Customs Tariff Concessions 7201_to_7221

Tariff Description ===========================================================================

Item 50 applies unless otherwise stated.

7201.10.00 PIG IRON, comprising ALL of the following: (a) carbon, with a composition less than 5%; (b) sulphur; (c) silicon; (d) phosphorus; (e) manganese Op. 02.11.1999 Dec. 07.01.2000 - TC 9908323 7207.11.00 BILLETS, square, semi-finished non-alloy steel, having ALL of the following: (a) thickness and width NOT less than 130 mm X 130 mm; (b) length NOT less than 11 800 mm and NOT greater than 12 200 mm; (c) chemical composition by weight of ALL of the following: (i) carbon 0.13 % - 0.17%; (ii) manganese 0.35% - 0.55%; (iii) sulphur 0.035 % maximum; (iv) chromium 0.2 % maximum; (v) copper 0.3% maximum; (vi) phosphorous 0.035% maximum; (vii) silicon 0.14% - 0.24% Op. 27.06.2008 Dec. 19.09.2008 - TC 0815096 7207.19.00 STEEL BLOOMS, ROUND, NON ALLOY Op. 02.11.2007 Dec. 30.01.2008 - TC 0718813 7207.19.00 BILLETS, leaded, hot rolled Op. 11.09.2001 Dec. 07.12.2001 - TC 0108047 7207.20.00 STEEL BAR, round cornered square section, to Military Standard 10520D, ultrasonically tested in accordance with ASTME-381, having the following dimensions: (a) sides 100 mm x 100 mm (+ or - 2.0 mm); (b) radius 15 mm maximum Op. 13.06.1997 Dec. 22.08.1997 - TC 9705183 7208.51.00 PLATE OR SHEET, steel, quenched and tempered, having a thickness exceeding 101.4 mm Op. 01.07.1996 Dec. 07.06.1996 - TC 9605765 7208.51.00 PLATE OR SHEET, steel, having EITHER of the following: (a) a thickness exceeding 104 mm; (b) a width exceeding 3.3 m, but NOT including the following grades or specifications: (1) Grade 250 (including modified analysis) having: (i) a thickness of 110 mm to 150 mm; and (ii) a width of 1 600 mm to 2 400 mm; (2) Grade XK1016 (including modified analysis) having: (i) a thickness of 160 mm to 250 mm; and (ii) a width of 1 600 mm to 2 400 mm For the purposes of this order, all measurements have a tolerance of + OR - 5% Op. 12.03.1997 Dec. 13.06.1997 - TC 9702134 7208.52.00 STEEL SHEETS, grade Tu15D3, having ALL of the following: (a) thickness NOT less than 7.5 mm and NOT greater than 8.5 mm; (b) width NOT less than 1 950 mm and NOT greater than 2 050 mm; (c) length NOT less than 5 750 mm and NOT greater than 5 850 mm Op. 23.09.2005 Dec. 16.12.2005 - TC 0512722



7208.53.00 STEEL SHEETS, grade Tu15D3, having ALL of the following: (a) thickness NOT greater than 3.25 mm; (b) width NOT less than 1 475 mm and NOT greater than 1 525 mm; (c) length NOT less than 5 750 mm and NOT greater than 5 850 mm Op. 23.09.2005 Dec. 16.12.2005 - TC 0512721 7208.90.00 PLATES, CARBON STEEL, hot rolled, ASME SA 516 grade 60 Normalised, modified for Sour Service, complying with NACE MR0175 OR ISO 15 516-2:2003 (E) Annex A, clause A.2.1.2, and EN1024:2004 3.1 Standards, vacuum degassed and normalised, having ANY of the following dimensions: (a) 1965 x 10400 x 77mm (b) 2600 x 5200 x 44mm (c) 2200 x 4000 x 32mm (d) 2800 x 5400 x 25mm (e) 2800 x 5300 x 20mm (f) 2800 x 5300 x 16mm For the purposes of this Order, tolerances of + or - 1% are allowable for specifcations (a) through (f) Op. 26.07.2007 Dec. 02.01.2008 - TC 0712139 7209.27 SHEET OR STRIP, high carbon steel, round edged, stretcher levelled, being conveyor banding, having ALL of the following: (a) a width of NOT less than 600 mm; (b) a thickness of NOT less than 0.5 mm but NOT exceeding 1 mm; (c) a minimum yield strength of 800 MPa; (d) a camber tolerance of 10 mm in 100 m Op. 01.07.1996 Dec. 01.07.1996 - TC 9605650 7210.30.00 STEEL, flat rolled non-alloy, electrolytically coated with zinc, having ALL of the following features; (a) a thickness of 2.39mm or more; (b) a width NOT less than 1219mm and NOT greater than 1249 mm; (b) to specification JIS G3313 SECC or SEHC Op. 01.07.1996 Dec. 21.06.1996 - TC 9607869 7210.30.00 STEEL, flat rolled, non-alloy, zinc or zinc-nickel or zinc-iron coated, electroplated, having ANY of the following: (a) differential coating mass on each side; (b) equal coating mass for zinc-nickel coating only on each side of NOT greater than 40 grams per square metre; (c) additional iron base alloy electroplated outer coating; (d) an organic overlay on EITHER one OR both sides; (e) width exceeding 1 525 mm; (f) a minimum ultimate tensile strength of 340 MPa Op. 09.10.1996 Dec. 20.12.1996 - TC 9611358 7210.49.00 STEEL, COIL, hot dip zinc coated, complying with Japanese Industrial Standard JIS G 3302:2007, having ALL of the following: (a) yield strength NOT less than 275 N/mm2 and NOT greater than 380 N/mm2; (b) tensile strength NOT less than 440 N/mm2; (c) elongation NOT less than 29% and NOT greater than 41%; (d) coating mass NOT less than 45 g/m2 and NOT greater than 65 g/m2; (e) thickness NOT less than 1.14 mm and NOT greater than 1.26 mm; (f) width NOT less than 1 590 mm and NOT greater than 1 605 mm Op. 21.10.2009 Dec. 08.01.2010 - TC 0939596



7210.49.00 STEEL, flat rolled non alloy, hot dipped galvannealed, having ANY of the following: (a) differential coating mass on each side; (b) additional iron base alloy electroplated outer coatings; (c) width exceeding 1 525 mm; (d) a minimum ultimate tensile strength of 340 MPa Op. 12.11.1996 Dec. 20.01.1997 - TC 9612218 7210.50.00 TIN FREE STEEL, flat rolled, in coils, chromium plated, having ALL of the following: (a) width NOT less than 750 mm and NOT greater than 1 000 mm; (b) thickness NOT greater 0.30 mm; (c) temper designation of 61 to 76 (both inclusive) in accordance with Rockwell hardness 30 T range Op. 26.11.2009 Dec. 26.02.2010 - TC 0944971 7210.50.00 TIN FREE STEEL, flat rolled, in coils, chromium plated, having ALL of the following: (a) width of 830 mm or greater but NOT exceeding 850 mm; (b) thickness NOT exceeding 0.18 mm; (c) temper designation of 70-76 (both inclusive) in accordance with Rockwell hardness 30 T range Op. 14.12.2001 Dec. 08.03.2002 - TC 0111311 7210.69.00 STEEL SHEET, ALUMINIUM SILICON ALLOY COATED, whether or not in coil, having ALL of the following: (a) width 630 mm, 699 mm, 780 mm, 790 mm, 810 mm, 900 mm, 914 mm, 930 mm, 990 mm, 1 000 mm, 1 025 mm, 1 030 mm, 1 035 mm, 1 100 mm, 1 120 mm, 1 146 mm, 1 160 mm, 1 165 mm, 1 170 mm, 1 200 mm, 1 219 mm, 1 220 mm, 1 250 mm; (b) thickness 0.55 mm, 0.60 mm, 0.72 mm, 0.75 mm, 0.80 mm, 0.90mm, 0.96 mm, 1.00 mm, 1.15 mm, 1.20 mm, 1.50 mm, 1.55 mm, 1.60 mm, 1.90 mm or 2.00 mm; (c) coating consisting of NOT less than 88% aluminium and balance silicon; (d) coating weight NOT less than 20 gsm and NOT greater than 90 gsm; (e) conforming to EITHER of the following: (i) American Society of Testing and Materials Standards A 463, having ANY combination of the following: (i) coating symbol T1-25 or T1-40; (ii) quality CS or FS or DDS or EDDS; (ii) Japanese Industrial Standard JIS G 3314, having ANY combination of the following: (i) coating symbol 40 or 60 or 80; (ii) quality SA1C or SA1D or SA1E For the purposes of this order tolerances allowable on widths and thicknesses are: (a) widths + or - 2 mm; (b) thicknesses + or - 0.2 mm Op. 19.11.2009 Dec. 05.02.2010 - TC 0943744 7210.69.00 SHEET, STEEL, aluminium coated to American Society of Testing and Materials A 463 (ASTM A 463) having ANY combination of the following: (a) coating: (i) T1-25; (ii) T1 - 40 (b) quality: (i) CS; (ii) DDS Op. 07.07.2008 Dec. 26.09.2008 - TC 0816281



7210.69.00 STEEL, aluminium coated, flat rolled, coil, conforming to ASTM A463 OR JIS G 3314, chromated OR non chromated, having ANY combination of the following characteristics: (a) coating: (i) T125; (ii) T140; (b) quality: (i) CQ; (ii) DQ; (iii) DDQ Op. 10.11.1997 Dec. 16.01.1998 - TC 9709961 7210.70.00 STEEL, hot-dip zinc-coated, high polymer prepainted, complying with Japan Industrial Standard G3312/CGC400-20 Z12 (JIS G3312/CGC400-20 Z12) AND European Union Directive 2002/95/EC on the Restriction of the Use of Certain Hazardous Substances in Electrical and Electronic Equipment (RoHS), having ALL of the following: (a) One side surface colour (painted) either white or grey; (b) Coating adhering to polyurethane on one side; (c) Specular gloss level at 60 degrees NOT less than 60 units and NOT more than 90 units; (d) Distinction of image (DOI) NOT less than 60 units; (e) Zinc coating mass of z12 or less; (f) Surface having ALL of the following: i) inclusions NOT greater than 1 mm over 1 square metre and having proximity NOT less than 400 mm; ii) dents NOT greater than 1 mm over 1 square metre and having proximity NOT less than 400 mm; iii) leveller bite NOT greater than 20 mm (g) In ANY of the following sizes ; width 660 mm and thickness 0.45 mm width 710 mm and thickness 0.45 mm width 722 mm and thickness 0.45 mm width 883 mm and thickness 0.45 mm width 883 mm and thickness 0.5 mm width 708 mm and thickness 0.5 mm width 780 mm and thickness 0.5 mm width 780 mm and thickness 0.45 mm width 515 mm and thickness 0.5 mm width 605 mm and thickness 0.5 mm For the purposes of this Order, tolerances allowable for specification (g) are: (a) width +/or - 2 mm (b) thickness +/or - 0.03 mm Op. 17.04.2009 Dec. 15.06.2009 - TC 0919901 7210.70.00 SHEET, COMPOSITE, galvanized steel laminated with polyvinyl chloride, having BOTH of the following: (a) steel thickness NOT less than 0.6 mm; (b) polyvinyl chloride laminate thickness NOT less than 0.8 mm Op. 01.08.2005 Dec. 21.10.2005 - TC 0510003



7210.70.00 SHEETS AND/OR STRIPS, STEEL, NON-ORIENTATED ELECTRICAL, as described in ANY of the following international standards: (a) Japanese Industrial Standard C 2552; (b) American Society for Testing and Materials Standard A 677-05; (c) European Standard EN 10106 Op. 23.03.2006 Dec. 16.06.2006 - TC 0605624 7210.70.00 STEEL, high polymer polyester coated, complying with Japan Industrial Standard G3312/SGCD1 (JIS G3312/SGCD1) AND European Union Directive 2002/95/EC on the Restriction of the Use of Certain Hazardous Substances in Electrical and Electronic Equipment (RoHS), having ALL of the following: (a) epoxy reverse coating adhering to polyurethane; (b) specular gloss level NOT less than 80 units at 60 degrees; (c) distinction of image NOT less than 60 units; (d) surface having ALL of the following: (i) inclusions NOT greater than 0.2 mm over 1 square metre and having proximity NOT less than 400 mm; (ii) dents NOT greater than 0.3 mm over 1 square metre and having proximity NOT less than 400 mm; (iii) leveller bite NOT greater than 20 mm; (e) in ANY of the following sizes: (i) width 607 mm and gauge 0.5 mm; (ii) width 672 mm and gauge 0.5 mm; (iii) width 729 mm and gauge 0.5 mm; (iv) width 732 mm and gauge 0.5 mm; (v) width 774 mm and gauge 0.5 mm; (vi) width 824 mm and gauge 0.5 mm; (vii) width 924 mm and gauge 0.5 mm; For the purposes of this order, tolerances allowable for specification (e) are: (a) width +2 mm; (b) gauge + or - 0.02 mm Op. 26.09.2006 Dec. 05.02.2007 - TC 0615052 7210.70.00 STEEL, TIN FREE, laminated on one side with polypropylene and on the other side with polyethylene terephthalate Op. 26.06.1998 Dec. 11.09.1998 - TC 9805588 7210.90 PLATES OR SHEETS, steel, clad with titanium Op. 30.04.1987 Dec. 24.09.1987 - TC 8733390 7210.90.00 SHEETS AND/OR STRIPS, STEEL, NON-ORIENTATED ELECTRICAL, as described in ANY of the following international standards: (a) Japanese Industrial Standard C 2552; (b) American Society for Testing and Materials Standard A 677-05; (c) European Standard EN 10106 Op. 23.03.2006 Dec. 16.06.2006 - TC 0605625 7210.90.00 CERAMIC STEEL, being two layers of enamel fused onto high grade steel Op. 14.11.1994 Dec. 07.03.1995 - TC 9408919 7211.14.00 STEEL, flat bar, square OR round edge, equivalent to Australian and New Zealand Standard 3679.1.250 (AS/NZS 3679.1.250) AND Australian and New Zealand Standard 3679.1.300 (AS/NZS 3679.1.300) AND Australian and New Zealand Standard 3679 9.1.350 (NZS 3679.1.350) OR mild steel, having BOTH of the following: (a) width NOT less than 98 mm and NOT greater than 102 mm; (b) thickness NOT less than 48 mm and NOT greater than 52 mm Op. 06.10.2009 Dec. 19.02.2010 - TC 0937812



7211.19 HOOP AND STRIP, hardened and tempered Op. 01.01.1988 Dec. 01.01.1988 - TC 8735682 7211.23 HOOP AND STRIP, hardened and tempered Op. 01.07.1996 Dec. 01.07.1996 - TC 9606782 7211.29 HOOP AND STRIP, hardened and tempered Op. 01.07.1996 Dec. 11.06.1996 - TC 9605659 7211.29.00 STEEL STRIP, cold rolled, in coil form, having ALL of the following: (a) chemical composition by percentage of weight in accordance with EITHER of the compositions listed in THE TABLE; (b) dimensions, being ANY of the following width and thickness combinations: (i) 26 mm width (25.91/26.42 mm) x 4 mm thickness (3.90/4.12 mm); (ii) 26 mm width (25.91/26.42 mm) x 4.5 mm thickness (4.49/4.71mm); (iii) 39 mm width (38.61/39.12 mm) x 4 mm thickness (3.56/3.80 mm); (iv) 39 mm width (38.61/39.12 mm) x 5 mm thickness (4.83/5.09 mm), (c) camber tolerance in accordance with British Standard 1449 (BS1449) Part 1, Table 30 THE TABLE COMPOSITION 1 CARBON (C) NOT less than 0.37 and NOT greater than 0.44; MANGANESE (Mn) NOT less than 0.70 and NOT greater than 1.00; SILICON (Si) NOT less than 0.17 and NOT greater than 0.37; SULPHUR (S) NOT greater than 0.035; PHOSPHOROUS (P) NOT greater than 0.035; CHROMIUM (Cr) NOT greater than 0.25; NICKEL (Ni) less than 0.30; COPPER (Cu) NOT greater than 0.25 COMPOSITION 2 CARBON (C) NOT less than 0.42 and NOT greater than 0.50; MANGANESE (Mn) NOT less than 0.50 and NOT greater than 0.80; SILICON (Si) NOT less than 0.17 and NOT greater than 0.37; SULPHUR (S) less than 0.035; PHOSPHOROUS (P) less than 0.035; CHROMIUM (Cr) less than 0.25; NICKEL (Ni) less than 0.30; COPPER (Cu) less than 0.25 Op. 09.02.2010 Dec. 30.04.2010 - TC 1007032 7211.29.00 STRIP, STEEL, ANNEALED, fully spheroidized (NOT less than 95%), cold rolled, in coil form, being EITHER of the following: (a) grade SAE 1045, having a chemical composition by weight of BOTH of the following: (i) carbon NOT less than 0.42% and NOT greater than 0.50%; (ii) manganese NOT less than 0.50% and NOT greater than 0.80%; (b) grade SAE 1055, having a chemical composition by weight of BOTH of the following: (i) carbon NOT less than 0.52% and NOT greater than 0.60%;



(ii) mangenese NOT less than 0.60% and NOT greater than 0.90% Op. 17.06.2005 Dec. 02.09.2005 - TC 0507513 7211.29.00 STRIP, steel annealed, cold rolled, in coil form, having ALL of the following: (a) chemical composition by weight of BOTH of the following: (i) carbon - 0.45% to 0.50% (both inclusive); (ii) manganese - 0.65% to 0.90% (both inclusive) (b) to DIN standards 17 200 and 1 544; (c) in ANY of the following sizes: Width Thickness (i) 47.0 mm x 3.00 mm (ii) 84.0 mm x 2.26 mm (iii) 83.0 mm x 3.20 mm (iv) 62.0 mm x 4.00 mm (v) 95.0 mm x 4.50 mm (vi) 131.0 mm x 3.00 mm (d) width tolerance + or - 1.00 mm; (e) thickness tolerance + or - 0.09 mm Op. 01.07.1996 Dec. 11.06.1996 - TC 9605769 7211.90 HOOP AND STRIP, hardened and tempered Op. 01.01.1988 Dec. 01.01.1988 - TC 8735679 7212.20.00 STEEL, flat rolled, tin plated, coil form, continuous annealed, electro-galvanised zinc coated tab stock, having ALL of the following: (a) thickness gauge NOT greater than 0.4 mm; (b) width NOT greater than 90 mm; (c) coated internally and externally with food grade retortable varnish Op. 22.09.2005 Dec. 16.12.2005 - TC 0512719 7212.40.00 STEEL, flat rolled, in coil form, continuous annealed, zinc coated, epoxy lacquered, having BOTH of the following: (a) thickness NOT greater than 0.4 mm; (b) width NOT greater than 90 mm Op. 09.04.2009 Dec. 03.07.2009 - TC 0912184 7212.40.00 SHEETS AND/OR STRIPS, STEEL, NON-ORIENTATED ELECTRICAL, as described in ANY of the following international standards: (a) Japanese Industrial Standard C 2552; (b) American Society for Testing and Materials Standard A 677-05; (c) European Standard EN 10106 Op. 23.03.2006 Dec. 16.06.2006 - TC 0605626 7212.40.00 STEEL, cold rolled, less than 0.15% carbon, electro galvanized, coated with primer and chemically reactive adhesive system Op. 12.07.1993 Dec. 29.10.1993 - TC 9306903 7212.50 HOOP AND STRIP, steel, electrolytically nickel plated, in EITHER of the following sizes: (a) thickness NOT less than 0.3 mm; (b) thickness less than 0.3 mm AND width NOT exceeding 305 mm Op. 18.05.1984 Dec. 23.04.1985 - TC 8435169 7212.50.00 SHEETS AND/OR STRIPS, STEEL, NON-ORIENTATED ELECTRICAL, as described in ANY of the following international standards: (a) Japanese Industrial Standard C 2552; (b) American Society for Testing and Materials Standard A 677-05; (c) European Standard EN 10106



Op. 23.03.2006 Dec. 16.06.2006 - TC 0605627 7212.50.00 HOOP OR STRIP, thickness ranging from 0.2 mm to 1.2 mm, width less than 600 mm, electroplated with ANY of the following: (a) chromium; (b) brass; (c) copper; (d) nickel Op. 11.03.1994 Dec. 17.06.1994 - TC 9403622 7212.60.00 STRIP, STEEL, non-alloy, cold rolled, brass clad Op. 30.04.2008 Dec. 18.07.2008 - TC 0805896 7213.20.00 RODS, WIRE, hot rolled, free cutting steel, Grade 12L 14 Op. 07.11.2003 Dec. 30.01.2004 - TC 0314235 7213.91 RODS, tyre cord, dia 5.0 mm or greater but NOT exceeding 6.0 mm, to Specifications AISI 1070 M or AISI 1080 M Op. 01.07.1996 Dec. 12.06.1996 - TC 9607044 7214.30.00 BARS, HEXAGONAL, hot rolled, free cutting steel, grade 12 L 14 Op. 22.01.2007 Dec. 13.04.2007 - TC 0701138 7214.30.00 BARS, ROUND, hot rolled, free cutting steel, Grade 12L 14 Op. 07.11.2003 Dec. 30.01.2004 - TC 0314225 7214.91.00 BARS, NON-ALLOY STEEL, having ALL of the following: (a) rectangular cross-section; (b) electrical resistivity NOT greater than 20 Micro Ohms per centimetre; (c) carbon content NOT greater than 0.06 percent Op. 12.05.2008 Dec. 04.08.2008 - TC 0807796 7214.99.00 BARS, NON-ALLOY STEEL, having BOTH of the following: (a) electrical resistivity NOT greater than 20 Micro Ohms per centimetre; (b) carbon content NOT greater than 0.06 percent Op. 22.05.2008 Dec. 04.08.2008 - TC 0809491 7215.10 BARS, square, steel, bright OR cold finished, having an across flat dimension of 40 mm or greater but NOT exceeding 150 mm Op. 21.03.1985 Dec. 21.03.1985 - TC 8530419 7215.10.90 BARS, cold drawn, to American Iron and Steel Institute Standard C 12L14 (AISI C 12L14) Op. 15.10.2008 Dec. 14.01.2009 - TC 0835477 7215.10.90 BARS, hexagon, bright OR cold finished to AS 1443-1994 specifications, having an across the flat dimension in ANY of the following sizes: (a) 57.15 mm; (b) 60.325 mm; (c) 60.00 mm; (d) 62.00 mm OR greater Op. 03.03.1998 Dec. 11.05.1998 - TC 9801834 7215.50 BARS, flat, steel, bright or cold finished, having dimensions wider than 100 mm or thickness greater than 25 mm Op. 01.07.1996 Dec. 11.06.1996 - TC 9605781



7215.50 BARS, hexagon, bright or cold finished, having an across the flat dimension in ANY of the following sizes: (a) 57.15 mm (2 1/4 in. nominal); (b) 60.325 mm (2 3/8 in. nominal); (c) 60.00 mm; (d) 62.00 mm or greater Op. 01.07.1996 Dec. 11.06.1996 - TC 9605783 7215.50 BARS, square, steel, bright OR cold finished, having an across flat dimension of 40 mm or greater but NOT exceeding 150 mm Op. 01.07.1996 Dec. 11.06.1996 - TC 9605853 7215.50.90 BARS, rectangular, bright drawn carbon steel, greater than 3 mm width and thickness Op. 01.07.1996 Dec. 04.03.1996 - TC 9602575 7215.90 BARS, square, steel, bright or cold finished, having an across the flat dimension of 40 mm or greater but NOT exceeding 150 mm Op. 01.01.1988 Dec. 01.01.1988 - TC 8735564 7215.90 WELDING TRANSITION JOINTS, composed of dissimilar metals, explosion bonded, allowing dissimilar metals to be welded together Op. 31.03.1988 Dec. 13.10.1988 - TC 8803423 7215.90 BARS, flat, high carbon spring steel, tempered and hardened to give a tensile strength 80 to 90 tons/sq in, in straight lengths, cross sectional dimensions 9 to 13 mm wide, 2.5 to 5 mm thick Op. 07.05.1990 Dec. 09.08.1990 - TC 9004401 7215.90.00 BARS, bright or cold formed, leaded, chamfered at both ends, being EITHER of the following: (a) round, having a diameter NOT less than 3.17 mm and NOT greater than 90 mm; (b) hexagonal, having a cross sectional dimension from flat side to flat side NOT less than 3.17 mm and NOT greater than 90 mm Op. 11.09.2008 Dec. 05.12.2008 - TC 0830838 7216.32.00 I BEAMS, hot rolled, having EITHER of the following: (a) depth NOT less than 356 mm (14 in) and a flange width NOT less than 368 mm (14.5 in); (b) depth NOT less than 762 mm (30 in) and a flange width NOT less than 267 mm (10.5 in) Op. 04.10.2005 Dec. 03.01.2006 - TC 0513491 7216.50.00 BARS, MILD STEEL, being wheel rim profiles, length NOT less than 5 m Op. 19.12.2005 Dec. 10.03.2006 - TC 0516804 7216.50.00 SECTIONS, RIM ADAPTOR, DEMOUNTABLE STEEL TRUCK WHEEL RIM Op. 18.11.2002 Dec. 10.02.2003 - TC 0210924 7216.99.00 STRIP, SOIL REINFORCEMENT, having ALL of the following: (a) composition to Australian Standard AS3679.1 Grade 350 or equivalent; (b) hot rolled; (c) transverse ribs, having a height NOT less than 2.5 mm and NOT greater than 4.5 mm; (d) galvanized; (e) attachment holes at one or both ends of the strip; (f) width NOT less than 40 mm and NOT greater than 60 mm; (g) thickness NOT less than 3 mm and NOT greater than 10 mm, excluding height of ribs; (h) length NOT greater than 15 metres



Op. 30.04.2007 Dec. 20.07.2007 - TC 0706227 7217.10 WIRE, to the following Specifications: (a) ASTM A230; (b) DIN 17223 Op. 01.07.1996 Dec. 11.06.1996 - TC 9605787 7217.10 WIRE, oil tempered round edge hardened spring steel, to Specification AISI C 1070 Op. 01.07.1996 Dec. 11.06.1996 - TC 9605855 7217.10 WIRE, steel, to ANY of the following Specifications: (a) ASTM A230, A232 or A401; (b) SAE J351 or 50100 to 52100 (both inclusive); (c) DIN 17223; (d) BS 1408 Type D or 2803; (e) JIS G3561 Op. 01.07.1996 Dec. 12.06.1996 - TC 9606969 7217.10 WIRE, high carbon steel, in shapes (OTHER THAN rounds) with shaved edges, having BOTH of the following: (a) a chemical composition by weight of ALL of the following: (i) carbon - 0.65% to 1.05%; (ii) manganese - 0.20% to 0.80%; (iii) silicon - 0.15% to 0.35%; (iv) phosphorus - 0.03% maximum; (v) sulphur - 0.03% maximum; (b) in ANY of the following nominal dimensions: (i) 2.20 mm x 0.203 mm; (ii) 2.28 mm x 0.610 mm; (iii) 2.54 mm x 0.508 mm; (iv) 2.62 mm x 0.610 mm; (v) 3.05 mm x 0.610 mm; (vi) 3.43 mm x 0.610 mm; (vii) 3.81 mm x 0.610 mm; (viii) 4.19 mm x 0.610 mm; (ix) 6.14 mm x 0.457 mm Op. 01.07.1996 Dec. 19.06.1996 - TC 9607613 7217.10 WIRE, bright soft annealed, dia 0.44 mm or 0.70 mm Op. 01.07.1996 Dec. 20.06.1996 - TC 9607750 7217.10 WIRE, steel, high carbon, oil hardened and tempered, dia NOT exceeding 0.9 mm Op. 01.07.1996 Dec. 21.06.1996 - TC 9607805 7217.10 WIRE, oil tempered spring steel, having EITHER of the following: (a) a dia NOT exceeding 1.25 mm; (b) a dia exceeding 10.16 mm Op. 01.07.1996 Dec. 21.06.1996 - TC 9607806 7217.10 WIRE, music spring, having ANY of the following finishes: (a) bright; (b) cadmium; (c) cadmium/zinc alloy; (d) galvanised; (e) phosphate; (f) polished; (g) tinned Op. 01.07.1996 Dec. 21.06.1996 - TC 9607812 7217.10 WIRE, oil tempered round edge hardened spring steel, to Specification AISI C1065 in layer wound coils Op. 01.07.1996 Dec. 21.06.1996 - TC 9607813



7217.10 WIRE, brick cutting Op. 01.07.1996 Dec. 02.07.1996 - TC 9608374 7217.10.00 WIRES, FASTENER, complying with American Iron and Steel Institute (AISI) Standard 1022 Op. 16.05.2007 Dec. 07.08.2007 - TC 0707304 7217.10.00 WIRE, STEEL, having BOTH of the following: (a) diameter NOT less than 2.5 mm but NOT exceeding 3.5 mm; (b) chemical composition by weight of ALL of the following: (i) carbon 0.06% to 0.11%; (ii) phosphorus 0.04% to 0.08%; (iii) manganese 0.80% to 1.00%; (iv) silicon 0.01% maximum; (v) sulphur 0.015% to 0.07%; (vi) nickel 0.006% to 0.012%; (vii) aluminium 0.005% maximum Op. 26.09.2000 Dec. 08.12.2000 - TC 0008138 7217.10.00 WIRE, STEEL, having BOTH of the following: (a) diameter NOT less than 2.5 mm but NOT exceeding 3.5 mm; (b) chemical composition by weight of ALL of the following: (i) carbon 0.06% to 0.14%; (ii) phosphorus 0.03% to 0.09%; (iii) manganese 0.04% to 1.00%; (iv) silicon 0.14% maximum; (v) sulphur 0.01% to 0.04% Op. 24.04.2001 Dec. 20.07.2001 - TC 0103705 7217.20 WIRE, galvanised, dia less than 0.90 mm Op. 01.07.1996 Dec. 11.06.1996 - TC 9604139 7217.20 STAPLE WIRE, galvanised Op. 01.07.1996 Dec. 25.06.1996 - TC 9605656 7217.20 WIRE, galvanised, annealed, non-alloy steel, having ALL of the following characteristics: (a) diameter of 1.00 mm or less; (b) diameter tolerance + 0.02 mm - 0.01 mm; (c) tensile strength 300 - 400 N/mm2; (d) elongation 18% minimum; (e) torsion 44 turns minimum Op. 01.07.1996 Dec. 12.06.1996 - TC 9606972 7217.20.00 WIRE, steel, flat rolled with round edges, zinc coated, capable of a 30 degree angle edgewise bend around a 6.35 mm radius without surface cracking, having ALL the following: (a) dimensions; (i) width from 8.80 mm to 8.90 mm; (ii) thickness from 3.00 mm to 3.1 mm; (b) chemical composition by weight of ALL the following: (i) carbon 0.35% to 0.45%; (ii) copper 0.32% to 0.39%; (iii) manganese 0.5% to 0.8%; (iv) silicon 0.15% to 0.35%; (v) phosphorus maximum 0.045%; (vi) sulphur maximum 0.045% Op. 01.07.1996 Dec. 02.01.1996 - TC 9600025 7217.20.00 WIRE, steel, flat, rolled with round edges, zinc coated, capable of a 30 degree edgewise bend around a 6.35 mm radius without surface cracking, having ALL of the following: (a) dimensions: i) width from 7.75 mm to 7.85 mm;



ii) thickness from 3.00 mm to 3.1 mm; (b) chemical composition by weight of ALL of the following: i) carbon - 0.35% to 0.45%; ii) copper - 0.32% to 0.39%; iii) manganese - 0.5% to 0.8%; iv) silicon - 0.15% to 0.35%; v) phosphorus - maximum 0.045%; vi) sulphur - maximum 0.045% Op. 01.07.1996 Dec. 21.06.1996 - TC 9607834 7217.30 WIRE, steel, aluminium clad, complying with AS 1222 Part 2 Op. 01.07.1996 Dec. 12.06.1996 - TC 9607043 7217.30 WIRE, steel, conforming to specification AISI 1070 m Op. 01.07.1996 Dec. 12.06.1996 - TC 9607097 7217.30 STAPLE WIRE, liquor or copper coated Op. 01.07.1996 Dec. 12.06.1996 - TC 9607154 7217.30 WIRE, music spring, having ANY of the following finishes: (a) bright; (b) cadmium; (c) cadmium/zinc alloy; (d) galvanised; (e) phosphate; (f) polished; (g) tinned Op. 01.07.1996 Dec. 19.06.1996 - TC 9607636 7217.90 WIRE, cold drawn, fully killed, modified, spheroidised, annealed in process, phosphate coated to Specification AISI K1062M Op. 01.07.1996 Dec. 11.06.1996 - TC 9604145 7217.90 WIRE, fastener, soft drawn, to ANY of the following Specifications: (a) AISI Grade C1010; (b) AISI Grade C1018; (c) AISI Grade C1022; (d) AISI Grade K1012; (e) AISI Grade K1013; (f) AISI Grade K1016; (g) AISI Grade K1018; (h) AISI Grade K1019; (i) AISI Grade K1022; (j) AISI Grade K10B18; (k) AISI Grade K10B21 Op. 01.07.1996 Dec. 11.06.1996 - TC 9605663 7217.90 WIRE, fastener, soft drawn, to ANY of the following Specifications: (a) AISI Grade C1038; (b) AISI Grade C1039; (c) AISI Grade C1040; (d) AISI Grade C1041; (e) AISI Grade K1038; (f) AISI Grade K10B30 Op. 01.07.1996 Dec. 11.06.1996 - TC 9605664 7217.90 WIRE, music spring, having ANY of the following finishes: (a) bright; (b) cadmium; (c) cadmium/zinc alloy; (d) galvanised; (e) phosphate;



(f) polished; (g) tinned Op. 01.07.1996 Dec. 11.06.1996 - TC 9605786 7217.90.00 WIRE, FASTENER, cold heading quality non-alloy steels, diameter NOT less than 12 mm, in ANY of the following grades: (a) 1006; (b) 1008; (c) 1010; (d) 1019; (e) 1038; (f) 1137 Op. 17.02.2009 Dec. 15.05.2009 - TC 0905291 7217.90.00 WIRE, brass-plated high carbon steel Op. 08.04.2008 Dec. 04.07.2008 - TC 0802669 7217.90.00 WIRE, STEEL, being hard drawn low carbon (HDLC) wire, phosphate coated, having ALL of the following: (a) diameter NOT less than 18.00 mm but NOT greater than 20.00 mm; (b) chemical composition by weight of ALL of the following: (i) carbon 0.04% to 0.10%; (ii) phosphorus 0.03% maximum; (iii) manganese 0.40% to 0.60%; (iv) silicon 0.12% to 0.24%; (v) sulphur 0.03% maximum Op. 11.08.2008 Dec. 31.10.2008 - TC 0825942 7217.90.00 WIRE, SPIRAL BINDING, nylon coated, continuous roll, diameter 0.74 mm to 2.00 mm (inclusive) Op. 01.07.1996 Dec. 11.03.1996 - TC 9603035 7217.90.00 WIRE, fastener, soft drawn, to specification AISI grade K 4037 Op. 01.07.1996 Dec. 21.06.1996 - TC 9607835 7217.90.00 WIRE BEAD, bronze plated steel, having BOTH of the following: (a) carbon content NOT less than 0.69%; (b) tensile strength NOT less than 1 750 N/mm2 Op. 24.05.2004 Dec. 20.08.2004 - TC 0404954 7218.10.00 INGOTS, stainless steel, weight exceeding 2.5 tonnes Op. 22.07.1993 Dec. 29.10.1993 - TC 9307092 7218.99.00 BILLETS, stainless steel, square or round, in ANY of the following grades: (a) UNS S32750; (b) UNS S31803; (c) UNS S08904; (d) UNS S30815 Op. 01.07.1996 Dec. 21.04.1996 - TC 9604885 7218.99.00 BILLETS, stainless steel, square or round, annealed, having ALL of the following: (a) a section measurement of NOT less than 300 mm; (b) in ANY of the following grades: (i) 304; (ii) 304 L; (iii) 304 H; (iv) 316; (v) 316 L; (vi) 316 H; (vii) 321; (viii) 321 H



Op. 13.02.2003 Dec. 28.04.2003 - TC 0301541 7218.99.00 BILLETS OR BLOOMS, stainless steel, square, forged and ground, having a section measurement of NOT less than 75 mm and NOT greater than 500 mm Op. 29.11.2004 Dec. 04.02.2005 - TC 0413053 7219.12.00 COILS, stainless steel, to ASTM A240, in ANY of the following grades: (a) 316; (b) 316L; (c) 304; (d) 304L; (e) 321; (f) UNS S41050 Op. 27.03.1997 Dec. 30.07.1997 - TC 9702511 7219.12.00 FLAT ROLLED PRODUCTS OF STAINLESS STEEL, having a thickness of 4.75 mm or more but NOT exceeding 10 mm Op. 02.06.1997 Dec. 15.08.1997 - TC 9704869 7219.13.00 FLAT ROLLED PRODUCTS OF STAINLESS STEEL, having a thickness of 3 mm or more but less than 4.75 mm Op. 02.06.1997 Dec. 15.08.1997 - TC 9704872 7219.21 FLAT ROLLED PRODUCTS, having a nickel content exceeding 22.5% by weight Op. 01.01.1988 Dec. 01.01.1988 - TC 8800536 7219.21.00 FLAT ROLLED PRODUCTS, stainless steel, Grade UNS S30815, having a chemical composition by weight of ALL of the following: (a) carbon 0.1% maximum; (b) silicon 1.40% to 2.00% (both inclusive); (c) manganese 0.8% maximum; (d) phosphorous 0.040% maximum; (e) sulphur 0.030% maximum; (f) chromium 20% to 22% (both inclusive); (g) nickel 10% to 12% (both inclusive); (h) cerium 0.03% to 0.08% (both inclusive); (i) nitrogen 0.14% to 0.20% (both inclusive) Op. 21.01.1994 Dec. 29.04.1994 - TC 9401453 7219.21.00 PLATES, stainless steel, types 304 and 316 to ASTM A240 Op. 21.11.1994 Dec. 19.05.1995 - TC 9409119 7219.21.00 PLATES, SHEET AND FLATS, stainless steel, to specification DIN X42Cr13, AISI 420 or ASTM 420 Op. 14.02.1995 Dec. 31.05.1995 - TC 9504085 7219.21.00 PLATES, stainless steel, to specification ASTM A240, having a thickness exceeding 10 mm and a width exceeding 600 mm Op. 31.05.1995 Dec. 08.09.1995 - TC 9505858 7219.21.00 PLATES OR SHEET, stainless steel, to standard AISI 420 Op. 10.04.1996 Dec. 12.07.1996 - TC 9605616 7219.21.00 FLAT ROLLED PRODUCTS OF STAINLESS STEEL, having a thickness exceeding 10 mm Op. 02.06.1997 Dec. 15.08.1997 - TC 9704868 7219.22 FLAT ROLLED PRODUCTS, having a nickel content exceeding 22.5% by weight Op. 01.01.1988 Dec. 01.01.1988 - TC 8800535



7219.22.00 FLAT ROLLED PRODUCTS, stainless steel, Grade UNS 31803, having a chemical composition, by weight, of ALL of the following: (a) carbon 0.3% maximum; (b) chromium 21.0-23.0% inclusive; (c) nickel 4.5-6.5% inclusive; (d) molybdenum 2.5-3.5% inclusive; (e) nitrogen 0.08-0.20% inclusive; (f) silicon 1.0% maximum; (g) manganese 2.0% maximum; (h) phosphorus 0.03% maximum; (i) sulphur 0.02% maximum Op. 10.12.1992 Dec. 12.03.1993 - TC 9300330 7219.22.00 FLAT ROLLED PRODUCTS, stainless steel, Grade UNS S30815, having a chemical composition by weight of ALL of the following: (a) carbon 0.1% maximum; (b) silicon 1.40% to 2.00% (both inclusive); (c) manganese 0.8% maximum; (d) phosphorous 0.040% maximum; (e) sulphur 0.030% maximum; (f) chromium 20% to 22% (both inclusive); (g) nickel 10% to 12% (both inclusive); (h) cerium 0.03% to 0.08% (both inclusive); (i) nitrogen 0.14% to 0.20% (both inclusive) Op. 21.01.1994 Dec. 29.04.1994 - TC 9401452 7219.22.00 PLATES, stainless steel, types 304 and 316 to ASTM A240, having a thickness greater than 6mm Op. 21.11.1994 Dec. 19.05.1995 - TC 9409118 7219.22.00 PLATES, stainless steel, to specification ASTM A240, having a thickness exceeding 6 mm but NOT exceeding 10 mm and a width exceeding 600 mm Op. 31.05.1995 Dec. 08.09.1995 - TC 9505856 7219.22.00 FLAT ROLLED PRODUCTS OF STAINLESS STEEL, having a thickness of 4.75 mm or more but NOT exceeding 10 mm Op. 02.06.1997 Dec. 15.08.1997 - TC 9704870 7219.23.00 FLAT ROLLED PRODUCTS OF STAINLESS STEEL, having a thickness of 3 mm or more but less than 4.75 mm Op. 02.06.1997 Dec. 15.08.1997 - TC 9704878 7219.24.00 FLAT ROLLED PRODUCTS OF STAINLESS STEEL, having a thickness of less than 3 mm Op. 02.06.1997 Dec. 15.08.1997 - TC 9704894 7219.31.00 FLAT ROLLED PRODUCTS OF STAINLESS STEEL, having a thickness of 4.75 mm or more Op. 02.06.1997 Dec. 15.08.1997 - TC 9704877 7219.32 FLAT ROLLED PRODUCTS, having a nickel content exceeding 22.5% by weight Op. 01.01.1988 Dec. 01.01.1988 - TC 8800531 7219.32.00 FLAT ROLLED PRODUCTS, stainless steel, Grade UNS 31803, having a chemical composition, by weight, of ALL the following: (a) carbon 0.03% maximum; (b) chromium 21.0-23.0% inclusive; (c) nickel 4.5-6.5% inclusive; (d) molybdenum 2.5-3.5% inclusive; (e) nitrogen 0.08-0.20% inclusive; (f) silicon 1.0% maximum; (g) manganese 2.0% maximum;



(h) phosphorus 0.03% maximum; (i) sulphur 0.02% maximum Op. 10.12.1992 Dec. 16.03.1993 - TC 9300334 7219.32.00 PLATES, SHEETS OR COILS, stainless steel, to ASTM A240, in ANY of the following grades: (a) 316; (b) 316L; (c) 304; (d) 304L; (e) 321; (f) UNS S41050; (g) 430 Op. 27.03.1997 Dec. 30.07.1997 - TC 9702513 7219.32.00 FLAT ROLLED PRODUCTS OF STAINLESS STEEL, having a thickness of 3 mm or more but less than 4.75 mm Op. 02.06.1997 Dec. 15.08.1997 - TC 9704893 7219.33.00 COILS, stainless steel, cold rolled, AISI type 436, having BOTH the following: (a) width exceeding 600 mm; (b) thickness 1.0 mm or greater but NOT exceeding 3.0 mm Op. 24.03.1993 Dec. 12.07.1993 - TC 9308961 7219.33.00 STAINLESS STEEL STRIP, cold rolled, heat resisting, ferritic, type 409, in coils, AISI type 2D finish, having the following dimensions: (a) thickness 1.5 mm, 1.2 mm, or 2.0 mm (+ or - 10%); (b) width between 600 mm and 1 300 mm inclusive Op. 04.10.1996 Dec. 13.12.1996 - TC 9611258 7219.33.00 PLATES, SHEETS OR COILS, stainless steel, to ASTM A240, in ANY of the following grades: (a) 316; (b) 316L; (c) 304; (d) 304L; (e) 321; (f) UNS S41050; (g) 430 Op. 27.03.1997 Dec. 30.07.1997 - TC 9702503 7219.33.00 FLAT ROLLED PRODUCTS OF STAINLESS STEEL, having a thickness exceeding 1 mm but less than 3 mm Op. 02.06.1997 Dec. 15.08.1997 - TC 9704859 7219.34.00 COILS, stainless steel, cold rolled, AISI type 436, having BOTH the following: (a) width exceeding 600 mm; (b) thickness 0.5 mm or greater but NOT exceeding 1.0 mm Op. 24.03.1993 Dec. 12.07.1993 - TC 9308956 7219.34.00 STAINLESS STEEL STRIP, cold rolled, heat resisting, ferritic, type 409, in coils, AISI type 2D finish, having the following dimensions; (a) thickness 0.9 mm, 0.6 mm, or 1.00 mm (+ or - 10%); (b) width between 600 mm and 1 300 mm inclusive Op. 04.10.1996 Dec. 13.12.1996 - TC 9611259



7219.34.00 PLATES, SHEETS OR COILS, stainless steel, to ASTM A240, in ANY of the following grades: (a) 316; (b) 316L; (c) 304; (d) 304L; (e) 321; (f) UNS S41050 Op. 27.03.1997 Dec. 30.07.1997 - TC 9702502 7219.34.00 FLAT ROLLED PRODUCTS OF STAINLESS STEEL, having a thickness of 0.5 mm or more but NOT exceeding 1 mm Op. 02.06.1997 Dec. 15.08.1997 - TC 9704860 7219.35 FLAT ROLLED PRODUCTS, stainless steel, having BOTH of the following: (a) a width of 600 mm or greater; (b) a thickness of 0.25 mm or less Op. 17.05.1989 Dec. 21.08.1989 - TC 8903648 7219.35.00 PLATES, SHEETS OR COILS, stainless steel, to ASTM A240, in ANY of the following grades: (a) 316; (b) 316L; (c) 304; (d) 304L; (e) 430 Op. 27.03.1997 Dec. 30.07.1997 - TC 9702499 7219.35.00 FLAT ROLLED PRODUCTS OF STAINLESS STEEL, having a thickness of less than 0.5 mm Op. 02.06.1997 Dec. 15.08.1997 - TC 9704861 7219.90 SHEET, stainless steel, perforated, conforming to ANY of the following nominal sizes listed in THE TABLE THE TABLE Thickness Hole size Hole centre spacing (a) 0.30 mm 0.50 mm 1.1 mm; (b) 0.45 mm 0.70 mm 1.2 mm; (c) 0.45 mm 0.75 mm 1.2 mm; (d) 0.50 mm 1.00 mm 1.5 mm Op. 16.09.1986 Dec. 27.03.1987 - TC 8635617 7219.90.00 SHEET, COMPOSITE, stainless steel laminated with polyvinyl chloride, having BOTH of the following: (a) steel thickness NOT less than 0.6 mm; (b) polyvinyl chloride laminate thickness NOT less than 0.8 mm Op. 01.08.2005 Dec. 21.10.2005 - TC 0510004 7219.90.00 FLAT ROLLED PRODUCTS OF STAINLESS STEEL Op. 02.06.1997 Dec. 15.08.1997 - TC 9704862 7219.90.00 CAUL PLATES (melamine press plates), stainless steel, being 2 650 mm x 1 350 mm OR greater Op. 16.11.1998 Dec. 22.01.1999 - TC 9810123 7220.11.00 PLATES, SHEETS AND FLATS, stainless steel, to specification DIN X42Cr13, AISI 420 or ASTM 420 Op. 14.02.1995 Dec. 31.05.1995 - TC 9504087 7220.11.00 FLAT ROLLED PRODUCTS OF STAINLESS STEEL, having a thickness of 4.75 mm or more Op. 02.06.1997 Dec. 15.08.1997 - TC 9704863



7220.12 BARS OR STRIP, stainless steel, hot rolled, coil form, in ANY of the sizes listed in the following TABLE THE TABLE Thickness Width (a) less than 0.55 mm less than 152 mm (b) 0.55 mm to 3 mm less than 24 mm (c) greater than 3 mm less than 25 mm Op. 14.07.1994 Dec. 14.07.1994 - TC 9217823 7220.12.00 FLAT ROLLED PRODUCTS OF STAINLESS STEEL, having a thickness of less than 4.75 mm Op. 02.06.1997 Dec. 15.08.1997 - TC 9704865 7220.20 STRIP, stainless steel, thickness less than 0.26 mm, of rectangular section, of a width NOT exceeding 500 mm and of such dimension that the thickness does NOT exceed one tenth of the width Op. 28.02.1984 Dec. 28.02.1984 - TC 8437425 7220.20 FLAT-ROLLED PRODUCTS, having a nickel content exceeding 22.5% by weight Op. 01.01.1988 Dec. 01.01.1988 - TC 8733278 7220.20 BARS OR STRIP, stainless steel, flat, cut to length in any of the sizes listed in the following TABLE THE TABLE Thickness Width (a) less than 0.55 mm less than 152 mm; (b) 0.55 mm to 3 mm less than 24 mm; (c) greater than 3 mm less than 25 mm; (d) greater than 13 mm less than 204 mm Op. 13.07.1995 Dec. 13.07.1995 - TC 9508169 7220.20.00 BANDING, stainless steel, to AISI 201 or 316, of a width less than 35 mm and a thickness of less than 1.25 mm Op. 18.05.1993 Dec. 30.08.1993 - TC 9304905 7220.20.00 STRIP, stainless steel, grade 301, in coils, thickness NOT exceeding 0.3 mm, width NOT exceeding 600 mm Op. 11.04.1994 Dec. 15.07.1994 - TC 9404089 7220.20.00 PLATES, SHEETS OR COILS, stainless steel, to ASTM A240, in ANY of the following grades: (a) 316; (b) 316L; (c) 304; (d) 304L; (e) 321; (f) UNS S41050; (g) 430 Op. 27.03.1997 Dec. 30.07.1997 - TC 9702580 7220.20.00 FLAT ROLLED PRODUCTS OF STAINLESS STEEL, NOT further worked than cold-rolled (cold-reduced) Op. 02.06.1997 Dec. 15.08.1997 - TC 9704864 7220.90.00 STRIP, stainless steel, type 434, coated on one or both sides with primer and chemically reactive adhesive system Op. 21.03.1994 Dec. 02.08.1994 - TC 9403739 7220.90.00 FLAT ROLLED PRODUCTS OF STAINLESS STEEL Op. 02.06.1997 Dec. 15.08.1997 - TC 9704866



7221.00 BARS AND RODS, hot rolled in irregularly wound coils, stainless steel, Dia. 40mm or less Op. 29.09.1992 Dec. 15.01.1993 - TC 9209110

Documents

Customs Tariff Concessions 7201_to_7221