29. 30. 31. 32. 33. 34. 35. 36. 37. 38. 39. 40. 41. 42. 43. 44. 45. 46. 47. 48. Clva ON Wait 500 msec Tracking ON Wait 500 msec Sled ON Check CLV Lock Auto Loop Filter Offset Auto Focus Adjust Auto Focus Gain Adjust Auto Focus Offset Adjust Eq Boost Adjust Auto Loop Filter Offset Auto Track Gain Adjust, Search Check 32Tj Fwd 32Tj Rev 500Tj Fwd 500Tj Rev, Layer 0 Adjust Fj (L1 -> L0) Auto Track Offset Adjust L0 Clva ON Wait 500 msec Tracking ON Wait 500 msec Sled ON Check CLV Lock Auto Focus Filter Offset Auto Focus Adjust Auto Focus Gain Adjust Auto Focus Offset Adjust Eq Boost Adjust Auto Loop Filter Offset Auto Track Gain Adjust, Search Check 32Tj Fwd 32Tj Rev 500Tj fwd 500Tj Rev, Layer Jump Check Lj (L0 -> L1) Lj (L1 -> L0)

49. All Servo Stop

17

HCD-S500

4. LCD Select [4], insert SACD disc, and press [ENTER] key, and the adjustment will be made through the following steps, then adjusted values will be written to the EEPROM. However, if SACD disc is not available, use the player with initial data, skipping the SACD adjustment. In this case, you can finish the adjustment if pressing the x button. SACD Adjustment Steps 1. Sled Tilt Reset 2. Set Disc Type CD 3. LD ON 4. Spdl Start 5. Wait 500 msec 6. Focus Servo ON 0 7. Auto track Offset Adjust 8. 9. CLVA ON 10. Wait 500 msec 11. Tracking ON 12. Wait 1 sec 13. Sled ON 14. Check CLV ON 15. Auto Focus Offset Adjust 17. 18. Auto Focus Gain Adjust 19. Auto Focus Offset Adjust 20. Eq Boost Adjust 21. Auto LFO Adjust 22. Auto Track Gain Adjust 23. 24. 25. 26. 32Tj Fwd 32Tj Rev 500Tj Fwd 500Tj Rev

4-11. DRIVE MANUAL OPERATIONOn the Test Mode Menu screen, select [2], and the manual operation menu will be displayed. For the manual operation, each servo on/ off control and adjustment can be executed manually.## Drive Manual Operation ## Operation Menu Disc type Servo Control Track/Layer Jump Manual Adjustment Auto Adjustment Memory Check Sacd Water Mark

1. 2. 3. 4. 5. 6. 7.

0. Disc Check Memory _ Exit: Return

In using the manual operation menu, take care of the following points. These commands do not provide protection, thus requiring correct operation. The sector address or time code field is displayed when a disc is loaded. 1. Set correctly the disc type to be used on the Disc Type screen. The disc type must be set after a disc was loaded. The set disc type is cleared when the tray is opened. 2. After power ON, if the Drive Manual Operation was selected, first perform Reset SLED TILT by opening 1. Disc Type screen. 3. In case of an alarm, immediately press the x button to stop the servo operation, and turn the power OFF. Basic operation (controllable from front panel or remote commander)

27. All Servo Stop */

[POWER]x

[OPEN/CLOSE] [RETURN] [NEXT], [PREV] [1] to [9], [0]Cursor UP/DOWN

Power OFF Servo stop Stop+Eject/Loading Return to Operation Menu or Test Mode Menu Transition between sub modes of menu Selection of menu items Increase/Decrease in manually adjusted value

18

HCD-S500

0.

Disc Check MemoryDisc Check

1. SL Disc Check 2. CD Disc Check 3. DL Disc Check

0. Reset SLED TILT _

Disc Type Disc Type Auto Check DVD SL 12 cm DVD DL 12 cm CD 12cm LCD 12 cm DVD SL 8 cm DVD DL 8 cm CD 8 cm LCD 8 cm Reset SLED TILT TC. : : EMG. 00 CD 12 cm 1. 2. 3. 4. 5. 6. 7. 8. 9. 0.

Display when CD 12cm disc was selectedOn this screen, the mirror time is measured to judge the disc and it is written to the EEPROM. First load DVD SL disc and press [1], next load CD disc and press [2], and finally load DVD DL disc and press [3]. The adjustment must be executed more than once after default data were written. External vibration or shock to the player must not be given. Reference value for DVD is from 10 to 20, and for CD, from 28 to 4F. Check that the value of CD is larger than that of DVD. When those values are beyond a range perform this adjustment again. From this screen, you can go to another mode by pressing [NEXT] or [PREV] key, but you cannot enter this mode from another mode. You can enter this mode from the Operation Menu screen only. 1. Disc Type

[0] Reset SLED TILT [1] Disk Type Check

Reset the Sled and Tilt to initial position. Judge automatically the loaded disc. As the judged result is displayed at the bottom of screen, make sure that it is correct. If Disc Check Memory menu has not been executed after EEPROM default setting, the disc type cannot be judged. In this case, return to the initial menu and make a check for three types of discs (SL, DL, CD). Select the loaded disc. The adjusted value is written to the address of selected disc. No further entry is necessary if [1] was selected.

[2] to [9]Disc Type 1. Disc Type Auto Check 2. DVD SL 12 cm 3. DVD DL 12 cm 4. CD 12cm 5. LCD 12 cm 6. DVD SL 8 cm 7. DVD DL 8 cm 8. CD 8 cm 9. LCD 8 cm 0. Reset SLED TILT -- SA. ------ SI. -EMG. 00 DVD SL12cm

2. Servo ControlServo Control LD Off R.Sled FWD SP Off L.Sled REV Focus Off TRK. Off Sled Off CLVA Off FCS. Srch Off

1. 2. 3. 4. 5. 6. 7.

On this screen, select the disc type. To select the disc type, press the number of the loaded disc. The selected disc type is displayed at the bottom. Selecting [1] automatically selects and displays the disc type. In case of wrong display, retry Disc Check Memory. Also, opening the tray causes the set disc type to be cleared. In this case, set the disc type again after loading. In performing manual operation, the disc type must be set. Once the disc type has been selected, the sector address or time code display field will appear as shown below. These values are displayed when PLL is locked.Disc Type Disc Type Auto Check DVD SL 12 cm DVD DL 12 cm CD 12cm LCD 12 cm DVD SL 8 cm DVD DL 8 cm CD 8 cm LCD 8 cm Reset SLED TILT SA. SI. EMG. 00 DVD SL 12 cm 1. 2. 3. 4. 5. 6. 7. 8. 9. 0.

0. Reset SLED TILT SA. SI. DVD SL 12 cm

EMG. 00

On this screen, the servo on/off control necessary for replay is executed. Normally, turn on each servo from 1 sequentially and when CLVA is turned on, the usual trace mode becomes active. In the trace mode, DVD sector address or CD time code is displayed. This is not displayed where the spindle is not locked. The spindle could run overriding the control if the spindle system is faulty or RF is not present. In such a case, do not operate CLVA.

Display when DVD SL 12cm disc was selected

19

HCD-S500

[0] Reset SLED TILT [1] LD [2] SP [3] Focus [4] TRK [5] Sled [6] CLVA [7] FCS. Srch

Reset the Sled and Tilt to initial position. Turn ON/OFF the laser. Turn ON/OFF the spindle. Search the focus and turn on the focus. Turn ON/OFF the tracking servo. Turn ON/OFF the sled servo. Turn ON/OFF normal servo of spindle servo. Apply same voltage as that of focus search to the focus drive to check the focus drive system. Move the sled outward. Perform this operation with the tracking servo turned off. Move the sled inward. Perform this operation with the tracking servo turned off. Move the tilt upward. Move the tilt downward.

6. Memory CheckEEPROM Data1 - DL CD LCD SL L0 L1 Focus Gain xx xx xx xx xx TRK. Gain xx xx xx xx xx FCS Balance xx xx xx xx xx Focus Bias xx xx xx xx xx TRV. Offset xx xx xx xx xx L. F. Offset xx xx xx xx xx EQ Boost xx xx xx xx xx Mirror Time xx xx xx xx xx _DOWN: Next Data CLEAR: Default Set page.1/2

EEPROM Data1 CD xx xx xx xx xx xx xx - DL LCD SL L0 -xx xx -xx --xx --xx --xx -xx xx xx xx xx xx L1 xx ----xx xx

Sled FWD

Sled REV

RF Jitter RF Level FE Level FE Balance TRV. Level Analog FRSW PLL DacGain _ UP : Prev Data CLEAR: Default Set

page.2/2

Tilt UP Tilt DOWN

The following menus are normally not used. 3. Track/Layer Jump 4. Manual Adjustment 5. Auto Adjustment

This screen displays current servo adjusted data stored in the EEPROM. Though adjusted data can be initialized with the [CLEAR] key, they cannot be restored after initialization. So, before clearing, make a note of the adjusted data. For reference, the drive has been designed so that the gain center value is 20 and offset value is 80. Other values will be in a range of 10 to 80. If extreme value such as 00 or FF is set, adjustment will be faulty. In such a case, check for disc scratch or cable disconnection, then perform adjustment again. 7. Sacd Water Mark

The persons who do not know well about these menus should not use them.

4-12. MECHA AGING### Mecha Aging ###

Press OPEN Key

Abort: STOP key

On the Test Mode Menu Screen, selecting [3] executes the aging of the mechanism. Start aging with PLAY. During aging, the repeat cycle is displayed. Aging can be aborted at any time by pressing the x key. After the operation is stopped, press the x key or [RETURN] key again to return to the Test Mode Menu. SEARCH Aging is only for a CD.

20

HCD-S500

4-13. EMERGENCY HISTORY### EMG. History ### Laser Hours CD DVD xxxxxxxh xxxxxxxh

1. 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 2. 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 Select: 1 9 Scroll: UP/DOWN (1: Last EMG.) Exit: RETURN

On the Test Mode Menu screen, selecting [4] displays the information such as servo emergency history. The history information from last 1 up to 10 can be scrolled with key or key. Also, specific information can be displayed by directly entering that number with ten keys. The upper two lines display the laser ON total hours. Data below minutes are omitted. Clearing History Information Clearing laser hours Press [DISPLAY] and [CLEAR] keys in this order. Both CD and DVD data are cleared. Clearing emergency history Press [TITLE] and [CLEAR] keys in this order. Initializing set up data Press [DVD] and [CLEAR] keys in this order. The data have been initialized when Set Up Initialized message is displayed. The EMG. History screen will be restored soon. How to see Emergency History 3 1 2

34: Focus gain adjustment error 35: Tilt servo adjustment error 36: RF equalizer adjustment error 37: RF group delay adjustment error 38: Jitter value after adaptive servo operation is too large. 40: Focus servo does not operate. 41: With a dual layer (DL) disc, focus jump failed.50: CLV (spindle) servo does not operate. 51: Spindle does not stop. 60: With a DVD disc, Syscon made a request to seek nonexistent address. 61: With a CD disc, Syscon made a request to seek nonexistent address. 62: With a CD disc, Syscon made a request to seek nonexistent track No. and index No. 63: With a DVD disc, seeking of target address failed. 64: With a CD disc, seeking of target address failed. 65: With a CD disc, seeking of target index failed. 70: With a DVD disc, physical information data could not be read. 71: With a CD disc, TOC data could not be read. 80: Disc type judgment failed. 81: As disc type judgment failed, retry was repeated. 82: As disc type judgment failed, a measurement error occurred. 83: Disc type could not be judged within the specified time. 84: Illegal command code was received from Syscon. 85: Illegal command was received from Syscon.

4-14. VERSION INFORMATION## Version Information ## IF con. Ver: x. xxx (xxxx) Group 00 Ver: x. xxx (xxxx) Model xx Region 0x

SYScon.

1.2 1 : Emergency Code 2 : Dont Care These codes are used for verification of software designing. 3 : Historical order 1 to 9 Emergency Codes List 10: Communication to IC001 (RF-240 board) failed. 11: Each servo for focus, tracking, and spindle is unlocked. 12: Communication to EEPROM, IC101 (DVD board) failed. 13: Writing of hours meter data to EEPROM, IC101 (DVD board) failed. 14: Communication to Servo DSP IC302 (DVD board) failed, or Servo DSP is faulty. 20: Initialization of tilt servo and sled servo failed. They are not placed in the initial position. 21: Tilt servo operation error 22: Syscon made a request to move the tilt servo to wrong position. 23: Sled servo operation error 24: Syscon made a request to move the sled servo to wrong position. 30: Tracking balance adjustment error 31: Tracking gain adjustment error 32: Focus balance adjustment error 33: Focus bias adjustment error

Servo DSP Ver:X.XXX OPT Type:2 Laser Exit: RETURN

On the Test Mode Menu screen, selecting [5] displays the ROM version and region code. The parenthesized hexadecimal number in version field is checksum value of ROM.

4-15. VIDEO LEVEL ADJUSTMENTOn the Test Mode Menu screen, selecting [6] displays color bars for video level adjustment. During display of color bars, OSD disappears but the menu screen will be restored if pressing any key. : MONITOR OUT VIDEO (75 terminating resistance) Measuring instrument : Oscilloscope Adjustment device : RV501 on DIGITAL board Specified value : 1.0 0.02 Vpp Measurement point

1.0 0.02 Vp-p

21

HCD-S500 SECTION 5 ELECTRICAL ADJUSTMENTIn making adjustment, refer to 5-2. Adjustment Related Parts Arrangement. Note: During diagnostic check, the characters and color bars can be seen only with the NTSC monitor. Therefore, for diagnostic check, use the monitor that supports both NTSC and PAL modes This section describes procedures and instructions necessary for adjusting electrical circuits in this set. Instruments required: 1) Color monitor TV 2) Oscilloscope 1 or 2 phenomena, band width over 100 MHz, with delay mode 3) Frequency counter (over 8 digits) 4) Digital voltmeter 5) Standard commander * RM-SS800 (1-418-838-11) 6) DVD reference disc HLX-501 (J-6090-071-A) (dual layer) HLX-503 (J-6090-069-A) (single layer) HLX-504 (J-6090-088-A) (single layer) HLX-505 (J-6090-089-A) (dual layer) 7) SACD reference disc HLXA-509 (J-6090-090-A) * Use only the designated remote control when adjusting this system component.

5-1. ADJUSTMENT OF VIDEO SYSTEM1. Video Level Adjustment (DVD BOARD) This adjustment is made to satisfy the NTSC standard, and if not adjusted correctly, the brightness will be too large or small. Mode Signal Test point Instrument Adjusting element Specification Video level adjustment in test mode Color bars MONITOR OUT (VIDEO) connector (75 terminated) Oscilloscope RV501 1.0 0.02 Vp-p

Adjusting method: 1) In the test mode initial menu 6 Video Level Adjustment, set so that color bars are generated. 2) Adjust the RV501 to attain 1.0 0.02 Vp-p.

1.0 0.02 Vp-p

Figure 5-12. S-terminal Output Check Check S-terminal video output. If it is incorrect, pictures will not be displayed correctly in spite of connection to the TV with a Sterminal cable. Mode Signal Test point Instrument Specification Video level adjustment in test mode Color bars S VIDEO OUT (S-Y) connector (75 terminated) Oscilloscope 1.0 0.1 Vp-p

Checking method: 1) In the test mode initial menu 6 Video Level Adjustment, set so that color bars are generated. 2) Confirm that the S-Y level is 1.0 0.1 Vp-p.

1.0 0.1 Vp-p

Figure 5-2

22

HCD-S500

3. Checking S Video Output S-C (DVD BOARD) This checks whether the S-C satisfies the NTSC Standard. If it is not correct, the colors will be too dark or light. Mode Signal Test point Instrument Specification Connection:CN003

5-2. ADJUSTMENT RELATED PARTS ARRANGEMENTDVD BOARD (SIDE A)2 CN003 1 RV501 VIDEO LEVEL ADJ 9

Video level adjustment in test mode Color bars CN003 pin 2 Oscilloscope 286 50 mVp-p

100F+ 2 Oscilloscope

75 1%

100k 1%3

Checking method: 1) Confirm that the S-C burst is 286 50 mVp-p.

286 50 mVp-p

Figure 5-3

23

HCD-S500 SECTION 6 DIAGRAMSCIRCUIT BOARDS LOCATION

SW (B)-1030 board PW-1030 board

Power board

AMP board

DDCON-1030 board RR-1030 board FU-1030 board SW (A)-1030 board HP-1030 board

RF-240 board

Loading board

TUNER UNIT I/O board

FP-1030 board

DVD board

24

HCD-S500

THIS NOTE IS COMMON FOR PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS. (In addition to this, the necessary note is printed in each block.) For schematic diagrams.Note: All capacitors are in F unless otherwise noted. pF: F 50 WV or less are not indicated except for electrolytics and tantalums. All resistors are in and 1/4 W or less unless otherwise specified. f : internal component. C : panel designation.Note: The components identified by mark ! or dotted line with mark ! are critical for safety. Replace only with part number specified. Note: Les composants identifis par une marque ! sont critiques pour la scurit. Ne les remplacer que par une pice portant le numro spcifi.

WAVEFORMS RF-240 BOARD

DVD BOARD

AMP BOARD

I/O BOARD

1For printed wiring boards.Note: X : parts extracted from the component side. a : Through hole. b : Pattern from the side which enables seeing. (The other layers' patterns are not indicated.) Caution: Pattern face side: (Conductor B) Parts face side: (Component A)500mV/DIV 1.5Vp-p 100ns/DIV

73.5Vp-p

qs7.2 Vp-p

qf2.5Vp-p H

6.25ns (16MHz)

20.3ns (49.152MHz)

IC001 tl (SIGO) DVD PLAY

IC901 ek (X2)

IC300 4

IC701 qf, qg Test Mode (Video)

2Parts on the pattern face side seen from the pattern face are indicated. Parts on the parts face side seen from the parts face are indicated.1.5Vp-p 500mV/DIV 400ns/DIV

83.8Vp-p

qd5 Vp-p

qg2Vp-p

81.4ns (12.288MHz)

13 s

H

Indication of transistorC QBC E These are omitted

IC001 tl (SIGO) CD PLAY

IC606 w; (XMCK)

IC305 qd (OUTL1+)

IC701 9, 0 Test Mode (Video)

3These are omitted1.8Vp-p 500mV/DIV 40ms/DIV

93.5Vp-p

qh0.9Vp-p H

A : B+ Line. B : B Line. H : adjustment for repair. Voltages and waveforms are dc with respect to ground under no-signal (detuned) conditions. Voltages and waveforms are dc with respect to ground in service mode. Waveforms are taken with a oscilloscope. Voltage variations may be noted due to normal production tolerances. no mark : STOP Circled numbers refer to waveforms. Signal path. F : FM J : CD c : DVD g : VIDEO G :Y d : CHROMA Abbreviation AR : Argentina model AUS : Australian model CND : Canadian model EA : Saudi Arabia model E12 : 220-240V AC area in E model E32 : 110-240V AC area in E model HK : Hong Kong model KR : Korean model MX : Mexican model MY : Malaysia model SP : Singapole model TW : Taiwan model

B E

74ns (13.5MHz)

IC001 ra (TE) DVD PLAY

IC607 qs (MCLK2)

Q700 E Test Mode (Video)

41.8Vp-p 500mV/DIV 200ms/DIV

02Vp-p

37ns (27MHz)

IC001 ra (TE) CD PLAY

IC102 7 (XTI)

5190mVp-p 100mV/DIV 40ms/DIV

qa3.4 Vp-p

60.6ns (16.5MHz)

IC001 rs (FE) DVD PLAY

IC103 td (X1)

6840mVp-p 500mV/DIV 40ms/DIV

IC001 rs (FE) CD PLAY

25

25

HCD-S5006-1. BLOCK DIAGRAMS RF/SERVO, VIDEO SECTION OPTICAL PICK-UP (KHM-240 AAA/J1RP)RF A-D IC001 DVD/CD RF AMP DIGITAL SERVO 2 RF IN 14 11 7 E-H VC Q001 DVD/CD LD MOD DVD LD DVD LD DRIVE Q002 CD LD PD VR SW CD LD DRIVE 26 CD LD 21 DVD PD 22 CD PD 24 LD SEL 10 15 18 A-D A2-D2 E-H SIGO 59 IC302 SERVO DSP 131 RFIN1 128 RFIN2 TE 41 TZIN 40 FE 42 PI 36 PIIN 35 MON 44 MIRR 33 25 DVD LD TZC 37 DFT 38 SCLK 47 SDEN 48 SWD 46 SRD 45 LDON 27 VCI 39 LIMIT SENSOR 136 ADC1 137 ADC2 172 PGIN 144 ADC7 197 MIRR 196 TZC 185 DFCTI 175 SCK 180 GIO13 174 SDO 173 SDI 142 ADC5 143 ADC6 MA0-9 135 ADC0 D0-7 2 9 11 15 A0-7 . 17 19 44 51 MD0-15 . 53 60 27 36 MEMD0-15 IC303 16M DRAM 22 HA0-7 8 HD8-15 8 16 IC503 AV DECODER 232 2 235 5 . . HD0-15 237 7 240 10 218 203 215 200 . . 213 198 210 195 . . 208 193 . 205 192 VIDEO IN VIDEO2 3 2 HAD0-21 COMP OUT 80 Y OUT 74 MEMA0-9 C OUT 77 5 4 VIDEO IN VIDEO1 J600 (1/4) 1 7 IC702 OUTPUT SEL 11 14 12 8 9 7 16 1 2 DO 20 31 SDI0-7 8 8 34 . DTI0-7 36 39 WSAD0-7 8 177 157 . . 174 159 . . 171 162 . . 22 CDIN2 23 CDIN1 25 CDBCK 26 CDLRK 41 ICLK 44 ISTART 45 IVAL 43 IERR 224 HWAITOB 221 HRWB 220 HSCB SDAQ0-11 168 SDDQ0-15 . 165 . 163 . 164 . 167 . SPDIF 3 6 7 INC 5 4 INB IC700 INPUT SEL IC701 VIDEO AMP 2 INA OUTA1 15 OUTA2 14 J600 (2/4) OUTB1 13 OUTB2 12 VIDEO OUTC1 10 OUTC2 9 MUTE 1 Q700,702,703 BUFFER Q701,704 OFFSET SWITCH VMUTE VSEL2 VSEL1 Y C J700 MONITOR OUT 4 2 3 1 S VIDEO VIDEO OUT VIDEO1

DVD/CD PDIC

19 VC

XMWR 38 XRAS 41 XOE 42 XCAS 39 73 76 SD0-7 . 78 81 AD0-7 96 103

AAUDIO-1 SECTION

166 INT2 IC401 FOCUS/TRACKING COIL DRIVE SPINDLE/SLED/LOADING MOTOR DRIVE 40 SVC FDRV+ FDRVTDRV+ TDRVSLE MDSO 204 PDM2 205 PDM3 202 PDM0 203 PDM1 139 ADC3 159 MDSO 161 MDPO 45 SLED MOTOR DRIVE LOADING MOTOR DRIVE 7 10 16 17 15 TSDM 22 MUTE5 21 5 MUTE12 19 MUTE34 20 POWER SAVE 39 24 HCS 23 XCS SPFG SLDA SLDB LMP LMM LMCTL TSD SP MUTE 140 ADC4 198 PWM0 199 PWM1 176 GIO9 177 GIO10 200 PWM2 168 GIO2 167 GIO0

DMAIN SECTION

PLCKO 95 DOUT 66 DATA 62 BCLK 63 LRCK 65 SDCK 68 XSHD 69 XSAK 71 SDEF 72 XWAT 25 XWR 207 XRD 208 TDO 195

IC504,505 16M SDRAM IC601 VIDEO 5V 3 5V REG 1 10V

FOCUS COIL

FCS +/-

37 . 36 35 . 34 27 . 28 47 46

FOCUS COIL DRIVE TRACKING COIL DRIVE SPINDLE MOTOR DRIVE

48 1 3 4 5

TRACKING COIL

TRK +/-

170 . 160 173 . . 158 176 134 130 . . 131 133 . . 128 136 . . 125 . 124 . 127 139 . 137 . 140

SPINDLE MOTOR

M

SPM +/-

13

SLED MOTOR

M

SLA +/SLB +/-

32 29 25 . 24

SDCS0B 144 SDCS1B 143 SDDQM0 155 SDDQM1 154 SDCLK 149 SDCKE 146 SDWEOB 152 SDCKSOB 151 SDRASOB 147

LOADING M MOTOR

LDM +/-

TCK 194 TMS 192 TRST 191 IC304 XSRQ 70 5 6 XDSPRST 156 XARPRST 157 1 2

120 TCK 121 TMS 122 TRST

46 IREQ

231 RSTB 12 ACLK 29 CRPCLK 182 SCLK 180 CLK 227 DMREQ1 229 DMREQ0 223 HIREQO AVDD6 181 AVDD7 184 AVDD8 187

A3.3V RV501 VRIF 84 VIDEO LEVEL D3.3V IC501 1 1.8V REG 2

CHUCK SENSOR

187 MCKI 189 SCKI 182 CLKIN HINT 22 XINT 21

TRAY SENSOR

X102 27MHz

IC102 7 15 512FS AVD 33M AVD 27M AVD IC801 PLAYBACK SIGNAL PROCESSOR 111 8 114 . WAD0-7 117 120 TDO 29

190 HAD23 191 HAD22 228 DMACK0 226 DMACK1

R-CH is omitted due to same as L-CH. Signal Path : FM : CD : DVD: VIDEO

10 8 CLOCK 13 GEN 3 14

118 TDI

HA1-21 21

IC108 OPT

169 HD0-15 16 IC802 2 4 8 176

SD0-7 DSAL 64 DSAC 69 DSALFE 71 DSALS 74 BCKAO 60 EXCKO 13 SDATAL SDATAC SDATALF SDATALS DSBC DSMCK

123 WCK 166 SDCK 165 XSHD 167 XSAK 168 SDEF 164 XSRQ

:Y : CHROMA

BAUDIO SECTION

HA1-21 IC107 21 16M FLASH

27 TDI TDO HD0-15 16 26 TCK 30 TMS 31 TRST EXCKO 11 MCK 9 XRST

139 136 DQ0-7 . 134 131 162 152 .

IC803 16M SDRAM

22 78 57 56 48 84 63 62 81 102 109 . 111 118 . 120 . 1 5 17 18 36 35 67 70 71 58

16 85 100 40 46 49 16 60 61 50 47 76 A0-11 TRM/XKRCS 8 INT5 21 INT6 22 SI1 28 SO1 29 IC103 (1/2) SYSTEM CONTROL SC1 30 2 XMSLAT 7 MSREADY 10 SMUTE 6 MSDATO 4 MSDATI 3 MSCK

DREQ0

DREQ1

HA0-21

XLDON

XDRVMUTE

OCSW2

OCSW1

HD0-15

DACK1

TRM + XKRRST

48/44.1K

CKSW1

XARPRST

XWAIT

DACK0

XWRH

XFRST

XRST

CS0X

159 151 . . 157 149 . 154 148

CS5X

CS4X

INT0

CS2X

CS3X

INT1

INT2

XRD

IC804 D2.5V 3 2.5V REG 1 D3.3V

DCLK 141 DCKE 142 XWE 143 XCAS 144 XRAS 145

WIDE 82 TRST

CCPU SECTION

26

26

HCD-S500 CPU SECTION IC600 INPUT SEL J600 (3/4) AUDIO IN L VIDEO1 1 5 2 4 AUDIO IN L VIDEO2 A B 10 9 Q603 Q604 RF/SERVO SECTION ASEL2 ASEL1 OPTICAL DIGITAL IN VIDEO 2 IC602 OUT 3 3 IC606 DIGITAL AUDIO I/F RECEIVER 4 DIN1 3 DIN0 DO DIGDI DIGCLK CSDIR 35 DO 36 DI 38 CL 37 CE 22 XIN 21 XOUT DATA 16 CKOUT 13 BCK 14 LRCK 15 XSTATE 17 ERROR 34 R-CH TUN DO TUN DI TUN CLK TUN CE TUN STE Q607 FM DET X601 4.332MHz 13 X1 S500: AEP,UK / S800 MODEL Q908 Q909 59 EXLOCK 69 GP8 IC604 RDS 4 MUX 14 X0 RDATA 2 RDATA RCLK 79 INIT FM7.5V Q600-602 FM +B SWITCH 9.5V FM ON AUDIO 24 48 XMODE SDATAL SDATAC XMCK 20 SPDIF 2 IC602 AUDIO A/D CONV 1 LIN 16 SYSCLK 6 RSTB DOUT 15 BCK 14 LRCK 13 IC612 DIGITAL AUDIO PROCESSOR 57 EXID2 58 EXID1 59 EXI MCK 55 EXI BCK 56 EXI LRCK F2FLREX1 47 F2CSWEX2 46 F2SLR 45 F2BCK 43 F2LRCK 44 CKOUT 49 18 SDI1 30 SDI2 114 SDI3 17 BCKI1 29 BCKI2 63 DSIFL 65 DSICT 66 DSISW 67 DSISL 62 DSBCKF 52 MCK 77 SELEXT 78 SYNC 15 LRCKI1 28 LRCKI2 22 KFSIO 9 MCLK1 12 MCLK2 SCK 14 BCK 20 LRCK 19 GP10 67 108 98 . . 107 80 . D0-15 105 77 . 102 75 . 99 72 112 82 . . 110 85 . DIGDI DIGCLK Q910 HCS 33 HD IN 34 HCLK 36 HCS 113 PM 56 BST 2 XRST IC103 (2/2) SYSTEM CONTROL A0-15 109 83 . . 97 66 92 64 IC605 WE0 45 CS0 44 GP9 68 HACN 32 HDOUT 35 SCDT SHIFT LAT1 LAT2 LAT3 12 INIT NS MUTE PG MUTE IC101 SDA 38 SCL 39 WP 7 5 6 7 EEPROM Q902 MUTE HP MUTE HP SW CN101 SI0 4 SO0 SC0 XIFCS 5 6 EN DIAG RELAY 2.5V 3 2.5V REG 1 DA3V IC604 SRAM DIGDI DIGCLK LT IC608 AUDIO D/A CONV 2 DATA X601 13.5MHz 16 MCLK 1 BCK 3 LRCK 13 DATA 14 CLK 15 LT ROUT 8 R-CH Q606 MUTE R-CH LOUT 7 5 IC607 AUDIO DSP SDO1 23 SDO2 24 SDO3 25 SDO4 26 D1 D2 D3 SCK BCKO LRCKO 3 IC603 1

IC603 1 IN DIGITAL OUT OPTICAL (CD ONLY)

A

SPDIF

X600 12.288MHz

EAUDIO-2 SECTION

TUNER BLOCK UNITFM L-CH R-CH DI AM DO CK CE TUNED FM DET

BRF/SERVO VIDEO SECTION

SDATALF SDATALS DSBC DSMCK

IC610

J600 (4/4) 7 AUDIO OUT VIDEO1

RCLK 16

Q900 MUTE CONT IC601 10V IC600 5V 3 5V REG 1 3 10V REG 1 12V

IC900

IC900

IC900

IC900

IC900

X101 X1 53

4

2

6

Q903 MUTE

8

10

IC900

X0 54

3

1

5

9

11

13

FAUDIO-2 SECTION

RCLK

TUN DI

TUN CE

TUN CLK

TUN STE

TUN DO

FM ON

DO

DIG DI

DIG CLK

CS DIR

RDATA

HCS

3

XIFINT 2 XFRRST 1 FR 8

LT

100

93

96 98 99 89 95 94

24 7

8 19 13 32

23

18

20

17

33

22

48

12 15 11

6

14

16

44

1

2 28 29 30 31 26 25 49 46 55 50

DIR XMODE

DSP HACN

DSP PLOCK

AU MUTE

DSP RST

DSP GP9

DIR ERR

DIR XST

DSP PM

DSP BST

DSP DO

DIR AD

SYNC

FM

OCP

FL MUTE

RDSCLK

DIR DO

DIR CE

DIG DI

TUN DI

TUN DO

TUN CE

TUN END

DIG CLK

DAMP CLK

DSP CS

DAC CS

TUN CLK

AD RST

DAMP RST

DAMP MUTEN

DAMP MUTG

DAMP DATA

RELAY

HPSW

CS1

CS2

I2HLP

CS3

IC902 SERIAL PARALLEL P0 24 ASEL1 ASEL2

70 FR R-CH is omitted due to same as L-CH. Signal Path : FM : CD : DVD XIFCS 51: VIDEO

SI0 25 SO0 26 1 IC106 2 4 IC106 5 12IC106 13 3

4 SDI

SERI DATA 61 SERI CLK 62

26 DI1

P1 23 P13 7

3 CLK P14 6 15 DO1 P12 8 4 LATCH P2 22 2 RSTB P3 21 DVD PW 11 DIMM 12

3 IFSC0 IC901 CPU 5 CLK

IO DATA 63 IO LAT 64 IO RST 65

VSEL1 VSEL2 VMUTE

SC0 27

6

DVIDEO SECTION

11

68 XVIFCS 67 XFRINT V MUTE 45

FL CLK

FL CS

X1

39

38

X2

: CHROMA

66 XFRRST

91

92

82 81 80

83 84

54 53 56 IC802 FL DRIVER

34 Q901 RESET RST 60 G1 12 40 51

90

STOP

43

STPOW

RESET

SIRCS

MA MUTE 83

69 IFOK

FL DATA

:Y

RDS DATA

INT4 20

KEY2

KEY1

KEY0

ENA

ENB

PCONT2 PCONT1 RESET

X901 16MHz RF/SERVO SECTION

GPOWER SECTION

IC101 REMOTE CONTROL 1 RECEIVER

C

TRST

SIRCS SWITCH

RESET

FUNCTION KEY S821-825 S806 FUNCTION KEY

VOL ENCODER

AD1

AD2

S800 VOLUME

g

4

3

DAT5 6.5V

S1 35 39

D812

Q801 LED DRIVE

FL801 FLUORESCENT INDICATOR TUBE

CLK

CS

Q906,907

IC903,904

S801-805

63 62 61

Q803,804 T801 DC/DC CONV 6.5V

POWER

27

27

HCD-S500 POWER SECTION

IC305 STREAM PROCESSOR D1 D2 43 DATA OUTL1+ 24 OUTL2+ 15 OUTR1+ 10 OUTR2+ 1 64 XFS1 44 BCK 45 LRCK 38 SCDT 37 SCSHIFT 36 SCLATCH 41 INIT 39 NSPMUTE 40 PGMUTE IC300 2 4 28 XFS0IN 74 FSOI X300 49.152MHz XFSOOUT 77 FSOCKO 73 OUTL1- 21 OUTL2- 18 OUTR1- 7 OUTR2- 4 IC401 5 6 R-CH R-CH R-CH R-CH

IC301 POWER DRIVER (F) 8 INA 11 INB 7 EN 12 DIAG OUTB 17 OUTA 2

J401 (1/2) L401,C451 LPF L401,C452 LPF L402,C453 LPF L402,C454 LPF RY301 +27V L REAR L FRONT

EAUDIO-1 SECTION

D3 SCK BCKO LRCKO

7 +6.5V IC004 DA +5V IC005 DA +3,3V 3 +3.3V 1 REG 3 +5V REG 1 2

IC903 +6.5V 1 REG 5

Q906 T901 POWER TRANS

IC906 DVD +3.3V IC006 +1.8V J401 (2/2) L403,C455 LPF L403,C456 LPF L404,C457 LPF L404,C458 LPF WOOFER M +12V IC003 D +5V RY302 A +5V IC001 A +3,3V 3 +3.3V 1 REG 3 3 +5V REG IC002 +5V REG 1 1 Q001 CENTER Q911 Q907 +12V Q002 +12V SWITCH Q909 POWER SWITCH 3 +1.8V 1 REG Q910 2 +3,3V 1 REG 5

D911 RECT

D902

LF901,902 F901 LINE FILTER

S901 POWER AC IN

IC308STREAM PROCESSOR 43 DATA 64 XFS1 44 BCK 45 LRCK 38 SCDT 37 SCSHIFT 36 SCLATCH 41 INIT 39 NSPMUTE 40 PGMUTE 28 XFS0IN 74 FSOI XFSOOUT 77 OUTR1+ 10 OUTR2+ 1 OUTL1+ 24 OUTL2+ 15

IC306 POWER DRIVER (C) 8 INA 11 INB 7 EN 12 DIAG IC307 POWER DRIVER (W) 8 INA 11 INB 7 EN 12 DIAG OUTB 17 OUTA 2 OUTB 17 OUTA 2

D910

D909 RECT Q901-903 REG

IC901 SWITCHING REG 3 D 2 S 4 VCC 5 GND PC901 1 FB/OCP

D906

IC902 1 ERROR 2 AMP Q905

IC310STREAM PROCESSOR 43 DATA 64 XFS1 44 BCK 45 LRCK 38 SCDT 37 SCSHIFT 36 SCLATCH SCDT SHIFT LAT1 LAT2 LAT3 INIT 28 XFS0IN 74 FSOI 41 INIT 39 NSPMUTE 40 PGMUTE OUTL1+ 24 OUTL2+ 15 OUTR1+ 10 OUTR2+ 1 R-CH R-CH

IC309 POWER DRIVER (R) 8 INA 11 INB 7 EN 12 DIAG OUTB 17 OUTA 2 E +5.6V 3

Q908 IC905 +5.6V 1 REG D917 PC902 IC907 P.CONT2 R-CH J900 Q900 MUTE PHONES P.CONT1 IC904 RESET 5 RESET 1 2 D913

GCPU SECTION

Q915

FCPU SECTION

NS MUTE PG MUTE EN DIAG RELAY HP MUTE HP SW

1 2

IC312 4

Q301 RELAY DRIVE R-CH is omitted due to same as L-CH. Signal Path : FM : CD

IC302 +5V IC303 +3,3V 3 +3.3V 1 REG 3 +5V REG 1 +6.5V : DVD: VIDEO

:Y : CHROMA

28

28

HCD-S5006-2. PRINTED WIRING BOARD RF SECTION

IC001

Semiconductor

LocationRef. No. D001 D004 IC001 Q001 Q002 Location C-1 C-2 C-2 C-2 C-3

29

29

HCD-S5006-3. SCHEMATIC DIAGRAM RF SECTION See page 25 for Wavefoms. See page 58 for IC Block Diagrams.

IC B/D

30

30

HCD-S5006-4. PRINTED WIRING BOARD DVD SECTION (1/2)

(Page 53) 57 29

Semiconductor

LocationRef. No. D901 D903 D904 IC002 IC004 IC005 IC101 IC103 IC106 IC302 IC503 IC606 IC607 IC612 IC801 IC802 IC900 IC901 IC903 IC904 Q903 Location E-2 E-1 D-1 A-5 E-3 E-3 B-1 C-2 B-1 B-3 B-5 E-4 D-5 D-4 D-3 E-3 E-3 E-2 D-1 D-1 E-2

42

IC302IC106

IC503

42

IC101

IC103

RV501 VIDEO LEVEL ADJ

45

(Page48)

IC903

IC904

IC801

IC612 IC607

IC802

45

IC901 IC606 IC005 IC004 IC900EXCEPT S500:KR S800:EA,HK,TW,AUS

31

31

HCD-S5006-5. PRINTED WIRING BOARD DVD SECTION (2/2)

Semiconductor

LocationRef. No. D900 D902 Location D-6 E-6 A-2 A-2 A-1 C-2 C-5 C-5 B-4 B-3 B-5 B-3 B-2 B-2 E-1 E-1 E-2 E-1 D-2 E-3 E-2 E-2 D-4 D-5 D-3 A-1 A-1 E-6 E-6 D-5 D-6 D-6

IC001 IC003 IC006IC501

IC401

IC504

IC304

IC303

IC502

IC505IC108

IC001 IC003 IC006 IC102 IC107 IC108 IC303 IC304 IC401 IC501 IC504 IC505 IC600 IC601 IC602 IC603 IC604 IC605 IC608 IC610 IC803 IC804 IC902 Q001 Q002 Q900 Q901 Q902 Q906 Q907

IC1007

IC102

IC604IC804

IC902 IC803

IC603

IC610

IC608

IC602 IC601IC600 IC605

32

32

HCD-S5006-6. SCHEMATIC DIAGRAM DVD (1/8) SECTION See page 25 for Wavefoms. See page 56 for IC Block Diagrams.

IC B/D

33

33

HCD-S5006-7. SCHEMATIC DIAGRAM DVD (2/8) SECTION See page 25 for Wavefoms.

IC B/D

34

34

HCD-S5006-8. SCHEMATIC DIAGRAM DVD (3/8) SECTION

35

35

HCD-S5006-9. SCHEMATIC DIAGRAM DVD (4/8) SECTION

36

36

HCD-S5006-10. SCHEMATIC DIAGRAM DVD (5/8) SECTION See page 67 for IC Pin Function Description.

37

37

HCD-S5006-11. SCHEMATIC DIAGRAM DVD (6/8) SECTION See page 62 for IC Pin Function Description.

38

38

HCD-S5006-12. SCHEMATIC DIAGRAM DVD (7/8) SECTION

39

39

HCD-S5006-13. SCHEMATIC DIAGRAM DVD (8/8) SECTION See page 25 for Wavefoms. See page 56 for IC Block Diagrams. See page 60 for IC Pin Function Description.

IC B/D

38

37

35

35

40

40

HCD-S5006-14. PRINTED WIRING BOARD AMP SECTION (1/2)

Semiconductor

LocationRef. No. D330 D331 D332 D333 D334 D335 D340 D341 D342 D343 D344 D345 IC300 IC303 IC305 IC308 IC310 IC312 Location E-3 D-3 C-3 B-3 B-3 A-3 E-5 D-5 C-5 C-5 B-5 A-5 E-5 E-6 D-5 C-5 A-5 A-6

IC310

S500 : US,CND,AEP, CIS,UK,MX,KR,S800

IC308

S500 : US,CND,AEP, CIS,UK,MX,KR,S800

IC3051

IC3033

IC3005 1 4 3

S500 : US,CND,AEP, CIS,UK,MX,KR,S800

S500 : US,CND,AEP, CIS,UK,MX,KR,S800

41

41

HCD-S5006-15. PRINTED WIRING BOARD AMP SECTION (2/2)

50

Semiconductor

LocationRef. No.R347 R346

Location D-4 B-4 C-4 B-4 D-4 A-4 E-4 B-4 C-4 C-4 D-4 A-4 B-5 E-3 D-4 C-4 B-4 B-4 A-4 E-2 D-2 D-2 C-4 B-2 A-2 E-3 D-1 B-3 C-3 B-3 D-3 A-3 B-6

IC311S500 : US,CND,AEP, CIS,UK,MX,KR,S800

31

IC304

31

IC307

D310 D311 D312 D313 D314 D315 D320 D321 D322 D323 D324 D325 D351 D370 D371 D372 D373 D374 D375 D380 D381 D382 D383 D384 D385 IC301 IC302 IC304 IC306 IC307 IC309 IC311 Q301

S500 : US,CND,AEP,CIS, UK,MX,KR,S800

R421

IC306

3

IC3021

IC309

IC301C301

1

4

53

42

42

R420

HCD-S5006-16. SCHEMATIC DIAGRAM AMP SECTION (1/2)

Ver 1.1 2002.01

S500:US,CND,AEP, CIS,UK,MX,KR/S800

S500:US,CND,AEP, CIS,UK,MX,KR/S800

S500:US,CND,AEP,CIS,UK,MX,KR/S800

S500:US,CND,AEP, CIS,UK,MX,KR/S800 S500:US,CND,AEP,CIS, UK,MX,KR/S800

S500:US,CND,AEP, CIS,UK,MX,KR/S800

S500:US,CND,AEP, CIS,UK,MX,KR/S800

0.1 : S500/US,CND,AEP,CIS,UK,MX,KR,S800 0.01 : EXCEPT S500/US,CND,AEP,CIS,UK,MX,KR,S800 10p : EXCEPT S500/US,CND,AEP,CIS,UK,MX,KR,S800 47p : S500/US,CND,AEP,CIS,UK,MX,KR,S800

1uH : S500/US,CND,AEP,CIS,UK,MX,KR,S800 1.2uH : EXCEPT S500/US,CND,AEP,CIS,UK,MX,KR,S800

43

43

HCD-S5006-17. SCHEMATIC DIAGRAM AMP SECTION (2/2) See page 25 for Wavefoms.

0.1 : S500/US,CND,AEP,CIS,UK,MX,KR,S800 0.01 : EXCEPT S500/US,CND,AEP,CIS,UK,MX,KR,S800 S500 : US,CND,AEP,CIS,UK,MX,KR,S800 100/10V : S500/US,CND,AEP,CIS,UK,MX,KR,S800 0.1/50V : EXCEPT S500/US,CND,AEP,CIS,UK,MX,KR,S800 0.1/16V : S500/US,CND,AEP,CIS,UK,MX,KR,S800 0.01/25V : EXCEPT S500/US,CND,AEP,CIS,UK,MX,KR,S800

100/35V : S500/US,CND,AEP,CIS,UK,MX,KR,S800 100/50V : EXCEPT S500/US,CND,AEP,CIS,UK,MX,KR,S800

2200/35V : S500/US,CND,AEP,CIS,UK,MX,KR,S800 2200/50V : EXCEPT S500/US,CND,AEP,CIS,UK,MX,KR,S800

RELAY (24V) : S500/US,CND,AEP,CIS,UK,MX,KR,S800 RELAY (12V) : EXCEPT S500/US,CND,AEP,CIS,UK,MX,KR,S800

S500 : US,CND,AEP,CIS,UK,MX,KR,S800

44

44

HCD-S5006-18. PRINTED WIRING BOARD I/O SECTION

1

IC603

3

1

IC602

3

IC601 IC600

IC700 IC701 IC702

C612

TUNER UNIT

(Page 31)

IC604

CIS,

(Page 31)

1

2

3

4

5

6

7

8

9Ref. No. D601 D602 IC600 IC601 IC602 IC603 IC604 IC700 Location D-9 D-10 B-10 A-8 A-8 A-8 D-10 B-9

10 Semiconductor LocationRef. No. IC701 IC702 Q600 Q601 Q602 Q603 Q604 Location B-7 B-8 D-9 E-10 E-10 B-10 B-10

11Ref. No. Q605 Q606 Q607 Q700 Q701 Q702 Q703 Q704 Location B-10 B-10 D-10 A-8 A-7 B-8 B-7 A-8

45

45

HCD-S5006-19. SCHEMATIC DIAGRAM I/O SECTION (1/2) See page 57 for IC Block Diagrams.

CIS,

IC B/D

IC B/D

EXCEPT S500:AEP,UK

46

46

HCD-S5006-20. SCHEMATIC DIAGRAM I/O SECTION (2/2) See page 25 for Wavefoms.

47

47

HCD-S5006-21. PRINTED WIRING BOARD PANEL SECTION

31

IC802

KTO FU-1030 BOARD CNP808 (Page 50)

IC101

1 Semiconductor

2

3

4

5

LocationRef. No. D806 D807 D808 D809 D810 Q803 Q804 Location B-4 B-4 B-4 B-4 B-3 B-2 B-2

48

48

HCD-S5006-22. SCHEMATIC DIAGRAM PANEL SECTION See page 57 for IC Block Diagrams.

IC B/D

49

49

HCD-S5006-23. PRINTED WIRING BOARD FRONT SECTION

I(Page 42)

K(Page 48)

50

50

HCD-S5006-24. SCHEMATIC DIAGRAM FRONT SECTION

51

51

HCD-S5006-25. PRINTED WIRING BOARD POWER SECTION (1/2)

52

52

HCD-S5006-26. PRINTED WIRING BOARD POWER SECTION (2/2) Semiconductor

LocationRef. No. D901 D902 D903 D904 D905 D906 D907 D908 D909 D910 D911 D912 D913 D914 D915 D916 D917 D918 D920 D921 IC901 IC902 IC903 IC904 IC905 IC906 IC907 Q901 Q902 Q903 Q905 Q906 Q907 Q908 Q909 Q910 Q911 Q915 Location D-4 B-4 E-5 E-5 D-4 D-4 D-4 D-4 E-2 D-2 B-2 B-1 E-2 D-2 E-3 D-1 E-3 E-1 D-2 E-2 D-5 B-1 D-1 E-2 E-3 C-1 E-1 D-5 E-5 E-5 C-1 D-2 E-2 D-2 E-2 D-1 D-2 E-2

S901

J(Page 42)

IC902

IC906

IC903

IC901

E

IC905

H(Page 31)

IC904

53

53

HCD-S500

Ver 1.2 2002.05 6-27. SCHEMATIC DIAGRAM POWER SECTION See page 59 for IC Block Diagrams.

FMB-G14L

IC B/D

IC907

54

54

HCD-S5006-28. SCHEMATIC DIAGRAM LOADING SECTION

BM901

TO DVD BOARD (7/8) CN402 (Page 39)

6-29.

PRINTED WIRING BOARD LOADING SECTION

TO DVD BOARD CN402 (Page 31)

BM901

55

HCD-S500

6-30.IC102

IC BLOCK DIAGRAMSIMIC6001BT-D (DVD BOARD)

IC606

LC89056W (DVD BOARD)VF/P3/C3 F2/P2/C2 F1/P1/C1 F0/P0/C0 CSFLAG DI DO ERROR BPSYNC AUTO DGND DVDD

36 35 34 33 32 31

30

29 28 27 26 25

CE 37 CL 38 MICROCOMPUTER INTERFACE XSEL 39 SAMPLING FREQUENCY

C BIT DETECT

PA/PB DETECT

24 AUDIO 23 EMPHA

LOCK DETECT MODE SELECT

CLOCK

MODE0 MODE1 DGND DVDD DOSEL0 DOSEL1

40 41 42 43 44 45

DATA DEMODULATOR

TIMING

22 21 20 19 18 17 16 15 14 13

XIN XOUT XMCK DVDD DGND XSTATE DATAO LRCK BCK CKOUT

CKSEL0 46 CKSEL1 47 XMODE 48 SYSTEM RESET INPUT CIRCUIT PLL

1DISEL

2 3DOUT DINO

4DINI

5DIN2

6 7DGND DVDD

8 9 10R VIN LPF

11 12AVDD AGND

IC608

PCM1748 (DVD BOARD)System Clock System Clock Manager 16 MCLK

BCK 1 DATA 2 LRCK 3

Serial Input I/F

8x Oversampling Digital Filter with Function Controller Function Control I/F Enhanced Multi-Level Deita-Sigma Modurator Zero Detect DAC DAC 15 LAT 14 CLK 13 DATA 12 DZFL 11 DZFR

DGND 4 VDD 5 VCC 6

Power Supply

LOUT 7

Output Amp and Low-Pass Filter

Output Amp and Low-Pass Filter 10 VCOM 9 AGND

ROUT 8

56

HCD-S500

IC802

MSM9202-05GS-KDR1 (FP-1030 BOARD)Timing Generator 2 Duty Control Digit Control 8bit Shift Register Timing Generator 1 64 VDD

P1 1 P2 2

Port Driver

Control Circuit

63 DAT 62 CLK 61 CS

60 RST Command Decoder Read Address Counter Write Address Counter Oscillator 59 OSC1 58 OSC0

AD2 3 AD1 4

AD Driver

ADROM 16wX2b

Address Selector

57 GND 56 VFL

S1 5 S28 32

CGROM 8wX35b Segment Driver CGROM 248wX35b DCROM 16wX8b

Grid Driver

55 G16 40 G1

39 S35 33 S29

IC600

MC14052BDR2 (I/O BOARD)

IC604RCLK

BU1924F-E2 (I/O BOARD)VDD2 NC XO VSS2 T1 T2 XI

16

15

14

13

12 11 10

9

CLOCK PLL 57kHz RDS/ARI PLL 1187.5Hz

DIGITAL

TEST

COMPARATOR

DEFFERENTIAL DECODER

ANTI-ALIASING FILTER

1QUAL

2RDAT

3VREF

4MUX

ANALOG

BIPHASE DECODER

8th SWITCHED CAPACITOR FILTER

5VDD1

6VSS1

7VSS3

8CMP

57

HCD-S500

IC001

SP3728AC (RF-240 BOARD)ATON ATOP SIGO MEV VNA BYP FNN VPA FNP TPA V33 DIN DIP AIN AIP RX

64

63

62

61

60

59

58

57

56

55

54

53

52

51

50

49

FULL WAVE RECTIFIER RFIP 1 ATT RFIN 2 BOTTOM ENV CP 3GCA

AGC CHARGE PUMP 48 SDEN

PROGRAMABLE EQ FILTER 47 SCLK

BEL

46 SWD

WIN

4

GCA GCA

GCA

LPF

45 SRD

WPP

5

GCA

LPF SEL

44 MON

CN

6

43 TPH

A2

7GCA

42 FE

B2

8

GCA GCA

41 TE

C2

9

GCA

WABLE BPF 40 TZIN MON SEL

D2

10

39 VCI

D

11GCA GCA GCA GCA

38 DFT EQ EQ EQ EQ PHASE DETECTOR VC 36 PI PHASE DETECTOR MUX LPF 37 TZC

C

12

B

13

A

14 SERIAL PORT REGISTER MUX APC LD SEL MUX PEAK/ BOTTOM HOLD

35 PII

E

15

34 BYP2

F

16

33 MIRR

17G

18H

19VC

20VPB

21DVDPD

22CDPD

23VNB

24LDSELO

25DVDLD

26CDLD

27LDON

28MEVO

29MIN

30MP

31MB

32MLPF

58

HCD-S500

IC901

STR-F6676 (POWER BOARD)

LATCH COMP.1

O.V.P.

START

T.S.D.

REG.

OSC

DRIVE

ICONST

COMP.2

1 FB/OCP

2 S

3 D

4 VCC

5 GND

59

HCD-S500

6-31. IC103 Pin No. 1 to 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54

IC PIN FUNCTION DESCRIPTIONMB91307APFV-G-BND-E1 (SYSTEM CONTROL) (DVD BOARD) Pin Name HA17 - 21 HA22 WP TRM/XKRCS AVCC AVRH AVSS AN0 AN1 AN2 AN3 INT0 INT1 INT2 INT3 INT4 INT5 INT6 INT7 VCC SI0 SO0 SC0 SI1 SO1 SC1 SI2 SO2 SC2 VSS XRST XARPRST RGBSEL/MICMUTE SDA SCL TRM+/XKRRST EUROV/Y/CLPSW1 DISCEXT/CLPSW0 MD0 MD1 MD2 DREQ0 DACK0 XDRVMUTE DREQ1 DACK1 XIFCS VSS X1 X0 I/O O O O O I I I I I I I I I I O I O O I O O I O O O O I/O O O I O O I O O Address signal output Address signal output (not used) I2C EEPROM write protect signal output Chip select signal output to IC801(CXD2752R) Analog power supply A/D converter reference voltage supply Analog ground Region setting input Model setting input Destination setting input Not used (pull-up) Interrupt signal input from IC503(AV Decoder) Interrupt signal input from IC302(CXD9635R/ARP) Interrupt signal input from IC302(CXD9635R/SDSP) FGA interrupt signal input Interrupt signal input from IC901(CPU) Interrupt signal input from IC801(CXD2752R) Soft mute control signal output to IC801(CXD2752R) Not used Power supply Serial data input from IC901(CPU) Serial data output to IC901(CPU) Serial clock output to IC901(CPU) Serial data input from IC801(CXD2752R) Serial data output to IC801(CXD2752R) Serial clock output to IC801(CXD2752R) RS-232C data input for debugging RS-232C data output for debugging RS-232C clock input or output for debugging Ground System reset signal output Reset signal output to IC302(CXD9635R/ARP) Not used I2C data input or output I2C clock output Data request selection signal output (DVD : L, SACD : H) Not used Not used Operation mode setting (connected to Vcc) Operation mode setting (connected to Ground) Operation mode setting (connected to Ground) DMA-REQ1 signal input DMA-ACK1 signal output Drive mute control signal output to IC401 DMA-REQ0 signal input DMA-ACK0 signal output Chip select signal output to IC901(CPU) Ground Clock (oscillator) output Clock (oscillator) input Description

60

HCD-S500

Pin No. 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 to 100 101 102 to 109 110 111 to 118 119 120

Pin Name VCC CKSW1 OCSW1 CS0X CS1X CS2X CS3X CS4X CS5X C CS6X CS7X XWAIT BGRNTX BRQ XRD XWRH XWRL XMIX HSTX VSS XFRRST CPUCK OCSW2 XDACK VESCS/X39CS 48/44.1K WIDE MAMUTE XLDON HD0 -15 VSS HA0 - 7 VCC HA8 - 15 VSS HA16

I/O I I O O O O O O I I I O O O I O I O O I O I/O O O O Power supply Chucking switch (Tray SW1) signal input Open/Close switch (Tray SW2) signal input Chip select signal output to external ROM Not used Chip select signal output to AVD SDRAM Chip select signal output to AVD R-BUS

Description

Chip select signal output to IC302(CXD8635R/ARP) Chip select signal output to IC302(CXD8635R/SDSP) Terminal for built-in regulator bypass capacitor FGA CS output Not used external WAIT signal input External bus open aclnowledge signal input (pull-up) External bus open request signal input External bus read enable signal output Write signal output for upper byte Write signal output for lower byte Not used Not used (pull-up) Ground Reset signal input CPU clock output Tray switch signal input Not used (pull-up) Not used (pull-up) PLL IC control signal output Video wide offset control signal output IFOK signal input from IC901(CPU) Laser diode mute control signal output External data bus bits 0 - 15 Ground Address signal output Power supply Address signal output Ground Address signal output

61

HCD-S500

IC302 Pin No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50

CXD9635R (SERVO DSP) (DVD BOARD) Pin Name VSS D0 D1 D2 D3 D4 D5 D6 D7 VDD 3.3V A0 A1 A2 A3 A4 VDD A5 A6 A7 VDD 1.8V XINT HINT XCS HCS XWAT VSS MA0 MA1 MA2 MA3 MA4 MA5 MA6 MA7 MA8 MA9 VDD 3.3V XMWR XCAS VSS XRAS XOE VDD1 1.8V MD0 MD1 MD2 MD3 MD4 MD5 MD6 I/O I/O I/O I/O I/O I/O I/O I/O I/O I I I I I I I I O O I I O O O O O O O O O O O O O O O I/O I/O I/O I/O I/O I/O I/O DRAM data Digital power supply 3.3V DRAM write enable DRAM CAS Digital Ground DRAM RAS DRAM output enable Digital power supply 1.8V DRAM address Digital power supply 1.8V Interrupt Host interrupt(DSP) Tip select Host servo tip select Wait Digital Ground CPU address Digital Ground CPU address Digital power supply 3.3V CPU data Digital Ground Description

62

HCD-S500

Pin No. 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100

Pin Name MD7 VSS MD8 MD9 MD10 MD11 MD12 MD13 MD14 MD15 VDD 3.3V DATA BCLK VSS LRCK DOUT VDD 1.8V SDCK XSHD XSRQ XSAK SDEF SD0 SD1 SD2 SD3 VSS SD4 SD5 SD6 SD7 VDD 3.3V MNT0 MNT1 MNT2 MNT3 MNT4 MNT5 MNT6 MNT7 ESTB VDD 1.8V RFD VSS PLCKO ADO0 ADO1 ADO2 ADO3 ADO4

I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O O O O O O O I/O O O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O O I/O O O O O O O ADC output Error storbe Digital power supply 1.8V RF digital data in/out Digital Ground PLCK output Monitor bus Digital power supply 3.3V SD bus data Digital Ground SD bus data Digital power supply 3.3V CDDA data CDDA bit clock Digital Ground CDDA LR clock Digital out Digital power supply 1.8V SD bus clock SD bus header SD bus REQ SD bus ACK SD bus error flag DRAM data DRAM data Digital Ground

Description

63

HCD-S500

Pin No. 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150

Pin Name ADO5 ADO6 ADO7 VSS VSSA4 VCO R1 R2 VDDA4 3.3V VSSA3 INP INM FR3 FR2 FR1 Y VDDA3 3.3V VREF BIAS VDDA2 3.3V VSSA2 AOUT IREF VSSD2 VDDD2 3.3V VRT VDDA1 3.3V RFIN1 AIN VSSA1 RFIN1 VRB VSSD1 VDDD1 3.3V ADC0 ADC1 ADC2 VDDA0 3.3V ADC3 ADC4 VSSA0 ADC5 ADC6 ADC7 VDDD0 3.3V VSSD0 VRBA VSSA0 TESTAA VDDA0 3.3V

I/O O O O I I I I I I I I O I I O I I I I I I I I I I I I I I I O ADC digital power supply(DSP) ADC digital ground DSP ADC reference Analog ground(ADC) ASW output ADC analog power supply(DSP) ADC input ASW analog power supply ADC input ASW analog ground ADC input Digital Ground Analog Ground VCO control input VCO outside resistance 1 VCO outside resistance 2 Analog power supply Analog Ground OP amp positive input OP amp negative input Feedback resistance 3 Feedback resistance 2 Feedback resistance 1 OP amp output Analog power supply DAC reference voltage DAC bias pin Analog power supply Analog Ground DAC output Reference current of DAC Digital Ground(DAC) Digital power supply(DAC) ADC reference Analog power supply RF input RF input Analog Ground RF input ADC reference Digital Ground(ADC) Digital power supply(ADC) ADC output

Description

64

HCD-S500

Pin No. 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200

Pin Name VRTA VSS TESTK0 TESTK1 TESTK2 XDSPRST XARPRST VSS MDS0 MON MDP0 DFCT JITPWM LOCK VDD1 1.8V GIO0/INT2 GIO1/INT3 GIO2/INT4 GIO3/INT5 VDD 3.3V GIO4/PGREF GIO5/PGIN GIO6/SDI GIO7/SDO GIO8/SCK GIO9/FGREF GIO10/FGIN GIO11/TMC2 GIO12 GIO13 VSS CLKIN VSSA5 VDDA5 1.8V DFCTI VSS MCKI VDD 1.8V SCKI VSS TRST TMS TDI TCK TDO TZC MIRR PWM0 PWM1 PWM2

I/O I I I I I I O O O I/O O O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I I I I I I I I O I I O O O PWM output TZC input MIRR input JTAG Boundary scan Digital power supply 3.3V GIO/PGREF input GIO/PGIN input GIO/serial data in GIO/serial data out GIO/serial clock GIO/FGREF input GIO/FGIN input GIO/Timer 2 clock input GIO(input and output) Digital Ground Clock input Analog Ground Analog power supply Defect input Digital Ground Clock for ECC 33MHz Digital power supply 1.8V System clock Digital Ground GIO/external interruption DSP reset Reset Digital Ground CLV speed error Motor on CLV phase error Defect detection output Jitter PWM output EFM lock detection Digital power supply 1.8V Test terminal L ADC reference Digital Ground

Description

65

HCD-S500

Pin No. 201 202 203 204 205 206 207 208

Pin Name VDD 3.3V PDM0 PDM1 PDM2 PDM3 VSS XWR XRD

I/O O O O O I I Digital Ground CPU light CPU lead PDM output Digital power supply 3.3V

Description

66

HCD-S500

IC801 Pin No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 to 25 26 27 28 29 30 31 32 to 34 35 36 37 38 to 41 42 43, 44 45 46, 47 48 49 50 51, 52 53 54 55, 56 57 58 59 60 61 62 63 64 65 66

CXD2752R (PLAYBACK SIGNAL PROCESSOR) (DVD BOARD) Pin Name VSCA0 XMSLAT MSCK MSDATI VDCA0 MSDATO MSREADY XMSDOE XRST SMUTE MCKI VSIOA0 EXCKO1 EXCKO2 LRCK F75HZ VDIOA0 MNT0 - 7 TCK TDI VSCA1 TDO TMS TRST TEST1 - 3 VDCA1 UBIT XBIT SUPDT0 - 3 VSIOA1 SUPDT4 - 5 VDIOA1 SUPDT6 - 7 SUPEN VSCA2 NC TEST4 - 5 NC VDCA2 NC BCKASL VXDSD0 BCKAI BCKAO PHREFI PHREFO ZDFL DSAL ZDFR DSAR I/O I I I O O O I I I O O O O O I I O I I I O O O O O O O I O O I I O I O O O O O Ground Latch signal input for micom serial communication Shift clock input for micom serial communication Data input for micom serial communication Power supply Data output for micom serial communication Output ready flag output for micom serial communication Output enable signal output for micom serial communication Reset signal input Soft mute signal input (H:soft mute, L:off) Master clock input (768Fs 33.8688MHz) Ground for I/O External clock output 1 External clock output 2 (not used) Clock output (1Fs 44.1kHz)(not used) Frame signal output Power supply for I/O Monitor signal output (not used) Test clock input (connected to ground) Input terminal for test Ground Output terminal for test (open) Input terminal for test (open) Reset terminal for test (open) Input terminal for test (connected to ground) Power supply Output terminal for test (open) DST monitor terminal (open) Supplementary data output (open) Ground for I/O Supplementary data output (open) Power supply for I/O Supplementary data output (open) Supplementary data acknoledge output (open) Ground Output terminal for test (open) Input terminal for test (connected to ground) Output terminal for test (open) Power supply Output terminal for test (open) Bit clock I/O selection signal input for DSD data output (L:slave, H:master) Ground for DSD data output Bit clock input for DSD data output (open) Bit clock output for DSD data output Phase reference signal input for DSD signal phase modulation (open) Phase reference signal output for DSD signal phase modulation (open) Lch zero data detection flag signal output (open) Lch DSD data output Rch zero data detection flag signal output (open) Rch DSD data output Description

67

HCD-S500

Pin No. 67 68 69 70 71 72 73 74 75 76 77 78, 79 80 81, 82 83 84, 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 to 105 106 107 to 109 110 111 to 114 115 116 117 to 120 121 122 123 124 to 125 126 127 128 to 129 130 131 to 134 135 136 to 139

Pin Name VDDSD0 ZDFC DSAC ZDFLFE DSALFE VSDSD1 ZDFLS DSALS ZDFRS DSARS VDDSD1 IOUT0 - 1 VSCB0 IOUT2 - 3 VDCB0 IOUT4 -5 VSIOB0 IANCO IFULL IEMPTY VDIOB0 IFRM IOUTE IBCK VSCB1 IERR IANCI IPLAN IHOLD VDCB1 IVLD IDIN0 - 4 VSIOB1 IDIN5 -7 VDIOB1 WAD0 - 3 TESTI VSCB2 WAD4 - 7 VDCB2 WRFD WCK WAVDD0 - 1 WARFI WAVRB WAVSS1 - 0 VSIOA2 DQ7 - 4 VDIOA2 DQ3 - 0

I/O O O O O O O O O O O O O I I O O O I I I O I I I I I I I I I I/O I/O Power supply for DSD data output

Description

Cch zero data detection flag signal output (open) Cch DSD data output LFEch zero data detection flag signal output (open) LFEch DSD data output Ground for DSD data output LSch zero data detection flag signal output (open) LSch DSD data output RSch zero data detection flag signal output (open) RSch DSD data output Power supply for DSD data output Output terminal for test (open) Ground Output terminal for test (open) Power supply Output terminal for test (open) Ground for I/O Output terminal for test (open) Input teminal for test (connected to ground) Input te