Embed Size (px)
Citation preview
:: MDS-SERIES (CISCO) COMMANDS :: http://www.cisco.com/en/US/products/ps5989/prod_command_reference_list.html
MDS-SERIES Switch Commands
ip address 191.168.123.234 255.255.255.0
View = ~ show running-config
show environment ~ shows status of all installed hardware components
show flogi database ~ shows database list of all FLOGI events
show fcns database ~ shows database list of all N-ports logged in
show vsan membership ~ shows list of VSAN members
show interface brief ~ lists the interfaces and status
MDS-SERIES Zoning Commands
config terminal ~Enters configuration terminal
fcalias ~creates an alias for a member
zone name TestZone1 vsan 4 ~ creates a zone
member pwwn 10:01:10:01:10:ab:cd:ef ~ adds node to the zone above
no member pwwn <colon separated wwn> ~deletes member from zone
zoneset name Zoneset1 vsan 4 ~ creates a zoneset
member <zone name> ~adds zone to the ZoneSet above
no zone name <zone name> vsan <vsan Id> ~ Deletes a zone
zoneset activate name Zoneset1 vsan 4
zone copy active-zoneset full-Zoneset1 vsan 4
copy running-config start-up config ~ copy from source to startup configuration
vsan database ~ go into vsan configuration mode
vsan 4 interface fc3/21 ~move port 21 on module 3 to vsan 4
show zoneset ~ shows all zonesets that are active
show zone vsan <#> ~ shows all zones active in vsan
show zoneset active ~ displays the active zoneset
show vsan ~ shows the vsans on the switch
show zoneset active vsan <vsan Id> ~ Shows active zoneset
:: B-SERIES (BROCADE) COMMANDS :: http://powerlink.emc.com/km/appmanager/km/secureDesktop?internalId=0b01406680024e88
B-SERIES Switch Commands
ipAddrSet ~set the IP address of a Brocade switch
SetContext <VF Number> ~choose which Virtual Fabric all the commads to be run in
switchShow ~ display switch info
supportShow ~ full detailed switch info
portShow # ~ display port info
nsShow ~ Name server contents
nsAllShow ~ NS for full fabric
fabricShow ~ fabric information
ad --create ~create a new Admin Domain.
B-SERIES Zoning Commands
aliCreate “Alias”, “20:00:00:e0:69:40:07:08”
zoneCreate “Zone1”, “20:00:00:e0:69:40:07:08; 50:06:04:82:b8:90:c1:8d”
cfgCreate “Test_cfg”, “Zone1; Zone2”
cfgSave ~ saves zoning information across reboots
cfgEnable “Test_cfg” ~enable a zoneset config,
zoneShow or cfgShow ~ shows defined and effective zones and configurations
zoneAdd ~ adds a member to a zone
zoneRemove ~ removes a member from a zone
zoneDelete ~ deletes a zone
cfgAdd ~ adds a zone to a zone configuration
cfgRemove ~ removes a zone from a zone configuration
::Veritas VM HOST COMMANDS :: http://www.symantec.com/business/support/documentation.jsp?language=english&view=manuals&pid=15273
Veritas VM Device Commands
vxdisk list ~ List all disks under volume manager control and give there status.
vxdiskadd c1t2d3 ~ add or bring a disk under volume manager control
vxdiskadmin ~ Interactive front end to the vxdisk program
Veritas VM Filesystem commands
vxdisk init ~ Initialize Physical Volume
vxdg init mydg mydg-01=c1t11d0 ~ Create Disk Group
vxassist -g mydg make myvol <size> ~ Create Logical Volume
mkfs -F vxfs /dev/vx/rdsk/mydg/myvol ~ create file system
vxvol -g mydg stopall ~ stop a volume
vxdg deport mydg ~ deport disk group
vxdg import mydg ~ import disk group
vxvol -g mydg startall ~ starting a imported volume
::VMware ESX HOST COMMANDS :: http://www.vmware.com/support/developer/vcli/
VMware ESX Device Commands
esxcfg-info Print out device configurations
esxcfg-module -l List modules loaded in the service console
vmkfstools (-P, -q, -g) ~RDM Target LUN information
esxcfg-advcfg
esxcfg-resgrp
esxcfg-auth ~A uthentication configuration
VMware ESX Storage commands
esxcfg-info –s ~General Storage Info
vdf -h ~Disk Space Utilization
fdisk /dev/sdX ~
esxcfg-scsidevs -A ~prints a mapping between the HBA and the devices
esxcfg-nas -a ~Adds a new NAS file system to the ESX/ESXi host.
esxcfg-boot Manage the boot partitions
esxcfg-dumppart -l Manage the vmkdump partition
esxcfg-mpath –l ~Path information
esxcfg-vmhbadevs –m ~VMKernel-to-Service Console Device Mapping
esxcfg-rescan <vmkernel adpter> ~scan for new disks
esxcfg-swiscsi –e ~enable iSCSI initiator
esxcfg-rescan ~Rescan LUNs on SCSI device
esxcfg-resgrp ~Create, delete and list resource groups
vmkpcidivy –q vmhba_devs ~map canonical name to Vmware file system
VMware ESX Networking commands
esxcfg-firewall
esxcfg-nics ~Presents physical NIC information
esxcfg-route ~Enable or disable routing for vmknics
esxcfg-swscsi ~Configures software iSCSIadapters
esxcfg-vmhbadevs ~Maps COS device files to vmhbanames
esxcfg-vmknic ~Create & configure VMkernel NICs
esxcfg-vswif ~Create & configure vswifsfor the COS
esxcfg-vswitch ~Create & configure virtual switches andport groups
:: Windows HOST COMMANDS :: http://support.microsoft.com/default.aspx/ph/3198?sid=26
Windows 2003 server SP1 Device Commands
SystemInfo ~ Displays detailed configuration information about a computer and its operating system
Shutdown /r /f ~ forced reboot
Netstat ~ Displays active TCP connections, ports on which the computer is listening
mstsc /v: 255.255.255.255 /console ~ launches a Remote desktop Connection
net use \\ComputerName\ShareName\volume ~ Connects a computer to a computer shared resource
FC ~ compares two files and displays the differences
ChkDsk ~ check and repair disk problems
Recover ~ Recover a damaged file from a defective disk.
fcinfo /details ~ if fcinfo is installed ,this will list the HBA’s wwns
Windows 2003 server SP1 LVM Commands
Diskpart rescan ~ Locates new disks that may have been added to the computer
Diskpart list disk ~ Displays a list of disks and information about them,
Diskpart detail disk ~ Displays the properties of the selected disk and the volumes on that disk.
wmic partition get BlockSize, StartingOffset, Name, Index ~find the starting offset Diskpart create partition primary align=64 ~create a properly offset partition
MountVol ~ Creates, deletes, or lists a volume mount point.
Diskpart assign ~ Assigns a drive letter or mount point to the volume with focus.
Diskpart extend ~ Extends the volume with focus into next contiguous unallocated space
Diskpart import ~ Imports a foreign disk group into the local computer's disk group
Format /FS:filesystem ~ Specifies the type of the file system (FAT, FAT32, or NTFS).
FSutil volume dismount
:: VI COMMANDS :: Cursor movements
h ~ left one character
l ~ right one character
j ~ down one line
k ~ up one line
w ~ right one word
b ~ back one word
Deleting, Yanking, and Pasting
d ~ delete
x ~ delete character cursor is on
r ~ replace one character
y ~ yank (copy into temporary buffer)
Y ~ yank line cursor is on
p ~ paste below cursor line (deleted or copied text)
Saving and Exiting
u ~ undo last editing command
ZZ ~ save and exit (hold down shift and press "z" twice)
:wq! ~ write and quit even if it is read-only
:: FTP COMMANDS :: open <IP address> ~ undo last editing command
close <IP address> ~ save and exit (hold down shift and press "z" twice)
bin ~set to transfer for binary and text files
hash ~display progress during get
mget ~mutiple get – download files in to current directory
mput ~multiple pu – upload files from current directory
:: AIX/IBM HOST COMMANDS :: http://publib.boulder.ibm.com/infocenter/pseries/v5r3/index.jsp?topic
AIX Software Installation
/usr/lpp ~ Software Directory
lslpp -L all ~ List installed software
lslpp -f fileset ~ List all files
instfix –i ~ List installed patches
cp *.lpp /usr/sys/inst.images ~ copy lpp software to the install directory
smit installp ~ Install a software package
rmdev ~ Remove a device
AIX Device Commands
lscfg ~ lists all comfigured components
smit or smitty ~ system management utility
lscfg –v l <interface> ~ lists all attributes (WWN’s) for a device
emc_cfgmgr ~ configures symmetrix devices
mkbcv ~ makes BCV visable to AIX to avoid locking during boot
(1) chdev -l fcsX -a init_link=pt2pt –P ~ “To change INIT Link flags parameter”
(2) chdev -l fscsiX -a fc_err_recov=fast_fail –P ~ “Fabric Event Error RECOVERY Policy”
(3) cfgmgr –v ~ cofigures devices and optionally installs device software
AIX NFS Commands
exportfs ~Lists all exported filesystems
exportfs -a ~Exports all fs's in /etc/exports file
exportfs -u (filesystem) ~Un-exports a filesystem
mknfs ~Configures and starts NFS services
rmnfs ~Stops and un-configures NFS services
mknfsexp -d /directory ~Creates an NFS export directory
mknfsmnt ~Creates an NFS mount directory
mount hostname:/filesystem /mount-point ~Mount an NFS filesystem
nfso -a ~Display NFS Options
AIX iSCSI Commands
smit iscsi
AIX Filesystem Commands http://the-welters.com/professional/aix/jfs-lvm.html
lsdev –Cc disk ~ Device Listing and status
mkdev ~ configures a disk device masking sue it is available as a physical volume
chdev -l hdisk# -a pv=yes ~ Initialize Physical Volume
lspv -l hdisk# ~ Disk Label
mkvg -y myvg -s 16 hdisk2 ~ groups one or more physical devices into a volume group
mirrorvg ~Creates mirror volumes for all volumes in a volume group. extendvg myvg hdisk3 hdisk4 ~ Extend Volume Goup
lsvg –l vgname ~ displays volumes, with a specified volume group
mklv -y mylv myvg 16 ~ Make logical volume
mklvcopy hd1 2 hdisk1 ~(2) makes a copy of lv should be followed up by syncvg command lslv ~ List Logical Volume
chfs -a freeze ~writes all dirty file system metadata and user data to the disk (use before BC & DR)
crfs –v jfs –d mylv –m /myfs
mount ~ mounts a filesystem
varyoffvg myvg ~ Deactivate Volume Group
exportvg myvg ~ Export Volume Group
importvg -y myvg -f /dev/hdisk9 ~ Import Volume Group
varyonvg myvg ~ Activate Volume Group
:: HP/UX HOST COMMANDS :: http://www.docs.hp.com/en/B2355-90681/index.html
HP/UX Software Installation
sysdef ~ analyzes current running system
swlist –l bundle ~ displays version and type of HP-UX
swlist -l patch ~ List installed patches
swreg –l depot /full/path/to/your/depot_file ~ Register a depot package for install
swinstall ~ Install the Software depot
HP/UX Device Commands
insf –e ~ install special device files
ioscan -fnC disk ~ scans system hardware
sam ~ System administration tool
dd if=/dev/rdsk/c34t15d0 of=/dev/zero count=1 ~ makes HP register with a Clariion thru LUNZ device
navicli –h <SP IP> register ~registers host with Clariion and tests agent install
lsdev –C disk ~ list device drivers in the system
mknod ~ makes a directory, special, or ordinary file
/stand/system ~ system configuration file
HP SAN Commands
fcmsutil /dev/fcd0 ~ List HBA wwn
tdutil /dev/td0 ~ List HBA wwn
HP iSCSI Commands
http://docs.hp.com/en/T1452-90011/T1452-90011.pdf
HP NFS Commands
/etc/exports ~file controls which file systems are exported to remote hosts and specify options
/exported/directory example.emc.com ~Exports directory to host example.emc.com (found in /etc/exports)
exportfs –a ~command to read /etc/export and export filesystem
mount shadowman.emc.com:/misc/export /misc/local ~mount an NFS export from shadowman.emc.com to the dir /misc/local
HP/UX Filesystem commands
pvcreate /dev/rdsk/c1t0d2 ~ creates a physical volume within a LVM volume group
pvdisplay ~ display info about physical volumes within an LVM volume group
ls -l /dev/*/group ~list the minor number of each vg in 6th field (all not listed are available)
mkdir /dev/myvg ~Create directory entry in /dev for Volume Group
mknod /dev/myvg/group c 64 0x010000 ~ Create a file for Volume Group
vgcreate -s 16 /dev/myvg /dev/dsk/c1t0d0 ~ creates a LVM volume group
vgextend /dev/myvg /dev/dsk/c1t0d1 ~ add disk to VG
vgchange -a y myvg ~ Avtivate VG
vgscan ~ scan physical volumes for LVM volume groups
vgdisplay ~ displays info about LVM volume groups
lvcreate -l 16 -n mylv /dev/myvg ~ creates LVM logical volumes
lvcreate -m mylv /dev/myvg ~ creates mirrored logical volumes
lvdisplay ~ displays LVM logical volumes
newfs /dev/myvg/rmylv ~ Create file system
mount /dev/myvg/mylv /myfs ~ Mount file system
vgchange -a n myvg ~ Deactivate Volume Group
vgexport myvg ~ Export Volume Group
vgimport /dev/myvg /dev/dsk/c1t0d0 ~ Import Volume Group
:: Linux HOST COMMANDS :: http://www.redhat.com/docs/manuals/enterprise/RHEL-5-manual/en-US/
Linux Software Installation
rpm –hiv
Linux Device Commands
modeinfo lpfc | grep parm ~Emulex hba parameters
modprobe -r lpfc ~unload Emulex driver
lsmod | grep lpfc ~
modprobe lpfc ~ discover new disk /sys/class/scsi_host/host1/issue_lip ~ discover new disk
dmesg |grep scsi ~list scsi devices
echo "- - -" > /sys/class/scsi_host/host0/scan ~ discover new disk
/sys/class/scsi_host/host1/scan ~ discover new disk
/usr/sbin/lpfc lun_scan all
Linux FC SAN Commands
hbacmd list ~list Emulex hba
hbacmd allnodeinfo xx:xx:xx:xx:xx:xx:xx:xx ~detail hba wwn info & device list
more /sys/class/scsi_host/hostX/port_name ~ wwn on RHEL4
more /sys/class/fc_host/hostX/port_name ~ wwn on RHEL5
Linux iSCSI Commands
yum install iscsi-initiator-utils ~install iSCSI soft initiator
rpm -q srvadmin-deng iscsi-initiator-utils ~install iSCSI soft initiator
rpm -ql iscsi-initiator-utils ~confiure iSCSI soft initiator
iscsi-iname ~discover iqn
iscsi-ls ~list adapters
iscsiadm -m discovery -t -p 192.168.1.100 ~discover iSCSI target
iscsiadm --mode node --targetname iqn ~
Linux NFS Commands
/etc/exports ~file controls which file systems are exported to remote hosts and specify options
/exported/directory example.emc.com ~Exports directory to host example.emc.com (found in /etc/exports)
exportfs –a ~command to read /etc/export and export filesystem
mount shadowman.example.com:/misc/export /misc/local ~mount an NFS export
Linux Filesystem commands http://linux.about.com/od/commands/l/blcmdl_8m.htm
pvcreate /dev/emcpowerX ~ initializes PhysicalVolume for later use by the Logical Volume Manager
vgcreate VG_Name /dev/emcpowerX ~ creates a new volume group
lvcreate --size 2000m --name LV_Name /dev/VG_Name ~creates 2000MB logical volume
mkfs -t ext2 /dev/VG_Name/LV_Name ~ Make a file system on a logical volume
mount -t ext2 /dev/VG_Name/LV_Name /mnt/FS_MountPoint ~ mount File system
df –a ~display filesystems
Fdisk /dev/sda ~ partition table manipulation
pvdisplay ~ allows you to see the attributes of one or more physical volumes
pvscan ~ scans all supported LVM block devices in the system for physical volumes
vgdisplay ~display attributes of volume groups
vgextend ~ allows you to add one or more initialized physical volumes
vgscan ~ scan physical volumes for LVM volume groups
vgexport ~make volume groups unknown to the system
vgimport ~make volume groups known to the system
lvdisplay ~display attributes of a logical volume lvextend ~ Extend logigal volume
fsck ~Command used to check and repair a Linux filesystem
:: SUN/SOLARIS HOST COMMANDS :: http://developers.sun.com/openstorage/articles/opensolaris_storage_server.html
SOLARIS Software Installation
ptree –a ~ Shows all running processes in a tree format
showrev –p ~ Displays currently installed Solaris patches
prtconf ~ prints system configurations
pkginfo ~ lists installed software packages
pkgadd ~ install software packages
pkgrm ~ removes installed software packages
Solaris Device Commands
cfgadm –a ~ list all
cfgadm –c configure c4 ~ configure StorEdge Leadville driver.(Search for new devices)
devfsadm –vC ~ searches for devices and also cleans up old
update_drv -f sd -d –I ~ searches for devices
drvconfig ~ generates special device files
isainfo –kv ~ list the architecture of the physical box.
reboot -- -r ~ reboots system to discover configuration changes, and rebuild special files
/etc/system ~ system files
/kernel/drv/sd.conf ~ lists of available target ids and luns
/kernel/drc/lpfc.conf ~ used for persistent binding on Emulex (qla22xx.conf for Qlogic)
/var/adm/messages ~ system messages
Solaris iSCSI Commands
iscsiadm add static-config iqn.1999-08.com.array:sn.01234567,192.168.1.3:3260 ~map target
iscsiadm add discovery-address 192.168.1.13:3260
iscsiadm modify discovery --isns enable
iscsiadm list target –vS Target: iqn.1986-03.com
devfsadm -Cv -i iscsi
Solaris FC SAN Commands
fcinfo hba-port ~ Lists information and WWNs
fcinfo remote-port -p 10000000c937694f –ls ~ Lists the remote-port information
fcadm create-fcoe-port -t nxge0 ~Creates a FCoE target port
Solaris NFS Commands
share -F nfs -d "Cartman dir" / share2
mount -F nfs cartman:/share2 /cartman
share -F nfs -o ro=sun.ucs.indiana.edu,rw=teak.uwsg.indiana.edu /reports ~ export (share) /reports
/etc/dfs/dfstab ~ file to edit to make a share permanent
shareall –F nfs ~ command to excute that will read /etc/dfs/dfstab and share to the network
SOLARIS Filesystem Commands *** Format and lable all devices before using zpool *** zpool create spoon c3t6d9 ~create & mounts storage pool named spoon and mounts it at /spoon (no slice #)
zpool create spoon mirror emcpower3c emcpower4c ~create a RAID1 storage pool mounted at /spoon
zpool destroy –f spoon ~destroy a zpool
zfs create spoon/fs ~creates ZFS file system spoon/fs, automatically mounted at /spoon/fs.
zpool list ~list pools
format ~ Disk partitioning and maintenance program
sysdef ~ Device Listing
prtvtoc ~ Disk Label
metadevadm ~ Checks device ID configuration.
metainit ~ Configures volumes.
metastat ~ Displays the status of volumes or hot spare pools.
metaset ~ Administers disk sets.
newfs –v ~ makes a UFS filesystem on disk drive or partition within a diskdrive
zfs snapshot pool/filesystem@Thursday ~Take a read-only snapshot of a file system
zfs rollback pool/filesystem@Thursday ~Rollback live filesystem to snapshot
:: SOLUTIONS ENABLER COMMANDS :: https://support.emc.com/products/2071
Commands to see devices
syminq ~ list all devides seen by host OS
syminq -cids ~ list Clariion devices
syminq hba –fibre ~ list HBA
syminq –pdevfile ~List the location of devices
sympd list ~ lists the Symmetrix devices that the host OS can see
symdev list pd ~ lists the Symmetrix devices that the host OS can see
symdisk
Symdev Commands
symdev list ~ list all devices on symm
symdev –sa –p list ~ list devices maped to that one FA
symdev list –noport ~ list devices not mapped to any FE ports
symdev list –clariion
symdev show 0123 -v ~ vebose listing of one device
Symcfg Commands
symcfg discover ~ discover the storage environment
symcfg list ~ list local and remote symmetrixes
symcfg list –FA all list ~ lists all fibre directors in a Symmetrix system
symcfg list -dir all -address -available ~ sid 6196 ~ returns the next available LUN address
symcfg list -lockn all ~ list of visible Symm exclusive locks
symcfg -sid <sid> -lockn 15 release ~ release a lock on a Symmetrix array.
Symconfigure Commands symconfigure –sid <sid> -f <filename> preview ~ checks file to make sure it is ok to exe
symconfigure –sid <sid> -f <filename> commit ~ makes the changes from file
symconfigure –sid <sid> -f <filename> prepare
Symmaskdb Commands
symmaskdb list devs ~ lists all devices accessible to an HBA on a specified Symmetrix system
symmaskdb remove ~ removes the meta member devices
symmaskdb backup ~ backs up a database to a specified file
symmaskdb init ~ deletes and creates a new VCMDB
symmaskdb list assignment ~lists deives already assigned
symmaskdb list no_assignment ~lists deives not yet assigned
Symaccess Commands
symaccess -sid <sid> -file <BackupFileName> backup ~
symaccess list hba -v ~
symaccess -sid <sid> list assignment -v ~
symaccess -sid <sid> list logins ~
symaccess create -name <GroupName> -type initiator -wwn <wwn> ~
symaccess create -name <GroupName> -type port -dirport <Dir>:<Port> ~
symaccess create -name <GroupName> -type storage devs <SymDevStart:SymDevEnd> ~
symaccess create view -name <GroupsAndViewName> -wwn ~
Symmask Commands
symmask add devs ~ adds a device to the list of devices that a WWN can access in the database
symmask remove devs ~ removes a device from the list of devices that a WWN can access in the database
symmask refresh ~ refresh vcmdb to all FA ports
symmask login ~ lists for each Fibre director which hosts and HBA’s are logged in to a Symmetrix system
symmask list HBA’s ~ lists the WWN of the Fibre HBAs on this host
symmask -sid <sid> -wwn 50060B000024F9F6 -dir 16C -p 1 set heterogeneous on HP_UX
Other SYMCLI Commands
symsan ~list ports and LUN WWNs seen from a specific Symmetrix director and port
symdg ~ creates/deletes/renames device groups
symld ~ addes & removes devices to a deivce group
symbcv ~ associates/disassociate BCV with device groups
symmir ~ performs (split/establish/restore) BCV mirror commands against device groups
symclone ~ performs (split/establish/restore/activate/terminate/recreate)
symsnap ~ performs (restore/activate/terminate/recreate)
symrdf ~ performs (split/establish/restore/failover/update/failback/suspend/resume) against RDF device groups
symcg ~ Performs operations on a Symmetrix RDF composite group
symrslv ~ Displays logical-to-physical mapping information about a logical object that is stored on a disk.
symstat ~ Displays statistics information about a Symmetrix, any or all directors, a device group, a disk, or a device.
symioctl ~ sends I/O control commands to application
:: VNX for BLOCK COMMANDS :: https://support.emc.com/docu47580_VNX_Command_Line_Interface_Reference_for_Block_5.33.pdf?language=en_US
aviseccli –h <SP IP> getsp ~ verify connectivity
naviseccli –h <SP IP> register ~registers host with Clariion and tests agent install
naviseccli –h <SP IP> storagegroup ~ list all info about existing groups
naviseccli –h <SP IP> getrg -lunlist ~ list all existing raid groups and LUNS
naviseccli –h <SP IP> getdisk ~ shows numbers of disks in storage array
naviseccli –h <SP IP> getrg <rg id> ~ shows the number of raid groups
naviseccli –h <SP IP> get lun <lun id> ~ lists all the disks
naviseccli –h <SP IP> storagegroup -list ~ displays storage groups
naviseccli –h <SP IP> getcache ~ shows the cache
naviseccli –h <SP IP> port –list –sp ~list all the SP port’s wwpn
naviseccli –h <SP IP> createrg ~create a raid group
naviseccli –h <SP IP> bind –rg –cap –aa ~bind a lun
naviseccli –h <SP IP> storagegroup –create –gname <name> ~ creates a new storage group
naviseccli –h <SP IP> storagegroup –addhlu –gname <name> -hlu <#> -alu <#> ~ assigns LUNs to storage group
naviseccli –h <SP IP> storagegroup –connecthost –host <hname> -gname <gname> ~ assigns host to storage group
:: VNX for FILE COMMANDS :: https://support.emc.com/docu47567_VNX_Command_Line_Interface_Reference_for_File_8.1.pdf?language=en_US
nas_server – list ~Lists Data Mover id, type,state, name, and slot number
server_standby server_<server #> -activate mover ~Manually fails over Data Mover to standby
o When failed over primary will be renamed to server_<primary#>.faulted server_<standby#>
o When failed over standby will be renamed to the server name it is replacing: server_<primary#>
server_standby server_<server#> -restore mover ~Manually fails back primary Data Mover from standby
server_version ALL ~Current code version on the Data Movers
server_cpu server_<server#> -reboot now ~ Reboots Data Mover
server_standby ALL –verify mover ~DM status
nas_server –info –all ~Detailed info on DM’s
nas_version ~Checks current code level on CS
/nas/sbin/cs_standby –failover ~Fails over CS0 from CS0 to CS1
/nasmcd/sbin/cs_standby –takeover ~Fails over CS0 from CS1 to CS1
/nasmcd/getreason ~Shows current status of Control Stations and Data Movers
watch /nasmcd/getreason ~monitor status of Control Stations and Data Movers evey 2 seconds (ctrl-C)
:: POWERPATH COMMANDS :: http://powerlink.emc.com/km/appmanager/km/secureDesktop?internalId=0b01406680025034
powermt ~ manage powerpath environment
powercf ~ configure powerpath devices
powermt display dev=all ~display PowerPath controlled devices
powermt check
powermt config
emcpreg ~ manage powerpath license registration
emcpupgrade ~ convert powerpath configuration files
:: INQ :: ftp://ftp.lss.emc.com/pub/symm3000/inquiry/
inq –h ~ list options and syntax
inq –mapinfo ~display target mapping info
inq –hba ~ display HBA info
inq –fibre ~display FC HBA info only
inq –iscsi ~display ISCSI HBA info only
inq –showvol ~ display Symmetrix Volume Number.
inq –parent ~display PowerPath and OS device relationship
inq –winvol ~ show Windows filesystems
inq -clariion ~ display CLARiiON device information (ALU & HLU)
inq –clar_wwn ~display wwn (UID) of VNX devices
inq –sym_wwn ~display symm dev wwn & serial number
inq -dev \\.\physicaldrive1 -page0 ~ Raw unformatted data on a single device
inq -dev \\.\physicaldrive21 -pagec0 ~Raw formatted info on a Clariion volume
