Upload
tecnosmart
View
221
Download
0
Embed Size (px)
Citation preview
8/9/2019 camara vivotek IP7153
1/12
8/9/2019 camara vivotek IP7153
2/12
EN - 1
English
Contact your distributor in the event of
occurrence.
Keep the Network Camera away fromwater. If the Network Camera becomes
wet, power off immediately.
Refer to your users manual for the
operating temperature.
Power off the Network Camera assoon as smoke or unusual odors
are detected.
Do not place the Network Camera
around heat sources, such as a
television or oven.
Keep the Network Camera away
from direct sunlight.
Do not place the Network Camera in
high humidity environments.
Contact your distributor in the event of
occurrence.
Warning Before Installation
8/9/2019 camara vivotek IP7153
3/12
EN - 2
Do not place the Network Cameraon unsteady surfaces.
Do not touch the Network Cameraduring a lightning storm.
Do not disassemble the Network
Camera.
Do not drop the Network Camera.
Do not insert sharp or tiny objects
into the Network Camera.
8/9/2019 camara vivotek IP7153
4/12
EN - 3
English
Camera Stand Lens
IP7153 / IP7154
Warranty Card
Power Adapter
Quick Installation Guide Software CD
1 Check Package Contents
Antenna (IP7154 only)
ST7501Central ManagementSoftware
8/9/2019 camara vivotek IP7153
5/12
EN - 4
Power Cord SocketEthernet 10/100
RJ45 Socket
Recessed Reset ButtonGeneral I/OTerminal Block
Audio OutMicrophone In
External/InternalMicrophone Switch
Front Panel
Back Panel
Lens
Focus Controller
Zoom Controller
2 Physical Description
Built-in MicrophoneLight Sensor
Status LED
Antenna(IP7154 only)
Antenna(IP7154 only)
8/9/2019 camara vivotek IP7153
6/12
EN - 5
English
For further setup, please refer to the lens' instruction manual inside the
lens package.
1. Mount the lens by turning it clockwise onto the camera mount until it stops. Ifnecessary, turn the lens counterclockwise slowly to achieve the best optimumspacing.
2. Connect the lens cable plug to the camera connector.
3. Unscrew the zoom controller to adjust the zoom factor. Upon completion, tighten thezoom controller.
4. Unscrew the focus controller to adjust the focus range. Upon completion, tighten thefocus controller.
W
N
T
1
2
4
3
3 Mounting the Lens to the Camera
8/9/2019 camara vivotek IP7153
7/12
EN - 6
General Connection (without PoE)1. Connect the camera to a switch via Ethernet cable.
2. Connect the power cable from the Network Camera to a power outlet.
POWERCOLLISION
LINK
RECEIVE
PARTITION1 2 3 4 5
1
2
Ethernet Switch
4 Network Deployment
8/9/2019 camara vivotek IP7153
8/12
EN - 7
English
Power over Ethernet (PoE) (IP7153 only)
POWERCOLLISION
LINK
RECEIVEPARTITION
1 23 4
5
PoE Switch
POWERCOLLISION
LINK
RECEIVEPARTITION
12 3 4 5
When using a non-PoE switch
Use a PoE power injector (optional) to connect between the Network Camera and anon-PoE switch.
Non-PoE Switch
PoE Power Injector
(optional)
When using a PoE-enabled switch
This Network Camera is PoE-compliant, allowing transmission of power and data via
a single Ethernet cable. Follow the below illustration to connect the Network Camera
to a PoE-enabled switch via Ethernet cable.
8/9/2019 camara vivotek IP7153
9/12
EN - 8
This device complies with part 15 of the FCC rules. Operation is subject tothe following two conditions:(1)This device may not cause harmful interference, and(2) this device must accept any interference received, including interferencethat may cause undesired operation.
RoHS
Network Camera
Model No:IP7153
Pat. 6,930,709 Made in Taiwan
MAC:0002D1070417
1. Install "Installation Wizard 2" from the Software Utility directory on the software CD.2. The program will conduct an analysis of your network environment. After your network
is analyzed, please click on the "Next" button to continue the program.
3. The program will search for VIVOTEK Video Receivers, Video Servers, and NetworkCameras on the same LAN.
4. After searching, the main installer window will pop up. Click on the MAC that matchesthe one labeled on the bottom of your device to connect to the Network Camera viaInternet Explorer.
00-02-D1-07-04-17 192.168.0.219 IP7153
Installation
Wizard 2
5 Assigning an IP Address
0002D1070417
8/9/2019 camara vivotek IP7153
10/12
EN - 9
English
For further setup, please refer to user's manual on the software CD.
6 Ready to Use
1. Access the Network Camera on the LAN.2. Retrieve live video through the web browser or recording software.
8/9/2019 camara vivotek IP7153
11/12
EN - 10
7 Configure the Wireless Connection (IP7154 only)
1. Check the SSID for your wireless access point (AP).2. Go to the IP7154 Configuration page > Advanced mode > Wireless LAN.
Note:
1. SSID, abbreviated from Service Set Identifier, is the name assigned to the wirelessnetwork. The IP7154 factory SSID setting is set to "default".
2. Select "Ad-Hoc" wireless mode if you want the IP7154 to communicate withoutusing an AP or wireless router.
POWER COLLISION
LINK
RECEIVE
PARTITION
12 3 4
5
ADSL/Cable
/Hub
AP
3. Type in the SSID the same asyour AP.
4. Select the Wireless mode as"Infrastructure".
5. Click Save. The NetworkCamera will reboot.
For further setup, please refer to the user's manual on the software CD.
6. Wait for the live image to be reloaded to yourbrowser. Then, unplug the power cable and Ethernetcable from the Network Camera.
7. Replug the power cable to the camera. The NetworkCamera will now operate in wireless mode.
8/9/2019 camara vivotek IP7153
12/12
P/ N: 625009000G Ver.1.01Co pyright 2009 VIVOTEK INC. All right reserved .