Upload
abdillah-arifin-rahman-lubis
View
7
Download
0
Tags:
Embed Size (px)
DESCRIPTION
Configuration OMSN R4
Citation preview
Alcatel University - 3FL 40034 AEAA WBZZA Ed.013.1
3 Equipment Configuration
3.2
3 Equipment ConfigurationSession presentation
Objective: to be able to configure a network element Program:
3.1 OMSN Configuration3.2 Board Substitution/Database Clearing3.3 Specific Configuration3.4 ISA board Configuration
Alcatel University - 3FL 40034 AEAA WBZZA Ed.013.3
3 Equipment Configuration
3.1 OMSN Configuration
3.4
3.1 OMSN ConfigurationBoards Alarms
Replaceable unit missing. This alarm indicates that there is configured a board in the software that doesnt exist in the hardware .
Replaceable unit type mismatch. This alarm indicates that there is configured a board in the software but it isn't the right one.
Unconfigured equipment present. This alarm indicates that the board is plugged in the equipment but the board isnt configured in the software.
Replaceable unit problem.The board could be broken.
3.5
3.1 OMSN ConfigurationSetting Procedure
Is
the slot
empty?
Select an alarmed slot in the subrack view
SET the board OUT OF SERVICE
REMOVE the board
SET the board
Yes
No
Isthere the padlock?
Procedure that has to be executed for every board/module that has one of the alarm seen
before
END
Find the correct board with the REMOTE INVENTORY
No
Yes
3.6
3.1 OMSN Configuration Exercise
9 Set one equipment.
Time allowed : 25 minutes
Alcatel University - 3FL 40034 AEAA WBZZA Ed.013.7
3 Equipment Configuration
3.2 Board Substitution/Database Clearing
3.8
3.2 Board Substitution/Database Clearing Procedure for clearing the database
To start with the BASIC CONFIGURATION it is necessary to clear the Database of the Equipment Controller(EC) following this procedure
I- Extract the EC card.II- Move the micro-switch inside the card as indicated in figure 2 below.III- Insert the EC card and wait until the leds on the front of the board turn on.IV- Verify that the database is cleared: all the slots appear empty, except for the
following main cards: EC card , MATRIX, CONGI and Bus Termination.V- Extract the EC card, set the micro-switch in the original position: a warning alarm
appears in the slots where a card is inserted.
EQUICO, SYNTH1N
ON
OFF
1 2 3 4ON
OFF
1 2
PQ2/EQC, SYNTH4
ON
OFF
1 2 3 4ON
OFF
1 2 Normal operating condition
figure 1
Move the switch#2 from OFF to ON to clean the database
figure 2
3.9
3.2 Board Substitution/Database ClearingSubstitution of the EC card
New unit hw condition.Unit with wrong or
unknown sw?New unit hw condition.
Unit without sw?New unit hw condition.Unit with different sw?
New unit hw condition.Sw of the same release and NE?
Hw-preset the new unit with: switch#1=OFF, switch#2=ON (reset database)Insert the new unit
Remove and hw-preset the new unit with: switch#1=ON, switch#2=ON.
Insert the new unit again
Download the NE relevant sw release with normal
download procedure
Download the NE relevant sw release with
SIBDL procedure
Remove and hw-preset the new unit with: switch#1=ON, switch#2=OFF(reset database and upload comm/routing tables)
Insert the new unit again
Is the MIB stored in the Craft Terminal?
From CT send the saved MIB containing the correct configuration
From OS send the saved MIB containing the correct configuration
From CT activate the sent MIBFrom OS activate the sent MIB
Remove and hw-preset the new unit with: switch#1=OFF, switch#2=OFF(normal operating condition)Insert the new unit again
YESNO
3.10
3.2 Board Substitution/Database ClearingSubstitution of ATM card
I1-4: switch#4
3.11
3.2 Board Substitution/Database Clearing Exercise
9 Change the EQUICO or SYNTH board. Remember to save the configuration data with Mib Management function in Download menu before clearing the database.
Time allowed : 30 minutes
Alcatel University - 3FL 40034 AEAA WBZZA Ed.013.12
3 Equipment Configuration
3.3 Specific Configuration
3.13
3.3 Specific ConfigurationAuto Laser Shutdown
Select SPIPort Physical MediaALS ManagementSelect SPIPort Physical MediaALS Management
3.14
3.3 Specific ConfigurationTP Configuration: RST
In Port View select RST Port TP Configuration
3.15
3.3 Specific ConfigurationTP Configuration: VC4 and VC3
In Port View select VC4 or VC3 Port TP Configuration
3.16
3.3 Specific ConfigurationTP Configuration: VC12
In Port View select VC12 Port TP Configuration
3.17
3.3 Specific ConfigurationTP Threshold Configuration
(i.e.) In Port View select MST Port TP Thresholds Configuration
Poisson Distribution
BurstyDistribution
3.18
3.3 Specific ConfigurationRetiming Function
3.19
3.3 Specific ConfigurationIntroduction on E1 and P12
PDH Signal with AIS
111
111 RX
100
011
POH
VC12
PAYLOAD with errored
bits
RX
TX
TX
100
011
UPSTREAM UPSTREAM
DOWNSTREAMDOWNSTREAM
: Errored bits
PAYLOAD with errored
bits
3.20
3.3 Specific ConfigurationTP Frame Mode Configuration
In Port View select P12 Port TP Frame Mode Configuration
3.21
3.3 Specific ConfigurationChange 140Mbit/s interface into 155Mbit/s interface
PDH 140Mbit/s interface
SDH 155Mbit/s Electrical interface
3.22
3.3 Specific ConfigurationPort Mode
Alcatel University - 3FL 40034 AEAA WBZZA Ed.013.23
3 Equipment Configuration
3.4 ISA board Configuration
3.24
3.4 ISA board ConfigurationPort Configuration
Time Slot Switch
STM1 Number
STM1 Time Slot
For creating a new port
SignalConcatenation Level
For assigning a newSTM1 Time Slotand/or a new STM1 Number to the selected VC
3.25
3.4 ISA board Configuration Control Path Activation
3.26
3.4 ISA board Configuration LCAS Configuration
3.27
3.4 ISA board Configuration LCAS Monitoring
3.28
3.4 ISA board Configuration Ethernet Port Configuration
3.29
3.4 ISA board Configuration Ethernet Mapping Protocol configuration
E
T
H
-
M
B
GETH-MB
PR-EA ES1-8FE
ISA-ES16ES4-8FE
ES1-8FX
3.30
3 Equipment ConfigurationEvaluation
Objective: to be able to configure a network element
Thank you for answeringthe self-assessment
of the objectives sheet
3 Equipment Configuration3 Equipment ConfigurationSession presentation3 Equipment Configuration3.1 OMSN ConfigurationBoards Alarms3.1 OMSN ConfigurationSetting Procedure3.1 OMSN Configuration Exercise3 Equipment Configuration3.2 Board Substitution/Database Clearing Procedure for clearing the database3.2 Board Substitution/Database Clearing Substitution of the EC card3.2 Board Substitution/Database ClearingSubstitution of ATM card3.2 Board Substitution/Database Clearing Exercise3 Equipment Configuration3.3 Specific Configuration Auto Laser Shutdown3.3 Specific Configuration TP Configuration: RST3.3 Specific ConfigurationTP Configuration: VC4 and VC33.3 Specific Configuration TP Configuration: VC123.3 Specific ConfigurationTP Threshold Configuration3.3 Specific Configuration Retiming Function3.3 Specific Configuration Introduction on E1 and P123.3 Specific Configuration TP Frame Mode Configuration3.3 Specific ConfigurationChange 140Mbit/s interface into 155Mbit/s interface3.3 Specific ConfigurationPort Mode3 Equipment Configuration3.4 ISA board ConfigurationPort Configuration3.4 ISA board Configuration Control Path Activation3.4 ISA board Configuration LCAS Configuration3.4 ISA board Configuration LCAS Monitoring3.4 ISA board Configuration Ethernet Port Configuration3.4 ISA board Configuration Ethernet Mapping Protocol configuration3 Equipment ConfigurationEvaluation