Compact Multi-voltage Photoelectric Sensor [Power Supply ... · Power Supply Built-in Amplifier-separated NX5 VF Interference prevention Conforming to Low Voltage and EMC Directive

407

Related InformationFIBERSENSORS

LASERSENSORS

PHOTOELECTRICSENSORS

MICROPHOTOELECTRIC

SENSORS

AREASENSORS

LIGHTCURTAINS

PRESSURE / FLOW

SENSORSINDUCTIVEPROXIMITY

SENSORS

PARTICULARUSE SENSORS

SENSOROPTIONS

SIMPLEWIRE-SAVING

UNITS

WIRE-SAVING SYSTEMS

MEASUREMENTSENSORS

STATIC CONTROLDEVICES

ENDOSCOPE

LASERMARKERS

PLC /TERMINALS

HUMAN MACHINE INTERFACES

ENERGY CONSUMPTION VISUALIZATION COMPONENTS

FA COMPONENTS

MACHINE VISION SYSTEMS

UV CURING SYSTEMS

Selection Guide

Amplifier Built-in

Power Supply Built-in

Amplifier-separated

NX5

VF

Interferenceprevention

Conforming to Low Voltageand EMC Directive

Multi-voltage

Multi-voltageThe NX5 series can operate at 24 to 240 V AC or 12 to 240 V DC, which is suitable for supply voltages around the world.

Direct hook-up to an AC power supply

No need to arrange a DC power supply.

Compact sizeDespite of being multi-voltage, it has a depth of just 35 mm 1.378 in.(W18 × H62 × D35 mm W0.709 × H2.441 × D1.378 in)

Conventional model Compared to theconventional modelDepth: 1/2Width: 2/3Volume: 1/3

NX5

Webサササ

Long sensing rangeIt is most suitable for conveyor lines and parking lot applications.

30 m 98.425 ft (Infrared LED)

700 mm 27.559 in(Infrared LED)

Thru-beam

7 m 22.966 ft (Infrared LED)

10 m 32.808 ft (Red LED)

5 m 16.404 ft(Red LED with polarizing filters)

Retroreflective

Diffuse reflective

High reliabilityIt has an IP66 protection. Moderate dust or water splashes will not affect the sensor.The hermetically sealed output relay significantly increases its reliability.

Hermetically sealed relay eliminates worries about bad contact

BASIC PERFORMANCE

FUNCTIONS / MOUNTINGEasy alignmentThe 10 m 32.808 ft thru-beam type sensor and the 5 m 16.404 ft retroreflective type sensor incorporate a red LED beam source. Beam alignment can be attained by checking the emitted beam visually.

Interference preventionTwo sensors can operate normally even if mounted close together.(Excluding the 30 m 98.425 ft thru-beam type sensor)

Multi-voltage photoelectric sensorusable worldwide

Certified

Compact Multi-voltage Photoelectric Sensor Power Supply Built-in

NX5 SERIES General terms and conditions ........... F-17 Sensor selection guide ................. P.283~

panasonic-electric-works.net/sunx

Glossary of terms / General precautions .........P.1359~ / P.1405 China’s CCC mark ........................ P.1409

Compact Multi-voltage Photoelectric Sensor NX5 SERIES 408

Selection GuideAmplifier Built-inPower Supply Built-inAmplifier-separated

NX5

VF

FIBERSENSORS

LASERSENSORS

PHOTO-ELECTRICSENSORSMICROPHOTO-ELECTRICSENSORS

AREASENSORS

LIGHTCURTAINS

PRESSURE / FLOWSENSORS

INDUCTIVEPROXIMITYSENSORS


SENSOROPTIONS

SIMPLEWIRE-SAVINGUNITS

WIRE-SAVING SYSTEMS

MEASURE-MENTSENSORS


ENDOSCOPE

LASERMARKERS

PLC /TERMINALS

HUMAN MACHINE INTERFACESENERGY CONSUMPTION VISUALIZATION COMPONENTS

FA COMPONENTS


UV CURING SYSTEMS

ORDER GUIDE

Type Appearance Sensing range Model No.(Note 2, 3)

Emittingelement Output

Thru

-bea

m

Ligh

t-O

N

10 m 32.808 ftNX5-M10RA

Red LED

Relay contact 1c

Dar

k-O

N NX5-M10RB

Long

sen

sing

rang

e

Ligh

t-O

N

30 m98.425 ft

NX5-M30AInfrared LED

Dar

k-O

N NX5-M30B

Ret

rore

flect

ive

With

pol

ariz

ing

filte

rs

Ligh

t-O

N

0.1 to 5 m 0.328 to 16.404 ft(Note 1)

NX5-PRVM5ARed LED

Dar

k-O

N NX5-PRVM5B

Long

sen

sing

rang

e

Ligh

t-O

N

0.1 to 7 m 0.328 to 22.966 ft(Note 1)

NX5-RM7AInfrared LED

Dar

k-O

N NX5-RM7B

Diff

use

refle

ctiv

e

Ligh

t-O

N

700 mm 27.559 inNX5-D700A

Infrared LED

Dar

k-O

N NX5-D700B

Thru-beam type Retroreflective type Diffuse reflective type

NX5-M10RA and NX5-M30A(Light-ON)

NX5-PRVM5A and NX5-RM7A(Light-ON)

NX5-D700B(Dark-ON)

Notes: 1) The sensing range of the retroreflective type sensor is specified for the RF-230 reflector. Further, the sensing range is the possible setting range for the reflector. The sensor can detect an object less than 0.1 m 0.328 ft away.

0.1 m 0.328 ft

Sensor

Reflector

Reflector cannot beplaced in this range

Reflector

5 m 16.404 ft(NX5-RM7: 7 m 22.966 ft)

Setting rangeof the reflector

Actual sensing rangeof the sensor

2) The model No. with “P” shown on the label affixed to the thru-beam type sensor is the emitter, “D” shown on the label is the receiver. (e.g.) Emitter of NX5-M10RA: NX5-M10RP,

Receiver of NX5-M10RA: NX5-M10RAD3) Light-ON type sensor (model No. with suffix “A”) and Dark-ON type

sensor (model No. with suffix “B”) are available in the NX5 series. For the following models, in case of power off, the output relay condition is the same as when an object is detected. (In case of power supply line disconnection, the output operation is the same as when an object is detected.) Refer to ‘‘I/O CIRCUIT DIAGRAM AND OUTPUT OPERATION’’ for the output operation of each model.

5 m 16.404 ft cable length type5 m 16.404 ft cable length type (standard: 2 m 6.562 ft ) is also available.When ordering this type, suffix “-C5” to the model No.(e.g.) 5 m 16.404 ft cable length type of NX5-M10RA is “NX5-M10RA-C5”.

Accessory•RF-230 (Reflector)

NOTE: Mounting bracket is not supplied with the sensor. Please select from the range of optional sensor mounting brackets (three types).

APPLICATIONS

Detecting car position at parking garage Detecting objects on conveyor line

Foot biangled mountingbracket

409 Compact Multi-voltage Photoelectric Sensor NX5 SERIES

Selection Guide

Amplifier Built-in


Amplifier-separated

NX5

VF

FIBERSENSORS

LASERSENSORS

PHOTO-ELECTRICSENSORS

MICROPHOTO-

ELECTRICSENSORS

AREASENSORS

LIGHTCURTAINS

PRESSURE / FLOW

SENSORS

INDUCTIVEPROXIMITY

SENSORS

PARTICULARUSE

SENSORS

SENSOROPTIONS

SIMPLEWIRE-SAVING

UNITS

WIRE-SAVING SYSTEMS

MEASURE-MENT

SENSORS


ENDOSCOPE

LASERMARKERS

PLC /TERMINALS

HUMAN MACHINE

INTERFACESENERGY

CONSUMPTION VISUALIZATION COMPONENTS

FA COMPONENTS

MACHINE VISION

SYSTEMS

UV CURING

SYSTEMS

OPTIONS

Designation Model No. Description

Sensor mounting bracket

MS-NX5-1 Foot angled mounting bracket(The thru-beam type sensor needs two brackets.)

MS-NX5-2 Foot biangled mounting bracket (sensor protection bracket)(The thru-beam type sensor needs two brackets.)

MS-NX5-3 Back angled mounting bracket(The thru-beam type sensor needs two brackets.)

Slit maskFor thru-beamtype sensoronly

OS-NX5-3×6Slit size 3 × 6 mm0.118 × 0.236 in

Slit on one side

• Sensing range: 3 m 9.843 ft [NX5-M10R] 16 m 52.493 ft [NX5-M30]

• Min. sensing object: ø10 mm ø0.394 in [NX5-M10R]ø20 mm ø0.787 in [NX5-M30]

Slit on both sides• Sensing range: 1 m 3.281 ft [NX5-M10R]

6 m 19.685 ft [NX5-M30]• Min. sensing object: 3 × 6 mm 0.118 × 0.236 in

Interference prevention filter

For NX5-M10RAor NX5-M10RBonly

PF-NX5-V(Vertical,Silver) Same type of filters on both sides

• Sensing range: 5 m 16.404 ft• Min. sensing object: ø20 mm ø0.787 in

(One set consists of 2 pcs. of interference prevention filters.)PF-NX5-H(Horizontal, Light brown)

ReflectorFor retrore-flective typesensor only

RF-210• Sensing range: 0.1 to 1.5 m 0.328 to 4.921 ft [NX5-PRVM5]

0.1 to 2.5 m 0.328 to 8.202 ft [NX5-RM7]• Min. sensing object: ø30 mm ø1.181 in

RF-220• Sensing range: 0.1 to 3.5 m 0.328 to 11.483 ft [NX5-PRVM5]

0.1 to 5 m 0.328 to 16.404 ft [NX5-RM7]• Min. sensing object: ø35 mm ø1.378 in

Reflector mounting bracket

MS-RF21-1 Protective mounting bracket for RF-210It protects the reflector from damage and maintains alignment.

MS-RF22 For RF-220

MS-RF23 For RF-230

Reflective tapeFor retrore-flective typesensor only

RF-11• Ambient temperature:

–25 to +50 °C –13 to +122 °F• Ambient humidity: 35 to 85 % RH

Notes• Keep the tape free from stress.

If it is pressed too much, its capability may deteriorate.

• Do not cut the tape. It will deteriorate the sensing performance.

• Sensing range:0.1 to 0.8 m 0.328 to 2.625 ft

[NX5-PRVM5]0.1 to 1 m 0.328 to 3.281 ft

[NX5-RM7]

RF-12

• Sensing range:0.1 to 1 m 0.328 to 3.281 ft

[NX5-PRVM5]0.1 to 1.5 m 0.328 to 4.921 ft

[NX5-RM7]

Sensor checker(Note) CHX-SC2

It is useful for beam alignment of thru-beam type sensors.The optimum receiver position is given by indicators, aswell as an audio signal.

Note: Refer to the sensor checker CHX-SC2 pages for details.

Sensor mounting bracket•MS-NX5-1 •MS-NX5-2

Two M4 (length 25 mm 0.984 in) screws with washers and two M4 nuts are attached.



•MS-NX5-3

Slit mask•OS-NX5-3×6

Fitted on the front face of the sensor with one touch.

Interferencepreventionfilter(For NX5-M10R only)

• PF-NX5-V(Vertical, Silver color)• PF-NX5-H(Horizontal, Light brown)

Two sets of thru-beam type sensors (Red LED type) can be mounted close together.

Reflector•RF-210 •RF-220

Reflectivetape

Reflectormountingbracket•MS-RF23 •MS-RF22 •MS-RF21-1

Two M4 (length 10 mm 0.394 in) screws with washers are attached.



•RF-11 •RF-12

30 mm1.181 in

8 mm0.315 in

0.7 mm0.028 in

25 mm0.984 in

0.7 mm0.028 in

30 mm1.181 in

Sensor checker•CHX-SC2

LEVEL

POWER CHX-SC2

Sensor checker

33.3 mm1.311 in

12.8 mm0.504 in

11 mm0.433 in

35.3 mm1.390 in

8.3 mm0.327 in

42.3 mm1.665 in



NX5

VF

FIBERSENSORS

LASERSENSORS


AREASENSORS

LIGHTCURTAINS




SENSOROPTIONS


WIRE-SAVING SYSTEMS

MEASURE-MENTSENSORS


ENDOSCOPE

LASERMARKERS

PLC /TERMINALS


FA COMPONENTS


UV CURING SYSTEMS

SPECIFICATIONS

TypeThru-beam Retroreflective

Diffuse reflectiveLong sensing range With polarizing filters Long sensing range

Item Model No. NX5-M10RA NX5-M10RB NX5-M30A NX5-M30B NX5-PRVM5A NX5-PRVM5B NX5-RM7A NX5-RM7B NX5-D700A NX5-D700BSensing range 10 m 32.808 ft 30 m 98.425 ft 0.1 to 5 m 0.328 to 16.404 ft (Note 2) 0.1 to 7 m 0.328 to 22.966 ft (Note 2) 700 mm 27.559 in (Note 3)

Sensing object ø20 mm ø0.787 in or more opaque object (Note 4)

ø20 mm ø0.787 in or more opaque object (Completely beam interrupted object) (Note 4)

ø50 mm ø1.969 in or more opaque, translucent or specular object (Note 2, 5)

ø50 mm ø1.969 in or more opaque or translucent object (Note 2, 5)

Opaque, translucent or transparent object (Note 5)

Hysteresis – 15 % or less of operation distance (Note 3)

Repeatability (perpendicular to sensing axis) 0.1 mm 0.004 in or less 0.2 mm 0.008 in or less 0.3 mm 0.012 in or less

Supply voltage 24 to 240 V AC +10–15 % or 12 to 240 V DC +10

–15 % Ripple P-P 10 % or less

Power consumption Emitter: 1 VA or lessReceiver: 2 VA or less

Emitter: 1.5 VA or lessReceiver: 2 VA or less 2 VA or less

Output

Relay contact 1 c• Switching capacity: 250 V AC 1 A (resistive load)

30 V DC 2 A (resistive load)• Electrical life: 500,000 or more switching operations (switching frequency 3,600 operations/hour)

100,000 or more switching operations (switching frequency 3,600 operations/hour)• Mechanical life: 100 million or more switching operations (switching frequency 36,000 operations/hour)

Output operation Light-ON Dark-ON Light-ON Dark-ON Light-ON Dark-ON Light-ON Dark-ON Light-ON Dark-ON

Response time 10 ms or less

Operation indicator Red LED (lights up when the output is ON)

Stability indicator Green LED (lights up under stable light received condition or stable dark condition)

Power indicator – Red LED(lights up when the power is ON)

–

Sensitivity adjuster Continuously variable adjuster – Continuously variable adjuster – Continuously variable adjuster

Automatic interference prevention function

Use optional interferenceprevention filters

– Incorporated (Two units of sensors can be mounted close together.)

Env

ironm

enta

l res

ista

nce

Pollution degree 3 (Industrial environment)

Protection IP66 (IEC)

Ambient temperature –20 to +55 °C – 4 to +131 °F (No dew condensation or icing allowed) (Note 6), Storage: –30 to +70 °C –22 to +158 °F

Ambient humidity 35 to 85 % RH, Storage: 35 to 85 % RH

Ambient illuminance Incandescent light: 3,500 ℓx at the light-receiving face

EMC EN 61000-6-2, EN 61000-6-4

Voltage withstandability 1,500 V AC for one min. between power supply and output terminals, 1,000 V AC for one min. between relay contact terminals

Insulation resistance 20 MΩ, or more, with 500 V DC megger between power supply and output terminals, and between relay contact terminals

Vibration resistance 10 to 55 Hz frequency, 1.5 mm 0.059 in amplitude in X, Y and Z directions for two hours each

Shock resistance 500 m/s2 (50 G approx.) in X, Y and Z directions for three times each

Emitting element Red LED (modulated) Infrared LED (modulated) Red LED (modulated) Infrared LED (modulated)

Peak emission wavelength 660 nm 0.026 mil 880 nm 0.035 mil 660 nm 0.026 mil 880 nm 0.035 mil

Material Enclosure: Polycarbonate, Lens: Polycarbonate, Cover: Polycarbonate, Front cover (retroreflective type sensor only): Acrylic

Cable 0.3 mm2 5-core (thru-beam type emitter: 2-core) cabtyre cable, 2 m 6.562 ft long

Cable extension Extension up to total 100 m 328.084 ft is possible with 0.3 mm2, or more, cable (thru-beam type: both emitter and receiver).

Net weight Emitter: 100 g approx.Receiver: 140 g approx.

Emitter: 125 g approx.Receiver: 140 g approx. 140 g approx.

Accessories Adjusting screwdriver: 1 pc. – RF-230 (Reflector): 1 pc.Adjusting screwdriver: 1 pc. RF-230 (Reflector): 1 pc. Adjusting screwdriver: 1 pc.

Notes: 1) Where measurement conditions have not been specified precisely, the conditions used were an ambient temperature of +23 °C +73.4 °F. 2) The sensing range and the sensing object of the retroreflective type sensor is specified for the RF-230 reflector. Further, the sensing range is the

possible setting range for the reflector. The sensor can detect an object less than 0.1 m 0.328 ft away.

0.1 m 0.328 ft

Sensor

Reflector

Setting rangeof the reflector

Reflector cannot beplaced in this range

Reflector

Actual sensing rangeof the sensor

5 m 16.404 ft (NX5-RM7: 7 m 22.966 ft)

3) The sensing range and the hysteresis of the diffuse reflective type sensor are specified for white non-glossy paper (200 × 200 mm 7.874 × 7.874 in) as the object.

4) If slit masks (optional) are fitted, an object as small as 3 × 6 mm 0.118 × 0.236 in can be detected.5) Make sure to confirm detection with an actual sensor before use.6) In case the sensor is to be used at an ambient temperature of –15 °C +5 °F, or less, please contact our office.


Selection Guide

Amplifier Built-in


Amplifier-separated

NX5

VF

FIBERSENSORS

LASERSENSORS


MICROPHOTO-

ELECTRICSENSORS

AREASENSORS

LIGHTCURTAINS

PRESSURE / FLOW

SENSORS

INDUCTIVEPROXIMITY

SENSORS

PARTICULARUSE

SENSORS

SENSOROPTIONS

SIMPLEWIRE-SAVING

UNITS

WIRE-SAVING SYSTEMS

MEASURE-MENT

SENSORS


ENDOSCOPE

LASERMARKERS

PLC /TERMINALS

HUMAN MACHINE

INTERFACESENERGY


FA COMPONENTS

MACHINE VISION

SYSTEMS

UV CURING

SYSTEMS

I/O CIRCUIT DIAGRAM AND OUTPUT OPERATION

I/O circuit diagram

Color code

Brown

Blue

Black

Gray

White

Output relay

Supply voltage24 to 240 V AC %

or 12 to 240 V DC %

NO

NC

COM.

Internal circuit

Multi-voltagecircuit

Sen

sor c

ircui

t

+10–15

+10–15

Note: The emitter of the thru-beam type sensor has two wires for power (+V and 0 V) only.

SENSING CHARACTERISTICS (TYPICAL)

NX5-M30A NX5-M30B Thru-beam type

Parallel deviation Angular deviation Parallel deviation with slit masks (3 × 6 mm 0.118 × 0.236 in)

2,00078.740

1,00039.370

0 1,00039.370

2,00078.740

0

1032.808

2065.617

40131.234

3098.425

Emitter

Receiver

L

Left RightCenterOperational point ℓ (mm in)

Set

ting

dist

ance

L (m

ft)

ℓ

10 5 0 5 10

3098.425

40131.234

2065.617

1032.808

0

Left RightCenterOperating angle θ ( ° )

Set

ting

dist

ance

L (m

ft)

Receiver

Emitter

Lθ

60023.622

30011.811

0 30011.811

60023.622

0

516.404

1032.808

2065.617

1549.213

Set

ting

dist

ance

L (m

ft)

Slit onone side

Slit onboth sides

Left RightCenterOperating point ℓ (mm in)

Emitter

Receiver

L ℓ

1,00039.370

50019.685

0 50019.685

1,00039.370

0

1032.808

516.404

Emitter

Receiver

L

Left RightCenterOperational point ℓ (mm in)

Set

ting

dist

ance

L (m

ft)

ℓ

20 10 0 10 200

1032.808

516.404

(Down) Left

Horizontaldirection

Verticaldirection Receiver

Emitter

L

Right (Up)CenterOperating angle θ ( ° )

Set

ting

dist

ance

L (m

ft)

θ

NX5-M10RA NX5-M10RB Thru-beam type

Parallel deviation Angular deviation Parallel deviation with slit masks (3 × 6 mm 0.118 × 0.236 in)

2007.874

1003.937

0 1003.937

2007.874

0

13.281

26.562

413.123

39.843 Slit on

one side

Slit onboth sides

Set

ting

dist

ance

L (m

ft)


Emitter

Receiver

L ℓ

Output operation

Sensing modeThru-beam & Retroreflective type Diffuse reflective type

Light-ON (A) type Dark-ON (B) type Light-ON (A) type Dark-ON (B) type

Output NO(Black cable)

NC(Gray cable)

NO(Black cable)

NC(Gray cable)

NO(Black cable)

NC(Gray cable)

NO(Black cable)

NC(Gray cable)

Outpu

t con

dition Power OFF Open Close Open Close Open Close Open Close

Beam-received Close Open Open Close Close Open Open Close

Beam-interrupted Open Close Close Open Open Close Close Open

: Object detected state.



NX5

VF

FIBERSENSORS

LASERSENSORS


AREASENSORS

LIGHTCURTAINS




SENSOROPTIONS


WIRE-SAVING SYSTEMS

MEASURE-MENTSENSORS


ENDOSCOPE

LASERMARKERS

PLC /TERMINALS


FA COMPONENTS


UV CURING SYSTEMS

For plotting the left graph, the sensitivity has been set such that a 200 × 200 mm 7.874 × 7.874 in white non-glossy paper is just detectable at a distance of 700 mm 27.559 in.

SENSING CHARACTERISTICS (TYPICAL)

2007.874

1003.937

0 1003.937

2007.874

0

26.562

413.123

826.247

619.685

Sensor

L

Reflector(RF-230)

Set

ting

dist

ance

L (m

ft)

ℓ


40 20 0 20 40

619.685

826.247

413.123

26.562

0


Set

ting

dist

ance

L (m

ft)

Reflector angulardeviation

Sensor angulardeviation

Sensor angulardeviationReflector (RF-230)

Sensor Sensor

Reflector angulardeviationReflector (RF-230)

LLθ

θ

Retroreflective typeNX5-PRVM5A NX5-PRVM5B Retroreflective typeNX5-RM7A NX5-RM7B

Parallel deviation Angular deviation Parallel deviation Angular deviation

NX5-D700A NX5-D700B Diffuse reflective type

Sensingfield Correlation between sensing object size and sensing range

As the sensing object size becomes smaller than the standard size (white non-glossy paper 200 × 200 mm 7.874 × 7.874 in), the sensing range shortens, as shown in the left graph.

2007.874

1003.937

0 1003.937

2007.874

0

Set

ting

dist

ance

L (m

ft)


Sensor

L

Reflector(RF-230)

ℓ 2

6.562

413.123

826.247

619.685

40 20 0 20 40

619.685

826.247

413.123

26.562

0


Set

ting

dist

ance

L (m

ft)

Reflector angulardeviation

Sensor angulardeviation

Sensor angulardeviationReflector (RF-230)

Sensor Sensor

Reflector angulardeviationReflector (RF-230)

LLθ

θ

401.575

200.787

0 200.787

401.575

0

2007.874

40015.748

80031.496

60023.622

L

Sensor

Set

ting

dist

ance

L (m

m in

)

ℓ


200 × 200 mm7.874 × 7.874 inWhite non-glossy paper

0 2007.874

30011.811

40015.748

L

Sensor

Sen

sing

rang

e L

(mm

in)

White non-glossy paperside length a (mm in)

2007.874

40015.748

80031.496

60023.622

1003.937

a × a mma × a inWhite non-glossy paper

PRECAUTIONS FOR PROPER USE Refer to General precautions.

Mounting

• The tightening torque should be 0.8 N·m or less.

M4 (length 25 mm 0.984 in)screw with washers

Sensor mounting bracket (Optional)

M4 nuts

Others

• Do not use during the initial transient time (50 ms) after the power supply is switched on.

• Although the protection degree is specified for the sensor including the cable, the cable end is not waterproof, and is not covered by the protection specified. Hence, make sure that water does not seep in from the cable end.

Interferencepreventionfilter(ExclusivelyforNX5-M10R)

• Use the interference prevention filters (optional) when two units of thru-beam type sensors are mounted close together. However, take note that the sensing range will become short.

Interference prevention filterFitted with PF-NX5-V(Vertical, Silver coior)

Interference prevention filterFitted with PF-NX5-H(Horizontal, Light brown)

Note: The filters cannot be used for NX5-M30A or NX5-M30B.

• Never use this product as a sensing device for personnel protection.

• In case of using sensing devices for personnel protection, use products which meet laws and standards, such as OSHA, ANSI or IEC etc., for personnel protection applicable in each region or country.

• There are 2 types of interference prevention filters. Install PF-NX5-H (Horizontal, Light brown) for 1 set, and install PF-NX5-V (Vertical, Silver color) for the other set.


Selection Guide

Amplifier Built-in


Amplifier-separated

NX5

VF

FIBERSENSORS

LASERSENSORS


MICROPHOTO-

ELECTRICSENSORS

AREASENSORS

LIGHTCURTAINS

PRESSURE / FLOW

SENSORS

INDUCTIVEPROXIMITY

SENSORS

PARTICULARUSE

SENSORS

SENSOROPTIONS

SIMPLEWIRE-SAVING

UNITS

WIRE-SAVING SYSTEMS

MEASURE-MENT

SENSORS


ENDOSCOPE

LASERMARKERS

PLC /TERMINALS

HUMAN MACHINE

INTERFACESENERGY


FA COMPONENTS

MACHINE VISION

SYSTEMS

UV CURING

SYSTEMS

Retroreflectivetypesensor(NX5-RM7)

• Please take care of the following points when detecting materials having a gloss.

L

10° to 30°

Sensor

Glossysurface

Reflector

Sensingobject

Make L sufficiently long1 Make L, shown in the diagram, sufficiently long.

2 Install at an angle of 10 to 30 degrees to the sensing object.

* NX5-PRVM5 does not need the above adjustment.

Retroreflectivetypesensorwithpolarizingfilters(NX5-PRVM5)

• If a shiny object is covered or wrapped with a transparent film, such as those described below, the retroreflective type sensor with polarizing filters may not be able to detect it.In that case, follow the steps given below.

Example of sensing objects• Can wrapped by clear film• Aluminum sheet covered by plastic film• Gold or silver color (specular) label or wrapping paper

Steps• Tilt the sensor with respect to the sensing object while

fitting.• Reduce the sensitivity.• Increase the distance between the sensor and the

sensing object.

DIMENSIONS (Unit: mm in) The CAD data in the dimensions can be downloaded from our website.

SensorNX5-M10RA NX5-M10RB NX5-M30A NX5-M30B

Beam axis

200.787

Stabilityindicator(Green) (Note 3) Operation indicator

(Red) (Note 1, 3)

Sensitivity adjuster (Note 2, 3)

351.378

622.441

501.969

40.157

2-ø4.5 ø0.177 mounting holes2-M4 nut seats (on both sides)

50.197

250.984

ø5.8 ø0.228 cable, 2 m 6.562 ft long

6 0.236

180.709

SensorNX5-PRVM5A NX5-PRVM5B NX5-RM7A NX5-RM7B

SensorNX5-D700A NX5-D700B

20.50.807

180.709 35

1.378

622.441

501.969

50.197

250.984

Stabilityindicator(Green)

Center ofsensing

Operation indicator(Red)

Sensitivity adjuster


Beam-receiving part

Beam-emitting part

6 0.236

ø5.8 ø0.228 cable, 2 m 6.562 ft long

40.157

Notes: 1) It is the power indicator (red) on the emitter of NX5-M30.2) Not incorporated on NX5-M30.3) Not incorporated on the emitter.

Center ofsensing

20.50.807

Stabilityindicator(Green)

Operation indicator(Red)

Sensitivity adjuster (Note)

501.969


50.197

250.984

Beam-receiving part

Beam-emitting part

622.441

351.378

6 0.236

ø5.8 ø0.228 cable, 2 m 6.562 ft long

40.157

180.709

Note: Not incorporated on NX5-RM7.

PRECAUTIONS FOR PROPER USE Refer to General precautions.



NX5

VF

FIBERSENSORS

LASERSENSORS


AREASENSORS

LIGHTCURTAINS




SENSOROPTIONS


WIRE-SAVING SYSTEMS

MEASURE-MENTSENSORS


ENDOSCOPE

LASERMARKERS

PLC /TERMINALS


FA COMPONENTS


UV CURING SYSTEMS

Reflector (Optional)RF-210

33.31.311

ReflectorM3 nut mounting holes(for mounting at the back)

Base

250.984

3.20.126

100.394

2-ø3.4 ø0.134 thru-holes(for mounting at the side)

(for mounting at the back)

2-ø3.4 ø0.134 holes, 6 0.236 deep

(for mounting at the side)2-M3 nut mounting holes

12.8 0.504

11 0.433

Material: Acrylic (Reflector) ABS (Base)

Two M3 (length 8 mm 0.315 in)screws with washers and two nuts are attached.

Reflective tape (Optional)RF-11 Reflective tape (Optional)RF-12

80.315

281.102

301.181

Adhesivetape

Effective reflecting surface

0.70.028( )

( )60.236

( )

301.181

0.70.028

281.102

250.984

230.906

AdhesivetapeEffective

reflecting surface

( )

Material: Acrylic

Material: Acrylic

2-ø4.6 ø0.181mountingholes

50.31.980

401.575

5 0.197

8.30.327

3.30.130

10 0.394

59.32.335

49.31.941

( )301.181

35.31.390

42.31.665

34.31.350

250.984

2-ø3.6 ø0.142mountingholes

4 0.1578 0.315

8.30.327

3.30.130

210.827( )



Reflector (Accessory for the retroreflective type sensor)RF-230 Reflector (Optional)RF-220



Selection Guide

Amplifier Built-in


Amplifier-separated

NX5

VF

FIBERSENSORS

LASERSENSORS


MICROPHOTO-

ELECTRICSENSORS

AREASENSORS

LIGHTCURTAINS

PRESSURE / FLOW

SENSORS

INDUCTIVEPROXIMITY

SENSORS

PARTICULARUSE

SENSORS

SENSOROPTIONS

SIMPLEWIRE-SAVING

UNITS

WIRE-SAVING SYSTEMS

MEASURE-MENT

SENSORS


ENDOSCOPE

LASERMARKERS

PLC /TERMINALS

HUMAN MACHINE

INTERFACESENERGY


FA COMPONENTS

MACHINE VISION

SYSTEMS

UV CURING

SYSTEMS

MS-NX5-1 Sensor mounting bracket (Optional)

t 2t 0.079

9.4 0.370

5.20.205

6.40.252 25 0.984

120.472 22

0.866

ø6.4 ø0.252 hole

401.575

5°

5°4.5

0.177

501.969

150.591

301.181 72

2.835

250.984

60.236 25

0.984250.984

291.142

2-ø4.5 ø0.177 holes

R55.9R2.201

Assembly dimensionsMounting drawing with the receiver of NX5-M10R

10°

401.575

722.835

6.40.252 25

0.984

120.472 22

0.866

5.20.20521

0.82740

1.575(43)

(1.693)

ø6.4 ø0.252

512.008

t 2t 0.079

Beam axis

Material: Cold rolled carbon steel (SPCC) (Uni-chrome plated)

Two M4 (length 25 mm 0.984 in)screws with washers and two M4 nuts are attached.

Sensor mounting bracket (Optional)MS-NX5-2


401.575

903.543

1044.094

60.236

6.40.252

10°

50.197

t 2t 0.079

140.551

250.984

Beam axis

562.205

60.236

250.984

702.756

t 2t 0.079

60.236

140.551

170.669

291.142

100.394

80.315

40 1.57537

1.45760.236

6.40.252

501.969

4.50.177

5°

5°15

0.59125

0.984

120.472

301.181

36.61.441

903.543

1044.094R28

R1.102

MS-NX5-3 Sensor mounting bracket (Optional)

t 2t 0.079

501.969

180.709

250.984

5.50.217

60.236

2-ø4.5 ø0.177 holes

4.50.177 5°

5°5.5

0.21725

0.984

451.772

301.181

501.969

642.520

220.866

120.472

9.50.374

6.40.252

50.197

60.236

421.654

6.40.252

6.40.252

R55.9R2.201


10°

t 2t 0.079

451.772

642.520

210.827

6.40.252

180.709

60.236

6.40.252

401.575

100.394

50.19712

0.472

(43)(1.693)

Beam axis

220.866

421.654

DIMENSIONS (Unit: mm in)


Two M4 (length 25 mm 0.984 in) screws with washers andtwo M4 nuts are attached.


Two M4 (length 25 mm 0.984 in) screws with washers andtwo M4 nuts are attached.

The CAD data in the dimensions can be downloaded from our website.



NX5

VF

FIBERSENSORS

LASERSENSORS


AREASENSORS

LIGHTCURTAINS




SENSOROPTIONS


WIRE-SAVING SYSTEMS

MEASURE-MENTSENSORS


ENDOSCOPE

LASERMARKERS

PLC /TERMINALS


FA COMPONENTS


UV CURING SYSTEMS


MS-RF22 Reflector mounting bracket for RF-220 (Optional)

Assembly dimensions

4.50.177

100.394

110.433

250.984

351.378

40.157

16 0.630

10 0.394

6 0.2368 0.315

441.732

200.787

t 1.6t 0.063

8-M3 × 0.5 0.020thru-hole threads

250.984

4.50.177

250.984

100.394 28.3

1.114

8.30.327

34.31.350

8 0.315

40.157

210.827

35.31.390

44.31.744

60.236

271.063

t 1.6t 0.063

19.30.760

( ) ( )



MS-RF23 Reflector mounting bracket for RF-230 (Optional)

Assembly dimensions40

1.575 4.50.177

30.118 10

0.394 110.433

501.969

401.575

5 0.197

16 0.630

15 0.591

18 0.709

7 0.276

200.787

t 2t 0.079

8-M4 × 0.7 0.028 thru-hole threads

261.024

120.472

351.378

30.118

612.402

( )

( ) 281.102( )

401.5754.5

0.177

28.31.11419.3

0.760

8.30.327

100.394

50.31.980

49.31.941

50.197

t 2t 0.07910

0.394

301.181

61.32.413

70.276

371.457

401.575

( )( )



MS-RF21-1 Reflector mounting bracket for RF-210 (Optional)

Assembly dimensions

12.5 0.492

t 1.2t 0.047

130.512

ø25ø0.984

160.63010

0.3943.50.1383.2

0.126

R7.5R0.295

250.984

461.811

20°

230.906

501.969

5.50.217

ø36ø1.417

30°

461.811 25

0.984

130.512

100.394

20°

501.969

ø36ø1.417

30°

230.9065.5

0.217

Material: Stainless steel (SUS304)


Documents

Compact Multi-voltage Photoelectric Sensor [Power Supply ... · Power Supply Built-in Amplifier-separated NX5 VF Interference prevention Conforming to Low Voltage and EMC Directive