Chemistry Lab Manual

Chemistry Lab Manual

Tenafly High School

September 2010

7th edition (sh)

Lab #

CHEMISTRY LAB - ACTIVITY TITLES

Page

1

Lab Safety

5

2

Matter Classification

7

3

Classifying Physical and Chemical Changes

9

4

ChemicalPropertiesof Four Liquids

11

5

Density ofPennies

13

6

Percent Cu inPennies

15

7

Law of Definite Composition

17

8

Particle SizeProbability

19

9

EmissionSpectroscopy

21

10

FlameTest

23

11

Electron Probability An Analogy

25

12

Mendeleev for a Day

27

13

Periodic Trends: Alkali Metals

29

14

Ionic and MolecularCompounds

31

15

Models of Covalent Compounds

33

16

Chemical Name andFormula Writing

35

17

Composition of Hydrates

37

18

Aluminum Foil

39

19

Empirical Formula

41

20

Single Replacement Reactions

43

21

Double Replacement Reactions

45

22

Four Solution Problem

47

23

Types of Reactions

49

24

Moles Fe and Cu

51

25

Mole-Mass Relationship

53

26

Changes in Physical State

55

27

Boyle's Law

57

28

Determination of Absolute Zero

59

29

Molar Volume of Gas

61

30

Paper Chromatography

63

31

Ice Cream Lab

65

32

Rate of a Reaction

67

33

Investigation of Chemical Equilibrium

69

34

Change in Enthalpy of a Reaction

71

35

pH and Indicators

73

36

Acid Base Titration

75

37

Understanding Half-life

77

38

Determining the Half-life of Ba-137m

79

39

Back to Chernobyl

81

1. LAB SAFETY

Welcome to Chemistry. The first order of business is to familiarize yourself with the lab room you will be working in. This safety activity will review rules you are familiar with and introduce you to new ones rules which are unique to Chemistry. At the culmination of this lab, you and your parent/guardian will read and sign a safety contact. You will be held responsible for performing and behaving in a safe manor throughout the year. You will be required to pass the safety quiz before performing any other labs.

PRE-LAB QUESTIONS

1. Set up your lab notebook as specified by your teacher. 2. What is the purpose of this lab activity?

OBJECTIVE 1. Familiarize yourself with safety equipment in the classroom.2. Review safety rules.3. Conduct safety orientation activities4. Formulate safety rules

MATERIAL7 stations with posted questions

PROCEDURES1. Start at the station where you are seated. Stations can be done in any order.

2. Stay with your lab table group. Read the question on the card. 3. Perform the activity as stated and record information on the data table.4. When group is ready, switch to the next station.

STATION QUESTIONS/ACTIVITIES

1. What is the effect of acid on clothing? GOGGLES AND GLOVES ARE REQUIRED

2. What is the effect on acid on skin or eyes? GOGGLES AND GLOVES ARE REQUIRED

3. How do you safely light a Bunsen burner? GOGGLES REQUIRED

4. Can all these materials be used to run an experiment?

5. Why is this not a safety station?

6. What is wrong with this lab station?

*7. Identify each piece of equipment. Give brief description of their use. Record.

CONCLUSION

1. Complete data table.

2. State at least one safety rule associated with each station (6 rules).

2. Classification of Matter

Introduction: There are many ways to classify or group matter. Chemists have agreed upon a general system of classification. After you become familiar with the terms you will examine different samples and classify them.

DO NOT OPEN VIALS

PRELAB1. What is the purpose of this activity2. Define the vocabulary words on the chart provided.

Procedures:1. Working in lab groups as assigned by your teacher.2. Exam the sample in the vials. Do not open the bottles.

3. In the chart provided, describe some physical characteristics (color, shape, phase), then indicate the state of matter as: S = solid, L = liquid, or G = gas.4. Sort the substances into similar groups. (Example: all the elements ..). Conclusion:1. Fill in the conclusion chart, by listing the substance in one of five groups.

3. CLASSIFYING PHYSICAL AND CHEMICAL CHANGES

There are two types of changes that occur in nature: physical and chemical. In a physical change, one or more physical properties of a substance are altered but the composition remains the same. No new substances are formed. A chemical change results in the formation of one or more new substances. These new substances differ in chemical properties and composition forms the original substance.

In this experiment you will observe a number of changes and will classify the change as physical or chemical based on your observations.

PRELAB

1. State the purpose of this activity in your own words.

2. List three examples of a physical change.

3. Give three observable indications that a chemical change has occurred.

GOGGLES MUST BE WORN DURING ALL PARTS OF THIS LAB.

PROCEDURE

Record your observations after each step.

1. Experiment 1

a) Attach a small candle to a glass plate. Light the candle and move it out of the way and proceed with b). Observe the glass plate at the end of the lab.

b) Obtain a test tube with wax. Heat water in a beaker on a hot plate. Immerse a test tube with wax in hot water. As soon as you see a change, remove the test tube to a rack and allow it to cool.

2. Experiment 2

a) Place 2 sugar cubes in a mortar and grind the cubes. You will use a portion of this ground sugar for each of the following experiments.

b) Place half in a small test tube and add enough water to dissolve. Shake the tube to dissolve.

c) Place the remaining sugar in a deflagrating spoon and heat over a Bunsen burner. When cool wash contents down the sink.

3. Experiment 3

a) Add a small scoop of baking soda, sodium bicarbonate, to a test tube and add water to height of about 1 centimeter. Stir.

b) Add a few drops of silver nitrate solution to the baking soda solution.

c) In another test tube place the same amount of baking soda and dissolve as above. Add hydrochloric acid. CAUTION: ACID CAN CAUSE SEVERE BURNS. WASH IMMEDIATELY IF ANY ACID COMES IN CONTACT WITH YOUR SKIN. Carefully touch the bottom of the test tube.

4. Experiment 4

Place a small scoop of copper sulfate in a test tube. Heat gently over a Bunsen burner. Refer to experiment 1b) for proper heating technique. Observe any material accumulating at the mouth of the test tube.

5. Experiment 5

a) Place about 25 mL of water in a 100 mL beaker. Add a level teaspoon (plastic spoon) of copper chloride to the beaker. Stir until the solid disappears. Measure the temperature.

b) When the solid has dissolved, place a piece of aluminum in the solution. Make sure the solution covers the aluminum. Continue to observe the mixture and measure the temperature after a minute and again after 5 minutes.

Demonstration if time permits.

6. Experiment 6

a) Mix iron and sulfur and add to a test tube. Run a magnet along the side of a test tube.

b) Heat the contents of the test tube in the fume hood. When cool run the magnet along the side of a test

tube.

CONCLUSION

1. For each experiment indicate whether the change was chemical or physical. Briefly explain each. Summarize your findings in a chart.

2. Does the formation of bubbles always indicate a chemical change? Explain.

3. Does heating a substance always cause a chemical change? Explain using your data.

4. Does burning (combustion) always indicate a chemical change? Explain.

4. CHEMICAL PROPERTIES OF FOUR LIQUIDS

The first task of a chemist is to identify substances so that one can be distinguished from another. Sometimes this is simple. If, at room conditions, substance A is a green solid, substance B a red liquid, and substance C a colorless, odorless gas, one can tell them apart by simply looking at them.Color, odor, and physical state at room conditions are examples of physical properties. Physicalproperties are those that can be tested without changing the chemical formula of the substance. Chemical properties are revealed when, for example, a solid substance is placed in water and rapidbubbling occurs, or when an iron nail is placed in an unknown liquid and a reddish substance formson it. When chemical properties are tested, substances with new chemical formulas are formed. Every substance has both physical and chemical properties.

In this experiment, you will collect data to determine if any of four liquids are the same or if all fourare different. All of the liquids have similar physical properties. They are all clear and odorless atroom temperature. You will compare their chemical properties. You will decide how to record your

data and then reason logically to determine whether any liquids are the same or whether they are alldifferent.

PRE LAB

1. State the purpose of the experiment in your own words.

2. List three chemical and five physical characteristic properties of pure substances.

3. How many characteristic properties of two substances must be alike for the two substances to be the same?

4. How many characteristic properties of two substances must be different for the two substances to be the different?

5. List three examples of properties that can be observed to distinguish between substances

6. What does the formation of bubbles in a liquid indicate?

OBJECTIVE

1. Observe visible changes.

2. Compare and contrast chemical properties of the four liquids.

3. Interpret experimental results and determine which liquids may be the same.

4. Reason logically to formulate correct conclusions.

MATERIALS

Apparatus

Reagents

24 well micro plate

blue litmus paper

Pipet with unknown

red litmus paper

Wash bottle with distilled water

universal indicator

Forceps

aluminum pellets

Laboratory apron

zinc pellets

Safety goggles

manganese (IV) oxide powder

Small straw scoop

liquids A, B, C, & D

PROCEDURES

1. Put on your laboratory apron and safety goggles.

Place 10 drops of liquid A into each of the six top wells of the 24 well microspot plate. Place 10 drops of liquid B into each of the six wells of the next row. Continue with 10 drops of liquid C in the third row, and 10 drops of liquid D in the bottom row.

2. Tear a piece of red litmus paper into four pieces and one piece in each well of column 1 of the microplate. Record your observations on your data table.

3. Repeat step 3 using blue litmus paper placed into each well of column 2. Record your observations on your data table.

4. Be sure there are no flames in the laboratory before you add one drop of universal indicator to each well of column 3. Record your observations on your data table.

5. Add one piece of zinc to each well of column 4. Wait at least two minutes and then record your observations on your data table.

6. Add one piece of aluminum to each well of column 5. Wait at least two minutes and then record your observations on your data table.

7. Add a small amount of manganese (IV) oxide to each well of column 6. Wait at least two minutes and then record your observations on your data table.

8. Obtain a bottle of an unknown liquid and add three drops to each of the six top row wells of your micro plate.

9. Repeat Procedures 3 through 8 for your unknown.

10. Using forceps remove the pieces of litmus paper from the micro plate and place them on a paper towel. Rinse and dry the forceps then remove the zinc and aluminum and place them on the paper towel also. Since the litmus paper, zinc, and aluminum are quite harmless, throw the paper towel containing them into the trash. Empty the liquids remaining in the micro plate into the sink. Rinse the micro plate with tap water by gently pouring water over the wells then turning the micro plate over to drain it into the sink. Rinse and dry the forceps.

11. Before leaving the laboratory, clean up all other materials and wash your hands thoroughly.

CONCLUSION

1. Do any liquids share the same properties? If so, explain.

2. Could any two of the liquids be the same? Explain.

3. What other chemical and/or physical properties might be used to identify each of the liquids?

4.What is the identity of your unknown? Explain in detail how you identified it.

5. DENSITY OF PENNIES

Today's penny is quite different from the penny of a decade ago. .Before 1982, pennies were made of an alloy of copper. Since then, they have been made with an outside coating of copper and an inner core of a different metal. The difference in composition of older and more recently minted pennies have resulted the pennys characteristics; including its density, or mass per unit of volume. In this experiment, you will determine and compare the densities of pennies minted before 1982 and after 1983. You will use this data to try to identify the metal used in the core of pennies minted after 1983.

PRE LAB

1. What is the purpose of this lab activity?

2. Define density.

3. What is the reason for measuring five pennies at a time rather than an individual penny?

4. How is the volume of the pennies determined?

5. Why is it important to work with dry pennies?

6. Look up the densities for the following metals:

ALUMINUM, COPPER, SILVER, ZINC

OBJECTIVE1. Make accurate measurements using a balance and graduated cylinder2. Collect data and graph3. Identify unknown4. Perform density and other calculations

MATERIALVial with 25 pre-83 pennies Vial with 25 post-83 pennies100 mL graduated cylinder Balancepaper towel

Procedure

1. Work with one set of pennies at a time; either pre-1982 pennies or post-1983 pennies. Find the mass of 5 pennies from one set. Record the mass in the appropriate Data table.

2. Add 5 more pennies to the first group and obtain the mass of these 10 pennies. Record the mass.

3. Repeat step 2, each time adding more pennies to those already on the Balance, until you have used all 25 pennies

4. Fill a 100mL graduated cylinder to the 20-mL mark with water. Be sure to use the bottom of the meniscus to measure the water level.

5. Still working with the .same set of 25 pennies; gently drop 5 of the pennies into the graduated cylinder. Record the new water level in the appropriate table.

6. Add 5 more pennies to the graduated cylinder, making a total of 10 pennies. Record the water level in the table.

7. Add 5 more pennies to the cylinder and record the water level.

8. Repeat step 7 until you have added all 25 pennies to the cylinder. Record the volume after each addition.

9. Discard the water. Dry the pennies with a paper towel and either pass them to another group to use or give them to your teacher.

10. Repeat step 1-9 using the 25 pennies in the other set of coin. Record your data in the other table.

11. Complete your data tables. Find the net volume of each group of pennies by subtracting 20 mL from the total volume recorded for each group (column 3). Enter the net volume for each group in column 4 of the data tables.

GRAPH ANALYSIS

1. Construct a graph of your results. Let the y-axis reflect the mass of the pennies. Plot the data for the pre-1982 pennies first. Then draw the best-fitting straight line (the straight line that connects as many point. a. possible). 2. On the same graph, plot the data for the pennies minted after 1983. Draw the best-fitting straight line.

CALCULATIONS

Find the slope of each line:

1. Slope: pre-1982 pennies.

2. Slope: post-1983 pennies.

CONCLUSION

1. What do the values you obtained for the slopes of the lines represent?

2. Compare the density of copper obtained for the pre-1982 pennies.

3. Calculate the percent error for the pre-1982 pennies.

4. What is the density of the post-1983 pennies?

5. Compare this value to the density of the metals listed in the pre lab.6. Which metal could be inside the post-1983 pennies?

Useful Formulas

Density = Mass (g) Volume (mL)

Slope = Y2 Y1 X2 X1

% Error = [Theoretical - Experimental] x 100 Theoretical

6. PERCENT COPPER IN A PENNY

You have determined that pennies made after 1983 contain other metals electroplated with copper to appear the same as pre-1982 pennies. If you take a metal file and score the surface of a post-1983 penny, you will note the silvery color of metal beneath the surface.

In this activity you will remove the other metal by reacting the penny with hydrochloric acid, leaving only copper shell. By carefully massing before and after the reaction with acid you will be able to determine the percent of copper in post-1983 pennies.

PRELAB

1. State the purpose of the lab in your own words.

GOGGLES MUST BE WORN IN THIS EXPERIMENT

MATERIALSOne post-1983 penny tongs

small beakerbalance

triangular file

watch glasshydrochloric acid (HCl)

acetone

PROCEDURE

1. Mass the penny.

2. Make four heavy scratches at 45 angles on the edges of the penny using the file as demonstrated.

3. Label the beaker with your name, so you can identify it tomorrow.

4. Place the penny in the beaker and carefully pour about 25 mL of hydrochloric acid into the beaker. Cover with a watch glass.

CAUTION: THIS ACID IS CONCENTRATED AND VERY CORROSIVE. AVOID CONTACT WITH SKIN AND INHALING THE FUMES!

5. Observe the reaction and record your observations. Place your beaker on the tray provided. This reaction will continue overnight.

NEXT DAY

6. Observe your beaker and some of the other beakers. Record your observations.

7. With your goggles on carefully add about 25 mL of water to the beaker to dilute any unreacted acid. Pour off (decant) as much liquid as you can, leaving the penny in the beaker. Wash the penny in the beaker with water several times.

8. Do a final rinse it with acetone.

9. Remove the penny carefully from the beaker and set it on the paper towel. Let stand for several minutes. 9. Mass the penny when dry.

CONCLUSION

1. Calculate the percent of copper in the penny. Show set up.2. Some of the pennies were floating the next day. What was the cause of this?3. What can you conclude about the effect of hydrochloric acid on copper?

7. The Law of Definite Composition

Elements are a kind of matter that cannot be decomposed by ordinary chemical means. Compounds are chemical combinations of elements. What is a chemical combination as compared to just any combination of elements? It would help to give an example of what is not a compound. The combination of oxygen and nitrogen in the air is a mixture of the gases. This mixture can be in all proportions of oxygen and nitrogen. The properties of the mixture depend upon the properties of the individual components of the mixture. Compounds, on the other hand, are special combinations of the elements. A compound has its own properties, distinct from the properties of the elements from which it was made.

The Law of Definite Composition states that the elements forming a compound always combine in the same proportion by mass. The compound water, H2O, is always a chemical combination of hydrogen and oxygen in a 1:8 ratio by mass. If a mixture of hydrogen and oxygen were reacted in some other mass ratio, for example, 1:2, water would be formed but some hydrogen would remain unreacted. Water forms only in the 1:8 ratio by mass.

In this experiment you will examine the reaction between magnesium metal, Mg, and oxygen gas, O2. When heated, magnesium reacts readily with oxygen in the air. The magnesium will be heated strongly in an open crucible for several minutes. You will measure the mass of the magnesium that reacts and the mass of magnesium oxide that is formed, and use your data to calculate the mass of the oxygen that combined. You can then find the ratio of mass of magnesium to mass of oxygen and compare your experimental ratio with the ratios of your classmates and with the actual ratio. By calculating the percent error you can then evaluate how accurately you performed the experiment and look for sources of error.

PRE LAB QUESTIONS

1. State the purpose of the experiment in your own words.

2. Why is it important to start the experiment with a clean and dry crucible?

3. What is the purpose of making sure the surface of the magnesium ribbon is clean and shiny?

4. With what element or elements does the magnesium combine when it is heated in the crucible?

5. In the procedure you are asked to reheat the crucible repeatedly until the last two masses agree to within 0.03 gram. What is the purpose of this reheating?

6. Suppose a compound of sodium and chlorine is formed in a ratio of 1.54 grams of chlorine for each 1.00 gram of sodium. How much sodium would you need to completely react with 45.0 grams of chlorine?

OBJECTIVE

1. Observe a reaction between magnesium and oxygen.

2. Calculate a ratio of mass of magnesium to mass of oxygen.

3. Measure masses carefully to obtain accurate results.

MATERIALS

Apparatus

Reagents

crucible & lid

laboratory apron and safety goggles

magnesium ribbon

crucible tongs pipe stem triangle

de-ionized water

dropper pipette electronic balance

ring stand & ringceramic tile sandpaper or steel wool

Bunsen burner & striker

FIGURE A

PROCEDURE

1. Put on your laboratory apron and safety goggles.

2. Obtain apiece of magnesium ribbon from your teacher. If the surface of the ribbon is not shiny, use a piece of sandpaper or steel wool to shine the surface.

3. Obtain a clean, dry crucible and cover. Find the combined mass of the crucible and cover and record it on the Report Page.

4. Break the magnesium ribbon into small pieces and place them into the crucible. Find and record the combined mass of the crucible, cover, and magnesium.

5. Set up the ring stand, ring, Bunsen burner, and pipe stem triangle as shown in Figure A. Place the crucible on the pipe stem triangle and begin heating the crucible gently with the lid completely on. Heat slowly by moving the flame around underneath the crucible. Remove the heat temporarily if a large amount of smoke comes out of the crucible.

6. After about four minutes of direct heating with no smoke, remove the lid slightly and heat the crucible to redness for four more minutes. Finally, remove the lid completely and heat strongly for four more minutes. (Be careful where you place the lid it is very hot!) Total of 12 minutes of heating.

7. Turn off the Bunsen burner and put the lid back on the crucible. Allow the crucible and cover to cool to a temperature low enough so that you can touch it comfortably. Minimum of 7 minutes wait time. Find the combined mass of the crucible, cover, and contents and record it on your Report Page.

8. Repeat heating of the same sample for about 5 minutes. This is the second heating. Record mass

9. Compare the masses found in steps 7 and 8. If the masses do not agree to within 0.030 gram, reheat the crucible for four minutes, cool, and find the mass again. This is the third heating. Repeat the process until you get two consecutive readings that agree to within 0.030 gram. This is known as heating to constant mass. This step may not be necessary.

10. Before leaving the laboratory, clean up all other materials and wash your hands thoroughly.

CONCLUSION

1. How would your results be affected if some of your magnesium did not react?

2. Use your textbook to help you determine the formula for the magnesium oxide that formed in this experiment.

3. Use the accepted ratio to determine the mass of magnesium that would combine with 16.0 grams of oxygen.

8. PARTICLE SIZE FROM COLLISION PROBABILITIES

Most of the information we have about the structure of the atom was derived by indirect means because the technology was not available to make direct measurements. In this activity, we are going to assume that for some reason we are not able to measure the diameter of a marble directly. We will use an indirect method to determine the size of the diameter by counting how often we succeed in hitting a marble when we shoot another marble at a group of them. The experimental arrangement is shown in the figure below.

The probability of a hit is related to a number of variables: the size of the marbles, the distance between the walls of the enclosure, the number of trials, and the number of target marbles. An equation can be derived using these variables. You will collect the necessary data and use the equation to determine the diameter of a marble. After determining the diameter by this method, you can check its success by direct measurement of the diameter of the marbles and find out how well the indirect method worked.

PRE LAB

1. State the purpose of this lab activity

2. What is probability?

3. How are the target marbles to be lined up? 4. Why will 3 meter sticks be needed? 5. What is the equation for percent error?

OBJECTIVE

1. collect data

2. use probability equation to indirectly determine marble diameter

3. directly measure marble diameter

4. calculate percent error

MATERIALS 11 marbles

tacky material

3 meter sticks

PROCEDURE

1. Obtain ten target marbles and one marble with which to bombard them. Arrange the target marbles inside a three sided enclosure made of meter sticks. The target marbles may be placed in any random position EXCEPT that there must always be room for the bombarding marble to get through between any two target marbles and no marble should be shielded from being hit. That is, each target marble must be a potential target. The target marbles will probably have to be rearranged after each hit to achieve this. See figure above.

2. Roll the bombarding marble toward the target marbles. Attempt to roll the bombarding marble along a path parallel to the walls at all times. Also, try to roll the bombarding marble randomly, that is DO NOT AIM. It may help to close your eyes.

3. Continue rolling the bombarding marble toward the target marbles, counting both the total number of rolls and the number of times a roll results in a hit. Remember that if the bombarding marble collides with any number of target marbles before hitting the wall, this is ONE hit.. You must have at least 200 rolls for good results. More than 500 do not increase the accuracy of the results. Record the number of marbles rolled and the number of hits on the Data Table. One partner should roll and the other record. You may switch rolls half way.

4. To get a direct measurement, line up your ten target marbles so that they touch each other in a straight line between two meter sticks and measure the length in centimeters to 2 decimal places.

CALCULATIONS

1. Calculate the diameter using the equation: D = H x d

2N x Tr where: Tr = number of trialsN = number of target marbles

H = number of hitsd = distance between the walls

D = diameter

2. Calculate the diameter of one marble using the direct measurement.

3. Calculate the percent error between the calculated and the measured diameter, assuming the measured diameter is the true value.

CONCLUSION

1. What are some sources of error?

2. How did Rutherford describe the atom as a result of his experiment?

3. In what ways does the situation in this experiment (which is a model of Rutherfords experiment) differ from Rutherfords experiment in which alpha particles were used to bombard a foil composed of gold atoms? (Hint: consider the charges on the subatomic particles.)

9. EMISSION SPECTROSCOPY

All atoms give off electromagnetic radiation if their gases or ions are energized by heating or by high voltage electric discharge. If the light emitted by a gas is passed through a spectroscope, a pattern of narrow lines of light is produced. Each element produces its own distinct pattern that differs from the pattern of every other element. The particular pattern of frequencies of light emitted by an atom is referred to as its emission spectrum or bright-line spectra. The emission spectrum of an element can be used as a means of identification, just as fingerprints (or DNA) can be used to identify a human being.

The unique pattern of frequencies of light emitted by an atom corresponds to the set energy given off as electrons drop from higher allowed energy states or energy levels to lower energy levels. The energy of each transition is given by Max Plancks equation,

E = hv , where E = energy in Joules, v = frequency, and h = a constant (Plancks constant). An electron can be raised from its lowest allowed energy level (ground state) to other higher allowed energy levels by absorbing certain set amounts of energy. This excited electron cannot remain at any of these higher allowed energy levels if there are unoccupied lower energy levels closer to the nucleus. The electron is attracted back to one of the lower allowed energy levels. As the electron drops back it emits a photon, a set amount of energy, in the form of electromagnetic radiation. The amount of energy that the electron emits is equal to the energy difference between the higher energy level of the excited state and the lower energy level to which the electron dropped.

PRELAB

1. State the purpose of this experiment.

2. According the modern theory of the atom, where may an atoms electrons be found?

3. How do electrons become excited?

4. What form of energy emission accompanies the return of excited electrons to ground state?

5. State two equations that are used to relate the energy content of a packet of light and its

wavelength.

6. A line spectrum is sometimes called a fingerprint of an element. What do you think is

meant by this term?

OBJECTIVE

1. Use a spectroscope

2. Observe continuous spectra

3. Observe bright line spectra from gaseous elements.

WARNING: DO NOT TOUCH POWER SUPPLIES OR TUBES.

MATERIALS

Spectroscope Tube or spectral glasses incandescent light source fluorescent light sourceHigh-voltage power supplies containing spectrum tubes of: argon, helium, hydrogen, mercury, and neon

PROCEDURE

1. Examine spectrum of incandescent and fluorescent light sources around the room. Record observations of the continuous spectra in the field provided.

2. Aim spectroscopes at the spectrum tubes set up around the room. Record your observations for each element. (Draw the specific spectral lines)

CONCLUSION

1. Compare the spectra produced by incandescent and fluorescent sources.

2. How are these spectra different from those observed in the discharge tube?

3. What causes the differences in the bright-line spectra of different elements?

4. Which element showed more lines in the red region? The blue-violet region?

5. Prior to its discovery on Earth, the existence of helium was first confirmed in the sun. Explain how this can be possible.

6. Calculate the energy of the red line of the hydrogen spectrum.

10. FLAME TESTS

When elements are heated to high temperatures they may enter an excited state, which occurs when electrons absorb energy and move to higher energy levels. When the electrons return to ground state, (the original state), they release the amount of energy that had been absorbed. This energy can be seen in the form of visible light. Each element gives off a unique set of wavelengths, which our eyes recognize as a particular color.

In this lab you will observe the colors given off by pure solutions of metal ions, and one mixture. You will then use this property of atoms to identify an unknown metal ion by comparing the color observed with the colors of known metal ions.

GOGGLES MUST BE KEPT ON DURING THE ENTIRE EXPERIMENT.

PRE LAB

1. What is the purpose of this experiment?

2. What is meant by ground state?

3. How do electrons become excited in this lab?

4. When is the energy absorbed by electrons released?

5. What is the form of this energy?

6. How should the burner flame be adjusted for best results?

7. Why is this lab done without room or outdoor lighting?

OBJECTIVE

1. observe the colors given off by a group of metal ions when heated in a flame.

2. identify an unknown metal by the color in a flame test.

MATERIALS

Goggles

splints saturated with metal ion solutions forceps or tongs Bunsen burner cobalt glass

unknown sample

PROCEDURE

1. You will be working in pairs to make observations of known metals. Each person will have his/her unknown sample to identify. NO TWO STUDENTS IN THE CLASS SHOULD HAVE THE SAME UNKNOWN SAMPLE.

2. One person from each pair will obtain wooden splints that have been soaked in solutions of each metal ion to be tested. Take two splints with sodium, two with potassium and two with the mixture. Each person will then be given an unknown sample. Immediately record your own unknown number.

3. Light the Bunsen burner. Be sure to have a good blue flame with the inner cone clearly visible. Place the end of the splint that has been soaking in the solution in the flame of the burner. Record the color of the flame.

4. Test all samples including the mixture of sodium and potassium and your unknown.

5. * Repeat the flame test with samples of potassium, sodium, and the mixture, this time, viewing the flame through the blue cobalt glass.

*Optional

CONCLUSION

1. What metal ion was in your unknown sample?

2. Explain how you identified your unknown using your data. Be specific.

3. Give two reasons why the flame test is not always valid to identify a metal.

4. What would be observed if a spectroscope were used during a flame test?

5. What color was the flame for the mixture of sodium and potassium? Explain.

6. Is it possible to use the flame tests to identify each individual metal in any mixture? Explain.

*7. What is the purpose of the cobalt glass for viewing the flame?

*optional

11. ELECTRON PROBABILITY AN ANALOGY

The Bohr model states that the electron travels in a specific orbit around the nucleus in a Planetary Model and therefore its position is space and its momentum can be readily determined. However, Werner Heisenberg in his Wave Mechanical Model showed that this is impossible since both position and momentum cannot be known at the same time. This is the famed Heisenberg Uncertainty Principle. We must therefore speck in terms of probable location of the electron in the atom.

The region of space in which an electron can be found 95% of the time is called the space orbital. The most probable distance of the electron from the nucleus is called the radius of maximum probability.

OBJECTIVE

1. use a model to determine the probable location of an electron in a space orbital.

2. calculate the region of space in which an electron can be found within the space orbital.

MATERIALS

Bulls eye target

masking tape

Ball point pen

cushioning material

PROCEDURES

1. You will be working individually.

2. Place paper as cushioning under the target, and secure to floor using masking tape.

3. Stand above target, in such a way so that your hand is 2 meters above the bulls eye.

4. Aim for the bulls eye, and drop the pen..a total of 100 times.

PRE LAB QUESTIONS

1. Why must the target be cushioned?

2. Describe Bohrs model of the atom. (Key feature of the electron position).

3. What is your prediction about the outcome of the activity? In what region will the electron most likely be located?

4. What is the purpose of this lab activity?

CALCULATIONS

1. Location the 95 dots closest to the bulls-eye. Draw smooth circle around the pen dots to represent the space orbitals.

2. For each circle preprinted on the target, count the pen dots, and record.

3. Graph the number of dots in a region vs. average radius. Draw a smooth curve.

4. Divide the total number dots in each circular region, by the area of that region according to the values given on the data table. (This is the number of dots per square centimeter). Record these values on the data table.

5. Create another graph; plot the dots/cm2 value vs. average radius.

CONCLUSION QUESTIONS

1. When you through a dart at a target, can you predict precisely where it will strike?

2. The s (spherical) orbital is non directional. Does your orbital appear to be this way? Explain.

3. Interpreting the graph: what is the area of maximum probability (of electron location).

4. Make certain to attach your target to your lab notebook before submission.

12. MENDELEEV FOR A DAY

As more and more elements were discovered during the 1800s it became important to categorize them according to similarities in chemical and physical properties. A Russian chemist, Dmitri Mendeleev (1834-1907) was the first to do so successfully. He arranged the elements in vertical columns in order of increasing atomic mass. The columns were then arranged so that elements with similar chemical properties were placed side by side.

Mendeleev left numerous spaces in his table because there were no known elements with the appropriate properties to fill the spaces. He then predicted the properties of these unknown elements based on the properties of the elements next to them on his periodic table. When these missing elements were discovered, they were found to have properties very similar to those he predicted.

As a model of Mendeleevs work, in this investigation you will group unknown compounds (instead of elements) according to their chemical behaviors. You will see if a precipitate forms when two solutions are missed together. You then will observe which precipitates are dissolved by another solution. Finally you will record any color changes that occur when two solutions are mixed together. After analyzing your data, you will place each unknown solution into a group with other solutions of similar characteristics.

OBJECTIVE

To model Mendeleevs ideas

To group nine unknown compounds based on their chemical behaviors.

PRELAB

1. How does Mendeleevs periodic table differ from the modern periodic table?

2. Why did Mendeleev leave blank spaces on his periodic table?

3. What is the reason (unknown to Mendeleev) that elements in the same group have similar properties?

4. Why is it necessary to rinse the stirring rod between test tubes?

MATERIALS:

3 test tubes labeled A, B, C

Test tube rack

10-mL graduate cylinder

Stirring rod

Unknown solutions 1-9

4 dropper pipets containing test solutions A, B, C & D

PROCEDURE:

GOGGLES AND APRONS ARE NEEDED FOR THIS LAB. CAUTION SOLUTION D IS VERY CORROSIVE. WASH YOUR HANDS WITH SOAP AND WATER IMMEDIATELY IF ANY SOLUTIONS COME IN CONTACT WITH YOUR SKIN.

1. Each group will work with one of the unknown solutions. These unknown solutions are identified by numbers 1-9. The data will then be shared with the class at the end of the experiment.

2. Put on goggles and aprons.

3. Label three test tubes A, B, C.

4. Obtain one unknown solution. Note the number. Place 1 mL of the unknown solution in each of the three labeled test tubes.

5. To test tube labeled A, add 12 drops of test solution A.

To test tube labeled B, add 12 drops of test solution B.

To test tube labeled C, add 12 drops of test solution C.

6. Any test tube that does not show an immediate change should be stirred for about 10 seconds. Make sure you rinse the stirring rod after each use to avoid contaminating the next solution. Record the observations on the Data Table. Be sure to record in the space for your unknown sample.

7. To any test tube that contains a precipitate, add 20 drops of test solution D and stir for at least 15 seconds. Again rinse the stirring rod after each use. Record the results.

8. Dispose of all solutions in the waste container provided, then rinse out the test tubes and graduated cylinder in the sink.

9. Clean up and wash your hands. Leave materials out on the bench.

CONCLUSION QUESTIONS

1. Why do you think this investigation is titled Mendeleev for a Day?

2. Based on your observations, group the unknown solutions into Families according to similarities in chemical behavior. Arrange your groups in a chart.

3. Justify your arrangements by referring to your data.

4. Some members of the same family that show similar but not identical reactions. Give an example of this.

5. No members of Group 8A (18) of the modern periodic table can be found on Mendeleevs version of the periodic table. Suggest an explanation for their absence.

13. PERIODIC TABLE I:

A STUDY OF REACTIVITY OF METALS

OBJECTIVE

1. Compare reactivity of metals in two Groups and in a Period by observing reactions.

2. Identify an unknown Group II metal in a compound.3. Determine reactivity trends in families and in periods.

PRE LAB

1. What is the purpose of this lab?

Read the textbook on reactivity of metals and the procedure to answer the following:

2. What is the trend in activity in a Group as the atomic number increases?

3. What is the trend across a Period as atomic number increases?

GOGGLES AND APRONS MUST BE WORN FOR THESE EXPERIMENTS.

PART I

MATERIALS

test tubes, test tube rack, calcium piece, magnesium ribbon, aluminum pellet, phenolphthalein solution, splint, match, forceps, steel wool, Bunsen burner, test tube holder

PROCEDURE

1. The reactivity of Alkali metals will be observed by demonstration.

2. Pour about 5 mL of distilled water into a clean, dry test tube and place it in the

test tube rack. Using the forceps, add a piece of calcium to the water. DO NOT TOUCH THE CALCIUM WITH YOUR HANDS. IT IS CORROSIVE TO SKIN. Observe the reaction. Collect the gas being released by holding an inverted dry test tube over the reactant tube.

3. Test for hydrogen gas by inserting a burning splint into the mouth of the upper test tube.

4. Add a drop of phenolphthalein solution to the reactant tube. Record your observations.

5. Clean the surface of the magnesium ribbon with steel wool. Break it into small pieces and place the pieces in a test tube. Repeat the above procedure.

6. If there is no visible reaction, gently heat the water in the test tube just to boiling. BE SURE TO POINT THE TUBE AWAY FROM YOURSELF AND OTHERS WHILE HEATING.

7. Once it is boiling, turn off the burner, return the test tube to the rack and collect the gas. After a few seconds, test for hydrogen as above. Add phenolphthalein. Note any color change in the test tube.

8. Repeat the procedure with one aluminum pellet.

PART II

The more active a metal, the more reactions will be observed. Formation of a precipitate will indicate that a reaction has occurred.

SALTS OF BARIUM AND STRONTIUM ARE EXTREMELY TOXIC. AVOID CONTACT WITH THESE CHEMICALS AND WASH YOUR HANDS THOROUGHLY AFTER USE.

MATERIALS

spot plate, dropper pipets containing solutions of Mg(NO3)2, Ca(NO3)2, Sr(NO3)2, Ba(NO3)2, H2SO4, Na2CO3, Na2CrO4.

PROCEDURE

1. To each well of a spot plate place about 10 drops of one of the following solutions containing alkaline earth metals: Mg(NO3)2, Ca(NO3)2, Sr(NO3)2, Ba(NO3)2. To each solution add two drops of H2SO4. Record whether a precipitate appears, the relative amount and color.

If no precipitate is formed leave the box blank.

2. Repeat the procedure but add a few drops Na2CO3(aq) to each solution.

3. Repeat the procedure again but add Na2CrO4(aq) to each solution.

4. Obtain an unknown solution. The solution will contain ions of one of the alkaline earth elements: Mg2+, Ca2+, Sr2+, or Ba2+. Test with the solutions used above (steps 2 3) in order to identify the unknown ion.

CONCLUSION

1. Did this experiment verify the predicted reactivity trend of Group 1A and 2A elements? Explain using your observations.

2. Predict what you would have observed if the following elements had been tested:

Beryllium, Strontium, Francium. Explain.

3. You observed three elements in period 3 in this lab. Do your observations support the predicted reactivity trend? Describe.

4. If zinc and iron had been tested, how would their reactivity compare to the metals in the same PERIOD that you observed in this lab?

5. Describe any relationship that you can determine between the number of precipitates formed by each compound and the location of the alkaline earth metal on the periodic table.

6. What is the identity of your unknown compound? Support your conclusion by referring to your data.

14. IONIC AND MOLECULAR COMPOUNDS: COMPARING PROPERTIES

Compounds can be classified by the types of bonds that hold their atoms together. Ions are held together by ionic bonds in ionic compounds; atoms are held together by covalent bonds in molecular compounds. You cannot tell whether a compound is ionic or molecular simply by looking at a sample because both types can look similar, when they are solids. In this activity some simple tests will be done to classify compounds by type because each type has a set of characteristic properties shared by most members. Ionic compounds are usually hard, water-soluble, have high melting points and can conduct electricity when dissolved in water. Molecular compounds can be soft or hard, are usually less water-soluble, tend to have lower melting points, and cannot conduct electricity when dissolved in water. In addition, ionic compounds are always solids at room temperature, while molecular compounds can be solids, liquids or gases.

OBJECTIVE

1. observe some characteristics of six different solid substances 2. classify the solids as ionic or molecular

MATERIAL

Hot plate

glass slides or watch glasses

7 samples in vialsspot plate

conduction apparatus with battery

PROCEDURE

1. Obtain seven solid samples vials.2. Using a clean scoopula or wood splint for each sample, and place several grains on a glass surface to observe melting. Keep on hot surface no more than 3 minutes. (VAPOR HAZARD)Observe which samples melt.

3. Place several grains of each sample into their own spot plate well. Add de-ionized water. Observe which samples dissolve.

4. Using the solutions you made in step 3, and place the conduction apparatus electrodes in each well. Clean apparatus electrodes with de-ionized water before each testing

Observe which mixtures cause the light to glow or flash the fastest. Compare results with de-ionized or distilled water, used as a control

PRE LAB

1. What is the purpose of this lab?

2. Describe some characteristics of ionic compounds.3. Describe some characteristics of molecular compound.

CONCLUSION

1. Complete the statements:

a) The following substances ______are ionic because ______

b) The following substances ______are molecular because _____

2. If you know the formula of the compound can you predict whether it is ionic or molecular? Explain.

3. Predict the following, based on the patterns established in this experiment:a) Solubility of sodium iodide in water(high/low)

b) Relative melting point of benzoic acid (C6H5COOH ) (high/low)

c) Electrical conductivity of glucose in water

d) Electrical conductivity of magnesium chloride in water

15. MODELS OF COVALENT COMPOUNDS

Why should people care about the shapes of molecules? Consider that the properties of molecules depend not only on their molecular composition and structure, but on their shape as well. Molecular shape determines a compound's boiling point, freezing point and the nature of its reactions.

The geometry (shape) of a small molecule can be predicted by examining the central atom and identifying the number of atoms bonded to it and the number of unshared electron pairs surrounding it. The names of the shapes you will be able to identify are: linear, bent, trigonal pyramidal, tetrahedral, and trigonal planar.

Covalent bonds are formed when electrons are shared by two atoms. If the two atoms are alike, that is have similar electronegativity values, the bond is said to be nonpolar covalent. If the atoms are not alike, that is there is a large difference between their electronegativity values, the bond is polar covalent. More than one pair of electrons can be shared. This results in a double or triple bonds.

Molecules can also be polar or nonpolar. If all the covalent bonds are nonpolar, the molecule will be nonpolar. If the covalent bonds are polar, the molecule can still be nonpolar if the polar bonds are symmetrically arranged around a central atom, so that their charges cancel each other out. On the other hand, if the arrangement of the polar bonds is asymmetrical, the electrons will be attracted more to one end of the molecule and a polar molecule or dipole will result. Polarity of the molecule depends on the bonds and the shape.A model in chemistry is a way of thinking about the structure of matter. In this laboratory, you will build molecular models to show the three-dimensional nature of matter, identify the shape, and associate the electron dot diagram with the shapes.

To give additional illustrations, this lab will also introduce you to organic compounds. These substances contain carbon chains. (examples: C2H2, C2H4, C2H6 )

PRELAB

1. State the purpose of this lab activity

2. What properties of compounds are determined by the shape of the molecule?

3. What shapes can molecules have?

4. How can you determine if BOND is polar or nonpolar?

5. Predict the bond type (ionic, polar covalent, nonpolar covalent) for the following. Show the electronegativities differences for each pair.

a. Na and Cl____________________________________

b. C and H______________________________________

c. S and O _____________________________________

d. N and N_____________________________________

6. What factors determine if a MOLECULE is polar or nonpolar?

OBJECTIVE

1. build molecular models to show the three-dimensional nature of matter

2. observe symmetrical and asymmetrical molecules

3. identify molecular shapes, and associate them to electron dot diagrams

4. examine several organic compound structures

5. determine covalent bonding type, and molecule type

MATERIALS

Molecular models kits

model color coded key

PROCEDURE

1. Assemble models for all formulas in the data table.

2. Complete the Data Table.

CONCLUSION

1. Which shapes always produce polar molecules?

2. List the NONPOLAR MOLECULES which have POLAR BONDS.

3. Both water and carbon dioxide are molecules composed of three atoms and 2 bonding clouds. One is polar and the other is nonpolar. Explain why.

4. Why is CH3Cl polar, while CCl4 is not?

5. The polarity of a substance can have a great effect on its solubility. A rule of thumb for solubility is like dissolves like. Knowing this general rule, what can you predict about the polarity of alcohol if you know that alcohol dissolves in water?

6. Classify each of the compounds using one of the following:

(Refer to the electronegativity chart to determine bond type.)

ionic bonding

polar covalent bonds in polar molecules

polar covalent bonds in nonpolar molecules

nonpolar covalent bonds in nonpolar molecules.

a) I2

b) CBr4

c) H2S

d) NaF

16. CHEMICAL NAMES AND FORMULAS

Chemical substances are described not only by unique names but also by unique chemical formulas. We use this language to communicate about chemistry. In this lab activity you will combine certain ions, and produce new compounds. This type of formation occurs when a cation is able to combine with an anion. The formation of these new compounds will be visible to the unaided eye. These specific co will then be named and their formulas written. Some of these ionic compounds will need roman numerals in their names. You will need to refer to your textbook, reference charts and class notes for additional assistance. SAFETY: goggles and aprons must be worn at all times

PRE LAB

1. What is the purpose of this lab activity?2. What is a precipitate?3. When is a roman numeral used in a name? 4. Which cations require the use of roman numerals?5. What is a cation? List the cations in this experiment.6. What is an anion? List the anions in this lab activity.

OBJECTIVE1. write formulas for ionic compounds3. observe precipitation of these compounds2. write names for ionic compounds

4. identify cations and anions

MATERIALS 9 solutions in dropper pipettes

spot plate or plastic reaction surface dionized water

goggles and aprons

PROCEDURE

PART I: 1. Obtain a set of vials for each lab table. In this activity you may work in 3-4 person groups. Make observations and write names and /or formulas on data table # 2.

2. After your group is done you may rotate to another table.

PART II: 1. Put on goggles and apron. 2. Clean spot plate or plastic reaction surface thoroughly, and rinse with dionized water. 3. Collect solutions from indicated area. 4. Add three drops of each indicated solutions into the indicated spot. 5. Record observations in the numbered data table #1 boxes using the following symbols: ppt = precipitate formation (cloudy or grainy appearance)

6. Follow instructions for safe disposal of solutions from your spot plate or reaction surface. 7. Clean up your lab area thoroughly and return all materials and equipment to their original location. 8. Remove and put away your goggles and aprons

CONCLUSION

1. In each box in table # 2, write the name and formula of the precipitate formed. **Reaction #1 has been done for you. Reminder: Some names will require Roman Numerals.

2. Write the formulas for the following compounds: lead (II) chloride, lead (II) chlorate, zinc phosphate, zinc phosphide

3. Using your answers in question #2, explain how you distinguish between the binary

ionic compounds and ionic compounds with polyatomic ions

17. COMPOSITION OF HYDRATES

Hydrates are ionic compounds (salts) that have a definite amount of water (water of hydration) as part of their structure. The water is chemically combined with the salt in a definite ratio. Ratios vary in different hydrates, but are specific for any given hydrate. The formula of a hydrate is represented in a special manner. The hydrate of Cobalt (II) chloride has the formula CoCl2 . xH2O. The unit formula for the salt appears first, and the water formula is last. The dot means that water is loosely bonded to the salt. The coefficient x stands for the number of molecules of water bonded to one unit of salt. This special formula illustrates the law of definite composition.

When hydrates are heated, the "water of hydration" is released as vapor. The remaining solid is known as the anhydrous salt. The general reaction for heating a hydrate is

hydrate ( anhydrous salt + water

The percent of water in a hydrate can be found experimentally by accurately determining the mass of the hydrate and the mass of the anhydrous salt. The difference in mass is due to the water lost by the hydrate. The percentage of water in the original hydrate can easily by calculated.

GOGGLES AND APRONS MUST BE WORN. BE CAUTIOUS IN HANDLING HOT GLASSWARE.

PRELAB

1. What is the purpose of this lab activity?

2. Calculate the theoretical percent of water in the following hydrates. (HINT: One of these will be your unknown!)

MgSO4 . 7 H2O

CuSO4 . 5 H2O

BaCl2 . 2 H2O

Na2SO4 . 10 H2O

CaCl2 . 2 H2O

OBJECTIVE

1. Determine the % of water in an unknown hydrate 2. Identify an unknown hydrate sample from a given list of hydrates

MATERIALS

Evaporating dish

scoopula

balance, ring stand crucible tongs or mitteniron ring

wire gauze burner

vial containing unknown hydrate sample

PROCEDURE

1. YOU ARE WORKING INDIVIDUALLY. Set on ring stand, ring with wire gauze. Wash and dry an evaporating dish then heat it in the hottest part of the flame for about one minute. Use tongs/or mitten to handle dish. First allow dish it to cool thoroughly. Mass the evaporating dish.

2. Obtain a sample of unknown hydrate. Be sure to record the number on the vial. Mass about 2 grams of the hydrate into an evaporating dish. Record the masses accurately. Do not waste time trying to get exactly 2 grams. Break up any lumps.

3. Adjust Bunsen burned so there is a double blue cone. Set ring on stand, about 8 -10 cm from the barrel.

4. Heat dish gently by moving the burner flame back and forth along the bottom, for 5 minutes. Increase the heat gradually and set burner down on stand. Avoid any popping and splattering. 5. Heat strongly for an additional 5 minutes. If the edges of the hydrate start to turn brown, remove the heat momentarily and resume heating at a gentler rate.

6. Remove the dish and allow it to cool for at least 5 minutes. Find the mass as soon as it is cool. Massing dish while warm will cause experimental error.

7. Repeat heating (steps 4 and 5 to obtain the second heating value. Cool and mass to make sure all the water has been removed. If the mass changes by 0.1g or more, heat a third time. Repeat until there is essentially no change in the mass. You can then assume that all the water has been driven off.

CONCLUSION

1. Write the number and complete formula of your unknown hydrate? Why did you select it from the list? Use your calculations to support your choice.

2. Why do you think it is necessary to measure the mass of the anhydrous salt immediately after cooling?

3. A hydrate compound has a mass of 1.632g before heating and 1.008g after heating. Compute the experimental percentage of water in the hydrate.

18. ALUMINUM FOIL

This activity will be done cooperatively. All members of the group must be involved and one grade will be given to the group. (If however, I observe that a member of the group is not participating, that person will receive a lower grade.)

OBJECTIVE:

To determine the thickness of a piece of aluminum foil to three significant digits.

To determine the thickness in atoms.

To determine the number of atoms of aluminum in the piece of foil.

To answer the question stated below (at the end.)

SOME DIRECTIONS:

1. Write the names of the group members.

2. You may use any equipment that is presently in the room.

3. Decide on a procedure and write it.

4. Prepare a data table.

5. Show calculations clearly.

SOME THINGS THAT YOU ARE NOT PERMITTED TO DO:

1. You may not destroy, crumble, tear or fold your piece of foil. It must be returned in exactly the same condition that you received it.

2. You can only confer with members of your group. You are not permitted to spy or eavesdrop on other groups.

3. You cannot remove any papers from this lab. All materials must be turned in by the end of the period.

SOME INFORMATION THAT MAY BE HELPFUL:

1. The density of aluminum is 2.69 g/cm3.

2. The diameter of one atom is 2.50 x 10-8 cm. (Assume the atom is a sphere.)

WHAT IS TO BE SUBMITTED BY THE END OF THE PERIOD

1. The names of the group members.

2. The aluminum foil

3. The procedure and data table.

4. The calculations with the results of the objectives clearly marked.

5. The answer to the following questions with calculations shown:

If the population of the world is about 5.6 x 109 people, how many atoms of aluminum from your foil could you distribute to each person in the world?

19. EMPIRICAL FORMULAS

You will be given an unknown binary compound to analyze. The general formula of each compound will be AxBy. Heating any of the compounds will cause them to decompose according the following equation: AxBy ( xA( s)+ yB(g)

Since B" is released as a gas, strong heating will leave only the" A" of the unknown in the evaporating dish. GOGGLES AND APRON MUST BE WORN

PRE LAB

Show all work, and circle final answer:

1. What is the purpose of this lab?

2. A 0.750 g sample of tin is oxidized with nitric acid to form tin oxide. Calculate the empirical formula of tin oxide if the original tin sample gained 0.201 g of oxygen.

3. Excess sulfur reacts with 0.565 g of cobalt to give 1.027 g of cobalt sulfide. Find the empirical formula of the product.

4. If 1.164 g of iron filings reacts with chlorine gas to give 3.384 g of iron chloride, what is the empirical formula of the compound?5. Why should you wait at least 5 minutes before massing the evaporating dish?

Precaution: THE SOLIDS ARE SAFE IF HANDLED PROPERLY. IF ANY SOLID COMES IN CONTACT WITH YOUR SKIN, WASH WITH SOAP AND WATER.

Cleanup: WASH RESIDUE IN THE EVAPORATING DISH DOWN THE DRAIN WITH PLENTY OF WATER. RETURN VIAL.

OBJECTIVE1. analyze a binary compound 2. determine formula of the unknown

MATERIALevaporating dish

wire screen

balancetongs or mitten Bunsen burneriron ring with stand

striker

PROCEDURE1. You will be working individually. Obtain a sample and record the unknown number.

2. Clean an evaporating dish with water. Dry the dish by placing the evaporating dish on a wire screen and iron ring on a ring stand over a laboratory burner and heat for several minutes.

3. Carefully remove the dish with tongs and allow it to cool on a tile until you no longer can feel heat radiating from it (min. 5 minutes).

4. When the dish is cool (min. 5 minutes), measure the mass of the dish to the nearest 0.01 g. Record the mass. HOT DISHES SHOULD NOT BE PLACED ON THE BALANCE.

5. Add about 3 grams of the unknown to the evaporating dish and measure the mass to the nearest 0.01 g. Record mass.

6. Begin heating slowly. (The flame should be a double blue cone, but keep farther from the stand). Increase the heat until you have heated the dish strongly for about 10 minutes.

You are driving off all of the "B" in your unknown in this step.

7. Remove the dish form the ring stand; let it cool on the tile. Measure the mass of the dish and contents (now just the "A" in your unknown). Record the mass.

8. Reheat with a hot flame for a couple of minutes, cool on the tile and measure the mass again.

If the mass has changed (in the 0.) place) heat again and mass until there is no change. These steps confirm that all the "B" has been driven off.

CONCLUSION

1. What is the number and empirical formula of your compound?

2. What is an empirical formula?3. What additional information would you need to calculate the molecular formula?

THE ATOMIC MASSES OF "A" AND B" CAN DETERMINE FROM THIS TABLE

Unknown Number

Atomic Mass of "A"

Atomic Mass of "B"

1

106

20.7

2

35.3

62.0

3

89.6

35.0

4

46.6

27.3

5

68.9

13.5

6

30.5

71.3

7

122

35.7

8

46.1

53.9

9

23.0

40.3

10

92.2

27.0

11

47.7

41.9

12

78.5'

11.5

13

34.1

39.9

14

63.3

24.8

15

212

41.4

16

68.2

79.8

17

70.6

124

18

61.0

142.6

19

46.0

80.6

20

92.2

107.8

21

106

20.7

22

35.3

62.0

23

89.6

35.0

24

46.6

27.3

20. SINGLE REPLACEMENT REACTIONS

(Activity Series)

In a single replacement reaction one element replaces another element in a compound as indicated by the general equations:

A + BX AX + B or Y + BX BY + X

In the first, A replaces B and B is liberated. In the second, Y replaces X and X is liberated. In single replacement reactions, an element reacts with a compound, displacing an element from that compound. An example of the first type of single replacement is the reaction of zinc with hydrochloric acid in which zinc replaces hydrogen, liberating hydrogen gas: Zn + 2 HCl ZnCl2 + H2. An example of the second case is the replacement of bromine in potassium bromide by chlorine: Cl2 + 2 KBr 2 KCl + Br2.

Most single replacement reactions occur in aqueous solutions.Metals can be organized according to the ease with which they undergo certain chemical reactions (generally single replacement reactions). These Tables are called activity series, which list elements in order of their ability to replace other elements. The most active element, which is placed at the top of the series, can replace every element below it.

In this experiment you will determine the order of activity of four metals: iron, copper, zinc and magnesium by studying the single replacement reactions that you perform.

PRE LAB

1. What is the purpose of this lab?

2. Why must the spot plate be cleaned after each trial?3. During a single replacement reaction what happens to a metal that is least reactive?

OBJECTIVE

1. perform single replacement reactions2. study single replacement reactions3. interpret observations4. determine the order of activity of four metals

MATERIALS Spot plate

6 solutions in dropper pipets Dionized water 4 types of metals in vials (Pb, Cu, Zn, Mg)

PROCEDURE

1. Clean spot plate wells. Do a final rinse with dionized water.

2. Pour 5 drops of Cu(NO3)2 solution into well 1, 5 drops of Pb(NO3)2 solution into well 2, 10 drops of Zn(NO3)2 solution into well 3, 5 drops of AgNO3 solution into well 4, 5 drops of HCl into well 5, and 5 drops of Mg(NO3)2 into well 6.

3. To each well add a clean piece of Pb.

4. Note and record the results.

5. Clean spot plate. Dispose of metal into solid waste can.

6. Repeat steps 1 4, three more times. (Using Cu, Zn, and Mg instead of Pb).

CONCLUSION

1. Write balanced equations for each reaction that occurred.2. Based on your observations, list the order of decreasing activity. (Most active first). Justify your answer.

21. DOUBLE REPLACEMENT REACTIONS

Precipitation occurs in solution when two chemicals join together to form a product that is insoluble in water and falls out of solution like rain or snow. A precipitate is a solid substance that separates from solution during a chemical reaction, and can be identified by the cloudy, milky, gelatinous or grainy appearance it gives to the mixture. In a test tube the, the solid might settle to the bottom of the container. The reactions are usually double replacement reactions.

In this laboratory activity you will mix solutions of lead, silver, and calcium compounds with other compounds in solution. You will observe and describe the precipitates that are formed. You will then write and balance complete chemical equations to describe precipitation reactions.

GOGGLES MUST BE WORN. WASH YOUR HANDS AFTER CLEANING UP.

PRE LAB

1. State the purpose of the experiment in your own words

2. What are cations? Give two examples.3. What are anions? Give two examples4. Where are anions and cations found on the periodic table?5. What is a solution? What is a precipitate?

OBJECTIVE

1. observe precipitation formation

3. write balanced double replacement reactions2. describe precipitation formation

4. identify the precipitate in each reaction that occurs

MATERIALS

11 solutions in pipettes

plastic reaction surfacedionized water

PROCEDURE

1. Place lab table in acetate sheet. Make certain it is clean by rinsing with dionized water. Dry with paper towel.

,2. Place one drop of each solution as shown in lab table. (Combine solutions as shown in the table). 3. Record observations on data table. Write ppt if a precipitate forms. . Do not let the tip of the pipette touch the drop to avoid contamination and false reactions.

3. Wash chemicals down the sink. Flush with water and wash the plastic.

CONCLUSION

1. How do you know a double replacement reaction occurs?

2. What two CATIONS commonly form precipitates?

3. Which of the mixtures give no visible reaction?

4. Write balanced chemical equations for all the precipitation reactions of AgNO3 that you observed. Be sure to combine ions in formulas according to their charges. Mark the precipitate with an (s).

5. Write balanced chemical equations for all the precipitation reactions of CaCl2 that you observed.

22. FOUR SOLUTION PROBLEM

You are provide with 8 pipets containing aqueous solutions. Four are identified and labeled AgNO3, FeCl3, KSCN and NaOH. The other four pipets contain the same solutions but labeled only A, B, C and D. Note: SCN- is a polyatomic ion called the thiocyanide ion. You are expected to identify what solution each pipet contains. You will use your observations of double replacement reactions as a tool to help you solve this problem.

OBJECTIVE

Identify the contents of pipets A, B, C and D.

MATERIALS

AgNO3, FeCl3, KSCN and NaOH in labeled pipets.

AgNO3, FeCl3, KSCN and NaOH in pipets labeled A, B, C and D.

Plastic Sheet Protector (reaction surface).

Distilled water bottle.

Cup (to hold pipets).

SAFETY PRECAUTIONS

Wear safety goggles and aprons.

Wash hands after the lab.

AgNO3 will stain skin and clothing.

PROCEDURE

1. React each of the known solution with each other. Record your observations for each reaction in Data Table 1. If a precipitate formed, use the solubility chart to predict which compound was the precipitate and its color and record the formula and color of the precipitate in the Table 1. Use colored pencils to indicate the color.

2. Once you have reacted all known reactants, react each unknown with each known. Record you observations in Data Table 2. Observe the colors of the precipitates that formed in order to determine the identity of the unknown solutions. Use colored pencils to indicate the color.

CONCLUSION

1. Write the chemical and net ionic equation for each reaction in which a precipitate was formed from Table 1.

2. What is the identity of the unknown pipets?

23. TYPES OF CHEMICAL REACTIONS

There are five basic reaction types that we can observe in this course: Single replacement, double replacement, decomposition, synthesis, combustion (complete or incomplete). In this lab activity your will carefully perform each of the reactions, making careful observations. Based on class discussion, other lab activities, demonstrations, your textbook and class notes, you will determine the reaction types for parts A F and write balance equations.

Goggles and Aprons must be worn throughout this lab.

PRE LAB

1. What is the purpose of this lab?

2. Write balanced chemical equations to describe the following chemical reactions:

a) Aluminum reacts with the oxygen in the air to form aluminum oxide.

b) Hydrogen peroxide, H2O2, decomposes into water and oxygen gas.

c) Hydrochloric acid reacts with magnesium to produce hydrogen gas and magnesium chloride. . d) Hydrochloric acid also reacts with sodium hydroxide to produce table salt and water.

3. Now, identify each type of reaction.

OBJECTIVE1. observe different reaction types

3. identify reaction types2. write word equations for each reaction4. write balance equations for each reaction.

MATERIALS

right-angle glass bend

large test tubes (3)

splintsburner, large beaker

small beaker

forcepssmall test tubes (2)

solid stoppers

test tube rackring stand

one-hole stopper

rubber tubing

test tube holder

PROCEDURE

REACTION A

1. Place the CuCO3 in a small test tube to a height of about 1 cm.

2. Note the appearance of the sample.

3. Using the test tube holder heat the tube strongly for about 3 minutes. Extinguish the flame and then hold a burning splint into the test tube. Observe the result and note any changes in the appearance of the residue in the test tube.

REACTION B

1. Obtain a piece of magnesium ribbon. Polish with steel wool.

2. Using crucible tongs ignite the magnesium in the Bunsen burner and hold it over a watch glass.

DO NOT LOOK DIRECTLY AT THE BURNING MAGNESIUM!

3. Examine the material in the watch glass.

4. Wash the contents of the watch glass down the sink.

REACTION C

1. In the small test tube mix a few drops of AgNO3 and HCl. Record the results. 2. Dispose of liquids in the hood

REACTION D (See fig. 1)

1. Place 10 ml of hydrochloric acid in one test tube. Insert the one- hole stopper with the glass tube into the test tube.

2. Clamp on a ring stand.

3. Fill a test tube with tap water, and invert the tube in a large beaker of tap water as shown in figure 2. Keep the mouth under the water.

4. Run the rubber tubing to the collection test tube so that the free end of the test tube is just inside the mouth of the tube.

5. Obtain some pieces of mossy zinc. Open the test tube containing the HCI and carefully drop in the zinc. Record your observation.

6. Allow the collection tube to fill with gas. Collect another if necessary.7. Stopper the tubes of gas with solid stoppers and remove from the water. Keep them inverted. fig. 1 Zinc + HCI

REACTION E

1. Dry the tubes on the out side. Remove the stopper from one of the test tubes and carefully bring a burning splint to the mouth of the gas-filled tube. Notice any change in tube.

2. Record observation.

3. Carefully dispose of the acid in the beaker labeled acid in the hood. BE SURE TO KEEP GOGGLES ON DURING CLEANUP.

CONCLUSION

1. Study the observations you recorded and then identify the type of reaction that took place in each case (A-E).

3. Write balanced equations for each reaction.

24. A CHEMICAL REACTION: MOLES OF IRON AND COPPER

PRE LAB

1. What is the purpose of this lab activity?2. What are the two possible formulas for iron chloride?3. Write the two balanced equations that could occur in this lab when iron reacts copper II chloride. (In one assume FeCl2 is formed and in the other FeCl3).

4. What does it mean to decant in the context of the lab activity?5. Why must the product of this reaction be completely dry before massing?

OBJECTIVE

1. determine the number of moles of copper produced and the number of moles of iron used in the reaction.

2. calculate the ratio of moles of iron to moles of copper.

3. determine the formula and the name of the iron chloride produced.

MATERIALS

100 Ml beaker

250 Ml beaker

graduated cylinderstirring rod

wash bottle w/de-ionized water

forceps

balance

steel wool

copper(II) chloridedrying oven or heat lampiron nail

1.0M HCl solution

PROCEDURE

1. Weigh the 100 Ml beaker.

2. Add about 2.50 g of copper chloride to the beaker. Add 15 Ml of de-ionized water and stir until all the copper chloride dissolves.

3. Use the steel wool to make the nail shiny (if not new) and weigh the nail. Record. Place the nail in the beaker containing the solution. Leave it for about 20 minutes.

4. Use tongs to pick up the nail. Any copper that is adhering to the nail should be added to the beaker by scraping and washing it off with water in the wash bottle. Set the nail aside to dry on a paper towel.

5. Carefully decant* the liquid from the copper. Pour the liquid into the large beaker so if some the copper is poured, off you can retrieve it. Discard the liquid in the sink.

6. Rinse the copper again with 15 Ml de-ionized water. Decant and repeat this step three more times.

7. Wash the copper with 10 Ml 1.0M HCl, decant and wash one more time with the water.

8. Label the beaker and place under drying lamp or in drying oven. Dry.

* See diagram on the next page.

It may be necessary to wait until the next day. 9. Weigh the Nail. Record.

10. Weigh the beaker with the dry copper. Record. At this point the beaker with the Cu must dry completely.

11. Clean out the copper into the waste basket. Rinse the beaker and return to the side of the room.

To Decant

Clean off Nail

CALCULATIONS: Show all set-ups on the table. Make certain to use units.

1. Calculate the mass of the iron that reacted. (nail before reaction nail after reaction)

2. Calculate the moles of iron that reacted.

3. Calculate the mass of copper that formed. (beaker with Cu beaker)

4. Calculate the moles of copper that formed.

5. How many moles of Fe reacted and how many moles of Cu were formed in your lab? Is the mole ratio of iron to copper closer to 1:1 or 2:3?

6. Use the ratio of Fe to Cu you calculated to determine which equation best describes the reaction that occurred in this lab. (Refer to prelab question #3.)

CONCLUSION

1. What type of reaction is this?

2. Can a reaction occur with copper nails and iron chloride? Explain.

25. MOLE - MASS RELATIONSHIP & %YIELD

In a balanced chemical equation, all reactants and products must be represented by symbols or formulas. The total number of atoms of each element must be the same on each side of the equation to satisfy the law of conservation of mass.

A calculation of the formula mass of a reactant or product enables a researcher to convert from grams of a particular substance, to moles of that substance. The mole relationship, given by coefficients of the balanced equations, then allows the researcher to calculate how many moles of every substance will take part in the reaction.

In this experiment, you will investigate the qualitative relationships in the reaction:

NaHCO3 (s) + HCl (aq) NaCl (aq) + CO2 (g) + H2O (g)

A known mass of sodium hydrogen carbonate will be reacted with excess hydrochloric acid. Knowing the mass of NaHCO3(s) that reacts, you can determine from the balanced equation the mass of NaCl that should be produced. You can compare this theoretical value with the actual experimental mass of NaCl produced.

PRELAB

1. What is the purpose of this lab?

2. What information is given by the coefficients in chemical reactions?

3. What is a ratio? Give an everyday example of a ratio.

4. How are ratios related to chemical reactions?

5. How can you show that mass is conserved in a chemical reaction?

OBJECTIVE

1. understand mole-mass relationships in chemical reactions. 2. demonstrate the difference between the experimental mass of the product of a chemical reaction and the theoretical mass predicted for that product by calculation.

EQUIPMENT

Balance

burner

spatula

evaporating dish

Ring stand

iron ring

wire gauze

watch glass

safety goggles/apron

MATERIALS 6M hydrochloric acid (HCl)

sodium hydrogen carbonate (NaHCO3)

SAFETY

GOGGLES AND APRONS MUST BE WORN. BE CAUTIOUS IN HANDLING HOT GLASSWARE.

Handle hydrochloric acid with care. Flush any spills with cold water and dilute solution of sodium bicarbonate and report to your teacher immediately. Never lean over an apparatus, or set up apparatus near lab top edge.

PROCEDURE

1. Flame dry a clean evaporating dish by heating it in the hot part of a burner flame for about 5 minutes. Allow the dish to cool.

2. Find the combined mass of the evaporating dish plus a watch glass. This is mass (a) in your list of data.

3. Leaving the watch glass and evaporating dish on the balance, add 2.50 g sodium hydrogen carbonate (NaHCO3) to the evaporating dish until the scale balances. Record this mass as (b) in your list of data.

4. Set up the ring stand, ring and wire gauze as shown in Fig.16.1. Place the watch glass on top of the evaporating dish and place the dish on the wire gauze.

5. Obtain about 5 Ml of 6M hydrochloric acid (HCl). CAUTION: Handle this acid carefully. It can cause painful burns if it touches your skin. Slowly add HCl to the NaHCO3 in the evaporating dish, a few drops at a time (see Fig.16.2). Continue adding acid until the reaction (bubbling) stops. Carefully tilt the evaporating dish back and forth a couple of times to make sure that the acid has contacted all the NaHCO3. After making sure that all bubbling has stopped, remove the watch glass and place it curved side up on the lab bench.

6. Holding the burner in your hand, gently heat the evaporating dish. Use a low flame and move the burner back and forth to avoid spattering. When almost all the liquid is gone remove the burner and replace the watch glass on the evaporating dish, leaving the small opening for vapor to escape. Heat gently again until no liquid remains. Allow the dish to cool.

7. Find the combined mass of the watch glass, evaporating dish and contents (NaCl). Record this mass, I, in your list of data

CONCLUSION

1. According to the balanced equation for the reaction used in this experiment, what is the ratio of moles of NaHCO3 to moles of NaCl? 2. Using your data, calculate, the moles of NaHCO3 you used and the moles of NaCl that formed in this experiment? What is the mole ratio? Is it the same as the ratio, obtained from the balanced equation? 3. What is the % yield? How do the theoretical yield and the actual yield compare? What might be the source of error if yield is less than 100%? if it is greater than 100%? 4. If the masses of all but one of the substances that take part in a chemical reaction are known, explain, why is it possible to determine the unknown mass by subtraction?

26. CHANGES IN PHYSICAL STATE

A pure substance can exist in three physical states: solid, liquid, and vapor (gaseous). Changes in physical state occur at constant, discrete temperatures that are characteristic of the substance. Changes in physical state include solids melting, liquids freezing and boiling, and gases condensing. In this experiment you will examine what happens when a pure substance, an organic compound called Lauric acid or CH3(CH2)10COOH, undergoes a change in state. This substance is a waxy solid at room temperature.

In Part I, the substance will be melted