Cladding Cladding & Shading Sector Product Guide · global contractors to local landscapers. The Cladding and Decking ranges are available in the UK through International Timber and

Industrial Rail Marine Decking Cladding

...designed for the future

Cladding & Shading Sector Product Guide

Composite cladding and pergolas for domestic properties, commercial buildings, offices and factories.

Cladding

Commercial

Type 150 Weatherboard Barn Black PAGE 11

Solar Shading Cladding PAGE 21

Type 200 Flush Teak PAGE 7 Vertical Cladding PAGE 17

Ideally suited for all new build or refurbishment projects including:

• Commercial buildings such as Hotels, Factories, Schools or Offices• Mixed Use Developments & Residential Complexes• Barn Conversions• Individual Domestic Properties• Garages & Outbuildings

Contents

Domestic

Exterior Wall Cladding 3

Product Range Selector 4

Flush Range

Type 150 Flush 5

Type 200 Flush 7

Type 250 Flush 8

Weatherboard Range

Type 150 Weatherboard 9

Accessories 11

Essential Guide - Dura Cladding 13

Preparation & Installation 15

Colour Visualiser 18

Solar Shading Cladding 19

Composite Timber Pergolas 23

Type 150 Flush Grey PAGE 5 Type 150 Flush Cedar PAGE 5

The Dura Composites range of composite cladding is suitable for a wide variety of domestic and commercial applications. The products offer the rare combination of a natural wood look allied to colour fade resistance and are an attractive, hard-wearing and low maintenance way to finish or complement the exterior of both new and refurbished buildings.

About usDura Composites Ltd. is a leading global supplier of high performance composite cladding, flooring and structures which are ideal for the architectural, landscaping, industrial, marine and rail sectors as a long-lasting and cost-effective replacement for wood, steel and concrete.

Our UK Headquarters is dedicated to innovation and ensures that Dura Composites is always at the forefront of composite material technology. Our growing team have extensive knowledge and practical experience of timber composites, fibreglass reinforced plastic and other related emerging materials.

The range of products on offer is vast, from composite cladding, decking and fencing through to floor walkway grating, lift risers and trench covers. All products are designed to offer a low life cycle cost thanks to their low maintenance requirements and long life expectancy.

Dura Composites’ solutions are used by a wide range of customers – from global contractors to local landscapers. The Cladding and Decking ranges are available in the UK through International Timber and are 100% Forest Stewardship Council® (FSC®) certified.

Mission Statement

To supply pioneering composite product solutions to real-world problems for customers in the industrial, rail, marine, landscaping & architectural sectors.We do this by focusing on continuous innovation, a relentless drive to understand the specific needs and operating environments of our customers and a commitment to exceptional service and care.

To help us achieve our strategic vision, we will harness our global network of highly satisfied, passionate and connected customers to drive awareness of Dura as the experts in composite product solutions.

We will also provide the leadership and support necessary to ensure that our employees are empowered, challenged, happy and rewarded - in recognition of the importance of their contribution to our continued growth and success.

Dura Composites’ products are also available through a well-established global distribution network in the Middle East, Africa and Europe.

Vision

To be revered globally as experts in the creation and supply of breakthrough composite product solutions - offering a scalable, performance improving and cost-effective alternative to traditional materials.

1 www.duracomposites.com

Type 150 Flush in Cedar installed vertically

Type 150 Flush Cladding in use at Tennis Facility

Why Choose Composite?

2www.duracomposites.com

InnovationBy listening to our customers and understanding their needs we have developed a range of products and accessories that add value throughout the supply chain. Our Composite Timber is manufactured by an extrusion process and uses a mix of recycled plastics and hardwood which are combined with bespoke additives to produce attractive and long-lasting results.

Lower Maintenance Unlike traditional timber, Composite Timber from Dura Composites requires no staining or painting and won’t warp or rot. With only basic cleaning required, the product still looks new after years of use and remains cost-effective over its lifecycle.

The Dura Composites architectural range is manufactured from a unique combination of wood and plastic which creates a Composite Timber. This highly developed precise composition combines the traditional appearance of timber with the durability of an engineered composite. It results in a vibrant, long-lasting colour which will never rot and does not require staining or painting unlike traditional hardwood. The products are suitable for both domestic applications such as exterior cladding, balconies or decking and for the most demanding commercial applications such as louvre screening, boundary fencing, exterior building cladding, decking and pergolas.

DurabilityOur Composite Timber is an immensely versatile material which combines the traditional appearance of timber with the durability and resilience of an engineered composite. We offer a 10 year warranty and all our products have an expected 25 years service life.

AppearanceThe unique manufacturing process used to produce our Composite Timber allows for the creation of a wide range of attractive colours that can easily rival traditional timbers. The products are colour stable with only minimal initial weathering and are the eco-friendly choice, with up to 87% recycled materials and 100% Forest Stewardship Council® (FSC®) certification.

Whilst timber has traditionally been used for cladding and pergolas, the emergence of Composite Timber has delivered a host of advantages over traditional materials and have led it to become the number one choice for architects and specifiers looking for an attractive but futureproof solution. Strong and durable, Dura Cladding, Dura Louvre and Dura Pergola look and feel just like natural wood, but provide a longer-lasting solution that is environmentally friendly, easy to install and requires minimal maintenance.

Dura Cladding provides an attractive and long lasting finish

Dura Cladding is available in a range of colours


Dura Cladding is made using a highly developed extrusion process and has a unique timber and plastic composition. Recycled high density polyethylene polymers, recycled ground hardwoods and specifically engineered additives are harnessed together with high performance coupling agents to provide beautiful low maintenance 87% recycled and 100% Certified FSC® wall cladding. Dura Cladding provides the client with a traditional wood cladding appearance coupled with a 25 year design life and a fraction of the maintenance costs of natural wood.

High Strength To Weight Ratio Permanent Colour Rot, Splinter, Warp Resistant Easy Installation Weather Resistant Fire Resistant Simple Cutting And Site Install UV Colour Stable 100% Certified FSC®

No Knots

Easy Handling Colour Stable No Painting And Staining No Specialist Skills Required 10 Year Warranty Euro Class Bfl-S1 Certified Only Requires Standard Tools Looks Good Through Lifespan Eco Friendly Few Wasted Planks

Offices & Factories Private / Public Buildings Screening Architectural Fascias Commercial Premises Warehouses Display Areas Outbuildings & Workshops

Applications

Features

Benefits

Dimensions

Material Specifications

Exterior Wall CladdingDura Cladding

Cladding Plank Plank ActualPlank Maximum Weight Profile Thickness Length Width FixingSpan l/m

Type150Flush 21mm 3600mm 150mm 600mm 2.04kgType150Weatherboard 21mm 3600mm 150mm 600mm 2.34kgType200Flush 21mm 3600mm 200mm 600mm 3.14kgType250Flush 21mm 3600mm 250mm 600mm 3.75kgStarterTrim 21mm 3600mm 60mm 600mm 1.21kgFinishingTrim 38mm 3600mm 154mm 600mm 2.7kgExternal/Internal/ExpansionTrim 38mm 3600mm 139mm 600mm 4.11kgTrimInsert 14mm 3600mm 28mm 600mm 0.24kgFasciaTrim 9mm 3660mm 230mm - 2.88kgFasciaTrim 10mm 3660mm 140mm - 1.94kg

Characteristics Unit TestReference

TensileStrength 15mpa BS6399ImpactStrength 8kj ASTMD1037-93FlexuralStrength 3.15gpa ASTMD1037-93FlexuralStrength**** 3.13gpa ASTMD1037-93UVAgingTest Pass ISO4892-2Density 1.4g/cm3 Ceram,StokeonTrent24HourWaterAbsorption 1.07% ASTMD684FlammabilityResistance EuroClassDfl-S1 BSEN13501-1(TBC)FireResistance Pass 476Part7Class3ExpansionRate 3.882E-US(K-I) Ceram,StokeonTrentWeatherability NoDamageat100cycles MOAT22ThermalConductivity 0.154W/m.K. IndicativeresultMaximumThermalExpansionRate* 0.038mm/min/°change ESGReportM5703R1Rev1MaximumThermalContractionRate** 0.036mm/min/°change ESGReportM5703R1Rev1FrostResistance NoDamage DDCEN/TS772-22:2006StructuralWindLoad-Negative <654.86kg*** ESGReportM5703R1Rev1StructuralWindLoad-Positive <2308.6kg ESGReportM5703R1Rev1Sustainability FSC®certification FSC®100%CertificationRecycledcontent Minimum83%recycled Ceram,Carbonfootprintreport*From60to80°C**From70to30°C***DuraCladdingexceededthetestrigcapacity****AfterUVaging(1000hours&rain)


Product Range Selector

Exterior Wall Cladding

Dura Cladding is available in both flush and weatherboard styles and in 3 widths from 150mm to 250mm ‘face’ coverage. The availability of wider planks provides a striking finish and also benefits from reduced installation times, making them ideal for use on larger buildings. There are several attractive colours to choose from, as shown in the table below.

The difference between Flush and Weatherboard

Type 150

Flush Range WeatherboardRange

Plank Strength

MEDIUM

Install Speed

MEDIUM

Recycled Content

Up to 87%

Typical Applications

Domestic PropertyResidential Projects

Colours

TeakCharcoalCedarGrey

Plank Strength

MEDIUM

Install Speed

FAST

Recycled Content

87%


Residential ProjectsCommercial ProjectsFactoriesOffices

Colours

Teak

Plank Strength

STRONG

Install Speed

VERY FAST

Recycled Content

85%


Residential ProjectsCommercial ProjectsFactoriesOffices

Colours

CedarGrey

Plank Strength

MEDIUM

Install Speed

MEDIUM

Recycled Content

87%


BarnsOutbuildingsCart LodgesSheds

Colours

Barn Black

Type 200 Type 250 Type 150

Dura Cladding is suitable for both domestic and commercial new build & refurbishment projects and can be laid horizontally with overlapping or flush faces or vertically for those projects which require a different aesthetic.

Weatherboard or Featheredge cladding is an ideal solution for those who prefer a traditional appearance and is typically used on barns, outbuildings, lodges and sheds. Available in Barn Black colour in boards of 150mm, the cladding is designed to be laid horizontally with an overlap and has an attractive rustic look.

In the Flush range, Dura Cladding comes in a range of other attractive colours and sizes ranging from 150mm to 250mm. Dura Composites Flush Cladding has modular fixings that enable the cladding to be flush to the wall.


Flush Range



Type 150 Flush

Dura Cladding Type 150 Flush provides an attractive hardwearing, protective layer against the elements and is an excellent insulator.

Type 150 is available in Cedar, Charcoal, Teak and Grey to suit any application.

Type 150 in Cedar shown with external trim

Type 150 in Teak shown alongside Dura Deck

Type 150 in Cedar

Cedar

Charcoal

Teak

Grey

Dimensions

174 3

21

150 Face

150 150 150

All measurements are in millimetres


Type 200 Flush

Dura Cladding Type 200 Flush is available in Teak and looks and feels just like natural wood. Dura Composites unique Composite Timber formula produces a longer lasting cladding that is environmentally friendly, easy to install and requires minimal maintenance.

Exterior hotel façade using Dura Cladding Type 200 Flush in Teak

Teak

225 2

21

200 Face

200 200 200

Dimensions


Dura Cladding in use within a station canopy Type 200 Flush in Teak



Type 250 Flush

Dura Cladding Type 250 Flush is available in two attractive colours – Cedar and Grey.

All our cladding products are UV Certified to ISO 4892-2, meaning that after the initial expected weathering they will survive even the harshest of climates.

Company Head Office façade utilising vertical flush cladding in Type 250 Cedar

Cedar

Grey

250 Face

275 3

2

2140.1

250 250

Dimensions


Dura Cladding Type 250 Flush in Cedar Type 250 Flush in Grey


Weatherboard Range

The difference between Flush and Weatherboard?

Weatherboard or Featheredge cladding is designed to be laid horizontally with an overlap and has an attractive rustic look. The Flush range is available in a variety of different sizes and has modular fixings that enable the cladding to be flush to the wall.


Type 150 Weatherboard

The Dura Composites Weatherboard or Featheredge cladding is ideal for those applications where a traditional appearance is preferred, such as barns, outbuildings, lodges or domestic properties.

Weatherboard cladding is designed to be laid horizontally with an overlap and has an attractive rustic look. A wide range of WPC trims and accessories are available to complement any design.

Type 150 Weatherboard is equally attractive when used on domestic or commercial buildings


Barn Black

A stylish mix of rendered and Type 150 Weatherboard cladded walls can harmonise the overall look of a property’s exterior and improve warmth and energy efficiency.

150

Dimensions

174 3

1

21

150 Face

150 150


BEFORE

AFTER



Accessories

Starter Trim Finishing Trim

Internal, External, Corner and Expansion Trim

A comprehensive range of trims and accessories are available to complement your Dura Cladding design. For more information about how to prepare and install Dura Cladding, please consult the free supporting Technical Manual available on our website or from your Dura representative.

Our trims provide the finishing touches to ensure a professional, clean look for your composite cladding.

Our range of complementary trims can be cut to size to suit window or door frames.

Internal, External and Expansion Trims provide a professional finish whilst allowing the composite cladding to expand and contract with the changing environment.

Internal / External Trim Starter Trim Finishing Trim



Trim Insert

Fascias

End Caps and PlugsThe trim insert allows for quick installation and covering of fixings, ensuring a neat finish to your cladding project.

Fascia boards can be easily incorporated into any design and allow for the creation of a maintenance free roofline.

Fascia trims are available in 2 sizes, depending on colour:

230mm x 9mm (Cedar, Barn Black, Charcoal & Teak)

140mm x 10mm (Grey)

Our end caps clip in easily to the end of cladding planks to give your cladding a clean edge.

Dura Composites’ Cladding Trims are multi-purpose and should be cut at the relevant point using our handy reference guide.

Trim insert position End caps Fascia

When to use Fascias



Our Essential Guide to Getting the Most From Your Dura Cladding

Whether you’re planning a commercial, residential, new-build or refurbishment cladding project, Dura Composites has a durable, simple to install, cost-effective and environmentally

friendly solution to meet your needs.

Our high-performance composite cladding delivers a host of advantages versus traditional materials and is the number one choice for architects, specifiers and

homeowners looking for an attractive but futureproof solution. To ensure you get the best results, we recommend working with a professional contractor with previous cladding installation experience. Please ensure that the guidance provided below

and in our supporting Technical Install Manual are strictly adhered to as improper installation (including the use of the use of non-approved trims, fixings and accessories) will invalidate your product warranty.

To activate your product warranty after purchase, please complete the online form at www.duracomposites.com/warranty/

When planning your Dura Cladding, please bear in mind the key considerations opposite.

To download the Dura Composites detailed Technical Manual, please visit:www.duracomposites.com/cladding/installation-manual



Our Essential Guide to Getting the Most From Your Dura Cladding

Before installing any cladding product, you should review local building codes and regulations, and consult with local building officials to ensure compliance and safety. Dura Composites

recommends that all cladding designs be approved by a licensed architect or engineer prior to installation. Wear protective clothing and safety equipment where necessary

such as safety glasses, gloves, dust masks and long sleeves, particularly if cutting in confined spaces. Refer to the operator’s manuals for safety guides for all power tools used.

Dura Cladding is ideal for both domestic and commercial new build & refurbishment projects and can be laid horizontally with either overlapping or flush faces or vertically for those projects which require a different aesthetic. In the Flush range, Dura Cladding comes in a range of other attractive colours and sizes

ranging from 150mm to 300mm.

Weatherboard or Feather-edge cladding is an alternative solution for those who prefer a traditional appearance and is typically used on barns, outbuildings, lodges and sheds. Available in Barn Black colour in boards of 150mm, the cladding is designed to be laid

horizontally with an overlap and has an attractive rustic look. Once you have decided where you want your cladding situated, measure the length and width of the total area. Cladding is installed horizontally as standard, but Dura Cladding can also be installed vertically to provide a different final look.

Extremely warm or cold outdoor temperatures play a significant role in the installation and performance of all cladding products. Following the detailed installation instructions in our supporting Technical Manual

will help manage and reduce the effects of thermal expansion and contraction. Please refer to the gap guide in our Technical Manual to ensure your planks have adequate space for expansion and contraction and

to preserve the service life of your cladding. Please ensure that you allow Dura Cladding to acclimatise to the exterior temperature before cutting and installing.

Once you have completed the install of your Dura Cladding, we advise that the cladding is either washed down thoroughly with a yard broom or pressure washed to ensure that a good clean surface is ready for you to enjoy.

Basic CleaningSpray with a hose to remove

surface debris. Use warm soapy water and a soft-bristled brush to clear dirt and/or debris from grooves or contours.

Pressure WashingPressure washers up to 1500psi may be used to maintain cleanliness of timber composites. In order to prevent

any damage, always keep the pressure washer nozzle at least 15cm (6 inches) from the surface, and avoid concentrated spraying on one area for more than 3 seconds. The use of a pressure washer in this manner will not shorten the life of the material.

To ensure the best performance of our products, it is vital that proper care and attention is given to storage and handling of materials. Please ensure you adhere to the following guidance:

● Store the products on a flat and level surface in their original packaging until you are ready to install them. ● If stored outdoors the products must be kept in a covered area to prevent exposure to direct sunlight and weathering.

● Take care to ensure that boards are not stacked adjacent to sources of moisture.● Professional fork lifts should always be used while uploading and discharging pallets. Pallet stacking should not exceed 4 pallets maximum.

1. Safety First

3. Choose the Right Product for Your Needs

4. Thermal Expansion and Contraction

5. Care & Maintenance

2. Storage and Handling

SAFETY FIRST SAFETY FIRST

STO

RAGE & HANDLING

STO

RAGE & HANDLIN

G

RI

GHT PRODUCT RIGHT PRODUCT

THER

MAL EXPANSION

THERMAL EXPANSIO

N

CAR

E & MAINTENANC

E CARE & MAINTENANC

E


STO

RAGE & HANDLING

STO

RAGE & HANDLIN

G

RI


THER

MAL EXPANSION

THERMAL EXPANSIO

N

CAR

E & MAINTENANC

E CARE & MAINTENANC

E


STO

RAGE & HANDLING

STO

RAGE & HANDLIN

G

RI


THER

MAL EXPANSION

THERMAL EXPANSIO

N

CAR

E & MAINTENANC

E CARE & MAINTENANC

E


STO

RAGE & HANDLING

STO

RAGE & HANDLIN

G

RI


THER

MAL EXPANSION

THERMAL EXPANSIO

N

CAR

E & MAINTENANC

E CARE & MAINTENANC

E


STO

RAGE & HANDLING

STO

RAGE & HANDLIN

G

RI


THER

MAL EXPANSION

THERMAL EXPANSIO

N

CAR

E & MAINTENANC

E CARE & MAINTENANC

E


Installation Vertical Cladding

Getting started - Our Simple Install GuidePreparation

Step 1: Place the Internal Trim in position at the bottom batten. Screw into the middle of the trim.

Step 4: Keep on doing this until you reach the end. Use Internal Trim at the top, position on Batten and attach with screws.Slide in the Trim Inserts at the Top and Bottom Trims.

1. Decide on which direction the cladding will be installed:It is possible to install Dura Cladding in either direction, both vertical and horizontally. Measure the length and width of the total area. As standard, any cladding should be installed horizontally. However, it is also possible to install vertically.

2. Select the area to be clad and produce a bill of quantities:Before you finalise your order, it is best to choose exactly which parts of the building that you wish to clad with Dura Cladding, how large it will be, and which cladding

planks and which trims you will require. Normally, it is best to produce a bill ofquantities based on a CAD layout taking into account the actual plank lengths available. This is something that we may be able to help with subject to sufficient time and information. Most customersfind that it is wise to build in a waste factor of 7-10% to account for the inevitable quantity of material that cannot be used due to cutting - this may be more or less depending on the number of cuts required to fit awkward shapes. By taking these factors into account, it is more likely that all of your planks can be delivered on a single load.

3. Preparing the battening:Now that you know the direction of the cladding and the exact area of your cladding, next you must determine the batten layout. It is most common to use timber battens although other approvedwall batten materials can be used so long as they are fixed to the building using a suitable fixing system. Each Dura Cladding plank must be supported every 600mm. Extra care is required in order to provide sufficient battening in and around obstacles such as windows, fascias, etc.

Step 2: Position External Trim so it lines up with the Internal Trim and secure to battening. Screw in Centre of grooves.

Step 5: Use External Trim, cut to size and secure with screws. If cladding carries on round corner, make sure ExternalTrim lines up with battening. Slide in the Trim Insert.

Step 3: Place the first Cladding Plank at the end and secure in the middle of the elongated holes.

Step 6: If your cladding carries on around a corner, follow Steps 1 through 5. Make sure the External Trim is in the right position, so as to place the CladdingPlank into the right position.


1

4 5 6

2 3


InstallationHorizontal Cladding

Step 1: Fix the Starter Trim to the batten. The screw should be positioned in the centre of the slotted hole. Do not overtighten as this will restrict expansion and contraction.

Step 4: Cut the internal trim as per the cutting guide. Position the Internal Trim and mark on battens to show where planks will finish. Position cladding approx. half way into recess. Fix using an 8G A4 Stainless Steel Pan Head Screw, 50mm in length. Push the trim insert into place.

Step 7: Optional Soffit Detail: In instances where a soffit return is required, our unique starter trim can also be used as a soffit detail to create a neat finish. As each project circumstance will be different, please ensure that you contact us to check suitability prior to installation.

Step 2: Place the first plank in the Starter Trim ensuring the hole centres line up with the battens. Again, do not overtighten as this will restrict expansion and contraction.Repeat this process, checking the levelbefore each plank is fixed.

Step 5: Cut the expansion trim as per the cutting guide. Place into position.Fix using an 8G A4 Stainless Steel PanHead Screw, 50mm in length.

Step 3: Cut the external (Corner) trim as per the cutting guide. Place trim in position and mark on the battens to show where planks finish. Position Cladding approx. half way into recess. Fix using an 8G A4 Stainless Steel Pan Head Screw, 50mm in length. Push the trim insert into place.

Step 6: Cut a Finishing Trim to size by marking where cuts are needed. Mitering and buttjoining is acceptable. Mark batten centres and drill oversized holes (12mm) through top surface. Drill a 6mm hole and carbon burr to elongate hole. Fix the Trim through the second skin using 8G A4 Stainless Steel Pan Head Screw, 25mm in length. Insert plug and clean with chisel and sandpaper (40 grit abrasive). Fascia trims can be cut down to size to suit windows or door frames and these can be cut from our standard solid fascia board.

Step 8: It is unlikely that cladding installed horizontally on the wall will terminate on a full width plank. If this is the case it maybe necessary to cut the last plank down in width. There are a range of options available, subject to individual site conditions. Please consult our detailed Technical Manual for more details on possible scenarios for finishing the last plank.


1

4

7

5

6

2 3

Case Studies

Green Park is a 20 acre, mixed-use business park consisting of prime office, industrial and leisure space in Newport, East Yorkshire. Green Park provides local companies in East Yorkshire with modern and energy efficient business space in the right location – benefits that are usually only reserved for large organisations. The developer behind the concept is the Horncastle Group who along with their architects, The Harris Partnership, selected Composite Timber Dura Cladding in Type 150 Cedar as the exterior wall covering in recognition of its low maintenance and environmentally friendly properties. Speaking about the project, Ian Hodges, managing director of Horncastle Group PLC said; “The overarching concept behind the development was to ensure it was as architecturally attractive, environmentally friendly and sustainable as possible, and selecting Dura Cladding for the exterior

walls has played a significant role in helping us achieve that. The resulting buildings look great, are extremely energy efficient and all have Energy Performance Certificate ratings of A. Dura Cladding offered all of the key properties we were looking for in terms

of its appearance, low-maintenance, environmental sustainability and long term durability, and was a great choice from our point of view. In fact, we’re so delighted with the results that Horncastle Group recently relocated to Green Park Business Park to help establish a business community in this prime location.”

Hopewood Park is situated in Ryhope, Sunderland and provides a range of clinical services including assessment and treatment of mental health conditions and services for people who require intensive rehabilitation. The £50 million facility was designed by Medical Architecture and was inspired by Ryhope’s river valley.

The layout and design of Hopewood Park encapsulates the latest thinking and approaches to mental healthcare, creating a sympathetic and soothing recovery-centred environment both inside and out, with plenty of exposure to daylight. A calming range of textures and finishes in a restrained pallet of white, composite wood, grey and slate have been used both internally and externally, creating an ‘outside is inside’ feeling to the buildings.

To achieve the wood-effect finish Dura Cladding composite timber in Type 150

Cedar Flush was selected. This pretty and authentic wood-effect cladding offers greater longevity than traditional wood. The use of Dura Cladding also helps enhance the feeling of tranquillity and connection with the local landscape

whilst ensuring a low-maintenance finish that won’t rot, fade or change colour over time. The product also offers fantastic green credentials – it is made from 87% recycled content and can be supplied as FSC® 100%.

Green Park Eco-Offices

Hopewood Park



Type 150 Cedar Flush vertically installed

Type 150 Cedar Flush horizontally installed

Colour Visualiser



Our online cladding visualiser tool can help builders, contractors, developers and architects to picture the possibilities when it comes to composite timber cladding.

The simple to use tool allows users to select from sample commercial and domestic projects which utilise both vertical and horizontal cladding in a range of designs. With one simple click of the mouse, clients can explore differing width options and a wide range of colours to suit a variety of project needs.

Trial the Colour Visualiser now on our website at www.duracomposites.com.

Type 150 Weatherboard Barn Black

Type 150 Flush Cedar

Type 200 Flush Teak Type 150 Flush Grey

Type 250 Flush Cedar

Type 150 Flush CharcoalType 150 Flush


Dura Louvre provides an aesthetic design solution to protecting a building against extreme solar influence, or to covering unsightly areas whilst still maintaining desirable daylight.

Made of composite timber, Dura Louvre can help reduce the thermal heat in south-facing buildings as well as reducing energy costs by minimising air conditioning requirements. It can also be used effectively to screen pipework, utilities and other areas from view.

Dura Louvre solar shading cladding can be integrated into new builds or added to existing properties and will transform the exterior of any building.

Dura Louvre Cladding combines style with a range of clever benefits such as privacy, weather protection, energy efficiency and ventilation.

Dura Louvre Cladding is available in Cedar and Charcoal colours in 140/40mm profiles as standard. Other colours and profiles are available on request.

UV Colour Stable Rot, Splinter, Warp Resistant Easy Installation Weather Resistant Fire Resistant 100% Certified FSC®

Easy Handling No Painting And Staining No Specialist Skills Required 10 Year Warranty Looks Good Through Lifespan Eco Friendly

Solar Shading for Offices & Commercial Buildings Screening of Unsightly Areas Protective Wall Covering Ventilation New Finish for Existing Buildings

Applications Features Benefits

Solar Shading CladdingDura Louvre

Specifications

Cladding Plank Plank ActualPlank Maximum Weight Profile Thickness Length Width FixingSpan l/m

Type140/40Louvre 40mm 3660mm 140mm - 5.01kg

The composite timber fins can be fitted horizontally or vertically


Solar Shading Cladding



Louvre systems are also sometimes known as Brise Soleil and are designed to provide effective shading and screening solutions to buildings. Dura Louvre Cladding combines the natural appearance of wood with the durability and low maintenance properties of composites.

The application of solar shading cladding can reduce solar gain in summer or hot weather conditions. This saves air-conditioning costs and allows solar heat gain in winter, thereby saving heating costs.

Dura Louvre Cladding provides effective shade to glazed openings, preventing excessive glare and solar heat gain, but it also creates a striking architectural feature. Solar shading Dura Louvre panels can be integrated into new buildings or added to existing properties. Some examples of Dura Louvre used as window shading are shown below and right:

Horizontal Solar Shading

Normally fitted above windows with either horizontal or sloping supports where the blades are horizontally stacked and set at the optimum position to suit each building and its orientation to the sun.

Louvre Cladding Options



Vertical Solar Shading

Normally fitted to vertical posts in front of windows where the blades are vertically stacked and set at the optimum position to suit each building and its orientation to the sun.

Bespoke Screening

Screening louvres can be used in locations where rain penetration is acceptable, or the location is sheltered from adverse weather conditions. They are often used to conceal HVAC systems or to help hide unsightly equipment whilst enabling the passage of air to plant machinery.

To fix Dura Louvre, a simple bracket sleeve is used to fasten the cladding to the substructure. The brackets are fixed to the substrate at set vertical or horizontal separations, and the Dura Louvre profiles are then fixed into the brackets. Various bracket sizes are available in both Cedar and Charcoal. Available dimensions and configurations are shown below and right:

Dura Louvre Bracket Options


15 15 15

15

15

1515

15

120150

180210

230

270

75

75

5013

38

6.5mm slots for steel or timber frame

11mm slot for blockwood/concrete

Dimensions


Composite timber Dura Pergolas have a unique formula that provides the very best of both worlds, a long lasting material that is strong, durable and weathers extremely well. Composite timber Dura Pergolas are striking yet have traditional appearance, require little maintenance and will not splinter. The material is UV stabilised and above all eco-friendly with a 87% recycled material content.

No painting or staining UV resistant Colour stable Minimal maintenance Does not splinter Long life span Eco-friendly

Hassle free Suitable for extreme climates Aesthetically pleasing Requires only basic cleaning Touch Safe Futureproof Solution with expected

25+ year service life

Beach Areas Hotel Buildings Hotel Gardens Roof Gardens Theme Parks Villa Complexes Parking Areas

Applications

Specifications

Sample Designs

Features Benefits

Composite Timber PergolasDura Pergolas

Product Width Length Height Weight(Kg) SlatSpansType33 3000mm 3000mm 3160mm 692 260Type43 4000mm 3000mm 3160mm 788 260Type53 5000mm 3000mm 3160mm 856 260Type44 4000mm 4000mm 3160mm 788 260Type844(4Post) 8000mm 4000mm 3160mm N/A 260Type846(6Post) 8000mm 4000mm 3160mm 1328 260Type99 9000mm 9000mm 3160mm N/A 260

A classic pergola structure

Dura Pergola on a veranda in Qatar

9000

3000

50008000 8000

40004000

9000

290

290

290 290 290

3000

3000 4000 4000

3000 4000

290 290


Type 99

Type 53

Type 90

Type 844 Type 846

Type 43 Type 44


Our Pergolas and other outdoor structures provide shade, protection from the elements, and a place for outdoor entertainment.

Choose from one of our pre-designed Dura Pergola structures or let our expert team help create your bespoke pergola, gazebo or cabana design.

Composite Timber Pergolas

Add shade and ambience with a Dura Pergola

Dura Pergolas can completely transform the look of a deck or patio Pergolas can define space and add interest to an area

Dura Pergolas in verandas at SEG Doha University Campus

Industrial Rail Marine Decking Cladding

...designed for the future

Head Office

Dura Composites LtdDura House, Telford RoadClacton On SeaEssex, CO15 4LPUnited Kingdom

Due to our policy of continual improvement we reserve the right to change specifications at all times without prior notice.

Tel: +44 (0)1255 440299Fax: +44 (0)1255 435426Email: [email protected]

www.duracomposites.com

Cladding

Available now from

July 2016

Sole UK Timber Importer

Grangemouth (Scotland) Sales Centre

Tel: 0844 723 0321Fax: 01324 665464Email: [email protected]

Trafford Park (Northern) Sales Centre

Tel: 0844 728 0341Fax: 0161 848 2901Email: [email protected]

Parkend (South West & Wales) Sales Centre


Purfleet (London & South East) Sales Centre


www.internationaltimber.com

Documents

Cladding Cladding & Shading Sector Product Guide · global contractors to local landscapers. The Cladding and Decking ranges are available in the UK through International Timber and