4
www.BAGelectronics.com MixedWhite Clock-Modul MixedWhite LGT-MW-01/L Operating Instructions

ClockModul DE EN - Er Elektronik · 2 BAG electronics | Clock-Modul MixedWhite General short description The Clock-Modul is used in combination with the Mixed White …

  • Upload
    tranthu

  • View
    214

  • Download
    0

Embed Size (px)

Citation preview

Page 1: ClockModul DE EN - Er Elektronik · 2 BAG electronics | Clock-Modul MixedWhite General short description The Clock-Modul is used in combination with the Mixed White …

MF 1 BAG electronics | LEDset (2Gen) interface 2014LEDset (2Gen) interface 2014 | BAG electronics

www.BAGelectronics.com

MixedWhite

Clock-Modul MixedWhite LGT-MW-01/L

Operating Instructions

Page 2: ClockModul DE EN - Er Elektronik · 2 BAG electronics | Clock-Modul MixedWhite General short description The Clock-Modul is used in combination with the Mixed White …

2 BAG electronics | Clock-Modul MixedWhite

General short description

The Clock-Modul is used in combination with the Mixed White Controller LGC-MW-01/L/plus to adjust the colour temperature and brightness of lighting systems. It is equipped with a LED display: “Automatic” (Pos. 2) and a light-sensitive diode (Pos. 1) for system programming using a smartphone. The standard set of parameters saved in the device can be viewed in the smartphone app and modifi ed to your individual requirements.

Confi guring the system

The system parameters are set with a smartphone app. Transmission of the data is via light pulses generated with the fl ash light LED of the smartphone. For transmission purposes, the fl ash light LED of the smartphone must be held at a distance of approximately 3 cm above the receiver diode (Pos. 1) on the front of the Clock-Module. Following successful transmission, the LED (Pos. 2) fl ashes 20 times, and the lighting system 3 times, for confi rmation.

Automatic mode

In automatic mode the system is controlled via parameters that are settable in the app, in accordance with time/ calculated position of the sun and/or sensors. The setting of the parameters and their functions is described in detail directly in the app and in the appropriate operating instructions.

Manual modeOperation in manual mode is via one or two connected wall push-buttons, the functions of which can be set using the smartphone app. Changing between automatic and manual mode can be implemented automatically via switching times or via connected wall push-buttons.

Page 3: ClockModul DE EN - Er Elektronik · 2 BAG electronics | Clock-Modul MixedWhite General short description The Clock-Modul is used in combination with the Mixed White …

3 BAG electronics | Clock-Modul MixedWhite

ControllerLGC-MW-01/L/plus Clock-Modul

LGT-MW-01/L10122726

Connection

•The module can be installed in the luminaire so that the LED (Pos. 2) and receiver diode (Pos. 1) are either visible at all times or are concealed in the luminaire housing.

•With concealed installation, the module must be made accessible again for data transmission if reprogramming is required.

•Double-sided sticky tape may be used for installation purposes.

Installation

Reference Order numberLGT-MW-01/L 10122726

SpecificationsSupply voltage 9 - 24 VDC SELVPower input max. 15 mAAmbient temperature ta - 20 … + 60 °CConnection to interface LGC-MW-01/L/plus RJ-10 plug, RS-485 BUS (cable length 140 mm) Max. cable length 30 m (recommendation 2 x 2 x 0.8 mm2)Dimensions (L x W x H) without cable 51 mm x 26 mm x 15 mmWeight 16 gOperating mode Automatic mode and manual modeProtection rating IP20

Technical data

Wiring diagram

•Only one controller must be connected to one clock module.•The connection is established via the fixed cable with RJ-10 plug.•The cable can be expanded to up to 30 m with corresponding

extensions.•A supplementary sensor module can be connected using a

Y-distributor.

Connection of components

Pos. 1 Receiver diode for data transmission

Pos. 2 LED display: “Automatic”

Page 4: ClockModul DE EN - Er Elektronik · 2 BAG electronics | Clock-Modul MixedWhite General short description The Clock-Modul is used in combination with the Mixed White …

4 MF BAG electronics | Clock-Modul MixedWhiteBAG electronics | Clock-Modul MixedWhite

[email protected]

HeadquartersBAG electronics GmbH Kleinbahnstraße 2759759 ArnsbergGermanyTel: +49 2932 9000 9800Fax: +49 2932 9000 9796

BAG electronics Von-dem-Bussche-Münch-Straße 1232339 Espelkamp, GermanyTel: +49 2932 9000 9800Fax: +49 2932 9000 9796

BAG electronics Sales Office MilanoVia Cavriana 320134 Milano, ItalyTel: +39 0 2739 1274Fax: +39 0 2739 1410

BAG electronicsSales Office LondonUnit 2, Winsford Way, Chelmsford, Essex, CM2 5PD United KingdomTel: +44 1245 469935Fax: +44 1245 462646

BAG electronics (India) Pvt. Ltd. S.No 19, Yewlewadi, Kondhwa RoadPune 411 048, IndiaTel: +91 20 3045 0702Fax: +91 20 3045 0800

BAG electronics (GuangZhou) Ltd.Room 1009, Yian PlazaJianshe liu Road, Yuexiu dis tric, Guangzhou Post Code: 510600, ChinaTel: +86 20 3836 1176Fax: +86 20 3836 1177 BAG electronics (HK) Ltd.Unit 3, 9/F, Hopeful Factory Centre, 10-16 Wo Shing Street, Fotan, Shatin, New Territories , Hong KongTel: +852 2307 6292Fax: +852 2370 9098

BAG electronics Inc. Laguna International Industrial ParkBlock 5 Lot 7, CNB Street, 4024 Mamplasan, Biñan, Laguna, PhilippinesTel: +63 49 539 0743Fax: +63 49 539 0740

Technical modifications reserved.2015-02 Clock-Modul MixedWhite