C ATALOGUE OF PRODUCTS 2015 VINCI · PDF fileVINCI TECHNOLOGIES ATALOGUE OF PRODUCTS FLUID YSIS C 2015 FLUID ANALYSIS PVT H/C Composition Flow assurance Fluid sampling

VIN

CI

TE

CH

NO

LO

GIE

S

FL

UID

AN

AL

YS

IS

CATALOGUE OF PRODUCTS

2015

FLUID ANALYSIS

PVT H/C Composition

Flow assurance Fluid sampling

VINCI TECHNOLOGIES

Parc de l'Ile, 27B rue du Port, 92022 NANTERRE

Phone: 331 41 37 92 20 Fax: 331 41 37 04 76

e-mail: [email protected]

http://www.vinci-technologies.com 3/75

FL

UID

AN

AL

YS

IS

LIST OF INSTRUMENTS

FLUID BEHAVIOUR STUDIES ________________________________ 6

PVT SYSTEM FOR PVT AND ASPHALTENE & WAX STUDIES (STANDARD & MAXI FLUID EVAL)6

FULLY VISUAL PVT SYSTEM (VISUAL FLUID EVAL) ______________________________ 7

FIELD PVT SYSTEM (MOBILE FLUID EVAL) ___________________________________ 8

EDUCATIONAL PVT CELL (EDUCATIONAL FLUID EVAL) ___________________________ 9

BUBBLEPOINT PRESURE APPARATUS (BPP 70) _____________________________ 10

MANUAL GASOMETER (MG SERIES) ______________________________________ 11

AUTOMATED GASOMETER (AG SERIES) ___________________________________ 12

LIQUID CONDENSATION TRAP ___________________________________________ 13

GAS OIL RATIO APPARATUS____________________________________________ 14

GOR SAMPLE PYCNOMETER ____________________________________________ 15

GAS PYCNOMETER __________________________________________________ 16

EQUILIBRIUM FLASH SEPARATOR APPARATUS _______________________________ 17

MULTI STAGE SEPARATOR APPARATUS ___________________________________ 18

VISCOSITY ______________________________________________ 19

ROLLING BALL VISCOMETER (RBV 1000) _________________________________ 19

CAPILLARY VISCOMETER (CV SERIES) ____________________________________ 20

ELECTROMAGNETIC VISCOMETER (EV 1000) _______________________________ 21

HEAVY OIL VISCOMETER (HOV 700) _____________________________________ 22

DENSITY ________________________________________________ 23

HP HT DENSITY CELL _________________________________________________ 23

DIGITAL DENSITOMETER ______________________________________________ 24

COMPOSITIONAL ANALYSIS _______________________________ 25

HYDROCARBON COMPOSITIONAL ANALYSER ________________________________ 25

MOLECULAR WEIGHT TESTER __________________________________________ 26

ASPHALTENES AND WAXES STUDIES ______________________ 27

FLOW ASSURANCE SYSTEM (FLASS) ____________________________________ 27

RESERVOIR FLUID PARTICLE ANALYSER (RFP) ______________________________ 28

HIGH PRESSURE MICROSCOPE (HPM) ___________________________________ 29

SOLID DETECTION SYSTEM (SDS) _______________________________________ 30

FLOCCULATION TITRIMETER (FT SERIES) __________________________________ 31

AUTOMATED HEITHAUS FLOCCULATION TITRIMETER (FT-A) ___________________ 32

ORGANIC SOLID FILTER (OSD 1000) _____________________________________ 33

ASPHALTENE DESPOSITION LOOP (ASPHALTEVAL) ___________________________ 34

WAX DEPOSITION FLOW LOOP FOR STOCK OIL SAMPLE (WAX-EVAL A) ____________ 35

SMALL SIZE WAX FLOW LOOP FOR LIVE OIL SAMPLE (WAX-EVAL SS200) __________ 36

MEDIUM SIZE WAX FLOW LOOP FOR LIVE OIL SAMPLE (WAX-EVAL MS150)_________ 37

mailto:[email protected]

VINCI TECHNOLOGIES


Phone: 331 41 37 92 20 Fax: 331 41 37 04 76



FL

UID

AN

AL

YS

IS

MULTI-PLACE COLD FINGER (MFC 6) _____________________________________ 38

FLOW-THROUGH SDS CELL (FTC SERIES) _________________________________ 39

HIGH PRESSURE ROTARY VANE FLOW METER (RVF SERIES) ____________________ 40

FLOOR STAND STIRRED PRESSURE VESSEL (FSV SERIES) ______________________ 41

HYDRATES STUDIES ______________________________________ 42

GAS HYDRATES AUTOCLAVE SYSTEM (GHA SERIES) _________________________ 42

HYDRATES STUDIES SYSTEM (HYDREVAL) _________________________________ 43

HYDRATES KINETICS STUDIES SYSTEM (KINETIC-EVAL) _______________________ 44

FLUID-EVAL FOR HP- HT VISUAL STUDIES (BENCH TOP VISUAL VERSION) ___________ 45

SCALE DEPOSITION STUDIES ______________________________ 46

DYNAMIC SCALE LOOP (SCALEVAL) ______________________________________ 46

BRINE CRYSTALLIZATION TEMPERATURE ___________________ 47

PRESSURIZED BRINE CRYSTALLIZATION TESTER (PCT1300) ____________________ 47

EMULSIONS _____________________________________________ 48

EMULSION PRESSURE DROP LOOP (EMULSEVAL) ____________________________ 48

FLUID PUMPABILITY ______________________________________ 49

FRICTION FLOW LOOP FOR EVALUATING DRAG REDUCING AGENTS (DRA FLOW LOOP) __ 49

RHEOLOGY _____________________________________________ 50

HIGH PRESSURE RHEOMETER (RHEO 1000) ________________________________ 50

SAMPLING ______________________________________________ 51

PVT SURFACE SEPARATOR SAMPLING KIT _________________________________ 51

BOTTOM HOLE SAMPLER ______________________________________________ 52

TRANSFER BENCH ___________________________________________________ 53

HIGH PRESSURE PISTON SAMPLE CYLINDER (HPP SERIES) _______________ 54

MICRO HIGH PRESSURE PISTON SAMPLE CYLINDER (MHP SERIES) _______________ 55

LIGHT WEIGHT PISTON SAMPLE CYLINDER (CYLIGHT SERIES) _________________ 56

SINGLE PHASE SAMPLE CYLINDER (SPS SERIES) ____________________________ 57

LOW PRESSURE PISTON SAMPLE CYLINDER (LPP SERIES) _______________ 58

FLOW THROUGH SAMPLE CYLINDER (FTS SERIES) ___________________________ 59

GAS SAMPLE CYLINDER (GS SERIES) _____________________________________ 60

FLOATING PISTON ACCUMULATOR (FPA SERIES) ____________________________ 61

SAMPLE PREPARATION ___________________________________ 62

MIXER CYLINDER (MC SERIES) _________________________________________ 62

RECOMBINATION CELL APPARATUS (RCA 1000) ____________________________ 63

MOBILE RECOMBINATION AND RESTORATION APPARATUS (MRR 1000) ___________ 64

SAMPLE RESTORATION APPARATUS ______________________________________ 65

GAS SAMPLE RESTORATION APPARATUS __________________________________ 66

CYLINDER HEATING MANTLE ___________________________________________ 67

HEATING TROLLEY FOR LIQUID CYLINDER __________________________________ 68

HEATING TROLLEY FOR GAS CYLINDER ____________________________________ 69


VINCI TECHNOLOGIES


Phone: 331 41 37 92 20 Fax: 331 41 37 04 76



FL

UID

AN

AL

YS

IS

GAS BOOSTER (GB – SERIES) __________________________________________ 70

SOLVENT CLEANER __________________________________________________ 71

PRESSURE GENERATOR SYSTEM (PGS) __________________________________ 72

CALIBRATION ___________________________________________ 73

DEADWEIGHT GAUGE ________________________________________________ 73

DIGITAL PRESSURE GAUGE (DPG SERIES) __________________________________ 74

POWER SUPPLY BACK UP_________________________________ 75

UNINTERRUPTIBLE POWER SUPPLY (UPS 16) ______________________________ 75

The specifications and photos contained in this catalogue can be subject to change without

notification.

Copyright© Vinci Technologies. All rights reserved.


VINCI TECHNOLOGIES


Phone: 331 41 37 92 20 Fax: 331 41 37 04 76



FL

UID

AN

AL

YS

IS

Fluid behavi our s tudi es

PVT SYSTEM FOR PVT AND ASPHALTENE & WAX STUDIES

(STANDARD & MAXI FLUID EVAL)

The Fluid Eval PVT system is designed to study phase behavior of hydrocarbon fluids

at reservoir conditions of pressure and temperature. It can be used to perform PVT tests

on black oil, volatile oil and gas condensate samples. It can also be configured with

additional infrared, laser based solid detection system (SDS) and high pressure

microscope (HPM) to perform a variety of asphaltenes and wax solid

deposition experiments.

FEATURES

Cell volume: 500 cc (standard Fluid Eval model)

1,000 cc (maxi Fluid Eval model)

Pressure: 15,000 psi

Temperature: Ambient to 200°C (option: -20°C)

Temperature regulation: ± 0.5 °C

Volume accuracy: 0.01 ml

Pressure accuracy: 0.1% Full scale

Liquid deposit accuracy: ± 0.01 ml

Power supply: 220 VAC, 50/60 Hz

BENEFITS

Versatile design

Mercury free operation

Large cell volume for representative sample studies

Automated phase detection and phase volume measurement

Embedded pump for precise pressure control and volume measurement

Video camera system for recording PVT experiments in real time

Magnetic driven stirrer for rapid phase equilibrium

Motorized rocking system for cell positioning

Sub-ambient temperature control

Add-on modules for solid detection, viscosity and density measurement


VINCI TECHNOLOGIES


Phone: 331 41 37 92 20 Fax: 331 41 37 04 76



FL

UID

AN

AL

YS

IS

FULLY VISUAL PVT SYSTEM (VISUAL FLUID EVAL)

The fully visual Fluid Eval PVT system is designed to study phase behavior of reservoir

fluids at reservoir conditions of pressure and temperature. The PVT cell is based on a

window through cell offering full sample visibility. It is particularly interesting when

visual observation of the fluid must be accomplished such as swelling tests, volatile oil

studies, gas condensates, etc. The system uses an embedded high pressure pump to

control the pressure and volume of the reservoir fluid in the cell. A motorized rocking

system permits to rock the cell for faster recombination and also put the cell in the

correct position before the fluid volume measurement takes place. A video camera

system records in real time the fluid phases while video tools enable the end-user

to retrieve the volume of each phase versus pressure and temperature. A magnetic

coupled stirrer mounted inside the sample chamber provides efficient fluid mixing and

ensures fast equilibrium of sample phases. Homogeneous sample heating is provided by

heating cartridges inserted in the cell body.

FEATURES Volume / Pressure: 15,000 psi /400 ml (Visual Fluid Eval model)

25,000 psi / 250 ml (HP Visual Fluid Eval model)

10,000 psi / 1500 ml (Extended Visual Fluid Eval model)

Temperature: up to 200°C

Temperature regulation: 0.2 oC


Liquid deposit accuracy: 0.005 ml

Power supply: 220 VAC 50/60 Hz

BENEFITS Versatile design


Minimum dead volume

Full sample visibility for greater operational capability




Motorized rocking system for cell positioning

High temperature pressure transducer with extreme accuracy of 0.02% FS

Special polyimide sealing resistant against fast gas decompression

Sub-ambient temperature control


VINCI TECHNOLOGIES


Phone: 331 41 37 92 20 Fax: 331 41 37 04 76



FL

UID

AN

AL

YS

IS

FIELD PVT SYSTEM (MOBILE FLUID EVAL)

The mobile Fluid Eval PVT system is designed to perform PVT tests on reservoir

fluids at the field location or in the laboratory. The system uses an embedded high

pressure pump to control the pressure and volume of the reservoir fluid in the cell.

The unit can be configured for either oil or gas condensates studies by inverting the

position of the cell. A video camera system automatically determines the gas/liquid

interface and measures the volume of retrograde condensate during gas condensate

studies. A magnetic coupled stirrer mounted inside the sample chamber provides

efficient fluid mixing and ensures fast equilibrium of sample phases. Sample heating is

provided by an heating jacket wrapped around the cell.

FEATURES


Temperature: Ambient to 175°C (350 °F)


Cell volume: 100 cc with 10 cc visual





BENEFITS

Mobile and transportable

Versatile design


Touch screen panel for easy operation






VINCI TECHNOLOGIES


Phone: 331 41 37 92 20 Fax: 331 41 37 04 76



FL

UID

AN

AL

YS

IS

EDUCATIONAL PVT CELL (EDUCATIONAL FLUID EVAL)

The educational Fluid Eval instrument is a compact PVT cell designed for the study of

PVT, thermodynamic properties and phase behaviour of black oil and gas condensate

samples requiring a small volume of fluid sample. The PVT cell is composed of an

efficient fluid mixer mounted on the piston, a dedicated visual head, two sampling

valves, an accurate pressure transducer and an electric heater for homogeneous

temperature control . A digital camera system permits observation of the liquid/gas

interface through the sapphire windows. During differential vaporization and flash test,

the removal of the gas phase is facilitated by the full visibility of the gas/oil interface

through the window of the cell. The unit can be configured for either oil or gas

condensates studies by inverting the position of the cell.

FEATURES




Cell volume: 100 cc





BENEFITS

Versatile design

Cost effective PVT cell

Designed for instructional purposes

Easy to use by educational and research establishments


Requires small sample volume

Computer controlled with PVT reporting facilities




Manual rocking system for cell positioning


VINCI TECHNOLOGIES


Phone: 331 41 37 92 20 Fax: 331 41 37 04 76



FL

UID

AN

AL

YS

IS

BUBBLEPOINT PRESURE APPARATUS (BPP 70)

Surface liquid samples are validated in the PVT lab by measuring the sample’s bubblepoint

pressure in particular. One of the most important quality checks performed on such samples

consists in verifying that the measured bubblepoint pressure matches the pressure of the

separator recorded during the sampling operations. The BPP 70 apparatus has been designed to

measure the bubblepoint pressure of separator oil at separator temperature. A flash liberation

test is performed on the homogenised sample to determine the bubblepoint pressure by

analysing the recorded pressure-volume response at separator temperature. The apparatus can

also be configured with three sample cells.

FEATURES

Model: Model 1: BPP 70-1 with one cell

Model 2: BPP 70-3 with three cells

Temperature: Ambient to 150°C (300°F)

Cell volume: 100 ml

Pressure: atmospheric to 1,000 psi

Temperature accuracy: 0.2 oC


Pressure accuracy: 0.1% FS

Wetted parts: Stainless steel


BENEFITS

Fast and accurate determination of bubblepoint pressure

Easy to use

Avoid to use a PVT cell which can be used for reservoir fluids instead.


VINCI TECHNOLOGIES


Phone: 331 41 37 92 20 Fax: 331 41 37 04 76



FL

UID

AN

AL

YS

IS

MANUAL GASOMETER (MG SERIES)

The manual gasometer is designed to measure gas volumes at ambient conditions of pressure

and temperature. The gas enters the calibrated cylinder and raises the floating piston upwards,

thus incrementing the volume space in the cylinder. A hand operated crank allows for the

operator to adjust the position of the piston at the desired pressure and volume. The volume,

temperature and pressure of the gas are continuously monitored and displayed. The gasometer is

provided with inlet and outlet valves.

FEATURES

Volume: 4 liters

Pressure: Vacuum to 20 psi

Volume reading: 0.1 ml

Pressure accuracy: 0.1%

Temperature resolution: 0.1°C

Weight 21 Kg

LxDxH 350 x 250 x 820 mm


Power supply: 220 VAC 50 Hz

BENEFITS

Very easy to use

Accurate measurement of volume, pressure and temperature


VINCI TECHNOLOGIES


Phone: 331 41 37 92 20 Fax: 331 41 37 04 76



FL

UID

AN

AL

YS

IS

AUTOMATED GASOMETER (AG SERIES)

The automated gasometer is designed to measure gas volumes at ambient temperature and

atmospheric pressure. The gasometer is made of a calibrated stainless steel chamber equipped

with a motor driven piston. The gas enters the chamber at constant pressure or at constant flow

rate. The volume, temperature and pressure of the gas are continuously monitored and

displayed. The gasometer is provided with inlet and outlet valves. The whole is mounted on a

chassis equipped with four heavy duty casters.

FEATURES

Volume: 10 liters

Max Gas flow rate: 10 Liters/min



Pressure accuracy: 0.1%

Temperature resolution: 0.1°C

Temperature: Ambient, option 50°C



BENEFITS

Accurate measurement of volume

Gas transfer at constant pressure or constant flow rate

Automated operations


VINCI TECHNOLOGIES


Phone: 331 41 37 92 20 Fax: 331 41 37 04 76



FL

UID

AN

AL

YS

IS

LIQUID CONDENSATION TRAP

Designed to trap heavy compounds which might be produced during the liberation of the gas phase

from the reservoir to the atmospheric conditions. The cooling trap is installed between the PVT cell

and the gasometer. It consists of a cooling unit based on Peltier effect and a pyrex trap cylinder of 10

cc capacity. The temperature can reach up to -10°C. The composition of the trapped condensates can

be analysed by gas chromatography.

FEATURES

Volume: 10 cc


Temperature: -10°C to Ambient


BENEFITS

Compact, no use of cooling liquid.


VINCI TECHNOLOGIES


Phone: 331 41 37 92 20 Fax: 331 41 37 04 76



FL

UID

AN

AL

YS

IS

GAS OIL RATIO APPARATUS

The purpose of the GOR apparatus is to flash pressurised liquids and measure the gas oil ratio at

equilibrium conditions. The liberated gas is measured with the gasometer at ambient conditions

while the dead oil flashed is determined by gravity technique. The GOR apparatus features the

capability of recirculating the evolved gas back through the on board high pressure oil

pycnometer and gas pycnometer. This recirculation ensures vapor liquid equilibrium and allows

the operator easy access to representative homogeneous samples of atmospheric pressure vapour

and liquids. The establishment of equilibrium is essential for high pressure volatile liquids such

as those encountered in reservoir fluid studies.

FEATURES

Temperature: Ambient

Flow rate: 100 cc/min

Pressure: atmospheric


BENEFITS

Representative homogeneous samples

Easy to use


VINCI TECHNOLOGIES


Phone: 331 41 37 92 20 Fax: 331 41 37 04 76



FL

UID

AN

AL

YS

IS

GOR SAMPLE PYCNOMETER

This U-tube pycnometer is used for determining the GOR of a live oil. It is based on a flow

through vessel equipped with two needle valves and a burst disc. It is provided with a tare

weight and calibrated volume. A predefined volume of lived oil sample is transferred into the

pycnometer and the gas is released from the pycnometer to the gasometer by opening the valve

slowly for determining the gas volume. The volume of flashed liquid remaining in the

pycnometer is determined by measuring its weight and density. The GOR can then be derived.

FEATURES

Volume : 75 cc

Max pressure: 1,800 psi

Max temperature: Ambient

Material: Stainless steel

BENEFITS

Easy to use


VINCI TECHNOLOGIES


Phone: 331 41 37 92 20 Fax: 331 41 37 04 76



FL

UID

AN

AL

YS

IS

GAS PYCNOMETER

This pycnometer is used for gas sampling and GC analysis. It is based on a flow through vessel

equipped with two needle valves and a burst disc.

FEATURES

Volume : 75 cc

Max pressure: 1,800 psi

Max temperature: Ambient


BENEFITS

Easy to use


VINCI TECHNOLOGIES


Phone: 331 41 37 92 20 Fax: 331 41 37 04 76



FL

UID

AN

AL

YS

IS

EQUILIBRIUM FLASH SEPARATOR APPARATUS

Designed to flash pressurised liquids and measure the gas oil ratio at equilibrium conditions.

The liberated gas is measured with the gasometer at ambient conditions while the liquid is read

in a sample graduated burette. It is based on two stage system with first stage at maximum

pressure of 500 psi and second at atmospheric pressure. It consists of a precision bore, high

pressure Pyrex cylinder of 40 cc capacity with stainless steel closures on both ends, pressure

gauge, back pressure regulator, valves and tubing. All components are assembled on a metal

panel.

FEATURES

Volume: 40 cc


Volume accuracy: 0.1 cc

Wetted parts: Pyrex and stainless steel

Power supply: 220 VAC, 50 Hz

BENEFITS

Very easy to use

Accurate measurement of liquid volume

Possibility to heat sample with an external heating fluid


VINCI TECHNOLOGIES


Phone: 331 41 37 92 20 Fax: 331 41 37 04 76



FL

UID

AN

AL

YS

IS

MULTI STAGE SEPARATOR APPARATUS

This equipment is designed to simulate a full-scale field separation unit. It is used to determine

the optimum conditions of separation by calculating the changes in formation volume factor and

gas-oil ratios with changes in separator pressure and temperature. A reservoir fluid sample is

brought at its bubble point pressure and reservoir temperature in a PVT cell. A known volume

of this sample is then transferred into the separator cell at separator conditions of pressure and

temperature. As a result of these thermodynamic changes, gases evolve from the liquids. The

volumes of liquid and gas are measured at the separator conditions and the gas released is also

measured by a gasometer at standard conditions. The separator test is usually carried out at a

number of separator pressures in order to determine the optimum field separator conditions. The

final step is carried out at atmospheric pressure. The main parameters which are determined by

the experiments include the formation volume factor, the separator volume factor and the

solution gas-oil ratio.

FEATURES

Working pressure: Up to 200 bar (3,000 psi)

Working temperature: 10 to 100 °C (215 °F)

Volume of the separator cell: 250 ml

Stirring mechanism: Magnetic driven stirrer

Pressure accuracy: 0.1 %

Temperature accuracy: +/-0.1 °C


Electrical: 220 VAC, 50/60 Hz, 1 phase

BENEFITS

Equilibrium conditions are fast to attain

Accurate measurement of liquid and gas volumes

Efficient stirring operation of the test fluid


VINCI TECHNOLOGIES


Phone: 331 41 37 92 20 Fax: 331 41 37 04 76



FL

UID

AN

AL

YS

IS

Viscosity

ROLLING BALL VISCOMETER (RBV 1000)

The rolling ball viscometer is designed to determine the viscosity of bottom-hole and surface oil

samples at elevated temperature and pressure. It uses the rolling ball principle where the roll

time of a piston is used to obtain viscosity data. Viscosity values are then obtained by

correlation of the measured data with curves of fluids with known viscosities. The RBV 1000

consists of a calibrating barrel equipped with a latch at its upper end and an laser detector at its

lower end. The latch permits to trap and release the piston while the detector detects the arrival

of the piston allowing for the roll time to be determined. The viscometer features a jacket for

circulating heating fluid around the chamber to ensure a constant and homogeneous temperature

of the sample. A computer system acquires the roll time and calculates the viscosity value.

FEATURES

Pressure range: 15,000 psi

Temperature range: ambient to 190°C

Viscosity range: 0.2 to 10,000 cP

Cylinder slope: 45°, 65°

Sample volume required: 11 ml


BENEFITS

Easy to use

Calibration procedure provided

Accurate measurement for particular heavy oil

Reservoir conditions of pressure and temperature

Large range of viscosity

Cost effective


VINCI TECHNOLOGIES


Phone: 331 41 37 92 20 Fax: 331 41 37 04 76



FL

UID

AN

AL

YS

IS

CAPILLARY VISCOMETER (CV SERIES)

The capillary viscometer is designed for the determination of viscosity of single phase fluids at

reservoir conditions for both vapour and liquid sample. The instrument is based on the

Poiseuille’s law which defines fluid viscosity as a function of the pressure drop in a fluid

flowing laminarly through a capillary. It includes four capillary columns to cover the range of

viscosity of most reservoir fluids from 0.02 cp to 10,000 cp and is rated for 10,000 psi. It

consists of a high temperature twin syringe pump used to generate the constant flow rate, four

capillary tubes, two pressure transducer, a temperature probe and a controlled temperature

airbath.

FEATURES

Pressure: 10,000 psi (model CV700)

15,000 psi (model CV1000)

Temperature: Ambient to 200°C (400°F)

Temperature regulation: ±0.5°C

Viscosity range: 0,01 cP to 10,000 cP


BENEFITS

Accurate measurement


No need to change any components during the test



VINCI TECHNOLOGIES


Phone: 331 41 37 92 20 Fax: 331 41 37 04 76



FL

UID

AN

AL

YS

IS

ELECTROMAGNETIC VISCOMETER (EV 1000)

The EV 1000 instrument is based on a simple and reliable electromagnetic concept. Two coils

move the piston back and forth magnetically at a constant force. Proprietary circuitry analyzes

the piston’s two-way travel time to measure absolute viscosity. A built-in temperature detector

(RTD) senses the actual temperature in the sampling chamber. The viscometer consists of a

Cambridge Electromagnetic Viscometer SPSL 440, a set of six calibrated pistons to cover

viscosity ranging from 0.02 cP to 10,000 cP, a pressure transducer with its digital display, a

temperature probe and a controlled heating jacket.

FEATURES

Brand: Cambridge Electromagnetic Viscometer, SPSL 440 model

Temperature range: up to 190°C

Pressure range: up to 15,000 psi

Viscosity range: 0.02 cP to 10,000 cP

Accuracy: ±1% FS

Reproducibility: ±0.8 % of reading

Temperature sensor: Internal platinum RTD

Wetted material: Inconel 718

Temperature regulation: ±0.5°C


BENEFITS

Accurate measurement


Reservoir conditions



VINCI TECHNOLOGIES


Phone: 331 41 37 92 20 Fax: 331 41 37 04 76



FL

UID

AN

AL

YS

IS

HEAVY OIL VISCOMETER (HOV 700)

The Heavy Oil Viscometer consists in a straight metal rod maintained in vibration permanently

by a constant power. The amplitude of the vibration varies according to the viscosity of the fluid

in which the rod is immersed. The electronics ensures an adequate vibration and treats the

variations of amplitude to obtain the viscosity value. The viscometer module is assembled with

a 15cc measurement cell to get a stand alone viscometer. A drain valve also enables to release

gas when saturation pressure is reached. The cell is designed to be removed easily for fast and

efficient cleaning.

FEATURES

Viscosity range: 10,000 Cp to 106Cp (model A)

1,000 Cp to 105Cp (model B)

Accuracy: 3% RM

Repeatability: ±0.2%

Volume of sample: 15cc

Working temperature: up to 180 °C

Working pressure: 700 bar

Construction: Stainless Steel 316L, Hastelloy

BENEFITS

Sensor without moving parts

Very high viscosity range

Robust and reliable

Accurate

Zero maintenance

Simple operation by immersing the sensor probe into the fluid, measure and wipe after use.


VINCI TECHNOLOGIES


Phone: 331 41 37 92 20 Fax: 331 41 37 04 76



FL

UID

AN

AL

YS

IS

Densi ty

HP HT DENSITY CELL

The HP HT density cell handles reservoir fluids at pressures up to 10 Kpsi and temperatures

up to 175 °C. The principle consists of transferring the sample into the cell at reservoir

conditions and weighing the cell filled up with the sample using a high resolution balance. The

density of the sample is calculating by simply dividing the weight of the sample (i.e. weight of

the filled cell minus weight of the evacuated cell) by the known volume of the cell. This

method provides reliable, correct and repeatable measuring results under extreme

conditions. The resolution of the density measurement mainly depends on the balance used.

Combined with a balance with a weighing measure accuracy of 1 mg the maximum resolution

of 0.0006 g/cm3 can be achieved.

FEATURES

Volume: 4 cc

Weight 182.15 grams

Max pressure: 10,000 psi (700 bar)

Max temperature: Ambient to 175°C (350°F)

Material: Titanium

BENEFITS

Easy to use

Cost effective


VINCI TECHNOLOGIES


Phone: 331 41 37 92 20 Fax: 331 41 37 04 76



FL

UID

AN

AL

YS

IS

DIGITAL DENSITOMETER

The digital densitometer consists of a high pressure, high temperature cell made from hastelloy

to cover the range of density of most reservoir fluids from 0 to 3 g/cm3. It can operate at

temperature up to 200°C and at pressure rate up to 15,000 psi. The complete system includes a

density measuring cell, a control station and a thermostatic bath.

FEATURES

Model: Anton Paar DMA HPM


Pressure range: up to 1000 bar (15,000 psi)

Density range: 0 to 3 g/cm3

Accuracy: ±10−3 g/cm3

Fittings: 1/8”

Wetted material: Hastelloy



VINCI TECHNOLOGIES


Phone: 331 41 37 92 20 Fax: 331 41 37 04 76



FL

UID

AN

AL

YS

IS

Compositi onal anal ysis

HYDROCARBON COMPOSITIONAL ANALYSER

Following the flash of the live fluid sample to ambient conditions in the gasometer,

compositional analysis of residual hydrocarbon liquid and evolved gas phase is conducted using

gas chromatography (GC). Two standard Gas Chromatographs are used to analyse the

composition of the gaseous and liquids fractions of the sample. The values obtained from the

two GC are used to generate compositional PVT reports of the sample including separator gas,

separator liquid and recombined sample.

FEATURES

Natural gas analyzer for wet gas analysis up to C14 based on the standard GPA 2286.

Liquid analyzer for crude oil and condensates analysis up to C36+ .

A chemstation for the two chromatographs

Reporting facilities to produce the PVT reports of separator gas, separator liquid and recombined

samples

Cryette for molecular weight determination

Gasometer with GOR apparatus

BENEFITS

Hydrocarbons analysis up to C36

Weight %, mole %, volume % provided

Molecular weight and distribution up to C36

Reporting facilities provided


VINCI TECHNOLOGIES


Phone: 331 41 37 92 20 Fax: 331 41 37 04 76



FL

UID

AN

AL

YS

IS

MOLECULAR WEIGHT TESTER

Automatic cryoscope for molecular weight, solution concentration, and freezing point

depression determinations for aqueous and various solvent solutions for 2.0 ml samples. It

features a digital readout in millidegrees Celsius of freezing point depression. The adjustable

bath temperature allows optimum temperature settings for particular solvent.

FEATURES

Cell temperature range: −6 to +26°C

Operation: Automatic or manual

Speed: 2 minutes per measurement

Precision temperature: 0.001°C, 1S.D. depends of solvent used

Precision molecular weight: 1% typical, depends of solvent used

Calibration: Two non interacting controls

Bath: 55 ml 15 minute cool down from ambient temperature

Power: 230 V 50/60Hz

Weight: 13.6 kg

Dimensions (mm): 35.5 x 20.3 x 25.4 cm


VINCI TECHNOLOGIES


Phone: 331 41 37 92 20 Fax: 331 41 37 04 76



FL

UID

AN

AL

YS

IS

Asphaltenes and waxes studi es

FLOW ASSURANCE SYSTEM (FLASS)

The Flass analyser allows for complete oil PVT studies and a variety of asphaltenes and wax

solid deposition experiments including constant mass expansion, differential vaporisation,

separator test, swelling tests, isothermal depressurization and isobaric temperature decrease

experiments, titration experiments, bulk filtration tests, particle size distributions and solids

onset determinations. The system features a PVT cell set up so that CME, bubble point and PVT

experimentation on oil sample is possible. It also includes a Solid detection system used to

detect when the organic deposition takes place. A High pressure microscope permits to visualise

accurately the Wax and Asphaltenes precipitation at onset conditions, identify the solid particles

and monitor the change in size and morphology of Wax crystals and Asphaltenes solids as

function of temperature, pressure, time and effect of various chemical treatments. The amount

of solids formed in the fluid sample when altering the pressure, temperature or composition of

the fluid can also be determined using the HP HT organic solid filtration system.

FEATURES


Temperature range: Ambient to 200°C (cooling option: -20°C)

Volume: up to 200 cc

Wetted material: Stainless steel, sapphire.

House software for particle size distribution and light absorbtion measurement.

BENEFITS

Multi analysis system ( Phase behaviour studies and complete solid deposition experiments)

Full description of the asphaltenes precipitation (pressure, temperature, growth, morphology,..)


VINCI TECHNOLOGIES


Phone: 331 41 37 92 20 Fax: 331 41 37 04 76



FL

UID

AN

AL

YS

IS

RESERVOIR FLUID PARTICLE ANALYSER (RFP)

The RFP analyser allows for a variety of asphaltenes and wax solid deposition experiments

including isothermal depressurization and isobaric temperature decrease experiments, titration

experiments, bulk filtration tests, particle size distributions and solids onset determinations. It

can visualise accurately the Wax and Asphaltenes precipitation at onset conditions, identify the

solid particles and monitor the change in size and morphology of Wax crystals and Asphaltenes

solids as function of temperature, pressure, time and effect of various chemical treatments. It

can also detect when the organic deposition takes place using a solid detection system with laser

source. An organic solid filtration system is added to determine the amount of solids formed in

the fluid sample when altering the pressure, temperature or composition of the fluid.

FEATURES

Pressure: Up to 20,000 psi

Temperature range: −30 to 200°C (400°F)

Mixer accumulator: 100 ml

Stirring mechanism: Magnetic mixer

Electrical: 220 VAC 50/60 Hz 1 phase

HPM system:

Particle size detection 0.2 µm

Microscopic zoom: x5000

House software for particle size distribution measurement

SDS system:

Wavelength Near infrared

Laser power: 250 mWatts

Detector sensitivity: 1 pWatt

Dynamic range: 100 dB

BENEFITS

Complete solid deposition experiments

Full description of the asphaltenes precipitation (pressure, temperature, growth,

morphology,..)

Very efficient mixing of the sample thanks to a magnetic driven stirrer inside the fluid

accumulator.


VINCI TECHNOLOGIES


Phone: 331 41 37 92 20 Fax: 331 41 37 04 76



FL

UID

AN

AL

YS

IS

HIGH PRESSURE MICROSCOPE (HPM)

The HPM is designed to visualise accurately the Wax and Asphaltenes precipitation at onset

condition up to 15,000 psi and 200°C. The HPM enables to identify the solid particles and

monitor the change in size and morphology of Wax crystals and Asphaltenes solids as function

of temperature, pressure, time and effect of various chemical treatments. The fluid under

consideration is homogenized at the desired conditions in the PVT cell and transferred from the

PVT cell to the HPM cell at controlled pressure and flow rate. The HPM cell assembly is

stabilised at the reservoir temperature and pressure. Subsequently the fluid is depressurized at

known pressure decrements, circulated into the HPM cell and any changes in the observed

character of the reservoir fluid are recorded in the HPM video camera. The provided software

measures the particle size distribution. The HPM can be delivered as a stand-alone system or an

add-on module to the Fluid Eval system.

FEATURES

Pressure range: Ambient to 15,000 psi


Particle size detection: from 0.2 µm

Wetted material: Stainless steel, sapphire.

Microscope zoom: up to x 5000

House software for particle size distribution measurement

BENEFITS

Can be connected to any End user’s PVT cell

Provides visual definition of the types of solids present in the sample

Permits to directly observe the onset and growth of organic solid precipitates at pressure and

temperature

Complete system provided with interpretation facilities


VINCI TECHNOLOGIES


Phone: 331 41 37 92 20 Fax: 331 41 37 04 76



FL

UID

AN

AL

YS

IS

SOLID DETECTION SYSTEM (SDS)

This device is designed to detect when the organic deposition takes place, in other words it

measures the onset conditions of live oil precipitation. The instrument is based on the

transmittance of a low intensity laser light through fiber optic transmission probes mounted

across a windowed cell. The instrument is composed of a laser windowed cell to connect the

high temperature optical fibers used to emit and receive the laser signal through the oil sample.,

an optic source to generate the signal crossing the fluid, a power meter to measure the

attenuated signal, two fiber optic transmission probes and a data acquisition software used to

record the system pressure, temperature, solvent flow rate and the power of the transmitted

light. The SDS can be used with different Vinci instruments such as Fluid Eval, Flass, FT700,..

FEATURES

Pressure: Up to 15,000 psi

Temperature range: Ambient to 200°C (400°F)


Wavelength: Near infrared



BENEFITS

Extreme accuracy at high pressure and temperature

Sample is always at pressure and temperature during experiment


VINCI TECHNOLOGIES


Phone: 331 41 37 92 20 Fax: 331 41 37 04 76



FL

UID

AN

AL

YS

IS

FLOCCULATION TITRIMETER (FT SERIES)

The FT series is designed to determine accurately the precipitation conditions of asphaltenes

and crystallisation conditions of waxes in very dark, undiluted crudes and oil products at high

pressure and high temperature. It is composed of a HP – HT stirred sample vessel combined to a

special optical probe which measures the transmittance of a low intensity laser light in the

sample. When asphaltene precipitation or wax crystallisation occurs, the transmittance of the

signal passing through the sample decreases sharply and it allows for determining the asphaltene

onset or the WAT in case of waxy oil.

FEATURES

Standard: ASTM D6703

Pressure: Up to 10,000 psi (option: 20,000 psi)

Temperature range: −20 to 200°C (400°F)

Vessel volume: 100 ml

Wetted parts: Stainless steel (option : Hastelloy)

Stirring mechanism: Magnetic mixer

Wavelength Near infrared





BENEFITS

Can detect solid particles in very low API oil sample.

Fully automated instrument

Very efficient mixing of the sample thanks to a magnetic driven stirrer inside the fluid

vessel


VINCI TECHNOLOGIES


Phone: 331 41 37 92 20 Fax: 331 41 37 04 76



FL

UID

AN

AL

YS

IS

AUTOMATED HEITHAUS FLOCCULATION TITRIMETER

(FT-A)

The computer-operated FT-A instrument is a stability diagnostic tool for quantifying the three

Heithaus compatibility parameters that estimate the colloidal stability of asphalts and asphalt

cross blends, aged asphalt, pyrolyzed asphalt, and heavy oil residuum. It is based on the ASTM

D6703 test method for automated Heithaus titrimetry. The samples of asphalt or heavy oil or

residuum are dissolved in toluene and titrated with iso-octane or n-heptane at controlled

temperatures to determine the point of flocculation and calculate the Heithaus compatibility

parameters.Compatibility influences important physical properties of these materials as well as

the formation of coke which causes fouling in refining processes.

FEATURES

Standard: ASTM D6703



Detection wavelength UV visible

Reaction vial volume: 30 ml

Circulation pump flow rate: up to 20ml/min

Titrant vessel volume: 30 ml

Titrant pump flow rate: up to 1 ml/min


Sample mixing: Magnetic type


BENEFITS

Fully automated apparatus

Rapid, accurate and reproducible data

Homogeneous temperature with no cold point


VINCI TECHNOLOGIES


Phone: 331 41 37 92 20 Fax: 331 41 37 04 76



FL

UID

AN

AL

YS

IS

ORGANIC SOLID FILTER (OSD 1000)

The organic solid filter is connected to the PVT cell and is used to determine the amount of

solids formed in the fluid sample when altering the pressure, temperature or composition of the

fluid. The instrument uses a filtration method to isolate and remove the solids from the fluid for

qualitative and quantitative analysis. Typically, the fluid sample is mixed with a solvent or

equilibrated at temperature or pressure sufficient to induce solid precipitation. The solids are

then isolated at temperature and pressure and brought to ambient conditions. The total mass of

precipitated solid is then measured. The solids are also analysed to obtain the property and

compositional information. The device is composed of a high pressure, high temperature

stainless steel filter holder using filter disc to retain the solid particles. The fluid sample is

transferred from the PVT cell to the floating piston accumulator through the filter at controlled

pressure and flow rate. Different ranges of filter size are given along with the filter.

FEATURES

Max pressure: 1000 bar (15,000 psi)

Max temperature: 200 °C


Filter size range (µm): 0.02 - 0.1 - 0.2 - 0.45 - 1 - 3 (pack of 50)

BENEFITS

Easy to dismount


VINCI TECHNOLOGIES


Phone: 331 41 37 92 20 Fax: 331 41 37 04 76



FL

UID

AN

AL

YS

IS

ASPHALTENE DESPOSITION LOOP (ASPHALTEVAL)

The asphalteval is a lab-scale circulating flow loop which is designed to measure asphaltene

deposition under realistic turbulent flowing conditions of production and transportation. Solid

deposits are measured using a solid detection system based on light scattering. Optional high

pressure microcopy facilities are also available and allow for taking pictures on live solid

particles. The pipe loop is designed to investigate the effects of temperature, pressure, flow

regime and shear rate on the deposition behavior of asphaltenes. The effect of additives can also

be assessed. The wetted parts can be made from stainless steel or hastelloy.

FEATURES

Working pressure…………… Up to 20,000 psi

Working temperature…………ambient to 200 °C

Deposition tube OD ….….….. 1 inch

Deposition tube length ….….. 2.5 meters

Fluid viscosity……………… 1-50 cP

Fluid density………………… 0.85-1.1 g/cc

Power supply…………………220 VAC 50/60 Hz 1 ph

Model 1: Stainless Steel Asphalteval:

Deposition tube ID ….….….. 0.562 inch

Flow rate…….……………….. up to 2.5 L/min

Max shear rate…….………… 145 s-1

Reynolds number…….……… 3344

Model 2: Hastelloy Asphalteval:

Deposition tube ID ….….….. 0.438 inch

Flow rate…….……………….. up to 2 L/min

Max shear rate…….………… 246 s-1

Reynolds number…….……… 3433

(assuming fluid density = 0.9 g/cc and viscosity = 1 cP)

BENEFITS

Mimick the process of asphaltene deposition from live reservoir fluids under realistic

production and transportation conditions.

Use of a very low shear rate pump to avoid solid deposition in the pump.


VINCI TECHNOLOGIES


Phone: 331 41 37 92 20 Fax: 331 41 37 04 76



FL

UID

AN

AL

YS

IS

WAX DEPOSITION FLOW LOOP FOR STOCK OIL SAMPLE

(WAX-EVAL A)

The Wax Eval A has been designed to examine the effects of wax and paraffin precipitation

and deposition in pipelines in a laboratory flow loop using stock tank oil sample. The apparatus

provides fast, accurate and reliable results for research of inhibiting and dissolving agents or

quality control. The oil sample which can be untreated or treated with a wax inhibitor is

circulating in the loop using an injection pump and is pre-heated to a set temperature while the

cooling bath is cooling to its set temperature. The differential pressure and differential

temperature are monitored. The slopes of these two parameters versus time are used to evaluate

the efficiency the wax inhibitors.

FEATURES

Pressure: up to 100 psi,

Temperature: -20°C to +90°C

Sample volume: 500 cc

Test coil diameter: 1/8”

Test coil length: 2 meters

Flow rate: up to 50 ml/min

Material Stainless steel


BENEFITS

Very easy to use

Accurate measurement of flow, pressure and temperature


VINCI TECHNOLOGIES


Phone: 331 41 37 92 20 Fax: 331 41 37 04 76



FL

UID

AN

AL

YS

IS

SMALL SIZE WAX FLOW LOOP FOR LIVE OIL SAMPLE

(WAX-EVAL SS200)

The Wax-Eval SS200 is a small sized wax deposition loop that exposes live oil to a range of

heat fluxes and shear rates that would be expected in the flow line during actual production. It

allows for determining the wax appearance temperature WAT and the wax deposition rate. The

WAT defines the temperature below which viscosity increases and wax deposit. The wax

deposition rate defines the amount of wax which deposit on the wall versus time. The loop

involves four main steps, namely, the charging of the live oil, the thermal pretreatment of the

oil, the cooling and the ungelling. An optional restart test loop can be added to the system in

order to measure the gel strength or yield stress which is used for estimating the start up

pressure requirement for gelled oil in a shutdown pipeline. Experimental data obtained with the

Wax Eval are entered into a simulation software to get a representative model of the oil sample

which can be used for real pipeline application.

FEATURES

Deposition loop outside diameter 1/8 inch

Deposition loop length 2 meters

Gel strength coil inside diameter 7 mm

Gel strength coil length 12 meters

Pressure: 3,000 psi

Temperature: − 20°C to 120°C

Sample volume: 50 cc for WAT and 240cc for gel test

Flow rate: up to 300 ml/hour

Temperature accuracy: 0.1°C



BENEFITS

Automated test

Assess wax inhibitors

Generate representative model of the oil sample in real pipeline conditions


VINCI TECHNOLOGIES


Phone: 331 41 37 92 20 Fax: 331 41 37 04 76



FL

UID

AN

AL

YS

IS

MEDIUM SIZE WAX FLOW LOOP FOR LIVE OIL SAMPLE

(WAX-EVAL MS150)

Wax deposition inside tubular and pipelines reduces the effective flow area, increasing

the pressure drop and potentially causing complete blockage. Therefore, it is important

to fully understand the oil’s behaviour throughout the pressure and temperature path

from the formation to the production facilities. The Wax Eval MS 150 is a medium

sized wax deposition loop that exposes live oil to a range of heat fluxes and shear rates

that would be expected in the flowline during actual production. It involves four main

steps, namely, the charging of the live oil, the thermal pretreatment of the oil, the

cooling and the ungelling. It enables to determine the WAT of the oil sample, assess

efficiency of inhibitors, and estimate the wax deposition rate according to flow

conditions. It also enables to calculate pigging frequency and pipeline restart pressure

for gel breaking. Experimental data obtained with the Wax Eval are entered into a

simulation software to get a representative model of the oil sample which can be used

for real pipeline application.

.

FEATURES

Deposition loop outside diameter 1 inch

Deposition loop length 16 meters

Gel strength coil outside diameter 3/8”

Gel strength coil length 16 meters

Pressure: 2,175 psi (150 bar)


Sample volume: 40 Litres

Flow rate: up to 300 L/hour



Power supply: 380-400 VAC 50 Hz 3 ph

BENEFITS

Representative of pipeline conditions

Assess wax inhibitors

Generate representative model of the oil sample in real pipeline conditions


VINCI TECHNOLOGIES


Phone: 331 41 37 92 20 Fax: 331 41 37 04 76



FL

UID

AN

AL

YS

IS

MULTI-PLACE COLD FINGER (MFC 6)

The cold finger apparatus uses a rapid screening method to identify and rank potential wax

deposition inhibitors. The quantity of paraffin wax adhering to the cooled surface is quantified.

The efficiency of scale inhibitors can be assessed. The MCF 6 apparatus is designed to be used

with black oil samples held in six glass bottles. Those are maintained at constant temperature

during the tests in a thermal controlled bath. The fingers immersed in the oil samples are then

cooled to a predefined minimum temperature via coolant supplied by an external chiller bath to

induce a temperature gradient in the sample. The samples are then run for 24 hours with

periodic weight measurement of the finger to determine potential for deposition. After the

experiment, deposited wax is collected and composition can be further analyzed. Deposited wax

is removed by heating the finger and washed with solvent.

FEATURES

Number of sample bottles: 6


Temperature of oil: ambient to 60°C

Temperature of cold finger: -10°C to 60°C

Temperature difference between cold finger and oil .Up to 20°C

Temperature difference between two cold fingers Up to 20°C

Stirrer speed: 100 to 1,000 rpm

Sample volume required: 100 cc

Temperature control: 1 temperature sensor per cold finger

Power supply: 220 VAC 50 Hz or 220 VAC 60 Hz

BENEFITS

Fully automated

Parallel measurements

Temperature ramp and variable stirring speed available

Individual temperature control on each cold finger


VINCI TECHNOLOGIES


Phone: 331 41 37 92 20 Fax: 331 41 37 04 76



FL

UID

AN

AL

YS

IS

FLOW-THROUGH SDS CELL (FTC SERIES)

The FTC series cells are designed to be used with the Vinci SDS system to measure solid

deposits such as asphaltenes and wax under realistic flowing conditions, i.e. pressure,

temperature and shear. The cells are mostly used in deposition flow loops to investigate the

effects of flow rate, inhibitor concentration, temperature and pressure on solid deposition. The

cell consists of a high pressure hollow cylinder equipped with inlet and outlet axial ports to let

the fluid flow and two lateral ports to mount the optical fibers of the SDS system.

FEATURES

Model Pressure

psi

Wetted parts OD

inch

ID

inch

FTC-3-SS-8 3,000 Stainless steel 1/8 0.069



FTC-3-SS-1 3,000 Stainless steel 1 0.834

FTC-3-HC-8 3,000 Hastelloy 1/8 0.085

FTC-3-HC-4 3,000 Hastelloy 1/4 0.194

FTC-3-HC-2 3,000 Hastelloy 1/2 0.402

FTC-3-HC-1 3,000 Hastelloy 1 0.834





FTC-10-HC-8 10,000 Hastelloy 1/8 0.069

FTC-10-HC-4 10,000 Hastelloy 1/4 0.152



FTC-20-HC-4 20,000 Hastelloy 1/4 0.083

FTC-20-HC-1 20,000 Hastelloy 1 0.438

Temperature range: -20°C to +200°C

BENEFITS

Unique device for deposit detection under flowing conditions

Small sized cell which can be easily installed in a set –up


VINCI TECHNOLOGIES


Phone: 331 41 37 92 20 Fax: 331 41 37 04 76



FL

UID

AN

AL

YS

IS

HIGH PRESSURE ROTARY VANE FLOW METER (RVF

SERIES)

The high pressure RVF series flow meter features a radial vaned impeller, mounted on a vertical

spindle within a measuring chamber. The flowing fluid causes the impeller blades to rotate at a

speed directly proportional to flow rate. The rotating impeller is magnetically coupled to a

register and each impeller rotation is counted and converted into volumetric unit. The device is

provided with an electronic totalizer which can display flow rate and also be hooked-up to a

computer.

FEATURES

Wetted parts: Titanium or Inconel

Inlet and outlet connections: 1 inch

Maximum Pressure: up to 5,000 psi

Min flow rate: 500 ml/min

Max flow rate: 50,000 ml/min

Accuracy: +/- 3,% of reading

Fluid viscosity: up to 100 cP


Impeller wetted part: Peek

Gasket material: Viton

Weight: 1 kg

Power: 110-220 VAC, 50/60 Hz

E&P LABORATORY APPLICATION

Measure fluid flow in deposition loops which can be used to regulate flow rate of

recirculation pumps

BENEFITS

Flow measurement is not affected by solid particles present in the fluid.

Corrosion free wetted part

Can be operated with any liquids under extreme pressure and temperature conditions


VINCI TECHNOLOGIES


Phone: 331 41 37 92 20 Fax: 331 41 37 04 76



FL

UID

AN

AL

YS

IS

FLOOR STAND STIRRED PRESSURE VESSEL (FSV SERIES)

The FSV series vessel is specifically designed to stir large volume of fluid under pressure and

temperature. The vessel consists of a cylindrical metal chamber equipped with a bolted sealed

head and a manual bottom drain valve. It features an internal heavy duty stirring system, made

of a motor drive magnetically coupled to an internal stirrer shaft with attached anchor for

stirring viscous liquids. The head is provided with one hand operated valve, a thermocouple for

measuring the temperature within the vessel, a pressure gauge and a safety burst disc. A control

panel controls the motor speed drive for stirrer. Temperature and pressure transducers can be

interfaced to the panel if there are needed. The unit can also be interfaced to a computer for

remote control. The complete vessel is mounted on an easily moveable trolley with an optional

chain pulley lifting system for lifting the head with minimum effort.

FEATURES


Stirring speed: up to 200 RPM

Fluid viscosity: 10,000 cP

Gasket material: Viton

Inlet and outlet connections: 1inch (other upon request)

Power: 110-220 VAC, 50/60 Hz

E&P LABORATORY APPLICATION Store live oil fluid for large scale deposition loops

BENEFITS

Can stir a large volume of liquid under extreme pressure and temperature conditions

Heavy duty magnetic driven stirrer drive

Corrosion free wetted parts

Model Volume (liter) Presssure (psi ) Wetted parts Weight (kg)

FSV 50-30-S 50 3,000 Stainless steel 350

FSV 50-30-H 50 3,000 Hastelloy 650


http://www.amarequip.com/wp-content/uploads/2014/06/Autoclave-trolley-1.jpg

VINCI TECHNOLOGIES


Phone: 331 41 37 92 20 Fax: 331 41 37 04 76



FL

UID

AN

AL

YS

IS

Hydrates studi es

GAS HYDRATES AUTOCLAVE SYSTEM (GHA SERIES)

The GHA series is a mercury free cell designed to (1) study gas hydrate formation and

dissociations, (2) measure the induction time for formation of hydrates by monitoring the

pressure drop as a function of time during hydrate formation and (3) take video pictures during

the experiments. The system consists of a constant volume hydrate cell with a 250 cc volume

and pressure rating up to 3,000 psi. The cell temperature is controlled by a thermostatic bath. A

thermocouple measures the temperature of the cell with an accuracy of 0.1°C. The cell pressure

is monitored by a pressure transducer. A magnetic stirrer with adjustable rotation speed is used

to agitate the test fluids. A computer is used for data acquisition of temperature and pressure

versus time. The cell is also equipped with a stethoscopic camera to take pictures.

FEATURES

Pressure: 3,000 psi,

Volume: 250 cc




Stirring mechanism: Magnetic drive

Stirring speed………………….. up to 1000 RPM


BENEFITS

Cost effective

Accurate measurement of pressure and temperature

Video image capturing that allows for later retrieval

Mercury free operations


VINCI TECHNOLOGIES


Phone: 331 41 37 92 20 Fax: 331 41 37 04 76



FL

UID

AN

AL

YS

IS

HYDRATES STUDIES SYSTEM (HYDREVAL)

The mercury free Hydreval™ analyser is designed for the determination of hydrates formation

and dissociation conditions as well as the evaluation of hydrates inhibitor. The instrument

provides four different methods to study hydrates phenomena: (a) isochoric method (constant

volume), isobaric method (constant pressure), isothermal method (constant temperature) and

visual method. The apparatus features a fully visual cell allowing for 360° visibility from top to

bottom of the sample, an embedded pump for volume and pressure control and a controlled

temperature airbath.

FEATURES


Volume: 60 cc







BENEFITS

Very easy to use and to maintain

Accurate measurement of volume, pressure and temperature

Full visibility


VINCI TECHNOLOGIES


Phone: 331 41 37 92 20 Fax: 331 41 37 04 76



FL

UID

AN

AL

YS

IS

HYDRATES KINETICS STUDIES SYSTEM (KINETIC-EVAL)

The kinetic-Eval analyser is used for studying the kinetics of gas hydrate formation by

measuring the induction time for formation of hydrates and measuring the hydrate growth rate

that occurs after nuclei are formed. It is also used for determining the hydrates composition and

evaluating kinetic hydrate inhibitors and other inhibitors such as anti agglomerant, emulsion,

natural inhibitors, salts. The system consists of a constant volume hydrate cell with a 250 cc

volume and pressure rating up to 5,000 psi. The cell temperature is controlled by circulating

coolant inside a constant temperature bath. A thermocouple measures the temperature of the cell

with an accuracy of 0.1°C. The cell pressure is monitored by a pressure transducer. A magnetic

stirrer with adjustable rotation speed is used to agitate the test fluids. The torque required to

drive the stirrer at a constant speed is measured and related to the viscosity of the system.

FEATURES


Volume: 250 cc






BENEFITS

Very efficient magnetic stirrer with torque measurement

Can be used to evaluate anti agglomerant inhibitors

Accurate measurement of torque, pressure and temperature



VINCI TECHNOLOGIES


Phone: 331 41 37 92 20 Fax: 331 41 37 04 76



FL

UID

AN

AL

YS

IS

FLUID-EVAL FOR HP- HT VISUAL STUDIES (BENCH TOP

VISUAL VERSION)

The bench top visual Fluid-Eval is mainly designed for the study of thermodynamic properties and

phase behaviour of multiphase sample such as black oil samples, gas condensates, gas hydrates and

supercritical fluids at reservoir conditions of pressure and temperature. It offers full visibility of the

sample during phase behaviour experiments. The system consists of a piston cell equipped with

pressure, temperature and volume measurement facilities, electrical heating system, high torque

magnetic driven stirrer and video camera to monitor through a front side sapphire window the

phase behaviour of the sample. The cell also features a cooling jacket connected to a cooling

bath to keep the sample at sub-ambient temperature. A high pressure pump is also provided to

keep the sample at the test pressure.

FEATURES


Volume: 100 cc






BENEFITS

Very efficient magnetic stirrer with torque measurement

Full visibility of the sample during experimental test



VINCI TECHNOLOGIES


Phone: 331 41 37 92 20 Fax: 331 41 37 04 76



FL

UID

AN

AL

YS

IS

Scal e depositi on studi es

DYNAMIC SCALE LOOP (SCALEVAL)

The Scaleval apparatus is designed to study the precipitation and deposition of scale at reservoir

and pipeline conditions of pressure and temperature. It is used to evaluate the efficiency of

chemical inhibitors to prevent the formation of mineral scales such as calcium carbonate,

calcium barium and barium sulfates. It allows to determine the minimum inhibitor concentration

(MIC) required to prevent the deposition of scale and to perform comparative tests with

different inhibitors in the same conditions. The system uses the principle of the tube blocking

test which is an industry practice, to evaluate the minimum inhibitor concentration (i.e. MIC) in

dynamic flow conditions at required temperature. Inhibitor efficiency is measured by the ratio

of the time needed to block the tube in the presence of inhibitor divided by the time needed to

block the tube without inhibitor.

FEATURES


Temperature: up to 150°C

Fluid flow rate up to 10 cc/min




BENEFITS

Fully automated test

Can be used to evaluate scale inhibitors

Dynamic test which simulates pipelines conditions


VINCI TECHNOLOGIES


Phone: 331 41 37 92 20 Fax: 331 41 37 04 76



FL

UID

AN

AL

YS

IS

Brine crystallization temperature

PRESSURIZED BRINE CRYSTALLIZATION TESTER

(PCT1300)

The automated PCT 1300 instrument is designed to measure the crystallization temperature of a

pressurized brine fluid under conditions involving a combination of high pressure and low temperature. It

features a very sensitive optical light detector for detecting crystals in the fluid sample, thus eliminating

the need for a person to visually observe the sample for the presence of crystal when measuring the

crystallization events FCTA, TCT and LCTD of a brine sample. The apparatus comprises a high-pressure

cell for containing a brine fluid sample. A magnetic driven stirrer, located inside the cell, ensures a good

mixing of the sample and a temperature sensor measures the temperature of the brine sample during the

test. The cell features a double jacket to circulate the cooling fluid from the cooling bath. A high-pressure

pump is used for pressurizing the fluid sample.

FEATURES

Pressure: up to 20,000 psi

Temperature: -20 to 60°C

Sample volume: 100 ml

Stirring mechanism: magnetic mixer


Wetted part: Hastelloy

Power supply: 110-220 VAC 50/60 Hz

BENEFITS

Provides highly accurate and reproducible crystallization temperature measurements

Automated set up


VINCI TECHNOLOGIES


Phone: 331 41 37 92 20 Fax: 331 41 37 04 76



FL

UID

AN

AL

YS

IS

Emulsions

EMULSION PRESSURE DROP LOOP (EMULSEVAL)

The Emulseval is specially designed to determine pipeline flow properties of water in oil emulsions at

different aqueous phase volume fractions and at various flow rate and temperature conditions. It exposes

the emulsion to a range of heat fluxes and shear rates that would be expected in the pipeline during actual

transportation. It basically measures the pressure drop along the pipeline section so as to derive the

pressure gradient for a given formation of water-oil emulsion.

FEATURES

Pipeline outside diameter 1 inch

Pipeline inside diameter 0.87 inch

Pipe line length 3 meters

Pressure: 200 psi

Temperature: ambient to 90°C

Sample volume: 25 Litres

Flow rate: up to 90 L/min

Reynold’s number: 90,000

Shear rate: 1,450 s-1



Power supply: 380-400 VAC 50 Hz 3 ph

BENEFITS

Easy to use

Provided with a low shear pump


VINCI TECHNOLOGIES


Phone: 331 41 37 92 20 Fax: 331 41 37 04 76



FL

UID

AN

AL

YS

IS

Fluid pumpability

FRICTION FLOW LOOP FOR EVALUATING DRAG REDUCING

AGENTS (DRA FLOW LOOP)

The DRA flow loop enables the end user to test, quantify and evaluate the performance of a

friction reducer by measuring frictional pressure loss of a fluid flowing in a pipe in turbulent

flow. The effect of friction reducers on both flow rate and pressure are analyzed and reported.

The apparatus provides fast, accurate and reliable results for research of friction reducers. The

system circulates test fluid through two test sections of various diameters to generate differential

pressure versus flow rate data. The test fluid injection system comprises a mixing tank to fully

mix additives into the test fluid and a low-shear pump for injection of test fluids with the flow

rate controlled by a Coriolis flow meter. High-accuracy differential pressure transducers are

provided for each tubing diameter for multiple data readings per test. Additives can be injected

into the flow stream via a metering pump or added directly into the mixing tank. Differential

pressure, pressure, temperature, flow rate and Reynolds number are computed in real time. The

system can be operated in open and closed modes. It is easy to set up, operate, clean, maintain

and calibrate. It also offers flush-and-fill automation for easy system clean up.

FEATURES

Working pressure……………. up to 150 psi

Working temperature………… 10°C to 40 °C

Reynolds Number…………….. up to 150,000

Tank volume…….……………. 200 liters

Flow rate…….……………….. 8 to 50 liters /min

Differential pressure range ….. 0-100 psi

Loop n°1 external diameter…… 3/4”

Loop n°1 internal diameter……. 0.607”

Loop n°1 length…….………… 3 meters

Loop n°2 external diameter…… 1/2”

Loop n°2 internal diameter……. 0.403”

Loop n°2 length…….…………. 3 meters

Wetted material………………… Stainless steel

Power supply…………………… 220 VAC 50/60 Hz 1 ph

BENEFITS

Easy to use

Provided with automated functions


VINCI TECHNOLOGIES


Phone: 331 41 37 92 20 Fax: 331 41 37 04 76



FL

UID

AN

AL

YS

IS

Rheology

HIGH PRESSURE RHEOMETER (RHEO 1000)

The RHEO 1000 is a computer-controlled rotational rheometer based on Taylor-Couette flow,

which is specifically designed to measure the rheology properties of a live oil sample at various

conditions of pressure, temperature, chemical composition and shear rate. It can simultaneously

mimic the deposition process of wax/asphaltene according to real production shear conditions

while measuring the rheological properties of the sample. The instrument provides fruitful

information when used with petroleum fluids containing either solid waxes or asphatene

particles. Those fluids deviate from Newtonian to non-Newtonian behaviour as soon solid

particles precipitate in the fluid. Such precipitation has a tremendous impact of the rheological

behaviour of the oil. It becomes then necessary to characterize the fluid when it exhibits non-

Newtonian behaviour with experimental test under true conditions of pressure, temperature and

shear rate. The Rheo 1000 is the perfect tool to accomplish this task.

FEATURES



Viscosity range: up to 100 Pa s (i.e 100,000 Cp)

Shear rate range: up to 10 000 sec-1

Sample volume: 50 ml

Rotor speed range: up to 1,500 rpm

Operating mode: controlled shear rate

Wetted part: Monel


BENEFITS

Fully automated apparatus

Rapid, accurate and reproducible data

Determine rheological properties and onset conditions of live oil precipitation


VINCI TECHNOLOGIES


Phone: 331 41 37 92 20 Fax: 331 41 37 04 76



FL

UID

AN

AL

YS

IS

Sampling

PVT SURFACE SEPARATOR SAMPLING KIT

The surface sampling kit includes a set of tools that allows the operator to take surface liquid

and gas samples from the test separator. Samples of the separation fluids are taken

simultaneously for laboratory recombination to produce representative reservoir fluid for

subsequent simulation study work. It is provided with a transportable glass fiver box and

consists of:

- 2 flexible hoses to connect the oil and gas cylinders to the separator

Features:

Maximum pressure: 350 bar

Maximum temperature: 90°C

Length: 2 m

- 1 set of connector adaptors including:

5 sets of connection adapters per size for oil cylinder with the following sizes: 1/8” LP,

¼” MP, ¼” HP, ¼” NPT

5 sets of ½” NPT connection adapter for separator

5 sets of type E connection adapter for gas cylinder.

- 1 manifold to connect the hose to the oil cylinder. It includes the manometer (0-350 bar) to

measure the separator oil pressure and the isolating valve for the vacuum pump.

- 1 manifold to connect the hose to the gas cylinder. It includes the manometer (0-200 bar) to

measure the separator gas pressure and the isolating valve for the vacuum pump.

- 1 vacuum pump to vacuum the sample cylinder with manometer (0-1 bar), 1 meter hose and

quick connector.

- 1 set of tools

- 1 temperature sensor with control device to measure the temperature of the separator

- 1 500 cc graduated burette to determine the volume of transferred oil with manometer (0-350

bar) and isolating valve.

- one labelling facilities including one crimper, 1000 leadings, 2 sets of 10 meter leading wire

rolls, 200 green labels marked “EMPTY”, 200 red labels marked “FULL”

- 1 heavy-duty carrying case to store all the previous components.


VINCI TECHNOLOGIES


Phone: 331 41 37 92 20 Fax: 331 41 37 04 76



FL

UID

AN

AL

YS

IS

BOTTOM HOLE SAMPLER

The bottom hole sampler is to be used with slick wire line for trapping representative sub-

surface oil and gas samples at reservoir conditions for PVT analysis. It is designed to recover

reservoir samples from the well. The tool consists of an air chamber, a reservoir oil chamber, a

mechanical operated clock system, a triggering system, a hanging head and a closing

mechanism. The system comes complete with the sampling tool, the transportation box and the

service kit.

The sampler has to be put in the reservoir. When the clock mechanism is reaching zero, the

reservoir fluid enters slowly in the oil chamber by displacing hydraulic oil. The filling is slow

enough in order not to flash the sample. Once the chamber is completely filled up with the oil

sample, the sample chamber is sealed automatically. The sampler can be pulled out from the

well to the surface. The oil sample can be conveniently transferred from the sampler into the

shipping bottle using the mobile transfer bench.

FEATURES

Type………………………………..…Positive displacement system (i.e. PDS)

Max Working temperature………….. 200°C / 400° F

Max Pressure………………………… 15,000 psi

Volume …………………………..… 600 cc

Wetted material…………………….. Stainless steel (H2S, sour gas resistant), titanium and brass alloy

Weight……………………………… 30 kg

Outside diameter..… ……………….43 mm

Length ……………………………… 3.71 meters

Clock running time………………….. 5 hours, other time upon request

BENEFITS

Mercury free

Light and compact


VINCI TECHNOLOGIES


Phone: 331 41 37 92 20 Fax: 331 41 37 04 76



FL

UID

AN

AL

YS

IS

TRANSFER BENCH

The transfer bench is designed to transfer fluid sample from down-hole sampler to piston type

sample cylinder at site location. After the sample has been transferred, the determination of the

bubble point pressure can be performed for sample validation. The apparatus comes complete

with hydraulic transfer pump, transfer and control valves, two precision gauges, valves, fittings,

connections, accessories kit and stainless steel transportation box. All valves are accessible from

the front side. The sampler is positioned horizontally in clamps above the rear and the sample

cylinder to one side. A set of accessories including all the hoses and attachment necessary to the

transfer operation.

FEATURES

Max Working pressure…………..…15,000 psi (1,000 bar)

Max Working temperature…………..150°C

Pressure accuracy ………………..…0,1 % FS

Wetted material……………………..Stainless steel

Weight………………………………42 kg

Dimensions (HxWxL)..…………….450 mm x 430 mm x 340 mm

Fluid ………………………………. Glycol, 2/3 water

Recommended air pressure…..…… 100 psi

BENEFITS

Transportation casing easy to stack

Light and compact


VINCI TECHNOLOGIES


Phone: 331 41 37 92 20 Fax: 331 41 37 04 76



FL

UID

AN

AL

YS

IS

HIGH PRESSURE PISTON SAMPLE CYLINDER

(HPP SERIES)

The HPP series sample cylinder is a double end piston type cylinder for safe transportation of

the reservoir fluid to the laboratory. The sample fluid is isolated from the secondary driving

fluid with a floating piston especially designed to minimize friction and reduce pressure load.

The piston accommodates a mixing ball with a minimum of dead volume. All bottles are

furnished with a single inlet needle valve for driving fluid and a double inlet needle valve for

sample fluid. On the sample side, there is also incorporated an evacuation port nipple and plug.

Valves installed at either end of the bottle are protected by valve guards from damage during

handling. A carrying case is also available for transportation purposes. The cylinder can be

made from stainless steel or titanium.

FEATURES

Model Volume

ml

Pressure

psi

Temp.

°C

Weight

Kg

Length

mm

Diameter

mm

Material Thread

connection

HPP 700-10 700 10,000 150 17 705 88 SS ¼ “ FNPT

HPP 1000-10 1,000 10,000 150 19 800 88 SS ¼ “ FNPT

HPP 700-15 700 15,000 150 23 825 88 SS / Ti 1/8” FLP

HPP 1000-15 1,000 15,000 150 27 970 88 SS / Ti 1/8” FLP

HPP 700-20 700 20,000 150 29 945 88 SS / Ti ¼” FHP

HPP 1000-20 1,000 20,000 150 36 1150 88 SS / Ti ¼” FHP

BENEFITS

H2S resistant

Sample agitation ball mixer

Safe operation

Minimum dead volume

Mercury free


VINCI TECHNOLOGIES


Phone: 331 41 37 92 20 Fax: 331 41 37 04 76



FL

UID

AN

AL

YS

IS

MICRO HIGH PRESSURE PISTON SAMPLE CYLINDER

(MHP SERIES)

The MHP series sample cylinder is a small volume piston type cylinder for safe transportation

of the reservoir fluid to the laboratory. The sample fluid is isolated from the secondary driving


The piston accommodates a mixing ring with a minimum of dead volume. All bottles are

furnished with a single inlet needle valve for driving fluid and a single inlet needle valve for

sample fluid. Valves installed at either end of the bottle are protected by valve guards from

damage during handling. A carrying case is also available for transportation purposes.

FEATURES

Model Volume

ml

Pressure

psi

Temp.

°C

Weight

Kg

Length

mm

Diameter

mm

Material Thread

connection

MHP 50 50 15,000 150 2 300 50 Stainless Steel 1/8” FLP



BENEFITS

H2S resistant

Sample agitation ring mixer

Safe operation

Minimum dead volume

Mercury free


VINCI TECHNOLOGIES


Phone: 331 41 37 92 20 Fax: 331 41 37 04 76



FL

UID

AN

AL

YS

IS

LIGHT WEIGHT PISTON SAMPLE CYLINDER (CYLIGHT SERIES)

The cylight series cylinder is a very light weight titanium double end piston type cylinder for

safe transportation of the reservoir fluid. The sample fluid is isolated from the secondary driving


The piston accommodates a mixing ball with a minimum of dead volume and can be used for

agitation during determination of bubble point. The bottle is furnished with a single inlet valve

for driving fluid and a double inlet needle valve for sample fluid. A carrying case is also

available for transportation purposes.

FEATURES

Model Volume

ml

Pressure

psi

Temp.

°C

Weight

Kg

Length

mm

Diameter

mm

Material Thread

connection

CYLIGHT 300 300 10,000 150 5 300 70 Titanium 1/8’’ FLP



BENEFITS

Very light and compact

H2S resistant


Safe operation

Minimum dead volume

Mercury free


VINCI TECHNOLOGIES


Phone: 331 41 37 92 20 Fax: 331 41 37 04 76



FL

UID

AN

AL

YS

IS

SINGLE PHASE SAMPLE CYLINDER (SPS SERIES) The single-phase sample bottle is designed for monophasic PVT sample transportation, keeping

the sample at reservoir pressure or above, all the way to the laboratory. The cylinder uses a

pressure compensation end cap and a large mass profiled agitation ring to agitate the sample

during bubble point determination. All bottles are furnished with a single inlet needle valve for

driving fluid, a single inlet needle valve for the nitrogen gas cap and a double inlet needle valve

for sample fluid. On the sample side, there is also incorporated an evacuation port nipple and

plug. Valves installed at either end of the bottle are protected by valve guards from damage

during handling. A carrying case is also available for transportation purposes.

FEATURES

Model Volume

ml

Pressure

psi

Temp.

°C

Weight

Kg

Length

mm

Diameter

mm

Material Thread

connection

SPS 700-10 700 10,000 150 27 850 88 Stainless Steel ¼ “ FNPT

SPS 700-15 700 15,000 150 33 1020 88 Stainless Steel ¼” FMP

SPS 700-20 700 20,000 150 39 1300 88 Stainless Steel ¼” FHP

BENEFITS

H2S resistant

Single phase sample sample transportation

Sample agitation ring mixer

Minimum dead volume

Safe operation


VINCI TECHNOLOGIES


Phone: 331 41 37 92 20 Fax: 331 41 37 04 76



FL

UID

AN

AL

YS

IS

LOW PRESSURE PISTON SAMPLE CYLINDER

(LPP SERIES) The LPP series sample cylinder is a double end piston type cylinder for storage and

transportation of the surface fluid to the laboratory. The sample fluid is isolated from the

secondary driving fluid with a floating piston especially designed to minimize friction and

reduce pressure load. The bottle is equipped with an external magnetic volume tracker. The inlet

and pre charge valves are provided with safety burst discs and pressure indication gauges. The

piston accommodates a mixing ball with a minimum of dead volume. A carrying case is also

available for transportation purposes.

FEATURES

Model Volume

ml

Pressure

psi

Temp.

°C

Weight

Kg

Length

mm

Diameter

mm

Material Thread

connection

LPP 100 100 3,000 120 4 490 50 Stainless Steel ¼ “ FNPT




BENEFITS

H2S resistant


Volume indicator

Safe operation

Minimum dead volume

Mercury free


VINCI TECHNOLOGIES


Phone: 331 41 37 92 20 Fax: 331 41 37 04 76



FL

UID

AN

AL

YS

IS

FLOW THROUGH SAMPLE CYLINDER (FTS SERIES)

The FTS series sample cylinder is a flow through cylinder for storage and transportation of low

pressure gas and oil sample. The cylinder is provided with two needle valves, one manometer

and one safety burst disc. Carrying case is optional.

.

FEATURES

Model Volume

ml

Pressure

psi

Temp.

°C

Weight

Kg

Length

mm

Diameter

mm

Material Thread

connection

FTS 150 SS 150 2,800 200 2 300 50 Stainless steel ¼ “ FNPT

FTS 150 T 150 2,800 200 2 300 50 Teflon coated ¼ “ FNPT





BENEFITS

H2S resistant

Safe operation


VINCI TECHNOLOGIES


Phone: 331 41 37 92 20 Fax: 331 41 37 04 76



FL

UID

AN

AL

YS

IS

GAS SAMPLE CYLINDER (GS SERIES)

The gas shipping bottle is designed to transport and store pressurized gas samples such as those

in the petroleum industry. The standard bottle has a capacity of 20 liters at pressure up to 3,000

psi. Construction material is aluminium. All standard bottles are furnished with one angle

needle valve at each end. Valves are protected by valve guards from damage during handling. A

carrying case is also available for transportation purposes.

FEATURES

Capacity: 20 litres

Working temperature: −10 to 100 °C

Filling pressure: 200 bar (2,900 psi) @ 60°C

170 bar (2,465 psi) @ 100°C

Construction: Cylinder: Aluminium

Valves: Stainless steel

Thread Connection: ¼” FNPT

Dimensions OD x L: 25 x 99 cm

Weight: 26 Kg

BENEFITS

Transportation casing easy to stack

Light weight

Compliant with international regulation

H2S resistant


VINCI TECHNOLOGIES


Phone: 331 41 37 92 20 Fax: 331 41 37 04 76



FL

UID

AN

AL

YS

IS

FLOATING PISTON ACCUMULATOR (FPA SERIES)

The floating piston accumulators are available in a range of different volume and pressure

rating. These can be constructed in different material such as 316 stainless steel, titanium or

hastelloy. The fluid seals use standard Viton ‘O’ rings and back up ring.

FEATURES

Pressure: 5,000 psi, 10,000 psi or 15,000 psi


Cell volume: 100 cc, 300 cc, 500 cc, 700 cc, 1,000 cc, 2,000 cc, 5000 cc

Material: 316 stainless steel, titanium or hastelloy


VINCI TECHNOLOGIES


Phone: 331 41 37 92 20 Fax: 331 41 37 04 76



FL

UID

AN

AL

YS

IS

Sample pr eparation

MIXER CYLINDER (MC SERIES)

The MC series are double end piston type cylinders designed to store and mix any kind of fluids

at pressure and temperature. The sample fluid is isolated from the secondary driving fluid with a

floating piston and a magnetic mixer is located in the mixing sample chamber for proper

agitation. The mixer is magnetically coupled to a drive system through the accumulator end cap

which incorporates a permanent magnet driven by a direct current motor with variable speed. A

mixer controller permits to stop, start and control the speed of the mixer. The cylinder can be

operated in either upright or inverted orientation. Both end caps are provided with an inlet/outlet

port for fluid introduction or fluid sampling.

FEATURES

Model Volume

ml

Pressure

psi

Temp.

°C

Weight

Kg

Length

mm

Diameter

mm

Material

(1)

Thread

connection

MC 500-10 500 10,000 150 21 700 120 Stainless steel ¼” FNPT

MC 1000-10 1,000 10,000 150 25 750 120 Stainless steel ¼” FNPT

MC 2000-10 2,000 10,000 150 35 900 150 Stainless steel ¼” FNPT

MC 500-15 500 15,000 200 21 700 120 Stainless steel 1/8” FLP

MC 1000-15 1,000 15,000 200 25 750 120 Stainless steel 1/8” FLP

MC 2000-15 2,000 15,000 200 35 900 150 Stainless steel 1/8” FLP (1) Titanium material available.

Mixer controller

Power requirement…………………… 230 VAC, 50 Hz, 100 W

BENEFITS

H2S resistant

The impeller provides a minimum dead volume

Provide rigorous agitation of entire fluid sample

Capable of mixing high viscosity samples up to 1,000 cp

High speed, allows equilibrium to be reached in minimum time

Reduces operating time for establishing phase equilibrium on sample.


VINCI TECHNOLOGIES


Phone: 331 41 37 92 20 Fax: 331 41 37 04 76



FL

UID

AN

AL

YS

IS

RECOMBINATION CELL APPARATUS (RCA 1000)

The RCA 1000 instrument is based on a high pressure, high temperature recombination cell in

which oil and gas solutions are injected at pre-defined volume, stirred together, heated at a

desired temperature and pressurized at pressure above the saturation pressure for few hours to

give a homogeneous mixture of the reservoir fluid. The instrument comes with a recombination

cell jacketed with a heating mantel for temperature control, a magnetic driven stirrer, a

motorized rocking system with a mixing ring in the sample chamber of the cell for proper

agitation of heavy oil samples and a temperature and pressure display panel. The top of the cell

is equipped with a bull’s eye window to visualize the saturation pressure.

FEATURES

Cell Volume: 2,000 cc

Pressure: 15,000 psi (1,000 bar)

Max working temperature: Ambient to 175°C (350 °F)

Wetted material: Stainless steel, viton

Pressure accuracy: 0.1 % FS

Temperature accuracy: ± 0.5 °C


BENEFITS

Very fast recombination operation due to the magnetic driven stirrer

The motorized rocking system used in conjunction with the mixing ring enables an efficient

agitation of the heavy oil sample.

Bull’s eye window for dew point and bubble point detection

Versatile as it can be used for oil and gas condensates thanks to its rocking system


VINCI TECHNOLOGIES


Phone: 331 41 37 92 20 Fax: 331 41 37 04 76



FL

UID

AN

AL

YS

IS

MOBILE RECOMBINATION AND RESTORATION APPARATUS

(MRR 1000)

This apparatus is especially designed to physically recombine gas and liquid samples in

reservoir conditions of pressure and temperature. The apparatus comes with a recombination

cell jacketed in an insulated heating mantel for temperature control, a motorized rocking system,

a magnetic driven stirrer for proper agitation, a temperature and pressure display panel and a

moveable chassis. The apparatus is ideal for field application as it is provided with a

transportable box to be easy to move around from one site to another. The apparatus can be also

used as a restoration unit by replacing the recombination cell with a shipping cylinder. The

sample cylinder shall be wrapped with the heating mantle and then mounted on the motorized

rocking system to provide the mean to agitate the fluid under pressure and temperature for

several days, if required.

FEATURES

Cell Volume: 1,000 cc

Pressure: 15,000 psi (1,000 bar)

Max working temperature: Ambient to 200°C (400 °F)

Wetted material: Stainless steel, viton

Pressure accuracy: 0.1 % FS

Temperature accuracy: ± 0.5 °C


BENEFITS

Very fast recombination operation due to the magnetic driven stirrer

Versatile, can be used as recombination and restoration unit

Motorized rocking system to set the cell in upright and inverted position


VINCI TECHNOLOGIES


Phone: 331 41 37 92 20 Fax: 331 41 37 04 76



FL

UID

AN

AL

YS

IS

SAMPLE RESTORATION APPARATUS

Very useful for the restoration of the fluid sample, the apparatus enables to heat and agitate the

sample to the reservoir temperature while pressurizing the same sample at the reservoir pressure

using an external high pressure pump. The unit can be proposed into one, two or six cylinder

versions. The sample cylinder is wrapped with a heating mantle and then mounted on the

motorized rocking system to provide the mean to agitate the fluid under pressure and

temperature for several days, if required. The chassis is equipped with four heavy duty casters

which enable to move the apparatus very easily anywhere in the laboratory room.

FEATURES

Temperature: Ambient to 200°C

Temperature accuracy: ± 5°C

Diameter of sample cylinder: 80 mm to 100 mm (other upon request)

Length of sample cylinder: 500 mm to 750 mm (other upon request)


BENEFITS

Efficient stirring mechanism for fluid restoration

Fast heating temperature ramp

Very accurate temperature regulation

Easy to move the apparatus

Easy to mount the fluid sample cylinder


VINCI TECHNOLOGIES


Phone: 331 41 37 92 20 Fax: 331 41 37 04 76



FL

UID

AN

AL

YS

IS

GAS SAMPLE RESTORATION APPARATUS

Very useful during the restoration of gas sample, the apparatus enables to heat and agitate the

sample to the reservoir temperature. One gas sample cylinder can be processed by the rocker.

The sample cylinder is wrapped with a heating mantle and then mounted on the motorized

rocking system to provide the mean to rock the fluid under pressure and temperature for several

days, if required. The chassis is equipped with four heavy duty casters which enable to move the

apparatus very easily anywhere in the laboratory room.

FEATURES



Diameter of accumulator: 200 mm to 250 mm

Length of the accumulator: up to 800 mm

Power supply: 220 VAC,50 Hz

BENEFITS



Easy to move the apparatus

Easy to mount the gas sample cylinder


VINCI TECHNOLOGIES


Phone: 331 41 37 92 20 Fax: 331 41 37 04 76



FL

UID

AN

AL

YS

IS

CYLINDER HEATING MANTLE

The heating mantle offers a convenient, cost-effective way to heat and maintain temperatures of

sample cylinder. They provide clean heat, eliminate hot or cold spots and are easy to install and

remove. They require low maintenance and labor cost, are energy efficient, clean room

compatible, consist of durable material, provide multiple heating zones, remain chemical and

moisture resistant and are easily adaptable to multiple diameters of cylinders. The mantle is

provided with a temperature regulator and it is a plug and play tool. Three sizes are available

depending on the type of cylinder.

FEATURES


Construction: Kevlar, Silicon, glass fiber

Power: 220 VAC, 50 Hz

Type 1: Mantle for CYLIGHT piston cylinders


Diameter range 60 mm to 80 mm

Length range 430 mm

Type 2: Mantle for HPP piston cylinders


Diameter range 80 mm to 100 mm

Length range 500 mm

Type 3: Mantle for gas cylinders


Diameter of accumulator: 200 mm to 250 mm

Length of the accumulator: up to 800 mm


BENEFITS

Convenient

Efficient

Robust and reliable

Attractive

Low maintenance


VINCI TECHNOLOGIES


Phone: 331 41 37 92 20 Fax: 331 41 37 04 76



FL

UID

AN

AL

YS

IS

HEATING TROLLEY FOR LIQUID CYLINDER

The heating trolley is especially designed to heat and maintain at constant temperature

pressurized fluid contained in floating piston accumulator. The trolley is equipped with two

heavy duty casters which enable to transport the fluid sample very easily anywhere in the

laboratory room. A drum also permits to wind the 10 meters extension cord. The accumulator is

mounted into two heating shelves maintained by two clamps. A control panel is used to enter

and display the temperature and set point value. A thermocouple probe is used to measure the

temperature.

FEATURES



Diameter of accumulator: 80 to 100 mm (other upon request)

Length of the accumulator: 500 mm to 750 mm (other upon request)

Power supply: 220 VAC, 50 Hz, 400 watts

BENEFITS

Easy to mount the fluid sample accumulator

Easy to move the trolley in the laboratory room



Homogeneous temperature in the fluid sample


VINCI TECHNOLOGIES


Phone: 331 41 37 92 20 Fax: 331 41 37 04 76



FL

UID

AN

AL

YS

IS

HEATING TROLLEY FOR GAS CYLINDER

The heating trolley is especially designed to heat and maintain at constant temperature

pressurized fluid contained in gas cylinder. The trolley is equipped with two heavy duty casters

which enable to transport the gas sample very easily anywhere in the laboratory room. A drum

also permits to wind the 10 meters extension cord. The cylinder is mounted into two heating

shelves maintained by two clamps. A control panel is used to enter and display the temperature

and set point value. A thermocouple probe is used to measure the temperature.

FEATURES



Diameter of gas cylinder: 200 to 250 mm

Length of the gas cylinder: up to 800 mm

Power supply: 220 VAC, 50 Hz, 700 watts

BENEFITS

Easy to mount the fluid sample accumulator

Easy to move the trolley in the laboratory room



Homogeneous temperature in the fluid sample


VINCI TECHNOLOGIES


Phone: 331 41 37 92 20 Fax: 331 41 37 04 76



FL

UID

AN

AL

YS

IS

GAS BOOSTER (GB – SERIES)

Designed for compression of low pressure field gas samples into cylinders. The gas booster is

complete to operate. All that is required is an air supply for the air driven pump and a cylinder

of storage gas. The device includes manual valves, air regulator, filter, gas booster and high

pressure tubing and fitting.

GB 1000 MODEL:

Type: Double stage - double effect

Admission pressure: 15 bar to 200 bar (about 225 to 2,900psi).

Max outlet pressure: 700 bar (10,000 psi) or 1000 bar (15,000 psi).

Pressure increase ratio: 1:150

Working temperature: Ambient 25° - 50 °C

Air drive: 0.5 to 10 bar (7 to 145psi)

Process fluids: Dry HC gas

GB 700 MODEL:

Type: Single stage - single effect

Admission pressure: 15 bar to 200 bar (about 225 to 2,900psi).

Max outlet pressure: 700 bar (10,000 psi) or 1000 bar (15,000 psi).

Pressure increase ratio: 1:75

Working temperature: Ambient 25° - 50 °C

Air drive: 0.5 to 10 bar (7 to 145psi)

Process fluids: Dry HC gas


VINCI TECHNOLOGIES


Phone: 331 41 37 92 20 Fax: 331 41 37 04 76



FL

UID

AN

AL

YS

IS

SOLVENT CLEANER

The solvent cleaner is a mobile device designed for cleaning high pressure dirty cells. The

principle consists of filling the 20 litres reservoir of the device with half of the solvent and the

remaining with compressed air. The device comes with two valves. One valve is used for filling

the pre-evacuated cell with solvent and compressed air and the second one for injecting the

pressurized solvent into the dirty cell.

FEATURES

Max pressure 100 psi

Volume 20 liters

Air requirement 10 bar (150 psi), dry


VINCI TECHNOLOGIES


Phone: 331 41 37 92 20 Fax: 331 41 37 04 76



FL

UID

AN

AL

YS

IS

PRESSURE GENERATOR SYSTEM (PGS)

Designed to provide hydraulic pressure for Hg free fluid transfer at pressure condition.

Maximum output is 10,000 psi. The system comes complete with air driven liquid pump,

pressure gauge, air regulator, relief valve and frame.

FEATURES

Max outlet pressure: 700 bar (10,000 psi)

Air inlet: 30 to 145 psi (10 bar)



VINCI TECHNOLOGIES


Phone: 331 41 37 92 20 Fax: 331 41 37 04 76



FL

UID

AN

AL

YS

IS

Calibration

DEADWEIGHT GAUGE

Primary pressure standard designed for high pressure calibration applications. The device

consists of a vertically mounted precision lapped piston and cylinder assembly. Accurately

calibrated masses are loaded onto the piston, which rises freely within its cylinder. These

weights balance the upward force created by the application of pressure within the system.

Delivered with a carrying case.

FEATURES

Model: Dual piston

Operation: Oil operated

Pressure range: 1 bar (15 psi) to 1,100 bar (16,000 psi)

Accuracy: 0.015% RDG


VINCI TECHNOLOGIES


Phone: 331 41 37 92 20 Fax: 331 41 37 04 76



FL

UID

AN

AL

YS

IS

DIGITAL PRESSURE GAUGE (DPG SERIES)

The Digital Pressure Gauge series is designed for extremely accurate pressure measurement to

meet your most demanding requirements for precision laboratory or field measurement

instrumentation. The instrument includes a high precision analog pressure transducer, a rupture

disc for over pressure protection, a five digit digital display and a data logging software for

automatic data acquisition.

FEATURES

Model DPG series

Pressure range up to 10,000 psi (other range available)

Accuracy 0.1% FS

Port connection 1/8” autoclave type

Wetted part stainless steel

Power supply 220 VAC 1 Ph, 50 Hz


VINCI TECHNOLOGIES


Phone: 331 41 37 92 20 Fax: 331 41 37 04 76



FL

UID

AN

AL

YS

IS

Power suppl y back up

UNINTERRUPTIBLE POWER SUPPLY (UPS 16)

Back-up power protection used in most laboratories against electrical noise, sags, surges and

brownouts which affect the sensitivity of the electrical components of the laboratory equipment.

FEATURES

Output power capacity: 12,800 Watts / 16,000 VA

Max configurable power: 12,800 Watts / 16,000 VA

Input voltage: 240 V +-1 %, single phase

Output voltage: 240 V +-1 %, single phase

Efficiency at full load: 90%

Back up time: 6 minutes at full load (12,800 watts)

17 minutes at half load (6,400 Watts)


Documents

C ATALOGUE OF PRODUCTS 2015 VINCI · PDF fileVINCI TECHNOLOGIES ATALOGUE OF PRODUCTS FLUID YSIS C 2015 FLUID ANALYSIS PVT H/C Composition Flow assurance Fluid sampling