• Resistant to UV rays• Internal and external flooring and walls• Water-resistant – Drop effect, water-resistant, non-

absorbent and does not change colour• Patented – International patent no. 1403659 from

31/10/2013• Bacteriostatic – CSTB-tested. Prevents the proliferation of

bacteria and moulds• Stain proof – Tested by the Italian Ceramic Center –

Bologna (Centro Ceramico Bologna). Can be cleaned easily• Complies with HACCP/EC 852/2004 requirements for food

hygiene• Catas-tested for colour durability in external applications

PRODUCT STRENGTHS

- Water-based, limits the risk of loads that could be harmful and dangerous to the environment during storage and transportation

ECO NOTES

UseWater-resistant grouting of joints from 0 to 5 mm with high chemical and mechanical resistance and a high level of hardness. Bonding of glass mosaic.

Materials to be grouted:- porcelain tiles, low thickness slabs, ceramic tiles, klinker, cotto, glass and ceramic mosaic, of all types and formats- natural stone, recomposed materials, marble

Flooring and walls, for internal and external use, domestic, commercial and industrial applications and street furniture subject to permanent or occasional contact with chemical substances, in environments subject to heavy traffic, swimming pools, thermal water baths and fountains, heated floors, also in areas subject to thermal shock and freezing.

Field of application Directive CE MEDEnvironmentally compatible grout and adhesive ceramized used as adhesive and/or as sealant between tiles. Maximum mass per area 1475 g/m²Thickness as adhesive layer 0,9 ± 0,1 mmThickness as sealant between tiles 3,9 ± 0,1 mmAs finishing material for all exposed interior and concealed or inacessible surfaces. When intended for bulkhead and ceiling, the product may be applied to any non-combustible support having a thickness equal or greater than 10 mm and a density ≥ 656 kg/m³. When intended for decks the product may applied to any metallic support, any non combustibile support an any material having low flame spread characteristics.

Do not useOn joints more than 5 mm in width, on porous flooring for which more specific or alternative chemical resistances are required compared with those listed in the chemical resistances table, to grout elastic expansion or fractionizing joints or on substrates that are not fully dry and subject to moisture rising.

AREAS OF USE

Fugalite® Bio - Category: Organic Mineral products - Class: Organic mineral grouts - Rating*: Eco 3

* Rating based on average colour formulations

GREENBUILDING RATING®

RATING SYSTEM ACCREDITED BY CERTIFICATION BODY SGS

0066

1Fug

alite

® B

io C

ode:

P96

3 20

16/1

0 - U

K

Water-based hypo-allergenic resin for waterproof, stain-proof, silk-effect grouting of porcelain tiles, natural stones and glass mosaic.

Fugalite® Bio is dermatologically-tested, with the result as hypoallergenic according to a skin tolerance medical experiment conducted at the University of Modena and Reggio Emilia dermatological clinic. Available in 12 natural shades inspired by the collections mainly used for making contemporary ceramic coverings. Guarantees the aesthetic and functional continuity of grouted surfaces.

LAYING RANGE / Organic mineral grouts for ceramic tiles and natural stone

KERA

KOLL MONOPACK

AB

S Y S T E M

* Centro Ceramico Bologna has passed the test for Resistance to stains following UNI EN ISO 10545-14 (Test Report N° 3686/11)

Fugalite® Bio

Regional Mineral ≥

30

% IAQVOCIndoor Air Qualit

y

Low Emission

Solvent ≤ 5 g/kg

SLVREDUCED

Low Ecologica l Im

pact

Health Care

Very low VOC emissions

Reduced solvent content2,4 g/kg

Non-toxic and non-hazardous

3

®

T E S T E D

C O L O R

HY

POALLERGEN

IC

TESTED

INTE

RNATIONAL PATEN

T

FUG A LITE BIO

n. 1403659filing date

31/10/2013

*

CO

NTRIBUTES TO

P O I N T SISO/TS 14067 COMPLIANT

Carbon Footprint

eq

kg CO2 eq/m2

0,50

PREPARATION OF SUBSTRATESBefore grouting joints, check that tiles have been laid correctly and are anchored perfectly to the substrate. Substrates must be perfectly dry. Grout joints in accordance with the recommended waiting time indicated on the relative data sheet for the adhesive used. For mortar substrates, wait at least 7 – 14 days depending on screed thickness, ambient weather conditions and on the level of absorption of the covering and the substrate. Any water or moisture rising can cause vapour pressure to accumulate, which may in turn loosen the tiles on account of the complete non-absorbency of the grout or of the tiles themselves. Joints must be free from any excess adhesive, even if already hardened. Furthermore they must be of an even depth for the whole width of the tile covering, thereby ensuring maximum chemical resistance. Any dust and loose debris must be removed from joints by carefully cleaning them with vacuum cleaner. The surface of the coating material to be grouted must be dry and free from dust or building dirt; any residual protective coatings must first be removed using specific products.Before grouting joints, check the cleanability of the tile covering, as porous or highly micro-porous surfaces may make cleaning difficult. It is advisable to perform a preliminary test on tiles not to be laid or in a small, concealed area.

SHELF LIFE3 kg monopack (part A 2 kg : part B 1 kg).It is recommended that the packs are stored at +20 °C for two days prior to use; higher temperatures increase the hardening speed, while lower temperatures make the mix hard to lay and slow down setting.

PREPARATIONMix 1 kg of component B with a spreader, pour it all into the bucket of component A, making sure that none of component B is left in the tin.Mix the two components using a low-speed helicoidal agitator until a smooth, even coloured mixture is obtained.Use a spreader to scrape the walls and bottom of the bucket of component A once component B has been poured into it, so that there are no areas of product that have not been properly mixed. Mixing by hand is not recommended. The mixture remains workable for approximately 45 min. (value calculated at +23 °C, R.H. 50%).

APPLICATIONFugalite® Bio must be applied evenly on the tile covering with a hard rubber spreader. Grout material has to be completely filled between entire joint areas, the application has to be done diagonally with respect to the joints. If grouting is to be on joints only, it is recommended that a test be carried out in advance before laying to ensure the surface can be properly cleaned. Remove most of the excess grout immediately using the spreader, leaving only a thin film on the tile.

CLEANINGPreparation

1 First cleaning with rubber spreader: once the joints have been filled, remove any excess grout that is left on the tiles immediately with the rubber spreader (working diagonally).

2 Addition of Fuga-Wash Eco to the cleaning water. Recommended dosage: 1 measuring cap for every 5 litres of water. Use the wash-boy ➀ to carry out the first cleaning pass with a cellulose sponge or abrasive felt pad, removing any excess grout from the flooring. Use wash-boy ➁ to carry out the second and final cleaning pass, finishing and smoothing the grout in the joint. Change the washing water frequently so that it is always clean. Replace the sponge or felt pad if they become impregnated with product.

First pass

3 Cleaning with cellulose sponge: clean when the grout is still fresh, using a cellulose sponge dampened with the water from tray ➀. Use circular movements to soften the film of grout on the tiles and finish the joints. Collect up the emulsion formed on the tiles using the sponge.

4 Cleaning with abrasive felt pad for structured surfaces: for more structured surfaces, clean when the grout is still fresh, using a felt pad dampened with the water from tray ➀. Use circular movements to soften the film of grout on the tiles and finish the joints. Collect up the emulsion formed on the tiles using the sponge.

Second pass

5 Finishing with a cellulose sponge: finish cleaning with a cellulose sponge dampened with water from tray ➁, working diagonally to the tiles so as not to dig into the joints. Do not walk on the damp floors for at least 12 - 24 hours, to avoid leaving dirt.

6 Finishing with foam rubber sponge for a smoother joint: for a smooth finish, complete cleaning with a foam rubber sponge dampened with water from tray ➁, working diagonally to the tiles so as not to dig into the joints.

INSTRUCTIONS FOR USE AS GROUT

1 2

1 2

3 4

option for

structured surfaces

5 6

option for

a smoother finish

0066

1Fug

alite

® B

io C

ode:

P96

3 20

16/1

0 - U

K

The level of slide for Fugalite® Bio can be improved when applying with low temperature coverings, or when the product itself has a low temperature, by diluting up to 2 % with clean water (about an espresso coffee cup for each 3 kg bucket).Adding Fuga-Wash Eco to the cleaning water gives a better detergent action on coating materials, keeps the sponge cleaner, improves the surface finish of grouting and cleans effectively without the need for rinsing.

SPECIAL NOTES

PREPARATION OF SUBSTRATESSubstrates must be compact and solid, free of dust, oil and grease, dry and free from moisture rising, with no loose debris or flaky parts such as residues of cement, lime and paint coatings, which must be completely removed. The substrate must be stable, without cracks and have already completed the curing period of hygrometric shrinkage. Uneven areas must be corrected with suitable smoothing and finishing products. On screeds and plasters which are highly absorbent and have dusty, flaky surfaces, it is advisable to apply one or more coats of Primer A Eco water-based, eco-friendly surface isolation primer, following the instructions provided, in order to reduce the water absorption and improve spreadability of the adhesive.

APPLICATIONFugalite® Bio can be applied with a suitable toothed spreader, to be chosen according to the size and type of mosaic. Using the smooth part of the spreader, apply a fine layer of product, pressing down onto the substrate in order to ensure maximum adhesion, after which the thickness can be adjusted as required by tilting the spreader at an angle. Apply the adhesive to a surface area that will allow laying of the coating material within the open time indicated. Press down the pieces of mosaic using a rubber coated spreader to allow for maximum coverage of the surface.

CLEANINGResidual traces of grout can be removed from tools with water before the product has hardened.

INSTRUCTIONS FOR USE AS ADHESIVE FOR GLASS MOSAIC

CLEANING ON THE FOLLOWING DAY

1 Once the grout has dried, any traces of dirt and streaks can be removed using Fuga-Soap Eco, to be diluted in accordance with the amount of grout to be removed and the curing time for Fugalite®. Recommended dosage: 2 - 3 parts water to 1 part Fuga-Soap Eco on the day after; undiluted after 3 days.

2 Distribute the product over the surface to be treated, using the abrasive felt pad and leaving a thin, even film of liquid. Leave Fuga-Soap Eco to work for about 10/30 minutes. After this, clean the surface manually with abrasive felt pad.

3 Collect up the detergent solution with the sponge, rubber scraper or liquid vacuum system for large surfaces. Rinse thoroughly with clean water.

4 Dry immediately with a dry cloth or liquid vacuum system, without allowing the residual water to evaporate.

Repeat for highly stubborn dirt.

SPECIAL CLEANINGWhen the grout has hardened (after at least 7 days), any residue and streaks can be removed using Fuga-Shock Eco.Distribute the product undiluted over the surface to be treated, using the abrasive felt pad. Leave Fuga-Shock Eco to act for approximately 2 - 5 minutes, then carry out the same rinsing and drying operations indicated for cleaning on the day after application.

INSTRUCTIONS FOR USE AS GROUT

1

3

2

4

0066

1Fug

alite

® B

io C

ode:

P96

3 20

16/1

0 - U

K

Appearance part A coloured paste / part B neutral pasteSpecific weight Part A ≈ 1.53 kg/dm³ / Part B ≈ 1.50 kg/dm³Viscosity ≈ 120000 mPa · s, rotor 93 RPM 10 Brookfield methodMineralogical nature of inert material silicate - crystallineChemical nature epoxy resin (part A) / polyamines (part B)Grading ≈ 0 – 250 µmShelf life ≈ 18 months in the original packagingWarning Protect from frost, avoid direct exposure to sunlight and sources of heatPack Part A: 2 kg bucket / Part B: 1 kg bucketMixing ratio Part A : Part B = 1 : 0,5Specific weight of the mixture ≈ 1,512 kg/dm3

Pot life at +23 °C ≥ 45 min.Temperature range for application from +5 °C to +30 °CWidth of joints from 0 to 5 mmFoot traffic: ≈ 24 hrsGrouting after laying:- with Fugalite® Bio on coating materials immediate- with Fugalite® Bio on floors as soon as foot traffic is allowed- with adhesive see characteristics of adhesive- mortar ≈ 7 – 14 daysInterval before normal use ≈ 3 days (mechanical resistance) / ≈ 7 days (chemical resist.)Coverage- as an adhesive ≈ 2 – 4 kg/m2

- as a grout see Coverage tableValues taken at +23 °C, 50% R.H. and no ventilation. Data may vary depending on specific conditions at the building site, i.e.temperature, ventilation and absorbency level of the substrate and of the materials laid.

TECHNICAL DATA COMPLIANT WITH KERAKOLL QUALITY STANDARD

Format Thicknessgrammes/m² joint width

1 mm 2 mm 5 mm

Mosaic 2x2 cm 3 mm ≈ 560 ≈ 1.120 ≈ 2.800

5x5 cm 4 mm ≈ 305 ≈ 610 ≈ 1.525

Tiles 30x60 cm 4 mm ≈ 40 ≈ 80 ≈ 200

50x50 cm 4 mm ≈ 30 ≈ 60 ≈ 150

60x60 cm 4 mm ≈ 25 ≈ 50 ≈ 125

100x100 cm 4 mm ≈ 15 ≈ 30 ≈ 75

20x20 cm 8 mm ≈ 160 ≈ 320 ≈ 800

30x30 cm 9 mm ≈ 115 ≈ 230 ≈ 575

40x40 cm 10 mm ≈ 95 ≈ 190 ≈ 475

30x60 cm 10 mm ≈ 95 ≈ 190 ≈ 475

60x60 cm 10 mm ≈ 65 ≈ 130 ≈ 325

60x90 cm 10 mm ≈ 55 ≈ 110 ≈ 275

100x100 cm 10 mm ≈ 40 ≈ 80 ≈ 200

120x120 cm 10 mm ≈ 30 ≈ 60 ≈ 150

20x20 cm 14 mm ≈ 270 ≈ 540 ≈ 1.350

30x30 cm 14 mm ≈ 180 ≈ 360 ≈ 900

Klinker 30x30 cm 15 mm ≈ 195 ≈ 390 ≈ 975

12,5x24,5 cm 12 mm ≈ 280 ≈ 560 ≈ 1.400

COVERAGE TABLE

0066

1Fug

alite

® B

io C

ode:

P96

3 20

16/1

0 - U

K

VOC INDOOR AIR QUALITY (IAQ) - VOLATILE ORGANIC COMPOUND EMISSIONSConformity EC 1-R plus GEV-Emicode GEV certified 5205/11.01.02HIGH-TECHStatic modulus of elasticity ≈ 1230 MPa ISO 178Resistance to abrasion ≈ 203 mm3 EN 12808-2Water absorption after 240 min. ≈ 0,06 g EN 12808-5Working temperature from -40 °C to +80 °CColour fastness according to UNI EN ISO 105-A05 see tableResistance to bacterial contamination class B+ CSTB 2010-081Porcelain tiles/concrete tensile strength ≥ 2,5 N/mm2 EN 1348Initial shear strength ≥ 5 N/mm2 EN 12003Shear strength after water immersion ≥ 5 N/mm2 EN 12003Shear strength after thermal shock ≥ 2 N/mm2 EN 12003Open time: tensile adhesion ≥ 3 N/mm2 EN 1346Resistance to iodine stains class 4 ISO 10545-14Resistance to olive oil stains class 5 ISO 10545-14Resistance to chromium stains class 3 ISO 10545-14Values taken at +23 °C, 50% R.H. and no ventilation. Data may vary depending on specific conditions at the building site.

PERFORMANCE

Values taken at: – ambient +23 °C / 50% R.H. – chemical aggressive agent +23 °C

N.B. Only mechanical resistance after chemical attack.

Legend ••• Excellent•• Good• poor

Acids Concentration Permanent contact Occasional contact

Acetic 2,5% • •••

5% • ••

10% • •

Hydrochloric 37% •• •••

Citric 10% •• •••

Formic 2,5% • •

10% • •

Phosphoric 50% •• •••

75% • ••

Lactic 2,5% • •••

5% • ••

10% • •

Nitric 25% • ••

50% • •

Oleic 100% • •

Sulphuric 50% ••• •••

100% • •

Tannic 10% •• •••

Tartaric 10% •• •••

CHEMICAL RESISTANCE (EN 12808-1)

0066

1Fug

alite

® B

io C

ode:

P96

3 20

16/1

0 - U

K

Values taken at: – ambient +23 °C / 50% R.H. – chemical aggressive agent +23 °C

N.B. Only mechanical resistance after chemical attack.

CHEMICAL RESISTANCE (EN 12808-1)

Legend ••• Excellent•• Good• poor

FoodstuffsMain foodstuffs

(temporary contact)

Vinegar ••

Citrus fruits ••

Ethyl alcohol ••

Beer •••

Butter •••

Coffee •••

Casein •••

Glucose •••

Animal fat •••

Fresh milk ••

Malt •••

Margarine •••

Olive oil •••

Soya oil •••

Pectin •••

Tomato ••

Yoghurt ••

Sugar •••

Fuels and Oils Permanent contact Occasional contact

Petrol • •••

Diesel oil •• •••

Coal tar oil •• ••

Mineral oil •• •••

Petroleum ••• •••

mineral spirit • ••

Turpentine • ••

Alkalis and Salts Concentration Permanent contact Occasional contact

Oxygenated water10% •• •••

25% • •••

Ammonia 25% • •••

Calcium chloride Saturated Sol. ••• •••

Sodium chloride Saturated Sol. ••• •••

Sodium hypochlorite(Active chlorine)

1,5% • •••

13% • •

Caustic soda 50% ••• •••

Aluminium sulphate Saturated Sol. ••• •••

Potassium hydroxide 50% ••• •••

Potassium permanganate 5% •• ••

10% • •

0066

1Fug

alite

® B

io C

ode:

P96

3 20

16/1

0 - U

K

Values taken at: – ambient +23 °C / 50% R.H. – chemical aggressive agent +23 °C

N.B. Only mechanical resistance after chemical attack.

CHEMICAL RESISTANCE (EN 12808-1)

Legend ••• Excellent•• Good• poor

Solvents Permanent contact Occasional contact

Acetone • •

Ethyl alcohol • •••

Benzol • ••

Chloroform • •

Methylene chloride • •

Ethylene glycol ••• •••

Perchloroethylene • ••

Carbon tetrachloride • ••

Tetrahydrofuran • •

Toluol • ••

Trichloroethylene • •

Xylene • ••

Legend

5 can be cleaned under a running hot tap while gently rubbing with a sponge4 can be cleaned with a mild detergent while gently rubbing with a sponge3 can be cleaned with a basic detergent while vigorously rubbing with a sponge2 to clean, treat first with a solvent or aggressive acid or basic solution, then vigorously rub with a sponge1 cannot be cleaned by any of the aforementioned methods

RESISTANCE TO STAINS (ISO 10545-14)

Staining agentsTime exposed to staining agent:

24 hoursTime exposed to staining agent:

30 min.

Red wine 3 3

Mineral oil 5 5

Tomato ketchup 2 5

Mascara 5 5

Coffee 2 5

Hair dye 1 2

0066

1Fug

alite

® B

io C

ode:

P96

3 20

16/1

0 - U

K

The Eco and Bio classifications refer to the GreenBuilding Rating® Manual 2012. This information was last updated in September 2016 (ref. GBR Data Report - 10.16); please note that additions and/or amendments may be made over time by KERAKOLL SpA; for the latest version, see www.kerakoll.com. CFP Technical data available on External Communication Report 10-2014. KERAKOLL SpA shall therefore be liable for the validity, accuracy and updating of information provided only when taken directly from its institutional website. The technical data sheet given here is based on our technical and practical knowledge. As it is not possible for us to directly check the conditions in your building yards and the execution of the work, this information represents general indications that do not bind Kerakoll in any way. Therefore, it is advisable to perform a preliminary test to verify the suitability of the product for your purposes.

KERAKOLL UK Ltd.Unit 4, The Croft, Buntsford Gate Business ParkBromsgrove, Worcestershire B60 4JE, United KingdomTel +44 01527 578000 - Fax +44 01527 578170info@kerakoll.co.uk - www.kerakoll.com

- Product for professional use- use at temperatures between +5 °C and +30 °C- use packs which have been stored for 2/3 days before use at +20 °C- respect the mixing ratio of 2 : 1. For partial mixing, weigh the two parts precisely- workability times may vary considerably, depending on ambient conditions and the temperature of the tiles- do not walk on floors that are still damp as dirt could still stick to them- do not lay on substrates subject to moisture rising or which are not completely dry- if necessary, ask for the safety data sheet- for any other issues, contact the Kerakoll Worldwide Global Service 01527 578000 - info@kerakoll.co.uk

WARNING

COLOUR CHART

from 5 to 4 high colour fastness; for internal and external usefrom 3.5 to 3 good colour fastness; for internal and external usefrom 2.5 to 1 limited colour fastness; for internal use

Legend

Fugalite® Bio colours Colour Fastness* GSc (Daylight)EN ISO 105-A05 standard

Clas

sic

01 White 4

02 Light Grey 4

03 Pearl Grey 4

04 Iron Grey 4,5

05 Anthracite 4,5

06 Black 4,5

07 Jasmin 3,5

08 Bahama Beige 4

12 Walnut 4,5

Desi

gn

51 Silver 4

46 Ivory 3,5

Colo

rs

15 Ocean 3,5

The shades shown are intended as an indication only.

0066

1Fug

alite

® B

io C

ode:

P96

3 20

16/1

0 - U

K

• Resistant to UV rays• Internal and external flooring and walls• Water-resistant – Drop effect, water-resistant, non-

absorbent and does not change colour• Patented – International patent no. 1403659 from

31/10/2013• Bacteriostatic – CSTB-tested. Prevents the proliferation of

bacteria and moulds• Stain proof – Tested by the Italian Ceramic Center –

Bologna (Centro Ceramico Bologna). Can be cleaned easily• Complies with HACCP/EC 852/2004 requirements for food

hygiene• Catas-tested for colour durability in external applications

PRODUCT STRENGTHS

- Water-based, limits the risk of loads that could be harmful and dangerous to the environment during storage and transportation

ECO NOTES

UseWater-resistant grouting of joints from 0 to 5 mm with high chemical and mechanical resistance and a high level of hardness. Bonding of glass mosaic.

Materials to be grouted:- porcelain tiles, low thickness slabs, ceramic tiles, klinker, cotto, glass and ceramic mosaic, of all types and formats- natural stone, recomposed materials, marble

Flooring and walls, for internal and external use, domestic, commercial and industrial applications and street furniture subject to permanent or occasional contact with chemical substances, in environments subject to heavy traffic, swimming pools, thermal water baths and fountains, heated floors, also in areas subject to thermal shock and freezing.

Field of application Directive CE MEDEnvironmentally compatible grout and adhesive ceramized used as adhesive and/or as sealant between tiles. Maximum mass per area 1475 g/m²Thickness as adhesive layer 0,9 ± 0,1 mmThickness as sealant between tiles 3,9 ± 0,1 mmAs finishing material for all exposed interior and concealed or inacessible surfaces. When intended for bulkhead and ceiling, the product may be applied to any non-combustible support having a thickness equal or greater than 10 mm and a density ≥ 656 kg/m³. When intended for decks the product may applied to any metallic support, any non combustibile support an any material having low flame spread characteristics.

Do not useOn joints more than 5 mm in width, on porous flooring for which more specific or alternative chemical resistances are required compared with those listed in the chemical resistances table, to grout elastic expansion or fractionizing joints or on substrates that are not fully dry and subject to moisture rising.

AREAS OF USE

Fugalite® Bio - Category: Organic Mineral products - Class: Organic mineral grouts - Rating*: Eco 3

* Rating based on average colour formulations

GREENBUILDING RATING®

RATING SYSTEM ACCREDITED BY CERTIFICATION BODY SGS

0066

1Fug

alite

® B

io C

ode:

P96

3 20

16/1

0 - U

K

Water-based hypo-allergenic resin for waterproof, stain-proof, silk-effect grouting of porcelain tiles, natural stones and glass mosaic.

Fugalite® Bio is dermatologically-tested, with the result as hypoallergenic according to a skin tolerance medical experiment conducted at the University of Modena and Reggio Emilia dermatological clinic. Available in 12 natural shades inspired by the collections mainly used for making contemporary ceramic coverings. Guarantees the aesthetic and functional continuity of grouted surfaces.

LAYING RANGE / Organic mineral grouts for ceramic tiles and natural stone

KERA

KOLL MONOPACK

AB

S Y S T E M

* Centro Ceramico Bologna has passed the test for Resistance to stains following UNI EN ISO 10545-14 (Test Report N° 3686/11)

Fugalite® Bio

Regional Mineral ≥

30

% IAQVOCIndoor Air Qualit

y

Low Emission

Solvent ≤ 5 g/kg

SLVREDUCED

Low Ecologica l Im

pact

Health Care

Very low VOC emissions

Reduced solvent content2,4 g/kg

Non-toxic and non-hazardous

3

®

T E S T E D

C O L O R

HY

POALLERGEN

IC

TESTED

INTE

RNATIONAL PATEN

T

FUG A LITE BIO

n. 1403659filing date

31/10/2013

*

CO

NTRIBUTES TO

P O I N T SISO/TS 14067 COMPLIANT

Carbon Footprint

eq

kg CO2 eq/m2

0,50

PREPARATION OF SUBSTRATESBefore grouting joints, check that tiles have been laid correctly and are anchored perfectly to the substrate. Substrates must be perfectly dry. Grout joints in accordance with the recommended waiting time indicated on the relative data sheet for the adhesive used. For mortar substrates, wait at least 7 – 14 days depending on screed thickness, ambient weather conditions and on the level of absorption of the covering and the substrate. Any water or moisture rising can cause vapour pressure to accumulate, which may in turn loosen the tiles on account of the complete non-absorbency of the grout or of the tiles themselves. Joints must be free from any excess adhesive, even if already hardened. Furthermore they must be of an even depth for the whole width of the tile covering, thereby ensuring maximum chemical resistance. Any dust and loose debris must be removed from joints by carefully cleaning them with vacuum cleaner. The surface of the coating material to be grouted must be dry and free from dust or building dirt; any residual protective coatings must first be removed using specific products.Before grouting joints, check the cleanability of the tile covering, as porous or highly micro-porous surfaces may make cleaning difficult. It is advisable to perform a preliminary test on tiles not to be laid or in a small, concealed area.

SHELF LIFE3 kg monopack (part A 2 kg : part B 1 kg).It is recommended that the packs are stored at +20 °C for two days prior to use; higher temperatures increase the hardening speed, while lower temperatures make the mix hard to lay and slow down setting.

PREPARATIONMix 1 kg of component B with a spreader, pour it all into the bucket of component A, making sure that none of component B is left in the tin.Mix the two components using a low-speed helicoidal agitator until a smooth, even coloured mixture is obtained.Use a spreader to scrape the walls and bottom of the bucket of component A once component B has been poured into it, so that there are no areas of product that have not been properly mixed. Mixing by hand is not recommended. The mixture remains workable for approximately 45 min. (value calculated at +23 °C, R.H. 50%).

APPLICATIONFugalite® Bio must be applied evenly on the tile covering with a hard rubber spreader. Grout material has to be completely filled between entire joint areas, the application has to be done diagonally with respect to the joints. If grouting is to be on joints only, it is recommended that a test be carried out in advance before laying to ensure the surface can be properly cleaned. Remove most of the excess grout immediately using the spreader, leaving only a thin film on the tile.

CLEANINGPreparation

1 First cleaning with rubber spreader: once the joints have been filled, remove any excess grout that is left on the tiles immediately with the rubber spreader (working diagonally).

2 Addition of Fuga-Wash Eco to the cleaning water. Recommended dosage: 1 measuring cap for every 5 litres of water. Use the wash-boy ➀ to carry out the first cleaning pass with a cellulose sponge or abrasive felt pad, removing any excess grout from the flooring. Use wash-boy ➁ to carry out the second and final cleaning pass, finishing and smoothing the grout in the joint. Change the washing water frequently so that it is always clean. Replace the sponge or felt pad if they become impregnated with product.

First pass

3 Cleaning with cellulose sponge: clean when the grout is still fresh, using a cellulose sponge dampened with the water from tray ➀. Use circular movements to soften the film of grout on the tiles and finish the joints. Collect up the emulsion formed on the tiles using the sponge.

4 Cleaning with abrasive felt pad for structured surfaces: for more structured surfaces, clean when the grout is still fresh, using a felt pad dampened with the water from tray ➀. Use circular movements to soften the film of grout on the tiles and finish the joints. Collect up the emulsion formed on the tiles using the sponge.

Second pass

5 Finishing with a cellulose sponge: finish cleaning with a cellulose sponge dampened with water from tray ➁, working diagonally to the tiles so as not to dig into the joints. Do not walk on the damp floors for at least 12 - 24 hours, to avoid leaving dirt.

6 Finishing with foam rubber sponge for a smoother joint: for a smooth finish, complete cleaning with a foam rubber sponge dampened with water from tray ➁, working diagonally to the tiles so as not to dig into the joints.

INSTRUCTIONS FOR USE AS GROUT

1 2

1 2

3 4

option for

structured surfaces

5 6

option for

a smoother finish

0066

1Fug

alite

® B

io C

ode:

P96

3 20

16/1

0 - U

K

The level of slide for Fugalite® Bio can be improved when applying with low temperature coverings, or when the product itself has a low temperature, by diluting up to 2 % with clean water (about an espresso coffee cup for each 3 kg bucket).Adding Fuga-Wash Eco to the cleaning water gives a better detergent action on coating materials, keeps the sponge cleaner, improves the surface finish of grouting and cleans effectively without the need for rinsing.

SPECIAL NOTES

PREPARATION OF SUBSTRATESSubstrates must be compact and solid, free of dust, oil and grease, dry and free from moisture rising, with no loose debris or flaky parts such as residues of cement, lime and paint coatings, which must be completely removed. The substrate must be stable, without cracks and have already completed the curing period of hygrometric shrinkage. Uneven areas must be corrected with suitable smoothing and finishing products. On screeds and plasters which are highly absorbent and have dusty, flaky surfaces, it is advisable to apply one or more coats of Primer A Eco water-based, eco-friendly surface isolation primer, following the instructions provided, in order to reduce the water absorption and improve spreadability of the adhesive.

APPLICATIONFugalite® Bio can be applied with a suitable toothed spreader, to be chosen according to the size and type of mosaic. Using the smooth part of the spreader, apply a fine layer of product, pressing down onto the substrate in order to ensure maximum adhesion, after which the thickness can be adjusted as required by tilting the spreader at an angle. Apply the adhesive to a surface area that will allow laying of the coating material within the open time indicated. Press down the pieces of mosaic using a rubber coated spreader to allow for maximum coverage of the surface.

CLEANINGResidual traces of grout can be removed from tools with water before the product has hardened.

INSTRUCTIONS FOR USE AS ADHESIVE FOR GLASS MOSAIC

CLEANING ON THE FOLLOWING DAY

1 Once the grout has dried, any traces of dirt and streaks can be removed using Fuga-Soap Eco, to be diluted in accordance with the amount of grout to be removed and the curing time for Fugalite®. Recommended dosage: 2 - 3 parts water to 1 part Fuga-Soap Eco on the day after; undiluted after 3 days.

2 Distribute the product over the surface to be treated, using the abrasive felt pad and leaving a thin, even film of liquid. Leave Fuga-Soap Eco to work for about 10/30 minutes. After this, clean the surface manually with abrasive felt pad.

3 Collect up the detergent solution with the sponge, rubber scraper or liquid vacuum system for large surfaces. Rinse thoroughly with clean water.

4 Dry immediately with a dry cloth or liquid vacuum system, without allowing the residual water to evaporate.

Repeat for highly stubborn dirt.

SPECIAL CLEANINGWhen the grout has hardened (after at least 7 days), any residue and streaks can be removed using Fuga-Shock Eco.Distribute the product undiluted over the surface to be treated, using the abrasive felt pad. Leave Fuga-Shock Eco to act for approximately 2 - 5 minutes, then carry out the same rinsing and drying operations indicated for cleaning on the day after application.

INSTRUCTIONS FOR USE AS GROUT

1

3

2

4

0066

1Fug

alite

® B

io C

ode:

P96

3 20

16/1

0 - U

K

Appearance part A coloured paste / part B neutral pasteSpecific weight Part A ≈ 1.53 kg/dm³ / Part B ≈ 1.50 kg/dm³Viscosity ≈ 120000 mPa · s, rotor 93 RPM 10 Brookfield methodMineralogical nature of inert material silicate - crystallineChemical nature epoxy resin (part A) / polyamines (part B)Grading ≈ 0 – 250 µmShelf life ≈ 18 months in the original packagingWarning Protect from frost, avoid direct exposure to sunlight and sources of heatPack Part A: 2 kg bucket / Part B: 1 kg bucketMixing ratio Part A : Part B = 1 : 0,5Specific weight of the mixture ≈ 1,512 kg/dm3

Pot life at +23 °C ≥ 45 min.Temperature range for application from +5 °C to +30 °CWidth of joints from 0 to 5 mmFoot traffic: ≈ 24 hrsGrouting after laying:- with Fugalite® Bio on coating materials immediate- with Fugalite® Bio on floors as soon as foot traffic is allowed- with adhesive see characteristics of adhesive- mortar ≈ 7 – 14 daysInterval before normal use ≈ 3 days (mechanical resistance) / ≈ 7 days (chemical resist.)Coverage- as an adhesive ≈ 2 – 4 kg/m2

- as a grout see Coverage tableValues taken at +23 °C, 50% R.H. and no ventilation. Data may vary depending on specific conditions at the building site, i.e.temperature, ventilation and absorbency level of the substrate and of the materials laid.

TECHNICAL DATA COMPLIANT WITH KERAKOLL QUALITY STANDARD

Format Thicknessgrammes/m² joint width

1 mm 2 mm 5 mm

Mosaic 2x2 cm 3 mm ≈ 560 ≈ 1.120 ≈ 2.800

5x5 cm 4 mm ≈ 305 ≈ 610 ≈ 1.525

Tiles 30x60 cm 4 mm ≈ 40 ≈ 80 ≈ 200

50x50 cm 4 mm ≈ 30 ≈ 60 ≈ 150

60x60 cm 4 mm ≈ 25 ≈ 50 ≈ 125

100x100 cm 4 mm ≈ 15 ≈ 30 ≈ 75

20x20 cm 8 mm ≈ 160 ≈ 320 ≈ 800

30x30 cm 9 mm ≈ 115 ≈ 230 ≈ 575

40x40 cm 10 mm ≈ 95 ≈ 190 ≈ 475

30x60 cm 10 mm ≈ 95 ≈ 190 ≈ 475

60x60 cm 10 mm ≈ 65 ≈ 130 ≈ 325

60x90 cm 10 mm ≈ 55 ≈ 110 ≈ 275

100x100 cm 10 mm ≈ 40 ≈ 80 ≈ 200

120x120 cm 10 mm ≈ 30 ≈ 60 ≈ 150

20x20 cm 14 mm ≈ 270 ≈ 540 ≈ 1.350

30x30 cm 14 mm ≈ 180 ≈ 360 ≈ 900

Klinker 30x30 cm 15 mm ≈ 195 ≈ 390 ≈ 975

12,5x24,5 cm 12 mm ≈ 280 ≈ 560 ≈ 1.400

COVERAGE TABLE

0066

1Fug

alite

® B

io C

ode:

P96

3 20

16/1

0 - U

K

VOC INDOOR AIR QUALITY (IAQ) - VOLATILE ORGANIC COMPOUND EMISSIONSConformity EC 1-R plus GEV-Emicode GEV certified 5205/11.01.02HIGH-TECHStatic modulus of elasticity ≈ 1230 MPa ISO 178Resistance to abrasion ≈ 203 mm3 EN 12808-2Water absorption after 240 min. ≈ 0,06 g EN 12808-5Working temperature from -40 °C to +80 °CColour fastness according to UNI EN ISO 105-A05 see tableResistance to bacterial contamination class B+ CSTB 2010-081Porcelain tiles/concrete tensile strength ≥ 2,5 N/mm2 EN 1348Initial shear strength ≥ 5 N/mm2 EN 12003Shear strength after water immersion ≥ 5 N/mm2 EN 12003Shear strength after thermal shock ≥ 2 N/mm2 EN 12003Open time: tensile adhesion ≥ 3 N/mm2 EN 1346Resistance to iodine stains class 4 ISO 10545-14Resistance to olive oil stains class 5 ISO 10545-14Resistance to chromium stains class 3 ISO 10545-14Values taken at +23 °C, 50% R.H. and no ventilation. Data may vary depending on specific conditions at the building site.

PERFORMANCE

Values taken at: – ambient +23 °C / 50% R.H. – chemical aggressive agent +23 °C

N.B. Only mechanical resistance after chemical attack.

Legend ••• Excellent•• Good• poor

Acids Concentration Permanent contact Occasional contact

Acetic 2,5% • •••

5% • ••

10% • •

Hydrochloric 37% •• •••

Citric 10% •• •••

Formic 2,5% • •

10% • •

Phosphoric 50% •• •••

75% • ••

Lactic 2,5% • •••

5% • ••

10% • •

Nitric 25% • ••

50% • •

Oleic 100% • •

Sulphuric 50% ••• •••

100% • •

Tannic 10% •• •••

Tartaric 10% •• •••

CHEMICAL RESISTANCE (EN 12808-1)

0066

1Fug

alite

® B

io C

ode:

P96

3 20

16/1

0 - U

K

Values taken at: – ambient +23 °C / 50% R.H. – chemical aggressive agent +23 °C

N.B. Only mechanical resistance after chemical attack.

CHEMICAL RESISTANCE (EN 12808-1)

Legend ••• Excellent•• Good• poor

FoodstuffsMain foodstuffs

(temporary contact)

Vinegar ••

Citrus fruits ••

Ethyl alcohol ••

Beer •••

Butter •••

Coffee •••

Casein •••

Glucose •••

Animal fat •••

Fresh milk ••

Malt •••

Margarine •••

Olive oil •••

Soya oil •••

Pectin •••

Tomato ••

Yoghurt ••

Sugar •••

Fuels and Oils Permanent contact Occasional contact

Petrol • •••

Diesel oil •• •••

Coal tar oil •• ••

Mineral oil •• •••

Petroleum ••• •••

mineral spirit • ••

Turpentine • ••

Alkalis and Salts Concentration Permanent contact Occasional contact

Oxygenated water10% •• •••

25% • •••

Ammonia 25% • •••

Calcium chloride Saturated Sol. ••• •••

Sodium chloride Saturated Sol. ••• •••

Sodium hypochlorite(Active chlorine)

1,5% • •••

13% • •

Caustic soda 50% ••• •••

Aluminium sulphate Saturated Sol. ••• •••

Potassium hydroxide 50% ••• •••

Potassium permanganate 5% •• ••

10% • •

0066

1Fug

alite

® B

io C

ode:

P96

3 20

16/1

0 - U

K

Values taken at: – ambient +23 °C / 50% R.H. – chemical aggressive agent +23 °C

N.B. Only mechanical resistance after chemical attack.

CHEMICAL RESISTANCE (EN 12808-1)

Legend ••• Excellent•• Good• poor

Solvents Permanent contact Occasional contact

Acetone • •

Ethyl alcohol • •••

Benzol • ••

Chloroform • •

Methylene chloride • •

Ethylene glycol ••• •••

Perchloroethylene • ••

Carbon tetrachloride • ••

Tetrahydrofuran • •

Toluol • ••

Trichloroethylene • •

Xylene • ••

Legend

5 can be cleaned under a running hot tap while gently rubbing with a sponge4 can be cleaned with a mild detergent while gently rubbing with a sponge3 can be cleaned with a basic detergent while vigorously rubbing with a sponge2 to clean, treat first with a solvent or aggressive acid or basic solution, then vigorously rub with a sponge1 cannot be cleaned by any of the aforementioned methods

RESISTANCE TO STAINS (ISO 10545-14)

Staining agentsTime exposed to staining agent:

24 hoursTime exposed to staining agent:

30 min.

Red wine 3 3

Mineral oil 5 5

Tomato ketchup 2 5

Mascara 5 5

Coffee 2 5

Hair dye 1 2

0066

1Fug

alite

® B

io C

ode:

P96

3 20

16/1

0 - U

K

The Eco and Bio classifications refer to the GreenBuilding Rating® Manual 2012. This information was last updated in September 2016 (ref. GBR Data Report - 10.16); please note that additions and/or amendments may be made over time by KERAKOLL SpA; for the latest version, see www.kerakoll.com. CFP Technical data available on External Communication Report 10-2014. KERAKOLL SpA shall therefore be liable for the validity, accuracy and updating of information provided only when taken directly from its institutional website. The technical data sheet given here is based on our technical and practical knowledge. As it is not possible for us to directly check the conditions in your building yards and the execution of the work, this information represents general indications that do not bind Kerakoll in any way. Therefore, it is advisable to perform a preliminary test to verify the suitability of the product for your purposes.

KERAKOLL UK Ltd.Unit 4, The Croft, Buntsford Gate Business ParkBromsgrove, Worcestershire B60 4JE, United KingdomTel +44 01527 578000 - Fax +44 01527 578170info@kerakoll.co.uk - www.kerakoll.com

- Product for professional use- use at temperatures between +5 °C and +30 °C- use packs which have been stored for 2/3 days before use at +20 °C- respect the mixing ratio of 2 : 1. For partial mixing, weigh the two parts precisely- workability times may vary considerably, depending on ambient conditions and the temperature of the tiles- do not walk on floors that are still damp as dirt could still stick to them- do not lay on substrates subject to moisture rising or which are not completely dry- if necessary, ask for the safety data sheet- for any other issues, contact the Kerakoll Worldwide Global Service 01527 578000 - info@kerakoll.co.uk

WARNING

COLOUR CHART

from 5 to 4 high colour fastness; for internal and external usefrom 3.5 to 3 good colour fastness; for internal and external usefrom 2.5 to 1 limited colour fastness; for internal use

Legend

Fugalite® Bio colours Colour Fastness* GSc (Daylight)EN ISO 105-A05 standard

Clas

sic

01 White 4

02 Light Grey 4

03 Pearl Grey 4

04 Iron Grey 4,5

05 Anthracite 4,5

06 Black 4,5

07 Jasmin 3,5

08 Bahama Beige 4

12 Walnut 4,5

Desi

gn

51 Silver 4

46 Ivory 3,5

Colo

rs

15 Ocean 3,5

The shades shown are intended as an indication only.

0066

1Fug

alite

® B

io C

ode:

P96

3 20

16/1

0 - U

K

UseWater-resistant grouting of joints with high chemical and mechanical resistance and a high level of hardness.

Materials to be grouted:- porcelain tiles, low thickness slabs, ceramic tiles, klinker, cotto, glass and ceramic mosaic, of all types and formats- recomposed materials

Flooring and walls in indoor, domestic, commercial and industrial applications subject to permanent or occasional contact with chemi-cal substances, in environments subject to heavy traffic, swimming pools, thermal water baths and fountains, also in areas subject to thermal shock and freezing.

Do not useOn porous flooring for which more specific or alternative chemical resistances are required compared with those listed in the chemical resistances table, to grout elastic expansion or fractionizing joints or on substrates that are not fully dry and subject to moisture rising.

AREAS OF USEFu

galit

e® E

co C

ode:

P77

9 20

12/0

1 UK

Certified, eco-friendly, vitrified, flowing, easy-to-clean grout, bacteriostatic and fungistatic, water and stain proof for joints of between 0 and 20 mm with a high level of chemical and mechanical resistance, guarantees the continuity of ceramic surfaces, ideal for use in GreenBuilding. With very low volatile organic compound emissions.

Fugalite® Eco is a liquid ceramic for the smooth, unbroken grouting of all ceramic and glass mosaic coverings. Available in 4 colour collections giving a total of 30 different colours and allowing unlimited creative potential and original combinations as well as a striking finish.

Fugalite® EcoLAYING RANGE / Organic Mineral Grouts for Ceramic Tiles and Natural Stone

KERA

KOLL MONOPACK

AB

S Y S T E M

CO

NTRIBUTES TO

P O I N T S

T E ST E D

C O L O R

Patent PendingIN

TERN

ATIONAL PATENT

A

PPLIC ATIO

N

PRODUCT STRENGTHS

t� Internal floors and walls

t� Suitable for porcelain tiles, ceramics, large formats, low thickness slabs and glass mosaic

t� Vitrified, guarantees the lasting performance of ceramics

t� Vitrified, easier to apply than cement-based grout

t� Vitrified, complete colour uniformity

t� Vitrified, impermeable to water, stains and dirt

t� Vitrified, prevents the development of mould and bacteria

ECO NOTES

- The use of sand formed by natural processes allows substantial energy saving by using the natural action of the wind

- The extra-fine and neutral colours contain micro glass beads made from recycled glass

GREENBUILDING RATING®

RATING SYSTEM ACCREDITED BY CERTIFICATION BODY SGS

1

®

Regional Mineral ≥

30

% IAQVOCIndoor Air Qualit

y

Low Emission

Solvent ≤ 5 g/kg

SLVREDUCED

Low Ecologica l Im

pact

Health Care

Very low VOC emissions< 20 µg/m3

Fugalite® Eco - Category: Organic Mineral Products - Class: Organic Mineral Grouts - Rating*: Eco 1

* Rating based on average colour formulations

*

* Centro Ceramico Bologna has passed the test for Resistance to stains following UNI EN ISO 10545-14 (Test Report N° 3685/11)

Preparation of substrates Before grouting joints, check that tiles have been laid correctly and are anchored perfectly to the substrate. Substrates must be perfectly dry. Grout joints in accordance with the recommended waiting time indicated on the relative data sheet for the adhesive used. For mortar substrates, wait at least 7 – 14 days depending on screed thickness, ambient weather conditions and on the level of absorption of the covering and the substrate. Any water or moisture rising can cause vapour pressure to accumulate, which may in turn loosen the tiles on account of the complete non-absorbency of the grout or of the tiles themselves.Joints must be free from any excess adhesive, even if already hardened. Furthermore they must be of an even depth for the whole width of the tile covering, thereby ensuring maximum chemical resistance. Any dust and loose debris must be removed from the joints by carefully cleaning them with a vacuum cleaner.Before grouting joints, check the cleanability of the tile covering, as porous or highly micro-porous surfaces may make cleaning difficult. It is advisable to perform a preliminary test on tiles not to be laid or in a small, concealed area. In these cases we recommend treating the covering with specific protective products, being careful to avoid applying them to the joints.

PreparationFugalite® Eco is prepared by mixing together parts A and B from the bottom upwards, using a low-rev (≈ 400/min.) helicoidal agitator, respecting the preset ratio of 2.82 : 0.18 of the packs. Pour part B into the bucket containing part A, being careful to mix the two parts uni-formly until a smooth, even coloured mixture is obtained. Mix only enough grout that can be used in full within 45 minutes at +23 ºC, 50% RH. Fugalite® Eco product buckets must be stored at a temperature of approx. 20 °C for at least 2/3 days before use. Higher temperatures make the mixture too fluid and shorten hardening times, while lower temperatures make the mixture harder to spread and slow down setting times. At temperatures of less than 5°C, the product will no longer set.

ApplicationFugalite® Eco must be applied evenly on the tile covering with a hard rubber spreader. Seal the joints by completely grouting them, applying the grout diagonally to the tiles. Remove most of the excess grout immediately using the spreader, leaving only a thin film on the tile. Begin cleaning the tilework when the grout is still fresh. On completion, clean up the surface using a thick, large-sized sponge damped in clean water to avoid removing grout from the joints. Use circular movements to soften the film of grout on the tiles and finish cleaning the joint surface. Specific high-dispersion polymers ensure all grout residues are removed using only a small amount of water, which would otherwise impair the final chemical resistances. Rinse frequently and make sure clean water is used at all times, using appropriate trays and grills with cleaning rollers. If necessary, replace the sponge or felt cleaning pad when saturated with grout. Finish cleaning up by dragging the sponge diagonally across the tiles to avoid going into the joints. Wipe the cleaned surface again with a dry cloth to make sure it is completely clean and there are no streaks of resin remaining. Once the grout has dried, any streaks can be removed using Fuga-Soap Eco, to be diluted in accordance with the number of streaks to be cleaned. Do not walk on floors that are still damp as dirt could still stick to them.

CleaningResidual traces of grout can be removed from tools with water before the product has hardened.

INSTRUCTIONS FOR USE

Gold or silver Fuga-Glitter can be used as a additive in Fugalite® Eco to create a metalized decorative effect; add 1 100 g tin to every bucket of grout to obtain a high quality aesthetic finish.

SPECIAL NOTES

Fuga

lite®

Eco

Cod

e: P

779

2012

/01

UK

TECHNICAL DATA COMPLIANT WITH KERAKOLL QUALITY STANDARD

Appearance part A coloured paste / part B straw-coloured liquid Specific weight part A ≈ 1,69 kg/dm3 / part B ≈ 0,99 kg/dm3 UEAtcViscosity 80200 mPa · sMineralogical nature of inert material silicate - crystalline (part A)Chemical nature epoxy resin (part A) / polyamines (part B)Grading ≈ 0 - 250 µmShelf life ≈ 24 months in the original packagingWarning Protect from frost, avoid direct exposure to sunlight and sources of heatPack part A bucket 2,82 kg / part B bottle 0,18 kgMixing ratio part A : part B = 2,82 : 0,18Specific weight of the mixture ≈ 1,55 kg/dm3

Pot life at +23°C ≥ 1 hrTemperature range for application from +5 °C to +30 °CJoints width colour collections:- Classic, Design and Colors from 0 to 20 mm- Crystal from 0 to 10 mmFoot traffic ≈ 12 hrsGrouting after laying:- with adhesive see characteristics of adhesive- mortar ≈ 7 – 14 daysInterval before normal use ≈ 3 days (mechanical resistance) / ≈ 4 days (chemical resist.)Coverage see Coverage tableValues taken at +23 °C, 50% R.H. and no ventilation. Data may vary depending on specific conditions at the building site, i.e.temperature, ventilation and absorbency level of the substrate and of the materials laid.

Fuga

lite®

Eco

Cod

e: P

779

2012

/01

UK

COVERAGE TABLE

Format Thicknessgrammes/m2 joint width

1 mm 2 mm 5 mm 10 mm

Mosaic 2x2 cm 3 mm ≈ 530 ≈ 1.060 ≈ 2.650 ≈ 5.300

5x5 cm 4 mm ≈ 290 ≈ 580 ≈ 1.450 ≈ 2.900

Tiles 30x60 cm 4 mm ≈ 40 ≈ 80 ≈ 200 ≈ 400

50x50 cm 4 mm ≈ 30 ≈ 60 ≈ 150 ≈ 300

60x60 cm 4 mm ≈ 25 ≈ 50 ≈ 125 ≈ 250

100x100 cm 4 mm ≈ 15 ≈ 30 ≈ 75 ≈ 150

20x20 cm 8 mm ≈ 150 ≈ 300 ≈ 750 ≈ 1.500

30x30 cm 9 mm ≈ 110 ≈ 220 ≈ 550 ≈ 1.100

40x40 cm 10 mm ≈ 90 ≈ 180 ≈ 450 ≈ 900

30x60 cm 10 mm ≈ 90 ≈ 180 ≈ 450 ≈ 900

60x60 cm 10 mm ≈ 60 ≈ 120 ≈ 300 ≈ 600

60x90 cm 10 mm ≈ 50 ≈ 100 ≈ 250 ≈ 500

100x100 cm 10 mm ≈ 35 ≈ 70 ≈ 175 ≈ 350

120x120 cm 10 mm ≈ 30 ≈ 60 ≈ 150 ≈ 300

20x20 cm 14 mm ≈ 260 ≈ 520 ≈ 1.300 ≈ 2.600

30x30 cm 14 mm ≈ 170 ≈ 340 ≈ 850 ≈ 1.700

Klinker 30x30 cm 15 mm ≈ 185 ≈ 370 ≈ 925 ≈ 1.850

12,5x24,5 cm 12 mm ≈ 270 ≈ 540 ≈ 1.350 ≈ 2.700

VOC INDOOR AIR QUALITY (IAQ) - VOLATILE ORGANIC COMPOUND EMISSIONSConformity EC 1 plus GEV-Emicode GEV certified 2476/11.01.02HIGH-TECHStatic modulus of elasticity 570 MPa ISO 178Resistance to abrasion 215 mm3 EN 12808-2Water absorption after 240 min. 0,04 g EN 12808-5Working temperature from -40 °C to +110 °CColour fastness according to UNI EN ISO 105-A05 see tableResistance to fungal contamination class F+ CSTB 2011-002Resistance to bacterial contamination class B+ CSTB 2010-083Porcelain tiles/concrete tensile strength ≥ 1,5 N/mm2 EN 1348Resistance to iodine stains class 4 ISO 10545-14Resistance to olive oil stains class 5 ISO 10545-14Resistance to chromium stains class 3 ISO 10545-14

Values taken at +23 °C, 50% R.H. and no ventilation. Data may vary depending on specific conditions at the building site.

PERFORMANCE

Legend rrr Excellentrr Goodr poor Values taken at: - ambient +23 °C / 50% R.H. - chemical aggressive agent +23 °C

CHEMICAL RESISTANCES (EN 12808-1)

Acids Concentration Permanent contact Occasional contact

Acetic 2,5% rr rrr

5% r rr

10% r r

Hydrochloric 37% rrr rrr

Citric 10% rr rrr

Formic 2,5% rr rrr

10% r r

Phosphoric 50% rrr rrr

75% r rr

Lactic 2,5% rr rrr

5% r rr

10% r r

Nitric 25% rr rrr

50% r r

Oleic 100% r r

Sulphuric 50% rrr rrr

100% r r

Tannic 10% rr rrr

Tartaric 10% rr rrr

Fuga

lite®

Eco

Cod

e: P

779

2012

/01

UK

Fuga

lite®

Eco

Cod

e: P

779

2012

/01

UK

CHEMICAL RESISTANCES (EN 12808-1)

Legend rrr Excellentrr Goodr poor Values taken at: - ambient +23 °C / 50% R.H. - chemical aggressive agent +23 °C

FoodstuffsMain foodstuffs

(temporary contact)

Vinegar rr

Citrus fruits rr

Ethyl alcohol rrr

Beer rrr

Butter rrr

Coffee rrr

Casein rrr

Glucose rrr

Animal fat rrr

Fresh milk rr

Malt rrr

Margarine rrr

Olive oil rr

Soya oil rr

Pectin rrr

Tomato rr

Yoghurt rr

Sugar rrr

Fuels and Oils Permanent contact Occasional contact

Petrol r rrr

Diesel oil rr rrr

Coal tar oil rr rr

Mineral oil rr rrr

Petroleum rr rrr

mineral spirit r rrr

Turpentine r rrr

Alkalis and Salts Concentration Permanent contact Occasional contact

Oxygenated water10% rr rrr

25% r rrr

Ammonia 25% rrr rrr

Calcium chloride Saturated Sol. rrr rrr

Sodium chloride Saturated Sol. rrr rrr

Sodium hypochlorite (Acti-ve chlorine)

0,63% rr rrr

13% r rr

Caustic soda 50% rrr rrr

Aluminium sulphate Saturated Sol. rrr rrr

Potassium hydroxide 50% rrr rrr

Potassium permanganate 5% rr rrr

10% r rr

Fuga

lite®

Eco

Cod

e: P

779

2012

/01

UK

CHEMICAL RESISTANCES (EN 12808-1)

Legend rrr Excellentrr Goodr poor Values taken at: - ambient +23 °C / 50% R.H. - chemical aggressive agent +23 °C

Solvents Permanent contact Occasional contact

Acetone r r

Ethyl alcohol rr rrr

Benzol r rr

Chloroform r r

Methylene chloride r r

Ethylene glycol rrr rrr

Perchloroethylene r rr

Carbon tetrachloride r rr

Tetrahydrofuran r r

Toluol r rr

Trichloroethylene r r

Xylene r rr

RESISTANCE TO STAINS (ISO 10545-14)

Legenda

Staining agents Time exposed to staining agent: 24 hours Time exposed to staining agent: 30 min.

Red wine 5 5Mineral oil 5 5Tomato ketchup 2 5Mascara 3 5Coffee 2 5Hair dye 1 2

5 can be cleaned under a running hot tap while gently rubbing with a sponge4 can be cleaned with a mild detergent while gently rubbing with a sponge.3 can be cleaned with a basic detergent while vigorously rubbing with a sponge2 to clean, treat first with a solvent or aggressive acid or basic solution, then vigorously rub with a sponge1 cannot be cleaned by any of the aforementioned methods.

The Eco and Bio classifications refer to the GreenBuilding Rating Manual 2011. This information was last updated in January 2012 (ref. GBR Data Report - 01.12); please note that additions and/or amendments may be made over time by KERAKOLL SpA; for the latest version, see www.kerakoll.com. KERAKOLL SpA shall therefore be liable for the validity, accuracy and updating of information provided only when taken directly from its institutional website. The technical data sheet given here is based on our technical and practical knowledge. As it is not possible for us to directly check the conditions in your building yards and the execution of the work, this information represents general indications that do not bind Kerakoll in any way. Therefore, it is advisable to perform a preliminary test to verify the suitability of the product for your purposes.

KERAKOLL UK LTD.Unit 4, The Croft, Buntsford Gate Business ParkBromsgrove, Worcestershire B60 4JE, United KingdomTel +44 01527 578000 - Fax +44 01527 578170info@kerakoll.co.uk - www.kerakoll.com

- Product for professional use- abide by any standards and national regulations- use at temperatures between +5 °C and +30 °C - use packs which have been stored for 2/3 days before use at +20 °C- respect the mixing ratio of 2.82 : 0.18. For partial mixing, weigh the two parts precisely - workability times may vary considerably, depending on ambient conditions and the temperature of the tiles - do not walk on floors that are still damp as dirt could still stick to them- do not lay on substrates subject to moisture rising or which are not completely dry- if necessary, ask for the safety data sheet- for any other issues, contact the Kerakoll Worldwide Global Service - globalservice@kerakoll.com

WARNINGFu

galit

e® E

co C

ode:

P77

9 20

12/0

1 UK

COLOUR CHART

from 5 to 4 high colour fastness; for internal and external usefrom 3.5 to 3 good colour fastness; for internal and external usefrom 2.5 to 1 limited colour fastness; for internal use

Legend

Fugalite® Eco colours Colour Fastness* GSc (Daylight) EN ISO 105-A05 standard

Clas

sic

01 White 1,5

02 Light Grey 1

03 Pearl Grey 1

04 Iron Grey 1,5

05 Anthracite 2

06 Black 2,5

07 Jasmin 1

08 Bahama Beige 1

09 Caramel 1,5

10 Terracotta 2

11 Brown 2,5

12 Walnut 2,5

Desi

gn

51 Silver 1,5

50 Pergamon 1,5

46 Ivory 1

45 Limestone 1

52 Dove Grey 1,5

44 Cement Grey 1

48 Coffee 2,5

Colo

rs

38 Husky 1

47 Mediterranean 1

15 Ocean 1

41 Eucalyptus 1,5

49 Moss 2

20 Magnolia 1,5

27 Sunset 1,5

21 Red 4

23 Yellow 1

Crys

tal

Extra-fine white 1

Neutral 1

Tested and GEV certified with very low-VOC emissions

REVOLUTIONARY,

PHOTOCHROMATIC,

WATER-REPELLENT

The photochromatic, waterproof grout and

adhesive that enhances the beauty of glass mosaic.

Fugalite® Eco Invisibile

LIQUID GLASS FOR PERFECT JOINTS

INNOVATIVE®

eco SAFE

INVISIBLE

CERTIFIED, ECO-FRIENDLY, PHOTOCHROMATIC VITREOUS, HIGH-SLIDE, EASY-TO-CLEAN GROUT AND ADHESIVE, BACTERIOSTATIC AND FUNGISTATIC, WATER AND STAIN PROOF, FOR JOINTS OF BETWEEN 0 AND 3 MM, TO GUARANTEE THE APPEARANCE, FUNCTIONALITY AND HYGIENE OF GLASS MOSAIC AND CERAMIC SURFACES, IDEAL FOR USE IN GREENBUILDING. WITH VERY LOW VOLATILE ORGANIC COMPOUND EMISSIONS.

REVOLUTIONARY

The opalescent, semi-transparent appearance of Fugalite® Eco Invisibile grout has been tested by the GreenLab laboratories to guarantee maximum aesthetic compatibility with wood and marble effect tiles.Fugalite® Eco Invisibile makes the joint “invisible”, guaranteeing a surface with an even colour and appearance, something that cannot be achieved with any other coloured opaque cement-based grout.

Fugalite® Eco Invisibile is liquid “glass” obtained from a perfectly calibrated mixture of tiny, pure glass beads and an exclusive transparent resin, ideal as an adhesive for laying and grouting of glass mosaic. The excellent workability and cleanability of Fugalite® Eco Invisibile during the application phase ensure a perfect, smooth, even grout that enhances ceramic and glass mosaic surfaces.

Fugalite® Eco Invisibile LIQUID GLASS FOR PERFECT JOINTS

Scanning electron microscope view of the glass beads

Ideal for wood and ceramic marble laid edge-to-edge

PURE TRANSPARENT

RESIN

PU

RESIN

SEMI-TRANSPARENT EFFECTSEMI-TRANSPARENT EFFECT

REAL GLASS BEADS SEMI-TRANSPARENT

JOINTS DISAPPEAR

SEMI-TRANSPARENT

JOINTS DISAPPEAR

INNOVATIVE PHOTOCHROMATICCLEAN WATER-RESISTANT

WATER-RESISTANTCLEAN AND SAFE

Fugalite® Eco Invisibile: intelligent laying and grouting of glass mosaic

CO

NTRIBUTES TO

P O I N T S

Patent PendingIN

TERN

ATIONAL PATENT

A

PPLIC ATIO

N

*

KERA

KOLL MONOPACK

AB

S Y S T E M

PHOTOCHROMATIC

Just like glass, Fugalite® Eco Invisibile is waterproof, easy to wash and keep clean. Makes the surface safe from bacteria, mould and fungi even in very damp environments. Strong and easy to maintain, it ensures long-term durability while retaining the aesthetic quality and beauty of the mosaics and coverings.Fugalite® Eco Invisibile is designed to improve people’s health and well-being.

Light as a pigment that colours the grout. This is the challenge won by the Kerakoll® researchers, making Fugalite® Eco Invisibile unique and inimitable. An idea that is simple and effective, but hard to achieve, and is only made possible thanks to a perfect balance of high quality ingredients. The shades of colour in the blends of glass mosaic grouted using Fugalite® Eco Invisibile will be perfect. Inserts, decorations, shapes will no longer be a problem.

* Centro Ceramico Bologna has passed the test for Resistance to stains following UNI EN ISO 10545-14 (Test Report N° 3 685/11).

* ÉMISSION DANS L’AIR INTÉRIEUR Information sur le niveau d’émission de substances volatiles dans l’air intérieur, présentant un risque de toxicité par inhalation, sur une échelle de classe allant de A+ (très faibles émissions) à C (fortes émissions).

1

®

Fugalite® Eco Invisibile is the ideal solution for the safe and long-lasting laying of glass mosaics, guaranteeing perfect diffusion of colour shades and an unparalleled aesthetic continuity.

Diffusion and diffraction of light “colours” the grout

The smooth, waterproof surface of the grout makes the joints safer and easier to keep clean

DIFFUSES THE COLOURS

OF THE TILED SURFACE

Fugalite® Eco Invisibile Cement-based grout

NATURAL LIGHT COLOURS JOIN TOGETHER

MORE HYGIENIC

Fugalite® Eco Invisibile Cement-based Grout

DIFFUSES THE COLOURS

OF THE TILED SURFACE

KERAKOLL Spavia dell’Artigianato, 9 - 41049 Sassuolo (MO) Italia

Tel +39 0536 816 511 - Fax +39 0536 816 581e-mail: info@kerakoll.com www.kerakoll.com

MKT

-TEC

cod

e 34

/201

3 A

Ref.

GBR

Data

Rep

ort 0

5.13

Fugalite® Eco InvisibileCOMPARISON WITH CEMENT-BASED GROUT

SEMI-TRANSPARENT

PHOTOCHROMATIC

WATER-RESISTANT

Fuga-Glitter

Easy to clean

Enhances mosaic

Joints disappear

Fuga-Glitter in Gold and Silver colours emphasizes the shade and detail of the covering by creating a constant play on the reflections of the glitter. Fuga-Glitter is a bright, ultra-fine powder that can be easily added to Fugalite® Eco Invisibile in the proportions required to create the desired effect.

Fugalite® Eco Invisibile Cement-based grout

Fugalite® Eco Invisibile Cement-based grout

Fugalite® Eco Invisibile Cement-based grout

KERAKOLL S.p.a.Via dell’Artigianato, 9 - 41049 Sassuolo (MO) Italy Tel +39 0536 816 511 - Fax +39 0536 816 581info@kerakoll.com - www.kerakoll.com

This information was last updated in December 2013; please note that additions and/or amendments may be made over time by KERAKOLL SpA; for the latest version, see www.kerakoll.com. KERAKOLL SpA shall therefore be liable for the validity, accuracy and updating of information provided only when taken directly from its institutional website. The technical data sheet given here is based on our technical and practical knowledge. As it is not possible for us to directly check the conditions in your building yards and the execution of the work, this information represents general indications that do not bind Kerakoll in any way. Therefore, it is advisable to perform a preliminary test to verify the suitability of the product for your purposes.

0014

6Fug

a Gl

itter

Cod

e: P

781

2014

/02

EN

LAYING RANGE / Organic mineral grouts for ceramic tiles and natural stone

Glitter for Fugalite® Eco and Fugalite® Eco Invisibile.

Specific glitter to be used as an additive and metalized decoration of Fugalite® Eco and Fugalite® Eco Invisibile.

Fuga-Glitter

• Dissolves easily

• Permanent shine

• Excellent chemical resistance

PRODUCT STRENGTHS

UseAdditive for Fugalite® Eco and Fugalite® Eco Invisibile to give the metalized effect.

AREAS OF USE

ApplicationMix Fugalite® Eco / Fugalite® Eco Invisibile Part A with Fugalite® Eco / Fugalite® Eco Invisibile Part B until a smooth mixture forms.Add Fuga-Glitter Gold or Silver in the recommended amounts (approx. 100 – 300 grammes for every pack of Fugalite® Eco/ Fugalite® Eco Invisibile according to the aesthetic finish required).Mix together manually using a trowel before mixing more smoothly from the bottom upwards with a low-rev (≈ 400/min.) helicoidal agi-tator, to prevent dispersion into the air.When an smooth mixture has been obtained, apply Fugalite® Eco / Fugalite® Eco Invisibile with additives and proceed with the usual finishing and cleaning operations. Apply the mixed product to a trial section to check the aesthetic effect.

INSTRUCTIONS FOR USE

- Product for professional use- abide by any standards and national regulations- fine-grain, lightweight product: take care not to allow it to disperse into the air when mixing- for any other issues, contact the Kerakoll Worldwide Global Service +39 0536 811 516 - globalservice@kerakoll.com

WARNING

Recommended dosage 100 – 300 g / 1 package Fugalite® Eco – Fugalite® Eco InvisibileNature polyesterShape hexagonal prismDimensions ≈ 0,2 mmSpecific weight ≈ 1,38 kg/dm3

Colour silver - goldChemical resistance Grade II

TECHNICAL DATA COMPLIANT WITH KERAKOLL QUALITY STANDARD

• Floors, for internal and external use

• Suitable for porcelain and ceramic tiles

• High chemical and mechanical resistances

• Ideal for industrial environments

• Water-resistant

RATING SYSTEM ACCREDITED BY CERTIFICATION BODY SGS

GREENBUILDING RATING® PRODUCT STRENGTHS

0035

6Fug

abel

la®

Eco

Pro

fess

iona

l Cod

e: P

584

2014

/06

- EN

LAYING RANGE / Organic mineral grouts for ceramic tiles and natural stone

CO

MPLIANT WITH

EUROPEAN NORM

RGEN 13888

CO

NTRIBUTES TO

P O I N T S

Eco-friendly, epoxy, organic mineral grout for joints with a high level of fluidity and mechanical, chemical and water resistance, for thicknesses of 2 mm to 15 mm, ideal for use in GreenBuilding. Safeguards the health of operators.

Fugabella® Eco Professional develops with low rheology meaning it can be applied quickly to large surfaces such as commercial and industrial floors which can then be easily cleaned, leaving no greasy film.

Fugabella® Eco Professional

Regional Mineral ≥

30

% IAQVOCIndoor Air Qualit

y

Low Emission

Solvent ≤ 5 g/kg

SLVREDUCED

Low Ecological Im

pact

Health Care

Natural mine-ral content

75%Non-toxic and non-hazardous

UseWater-resistant grouting of joints from 2 to 15 mm with high chemical and mechanical resistance and a high level of hardness.

Materials to be grouted:- porcelain tiles, ceramic tiles, klinker and ceramic mosaic of all types and formats

Internal and external flooring in domestic, commercial and industrial applications and street furniture subject to permanent or occa-sional contact with chemical substances, in environments subject to heavy traffic, also in areas prone to thermal shock and freezing.

Do not useOn joints less than 2 mm and more than 15 mm in width, on porous flooring for which more specific or alternative chemical resistan-ces are required compared with those listed in the chemical resistances table, to grout elastic expansion or fractionizing joints or on substrates that are not fully dry and subject to moisture rising.

AREAS OF USE

2

®

Preparation of substratesBefore grouting joints, check that tiles have been laid correctly and are anchored perfectly to the substrate. Substrates must be per-fectly dry. Grout joints in accordance with the recommended waiting time indicated on the relative data sheet for the adhesive used. For mortar substrates, wait at least 7 – 14 days depending on screed thickness, ambient weather conditions and on the level of absorption of the covering and the substrate. Any water or moisture rising can cause vapour pressure to accumulate, which may in turn loosen the tiles on account of the complete non-absorbency of the grout or of the tiles themselves.Joints must be free from any excess adhesive, even if already hardened. Furthermore they must be of an even depth for the whole width of the tile covering, thereby ensuring maximum chemical resistance.Any dust and loose debris must be removed from the joints by carefully cleaning them with a vacuum cleaner.Before grouting joints, check the cleanability of the tile covering, as porous or highly micro-porous surfaces may make cleaning difficult. It is advisable to perform a preliminary test on tiles not to be laid or in a small, concealed area. In these cases we recommend treating the covering with specific protective products, being careful to avoid applying them to the joints.

PreparationFugabella® Eco Professional is prepared by mixing together parts A and B from the bottom upwards, using a low-rev (≈ 400/min) heli-coidal agitator, respecting the preset ratio of 7.95 : 0.55 of the packs. Pour part B into the bucket containing part A, being careful to mix the two parts uniformly until a smooth, even coloured mixture is obtained. Only mix an amount of grout that can be used within 1 hour at +23 ºC, 50% R.H. Fugabella® Eco Professional product buckets must be stored at a temperature of approx. +20 °C for at least 2-3 days before use. Higher temperatures make the mixture too fluid and shorten hardening times, while lower temperatures make the mixture harder to spread and slow down setting times. At temperatures of less than +10 °C, the product will no longer set.

INSTRUCTIONS FOR USE

ApplicationFugabella® Eco Professional must be applied evenly on the tile covering with a hard rubber spreader. Seal the joints by completely grouting them, applying the grout diagonally to the tiles. Remove most of the excess grout immediately using the spreader, leaving only a thin film on the tile.

Cleaning Right after this, start to clean up the tile surface. On completion, clean the surface using a rigid, thick, large-sized sponge damped in clean water to avoid removing grout from the joints. Use circular movements to soften the film of grout on the tiles and finish cleaning the joint surface. Specific high-dispersion polymers ensure all grout residues are removed using only a small amount of water. The use of an excessive amount of water when cleaning would impair the final chemical resistances. it is important to rinse frequently and make sure clean water is used at all times, using appropriate trays and grills with cleaning rollers. If necessary, replace the sponge or felt cleaning pad when saturated with grout. Finish cleaning up by dragging the sponge diagonally across the tiles to avoid going into the joints. Wipe the cleaned surface again with a dry cloth to make sure it is completely clean and there are no streaks of resin remaining. Any remaining grout streaks can be removed before they harden with a 10/20% water-alcohol solution.Residual traces of grout can be removed from tools with water before the product has hardened.

INSTRUCTIONS FOR USE

Fugabella® Eco Professional can be used on walls to grout joints of between 2 and 5 mm.

When using Fugabella® Eco Professional to grout joints in large surface areas, use suitable electrical equipment to increase application speed and cleaning times. In particular, a mechanical buffer with hard felt disk will make cleaning easier and faster, ensuring a perfect finish at the same time.

Residual traces of hardened grout on non-absorbent tile coverings can be removed by applying the eco-friendly solvent gel Keragel Eco, following the instructions for use.

Fugabella® Eco Professional has a lower elastic modulus than cementitious grouts with added elastomeric latex or than Fugabella® Eco Flex. As a result, elastic, fractionizing and expansion joints can be created in smaller tilework coverings.

SPECIAL NOTES

High chemical and mechanical resistance grouting of ceramic and porcelain tiles, marble and natural stone is carried out using eco-friendly, epoxy, organic mineral grout with a high level of fluidity and water resistance, for joint thicknesses of 2 mm to 15 mm compliant with EN 13888 - class RG, GreenBuilding Rating® Eco 2, such as Fugabella® Eco Professional by Kerakoll Spa. Joints must be dry and free from traces of adhesive and loose debris. Use a spreader or hard rubber float to apply the grout and suitable sponges and clean water to clean joints on completion. Joints of ____ mm width and tiles ____ x ____ cm in size will give an average coverage of approx. ____ kg/m2. Existing elastic expansion and fractionizing joints must be respected.

ABSTRACT

0035

6Fug

abel

la®

Eco

Pro

fess

iona

l Cod

e: P

584

2014

/06

- EN

Appearance part A coloured paste / part B straw-coloured liquidSpecific weight part A ≈ 1.78 kg/dm3 / part B ≈ 1.00 kg/dm3 UEAtcMineralogical nature of inert material silicate - crystalline (part A)Chemical nature epoxy resinGrading ≈ 0 – 800 µmShelf life ≈ 12 months in the original packagingWarning protect from frost and avoid direct exposure to sunlight and sources of heatPack part A: 7.95 kg bucket / part B: 0.55 kg bottleMixing ratio part A : part B = 7.95 : 0.55Specific weight of the mixture ≈ 1,52 kg/dm3

Viscosity ≈ 250,000 mPa · s, rotor 93 RPM 4 Brookfield methodPot life at +23°C ≥ 1 hrTemperature range for application from +10 °C to +30 °CWidth of joints from 2 to 15 mmFoot traffic ≈ 24 hrsGrouting after laying:- with adhesive see characteristics of adhesive- mortar ≈ 7 – 14 daysInterval before normal use ≈ 3 days mechanical resistance / ≈ 4 days chemical resistanceCoverage see Coverage tableValues taken at +23 °C, 50% R.H. and no ventilation. Data may vary depending on specific conditions at the building site, i.e.temperature, ventilation and absorbency level of the substrate and of the materials laid.

TECHNICAL DATA COMPLIANT WITH KERAKOLL QUALITY STANDARD

COVERAGE TABLE

Format Thicknessgrammes/m2 joint width

1 mm 2 mm 5 mm 10 mm

TilesMarble

30x60 cm 4 mm ≈ 35 ≈ 70 ≈ 175 ≈ 350

60x60 cm 4 mm ≈ 25 ≈ 50 ≈ 125 ≈ 250

20x20 cm 8 mm ≈ 145 ≈ 290 ≈ 725 ≈ 1450

30x30 cm 9 mm ≈ 110 ≈ 220 ≈ 550 ≈ 1100

40x40 cm 10 mm ≈ 90 ≈ 180 ≈ 450 ≈ 900

30x60 cm 10 mm ≈ 95 ≈ 170 ≈ 475 ≈ 950

60x60 cm 10 mm ≈ 65 ≈ 130 ≈ 325 ≈ 650

20x20 cm 14 mm ≈ 255 ≈ 510 ≈ 1275 ≈ 2550

30x30 cm 14 mm ≈ 170 ≈ 340 ≈ 850 ≈ 1700

Klinker 12,5x24,5 cm 12 mm ≈ 265 ≈ 530 ≈ 1325 ≈ 2650

HIGH-TECHStatic modulus of elasticity ≤ 1050 N/mm2 ISO 178Flexural strength after 28 days ≥ 30 N/mm2 EN 12808-3Compressive strength after 28 days ≥ 45 N/mm2 EN 12808-3Resistance to abrasion ≤ 200 mm3 EN 12808-2Water absorption after 240 min. ≤ 0,1 g EN 12808-5Chemical resistance see chemical resistance tableWorking temperature from -40 °C to +110 °CConformity RG EN 13888

Values taken at +23 °C, 50% R.H. and no ventilation. Data may vary depending on specific conditions at the building site.

PERFORMANCE

0035

6Fug

abel

la®

Eco

Pro

fess

iona

l Cod

e: P

584

2014

/06

- EN

Values taken at: - ambient +23 °C / 50% R.H. - chemical aggressive agent +23 °C

CHEMICAL RESISTANCE

Legend ••• Excellent•• Good• poor

Acids Concentration Permanent contact Occasional contact

Acetic

2,5% ••• •••

5% •• •••

10% • •

Hydrochloric 37% ••• •••

Citric 10% •• •••

Formic2,5% ••• •••

10% • •

Phosphoric50% ••• •••

75% • ••

Lactic

2,5% ••• •••

5% •• •••

10% • ••

Nitric25% •• •••

50% • •

Oleic 100% • •

Sulphuric50% ••• •••

100% • •

Tannic 10% ••• •••

Tartaric 10% ••• •••

Foodstuffs Main foodstuffs (temporary contact)

Vinegar •••

Citrus fruits •••

Ethyl alcohol •••

Beer •••

Butter ••

Coffee •••

Casein •••

Chlorine ••

Glucose ••

Animal fat ••

Fresh milk •••

Malt •••

Margarine ••

Olive oil •••

Soya oil ••

Pectin •••

Tomato ••

Yoghurt ••

Sugar •••

Fuels and Oils Permanent contact Occasional contact

Petrol ••• •••

Diesel oil ••• •••

Coal tar oil •• ••

Mineral oil ••• •••

Petroleum ••• •••

mineral spirit ••• •••

Turpentine ••• •••

0035

6Fug

abel

la®

Eco

Pro

fess

iona

l Cod

e: P

584

2014

/06

- EN

The Eco and Bio classifications refer to the GreenBuilding Rating® Manual 2013. This information was last updated in May 2014 (ref. GBR Data Report - 06.14); please note that additions and/or amendments may be made over time by KERAKOLL SpA; for the latest version, see www.kerakoll.com. KERAKOLL SpA shall therefore be liable for the validity, accuracy and updating of information provided only when taken directly from its institutional website. The technical data sheet given here is based on our technical and practical knowledge. As it is not possible for us to directly check the conditions in your building yards and the execution of the work, this information represents general indications that do not bind Kerakoll in any way. Therefore, it is advisable to perform a preliminary test to verify the suitability of the product for your purposes.

KERAKOLL S.p.a.Via dell’Artigianato, 9 - 41049 Sassuolo (MO) Italy Tel +39 0536 816 511 - Fax +39 0536 816 581info@kerakoll.com - www.kerakoll.com

ISO 9001CERTIFIEDIT10/0327

ISO 14001CERTIFIED

IT242729/UK

BS 18001CERTIFIED

IT255412/UK

Values taken at: - ambient +23 °C / 50% R.H. - chemical aggressive agent +23 °C

CHEMICAL RESISTANCE

Legend ••• Excellent•• Good• poor

Alkalis and Salts Concentration Permanent contact Occasional contact

Oxygenated water10% ••• •••

25% •• •••

Ammonia 25% ••• •••

Calcium chloride Saturated Sol. ••• •••

Sodium chloride Saturated Sol. ••• •••

Sodium hypochlorite(Active chlorine)

0,63% •• •••

13% • •

Caustic soda 50% ••• •••

Aluminium sulphate Saturated Sol. ••• •••

Potassium hydroxide 50% ••• •••

Potassium permanganate 5% •• •••

10% • ••

Solvents Permanent contact Occasional contact

Acetone • •

Ethyl alcohol •• •••

Benzol • ••

Chloroform • •

Methylene chloride • •

Ethylene glycol ••• •••

Perchloroethylene • ••

Carbon tetrachloride • ••

Tetrahydrofuran • •

Toluol • ••

Trichloroethylene • •

Xylene • •

COLOUR CHARTFugabella® Eco Professional colours

03 Pearl Grey

04 Iron Grey

08 Bahama Beige

- Product for professional use- abide by any standards and national regulations- use at temperatures between +10 °C and +30 °C- use packs which have been stored for 2/3 days before use at +20 °C- respect the mixing ratio of 7.95 : 0.55. For partial mixing, weigh the two parts precisely- workability times may vary considerably, depending on ambient conditions and the temperature of the tiles- protect the grout from direct rainfall and sun for at least 12 hours after application- do not lay on substrates subject to moisture rising or which are not completely dry- if necessary, ask for the safety data sheet- for any other issues, contact the Kerakoll Worldwide Global Service +39 0536 811 516 - globalservice@kerakoll.com

WARNING

0035

6Fug

abel

la®

Eco

Pro

fess

iona

l Cod

e: P

584

2014

/06

- EN

RATING SYSTEM ACCREDITED BY CERTIFICATION BODY SGS

GREENBUILDING RATING®

LAYING RANGE / Organic mineral grouts for ceramic tiles and natural stone

0074

9 Fu

ga-W

ash

Eco

Code

: P87

8 20

14/0

1 EN

CO

NTRIBUTES TO

P O I N T S

Eco-friendly detergent to be used as an additive in water used to clean Fugalite® Eco, Fugalite® Eco Invisibile and Fugalite® Zero, ideal for use GreenBuilding. Water-based concentrate, solvent-free, safeguards the health of both operators and the environment.

Fuga-Wash Eco, when used as an additive in cleaning water, has a specific detergent action that does not damage ceramic tile, porcelain tile and natural stone surfaces.

Fuga-Wash Eco

4

®IAQ

VOCIndoor Air Quality

Low Emission

Water Based

Solvent ≤ 80 g/kg

SLVREDUCED

Low Ecologica l Im

pact

Health Care

Water-based formulation Solvent-free

No environmental hazard rating

Non-toxic and non-hazardous

• Facilitates cleaning of covering materials

• Keeps the sponge cleaner

• Cleans thoroughly, no need to rinse

• Improves the surface finish of the grout

• Suitable for all surfaces

PRODUCT STRENGTHS

UseTo be added to the water used to clean Fugalite® Eco, Fugalite® Eco Invisibile and Fugalite® Zero.

Substrates:- ceramic and homogeneous tiles- glass mosaic, marble and natural stone

Do not useTo remove residues and streaks of hardened grout.

AREAS OF USE

Preparation of substratesThe coating materials must first be cleaned to remove any dust. Fugalite® Eco, Fugalite® Eco Invisibile and Fugalite® Zero must still be fresh.

PreparationFuga-Wash Eco is a ready-to-use transparent fluid that can be diluted with water in any ratio. Shake the bottle well before opening in order to redisperse the liquid evenly. Pour one measuring cap (approx. 50 ml) for every 5 litres of water in the cleaning tray.

ApplicationBegin cleaning the tilework when the grout is still fresh. On completion, pour Fuga-Wash Eco into the cleaning tray in the quantities indicated, then clean up the surface using a thick, large-sized damp sponge, preferably made of cellulose, to avoid removing grout from the joints. Use circular movements to soften the film of grout on the tiles and finish cleaning the joint surface. Specific high-dispersion polymers ensure all grout residues are removed using only a small amount of water. The use of an excessive amount of water when cleaning would impair the final chemical resistances. Rinse frequently and make sure clean water is used at all times, using appropriate trays and grills with cleaning rollers. If necessary, replace the sponge or felt cleaning pad when saturated with grout. Finish cleaning up by dragging the sponge diagonally across the tiles to avoid going into the joints. Wipe the cleaned surface again with a dry cloth to make sure it is completely clean and there are no streaks of resin remaining.

CleaningResidues of Fuga-Wash Eco can be cleaned from tools by rinsing them thoroughly.

INSTRUCTIONS FOR USE

KERAKOLL S.p.a.Via dell’Artigianato, 9 - 41049 Sassuolo (MO) Italy Tel +39 0536 816 511 - Fax +39 0536 816 581info@kerakoll.com - www.kerakoll.com

The Eco and Bio classifications refer to the GreenBuilding Rating® Manual 2013. This information was last updated in Decembre 2013 (ref. GBR Data Report - 01.14); please note that additions and/or amendments to this information may be made over time by KERAKOLL Spa; for the latest version, see www.kerakoll.com. KERAKOLL SpA shall therefore be liable for the validity, accuracy and updating of information provided only when taken directly from its institutional website. The technical data sheet given here is based on our technical and practical knowledge. As it is not possible for us to directly check the conditions in your building yards and the execution of the work, this information represents general indications that do not bind Kerakoll in any way. Therefore, it is advisable to perform a preliminary test to verify the suitability of the product for your purposes.

0074

9 Fu

ga-W

ash

Eco

Code

: P87

8 20

14/0

1 EN

To be added to the water used to clean Fugalite® Eco, Fugalite® Eco Invisibile and Fugalite® Zero, from ceramic tiles, porcelain tiles, glass mosaic, marble and natural stone use an eco-friendly, water-based detergent, Eco 4 GreenBuilding Rating®, such as Fuga-Wash Eco by Kerakoll Spa.

ABSTRACT

- Product for professional use- abide by any standards and national regulations- store and use at a temperature above +5 °C. Protect from frost- do not leave cans or bottles open, even during use- if necessary, ask for the safety data sheet- for any other issues, contact the Kerakoll Worldwide Global Service +39 0536 811 516 - globalservice@kerakoll.com

WARNING

Appearance Transparent liquidSpecific weight ≈ 1 kg/dm3

Shelf life ≈ 24 months in the original packagingWarning Protect from frost, avoid direct exposure to sunlight and sources of heatPack bottles 1.5 ℓWater dilution ratios All ratios recommended dosage 1 measuring cap every 5 ℓ of water in the washing traypH ≈ 7Temperature range for application from +5 °C to +35 °CCoverage ≈ 100 – 200 m2/1 ℓValues taken at +23 °C, 50% R.H. and no ventilation. Data may vary depending on specific conditions at the building site, i.e.temperature, ventilation and absorbency level of the substrate and of the materials laid.

TECHNICAL DATA COMPLIANT WITH KERAKOLL QUALITY STANDARD

LAYING RANGE / Organic Mineral Grouts for Ceramic Tiles and Natural Stone

UseTo eliminate residues and streaks of Fugalite® Eco and Fugalite® Eco Invisibile from ceramic surfaces.

Substrates:- ceramic and homogeneous tiles- glass mosaic, marble and natural stone

Do not useOn surfaces that are not resistant to basic agents.

AREAS OF USE

0013

1 Fu

ga-S

oap

Eco

Code

: P78

1 20

13/0

5 UK

CO

NTRIBUTES TO

P O I N T S

Eco-friendly detergent to remove residues and streaks of Fugalite® Eco and Fugalite® Eco Invisibile, ideal for use GreenBuilding. Water-based concentrate, safeguards the health of both operators and the environment.

Fuga-Soap Eco is an effective and specific detergent for use in cleaning after laying as it can be used in the routine maintenance of ceramic tiles, porcelain tiles and natural stone.

Fuga-Soap Eco

PRODUCT STRENGTHS

• Flooring and walls

• Can be diluted in water in any ratio

• Suitable for use with compact and porous materials

• Suitable for delicate marbles

• Ideal for internal environments

GREENBUILDING RATING®

3

®IAQ

VOCIndoor Air Quality

Low Emission

Water Based

Solvent ≤ 80 g/kg

SLVREDUCED

Low Ecologica l Im

pact

Health Care

Water-based formulation

No environmental hazard rating

Non-toxic and non-hazardous

RATING SYSTEM ACCREDITED BY CERTIFICATION BODY SGS

Preparation of substrates The coating materials must first be cleaned to remove any dust. Fugalite® Eco and Fugalite® Eco Invisibile must be fully hardened.

PreparationFuga-Soap Eco is a ready-to-use yellowish liquid, water-dilutable in any ratio depending on the type of dirt to be removed. Shake the bottle well before opening in order to redisperse the liquid evenly.

ApplicationIt is advisable to perform a preliminary test on tiles that are not to be laid, or in a concealed area. Apply Fuga-Soap Eco evenly to the surface to be cleaned and leave it until the dirt to be removed begins to visibly lift; this may take a few minutes or up to 10-30 minutes depending on the quantity, the elapsed time after laying (at least 24 hours) and the degree of absorption of the substrate. Scrape the surface mechanically with abrasive felt pads. Once cleaned, rinse well and dry carefully. The use of wet vacuum makes the operation easier and ensures the complete removal of residue. In the case of large surface areas, a mechanical buffer with an abrasive felt pad for the removing operation is recommended. Repeat for highly stubborn dirt.

CleaningResidues of Fuga-Soap Eco can be cleaned from tools by rinsing them thoroughly with water.

INSTRUCTIONS FOR USE

The Eco and Bio classifications refer to the GreenBuilding Rating® Manual 2013. This information was last updated in April 2013 (ref. GBR Data Report - 05.13); please note that additions and/or amendments may be made over time by KERAKOLL SpA; for the latest version, see www.kerakoll.com. KERAKOLL SpA shall therefore be liable for the validity, accuracy and updating of information provided only when taken directly from its institutional website. The technical data sheet given here is based on our technical and practical knowledge. As it is not possible for us to directly check the conditions in your building yards and the execution of the work, this information represents general indications that do not bind Kerakoll in any way. Therefore, it is advisable to perform a preliminary test to verify the suitability of the product for your purposes.

KERAKOLL UK Ltd.Unit 4, The Croft, Buntsford Gate Business ParkBromsgrove, Worcestershire B60 4JE, United KingdomTel +44 01527 578000 - Fax +44 01527 578170info@kerakoll.co.uk - www.kerakoll.com

Appearance yellowish liquidSpecific weight ≈ 1,01 kg/dm3

Shelf life ≈ 24 months in the original packagingWarning Protect from frost, avoid direct exposure to sunlight and sources of heatPack bottles 1 lWater dilution ratios All ratiosViscosity ≈ 211 mPa · s, rotor 2 RPM 50 Brookfield methodpH ≈ 12,5Temperature range for application from +5 °C to +35 °CWaiting time before cleaning with water ≈ 10 – 30 min.Coverage ≈ 10 – 20 m2/1 lValues taken at +23 °C, 50% R.H. and no ventilation. Data may vary depending on specific conditions at the building site, i.e.temperature, ventilation and absorbency level of the substrate and of the materials laid.

TECHNICAL DATA COMPLIANT WITH KERAKOLL QUALITY STANDARD

- Product for professional use- abide by any standards and national regulations- store and use at a temperature above +5 °C. Protect from frost- rinse thoroughly all surfaces treated- do not leave cans or bottles open, even during use- if necessary, ask for the safety data sheet- for any other issues, contact the Kerakoll Worldwide Global Service - globalservice@kerakoll.com

WARNING

Fuga-Soap Eco is a liquid detergent. Before using the product, it is advisable to hermetically seal all doors, windows, rubber seals, furniture, varnished/painted elements, bathtubs and shower trays made of synthetic materials such as methacrylate, PVC, etc..and any surface that could be attacked through direct contact with the detergent or with vapours.

SPECIAL NOTES

0013

1 Fu

ga-S

oap

Eco

Code

: P78

1 20

13/0

5 UK

RATING SYSTEM ACCREDITED BY CERTIFICATION BODY SGS

GREENBUILDING RATING®

LAYING RANGE / Organic mineral grouts for ceramic tiles and natural stone

0080

0 Fu

ga-S

hock

Eco

Cod

e: P

965

2015

/11

UK

CO

NTRIBUTES TO

P O I N T S

Eco-friendly cleaner, ready to use, for removing residues and streaks of epoxy resins, ideal for use in Greenbuilding.

Fuga-Shock Eco has a specific cleaning action that removes residues and streaks from ceramic tile, porcelain tile and glass mosaic surfaces.

Fuga-Shock Eco

3

®IAQ

VOCIndoor Air Quality

Low Emission

Water Based

Solvent ≤ 80 g/kg

SLVREDUCED

Low Ecologica l Im

pact

Health Care

Water-based formulation

No environmental hazard rating

Non-toxic and non-hazardous

• Floors and walls

• Suitable for use with compact and porous materials

• Highly effective

PRODUCT STRENGTHS

UseTo eliminate residues and streaks of Fugalite® from ceramic surfaces.

Substrates:- ceramic and homogeneous tiles- glass mosaic

Do not useOn surfaces that are not resistant to basic agents. On marble and natural stone it is advisable to carry out a test in advance.

AREAS OF USE

Preparation of substratesThe coating materials must first be cleaned to remove any dust. Fugalite® must be fully hardened.

PreparationFuga-Shock Eco is a ready-to-use transparent liquid. Shake the bottle well before opening in order to redisperse the liquid evenly.

ApplicationIt is advisable to perform a preliminary test on tiles that are not to be laid, or in a concealed area. Apply Fuga-Shock Eco evenly to the surface to be cleaned with a white rough scrubbing pad and leave it until the dirt to be removed begins to visibly lift; this may take a few minutes or up to 3 – 5 minutes depending on the quantity, the elapsed time after laying (at least 7 days) and the degree of absorption of the surface. Scrape the surface mechanically with abrasive felt pads. Once cleaned, rinse well and dry carefully. The use of wet vacuum makes the operation easier and ensures the complete removal of residue. In the case of large surface areas, a mechanical buffer with an abrasive felt pad for the removing operation is recommended. Repeat for highly stubborn dirt.

CleaningResidues of Fuga-Shock Eco can be cleaned from tools by rinsing them thoroughly with water.

INSTRUCTIONS FOR USE

The Eco and Bio classifications refer to the GreenBuilding Rating® Manual 2012. This information was last updated in April 2015 (ref. GBR Data Report - 05.15); please note that additions and/or amendments may be made over time by KERAKOLL SpA; for the latest version, see www.kerakoll.com. KERAKOLL SpA shall therefore be liable for the validity, accuracy and updating of information provided only when taken directly from its institutional website. The technical data sheet given here is based on our technical and practical knowledge. As it is not possible for us to directly check the conditions in your building yards and the execution of the work, this information represents general indications that do not bind Kerakoll in any way. Therefore, it is advisable to perform a preliminary test to verify the suitability of the product for your purposes.

KERAKOLL UK Ltd.Unit 4, The Croft, Buntsford Gate Business ParkBromsgrove, Worcestershire B60 4JE, United KingdomTel +44 01527 578000 - Fax +44 01527 578170info@kerakoll.co.uk - www.kerakoll.com

Fuga-Shock Eco is a liquid detergent. Before using the product, it is advisable to hermetically seal all doors, windows, rubber seals, furniture, varnished/painted elements, bathtubs and shower trays made of synthetic materials such as methacrylate, PVC, etc..and any surface that could be attacked through direct contact with the detergent or with vapours.

SPECIAL NOTES

- Product for professional use- abide by any standards and national regulations- store and use at a temperature above +5 °C. Protect from frost- rinse thoroughly all surfaces treated- do not leave cans or bottles open, even during use- wear protective gloves and goggles- leaving the product to act for more than 5 minutes may result in physical and colour alterations in the grout- if necessary, ask for the safety data sheet- for any other issues, contact the Kerakoll Worldwide Global Service 01527 578000 - info@kerakoll.co.uk

WARNING

Appearance Transparent liquidSpecific weight ≈ 1,05 kg/dm3

Shelf life ≈ 24 months in the original packagingWarning Protect from frost, avoid direct exposure to sunlight and sources of heatPack bottles 1 ℓWater dilution ratios All ratiosViscosity ≈ 1540 mPa · s, rotor 2 RPM 50 Brookfield methodpH ≈ 1,4Temperature range for application from +5 °C to +35 °CWaiting time before cleaning with water ≈ 2 – 5 min.Coverage ≈ 10 – 20 m2/1 ℓValues taken at +23 °C, 50% R.H. and no ventilation. Data may vary depending on specific conditions at the building site, i.e.temperature, ventilation and absorbency level of the substrate and of the materials laid.

TECHNICAL DATA COMPLIANT WITH KERAKOLL QUALITY STANDARD

0080

0 Fu

ga-S

hock

Eco

Cod

e: P

965

2015

/11

UK