Diagnostics Commands - cisco.com Commands Thismoduleprovidescommandlineinterface(CLI)commandsforconfiguringdiagnosticsonyourrouter. …

Diagnostics Commands

This module provides command line interface (CLI) commands for configuring diagnostics on your router.

To use commands of this module, you must be in a user group associated with a task group that includesappropriate task IDs. If the user group assignment is preventing you from using any command, contact yourAAA administrator for assistance.

• diagnostic load, page 2

• diagnostic monitor, page 4

• diagnostic monitor interval, page 6

• diagnostic monitor syslog, page 8

• diagnostic monitor threshold, page 9

• diagnostic ondemand action-on-failure, page 11

• diagnostic ondemand iterations, page 13

• diagnostic schedule, page 14

• diagnostic start, page 17

• diagnostic stop, page 20

• diagnostic test-parameters, page 22

• diagnostic unload, page 24

• ping (administration EXEC), page 26

• show diag , page 31

• show diagnostic bootup level, page 41

• show diagnostic content, page 43

• show diagnostic ondemand settings, page 48

• show diagnostic result, page 49

• show diagnostic schedule, page 57

• show diagnostic status, page 59

• show run diagnostic monitor, page 61

Cisco IOS XR System Monitoring Command Reference for the Cisco CRS Router, Release 4.2.x OL-26517-02 1

diagnostic loadTo load an offline diagnostic image for integrated field diagnostics, use the diagnostic load command inAdmin EXEC modeSystem Admin EXEC mode.

diagnostic load location node-id [autostart {all| basic}]

Syntax Description Loads an offline diagnostic image for a specified location. The node-id argumentis entered in the rack/slot/module notation. All modules in the specified slot areloaded with the offline diagnostic image.

location node-id

(Optional) Starts running the diagnostic tests after the image has loaded. Thefollowing options are available:

• all—Runs all tests.

• basic—Runs basic tests

autostart {all | basic}

Command Default None

Command Modes Admin EXEC modeSystem Admin EXEC mode

Command History ModificationRelease

This command was introduced.Release 3.4.0

Usage Guidelines Use the diagnostic load command to load an offline diagnostic image used for integrated field diagnostics.Loading a diagnostic image places the specified card out of service.

The time it takes to load a diagnostic image varies depending on the card. Use the show platform commandto determine if the image has been loaded and if the card has been placed out of service.

The distributed route processor (DRP) does not support the automatic running of tests when the image isloaded for CPU0 and CPU1. After the diagnostic image is loaded, use the diagnostic start location node-idtest {id | all | basic | non-disruptive} command to execute the tests.

Note

For more information about running Cisco IOS XR diagnostics, refer to Cisco IOS XR Diagnostics.

Cisco IOS XR System Monitoring Command Reference for the Cisco CRS Router, Release 4.2.x2 OL-26517-02

Diagnostics Commandsdiagnostic load

Task ID OperationsTask ID

executediag

Examples The following example shows how to load an offline diagnostic image:

RP/0/RP0/CPU0:router# admin

RP/0/RP0/CPU0:router(admin)# diagnostic load location 0/0/CPU0 autostart basic

diagnostic load will bring requested slot out of service. [confirm(y/n)] yUser has confirmed diagnostic load requestPreparing UUT for Diagnostics software.Downloading IDS diagnostics image /pkg/ucode/hfr-diag-l3sp-fdiagsDownloading IDS diagnostics image /pkg/ucode/hfr-diag-l3-fdiagsPlease wait for UUT image downloading ...diagnostic load in progress.

Related Commands DescriptionCommand

Displays information and status of each node in thesystem.

show platform


Diagnostics Commandsdiagnostic load

diagnostic monitorTo configure the health-monitoring diagnostic testing for a specified location, use the diagnostic monitorcommand in administration configuration mode. To remove the specified command from the configurationfile and restore the system to its default condition, use the no form of this command.

diagnostic monitor location node-id test {id| test-name} [disable]

no diagnostic monitor location node-id test {id| test-name} [disable]

Syntax Description Location to enable diagnostic monitoring. The node-id argument is entered in therack/slot/module notation.

node-id

Specifies diagnostic test selection. The following test selections are available:

• id—Test ID, as shown in the show diagnostic content command .

• test-name—Name of the test.

Use the show diagnostic content command in administration EXEC mode to seea list of test names and their associated IDs.

test {id | test-name}

Disables diagnostic monitoring for a specified location.disable

Command Default To view the default value for each test, use the show diagnostic content command in administration EXECmode when the diagnostic image is first installed. The default may be different for each test.

Command Modes Administration configuration



Usage Guidelines Use the diagnostic monitor command to enable or disable health-monitoring diagnostic testing for a specifiedtest at the specified location.

Use the disable keyword to disable a health-monitoring diagnostic test that is enabled by default. For example,if test 1 is enabled by default, the disable keyword disables the diagnostic test. If the no form of the commandis used, the test is set to the default condition, which is enabled.


Diagnostics Commandsdiagnostic monitor

To specify a node using the node-id argument, use the rack/slot/module notation. For example, 0/0/CPU0is a fully qualified location specification for a line card, 0/2/CPU0 is a fully qualified location specificationfor a line card, 0/7/CPU0 is a fully qualified location specification for a line card, 0/RSP0/CPU0 is a fullyqualified location specification for a Route Switch Processor.

Note

To specify a physical layer interface module (PLIM) node using the node-id argument, use the followingnotation: rack/PLslot-number/SP. For example, 0/PL1/SP. PLIM diagnostic tests are supported.

Note


read, writediag

Examples The following example shows how to enable health-monitoring diagnostic testing for 0/1/cpu0:

RP/0/0RP0RSP0/CPU0:router:hostname(admin-config)# diagnostic monitor location 0/1/cpu0 test1


Displays test information including test ID, test attributes, andsupported coverage test levels for each test and for all components.

show diagnostic content, on page 43


Diagnostics Commandsdiagnostic monitor

diagnostic monitor intervalTo configure the health-monitoring diagnostic testing for a specified interval for a specified location, use thediagnostic monitor interval command in administration configuration mode. To remove the specifiedcommand from the configuration file and restore the system to its default condition, use the no form of thiscommand.

diagnostic monitor interval location node-id test {id| test-name} number-of-days hour : minutes : seconds. milliseconds

no diagnostic monitor interval location node-id test {id| test-name} number-of-days hour :minutes : seconds. milliseconds

Syntax Description Specifies a location. The node-id argument is entered in therack/slot/module notation.

location node-id

Specifies diagnostic test selection. The following test selections areavailable:

• id—Test ID.

• test-name—Test name , as shown in the show diagnostic contentcommand..

Use the show diagnostic content command in administration EXECmode to see a list of test names and their associated IDs.


Interval between each test run.

The number-of-days argument specifies the number of days betweentesting. The range is from 0 through 20.

The hour:minutes:seconds.milliseconds argument specifies the interval,where hour is a number in the range from 0 through 23, minutes is anumber in the range from 0 through 59, seconds is a number in the rangefrom 0 through 59, and milliseconds is a number in the range from 0through 999.

number-of-dayshour:minutes:seconds.milliseconds

Command Default To view the default value for each test, use the show diagnostic content command in administration EXECmode when the diagnostic image is first installed. The default may be different for each test.





Diagnostics Commandsdiagnostic monitor interval

ModificationRelease


Usage Guidelines Use the diagnostic monitor interval command to set the health-monitoring interval of a specified test at thespecified location. The no version of the command resets the interval to the default setting. The diagnosticmonitor command is used to enable health-monitoring.

To specify a node using the node-id argument, use the rack/slot/module notation. For example, 0/0/CPU0is a fully qualified location specification for a line card, 0/2/CPU0 is a fully qualified location specificationfor a line card, 0/7/CPU0 is a fully qualified location specification for a line card, 0/RSP0/CPU0 is a fullyqualified location specification for a Route Switch Processor, and 0/RSP0/CPU0 is also a fully qualifiedlocation specification for a Route Switch Processor.

Note


Note


read, writediag

Examples The following example shows how to set the health-monitoring diagnostic testing at an interval of 1 hour, 2minutes, 3 seconds, and 4 milliseconds for 0/1/cpu0:

RP/0/0RP0RSP0/CPU0:router:hostname(admin-config)# diagnostic monitor interval location0/1/cpu0 test 1 0 1:2:3.4


Configures the health-monitoring diagnostic testing for a specifiedlocation.

diagnostic monitor, on page 4




Diagnostics Commandsdiagnostic monitor interval

diagnostic monitor syslogTo enable the generation of a syslog message when any health monitoring test fails, use the diagnostic monitorsyslog command in administration configuration mode. To remove the specified command from theconfiguration file and restore the system to its default condition, use the no form of this command.

diagnostic monitor syslog

no diagnostic monitor syslog

Syntax Description This command has no keywords or arguments.

Command Default Syslog is disabled.





Usage Guidelines Use the diagnostic monitor syslog command to enable the generation of a syslog message when ahealth-monitoring test fails.


read, writediag

Examples The following example shows how to enable the generation of syslog messages:

RP/0/0RP0RSP0/CPU0:router:hostname(admin-config)# diagnostic monitor syslog





Diagnostics Commandsdiagnostic monitor syslog

diagnostic monitor thresholdTo configure the health-monitoring diagnostic testing failure threshold, use the diagnostic monitor thresholdcommand in administration configuration mode. To remove the specified command from the configurationfile and restore the system to its default condition, use the no form of this command.

diagnostic monitor threshold location node-id test {id| test-name} failure count failures

no diagnostic monitor threshold location node-id test {id| test-name} failure count failures

Syntax Description Specifies a location. The node-id argument is entered in the rack/slot/modulenotation.

location node-id

Specifies diagnostic test selection. The following test selections are available:

• id—Test ID.

• test-name—Test name , as shown in the show diagnostic contentcommand. .

Use the show diagnostic content command in administration EXEC modeto see a list of test names and their associated IDs.


Specifies the number of allowable test failures. Range is 1 to 99.failure count failures

Command Default To view the default value for each test, use the show diagnostic content command in administration EXECmode when the diagnostic image is first installed. The default can be different for each test.





Usage Guidelines Use the diagnostic monitor threshold command to specify health-monitoring diagnostic testing failurethreshold.


Diagnostics Commandsdiagnostic monitor threshold


Note


Note


read, writediag

Examples The following example shows how to set the failure threshold to 35 test failures for test 1 all tests for 0/1/cpu0:

RP/0/0RP0RSP0/CPU0:router:hostname(admin-config)# diagnostic monitor threshold location0/1/cpu0 test 1 all failure count 35





Diagnostics Commandsdiagnostic monitor threshold

diagnostic ondemand action-on-failureTo set when to stop test execution for a diagnostic start command, use the diagnostic ondemandaction-on-failure command in Admin EXEC modeSystem Admin EXEC mode. This command is used inconjunction with the diagnostic ondemand iteration command.

diagnostic ondemand action-on-failure {continue failure-count| stop}

diagnostic ondemand action-on-failure {continue [ failure-count ]| stop}

Syntax Description Specifies that test execution continue until the number of failures reaches thespecified failure-count. Range is 0 to 65534. A failure-count of 0 indicates to notstop execution until all iterations are complete, no matter how many failures areencountered.

continue failure-count

Stops execution immediately when the first test failure occurs.stop

Syntax Description Specifies that test execution continues until all iterations are complete, no matter howmany failures are encountered.

continue

(Optional) Specifies that test execution continues until the number of failures reachesthe specified failure-count. Range is 0 to 65534. A failure-count of 0 indicates to notstop execution until all iterations are complete, no matter how many failures areencountered.

failure-count

Stops execution immediately when the first test failure occurs.stop

Command Default failure-count: 0





Usage Guidelines Use the diagnostic ondemand action-on-failure command to specify whether or when to stop test executionif a test fails. This command is used in conjunction with the diagnostic ondemand iterations command.


Diagnostics Commandsdiagnostic ondemand action-on-failure


read, writeexecutediag

Examples The following example shows how to set the test failure action to stop:

RP/0/0RP0RSP0/CPU0:router:hostname(admin)# diagnostic ondemand action-on-failure stop


Sets the number of times to repeat execution of thediagnostic test.

diagnostic ondemand iterations, on page 13

Runs a specified diagnostic test.diagnostic start, on page 17


Diagnostics Commandsdiagnostic ondemand action-on-failure

diagnostic ondemand iterationsTo set the number of times to repeat execution of the tests specified by the diagnostic start command, usethe diagnostic ondemand iterations command in Admin EXEC modeSystem Admin EXEC mode.

diagnostic ondemand iterations count

Syntax Description Number of times to repeat the specified on-demand tests. Range is 1 to 999.count

Command Default count: 1





Usage Guidelines Use the diagnostic ondemand iterations command to specify the number of times the specified on-demandtests run. The on-demand tests are specified using the diagnostic start command.


read, write executediag

Examples The following example shows how to set the number of iterations to 12:

RP/0/0RP0RSP0/CPU0:router:hostname(admin)# diagnostic ondemand iterations 12


Sets when to stop test execution for a diagnostic test.diagnostic ondemand action-on-failure, on page 11



Diagnostics Commandsdiagnostic ondemand iterations

diagnostic scheduleTo configure a diagnostic schedule, use the diagnostic schedule command inAdminConfigurationmodeSystemAdmin Config mode. To disable the diagnostic schedule, use the no form of this command.

diagnostic schedule location node-id test {id| test-name| all| basic| complete| minimal| non-disruptive|per-device} [device number| all] {daily| on month day year| weekly day-of-week} hour:minute

no diagnostic schedule location node-id test {id| test-name| all| basic| complete| minimal| non-disruptive|per-device} [device number| all] {daily| on month day year| weekly day-of-week} hour:minute

diagnostic schedule location node-id test {id| all| non-disruptive} {daily| on month day year| weeklyday-of-week} hour:minute

no diagnostic schedule location node-id test {id| all} {daily| on month day year| weekly day-of-week}hour:minute

Syntax Description Schedules a diagnostic test for a specified location. The node-id argument isentered in the rack/slot/module notation.

location node-id

Specifies a specific diagnostic test, or all diagnostic tests.test

Test ID or list of test IDs, as shown in the show diagnostic content command.Multiple tests can be listed if separated by semicolons (;) and a range of datescan be listed if separated by a hyphen (-), as follows:

• x;y-z (for example: 1; 3-4 or 1;3;4)

id

Specifies all tests.all

Specifies the nondisruptive test suite [Attribute = N].non-disruptive

Specifies a daily schedule.daily

Schedules an exact date.on month day year

Specifies a weekly schedule with a set day of the week. Enter the name of a dayof the week or a number that specifies a day of the week in the range from 0through 6, where 0 is today.

weekly day-of-week

Scheduled start time, where hour is a number in the range from 0 through 23,and minute is a number in the range from 0 through 59.

hour:minute

Syntax Description Schedules a diagnostic test for a specified location. The node-id argument isentered in the rack/slot/module notation.

location node-id



Diagnostics Commandsdiagnostic schedule

Specifies a test ID or list of test IDs. Use the show diagnostic content commandin administration EXECmode to see a list of test names and their associated IDs.Multiple tests can be listed if separated by semicolons (;) as follows:


id

Specifies the name of a test. Use the show diagnostic content command inadministration EXEC mode to see a list of test names.

test-name


Specifies the basic on-demand test suite [Attribute = B].basic

Specifies the complete bootup test suite [Attribute = C].complete

Specifies the minimal bootup test suite [Attribute = M].minimal

Specifies the non-disruptive test suite [Attribute = N].non-disruptive

Specifies the per-device test suite [Attribute = V].per-device

This string works only with the all, basic, complete, minimal,non-disruptive, and per-device keywords.

Note

(Optional) Specifies the devices on which the diagnostic tests should run. Thefollowing options are available:

• number—Runs tests on one or more devices. The range is 1 through 8. Tospecify multiple devices, you can use hyphens (-) and semicolons (;); forexample, 1; 3-4 or 1;3;4).

• all—Runs tests on all devices.

device number | all

Specifies a daily schedule.daily

Schedules an exact date.on month day year

Specifies a weekly schedule with a set day of the week. Enter the name of a dayof the week or a number that specifies a day of the week in the range from 0through 6.

weekly day-of-week

Scheduled start time, where hour is a number in the range from 0 through 23,and minute is a number in the range from 0 through 59.

hour:minute

Command Default No default behavior or values

Command Modes Admin Configuration modeSystem Admin Config mode






Usage Guidelines


Note


Note



read, writediag

Examples The following example shows how to schedule a diagnostic test:

The following example shows how to schedule all diagnostic tests for location 0/0/CPU0 every day at 12:30pm:

RP/0/0RP0RSP0/CPU0:router:hostname# adminRP/0/0RP0RSP0/CPU0:router:hostname(admin)# configureRP/0/0RP0RSP0/CPU0:router:hostname(admin-config)# diagnostic schedule location 0/0/CPU0test all daily 12:30

The following example shows how to schedule all bootup tests for device 1 every Sunday at 12:30 pm:

RP/0/0RP0RSP0/CPU0:router:hostname# adminRP/0/0RP0RSP0/CPU0:router:hostname(admin)# configureRP/0/0RP0RSP0/CPU0:router:hostname(admin-config)# diagnostic schedule location 0/0/CPU0test all daily complete device 1 weekly 12:30


Displays the current scheduled diagnostic tasks.show diagnostic schedule, on page 57



diagnostic startTo run a specified diagnostic test, use the diagnostic start command in Admin EXEC modeSystem AdminEXEC mode.

diagnostic start location node-id test {id| test-name| all| basic| complete| minimal| non-disruptive|per-device} [device number| all]

diagnostic start location node-id test {id| all| non-disruptive}

Syntax Description Runs diagnostic testing for a specified location. The node-id argument is enteredin the rack/slot/module notation.

location node-id


Test ID or list of test IDs, as shown in the show diagnostic content command.Multiple tests can be listed if separated by semicolons (;) a range of dates can belisted if separated by a hyphen (-), as follows:


id



Syntax Description Runs diagnostic testing for a specified location. The node-id argument is enteredin the rack/slot/module notation.

location node-id


Test ID or list of test IDs. Use the show diagnostic content command inadministration EXEC mode to see a list of test names and their associated IDs.Multiple tests can be listed if separated by semicolons (;) as follows:


id

Name of the test. Use the show diagnostic content command in administrationEXEC mode to see a list of test names.

test-name


Specifies the basic on-demand test suite [Attribute = B].basic

Specifies the complete bootup test suite [Attribute = C].complete

Specifies the minimal bootup test suite [Attribute = M].minimal


Diagnostics Commandsdiagnostic start


Specifies the per-device test suite [Attribute = V].per-device

This string works only with the all, basic, complete, minimal,non-disruptive, and per-device keywords.

Note

(Optional) Specifies the devices on which the diagnostic tests should start. Thefollowing options are available:

• number—Start tests on one or more devices. The range is 1 through 8. Tospecify multiple devices, you can use hyphens (-) and semicolons (;); forexample, 1; 3-4 or 1;3;4).

• all—Starts tests on all devices.

device number | all





The per-device keyword was added.Release 3.5.0


Usage Guidelines Use the diagnostic start command to run a diagnostic test on a specified card.


Note


Note





executediag

Examples The following example shows how to start a suite of basic diagnostic tests for a specified location:

RP/0/0RP0RSP0/CPU0:router:hostname# adminRP/0/0RP0RSP0/CPU0:router:hostname(admin)# diagnostic start location 0/0/CPU0 test basic

The following example shows how to start a suite of minimal bootup tests for devices 1 through 7 at thespecified location:

RP/0/0RP0RSP0/CPU0:router:hostname# adminRP/0/0RP0RSP0/CPU0:router:hostname(admin)# diagnostic start location 0/0/CPU0 test minimaldevices 1-7

The following example shows how to run a complete suite of diagnostic tests for a specified location:

RP/0/0RP0RSP0/CPU0:router:hostname# adminRP/0/0RP0RSP0/CPU0:router:hostname(admin)# diagnostic start location 0/0/CPU0 test all


Stops the diagnostic testing in progress on a node.diagnostic stop, on page 20



diagnostic stopTo stop the diagnostic testing in progress on a node, use the diagnostic stop command in Admin EXECmodeSystem Admin EXEC mode.

diagnostic stop location node-id

Syntax Description Stops diagnostic testing for a specified location. The node-id argument isentered in the rack/slot/module notation.

location node-id






Usage Guidelines Use the diagnostic stop command to stop a diagnostic test on a specified node. The command is used forscheduled tests, a test that is causing errors, or a test that does not finish.


Note


Note



executediag


Diagnostics Commandsdiagnostic stop

Task ID

Examples The following example shows how to stop the diagnostic test process:

RP/0/0RP0RSP0/CPU0:router:hostname# adminRP/0/0RP0RSP0/CPU0:router:hostname(admin)# diagnostic stop location 0/0/CPU0




Diagnostics Commandsdiagnostic stop

diagnostic test-parametersThe FabricUcastMcastTest diagnostic test is used to periodically verify the fabric connectivity to all fabricdestinations (RP, LC, DRP nodes) in a single or multi-chassis system. Automatic reload and shutdown as aresult of a single -node failure is disabled by default. To enable this feature, set the parameters of theFabricUcastMcast test by setting one or more of the optional parameters of the diagnostic test-parametersFabricUcastMcastTest command in Admin EXEC modeSystem Admin EXEC mode.

diagnostic test-parametersFabricUcastMcastTest[single-DRP-node-failure|single-LC-node-failure|single-RP-node-failure]<failure-type|reload threshold | shutdown threshold>

Syntax Description (Optional) Enters the mode to set the parameters for the FabricUcastMcast Testwhen a single node failure occurs as a result of a DRP failure.

single-DRP-node-failure

(Optional) Enters the mode to set the parameters for the FabricUcastMcast Testwhen a single node failure occurs as a result of a line card (LC) failure.

single-LC-node-failure

(Optional) Enters the mode to set the parameters for the FabricUcastMcast Testwhen a single node failure occurs as a result of a route processor (RP) failure.

single-RP-node-failure

(Optional) Specifies the type of ping result to use for triggering node reload orshutdown. Options are:

• unicast-only-Multicast ping results are ignored.

• multicast-only-Unicast ping results are ignored.

Default is both unicast and multicast ping results are used.

failure-type

(Optional) Specifies the number of consecutive single-node failures that triggerthe reload of a node. Range is 2 through 255. This value must be less than theshutdown threshold for the same node type.

reload threshold

(Optional) Specifies the number of consecutive single-node failures that triggerthe shutdown of a node. Range is 2 through 255. This value must be greater thanthe reload threshold for the same node type.

shutdown threshold

Command Default None





Diagnostics Commandsdiagnostic test-parameters

Usage Guidelines No specific guidelines impact the use of this command.


read, writediag

Examples The following example shows how to set a node for automatic reload and shutdown when theFabricUcastMcastTest results return single node failure. This is a result of line card failures for only multicasttraffic:

RP/0/RP0/CPU0:router# adminRP/0/RP0/CPU0:router(admin)# configurationRP/0/RP0/CPU0:router(admin-config)# diagnostic test-parametersRP/0/RP0/CPU0:router(admin-config-diag-test-params)#FabricUcastMcastTestRP/0/RP0/CPU0:router(admin-config-FabricUcastMcastTest)#single-LC-node-failureRP/0/RP0/CPU0:router(admin-config-FabricUcastMcastTest-LC)failure-type multicast-onlyRP/0/RP0/CPU0:router(admin-config-FabricUcastMcastTest-LC)reload threshold 5RP/0/RP0/CPU0:router(admin-config-FabricUcastMcastTest-LC)shutdown threshold 6RP/0/RP0/CPU0:router(admin-config-FabricUcastMcastTest-LC)commitWhen a single-node failure is detected, the following syslog messages are logged:RP/0/RP1/CPU0:Jan 27 07:58:58.364 : online_diag_rp[276]: %DIAG-XR_DIAG-3-ERROR : (U)Fabric Ping Failure, 1 of 3 nodes failed(L): 0/3/CPU0RP/0/RP1/CPU0:Jan 27 07:58:58.802 : online_diag_rp[276]: %DIAG-XR_DIAG-3-ERROR : (U) FIM:

single-node failure detected - 0/3/CPU0consecutive ucast/mcast failures: 15/0

When the reload threshold is reached, the following syslog message is logged prior to the reload:RP/0/RP1/CPU0:Jan 27 07:58:58.803 : online_diag_rp[276]: %DIAG-XR_DIAG-6-INFO :reloadthreshold 15 crossed, reloading 0/3/CPU0

When the shutdown threshold is reached, the following syslog messages are logged:RP/0/RP1/CPU0:Jan 27 08:11:02.104 : online_diag_rp[276]: %DIAG-XR_DIAG-6-INFO : shutdownthreshold 10 crossed, shutting down 0/3/CPU0RP/0/RP1/CPU0:Jan 27 08:11:02.137 : online_diag_rp[276]:%PLATFORM-SHELFMGR-6-BRINGDOWN_REQUEST_LIB : Requesting node 0/3/CPU0 to be shutdown.reason: [diag fabric ping failure]RP/0/RP0/CPU0:Jan 27 08:11:02.136 : shelfmgr[306]: %PLATFORM-SHELFMGR-6-BRINGDOWN_REQUEST

: process online_diag_rp running on node0_RP1_CPU0 requested node 0/3/CPU0 to be shutdown.

reason: [diag fabric ping failure]


Diagnostics Commandsdiagnostic test-parameters

diagnostic unloadTo unload an offline diagnostic image, use the diagnostic unload command in Admin EXEC modeSystemAdmin EXEC mode.

diagnostic unload location node-id

Syntax Description Unloads an offline diagnostic image for a specified location. The node-id argumentis entered in the rack/slot/module notation. The diagnostic image is unloaded forall modules in the specified slot.

location node-id





Usage Guidelines Use the diagnostic unload command to unload an offline diagnostic image used for integrated field diagnostics.Unloading the image returns the specified card to service.

Use the show platform command to determine if the card has been placed back into service.



executediag

Examples The following example shows how to unload a diagnostic image:

RP/0/0RP0RSP0/CPU0:router:hostname# adminRP/0/0RP0RSP0/CPU0:router:hostname(admin)# diagnostic unload location 0/0/CPU0


Diagnostics Commandsdiagnostic unload


Loads a diagnostic test.diagnostic load, on page 2

Displays information and status of each node in thesystem.

show platform


Diagnostics Commandsdiagnostic unload

ping (administration EXEC)To send internal echo messages from one node to another, use the ping command in administration EXECmode.

ping {control-eth| fabric} {fgid id| location node-id} [count pings] [debug] [intervalmilliseconds] [patternrandom] [queue priority] [retries number] [size payload_size] [timeout seconds] [tlate seconds] [uc][via-egressq] [via-fabricq-1]

Syntax Description Specifies a control ethernet ping test.control-eth

Specifies a fabric ping test.fabric

Specifies that a multicast ping is sent over a fabric to nodes with the fabric groupidentifier (FGID) of 1024 through 1000000. Nodes that receive the ping respond witha unicast packet.

fgid id

Specifies that a unicast ping is sent a node. The node-id argument is entered in therack/slot/module notation.

location node-id

(Optional) Number of pings to send each time the command is run. The test reportsresults and statistics after all pings have been sent and received (or timed out). Rangeis from 0 through 4294967295. The default is 1.

count pings

This keyword is available only if you specified the fgidkeyword.

Note

(Optional) Specifies verbose debugging of the multicast ping utility.

debug

(Optional) Hold-off time between each ping in milliseconds. Range is from 0 through4294967295. The total test time is as follows:

(count-1) * (RTT + interval) + RTT

RTT = Round Trip Time for the ping.

interval milliseconds

(Optional) Specifies a data pattern for the ping packet payload.pattern random


Note

(Optional) Specifies the priority of the queue. The priority can be 0 or 1.

queue priority

(Optional) Maximum number of times a failed ping transmission is sent before thepacket transmission is considered a failure. Range is from 0 through 4294967295.

Packet transmission failure is usually an indication of a server softwaretransient. In this case, we recommend that you run the ping command again.

Note

retries number

(Optional) Specifies the payload size for each ping packet size. Range is from 0through 4294967295 bytes. The maximum payload size allowed may be limited,depending on the transport type that is used (fabric or control-ethernet).

size payload_size


Diagnostics Commandsping (administration EXEC)

(Optional) Specifies the maximum time to wait for response to a ping. Range is from0 through 4294967295 seconds.

If a ping does not receive a response before the configured timeout expires, the pingstatistics reflect it as a discrepancy between the “Sent:” and “Rec'd:” packet count, andthe test is considered failed. Because of this, we recommend that you do not set thetimeout to 0.

timeout seconds


Note

(Optional) Specifies the amount of time to wait for a response to a multicast ping.The amount of time you specify must be less than the value of the timeout keyword.Range is from 0 through 4294967295 seconds.

tlate seconds


Note

(Optional) Specifies that unicast pings (instead of multicast pings) are sent to nodeswith the specified FGID.

uc

(Optional) Specifies that a unicast or multicast ping packet is routed to the first fabricqASIC (instance 0); then, to the egressq ASIC, and finally to the destination CPU.

By default, a unicast ping is routed to the first fabricq ASIC (instance 0), then to thedestination CPU. Amulticast ping is routed to the constituent fabricq ASIC instances,then to the destination CPU.

via-egressq

This keyword is available if you specified the location keyword, or both thefgid and uc keywords.

Note

(Optional) Specifies that a unicast ping is routed to the current fabricq ASIC (instance1), then to the egressq ASIC, and finally, to the destination CPU.

By default, a unicast ping is routed to the first fabricq ASIC (instance 0), then to thedestination CPU.

via-fabricq-1


Command Modes Administration EXEC



The fgid keyword was added.Release 3.6.0

The via-egressq and via-fabricq-1 keywords were added.Release 3.8.0



Usage Guidelines When you enter the ping command, a ping is sent to the node at the specified location or to nodes with thespecified FGID. The received response is compared byte-by-byte to the sent packet. If a ping response is notreceived before the specified time-out, or if the ping response does not match the transmitted ping, the pingis considered failed.

A node that is unreachable or intermittently working impacts the total run time for the test as follows:

(received_packet_count * RTT + lost_packet_count * timeout + (count-1) * interval)

Line cards have two fabricq ASICs and an egressq ASIC. From the first fabricq ASIC (instance 0), the CPUcan be reached directly or via the egressq ASIC. From the second fabricq ASIC (instance 1), the CPU can bereached only via the egressq ASIC. In other words, no direct packet path exists between instance 1 and theCPU.

The route processor (RP) and distributed route processor (DRP) cards have only one fabricq ASIC per node(CPU) and no egressq ASIC. Therefore, a fabric ping on an RP or DRP destination specified with thevia-egressq or via-fabricq-1 keyword fails.


executediag

Examples The following example shows sample output from a control-ethernet ping to an SP node in slot 0/0:

RP/0/0RP0RSP0/CPU0:router:hostname# adminRP/0/0RP0RSP0/CPU0:router:hostname(admin)# ping control-eth location 0/0/SP count 5

Src node: 529 : 0/RP0/CPU0Dest node: 0 : 0/0/SPLocal node: 529 : 0/RP0/CPU0Packet cnt: 5 Packet size: 128 Payload ptn type: default (0)Hold-off (ms): 300 Time-out(s): 2 Max retries: 5Destination node has MAC addr 5246.4800.0000

Running CE node ping.Please wait...Src: 529:, Dest: 0, Sent: 5, Rec'd: 5, Mismatched: 0Min/Avg/Max RTT: 0/200/1000CE node ping succeeded for node: 0

The following example shows a fabric ping from the active RP to the active RP. In this example, the pingcontains 72 packets of 1 kilobyte each. This command performs a good coverage test of the entire switchfabric:

RP/0/0RP0RSP0/CPU0:router:hostname# adminRP/0/0RP0RSP0/CPU0:router:hostname(admin)# ping fabric location 0/RP0/CPU0 count 72 size1024

Src node: 529 : 0/RP0/CPU0Dest node: 529 : 0/RP0/CPU0Local node: 529 : 0/RP0/CPU0Packet cnt: 72 Packet size: 1024 Payload ptn type: default (0)Hold-off (ms): 300 Time-out(s): 2 Max retries: 5

Running Fabric node ping.



Please wait...Src: 529:, Dest: 529, Sent: 72, Rec'd: 72, Mismatched: 0Min/Avg/Max RTT: 3000/3013/4000Fabric node ping succeeded for node: 529

The following example shows a ping to a control Ethernet node that has a problem or does not exist:

RP/0/0RP0RSP0/CPU0:router:hostname# adminRP/0/0RP0RSP0/CPU0:router:hostname(admin)# ping control-eth location 0/1/CPU0 count 3

Src node: 529 : 0/RP0/CPU0Dest node: 17 : 0/1/CPU0Local node: 529 : 0/RP0/CPU0Packet cnt: 3 Packet size: 128 Payload ptn type: default (0)Hold-off (ms): 300 Time-out(s): 2 Max retries: 5Destination node has MAC addr 5246.4800.0011

Running CE node ping.Please wait...Src: 529:, Dest: 17, Sent: 3, Rec'd: 0, Mismatched: 0Requested ping failed for node: 17

The following example shows how to send a multicast fabric ping to nodes with the FGID of 1024. The nodethat sent the multicast ping waits 1 second for a response from each node.

RP/0/0RP0RSP0/CPU0:router:hostname# adminRP/0/0RP0RSP0/CPU0:router:hostname(admin)# ping fabric fgid 1024 tlate 1

Src node: 513 : 0/RP0/CPU0fgid: 1024Local node: 513 : 0/RP0/CPU0Packet cnt: 1 Packet size: 128 Payload ptn type: default (0)Hold-off (ms): 1 Time-out(s): 2 Max retries: 5DelayTimeout: 1 Priority: HighRunning Fabric node ping.Please wait...

Multicast (Pinging fgid) ...

Node Sent Rcv. Late Lost______________________________________________________________0/1/CPU0 (0x11:17) 1 1 0 00/4/CPU0 (0x41:65) 1 1 0 00/4/CPU1 (0x42:66) 1 1 0 00/6/CPU0 (0x61:97) 1 1 0 0

0/RP0/CPU0 (0x201:513) 1 1 0 00/RP1/CPU0 (0x211:529) 1 1 0 0

diag_ping: All 6 nodes responded to all 1 pings

The following example shows how to send a multicast fabric ping to nodes with the FGID of 1024. The pingpackets are routed from the first fabricq ASIC (instance 0) to the destination CPU via the egressq ASIC. Thepings to the two line cards (0/1/CPU0 and 0/6/CPU0) succeeded, while the pings to the RPs (0/RP0/CPU0and 0/RP1/CPU0) and DRPs (0/4/CPU0 and 0/4/CPU1) failed because they do not have an egressq ASIC.

RP/0/0RP0RSP0/CPU0:router:hostname# adminRP/0/0RP0RSP0/CPU0:router:hostname(admin)# ping fabric fgid 1024 count 10 via-egressq

Src node: 513 : 0/RP0/CPU0fgid: 1024Local node: 513 : 0/RP0/CPU0Packet cnt: 10 Packet size: 128 Payload ptn type: default (0)Hold-off (ms): 1 Time-out(s): 2 Max retries: 5DelayTimeout: 1 Priority: HighReaching destination CPUs via egressq

Running Fabric node ping.Please wait...



Multicast (Pinging fgid) ...


0/RP0/CPU0 (0x201:513) 10 0 0 100/RP1/CPU0 (0x211:529) 10 0 0 10

diag_ping: Out of 6 node(s), 2 node(s) responded to all 10 pings, 4 node(s) hads

The following example shows how to send a unicast ping to nodes with the FGID of 1024. The ping packetsare routed from the second fabricq ASIC (instance 1) to the destination CPU via the egressq ASIC. The pingsto the two line cards (0/1/CPU0 and 0/6/CPU0) succeeded, while the pings to the RPs (0/RP0/CPU0 and0/RP1/CPU0) and DRPs (0/4/CPU0 and 0/4/CPU1) failed because they do not have a second fabricq ASICnor an egressq ASIC.

RP/0/0RP0RSP0/CPU0:router:hostname# adminRP/0/0RP0RSP0/CPU0:router:hostname(admin)# ping fabric fgid 1024 count 10 uc via-fabricq-1

Src node: 513 : 0/RP0/CPU0fgid: 1024Local node: 513 : 0/RP0/CPU0Packet cnt: 10 Packet size: 128 Payload ptn type: default (0)Hold-off (ms): 1 Time-out(s): 2 Max retries: 5DelayTimeout: 1 Priority: HighUsing other fabricq instance

Running Fabric node ping.Please wait...

Multicast (Pinging Individual Sponge Ids) ...


0/RP0/CPU0 (0x201:513) 10 0 0 100/RP1/CPU0 (0x211:529) 10 0 0 10

diag_ping: Out of 6 node(s), 2 node(s) responded to all 10 pings, 4 node(s) hads



show diagTo display details about the hardware and software on each node in a router, use the show diag command inthe appropriate mode.

EXEC Mode

show diag [ node-id ] [details| eeprom-info| power-regs| summary]

Administration EXEC Mode

show diag [ node-id ] [chassis| fans| power-supply] [details| eeprom-info| power-regs| summary]

show diag [ node-id ] [chassis-info| details| summary]

EXEC Mode

show diag [ node-id ] [details| eeprom-info| power-regs| summary]

Administration EXEC Mode

show diag [ node-id ] [chassis| fans| power-supply] [details| eeprom-info| power-regs| summary]

Syntax Description (Optional) Identifies the node whose information you want to display. Thenode-id argument is expressed in the rack/slot/module notation.

Follow the node-id argument with one of the following optional keywords tospecify specific test results:

• details

• eeprom-info

• power-regs

• summary

node-id

(Optional) Displays detailed diagnostics information for the current node.details

(Optional) Displays field diagnostics results from the EEPROM.eeprom-info

(Optional) Displays field diagnostics results from the power registers.power-regs

(Optional) Displays summarized diagnostics results for all nodes in the system.summary

(Optional) Displays information about the chassis.chassis-info

(Optional) Displays information about the fans tray.fans

(Optional) Displays information about the power supply.power-supply


Diagnostics Commandsshow diag

Syntax Description (Optional) Displays detailed hardware and diagnostics information.

Specifying the details keyword displays EEPROM information forthe chassis or specified node.

Note

details

(Optional) Displays a summary of the installed hardware.summary

(Optional) Identifies the node for which you want to display information. Thenode-id argument is expressed in the rack/slot/module notation.

node-id

(Optional) Displays EEPROM information for the specified node or component(chassis, fan, or power supply).

eeprom-info

(Optional) Displays power register information for the specified node.power-regs

(Optional) Displays information about the chassis.chassis

chassis-info

(Optional) Displays information about the fan trays.fans

(Optional) Displays information about the power supply.power-supply

Command Default Diagnostics for all nodes installed in the router are displayed.

Hardware and software information for all nodes installed in the router is displayed

Command Modes EXEC

Administration EXEC


This command was introduced.Release 2.0

Command output was modified to display the last diagnostic resultfor a card.

Release 3.2

The chassis-info keyword was introduced.Release 3.3.0


Usage Guidelines The show diag command displays detailed information on the hardware components for each node, and onthe status of the software running on each node.




readsysmgr

Examples The following example shows excerpts of output from the show diag details command:

RP/0/RP0/CPU0:router# show diag details

CARD 0/1/* : Cisco CRS-1 Series Modular Services CardMAIN: board type 500060800-25021-05 rev B0dev 079239S/N SAD0925050JPCA: 73-7648-08 rev B0PID: CRS-MSCVID: V02CLEI: IPUCAC1BAAECI: 132502RMA: Test Hist: ab, RMA#: 00-00-00, RMA Hist: 00DIAGNOSTICS RESULTS:ENTRY 1: 0TIMESTAMP: 00/00/0000 00:00:00VERSION: v0.0PARAM1: 0 PARAM2: n/aTESTNUM: 0RESULT: 0 (PASS)ERRCODE: 0ENTRY 2: 0TIMESTAMP: 00/00/0000 00:00:00VERSION: v0.0PARAM1: 0 PARAM2: n/aTESTNUM: 0RESULT: 0 (PASS)ERRCODE: 0ENTRY 3: 0TIMESTAMP: 00/00/0000 00:00:00VERSION: v0.0PARAM1: 0 PARAM2: n/aTESTNUM: 0RESULT: 0 (PASS)ERRCODE: 0PLIM 0/PL1/* : Cisco Carrier Routing System SPA Interface Processor CardMAIN: board type 580070800-23819-03 rev C0dev N/AS/N SAD09410538PCA: 73-8982-06 rev C0PID: CRS1-SIP-800VID: V01CLEI: COUIAAMCAAECI: 134912RMA: Test Hist: ab, RMA#: 00-00-00, RMA Hist: 00DIAGNOSTICS RESULTS:ENTRY 1: 0TIMESTAMP: 00/00/0000 00:00:00VERSION: v0.0PARAM1: 0 PARAM2: n/aTESTNUM: 0RESULT: 0 (PASS)ERRCODE: 0ENTRY 2: 0TIMESTAMP: 00/00/0000 00:00:00VERSION: v0.0PARAM1: 0 PARAM2: n/a



TESTNUM: 0RESULT: 0 (PASS)ERRCODE: 0ENTRY 3: 0TIMESTAMP: 00/00/0000 00:00:00VERSION: v0.0PARAM1: 0 PARAM2: n/aTESTNUM: 0RESULT: 0 (PASS)ERRCODE: 0Interface port config: 0 PortsOptical reach type: UnknownConnector type: MT-PNODE 0/1/CPU0Node State : IOS XR RUNPLD: Motherboard: 0x0025, Processor: 0xda13, Power: N/AMONLIB: QNXFFS Monlib Version 3.1ROMMON: Version 1.51(20080807:092259) [CRS-1 ROMMON]CPU0: ASMP, CPU1: N/ASPEED: OSC Speed: 100 Mhz, CPU Speed: 800 MhzBUS Speed: 100 Mhz, MEM Speed: 100 MhzMEM Size: 1024 MbytesSPA 0/1/0 : 4-port OC3/STM1 POS Shared Port AdapterMAIN: board type 044068-2169-01 rev C0dev N/AS/N JAB093305VCPCA: 73-9313-04 rev B0PID: SPA-4XOC3-POSVID: V01CLEI: IPUIAFNRAANode State : OK...

The output displayed for the show diag details command is the most comprehensive output displayed forshow diag command variations. All other variations show a subset of the fields displayed except for the showdiag chassis, show diag fans, and show diag power-supply commands, which also enable you to displayEEPROM information.

Rack 0 - Cisco CRS-1 Series 8 Slots Line Card Chassis00: 03 00 01 E4 43 52 53 2D 38 2D 4C 43 43 00 00 00 ....CRS-8-LCC...10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................20: 49 50 4D 45 5A 31 30 42 52 41 06 CF B3 00 00 00 IPMEZ10BRA......30: 00 00 00 00 00 00 00 15 63 58 B9 00 08 00 00 00 ........cX......40: 00 49 00 21 F8 03 50 03 20 00 5A E7 04 78 00 01 .I.!..P. .Z..x..50: 54 42 41 30 39 33 36 30 30 39 30 00 00 00 00 00 TBA09360090.....60: 01 2B DB 00 00 00 00 00 00 00 00 00 00 00 00 00 .+..............70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................A0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................B0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................C0: 00 00 00 00 00 00 00 00 00 00 00 00 00 43 49 53 .............CISD0: 43 4F 20 53 59 53 54 45 4D 53 2C 20 49 4E 43 2E CO SYSTEMS, INC.E0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................F0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................

RP/0/5/CPU0:router# show diag detailsSLOT 0 (RP/LC 0): Cisco 12000 Series - Multi-Service BladeMAIN: type 150, 800-25972-02 rev A0 dev 0HW config: 0x00 SW key: 00-00-00PCA: 73-9289-04 rev A0 ver 3HW version 1.0 S/N SAD11360218MBUS: Embedded AgentTest hist: 0x00 RMA#: 00-00-00 RMA hist: 0x00DIAG: Test count: 0x00000000 Test results: 0x00000000EEPROM contents (hex):Release ModificationRelease 3.3.0 The chassis-info keyword was added to the show diags command on theCisco XR 12000 Series Router.



Task ID Operationssysmgr read00: 01 00 0C 00 00 00 00 00 00 00 00 00 00 00 00 0010: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 0020: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 0030: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 0040: 00 96 01 00 00 49 00 24 49 04 50 03 FE 01 00 0350: 03 20 00 65 74 02 50 00 00 00 00 0A 01 00 00 0060: 53 41 44 31 31 33 36 30 32 31 38 00 00 00 00 0070: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 0080: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 0090: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00A0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00B0: 00 00 00 00 00 00 00 00 00 00 00 00 00 DA 00 00C0: 58 52 2D 31 32 4B 2D 4D 53 42 00 00 00 00 00 00D0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00E0: 02 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00F0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00FRU: Linecard/Module: 12000-ServEngCardL3 Engine: Service Engine - ISE OC192 (10 Gbps)MBUS Agent Software version 4.4 (RAM) (ROM version is 4.4)Using CAN Bus AROM Monitor version 1.3Fabric Downloader version used 3.2 (ROM version is 3.2)Primary clock is CSC0Board State is IOS-XR RUNLast Reset Reason: Card graceful rebootInsertion time: Fri Oct 10 22:34:58 2008 (4w2d ago)DRAM size: 2147483648 bytesFrFab SDRAM size: 1610612736 bytesToFab SDRAM size: 268435456 bytes0 resets since restart/fault forgive...SLOT 2 (RP/LC 2): Cisco 12000 Series SPA Interface Processor- 601MAIN: type 149, 68-2647-01 rev A0 dev 85437HW config: 0x20 SW key: 00-00-00PCA: 73-9607-04 rev A0 ver 4HW version 1.0 S/N SAD10330441MBUS: Embedded AgentTest hist: 0x00 RMA#: 00-00-00 RMA hist: 0x00DIAG: Test count: 0x00000000 Test results: 0x00000000EEPROM contents (hex):00: 01 00 0C 00 00 00 00 00 00 00 00 00 00 00 00 0010: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 0020: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 0030: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 0040: 00 95 01 00 00 49 00 25 87 04 50 04 FE 01 00 0050: 00 44 00 0A 57 01 50 01 4D BD 20 09 01 00 00 0060: 53 41 44 31 30 33 33 30 34 34 31 00 00 00 00 0070: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 0080: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 0090: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00A0: 00 01 40 98 00 00 00 00 00 00 00 00 00 00 00 00B0: 00 00 00 00 00 00 00 00 00 00 00 00 00 DA 00 00C0: 31 32 30 30 30 2D 53 49 50 2D 36 30 31 00 00 00D0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00E0: 01 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00F0: B8 07 A4 1F 8A 52 6D 1F 9A CE AE CF BF F4 00 00FRU: Linecard/Module: 12000-SIP-601Route Memory: MEM-LC5-2048=Packet Memory: MEM-LC5-PKT-512=L3 Engine: 5 (MultiRate) - ISE OC192 (10 Gbps)Operational rate mode: 10 GbpsMBUS Agent Software version 4.4 (RAM) (ROM version is 4.2)Using CAN Bus AROM Monitor version 17.1Fabric Downloader version used 4.7 (ROM version is 4.7)Primary clock is CSC0Board State is IOS-XR RUNLast Reset Reason: Reload initiated by userInsertion time: Wed Nov 5 17:39:51 2008 (5d01h ago)DRAM size: 2147483648 bytesFrFab SDRAM size: 268435456 bytes



ToFab SDRAM size: 268435456 bytes0 resets since restart/fault forgiveSPA Information:subslot 0/2/0: SPA-4XOC3-POS-V2 (0x526), status is oksubslot 0/2/1: SPA-IPSEC-2G-2 (0x549), status is oksubslot 0/2/2: SPA-8X1FE (0x4c5), status is oksubslot 0/2/3: Empty...SLOT 5 (RP/LC 5): Cisco 12000 Series Performance Route Processor 2MAIN: type 96, 800-23469-06 rev A0 dev 84610HW config: 0x10 SW key: 00-00-00PCA: 73-8812-09 rev A0 ver 7HW version 0.0 S/N SAD103003M7MBUS: MBUS Agent (1) 73-8048-07 rev A0 dev 0HW version 0.1 S/N SAL1026THV9Test hist: 0x00 RMA#: 00-00-00 RMA hist: 0x00DIAG: Test count: 0x00000000 Test results: 0x00000000EEPROM contents (hex):00: 01 00 01 00 49 00 1F 70 07 50 00 00 00 00 00 0010: 53 41 4C 31 30 32 36 54 48 56 39 00 00 00 00 0020: 00 01 00 00 00 00 00 00 00 00 00 00 00 00 00 0030: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 0040: 00 60 00 00 00 49 00 22 6C 09 50 07 00 02 00 0050: 03 20 00 5B AD 06 50 01 4A 82 10 00 01 00 00 0060: 53 41 44 31 30 33 30 30 33 4D 37 00 00 00 00 0070: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 0080: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 0090: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00A0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00B0: 00 00 00 00 00 00 00 00 00 00 00 00 32 DA 00 00C0: 50 52 50 2D 32 00 00 00 00 00 00 00 00 00 00 00D0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00E0: 04 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00F0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00FRU: Linecard/Module: PRP-2Route Memory: MEM-PRP/LC-2048=MBUS Agent Software version 4.4 (RAM) (ROM version is 4.2)Using CAN Bus AROM Monitor version 1.16dev(0.1)Primary clock is CSC0Board State is IOS-XR RUNInsertion time: Fri Oct 10 21:19:10 2008 (4w2d ago)DRAM size: 2147483648 bytes0 resets since restart/fault forgive

The output displayed for the show diag details command is the most comprehensive output displayed forshow diag command variations. All other variations show a subset of the fields displayed except for the showdiag details chassis-info and show diag summary chassis-info commands, which show different information.

RP/0/RSP0/CPU0:router# show diag details

NODE module 0/RSP0/CPU0 : ASR9K Fabric, Controller, 4G memoryMAIN board type 0x100302 S/N: FOC1229801RTop Assy. Number68-3160-04PID A9K-RSP-4GUDI_VIDHwRev: V4.8New Deviation NumberCLEITBDTBDBoard State IOS XR RUNBoard State IOS XR RUN PLD: Motherboard: N/A, Processor:0x8004 (rev: 2.2), Power: N/AMONLIBQNXFFS Monlib Version 32ROMMONVersion 1(20081208:173612) [ASR9K ROMMON] BoardFPGA/CPLD/ASIC Hardware Revision:CompactFlash V1.0XbarSwitch0 V1.3 XbarSwitch1 V1.3 XbarArbiter V1.0XbarInterfaceV18.4IntCtrl V114ClkCtrl V1.13PuntFPGA V1.4HD V3.USB0 V17.USB1 V17CPUCtrl V1.17UTIV1.6LIU V1.MLANSwitch V0.EOBCSwitch V2CBC (active partition) v1.1CBC (inactivepartition) v1.More--

This table describes the significant fields shown in the display.



Table 1: show diag Field Descriptions

DescriptionField

Provides the following general information about thehardware:

• Board type

• Revision

• Device identifier

• Serial number

MAIN

Cisco printed circuit assembly (PCA) hardware andrevision number.

PCA

Displays the product identifier (PID) revision for thespecified node.

PID

Displays the version identifier (VID) for the specifiednode.

VID

Displays the common language equipment identifier(CLEI) for the specified node.

CLEI

Displays the equipment catalog item (ECI) for thespecified node.

ECI

Displays the current software on the board andwhether or not the board is running.

Board State

Displays the information about the followingprogrammable logic device (PLD) components onthe current module:

• Processor

• Power

• MONLIB

PLD

Displays speed information for the variouscomponents of the specified node, in megahertz.

SPEED

Displays the memory size of the specified node, inmegabytes.

MEM Size

Displays returned material adjustment (RMA)information for the specified node.

RMA



DescriptionField

Provides the following information about the lastdiagnostics test that was run on the specified node:

• ENTRY 1

• TIMESTAMP—Time stamp for the lastdiagnostic test that was run on the node.

• VERSION

• PARAM1

• PARAM2

• TESTNUM—Identifies the test that was run onthe node.

• RESULT—Displays whether the last diagnostictest passed or failed.

• ERRCODE

DIAGNOSTICS RESULTS

Table 2: show diags Field Descriptions

DescriptionField

Physical slot number of the line card.SLOT

General information about the hardware.MAIN

Cisco Protection Channel Access (PCA) hardwareand revision number.

PCA

Provides version information for the Mbus agent.MBUS

Results of the last diagnostics test, in hexadecimalformat.

DIAG

EEPROM contents, in hexadecimal, of thecomponent.

EEPROM contents

Information about the Field-replaceable Units (FRUs)associated with the nodes that are installed in therouter.

FRU

Mbus agent software version currently running onthe router.

MBUS Agent Software version

Version of monitor library used by ROMMON.ROMMonitor version



DescriptionField

Version of fabric downloader used.Fabric Downloader version

Primary clock source configured on the router.Primary clock

Current software on the board, and whether or not theboard is running.

Board State

Reason the card was last reset.Last Reset Reason

Time at which the last diagnostics test was executed.Insertion time

Dynamic Random-Access Memory (DRAM) size inbytes.

DRAM size

Number of resets since the card was last restarted.number resets since restart/fault forgive

Subslot in which SPA is installed, name of SPA, andcurrent status of SPA.

SPA Information

The following example shows how to display EEPROM information:

RP/0/RP0/CPU0:router(admin)# show diag chassis eeprom-info

Rack 0 - Cisco CRS-1 Series 8 Slots Line Card Chassis00: 03 00 01 E4 43 52 53 2D 38 2D 4C 43 43 00 00 00 ....CRS-8-LCC...10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................20: 49 50 4D 45 5A 31 30 42 52 41 06 CF B3 00 00 00 IPMEZ10BRA......30: 00 00 00 00 00 00 00 15 63 58 B9 00 08 00 00 00 ........cX......40: 00 49 00 21 F8 03 50 03 20 00 5A E7 04 78 00 01 .I.!..P. .Z..x..50: 54 42 41 30 39 33 36 30 30 39 30 00 00 00 00 00 TBA09360090.....60: 01 2B DB 00 00 00 00 00 00 00 00 00 00 00 00 00 .+..............70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................A0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................B0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................C0: 00 00 00 00 00 00 00 00 00 00 00 00 00 43 49 53 .............CISD0: 43 4F 20 53 59 53 54 45 4D 53 2C 20 49 4E 43 2E CO SYSTEMS, INC.E0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................F0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................

RP/0/RSP15/CPU0:router# show diag chassis eeprom-info

Rack 0 - ASR-9010 Chassis, Includes AccessoriesController Family HW config: 0x20 SW key: ef Controller Type: 2fePID ASR9010AC Version Identifier : 0UDI Namechassis ASR-9010-ACUDI Description ASR9010, AC Chassis Part Number (68-bbbb-vv): 68-1234-56Part Revision : 0.1PCB Serial Number : FOX1232H67MPCA Number (73-bbbb-vv) : 73-1159-02 PCARevision : 0.Deviation Number # 1 0 CLEI Code : NOCLEIManufacturing Test Data : 00 00 00 00 00 00 00 00Base MAC Address : 001d.e5eb.bfa8MAC Address block size : 264Hardware Revision : 0.100Capabilities : 00Field Diagnostics Data 00 00 00 00 00 00 00 00 Device values :Power Usage (10mW units) : 0



ENVMON Information 0 0 0 0 0 0 0 0 0 0 0 0 0 0 000 0 0 0 0 0 0 00 0 0 0 0 0 0 0

The following example shows how to display detailed information for a chassis:

RP/0/5/CPU0:router# show diag details chassis-info

Backplane NVRAM [version 0x20] Contents -Chassis: type 12406 Fab Ver: 2Chassis S/N: TBM10421465

PCA: 73-5796-2 rev: C0 dev: 0 HW ver: 1.0Backplane S/N: TBM10402356

MAC Addr: base 0019.aaa3.3a00 block size: 1024RMA Number: 0x00-0x00-0x00 code: 0x00 hist: 0x00Backplane NVRAM (hex)00: 20 00 00 49 16 a4 00 02 00 60 00 02 01 00 00 0710: 54 42 4d 31 30 34 30 32 33 35 36 00 00 00 00 0020: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 0030: 54 42 4d 31 30 34 32 31 34 36 35 00 00 00 00 0040: 00 19 aa a3 3a 00 04 00 00 00 00 00 00 00 00 0050: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 0060: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 0070: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00

Table 3: show diags details chassis-info Field Descriptions

DescriptionField

Type and fabrication version of the chassis.Chassis

Serial number of the chassis.Chassis S/N

Cisco Protection Channel Access (PCA) hardwareand revision number.

PCA

Serial number of the backplane.Backplane S/N

MAC address and block size of the chassis.MAC Addr

RMA information for the chassis.RMA Number

Contents of the backplane NVRAM, in hexadecimal.Backplane NVRAM


Displays information and status for each node in thesystem.

show platform

Displays details on the hardware and software statusof the system.

show version



show diagnostic bootup levelTo display the current diagnostic bootup level, use the show diagnostic bootup level command in AdminEXEC modeSystem Admin EXEC mode.

show diagnostic bootup level location node-id

Syntax Description Specifies a card. The node-id argument is entered in the rack/slot/modulenotation.

location node-id

Command Default No default behavior or values.





Usage Guidelines Use the show diagnostic bootup level command to display the current diagnostic bootup level for a specifiedcard.


Note


Note


readdiag


Diagnostics Commandsshow diagnostic bootup level

Examples The following example shows how to display the current diagnostic bootup level for 0/1/cpu0:

RP/0/0RP0RSP0/CPU0:router:hostname(admin)# show diagnostic bootup level location 0/1/cpu0

Current bootup diagnostic level for LC 0/1/CPU0: minimal


Diagnostics Commandsshow diagnostic bootup level

show diagnostic contentTo display test information including test ID, test attributes, and supported coverage test levels for each testand for all components, use the show diagnostic content command in Admin EXEC modeSystem AdminEXEC mode.

show diagnostic content location node-id

Syntax Description Displays the diagnostic content for a specified location. The node-id argumentis entered in the rack/slot/module notation.

location node-id






Usage Guidelines Use the show diagnostic content command to display diagnostic test information for a specific location. Thetest information includes the supported tests and attributes.


Note


Note



Diagnostics Commandsshow diagnostic content


readdiag

Examples The following example shows how to display the test information for a specified location:

For a route switch processor:

RP/0/RSP0/CPU0:router(admin)# show diagnostic content location 0/rsp0/cpuo

Wed Feb 16 09:17:07.293 PST

RP 0/RSP0/CPU0:

Diagnostics test suite attributes:M/C/* - Minimal bootup level test / Complete bootup level test / NA

B/* - Basic ondemand test / NAP/V/* - Per port test / Per device test / NA

D/N/* - Disruptive test / Non-disruptive test / NAS/* - Only applicable to standby unit / NAX/* - Not a health monitoring test / NAF/* - Fixed monitoring interval test / NAE/* - Always enabled monitoring test / NAA/I - Monitoring is active / Monitoring is inactive

Test Interval Thre-ID Test Name Attributes (day hh:mm:ss.ms shold)

==== ================================== ============ ================= =====1) PuntFPGAScratchRegister ---------> ***N****A 000 00:01:00.000 12) FIAScratchRegister --------------> ***N****A 000 00:01:00.000 13) ClkCtrlScratchRegister ----------> ***N****A 000 00:01:00.000 14) IntCtrlScratchRegister ----------> ***N****A 000 00:01:00.000 15) CPUCtrlScratchRegister ----------> ***N****A 000 00:01:00.000 16) FabSwitchIdRegister -------------> ***N****A 000 00:01:00.000 17) EccSbeTest ----------------------> ***N****I 000 00:01:00.000 38) SrspStandbyEobcHeartbeat --------> ***NS***A 000 00:00:05.000 39) SrspActiveEobcHeartbeat ---------> ***NS***A 000 00:00:05.000 310) FabricLoopback ------------------> M**N****A 000 00:01:00.000 311) PuntFabricDataPath --------------> ***N****A 000 00:01:00.000 312) FPDimageVerify ------------------> ***N****I 001 00:00:00.000 1

RP/0/0RP0RSP0/CPU0:router:hostname(admin): show diagnostic contentlocation 0/rp0/cpu0

Diagnostics test suite attributes:M/C/* - Minimal bootup level test / Complete bootup level test / NA

B/* - Basic ondemand test / NAP/V/* - Per port test / Per device test / NA

D/N/* - Disruptive test / Non-disruptive test / NA

S/* - Only applicable to standby unit / NAX/* - Not a health monitoring test / NAF/* - Fixed monitoring interval test / NAE/* - Always enabled monitoring test / NAA/I - Monitoring is active / Monitoring is inactive




==== ================================== ============ ================= =====1) ControlEthernetPingTest ---------> *B*N*X**I 001 00:00:00.000 12) SelfPingOverFabric --------------> *B*N*X**I 001 00:00:00.000 13) FabricPingTest ------------------> *B*N*X**I 001 00:00:00.000 14) ControlEthernetInactiveLinkTest -> *B*NS***I 001 00:00:00.000 15) RommonRevision ------------------> *B*N*X**I 001 00:00:00.000 16) FabricDiagnosisTest -------------> *B*NS***I 000 00:02:00.000 17) FilesystemBasicDisk0 ------------> *B*N****I 003 00:00:00.000 18) FilesystemBasicDisk1 ------------> *B*N****I 003 00:00:00.000 19) FilesystemBasicHarddisk ---------> *B*N****I 003 00:00:00.000 110) ScratchRegisterTest -------------> CBVN****I 001 00:00:00.000 111) FabricMcastTest -----------------> *B*NS***I 000 00:02:00.000 112) ControlEthernetIntraSwitchTest --> *B*N****I 000 00:00:02.000 313) FabricUcastMcastTest ------------> *B*N****A 000 00:01:00.000 1

For a line card:

RP/0/0RP0RSP0/CPU0:router:hostname(admin)# show diagnostic content location 0/1/cpu0

Wed Feb 16 09:27:01.424 PST

MSC 0/1/CPU0:

Diagnostics test suite attributes:M/C/* - Minimal bootup level test / Complete bootup level test / NAB/* - Basic ondemand test / NA

P/V/* - Per port test / Per device test / NAD/N/* - Disruptive test / Non-disruptive test / NAS/* - Only applicable to standby unit / NAX/* - Not a health monitoring test / NAF/* - Fixed monitoring interval test / NAE/* - Always enabled monitoring test / NAA/I - Monitoring is active / Monitoring is inactive


==== ================================== ============ ================= =====1) ControlEthernetPingTest ---------> *B*N*X**I 001 00:00:00.000 12) SelfPingOverFabric --------------> *B*N*X**I 001 00:00:00.000 13) RommonRevision ------------------> *B*N*X**I 001 00:00:00.000 14) ScratchRegisterTest -------------> CBVN****I 001 00:00:00.000 15) TcamFullScanTest ----------------> *BVN****I 001 00:00:00.000 16) EgressqMemoryBISTTest -----------> **VD*X**I 001 00:00:00.000 17) IngressqMemoryBISTTest ----------> **VD*X**I 001 00:00:00.000 18) FabricqMemoryBISTTest -----------> **VD*X**I 001 00:00:00.000 1

RP/0/RSP0/CPU0:router(admin)# show diagnostic content location 0/1/cpu0

A9K-40GE-L 0/1/CPU0:

Diagnostics test suite attributes:M/C/* - Minimal bootup level test / Complete bootup level test / NAabP/V/* - Per port test / Per device test / NAD/N/* - Disruptive test / Non-disruptive test / NAS/* - Only applicable to standby unit / NAX/* - Not a health monitoring test / NAF/* - Fixed monitoring interval test / NAE/* - Always enabled monitoring test / NAA/I - Monitoring is active / Monitoring is inactive

Test Interval Thre-ID Test Name Attributes (day hh:mm:ss.ms shold)==== ================================== ============ ================= =====1) PHYCtrlScratchRegister ----------> ***N****A 000 00:01:00.000 12) PortCtrlScratchRegister ---------> ***N****A 000 00:01:00.000 13) CPUCtrlScratchRegister ----------> ***N****A 000 00:01:00.000 14) NPScratchRegister ---------------> ***N****A 000 00:01:00.000 15) BridgeScratchRegister -----------> ***N****A 000 00:01:00.000 16) FIAScratchRegister --------------> ***N****A 000 00:01:00.000 1



7) EccSbeTest ----------------------> ***N****I 000 00:01:00.000 38) LcEobcHeartbeat -----------------> ***N****A 000 00:00:05.000 39) NPULoopback ---------------------> ***N****A 000 00:01:00.000 310) FPDimageVerify ------------------> ***N****I 001 00:00:00.000 1

Here is an example of show diagnostic content location command for FabricUcastMcast Test.RP/0/RP0/CPU0:router(admin)#show diagnostic content location 0/0/CPU0Thu Mar 3 13:45:26.115 PSTDRP 0/0/CPU0:Diagnostics test suite attributes:M/C/* - Minimal bootup level test / Complete bootup level test / NAB/* - Basic ondemand test / NA

P/V/* - Per port test / Per device test / NAD/N/* - Disruptive test / Non-disruptive test / NAS/* - Only applicable to standby unit / NAX/* - Not a health monitoring test / NAF/* - Fixed monitoring interval test / NAE/* - Always enabled monitoring test / NAA/I - Monitoring is active / Monitoring is inactive

Test Interval Thre-ID Test Name Attributes (day hh:mm:ss.ms shold)==== ================================== ============ ================= =====1) ControlEthernetPingTest ---------> *B*N*X**I 001 00:00:00.000 12) SelfPingOverFabric --------------> *B*N*X**I 001 00:00:00.000 13) FabricPingTest ------------------> *B*N*X**I 001 00:00:00.000 14) ControlEthernetInactiveLinkTest -> *B*NS***I 001 00:00:00.000 15) RommonRevision ------------------> *B*N*X**I 001 00:00:00.000 16) FabricDiagnosisTest ------------> *B*NS***I 000 00:02:00.000 17) FilesystemBasicDisk0 ------------> *B*N****I 003 00:00:00.000 18) FilesystemBasicDisk1 ------------> *B*N****I 003 00:00:00.000 19) FilesystemBasicHarddisk ---------> *B*N****I 003 00:00:00.000 110) ScratchRegisterTest -------------> CBVN****I 001 00:00:00.000 111) FabricMcastTest -----------------> *B*NS***A 000 00:02:00.000 112) ControlEthernetIntraSwitchTest --> ***N****I 000 00:00:02.000 313) FabricUcastMcastTest ------------> *B*N****A 000 00:01:00.000 1

Table 4: show diagnostic content Field Descriptions, on page 46 describes the significant fields shown inthe display.

Table 4: show diagnostic content Field Descriptions

DescriptionField

Minimal bootup test or complete bootup test.M/C/* -Minimal bootup level test / Complete bootuplevel test / NA

Basic on-demand test.B/* - Basic ondemand test / NA

Test is per port or device.P/V/* - Per port test / Per device test / NA

Test is disruptive or nondisruptive.D/N/* - Disruptive test / Non-disruptive test / NA

Test is available for standby node only.S/* - Only applicable to standby unit / NA

Test is not a health-monitoring test.X/* - Not a health monitoring test / NA

Test is a fixed monitoring interval test.F/* - Fixed monitoring interval test / NA

Test is an always enabled monitoring test.E/* - Always enabled monitoring test / NA

Test is active or inactive.A/I - Monitoring is active / Monitoring is inactive



DescriptionField

ID of the test.ID

Name of the test.Test Name

Attributes for the test.Attributes

Interval of the test.Test Interval

Failure threshold of the text.Threshold


Loads an offline diagnostic image for integrated fielddiagnostics.

diagnostic load, on page 2

Configures the health-monitoring diagnostic testing for aspecified interval for a specified location.

diagnostic monitor interval, on page 6

Configures a diagnostic schedule.diagnostic schedule, on page 14


Unloads an offline diagnostic image.diagnostic unload, on page 24



show diagnostic ondemand settingsTo display the current on-demand settings, use the show diagnostic ondemand settings command in AdminEXEC modeSystem Admin EXEC mode .

show diagnostic ondemand settings









readdiag

Examples The following example shows how to display the on-demand settings:

RP/0/0RP0RSP0/CPU0:router:hostname(admin)# show diagnostic ondemand settings

Test iterations = 45Action on test failure = continue until test failure limit reaches 25


Diagnostics Commandsshow diagnostic ondemand settings

show diagnostic resultTo display diagnostic test results, use the show diagnostic result command in Admin EXEC modeSystemAdmin EXEC mode.

show diagnostic result location node-id[test {id| test-name| all}] [detail]

Syntax Description Displays the diagnostic test results for a specified location. The node-id argumentis entered in the rack/slot/module notation.

location node-id

(Optional) Specifies diagnostic test selection. The following test selections areavailable:

• id—Test ID or list of test IDs , as shown in the show diagnostic contentcommand .Multiple tests can be listed if separated by semicolons (;) as follows:

◦x;y-z (for example: 1; 3-4 or 1;3;4)

• test-name—Test name.

• all—Specifies all tests.

Use the show diagnostic content command in administration EXEC mode to seea list of test names and their associated IDs.

test {id | test-name |all}

(Optional) Specifies detailed results.detail






Usage Guidelines Use the show diagnostic result command to display diagnostic results for a specific location.


Diagnostics Commandsshow diagnostic result


Note


Note



readdiag

Examples The following example shows how to display detailed diagnostic test results:

RP/0/RSP0/CPU0:router(admin)# show diagnostic result loc 0/RSP0/CPU0 test 1Current bootup diagnostic level for RP 0/RSP0/CPU0: minimalTest results: (. = Pass, F = Fail, U = Untested)1 ) PuntFPGAScratchRegister ---------> .RP/0/RSP0/CPU0:router(admin)#RP/0/RSP0/CPU0:router(admin)# show diagnostic result loc 0/RSP0/CPU0 test allCurrent bootup diagnostic level for RP 0/RSP0/CPU0: minimalTest results: (. = Pass, F = Fail, U = Untested)1 ) PuntFPGAScratchRegister ---------> .2 ) XbarInterfaceScratchRegister ----> .3 ) ClkCtrlScratchRegister ----------> .4 ) IntCtrlScratchRegister ----------> .5 ) CPUCtrlScratchRegister ----------> .6 ) XbarSwitchIdRegister ------------> .7 ) EccSbeTest ----------------------> U8 ) SrspStandbyEobcHeartbeat --------> U9 ) SrspActiveEobcHeartbeat ---------> U10 ) FabricLoopback ------------------> .11 ) PuntFabricDataPath --------------> .12 ) FPDimageVerify ------------------> .

RP/0/0RP0RSP0/CPU0:router:hostname(admin)# show diagnostic result location 0/3/CPU0 test 1detail

Test results: (. = Pass, F = Fail, U = Untested)___________________________________________________________________________1 ) Control Ethernet Ping Test ------> .Error code ------------------> 0 (DIAG_SUCCESS)Total run count -------------> 1Last test execution time ----> Thu Aug 11 18:13:38.918 2005First test failure time -----> n/aLast test failure time ------> n/aLast test pass time ---------> Thu Aug 11 18:13:38.918 2005Total failure count ---------> 0Consecutive failure count ---> 0



Here is an example of the show diagnostic results detail command run on the route switch processor labeledRSP0:

RP/0/RSP0/CPU0:router(admin)# show diagnostic result loc 0/RSP0/CPU0 detail

Current bootup diagnostic level for RP 0/RSP0/CPU0: minimal

RP 0/RSP0/CPU0:

Overall diagnostic result: PASSDiagnostic level at card bootup: minimal

Test results: (. = Pass, F = Fail, U = Untested)

___________________________________________________________________________

1 ) PuntFPGAScratchRegister ---------> .

Error code ------------------> 0 (DIAG_SUCCESS)Total run count -------------> 265Last test execution time ----> Tue Mar 10 16:31:43 2009First test failure time -----> n/aLast test failure time ------> n/aLast test pass time ---------> Tue Mar 10 16:31:43 2009Total failure count ---------> 0Consecutive failure count ---> 0

___________________________________________________________________________

2 ) XbarInterfaceScratchRegister ----> .


___________________________________________________________________________

3 ) ClkCtrlScratchRegister ----------> .


___________________________________________________________________________

4 ) IntCtrlScratchRegister ----------> .


___________________________________________________________________________

5 ) CPUCtrlScratchRegister ----------> .

Error code ------------------> 0 (DIAG_SUCCESS)Total run count -------------> 264Last test execution time ----> Tue Mar 10 16:31:43 2009First test failure time -----> n/aLast test failure time ------> n/a



Last test pass time ---------> Tue Mar 10 16:31:43 2009Total failure count ---------> 0Consecutive failure count ---> 0

___________________________________________________________________________

6 ) XbarSwitchIdRegister ------------> .


Here is an example of show diagnostic result command to view the results of the FabricUcastMcast Test.RP/1/RP0/CPU0:router(admin)#show diagnostic result location 0/rp1/cpu0 testFabricUcastMcastTest detailFri Mar 4 11:21:01.153 UTCCurrent bootup diagnostic level for RP 0/RP1/CPU0: bypassTest results: (. = Pass, F = Fail, U = Untested)___________________________________________________________________________13 ) FabricUcastMcastTest ------------> .

Error code ------------------> 0 (DIAG_SUCCESS)Total run count -------------> 17Last test execution time ----> Fri Mar 4 11:20:54 2011First test failure time -----> Fri Mar 4 11:19:47 2011Last test failure time ------> Fri Mar 4 11:19:47 2011Last test pass time ---------> Fri Mar 4 11:20:54 2011Total failure count ---------> 1Consecutive failure count ---> 0

Unicast Resultsdest: (all nodes) session_id: 48ret_code: 0 (No error)rx_ret_code: 0 (No error)tx_ret_code: 0 (No error)min_rtt_ms: 2 max_rtt_ms: 63ping_mode_mask: 0x00000099 fplane_bitmap: 0x000000ffinter_packet_delay: 0 max_timeout_ms: 1500late_timeout_ms: 1500 priority: 0flags: 0x00000000 pkt_cnt: 10pkt_size: 1000 num_nodes: 15tx_start_ts: 11:20:54.488 UTC Fri Mar 04 2011modes: 0 - LP/fabricq0, 3 - LP/fabricq1, 4 - HP/fabricq0, 7 - HP/fabricq1

node[mode] req'ed rx_good tx_good tx_unrea tx_err rx_unexp rx_corr============== ======== ======== ======== ======== ======== ======== ========

0/0/CPU0[0] 10 10 10 0 0 0 00/0/CPU0[3] 10 10 10 0 0 0 00/0/CPU0[4] 10 10 10 0 0 0 00/0/CPU0[7] 10 10 10 0 0 0 00/4/CPU0[0] 10 10 10 0 0 0 00/4/CPU0[3] 10 10 10 0 0 0 00/4/CPU0[4] 10 10 10 0 0 0 00/4/CPU0[7] 10 10 10 0 0 0 00/5/CPU0[0] 10 10 10 0 0 0 00/5/CPU0[3] 10 10 10 0 0 0 00/5/CPU0[4] 10 10 10 0 0 0 00/5/CPU0[7] 10 10 10 0 0 0 00/6/CPU0[0] 10 10 10 0 0 0 00/6/CPU0[3] 10 10 10 0 0 0 00/6/CPU0[4] 10 10 10 0 0 0 00/6/CPU0[7] 10 10 10 0 0 0 00/8/CPU0[0] 10 10 10 0 0 0 00/8/CPU0[4] 10 10 10 0 0 0 0

0/RP0/CPU0[0] 10 10 10 0 0 0 00/RP0/CPU0[4] 10 10 10 0 0 0 00/RP1/CPU0[0] 10 10 10 0 0 0 00/RP1/CPU0[4] 10 10 10 0 0 0 01/3/CPU0[0] 10 10 10 0 0 0 01/3/CPU0[3] 10 10 10 0 0 0 01/3/CPU0[4] 10 10 10 0 0 0 01/3/CPU0[7] 10 10 10 0 0 0 0



1/4/CPU0[0] 10 10 10 0 0 0 01/4/CPU0[3] 10 10 10 0 0 0 01/4/CPU0[4] 10 10 10 0 0 0 01/4/CPU0[7] 10 10 10 0 0 0 01/7/CPU0[0] 10 10 10 0 0 0 01/7/CPU0[4] 10 10 10 0 0 0 01/9/CPU0[0] 10 10 10 0 0 0 01/9/CPU0[3] 10 10 10 0 0 0 01/9/CPU0[4] 10 10 10 0 0 0 01/9/CPU0[7] 10 10 10 0 0 0 01/14/CPU0[0] 10 10 10 0 0 0 01/14/CPU0[3] 10 10 10 0 0 0 01/14/CPU0[4] 10 10 10 0 0 0 01/14/CPU0[7] 10 10 10 0 0 0 01/15/CPU0[0] 10 10 10 0 0 0 01/15/CPU0[4] 10 10 10 0 0 0 01/RP0/CPU0[0] 10 10 10 0 0 0 01/RP0/CPU0[4] 10 10 10 0 0 0 01/RP1/CPU0[0] 10 10 10 0 0 0 01/RP1/CPU0[4] 10 10 10 0 0 0 0============== ======== ======== ======== ======== ======== ======== ========Global 460 460 460 0 0 0 0

Unicast Results (Last Failure)dest: (all nodes) session_id: 30ret_code: 606182912 ('FAB_SVR' detected the 'informational' condition

'Timed outwaiting for all ping replies.')

rx_ret_code: 0 (No error)tx_ret_code: 0 (No error)min_rtt_ms: 2 max_rtt_ms: 61ping_mode_mask: 0x00000099 fplane_bitmap: 0x000000ffinter_packet_delay: 0 max_timeout_ms: 1500late_timeout_ms: 1500 priority: 0flags: 0x00000000 pkt_cnt: 10pkt_size: 1000 num_nodes: 15tx_start_ts: 11:19:47.167 UTC Fri Mar 04 2011modes: 0 - LP/fabricq0, 3 - LP/fabricq1, 4 - HP/fabricq0, 7 - HP/fabricq1


0/0/CPU0[0] 10 0 10 0 0 0 00/0/CPU0[3] 10 0 10 0 0 0 00/0/CPU0[4] 10 0 10 0 0 0 00/0/CPU0[7] 10 0 10 0 0 0 00/4/CPU0[0] 10 10 10 0 0 0 00/4/CPU0[3] 10 10 10 0 0 0 00/4/CPU0[4] 10 10 10 0 0 0 00/4/CPU0[7] 10 10 10 0 0 0 00/5/CPU0[0] 10 10 10 0 0 0 00/5/CPU0[3] 10 10 10 0 0 0 00/5/CPU0[4] 10 10 10 0 0 0 00/5/CPU0[7] 10 10 10 0 0 0 00/6/CPU0[0] 10 10 10 0 0 0 00/6/CPU0[3] 10 10 10 0 0 0 00/6/CPU0[4] 10 10 10 0 0 0 00/6/CPU0[7] 10 10 10 0 0 0 00/8/CPU0[0] 10 10 10 0 0 0 00/8/CPU0[4] 10 10 10 0 0 0 0

0/RP0/CPU0[0] 10 10 10 0 0 0 00/RP0/CPU0[4] 10 10 10 0 0 0 00/RP1/CPU0[0] 10 10 10 0 0 0 00/RP1/CPU0[4] 10 10 10 0 0 0 01/3/CPU0[0] 10 10 10 0 0 0 01/3/CPU0[3] 10 10 10 0 0 0 01/3/CPU0[4] 10 10 10 0 0 0 01/3/CPU0[7] 10 10 10 0 0 0 01/4/CPU0[0] 10 10 10 0 0 0 01/4/CPU0[3] 10 10 10 0 0 0 01/4/CPU0[4] 10 10 10 0 0 0 01/4/CPU0[7] 10 10 10 0 0 0 01/7/CPU0[0] 10 10 10 0 0 0 01/7/CPU0[4] 10 10 10 0 0 0 01/9/CPU0[0] 10 10 10 0 0 0 0



1/9/CPU0[3] 10 10 10 0 0 0 01/9/CPU0[4] 10 10 10 0 0 0 01/9/CPU0[7] 10 10 10 0 0 0 01/14/CPU0[0] 10 10 10 0 0 0 01/14/CPU0[3] 10 10 10 0 0 0 01/14/CPU0[4] 10 10 10 0 0 0 01/14/CPU0[7] 10 10 10 0 0 0 01/15/CPU0[0] 10 10 10 0 0 0 01/15/CPU0[4] 10 10 10 0 0 0 01/RP0/CPU0[0] 10 10 10 0 0 0 01/RP0/CPU0[4] 10 10 10 0 0 0 01/RP1/CPU0[0] 10 10 10 0 0 0 01/RP1/CPU0[4] 10 10 10 0 0 0 0============== ======== ======== ======== ======== ======== ======== ========Global 460 420 460 0 0 0 0

Multicast Resultsdest: FGID 1023 session_id: 49ret_code: 0 (No error)rx_ret_code: 0 (No error)tx_ret_code: 0 (No error)min_rtt_ms: 13 max_rtt_ms: 58ping_mode_mask: 0x00000011 fplane_bitmap: 0x000000ffinter_packet_delay: 0 max_timeout_ms: 1500late_timeout_ms: 1500 priority: 0flags: 0x00000000 pkt_cnt: 10pkt_size: 1000 num_nodes: 15tx_start_ts: 11:20:54.492 UTC Fri Mar 04 2011modes: 0 - LP/fabricq0, 4 - HP/fabricq0


0/0/CPU0[0] 10 10 10 0 0 0 00/0/CPU0[4] 10 10 10 0 0 0 00/4/CPU0[0] 10 10 10 0 0 0 00/4/CPU0[4] 10 10 10 0 0 0 00/5/CPU0[0] 10 10 10 0 0 0 00/5/CPU0[4] 10 10 10 0 0 0 00/6/CPU0[0] 10 10 10 0 0 0 00/6/CPU0[4] 10 10 10 0 0 0 00/8/CPU0[0] 10 10 10 0 0 0 00/8/CPU0[4] 10 10 10 0 0 0 0

0/RP0/CPU0[0] 10 10 10 0 0 0 00/RP0/CPU0[4] 10 10 10 0 0 0 00/RP1/CPU0[0] 10 10 10 0 0 0 00/RP1/CPU0[4] 10 10 10 0 0 0 01/3/CPU0[0] 10 10 10 0 0 0 01/3/CPU0[4] 10 10 10 0 0 0 01/4/CPU0[0] 10 10 10 0 0 0 01/4/CPU0[4] 10 10 10 0 0 0 01/7/CPU0[0] 10 10 10 0 0 0 01/7/CPU0[4] 10 10 10 0 0 0 01/9/CPU0[0] 10 10 10 0 0 0 01/9/CPU0[4] 10 10 10 0 0 0 01/14/CPU0[0] 10 10 10 0 0 0 01/14/CPU0[4] 10 10 10 0 0 0 01/15/CPU0[0] 10 10 10 0 0 0 01/15/CPU0[4] 10 10 10 0 0 0 01/RP0/CPU0[0] 10 10 10 0 0 0 01/RP0/CPU0[4] 10 10 10 0 0 0 01/RP1/CPU0[0] 10 10 10 0 0 0 01/RP1/CPU0[4] 10 10 10 0 0 0 0============== ======== ======== ======== ======== ======== ======== ========Global 300 300 300 0 0 0 0

Multicast Results (Last Failure)dest: FGID 1023 session_id: 31ret_code: 0 (No error)rx_ret_code: 0 (No error)tx_ret_code: 0 (No error)min_rtt_ms: 14 max_rtt_ms: 58ping_mode_mask: 0x00000011 fplane_bitmap: 0x000000ffinter_packet_delay: 0 max_timeout_ms: 1500late_timeout_ms: 1500 priority: 0flags: 0x00000000 pkt_cnt: 10pkt_size: 1000 num_nodes: 15



tx_start_ts: 11:19:47.171 UTC Fri Mar 04 2011modes: 0 - LP/fabricq0, 4 - HP/fabricq0


0/0/CPU0[0] 10 10 10 0 0 0 00/0/CPU0[4] 10 10 10 0 0 0 00/4/CPU0[0] 10 10 10 0 0 0 00/4/CPU0[4] 10 10 10 0 0 0 00/5/CPU0[0] 10 10 10 0 0 0 00/5/CPU0[4] 10 10 10 0 0 0 00/6/CPU0[0] 10 10 10 0 0 0 00/6/CPU0[4] 10 10 10 0 0 0 00/8/CPU0[0] 10 10 10 0 0 0 00/8/CPU0[4] 10 10 10 0 0 0 0

0/RP0/CPU0[0] 10 10 10 0 0 0 00/RP0/CPU0[4] 10 10 10 0 0 0 00/RP1/CPU0[0] 10 10 10 0 0 0 00/RP1/CPU0[4] 10 10 10 0 0 0 01/3/CPU0[0] 10 10 10 0 0 0 01/3/CPU0[4] 10 10 10 0 0 0 01/4/CPU0[0] 10 10 10 0 0 0 01/4/CPU0[4] 10 10 10 0 0 0 01/7/CPU0[0] 10 10 10 0 0 0 01/7/CPU0[4] 10 10 10 0 0 0 01/9/CPU0[0] 10 10 10 0 0 0 01/9/CPU0[4] 10 10 10 0 0 0 01/14/CPU0[0] 10 10 10 0 0 0 01/14/CPU0[4] 10 10 10 0 0 0 01/15/CPU0[0] 10 10 10 0 0 0 01/15/CPU0[4] 10 10 10 0 0 0 01/RP0/CPU0[0] 10 10 10 0 0 0 01/RP0/CPU0[4] 10 10 10 0 0 0 01/RP1/CPU0[0] 10 10 10 0 0 0 01/RP1/CPU0[4] 10 10 10 0 0 0 0============== ======== ======== ======== ======== ======== ======== ========Global 300 300 300 0 0 0 0

Here is an example to display detailed diagnostic test results for the FabSRCC Test:show diagnostic result <location> test FabSRCCTest detail

RP/0/RP0/CPU0:router(admin)#show diagnostic result location 0/4/cpu0 test FabSRCCTestdetailTue Jun 1 21:07:38.974 UTCCurrent bootup diagnostic level for MSC-140G 0/4/CPU0: bypassTest results: (. = Pass, F = Fail, U = Untested)___________________________________________________________________________9 ) FabSRCCTest -------------------> .

Error code ------------------> 0 (DIAG_SUCCESS)Total run count -------------> 1Last test execution time ----> Tue Jun 1 21:05:00 2010First test failure time -----> n/aLast test failure time ------> n/aLast test pass time ---------> Tue Jun 1 21:05:00 2010Total failure count ---------> 0Consecutive failure count ---> 0

Table 5: show diagnostic result Field Descriptions

DescriptionField

Test result options:

• .—Pass

• F—Fail

• U—Untested

Test results :



DescriptionField

Code for the error. DIAG_SUCCESS is indicated ifthere were no code errors. DIAG_FAILURE isindicated for any failure. DIAG_SKIPPED isindicated if the test was stopped.

Error code

Number of times the test has run.Total run count

Last time the test was run.Last test execution time

First time the test failed.First test failure time

Last time the test failed.Last test failure time

Last time the test passed.Last test pass time

Number of times the test has failed.Total failure count

Number of consecutive times the test has failed.Consecutive failure count


Loads an offline diagnostic image for integrated fielddiagnostics.

diagnostic load, on page 2





show diagnostic scheduleTo display the current scheduled diagnostic tasks, use the show diagnostic schedule command in AdminEXEC modeSystem Admin EXEC mode.

show diagnostic schedule location node-id

Syntax Description Displays the diagnostic schedule for a specified location. The node-id argumentis entered in the rack/slot/module notation.

location node-id






Usage Guidelines Use the show diagnostic schedule command to display scheduled diagnostic tasks for a specific location.


Note


Note



readdiag


Diagnostics Commandsshow diagnostic schedule

Examples The following example shows how to display scheduled diagnostic tasks:

RP/0/0RP0RSP0/CPU0:router:hostname# adminRP/0/0RP0RSP0/CPU0:router:hostname(admin)# show diagnostic schedule location 0/3/CPU0

Current Time = Tue Sep 27 12:41:24 2005Diagnostic for LC 0/3/CPU0:

Schedule #1:To be run daily 14:40Test ID(s) to be executed: 1 .

Table 6: show diagnostic schedule Field Descriptions

DescriptionField

Current system time.Current Time

Card for which the diagnostic is scheduled.Diagnostic for

Schedule number.Schedule

Time at which the diagnostics are scheduled to run.To be run

Tests to be run at scheduled time.Test ID(s) to be executed




Diagnostics Commandsshow diagnostic schedule

show diagnostic statusTo display the current running tests, use the show diagnostic status command in Admin EXEC modeSystemAdmin EXEC mode.

show diagnostic status









readdiag

Examples The following example shows how to display the current running tests:

RP/0/RSP0/CPU0:router(admin)# show diagnostic status

<BU> - Bootup Diagnostics, <HM> - Health Monitoring Diagnostics, <OD> - OnDemandDiagnostics, <SCHD> - Scheduled Diagnostics==================================== =============================== ======Card Description Current Running Test Run by------------------------------------ ------------------------------- ------RP 0/RSP0/CPU0 N/A N/A------------------------------------ ------------------------------- ------RP 0/RSP1/CPU0 N/A N/A------------------------------------ ------------------------------- ------A9K-8T/4-B 0/2/CPU0 N/A N/A------------------------------------ ------------------------------- ------A9K-40GE-E 0/7/CPU0 N/A N/A------------------------------------ ------------------------------- ------A9K-40GE-B 0/0/CPU0 N/A N/A==================================== =============================== ======


Diagnostics Commandsshow diagnostic status

RP/0/RP0/CPU0:router(admin)# show diagnostic status

<BU> - Bootup Diagnostics, <HM> - Health Monitoring Diagnostics,<OD> - OnDemand Diagnostics, <SCHD> - Scheduled Diagnostics==================================== =============================== ======Card Description Current Running Test Run by------------------------------------ ------------------------------- ------RP 0/RP0/CPU0 N/A N/A------------------------------------ ------------------------------- ------RP 0/RP1/CPU0 N/A N/A------------------------------------ ------------------------------- ------DRP 0/4/CPU1 N/A N/A------------------------------------ ------------------------------- ------DRP 0/4/CPU0 SelfPingOverFabric <OD>DRP-ACC 0/PL4/SP N/A N/A------------------------------------ ------------------------------- ------MSC 0/1/CPU0 N/A N/AJACKET CARD 0/PL1/SP N/A N/A------------------------------------ ------------------------------- ------MSC 0/6/CPU0 N/A N/AJACKET CARD 0/PL6/SP N/A N/A------------------------------------ ------------------------------- ------FC/S 0/SM0/SP N/A N/A------------------------------------ ------------------------------- ------FC/S 0/SM3/SP N/A N/A------------------------------------ ------------------------------- ------FC/S 0/SM2/SP N/A N/A------------------------------------ ------------------------------- ------FC/S 0/SM1/SP N/A N/A------------------------------------ ------------------------------- ------DRP 0/4/SP N/A N/A------------------------------------ ------------------------------- ------MSC 0/1/SP N/A N/A------------------------------------ ------------------------------- ------MSC 0/6/SP N/A N/A==================================== =============================== =====


Diagnostics Commandsshow diagnostic status

show run diagnostic monitorTo display the card type of a line card or a Shared Port Adapter (SPA), use the show run diagnostic monitorcommand in the Admin Configuration modeSystem Admin Config mode.

show run diagnostic monitor



Command Modes Admin Configuration modeSystem Admin Config mode



Usage Guidelines You need to be aware of the card type when you configure a slot or swap a card, and the configuration mustre-apply. If the card type is different, the configuration does not re-apply. You can display the card type usingthe show run diagnostic monitor command in the administration configuration mode.


read, writediag

ExamplesRP/0/0RP0RSP0/CPU0:router:hostname#adminRP/0/0RP0RSP0/CPU0:router:hostname(admin)# configRP/0/0RP0RSP0/CPU0:router:hostname(admin-config)# diagnostic monitor location 0/RP1/CPU0test FabricDiagnosisTestRP/0/0RP0RSP0/CPU0:router:hostname(admin-config)# commitRP/0/0RP0RSP0/CPU0:router:hostname(admin-config)# endRP/0/0RP0RSP0/CPU0:router:hostname(admin)# show run diagnostic monitor

diagnostic monitor location 0/RP1/CPU0 test FabricDiagnosisTest card-type 100006


Diagnostics Commandsshow run diagnostic monitor


Diagnostics Commandsshow run diagnostic monitor

Documents

Diagnostics Commands - cisco.com Commands Thismoduleprovidescommandlineinterface(CLI)commandsforconfiguringdiagnosticsonyourrouter. …