Cat Dealers define world-classproduct support. We offer you theright parts and service solutions,when and where you need them.

The Cat Dealer network of highlytrained experts keeps your entirefleet up and running to maximizeyour equipment investment.

Caterpillar. The difference counts.™Recommended UseCat Ultra 5Moly Grease is formulated for grease fittings and lubrication pointsin high-load and high-speed applications with ambient temperatures rangingfrom -35° to 40°C (-31° to 104°F) for NLGI #1 and -30° to 50°C (-22° to122°F) for NLGI #2.

Discover the DifferenceCat Ultra 5Moly Grease is developed, tested and approved by Caterpillar to meetthe same high standards as Genuine Cat Parts.Long Life—High-quality calcium sulfonate complex formula with 5%molybdenum disulfide moly provides long service life in Cat applications.Moisture Resistance—Resists washout from fresh and salt water.Reduced Component Wear—Resists softening and continues to protect partsunder extreme loads and high speeds.Corrosion Protection—Resists oxidation and protects metal against rust. Willnot corrode or damage steel, copper bearing alloys or conventional sealmaterials.Low Environmental Risk—Is formulated to use no lead, antimony, zinc,barium, chlorine, phosphorus or free sulfur.

NLGI Grade 1, 2For grease fittings and lubrication points in high-load and high-speed applications.

Cat® Ultra 5Moly Grease

Typical Characteristics*NLGI # 1 2Ambient Range, F -31° to +104° -22° to +122°Ambient Range, C -35° to +40° -30° to +50°Operating Range, F -40° to +300° -25° to +300°Operating Range, C -40° to +149° -32° to +149°Base Fluid Type Petroleum PetroleumThickener Type Calcium Sulfonate Calcium Sulfonate

Complex ComplexColor Gray Gray% Molybdenum disulfide 5 5Worked Penetration (mm) 310-340 265-295% Change/100,000 stroke +/-5 +/-5Roll Stability w/H2O, % change +/-5 +/-5Viscosity Index, Min N/A N/AViscosity @ 100°C, cSt 11.5 11.5Viscosity @ 40°C, cSt 150 1504 Ball Wear (mm) Max, Typ. 0.5 0.54 Ball E.P. Weld Point (kg) Min. 620 620Timken E.P. Test OK load (lb) Typ. 60 60Oxidation-psi drop/500 hr Max N/A N/ARust Test Pass PassSalt Fog Test, hours +4,000 +4,000Copper Corrosion 1a 1aDropping Point +288°C (+550°F) +288°C (+550°F)

Cat Ultra 5Moly Grease

NEHP6010-01 www.cat.com © 2005 Caterpillar All Rights Reserved Printed in USA

Health and SafetyFor information on proper use for health, safety, and environment, please refer to

the Material Safety Data Sheet (MSDS). Read and understand the MSDS before

using this product. Always observe good hygiene measures. For a copy of the

MSDS, contact us or visit the web at www.catmsds.com.

Other Recommended GreasesCat Desert Gold™ Grease

For extremely hot temperatures upto 60°C (140°F).

Cat Arctic Platinum™ GreaseFor extremely cold temperaturesdown to -50°C (-58°F).

*The values shown are typical values and should not be used as quality control parameters to eitheraccept or reject product. Specifications are subject to change without notice.

High Temp Low LoadMedium LoadLow TempHigh Load

Cat Arctic Platinum GreaseNLGI 0

(Temp down to -50°C / -58°F)With 5% moly

Cat High Speed Ball Bearing GreaseNLGI 2

(Temp above -20°C / -4°F)Without moly

Cat Ultra 5Moly GreaseNLGI 1

(-35° to 40°C / -31° to 104°F)With 5% moly

Cat Ultra 5Moly GreaseNLGI 2

(-30° to 50°C / -22° to 122°F)With 5% moly

Cat Desert Gold GreaseNLGI 2

(Temp up to 60°C / 140°F)With 5% moly

Cat Advanced 3Moly GreaseNLGI 2

(-20° to 40°C / -4° to 104°F)With 3% moly

Cat Multipurpose GreaseNLGI 2

(-30° to 40°C / -22° to 104°F)

Without moly

WorkingEnvironment

Low LoadAnd High Speed

*All temperatures are ambient.

Grease Selection Guide*