6
CHEPPALI VENKATA RAMESH E-mail: [email protected] Mobile No: +91-7710098307 OBJECTIVE Aspiring to become an oil and gas professional in an organization where I will get exposure and can effectively contribute my best using my knowledge and skills to achieve organizational goals. SUMMARY OF QUALIFICATIONS Completed M.Tech in Process Engineering from University of Petroleum and Energy Studies with 78%. B.Tech (Chemical Engineering) from Sri Venkateswara University in 2003 with 61% Intermediate (MPC) From Board of Intermediate Education in 1998 with 87.5% SSC From Secondary School Education in 1996 with 84% PROFESSIONAL SUMMARY 5+ years of Experience in Oil and Gas Industries.. Preparation of Line Designation Table, Back checking of P&ID S etc for various projects.

Documentcv

Embed Size (px)

DESCRIPTION

kjk

Citation preview

ADDRESS 1 ADDRESS 2 ADDRESS 3

Cheppali venkata ramesh E-mail: [email protected] Mobile No: +91-7710098307objectiveAspiring to become an oil and gas professional in an organization where I will get exposure and can effectively contribute my best using my knowledge and skills to achieve organizational goals.Summary of qualifications Completed M.Tech in Process Engineering from University of Petroleum and Energy Studies with 78%. B.Tech (Chemical Engineering) from Sri Venkateswara University in 2003 with 61% Intermediate (MPC) From Board of Intermediate Education in 1998 with 87.5%

SSC From Secondary School Education in 1996 with 84%PROFESSIONAL SUMMARY5+ years of Experience in Oil and Gas Industries.. Preparation of Line Designation Table, Back checking of P&ID S etc for various projects. Design of Control valves, Storage Tanks and preparation of Interface Tables. Pump hydraulics calculations and data sheets of Control valves,pumps,Exchangers ,Tanks etc Material and Energy Balance Calculations, Heat loads calculations, Optimization Calculations etc Line sizing calculations, Tie in packages, Design Development Documents for various projects.

Updating and reviewing of P&IDs for various projects.

Design of Absorbers, Strippers, Heat Exchangers, for various projects.Employment Working as a Associate Process Specialist at FLUOR DANIEL from May 2013 to TILL DATE Worked as a Process Engineer at CCDCINDIA from April 2011 to April 2013

Worked as a Process Engineer at SAIPEM TRUINE ENGINEERING from May 2010 to April 2011 Worked as a Junior Engineer for CREST ENGINEERING from Feb 2005 to Feb 2007PROJECTS SUMMARYProject #1Title :SHELL-QATAR PETROLEUM PROJECT Client

:SHELLDuration :May 2013 to March 2014Technologies :ASPEN, HYSYS, PALSE, VIESA,Description :The project is to design and develop a Petrochemical project in Ras Laffatin, Qatar.Its a feed Lump sum project compromising three units.1. MEG Unit with shell as Licensor

2. OXO Unit with Mitsubishi as licensor

3. LAO unit with shell as a licensor

4. UTILITIES Studied the PFD and P&IDs of Project

Control valve sizing Pump Hydraulic calculations Design of Tanks Preparing Interface tables Updating control valve,tank,exchanger data sheetsProject #2Title :Gas Sweetening Unit Client

:Vinati Organics LimitedDuration :October 2011 to Till Date

Technologies :ASPEN, HYSYS

Description :The project is to design and develop a Gas sweetening Unit. Gas sweetening plant is a vital operating unit, where the sour contents (H2S and CO2) of the feed gas are removed to make it sweet for processing. In the Gas Sweetening process, the sour contents present in the feed natural gas are removed by chemical absorption technique with amines. The feed gas for train-3 is HP gas (780 psig); the sour content H2S and CO2 would be at 2.2% and 4.0% respectively. And the sweetened gas (per design) would have 5 ppm H2S and 50 ppm CO2. The H2S and CO2 gases present in feed natural gas are normally soluble in water to form acidic solutions, the gas are counter contacted with amines. Later amines with acidic gases are stripped removing 99% of acid compounds.

Heat and Mass Balance Calculations Studied the PFD and P&IDs of Project

Design of Heat Exchanger Design of Washer,stripperProject #3Title :Gas Dehydration Unit Client

:Aditya Birla groupDuration :May 2011 to September 2011Technologies :ASPEN, HYSYS

Description :Glycol dehydration unit is to remove water from natural gas and natural gas liquids. When produced from a reservoir natural gas usually contains a large amount of water and is typically completely saturated or at the water dew point. This water can cause several problems for downstream processes and equipment. At low temperatures the water can either freeze in piping or, as is more commonly the case, form hydrates with CO2 and hydrocarbons (mainly methane hydrates. Lean, water-free glycol (purity >99%) is fed to the top of an absorber (also known as a "glycol contactor") where it is contacted with the wet natural gas stream. The glycol removes water from the natural gas by physical absorption and is carried out the bottom of the column.Responsibilities :

Co-ordinating a multi-discipline team to ensure timely and quality delivery of Project Heat and Mass Balance Calculations Studied the PFD and P&IDs of Project

Design of Absorber and stripper for Dehydration unit.Project #4 Title :Revamping of ONGC Offshore Project SagarLakshmi Client

:ONGC

Duration :January2011 to April 2011Technologies :ASPEN, HYSYS

Description :This is a case Study to Install an Additional Separator at ONGC Offshore Platform SAGARLAKSHMI. Along With the Existing Separators an Additional Separator has to be placed so as to Increase the Production. Different cases have been developed using HYSYS and all the cases have been sent for client Final Review.Responsibilities :

Studied the PFD and P&IDs of ONGC Offshore Platform.

Design of Separator

Simulation using HYSYS.

Calculated the Mass balances

ACHIEVEMENTS

Achieved World record in Completing Qatar Petroleum Feed project for Shell. Completed All the Off sites and utilities for Reliance in the Prescribed Time Successfully completed Revamping of ONGC offshore Project

Optimize assets while Calculating line sizes, Hydraulics etc.TECHNICAL SKILLS Operating systems : Windows-98/NT/2000,2003,server

Simulation softwares : Aspen,Hysys,ProII

Design Softwares : Visio,Flowsheet

Languages : C, C++, C#. NET,VB.NETRDBMS : SQL-Server2000, ORACLE 7.7,9I

Microsoft technologies : ASP.NET, VB.NET, C#, ADO.NETPERSONAL DETAILS Date of Birth : 1 July 1981Nationality : IndianPass Port No : K1042129

Date of Issue : 05/02/2013

Date of Expiry : 04/02/2023 Place of Issue : Chennai

Languages known : English, Hindi and TeluguPermanent Address : C.V.Ramesh Babu

DOOR NO:D-30,PMF QUARTERS, Milk Products Factory, Proddatur,

Cuddapah District,

ANDHRAPRADESH,INDIA 516360

CONTACT NO 08500224625REFERENCEs1. Mr. Sreedhar Kambham, Project Co-ordinator, AFCONS, (+918767099796).

2. Sreenivasulu (Piping Engineer) from ccdc india (+919840959400)