Upload
ptyxaubl
View
104
Download
1
Embed Size (px)
DESCRIPTION
bsplcmi
Citation preview
Nokia Siemens Networks GSM/EDGE BSS, rel. RG10(BSS), operating documentation, issue 04
Reference
BTSplus mainline commands at the Flexi BSC product family
DN0933412 Issue 01
2DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805d062b
The information in this document is subject to change without notice and describes only the product defined in the introduction of this documentation. This documentation is intended for the use of Nokia Siemens Networks customers only for the purposes of the agreement under which the document is submitted, and no part of it may be used, reproduced, modified or transmitted in any form or means without the prior written permission of Nokia Siemens Networks. The documentation has been prepared to be used by professional and properly trained personnel, and the customer assumes full responsibility when using it. Nokia Siemens Networks welcomes customer comments as part of the process of continuous development and improvement of the documentation.
The information or statements given in this documentation concerning the suitability, capacity, or performance of the mentioned hardware or software products are given "as is" and all liability arising in connection with such hardware or software products shall be defined conclusively and finally in a separate agreement between Nokia Siemens Networks and the customer. However, Nokia Siemens Networks has made all reasonable efforts to ensure that the instructions contained in the document are adequate and free of material errors and omissions. Nokia Siemens Networks will, if deemed necessary by Nokia Siemens Networks, explain issues which may not be covered by the document.
Nokia Siemens Networks will correct errors in this documentation as soon as possible. IN NO EVENT WILL Nokia Siemens Networks BE LIABLE FOR ERRORS IN THIS DOCUMENTA-TION OR FOR ANY DAMAGES, INCLUDING BUT NOT LIMITED TO SPECIAL, DIRECT, INDI-RECT, INCIDENTAL OR CONSEQUENTIAL OR ANY LOSSES, SUCH AS BUT NOT LIMITED TO LOSS OF PROFIT, REVENUE, BUSINESS INTERRUPTION, BUSINESS OPPORTUNITY OR DATA,THAT MAY ARISE FROM THE USE OF THIS DOCUMENT OR THE INFORMATION IN IT.
This documentation and the product it describes are considered protected by copyrights and other intellectual property rights according to the applicable laws.
The wave logo is a trademark of Nokia Siemens Networks Oy. Nokia is a registered trademark of Nokia Corporation. Siemens is a registered trademark of Siemens AG.
Other product names mentioned in this document may be trademarks of their respective owners, and they are mentioned for identification purposes only.
Copyright © Nokia Siemens Networks 2009. All rights reserved
f Important Notice on Product Safety Elevated voltages are inevitably present at specific points in this electrical equipment. Some of the parts may also have elevated operating temperatures.
Non-observance of these conditions and the safety instructions can result in personal injury or in property damage.
Therefore, only trained and qualified personnel may install and maintain the system.
The system complies with the standard EN 60950 / IEC 60950. All equipment connected has to comply with the applicable safety standards.
The same text in German:
Wichtiger Hinweis zur Produktsicherheit
In elektrischen Anlagen stehen zwangsläufig bestimmte Teile der Geräte unter Span-nung. Einige Teile können auch eine hohe Betriebstemperatur aufweisen.
Eine Nichtbeachtung dieser Situation und der Warnungshinweise kann zu Körperverlet-zungen und Sachschäden führen.
Deshalb wird vorausgesetzt, dass nur geschultes und qualifiziertes Personal die Anlagen installiert und wartet.
Das System entspricht den Anforderungen der EN 60950 / IEC 60950. Angeschlossene Geräte müssen die zutreffenden Sicherheitsbestimmungen erfüllen.
DN0933412 Issue 013
BTSplus mainline commands at the Flexi BSC product family
Id:0900d805805d062b
Table of ContentsThis document has 749 pages.
Summary of changes. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 201.1 General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 201.1.1 Structure of the manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 211.1.2 Structure of the commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 221.1.3 Ranges for the relative number of the BTSE objects. . . . . . . . . . . . . . . 221.1.4 Command layout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 251.2 Graphical user interface (GUI) representation of the LMT Evolution. . . 271.2.1 Start LMT Evolution window . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 271.2.2 LMT Evolution windows for GET, CREATE, SET, ..., commands . . . . . 301.3 Command tree . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 331.3.1 Command tree for HW objects . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 331.3.2 Alphabetical list of commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
2 Objects and commands in alphabetical order . . . . . . . . . . . . . . . . . . . . 48
ACDCP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49CREATE ACDCP. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49DELETE ACDCP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51GET ACDCP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52GETTEST ACDCP. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54LOCK ACDCP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55PERFTEST ACDCP. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57STOPTEST ACDCP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61UNLOCK ACDCP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62
ACT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64CREATE ACT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64DELETE ACT. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66GET ACT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67GETTEST ACT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69LOCK ACT. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70PERFTEST ACT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72STOPTEST ACT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76UNLOCK ACT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77
BATTERY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79CREATE BATTERY. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79DELETE BATTERY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81GET BATTERY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82GETTEST BATTERY. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84LOCK BATTERY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 86PERFTEST BATTERY. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87STOPTEST BATTERY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91UNLOCK BATTERY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 92
4DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805d062b
BCOM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 95CREATE BCOM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 95DELETE BCOM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 98GET BCOM. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 99GETRELATIONSHIP BCOM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 101GETTEST BCOM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 103GETWIRINGRX BCOM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 104GETWIRINGTX BCOM. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 106LOCK BCOM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 108PERFTEST BCOM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 109SET BCOM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 113SETWIRINGRX BCOM. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 115SETWIRINGTX BCOM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 117STOPTEST BCOM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 119UNLOCK BCOM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 120
BPORT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 123CREATE BPORT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 123DELETE BPORT. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 126GET BPORT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 127LOCK BPORT. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 129SET BPORT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 131UNLOCK BPORT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 132
BTS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 135GET BTS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 135GET BTS TIMER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 141
BTSEP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 143DELETE BTSEP DBFILE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 143FORMAT BTSEP FLASH . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 144GET BTSEP NOSWL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 145GET BTSEP SWL. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 148GET ACTIVEALARMS BTSEP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 149PERFTEST BTSEP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 152PING BTSEP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 156REQCURSTASYN BTSEP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 157SET BTSEP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 157STOPTEST BTSEP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 159
BTSETEST . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 161GET BTSETEST. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 161
BTSM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 163ACTIVATE BTSM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 163ACTIVATE_DELAYED BTSM. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 165CONNBSC BTSM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 165DISCBSC BTSM. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 167FWUPGRADE BTSM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 168GET BTSM NOSWL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 169
DN0933412 Issue 015
BTSplus mainline commands at the Flexi BSC product family
Id:0900d805805d062b
GET BTSM OVERLOAD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 171GET BTSM SWL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 172LOCKREQUEST BTSM. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 174SET BTSM. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 175SHUTDOWN BTSM. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 176UNLOCKREQUEST BTSM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 177
CESPW . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 179CREATE CESPW . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 179DELETE CESPW. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 181GET CESPW . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 182LOCK CESPW. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 184SET CESPW . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 185UNLOCK CESPW . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 186
CESTUNNEL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 188CREATE CESTUNNEL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 188DELETE CESTUNNEL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 189GET CESTUNNEL. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 190LOCK CESTUNNEL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 192SET CESTUNNEL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 193UNLOCK CESTUNNEL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 194
CHAN. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 196GET CHAN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 196
COBA. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 198CREATE COBA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 198DELETE COBA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 200GET COBA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 201GETRELATIONSHIP COBA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 203GETTEST COBA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 204LOCK COBA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 206PERFTEST COBA. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 207SET COBA. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 211STOPTEST COBA. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 212SWITCH COBA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 214UNLOCK COBA. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 215
COBAETHINTF . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 217GET COBAETHINTF . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 217LOCK COBAETHINTF. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 218SET COBAETHINTF . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 219UNLOCK COBAETHINTF . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 220
COSA. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 221CREATE COSA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 221DELETE COSA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 222GET COSA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 224GETTEST COSA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 225LOCK COSA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 227
6DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805d062b
PERFTEST COSA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 229STOPTEST COSA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 233UNLOCK COSA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 234
CU. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 236CREATE CU . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 236DELETE CU . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 237GET CU . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 239GET CU FWID . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 241GET CU WIRING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 242GETTEST CU . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 243LOCK CU . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 245PERFTEST CU . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 246SET CU. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 250STOPTEST CU. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 251UNLOCK CU. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 252
DIDCTMA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 255CREATE DIDCTMA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 255DELETE DIDCTMA. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 256GET DIDCTMA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 258GETTEST DIDCTMA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 259LOCK DIDCTMA. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 261PERFTEST DIDCTMA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 263STOPTEST DIDCTMA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 266UNLOCK DIDCTMA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 268
DILNA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 270CREATE DILNA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 270DELETE DILNA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 272GET DILNA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 274GETTEST DILNA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 275LOCK DILNA. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 277PERFTEST DILNA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 279SET DILNA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 282STOPTEST DILNA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 284UNLOCK DILNA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 285
DUAMCO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 287DELETE DUAMCO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 287GET DUAMCO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 288GETTEST DUAMCO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 289LOCK DUAMCO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 290PERFTEST DUAMCO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 291STOPTEST DUAMCO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 291UNLOCK DUAMCO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 292
DUDCTMA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 294CREATE DUDCTMA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 294DELETE DUDCTMA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 295
DN0933412 Issue 017
BTSplus mainline commands at the Flexi BSC product family
Id:0900d805805d062b
GET DUDCTMA. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 297GETTEST DUDCTMA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 298LOCK DUDCTMA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 300PERFTEST DUDCTMA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 302STOPTEST DUDCTMA. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 305UNLOCK DUDCTMA. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 307
DULNA. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 309CREATE DULNA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 309DELETE DULNA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 311GET DULNA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 313GETTEST DULNA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 315LOCK DULNA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 316PERFTEST DULNA. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 318SET DULNA. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 322STOPTEST DULNA. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 323UNLOCK DULNA. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 324
DUVSWR. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 327CREATE DUVSWR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 327DELETE DUVSWR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 329GET DUVSWR. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 330GETTEST DUVSWR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 332LOCK DUVSWR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 334PERFTEST DUVSWR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 335SET DUVSWR. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 339STOPTEST DUVSWR. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 341UNLOCK DUVSWR. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 342
ENVABTSE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 344CREATE ENVABTSE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 344DELETE ENVABTSE. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 348GET ENVABTSE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 349LOCK ENVABTSE. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 351SET ENVABTSE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 353UNLOCK ENVABTSE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 354
ETHCON . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 356CREATE ETHCON . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 356DELETE ETHCON. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 357GET ETHCON . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 358LOCK ETHCON. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 359SET ETHCON . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 360UNLOCK ETHCON . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 361
ETHPORT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 363CREATE ETHPORT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 363DELETE ETHPORT. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 364GET ETHPORT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 365LOCK ETHPORT. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 366
8DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805d062b
SET ETHPORT. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 367UNLOCK ETHPORT. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 368
F6DCTMA. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 370CREATE F6DCTMA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 370DELETE F6DCTMA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 371GET F6DCTMA. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 372GETTEST F6DCTMA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 373LOCK F6DCTMA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 374PERFTEST F6DCTMA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 375STOPTEST F6DCTMA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 376UNLOCK F6DCTMA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 378
F6LNA. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 379CREATE F6LNA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 379DELETE F6LNA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 380GET F6LNA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 381GETTEST F6LNA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 383LOCK F6LNA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 384PERFTEST F6LNA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 385SET F6LNA. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 386STOPTEST F6LNA. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 387UNLOCK F6LNA. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 388
F6TNFP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 390CREATE F6TNFP. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 390DELETE F6TNFP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 391GET F6TNFP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 392GETTEST F6TNFP. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 393LOCK F6TNFP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 394PERFTEST F6TNFP. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 395STOPTEST F6TNFP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 396UNLOCK F6TNFP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 397
F6VSWRP. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 398CREATE F6VSWRP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 398DELETE F6VSWRP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 399GET F6VSWRP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 400GETTEST F6VSWRP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 401LOCK F6VSWRP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 402PERFTEST F6VSWRP. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 403SET F6VSWRP. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 404STOPTEST F6VSWRP. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 405UNLOCK F6VSWRP. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 406
FANP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 408CREATE FANP. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 408DELETE FANP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 410GET FANP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 411GETTEST FANP. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 413
DN0933412 Issue 019
BTSplus mainline commands at the Flexi BSC product family
Id:0900d805805d062b
LOCK FANP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 414PERFTEST FANP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 416STOPTEST FANP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 420UNLOCK FANP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 421
FCUMAIN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 423CREATE FCUMAIN. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 423DELETE FCUMAIN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 425GET FCUMAIN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 427GET FCUMAIN FWID . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 428GET FCUMAIN WIRING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 429GETTEST FCUMAIN. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 430LOCK FCUMAIN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 432PERFTEST FCUMAIN. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 433SET FCUMAIN. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 437STOPTEST FCUMAIN. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 438UNLOCK FCUMAIN. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 439
FCUTR. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 442CREATE FCUTR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 442DELETE FCUTR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 444GET FCUTR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 445GETTEST FCUTR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 447LOCK FCUTR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 448PERFTEST FCUTR. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 450SET FCUTR. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 454STOPTEST FCUTR. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 455UNLOCK FCUTR. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 456
FTNFP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 458CREATE FTNFP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 458DELETE FTNFP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 460GET FTNFP. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 461GETTEST FTNFP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 463LOCK FTNFP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 464PERFTEST FTNFP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 466STOPTEST FTNFP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 470UNLOCK FTNFP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 471
FVSWRP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 473CREATE FVSWRP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 473DELETE FVSWRP. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 475GET FVSWRP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 476GETTEST FVSWRP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 477LOCK FVSWRP. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 479PERFTEST FVSWRP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 481STOPTEST FVSWRP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 484UNLOCK FVSWRP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 486
LAPDLE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 488
10DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805d062b
CREATE LAPDLE. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 488DELETE LAPDLE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 490GET LAPDLE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 491
RACK . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 493CREATE RACK . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 493DELETE RACK . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 495GET RACK . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 496LOCK RACK . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 498SET RACK . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 499UNLOCK RACK . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 500
REMINV . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 503DNLIDFD REMINV . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 503UPLLIDF REMINV . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 504
SOFTWARE-MANAGEMENT. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 506DNLALLEXE SOFTWARE-MANAGEMENT. . . . . . . . . . . . . . . . . . . . . 506UPLBTSLOG SOFTWARE-MANAGEMENT . . . . . . . . . . . . . . . . . . . . 507
SYNCBTSE. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 510GET SYNCBTSE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 510GETTEST SYNCBTSE. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 511LOCK SYNCBTSE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 513PERFTEST SYNCBTSE. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 515SET SYNCBTSE. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 518STOPTEST SYNCBTSE. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 520UNLOCK SYNCBTSE. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 521
TMA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 523CREATE TMA. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 523DELETE TMA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 525GET TMA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 526GET TMA PRODUCTINFO. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 527GETTEST TMA. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 529LOCK TMA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 530PERFTEST TMA. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 532STOPTEST TMA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 536UNLOCK TMA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 537
TRX. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 539GET TRX . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 539GETRELATIONSHIP TRX . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 541
XCONNECT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 543CREATE XCONNECT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 543DELETE XCONNECT. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 545GET XCONNECT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 546LOCK XCONNECT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 550SET XCONNECT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 552UNLOCK XCONNECT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 553
DN0933412 Issue 0111
BTSplus mainline commands at the Flexi BSC product family
Id:0900d805805d062b
3 Parameters/attributes in alphabetical order . . . . . . . . . . . . . . . . . . . . . 555
a. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 556ABISCH . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 556ABISLKSAT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 556ABISTIME . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 557ACBQPFF . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 557ACBQPMAX . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 558ACEFLFF. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 558ACFERMAX. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 559ACLNKTYP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 559ACMAXEFLDMA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 560ACMINEFLDMA. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 560ACONN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 561ACPER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 561ACTVINC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 562ALGNSTEP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 562ALIGCOBA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 562ALRMCLET . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 563ALRMCOUNTER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 563ALRMPERT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 564ALRMSEVXXX . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 564ALRMT1/2/3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 565ALS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 566AMRLKAT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 566AMRLKATWFS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 567ANT<x>CELLNO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 568ANT<x>SCNRX . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 569ANT<x>WDRX. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 569ANT<x>WDTX . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 572ANTB . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 574ANTHOPHW . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 574ANTHOPMOD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 575ANTHOPP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 575ANTHOPST . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 575ANTMN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 576ANTSN. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 576ARFACCHACMDF. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 576ASCICIPH . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 577ASEV . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 578AST . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 578ASTRING. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 579ASUBLKSAT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 579AVS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 579
b. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 581BATTCAP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 581BCCHFREQ. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 581
12DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805d062b
BCOMTYPE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 582BCPBL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 583BERT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 583BMWD<x>. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 584BND<x> . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 584BSIC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 585BSWVER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 585BTSID . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 586BTSISHOP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 586BTSOBJID . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 587BURNOFFS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 587
c . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 588CCPBL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 588CELLNO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 588CELLTYPE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 589CHIDT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 589CHTYPE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 590CLKACC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 592COMBMD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 592CUCONF. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 593CUWIRING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 593
d . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 595DESTDIR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 595DLTESTFREQ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 595DMACFHSYID . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 595DMCFWID. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 596DTMHOMTIMER. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 596DYNPOOLINFO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 596DYNTRACGRAN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 599
e . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 600EAC. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 600EANTHOP. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 600EAUTONEG . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 600EAUTOREC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 601EEOTD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 601EEXCDIST . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 602EFCUSUP. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 602EFLWCTRL. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 603EINTSITSYN. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 604EMT1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 604EMT2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 604ENTRIES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 605EQUPOS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 605ERFACCHALPDMF . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 606ERFACCHCMDF . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 608ERSACCHDL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 610
DN0933412 Issue 0113
BTSplus mainline commands at the Flexi BSC product family
Id:0900d805805d062b
ERSACCHUL. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 615ETOP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 620ETXDIVTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 622EVTYP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 623EXCDIST . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 623EXTMODE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 624
f . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 625F6FWID . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 625FACCHQ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 625FACHBT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 625FBAND. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 626FCUMAINWIRING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 626FCUMODE. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 627FILE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 628FILEFWV . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 628FILEID . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 628FILESWV . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 630FILETYPE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 631FPGAFWVER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 631FRANOFFS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 632FWVER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 632
g. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 633GN<x> . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 633GNA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 633GNADB . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 634GNR. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 635GSMTIME . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 635GTWADRV4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 636
h. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 637HOPMODE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 637HSN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 637
i . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 638INSD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 638INSID . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 638INTAVEPAR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 638INTCLASS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 639INTINF . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 639INTLVBND . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 639IPADR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 640
l . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 641L1CTRLTS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 641L1PT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 641L1RAT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 642LAPDCH . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 642LAPDOVLT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 643
14DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805d062b
LAPDOVLTH. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 644LCONF . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 645LIMP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 645LMTLSESS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 646LMTLTIME . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 647LMTUAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 647LMTUNAME . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 648LNAMDB . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 648LNAMODE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 649LNAPRED. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 649LOCALADDR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 652LOCLUDP. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 652LOCNAME . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 652LOSPKTTH . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 653LPDLMSAT. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 653LRU. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 653LSIND . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 654
m. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 656MACADDR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 656MAIO. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 656MAXGN. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 656MAXPDV. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 657MINGN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 657MOBALLOC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 657MOEC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 659MONPRT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 659MORT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 660MPHERR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 661MPTSLXX . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 661MRSYNCT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 662MSDISTBEHAV . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 663MSTXPMAX . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 663MSTXPMAXC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 664MTLT. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 665MTYP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 665
n . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 667NEPTTREP. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 667NTWTYPC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 667NTWTYPE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 667NY1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 669NY2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 669
o . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 670OMLAPDRT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 670OST. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 670OUTPUT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 671OUTPUTPR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 671
DN0933412 Issue 0115
BTSplus mainline commands at the Flexi BSC product family
Id:0900d805805d062b
OVERWRITE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 671OVPTINS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 672
p. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 673PCCCHLDI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 673PEERADDR. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 673PEERUDPPORT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 673PKTLAT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 674PNGF. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 674PNGPKT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 675PNOFACCH. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 675PRDINF . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 675PRDIRECT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 676PRS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 676PSTAT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 677PUSG. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 677PWNAME. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 678PWROUT. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 678PWRRED. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 679
r . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 680RACHBT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 680RACHLAS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 680RADIOMG . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 680RADIOMR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 681RADIUSEXT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 681RELEQUIPOBJ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 682RELFUNCOBJ. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 682REPTYP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 684RFRSINDP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 685RSACCHRXLDL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 685RSACCHRXLUL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 685RSACCHTODL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 686RSACCHTOUL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 686RXBMAXF . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 686RXBMINF. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 687RXDIVSV . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 687RXLEVADJ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 687RXLEVADJN1D1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 688RXSIGLEVADJ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 688RXSIGLEVADJC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 689RXSWCURSET . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 689
s . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 690SALUNAME . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 690SBPRT. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 690SCELLNO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 690SCID . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 691SCLPRIOLST . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 692
16DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805d062b
SEGMENTID. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 693SFPSERID . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 694SHLAPDIT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 694SLOTNO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 695SRADIUSEXT. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 695SRCDIR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 696SRCPATH. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 696STATIME . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 696STDBYST . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 697SUBUNT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 697SWBCAPABILITY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 697SWBSERVSTATE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 698SWLCFID . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 698SWLCVER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 699SWLDINT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 700SWLDSAF. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 701SWLDST. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 701SYNCHRO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 702SYNCSRC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 702SYNCSTAT. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 703SYSID . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 703
t . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 705T200 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 705T3105 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 705T3115 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 706T3151 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 706TAADJ. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 706TCC. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 707TCCCHLDI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 707TDMAP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 708TEI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 709TESTMODE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 709TESTMON . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 710TESTNO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 715TESTOUT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 715TESTPWRRED. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 716TESTST . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 716TEXT. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 716TIMEDELAY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 717TNCH . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 717TNFTARGF. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 717TRXAREA. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 718TRXCPBL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 719TRXFREQ. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 719TRXMD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 720TSC. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 720TSLPOOL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 721
DN0933412 Issue 0117
BTSplus mainline commands at the Flexi BSC product family
Id:0900d805805d062b
TSYNC. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 722TSYNCD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 722TSYNCR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 723TSYNCU . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 723TTRAU. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 724TUPLREP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 724TXBMAXF . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 725TXBMINF . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 725TXDIVTSEXCPT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 725TXDIVTSPAR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 726TXLEVADJ. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 726TXSIGLEVADJ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 727TXSIGLEVADJC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 727TYPOFETH . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 727TYPRACK . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 728
v . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 730VENDNA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 730VGSCULFT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 730VLANID . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 731VSWRTDB. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 731
w . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 733WDDUVSWR. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 733WDFTNFP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 735WDLNA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 737
4 Nack causes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 741
5 Appendix: values for ERFACCHALPDMF, ERFACCHCMDF, ERSACCH-DL, ERSACCHUL and ETOP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 745
6 Appendix B: commands available only in remote mode . . . . . . . . . . . 7486.1 REQCURSTASYN BTSEP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7486.2 GET ENVABTSESUM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 748
18DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805d062b
List of FiguresFigure 1 BTSplus mainline (BS240) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21Figure 2 BTSplus mainline: tree view . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28Figure 3 BTSplus mainline (BS240): graphic view . . . . . . . . . . . . . . . . . . . . . . . . 29Figure 4 BTSplus mainline tree view with list of command . . . . . . . . . . . . . . . . . . 30Figure 5 BTSplus mainline: CREATE ... ACDCP command (example) . . . . . . . . 31Figure 6 BTSplus mainline: SET ... COBA command (example) . . . . . . . . . . . . . 31Figure 7 Command viewer window: CREATE ... BPORT command (example) . . 32Figure 8 Command viewer window: SET ... COBA command (example) . . . . . . . 32Figure 9 Example of BS4x, BS240, BS241, BS240XL, BS240XS/288, BS82 eMicro
main tree . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
DN0933412 Issue 0119
BTSplus mainline commands at the Flexi BSC product family
Summary of changes
Id:0900d805805d0612
Summary of changes
Issue 01 for release RG10(BSS)
Issue Date Summary
01 07/2009 First edition for release RG10(BSS)
20DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805b11a6
Introduction
1 Introduction
1.1 GeneralThis document describes the objects, attributes and related commands necessary to manage the BTSplus mainline NEs.
The way to submit any command is represented by the LMT Evolution tool.
The LMT Evolution, that is the interface between the user and the NE, can manage dif-ferent BTSplus types. For instance, the LMT Evolution is able to recognize and then to visualize the command trees related to the following NEs: • BTSplus mainline (BS-240/BS-241, BS-240 II/241 II/241 II B, BS-240XL, BS-240XL
II, BS-40/41, BS-40 II, BS-82II) • BTSplus basic (BS-240XS, BS-288) • BTSplus eMicro (BS-82)
The LMT Evolution tool is the application commonly used to configure and maintain the GSM network through a set of functions and procedures tailored to operate in a local context. Refer to “Operating guidelines: LMT Evolution”.
Local context means that the LMT Evolution is physically connected to the Network Element through (refer to Figure 1) an interface based on proprietary protocols (HALCA and DLHC).
Anyway, out of the local context, LMT Evolution does not have an overall control on the GSM network and, consequently, available functions are limited to those allowed by local constraints.
The purpose of LMT Evolution is to make Operation and Maintenance easy and to provide all information about the state of an NE.
g Position of COBAs and COSAs. COBA/COSA 0 will be found always on the left side of the rack and COBA/COSA 1 on the right side of the rack.
DN0933412 Issue 0121
BTSplus mainline commands at the Flexi BSC product family
Introduction
Id:0900d805805b11a6
Figure 1 BTSplus mainline (BS240)
1.1.1 Structure of the manualThe manual is divided into five main sections:
1. Section 1 provides general information about command structure and LMT Evolu-tion operations
2. Section 2 describes objects and commands, listed in alphabetical order3. Section 3 describes the parameters of the commands, listed in alphabetical order.
Additionally there is the information in which commands the parameter is used4. Section 4 lists the NACK causes5. Section 5 lists the values for some parameters6. Section 6 lists the values for some commands available only in remote mode
There is the possibility to jump by clicking on the selected item (reference to the param-eter description or to the GUI representation in section 2; reference to the commands in section 3 to the requested information.
In the command representation (section 2) the parameters/attributes in brackets are optional parameters.
22DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805b11a6
Introduction
1.1.2 Structure of the commandsBoth generic commands which can be obtained through selections from the LMT Evo-lution tree and commands which are created by the operator using the CLI interface must use the following syntax:1. Action object [object]:NAME=object:n[/object:n],attribute=value[-value] [,attri-
bute=value];2. Action object :NAME=object:n[/object:n],attribute=value[&value] [,attribute=value];3. Action object [object]:NAME=object:n[/object:n],[REQATTL]=attribute [&attribute];4. Action object [object]:NAME=object:n[/object:n];
g The syntax rules shown in example 2. are used only for GET commands.
where:
"Action" specifies the command that is being executed and that belongs to a list of func-tions applicable to the BTSE system (for example: "CREATE", "DELETE", "SET", etc).
“object” represents the hardware or logical identifier that must be submitted to the command (for example: "RACK", "CU", "BTSM", etc).
“[object]” logical identifier that must be submitted to the commands DELETE BTSEP (for example: "DBFILE") FORMAT BTSEP (for example: "FLASH"), GET BTSEP (for example: "NOSWL", "SWL") or GET CU (for example: "ESN", "NOESN").
"name" specifies the relative number (for example: ACDCP:n n=0, CU:n n=0..11, etc. See table below). The LMT Evolution CLI allows “*” or “&” instead of a simple number for a object instance (for example: CU:* (all), CU:0&2&3 (0,2,3) or CU:0&&3 (0,1,2,3).
"attribute" is the acronym of the real attribute of an object (for example: LNAPRED= Low Noise Amplifier Predecessor of DULNA, etc.).
"value" represent the value of the attribute (or the values of its fields). It is possible to input a value not just using the default data type (usually decimal) but also to input the data e.g. as hex value or as binary value.
1.1.3 Ranges for the relative number of the BTSE objectsThe ranges shown on the LMT Evolution for the relative numbers of the managed objects depends on the type of hardware to which the LMT Evolution itself is connected. The following tables show the ranges allowed for the managed objects of the different type of BTSE racks (i.e. base, extension, service) relevant to BTSplus Mainline.
BS240 /BS241 BS240SR BS241SR
BS240XL BS240XLSR BS4x
ACDCP - 0..1 - 0..1 0
ACT 0 0 0 0 0
BATTERY - 0..3 - 0..3 0..1
BCOM 0..1 - 0..1 - -
BPORT 0..7 - 0..7 - 0..7
BTS 0..11 - 0..11 - 0..3
BTSEP 0 - 0 - 0
BTSM 0 - 0 - 0
DN0933412 Issue 0123
BTSplus mainline commands at the Flexi BSC product family
Introduction
Id:0900d805805b11a6
g *) ENVABTSE object instances 0..56 exist only for rack 0, for other rack instances the range is 0..8.
g **) ENVABTSE object instances 0 and 1 are not supported by BS240XL, BS240XLSR.
g ***) COSA, FANP, TMA: no processor
g The LMU function is no longer supported. Do not use any LMU commands.
CHAN 0..7 - 0..7 - 0..7
COBA 0..1 - 0..1 - 0..1
COSA***) 0..1 - 0..1 - 0..1
CU 0..7 - 0..11 - 0..3
DIDCTMA 0..3 - 0..7 - 0..1
DILNA 0..3 - 0..7 - 0..1
DUAMCO 0..3 - 0..5 - 0..1
DUDCTMA 0..7 - 0..11 - 0..3
DULNA 0..7 - 0..11 - 0..3
DUVSWR 0..7 - 0..11 - 0..3
ENVABTSE 0..56 *) 0..8 0..56 *) **) 0..8 **) 0..56
ETHCON 0 0 0 0 0
F6DCTMA 0..3 - 0..3 - -
F6LNA 0..3 - 0..3 - -
F6TNFP 0..11 - 0..11 - -
F6VSWRP 0..1 - 0..1 - -
FANP***) 0..5 0..5 0..7 0..7 0..5
FCUMAIN 0..7 - 0..11 - 0..3
FCUTR 0..15 - 0..23 - 0..7
FTNFP 0..7 - 0..7 - 0..3
FVSWRP 0..3 - 0..3 - 0..1
LAPDLE 0..10 0..10 0..10 0..10 0..10
LMU 0 - 0 - -
RACK 0..7 4..7 0, 1, 3..7 3..7 0, 4..7
BTSETEST 1..255 1..255 1..255 1..255 1..255
TMA***) 0..11 - 0..15 - 0..5
SYNCBTSE 0 0 0 0 0
TRX 0..23 - 0..23 - 0..3
XCONNECT 0..7 - 0..7 - 0..7
BS40II BS82II
ACDCP - 0
24DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805b11a6
Introduction
ACT 0 0
BATTERY - 0
BCOM - -
BPORT 0..7 0..3 (note)
BTS 0..3 0..5
BTSEP 0 0
BTSM 0 0
CHAN 0..7 0..7
COBA 0..1 0
COSA 0..1 -
CU 0..3 0..1
DIDCTMA - 0..1
DILNA - 0..1
DUDCTMA 0..7 0..1
DULNA 0..7 0..1
DUVSWR 0..7 0..1
ENVABTSE 0..56 *) 0..5
ETHCON 0 0
F6DCTMA - -
F6LNA - -
F6TNFP - -
F6VSWRP - -
FANP 0..4 0
FCUMAIN 0..3 0..1
FCUTR 0..7 0..3
FCUMAIN 0..3 0..1
FCUTR 0..7 0..3
FTNFP 0..7 -
FVSWRP 0..3 -
LAPDLE 0..10 0..10 (note)
LMU - -
RACK 0, 4..7 0..2
BTSETEST 1..255 1..255
TMA 0..7 0..3
SYNCBTSE 0 0
TRX 0..3 0..5
DN0933412 Issue 0125
BTSplus mainline commands at the Flexi BSC product family
Introduction
Id:0900d805805b11a6
g *) ENVABTSE object instances 0..56 exist only for rack 0, for other rack instances the range is 0..8.
g BS82II BPORT object: range 0..3 is supported only if COBA4P12 is installed, in all other cases the range is 0..1.
g BS82II LAPDLE object: in case of COBA4P12 the BTSE will reject the creation of object instances 5..10.
g BS82II XCONNECT object: instances #2 and #3 are supported only if COBA4P12 is installed, in all other cases only instances 0 and 1 are allowed.
g The LMU function is no longer supported. Do not use any LMU commands.
1.1.4 Command layoutThe first information given for each command is the phase, or phases, within which the command can be entered. Then, subsequent selections are shown which are required to get the command starting from the LMT Evolution Tree.
The command is specified with its syntax and it is followed by the individual fields used to explain the functions of the command itself.
Command Tree:The command tree shows the way to get the command and a hint to a GUI example in section 1.
Applicability:This field shows the working phases and the user profile which allow the execution of the command. The user profile visibility level is associated with a user identification "user_id" and password. Four user profiles visibility level are provided:
Each profile gives the user different access levels to the system features and the higher is the level the higher is the number of operations which can be performed.
g For “User_id” and Password contact your local service organization.
Command Description:This field explains the function of the command transmitted by the LMT Evolution to the BTSE (when and why it is used, for which operation task).
Long Names:This part shows (for an overview) the abbreviations of the parameters/attributes used in the command and its corresponding long names.
System Responses:
XCONNECT 0..7 0..3 (note)
0 ReadOnly
1 Command Access
2 ReadWrite
3 Super User
26DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805b11a6
Introduction
They are response messages sent as acknowledgment for completion of input commands or they contain information requested by the user. The typical structure of the response messages contains: the date and time, the command line, the system response. The response messages can be either normal (successful) or error mes-sages. In such a case they contain the reason for the failure.
Short system messages such as: indication of system loading/downloading functions in progress, are also reported as information to the LMT Evolution.
Application Guidelines:These are warnings given when using this command or information related to the envi-ronment in which the command is submitted.
Example of Command Execution:This is an example on how to enter the command with its parameters and their relevant values.
DN0933412 Issue 0127
BTSplus mainline commands at the Flexi BSC product family
Introduction
Id:0900d805805b11a6
1.2 Graphical user interface (GUI) representation of the LMT Evolutiong Reference figures: the reported figures are only for reference and could be not
aligned to the last version of LMT Evolution product.
1.2.1 Start LMT Evolution windowThe LMT Evolution tool is the graphical user interface which performs the command interaction with the Network Element. This enables the user to navigate the object con-tainment Tree View (see Figure 2) or Graphic View (see Figure 3) of the NE and to select a specific command from a list of available ones.
From the graphical point of view, the LMT Evolution Main window provides an access point to all the LMT Evolution functionality and represents an overall monitoring mode as regards the connection status information.
According to its dynamic and "adaptive" properties, the LMT Evolution Main window is displayed taking into account the connection and operating parameters that may affect the visualization of the resulting window functionalities.
The main parameters that influence the visualization of LMT Evolution main window are: • Working Context: indicates a mode in which the user is currently working with the
LMT Evolution • Network Element configuration: family, type, phase, version, etc.
By using the LMT Evolution the user can: • Acquire commands, action or scripts • Send and receive messages containing commands or responses to/from the
network element • Have script/commands translation services • Store issued commands and retrieve responses coming from the NE
28DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805b11a6
Introduction
Figure 2 BTSplus mainline: tree view
DN0933412 Issue 0129
BTSplus mainline commands at the Flexi BSC product family
Introduction
Id:0900d805805b11a6
Figure 3 BTSplus mainline (BS240): graphic view
30DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805b11a6
Introduction
1.2.2 LMT Evolution windows for GET, CREATE, SET, ..., commandsThe LMT Evolution is mainly used to build CREATE, SET, GET, LOCK, UNLOCK, etc. commands to be sent to the Network Element. Starting from the containment Tree View or Graphic View,you can perform the following operations: • Select the functional/equipment/software management object • Select a command from the list of commands displayed by the pop up list box (see
Figure 4)
Figure 4 BTSplus mainline tree view with list of command
The presence of ellipses (see SET ... COBA Command) following the name of the command indicates that the command could require a further configuration of the attri-butes before being submitted. In this case the Command Viewer window is opened and the user can fill in the attribute cells as desired.
If no ellipses are present (see GET COBA Command), the command does not need any further configuration and it is submitted to the network element without opening the Command Viewer window.
In case of the presence of ellipses (see CREATE ... BPORT Command in Figure 5 or SET ... COBA Command in Figure 6) the Command Viewer panel is displayed (see Figure 7 and Figure 8). The user has to perform the following operations: • Select one or more parameters and choose the appropriate values, the command is
executed after clicking on the “Submit” button • If, during the translation phase, an error is found in the command string, the
command is not sent to the N.E. In this case reenter the command following the instructions provided by the diagnostic message shown in the right middle pane.
DN0933412 Issue 0131
BTSplus mainline commands at the Flexi BSC product family
Introduction
Id:0900d805805b11a6
Figure 5 BTSplus mainline: CREATE ... ACDCP command (example)
Figure 6 BTSplus mainline: SET ... COBA command (example)
32DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805b11a6
Introduction
Figure 7 Command viewer window: CREATE ... BPORT command (example)
Figure 8 Command viewer window: SET ... COBA command (example)
For all procedures of module replacement the actions to be performed are similar. As first action, the module must be locked, replaced, tested and finally unlocked. Some modules have to be replaced without locking and for some others, the BTSEP has to be switched from phase 3 to 2.
DN0933412 Issue 0133
BTSplus mainline commands at the Flexi BSC product family
Introduction
Id:0900d805805b11a6
1.3 Command tree
1.3.1 Command tree for HW objects
Figure 9 Example of BS4x, BS240, BS241, BS240XL, BS240XS/288, BS82 eMicro main tree
MANAGED ELEMENTBSS-EQUIPMENT
BTSEPBPORT
LAPDLE
XCONNECT
RACK ACDCPACT
COSA
DUDCTMADULNA
BTSETESTREMINV
BSS-FUNCTIONAL
BTSM
BTSTRX
CHAN
SOFTWARE-MANAGEMENT
BATTERY
COBA
CUDIDCTMADILNA
DUVSWRENVABTSE
FCUTR
F6LNA
FANPFCUMAIN
FTNFPFVSWRPF6DTMA
F6VSWRPF6TNFP
SYNCBTSE
CESPW
COBAETHINTF
ETHPORT
CESTUNNEL
BCOM
TMALMU
DUAMCOETHCON
34DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805b11a6
Introduction
DN0933412 Issue 0135
BTSplus mainline commands at the Flexi BSC product family
Introduction
Id:0900d805805b11a6
1.3.2 Alphabetical list of commands
Managed Element Phase1 Phase2 Phase3
ACDCP
CREATE ACDCP CREATE ACDCP
DELETE ACDCP DELETE ACDCP
GET ACDCP GET ACDCP
GETTEST ACDCP GETTEST ACDCP
LOCK ACDCP LOCK ACDCP
PERFTEST ACDCP PERFTEST ACDCP
STOPTEST ACDCP STOPTEST ACDCP
UNLOCK ACDCP UNLOCK ACDCP
Managed Element Phase1 Phase2 Phase3
ACT
CREATE ACT CREATE ACT
DELETE ACT DELETE ACT
GET ACT GET ACT
GETTEST ACT GETTEST ACT
LOCK ACT LOCK ACT
PERFTEST ACT PERFTEST ACT
STOPTEST ACT STOPTEST ACT
UNLOCK ACT UNLOCK ACT
Managed Element Phase1 Phase2 Phase3
BATTERY
CREATE BATTERY CREATE BATTERY
DELETE BATTERY DELETE BATTERY
GET BATTERY GET BATTERY
GETTEST BATTERY GETTEST BATTERY
LOCK BATTERY LOCK BATTERY
PERFTEST BATTERY PERFTEST BATTERY
STOPTEST BATTERY STOPTEST BATTERY
UNLOCK BATTERY UNLOCK BATTERY
Managed Element Phase1 Phase2 Phase3
36DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805b11a6
Introduction
BCOM
CREATE BCOM CREATE BCOM
DELETE BCOM DELETE BCOM
GET BCOM GET BCOM
GETWIRINGRX BCOM GETWIRINGRX BCOM
GETWIRINGTX BCOM GETWIRINGTX BCOM
GETRELATIONSHIP BCOM
GETRELATIONSHIP BCOM
GETTEST BCOM GETTEST BCOM
LOCK BCOM LOCK BCOM
PERFTEST BCOM PERFTEST BCOM
SET BCOM SET BCOM
SETWIRINGRX BCOM SETWIRINGRX BCOM
SETWIRINGTX BCOM SETWIRINGTX BCOM
STOPTEST BCOM STOPTEST BCOM
UNLOCK BCOM UNLOCK BCOM
Managed Element Phase1 Phase2 Phase3
BPORT
CREATE BPORT CREATE BPORT
DELETE BPORT DELETE BPORT
GET BPORT GET BPORT
LOCK BPORT LOCK BPORT
SET BPORT SET BPORT
UNLOCK BPORT UNLOCK BPORT
Managed Element Phase1 Phase2 Phase3
BTS
GET BTS
GET BTS TIMER
Managed Element Phase1 Phase2 Phase3
BTSEP
DELETE BTSEP DBFILE
FORMAT BTSEP FLASH FORMAT BTSEP FLASH
GET BTSEP NOSWL GET BTSEP NOSWL
DN0933412 Issue 0137
BTSplus mainline commands at the Flexi BSC product family
Introduction
Id:0900d805805b11a6
GET BTSEP SWL GET BTSEP SWL
GETACTIVEALARMS BTSEP
GETACTIVEALARMS BTSEP
PERFTEST BTSEP PERFTEST BTSEP
PING BTSEP PING BTSEP
SET BTSEP SET BTSEP
STOPTEST BTSEP STOPTEST BTSEP
Managed Element Phase1 Phase2 Phase3
BTSETEST
GET BTSETEST GET BTSETEST
Managed Element Phase1 Phase2 Phase3
BTSM
ACTIVATE BTSM ACTIVATE BTSM
ACTIVATE_DELAYED BTSM
CONNBSC BTSM
DISCBSC BTSM
FWUPGRADE BTSM FWUPGRADE BTSM
GET BTSM NOSWL GET BTSM NOSWL
GET BTSM OVERLOAD GET BTSM OVERLOAD
GET BTSM SWL GET BTSM SWL
LOCKREQUEST BTSM
SET BTSM
SHUTDOWN BTSM
UNLOCKREQUEST BTSM
Managed Element Phase1 Phase2 Phase3
CESPW
CREATE CESPW CREATE CESPW
DELETE CESPW DELETE CESPW
GET CESPW GET CESPW
LOCK CESPW LOCK CESPW
SET CESPW SET CESPW
38DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805b11a6
Introduction
UNLOCK CESPW UNLOCK CESPW
Managed Element Phase1 Phase2 Phase3
CESTUNNEL
CREATE CESTUNNEL
DELETE CESTUNNEL
GET CESTUNNEL GET CESTUNNEL
LOCK CESTUNNEL
SET CESTUNNEL SET CESTUNNEL
UNLOCK CESTUNNEL
Managed Element Phase1 Phase2 Phase3
CHAN
GET CHAN
Managed Element Phase1 Phase2 Phase3
COBA
CREATE COBA CREATE COBA
DELETE COBA DELETE COBA
GET COBA GET COBA
GETRELATIONSHIP COBA
GETRELATIONSHIP COBA
GETTEST COBA GETTEST COBA
LOCK COBA LOCK COBA
PERFTEST COBA PERFTEST COBA
SET COBA SET COBA
STOPTEST COBA STOPTEST COBA
SWITCH COBA SWITCH COBA
UNLOCK COBA UNLOCK COBA
Managed Element Phase1 Phase2 Phase3
COBAETHINTF
GET COBAETHINTF GET COBAETHINTF
LOCK COBAETHINTF
SET COBAETHINTF
DN0933412 Issue 0139
BTSplus mainline commands at the Flexi BSC product family
Introduction
Id:0900d805805b11a6
UNLOCK COBAETHINTF
Managed Element Phase1 Phase2 Phase3
COSA
CREATE COSA CREATE COSA
DELETE COSA DELETE COSA
GET COSA GET COSA
GETTEST COSA GETTEST COSA
LOCK COSA LOCK COSA
PERFTEST COSA PERFTEST COSA
STOPTEST COSA STOPTEST COSA
UNLOCK COSA UNLOCK COSA
Managed Element Phase1 Phase2 Phase3
CU
CREATE CU CREATE CU
DELETE CU DELETE CU
GET CU GET CU
GET CU FWID GET CU FWID
GET CU WIRING GET CU WIRING
GETTEST CU GETTEST CU
LOCK CU LOCK CU
PERFTEST CU PERFTEST CU
SET CU SET CU
STOPTEST CU STOPTEST CU
UNLOCK CU UNLOCK CU
Managed Element Phase1 Phase2 Phase3
DIDCTMA
CREATE DIDCTMA CREATE DIDCTMA
DELETE DIDCTMA DELETE DIDCTMA
GET DIDCTMA GET DIDCTMA
GETTEST DIDCTMA GETTEST DIDCTMA
LOCK DIDCTMA LOCK DIDCTMA
PERFTEST DIDCTMA PERFTEST DIDCTMA
40DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805b11a6
Introduction
STOPTEST DIDCTMA STOPTEST DIDCTMA
UNLOCK DIDCTMA UNLOCK DIDCTMA
Managed Element Phase1 Phase2 Phase3
DILNA
CREATE DILNA CREATE DILNA
DELETE DILNA DELETE DILNA
GET DILNA GET DILNA
GETTEST DILNA GETTEST DILNA
LOCK DILNA LOCK DILNA
PERFTEST DILNA PERFTEST DILNA
SET DILNA SET DILNA
STOPTEST DILNA STOPTEST DILNA
UNLOCK DILNA UNLOCK DILNA
Managed Element Phase1 Phase2 Phase3
DUAMCO
DELETE DUAMCO DELETE DUAMCO
GET DUAMCO GET DUAMCO
GETTEST DUAMCO GETTEST DUAMCO
LOCK DUAMCO LOCK DUAMCO
PERFTEST DUAMCO PERFTEST DUAMCO
STOPTEST DUAMCO STOPTEST DUAMCO
UNLOCK DUAMCO UNLOCK DUAMCO
Managed Element Phase1 Phase2 Phase3
DUDCTMA
CREATE DUDCTMA CREATE DUDCTMA
DELETE DUDCTMA DELETE DUDCTMA
GET DUDCTMA GET DUDCTMA
GETTEST DUDCTMA GETTEST DUDCTMA
LOCK DUDCTMA LOCK DUDCTMA
PERFTEST DUDCTMA PERFTEST DUDCTMA
STOPTEST DUDCTMA STOPTEST DUDCTMA
UNLOCK DUDCTMA UNLOCK DUDCTMA
DN0933412 Issue 0141
BTSplus mainline commands at the Flexi BSC product family
Introduction
Id:0900d805805b11a6
Managed Element Phase1 Phase2 Phase3
DULNA
CREATE DULNA CREATE DULNA
DELETE DULNA DELETE DULNA
GET DULNA GET DULNA
GETTEST DULNA GETTEST DULNA
LOCK DULNA LOCK DULNA
PERFTEST DULNA PERFTEST DULNA
SET DULNA SET DULNA
STOPTEST DULNA STOPTEST DULNA
UNLOCK DULNA UNLOCK DULNA
Managed Element Phase1 Phase2 Phase3
DUVSWR
CREATE DUVSWR CREATE DUVSWR
DELETE DUVSWR DELETE DUVSWR
GET DUVSWR GET DUVSWR
GETTEST DUVSWR GETTEST DUVSWR
LOCK DUVSWR LOCK DUVSWR
PERFTEST DUVSWR PERFTEST DUVSWR
SET DUVSWR SET DUVSWR
STOPTEST DUVSWR STOPTEST DUVSWR
UNLOCK DUVSWR UNLOCK DUVSWR
Managed Element Phase1 Phase2 Phase3
ENVABTSE
CREATE ENVABTSE CREATE ENVABTSE
DELETE ENVABTSE DELETE ENVABTSE
GET ENVABTSE GET ENVABTSE
LOCK ENVABTSE LOCK ENVABTSE
SET ENVABTSE SET ENVABTSE
UNLOCK ENVABTSE UNLOCK ENVABTSE
Managed Element Phase1 Phase2 Phase3
ETHCON
42DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805b11a6
Introduction
CREATE ETHCON
DELETE ETHCON
GET ETHCON GET ETHCON
LOCK ETHCON
SET ETHCON SET ETHCON
UNLOCK ETHCON
Managed Element Phase1 Phase2 Phase3
ETHPORT
CREATE ETHPORT CREATE ETHPORT
DELETE ETHPORT DELETE ETHPORT
GET ETHPORT GET ETHPORT
LOCK ETHPORT LOCK ETHPORT
SET ETHPORT SET ETHPORT
UNLOCK ETHPORT UNLOCK ETHPORT
Managed Element Phase1 Phase2 Phase3
F6DCTMA
CREATE F6DCTMA CREATE F6DCTMA
DELETE F6DCTMA DELETE F6DCTMA
GET F6DCTMA GET F6DCTMA
GETTEST F6DCTMA GETTEST F6DCTMA
LOCK F6DCTMA LOCK F6DCTMA
PERFTEST F6DCTMA PERFTEST F6DCTMA
STOPTEST F6DCTMA STOPTEST F6DCTMA
UNLOCK F6DCTMA UNLOCK F6DCTMA
Managed Element Phase1 Phase2 Phase3
F6LNA
CREATE F6LNA CREATE F6LNA
DELETE F6LNA DELETE F6LNA
GET F6LNA GET F6LNA
GETTEST F6LNA GETTEST F6LNA
LOCK F6LNA LOCK F6LNA
PERFTEST F6LNA PERFTEST F6LNA
DN0933412 Issue 0143
BTSplus mainline commands at the Flexi BSC product family
Introduction
Id:0900d805805b11a6
SET F6LNA SET F6LNA
STOPTEST F6LNA STOPTEST F6LNA
UNLOCK F6LNA UNLOCK F6LNA
Managed Element Phase1 Phase2 Phase3
F6TNFP
CREATE F6TNFP CREATE F6TNFP
DELETE F6TNFP DELETE F6TNFP
GET F6TNFP GET F6TNFP
GETTEST F6TNFP GETTEST F6TNFP
LOCK F6TNFP LOCK F6TNFP
PERFTEST F6TNFP PERFTEST F6TNFP
STOPTEST F6TNFP STOPTEST F6TNFP
UNLOCK F6TNFP UNLOCK F6TNFP
Managed Element Phase1 Phase2 Phase3
F6VSWRP
CREATE F6VSWRP CREATE F6VSWRP
DELETE F6VSWRP DELETE F6VSWRP
GET F6VSWRP GET F6VSWRP
GETTEST F6VSWRP GETTEST F6VSWRP
LOCK F6VSWRP LOCK F6VSWRP
PERFTEST F6VSWRP PERFTEST F6VSWRP
SET F6VSWRP SET F6VSWRP
STOPTEST F6VSWRP STOPTEST F6VSWRP
UNLOCK F6VSWRP UNLOCK F6VSWRP
Managed Element Phase1 Phase2 Phase3
FANP
CREATE FANP CREATE FANP
DELETE FANP DELETE FANP
GET FANP GET FANP
GETTEST FANP GETTEST FANP
LOCK FANP LOCK FANP
PERFTEST FANP PERFTEST FANP
44DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805b11a6
Introduction
STOPTEST FANP STOPTEST FANP
UNLOCK FANP UNLOCK FANP
Managed Element Phase1 Phase2 Phase3
FCUMAIN
CREATE FCUMAIN CREATE FCUMAIN
DELETE FCUMAIN DELETE FCUMAIN
GET FCUMAIN GET FCUMAIN
GET FCUMAIN FWID GET FCUMAIN FWID
GET FCUMAIN WIRING GET FCUMAIN WIRING
GETTEST FCUMAIN GETTEST FCUMAIN
LOCK FCUMAIN LOCK FCUMAIN
PERFTEST FCUMAIN PERFTEST FCUMAIN
SET FCUMAIN SET FCUMAIN
STOPTEST FCUMAIN STOPTEST FCUMAIN
UNLOCK FCUMAIN UNLOCK FCUMAIN
Managed Element Phase1 Phase2 Phase3
FCUTR
CREATE FCUTR CREATE FCUTR
DELETE FCUTR DELETE FCUTR
GET FCUTR GET FCUTR
GETTEST FCUTR GETTEST FCUTR
LOCK FCUTR LOCK FCUTR
PERFTEST FCUTR PERFTEST FCUTR
SET FCUTR SET FCUTR
STOPTEST FCUTR STOPTEST FCUTR
UNLOCK FCUTR UNLOCK FCUTR
Managed Element Phase1 Phase2 Phase3
FTNFP
CREATE FTNFP CREATE FTNFP
DELETE FTNFP DELETE FTNFP
GET FTNFP GET FTNFP
GETTEST FTNFP GETTEST FTNFP
DN0933412 Issue 0145
BTSplus mainline commands at the Flexi BSC product family
Introduction
Id:0900d805805b11a6
LOCK FTNFP LOCK FTNFP
PERFTEST FTNFP PERFTEST FTNFP
STOPTEST FTNFP STOPTEST FTNFP
UNLOCK FTNFP UNLOCK FTNFP
Managed Element Phase1 Phase2 Phase3
FVSWRP
CREATE FVSWRP CREATE FVSWRP
DELETE FVSWRP DELETE FVSWRP
GET FVSWRP GET FVSWRP
GETTEST FVSWRP GETTEST FVSWRP
LOCK FVSWRP LOCK FVSWRP
PERFTEST FVSWRP PERFTEST FVSWRP
STOPTEST FVSWRP STOPTEST FVSWRP
UNLOCK FVSWRP UNLOCK FVSWRP
Managed Element Phase1 Phase2 Phase3
LAPDLE
CREATE LAPDLE CREATE LAPDLE
DELETE LAPDLE DELETE LAPDLE
GET LAPDLE GET LAPDLE
Managed Element Phase1 Phase2 Phase3
LMU The LMU function is no longer supported. Please do not use any LMU commands.
Managed Element Phase1 Phase2 Phase3
RACK
CREATE RACK CREATE RACK
DELETE RACK DELETE RACK
GET RACK GET RACK
LOCK RACK LOCK RACK
SET RACK
UNLOCK RACK UNLOCK RACK
Managed Element Phase1 Phase2 Phase3
46DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805b11a6
Introduction
REMINV
DNLIDFD REMINV DNLIDFD REMINV
UPLLIDF REMINV UPLLIDF REMINV UPLLIDF REMINV
Managed Element Phase1 Phase2 Phase3
SOFTWARE-MAN-AGEMENT
DNLALLEXE SOFTWARE-MANAGE-MENT
DNLALLEXE SOFTWARE-MANAGE-MENT
UPLBTSLOG SOFTWARE-MANAGE-MENT
UPLBTSLOG SOFTWARE-MANAGE-MENT
Managed Element Phase1 Phase2 Phase3
SYNCBTSE
GET SYNCBTSE GET SYNCBTSE
GETTEST SYNCBTSE GETTEST SYNCBTSE
LOCK SYNCBTSE LOCK SYNCBTSE
PERFTEST SYNCBTSE PERFTEST SYNCBTSE
SET SYNCBTSE SET SYNCBTSE
STOPTEST SYNCBTSE STOPTEST SYNCBTSE
UNLOCK SYNCBTSE UNLOCK SYNCBTSE
Managed Element Phase1 Phase2 Phase3
TMA
CREATE TMA CREATE TMA
DELETE TMA DELETE TMA
GET TMA GET TMA
GET TMA PRODUCT-INFO
GET TMA PRODUCT-INFO
GETTEST TMA GETTEST TMA
LOCK TMA LOCK TMA
PERFTEST TMA PERFTEST TMA
STOPTEST TMA STOPTEST TMA
UNLOCK TMA UNLOCK TMA
DN0933412 Issue 0147
BTSplus mainline commands at the Flexi BSC product family
Introduction
Id:0900d805805b11a6
Managed Element Phase1 Phase2 Phase3
TRX
GET TRX
GETRELATIONSHIP TRX
Managed Element Phase1 Phase2 Phase3
XCONNECT
CREATE XCONNECT CREATE XCONNECT
DELETE XCONNECT DELETE XCONNECT
GET XCONNECT GET XCONNECT
LOCK XCONNECT LOCK XCONNECT
SET XCONNECT SET XCONNECT
UNLOCK XCONNECT UNLOCK XCONNECT
48DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d8058053dfb3
Objects and commands in alphabetical order
2 Objects and commands in alphabetical order
DN0933412 Issue 0149
BTSplus mainline commands at the Flexi BSC product family
ACDCP
Id:0900d805805b0cac
ACDCP The ACDCPconverter consists of two different power supply and control units: ACPSC (AC power supply, charging and supervising of the battery backup system) and DCPSC (DC power supply).
CREATE ACDCP
Command Tree:“MANAGED-ELEMENT h BSS-EQUIPMENT h BTSEP h RACK h ACDCP h CREATE ACDCP”
Applicability:Phase 2 and Phase 3.
Visibility level: 2.
Command Description:This command adds the AC/DC Converter Panel to the BTSE data base.
Long Names:NAME Address of the managed object
System Responses:Operation Completed
After command execution, a message of Changed Configuration Notification is dis-played. A further message indicates the result of the operation. An example of create command is the following:
JOB: 41
PC Time&Date: 11:55:28 03/23/2005
NE Time&Date: 12:57:03 09/15/2004
USER NAME: NSN
COMMAND: Create ACDCP:NAME=RACK:0/ACDCP:0;
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: Operation successful
END OF OUTPUT FOR JOB 41
JOB: 42
PC Time&Date: 11:55:28 03/23/2005
CREATE ACDCP NAME=RACK:0..7/ACDCP:0..1;
50DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805b0cac
ACDCP
NE Time&Date: 12:57:03 09/15/2004
USER NAME: NSN
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: Operation successful
CHANGED STATE EVENT REPORT:
NAME = RACK:0/ACDCP:0
Availability Status = NULL_value
Notification Identifier = 284
END OF OUTPUT FOR JOB 42
Operation Failed
The specified Object has not been created. In addition to the general NACK causes, a specific NACK cause, which indicates that the command is inconsistent with the physical configuration, is possible. An example is the following:
JOB: 43
PC Time&Date: 11:55:28 03/23/2005
NE Time&Date: 12:57:03 09/15/2004
USER NAME: NSN
COMMAND: Create ACDCP:NAME=RACK:0/ACDCP:1;
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: OPERATION FAILED
MO already created (-159)
END OF OUTPUT FOR JOB 43
Application Guidelines:
• The ACDCP is not necessary for the BS240
• The ACDCP can not be created for the BS240 Compact Site as it is equipped in the Energy Station Rack which is not supervised by the SW
• The ACDCP can not be created for the BS240, BS241, BS240XL, BS40II
Example of Command Execution:Create ACDCP:NAME=RACK:0/ACDCP:0;
DN0933412 Issue 0151
BTSplus mainline commands at the Flexi BSC product family
ACDCP
Id:0900d805805b0cac
DELETE ACDCP
Command Tree:“MANAGED-ELEMENT h BSS-EQUIPMENT h BTSEP h RACK h ACDCP h DELETE ACDCP”
Applicability:Phase 2 and Phase 3.
Visibility level: 2.
Command Description:This command deletes the AC/DC Converter Panel from the BTSE data base.
Long Names:NAME Address of the managed object
System Responses:Operation Completed
After command execution, a message of Changed Configuration Notification is dis-played. A further message indicates the result of the operation. An example of delete command is the following:
JOB: 38
PC Time&Date: 11:55:25 03/23/2005
NE Time&Date: 12:57:00 09/15/2004
USER NAME: NSN
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: Operation successful
ChangedConfigurationNotification:
name = RACK:0/ACDCP:0
ChangeInfo = deleted
END OF OUTPUT FOR JOB 38
JOB: 39
PC Time&Date: 11:55:25 03/23/2005
NE Time&Date: 12:57:00 09/15/2004
DELETE ACDCP NAME=RACK:0..7/ACDCP:0..1;
52DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805b0cac
ACDCP
USER NAME: NSN
COMMAND: Delete ACDCP:NAME=RACK:0/ACDCP:0;
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: Operation successful
END OF OUTPUT FOR JOB 39
Operation Failed
The specified Object has not been deleted. Additionally to the general NACK causes, a specific NACK cause, meaning that the command is inconsistent with physical configu-ration, is possible.
Application Guidelines:
• ACDCP must be locked in phase 3 before deletion
• The ACDCP can not be deleted for the BS-240 Compact Site as it is equipped in the Energy Station Rack which is not supervised by the SW
• The ACDCP can not be deleted for the BS-40II
Example of Command Execution:Delete ACDCP:NAME=RACK:0/ACDCP:0;
GET ACDCP
Command Tree:“MANAGED-ELEMENT h BSS-EQUIPMENT h BTSEP h RACK h ACDCP h GET ACDCP”
Applicability:Phase 2 and Phase 3.
Visibility level: 0.
Command Description:This command displays the attributes of the AC/DC converter Panel of the BTSE.
Long Names:NAME Address of the managed object
REQATTL Required attribute list
ALS alarmStatus
AST administrativeState
AVS availabilityStatus
OST operationalState
PRS proceduralStatus
GET ACDCP NAME=RACK:0..7/ACDCP:0..1 [,REQATTL=ALS, AST, AVS, OST, PRS, RELFUNCOBJ];
DN0933412 Issue 0153
BTSplus mainline commands at the Flexi BSC product family
ACDCP
Id:0900d805805b0cac
RELFUNCOBJ relatedFuncObjects
System Responses:Operation Completed
After command execution, a message of Changed Configuration Notification is dis-played. A further message indicates the result of the operation. An example of create command is the following:
JOB: 23
PC Time&Date: 11:55:04 03/23/2005
NE Time&Date: 12:56:39 09/15/2004
USER NAME: NSN
COMMAND: Get ACDCP:NAME=RACK:0/ACDCP:0;
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: Operation successful
alarmStatus = CLEARED
administrativeState = Unlocked
availabilityStatus = NULL
operationalState = ENABLED
proceduralStatus = NULL
relatedFuncObjects =
END OF OUTPUT FOR JOB 23
Operation Failed
The GET command has not been successfully executed. A general NACK will indicate possible errors or a specific NACK strictly related to the single command is possible.
Application Guidelines:
• The GET ACDCP command cannot be issued for the BS-240 Compact Site as the ACDCP is equipped in the Energy Station Rack which is not supervised by the SW
• The GET ACDCP command cannot be issued for the BS-40II
Example of Command Execution:Get ACDCP:NAME=RACK:0/ACDCP:0,REQATTL=ALS&AST&AVS&OST&PRS&
RELFUNCOBJ;
54DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805b0cac
ACDCP
GETTEST ACDCP
Command Tree:“MANAGED-ELEMENT h BSS-EQUIPMENT h BTSEP h RACK h ACDCP h GETTEST ACDCP”
Applicability:Phase 2 and Phase 3.
Visibility level: 0.
Command Description:This command displays the attributes of the AC/DC converter test.
Long Names:NAME Address of the managed object
REQATTL Required attribute list
System Responses:Operation Completed
After command execution, a message of Changed Configuration Notification is dis-played. A further message indicates the result of the operation. An example of create command is the following:
JOB: 36
PC Time&Date: 11:55:22 03/23/2005
NE Time&Date: 12:56:57 09/15/2004
USER NAME: NSN
COMMAND: Gettest ACDCP:NAME=RACK:0/ACDCP:0;
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: Operation successful
MOT = RACK:0/ACDCP:0
testMonitor =
phaseId = PreliminaryTestsAcdcp
phaseStatus = Running
phaseId = CheckAlarmStatusAcdcp
phaseStatus = Waiting
phaseId = EndTestAcdcp
phaseStatus = Waiting
testOutcome = INCONCLUSIVE
GETTEST ACDCP NAME=RACK:0..7/ACDCP:0..1;
DN0933412 Issue 0155
BTSplus mainline commands at the Flexi BSC product family
ACDCP
Id:0900d805805b0cac
testState = INITIALIZING
END OF OUTPUT FOR JOB 36
Operation Failed
The GET command has not been successfully executed. A general NACK will indicate possible errors or a specific NACK strictly related to the single command is possible.
Application Guidelines:None.
Example of Command Execution:Gettest ACDCP:NAME=RACK:0/ACDCP:0;
LOCK ACDCP
Command Tree:“MANAGED-ELEMENT h BSS-EQUIPMENT h BTSEP h RACK h ACDCP h LOCK ACDCP”
Applicability:Phase 2 and Phase 3.
Visibility level: 1.
Command Description:This command changes the administrative state of AC/DC converter Panel of the BTSE.
Long Names:NAME Address of the managed object
testMonitor it is a list of all test phases related to the selected object; for each phase the related phaseStatus is provided (Passed, Failed, Running or Waiting).
phaseId =
phaseStatus =
phaseId =
phaseStatus =
...
...
testOutcome It represents the test result: it can be Inconclusive (if the phases already executed were successful) or Fail (if at least one of the executed phases failed).
testState = Testing It can assume one of the following values: not_initialized, idle, initializing, sus-pended, testing, terminating and dis-abled.
LOCK ACDCP NAME=RACK:0..7/ACDCP:0..1;
56DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805b0cac
ACDCP
System Responses:Operation Completed
The specified change of administrative state has been perfomed:
JOB: 24
PC Time&Date: 11:55:06 03/23/2005
NE Time&Date: 12:56:41 09/15/2004
USER NAME: NSN
COMMAND: Lock ACDCP:NAME=RACK:0/ACDCP:0;
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: Operation successful
administrativeState = Locked
END OF OUTPUT FOR JOB 24
CHANGED STATE EVENT REPORT:
This provides information about the administrative state, the operational state and the availability status every time a state change occurs:
JOB: 25
PC Time&Date: 11:55:06 03/23/2005
NE Time&Date: 12:56:41 09/15/2004
USER NAME: NSN
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: Operation successful
CHANGED STATE EVENT REPORT:
NAME = RACK:0/ACDCP:0
Administrative State = LOCKED
Notification Identifier = 271
END OF OUTPUT FOR JOB 25
DN0933412 Issue 0157
BTSplus mainline commands at the Flexi BSC product family
ACDCP
Id:0900d805805b0cac
Operation Failed
The specified change of administrative state has not been performed (e.g. the object is redundant and its spare copy is disabled or already locked, a subordinate resource cannot go into disabled state with "dependency" availability status).
Application Guidelines:
• The ACDCP can not be locked for the BS-240 Compact Site as it is equipped in the Energy Station Rack which is not supervised by the SW
• The ACDCP can not be locked for the BS-40II
Example of Command Execution:Lock ACDCP:NAME=RACK:0/ACDCP:0;
PERFTEST ACDCP
Command Tree:“MANAGED-ELEMENT h BSS-EQUIPMENT h BTSEP h RACK h ACDCP h PERFTEST ACDCP”
Applicability:Phase 2 and Phase 3.
Visibility level: 1.
Command Description:This command requests the execution of a test performed by the ACDCP.
Long Names:NAME Address of the managed object
System Responses:Operation Completed
Test configuration has been set and the specified test has been started. The System response will not be addressed to the MOT but to the object BTSEP.
JOB: 27
PC Time&Date: 11:55:09 03/23/2005
NE Time&Date: 12:56:44 09/15/2004
USER NAME: NSN
COMMAND: Perftest ACDCP:NAME=RACK:0/ACDCP:0;
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: Operation successful
PERFTEST ACDCP NAME=RACK:0..7/ACDCP:0..1;
58DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805b0cac
ACDCP
MOT = RACK:0/ACDCP:0
tO = BTSETEST:3
END OF OUTPUT FOR JOB 27
JOB: 28
PC Time&Date: 11:55:09 03/23/2005
NE Time&Date: 12:56:44 09/15/2004
USER NAME: NSN
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: Operation successful
ChangedConfigurationNotification:
name = BTSETEST:3
ChangeInfo = created
END OF OUTPUT FOR JOB 28
JOB: 29
PC Time&Date: 11:55:09 03/23/2005
NE Time&Date: 12:56:44 09/15/2004
USER NAME: NSN
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: Operation successful
CHANGED STATE EVENT REPORT:
NAME = RACK:0/ACDCP:0
Operational State = ENABLED
Availability Status = NULL_value
Notification Identifier = 275
END OF OUTPUT FOR JOB 29
JOB: 30
DN0933412 Issue 0159
BTSplus mainline commands at the Flexi BSC product family
ACDCP
Id:0900d805805b0cac
PC Time&Date: 11:55:09 03/23/2005
NE Time&Date: 12:56:44 09/15/2004
USER NAME: NSN
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: Operation successful
Test Report:
name = BTSETEST:3
testOutcome = PASSED
testTermination = Normal
MOT = RACK:0/ACDCP:0
executedPhases =
PreliminaryTestsAcdcp
CheckAlarmStatusAcdcp
EndTestAcdcp
END OF OUTPUT FOR JOB 30
JOB: 31
PC Time&Date: 11:55:09 03/23/2005
NE Time&Date: 12:56:44 09/15/2004
USER NAME: NSN
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: Operation successful
ChangedConfigurationNotification:
name = BTSETEST:3
ChangeInfo = deleted
END OF OUTPUT FOR JOB 31
The test results will be displayed at the end of the test phases.
Result TEST:
60DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805b0cac
ACDCP
Operation Failed
This NACK-message occurs in the following cases: Message cannot be performed, test not supported, capacity restrictions, physical configuration cannot be performed, object not locked.
Application Guidelines:
• In phase 3 MO must be locked previous to the command execution
Example of Command Execution:Perftest ACDCP:NAME=RACK:0/ACDCP:0;
name = TEST:<n>
testOutcome = This field represents the test result; one of the fol-lowing values can be displayed:
Pass all the test phases are successfully performed.
Inconclusive the test is aborted by the system or the test is terminated by the opera-tor.
Fail if at least one of the executed phases fail.
mOts = It is the identifier of the hardware object under test.
testTermination = It specifies how the test is terminated, it can assume the following values:
Normal all the test phases are performed.
Abort the test is aborted by system.
Cancel the test is terminated by operator.
executedPhases
phaseId = It represents the list of the executed test phases (in case of successful test result, all the test phases will be listed).
additionalWords =
....
failedPhases
phaseId = It represents the list of the failed test phase; addi-tional information is provided for each phase.phaseId =
....
skippedPhases
phaseId = It represents the list of the skipped phases; they are displayed only for test stopped during it execution.phaseId =
....
poprosedRepair Action =
A list of most probable fail probable causes is shown (max four messages)
DN0933412 Issue 0161
BTSplus mainline commands at the Flexi BSC product family
ACDCP
Id:0900d805805b0cac
STOPTEST ACDCP
Command Tree:“MANAGED-ELEMENT h BSS-EQUIPMENT h BTSEP h RACK h ACDCP h STOPTEST ACDCP”
Applicability:Phase 2 and Phase 3.
Visibility level: 1.
Command Description:This command stops a test performed by ACDCP.
Long Names:NAME Address of the managed object
System Responses:Operation Completed
Test has been stopped. The System Responses will not be addressed to the MOT but to the object BTSEP.
Operation Failed
Test has not been stopped. This NACK-message can occur when the specified test is not running or in case of test which cannot be stopped.
STOPTEST ACDCP NAME=RACK:0..7/ACDCP:0..1;
Result TEST:
name = TEST:<n>
testOutcome = inconclusive
mOts = It is the identifier of the hardware object under test.
testTermination = Cancel
executedPhases
phaseId = It represents the list of the executed test phases; the list is not shown for test in the waiting list (queued)....
.
failedPhases
phaseId = It represents the list of the failed test phase;
additional information is provided for each phase.phaseId =
....
skippedPhases
phaseId = It represents the list of the skipped phases;the list is not shown for test in the waiting list (queued).phaseId =
62DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805b0cac
ACDCP
Application Guidelines:None.
Example of Command Execution:Stoptest ACDCP:NAME=RACK:0/ACDCP:0;
UNLOCK ACDCP
Command Tree:“MANAGED-ELEMENT h BSS-EQUIPMENT h BTSEP h RACK h ACDCP h UNLOCK ACDCP”
Applicability:Phase 2 and Phase 3.
Visibility level: 1.
Command Description:This command changes the administrative state of AC/DC converter.
Long Names:NAME Address of the managed object
System Responses:Operation Completed
The specified change of administrative state has been perfomed:
JOB: 34
PC Time&Date: 11:55:18 03/23/2005
NE Time&Date: 12:56:53 09/15/2004
USER NAME: NSN
COMMAND: Unlock ACDCP:NAME=RACK:0/ACDCP:0;
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: Operation successful
administrativeState = Unlocked
END OF OUTPUT FOR JOB 34
CHANGED STATE EVENT REPORT:
UNLOCK ACDCP NAME=RACK:0..7/ACDCP:0..1;
DN0933412 Issue 0163
BTSplus mainline commands at the Flexi BSC product family
ACDCP
Id:0900d805805b0cac
This provides information about the administrative state, the operational state and the availability status every time a state change occurs:
JOB: 35
PC Time&Date: 11:55:18 03/23/2005
NE Time&Date: 12:56:53 09/15/2004
USER NAME: NSN
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: Operation successful
CHANGED STATE EVENT REPORT:
NAME = RACK:0/ACDCP:0
Administrative State = UNLOCKED
Notification Identifier = 280
END OF OUTPUT FOR JOB 35
Operation Failed
The specified change of administrative state has not been performed.
Application Guidelines:
• The ACDCP can not be unlocked for the BS-240 Compact Site as it is equipped in the Energy Station Rack which is not supervised by the SW
• The ACDCP can not be unlocked for the BS-40II
Example of Command Execution:Unlock ACDCP:NAME=RACK:0/ACDCP:0;
64DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805b0cae
ACT
ACTThe ACT (Alarm Collection Terminal) object represents the terminal for all alarms col-lection.
CREATE ACT
Command Tree:“MANAGED-ELEMENT h BSS-EQUIPMENT h BTSEP h RACK h ACT h CREATE ACT”
Applicability:Phase 2 and Phase 3.
Visibility level: 2.
Command Description:This command adds the ACT (Alarm Collection Terminal) to the BTSE data base. The ACT contains the interface to the external alarms (Operator alarms, rack alarms, shelter alarms,...) and commands and a CAN-BUS interface to the CORE.
Long Names:NAME Address of the managed object
System Responses:Operation Completed
After command execution, a message of Changed Configuration Notification is dis-played. A further message indicates the result of the operation. An example of create command is the following:
JOB: 187
PC Time&Date: 16:48:48 03/23/2005
NE Time&Date: 16:46:42 09/15/2004
USER NAME: NSN
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: Operation successful
ChangedConfigurationNotification:
name = RACK:0/ACT:0
ChangeInfo = created
CREATE ACT NAME=RACK:0..7/ACT:0..0;
DN0933412 Issue 0165
BTSplus mainline commands at the Flexi BSC product family
ACT
Id:0900d805805b0cae
END OF OUTPUT FOR JOB 187
JOB: 188
PC Time&Date: 16:48:48 03/23/2005
NE Time&Date: 16:46:42 09/15/2004
USER NAME: NSN
COMMAND: Create ACT:NAME=RACK:0/ACT:0;
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: Operation successful
END OF OUTPUT FOR JOB 188
Operation Failed
The specified Object has not been created. In addition to the general NACK causes, a specific NACK cause, which indicates that the command is inconsistent with the physical configuration, is possible. An example is the following:
JOB: 72
PC Time&Date: 16:37:54 03/23/2005
NE Time&Date: 16:35:47 09/15/2004
USER NAME: NSN
COMMAND: Create ACT:NAME=RACK:0/ACT:0;
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: OPERATION FAILED
Message cannot be performed (-17)
END OF OUTPUT FOR JOB 72
Application Guidelines:
• The ACTC which is a part of the DC Panel and it is always present in every rack to collect all internal alarms. It has inputs for 16 internal alarms (1 Door, 6 Fans and 9 rack/shelter internal alarms, which can be defined by the operator). The ACTC supports 9 ENVAs within the range from 0...8. BS82II support 5 internal alarms (1 Door, 1 Fans and 3 rack/shelter internal alarms, which can be defined by the oper-ator)
66DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805b0cae
ACT
• An ACTM for 48 alarms and 8 commands is used only in the Base Rack to support the external alarm and command interface for the operator. The ACTM consists of two boards: the ACTA (Alarm and Command Interfaces) and the ACTP (Processor Core). The ACTP sends the alarms to the CORE via the CAN BUS
• For the Extension Racks and the Service Racks only few alarms (e.g. temperature supervision, FAN, ACDC alarms,..) are necessary, so an ACTP with 16 alarm or site inputs is used. The ACTP sends the alarms to the CORE via the CAN BUS
• On a BS82II (base and extension racks) temp., RDO, FAN alarms are controlled by the ACT (on other platforms from COBA in Base rack), these inputs are only handled in a correct way if the ACT is created successfully
Example of Command Execution:Create ACT:NAME=RACK:0/ACT:0;
DELETE ACT
Command Tree:“MANAGED-ELEMENT h BSS-EQUIPMENT h BTSEP h RACK h ACT h DELETE ACT”
Applicability:Phase 2 and Phase 3.
Visibility level: 2.
Command Description:This command deletes the ACT (Alarm Collection Terminal) from the BTSE data base.
Long Names:NAME Address of the managed object
System Responses:Operation Completed
After command execution, a message of Changed Configuration Notification is dis-played. A further message indicates the result of the operation. An example of create command is the following:
JOB: 196
PC Time&Date: 16:49:26 03/23/2005
NE Time&Date: 16:47:20 09/15/2004
USER NAME: NSN
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: Operation successful
DELETE ACT NAME=RACK:0..7/ACT:0..0;
DN0933412 Issue 0167
BTSplus mainline commands at the Flexi BSC product family
ACT
Id:0900d805805b0cae
ChangedConfigurationNotification:
name = RACK:0/ACT:0
ChangeInfo = deleted
END OF OUTPUT FOR JOB 196
JOB: 197
PC Time&Date: 16:49:26 03/23/2005
NE Time&Date: 16:47:20 09/15/2004
USER NAME: NSN
COMMAND: Delete ACT:NAME=RACK:0/ACT:0;
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: Operation successful
END OF OUTPUT FOR JOB 197
Operation Failed
The specified object has not been deleted. Additionally to the general NACK causes, a specific NACK cause, meaning that the command is inconsistent with physical configu-ration, is possible.
Application Guidelines:
• ACT must be locked in phase 3 before deletion
Example of Command Execution:Delete ACT:NAME=RACK:0/ACT:0;
GET ACT
Command Tree:“MANAGED-ELEMENT h BSS-EQUIPMENT h BTSEP h RACK h ACT h GET ACT”
Applicability:Phase 2 and Phase 3.
Visibility level: 0.
GET ACT NAME=RACK:0..7/ACT:0..0 [,REQATTL=ALS, AST, AVS, OST, PRS, RELFUNCOBJ];
68DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805b0cae
ACT
Command Description:This command displays the attributes of the ACT (Alarm Collection Terminal).
Long Names:NAME Address of the managed object
REQATTL Required attribute list
ALS alarmStatus
AST administrativeState
AVS availabilityStatus
OST operationalState
PRS proceduralStatus
RELFUNCOBJ relatedFuncObjects
System Responses:Operation Completed
A message indicates the result of the operation. An example of get command is the fol-lowing:
JOB: 189
PC Time&Date: 16:49:05 03/23/2005
NE Time&Date: 16:46:59 09/15/2004
USER NAME: NSN
COMMAND: Get ACT:NAME=RACK:0/ACT:0;
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: Operation successful
alarmStatus = CLEARED
administrativeState = Unlocked
availabilityStatus = NotInstalled
operationalState = DISABLED
proceduralStatus = NULL
relatedFuncObjects =
END OF OUTPUT FOR JOB 189
Operation Failed
The GET command has not been successfully executed. A general NACK will indicate possible errors or a specific NACK strictly related to the single command is possible.
Application Guidelines:None.
DN0933412 Issue 0169
BTSplus mainline commands at the Flexi BSC product family
ACT
Id:0900d805805b0cae
Example of Command Execution:Get ACT:NAME=RACK:0/ACT:0,REQATTL=ALS&AST&AVS&OST&
PRS&RELFUNCOBJ;
GETTEST ACT
Command Tree:“MANAGED-ELEMENT h BSS-EQUIPMENT h BTSEP h RACK h ACT h GETTEST ACT”
Applicability:Phase 2 and Phase 3.
Visibility level: 0.
Command Description:This command displays the attributes of the ACT (Alarm Collection Terminal) test.
Long Names:NAME Address of the managed object
REQATTL Required attribute list
System Responses:Operation Completed
A message indicates the result of the operation. An example of gettest command is the following:
JOB: 26
PC Time&Date: 11:55:09 03/23/2005
NE Time&Date: 12:56:44 09/15/2004
USER NAME: NSN
COMMAND: Gettest ACT:NAME=RACK:0/ACT:0;
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: Operation successful
MOT = RACK:0/ACT:0
testMonitor =
phaseId = PreliminaryTestsAct
phaseStatus = Running
phaseId = CheckAlarmStatusAct
phaseStatus = Waiting
GETTEST ACT NAME=RACK:0..7/ACT:0..0;
70DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805b0cae
ACT
phaseId = EndTestAct
phaseStatus = Waiting
testOutcome = INCONCLUSIVE
testState = INITIALIZING
END OF OUTPUT FOR JOB 26
Operation Failed
The GET command has not been successfully executed. A general NACK will indicate possible errors or a specific NACK strictly related to the single command is possible.
Application Guidelines:None.
Example of Command Execution:Gettest ACT:NAME=RACK:0/ACT:0,REQATTL=ALS&AST&AVS&OST&PRS;
LOCK ACT
Command Tree:“MANAGED-ELEMENT h BSS-EQUIPMENT h BTSEP h RACK h ACT h LOCK ACT”
Applicability:Phase 2 and Phase 3.
Visibility level: 1.
testMonitor it is a list of all test phases related to the selected object; for each phase the related phaseStatus is provided (Passed, Failed, Running or Waiting).
phaseId =
phaseStatus =
phaseId =
phaseStatus =
...
...
testOutcome It represents the test result: it can be Inconclusive (if the phases already executed were successful) or Fail (if at least one of the executed phases failed).
testState = Testing It can assume one of the following values: not_initialized, idle, initializing, sus-pended, testing, terminating and dis-abled.
LOCK ACT NAME=RACK:0..7/ACT:0..0;
DN0933412 Issue 0171
BTSplus mainline commands at the Flexi BSC product family
ACT
Id:0900d805805b0cae
Command Description:This command changes the administrative state of ACT (Alarm Collection Terminal).
Long Names:NAME Address of the managed object
System Responses:Operation Completed
The specified change of administrative state has been perfomed:
JOB: 190
PC Time&Date: 16:49:10 03/23/2005
NE Time&Date: 16:47:04 09/15/2004
USER NAME: NSN
COMMAND: Lock ACT:NAME=RACK:0/ACT:0;
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: Operation successful
administrativeState = Locked
END OF OUTPUT FOR JOB 190
CHANGED STATE EVENT REPORT:
This provides information about the administrative state, the operational state and the availability status every time a state change occurs:
JOB: 191
PC Time&Date: 16:49:10 03/23/2005
NE Time&Date: 16:47:04 09/15/2004
USER NAME: NSN
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: Operation successful
CHANGED STATE EVENT REPORT:
NAME = RACK:0/ACT:0
72DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805b0cae
ACT
Administrative State = LOCKED
Notification Identifier = 566
END OF OUTPUT FOR JOB 191
Operation Failed
The specified change of administrative state has not been performed.
Application Guidelines:None.
Example of Command Execution:Lock ACT:NAME=RACK:0/ACT:0;
PERFTEST ACT
Command Tree:“MANAGED-ELEMENT h BSS-EQUIPMENT h BTSEP h RACK h ACT h PERFTEST ACT”
Applicability:Phase 2 and Phase 3.
Visibility level: 1.
Command Description:This command changes the administrative state of ACT (Alarm Collection Terminal).
Long Names:NAME Address of the managed object
System Responses:Operation Completed
Test configuration has been set and the specified test has been started. The System response will not be addressed to the MOT but to the object BTSEP.
JOB: 36
PC Time&Date: 11:55:22 03/23/2005
NE Time&Date: 12:56:57 09/15/2004
USER NAME: NSN
COMMAND: Perftest ACT:NAME=RACK:0/ACT:0;
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: Operation successful
PERFTEST ACT NAME=RACK:0..7/ACT:0..0;
DN0933412 Issue 0173
BTSplus mainline commands at the Flexi BSC product family
ACT
Id:0900d805805b0cae
MOT = RACK:0/ACT:0
tO = BTSETEST:2
END OF OUTPUT FOR JOB 36
JOB: 37
PC Time&Date: 11:55:22 03/23/2005
NE Time&Date: 12:56:57 09/15/2004
USER NAME: NSN
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: Operation successful
ChangedConfigurationNotification:
name = BTSETEST:2
ChangeInfo = created
END OF OUTPUT FOR JOB 37
JOB: 38
PC Time&Date: 11:55:25 03/23/2005
NE Time&Date: 12:57:00 09/15/2004
USER NAME: NSN
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: Operation successful
CHANGED STATE EVENT REPORT:
NAME = RACK:0/ACT:0
Operational State = ENABLED
Availability Status = NULL_value
Notification Identifier = 128
74DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805b0cae
ACT
END OF OUTPUT FOR JOB 38
JOB: 39
PC Time&Date: 11:55:25 03/23/2005
NE Time&Date: 12:57:00 09/15/2004
USER NAME: NSN
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: Operation successful
Test Report:
name = BTSETEST:2
testOutcome = PASSED
testTermination = Normal
MOT = RACK:0/ACT:0
executedPhases =
PreliminaryTestsAct
CheckAlarmStatusAct
EndTestAct
END OF OUTPUT FOR JOB 39
JOB: 40
PC Time&Date: 11:55:28 03/23/2005
NE Time&Date: 12:57:03 09/15/2004
USER NAME: NSN
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: Operation successful
ChangedConfigurationNotification:
name = BTSETEST:2
ChangeInfo = deleted
END OF OUTPUT FOR JOB 40
DN0933412 Issue 0175
BTSplus mainline commands at the Flexi BSC product family
ACT
Id:0900d805805b0cae
Operation Failed
This NACK-message occurs in the following cases: Message cannot be performed, test not supported, capacity restrictions, physical configuration cannot be performed, object not locked.
Application Guidelines:
• In phase 3 MO must be locked previous to the command execution
The test results will be displayed at the end of the test phases.
Result TEST:
name = TEST:<n>
testOutcome = This field represents the test result; one of the fol-lowing values can be displayed:
Pass all the test phases are successfully performed.
Inconclusive the test is aborted by the system or the test is terminated by the opera-tor.
Fail if at least one of the executed phases fail.
mOts = It is the identifier of the hardware object under test.
testTermination = It specifies how the test is terminated, it can assume the following values:
Normal all the test phases are performed.
Abort the test is aborted by system.
Cancel the test is terminated by operator.
executedPhases
phaseId = It represents the list of the executed test phases (in case of successful test result, all the test phases will be listed).
additionalWords =
....
failedPhases
phaseId = It represents the list of the failed test phase; addi-tional information is provided for each phase.phaseId =
....
skippedPhases
phaseId = It represents the list of the skipped phases; they are displayed only for test stopped during it execution.phaseId =
....
poprosedRepair Action =
A list of most probable fail probable causes is shown (max four messages)
76DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805b0cae
ACT
Example of Command Execution:Perftest ACT:NAME=RACK:0/ACT:0;
STOPTEST ACT
Command Tree:“MANAGED-ELEMENT h BSS-EQUIPMENT h BTSEP h RACK h ACT h STOPTEST ACT”
Applicability:Phase 2 and Phase 3.
Visibility level: 1.
Command Description:This command is used to stop a diagnostic previously started.
Long Names:NAME Address of the managed object
System Responses:Operation Completed
Test has been stopped. The System Responses will not be addressed to the MOT but to the object BTSEP.
STOPTEST ACT NAME=RACK:0..7/ACT:0..0;
Result TEST:
name = TEST:<n>
testOutcome = inconclusive
mOts = It is the identifier of the hardware object under test.
testTermination = Cancel
executedPhases
phaseId = It represents the list of the executed test phases; the list is not shown for test in the waiting list (queued)....
.
failedPhases
phaseId = It represents the list of the failed test phase;
additional information is provided for each phase.phaseId =
....
skippedPhases
phaseId = It represents the list of the skipped phases;the list is not shown for test in the waiting list (queued).phaseId =
DN0933412 Issue 0177
BTSplus mainline commands at the Flexi BSC product family
ACT
Id:0900d805805b0cae
Operation Failed
Test has not been stopped. This NACK-message can occur when the specified test is not running or in case of test which cannot be stopped.
Application Guidelines:None.
Example of Command Execution:Stoptest ACT:NAME=RACK:0/ACT:0;
UNLOCK ACT
Command Tree:“MANAGED-ELEMENT h BSS-EQUIPMENT h BTSEP h RACK h ACT h UNLOCK ACT”
Applicability:Phase 2 and Phase 3.
Visibility level: 1.
Command Description:This command changes the administrative state of ACT (Alarm Collection Terminal).
Long Names:NAME Address of the managed object
System Responses:Operation Completed
The specified change of administrative state has been perfomed:
JOB: 192
PC Time&Date: 16:49:15 03/23/2005
NE Time&Date: 16:47:09 09/15/2004
USER NAME: NSN
COMMAND: Unlock ACT:NAME=RACK:0/ACT:0;
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: Operation successful
administrativeState = Unlocked
END OF OUTPUT FOR JOB 192
UNLOCK ACT NAME=RACK:0..7/ACT:0..0;
78DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805b0cae
ACT
CHANGED STATE EVENT REPORT:
This provides information about the administrative state, the operational state and the availability status every time a state change occurs:
JOB: 193
PC Time&Date: 16:49:15 03/23/2005
NE Time&Date: 16:47:09 09/15/2004
USER NAME: NSN
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: Operation successful
CHANGED STATE EVENT REPORT:
NAME = RACK:0/ACT:0
Administrative State = UNLOCKED
Notification Identifier = 567
END OF OUTPUT FOR JOB 193
Operation Failed
The specified change of administrative state has not been performed.
Application Guidelines:None.
Example of Command Execution:Unlock ACT:NAME=RACK:0/ACT:0;
DN0933412 Issue 0179
BTSplus mainline commands at the Flexi BSC product family
BATTERY
Id:0900d805805b0cb0
BATTERYOne backup battery system can be connected to the AC/DC sub-rack. The battery system consists of up to four batteries optionally housed in the battery sub-rack. The DC and Battery Controller (DCBCTRL) installed in the AC/DC subrack is the supervision unit which provides for the Batteries charging.
CREATE BATTERY
Command Tree:“MANAGED-ELEMENT h BSS-EQUIPMENT h BTSEP h RACK h BATTERY h CREATE BATTERY”
Applicability:Phase 2 and Phase 3.
Visibility level: 2.
Command Description:This command adds the BATTERY (which provides battery backup) to the BTSE data base.
Long Names:NAME Address of the managed object
System Responses:Operation Completed
After command execution, a message of Changed Configuration Notification is dis-played. A further message indicates the result of the operation. An example of create command is the following:
JOB: 21
PC Time&Date: 11:54:46 03/23/2005
NE Time&Date: 12:56:21 09/15/2004
USER NAME: NSN
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: Operation successful
ChangedConfigurationNotification:
name = RACK:0/BATTERY:0
ChangeInfo = created
CREATE BATTERY NAME=RACK:0..7/BATTERY:0..3;
80DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805b0cb0
BATTERY
END OF OUTPUT FOR JOB 21
JOB: 22
PC Time&Date: 11:54:47 03/23/2005
NE Time&Date: 12:56:22 09/15/2004
USER NAME: NSN
COMMAND: Create BATTERY:NAME=RACK:0/BATTERY:0;
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: Operation successful
END OF OUTPUT FOR JOB 22
Operation Failed
The specified Object has not been created. In addition to the general NACK causes, a specific NACK cause, which indicates that the command is inconsistent with the physical configuration, is possible. An example is the following:
JOB: 23
PC Time&Date: 11:55:04 03/23/2005
NE Time&Date: 12:56:39 09/15/2004
USER NAME: NSN
COMMAND: Create BATTERY:NAME=RACK:0/BATTERY:0;
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: OPERATION FAILED
MO already created (-159)
END OF OUTPUT FOR JOB 23
Application Guidelines:
• The AC/DC is necessary for the charging and supervising of the battery backup system
• When a service environment (AC/DC + Battery Backup) is built on at BS60 sites, after replacement of BS60 with BS-240 a special setting of the attribute "associat-edString" in the command "CREATE ENVABTSE" for the corresponding site input allows the operator to indicate that the support of emergency configuration is
DN0933412 Issue 0181
BTSplus mainline commands at the Flexi BSC product family
BATTERY
Id:0900d805805b0cb0
required for battery backup unit system (Emergency Configuration after AC fault of 3rd party Service Rack)
• The BATTERY can not be created for the BS-240 Compact Site as it is equipped in the Battery Backup Rack and Energy Station Rack which are not supervised by the SW. In the BS-240 implementation the switch into emergency configuration (due to a battery discharge alarm) is triggered by an "ALARM STATUS" CAN bus message that has been received from the CAN node of the AC/DC controller. In the BS-240 Compact Site the AC/DC alarm line for the AC/DC converter and for the battery must be connected to a site input which is used as a trigger for the emergency configura-tion. A special setting of the attribute "associatedString" in the command "CREATE ENVABTSE" for the corresponding site input allows the operator to indicate that the support of emergency configuration is required for the 3rd party battery backup unit system.
• The BATTERY can not be created for the BS-40II.
Example of Command Execution:Create BATTERY:NAME=RACK:0/BATTERY:0;
DELETE BATTERY
Command Tree:“MANAGED-ELEMENT h BSS-EQUIPMENT h BTSEP h RACK h BATTERY h DELETE BATTERY”
Applicability:Phase 2 and Phase 3.
Visibility level: 2.
Command Description:This command deletes the BATTERY (which provides battery backup) from the BTSE data base.
Long Names:NAME Address of the managed object
System Responses:Operation Completed
After command execution, a message of Changed Configuration Notification is dis-played. A further message indicates the result of the operation. An example of delete command is the following:
JOB: 19
PC Time&Date: 11:54:44 03/23/2005
NE Time&Date: 12:56:19 09/15/2004
DELETE BATTERY NAME=RACK:0..7/BATTERY:0..3;
82DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805b0cb0
BATTERY
USER NAME: NSN
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: Operation successful
ChangedConfigurationNotification:
name = RACK:0/BATTERY:0
ChangeInfo = deleted
END OF OUTPUT FOR JOB 19
JOB: 20
PC Time&Date: 11:54:44 03/23/2005
NE Time&Date: 12:56:19 09/15/2004
USER NAME: NSN
COMMAND: Delete BATTERY:NAME=RACK:0/BATTERY:0;
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: Operation successful
END OF OUTPUT FOR JOB 20
Operation Failed
The specified Object has not been deleted. Additionally to the general NACK causes, a specific NACK cause, meaning that the command is inconsistent with physical configu-ration, is possible.
Application Guidelines:
• BATTERY must be locked in phase 3 before deletion
• The BATTERY can not be deleted for the BS-240 Compact Site as it is equipped in the Battery Backup Rack and Energy Station Rack which are not supervised by the SW
• The BATTERY can not be deleted for the BS-40II
Example of Command Execution:Delete BATTERY:NAME=RACK:0/BATTERY:0;
GET BATTERYGET BATTERY NAME=RACK:0..7/BATTERY:0..3 [,REQATTL=ALS, AST,
AVS, BATTCAP, OST, PRS, RELFUNCOBJ];
DN0933412 Issue 0183
BTSplus mainline commands at the Flexi BSC product family
BATTERY
Id:0900d805805b0cb0
Command Tree:“MANAGED-ELEMENT h BSS-EQUIPMENT h BTSEP h RACK h BATTERY h GET BATTERY”
Applicability:Phase 2 and Phase 3.
Visibility level: 0.
Command Description:This command displays the attributes of the BATTERY.
Long Names:NAME Address of the managed object
REQATTL Required attribute list
ALS alarmStatus
AST administrativeState
AVS availabilityStatus
BATTCAP batteryCapacity(*5Ah)
OST operationalState
PRS proceduralStatus
RELFUNCOBJ relatedFuncObjects
System Responses:Operation Completed
After command execution, a message indicates the result of the operation. An example of get command is the following:
JOB: 5
PC Time&Date: 11:54:18 03/23/2005
NE Time&Date: 12:55:53 09/15/2004
USER NAME: NSN
COMMAND: Get BATTERY:NAME=RACK:0/BATTERY:0;
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: Operation successful
alarmStatus = CLEARED
administrativeState = Unlocked
availabilityStatus = NULL
batteryCapacity(*5Ah) = 3
operationalState = ENABLED
84DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805b0cb0
BATTERY
proceduralStatus = NULL
relatedFuncObjects =
END OF OUTPUT FOR JOB 5
Operation Failed
The GET command has not been successfully executed. A general NACK will indicate possible errors or a specific NACK strictly related to the single command is possible.
Application Guidelines:
• The GET BATTERY command can not be issued for the BS-240 Compact Site as the BATTERY is equipped in the Battery Backup Rack and Energy Station Rack which are not supervised by the SW
• The GET BATTERY command can not be issued for the BS-40II
Example of Command Execution:Get BATTERY:NAME=RACK:0/BATTERY:0,REQATTL=ALS&AST&AVS&
BATTCAP&OST&PRS&RELFUNCOBJ;
GETTEST BATTERY
Command Tree:“MANAGED-ELEMENT h BSS-EQUIPMENT h BTSEP h RACK h BATTERY h GETTEST BATTERY”
Applicability:Phase 2 and Phase 3.
Visibility level: 0.
Command Description:This command displays the attributes of the BATTERY test.
Long Names:NAME Address of the managed object
REQATTL Required attribute list
System Responses:Operation Completed
After command execution, a message indicates the result of the operation. An example of gettest command is the following:
JOB: 14
PC Time&Date: 11:54:31 03/23/2005
GETTEST BATTERY NAME=RACK:0..7/BATTERY:0..3;
DN0933412 Issue 0185
BTSplus mainline commands at the Flexi BSC product family
BATTERY
Id:0900d805805b0cb0
NE Time&Date: 12:56:06 09/15/2004
USER NAME: NSN
COMMAND: Gettest BATTERY:NAME=RACK:0/BATTERY:0;
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: Operation successful
MOT = RACK:0/BATTERY:0
testMonitor =
phaseId = PreliminaryTestsBattery
phaseStatus = Running
phaseId = CheckAlarmStatusBattery
phaseStatus = Waiting
phaseId = EndTestBattery
phaseStatus = Waiting
testOutcome = INCONCLUSIVE
testState = INITIALIZING
END OF OUTPUT FOR JOB 14
Operation Failed
The GET command has not been successfully executed. A general NACK will indicate possible errors or a specific NACK strictly related to the single command is possible.
Application Guidelines:None.
testMonitor it is a list of all test phases related to the selected object; for each phase the related phaseStatus is provided (Passed, Failed, Running or Waiting).
phaseId =
phaseStatus =
phaseId =
phaseStatus =
...
...
testOutcome It represents the test result: it can be Inconclusive (if the phases already executed were successful) or Fail (if at least one of the executed phases failed).
testState = Testing It can assume one of the following values: not_initialized, idle, initializing, sus-pended, testing, terminating and dis-abled.
86DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805b0cb0
BATTERY
Example of Command Execution:Gettest BATTERY:NAME=RACK:0/BATTERY:0;
LOCK BATTERY
Command Tree:“MANAGED-ELEMENT h BSS-EQUIPMENT h BTSEP h RACK h BATTERY h LOCK BATTERY”
Applicability:Phase 2 and Phase 3.
Visibility level: 1.
Command Description:This command changes the administrative state of the BATTERY (which provides battery backup).
Long Names:NAME Address of the managed object
System Responses:Operation Completed
The specified change of administrative state has been perfomed:
JOB: 6
PC Time&Date: 11:54:22 03/23/2005
NE Time&Date: 12:55:57 09/15/2004
USER NAME: NSN
COMMAND: Lock BATTERY:NAME=RACK:0/BATTERY:0;
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: Operation successful
administrativeState = Locked
END OF OUTPUT FOR JOB 6
CHANGED STATE EVENT REPORT:
This provides information about the administrative state, the operational state and the availability status every time a state change occurs:
LOCK BATTERY NAME=RACK:0..7/BATTERY:0..3;
DN0933412 Issue 0187
BTSplus mainline commands at the Flexi BSC product family
BATTERY
Id:0900d805805b0cb0
JOB: 7
PC Time&Date: 11:54:22 03/23/2005
NE Time&Date: 12:55:57 09/15/2004
USER NAME: NSN
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: Operation successful
CHANGED STATE EVENT REPORT:
NAME = RACK:0/BATTERY:0
Administrative State = LOCKED
Notification Identifier = 263
END OF OUTPUT FOR JOB 7
Operation Failed
The specified change of administrative state has not been performed (e.g. the object is redundant and its spare copy is disabled or already locked, a subordinate resource cannot go into disabled state with "dependency" availability status).
Application Guidelines:
• The BATTERY can not be locked for the BS-240 Compact Site as it is equipped in the Battery Backup Rack and Energy Station Rack which are not supervised by the SW
• The BATTERY can not be locked for the BS-40II
Example of Command Execution:Lock BATTERY:NAME=RACK:0/BATTERY:0;
PERFTEST BATTERY
Command Tree:“MANAGED-ELEMENT h BSS-EQUIPMENT h BTSEP h RACK h BATTERY h PERFTEST BATTERY”
Applicability:Phase 2 and Phase 3.
Visibility level: 1.
PERFTEST BATTERY NAME=RACK:0..7/BATTERY:0..3;
88DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805b0cb0
BATTERY
Command Description:This command requests the execution of a test performed by the BATTERY (which provides battery backup).
Long Names:NAME Address of the managed object
System Responses:Operation Completed
Test configuration has been set and the specified test has been started. The System response will not be addressed to the MOT but to the object BTSEP.
JOB: 9
PC Time&Date: 11:54:26 03/23/2005
NE Time&Date: 12:56:01 09/15/2004
USER NAME: NSN
COMMAND: Perftest BATTERY:NAME=RACK:0/BATTERY:0;
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: Operation successful
MOT = RACK:0/BATTERY:0
tO = BTSETEST:2
END OF OUTPUT FOR JOB 9
JOB: 10
PC Time&Date: 11:54:26 03/23/2005
NE Time&Date: 12:56:01 09/15/2004
USER NAME: NSN
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: Operation successful
ChangedConfigurationNotification:
name = BTSETEST:2
ChangeInfo = created
DN0933412 Issue 0189
BTSplus mainline commands at the Flexi BSC product family
BATTERY
Id:0900d805805b0cb0
END OF OUTPUT FOR JOB 10
JOB: 11
PC Time&Date: 11:54:26 03/23/2005
NE Time&Date: 12:56:01 09/15/2004
USER NAME: NSN
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: Operation successful
CHANGED STATE EVENT REPORT:
NAME = RACK:0/BATTERY:0
Operational State = ENABLED
Availability Status = NULL_value
Notification Identifier = 267
END OF OUTPUT FOR JOB 11
JOB: 12
PC Time&Date: 11:54:26 03/23/2005
NE Time&Date: 12:56:01 09/15/2004
USER NAME: NSN
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: Operation successful
Test Report:
name = BTSETEST:2
testOutcome = PASSED
testTermination = Normal
MOT = RACK:0/BATTERY:0
executedPhases =
PreliminaryTestsBattery
CheckAlarmStatusBattery
EndTestBattery
90DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805b0cb0
BATTERY
END OF OUTPUT FOR JOB 12
JOB: 13
PC Time&Date: 11:54:26 03/23/2005
NE Time&Date: 12:56:01 09/15/2004
USER NAME: NSN
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: Operation successful
ChangedConfigurationNotification:
name = BTSETEST:2
ChangeInfo = deleted
END OF OUTPUT FOR JOB 13
The test results will be displayed at the end of the test phases.
Result TEST:
name = TEST:<n>
testOutcome = This field represents the test result; one of the fol-lowing values can be displayed:
Pass all the test phases are successfully performed.
Inconclusive the test is aborted by the system or the test is terminated by the opera-tor.
Fail if at least one of the executed phases fail.
mOts = It is the identifier of the hardware object under test.
testTermination = It specifies how the test is terminated, it can assume the following values:
Normal all the test phases are performed.
Abort the test is aborted by system.
Cancel the test is terminated by operator.
executedPhases
phaseId = It represents the list of the executed test phases (in case of successful test result, all the test phases will be listed).
additionalWords =
....
DN0933412 Issue 0191
BTSplus mainline commands at the Flexi BSC product family
BATTERY
Id:0900d805805b0cb0
Operation Failed
This NACK-message occurs in the following cases: Message cannot be performed, test not supported, capacity restrictions, physical configuration cannot be performed, object not locked.
Application Guidelines:
• In phase 3 MO must be locked previous to the command execution
Example of Command Execution:Perftest BATTERY:NAME=RACK:0/BATTERY:0;
STOPTEST BATTERY
Command Tree:“MANAGED-ELEMENT h BSS-EQUIPMENT h BTSEP h RACK h BATTERY h STOPTEST BATTERY”
Applicability:Phase 2 and Phase 3.
Visibility level: 1.
Command Description:This command is used to stop a diagnostic previously started.
Long Names:NAME Address of the managed object
System Responses:Operation Completed
Test has been stopped. The System Responses will not be addressed to the MOT but to the object BTSEP.
failedPhases
phaseId = It represents the list of the failed test phase; addi-tional information is provided for each phase.phaseId =
....
skippedPhases
phaseId = It represents the list of the skipped phases; they are displayed only for test stopped during it execution.phaseId =
....
poprosedRepair Action =
A list of most probable fail probable causes is shown (max four messages)
STOPTEST BATTERY NAME=RACK:0..7/BATTERY:0..3;
92DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805b0cb0
BATTERY
Operation Failed
Test has not been stopped. This NACK-message can occur when the specified test is not running or in case of test which cannot be stopped.
Application Guidelines:None.
Example of Command Execution:Stoptest BATTERY:NAME=RACK:0/BATTERY:0;
UNLOCK BATTERY
Command Tree:“MANAGED-ELEMENT h BSS-EQUIPMENT h BTSEP h RACK h BATTERY h UNLOCK BATTERY”
Applicability:Phase 2 and Phase 3.
Visibility level: 1.
Command Description:This command changes the administrative state of the BATTERY (which provides battery backup).
Result TEST:
name = TEST:<n>
testOutcome = inconclusive
mOts = It is the identifier of the hardware object under test.
testTermination = Cancel
executedPhases
phaseId = It represents the list of the executed test phases; the list is not shown for test in the waiting list (queued)....
.
failedPhases
phaseId = It represents the list of the failed test phase;
additional information is provided for each phase.phaseId =
....
skippedPhases
phaseId = It represents the list of the skipped phases;the list is not shown for test in the waiting list (queued).phaseId =
UNLOCK BATTERY NAME=RACK:0..7/BATTERY:0..3;
DN0933412 Issue 0193
BTSplus mainline commands at the Flexi BSC product family
BATTERY
Id:0900d805805b0cb0
Long Names:NAME Address of the managed object
System Responses:Operation Completed
The specified change of administrative state has been perfomed:
JOB: 15
PC Time&Date: 11:54:35 03/23/2005
NE Time&Date: 12:56:10 09/15/2004
USER NAME: NSN
COMMAND: Unlock BATTERY:NAME=RACK:0/BATTERY:0;
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: Operation successful
administrativeState = Unlocked
END OF OUTPUT FOR JOB 15
CHANGED STATE EVENT REPORT:
This provides information about the administrative state, the operational state and the availability status every time a state change occurs:
JOB: 16
PC Time&Date: 11:54:35 03/23/2005
NE Time&Date: 12:56:10 09/15/2004
USER NAME: NSN
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: Operation successful
CHANGED STATE EVENT REPORT:
NAME = RACK:0/BATTERY:0
Administrative State = UNLOCKED
Notification Identifier = 268
94DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805b0cb0
BATTERY
END OF OUTPUT FOR JOB 16
Operation Failed
The specified change of administrative state has not been performed.
Application Guidelines:
• The BATTERY can not be unlocked for the BS-240 Compact Site as it is equipped in the Battery Backup Rack and Energy Station Rack which are not supervised by the SW
• The BATTERY can not be unlocked for the BS-40II
Example of Command Execution:Unlock BATTERY:NAME=RACK:0/BATTERY:0;
DN0933412 Issue 0195
BTSplus mainline commands at the Flexi BSC product family
BCOM
Id:0900d805805b0cb2
BCOMThe BCOM (Combining Module) is an equipment object that represents the combining module supporting up to 6 TRX, all within the same frequency band. The BCOM has no CAN bus interface and therefore cannot provide the remote inventory data onboard. New BCOM element shall be handled via IDF editor from LMT Evolution. No ACT-C is supported.
MDUX (a small BCOM 6:6) and HYBRID6 can replace FDUAMCOs. MDUX can fit into 2 adjacent ACOM slots of BTSplus mainline rack. If more than 6 transceivers are required, the HYBRID6 module, containing 6 hybrids and isolators, has to be addition-ally equipped. This module fits either in a BCOM slot (along with a MDUX) or in an ACOM- respectively MUCO-slot of the BTSplus mainline rack.
The alarm interface of the MDUX is identical and fully compatible to the BCOM, while the HYBRID6 is a completely passive module with only RF interfaces. It is therefore not visible for the software.
The 6:6 combining of the MDUX allows single rack cell configurations which cannot be supported with the existing combining equipment. With 2 MDUX equipped in a single BS240 II rack a 2/2/2 dual band configuration becomes possible.
All inventory units of the optional Service Rack are nob_RIUs which have to be regis-tered via LMT Evolution and IDF editor.
g BCOM command is valid only for BS240 and BS240XL.
The configurations BCOM (MDUX) + HYBRID6 +COAMCO are possible.
The maximum number of carrier unit ports, which are connected to the RX outputs of an MDUX submodule is:
• 4 for MDUX only equipped
• 8 for MDUX and COAMCO equipped.
The maximum number of carrier unit ports which are either directly or via HYBRID6 con-nected to the TX input of an MDUX submodule is:
• 1 for MDUX without HYBRID6 equipped
• 2 for MDUX with HYBRID6 equipped
• 4 for MDUX with HYBRID6 and COAMCO equipped
CREATE BCOM
Command Tree:“MANAGED-ELEMENT h BSS-EQUIPMENT h BTSEP h RACK h BCOM h CREATE BCOM”
CREATE BCOM NAME=RACK:0..7/BCOM:0..1 [,ANT<x>CELLNO=] [,ANT<x>SCNRX=] ,ACONN= [,FBAND=] [,BCOMTYPE=];
96DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805b0cb2
BCOM
Applicability:Phase 2 and Phase 3.
Visibility level: 2.
Command Description:This command is used to create the instances 0 and 1 of BCOM object.
In this CREATE command cell number, an alarm connector or frequency band of Bcom can be specified.
Furthermore SetWiringRx BCOM and SetWiringTx BCOM commands have to be used to specify the wiring data. Alarm connector parameter is mandatory at the creation of BCOM.
Long Names:NAME Address of the managed object
ANT<x>CELLNO ant<x>CellNumber
ANT<x>SCNRX ant<x>SecondCellNumberRx
ACONN alarmConnector
FBAND frequencyBand
BCOMTYPE bcomType
System Responses:Operation Completed
After command execution, a message of Changed Configuration Notification is dis-played.
A further message indicates the result of the operation. An example of create command
is the following:
Create BCOM:1
JOB: 6199
PC Time&Date: 31.01.2007 16:31:00 +01:00
NE Time&Date: 31.01.2007 17:30:29 +01:00
USER NAME: NSN
COMMAND: Create BCOM:NAME=RACK:0/BCOM:1,ACONN=ENVA0,FBAND=Gsm900,
ANT0CELLNO=0,ANT0WDRX=FCUMAIN1N1,ANT0WDTX=
FCUMAIN1TX1,ANT1CELLNO=0,ANT1WDRX=FCUMAIN4N,ANT1WDTX=FCUMAIN4TX0,ANT2CELLNO=0,ANT2WDRX=FCUMAIN5N,ANT2WDTX=FCUMAIN5TX0,ANT3CELLNO=0,ANT3WDRX=FCUMAIN3N1,ANT3WDTX=FCUMAIN3TX1,ANT4CELLNO=0,ANT4WDRX=FCUMAIN0N1,ANT4WDTX=FCUMAIN0TX1,ANT5CELLNO=0,ANT5WDRX=FCUMAIN2N1,ANT5WDTX=FCUMAIN2TX1;
DN0933412 Issue 0197
BTSplus mainline commands at the Flexi BSC product family
BCOM
Id:0900d805805b0cb2
SW RELEASE: 01-04-18-06-13-04_07-01-26
COMMAND RESULT: Operation successful
ant0CellNumber = 0
ant1CellNumber = 0
ant2CellNumber = 0
ant3CellNumber = 0
ant4CellNumber = 0
ant5CellNumber = 0
ant0WiringDataRx = FCUMAIN1N1
ant1WiringDataRx = FCUMAIN4N
ant2WiringDataRx = FCUMAIN5N
ant3WiringDataRx = FCUMAIN3N1
ant4WiringDataRx = FCUMAIN0N1
ant5WiringDataRx = FCUMAIN2N1
ant0WiringDataTx = FCUMAIN1TX1
ant1WiringDataTx = FCUMAIN4TX0
ant2WiringDataTx = FCUMAIN5TX0
ant3WiringDataTx = FCUMAIN3TX1
ant4WiringDataTx = FCUMAIN0TX1
ant5WiringDataTx = FCUMAIN2TX1
aconn=ENVA0
frequencyBand = Gsm900
END OF OUTPUT FOR JOB 6199
Command:
6A 00 80 FF 12 02 81 A9 89 25 00 01 46 01 00 47
01 00 48 01 00 49 01 00 4A 01 00 4B 01 00 59 04
02 2A FF 01 5B 04 00 2A FF 04 5D 04 00 2A FF 05
5F 04 02 2A FF 03 61 04 02 2A FF 00 63 04 02 2A
FF 02 5A 04 01 2A FF 01 5C 04 00 2A FF 04 5E 04
00 2A FF 05 60 04 01 2A FF 03 62 04 01 2A FF 00
64 04 01 2A FF 02 70 01 00 71 01 01
Response:
6A 00 80 00 02 12 01 AA 89 25 00 01 46 01 00 47
98DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805b0cb2
BCOM
01 00 48 01 00 49 01 00 4A 01 00 4B 01 00 59 04
02 2A FF 01 5B 04 00 2A FF 04 5D 04 00 2A FF 05
5F 04 02 2A FF 03 61 04 02 2A FF 00 63 04 02 2A
FF 02 5A 04 01 2A FF 01 5C 04 00 2A FF 04 5E 04
00 2A FF 05 60 04 01 2A FF 03 62 04 01 2A FF 00
64 04 01 2A FF 02 70 01 00 71 01 01
Operation Failed
None.
Application Guidelines:
• After the CREATE command, commands SetWiringRx BCOM and SetWiringTx BCOM must be issued to specify antenna combiner wiring
Example of Command Execution:Create BCOM:NAME=RACK:0/BCOM:1, ANT0CELLNO=0, ACONN=ENVA0, FBAND=GSM900;
DELETE BCOM
Command Tree:“MANAGED-ELEMENT h BSS-EQUIPMENT h BTSEP h RACK h BCOM h DELETE BCOM”
Applicability:Phase 2 and Phase 3.
Visibility level: 2.
Command Description:This command is used to delete BCOM.
Long Names:NAME Address of the managed object
System Responses:Operation Completed
After command execution, a message of Changed Configuration Notification is dis-played. A further message indicates the result of the operation. An example of delete command is the following:
Delete BCOM:1
JOB: 6179
DELETE BCOM NAME=RACK:0..7/BCOM:0..1;
DN0933412 Issue 0199
BTSplus mainline commands at the Flexi BSC product family
BCOM
Id:0900d805805b0cb2
PC Time&Date: 31.01.2007 16:25:51 +01:00
NE Time&Date: 31.01.2007 17:25:20 +01:00
USER NAME: NSN
COMMAND: Delete BCOM:NAME=RACK:0/BCOM:1;
SW RELEASE: 01-04-18-06-13-04_07-01-26
COMMAND RESULT: Operation successful
END OF OUTPUT FOR JOB 6179
Command:
0A 00 80 FF 12 02 81 AC 89 25 00 01
Response:
0A 00 80 00 02 12 01 AD 89 25 00 01
Operation Failed
None.
Application Guidelines:None
Example of Command Execution:Delete BCOM:NAME=RACK:0/BCOM:1;
GET BCOM
Command Tree:“MANAGED-ELEMENT h BSS-EQUIPMENT h BTSEP h RACK h BCOM h GET BCOM”
Applicability:Phase 2 and Phase 3.
Visibility level: 0.
Command Description:This command displays the attributes of the BCOM except the wiring data attributes.
GET BCOM NAME=RACK:0..7/BCOM:0..1 [,REQATTL=ALS, AST, AVS, OST, PRS, RELFUNCOBJ, ANT<x>CELLNO, ANT<x>SCNRX, ACONN, FBAND, BCOMTYPE];
100DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805b0cb2
BCOM
Long Names:NAME Address of the managed object
REQATTL Required attribute list
ALS alarmStatus
AST administrativeState
AVS availabilityStatus
OST operationalState
PRS proceduralStatus
RELFUNCOBJ relatedFuncObjects
ANT<x>CELLNO ant<x>CellNumber
ANT<x>SCNRX ant<x>SecondCellNumberRx
ACONN alarmConnector
FBAND frequencyBand
BCOMTYPE bcomType
System Responses:Operation Completed
A further message indicates the result of the operation. An example of get command is
the following:
JOB: 26
PC Time&Date: 12:03:04 03/24/2005
NE Time&Date: 00:02:31 11/29/2004
USER NAME: NSN
COMMAND: Get BCOM:NAME=RACK:0/BCOM:0;
SW RELEASE: 01-04-18-01- 26-51_05-02-23
COMMAND RESULT: Operation successful
alarmStatus = CRITICAL
administrativeState = Unlocked
availabilityStatus = Failed
ant<x>CellNumber = 2
ant<x>SecondCellNumberRx = 2
aconn=ENVA0
frequencyBand = Gsm900
relatedFuncObjects =
operationalState = DISABLED
proceduralStatus = NULL
DN0933412 Issue 01101
BTSplus mainline commands at the Flexi BSC product family
BCOM
Id:0900d805805b0cb2
END OF OUTPUT FOR JOB 26
Operation Failed
The GET command has not been successfully executed. A general NACK will indicate possible errors or a specific NACK strictly related to the single command is possible.
Application Guidelines:None.
Example of Command Execution:BCOM:NAME=RACK:0/BCOM:0,REQATTL=ALS&AST&AVS&ANT<x>CELLNO&ANT <x>SCNRX&OST&PRS&RELFUNCOBJ&ACONN&FBAND;
GETRELATIONSHIP BCOM
Command Tree:“MANAGED-ELEMENT h BSS-EQUIPMENT h BTSEP h RACK h BCOM h GETRELATIONSHIP BCOM”
Applicability:Phase 2 and Phase 3.
Visibility level: 0.
Command Description:This command is used to retrieve the functional relationship information for the selected HMO (Hardwar Managed Object); the relationship information consists of all FMOs (Functional Managed Object) using the HMO service.
Long Names:NAME Address of the managed object
REQATTL Required attribute list
System Responses:Operation Completed
After command execution, a message of Changed configuration Notification is dis-played.
A further message indicates the result of the operation. An example of getrelationship command is the following:
JOB: 1227221
PC Time&Date: 01/29/2007 14:44:27 +01:00
NE Time&Date: 01/29/2007 15:44:11 +01:00
USER NAME: NSN
GETRELATIONSHIP BCOM
NAME=RACK:0..7/BCOM:0..1;
102DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805b0cb2
BCOM
COMMAND: Getrelationship BCOM:NAME=RACK:0/BCOM:0;
SW RELEASE: 01-04-18-06-13-04_07-01-26
COMMAND RESULT: Operation successful
relatedFuncObjects =
FMO = BTS:0/TRX:4
FMO = BTS:0/TRX:6
FMO = BTS:0/TRX:8
FMO = BTS:0/TRX:10
FMO = BTS:0/TRX:9
FMO = BTS:0/TRX:2
END OF OUTPUT FOR JOB 1227221
JOB: 1227222
PC Time&Date: 01/29/2007 14:44:27 +01:00
NE Time&Date: 01/29/2007 15:44:11 +01:00
USER NAME: NSN
COMMAND: Getrelationship BCOM:NAME=RACK:0/BCOM:1;
SW RELEASE: 01-04-18-06-13-04_07-01-26
COMMAND RESULT: Operation successful
relatedFuncObjects =
FMO = BTS:0/TRX:1
FMO = BTS:0/TRX:3
FMO = BTS:0/TRX:5
FMO = BTS:0/TRX:7
FMO = BTS:0/TRX:11
FMO = BTS:0/TRX:0
Operation Failed
None.
Application Guidelines:None.
DN0933412 Issue 01103
BTSplus mainline commands at the Flexi BSC product family
BCOM
Id:0900d805805b0cb2
Example of Command Execution:Getrelationship BCOM:NAME=RACK:0/BCOM:0;
GETTEST BCOM
Command Tree:“MANAGED-ELEMENT h BSS-EQUIPMENT h BTSEP h RACK h BCOM h GETTEST BCOM”
Applicability:Phase 2 and Phase 3.
Visibility level: 0.
Command Description:This command displays the attributes of the BCOM test.
Long Names:NAME Address of the managed object
REQATTL Required attribute list
System Responses:Operation Completed
After command execution, a message of Changed Configuration Notification is dis-played. A further message indicates the result of the operation. An example of gettest command is the following:
JOB: 25
PC Time&Date: 12:01:44 03/24/2005
NE Time&Date: 00:01:11 11/29/2004
USER NAME: NSN
COMMAND: Gettest BCOM:NAME=RACK:0/BCOM:0;
SW RELEASE: 01-04-17-06-26-51_05-02-23
COMMAND RESULT: Operation successful
MOT = RACK:0/BCOM:0
testMonitor =
phaseId = PreliminaryTestsBcom
phaseStatus = Running
phaseId = CheckAlarmStatusBcom
phaseStatus = Waiting
GETTEST BCOM NAME=RACK:0..7/BCOM:0..1;
104DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805b0cb2
BCOM
phaseId = EndTestBcom
phaseStatus = Waiting
testOutcome = INCONCLUSIVE
testState = INITIALIZING
END OF OUTPUT FOR JOB 25
Operation Failed
The GET command has not been successfully executed. A general NACK will indicate possible errors or a specific NACK strictly related to the single command is possible.
Application Guidelines:None.
Example of Command Execution:Gettest BCOM:NAME=RACK:0/BCOM:0,REQATTL=MORT&TESTMON&TESTOUT&
TESTST;
GETWIRINGRX BCOM
Command Tree:“MANAGED-ELEMENT h BSS-EQUIPMENT h BTSEP h RACK h BCOM h GETWIRINGRX BCOM”
Applicability:Phase 2 and Phase 3.
Visibility level: 0.
testMonitor it is a list of all test phases related to the selected object; for each phase the related phaseStatus is provided (Passed, Failed, Running or Waiting).
phaseId =
phaseStatus =
phaseId =
phaseStatus =
...
...
testOutcome It represents the test result: it can be Inconclusive (if the phases already executed were successful) or Fail (if at least one of the executed phases failed).
testState = Testing It can assume one of the following values: not_initialized, idle, initializing, sus-pended, testing, terminating and dis-abled.
GETWIRINGRX BCOM NAME=RACK:0..7/BCOM:0..1 ,REQATTL=ANT<x>WDRX;
DN0933412 Issue 01105
BTSplus mainline commands at the Flexi BSC product family
BCOM
Id:0900d805805b0cb2
Command Description:This command displays the wiring data attributes of the BCOM for RX path.
It is applicable only on: BS240, BS240II, BS240XL, BS240XLII, BS241, BS241 II.
Long Names:NAME Address of the managed object
REQATTL Required attribute list
ANT<x>WDRX ant<x>WiringDataRx
System Responses:Operation Completed
A further message indicates the result of the operation. An example of getWiringRx command is the following:
********** Message 60 **********
JOB: 60
PC Time&Date: 17.12.2007 10:20:51 +01:00
NE Time&Date: 01.01.1990 00:07:40 +00:00
USER NAME: NSN
COMMAND: GetWiringRx
BCOM:NAME=RACK:0/BCOM:0,REQATTL=ANT0WDRX&ANT1WDRX&ANT2WDRX&ANT3WDRX&ANT4WDRX&ANT5WDRX;
SW RELEASE: 01-04-18-01-18-01_07-12-14
COMMAND RESULT:Operation successful
ant0WiringDataRx = CU0N & CU1N & CU2N & CU3N & FCUMAIN5N & FCUMAIN5N1 & FCUMAIN6N & FCUMAIN6N1
ant1WiringDataRx = NULL
ant2WiringDataRx = NULL
ant3WiringDataRx = NULL
ant4WiringDataRx = NULL
ant5WiringDataRx = NULL
END OF OUTPUT FOR JOB 60
Binary Command
12 00 80 ff 12 02 81 b3 ab 25 00 00 1a 06 59 5b 5d 5f 61 63
Binary Response
106DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805b0cb2
BCOM
4a 00 80 00 02 12 01 82 ab 25 00 00 59 20 00 12 ff 00 00 12
ff 01 00 12 ff 02 00 12 ff 03 00 2a ff 05 02 2a ff 05 00 2a
ff 06 02 2a ff 06 5b 04 ff ff ff ff 5d 04 ff ff ff ff 5f 04
ff ff ff ff 61 04 ff ff ff ff 63 04 ff ff ff ff
Operation Failed
The GETWIRINGRX command has not been successfully executed. A general NACK will indicate possible errors or a specific NACK strictly related to the single command is possible.
Application Guidelines:None.
Example of Command Execution:GetWiringRx
BCOM:NAME=RACK:0/BCOM:0,REQATTL=WDRX&ANT;
GETWIRINGTX BCOM
Command Tree:“MANAGED-ELEMENT h BSS-EQUIPMENT h BTSEP h RACK h BCOM h GETWIRINGTX BCOM”
Applicability:Phase 2 and Phase 3.
Visibility level: 0.
Command Description:This command displays the wiring data attributes of the BCOM for TX path.
It is applicable only on: BS240, BS240II, BS240XL, BS240XLII, BS241, BS241 II.
Long Names:NAME Address of the managed object
REQATTL Required attribute list
ANT<x>WDTX ant<x>WiringDataTx
System Responses:Operation Completed
- Operation Completed
A further message indicates the result of the operation. An example of getWiringTx command is the following:
********** Message 61 **********
GETWIRINGTX BCOM NAME=RACK:0..7/BCOM:0..1 ,REQATTL=ANT<x>WDTX;
DN0933412 Issue 01107
BTSplus mainline commands at the Flexi BSC product family
BCOM
Id:0900d805805b0cb2
JOB: 61
PC Time&Date: 17.12.2007 10:20:59 +01:00
NE Time&Date: 01.01.1990 00:07:48 +00:00
USER NAME: NSN
COMMAND: GetWiringTx
BCOM:NAME=RACK:0/BCOM:0,REQATTL=ANT0WDTX&ANT1WDTX&ANT2WDTX
&ANT3WDTX&ANT4WDTX&ANT5WDTX;
SW RELEASE: 01-04-18-01-18-01_07-12-14
COMMAND RESULT:Operation successful
ant0WiringDataTx = CU0 & CU1 & CU2 & CU3
ant1WiringDataTx = NULL
ant2WiringDataTx = NULL
ant3WiringDataTx = NULL
ant4WiringDataTx = NULL
ant5WiringDataTx = NULL
END OF OUTPUT FOR JOB 61
Binary Command
12 00 80 ff 12 02 81 b6 ab 25 00 00 1a 06 5a 5c 5e 60 62 64
Binary Response
3a 00 80 00 02 12 01 82 ab 25 00 00 5a 10 ab 12 ff 00 ab 12
ff 01 ab 12 ff 02 ab 12 ff 03 5c 04 ff ff ff ff 5e 04 ff ff
ff ff 60 04 ff ff ff ff 62 04 ff ff ff ff 64 04 ff ff ff ff
Operation Failed
The GETWIRINGTX command has not been successfully executed. A general NACK will indicate possible errors or a specific NACK strictly related to the single command is possible.
Application Guidelines:None.
Example of Command Execution:GetWiringTx
108DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805b0cb2
BCOM
BCOM:NAME=RACK:0/BCOM:0,REQATTL=WDTX&ANT;
LOCK BCOM
Command Tree:“MANAGED-ELEMENT h BSS-EQUIPMENT h BTSEP h RACK h BCOM h LOCK BCOM”
Applicability:Phase 2 and Phase 3.
Visibility level: 1.
Command Description:This command changes the administrative state of the BCOM.
Long Names:NAME Address of the managed object
System Responses:Operation Completed
The specified change of administrative state has been perfomed:
JOB: 27
PC Time&Date: 12:03:17 03/24/2005
NE Time&Date: 00:02:44 11/29/2004
USER NAME: NSN
COMMAND: Lock BCOM:NAME=RACK:0/BCOM:0;
SW RELEASE: 01-04-17-06-26-51_05-02-23
COMMAND RESULT: Operation successful
administrativeState = Locked
END OF OUTPUT FOR JOB 27
CHANGED STATE EVENT REPORT:
This provides information about the administrative state, the operational state and the availability status every time a state change occurs:
JOB: 28
LOCK BCOM NAME=RACK:0..7/BCOM:0..1;
DN0933412 Issue 01109
BTSplus mainline commands at the Flexi BSC product family
BCOM
Id:0900d805805b0cb2
PC Time&Date: 12:03:17 03/24/2005
NE Time&Date: 00:02:44 11/29/2004
USER NAME: NSN
SW RELEASE: 01-04-17-06-26-51_05-02-23
COMMAND RESULT: Operation successful
CHANGED STATE EVENT REPORT:
NAME = RACK:0/BCOM:0
Administrative State = LOCKED
Notification Identifier = 22
END OF OUTPUT FOR JOB 28
Operation Failed
The specified change of administrative state has not been performed (e.g. the object is redundant and its spare copy is disabled or already locked, a subordinate resource cannot go into disabled state with "dependency" availability status).
Application Guidelines:None.
Example of Command Execution:Lock BCOM:NAME=RACK:0/BCOM:0;
PERFTEST BCOM
Command Tree:“MANAGED-ELEMENT h BSS-EQUIPMENT h BTSEP h RACK h BCOM h PERFTEST BCOM”
Applicability:Phase 2 and Phase 3.
Visibility level: 1.
Command Description:This command is used to start an asynchronous test in BCOM.
Long Names:NAME Address of the managed object
System Responses:Operation Completed
PERFTEST BCOM NAME=RACK:0..7/BCOM:0..1;
110DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805b0cb2
BCOM
Test configuration has been set and the specified test has been started. The System response will not be addressed to the MOT but to the object.
JOB: 30
PC Time&Date: 12:03:25 03/24/2005
NE Time&Date: 00:02:52 11/29/2004
USER NAME: NSN
COMMAND: Perftest BCOM:NAME=RACK:0/BCOM:0;
SW RELEASE: 01-04-17-06-26-51_05-02-23
COMMAND RESULT: Operation successful
MOT = RACK:0/BCOM:0
tO = BTSETEST:1
END OF OUTPUT FOR JOB 30
JOB: 31
PC Time&Date: 12:03:25 03/24/2005
NE Time&Date: 00:02:52 11/29/2004
USER NAME: NSN
SW RELEASE: 01-04-17-06-26-51_05-02-23
COMMAND RESULT: Operation successful
ChangedConfigurationNotification:
name = BTSETEST:1
ChangeInfo = created
END OF OUTPUT FOR JOB 31
JOB: 32
PC Time&Date: 12:03:25 03/24/2005
NE Time&Date: 00:02:52 11/29/2004
DN0933412 Issue 01111
BTSplus mainline commands at the Flexi BSC product family
BCOM
Id:0900d805805b0cb2
USER NAME: NSN
SW RELEASE: 01-04-17-06-26-51_05-02-23
COMMAND RESULT: Operation successful
CHANGED STATE EVENT REPORT:
NAME = RACK:0/BCOM:0
Availability Status = Failed
Notification Identifier = 27
END OF OUTPUT FOR JOB 32
JOB: 33
PC Time&Date: 12:03:25 03/24/2005
NE Time&Date: 00:02:52 11/29/2004
USER NAME: NSN
SW RELEASE: 01-04-17-06-26-51_05-02-23
COMMAND RESULT: Operation successful
Test Report:
name = BTSETEST:1
testOutcome = FAILED
testTermination = Normal
MOT = RACK:0/BCOM:0
executedPhases =
PreliminaryTestsBcom
EndTestBcom
failedPhases =
phaseId = CheckAlarmStatusBcom
additionalWords =
H`0001
H`0000
H`0000
H`0000
H`0000
H`0000
H`0000
112DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805b0cb2
BCOM
H`0000
proposedRepairActions =
#0#
#0#
#0#
#0#
END OF OUTPUT FOR JOB 33
JOB: 34
PC Time&Date: 12:03:25 03/24/2005
NE Time&Date: 00:02:52 11/29/2004
USER NAME: NSN
SW RELEASE: 01-04-17-06-26-51_05-02-23
COMMAND RESULT: Operation successful
ChangedConfigurationNotification:
name = BTSETEST:1
ChangeInfo = deleted
END OF OUTPUT FOR JOB 34
The test results will be displayed at the end of the test phases.
Result TEST:
name = TEST:<n>
testOutcome = This field represents the test result; one of the fol-lowing values can be displayed:
Pass all the test phases are successfully performed.
Inconclusive the test is aborted by the system or the test is terminated by the opera-tor.
Fail if at least one of the executed phases fail.
mOts = It is the identifier of the hardware object under test.
testTermination = It specifies how the test is terminated, it can assume the following values:
DN0933412 Issue 01113
BTSplus mainline commands at the Flexi BSC product family
BCOM
Id:0900d805805b0cb2
Operation Failed
This NACK-message occurs in the following cases: Message cannot be performed, test not supported, capacity restrictions, physical configuration cannot be performed, object not locked.
Application Guidelines:None.
Example of Command Execution:Perftest BCOM:NAME=RACK:0/BCOM:0;
SET BCOM
Command Tree:“MANAGED-ELEMENT h BSS-EQUIPMENT h BTSEP h RACK h BCOM h SET BCOM”
Applicability:Phase 2 and Phase 3.
Visibility level: 2.
Normal all the test phases are performed.
Abort the test is aborted by system.
Cancel the test is terminated by operator.
executedPhases
phaseId = It represents the list of the executed test phases (in case of successful test result, all the test phases will be listed).
additionalWords =
....
failedPhases
phaseId = It represents the list of the failed test phase; addi-tional information is provided for each phase.phaseId =
....
skippedPhases
phaseId = It represents the list of the skipped phases; they are displayed only for test stopped during it execution.phaseId =
....
poprosedRepair Action =
A list of most probable fail probable causes is shown (max four messages)
SET BCOM NAME=RACK:0..7/BCOM:0..1 [,ANT<x>CELLNO=] [,ANT<x>SCNRX=] [,ACONN=] [,FBAND=] [,BCOMTYPE=];
114DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805b0cb2
BCOM
Command Description:This command allows modification of the attributes of the BCOM. For setting of wiring data attributes of BCOM the commands: SetWiringRx BCOM and SetWiringTx BCOM must be used.
Long Names:NAME Address of the managed object
ANT<x>CELLNO ant<x>CellNumber
ANT<x>SCNRX ant<x>SecondCellNumberRx
ACONN alarmConnector
FBAND frequencyBand
BCOMTYPE bcomType
System Responses:Operation Completed
After command execution, a message of Changed Attribute Event Report is displayed. A further message indicates the result of the operation. An example of set command is the following:
JOB: 46
PC Time&Date: 12:07:06 03/24/2005
NE Time&Date: 00:06:33 11/29/2004
USER NAME: NSN
COMMAND: Set BCOM:NAME=RACK:0/BCOM:0;
SW RELEASE: 01-04-17-06-26-51_05-02-23
COMMAND RESULT: Operation successful
END OF OUTPUT FOR JOB 46
Operation Failed
The specified attributes have not been set. In addition to the general NACK causes, a specific NACK cause, which indicates that the command is inconsistent with the physical configuration, is possible.
Application Guidelines:
• The existing state and status attributes shall be assigned to the attributes group STATES
• <x> = 0 .. 5.
• With the SET BCOM command it is possible to 'unset' the parameters setting the value 'NULL', e.g. the cell parameters. To 'unset' the parameters first you must use
DN0933412 Issue 01115
BTSplus mainline commands at the Flexi BSC product family
BCOM
Id:0900d805805b0cb2
BCOM SetWiringTx& Set WiringRx commands, then Set command (to unset cell assignment).
Example:
SetWiringTX BCOM:NAME=RACK:0/BCOM:0, ANT0WDTX=<NULL>,
ANT1WDTX=<NULL>,
ANT2WDTX=<NULL>, ANT3WDTX=<NULL>,
,ANT4WDTX=<NULL>,,ANT5WDTX=<NULL>;
;
SetWiringRX BCOM:NAME=RACK:0/BCOM:0, ANT0WDRX=<NULL>,
ANT1WDRX=<NULL>,
ANT2WDRX=<NULL>, ANT3WDRX=<NULL>,
,ANT4WDRX=<NULL>,,ANT5WDRX=<NULL>;
;
Set BCOM:NAME=RACK:0/BCOM:0,ANT0CELLNO=<NULL>,
ANT0SCNRX=<NULL>,ANT1CELLNO=<NULL>,ANT1SCNRX=<NULL>, ANT2CELLNO=<NULL>,ANT2SCNRX=<NULL>,ANT3CELLNO=<NULL>,
ANT3SCNRX=<NULL>,ANT4CELLNO=<NULL>,ANT4SCNRX=<NULL>,
ANT5CELLNO=<NULL>,ANT5SCNRX=<NULL>;
Example of Command Execution:Set BCOM:NAME=RACK:0/BCOM:0,ant<x>CellNumber=2, ant<x>SecondCellNum-berRx= 2,ACONN=ENVA0,Fband=Gsm900;
SETWIRINGRX BCOM
Command Tree:“MANAGED-ELEMENT h BSS-EQUIPMENT h BTSEP h RACK h BCOM h SETWIRINGRX BCOM”
Applicability:Phase 2 and Phase 3.
Visibility level: 2.
Command Description:This command allows modification of the wiring data attributes of the BCOM for RX path.
This command shall be used after creation of BCOM object. Up to 8 wiring destinations can be set allowing to define also the configuration MDUX + HYBRID6 +COAMCO.
This is valid only for: BS240, BS240II, BS240XL, BS240XLII, BS241, BS241 II.
Long Names:NAME Address of the managed object
SETWIRINGRX BCOM NAME=RACK:0..7/BCOM:0..1 [,ANT<x>WDRX=];
116DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805b0cb2
BCOM
ANT<x>WDRX ant<x>WiringDataRx
System Responses:Operation Completed
After command execution, a message of Changed Attribute Event Report is displayed.
A further message indicates the result of the operation. An example of SetWiringRx command is the following:
JOB: 56
PC Time&Date: 17.12.2007 10:19:03 +01:00
NE Time&Date: 01.01.1990 00:05:52 +00:00
USER NAME: NSN
COMMAND: SetWiringRx
BCOM:NAME=RACK:0/BCOM:0,ANT0WDRX=CU0N&CU1N&CU2N&CU3N&FCUMAIN5N&FCUMAIN5N1&FCUMAIN6N&FCUMAIN6N1;
SW RELEASE: 01-04-18-01-18-01_07-12-14
COMMAND RESULT:Operation successful
ant0WiringDataRx = CU0N & CU1N & CU2N & CU3N & FCUMAIN5N & FCUMAIN5N1& FCUMAIN6N & FCUMAIN6N1
END OF OUTPUT FOR JOB 56
Operation Failed
In addition to the general NACK causes, a specific NACK cause, which indicates that the command is inconsistent with the physical configuration, is possible.
Application Guidelines:
• The 1 attribute for each antenna shall be assigned to 6 separate groups 'ANTENNA <x>'.
• <x> = 0 .. 5.
• With the SETWIRINGRX BCOM command it is possible to 'unset' the parameters setting the value 'NULL', for wiringDataRx attributes and with the SETWIRINGTX BCOM command it is possible to 'unset' the parameters setting the value 'NULL' and finally by using a command "SET BCOM" to 'unset' the cell parameters
Example:
SetWiringRx
BCOM:NAME=RACK:0/BCOM:0,ANT0WDRX=<NULL>,
ANT1WDRX=<NULL>,ANT2WDRX=<NULL>,
DN0933412 Issue 01117
BTSplus mainline commands at the Flexi BSC product family
BCOM
Id:0900d805805b0cb2
ANT3WDRX=<NULL>, ANT4WDRX=<NULL>, ANT5WDRX=<NULL>,
;
SetWiringTx
BCOM:NAME=RACK:0/BCOM:0,ANT0WDTX=<NULL>,
ANT1WDTX=<NULL>,ANT2WDTX=<NULL>,
ANT3WDTX=<NULL>, ANT4WDTX=<NULL>, ANT5WDTX=<NULL>,
Set BCOM:NAME=RACK:0/BCOM:0,ANT0CELLNO=<NULL>,
ANT0SCNRX=<NULL>,ANT1CELLNO=<NULL>,ANT1SCNRX=<NULL>,
ANT2CELLNO=<NULL>,ANT2SCNRX=<NULL>,ANT3CELLNO=<NULL>,
ANT3SCNRX=<NULL>,ANT4CELLNO=<NULL>,ANT4SCNRX=<NULL>,
ANT5CELLNO=<NULL>,ANT5SCNRX=<NULL>;
Example of Command Execution:SetWiringRx BCOM:NAME=RACK:0/BCOM:0,
ANT0WDRX=CU0N&CU1N&CU2N&CU3N&FCUMAIN5N&FCUMAIN5N1&FCUMAIN6N&FCUMAIN6N1;
g The wiring data of cell configurations with MDUX, HYBRID6 and COAMCO are neither completely visible nor configurable via RC, SetWiringRx BCOM command not forseen for RC, when to display the wiring for this configuration always max 2 CUs.TX wiring destinations and max 4 CUs Rx wiring destinations for each corre-sponding BCOM port is displayed even if 4 CUs for TX path and 8 CUs Rx path are wired.
SETWIRINGTX BCOM
Command Tree:“MANAGED-ELEMENT h BSS-EQUIPMENT h BTSEP h RACK h BCOM h SETWIRINGTX BCOM”
Applicability:Phase 2 and Phase 3.
Visibility level: 2.
Command Description:This command allows modification of the wiring data attributes of the BCOM for TX path.
This command shall be used after creation of BCOM object. Up to 4 wiring destinations can be set allowing to define also the configuration MDUX + HYBRID6 +COAMCO.
This is valid only for: BS240, BS240II, BS240XL, BS240XLII, BS241, BS241 II.
SETWIRINGTX BCOM NAME=RACK:0..7/BCOM:0..1 [,ANT<x>WDTX=];
118DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805b0cb2
BCOM
Long Names:NAME Address of the managed object
ANT<x>WDTX ant<x>WiringDataTx
System Responses:Operation Completed
After command execution, a message of Changed Attribute Event Report is displayed.
A further message indicates the result of the operation. An example of SetWiringTx command is the following:
JOB: 53
PC Time&Date: 17.12.2007 10:17:53 +01:00
NE Time&Date: 01.01.1990 00:04:42 +00:00
USER NAME: NSN
COMMAND: SetWiringTx
BCOM:NAME=RACK:0/BCOM:0,ANT0WDTX=CU0&CU1&CU2&CU3;
SW RELEASE: 01-04-18-01-18-01_07-12-14
COMMAND RESULT:Operation successful
ant0WiringDataTx = CU0 & CU1 & CU2 & CU3
END OF OUTPUT FOR JOB 53
Binary Command
1c 00 80 ff 12 02 81 d6 ab 25 00 00 5a 10 ab 12 ff 00 ab 12
ff 01 ab 12 ff 02 ab 12 ff 03
Binary Response
1c 00 80 00 02 12 01 d7 ab 25 00 00 5a 10 ab 12 ff 00 ab 12
ff 01 ab 12 ff 02 ab 12 ff 03
Operation Failed
None.
Application Guidelines:
• The 1 attribute for each antenna shall be assigned to 6 separate groups 'ANTENNA <x>'.
• <x> = 0 .. 5
DN0933412 Issue 01119
BTSplus mainline commands at the Flexi BSC product family
BCOM
Id:0900d805805b0cb2
• With the SETWIRINGTX BCOM command it is possible to 'unset' the parameters setting the value 'NULL', for wiringDataTx attributes and with the SETWIRINGRX BCOM command it is possible to 'unset' the parameters setting the value 'NULL' and finally by using a command "SET BCOM" to 'unset' the cell parameters.
Example:
SetWiringTx
BCOM:NAME=RACK:0/BCOM:0,ANT0WDTX=<NULL>,
ANT1WDTX=<NULL>,ANT2WDTX=<NULL>,
ANT3WDTX=<NULL>, ANT4WDTX=<NULL>, ANT5WDTX=<NULL>,
SetWiringRx
BCOM:NAME=RACK:0/BCOM:0,ANT0WDRX=<NULL>,
ANT1WDRX=<NULL>,ANT2WDRX=<NULL>,
ANT3WDRX=<NULL>, ANT4WDRX=<NULL>, ANT5WDRX=<NULL>,;
Set BCOM:NAME=RACK:0/BCOM:0,ANT0CELLNO=<NULL>,
ANT0SCNRX=<NULL>,ANT1CELLNO=<NULL>,ANT1SCNRX=<NULL>,
ANT2CELLNO=<NULL>,ANT2SCNRX=<NULL>,ANT3CELLNO=<NULL>,
ANT3SCNRX=<NULL>,ANT4CELLNO=<NULL>,ANT4SCNRX=<NULL>,
ANT5CELLNO=<NULL>,ANT5SCNRX=<NULL>;
Example of Command Execution:SetWiringTx BCOM:NAME=RACK:0/BCOM:0,ANT0WDTX=CU0&CU1&CU2&CU3;
g The wiring data of cell configurations with MDUX, HYBRID6 and COAMCO are neither completely visible nor configurable via RC. SetWiringTx BCOM command is not forseen for RC, when the wiring for this configuration is displayed always max 2 CUs.
TX wiring destinations and max 4 CUs Rx wiring destinations for each correspond-ing BCOM port is displayed even if 4 CUs for TX path and 8 CUs Rx path are wired.
STOPTEST BCOM
Command Tree:“MANAGED-ELEMENT h BSS-EQUIPMENT h BTSEP h RACK h BCOM h STOPTEST BCOM”
Applicability:Phase 2 and Phase 3.
Visibility level: 1.
Command Description:This command is used to stop a diagnostic previously started.
STOPTEST BCOM NAME=RACK:0..7/BCOM:0..1;
120DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805b0cb2
BCOM
Long Names:NAME Address of the managed object
System Responses:Operation Completed
Test has been stopped. The System Responses will not be addressed to the MOT but to the object.
Operation Failed
Test has not been stopped. This NACK-message can occur when the specified test is not running or in case of test which cannot be stopped.
Application Guidelines:None.
Example of Command Execution:Stoptest BCOM:NAME=RACK:0/BCOM:0;
UNLOCK BCOM
Command Tree:“MANAGED-ELEMENT h BSS-EQUIPMENT h BTSEP h RACK h BCOM h UNLOCK BCOM”
Result TEST:
name = TEST:<n>
testOutcome = inconclusive
mOts = It is the identifier of the hardware object under test.
testTermination = Cancel
executedPhases
phaseId = It represents the list of the executed test phases; the list is not shown for test in the waiting list (queued)....
.
failedPhases
phaseId = It represents the list of the failed test phase;
additional information is provided for each phase.phaseId =
....
skippedPhases
phaseId = It represents the list of the skipped phases;the list is not shown for test in the waiting list (queued).phaseId =
UNLOCK BCOM NAME=RACK:0..7/BCOM:0..1;
DN0933412 Issue 01121
BTSplus mainline commands at the Flexi BSC product family
BCOM
Id:0900d805805b0cb2
Applicability:Phase 2 and Phase 3.
Visibility level: 1.
Command Description:This command changes the administrative state of the BCOM.
Long Names:NAME Address of the managed object
System Responses:Operation Completed
The specified change of administrative state has been perfomed:
JOB: 36
PC Time&Date: 12:03:45 03/24/2005
NE Time&Date: 00:03:12 11/29/2004
USER NAME: NSN
COMMAND: Unlock BCOM:NAME=RACK:0/BCOM:0;
SW RELEASE: 01-04-17-06-26-51_05-02-23
COMMAND RESULT: Operation successful
administrativeState = Unlocked
END OF OUTPUT FOR JOB 36
CHANGED STATE EVENT REPORT:
This provides information about the administrative state, the operational state and the availability status every time a state change occurs:
JOB: 37
PC Time&Date: 12:03:45 03/24/2005
NE Time&Date: 00:03:12 11/29/2004
USER NAME: NSN
SW RELEASE: 01-04-17-06-26-51_05-02-23
COMMAND RESULT: Operation successful
122DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805b0cb2
BCOM
CHANGED STATE EVENT REPORT:
NAME = RACK:0/BCOM:0
Administrative State = UNLOCKED
Notification Identifier = 29
END OF OUTPUT FOR JOB 37
Operation Failed
The specified change of administrative state has not been performed.
Application Guidelines:None.
Example of Command Execution:Unlock BCOM:NAME=RACK:0/BCOM:0;
DN0933412 Issue 01123
BTSplus mainline commands at the Flexi BSC product family
BPORT
Id:0900d805805b0cb6
BPORTThe object BPORT identifies one of the 2 PCM30/24 interfaces on the COBA and one of the 6 PCM30/24 interfaces on the COSA. The object BPORT holds the configuration data of one Abis port.
CREATE BPORT
Command Tree:“MANAGED-ELEMENT h BSS-EQUIPMENT h BTSEP h BPORT h CREATE BPORT”
Applicability:Phase 2 and Phase 3.
Visibility level: 2.
Command Description:This command is used for the Handling of PCM-Line Configuration and adds the BPORT (BTSE Port) together with its attributes to the BTSE data base. The object BPORT holds the configuration data of one Abis port. The instance number of this object is related to the physical Abis port number (e.g.: Instance 0 is related to the physical port 1 (OVPT), which allows the connection of the BTSE to the Abis line1 and so on).
Long Names:NAME Address of the managed object
BERT bitErrorRateThreshold
L1CTRLTS layer1ControlTs
L1PT layer1ProtocolType
L1RAT layer1RemoteAlarmType
LCONF lineConfiguration
LIMP lineImpedance
System Responses:Operation Completed
After command execution, a message of Changed Configuration Notification is dis-played. A further message indicates the result of the operation. An example of create command is the following:
JOB: 42
PC Time&Date: 11:55:28 03/23/2005
NE Time&Date: 12:57:03 09/15/2004
CREATE BPORT NAME=BPORT:0..7 [,BERT=] [,L1CTRLTS=] ,L1PT= [,L1RAT=] ,LCONF= [,LIMP=];
124DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805b0cb6
BPORT
USER NAME: SAG
SW RELEASE: 01-04-17-01-26-51_05-02-23 COMMAND RESULT: Operation suc-cessful
ChangedConfigurationNotification:
name = BPORT:1
ChangeInfo = created
END OF OUTPUT FOR JOB 42
JOB: 43
PC Time&Date: 11:55:28 03/23/2005
NE Time&Date: 12:57:03 09/15/2004
USER NAME: SAG
COMMAND: Create BPORT:NAME=BPORT:1,L1PT=pcm30crc4,LCONF=star;
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: Operation successful
layer1ProtocolType = pcm30crc4
lineConfiguration = star
END OF OUTPUT FOR JOB 43
Operation Failed
The specified Object has not been created. In addition to the general NACK causes, a specific NACK cause, which indicates that the command is inconsistent with the physical configuration, is possible. An example is the following:
JOB: 44
PC Time&Date: 11:55:52 03/23/2005
NE Time&Date: 12:57:27 09/15/2004
USER NAME: SAG
COMMAND: Create BPORT:NAME=BPORT:2,L1PT=pcm30crc4,LCONF=star;
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: OPERATION FAILED
DN0933412 Issue 01125
BTSplus mainline commands at the Flexi BSC product family
BPORT
Id:0900d805805b0cb6
MO already created (-159)
END OF OUTPUT FOR JOB 44
Application Guidelines:
• Wildcard addressing is not possible
• To guarantee a correct transition of SW releases the operator must use BPort instance 0 for O&M link
• Changing or setting of layer1ProtocolType or layer1RemoteAlarm attributes means a temporary loss of service for the whole BTSE
• Layer1ControlTS must be different to the related BTSM-O&M signalling link
• Layer1ControlTS (if activated) must not be used for other purposes (e.g. signalling, traffic or cross connection and vice versa)
• SpecialBitRobbing attribute is allowed only for PCM24 and means that a special bit (bit 2) is used for signalling of a remote alarm
• BPORTs (0&1, 2&3, 4&5, 6&7) form port pairs which are short-circuited during BTSE coming up
• Bport-0 is clock master for BTSE, all other Bports are slaves. Therefore, PCM line connected to Bport-0 must arrive from different network entity
• To configure a line circuit (e.g.: multidrop, loop) 2 BPort objects have to be created by the operator. As long the 2 objects are not available all BTSEs located behind on this circuit are not reachable. Line alarms detected by one Abis port are mapped to the associated BPort instance
• One star circuit (only one port is involved) is allowed per port pair and must be placed on the lower port number
• Creation of the second port on a port pair (in case of a multidrop/loop circuit) must lead always to the same settings of the attributes as the first port has with the follow-ing exceptions
1) Activation of a layer1ControlTimeslot is only allowed for the first port in case of a multidrop circuit
2) Attribute bitErrorRateThresholds can be set independently
• If COBA2P8 is installed and COSA is disabled/not Installed, the BPORT:2-7 are in Enable.null state but they cannot be used because the HW does not support them.
If COBA4P12 is installed and COSA is disabled/not Installed, the BPORT:2,3 are in Enable.degraded state and the BPORT:4-7 are in Enable.null but they cannot be used because the HW does not support them.
g This is valid for all BTSplus mainline except for the BR BS82II.
Example of Command Execution:Create BPORT:NAME=BPORT:0,L1PT=pcm30crc4,LCONF=star,
BERT=E10_3-E10_3,L1CTRLTS=0-0,L1RAT=ProtocolSignalling,
LIMP=Imp100or120Ohm;
126DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805b0cb6
BPORT
DELETE BPORT
Command Tree:“MANAGED-ELEMENT h BSS-EQUIPMENT h BTSEP h BPORT h DELETE BPORT”
Applicability:Phase 2 and Phase 3.
Visibility level: 2.
Command Description:This command deletes the BPORT (BTSE port) from the BTSE data base.
Long Names:NAME Address of the managed object
System Responses:Operation Completed
After command execution, a message of Changed Configuration Notification is dis-played. A further message indicates the result of the operation. An example of delete command is the following:
JOB: 45
PC Time&Date: 11:55:52 03/23/2005
NE Time&Date: 12:57:27 09/15/2004
USER NAME: SAG
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: Operation successful
ChangedConfigurationNotification:
NAME=BPORT:2
ChangeInfo = deleted
END OF OUTPUT FOR JOB 45
JOB: 46
PC Time&Date: 11:55:56 03/23/2005
NE Time&Date: 12:57:31 09/15/2004
DELETE BPORT NAME=BPORT:0..7;
DN0933412 Issue 01127
BTSplus mainline commands at the Flexi BSC product family
BPORT
Id:0900d805805b0cb6
USER NAME: SAG
COMMAND: Delete BPORT:NAME=BPORT:0;
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: Operation successful
END OF OUTPUT FOR JOB 46
Operation Failed
The specified Object has not been deleted. Additionally to the general NACK causes, a specific NACK cause, meaning that the command is inconsistent with physical configu-ration, is possible.
Application Guidelines:
• Before Deletion of a BPort instance in phase 3, the object must be locked before
• Deletion in phase 3 is allowed only if no TSL is assigned to BPort (XCONNECT defined)
• The BPORT 0 is one of the "Minimal Parameters" of the BTSE. If the BPORT 0 is deleted, the entire BTSE is out of service (only Phase 2)
• BPORT 0 cannot be deleted in Phase 3
Example of Command Execution:Delete BPORT:NAME=BPORT:0;
GET BPORT
Command Tree:“MANAGED-ELEMENT h BSS-EQUIPMENT h BTSEP h BPORT h GET BPORT”
Applicability:Phase 2 and Phase 3.
Visibility level: 0.
Command Description:This command displays the attributes of the PCM lines connected to the COBA (Core Basis).
Long Names:NAME Address of the managed object
REQATTL Required attribute list
ALS alarmStatus
AST administrativeState
GET BPORT NAME=BPORT:0..7 [,REQATTL=ALS, AST, AVS, BERT, L1CTRLTS, L1PT, L1RAT, LCONF, LSIND, LIMP, OST, PRDIRECT, PRS, RELFUNCOBJ];
128DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805b0cb6
BPORT
AVS availabilityStatus
BERT bitErrorRateThreshold
L1CTRLTS layer1ControlTs
L1PT layer1ProtocolType
L1RAT layer1RemoteAlarmType
LCONF lineConfiguration
LSIND lineStatusIndication
LIMP lineImpedance
OST operationalState
PRDIRECT preferredDirection
PRS proceduralStatus
RELFUNCOBJ relatedFuncObjects
System Responses:Operation Completed
After command execution, a message of Changed Configuration Notification is dis-played. A further message indicates the result of the operation. An example of get command is the following:
JOB: 5
PC Time&Date: 11:31:23 03/23/2005
NE Time&Date: 11:29:14 09/15/2004
USER NAME: SAG
COMMAND: GET BPORT:NAME=BPORT:0;
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: Operation successful
alarmStatus = CLEARED
administrativeState = Unlocked
availabilityStatus = NULL
bitErrorRateThreshold =
lowerThreshold = E10_5
upperThreshold = E10_3
layer1ControlTs =
TSL = 0
SSL = 0
layer1ProtocolType = pcm30crc4
layer1RemoteAlarmType = ProtocolSignalling
DN0933412 Issue 01129
BTSplus mainline commands at the Flexi BSC product family
BPORT
Id:0900d805805b0cb6
lineConfiguration = multidrop
lineStatusIndication =
remoteAlarmInd = FALSE
frameSynchronizationLoss = FALSE
CRCFailure = FALSE
noLevel = FALSE
CRCRemoteEnviroment = FALSE
BERTLowerThreshold = FALSE
BERTUpperThreshold = FALSE
promptMaintenanceAlarmInd = FALSE
lineImpedance = accDIP
operationalState = ENABLED
proceduralStatus = NULL
preferredDirection = Null
relatedFuncObjects =
END OF OUTPUT FOR JOB 5
Operation Failed
The GET command has not been successfully executed. A general NACK will indicate possible errors or a specific NACK strictly related to the single command is possible.
Application Guidelines:
• None.
Example of Command Execution:Get BPORT:NAME=BPORT:0,REQATTL=ALS&AST&AVS&BERT&
L1CTRLTS&L1RAT&L1PT&LCONF&LIMP&LSIND&OST&PRDIRECT&PRS&
RELFUNCOBJ;
LOCK BPORT
Command Tree:“MANAGED-ELEMENT h BSS-EQUIPMENT h BTSEP h BPORT h LOCK BPORT”
Applicability:Phase 2 and Phase 3.
Visibility level: 1.
Command Description:This command changes the administrative state of the BPORT object.
LOCK BPORT NAME=BPORT:0..7;
130DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805b0cb6
BPORT
Long Names:NAME Address of the managed object
System Responses:Operation Completed
The specified change of administrative state has been perfomed:
JOB: 47
PC Time&Date: 11:56:00 03/23/2005
NE Time&Date: 12:57:35 09/15/2004
USER NAME: SAG
COMMAND: Lock BPORT:NAME=BPORT:0;
SW RELEASE: 01-04-17-01-26-51_05-02-23 COMMAND RESULT: Operation suc-cessful
administrativeState = LOCKED
END OF OUTPUT FOR JOB 47
CHANGED STATE EVENT REPORT:
This provides information about the administrative state, the operational state and the availability status every time a state change occurs:
JOB: 48
PC Time&Date: 11:56:22 03/23/2005
NE Time&Date: 12:57:57 09/15/2004
USER NAME: SAG
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: Operation successful
CHANGED STATE EVENT REPORT:
NAME=BPORT:0;
Administrative State = LOCKED
Notification Identifier = 143452
DN0933412 Issue 01131
BTSplus mainline commands at the Flexi BSC product family
BPORT
Id:0900d805805b0cb6
END OF OUTPUT FOR JOB 48
Operation Failed
The specified change of administrative state has not been performed (e.g. the object is redundant and its spare copy is disabled or already locked, a subordinate resource cannot go into disabled state with "dependency" availability status).
Application Guidelines:
• BPORT 0 cannot be locked in Phase 3
Example of Command Execution:Lock BPORT:NAME=BPORT:0;
SET BPORT
Command Tree:“MANAGED-ELEMENT h BSS-EQUIPMENT h BTSEP h BPORT h SET BPORT”
Applicability:Phase 2 and Phase 3.
Visibility level: 2.
Command Description:This command permits modification of the attributes of the BPORT (BTES port), previ-ously created with the (create) CREATE BPORT command. The object BPORT holds the configuration data of one Abis port.
Long Names:NAME Address of the managed object
BERT bitErrorRateThreshold
L1CTRLTS layer1ControlTs
L1RAT layer1RemoteAlarmType
LCONF lineConfiguration
LIMP lineImpedance
System Responses:Operation Completed
The specified attribute has been set. In addition, a Changed Attribute Event Report indi-cates that the command has been successfully executed:
JOB: 15
SET BPORT NAME=BPORT:0..7 [,BERT=] [,L1CTRLTS=] [,L1RAT=] [,LCONF=] [,LIMP=];
132DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805b0cb6
BPORT
PC Time&Date: 11:32:16 03/23/2005
NE Time&Date: 11:30:07 09/15/2004
USER NAME: SAG
COMMAND: Set BPORT:NAME=BPORT:0,BERT=E10_5-E10_3;
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: Operation successful
bitErrorRateThreshold =
lowerThreshold = E10_5
upperThreshold = E10_3
END OF OUTPUT FOR JOB 15
Operation Failed
The specified attributes have not been set. In addition to the general NACK causes, a specific NACK cause, which indicates that the command is inconsistent with physical configuration, is possible.
Application Guidelines:
• The layer1ControlTS attribute is applicable only for the line configuration "Loop"
• Changing or setting of layer1RemoteAlarmType attribute means a temporary loss of service for the whole BTSE
• Layer1ControlTS must be different to the related BTSM-O&M signalling link
• SpecialBitRobbing attribute is allowed only for PCM24 and means that a special bit (bit 2) is used for signalling of a remote alarm
Example of Command Execution:Set BPORT:NAME=BPORT:0,BERT=E10_3-E10_3,L1CTRLTS=0-0,
L1RAT=ProtocolSignalling,LCONF=star,LIMP=Imp100or120Ohm;
UNLOCK BPORT
Command Tree:“MANAGED-ELEMENT h BSS-EQUIPMENT h BTSEP h BPORT h UNLOCK BPORT”
Applicability:Phase 2 and Phase 3.
Visibility level: 1.
UNLOCK BPORT NAME=BPORT:0..7;
DN0933412 Issue 01133
BTSplus mainline commands at the Flexi BSC product family
BPORT
Id:0900d805805b0cb6
Command Description:This command changes the administrative state of the BPORT (BTSE port).
Long Names:NAME Address of the managed object
System Responses:Operation Completed
The specified change of administrative state has been perfomed:
JOB: 185
PC Time&Date: 12:06:51 03/23/2005
NE Time&Date: 13:08:26 09/15/2004
USER NAME: SAG
COMMAND: UNLOCK BPORT:NAME=BPORT:0;
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: Operation successful
administrativeState = UNLOCKED
END OF OUTPUT FOR JOB 185
CHANGED STATE EVENT REPORT:
This provides information about the administrative state, the operational state and the availability status every time a state change occurs:
JOB: 186
PC Time&Date: 12:06:51 03/23/2005
NE Time&Date: 13:08:26 09/15/2004
USER NAME: SAG
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: Operation successful
CHANGED STATE EVENT REPORT:
NAME=BPORT:0;
134DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805b0cb6
BPORT
Administrative State = UNLOCKED
Notification Identifier = 135872
END OF OUTPUT FOR JOB 186
Operation Failed
The specified change of administrative state has not been performed.
Application Guidelines:None
Example of Command Execution:Unlock BPORT:NAME=BPORT:0;.
DN0933412 Issue 01135
BTSplus mainline commands at the Flexi BSC product family
BTS
Id:0900d805805b0cb8
BTSThe BTS object locates a cell connected to the related Flexi BSC product family. Logi-cally it represents all the informa-tion related to the cell and to its configuration.
GET BTS
Command Tree:“MANAGED-ELEMENT h BSS-FUNCTIONAL h BTSM h BTS h GET BTS”
Applicability:Phase 3.
Visibility level: 0.
Command Description:This command displays the cell-specific global attributes of a chosen BTS.
Long Names:NAME Address of the managed object
REQATTL Required attribute list
ACBQPFF acBQPFgtFac
ACBQPMAX acBQPMax(%)
ACEFLFF acEFLFgtFac
ACFERMAX acFERMax(%)
ACLNKTYP acLinkType
ACMINEFLDMA acMinEFLDMA(%)
ACMAXEFLDMA acMaxEFLDMA(%)
ACPER acPeriod
GET BTS NAME=BTS:0..11 [,REQATTL=ACBQPFF, ACBQPMAX, ACEFLFF, ACFERMAX, ACLNKTYP, ACMINEFLDMA, ACMAXEFLDMA, ACPER, AMRLKAT, AMRLKATWFS, ANTHOPMOD, ANTHOPP, ANTHOPST, ARFACCHAC-MDF, ASCICIPH, AST, AVS, BCCHFREQ, BSIC, BTSISHOP, BURNOFFS, SYSID, CELLTYPE, CUCONF, DTMHOMTIMER, EAC, EANTHOP, EEOTD, EEXCDIST, ERFACCHALPDMF, ERFACCHCMDF, ERSACCHDL, ERSACCHUL, ETOP, ETXDIVTS, EXCDIST, FACCHQ, FACHBT, FRANOFFS, GSMTIME, HOPMODE, INTAVE-PAR, INTCLASS, INTLVBND, MSTXPMAX, MSTXPMAXC, NEPTTREP, NTWTYPE, NY1, NY2, OST, PCCCHLDI, PNOFACCH, PWROUT, RACHBT, RACHLAS, RELEQUI-POBJ, REPTYP, RFRSINDP, RSACCHRXLDL, RSAC-CHRXLUL, RSACCHTODL, RSACCHTOUL, RXSIGLEVADJ, RXSIGLEVADJC, RXSWCURSET, SEG-MENTID, SWBCAPABILITY, SWBSERVSTATE, T3105, T3151, TCCCHLDI, BTSOBJID, RADIUSEXT, SRADIU-SEXT, MSDISTBEHAV];
136DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805b0cb8
BTS
AMRLKAT aMRLinkAdapTuning
AMRLKATWFS aMRLinkAdapTuningWFS(dB)
ANTHOPMOD antennaHoppingMode
ANTHOPP antennaHoppingPeriod
ANTHOPST antennaHoppingStatus
ARFACCHACMDF applyRFacchOnAnyCmdFrame
ASCICIPH enableCiphForASCI
AST administrativeState
AVS availabilityStatus
BCCHFREQ bcchFrequency
BSIC bsIdentityCode
BTSISHOP btsIsHopping
BURNOFFS burstNumberOffset
SYSID cellAllocationNumber
CELLTYPE cellType
CUCONF carrierUnitConfiguration
DTMHOMTIMER hoDTMTimer(SACCH_multiframe_480/470ms)
EAC enableAc
EANTHOP enableAntennaHopping
EEOTD enableEOTD
EEXCDIST enableExcessiveDistance
ERFACCHALPDMF enableRFacchOnAnyLapdmFrame
ERFACCHCMDF enableRFacchOnCmdFrames
ERSACCHDL enableRSacchDL
ERSACCHUL enableRSacchUL
ETOP enableTOP
ETXDIVTS enableTxDivTimeShift
EXCDIST excessiveDistance(km)
FACCHQ facchQual
FACHBT fachBusyThreshold(dBm)
FRANOFFS frameNumberOffset
GSMTIME gsmTime
HOPMODE hoppingMode
INTAVEPAR intaveParameter
INTCLASS enableInterferenceClass
INTLVBND interferenceLevelBoundaries
MSTXPMAX mSTxPwrMax(*dBm mapped)
MSTXPMAXC mSTxPwrMaxCompl
NEPTTREP notDataRepCount
DN0933412 Issue 01137
BTSplus mainline commands at the Flexi BSC product family
BTS
Id:0900d805805b0cb8
NTWTYPE networkType
NY1 ny1
NY2 ny2
OST operationalState
PCCCHLDI periodCcchLoadIndication(sec)
PNOFACCH periodNotificationFACCH(sec)
PWROUT powerOutputThresholds
RACHBT rachBusyThreshold(dBm)
RACHLAS rachLoadAveragingSlots
RELEQUIPOBJ relatedEquipObjects
REPTYP reportType
RFRSINDP rfResourceIndicationPeriod
RSACCHRXLDL repSacchRxLevDL
RSACCHRXLUL repSacchRxLevUL
RSACCHTODL repSacchTimeOutDL
RSACCHTOUL repSacchTimeOutUL
RXSIGLEVADJ rxSigLevAdjust
RXSIGLEVADJC rxSigLevAdjustCompl
RXSWCURSET rxSwitchCurrentSetting
SEGMENTID segmentId
SWBCAPABILITY switchedBeamCapability
SWBSERVSTATE switchedBeamServState
T3105 btsTimer3105(*10ms)
T3151 uplBusyRepRate
TCCCHLDI thresholdCcchLoadIndication
BTSOBJID btsObjectId
RADIUSEXT radiusExtension(km)
SRADIUSEXT superRadiusExtension(km)
MSDISTBEHAV msDistanceBehaviour
System Responses:Operation Completed
After command execution, a message of Changed Configuration Notification is dis-played. A further message indicates the result of the operation. An example of get command is the following:
JOB: 19
PC Time&Date: 11:33:29 03/23/2005
NE Time&Date: 11:31:19 09/15/2004
138DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805b0cb8
BTS
USER NAME: SAG
COMMAND: Get BTS:NAME=BTS:0;
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: Operation successful
acBQPFgtFac = 0.2
acBQPMax(%) = 5
acEFLFgtFac = 0.04
acFERMax(%) = 5.0
acLinkType = UL_SAMPLES_ONLY
acMaxEFLDMA(%) = per_50
acMinEFLDMA(%) = per_10
acPeriod = SACCH_120
administrativeState = Unlocked
aMRLinkAdapTuning = 100
antennaHoppingMode = NOBCCHTRX
antennaHoppingPeriod = SECOND
antennaHoppingStatus = FALSE
availabilityStatus = NULL
bcchFrequency = 5
bsIdentityCode =
BCC = 3
NCC = 5
btsIsHopping = FALSE
btsTimer3105(*10ms) = 4
burstNumberOffset = 0
cellAllocationNumber = BB900
cellType = STDCELL
enableAc = FALSE
enableAntennaHopping = FALSE
enableEOTD = FALSE
enableExcessiveDistance = TRUE
enableInterferenceClass = TRUE
enableTxDivTimeShift = FALSE
excessiveDistance(km) = 35
facchQual = 5
frameNumberOffset = 0
gsmTime = 30303
DN0933412 Issue 01139
BTSplus mainline commands at the Flexi BSC product family
BTS
Id:0900d805805b0cb8
hoppingMode = BBHOP
intaveParameter = 31
JOB: 19
interferenceLevelBoundaries =
intThrBou1 = 2
intThsBou2 = 6
intThsBou3 = 12
intThsBou4 = 22
intThsBou5 = 63
mSTxPwrMax(*dBm_mapped) = 5
mSTxPwrMaxCompl = 5
mobileCountryCode =
MCC = "555"
networkType = GSMDCS
ny1 = 50
ny2 = 20
operationalState = ENABLED
periodCcchLoadIndication(sec) = 255
periodNotificationFACCH(sec) = 2.5
powerOutputThresholds =
oPwrFaultThreshold = m10db
redOutPwrThreshold = m6db
excesOutPwrThresh = db5
rachBusyThreshold(dBm) = 109
rachLoadAveragingSlots = 204
relatedEquipObjects =
rfResourceIndicationPeriod = 60
rxSwitchCurrentSetting = NULL
startingTime = 65535
switchedBeamCapability = none
switchedBeamServState = NULL
t200 =
sdcchSAPIO = 44
facchTCHF = 31
facchTCHH = 41
saccchTCHSAPIO = 90
sacchSDCCH = 90
sdcchSAPI3 = 90
140DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805b0cb8
BTS
sacchTCHSAPI3 = 135
t3115(*10ms) = 4
taAdjust(microseconds) = 0.0
timerUplinkReply = 20
thresholdCcchLoadIndication = 100
tNCH(*multiframes) = 16
tSync(*10ms) = 1000
tSyncD(*10ms) = 1000
tSyncR(*10ms) = 400
tSyncU(*10ms) = 1000
JOB: 19
tTrau(*10ms) = 1000
txDivTimeShiftExcept = NONE
txDivTimeShiftParam = [-1.00]
voiceGroupUplinkFree(*10ms) = 2
END OF OUTPUT FOR JOB 19
Operation Failed
The GET command has not been successfully executed. A general NACK will indicate possible errors or a specific NACK strictly related to the single command is possible.
Application Guidelines:
• The attribute HOPMODE (hoppingMode) can be set only if there are no subordinate frequency hopping system equipped
• When the attribute INTCLASS is enabled "RF resource indication" messages (rele-vant to the attributes INTAVEPAR, INTLVBND and RFRSINDP) are sent to the Flexi BSC product family
• Values indicating more than 35 Km in the attribute EXCDIST are valid only for extended cells
• The attributes ETXDIVTS, TXDIVTSEXCPT and TXDIVTSPAR have only function-ality for hh=04-01 and hh=04-06
Example of Command Execution:Get BTS:NAME=BTS:0,REQATTL=ACBQPFF&ACBQPMAX&ACEFLFF& ACFER-MAX&ACLNKTYP&ACMAXEFLDMA&ACMINEFLDMAX&ACPER& AMRLKAT& NTHOPMOD&ANTHOPP&ANTHOPST ASCICIPH &AST& AVS&BCCHFREQ&BSIC& BTSISHOP&BURNOFFS&CELLGLID&CELLTYPE&CUCONF&EAC&EANTHOP& EEXCDIST&EEQTD &ERFACCH&ETOP&ETXDI-VTS&EXCDIST&FACCHQ&FILETYPE& FRANOFFS&GSMTIME& HOP-MODE&INTAVEPAR&INTCLASS&INTLVBND&LAPDOVLTRXL&MCC&MSTXPMAX&
DN0933412 Issue 01141
BTSplus mainline commands at the Flexi BSC product family
BTS
Id:0900d805805b0cb8
MSTXPMAXC&NTWTYPE&NY1&NY2&OST&PCCCHLDI&PNOFACCH& PWROUT& RACHBT&RACHLAS&REPTYP&RFACCHFT&RFRSINDP&RXSWCSET&RELEQUIPOBJ&RXSIGLEVADJ&Â RXSIGLEVADJC&RXSWCURSET& STATIME&STDBYST& SWBCAPABILITY&SWBSERVSTATE&Â SWBEAMCPBL&SWBEAMSSTAT&SYSID&T200&T3105&T3115& TAADJ&TCCCHLDI&TNCH& TSYNC&TSYNCD&TSYN-CDL&TSYNCR&TSYNCU&TTRAU& TUPLREP&TXDIVTSEXCPT&TXDI-VTSPAR&TXSIGLEVADJ&TXSIGLEVADJC& VGRULF&VGSCULF
GET BTS TIMER
Command Tree:“MANAGED-ELEMENT h BSS-FUNCTIONAL h BTSM h BTS h GET BTS TIMER”
Applicability:Phase 3.
Visibility level: 0.
Command Description:This command displays the attributes of the BTS timer.
Long Names:NAME Address of the managed object
REQATTL Required attribute list
STATIME startingTime
T200 t200
T3115 t3115(*10ms)
TAADJ taAdjust(microseconds)
TNCH tNCH(*multiframes)
TSYNC tSync(*10ms)
TSYNCD tSyncD(*10ms)
TSYNCR tSyncR(*10ms)
TSYNCU tSyncU(*10ms)
TTRAU tTrau(*10ms)
TUPLREP timerUplinkReply
TXDIVTSPAR txDivTimeShiftParam
TXDIVTSEXCPT txDivTimeShiftExcept
TXSIGLEVADJ txSigLevAdjust
TXSIGLEVADJC txSigLevAdjustCompl
VGSCULFT voiceGroupUplinkFree(*10ms)
GET BTS TIMER NAME=BTS:0..11 ,REQATTL=STATIME, T200, T3115, TAADJ, TNCH, TSYNC, TSYNCD, TSYNCR, TSYNCU, TTRAU, TUPLREP, TXDIVTSPAR, TXDIVTSEXCPT, TXSI-GLEVADJ, TXSIGLEVADJC, VGSCULFT;
142DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805b0cb8
BTS
System Responses:Operation Completed
None
Operation Failed
None
Application Guidelines:None
Example of Command Execution:None
DN0933412 Issue 01143
BTSplus mainline commands at the Flexi BSC product family
BTSEP
Id:0900d805805b0cba
BTSEPThe BTSEP object models the BTSplus mainline family. Following BTSplus mainline tyoes are supported:
• The BS240/1 consists of a base rack with up to 8 TRXs. Optionally it can be con-nected to two extension racks to reach up to 24 TRX
• The BS240XL consists of a base rack with up to 12 TRXs. Optionally it can be con-nected an extension rack to reach up to 24 TRXs
• The BS40/1 and BS40II consists of a base rack with up to 4 TRXs • The BS82II consists of a base rack with up to 2 TRXs. Optionally it can be connected
up two extension rack to reach up to 6 TRXs
g The BTSEP object models also the BTSplus basic. The description of commands related to BTSplus basic is out of the scope of this manual.
DELETE BTSEP DBFILE
Command Tree:“MANAGED-ELEMENT h BSS-EQUIPMENT h BTSEP h DELETE BTSEP DBFILE”
Applicability:Phase 2.
Visibility level: 2.
Command Description:This command deletes the data base file.
Long Names:NAME Address of the managed object
System Responses:Operation Completed
The data base file has been deleted.
JOB: 55
PC Time&Date: 11:56:59 03/23/2005
NE Time&Date: 12:58:13 09/15/2004
USER NAME: NSN
COMMAND: Delete BTSEP DBFILE:NAME=BTSEP:0;
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: Operation successful
DELETE BTSEP DBFILE
NAME=BTSEP:0..0;
144DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805b0cba
BTSEP
END OF OUTPUT FOR JOB 55
Operation Failed
The data base file has not been deleted.
Application Guidelines:
• The file related to REMINV isn't affected by the command
• The command cause a restart of the BTSE and that the operator has to do a new login afterward
• All HW Objects, which were created per command, will be deleted, including "Minimal Configuration"
• All stored SW Loads will still be available
• Only the db of COBA:0 will be deleted
Example of Command Execution:Delete BTSEP DBFILE:NAME=BTSEP:0;
FORMAT BTSEP FLASH
Command Tree:“MANAGED-ELEMENT h BSS-EQUIPMENT h BTSEP h FORMAT BTSEP FLASH”
Applicability:Phase 1 and Phase 2.
Visibility level: 3.
Dangerous
Command Description:This command formats the Flash EPROMs of COBA (Core module). Since it is consid-ered a "dangerous" command, a confirmation dialog will ask you to confirm or cancel the action.
Long Names:NAME Address of the managed object
System Responses:Operation Completed
The Flash EPROMs of the COBA have been formatted.
JOB: 56
FORMAT BTSEP FLASH
NAME=BTSEP:0..0;
DN0933412 Issue 01145
BTSplus mainline commands at the Flexi BSC product family
BTSEP
Id:0900d805805b0cba
PC Time&Date: 11:57:07 03/23/2005
NE Time&Date: 12:58:42 09/15/2004
USER NAME: NSN
COMMAND: Format BTSEP FLASH:NAME=BTSEP:0;
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: Operation successful
END OF OUTPUT FOR JOB 56
Operation Failed
The Flash EPROMs of the COBA have not been formatted.
Application Guidelines:
• The command cause a restart of the BTSE and that the operator has to do a new login afterward
• All HW Objects and all SW Loads will be deleted, complete formatting in COBA:0 if COBA:1 is Power Off
Example of Command Execution:Format BTSEP FLASH:NAME=BTSEP:0;
GET BTSEP NOSWL
Command Tree:“MANAGED-ELEMENT h BSS-EQUIPMENT h BTSEP h GET BTSEP NOSWL”
Applicability:Phase 2 and Phase 3.
Visibility level: 0.
Command Description:This command displays the attributes related to the BTSE (BTS Site Equipment).
Long Names:NAME Address of the managed object
REQATTL Required attribute list
ALIGCOBA alignedCoba
ALRMSEVXXX alarmSeverityXXX
GET BTSEP NOSWL NAME=BTSEP:0..0 [,REQATTL=ALIGCOBA, ALRM-SEVXXX, ALS, AST, AVS, CHIDT, EAUTOREC, EQUPOS, GTWADRV4, LMTLSESS, LMTLTIME, LMTUAL, LMTU-NAME, LOCNAME, OST, OVPTINS, PRS, RELFUNCOBJ, RXDIVSV, SALUNAME, SCLPRIOLST, VENDNA];
146DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805b0cba
BTSEP
ALS alarmStatus
AST administrativeState
AVS availabilityStatus
CHIDT changeOnIDT
EAUTOREC enableAutoRecovery
EQUPOS equipmentPosition
GTWADRV4 gatewayAddressIPv4
LMTLSESS lmtLogonSession
LMTLTIME lmtLogonTime
LMTUAL lmtUserAccessLevel
LMTUNAME lmtUserName
LOCNAME locationName
OST operationalState
OVPTINS ovptInstalled
PRS proceduralStatus
RELFUNCOBJ relatedFuncObjects
RXDIVSV enableRxDiversitySupervision
SALUNAME salesUniqueName
SCLPRIOLST serviceClassPrioList
VENDNA vendorName
System Responses:Operation Completed
After command execution, a mesNSNe of Changed Configuration Notification is dis-played. A further mesNSNe indicates the result of the operation. An example of get noswl command is the following:
JOB: 48
PC Time&Date: 11:56:22 03/23/2005
NE Time&Date: 12:57:57 09/15/2004
USER NAME: NSN
COMMAND: Get BTSEP NOSWL:NAME=BTSEP:0;
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: Operation successful
alarmStatus = CLEARED
alarmSeverityAcdcp = DEFAULT_DB
alarmSeverityAct = DEFAULT_DB
DN0933412 Issue 01147
BTSplus mainline commands at the Flexi BSC product family
BTSEP
Id:0900d805805b0cba
alarmSeverityCoba = DEFAULT_DB
alarmSeverityBattery = DEFAULT_DB
alarmSeverityCosa = DEFAULT_DB
alarmSeverityCu = DEFAULT_DB
alarmSeverityDidctma = DEFAULT_DB
alarmSeverityDilna = DEFAULT_DB
alarmSeverityDudctma = DEFAULT_DB
alarmSeverityDulna = DEFAULT_DB
alarmSeverityDuvswr = DEFAULT_DB
alarmSeverityFcumain = DEFAULT_DB
alarmSeverityFcutr = DEFAULT_DB
alarmSeverityFanp = DEFAULT_DB
alarmSeverityFtnfp = DEFAULT_DB
alarmSeverityFvswrp = DEFAULT_DB
alarmSeverityLmu = DEFAULT_DB
alarmSeverityTma = DEFAULT_DB
administrativeState = Unlocked
availabilityStatus = NULL
changeOnIDT = IDTWasChanged
enableAutoRecovery = disabled
equipmentPosition = "010101"
lmtLogonSession = ACTIVE
lmtLogonTime =
year = 2003
month = Nov
day = 21
hour = 12
minute = 54
second = 51
JOB: 48
lmtUserAccessLevel = ACCESS_CONTROL_MANAGEMENT
lmtUserName = "NSN"
locationName = "EARTH"
operationalState = ENABLED
ovptInstalled = TRUE
proceduralStatus = NULL
relatedFuncObjects =
148DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805b0cba
BTSEP
BTSM:0
enableRxDiversitySupervision = disabled
salesUniqueName = "NOT_DEFINED"
vendorName = "SIEM."
END OF OUTPUT FOR JOB 48
Operation Failed
The GET command has not been successfully executed. A general NACK will indicate possible errors or a specific NACK strictly related to the single command is possible.
Application Guidelines:
• The attributes have to be set beforehand, otherwise the response will be a Nack mesNSNe
Example of Command Execution:Get BTSEP NOSWL:NAME=BTSE:0,REQATTL=ALRMSEVACDCP&
ALRMSEVACT&ALRMSEVBATTERY&ALRMSEVCOBA&ALRMSEVCOSA&
ALRMSEVCU&ALRMSEVDIDCTMA&ALRMSEVDILNA&ALRMSEVDUDCTMA&
ALRMSEVDULNA&ALRMSEVDUVSWR&ALRMSEVFCUMAIN&ALRMSEVFCUTR&
ALRMSEVFVSWRP&ALRMSEVFTNFP&ALRMSEVFANP&ALRMSEVLMU&
ALRMSEVTMA&ALS&AST&AVS&CHIDT&EAUTOREC& EQUPOS&LMTLSESS&
LMTLTIME&LMTUAL&LMTUNAME&LOCNAME&OST&OVPTINS&PRS&
RELFUNCOBJ&RXDIVSV&SALUNAME&VENDNA;
GET BTSEP SWL
Command Tree:“MANAGED-ELEMENT h BSS-EQUIPMENT h BTSEP h GET BTSEP SWL”
Applicability:Phase 2 and Phase 3.
Visibility level: 0.
Command Description:This command displays the attributes related to the BTSE (BTS Site Equipment).
Long Names:NAME Address of the managed object
REQATTL Required attribute list
SWLDINT swLoadIntended
SWLDSAF swLoadSafety
SWLDST swLoadsStored
GET BTSEP SWL NAME=BTSEP:0..0 ,REQATTL=SWLDINT, SWLDSAF, SWLDST;
DN0933412 Issue 01149
BTSplus mainline commands at the Flexi BSC product family
BTSEP
Id:0900d805805b0cba
System Responses:Operation Completed
After command execution, a mesNSNe of Changed Configuration Notification is dis-played. A further mesNSNe indicates the result of the operation. An example of get swl command is the following:
JOB: 49
PC Time&Date: 11:56:26 03/23/2005
NE Time&Date: 12:58:01 09/15/2004
USER NAME: NSN
COMMAND: Get BTSEP SWL:NAME=BTSEP:0,REQATTL=SWLDINT;
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: Operation successful
swLoadIntended = "HS011726.SWL:02-08-01-01-00-27_04-11-19"
END OF OUTPUT FOR JOB 49
Operation Failed
The GET command has not been successfully executed. A general NACK will indicate possible errors or a specific NACK strictly related to the single command is possible.
Application Guidelines:
• The attributes have to be set beforehand, otherwise the response will be a Nack mesNSNe
• This command has another behaviour than all other commands. If you want all parameters you have to choose its own REQATTL
Example of Command Execution:Get BTSEP SWL:NAME=BTSEP:0,REQATTL=SWLDINT&SWLDSAF&SWLDST;
GET ACTIVEALARMS BTSEP
Command Tree:“MANAGED-ELEMENT h BSS-EQUIPMENT h BTSEP h GETACTIVEALARMS BTSEP”
Applicability:Phase 2 and Phase 3.
GETACTIVEALARMS BTSEP
NAME=BTSEP:0..0 [,EVTYP=];
150DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805b0cba
BTSEP
Visibility level: 0.
Command Description:This command is sent to the BTSE to ask for the active alarms of a certain failure_event_type. A Failre Event Report will be displayed, with the following attributes:
Long Names:NAME Address of the managed object
EVTYP eventType
eventType This attribute specifies the type of failure event alarm.
eventTime It represents the time of the event.
perceivedSeverity This attribute can assume the following values:
indeterminate
criticalFailure
majorFailure
minorFailure
warningLevelFailure
failureCeased
probableCause This attribute indicates the probable cause of the failure.
specificProblem It is a code that has to be referred to the 'Alarm Manual'.
trendIndication This attribute can assume the following values:
lessSevere
noChange
moreSevere
notificationIdentifier The range of this attribute is: 0...4294967295
correlatedNotifications This attribute is composed by the following fields:
identifier: 0...4294967295
relatedMO: object class and object instance refer to the source object in the father event. During state and alarm alignment the state class BTSEP is used.
thresholdInformation This information element is only present if a threshold is assigned to the corresponding alarm and the 'perceived severity' is not 'failure ceased'. If no threshold is exceeded only the observed value is valid.
additionalText This is a string of 26 ASCII characters which are speci-fied by the operator for the corresponding envaBTSE instance (site input). The ASCII characters are not ter-minated by a NULL character
additionalInformation This attribute specifies some additional information (Originator value, FileVersion...)
DN0933412 Issue 01151
BTSplus mainline commands at the Flexi BSC product family
BTSEP
Id:0900d805805b0cba
System Responses:Operation Completed
After command execution, a mesNSNe of Changed Configuration Notification is dis-played. A further mesNSNe indicates the result of the operation. An example of get active alarms command is the following:
JOB: 50
PC Time&Date: 11:56:29 03/23/2005
NE Time&Date: 12:58:04 09/15/2004
USER NAME: NSN
COMMAND: Getactivealarms BTSEP:NAME=BTSEP:0;
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: Operation successful
END OF OUTPUT FOR JOB 50
JOB: 51
PC Time&Date: 11:56:29 03/23/2005
NE Time&Date: 12:58:04 09/15/2004
USER NAME: NSN
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: Operation successful
START ACTIVE ALARM ALIGNMENT BTSEP:
name = BTSEP:0
alignmentRequestNo = 0
notificationIdentifier = 288
END OF OUTPUT FOR JOB 51
JOB: 52
PC Time&Date: 11:56:29 03/23/2005
NE Time&Date: 12:58:04 09/15/2004
152DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805b0cba
BTSEP
USER NAME: NSN
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: Operation successful
END ACTIVE ALARM ALIGNMENT BTSEP:
name = BTSEP:0
alignmentResult = SUCCESSFUL
correlatedNotifications =
correlatedNotificationId = 288
sourceObjectInstance = BTSEP:0
END OF OUTPUT FOR JOB 52
Operation Failed
The GET command has not been successfully executed. A general NACK will indicate possible errors or a specific NACK strictly related to the single command is possible.
Application Guidelines:None.
Example of Command Execution:Getactivealarms BTSEP: NAME=BTSEP:0,
EVTYP= ENVIRONMENTAL_FAILURE_EVENT;
PERFTEST BTSEP
Command Tree:“MANAGED-ELEMENT h BSS-EQUIPMENT h BTSEP h PERFTEST BTSEP”
Applicability:Phase 2 and Phase 3.
Visibility level: 1.
Command Description:This command displays the attributes related to the BTSE (BTS Site Equipment).
Long Names:NAME Address of the managed object
MORT MOT
System Responses:Operation Completed
PERFTEST BTSEP NAME=BTSEP:0..0 ,MORT=;
DN0933412 Issue 01153
BTSplus mainline commands at the Flexi BSC product family
BTSEP
Id:0900d805805b0cba
Test configuration has been set and the specified test has been started. The System response will not be addressed to the MOT but to the object BTSEP
JOB: 55
PC Time&Date: 11:56:59 03/23/2005
NE Time&Date: 12:59:48 09/15/2004
USER NAME: NSN
COMMAND: Perftest BTSEP:NAME=BTSEP:0,MORT=RACK:0;
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: Operation successful
MOT = BTSEP:0,MORT=RACK:0;
tO = BTSETEST:1
END OF OUTPUT FOR JOB 55
JOB: 56
PC Time&Date: 11:57:07 03/23/2005
NE Time&Date: 12:58:42 09/15/2004
USER NAME: NSN
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: Operation successful
ChangedConfigurationNotification:
name = BTSETEST:1
ChangeInfo = created
END OF OUTPUT FOR JOB 56
JOB: 57
PC Time&Date: 11:57:14 03/23/2005
NE Time&Date: 12:58:49 09/15/2004
154DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805b0cba
BTSEP
USER NAME: NSN
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: Operation successful
CHANGED STATE EVENT REPORT:
NAME = BTSEP:0,MORT=RACK:0;
Availability Status = Failed
Notification Identifier = 22
END OF OUTPUT FOR JOB 57
JOB: 58
PC Time&Date: 11:57:24 03/23/2005
NE Time&Date: 12:58:59 09/15/2004
USER NAME: NSN
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: Operation successful
Test Report:
name = BTSETEST:1
testOutcome = FAILED
testTermination = Normal
MOT = BTSEP:0,MORT=RACK:0;
executedPhases =
PreliminaryTestsBtsep
BootEepromTestBtsep
SerialEepromTestBtsep
EndTestBtsep
END OF OUTPUT FOR JOB 58
JOB: 59
PC Time&Date: 11:57:24 03/23/2005
NE Time&Date: 12:58:59 09/15/2004
DN0933412 Issue 01155
BTSplus mainline commands at the Flexi BSC product family
BTSEP
Id:0900d805805b0cba
USER NAME: NSN
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: Operation successful
ChangedConfigurationNotification:
name = BTSETEST:1
ChangeInfo = deleted
END OF OUTPUT FOR JOB 59
The test results will be displayed at the end of the test phases.
Result TEST:
name = TEST:<n>
testOutcome = This field represents the test result; one of the fol-lowing values can be displayed:
Pass all the test phases are successfully performed.
Inconclusive the test is aborted by the system or the test is terminated by the opera-tor.
Fail if at least one of the executed phases fail.
mOts = It is the identifier of the hardware object under test.
testTermination = It specifies how the test is terminated, it can assume the following values:
Normal all the test phases are performed.
Abort the test is aborted by system.
Cancel the test is terminated by operator.
executedPhases
phaseId = It represents the list of the executed test phases (in case of successful test result, all the test phases will be listed).
additionalWords =
....
failedPhases
phaseId = It represents the list of the failed test phase; addi-tional information is provided for each phase.phaseId =
....
skippedPhases
156DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805b0cba
BTSEP
Operation Failed
This NACK-mesNSNe occurs in the following cases: MesNSNe cannot be performed, test not supported, capacity restrictions, physical configuration cannot be performed, object not locked.
Application Guidelines:
• In phase 3 MO must be locked previous to the command execution
Example of Command Execution:Perftest BTSEP:NAME=BTSEP:0,MORT=RACK:0/ACDCP:0;
PING BTSEP
Command Tree:“MANAGED-ELEMENT h BSS-EQUIPMENT h BTSEP h PING BTSEP”
Applicability:Phase 2 and Phase 3.
Visibility level: 0.
Command Description:This command is used to ping the BTSE. After command execution the IP sends a response containing the following information:
• IP address of the target • Alive (TRUE/FALSE)
Long Names:NAME Address of the managed object
IPADR ipAddress
System Responses:Operation Completed
None.
Operation Failed
None.
Application Guidelines:None.
phaseId = It represents the list of the skipped phases; they are displayed only for test stopped during it execution.phaseId =
....
poprosedRepair Action =
A list of most probable fail probable causes is shown (max four mesNSNes)
PING BTSEP NAME=BTSEP:0..0 ,IPADR=;
DN0933412 Issue 01157
BTSplus mainline commands at the Flexi BSC product family
BTSEP
Id:0900d805805b0cba
Example of Command Execution:None.
REQCURSTASYN BTSEP
Command Tree:“MANAGED-ELEMENT h BSS-EQUIPMENT h BTSEP h REQCURSTASYN BTSEP”
Applicability:Phase 3.
Visibility level: 0.
Command Description:new information
Long Names:NAME Address of the managed object
ALGNSTEP alignmentStep
System Responses:Operation Completed
None.
Operation Failed
None.
Application Guidelines:None.
Example of Command Execution:None.
SET BTSEP
Command Tree:“MANAGED-ELEMENT h BSS-EQUIPMENT h BTSEP h SET BTSEP”
Applicability:Phase 2 and Phase 3.
Visibility level: 2.
REQCURSTASYN BTSEP
NAME=BTSEP:0..0 [,ALGNSTEP=];
SET BTSEP NAME=BTSEP:0..0 [,ALIGCOBA=] [,ALRMSEVXXX=] [,CHIDT=] [,EAUTOREC=] [,EQUPOS=] [,GTWADRV4=] [,LOCNAME=] [,OVPTINS=] [,RXDIVSV=] [,SALUNAME=] [,SCLPRIOLST=] [,SWLDSAF=] [,VENDNA=];
158DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805b0cba
BTSEP
Command Description:This command sets general attributes of the BTS Site Equipment (BTSE). A BTSE is the physical equipment which is managed by one BTSM.
Long Names:NAME Address of the managed object
ALIGCOBA alignedCoba
ALRMSEVXXX alarmSeverityXXX
CHIDT changeOnIDT
EAUTOREC enableAutoRecovery
EQUPOS equipmentPosition
GTWADRV4 gatewayAddressIPv4
LOCNAME locationName
OVPTINS ovptInstalled
RXDIVSV enableRxDiversitySupervision
SALUNAME salesUniqueName
SCLPRIOLST serviceClassPrioList
SWLDSAF swLoadSafety
VENDNA vendorName
System Responses:Operation Completed
After command execution, a mesNSNe of Changed Attribute Event Report is displayed. A further mesNSNe indicates the result of the operation. An example of set command is the following:
JOB: 53
PC Time&Date: 11:56:35 03/23/2005
NE Time&Date: 12:58:10 09/15/2004
USER NAME: NSN
COMMAND: Set BTSEP:NAME=BTSEP:0;
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: Operation successful
END OF OUTPUT FOR JOB 53
Operation Failed
The specified attributes have not been set. In addition to the general NACK causes, a specific NACK cause, which indicates that the command is inconsistent with the physical configuration, is possible.
DN0933412 Issue 01159
BTSplus mainline commands at the Flexi BSC product family
BTSEP
Id:0900d805805b0cba
Application Guidelines:
• The supplier recommends the identification of swLoadSafety.
• The swLoadSafety will not be overwritten by a sw download via LMT Evolution
• There is no alignment to one of the SW loads stored on the Flexi BSC product family master database
• The swLoad must be stored in BTSE and must have at least once a connection with the Flexi BSC product family
• The identification of a SW load as the safety one is only accepted by the BTSE if the identified load has been activated and running on this BTSE before
• An update of the swLoadSafety attribute should be performed in each release; the swLoad of the previous release should be used as swLoadSafety
Example of Command Execution:Set BTSEP :NAME=BTSEP:0,ALRMSEVACDCP=CRITICAL,
ALRMSEVACT=CRITICAL,ALRMSEVCOBA=CRITICAL,
ALRMSEVBATTERY=CRITICAL,ALRMSEVCOSA=CRITICAL,
ALRMSEVCU=CRITICAL,ALRMSEVDIDCTMA=CRITICAL,
ALRMSEVDILNA=CRITICAL,ALRMSEVDUDCTMA=CRITICAL,
ALRMSEVDULNA=CRITICAL,ALRMSEVDUVSWR=CRITICAL,
ALRMSEVFCUMAIN= CRITICAL,ALRMSEVFCUTR= CRITICAL,
ALRMSEVFANP= CRITICAL,ALRMSEVFTNFP=CRITICAL,
ALRMSEVFVSWRP=CRITICAL,EQUPOS="020101",CHIDT=noChangeOnIDT,
EAUTOREC=disabled,LOCNAME="MUNICH",OVPTINS=true,RXDIVSV=enabled,
SALUNAME="AD042S7449E",SWLDSAF="HS011726.SWL:02-04-17-01-13-00_04-09-03",VENDNA="SIEMENS";
STOPTEST BTSEP
Command Tree:“MANAGED-ELEMENT h BSS-EQUIPMENT h BTSEP h STOPTEST BTSEP”
Applicability:Phase 2 and Phase 3.
Visibility level: 1.
Command Description:This command requires the stop of the test on BTSE Plus.
Long Names:NAME Address of the managed object
MORT MOT
TESTNO testNo
STOPTEST BTSEP NAME=BTSEP:0..0 [,MORT=] [,TESTNO=];
160DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805b0cba
BTSEP
System Responses:Operation Completed
Test has been stopped.
Operation Failed
Application Guidelines:None.
Example of Command Execution:Stoptest BTSEP:NAME=BTSEP:0, MORT=RACK:0/ACDCP:0,TESTNO=23;
Test has not been stopped. This NACK-mesNSNe can occur when the specified test is not running or in case of test which cannot be stopped.
TEST REPORT: The TEST REPORT provides a list of executed, failed and skipped phases.
DN0933412 Issue 01161
BTSplus mainline commands at the Flexi BSC product family
BTSETEST
Id:0900d805805b0cbc
BTSETESTThe TEST locates a test object in the system. This object is created when an activation of a diagnostic occurs.
GET BTSETEST
Command Tree:“MANAGED-ELEMENT h BSS-EQUIPMENT h BTSEP h BTSETEST h GET BTSETEST”
Applicability:Phase 2 and Phase 3.
Visibility level: 0.
Command Description:This command displays the attributes related to a test. The values 1-255 will be used for the allocated 'test object instance' to keep track of the related 'MORTs'.
Long Names:NAME Address of the managed object
REQATTL Required attribute list
MORT MOT
TESTMON testMonitor
TESTOUT testOutcome
TESTST testState
System Responses:Operation Completed
The output includes a test report containing "Executed Phases", "Failed Phases", "Tes-tOutcome", "Test Termination", "MOT". An example of "Test Report" is the following:
JOB: 19
PC Time&Date: 11:32:14 03/23/2005
NE Time&Date: 11:30:55 09/15/2004
USER NAME: NSN
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: Operation successful
Test Report BTSETEST:
GET BTSETEST NAME=BTSETEST:1..255 [,REQATTL=MORT, TESTMON, TESTOUT, TESTST];
162DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805b0cbc
BTSETEST
name = BTSETEST:1
testOutcome = PASSED
testTermination = Normal
MOT = RACK:0/CU:2
executedPhases =
PreliminaryTestsAct
CheckAlarmStatusAct
EndTestAct
END OF OUTPUT FOR JOB 19
Operation Failed
The GETTEST command has not been successfully executed.
A general NACK will indicate possible errors or a specific NACK strictly related to the single command is possible.
Application Guidelines:
• Only intrusive tests are supported
• For TESTOUT attribute the value inconclusive is possible only during the start phase. It indicates that no "Pass" or "Fail" outcome has been determined yet
Example of Command Execution:Get BTSETEST :NAME=BTSETEST:1,REQATTL=MORTS&TESTMON&
TESTOUT&TESTST;
DN0933412 Issue 01163
BTSplus mainline commands at the Flexi BSC product family
BTSM
Id:0900d805805b0cc0
BTSMThe BTSM object provides services to control the functionalities of one or more BR BTS NEs (BTSplus mainline, eMicro, BTSplus basic) located at the same site. It performs all the operation and maintenance functions common to all transceivers.
ACTIVATE BTSM
Command Tree:“MANAGED-ELEMENT h BSS-FUNCTIONAL h BTSM h ACTIVATE BTSM”
Applicability:Phase 1 and Phase 2 and Phase 3.
Visibility level: 2.
Command Description:This command activates one of the three SW loads stored in the BTSE.
Long Names:NAME Address of the managed object
FILEID fileId
FILESWV fileVersion
System Responses:Operation Completed
Download START:
JOB: 181
PC Time&Date: 12:06:21 03/23/2005
NE Time&Date: 13:07:57 09/15/2004
USER NAME: NSN
COMMAND: Activate BTSM:NAME=BTSM:0,FILEID="HS011726.SWL:01-04-16-01-59-00_03-11-18";
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: Operation successful
fileId = "HS011722.SWL"
fileVersion = "01-04-17-01-26-51_05-02-23"
END OF OUTPUT FOR JOB 181
ACTIVATE BTSM NAME=BTSM:0..0 ,FILEID= ,FILESWV=;
164DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805b0cc0
BTSM
JOB: 182
PC Time&Date: 12:06:21 03/23/2005
NE Time&Date: 13:07:57 09/15/2004
USER NAME: NSN
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: Operation successful
ID_Message
END OF OUTPUT FOR JOB 182
SW ACTIVATED REPORT:
(a report is displayed)
Operation Failed
(Invalid SVR)
Application Guidelines:
• If an incorrect FileVersion is given the system rejects the command
• This command is followed by a reset of the BTSE
• If the currently running SW version is activated by the command, the SW will be dis-tributed again in the BTSE
• If the intended SW is corrupted, the BTSE first tries to come up with the safety load; if this is not successful, the BTSE tries to start the third SWload, the dischargeable one
• The FileId is a parameter used within the SW download procedures and not of the type 'GET'. The corresponding attribute is SWLCFID and is related only to the swLoad-header file. All characters of the ASCII string are to be in upper case. However, the SW parts in the BTSE handling the file Id are to be case tolerant
• The FileVersion is a parameter used within the SW download procedures and not of the type 'GET'. The corresponding attribute is SWLCVER which is coded identical as File Version. However the allowed values for 'hh' are different because SWLCVER is related only to the swLoad-header file
Example of Command Execution:Activate BTSM:NAME=BTSM:0,FILEID="vHS011722.SWL",FILESWV="02-04-16-
01-05-01_03_02_25"
DN0933412 Issue 01165
BTSplus mainline commands at the Flexi BSC product family
BTSM
Id:0900d805805b0cc0
ACTIVATE_DELAYED BTSM
Command Tree:“MANAGED-ELEMENT h BSS-FUNCTIONAL h BTSM h ACTIVATE_DELAYED BTSM”
Applicability:Phase 2 and Phase 3.
Visibility level: 2.
Command Description:This command activates one of the three SW loads stored in the BTSE with a defined delayed time.
Long Names:NAME Address of the managed object
FILEID fileId
FILESWV fileVersion
TIMEDELAY timeDelay(sec)
System Responses:Operation Completed
USER NAME: NSN
COMMAND: Activate_delayed BTSM:NAME=BTSM:0,FIL-EID="123456789123",FILESWV="01-01-16-00-56-00_03-10-16",TIMEDELAY=3;
SW RELEASE: 01-01-17-00-26-51_05-02-23
COMMAND RESULT: Operation successful
Operation Failed
None.
Application Guidelines:None.
Example of Command Execution:Activate_delayed BTSM:NAME=BTSM:0,FILEID="123456789123",FILESWV="01-01-16-00-56-00_03-10-16",TIMEDELAY=3;
CONNBSC BTSM
Command Tree:“MANAGED-ELEMENT h BSS-FUNCTIONAL h BTSM h CONNBSC BTSM”
ACTIVATE_DELAYED BTSM
NAME=BTSM:0..0 ,FILEID= ,FILESWV= ,TIMEDELAY=;
CONNBSC BTSM NAME=BTSM:0..0;
166DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805b0cc0
BTSM
Applicability:Phase 2.
Visibility level: 1.
Command Description:This command starts the connection between the BTSplus mainline and the Flexi BSC product family and is followed by a transition from LMT Evolution Phase 2 to LMT Evo-lution Phase 3.
Long Names:NAME Address of the managed object
System Responses:Operation Completed
The command has been correctly executed.
JOB: 180
PC Time&Date: 12:06:20 03/23/2005
NE Time&Date: 00:00:00 00/00/0
USER NAME: NSN
COMMAND: Connbsc BTSM:NAME=BTSM:0;
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: Operation successful
END OF OUTPUT FOR JOB 180
SWACTIVATED REPORT
Operation Failed
The command has not been correctly executed.
Application Guidelines:
• After the execution of this command, the BTSM will be in the administrative state "Unlocked"
• If one of the "Minimal Parameters" of the BTSE is in the locked state, no connection to the BSC is possible
• The CCLK accuracy must be "Medium" or "High" before the connection to the BSC is possible
• The BTSM attribute TEI has to be defined
• The BPORT object has to be defined previous LAPDLE
• The LAPDLE object has to be defined
DN0933412 Issue 01167
BTSplus mainline commands at the Flexi BSC product family
BTSM
Id:0900d805805b0cc0
• For Radio Commander purposes the SALUNAME and TYPRACK attributes have to be set. Otherwise the OMC cannot identify the BTSE
Example of Command Execution:Connbsc BTSM:NAME=BTSM:0;
DISCBSC BTSM
Command Tree:“MANAGED-ELEMENT h BSS-FUNCTIONAL h BTSM h DISCBSC BTSM”
Applicability:Phase 3.
Visibility level: 1.
Command Description:This command disconnects the BTSplus main line from the Flexi BSC product family and is followed by a transition from LMT Evolution Phase 3 to LMT Evolution Phase 2.
Long Names:NAME Address of the managed object
System Responses:Operation Completed
The command has been correctly executed.
JOB: 179
PC Time&Date: 12:06:20 03/23/2005
NE Time&Date: 00:00:00 00/00/0
USER NAME: NSN
COMMAND: Discbsc BTSM:NAME=BTSM:0;
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: Operation successful
END OF OUTPUT FOR JOB 179
Operation Failed
The command has not been correctly executed.
DISCBSC BTSM NAME=BTSM:0..0;
168DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805b0cc0
BTSM
Application Guidelines:
• If a connection to the BSC is established, the BTSM must be in the administrative state "Locked"
• If the SW in BTSM in BSC is not the same like in BTSE, BTSM cannot be locked
(At BSC disk no SW is available) and you cannot come to Phase 2. To come to phase 2 you have to make a COBA manual reset
Example of Command Execution:Discbsc BTSM:NAME=BTSM:0;
FWUPGRADE BTSM
Command Tree:“MANAGED-ELEMENT h BSS-FUNCTIONAL h BTSM h FWUPGRADE BTSM”
Applicability:Phase 2 and Phase 3.
Visibility level: 2.
Command Description:new information
Long Names:NAME Address of the managed object
FILEID fileId
FILEFWV fwVersion
LRU lru
ACTVINC activationIncluded
System Responses:Operation Completed
None.
Operation Failed
None.
Application Guidelines:None.
Example of Command Execution:None.
FWUPGRADE BTSM NAME=BTSM:0..0 ,FILEID= ,FILEFWV= [,LRU=] [,ACT-VINC=];
DN0933412 Issue 01169
BTSplus mainline commands at the Flexi BSC product family
BTSM
Id:0900d805805b0cc0
GET BTSM NOSWL
Command Tree:“MANAGED-ELEMENT h BSS-FUNCTIONAL h BTSM h GET BTSM NOSWL”
Applicability:Phase 2 and Phase 3.
Visibility level: 0.
Command Description:This command displays the attributes related to the BTSM (BTS Site Manager).
Long Names:NAME Address of the managed object
REQATTL Required attribute list
ABISLKSAT sAbisLinkSatellited
ABISTIME sAbisExternalTime
ASUBLKSAT sAsubLinkSatellited
AST administrativeState
AVS availabilityStatus
DYNTRACGRAN dynTraceGranularity
EINTSITSYN enableInterSiteSync
EMT1 emergencyTimer1(min)
EMT2 emergencyTimer2(min)
LPDLMSAT lapdleLinkSatellited
OMLAPDRT omLapdRelTimer(sec)
OST operationalState
RELEQUIPOBJ relatedEquipObjects
TEI tei
TSLPOOL tslPool
SHLAPDIT shortLapdIntTimer(sec)
System Responses:Operation Completed
After command execution, a message of Changed Configuration Notification is dis-played. A further message indicates the result of the operation. An example of get noswl command is the following:
JOB: 20
GET BTSM NOSWL NAME=BTSM:0..0 [,REQATTL=ABISLKSAT, ABISTIME, ASUBLKSAT, AST, AVS, DYNTRACGRAN, EINTSITSYN, EMT1, EMT2, LPDLMSAT, OMLAPDRT, OST, RELEQUI-POBJ, TEI, TSLPOOL, SHLAPDIT];
170DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805b0cc0
BTSM
PC Time&Date: 11:33:34 03/23/2005
NE Time&Date: 11:31:25 09/15/2004
USER NAME: NSN
COMMAND: Get BTSM NOSWL:NAME=BTSM:0;
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: Operation successful
administrativeState = Unlocked
availabilityStatus = NULL
dynTraceGranularity = 1
emergencyTimer1(min) = 10
emergencyTimer2(min) = 0
enableInterSiteSync = FALSE
lapdleLinkSatellited = terrestrialConnection
omLapdRelTimer(sec) = 30
operationalState = ENABLED
relatedEquipObjects =
HMO = BTSEP:0
sAbisExternalTime =
Year = 2003
Month = Jan
Day = 1
Hour = 20
Minute = 16
Second = 3
sAbisLinkSatellited = terrestrialConnection
sAsubLinkSatellited = terrestrialConnection
shortLapdIntTimer(sec) = 15
tei = 0
JOB: 20
tslPool =
TS01 TS02 TS03 TS04 TS05 TS06 TS07 TS08
TS09 TS10 TS11 TS12 TS13 TS14 TS15 TS16
TS17 TS18 TS19 TS20 TS21 TS22 TS23 TS24
TS25 TS26 TS27 TS28 TS29 TS30 TS31
BPORT0
DN0933412 Issue 01171
BTSplus mainline commands at the Flexi BSC product family
BTSM
Id:0900d805805b0cc0
0000 0000 0000 0000 1111 1111 0000 0000
0000 0000 0000 0000 0000 0000 0000 0000
0000 0000 0000 0000 0000 0000 0000 0000
0000 0000 0000 0000 0000 0000 0000
END OF OUTPUT FOR JOB 23
Operation Failed
The GET command has not been successfully executed. A general NACK will indicate possible errors or a specific NACK strictly related to the single command is possible.
Application Guidelines:
• In order to decide whether a "fast" alignment instead of a "full" one must be started, the BSC reads the shortLAPDIntTimer and increases it of a value currently fixed to 30 seconds; for this reason the suggested values are
shortLAPDIntTimer:
• max. attribute length for attribute tslPool increased to 136
Example of Command Execution:Get BTSM NOSWL:NAME=BTSM:0,REQATTL=ABISLKSAT&ABISTIME&
AST&ASUBLKSAT&AVS&DYNTRACGRAN&EMT1&EMT2&EINTSITSYN&
LPDLMSAT&OMLAPDRT&OST&RELEQUIPOBJ&SHLAPDIT&TEI&TSLPOOL;
GET BTSM OVERLOAD
Command Tree:“MANAGED-ELEMENT h BSS-FUNCTIONAL h BTSM h GET BTSM OVERLOAD”
Applicability:Phase 2 and Phase 3.
Visibility level: 0.
Command Description:This command displays the attributes related to the BTSM (BTS Site Manager).
Long Names:NAME Address of the managed object
REQATTL Required attribute list
LAPDOVLTH lapdOverloadThresholds(%)
LAPDOVLT lapdOverloadTimer(sec)
System Responses:Operation Completed
GET BTSM OVERLOAD NAME=BTSM:0..0 ,REQATTL=LAPDOVLTH, LAPDOVLT;
172DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805b0cc0
BTSM
After command execution, a message of Changed Configuration Notification is dis-played. A further message indicates the result of the operation. An example of get overload command is the following:
JOB: 23
PC Time&Date: 11:33:34 03/23/2005
NE Time&Date: 11:31:25 09/15/2004
USER NAME: NSN
COMMAND: Get BTSM OVERLOAD:NAME=BTSM:0;
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: Operation successful
lapdOverloadTimer = 10
lapdOverloadThresholds(%) =
firstLevUpperThreshold = 80
firstLevLowerThreshold = 70
secLevUpperThreshold = 90
secLevLowerThreshold = 80
lapdOverloadTRXList =
END OF OUTPUT FOR JOB 23
Operation Failed
The GET command has not been successfully executed. A general NACK will indicate possible errors or a specific NACK strictly related to the single command is possible.
Application Guidelines:
• The number of possible TRX instances for attribute lapdOverloadTrxList increased to 48.
Example of Command Execution:Get BTSM OVERLOAD:NAME=BTSM:0,REQATTL=LAPDOVLT&LAPDOVLTH;
GET BTSM SWL
Command Tree:“MANAGED-ELEMENT h BSS-FUNCTIONAL h BTSM h GET BTSM SWL”
Applicability:Phase 2 and Phase 3.
Visibility level: 0.
GET BTSM SWL NAME=BTSM:0..0 ,REQATTL=SWLCFID, SWLCVER;
DN0933412 Issue 01173
BTSplus mainline commands at the Flexi BSC product family
BTSM
Id:0900d805805b0cc0
Command Description:This command displays the attributes related to the BTSM (BTS Site Manager).
Long Names:NAME Address of the managed object
REQATTL Required attribute list
SWLCFID swLoadCurrentFileId
SWLCVER swLoadCurrentFileVersion
System Responses:Operation Completed
After command execution, a message of Changed Configuration Notification is dis-played. A further message indicates the result of the operation. An example of get swl command is the following:
JOB: 178
PC Time&Date: 12:06:19 03/23/2005
NE Time&Date: 13:03:28 09/15/2004
USER NAME: NSN
COMMAND: Get BTSM SWL:NAME=BTSM:0
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: Operation successful
superordinateBscSwLoadCurrentVersion = "02-08-01-01-00-30_04-12-14"
swLoadCurrentFileId = "hs011713.SWL"
swLoadCurrentFileVersion = "01-04-17-01-26-51_05-02-23"
END OF OUTPUT FOR JOB 178
Operation Failed
The GET command has not been successfully executed. A general NACK will indicate possible errors or a specific NACK strictly related to the single command is possible.
Application Guidelines:None.
Example of Command Execution:Get BTSM SWL:NAME=BTSM:0,SWLCFID&SWLCVER;
174DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805b0cc0
BTSM
LOCKREQUEST BTSM
Command Tree:“MANAGED-ELEMENT h BSS-FUNCTIONAL h BTSM h LOCKREQUEST BTSM”
Applicability:Phase 3.
Visibility level: 1.
Command Description:This command sends a request to the BSC for immediate locking of the BTSM.
Long Names:NAME Address of the managed object
System Responses:Operation Completed
The specified change of administrative state has been perfomed.
JOB: 56
PC Time&Date: 11:57:07 03/23/2005
NE Time&Date: 12:58:42 09/15/2004
USER NAME: NSN
COMMAND: Lockrequest BTSM:NAME=BTSM:0;
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: Operation successful
END OF OUTPUT FOR JOB 56
CHANGED STATE EVENT REPORT:
This provides information about the administrative state, the operational state and the availability status every time a state change occurs.
Operation Failed
The specified change of administrative state has not been performed.
Application Guidelines:
• This command should only be used when the system is in real danger. The Shutdown command is preferred
LOCKREQUEST BTSM NAME=BTSM:0..0;
DN0933412 Issue 01175
BTSplus mainline commands at the Flexi BSC product family
BTSM
Id:0900d805805b0cc0
Example of Command Execution:Lockrequest BTSM:NAME=BTSM:0;
SET BTSM
Command Tree:“MANAGED-ELEMENT h BSS-FUNCTIONAL h BTSM h SET BTSM”
Applicability:Phase 2.
Visibility level: 2.
Command Description:This command sets the attributes of the BTS_Site_Manager (BTSM). The BTS Site Manager represents the O&M functionality related to a site and not to any specific BTSplus mainline. A site is a logical grouping of one or more BTSplus mainlines at a single physical location with common management needs. This configuration has to match with the related functional object in the Flexi BSC product family.
Long Names:NAME Address of the managed object
ABISLKSAT sAbisLinkSatellited
ABISTIME sAbisExternalTime
System Responses:Operation Completed
After command execution, a message of Changed Attribute Event Report is displayed. A further message indicates the result of the operation. An example of set command is the following:
JOB: 177
PC Time&Date: 12:06:04 03/23/2005
NE Time&Date: 13:07:40 09/15/2004
USER NAME: NSN
COMMAND: Set BTSM:NAME=BTSM:0;
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: Operation successful
END OF OUTPUT FOR JOB 177
Operation Failed
SET BTSM NAME=BTSM:0..0 [,ABISLKSAT=] [,ABISTIME=];
176DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805b0cc0
BTSM
The specified attributes have not been set. In addition to the general NACK causes, a specific NACK cause, which indicates that the command is inconsistent with the physical configuration, is possible.
Application Guidelines:
• The BPortNumber must be the same for all abisChannel attributes of the CHAN instances of the same TRX
• Except for timeslot 0 (Synchronization Time Slot) all time slots can be used to support both, traffic or signalling channels
• The ABISTIME attribute is useful for longer operation on site. In transition from Phase 2 to Phase 3 this attribute is overwritten by the BSC
• Setting of ABISLKSAT in the BTSE and of LPDLMSAT in BSC must be homoge-nous:
- terrestrialConnection (corresponds in the BSC to 'LPDLMSAT=FALSE')
- satelliteConnection (corresponds in the BSC to 'LPDLMSAT=TRUE')
Example of Command Execution:Set BTSM:NAME=BTSM:0,ABISLKSAT=terrestrialConnection, ABISTIME=1999-Oct-28-18-0-0
SHUTDOWN BTSM
Command Tree:“MANAGED-ELEMENT h BSS-FUNCTIONAL h BTSM h SHUTDOWN BTSM”
Applicability:Phase 3.
Visibility level: 1.
Command Description:This command will not allow new telecom traffic to be transferred to the BTSM (no incoming handover, no paging, no call set up). When all calls are terminated, the transfer to "Locked" will be performed automatically.
Long Names:NAME Address of the managed object
System Responses:Operation Completed
The specified change of administrative state has been perfomed.
JOB: 59
PC Time&Date: 11:57:24 03/23/2005
NE Time&Date: 12:58:59 09/15/2004
SHUTDOWN BTSM NAME=BTSM:0..0;
DN0933412 Issue 01177
BTSplus mainline commands at the Flexi BSC product family
BTSM
Id:0900d805805b0cc0
USER NAME: NSN
COMMAND: Shutdown BTSM:NAME=BTSM:0;
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: Operation successful
END OF OUTPUT FOR JOB 59
CHANGED STATE EVENT REPORT:
This provides information about the administrative state, the operational state and the availability status every time a state change occurs.
Operation Failed
The specified change of administrative state has not been performed.
Application Guidelines:None.
Example of Command Execution:Shutdown BTSM:NAME=REMINV:0;
UNLOCKREQUEST BTSM
Command Tree:“MANAGED-ELEMENT h BSS-FUNCTIONAL h BTSM h UNLOCKREQUEST BTSM”
Applicability:Phase 3.
Visibility level: 1.
Command Description:This command sends a request to the BSC for the unlocking of the BTSM. The BTSM will be able to handle telecom traffic.
Long Names:NAME Address of the managed object
System Responses:Operation Completed
The specified change of administrative state has been perfomed.
JOB: 57
UNLOCKREQUEST BTSM
NAME=BTSM:0..0;
178DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805b0cc0
BTSM
PC Time&Date: 11:57:14 03/23/2005
NE Time&Date: 12:58:49 09/15/2004
USER NAME: NSN
COMMAND: Unlockrequest BTSM:NAME=BTSM:0;
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: Operation successful
END OF OUTPUT FOR JOB 57
CHANGED STATE EVENT REPORT:
This provides information about the administrative state, the operational state and the availability status every time a state change occurs.
Operation Failed
The specified change of administrative state has not been performed.
Application Guidelines:
• Unlocking of BTSM causes a full BTSplus mainline alignment
• In case of issuing BTSE configuration commands during an alignment, a new align-ment will be started
Example of Command Execution:Unlockrequest BTSM:NAME=BTSM:0;
DN0933412 Issue 01179
BTSplus mainline commands at the Flexi BSC product family
CESPW
Id:0900d805805b0cc2
CESPWThe CESPW object represents one UDP stream which is both received and simultane-ously transmitted to the peer. The object is introduced for the following purposes:
• Setting of the UPD port numbers
• Configuration of the mapping between CESoPSN payload and internal TDM highways
• Adjustment of packetization latency (transmission) and jitter buffer (reception)
CREATE CESPW
Command Tree:“MANAGED-ELEMENT h BSS-EQUIPMENT h BTSEP h CESPW h CREATE CESPW”
Applicability:Phase 2 and Phase 3.
Visibility level: 2.
Command Description:This command adds the CESPW to the BTSE data base.
Long Names:NAME Address of the managed object
PWNAME pwName
LOCLUDP localUdpPort
PEERUDPPORT peerUdpPort
TDMAP tdmMapping
PKTLAT packetizationLatency
MAXPDV maxPdv(ms)
System Responses:Operation Completed
After command execution, a message of Changed Configuration Notification is dis-played. A further message indicates the result of the operation. An example of create command is the following:JOB: 60
PC Time&Date: 02.04.2008 09:10:46 +02:00.
NE Time&Date: 01.01.1990 18:26:24 +00:00
USER NAME: NSN
COMMAND: Create CESPW:NAME=CESPW:0,LOCLUDP=49200,PEERUDP=
49200,TDMAP=1-2-3-4-0-0-0-0-0-0-0-0-0-0-0-0-0-0-0-0-0-0-0-0-0-0-0-0-0-0-0;
SW RELEASE: 01-04-19-01-08-CR_08-03-31
CREATE CESPW NAME=CESPW:0..7 [,PWNAME=] ,LOCLUDP= ,PEERUD-PPORT= ,TDMAP= [,PKTLAT=] [,MAXPDV=];
180DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805b0cc2
CESPW
COMMAND RESULT:Operation successful
localUdpPort = 49200
peerUdpPort = 49200
tdmMapping =
pTs1 = 1
pTs2 = 2
pTs3 = 3
pTs4 = 4
pTs5 = 0
pTs6 = 0
pTs7 = 0
pTs8 = 0
pTs9 = 0
pTs10 = 0
pTs11 = 0
pTs12 = 0
pTs13 = 0
pTs14 = 0
pTs15 = 0
pTs16 = 0
pTs17 = 0
pTs18 = 0
pTs19 = 0
pTs20 = 0
pTs21 = 0
pTs22 = 0
pTs23 = 0
pTs24 = 0
pTs25 = 0
pTs26 = 0
pTs27 = 0
pTs28 = 0
pTs29 = 0
pTs30 = 0
pTs31 = 0
END OF OUTPUT FOR JOB 60
Operation Failed
None.
DN0933412 Issue 01181
BTSplus mainline commands at the Flexi BSC product family
CESPW
Id:0900d805805b0cc2
Application Guidelines:
• The creation of a CESPW instance is rejected if no CESTUNNEL has been created before
Example of Command Execution:Create CESPW:NAME=CESPW:0,LOCLUDP=49153,MAXPDV=16,PEER-UDP=49152,PKTLAT=m1000,PWN="trial1",TDMAP=1-1-1-1-1-1-1-1-1-1-1-1-1-1-1-1-1-1-1-1-1-1-1-1-1-1-1-1-1-1-1;
DELETE CESPW
Command Tree:“MANAGED-ELEMENT h BSS-EQUIPMENT h BTSEP h CESPW h DELETE CESPW”
Applicability:Phase 2 and Phase 3.
Visibility level: 2.
Command Description:This command deletes the CESPW from the BTSE data base.
Long Names:NAME Address of the managed object
System Responses:Operation Completed
After command execution, a message of Changed Configuration Notification is dis-played. A further message indicates the result of the operation. An example of delete command is the following:
JOB: 503.
PC Time&Date: 05.06.2008 13:45:42 +02:00
NE Time&Date: 01.01.1990 00:42:25 +00:00
USER NAME: NSN
COMMAND: Delete CESPW:NAME=CESPW:7;
SW RELEASE: 01-04-19-01-09-ZS_08-06-05
COMMAND RESULT:Operation successful
END OF OUTPUT FOR JOB 503
Operation Failed
None.
Application Guidelines:None.
DELETE CESPW NAME=CESPW:0..7;
182DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805b0cc2
CESPW
Example of Command Execution:Delete CESPW:NAME=CESPW:0;
GET CESPW
Command Tree:“MANAGED-ELEMENT h BSS-EQUIPMENT h BTSEP h CESPW h GET CESPW”
Applicability:Phase 2 and Phase 3.
Visibility level: 0.
Command Description: This command displays the attributes of the CESPW.
Long Names:NAME Address of the managed object
REQATTL Required attribute list
ALS alarmStatus
AST administrativeState
AVS availabilityStatus
OST operationalState
PRS proceduralStatus
RELFUNCOBJ relatedFuncObjects
PWNAME pwName
LOCLUDP localUdpPort
PEERUDPPORT peerUdpPort
TDMAP tdmMapping
PKTLAT packetizationLatency
MAXPDV maxPdv(ms)
System Responses:Operation Completed
A message indicates the result of the operation. An example of get command is the fol-lowing:
JOB: 9
PC Time&Date: 02.10.2008 09:06:43 +02:00
NE Time&Date: 02.10.2008 06:50:36 +01:00
USER NAME: NSN
GET CESPW NAME=CESPW:0..7 [,REQATTL=ALS, AST, AVS, OST, PRS, RELFUNCOBJ, PWNAME, LOCLUDP, PEERUDP-PORT, TDMAP, PKTLAT, MAXPDV];
DN0933412 Issue 01183
BTSplus mainline commands at the Flexi BSC product family
CESPW
Id:0900d805805b0cc2
COMMAND: Get CESPW:NAME=CESPW:0;
SW RELEASE: 01-04-19-01-12-ZT_08-09-29
COMMAND RESULT:Operation successful
alarmStatus = CLEARED
administrativeState = Unlocked
availabilityStatus = NULL
operationalState = ENABLED
proceduralStatus = NULL
relatedFuncObjects = Null
pwName = "Null"
localUdpPort = 49300
peerUdpPort = 49300
tdmMapping =
pTs1 = 1
pTs2 = 2
pTs3 = 3
pTs4 = 4
pTs5 = 5
pTs6 = 0
pTs7 = 0
pTs8 = 0
pTs9 = 0
pTs10 = 0
pTs11 = 0
pTs12 = 0
pTs13 = 0
pTs14 = 0
pTs15 = 0
pTs16 = 0
pTs17 = 0
pTs18 = 0
pTs19 = 0
pTs20 = 0
pTs21 = 0
pTs22 = 0
pTs23 = 0
pTs24 = 0
pTs25 = 0
pTs26 = 0
184DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805b0cc2
CESPW
pTs27 = 0
pTs28 = 0
pTs29 = 0
pTs30 = 0
pTs31 = 0
packetizationLatency = m1000
maxPdv(ms) = 2.000
END OF OUTPUT FOR JOB 9
Operation Failed
None.
Application Guidelines:None.
Example of Command Execution:Get CESPW:NAME=CESPW:0;REQATTL=ALS&AST&AVS&OST&PRS&RELFUN-COBJ&PWN&LOCLUDP&PEERUDP&TDMAP&PKTLAT&MAXPDV;
LOCK CESPW
Command Tree:“MANAGED-ELEMENT h BSS-EQUIPMENT h BTSEP h CESPW h LOCK CESPW”
Applicability:Phase 2 and Phase 3.
Visibility level: 1.
Command Description:This command changes the administrative state of CESPW.
Long Names:NAME Address of the managed object
System Responses:Operation Completed
The specified change of administrative state has been perfomed. An example of lock command is the following:
JOB: 29
PC Time&Date: 05.06.2008 13:06:00 +02:00
NE Time&Date: 01.01.1990 00:02:44 +00:00
USER NAME: NSN
COMMAND: Lock CESPW:NAME=CESPW:0;
SW RELEASE: 01-04-19-01-09-ZS_08-06-03
LOCK CESPW NAME=CESPW:0..7;
DN0933412 Issue 01185
BTSplus mainline commands at the Flexi BSC product family
CESPW
Id:0900d805805b0cc2
COMMAND RESULT:Operation successful
administrativeState = Locked
END OF OUTPUT FOR JOB 29
Operation Failed
None.
Application Guidelines:None.
Example of Command Execution:Lock CESPW:NAME=CESPW:0;
SET CESPW
Command Tree:“MANAGED-ELEMENT h BSS-EQUIPMENT h BTSEP h CESPW h SET CESPW”
Applicability:Phase 2 and Phase 3.
Visibility level: 2.
Command Description:This command sets the attributes of CESPW to the BTSE data base.
Long Names:NAME Address of the managed object
PWNAME pwName
LOCLUDP localUdpPort
PEERUDPPORT peerUdpPort
TDMAP tdmMapping
PKTLAT packetizationLatency
MAXPDV maxPdv(ms)
System Responses:Operation Completed
After command execution, a message of Changed Configuration Notification is dis-played. A further message indicates the result of the operation. An example of set command is the following:
JOB: 32
PC Time&Date: 05.06.2008 13:06:09 +02:00
NE Time&Date: 01.01.1990 00:02:53 +00:00
USER NAME: NSN
SET CESPW NAME=CESPW:0..7 [,PWNAME=] [,LOCLUDP=] [,PEER-UDPPORT=] [,TDMAP=] [,PKTLAT=] [,MAXPDV=];
186DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805b0cc2
CESPW
COMMAND: Set CESPW:NAME=CESPW:0,MAXPDV=0.125;
SW RELEASE: 01-04-19-01-09-ZS_08-06-03
COMMAND RESULT:Operation successful
maxPdv = 0.125
END OF OUTPUT FOR JOB 32
Operation Failed
None.
Application Guidelines:
• Any modification of the mapping is allowed only if the CESPW has been previously locked
Example of Command Execution:Set CESPW:NAME=CESPW:0,LOCLUDP=49152,MAXPDV=16,PEER-UDP=49152,PKTLAT=m1000,PWN="trial1",TDMAP=1-1-1-1-1-1-1-1-1-1-1-1-1-1-1-1-1-1-1-1-1-1-1-1-1-1-1-1-1-1-1;
UNLOCK CESPW
Command Tree:“MANAGED-ELEMENT h BSS-EQUIPMENT h BTSEP h CESPW h UNLOCK CESPW”
Applicability:Phase 2 and Phase 3.
Visibility level: 1.
Command Description:This command changes the administrative state of CESPW.
Long Names:NAME Address of the managed object
System Responses:Operation Completed
The specified change of administrative state has been perfomed. An example of unlock command is the following:
JOB: 84
PC Time&Date: 05.06.2008 13:17:19 +02:00NE Time&Date: 01.01.2000 00:14:03 +00:00
USER NAME: NSN
COMMAND: Unlock CESPW:NAME=CESPW:0;
SW RELEASE: 01-04-19-01-09-ZS_08-06-03
COMMAND RESULT:Operation successful
UNLOCK CESPW NAME=CESPW:0..7;
DN0933412 Issue 01187
BTSplus mainline commands at the Flexi BSC product family
CESPW
Id:0900d805805b0cc2
administrativeState = Unlocked
END OF OUTPUT FOR JOB 84
Operation Failed
None.
Application Guidelines:None.
Example of Command Execution:Unlock CESPW:NAME=CESPW:0;
188DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805b0cc4
CESTUNNEL
CESTUNNELThis object represents the PSN tunnel. As the BTSE is uniquely connected to one Flexi BSC product family there is only one CESTUNNEL instance per BTSE. The CESTUN-NEL object is introduced for the following purposes:
• Setting of the local (BTSE) and peer IP address
• Setting of attributes which apply for all pseudo wires
CREATE CESTUNNEL
Command Tree:“MANAGED-ELEMENT h BSS-EQUIPMENT h BTSEP h CESTUNNEL h CREATE CESTUNNEL”
Applicability:Phase 2.
Visibility level: 2.
Command Description:This command adds the CESTUNNEL to the BTSE data base.
Long Names:NAME Address of the managed object
LOCALADDR localAddress
PEERADDR peerAddress
VLANID vlanId
LOSPKTTH lostPacketThreshold
ALRMPERT alarmPersistencyTime
ALRMCLET alarmClearanceTime
NTWTYPC networkTypeCompensation
PNGF pingFrequency
PNGPKT pingPacketSize
System Responses:Operation Completed
After command execution, a message of Changed Configuration Notification is dis-played. A further message indicates the result of the operation. An example of cestunnel command is the following:
JOB:59
PC Time&Date: 09.10.2008 09:46:28 +02:00
NE Time&Date: 01.01.1990 00:08:37 +00:00
CREATE CESTUNNEL NAME=CESTUNNEL:0..0 ,LOCALADDR= ,PEERADDR= [,VLANID=] [,LOSPKTTH=] [,ALRMPERT=] [,ALRMCLET=] [,NTWTYPC=] [,PNGF=] [,PNGPKT=];
DN0933412 Issue 01189
BTSplus mainline commands at the Flexi BSC product family
CESTUNNEL
Id:0900d805805b0cc4
USER NAME: NSN
COMMAND: Create CESTUNNEL:NAME=CESTUNNEL:0,LOCALADDR="
192.168.3.23",PEERADDR="192.168.3.25",VLANID=<NULL>;
SW RELEASE: 03-04-19-06-11-06_08-10-08
COMMAND RESULT:Operation successful
localAddress = "192.168.3.23"
peerAddress = "192.168.3.25"
vlanId = Null
END OF OUTPUT FOR JOB 59
Operation Failed
None.
Application Guidelines:None.
Example of Command Execution:Create CESPW:NAME=CESPW:0,LOCLUDP=49200,MAXPDV=16,PEERUDPPORT= 49200,PKTLAT=m1000,PWNAME="trial1",TDMAP=0-0-0-0-0-0-0-0-0-0-0-0-0-0-0-0-0-0-0-0-0-0-0-0-0-0-0-0-0-0-0;
DELETE CESTUNNEL
Command Tree:“MANAGED-ELEMENT h BSS-EQUIPMENT h BTSEP h CESTUNNEL h DELETE CESTUNNEL”
Applicability:Phase 2.
Visibility level: 2.
Command Description:This command deletes the CESTUNNEL from the BTSE data base.
Long Names:NAME Address of the managed object
System Responses:Operation Completed.
After command execution, a message of Changed Configuration Notification is dis-played. A further message indicates the result of the operation. An example of delete command is the following
JOB: 48
PC Time&Date: 09.10.2008 09:49:00 +02:00
NE Time&Date: 01.01.1990 00:11:09 +00:00
DELETE CESTUNNEL NAME=CESTUNNEL:0..0;
190DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805b0cc4
CESTUNNEL
USER NAME: NSN
COMMAND: Delete CESTUNNEL:NAME=CESTUNNEL:0;
SW RELEASE: 03-04-19-06-11-06_08-10-08
COMMAND RESULT:Operation successful
END OF OUTPUT FOR JOB 48
Operation Failed.
None.
Application Guidelines:
• CESTUNNEL deletion is rejected if a CESPW object exists
Example of Command Execution:Delete CESTUNNEL:NAME=CESTUNNEL:0;
GET CESTUNNEL
Command Tree:“MANAGED-ELEMENT h BSS-EQUIPMENT h BTSEP h CESTUNNEL h GET CESTUNNEL”
Applicability:Phase 2 and Phase 3.
Visibility level: 0.
Command Description:This command displays the attributes of the CESTUNNEL.
Long Names:NAME Address of the managed object
REQATTL Required attribute list
ALS alarmStatus
AST administrativeState
AVS availabilityStatus
OST operationalState
PRS proceduralStatus
RELFUNCOBJ relatedFuncObjects
LOCALADDR localAddress
PEERADDR peerAddress
VLANID vlanId
LOSPKTTH lostPacketThreshold
GET CESTUNNEL NAME=CESTUNNEL:0..0 [,REQATTL=ALS, AST, AVS, OST, PRS, RELFUNCOBJ, LOCALADDR, PEERADDR, VLANID, LOSPKTTH, ALRMPERT, ALRMCLET, NTWTYPC, PNGF, PNGPKT];
DN0933412 Issue 01191
BTSplus mainline commands at the Flexi BSC product family
CESTUNNEL
Id:0900d805805b0cc4
ALRMPERT alarmPersistencyTime
ALRMCLET alarmClearanceTime
NTWTYPC networkTypeCompensation
PNGF pingFrequency
PNGPKT pingPacketSize
System Responses:Operation Completed.
A message indicates the result of the operation. An example of get command is the fol-lowing:
JOB: 75
PC Time&Date: 09.03.2009 09:46:36 +02:00
NE Time&Date: 01.01.1990 00:08:45 +00:00
USER NAME: NSN
COMMAND: Get CESTUNNEL:NAME=CESTUNNEL:0;
SW RELEASE: 03-04-19-06-11-06_08-10-08
COMMAND RESULT:Operation successful
alarmStatus = CLEARED
administrativeState = Unlocked
availabilityStatus = NULL
operationalState = ENABLED
proceduralStatus = NULL
relatedFuncObjects = Null
localAddress = "192.168.3.23"
peerAddress = "192.168.3.25"
vlanId = Null
lostPacketThreshold = 1
alarmPersistencyTime = 3
alarmClearanceTime = 10
networkTypeCompensation = 0
pingFrequency = 0
pingPacketSize = TRAFFIC
END OF OUTPUT FOR JOB 75
Operation Failed
None.
Application Guidelines:None.
Example of Command Execution:Get CESTUNNEL:NAME=CESTUN-NEL:0,REQATTL=ALS&AST&AVS&OST&PRS&RELFUNCOBJ&ALRMCLET&ALRM-
192DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805b0cc4
CESTUNNEL
PERT&LOCALADDR&LOSPKTTH&NTWTYPC&PEERADDR&PNGF&PNGPKT&VLANID;
LOCK CESTUNNEL
Command Tree:“MANAGED-ELEMENT h BSS-EQUIPMENT h BTSEP h CESTUNNEL h LOCK CESTUNNEL”
Applicability:Phase 2.
Visibility level: 1.
Command Description:This command changes the administrative state of CESPW object.
Long Names:NAME Address of the managed object
System Responses:Operation Completed.
The specified change of administrative state has been performed. An example of lock command is the following:
JOB: 39
PC Time&Date: 09.10.2008 09:46:42 +02:00
NE Time&Date: 01.01.1990 00:08:51 +00:00
USER NAME: NSN
COMMAND: Lock CESTUNNEL:NAME=CESTUNNEL:0;
SW RELEASE: 03-04-19-06-11-06_08-10-08
COMMAND RESULT:Operation successful
administrativeState = Locked
END OF OUTPUT FOR JOB 39
Operation Failed.
None.
Application Guidelines:None.
Example of Command Execution:Lock CESPW:NAME=CESPW:0;
LOCK CESTUNNEL NAME=CESTUNNEL:0..0;
DN0933412 Issue 01193
BTSplus mainline commands at the Flexi BSC product family
CESTUNNEL
Id:0900d805805b0cc4
SET CESTUNNEL
Command Tree:“MANAGED-ELEMENT h BSS-EQUIPMENT h BTSEP h CESTUNNEL h SET CESTUNNEL”
Applicability:Phase 2 and Phase 3.
Visibility level: 2.
Command Description:This command sets the attributes of CESTUNNEL object.
Long Names:NAME Address of the managed object
LOCALADDR localAddress
PEERADDR peerAddress
VLANID vlanId
LOSPKTTH lostPacketThreshold
ALRMPERT alarmPersistencyTime
ALRMCLET alarmClearanceTime
NTWTYPC networkTypeCompensation
PNGF pingFrequency
PNGPKT pingPacketSize
System Responses:Operation Completed.
After command execution, a message of Changed Attribute Event Report is displayed. A further message indicates the result of the operation. An example of set command is the following:
JOB: 77
PC Time&Date: 09.10.2009 09:47:56 +02:00
NE Time&Date: 01.01.1990 00:10:05 +00:00
USER NAME: NSN
COMMAND: Set CESTUNNEL:NAME=CESTUNNEL:0,ALRMCLET=4,ALRMPERT=
5,LOSPKTTH=55,PNGF=12,PNGPKT=SMALL,VLANID=02;
SW RELEASE: 03-04-19-06-11-06_08-10-08
COMMAND RESULT:Operation successful
vlanId = 2
lostPacketThreshold = 55
SET CESTUNNEL NAME=CESTUNNEL:0..0 [,LOCALADDR=] [,PEERADDR=] [,VLANID=] [,LOSPKTTH=] [,ALRMPERT=] [,ALRMCLET=] [,NTWTYPC=] [,PNGF=] [,PNGPKT=];
194DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805b0cc4
CESTUNNEL
alarmPersistencyTime = 5
alarmClearanceTime = 4
pingFrequency = 12
pingPacketSize = SMALLEND OF OUTPUT FOR JOB 77
Operation Failed.
None.
Application Guidelines:None.
Example of Command Execution:Set CESTUNNEL:NAME=CESTUNNEL:0,ALRMCLET=4,ALPERT=5,LOSPKTTH= 55,PNGF=12,PNGPKT=SMALL,VLANID=02;?
UNLOCK CESTUNNEL
Command Tree:“MANAGED-ELEMENT h BSS-EQUIPMENT h BTSEP h CESTUNNEL h UNLOCK CESTUNNEL”
Applicability:Phase 2.
Visibility level: 1.
Command Description:This command changes the administrative state of CESTUNNEL object.
Long Names:NAME Address of the managed object
System Responses:Operation Completed.
The specified change of administrative state has been perfomed. An example of unlock command is the following:
JOB: 47
PC Time&Date: 09.10.2008 09:49:48 +02:00
NE Time&Date: 01.01.1990 00:11:57 +00:00
USER NAME: NSN
COMMAND: Unlock CESTUNNEL:NAME=CESTUNNEL:0;
SW RELEASE: 03-04-19-06-11-06_08-10-08
COMMAND RESULT:Operation successful
END OF OUTPUT FOR JOB 47
administrativeState = Unlocked
Operation Failed
UNLOCK CESTUNNEL NAME=CESTUNNEL:0..0;
DN0933412 Issue 01195
BTSplus mainline commands at the Flexi BSC product family
CESTUNNEL
Id:0900d805805b0cc4
None.
Application Guidelines:None.
Example of Command Execution:Unlock CESTUNNEL:NAME=RACK:0/CESTUNNEL:0
196DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805b0cc6
CHAN
CHANThe CHAN object represents the radio time slot in which the radio carrier is subdivided into time sharing; it can be differently configured depending on its usage for the tele-phone application software (full rate or half rate traffic channels, dedicated or common control channels).
GET CHAN
Command Tree:“MANAGED-ELEMENT h BSS-FUNCTIONAL h BTSM h BTS h TRX h CHAN h GET CHAN”
Applicability:Phase 3.
Visibility level: 0.
Command Description:This command displays the physical radio channel with its specific attributes which allows logical channels to be mapped onto physical radio channels.
Long Names:NAME Address of the managed object
REQATTL Required attribute list
ABISCH abisChannel
AST administrativeState
AVS availabilityStatus
CHTYPE channelCombination
EXTMODE extendedMode
HSN hoppingSequenceNumber
MAIO maio
MOBALLOC arfcnList
OST operationalState
RELEQUIPOBJ relatedEquipObjects
TSC trainingSequenceCode
System Responses:Operation Completed.
After command execution, a message of Changed Configuration Notification is dis-played. A further message indicates the result of the operation. An example of get command is the following:
GET CHAN NAME=BTS:0..11/TRX:0..23/CHAN:0..7 [,REQATTL=ABISCH, AST, AVS, CHTYPE, EXTMODE, HSN, MAIO, MOBALLOC, OST, RELEQUIPOBJ, TSC];
DN0933412 Issue 01197
BTSplus mainline commands at the Flexi BSC product family
CHAN
Id:0900d805805b0cc6
JOB: 17
PC Time&Date: 11:33:17 03/23/2005
NE Time&Date: 11:31:08 09/15/2004
USER NAME: NSN
COMMAND: Get CHAN:NAME=BTS:0/TRX:0/CHAN:0;
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: Operation successful
administrativeState = Unlocked
availabilityStatus = NULL
channelCombination = MAINBCCH
extendedMode = FALSE
hoppingSequenceNumber = 0
maio = 0
arfcnList =
operationalState = ENABLED
relatedEquipObjects =
trainingSequenceCode = TSC_is_BCC_of_BSIC
END OF OUTPUT FOR JOB 17
Operation Failed
The GET command has not been successfully executed. A general NACK will indicate possible errors or a specific NACK strictly related to the single command is possible.
Application Guidelines:None.
Example of Command Execution:Get CHAN:NAME=BTS:0/TRX:0/CHAN:0,REQATTL=AST&AVS&CHTYPE&
EXTMODE&HSN&MAIO&MOBALLOC&OST&RELEQUIPOBJ&TSC;
198DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805b0cc8
COBA
COBAThe COBA module controls the entire BTSplus mainline, generates the system clocks, provides for up to 2 Abis-interfaces to the Flexi BSC product family or other BTSplus mainlines, routes the Abis-data to up to 8 Carrier Agents, provides for an interface to the LMT Evolution/OTP, handles and processes the O&M-messages.
CREATE COBA
Command Tree:“MANAGED-ELEMENT h BSS-EQUIPMENT h BTSEP h RACK h COBA h CREATE COBA”
Applicability:Phase 2 and Phase 3.
Visibility level: 2.
Command Description:This command displays the attributes of the COBA (Core Basis module).
Long Names:NAME Address of the managed object
ALRMCOUNTER alarmCount
ALRMT1/2/3 alarmTiming1(sec)/2/3
EFCUSUP enableFcuSupport
System Responses:Operation Completed
After command execution, a message of Changed Configuration Notification is dis-played. A further message indicates the result of the operation. An example of create command is the following:
JOB: 158
PC Time&Date: 16:45:36 03/23/2005
NE Time&Date: 16:43:30 09/15/2004
USER NAME: NSN
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: Operation successful
ChangedConfigurationNotification:
CREATE COBA NAME=RACK:0..7/COBA:0..1 [,ALRMCOUNTER=] [,ALRMT1/2/3=] [,EFCUSUP=];
DN0933412 Issue 01199
BTSplus mainline commands at the Flexi BSC product family
COBA
Id:0900d805805b0cc8
name = RACK:0/COBA:1
ChangeInfo = created
END OF OUTPUT FOR JOB 158
JOB: 159
PC Time&Date: 16:45:36 03/23/2005
NE Time&Date: 16:43:30 09/15/2004
USER NAME: NSN
COMMAND: Create COBA:NAME=RACK:0/COBA:1;
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: Operation successful
END OF OUTPUT FOR JOB 159
Operation Failed
The specified Object has not been created. In addition to the general NACK causes, a specific NACK cause, which indicates that the command is inconsistent with the physical configuration, is possible. An example is the following:
JOB: 71
PC Time&Date: 16:37:54 03/23/2005
NE Time&Date: 16:35:47 09/15/2004
USER NAME: NSN
COMMAND: Create COBA:NAME=RACK:0/COBA:1;
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: OPERATION FAILED
Object instance unknown (-9)
END OF OUTPUT FOR JOB 71
Application Guidelines:
• Only COBA:1 can be created
200DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805b0cc8
COBA
Example of Command Execution:Create COBA:NAME=RACK:0/COBA:1,ALRMCOUNTER=234,ALRMT1=23,
ALRMT2=34,ALRMT3=45, EFCUSUP=TRUE;
DELETE COBA
Command Tree:“MANAGED-ELEMENT h BSS-EQUIPMENT h BTSEP h RACK h COBA h DELETE COBA”
Applicability:Phase 2 and Phase 3.
Visibility level: 2.
Command Description:This command displays the attributes of the COBA (Core Basis module).
Long Names:NAME Address of the managed object
System Responses:Operation Completed
After command execution, a message of Changed Configuration Notification is dis-played. A further message indicates the result of the operation. An example of delete command is the following:
JOB: 182
PC Time&Date: 16:48:02 03/23/2005
NE Time&Date: 16:45:56 09/15/2004
USER NAME: NSN
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: Operation successful
ChangedConfigurationNotification:
name = RACK:0/COBA:1
ChangeInfo = deleted
END OF OUTPUT FOR JOB 182
JOB: 183
DELETE COBA NAME=RACK:0..7/COBA:0..1;
DN0933412 Issue 01201
BTSplus mainline commands at the Flexi BSC product family
COBA
Id:0900d805805b0cc8
PC Time&Date: 16:48:02 03/23/2005
NE Time&Date: 16:45:56 09/15/2004
USER NAME: NSN
COMMAND: Delete COBA:NAME=RACK:0/COBA:1;
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: Operation successful
END OF OUTPUT FOR JOB 183
Operation Failed
The specified Object has not been deleted. Additionally to the general NACK causes, a specific NACK cause, meaning that the command is inconsistent with physical configu-ration, is possible.
Application Guidelines:
• Only COBA:1 can be deleted
• COBA:1 must be locked in Phase 3 before deletion
Example of Command Execution:Delete COBA:NAME=RACK:0/COBA:1;
GET COBA
Command Tree:“MANAGED-ELEMENT h BSS-EQUIPMENT h BTSEP h RACK h COBA h GET COBA”
Applicability:Phase 2 and Phase 3.
Visibility level: 0.
Command Description:This command displays the attributes of the COBA (Core Basis module).
Long Names:NAME Address of the managed object
REQATTL Required attribute list
ALRMCOUNTER alarmCount
ALRMT1/2/3 alarmTiming1(sec)/2/3
GET COBA NAME=RACK:0..7/COBA:0..1 [,REQATTL=ALRMCOUN-TER, ALRMT1/2/3, ALS, AST, AVS, BCPBL, BSWVER, EFCUSUP, OST, PRS, RELFUNCOBJ, SLOTNO, STD-BYST];
202DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805b0cc8
COBA
ALS alarmStatus
AST administrativeState
AVS availabilityStatus
BCPBL boardCapability
BSWVER bootSoftwareVersion
EFCUSUP enableFcuSupport
OST operationalState
PRS proceduralStatus
RELFUNCOBJ relatedFuncObjects
SLOTNO slotNo
STDBYST standbyStatus
System Responses:Operation Completed
After command execution, a message of Changed Configuration Notification is dis-played. A further message indicates the result of the operation. An example of get command is the following:
JOB: 163
USER NAME: NSN
COMMAND: Get COBA:NAME=RACK:0/COBA:0;
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: Operation successful
acPeriod = 20
alarmCount = 32
alarmTiming1(sec) = 20
alarmTiming2(sec) = 1
alarmTiming3(*5min) = 1
alarmStatus = CLEARED
administrativeState = Unlocked
availabilityStatus = NULL
boardCapability = twoAbisLines
bootSoftwareVersion = "BTBBCX01.SWI:01-01-11-00-18-00_04-06-13"
enableFcuSupport = FALSE
operationalState = ENABLED
proceduralStatus = NULL
slotNo = leftCOBA
standbyStatus = ProvidingService
DN0933412 Issue 01203
BTSplus mainline commands at the Flexi BSC product family
COBA
Id:0900d805805b0cc8
END OF OUTPUT FOR JOB 163
Operation Failed
The GET command has not been successfully executed. A general NACK will indicate possible errors or a specific NACK strictly related to the single command is possible.
Application Guidelines:
• COBA:0 is the one with "Providing Service" Status, COBA:1 is in Standby Status
Example of Command Execution:Get COBA:NAME=RACK:0/COBA:0,REQATTL=ACPER&ALRMCOUNTER&
ALRMT1& ALRMT2&ALRMT3&ALS&AST&AVS&BCPBL&BSWVER&CCLKACC&
EFCUSUP&OST&PRS&SLOTNO&STDBYST;
GETRELATIONSHIP COBA
Command Tree:“MANAGED-ELEMENT h BSS-EQUIPMENT h BTSEP h RACK h COBA h GETRELATIONSHIP COBA”
Applicability:Phase 2 and Phase 3.
Visibility level: 0.
Command Description:This command displays the attributes of the COBA (Core Basis module).
Long Names:NAME Address of the managed object
REQATTL Required attribute list
System Responses:Operation Completed
After command execution, a message of Changed Configuration Notification is dis-played. A further message indicates the result of the operation. An example of getrela-tionship command is the following:
JOB: 164
PC Time&Date: 15:08:34 03/23/2005
NE Time&Date: 16:11:29 09/15/2004
GETRELATIONSHIP COBA
NAME=RACK:0..7/COBA:0..1;
204DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805b0cc8
COBA
USER NAME: NSN
COMMAND: Getrelationship COBA:NAME=RACK:0/COBA:0;
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: Operation successful
END OF OUTPUT FOR JOB 164
Operation Failed
The GET command has not been successfully executed. A general NACK will indicate possible errors or a specific NACK strictly related to the single command is possible.
Application Guidelines:None.
Example of Command Execution:Getrelationship COBA:NAME=RACK:0/COBA:0;
GETTEST COBA
Command Tree:“MANAGED-ELEMENT h BSS-EQUIPMENT h BTSEP h RACK h COBA h GETTEST COBA”
Applicability:Phase 2 and Phase 3.
Visibility level: 0.
Command Description:This command displays the attributes of the COBA test.
Long Names:NAME Address of the managed object
REQATTL Required attribute list
System Responses:Operation Completed
After command execution, a message of Changed Configuration Notification is dis-played. A further message indicates the result of the operation. An example of gettest command is the following:
JOB: 187
PC Time&Date: 12:07:21 03/23/2005
NE Time&Date: 13:08:54 09/15/2004
GETTEST COBA NAME=RACK:0..7/COBA:0..1;
DN0933412 Issue 01205
BTSplus mainline commands at the Flexi BSC product family
COBA
Id:0900d805805b0cc8
USER NAME: NSN
COMMAND: Gettest COBA:NAME=RACK:0/COBA:0;
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: Operation successful
MOT = RACK:0/COBA:0
testMonitor =
phaseId = PreliminaryTestsCoba
phaseStatus = Running
phaseId = CheckAlarmStatusCoba
phaseStatus = Waiting
phaseId = EndTestCoba
phaseStatus = Waiting
testOutcome = INCONCLUSIVE
testState = INITIALIZING
END OF OUTPUT FOR JOB 187
Operation Failed
The GET command has not been successfully executed. A general NACK will indicate possible errors or a specific NACK strictly related to the single command is possible.
Application Guidelines:None.
testMonitor it is a list of all test phases related to the selected object; for each phase the related phaseStatus is provided (Passed, Failed, Running or Waiting).
phaseId =
phaseStatus =
phaseId =
phaseStatus =
...
...
testOutcome It represents the test result: it can be Inconclusive (if the phases already executed were successful) or Fail (if at least one of the executed phases failed).
testState = Testing It can assume one of the following values: not_initialized, idle, initializing, sus-pended, testing, terminating and dis-abled.
206DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805b0cc8
COBA
Example of Command Execution:Gettest COBA:NAME=RACK:0/COBA:0, REQATTL=MORT&TESTMON&
TESTOUT&TESTST;
LOCK COBA
Command Tree:“MANAGED-ELEMENT h BSS-EQUIPMENT h BTSEP h RACK h COBA h LOCK COBA”
Applicability:Phase 2 and Phase 3.
Visibility level: 1.
Command Description:This command changes the administrative state of the COBA (Core Basis module).
Long Names:NAME Address of the managed object
System Responses:Operation Completed
The specified change of administrative state has been perfomed. An example of lock command is the following:
JOB: 166
PC Time&Date: 16:46:53 03/23/2005
NE Time&Date: 16:44:47 09/15/2004
USER NAME: NSN
COMMAND: Lock COBA:NAME=RACK:0/COBA:1;
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: Operation successful
administrativeState = Locked
END OF OUTPUT FOR JOB 166
CHANGED STATE EVENT REPORT:
This provides information about the administrative state, the operational state and the availability status every time a state change occurs:
LOCK COBA NAME=RACK:0..7/COBA:0..1;
DN0933412 Issue 01207
BTSplus mainline commands at the Flexi BSC product family
COBA
Id:0900d805805b0cc8
JOB: 167
PC Time&Date: 16:46:53 03/23/2005
NE Time&Date: 16:44:47 09/15/2004
USER NAME: NSN
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: Operation successful
CHANGED STATE EVENT REPORT:
NAME = RACK:0/COBA:1
Administrative State = LOCKED
Notification Identifier = 551
END OF OUTPUT FOR JOB 167
Operation Failed
The specified change of administrative state has not been performed.
Application Guidelines:
• Lock COBA:0 only in Phase 2
Example of Command Execution:Lock COBA:NAME=RACK:0/COBA:0;
PERFTEST COBA
Command Tree:“MANAGED-ELEMENT h BSS-EQUIPMENT h BTSEP h RACK h COBA h PERFTEST COBA”
Applicability:Phase 2 and Phase 3.
Visibility level: 1.
Command Description:This command is used to start an asynchronous test in COBA.
Long Names:NAME Address of the managed object
System Responses:Operation Completed
PERFTEST COBA NAME=RACK:0..7/COBA:0..1;
208DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805b0cc8
COBA
Test configuration has been set and the specified test has been started. The System response will not be addressed to the MOT but to the object BTSEP. An example of perftest command is the following:
JOB: 188
PC Time&Date: 12:06:51 03/23/2009
NE Time&Date: 13:08:26 09/15/2009
USER NAME: NSN
COMMAND: Perftest COBA:NAME=RACK:0/COBA:0;
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: Operation successful
MOT = RACK:0/COBA:0
tO = BTSETEST:2
END OF OUTPUT FOR JOB 188
JOB: 189
PC Time&Date: 12:07:23 03/23/2009
NE Time&Date: 13:08:53 09/15/2009
USER NAME: NSN
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: Operation successful
ChangedConfigurationNotification:
name = BTSETEST:2
ChangeInfo = created
END OF OUTPUT FOR JOB 189
JOB: 190
PC Time&Date: 12:07:38 03/23/2009
NE Time&Date: 13:09:02 09/15/2009
DN0933412 Issue 01209
BTSplus mainline commands at the Flexi BSC product family
COBA
Id:0900d805805b0cc8
USER NAME: NSN
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: Operation successful
CHANGED STATE EVENT REPORT:
NAME = RACK:0/COBA:0
Operational State = ENABLED
Availability Status = NULL_value
Standby Status = Cold_Standby
Notification Identifier = 164
END OF OUTPUT FOR JOB 190
JOB: 191
PC Time&Date: 12:07:52 03/23/2005
NE Time&Date: 13:09:34 09/15/2004
USER NAME: NSN
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: Operation successful
Test Report:
name = BTSETEST:2
testOutcome = PASSED
testTermination = Normal
MOT = RACK:0/COBA:0
executedPhases =
PreliminaryTestsCoba
BootEepromTestCoba
SerialEepromTestCoba
EndTestCoba
END OF OUTPUT FOR JOB 191
JOB: 192
210DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805b0cc8
COBA
PC Time&Date: 12:08:04 03/23/2005
NE Time&Date: 13:09:28 09/15/2004
USER NAME: NSN
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: Operation successful
ChangedConfigurationNotification:
name = BTSETEST:2
ChangeInfo = deleted
END OF OUTPUT FOR JOB 192
The test results will be displayed at the end of the test phases.
Result TEST:
name = TEST:<n>
testOutcome = This field represents the test result; one of the fol-lowing values can be displayed:
Pass all the test phases are successfully performed.
Inconclusive the test is aborted by the system or the test is terminated by the opera-tor.
Fail if at least one of the executed phases fail.
mOts = It is the identifier of the hardware object under test.
testTermination = It specifies how the test is terminated, it can assume the following values:
Normal all the test phases are performed.
Abort the test is aborted by system.
Cancel the test is terminated by operator.
executedPhases
phaseId = It represents the list of the executed test phases (in case of successful test result, all the test phases will be listed).
additionalWords =
....
failedPhases
phaseId = It represents the list of the failed test phase; addi-tional information is provided for each phase.phaseId =
DN0933412 Issue 01211
BTSplus mainline commands at the Flexi BSC product family
COBA
Id:0900d805805b0cc8
Operation Failed
This NACK-message occurs in the following cases: Message cannot be performed, test not supported, capacity restrictions, physical configuration cannot be performed, object not locked.
Application Guidelines:
• In phase 3 COBA must be locked previous to the command
• Perftest for COBA:0 in phase 2 only
Example of Command Execution:Perftest COBA:NAME=RACK:0/COBA:0;
SET COBA
Command Tree:“MANAGED-ELEMENT h BSS-EQUIPMENT h BTSEP h RACK h COBA h SET COBA”
Applicability:Phase 2 and Phase 3.
Visibility level: 2.
Command Description:This command permits modification of the attributes of the COBA (Core Basis module).
Long Names:NAME Address of the managed object
ALRMCOUNTER alarmCount
ALRMT1/2/3 alarmTiming1(sec)/2/3
EFCUSUP enableFcuSupport
System Responses:Operation Completed
....
skippedPhases
phaseId = It represents the list of the skipped phases; they are displayed only for test stopped during it execution.phaseId =
....
poprosedRepair Action =
A list of most probable fail probable causes is shown (max four messages)
SET COBA NAME=RACK:0..7/COBA:0..1 [,ALRMCOUNTER=] [,ALRMT1/2/3=] [,EFCUSUP=];
212DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805b0cc8
COBA
After command execution, a message of Changed Attribute Event Report is displayed. A further message indicates the result of the operation. An example of set command is the following:
JOB: 172
PC Time&Date: 16:47:25 03/23/2005
NE Time&Date: 16:45:19 09/15/2004
USER NAME: NSN
COMMAND: Set COBA:NAME=RACK:0/COBA:1;
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: Operation successful
END OF OUTPUT FOR JOB 172
Operation Failed
The specified attributes have not been set. In addition to the general NACK causes, a specific NACK cause, which indicates that the command is inconsistent with the physical configuration, is possible.
Application Guidelines:
• The alarm evaluation on BTSE for the layer 1 is based on an "Errored Second" concept. I.e.: If an error is found active (counted every 2 msec.) for x times (x = 5 for "No signal", "AIS", "Loss of frame alignment ...) within 1 second, the whole second is declared faulty otherwise the second is declared as "good". If one "Errored Second" is detected, the subsequent seconds will be also declared faulty until no error is detected within one second. This means that the layer 1 alarm handling is very sensitive. With the default setting of "ALRMT2" which is 1 second a short inter-ruption of 10 msec will cause an alarm generated by the BTSE. In order to increase the tolerance of the BTSE layer 1 alarm handling against short interruptions on the lines, the operator can change the value of the timer "ALRMT2" from the default setting (1 second) to a higher value (e.g. 2 seconds). Nevertheless if the BTSE gen-erates a layer 1 alarm no further actions are performed. Call processing is not inhib-ited as long as the layer 2 is up or the Flexi BSC product family does not declare the line disabled
Example of Command Execution:Set COBA:NAME=RACK:0/COBA:0,ACPER=20&ALRMCOUNTER=32,ALRMT1=20,
ALRMT2=2,ALRMT3=1,EFCUSUP=TRUE;
STOPTEST COBASTOPTEST COBA NAME=RACK:0..7/COBA:0..1;
DN0933412 Issue 01213
BTSplus mainline commands at the Flexi BSC product family
COBA
Id:0900d805805b0cc8
Command Tree:“MANAGED-ELEMENT h BSS-EQUIPMENT h BTSEP h RACK h COBA h STOPTEST COBA”
Applicability:Phase 2 and Phase 3.
Visibility level: 1.
Command Description:This command is used to stop a diagnostic previously started.
Long Names:NAME Address of the managed object
System Responses:Operation Completed
Test has been stopped. The System Responses will not be addressed to the MOT but to the object BTSEP.
Operation Failed
Test has not been stopped. This NACK-message can occur when the specified test is not running or in case of test which cannot be stopped.
Application Guidelines:None.
Result TEST:
name = TEST:<n>
testOutcome = inconclusive
mOts = It is the identifier of the hardware object under test.
testTermination = Cancel
executedPhases
phaseId = It represents the list of the executed test phases; the list is not shown for test in the waiting list (queued)....
.
failedPhases
phaseId = It represents the list of the failed test phase;
additional information is provided for each phase.phaseId =
....
skippedPhases
phaseId = It represents the list of the skipped phases;the list is not shown for test in the waiting list (queued).phaseId =
214DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805b0cc8
COBA
Example of Command Execution:Stoptest COBA:NAME=RACK:0/COBA:0;
SWITCH COBA
Command Tree:“MANAGED-ELEMENT h BSS-EQUIPMENT h BTSEP h RACK h COBA h SWITCH COBA”
Applicability:Phase 2 and Phase 3.
Visibility level: 1.
Command Description:This command is used to switch to the standby copy of COBA.
Long Names:NAME Address of the managed object
System Responses:Operation Completed. An example of switch command is the following:
JOB: 60
PC Time&Date: 11:57:24 03/23/2005
NE Time&Date: 12:58:59 09/15/2004
USER NAME: NSN
COMMAND: Switch COBA:NAME=RACK:0/COBA:0;
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: Operation successful
END OF OUTPUT FOR JOB 60
Operation Failed
JOB: 61
PC Time&Date: 11:57:31 03/23/2005
NE Time&Date: 12:59:06 09/15/2004
USER NAME: NSN
COMMAND: Switch COBA:NAME=RACK:0/COBA:0;
SW RELEASE: 01-04-17-01-26-51_05-02-23
SWITCH COBA NAME=RACK:0..7/COBA:0..1;
DN0933412 Issue 01215
BTSplus mainline commands at the Flexi BSC product family
COBA
Id:0900d805805b0cc8
COMMAND RESULT: OPERATION FAILED
no redundant core board available (-173)
END OF OUTPUT FOR JOB 61
Application Guidelines:
• Only COBA:0 can be switched
• No redundancy present in BS82II (the command is not applicable)
Example of Command Execution:Switch COBA:NAME=RACK:0/COBA:0;
UNLOCK COBA
Command Tree:“MANAGED-ELEMENT h BSS-EQUIPMENT h BTSEP h RACK h COBA h UNLOCK COBA”
Applicability:Phase 2 and Phase 3.
Visibility level: 1.
Command Description:This command changes the administrative state of the COBA (Core Basis module).
Long Names:NAME Address of the managed object
System Responses:Operation Completed
The specified change of administrative state has been perfomed. An example of unlock command is the following:
JOB: 173
PC Time&Date: 16:47:33 03/23/2005
NE Time&Date: 16:45:27 09/15/2004
USER NAME: NSN
COMMAND: Unlock COBA:NAME=RACK:0/COBA:1;
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: Operation successful
UNLOCK COBA NAME=RACK:0..7/COBA:0..1;
216DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805b0cc8
COBA
administrativeState = Unlocked
END OF OUTPUT FOR JOB 173
CHANGED STATE EVENT REPORT:
This provides information about the administrative state, the operational state and the availability status every time a state change occurs:
JOB: 174
PC Time&Date: 16:47:33 03/23/2005
NE Time&Date: 16:45:27 09/15/2004
USER NAME: NSN
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: Operation successful
CHANGED STATE EVENT REPORT:
NAME = RACK:0/COBA:1
Administrative State = UNLOCKED
Notification Identifier = 556
END OF OUTPUT FOR JOB 174
Operation Failed
The specified change of administrative state has not been performed.
Application Guidelines:
• Unlock COBA:0 only in phase 2
Example of Command Execution:Unlock COBA:NAME=RACK:0/COBA:0;
DN0933412 Issue 01217
BTSplus mainline commands at the Flexi BSC product family
COBAETHINTF
Id:0900d805805b0cca
COBAETHINTFThis object represents the Ethernet interface of the new COBA which is connected to the Zarlink device. It is introduced to configure/retrieve Ethernet interface specific infor-mation (similar to UNIX eth<x>) and to indicate state information.
The object is automatically created if a new COBA with CES support is equipped.
GET COBAETHINTF
Command Tree:“MANAGED-ELEMENT h BSS-EQUIPMENT h BTSEP h COBAETHINTF h GET COBAETHINTF”
Applicability:Phase 2 and Phase 3.
Visibility level: 0.
Command Description:This command displays the attributes of the COBAETHINTF.
Long Names:NAME Address of the managed object
REQATTL Required attribute list
ALS alarmStatus
AST administrativeState
AVS availabilityStatus
OST operationalState
PRS proceduralStatus
RELFUNCOBJ relatedFuncObjects
MACADDR macAddress
TYPOFETH typeOfEthernet
System Responses:Operation Completed.
A mesNSNe indicates the result of the operation. An example of get command is the fol-lowing:
JOB: 65
PC Time&Date: 02.04.2008 09:11:51 +02:00
NE Time&Date: 01.01.1990 18:27:29 +00:00.
COMMAND: Get COBAETHINTF:NAME=COBAETHINTF:0;
SW RELEASE: 01-04-19-01-08-CR_08-03-31
COMMAND RESULT:Operation successfulalarmStatus = CLEARED
GET COBAETHINTF NAME=COBAETHINTF:0..0 [,REQATTL=ALS, AST, AVS, OST, PRS, RELFUNCOBJ, MACADDR, TYPOFETH];
218DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805b0cca
COBAETHINTF
administrativeState = Unlocked
availabilityStatus = NULL
operationalState = ENABLED
proceduralStatus = NULL
macAddress = "08:00:06:78:64:63"
typeOfEthernet = ethernet_II
END OF OUTPUT FOR JOB 65
Operation Failed
None.
Application Guidelines:None.
Example of Command Execution:Get COBAETHINTF:NAME=COBAETHINTF:0, REQATTL=ALS&AST&AVS&OST&PRS&RELFUNCOBJ&MACADR&TETH;
LOCK COBAETHINTF
Command Tree:“MANAGED-ELEMENT h BSS-EQUIPMENT h BTSEP h COBAETHINTF h LOCK COBAETHINTF”
Applicability:Phase 2.
Visibility level: 1.
Command Description:This command changes the administrative state of COBAETHINTF.
Long Names:NAME Address of the managed object
System Responses:Operation Completed
The specified change of administrative state has been perfomed:
JOB: 89
PC Time&Date: 05.06.2008 13:18:01 +02:00
NE Time&Date: 01.01.1990 00:14:45 +00:00
USER NAME: NSN
COMMAND: Lock COBAETHINTF:NAME=COBAETHINTF:0;
SW RELEASE: 01-04-19-01-09-ZS_08-06-03
COMMAND RESULT:Operation successful
LOCK COBAETHINTF NAME=COBAETHINTF:0..0;
DN0933412 Issue 01219
BTSplus mainline commands at the Flexi BSC product family
COBAETHINTF
Id:0900d805805b0cca
administrativeState = Locked
END OF OUTPUT FOR JOB 89
Operation Failed
None.
Application Guidelines:None.
Example of Command Execution:Lock COBAETHINTF:NAME=COBAETHINTF:0;
SET COBAETHINTF
Command Tree:“MANAGED-ELEMENT h BSS-EQUIPMENT h BTSEP h COBAETHINTF h SET COBAETHINTF”
Applicability:Phase 2.
Visibility level: 2.
Command Description:This command sets the attributes of COBAETHINTF.
Long Names:NAME Address of the managed object
TYPOFETH typeOfEthernet
System Responses:Operation Completed
After command execution, a mesNSNe of Changed Attribute Event Report is displayed. A further mesNSNe indicates the result of the operation.
An example of set command is the following:
JOB: 35
PC Time&Date: 11.02.2008 11:34:29 +01:00
NE Time&Date: 01.01.1990 00:40:35 +00:00
USER NAME: NSN
COMMAND: Set COBAETHINTF:NAME=COBAETHINTF:0,TETH=ethernet_II;
SW RELEASE: 01-04-19-01-01-CR_08-01-11
COMMAND RESULT:Operation successful
typeOfEthernet = ethernet_II
END OF OUTPUT FOR JOB 35
Operation Failed
SET COBAETHINTF NAME=COBAETHINTF:0..0 [,TYPOFETH=];
220DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805b0cca
COBAETHINTF
None.
Application Guidelines:None.
Example of Command Execution:Set COBAETHINTF:NAME=COBAETHINTF:0,TYPOFETH=ethernet_II;
UNLOCK COBAETHINTF
Command Tree:“MANAGED-ELEMENT h BSS-EQUIPMENT h BTSEP h COBAETHINTF h UNLOCK COBAETHINTF”
Applicability:Phase 2.
Visibility level: 1.
Command Description:This command changes the administrative state of COBAETHINTF.
Long Names:NAME Address of the managed object
System Responses:Operation Completed
The specified change of administrative state has been perfomed:
JOB: 98
PC Time&Date: 05.06.2008 13:18:14 +02:00
NE Time&Date: 01.01.1990 00:14:58 +00:00
USER NAME: NSN
COMMAND: Unlock COBAETHINTF:NAME=COBAETHINTF:0;
SW RELEASE: 01-04-19-01-09-ZS_08-06-03
COMMAND RESULT:Operation successful
administrativeState = Unlocked
END OF OUTPUT FOR JOB 98.
Operation Failed
None.
Application Guidelines:None.
Example of Command Execution:Unlock COBAETHINTF:NAME=COBAETHINTF:0;
UNLOCK COBAETHINTF
NAME=COBAETHINTF:0..0;
DN0933412 Issue 01221
BTSplus mainline commands at the Flexi BSC product family
COSA
Id:0900d805805b0ccc
COSAThe COSA (Core Satellite Interface module) object is the core controller expansion unit and it is contained in the base rack only.
CREATE COSA
Command Tree:“MANAGED-ELEMENT h BSS-EQUIPMENT h BTSEP h RACK h COSA h CREATE COSA”
Applicability:Phase 2 and Phase 3.
Visibility level: 2.
Command Description:This command adds the COSA (Core Satellite interface module) to the BTSE data base.
Long Names:NAME Address of the managed object
System Responses:Operation Completed
After command execution, a message of Changed Configuration Notification is dis-played. A further message indicates the result of the operation. An example of create command is the following:
JOB: 146
PC Time&Date: 16:44:39 03/23/2005
NE Time&Date: 16:42:33 09/15/2004
USER NAME: NSN
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: Operation successful
ChangedConfigurationNotification:
name = RACK:0/COSA:1
ChangeInfo = created
END OF OUTPUT FOR JOB 146
CREATE COSA NAME=RACK:0..7/COSA:0..1;
222DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805b0ccc
COSA
JOB: 147
PC Time&Date: 16:44:39 03/23/2005
NE Time&Date: 16:42:33 09/15/2004
USER NAME: NSN
COMMAND: Create COSA:NAME=RACK:0/COSA:1;
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: Operation successful
END OF OUTPUT FOR JOB 147
Operation Failed
The specified Object has not been created. In addition to the general NACK causes, a specific NACK cause, which indicates that the command is inconsistent with the physical configuration, is possible. An example is the following:
JOB: 70
PC Time&Date: 16:37:54 03/23/2005
NE Time&Date: 16:35:47 09/15/2004
USER NAME: NSN
COMMAND: Create COSA:NAME=RACK:0/COSA:1;
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: OPERATION FAILED
Object instance unknown (-9)
END OF OUTPUT FOR JOB 70
Application Guidelines:
• COSA creation is not possible for BS82II
Example of Command Execution:Create COSA:NAME=RACK:0/COSA:0;
DELETE COSADELETE COSA NAME=RACK:0..7/COSA:0..1;
DN0933412 Issue 01223
BTSplus mainline commands at the Flexi BSC product family
COSA
Id:0900d805805b0ccc
Command Tree:“MANAGED-ELEMENT h BSS-EQUIPMENT h BTSEP h RACK h COSA h DELETE COSA”
Applicability:Phase 2 and Phase 3.
Visibility level: 2.
Command Description:This command deletes the COSA (Core Satellite interface module) from the BTSE data base.
Long Names:NAME Address of the managed object
System Responses:Operation Completed
After command execution, a message of Changed Configuration Notification is dis-played. A further message indicates the result of the operation. An example of delete command is the following:
JOB: 156
PC Time&Date: 16:45:32 03/23/2005
NE Time&Date: 16:43:26 09/15/2004
USER NAME: NSN
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: Operation successful
ChangedConfigurationNotification:
name = RACK:0/COSA:1
ChangeInfo = deleted
END OF OUTPUT FOR JOB 156
JOB: 157
PC Time&Date: 16:45:32 03/23/2005
NE Time&Date: 16:43:26 09/15/2004
USER NAME: NSN
224DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805b0ccc
COSA
COMMAND: Delete COSA:NAME=RACK:0/COSA:1;
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: Operation successful
END OF OUTPUT FOR JOB 157
Operation Failed
The specified Object has not been deleted. Additionally to the general NACK causes, a specific NACK cause, meaning that the command is inconsistent with physical configu-ration, is possible.
Application Guidelines:
• COSA must be locked in Phase 3 before deletion
Example of Command Execution:Delete COSA:NAME=RACK:0/COSA:0;
GET COSA
Command Tree:“MANAGED-ELEMENT h BSS-EQUIPMENT h BTSEP h RACK h COSA h GET COSA”
Applicability:Phase 2 and Phase 3.
Visibility level: 0.
Command Description:This command displays the attributes of the COSA (Core Satellite interface module).
Long Names:NAME Address of the managed object
REQATTL Required attribute list
ALS alarmStatus
AST administrativeState
AVS availabilityStatus
OST operationalState
PRS proceduralStatus
RELFUNCOBJ relatedFuncObjects
SLOTNO slotNo
STDBYST standbyStatus
System Responses:Operation Completed
GET COSA NAME=RACK:0..7/COSA:0..1 [,REQATTL=ALS, AST, AVS, OST, PRS, RELFUNCOBJ, SLOTNO, STDBYST];
DN0933412 Issue 01225
BTSplus mainline commands at the Flexi BSC product family
COSA
Id:0900d805805b0ccc
After command execution, a message of Changed Configuration Notification is dis-played. A further message indicates the result of the operation. An example of get command is the following:
JOB: 148
PC Time&Date: 16:45:02 03/23/2005
NE Time&Date: 16:42:56 09/15/2004
USER NAME: NSN
COMMAND: Get COSA:NAME=RACK:0/COSA:1;
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: Operation successful
alarmStatus = CLEARED
administrativeState = Unlocked
availabilityStatus = NotInstalled
operationalState = DISABLED
proceduralStatus = NULL
relatedFuncObjects =
slotNo = leftCOSA
standbyStatus = NULL
END OF OUTPUT FOR JOB 148
Operation Failed
The GET command has not been successfully executed. A general NACK will indicate possible errors or a specific NACK strictly related to the single command is possible.
Application Guidelines:
• COSA:0 is the one with "Providing Service" Status, COSA:1 is in Standby Status
Example of Command Execution:Get COSA:NAME=RACK:0/COSA:0,REQATTL=ALS&AST&AVS&
RELFUNCOBJ&OST& PRS.
GETTEST COSA
Command Tree:“MANAGED-ELEMENT h BSS-EQUIPMENT h BTSEP h RACK h COSA h GETTEST COSA”
GETTEST COSA NAME=RACK:0..7/COSA:0..1;
226DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805b0ccc
COSA
Applicability:Phase 2 and Phase 3.
Visibility level: 0.
Command Description:This command displays the attributes of the COSA test.
Long Names:NAME Address of the managed object
REQATTL Required attribute list
System Responses:Operation Completed
After command execution, a message of Changed Configuration Notification is dis-played. A further message indicates the result of the operation. An example of gettest command is the following:
JOB: 193
PC Time&Date: 12:08:22 03/23/2005
NE Time&Date: 13:09:33 09/15/2004
USER NAME: NSN
COMMAND: Gettest COSA:NAME=RACK:0/COSA:0;
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: Operation successful
MOT = RACK:0/COSA:0
testMonitor =
phaseId = PreliminaryTestsCosa
phaseStatus = Running
phaseId = CheckAlarmStatusCosa
phaseStatus = Waiting
phaseId = EndTestCosa
phaseStatus = Waiting
testOutcome = INCONCLUSIVE
testState = INITIALIZING
END OF OUTPUT FOR JOB 193
Operation Failed
The GET command has not been successfully executed. A general NACK will indicate possible errors or a specific NACK strictly related to the single command is possible.
DN0933412 Issue 01227
BTSplus mainline commands at the Flexi BSC product family
COSA
Id:0900d805805b0ccc
Application Guidelines:None.
Example of Command Execution:Gettest COSA:NAME=RACK:0/COSA:0;
LOCK COSA
Command Tree:“MANAGED-ELEMENT h BSS-EQUIPMENT h BTSEP h RACK h COSA h LOCK COSA”
Applicability:Phase 2 and Phase 3.
Visibility level: 1.
Command Description:This command changes the administrative state of COSA (Core Satellite interface module).
Long Names:NAME Address of the managed object
System Responses:Operation Completed
The specified change of administrative state has been perfomed:
testMonitor it is a list of all test phases related to the selected object; for each phase the related phaseStatus is provided (Passed, Failed, Running or Waiting).
phaseId =
phaseStatus =
phaseId =
phaseStatus =
...
...
testOutcome It represents the test result: it can be Inconclusive (if the phases already executed were successful) or Fail (if at least one of the executed phases failed).
testState = Testing It can assume one of the following values: not_initialized, idle, initializing, sus-pended, testing, terminating and dis-abled.
LOCK COSA NAME=RACK:0..7/COSA:0..1;
228DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805b0ccc
COSA
JOB: 149
PC Time&Date: 16:45:07 03/23/2005
NE Time&Date: 16:43:01 09/15/2004
USER NAME: NSN
COMMAND: Lock COSA:NAME=RACK:0/COSA:1;
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: Operation successful
administrativeState = Locked
END OF OUTPUT FOR JOB 149
CHANGED STATE EVENT REPORT:
This provides information about the administrative state, the operational state and the availability status every time a state change occurs:
JOB: 150
PC Time&Date: 16:45:07 03/23/2005
NE Time&Date: 16:43:01 09/15/2004
USER NAME: NSN
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: Operation successful
CHANGED STATE EVENT REPORT:
NAME = RACK:0/COSA:1
Administrative State = LOCKED
Notification Identifier = 542
END OF OUTPUT FOR JOB 150
Operation Failed
The specified change of administrative state has not been performed.
DN0933412 Issue 01229
BTSplus mainline commands at the Flexi BSC product family
COSA
Id:0900d805805b0ccc
Application Guidelines:If the second line does not end in the first station (or is looped back by a plug!) also the following points must considered for BS240/241 and BS40/41:
• Before a LOCK COSA command (over this board the information of the second line is distributed within the BS240/241 and BS40/41) is applied by the user, the user should lock the service distributed over the second line to this BTSE otherwise some channels (associated to a COBA CU) remain enabled
• In case of a defective COSA, the channels which are associated to a COBA CU but transported over the second line remain enabled
Example of Command Execution:Lock COSA:NAME=RACK:0/COSA:0;
PERFTEST COSA
Command Tree:“MANAGED-ELEMENT h BSS-EQUIPMENT h BTSEP h RACK h COSA h PERFTEST COSA”
Applicability:Phase 2 and Phase 3.
Visibility level: 1.
Command Description:This command is used to start an asynchronous test in COSA.
Long Names:NAME Address of the managed object
System Responses:Operation Completed
Test configuration has been set and the specified test has been started. The System response will not be addressed to the MOT but to the object BTSE.
JOB: 193
PC Time&Date: 12:08:42 03/23/2005
NE Time&Date: 13:09:41 09/15/2004
USER NAME: NSN
COMMAND: Perftest COSA:NAME=RACK:0/COSA:0;
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: Operation successful
PERFTEST COSA NAME=RACK:0..7/COSA:0..1;
230DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805b0ccc
COSA
MOT = RACK:0/COSA:0
tO = BTSETEST:8
END OF OUTPUT FOR JOB 193
JOB: 194
PC Time&Date: 12:08:55 03/23/2005
NE Time&Date: 13:09:59 09/15/2004
USER NAME: NSN
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: Operation successful
ChangedConfigurationNotification:
name = BTSETEST:8
ChangeInfo = created
END OF OUTPUT FOR JOB 194
JOB: 195
PC Time&Date: 12:09:05 03/23/2005
NE Time&Date: 13:10:11 09/15/2004
USER NAME: NSN
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: Operation successful
CHANGED STATE EVENT REPORT:
NAME = RACK:0/COSA:0
Operational State = ENABLED
Availability Status = NULL_value
Standby Status = Cold_Standby
Notification Identifier = 220
END OF OUTPUT FOR JOB 195
DN0933412 Issue 01231
BTSplus mainline commands at the Flexi BSC product family
COSA
Id:0900d805805b0ccc
JOB: 196
PC Time&Date: 12:09:16 03/23/2005
NE Time&Date: 13:10:22 09/15/2004
USER NAME: NSN
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: Operation successful
Test Report:
name = BTSETEST:8
testOutcome = PASSED
testTermination = Normal
MOT = RACK:0/COSA:0
executedPhases =
PreliminaryTestsCosa
SerialEepromTestCosa
EndTestCosa
END OF OUTPUT FOR JOB 196
JOB: 197
PC Time&Date: 12:09:23 03/23/2005
NE Time&Date: 13:10:34 09/15/2004
USER NAME: NSN
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: Operation successful
ChangedConfigurationNotification:
name = BTSETEST:8
ChangeInfo = deleted
END OF OUTPUT FOR JOB 197
232DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805b0ccc
COSA
Operation Failed
This NACK-message occurs in the following cases: Message cannot be performed, test not supported, capacity restrictions, physical configuration cannot be performed, object not locked.
Application Guidelines:
• In phase 3 MO must be locked previous to the command execution
The test results will be displayed at the end of the test phases.
Result TEST:
name = TEST:<n>
testOutcome = This field represents the test result; one of the fol-lowing values can be displayed:
Pass all the test phases are successfully performed.
Inconclusive the test is aborted by the system or the test is terminated by the opera-tor.
Fail if at least one of the executed phases fail.
mOts = It is the identifier of the hardware object under test.
testTermination = It specifies how the test is terminated, it can assume the following values:
Normal all the test phases are performed.
Abort the test is aborted by system.
Cancel the test is terminated by operator.
executedPhases
phaseId = It represents the list of the executed test phases (in case of successful test result, all the test phases will be listed).
additionalWords =
....
failedPhases
phaseId = It represents the list of the failed test phase; addi-tional information is provided for each phase.phaseId =
....
skippedPhases
phaseId = It represents the list of the skipped phases; they are displayed only for test stopped during it execution.phaseId =
....
poprosedRepair Action =
A list of most probable fail probable causes is shown (max four messages)
DN0933412 Issue 01233
BTSplus mainline commands at the Flexi BSC product family
COSA
Id:0900d805805b0ccc
Example of Command Execution:Perftest COSA:NAME=RACK:0/COSA:0;
STOPTEST COSA
Command Tree:“MANAGED-ELEMENT h BSS-EQUIPMENT h BTSEP h RACK h COSA h STOPTEST COSA”
Applicability:Phase 2 and Phase 3.
Visibility level: 1.
Command Description:This command is used to stop a diagnostic previously started.
Long Names:NAME Address of the managed object
System Responses:Operation Completed
Test has been stopped. The System Responses will not be addressed to the MOT but to the object BTSEP.
STOPTEST COSA NAME=RACK:0..7/COSA:0..1;
Result TEST:
name = TEST:<n>
testOutcome = inconclusive
mOts = It is the identifier of the hardware object under test.
testTermination = Cancel
executedPhases
phaseId = It represents the list of the executed test phases; the list is not shown for test in the waiting list (queued)....
.
failedPhases
phaseId = It represents the list of the failed test phase;
additional information is provided for each phase.phaseId =
....
skippedPhases
phaseId = It represents the list of the skipped phases;the list is not shown for test in the waiting list (queued).phaseId =
234DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805b0ccc
COSA
Operation Failed
Test has not been stopped. This NACK-message can occur when the specified test is not running or in case of test which cannot be stopped.
Application Guidelines:None.
Example of Command Execution:Stoptest COSA:NAME=RACK:0/COSA:0;
UNLOCK COSA
Command Tree:“MANAGED-ELEMENT h BSS-EQUIPMENT h BTSEP h RACK h COSA h UNLOCK COSA”
Applicability:Phase 2 and Phase 3.
Visibility level: 1.
Command Description:This command changes the administrative state of COSA (Core Satellite interface module).
Long Names:NAME Address of the managed object
System Responses:Operation Completed
The specified change of administrative state has been perfomed:
JOB: 151
PC Time&Date: 16:45:12 03/23/2005
NE Time&Date: 16:43:06 09/15/2004
USER NAME: NSN
COMMAND: Unlock COSA:NAME=RACK:0/COSA:0;
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: Operation successful
administrativeState = Unlocked
END OF OUTPUT FOR JOB 151
UNLOCK COSA NAME=RACK:0..7/COSA:0..1;
DN0933412 Issue 01235
BTSplus mainline commands at the Flexi BSC product family
COSA
Id:0900d805805b0ccc
CHANGED STATE EVENT REPORT:
This provides information about the administrative state, the operational state and the availability status every time a state change occurs:
JOB: 152
PC Time&Date: 16:45:12 03/23/2005
NE Time&Date: 16:43:06 09/15/2004
USER NAME: NSN
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: Operation successful
CHANGED STATE EVENT REPORT:
NAME = RACK:0/COSA:0
Administrative State = UNLOCKED
Standby Status = Providing_service
Notification Identifier = 543
END OF OUTPUT FOR JOB 152
Operation Failed
The specified change of administrative state has not been performed.
Application Guidelines:None.
Example of Command Execution:Unlock COSA:NAME=RACK:0/COSA:0;
236DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805b0cce
CU
CUThe CU (Carrier Unit) represents the carrier hardware required for a TRX.
CREATE CU
Command Tree:“MANAGED-ELEMENT h BSS-EQUIPMENT h BTSEP h RACK h CU h CREATE CU”
Applicability:Phase 2 and Phase 3.
Visibility level: 2.
Command Description:This command adds the CU (Carrier Unit) to the BTSE data base.
Long Names:NAME Address of the managed object
RXLEVADJ rxLevAdjust(dB)
TXLEVADJ txLevAdjust(dB)
System Responses:Operation Completed
After command execution, a message of Changed Configuration Notification is dis-played. A further message indicates the result of the operation. An example of create command is the following:
JOB: 124
PC Time&Date: 16:43:07 03/23/2005
NE Time&Date: 16:41:01 09/15/2004
USER NAME: NSN
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: Operation successful
ChangedConfigurationNotification:
name = RACK:0/CU:0
ChangeInfo = created
END OF OUTPUT FOR JOB 124
CREATE CU NAME=RACK:0..7/CU:0..11 [,RXLEVADJ=] [,TXLEVADJ=];
DN0933412 Issue 01237
BTSplus mainline commands at the Flexi BSC product family
CU
Id:0900d805805b0cce
JOB: 125
PC Time&Date: 16:43:08 03/23/2005
NE Time&Date: 16:41:02 09/15/2004
USER NAME: NSN
COMMAND: Create CU:NAME=RACK:0/CU:0;
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: Operation successful
END OF OUTPUT FOR JOB 125
Operation Failed
The specified Object has not been created. In addition to the general NACK causes, a specific NACK cause, which indicates that the command is inconsistent with the physical configuration, is possible. An example is the following:
JOB: 69
PC Time&Date: 16:37:54 03/23/2005
NE Time&Date: 16:35:47 09/15/2004
USER NAME: NSN
COMMAND: Create CU:NAME=RACK:0/CU:0;
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: OPERATION FAILED
Object instance unknown (-9)
END OF OUTPUT FOR JOB 69
Application Guidelines:
• When using the CLI interface for the RXLEVADJ parameter, the negative values must be in brackets (refer to Examples of Command Execution)
Example of Command Execution:Create CU:NAME=RACK:0/CU:0,RXLEVADJ=[-1]-0,TXLEVADJ=1;
DELETE CUDELETE CU NAME=RACK:0..7/CU:0..11;
238DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805b0cce
CU
Command Tree:“MANAGED-ELEMENT h BSS-EQUIPMENT h BTSEP h RACK h CU h DELETE CU”
Applicability:Phase 2 and Phase 3.
Visibility level: 2.
Command Description:This command deletes the CU (Carrier Unit) from the BTSE data base.
Long Names:NAME Address of the managed object
System Responses:Operation Completed
After command execution, a message of Changed Configuration Notification is dis-played. A further message indicates the result of the operation. An example of delete command is the following:
JOB: 138
PC Time&Date: 16:44:00 03/23/2005
NE Time&Date: 16:41:54 09/15/2004
USER NAME: NSN
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: Operation successful
ChangedConfigurationNotification:
name = RACK:0/CU:0
ChangeInfo = deleted
END OF OUTPUT FOR JOB 138
JOB: 139
PC Time&Date: 16:44:00 03/23/2005
NE Time&Date: 16:41:54 09/15/2004
USER NAME: NSN
COMMAND: Delete CU:NAME=RACK:0/CU:0;
DN0933412 Issue 01239
BTSplus mainline commands at the Flexi BSC product family
CU
Id:0900d805805b0cce
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: Operation successful
END OF OUTPUT FOR JOB 139
Operation Failed
The specified Object has not been deleted. Additionally to the general NACK causes, a specific NACK cause, meaning that the command is inconsistent with physical configu-ration, is possible.
Application Guidelines:
• CU has to be locked in Phase 3 before deletion
Example of Command Execution:Delete CU:NAME=RACK:0/CU:0;
GET CU
Command Tree:“MANAGED-ELEMENT h BSS-EQUIPMENT h BTSEP h RACK h CU h GET CU”
Applicability:Phase 2 and Phase 3.
Visibility level: 0.
Command Description:This command displays the attributes of the CU (Carrier Unit).
Long Names:NAME Address of the managed object
REQATTL Required attribute list
ALS alarmStatus
AST administrativeState
AVS availabilityStatus
BSWVER bootSoftwareVersion
CCPBL carrierCapability
OST operationalState
OUTPUTPR outputPowerReduction
PRS proceduralStatus
RELFUNCOBJ relatedFuncObjects
RXLEVADJ rxLevAdjust(dB)
GET CU NAME=RACK:0..7/CU:0..11 [,REQATTL=ALS, AST, AVS, BSWVER, CCPBL, OST, OUTPUTPR, PRS, RELFUN-COBJ, RXLEVADJ, TXLEVADJ, FPGAFWVER, STDBYST];
240DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805b0cce
CU
TXLEVADJ txLevAdjust(dB)
FPGAFWVER fpgaFwVer
STDBYST standbyStatus
System Responses:Operation Completed
After command execution, a message of Changed Configuration Notification is dis-played. A further message indicates the result of the operation. An example of get command is the following:
JOB: 127
PC Time&Date: 16:43:13 03/23/2005
NE Time&Date: 16:41:07 09/15/2004
USER NAME: NSN
COMMAND: Get CU:NAME=RACK:0/CU:0;
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: Operation successful
alarmStatus = CLEARED
administrativeState = Unlocked
availabilityStatus = NotInstalled
bootSoftwareVersion = ""
carrierCapability = unknown
outputPowerReduction = 0
operationalState = DISABLED
proceduralStatus = NULL
relatedFuncObjects =
rxLevAdjust(dB) =
adjustValue = 0.0
adjustDivValue = 0.0
txLevAdjust(dB) = 0.0
END OF OUTPUT FOR JOB 127
Operation Failed
The GET command has not been successfully executed. A general NACK will indicate possible errors or a specific NACK strictly related to the single command is possible.
DN0933412 Issue 01241
BTSplus mainline commands at the Flexi BSC product family
CU
Id:0900d805805b0cce
Application Guidelines:
• The value for the attribute GSM functional ID in LMT Evolution Phase 2 is "not con-figured"
• CCPBL: After creation in advance of a CU object the attribute has the value "unknown" in case of hh-ii =04-01 and hh-ii = 04-06. The value "fourRXdiv" is used always in combination with either the value "gsm" or "edge"
Example of Command Execution:Get CU:NAME=RACK:0/CU:0,REQATTL=ALS&AST&AVS&BSWVER&CCPBL&
OUTPUTPR&OST&PRS&RELFUNCOBJ&RXLEVADJ;
GET CU FWID
Command Tree:“MANAGED-ELEMENT h BSS-EQUIPMENT h BTSEP h RACK h CU h GET CU FWID”
Applicability:Phase 2 and Phase 3.
Visibility level: 0.
Command Description:This command provides information on the FPGA FW images that are contained in the boards flash prom together with an indication of the “active” version. Up to 4 images are provided per board. For FlexCUv2 or ECUv6 boards the FPGA FW versions are provided together with an indication whether the FW version is the active one.
Long Names:NAME Address of the managed object
REQATTL Required attribute list
System Responses:Operation Completed
A message indicates the result of the operation. An example of get command is the fol-lowing:
JOB: 6.
PC Time&Date: 26.06.2008 11:13:51 +02:00
NE Time&Date: 01.01.1990 00:13:15 +00:00
USER NAME: NSN
COMMAND: Get CU FWID:NAME=RACK:0/CU:0;SW RELEASE: 01-04-19-01-09-01_08-06-23
COMMAND RESULT: Operation successful
fpgaFwVer = Null
END OF OUTPUT FOR JOB 6
GET CU FWID NAME=RACK:0..7/CU:0..11;
242DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805b0cce
CU
Operation Failed
None.
Application Guidelines:None.
Example of Command Execution:Get CU FWID:NAME=RACK:0/CU:0,REQATTL=FPGAFWVER;
GET CU WIRING
Command Tree:“MANAGED-ELEMENT h BSS-EQUIPMENT h BTSEP h RACK h CU h GET CU WIRING”
Applicability:Phase 2 and Phase 3.
Visibility level: 0.
Command Description:This command displays the attributes of the CU (Carrier Unit).
Long Names:NAME Address of the managed object
REQATTL Required attribute list
System Responses:Operation Completed
After command execution, a message of Changed Configuration Notification is dis-played. A further message indicates the result of the operation. An example of get wiring command is the following:
JOB: 127
PC Time&Date: 16:43:13 03/23/2005
NE Time&Date: 16:41:07 09/15/2004
USER NAME: NSN
COMMAND: Get CU WIRING:NAME=RACK:0/CU:0;
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: Operation successful
cuWiring =
GET CU WIRING NAME=RACK:0..7/CU:0..11;
DN0933412 Issue 01243
BTSplus mainline commands at the Flexi BSC product family
CU
Id:0900d805805b0cce
variable
rxNWiring = RACK:0/DULNA:0
END OF OUTPUT FOR JOB 127
Operation Failed
The GET command has not been successfully executed. A general NACK will indicate possible errors or a specific NACK strictly related to the single command is possible.
Application Guidelines:
• Refer to “CUWIRING”
Example of Command Execution:Get CU WIRING:NAME=RACK:0/CU:0;
GETTEST CU
Command Tree:“MANAGED-ELEMENT h BSS-EQUIPMENT h BTSEP h RACK h CU h GETTEST CU”
Applicability:Phase 2 and Phase 3.
Visibility level: 0.
Command Description:This command displays the attributes of the object test.
Long Names:NAME Address of the managed object
REQATTL Required attribute list
System Responses:Operation Completed
After command execution, a message of Changed Configuration Notification is dis-played. A further message indicates the result of the operation. An example of gettest command is the following:
JOB: 198
PC Time&Date: 12:11:08 03/23/2005
NE Time&Date: 13:12:44 09/15/2004
USER NAME: NSN
COMMAND: Gettest CU:NAME=RACK:0/CU:0;
GETTEST CU NAME=RACK:0..7/CU:0..11;
244DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805b0cce
CU
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: Operation successful
MOT = RACK:0/CU:0
testMonitor =
phaseId = PreliminaryTestsCu
phaseStatus = Running
phaseId = CheckAlarmStatusCu
phaseStatus = Waiting
phaseId = EndTestCu
phaseStatus = Waiting
testOutcome = INCONCLUSIVE
testState = INITIALIZING
END OF OUTPUT FOR JOB 198
Operation Failed
The GET command has not been successfully executed. A general NACK will indicate possible errors or a specific NACK strictly related to the single command is possible.
Application Guidelines:None.
Example of Command Execution:Gettest CU:NAME=RACK:0/CU:0;
testMonitor it is a list of all test phases related to the selected object; for each phase the related phaseStatus is provided (Passed, Failed, Running or Waiting).
phaseId =
phaseStatus =
phaseId =
phaseStatus =
...
...
testOutcome It represents the test result: it can be Inconclusive (if the phases already executed were successful) or Fail (if at least one of the executed phases failed).
testState = Testing It can assume one of the following values: not_initialized, idle, initializing, sus-pended, testing, terminating and dis-abled.
DN0933412 Issue 01245
BTSplus mainline commands at the Flexi BSC product family
CU
Id:0900d805805b0cce
LOCK CU
Command Tree:“MANAGED-ELEMENT h BSS-EQUIPMENT h BTSEP h RACK h CU h LOCK CU”
Applicability:Phase 2 and Phase 3.
Visibility level: 1.
Command Description:This command changes the administrative state of CU (Carrier Unit).
Long Names:NAME Address of the managed object
System Responses:Operation Completed
The specified change of administrative state has been perfomed:
JOB: 132
PC Time&Date: 16:43:41 03/23/2005
NE Time&Date: 16:41:35 09/15/2004
USER NAME: NSN
COMMAND: Lock CU:NAME=RACK:0/CU:0;
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: Operation successful
administrativeState = Locked
END OF OUTPUT FOR JOB 132
CHANGED STATE EVENT REPORT:
This provides information about the administrative state, the operational state and the availability status every time a state change occurs:
JOB: 133
PC Time&Date: 16:43:41 03/23/2005
NE Time&Date: 16:41:35 09/15/2004
LOCK CU NAME=RACK:0..7/CU:0..11;
246DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805b0cce
CU
USER NAME: NSN
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: Operation successful
CHANGED STATE EVENT REPORT:
NAME = RACK:0/CU:0
Administrative State = LOCKED
Notification Identifier = 534
END OF OUTPUT FOR JOB 133
Operation Failed
The specified change of administrative state has not been performed.
Application Guidelines:None.
Example of Command Execution:Lock CU:NAME=RACK:0/CU:0;
PERFTEST CU
Command Tree:“MANAGED-ELEMENT h BSS-EQUIPMENT h BTSEP h RACK h CU h PERFTEST CU”
Applicability:Phase 2 and Phase 3.
Visibility level: 1.
Command Description:This command is used to start an asynchronous test in the object.
Long Names:NAME Address of the managed object
System Responses:Operation Completed
Test configuration has been set and the specified test has been started. The System response will not be addressed to the MOT but to the object BTSEP.
JOB: 199
PERFTEST CU NAME=RACK:0..7/CU:0..11;
DN0933412 Issue 01247
BTSplus mainline commands at the Flexi BSC product family
CU
Id:0900d805805b0cce
PC Time&Date: 12:11:12 03/23/2005
NE Time&Date: 13:12:48 09/15/2004
USER NAME: NSN
COMMAND: Perftest CU:NAME=RACK:0/CU:0;
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: Operation successful
MOT = RACK:0/CU:0
tO = BTSETEST:1
END OF OUTPUT FOR JOB 199
JOB: 200
PC Time&Date: 12:11:12 03/23/2005
NE Time&Date: 13:12:48 09/15/2004
USER NAME: NSN
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: Operation successful
ChangedConfigurationNotification:
name = BTSETEST:1
ChangeInfo = created
END OF OUTPUT FOR JOB 200
JOB: 201
PC Time&Date: 12:11:12 03/23/2005
NE Time&Date: 13:12:59 09/15/2004
USER NAME: NSN
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: Operation successful
248DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805b0cce
CU
CHANGED STATE EVENT REPORT:
NAME = RACK:0/CU:0
Operational State = ENABLED
Availability Status = NULL_value
Standby Status = Cold_Standby
Notification Identifier = 123
END OF OUTPUT FOR JOB 201
JOB: 202
PC Time&Date: 12:11:18 03/23/2005
NE Time&Date: 13:13:11 09/15/2004
USER NAME: NSN
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: Operation successful
Test Report:
name = BTSETEST:1
testOutcome = PASSED
testTermination = Normal
MOT = RACK:0/CU:0
executedPhases =
PreliminaryTestsCu
SerialEepromTestCu
EndTestCu
END OF OUTPUT FOR JOB 202
JOB: 203
PC Time&Date: 12:11:20 03/23/2005
NE Time&Date: 13:13:25 09/15/2004
USER NAME: NSN
DN0933412 Issue 01249
BTSplus mainline commands at the Flexi BSC product family
CU
Id:0900d805805b0cce
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: Operation successful
ChangedConfigurationNotification:
name = BTSETEST:1
ChangeInfo = deleted
END OF OUTPUT FOR JOB 203
The test results will be displayed at the end of the test phases.
Result TEST:
name = TEST:<n>
testOutcome = This field represents the test result; one of the fol-lowing values can be displayed:
Pass all the test phases are successfully performed.
Inconclusive the test is aborted by the system or the test is terminated by the opera-tor.
Fail if at least one of the executed phases fail.
mOts = It is the identifier of the hardware object under test.
testTermination = It specifies how the test is terminated, it can assume the following values:
Normal all the test phases are performed.
Abort the test is aborted by system.
Cancel the test is terminated by operator.
executedPhases
phaseId = It represents the list of the executed test phases (in case of successful test result, all the test phases will be listed).
additionalWords =
....
failedPhases
phaseId = It represents the list of the failed test phase; addi-tional information is provided for each phase.phaseId =
....
skippedPhases
250DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805b0cce
CU
Operation Failed
This NACK-message occurs in the following cases: Message cannot be performed, test not supported, capacity restrictions, physical configuration cannot be performed, object not locked.
Application Guidelines:
• In phase 3 MO must be locked previous to the command execution
Example of Command Execution:Perftest CU:NAME=RACK:0/CU:0;
SET CU
Command Tree:“MANAGED-ELEMENT h BSS-EQUIPMENT h BTSEP h RACK h CU h SET CU”
Applicability:Phase 2 and Phase 3.
Visibility level: 2.
Command Description:This command sets the attributes of CU (Carrier Unit) to the BTSE data base.
Long Names:NAME Address of the managed object
RXLEVADJ rxLevAdjust(dB)
TXLEVADJ txLevAdjust(dB)
System Responses:Operation Completed
After command execution, a message of Changed Attribute Event Report is displayed. A further message indicates the result of the operation. An example of set command is the following:
JOB: 131
PC Time&Date: 16:43:27 03/23/2005
phaseId = It represents the list of the skipped phases; they are displayed only for test stopped during it execution.phaseId =
....
poprosedRepair Action =
A list of most probable fail probable causes is shown (max four messages)
SET CU NAME=RACK:0..7/CU:0..11 [,RXLEVADJ=] [,TXLEVADJ=];
DN0933412 Issue 01251
BTSplus mainline commands at the Flexi BSC product family
CU
Id:0900d805805b0cce
NE Time&Date: 16:41:21 09/15/2004
USER NAME: NSN
COMMAND: Set CU:NAME=RACK:0/CU:0;
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: Operation successful
END OF OUTPUT FOR JOB 131
Operation Failed
The specified attributes have not been set. In addition to the general NACK causes, a specific NACK cause, which indicates that the command is inconsistent with the physical configuration, is possible.
Application Guidelines:
• When using the CLI interface for the RXLEVADJ parameter, the negative values must be in brackets (see Example of Command Execution)
• The MGMSKOUTPUTP power reduction parameter is used for all existing high power variants ECUxHPV2 and ECUxHPV3 (x= D or P)
Example of Command Execution:Set CU:NAME=RACK:0/CU:0,TXLEVADJ=1,RXLEVADJ=[-1]-[-1];
STOPTEST CU
Command Tree:“MANAGED-ELEMENT h BSS-EQUIPMENT h BTSEP h RACK h CU h STOPTEST CU”
Applicability:Phase 2 and Phase 3.
Visibility level: 1.
Command Description:This command is used to stop a diagnostic previously started.
Long Names:NAME Address of the managed object
System Responses:Operation Completed
Test has been stopped. The System Responses will not be addressed to the MOT but to the object BTSEP.
STOPTEST CU NAME=RACK:0..7/CU:0..11;
252DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805b0cce
CU
Operation Failed
Test has not been stopped. This NACK-message can occur when the specified test is not running or in case of test which cannot be stopped.
Application Guidelines:None.
Example of Command Execution:Stoptest CU:NAME=RACK:0/CU:0;
UNLOCK CU
Command Tree:“MANAGED-ELEMENT h BSS-EQUIPMENT h BTSEP h RACK h CU h UNLOCK CU”
Applicability:Phase 2 and Phase 3.
Visibility level: 1.
Command Description:This command changes the administrative state of CU (Carrier Unit).
Long Names:NAME Address of the managed object
Result TEST:
name = TEST:<n>
testOutcome = inconclusive
mOts = It is the identifier of the hardware object under test.
testTermination = Cancel
executedPhases
phaseId = It represents the list of the executed test phases; the list is not shown for test in the waiting list (queued)....
.
failedPhases
phaseId = It represents the list of the failed test phase;
additional information is provided for each phase.phaseId =
....
skippedPhases
phaseId = It represents the list of the skipped phases;the list is not shown for test in the waiting list (queued).phaseId =
UNLOCK CU NAME=RACK:0..7/CU:0..11;
DN0933412 Issue 01253
BTSplus mainline commands at the Flexi BSC product family
CU
Id:0900d805805b0cce
System Responses:Operation Completed
The specified change of administrative state has been perfomed:
JOB: 134
PC Time&Date: 16:43:50 03/23/2005
NE Time&Date: 16:41:44 09/15/2004
USER NAME: NSN
COMMAND: Unlock CU:NAME=RACK:0/CU:0;
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: Operation successful
administrativeState = Unlocked
END OF OUTPUT FOR JOB 134
CHANGED STATE EVENT REPORT:
This provides information about the administrative state, the operational state and the availability status every time a state change occurs:
JOB: 135
PC Time&Date: 16:43:50 03/23/2005
NE Time&Date: 16:41:44 09/15/2004
USER NAME: NSN
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: Operation successful
CHANGED STATE EVENT REPORT:
NAME = RACK:0/CU:0
Administrative State = UNLOCKED
Notification Identifier = 535
END OF OUTPUT FOR JOB 135
254DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805b0cce
CU
Operation Failed
The specified change of administrative state has not been performed.
Application Guidelines:None.
Example of Command Execution:Unlock CU:NAME=RACK:0/CU:0;
DN0933412 Issue 01255
BTSplus mainline commands at the Flexi BSC product family
DIDCTMA
Id:0900d805805b1080
DIDCTMAThe DIDCTMA object represents the power supply module of a TMA (Tower Mounted Amplifier) connected to DIAMCO.
CREATE DIDCTMA
Command Tree:“MANAGED-ELEMENT h BSS-EQUIPMENT h BTSEP h RACK h DIDCTMA h CREATE DIDCTMA”
Applicability:Phase 2 and Phase 3.
Visibility level: 2.
Command Description:This command adds the DIAMCO_DC_TMA (DC Power Supply Module of TMA) to the BTSE data base.
Long Names:NAME Address of the managed object
System Responses:Operation Completed
After command execution, a message of Changed Configuration Notification is dis-played. A further message indicates the result of the operation. An example of create command is the following:
JOB: 111
PC Time&Date: 16:41:43 03/23/2005
NE Time&Date: 16:39:37 09/15/2004
USER NAME: NSN
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: Operation successful
ChangedConfigurationNotification:
name = RACK:0/DIDCTMA:0
ChangeInfo = created
END OF OUTPUT FOR JOB 111
CREATE DIDCTMA NAME=RACK:0..7/DIDCTMA:0..7;
256DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805b1080
DIDCTMA
JOB: 112
PC Time&Date: 16:41:43 03/23/2005
NE Time&Date: 16:39:37 09/15/2004
USER NAME: NSN
COMMAND: Create DIDCTMA:NAME=RACK:0/DIDCTMA:0;
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: Operation successful
END OF OUTPUT FOR JOB 112
Operation Failed
The specified Object has not been created. In addition to the general NACK causes, a specific NACK cause, which indicates that the command is inconsistent with the physical configuration, is possible. An example is the following:
JOB: 68
PC Time&Date: 16:37:54 03/23/2005
NE Time&Date: 16:35:47 09/15/2004
USER NAME: NSN
COMMAND: Create DIDCTMA:NAME=RACK:0/DIDCTMA:0;
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: OPERATION FAILED
Message cannot be performed (-17)
END OF OUTPUT FOR JOB 68
Application Guidelines:None.
Example of Command Execution:Create DIDCTMA:NAME=RACK:0/DIDCTMA:0;
DELETE DIDCTMADELETE DIDCTMA NAME=RACK:0..7/DIDCTMA:0..7;
DN0933412 Issue 01257
BTSplus mainline commands at the Flexi BSC product family
DIDCTMA
Id:0900d805805b1080
Command Tree:“MANAGED-ELEMENT h BSS-EQUIPMENT h BTSEP h RACK h DIDCTMA h DELETE DIDCTMA”
Applicability:Phase 2 and Phase 3.
Visibility level: 2.
Command Description:This command deletes the DIAMCO_DC_TMA (DC Power Supply Module of TMA) from the BTSE data base.
Long Names:NAME Address of the managed object
System Responses:Operation Completed
After command execution, a message of Changed Configuration Notification is dis-played. A further message indicates the result of the operation. An example of delete command is the following:
JOB: 120
PC Time&Date: 16:42:08 03/23/2005
NE Time&Date: 16:40:02 09/15/2004
USER NAME: NSN
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: Operation successful
ChangedConfigurationNotification:
name = RACK:0/DIDCTMA:0
ChangeInfo = deleted
END OF OUTPUT FOR JOB 120
JOB: 121
PC Time&Date: 16:42:08 03/23/2005
NE Time&Date: 16:40:02 09/15/2004
USER NAME: NSN
258DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805b1080
DIDCTMA
COMMAND: Delete DIDCTMA:NAME=RACK:0/DIDCTMA:0;
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: Operation successful
END OF OUTPUT FOR JOB 121
Operation Failed
The specified Object has not been deleted. Additionally to the general NACK causes, a specific NACK cause, meaning that the command is inconsistent with physical configu-ration, is possible.
Application Guidelines:
• DIDCTMA must be locked in phase 3 before deletion
Example of Command Execution:Delete DIDCTMA:NAME=RACK:0/DIDCTMA:0;
GET DIDCTMA
Command Tree:“MANAGED-ELEMENT h BSS-EQUIPMENT h BTSEP h RACK h DIDCTMA h GET DIDCTMA”
Applicability:Phase 2 and Phase 3.
Visibility level: 0.
Command Description:This command displays the attributes of the DIAMCO_DC_TMA (DC Power Supply Module of TMA).
Long Names:NAME Address of the managed object
REQATTL Required attribute list
ALS alarmStatus
AST administrativeState
AVS availabilityStatus
OST operationalState
PRS proceduralStatus
RELFUNCOBJ relatedFuncObjects
System Responses:Operation Completed
GET DIDCTMA NAME=RACK:0..7/DIDCTMA:0..7 [,REQATTL=ALS, AST, AVS, OST, PRS, RELFUNCOBJ];
DN0933412 Issue 01259
BTSplus mainline commands at the Flexi BSC product family
DIDCTMA
Id:0900d805805b1080
After command execution, a message of Changed Configuration Notification is dis-played. A further message indicates the result of the operation. An example of get command is the following:
JOB: 113
PC Time&Date: 16:41:48 03/23/2005
NE Time&Date: 16:39:41 09/15/2004
USER NAME: NSN
COMMAND: Get DIDCTMA:NAME=RACK:0/DIDCTMA:0;
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: Operation successful
alarmStatus = CLEARED
administrativeState = Unlocked
availabilityStatus = NotInstalled
operationalState = DISABLED
proceduralStatus = NULL
relatedFuncObjects =
END OF OUTPUT FOR JOB 113
Operation Failed
The GET command has not been successfully executed. A general NACK will indicate possible errors or a specific NACK strictly related to the single command is possible.
Application Guidelines:None.
Example of Command Execution:Get DIDCTMA:NAME=RACK:0/DIDCTMA:0,REQATTL=ALS&AST&AVS&OST&PRS;
GETTEST DIDCTMA
Command Tree:“MANAGED-ELEMENT h BSS-EQUIPMENT h BTSEP h RACK h DIDCTMA h GETTEST DIDCTMA”
Applicability:Phase 2 and Phase 3.
Visibility level: 0.
GETTEST DIDCTMA NAME=RACK:0..7/DIDCTMA:0..7;
260DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805b1080
DIDCTMA
Command Description:This command displays the attributes of the object test.
Long Names:NAME Address of the managed object
REQATTL Required attribute list
System Responses:Operation Completed
After command execution, a message of Changed Configuration Notification is dis-played. A further message indicates the result of the operation. An example of gettest command is the following:
JOB: 204
PC Time&Date: 12:11:28 03/23/2005
NE Time&Date: 13:13:04 09/15/2004
USER NAME: NSN
COMMAND: Gettest DIDCTMA:NAME=RACK:0/DIDCTMA:0;
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: Operation successful
MOT = RACK:0/DIDCTMA:0
testMonitor =
phaseId = PreliminaryTestsDidctma
phaseStatus = Running
phaseId = CheckAlarmStatusDidctma
phaseStatus = Waiting
phaseId = EndTestDidctma
phaseStatus = Waiting
testOutcome = INCONCLUSIVE
testState = INITIALIZING
END OF OUTPUT FOR JOB 204
Operation Failed
The GET command has not been successfully executed. A general NACK will indicate possible errors or a specific NACK strictly related to the single command is possible.
DN0933412 Issue 01261
BTSplus mainline commands at the Flexi BSC product family
DIDCTMA
Id:0900d805805b1080
Application Guidelines:None.
Example of Command Execution:Gettest DIDCTMA:NAME=RACK:0/DIDCTMA:0;
LOCK DIDCTMA
Command Tree:“MANAGED-ELEMENT h BSS-EQUIPMENT h BTSEP h RACK h DIDCTMA h LOCK DIDCTMA”
Applicability:Phase 2 and Phase 3.
Visibility level: 1.
Command Description:This command changes the administrative state of DIAMCO_DC_TMA (DC Power Supply Module of TMA).
Long Names:NAME Address of the managed object
System Responses:Operation Completed
The specified change of administrative state has been perfomed:
testMonitor it is a list of all test phases related to the selected object; for each phase the related phaseStatus is provided (Passed, Failed, Running or Waiting).
phaseId =
phaseStatus =
phaseId =
phaseStatus =
...
...
testOutcome It represents the test result: it can be Inconclusive (if the phases already executed were successful) or Fail (if at least one of the executed phases failed).
testState = Testing It can assume one of the following values: not_initialized, idle, initializing, sus-pended, testing, terminating and dis-abled.
LOCK DIDCTMA NAME=RACK:0..7/DIDCTMA:0..7;
262DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805b1080
DIDCTMA
JOB: 114
PC Time&Date: 16:41:53 03/23/2005
NE Time&Date: 16:39:47 09/15/2004
USER NAME: NSN
COMMAND: Lock DIDCTMA:NAME=RACK:0/DIDCTMA:0;
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: Operation successful
administrativeState = Locked
END OF OUTPUT FOR JOB 114
CHANGED STATE EVENT REPORT:
This provides information about the administrative state, the operational state and the availability status every time a state change occurs:
JOB: 115
PC Time&Date: 16:41:53 03/23/2005
NE Time&Date: 16:39:47 09/15/2004
USER NAME: NSN
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: Operation successful
CHANGED STATE EVENT REPORT:
NAME = RACK:0/DIDCTMA:0
Administrative State = LOCKED
Notification Identifier = 525
END OF OUTPUT FOR JOB 115
Operation Failed
The specified change of administrative state has not been performed.
Application Guidelines:None.
DN0933412 Issue 01263
BTSplus mainline commands at the Flexi BSC product family
DIDCTMA
Id:0900d805805b1080
Example of Command Execution:Lock DIDCTMA:NAME=RACK:0/DIDCTMA:0;
PERFTEST DIDCTMA
Command Tree:“MANAGED-ELEMENT h BSS-EQUIPMENT h BTSEP h RACK h DIDCTMA h PERFTEST DIDCTMA”
Applicability:Phase 2 and Phase 3.
Visibility level: 1.
Command Description:This command is used to start an asynchronous test in DIDCTMA.
Long Names:NAME Address of the managed object
System Responses:Operation Completed
Test configuration has been set and the specified test has been started. The System response will not be addressed to the MOT but to the object BTSEP.
JOB: 205
PC Time&Date: 12:13:07 03/23/2005
NE Time&Date: 13:14:42 09/15/2004
USER NAME: NSN
COMMAND: Perftest DIDCTMA:NAME=RACK:0/DIDCTMA:0;
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: Operation successful
MOT = RACK:0/DIDCTMA:0
tO = BTSETEST:2
END OF OUTPUT FOR JOB 205
JOB: 206
PC Time&Date: 12:13:22 03/23/2005
PERFTEST DIDCTMA NAME=RACK:0..7/DIDCTMA:0..7;
264DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805b1080
DIDCTMA
NE Time&Date: 13:14:57 09/15/2004
USER NAME: NSN
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: Operation successful
ChangedConfigurationNotification:
name = BTSETEST:2
ChangeInfo = created
END OF OUTPUT FOR JOB 206
JOB: 207
PC Time&Date: 12:13:31 03/23/2005
NE Time&Date: 13:15:06 09/15/2004
USER NAME: NSN
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: Operation successful
CHANGED STATE EVENT REPORT:
NAME = RACK:0/DIDCTMA:0
Operational State = ENABLED
Availability Status = NULL_value
Standby Status = Cold_Standby
Notification Identifier = 146
END OF OUTPUT FOR JOB 207
JOB: 208
PC Time&Date: 12:13:35 03/23/2005
NE Time&Date: 13:15:10 09/15/2004
USER NAME: NSN
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: Operation successful
DN0933412 Issue 01265
BTSplus mainline commands at the Flexi BSC product family
DIDCTMA
Id:0900d805805b1080
Test Report:
name = BTSETEST:2
testOutcome = PASSED
testTermination = Normal
MOT = RACK:0/DIDCTMA:0
executedPhases =
PreliminaryTestsDidctma
SerialEepromTestDidctma
EndTestDidctma
END OF OUTPUT FOR JOB 208
JOB: 209
PC Time&Date: 12:13:35 03/23/2005
NE Time&Date: 13:15:10 09/15/2004
USER NAME: NSN
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: Operation successful
ChangedConfigurationNotification:
name = BTSETEST:2
ChangeInfo = deleted
END OF OUTPUT FOR JOB 209
The test results will be displayed at the end of the test phases.
Result TEST:
name = TEST:<n>
testOutcome = This field represents the test result; one of the fol-lowing values can be displayed:
Pass all the test phases are successfully performed.
Inconclusive the test is aborted by the system or the test is terminated by the opera-tor.
266DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805b1080
DIDCTMA
Operation Failed
This NACK-message occurs in the following cases: Message cannot be performed, test not supported, capacity restrictions, physical configuration cannot be performed, object not locked.
Application Guidelines:
• In phase 3 MO must be locked previous to the command execution
Example of Command Execution:Perftest DIDCTMA:NAME=RACK:0/DIDCTMA:0;
STOPTEST DIDCTMA
Command Tree:“MANAGED-ELEMENT h BSS-EQUIPMENT h BTSEP h RACK h DIDCTMA h STOPTEST DIDCTMA”
Fail if at least one of the executed phases fail.
mOts = It is the identifier of the hardware object under test.
testTermination = It specifies how the test is terminated, it can assume the following values:
Normal all the test phases are performed.
Abort the test is aborted by system.
Cancel the test is terminated by operator.
executedPhases
phaseId = It represents the list of the executed test phases (in case of successful test result, all the test phases will be listed).
additionalWords =
....
failedPhases
phaseId = It represents the list of the failed test phase; addi-tional information is provided for each phase.phaseId =
....
skippedPhases
phaseId = It represents the list of the skipped phases; they are displayed only for test stopped during it execution.phaseId =
....
poprosedRepair Action =
A list of most probable fail probable causes is shown (max four messages)
STOPTEST DIDCTMA NAME=RACK:0..7/DIDCTMA:0..7;
DN0933412 Issue 01267
BTSplus mainline commands at the Flexi BSC product family
DIDCTMA
Id:0900d805805b1080
Applicability:Phase 2 and Phase 3.
Visibility level: 1.
Command Description:This command is used to stop a diagnostic previously started.
Long Names:NAME Address of the managed object
System Responses:Operation Completed
Test has been stopped. The System Responses will not be addressed to the MOT but to the object BTSEP.
Operation Failed
Test has not been stopped. This NACK-message can occur when the specified test is not running or in case of test which cannot be stopped.
Application Guidelines:None.
Example of Command Execution:Stoptest DIDCTMA:NAME=RACK:0/DIDCTMA:0;
Result TEST:
name = TEST:<n>
testOutcome = inconclusive
mOts = It is the identifier of the hardware object under test.
testTermination = Cancel
executedPhases
phaseId = It represents the list of the executed test phases; the list is not shown for test in the waiting list (queued)....
.
failedPhases
phaseId = It represents the list of the failed test phase;
additional information is provided for each phase.phaseId =
....
skippedPhases
phaseId = It represents the list of the skipped phases;the list is not shown for test in the waiting list (queued).phaseId =
268DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805b1080
DIDCTMA
UNLOCK DIDCTMA
Command Tree:“MANAGED-ELEMENT h BSS-EQUIPMENT h BTSEP h RACK h DIDCTMA h UNLOCK DIDCTMA”
Applicability:Phase 2 and Phase 3.
Visibility level: 1.
Command Description:This command changes the administrative state of DIAMCO_DC_TMA (DC Power Supply Module of TMA).
Long Names:NAME Address of the managed object
System Responses:Operation Completed
The specified change of administrative state has been perfomed:
JOB: 116
PC Time&Date: 16:41:57 03/23/2005
NE Time&Date: 16:39:51 09/15/2004
USER NAME: NSN
COMMAND: Unlock DIDCTMA:NAME=RACK:0/DIDCTMA:0;
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: Operation successful
administrativeState = Unlocked
END OF OUTPUT FOR JOB 116
CHANGED STATE EVENT REPORT:
This provides information about the administrative state, the operational state and the availability status every time a state change occurs:
JOB: 117
PC Time&Date: 16:41:57 03/23/2005
UNLOCK DIDCTMA NAME=RACK:0..7/DIDCTMA:0..7;
DN0933412 Issue 01269
BTSplus mainline commands at the Flexi BSC product family
DIDCTMA
Id:0900d805805b1080
NE Time&Date: 16:39:51 09/15/2004
USER NAME: NSN
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: Operation successful
CHANGED STATE EVENT REPORT:
NAME = RACK:0/DIDCTMA:0
Administrative State = UNLOCKED
Notification Identifier = 526
END OF OUTPUT FOR JOB 117
Operation Failed
The specified change of administrative state has not been performed.
Application Guidelines:None.
Example of Command Execution:Unlock DIDCTMA:NAME=RACK:0/DIDCTMA:0;
270DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805b1082
DILNA
DILNAThe DILNA object represents the low noise amplifier of DIAMCO (Diversity Antenna Multicoupler).
CREATE DILNA
Command Tree:“MANAGED-ELEMENT h BSS-EQUIPMENT h BTSEP h RACK h DILNA h CREATE DILNA”
Applicability:Phase 2 and Phase 3.
Visibility level: 2.
Command Description:This command adds the DILNA (Low Noise Amplifier of Diversity Multicoupler) together with its attributes to the BTSE data base.
Long Names:NAME Address of the managed object
CELLNO cellNumber
COMBMD combMode
LNAPRED lnaPredecessor
SCELLNO secondCellNumber
WDLNA wiringDataLna
System Responses:Operation Completed
After command execution, a message of Changed Configuration Notification is dis-played. A further message indicates the result of the operation. An example of create command is the following:
JOB: 96
PC Time&Date: 16:40:26 03/23/2005
NE Time&Date: 16:38:20 09/15/2004
USER NAME: NSN_Frank
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: Operation successful
CREATE DILNA NAME=RACK:0..7/DILNA:0..7 ,CELLNO= [,COMBMD=] [,LNAPRED=] [,SCELLNO=] ,WDLNA=;
DN0933412 Issue 01271
BTSplus mainline commands at the Flexi BSC product family
DILNA
Id:0900d805805b1082
ChangedConfigurationNotification:
name = RACK:0/DILNA:0
ChangeInfo = created
END OF OUTPUT FOR JOB 96
JOB: 97
PC Time&Date: 16:40:26 03/23/2005
NE Time&Date: 16:38:20 09/15/2004
USER NAME: NSN_Frank
COMMAND: Create DILNA:NAME=RACK:0/DILNA:0,CELLNO=1,WDLNA=CU0N;
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: Operation successful
cellNumber = 1
secondCellNumber = 2
wiringDataLna = CU0N
END OF OUTPUT FOR JOB 97
Operation Failed
The specified Object has not been created. In addition to the general NACK causes, a specific NACK cause, which indicates that the command is inconsistent with the physical configuration, is possible. An example is the following:
JOB: 74
PC Time&Date: 16:37:54 03/23/2005
NE Time&Date: 16:35:47 09/15/2004
USER NAME: NSN_Frank
COMMAND: Create DILNA:NAME=RACK:0/DILNA:0,CELLNO=1,WDLNA=CU0N;
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: OPERATION FAILED
Message cannot be performed (-17)
272DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805b1082
DILNA
END OF OUTPUT FOR JOB 74
Application Guidelines:
• The DIAMCO_LNA and the CUs are in the same rack and belong to the same cell
• Each CU has a 'normal path' RX input and a 'diversity path' RX input and the operator must indicate which of them is wired to the DIAMCO_LNA
• If there is no wiring the operator must not provide a value for the attribute LNAPRED (if a get is done the attribute identifier will be put into the list of unavailable attributes)
• If there is no wiring for the attribute LNAPRED and the operator enters a value, this error can be corrected by a deletion of the object and a re-creation of the object
• The BTSE SW doesn't check if the entered "predecessor (relative number)" is com-patible with typeOfBTSE; e.g. an input of TMA 11 is not rejected in a BS40 although BS40 allows only the creation of TMA 0-5
The BTSE SW doesn't check if the entered "predecessor (rack)" is compatible with typeOfBTSE; e.g. an input of RACK 1 is not rejected in a BS40 although BS40 allows only the creation of RACK 0
• Wildcard addressing is not possible
Example of Command Execution:Create DILNA:NAME=RACK:1/DILNA:0,CELLNO=0,COMBMD=EightToTwo,
SCELLNO=2,WDLNA=CU0D&CU1D&CU2D&CU3D,
LNAPRED=TMA (RACK:0-TMA:0);
DELETE DILNA
Command Tree:“MANAGED-ELEMENT h BSS-EQUIPMENT h BTSEP h RACK h DILNA h DELETE DILNA”
Applicability:Phase 2 and Phase 3.
Visibility level: 2.
Command Description:This command deletes the DILNA (Low Noise Amplifier of Diversity Multicoupler) together with its attributes from the BTSE data base.
Long Names:NAME Address of the managed object
System Responses:Operation Completed
After command execution, a message of Changed Configuration Notification is dis-played. A further message indicates the result of the operation. An example of delete command is the following:
DELETE DILNA NAME=RACK:0..7/DILNA:0..7;
DN0933412 Issue 01273
BTSplus mainline commands at the Flexi BSC product family
DILNA
Id:0900d805805b1082
JOB: 106
PC Time&Date: 16:40:51 03/23/2005
NE Time&Date: 16:38:45 09/15/2004
USER NAME: NSN_Frank
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: Operation successful
ChangedConfigurationNotification:
name = RACK:0/DILNA:0
ChangeInfo = deleted
END OF OUTPUT FOR JOB 106
JOB: 107
PC Time&Date: 16:40:51 03/23/2005
NE Time&Date: 16:38:45 09/15/2004
USER NAME: NSN_Frank
COMMAND: Delete DILNA:NAME=RACK:0/DILNA:0;
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: Operation successful
END OF OUTPUT FOR JOB 107
Operation Failed
The specified Object has not been deleted. Additionally to the general NACK causes, a specific NACK cause, meaning that the command is inconsistent with physical configu-ration, is possible.
Application Guidelines:
• DILNA must be locked in Phase 3, before deletion
• If this object is deleted, the related TRXs are out of service
Example of Command Execution:Delete DILNA:NAME=RACK:0/DILNA:0;
274DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805b1082
DILNA
GET DILNA
Command Tree:“MANAGED-ELEMENT h BSS-EQUIPMENT h BTSEP h RACK h DILNA h GET DILNA”
Applicability:Phase 2 and Phase 3.
Visibility level: 0.
Command Description:This command displays the attributes of the DILNA (Low Noise Amplifier of Diversity Multicoupler).
Long Names:NAME Address of the managed object
REQATTL Required attribute list
ALS alarmStatus
AST administrativeState
AVS availabilityStatus
CELLNO cellNumber
GNA gainAdjust(dB)
COMBMD combMode
LNAMODE lnaMode
LNAPRED lnaPredecessor
OST operationalState
PRS proceduralStatus
RELFUNCOBJ relatedFuncObjects
SCELLNO secondCellNumber
WDLNA wiringDataLna
System Responses:Operation Completed
After command execution, a message of Changed Configuration Notification is dis-played. A further message indicates the result of the operation. An example of create command is the following:
JOB: 99
PC Time&Date: 16:40:32 03/23/2005
NE Time&Date: 16:38:26 09/15/2004
GET DILNA NAME=RACK:0..7/DILNA:0..7 [,REQATTL=ALS, AST, AVS, CELLNO, GNA, COMBMD, LNAMODE, LNAPRED, OST, PRS, RELFUNCOBJ, SCELLNO, WDLNA];
DN0933412 Issue 01275
BTSplus mainline commands at the Flexi BSC product family
DILNA
Id:0900d805805b1082
USER NAME: NSN_Frank
COMMAND: Get DILNA:NAME=RACK:0/DILNA:1;
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: Operation successful
alarmStatus = CLEARED
administrativeState = Unlocked
availabilityStatus = NotInstalled
cellNumber = 1
cableLossAdjust(dB) = Null
combMode = EightToTwo
lnaMode = UNKNOWN
lnaPredecessor = Null
operationalState = DISABLED
proceduralStatus = NULL
relatedFuncObjects =
secondCellNumber = NotUsed
wiringDataLna = CU3N & CU2N & CU0D & CU0N
END OF OUTPUT FOR JOB 99
Operation Failed
The GET command has not been successfully executed. A general NACK will indicate possible errors or a specific NACK strictly related to the single command is possible.
Application Guidelines:
• The value for the attribute relatedFuncObjects in LMT Evolution Phase 2 is "not con-figured"
• The value for proceduralStatus must be NULL
Example of Command Execution:Get DILNA:NAME=RACK:0/DILNA:0,REQATTL=ALS&AST&AVS&CELLNO&
CLADJ&COMBMD&LNAMODE&LNAPRED&OST&PRS&SCELLNO&WDLNA;
GETTEST DILNA
Command Tree:“MANAGED-ELEMENT h BSS-EQUIPMENT h BTSEP h RACK h DILNA h GETTEST DILNA”
GETTEST DILNA NAME=RACK:0..7/DILNA:0..7;
276DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805b1082
DILNA
Applicability:Phase 2 and Phase 3.
Visibility level: 0.
Command Description:This command displays the attributes of the object test.
Long Names:NAME Address of the managed object
REQATTL Required attribute list
System Responses:Operation Completed
After command execution, a message of Changed Configuration Notification is dis-played. A further message indicates the result of the operation. An example of get command is the following:
JOB: 210
PC Time&Date: 12:13:35 03/23/2005
NE Time&Date: 13:15:10 09/15/2004
USER NAME: NSN_Frank
COMMAND: Gettest DILNA:NAME=RACK:0/DILNA:0;
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: Operation successful
MOT = RACK:0/DILNA:0
testMonitor =
phaseId = PreliminaryTestsDilna
phaseStatus = Running
phaseId = CheckAlarmStatusDilna
phaseStatus = Waiting
phaseId = EndTestDilna
phaseStatus = Waiting
testOutcome = INCONCLUSIVE
testState = INITIALIZING
END OF OUTPUT FOR JOB 210
Operation Failed
The GET command has not been successfully executed. A general NACK will indicate possible errors or a specific NACK strictly related to the single command is possible.
DN0933412 Issue 01277
BTSplus mainline commands at the Flexi BSC product family
DILNA
Id:0900d805805b1082
Application Guidelines:None.
Example of Command Execution:Gettest DILNA:NAME=RACK:0/DILNA:0;
LOCK DILNA
Command Tree:“MANAGED-ELEMENT h BSS-EQUIPMENT h BTSEP h RACK h DILNA h LOCK DILNA”
Applicability:Phase 2 and Phase 3.
Visibility level: 1.
Command Description:This command changes the administrative state of DILNA (Low Noise Amplifier of Diver-sity Multicoupler).
Long Names:NAME Address of the managed object
System Responses:Operation Completed
The specified change of administrative state has been perfomed:
testMonitor it is a list of all test phases related to the selected object; for each phase the related phaseStatus is provided (Passed, Failed, Running or Waiting).
phaseId =
phaseStatus =
phaseId =
phaseStatus =
...
...
testOutcome It represents the test result: it can be Inconclusive (if the phases already executed were successful) or Fail (if at least one of the executed phases failed).
testState = Testing It can assume one of the following values: not_initialized, idle, initializing, sus-pended, testing, terminating and dis-abled.
LOCK DILNA NAME=RACK:0..7/DILNA:0..7;
278DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805b1082
DILNA
JOB: 100
PC Time&Date: 16:40:38 03/23/2005
NE Time&Date: 16:38:32 09/15/2004
USER NAME: NSN_Frank
COMMAND: Lock DILNA:NAME=RACK:0/DILNA:0;
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: Operation successful
administrativeState = Locked
END OF OUTPUT FOR JOB 100
CHANGED STATE EVENT REPORT:
This provides information about the administrative state, the operational state and the availability status every time a state change occurs:
JOB: 101
PC Time&Date: 16:40:38 03/23/2005
NE Time&Date: 16:38:32 09/15/2004
USER NAME: NSN_Frank
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: Operation successful
CHANGED STATE EVENT REPORT:
NAME = RACK:0/DILNA:0
Administrative State = LOCKED
Notification Identifier = 519
END OF OUTPUT FOR JOB 101
Operation Failed
The specified change of administrative state has not been performed.
Application Guidelines:None.
DN0933412 Issue 01279
BTSplus mainline commands at the Flexi BSC product family
DILNA
Id:0900d805805b1082
Example of Command Execution:Lock DILNA:NAME=RACK:0/DILNA:0;
PERFTEST DILNA
Command Tree:“MANAGED-ELEMENT h BSS-EQUIPMENT h BTSEP h RACK h DILNA h PERFTEST DILNA”
Applicability:Phase 2 and Phase 3.
Visibility level: 1.
Command Description:This command is used to start an asynchronous test in the object.
Long Names:NAME Address of the managed object
System Responses:Operation Completed
Test configuration has been set and the specified test has been started. The System response will not be addressed to the MOT but to the object BTSE.
JOB: 211
PC Time&Date: 12:13:39 03/23/2005
NE Time&Date: 13:15:13 09/15/2004
USER NAME: NSN_Frank
COMMAND: Perftest DILNA:NAME=RACK:0/DILNA:0;
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: Operation successful
MOT = RACK:0/DILNA:0
tO = BTSETEST:1
END OF OUTPUT FOR JOB 211
JOB: 212
PC Time&Date: 12:13:42 03/23/2005
PERFTEST DILNA NAME=RACK:0..7/DILNA:0..7;
280DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805b1082
DILNA
NE Time&Date: 13:15:17 09/15/2004
USER NAME: NSN_Frank
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: Operation successful
ChangedConfigurationNotification:
name = BTSETEST:1
ChangeInfo = created
END OF OUTPUT FOR JOB 212
JOB: 213
PC Time&Date: 12:13:50 03/23/2005
NE Time&Date: 13:15:25 09/15/2004
USER NAME: NSN_Frank
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: Operation successful
CHANGED STATE EVENT REPORT:
NAME = RACK:0/DILNA:0
Operational State = ENABLED
Availability Status = NULL_value
Standby Status = Cold_Standby
Notification Identifier = 168
END OF OUTPUT FOR JOB 213
JOB: 214
PC Time&Date: 12:13:50 03/23/2005
NE Time&Date: 13:15:25 09/15/2004
USER NAME: NSN_Frank
DN0933412 Issue 01281
BTSplus mainline commands at the Flexi BSC product family
DILNA
Id:0900d805805b1082
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: Operation successful
Test Report:
name = BTSETEST:1
testOutcome = PASSED
testTermination = Normal
MOT = RACK:0/DILNA:0
executedPhases =
PreliminaryTestsDilna
SerialEepromTestDilna
EndTestDilna
END OF OUTPUT FOR JOB 214
JOB: 215
PC Time&Date: 12:13:50 03/23/2005
NE Time&Date: 13:15:25 09/15/2004
USER NAME: NSN_Frank
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: Operation successful
ChangedConfigurationNotification:
name = BTSETEST:1
ChangeInfo = deleted
END OF OUTPUT FOR JOB 215
The test results will be displayed at the end of the test phases.
Result TEST:
name = TEST:<n>
testOutcome = This field represents the test result; one of the fol-lowing values can be displayed:
Pass all the test phases are successfully performed.
282DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805b1082
DILNA
Operation Failed
This NACK-message occurs in the following cases: Message cannot be performed, test not supported, capacity restrictions, physical configuration cannot be performed, object not locked.
Application Guidelines:
• In phase 3 MO must be locked previous to the command execution
Example of Command Execution:Perftest DILNA:NAME=RACK:0/DILNA:0;
SET DILNA
Inconclusive the test is aborted by the system or the test is terminated by the opera-tor.
Fail if at least one of the executed phases fail.
mOts = It is the identifier of the hardware object under test.
testTermination = It specifies how the test is terminated, it can assume the following values:
Normal all the test phases are performed.
Abort the test is aborted by system.
Cancel the test is terminated by operator.
executedPhases
phaseId = It represents the list of the executed test phases (in case of successful test result, all the test phases will be listed).
additionalWords =
....
failedPhases
phaseId = It represents the list of the failed test phase; addi-tional information is provided for each phase.phaseId =
....
skippedPhases
phaseId = It represents the list of the skipped phases; they are displayed only for test stopped during it execution.phaseId =
....
poprosedRepair Action =
A list of most probable fail probable causes is shown (max four messages)
SET DILNA NAME=RACK:0..7/DILNA:0..7 [,SCELLNO=] [,WDLNA=];
DN0933412 Issue 01283
BTSplus mainline commands at the Flexi BSC product family
DILNA
Id:0900d805805b1082
Command Tree:“MANAGED-ELEMENT h BSS-EQUIPMENT h BTSEP h RACK h DILNA h SET DILNA”
Applicability:Phase 2 and Phase 3.
Visibility level: 2.
Command Description:This command sets the attributes of the DILNA (Low Noise Amplifier of Diversity Multi-coupler) to the BTSE data base.
Long Names:NAME Address of the managed object
SCELLNO secondCellNumber
WDLNA wiringDataLna
System Responses:Operation Completed
After command execution, a message of Changed Attribute Event Report is displayed. A further message indicates the result of the operation. An example of set command is the following:
JOB: 62
PC Time&Date: 11:57:39 03/23/2005
NE Time&Date: 12:59:14 09/15/2004
USER NAME: NSN_Frank
COMMAND: Set DILNA:NAME=RACK:0/DILNA:0;
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: Operation successful
END OF OUTPUT FOR JOB 62
Operation Failed
The specified attributes have not been set. In addition to the general NACK causes, a specific NACK cause, which indicates that the command is inconsistent with the physical configuration, is possible.
Application Guidelines:
• The DIAMCO_LNA and the CUs are in the same rack and belong to the same cell
• Each CU has a 'normal path' RX input and a 'diversity path' RX input and the operator must indicate which of them is wired to the DIAMCO_LNA
• Wildcard addressing is not possible
284DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805b1082
DILNA
• All CUs which are listed in a previous GET DILNA for WDLNA have to be locked (LOCK CU command) before one of these CUs can be removed from WDLNA. Before locking these CUs first a shutdown of the TRXs related to these CUs should be done
Example of Command Execution:Set DILNA:NAME=RACK:0/DILNA:0,SCELLNO=2,WDLNA=CU0D&CU1D&
CU2D&CU3D;
STOPTEST DILNA
Command Tree:“MANAGED-ELEMENT h BSS-EQUIPMENT h BTSEP h RACK h DILNA h STOPTEST DILNA”
Applicability:Phase 2 and Phase 3.
Visibility level: 1.
Command Description:This command is used to stop a diagnostic previously started.
Long Names:NAME Address of the managed object
System Responses:Operation Completed
Test has been stopped. The System Responses will not be addressed to the MOT but to the object BTSEP.
STOPTEST DILNA NAME=RACK:0..7/DILNA:0..7;
Result TEST:
name = TEST:<n>
testOutcome = inconclusive
mOts = It is the identifier of the hardware object under test.
testTermination = Cancel
executedPhases
phaseId = It represents the list of the executed test phases; the list is not shown for test in the waiting list (queued)....
.
failedPhases
phaseId = It represents the list of the failed test phase;
additional information is provided for each phase.phaseId =
DN0933412 Issue 01285
BTSplus mainline commands at the Flexi BSC product family
DILNA
Id:0900d805805b1082
Operation Failed
Test has not been stopped. This NACK-message can occur when the specified test is not running or in case of test which cannot be stopped.
Application Guidelines:None.
Example of Command Execution:Stoptest DILNA:NAME=RACK:0/DILNA:0;
UNLOCK DILNA
Command Tree:“MANAGED-ELEMENT h BSS-EQUIPMENT h BTSEP h RACK h DILNA h UNLOCK DILNA”
Applicability:Phase 2 and Phase 3.
Visibility level: 1.
Command Description:This command changes the administrative state of the DILNA (Low Noise Amplifier of Diversity Multicoupler).
Long Names:NAME Address of the managed object
System Responses:Operation Completed
The specified change of administrative state has been perfomed:
JOB: 102
PC Time&Date: 16:40:43 03/23/2005
NE Time&Date: 16:38:37 09/15/2004
USER NAME: NSN_Frank
COMMAND: Unlock DILNA:NAME=RACK:0/DILNA:0;
SW RELEASE: 01-04-17-01-26-51_05-02-23
....
skippedPhases
phaseId = It represents the list of the skipped phases;the list is not shown for test in the waiting list (queued).phaseId =
UNLOCK DILNA NAME=RACK:0..7/DILNA:0..7;
286DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805b1082
DILNA
COMMAND RESULT: Operation successful
administrativeState = Unlocked
END OF OUTPUT FOR JOB 102
CHANGED STATE EVENT REPORT:
This provides information about the administrative state, the operational state and the availability status every time a state change occurs:
JOB: 103
PC Time&Date: 16:40:43 03/23/2005
NE Time&Date: 16:38:37 09/15/2004
USER NAME: NSN_Frank
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: Operation successful
CHANGED STATE EVENT REPORT:
NAME = RACK:0/DILNA:0
Administrative State = UNLOCKED
Notification Identifier = 521
END OF OUTPUT FOR JOB 103
Operation Failed
The specified change of administrative state has not been performed.
Application Guidelines:None.
Example of Command Execution:Unlock DILNA:NAME=RACK:0/DILNA:0;
DN0933412 Issue 01287
BTSplus mainline commands at the Flexi BSC product family
DUAMCO
Id:0900d805805b1084
DUAMCOThe DUAMCO object is mainly used to represent the status of the firmware download; the state changes of the DUAMCO object are triggered by subsystems RC, AE and DG as usual.
DUAMCO object is automatically created if an MFDUAMCO is successfully registered.
DELETE DUAMCO
Command Tree:“MANAGED-ELEMENT h BSS-EQUIPMENT h BTSEP h RACK h DUAMCO h DELETE DUAMCO”
Applicability:Phase 2 and Phase 3.
Visibility level: 2.
Command Description:This command deletes the DUAMCO from the BTSE data base.
Automatic deletion is also possible.
Long Names:NAME Address of the managed object
System Responses:Operation Completed
After command execution, a message of Changed Configuration Notification is dis-played. A further message indicates the result of the operation. An example of delete command is the following:
JOB: 71
PC Time&Date: 05.05.2008 11:35:33 +02:00
NE Time&Date: 01.01.1990 00:12:10 +00:00
USER NAME: NSN_Cindy
COMMAND: Delete DUAMCO:NAME=RACK:0/DUAMCO:0;
SW RELEASE: 01-04-19-01-86-MF_08-04-24
COMMAND RESULT:Operation successful.
END OF OUTPUT FOR JOB 71
Operation Failed
None.
Application Guidelines:
• The automatic deletion is not possible when a BCOM/FCOM is inserted in ACOM slot
DELETE DUAMCO NAME=RACK:0..7/DUAMCO:0..5;
288DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805b1084
DUAMCO
Example of Command Execution:DELETE DUAMCO:
NAME=RACK:0/ DUAMCO:0;
GET DUAMCO
Command Tree:“MANAGED-ELEMENT h BSS-EQUIPMENT h BTSEP h RACK h DUAMCO h GET DUAMCO”
Applicability:Phase 2 and Phase 3.
Visibility level: 0.
Command Description:This command displays the attributes of DUAMCO object.
Long Names:NAME Address of the managed object
REQATTL Required attribute list
ALS alarmStatus
AST administrativeState
AVS availabilityStatus
OST operationalState
PRS proceduralStatus
DMCFWID duamcoFwId
RELFUNCOBJ relatedFuncObjects
System Responses:Operation Completed
A message indicates the result of the operation. An example of get command is the fol-lowing:
JOB: 86
PC Time&Date: 05.05.2008 11:35:48 +02:00
NE Time&Date: 01.01.1990 00:12:25 +00:00
USER NAME: NSN_Cindy
COMMAND: Get DUAMCO:NAME=RACK:0/DUAMCO:0;
SW RELEASE: 01-04-19-01-86-MF_08-04-24
COMMAND RESULT:Operation successful
alarmStatus = CLEARED
administrativeState = Unlocked
GET DUAMCO NAME=RACK:0..7/DUAMCO:0..5 [,REQATTL=ALS, AST, AVS, OST, PRS, DMCFWID, RELFUNCOBJ];
DN0933412 Issue 01289
BTSplus mainline commands at the Flexi BSC product family
DUAMCO
Id:0900d805805b1084
availabilityStatus = NULL
operationalState = ENABLED
proceduralStatus = NULL
duamcoFwId = "BFDU0250.SWI:00-50-19-02-15-00_08-01-01"
relatedFuncObjects = Null
END OF OUTPUT FOR JOB 86
Operation Failed
None.
Application Guidelines:None.
Example of Command Execution:GetDU-AMCO:NAME=RACK:0/DUAMCO:0,REQATTL=ALS&AST&AVS&OST&PRS&DMCF-WID&RELFUNCOBJ;
GETTEST DUAMCO
Command Tree:“MANAGED-ELEMENT h BSS-EQUIPMENT h BTSEP h RACK h DUAMCO h GETTEST DUAMCO”
Applicability:Phase 2 and Phase 3.
Visibility level: 0.
Command Description:This command displays the attributes of the object test.
Long Names:NAME Address of the managed object
REQATTL Required attribute list
System Responses:Operation Completed
None.
Operation Failed
None.
Application Guidelines:None.
GETTEST DUAMCO NAME=RACK:0..7/DUAMCO:0..5;
290DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805b1084
DUAMCO
Example of Command Execution:Gettest DUAMCO:NAME=RACK:0/DUAMCO:0,REQATTL=MORT&TESTMON&TES-TOUT& TESTST;.
LOCK DUAMCO
Command Tree:“MANAGED-ELEMENT h BSS-EQUIPMENT h BTSEP h RACK h DUAMCO h LOCK DUAMCO”
Applicability:Phase 2 and Phase 3.
Visibility level: 1.
Command Description:This command changes the administrative state of DUAMCO.
Long Names:NAME Address of the managed object
System Responses:Operation Completed
After command execution, a message of Changed Configuration Notification is dis-played. A further message indicates the result of the operation. An example of Lock command is the following:
JOB: 99
PC Time&Date: 05.05.2008 11:36:17 +02:00.
NE Time&Date: 01.01.1990 00:12:54 +00:00
USER NAME: NSN_Cindy
COMMAND: Lock DUAMCO:NAME=RACK:0/DUAMCO:0;
SW RELEASE: 01-04-19-01-86-MF_08-04-24
COMMAND RESULT:Operation successful
administrativeState = Locked
END OF OUTPUT FOR JOB 99
Operation Failed
None.
Application Guidelines:None.
Example of Command Execution:Lock DUAMCO:NAME=RACK:0/DUAMCO:0, AST=“Locked”;
LOCK DUAMCO NAME=RACK:0..7/DUAMCO:0..5;
DN0933412 Issue 01291
BTSplus mainline commands at the Flexi BSC product family
DUAMCO
Id:0900d805805b1084
PERFTEST DUAMCO
Command Tree:“MANAGED-ELEMENT h BSS-EQUIPMENT h BTSEP h RACK h DUAMCO h PERFTEST DUAMCO”
Applicability:Phase 2 and Phase 3.
Visibility level: 1.
Command Description:This command is used to start an asynchronous test in the object.
Long Names:NAME Address of the managed object
System Responses:Operation Completed
After command execution, a message of Changed Configuration Notification is dis-played. A further message indicates the result of the operation. An example of perftest command is the following:
JOB: 138.
PC Time&Date: 05.05.2008 11:36:42 +02:00
NE Time&Date: 01.01.1990 00:13:19 +00:00
USER NAME: NSN_Cindy
COMMAND: Perftest DUAMCO:NAME=RACK:0/DUAMCO:0;
SW RELEASE: 01-04-19-01-86-MF_08-04-24
COMMAND RESULT:Operation successful
MOT = RACK:0/DUAMCO:0
tO = BTSETEST:1
END OF OUTPUT FOR JOB 138
Operation Failed
None.
Application Guidelines:None.
Example of Command Execution:Perftest DUAMCO:NAME=RACK:0/DUAMCO:0;
STOPTEST DUAMCO
PERFTEST DUAMCO NAME=RACK:0..7/DUAMCO:0..5;
STOPTEST DUAMCO NAME=RACK:0..7/DUAMCO:0..5;
292DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805b1084
DUAMCO
Command Tree:“MANAGED-ELEMENT h BSS-EQUIPMENT h BTSEP h RACK h DUAMCO h STOPTEST DUAMCO”
Applicability:Phase 2 and Phase 3.
Visibility level: 1.
Command Description:This command is used to interrupt a running asynchronous test in the object.
Long Names:NAME Address of the managed object
System Responses:Operation Completed
None.
Operation Failed
None.
Application Guidelines:None.
Example of Command Execution:Stoptest DUAMCO:NAME=RACK:0/DUAMCO:0;
UNLOCK DUAMCO
Command Tree:“MANAGED-ELEMENT h BSS-EQUIPMENT h BTSEP h RACK h DUAMCO h UNLOCK DUAMCO”
Applicability:Phase 2 and Phase 3.
Visibility level: 1.
Command Description:This command changes the administrative state of DUAMCO.
Long Names:NAME Address of the managed object
System Responses:Operation Completed
After command execution, a message of Changed Configuration Notification is dis-played. A further message indicates the result of the operation. An example of unlock command is the following:
UNLOCK DUAMCO NAME=RACK:0..7/DUAMCO:0..5;
DN0933412 Issue 01293
BTSplus mainline commands at the Flexi BSC product family
DUAMCO
Id:0900d805805b1084
JOB: 108
PC Time&Date: 05.05.2008 11:36:35 +02:00
NE Time&Date: 01.01.1990 00:13:12 +00:00
USER NAME: NSN_Cindy
COMMAND: Unlock DUAMCO:NAME=RACK:0/DUAMCO:0;
SW RELEASE: 01-04-19-01-86-MF_08-04-24
COMMAND RESULT:Operation successful
administrativeState = Unlocked.
Operation Failed
None.
Application Guidelines:None.
Example of Command Execution:Unlock DUAMCO:NAME=RACK:0/DUAMCO:0, AST=“Unlocked”;
294DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805b1087
DUDCTMA
DUDCTMAThe DUDCTMA object represents the power supply module of a TMA (Tower Mounted Amplifier) connected to DUAMCO.
CREATE DUDCTMA
Command Tree:“MANAGED-ELEMENT h BSS-EQUIPMENT h BTSEP h RACK h DUDCTMA h CREATE DUDCTMA”
Applicability:Phase 2 and Phase 3.
Visibility level: 2.
Command Description:This command adds the DUAMCO_DC_TMA (DC Power Supply Module of TMA) to the BTSE data base.
Long Names:NAME Address of the managed object
System Responses:Operation Completed
After command execution, a message of Changed Configuration Notification is dis-played. A further message indicates the result of the operation. An example of create command is the following:
JOB: 78
PC Time&Date: 16:38:29 03/23/2005
NE Time&Date: 16:36:23 09/15/2004
USER NAME: NSN
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: Operation successful
ChangedConfigurationNotification:
name = RACK:0/DUDCTMA:0
ChangeInfo = created
END OF OUTPUT FOR JOB 78
CREATE DUDCTMA NAME=RACK:0..7/DUDCTMA:0..11;
DN0933412 Issue 01295
BTSplus mainline commands at the Flexi BSC product family
DUDCTMA
Id:0900d805805b1087
JOB: 79
PC Time&Date: 16:38:29 03/23/2005
NE Time&Date: 16:36:23 09/15/2004
USER NAME: NSN
COMMAND: Create DUDCTMA:NAME=RACK:0/DUDCTMA:0;
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: Operation successful
END OF OUTPUT FOR JOB 79
Operation Failed
The specified Object has not been created. In addition to the general NACK causes, a specific NACK cause, which indicates that the command is inconsistent with the physical configuration, is possible. An example is the following:
JOB: 75
PC Time&Date: 16:37:54 03/23/2005
NE Time&Date: 16:35:47 09/15/2004
USER NAME: NSN
COMMAND: Create DUDCTMA:NAME=RACK:0/DUDCTMA:0;
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: OPERATION FAILED
Message cannot be performed (-17)
END OF OUTPUT FOR JOB 75
Application Guidelines:None.
Example of Command Execution:Create DUDCTMA:NAME=RACK:0/DUDCTMA:0;
DELETE DUDCTMADELETE DUDCTMA NAME=RACK:0..7/DUDCTMA:0..11;
296DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805b1087
DUDCTMA
Command Tree:“MANAGED-ELEMENT h BSS-EQUIPMENT h BTSEP h RACK h DUDCTMA h DELETE DUDCTMA”
Applicability:Phase 2 and Phase 3.
Visibility level: 2.
Command Description:This command deletes the DUAMCO_DC_TMA (DC Power Supply Module of TMA) from the BTSE data base.
Long Names:NAME Address of the managed object
System Responses:Operation Completed
After command execution, a message of Changed Configuration Notification is dis-played. A further message indicates the result of the operation. An example of delete command is the following:
JOB: 90
PC Time&Date: 16:39:22 03/23/2005
NE Time&Date: 16:37:16 09/15/2004
USER NAME: NSN
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: Operation successful
ChangedConfigurationNotification:
name = RACK:0/DUDCTMA:0
ChangeInfo = deleted
END OF OUTPUT FOR JOB 90
JOB: 91
PC Time&Date: 16:39:22 03/23/2005
NE Time&Date: 16:37:16 09/15/2004
USER NAME: NSN
DN0933412 Issue 01297
BTSplus mainline commands at the Flexi BSC product family
DUDCTMA
Id:0900d805805b1087
COMMAND: Delete DUDCTMA:NAME=RACK:0/DUDCTMA:0;
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: Operation successful
END OF OUTPUT FOR JOB 91
Operation Failed
The specified Object has not been deleted. Additionally to the general NACK causes, a specific NACK cause, meaning that the command is inconsistent with physical configu-ration, is possible.
Application Guidelines:
• DUDCTMA must be locked in phase 3 before deletion
Example of Command Execution:Delete DUDCTMA:NAME=RACK:0/DUDCTMA:0;
GET DUDCTMA
Command Tree:“MANAGED-ELEMENT h BSS-EQUIPMENT h BTSEP h RACK h DUDCTMA h GET DUDCTMA”
Applicability:Phase 2 and Phase 3.
Visibility level: 0.
Command Description:This command displays the attributes of the DUAMCO_DC_TMA (DC Power Supply Module of TMA).
Long Names:NAME Address of the managed object
REQATTL Required attribute list
ALS alarmStatus
AST administrativeState
AVS availabilityStatus
OST operationalState
PRS proceduralStatus
RELFUNCOBJ relatedFuncObjects
System Responses:Operation Completed
GET DUDCTMA NAME=RACK:0..7/DUDCTMA:0..11 [,REQATTL=ALS, AST, AVS, OST, PRS, RELFUNCOBJ];
298DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805b1087
DUDCTMA
After command execution, a message of Changed Configuration Notification is dis-played. A further message indicates the result of the operation. An example of get command is the following:
JOB: 82
PC Time&Date: 16:38:53 03/23/2005
NE Time&Date: 16:36:47 09/15/2004
USER NAME: NSN
COMMAND: Get DUDCTMA:NAME=RACK:0/DUDCTMA:0;
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: Operation successful
alarmStatus = CLEARED
administrativeState = Unlocked
availabilityStatus = NULL
operationalState = ENABLED
proceduralStatus = NULL
relatedFuncObjects =
END OF OUTPUT FOR JOB 82
Operation Failed
The GET command has not been successfully executed. A general NACK will indicate possible errors or a specific NACK strictly related to the single command is possible.
Application Guidelines:None.
Example of Command Execution:Get DUDCTMA:NAME=RACK:0/DUDCTMA:0,REQATTL=ALS&AST&AVS&
OST&PRS&RELFUNCOBJ;
GETTEST DUDCTMA
Command Tree:“MANAGED-ELEMENT h BSS-EQUIPMENT h BTSEP h RACK h DUDCTMA h GETTEST DUDCTMA”
Applicability:Phase 2 and Phase 3.
Visibility level: 0.
GETTEST DUDCTMA NAME=RACK:0..7/DUDCTMA:0..11;
DN0933412 Issue 01299
BTSplus mainline commands at the Flexi BSC product family
DUDCTMA
Id:0900d805805b1087
Command Description:This command displays the attributes of the object test.
Long Names:NAME Address of the managed object
REQATTL Required attribute list
System Responses:Operation Completed
After command execution, a message of Changed Configuration Notification is dis-played. A further message indicates the result of the operation. An example of gettest command is the following:
JOB: 216
PC Time&Date: 12:13:57 03/23/2005
NE Time&Date: 13:15:32 09/15/2004
USER NAME: NSN
COMMAND: Gettest DUDCTMA:NAME=RACK:0/DUDCTMA:0;
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: Operation successful
MOT = RACK:0/DUDCTMA:0
testMonitor =
phaseId = PreliminaryTestsDudctma
phaseStatus = Running
phaseId = CheckAlarmStatusDudctma
phaseStatus = Waiting
phaseId = EndTestDudctma
phaseStatus = Waiting
testOutcome = INCONCLUSIVE
testState = INITIALIZING
END OF OUTPUT FOR JOB 216
Operation Failed
The GET command has not been successfully executed. A general NACK will indicate possible errors or a specific NACK strictly related to the single command is possible.
300DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805b1087
DUDCTMA
Application Guidelines:None.
Example of Command Execution:Gettest DUDCTMA:NAME=RACK:0/DUDCTMA:0;
LOCK DUDCTMA
Command Tree:“MANAGED-ELEMENT h BSS-EQUIPMENT h BTSEP h RACK h DUDCTMA h LOCK DUDCTMA”
Applicability:Phase 2 and Phase 3.
Visibility level: 1.
Command Description:This command changes the administrative state of DUAMCO_DC_TMA (DC Power Supply Module of TMA).
Long Names:NAME Address of the managed object
System Responses:Operation Completed
The specified change of administrative state has been perfomed:
testMonitor it is a list of all test phases related to the selected object; for each phase the related phaseStatus is provided (Passed, Failed, Running or Waiting).
phaseId =
phaseStatus =
phaseId =
phaseStatus =
...
...
testOutcome It represents the test result: it can be Inconclusive (if the phases already executed were successful) or Fail (if at least one of the executed phases failed).
testState = Testing It can assume one of the following values: not_initialized, idle, initializing, sus-pended, testing, terminating and dis-abled.
LOCK DUDCTMA NAME=RACK:0..7/DUDCTMA:0..11;
DN0933412 Issue 01301
BTSplus mainline commands at the Flexi BSC product family
DUDCTMA
Id:0900d805805b1087
JOB: 83
PC Time&Date: 16:38:58 03/23/2005
NE Time&Date: 16:36:52 09/15/2004
USER NAME: NSN
COMMAND: Lock DUDCTMA:NAME=RACK:0/DUDCTMA:0;
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: Operation successful
administrativeState = Locked
END OF OUTPUT FOR JOB 83
CHANGED STATE EVENT REPORT:
This provides information about the administrative state, the operational state and the availability status every time a state change occurs:
JOB: 84
PC Time&Date: 16:38:58 03/23/2005
NE Time&Date: 16:36:52 09/15/2004
USER NAME: NSN
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: Operation successful
CHANGED STATE EVENT REPORT:
NAME = RACK:0/DUDCTMA:0
Administrative State = LOCKED
Notification Identifier = 511
END OF OUTPUT FOR JOB 84
Operation Failed
The specified change of administrative state has not been performed.
Application Guidelines:None.
302DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805b1087
DUDCTMA
Example of Command Execution:Lock DUDCTMA:NAME=RACK:0/DUDCTMA:0;
PERFTEST DUDCTMA
Command Tree:“MANAGED-ELEMENT h BSS-EQUIPMENT h BTSEP h RACK h DUDCTMA h PERFTEST DUDCTMA”
Applicability:Phase 2 and Phase 3.
Visibility level: 1.
Command Description:This command is used to start an asynchronous test in the object.
Long Names:NAME Address of the managed object
System Responses:Operation Completed
Test configuration has been set and the specified test has been started. The System response will not be addressed to the MOT but to the object BTSEP.
JOB: 216
PC Time&Date: 12:13:57 03/23/2005
NE Time&Date: 13:15:32 09/15/2004
USER NAME: NSN
COMMAND: Perftest DUDCTMA:NAME=RACK:0/DUDCTMA:0;
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: Operation successful
MOT = RACK:0/DUDCTMA:0
tO = BTSETEST:2
END OF OUTPUT FOR JOB 216
JOB: 217
PC Time&Date: 12:13:58 03/23/2005
PERFTEST DUDCTMA NAME=RACK:0..7/DUDCTMA:0..11;
DN0933412 Issue 01303
BTSplus mainline commands at the Flexi BSC product family
DUDCTMA
Id:0900d805805b1087
NE Time&Date: 13:15:33 09/15/2004
USER NAME: NSN
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: Operation successful
ChangedConfigurationNotification:
name = BTSETEST:2
ChangeInfo = created
END OF OUTPUT FOR JOB 217
JOB: 218
PC Time&Date: 12:13:58 03/23/2005
NE Time&Date: 13:15:33 09/15/2004
USER NAME: NSN
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: Operation successful
CHANGED STATE EVENT REPORT:
NAME = RACK:0/DUDCTMA:0
Operational State = ENABLED
Availability Status = NULL_value
Standby Status = Cold_Standby
Notification Identifier = 256
END OF OUTPUT FOR JOB 218
JOB: 219
PC Time&Date: 12:13:58 03/23/2005
NE Time&Date: 13:15:33 09/15/2004
USER NAME: NSN
SW RELEASE: 01-04-17-01-26-51_05-02-23
304DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805b1087
DUDCTMA
COMMAND RESULT: Operation successful
Test Report:
name = BTSETEST:2
testOutcome = PASSED
testTermination = Normal
MOT = RACK:0/DUDCTMA:0
executedPhases =
PreliminaryTestsDudctma
BootEepromTestDudctma
SerialEepromTestDudctma
EndTestDudctma
END OF OUTPUT FOR JOB 219
JOB: 220
PC Time&Date: 12:13:58 03/23/2005
NE Time&Date: 13:15:33 09/15/2004
USER NAME: NSN
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: Operation successful
ChangedConfigurationNotification:
name = BTSETEST:2
ChangeInfo = deleted
END OF OUTPUT FOR JOB 220
The test results will be displayed at the end of the test phases.
Result TEST:
name = TEST:<n>
testOutcome = This field represents the test result; one of the fol-lowing values can be displayed:
Pass all the test phases are successfully performed.
DN0933412 Issue 01305
BTSplus mainline commands at the Flexi BSC product family
DUDCTMA
Id:0900d805805b1087
Operation Failed
This NACK-message occurs in the following cases: Message cannot be performed, test not supported, capacity restrictions, physical configuration cannot be performed, object not locked.
Application Guidelines:
• In phase 3 MO must be locked previous to the command execution
Example of Command Execution:Perftest DUDCTMA:NAME=RACK:0/DUDCTMA:0;
STOPTEST DUDCTMA
Inconclusive the test is aborted by the system or the test is terminated by the opera-tor.
Fail if at least one of the executed phases fail.
mOts = It is the identifier of the hardware object under test.
testTermination = It specifies how the test is terminated, it can assume the following values:
Normal all the test phases are performed.
Abort the test is aborted by system.
Cancel the test is terminated by operator.
executedPhases
phaseId = It represents the list of the executed test phases (in case of successful test result, all the test phases will be listed).
additionalWords =
....
failedPhases
phaseId = It represents the list of the failed test phase; addi-tional information is provided for each phase.phaseId =
....
skippedPhases
phaseId = It represents the list of the skipped phases; they are displayed only for test stopped during it execution.phaseId =
....
poprosedRepair Action =
A list of most probable fail probable causes is shown (max four messages)
STOPTEST DUDCTMA NAME=RACK:0..7/DUDCTMA:0..11;
306DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805b1087
DUDCTMA
Command Tree:“MANAGED-ELEMENT h BSS-EQUIPMENT h BTSEP h RACK h DUDCTMA h STOPTEST DUDCTMA”
Applicability:Phase 2 and Phase 3.
Visibility level: 1.
Command Description:This command is used to stop a diagnostic previously started.
Long Names:NAME Address of the managed object
System Responses:Operation Completed
Test has been stopped. The System Responses will not be addressed to the MOT but to the object BTSEP.
Operation Failed
Test has not been stopped. This NACK-message can occur when the specified test is not running or in case of test which cannot be stopped.
Application Guidelines:None.
Result TEST:
name = TEST:<n>
testOutcome = inconclusive
mOts = It is the identifier of the hardware object under test.
testTermination = Cancel
executedPhases
phaseId = It represents the list of the executed test phases; the list is not shown for test in the waiting list (queued)....
.
failedPhases
phaseId = It represents the list of the failed test phase;
additional information is provided for each phase.phaseId =
....
skippedPhases
phaseId = It represents the list of the skipped phases;the list is not shown for test in the waiting list (queued).phaseId =
DN0933412 Issue 01307
BTSplus mainline commands at the Flexi BSC product family
DUDCTMA
Id:0900d805805b1087
Example of Command Execution:Stoptest DUDCTMA:NAME=RACK:0/DUDCTMA:0;
UNLOCK DUDCTMA
Command Tree:“MANAGED-ELEMENT h BSS-EQUIPMENT h BTSEP h RACK h DUDCTMA h UNLOCK DUDCTMA”
Applicability:Phase 2 and Phase 3.
Visibility level: 1.
Command Description:This command changes the administrative state of DUAMCO_DC_TMA (DC Power Supply Module of TMA).
Long Names:NAME Address of the managed object
System Responses:Operation Completed
The specified change of administrative state has been perfomed:
JOB: 85
PC Time&Date: 16:39:03 03/23/2005
NE Time&Date: 16:36:57 09/15/2004
USER NAME: NSN
COMMAND: Unlock DUDCTMA:NAME=RACK:0/DUDCTMA:0;
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: Operation successful
administrativeState = Unlocked
END OF OUTPUT FOR JOB 85
CHANGED STATE EVENT REPORT:
This provides information about the administrative state, the operational state and the availability status every time a state change occurs:
UNLOCK DUDCTMA NAME=RACK:0..7/DUDCTMA:0..11;
308DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805b1087
DUDCTMA
JOB: 86
PC Time&Date: 16:39:03 03/23/2005
NE Time&Date: 16:36:57 09/15/2004
USER NAME: NSN
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: Operation successful
CHANGED STATE EVENT REPORT:
NAME = RACK:0/DUDCTMA:0
Administrative State = UNLOCKED
Notification Identifier = 512
END OF OUTPUT FOR JOB 86
Operation Failed
The specified change of administrative state has not been performed.
Application Guidelines:None.
Example of Command Execution:Unlock DUDCTMA:NAME=RACK:0/DUDCTMA:0;
DN0933412 Issue 01309
BTSplus mainline commands at the Flexi BSC product family
DULNA
Id:0900d805805b1089
DULNAThe DULNA object represents the low noise amplifier of DUAMCO (Dual Antenna Mul-ticoupler) or FDUAMCO.
CREATE DULNA
Command Tree:“MANAGED-ELEMENT h BSS-EQUIPMENT h BTSEP h RACK h DULNA h CREATE DULNA”
Applicability:Phase 2 and Phase 3.
Visibility level: 2.
Command Description:This command adds the DULNA (Low Noise Amplifier of Duplex Antenna Multicoupler) together with its attributes to the BTSE data base.
Long Names:NAME Address of the managed object
CELLNO cellNumber
COMBMD combMode
LNAMDB lnaModeDb
LNAPRED lnaPredecessor
SCELLNO secondCellNumber
WDLNA wiringDataLna
GNADB gainAdjustDb
System Responses:Operation Completed
After command execution, a message of Changed Configuration Notification is dis-played. A further message indicates the result of the operation. An example of create command is the following:
JOB: 92
PC Time&Date: 11:59:23 03/23/2005
NE Time&Date: 13:00:58 09/15/2004
USER NAME: NSN
CREATE DULNA NAME=RACK:0..7/DULNA:0..11 ,CELLNO= ,COMBMD= [,LNAMDB=] [,LNAPRED=] [,SCELLNO=] ,WDLNA= [,GNADB=];
310DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805b1089
DULNA
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: Operation successful
ChangedConfigurationNotification:
name = RACK:0/DULNA:0
ChangeInfo = created
END OF OUTPUT FOR JOB 92
JOB: 93
PC Time&Date: 11:59:23 03/23/2005
NE Time&Date: 13:00:58 09/15/2004
USER NAME: NSN
COMMAND: Create DULNA:NAME=RACK:0/DULNA:0,CELLNO=0,COMBMD=One-ToOne,WDLNA=CU0N;
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: Operation successful
cellNumber = 0
combMode = OneToOne
secondCellNumber = 2
wiringDataLna = CU0N
END OF OUTPUT FOR JOB 93
Operation Failed
The specified Object has not been created. In addition to the general NACK causes, a specific NACK cause, which indicates that the command is inconsistent with the physical configuration, is possible. An example is the following:
JOB: 94
PC Time&Date: 11:59:23 03/23/2005
NE Time&Date: 13:00:58 09/15/2004
USER NAME: NSN
COMMAND: Create DULNA:NAME=RACK:0/DULNA:2;
DN0933412 Issue 01311
BTSplus mainline commands at the Flexi BSC product family
DULNA
Id:0900d805805b1089
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: OPERATION FAILED
Object instance unknown (-9)
END OF OUTPUT FOR JOB 94
Application Guidelines:
• One DUAMCO contains two DUAMCO_LNA. The first DUAMCO within the rack is put in the first slot, the second DUAMCO in the second slot and so on. This means that DUAMCO_LNA 0 and DUAMCO_LNA 1 are always physically located in the first slot within the rack, the DUAMCO_LNA 2 and DUAMCO_LNA 3 in the second slot and so on
• The DUAMCO_LNA and the CUs must be in the same rack and must belong to the same cell
• Each CU has a 'normal path' RX input and a 'diversity path' RX input and the operator must indicate which of them is wired to the DUAMCO_LNA
• If there is no wiring the operator must not provide a value for the attribute LNAPRED (if a get is done the attribute identifier will be put into the list of unavailable attributes)
• If there is no wiring for the attribute LNAPRED and the operator enters a value, this error can be corrected by a deletion of the object and a re-creation of the object
• The BTSE SW doesn't check if the entered "predecessor (relative number)" is com-patible with typeOfBTSE; e.g. an input of TMA 11 is not rejected in a BS40 although BS40 allows only the creation of TMA 0-5
The BTSE SW doesn't check if the entered "predecessor (rack)" is compatible with typeOfBTSE; e.g. an input of RACK 1 is not rejected in a BS40 although BS40 allows only the creation of RACK 0
• Wildcard addressing is not possible
Example of Command Execution:Create DULNA:NAME=RACK:1/DULNA:0,CELLNO=0,COMBMD=FourToOne,
SCELLNO=2,WDLNA=CU0N&CU1N&CU2N&CU3N,LNAPRED=DULNA-RACK0-0;
DELETE DULNA
Command Tree:“MANAGED-ELEMENT h BSS-EQUIPMENT h BTSEP h RACK h DULNA h DELETE DULNA”
Applicability:Phase 2 and Phase 3.
Visibility level: 2.
DELETE DULNA NAME=RACK:0..7/DULNA:0..11;
312DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805b1089
DULNA
Command Description:This command deletes the DULNA (Low Noise Amplifier of Duplex Antenna Multicou-pler) together with its attributes from the BTSE data base.
Long Names:NAME Address of the managed object
System Responses:Operation Completed
After command execution, a message of Changed Configuration Notification is dis-played. A further message indicates the result of the operation. An example of delete command is the following:
JOB: 86
PC Time&Date: 11:58:47 03/23/2005
NE Time&Date: 13:00:22 09/15/2004
USER NAME: NSN
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: Operation successful
ChangedConfigurationNotification:
name = RACK:0/DULNA:0
ChangeInfo = deleted
END OF OUTPUT FOR JOB 86
JOB: 87
PC Time&Date: 11:58:47 03/23/2005
NE Time&Date: 13:00:22 09/15/2004
USER NAME: NSN
COMMAND: Delete DULNA:NAME=RACK:0/DULNA:0;
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: Operation successful
END OF OUTPUT FOR JOB 87
Operation Failed
DN0933412 Issue 01313
BTSplus mainline commands at the Flexi BSC product family
DULNA
Id:0900d805805b1089
The specified Object has not been deleted. Additionally to the general NACK causes, a specific NACK cause, meaning that the command is inconsistent with physical configu-ration, is possible.
Application Guidelines:
• DULNA must be locked in Phase 3, before deletion
• If this object is deleted, the related TRXs are out of service
Example of Command Execution:Delete DULNA:NAME=RACK:0/DULNA:0;
GET DULNA
Command Tree:“MANAGED-ELEMENT h BSS-EQUIPMENT h BTSEP h RACK h DULNA h GET DULNA”
Applicability:Phase 2 and Phase 3.
Visibility level: 0.
Command Description:This command displays the attributes of the DULNA (Low Noise Amplifier of Duplex Antenna Multicoupler).
Long Names:NAME Address of the managed object
REQATTL Required attribute list
ALS alarmStatus
AST administrativeState
AVS availabilityStatus
CELLNO cellNumber
GNA gainAdjust(dB)
COMBMD combMode
LNAMDB lnaModeDb
LNAMODE lnaMode
LNAPRED lnaPredecessor
OST operationalState
PRS proceduralStatus
RELFUNCOBJ relatedFuncObjects
SCELLNO secondCellNumber
GET DULNA NAME=RACK:0..7/DULNA:0..11 [,REQATTL=ALS, AST, AVS, CELLNO, GNA, COMBMD, LNAMDB, LNAMODE, LNAPRED, OST, PRS, RELFUNCOBJ, SCELLNO, WDLNA, GNADB];
314DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805b1089
DULNA
WDLNA wiringDataLna
GNADB gainAdjustDb
System Responses:Operation Completed
After command execution, a message of Changed Configuration Notification is dis-played. A further message indicates the result of the operation. An example of get command is the following:
JOB: 63
PC Time&Date: 11:58:17 03/23/2005
NE Time&Date: 12:59:52 09/15/2004
USER NAME: NSN
COMMAND: Get DULNA:NAME=RACK:0/DULNA:0;
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: Operation successful
alarmStatus = CLEARED
administrativeState = Unlocked
availabilityStatus = NULL
cellNumber = 0
cableLossAdjust(dB) = N_00
combMode = OneToOne
lnaMode = AMCO_MODE
lnaPredecessor = Null
operationalState = ENABLED
proceduralStatus = NULL
relatedFuncObjects =
secondCellNumber = NotUsed
wiringDataLna = CU1
END OF OUTPUT FOR JOB 63
Operation Failed
The GET command has not been successfully executed. A general NACK will indicate possible errors or a specific NACK strictly related to the single command is possible.
DN0933412 Issue 01315
BTSplus mainline commands at the Flexi BSC product family
DULNA
Id:0900d805805b1089
Application Guidelines:
• The value for the attribute relatedFuncObjects in LMT Evolution Phase 2 is "not con-figured"
• The value for proceduralStatus must be NULL
Example of Command Execution:Get DULNA:NAME=RACK:0/DULNA:0,REQATTL=ALS&AST&AVS&CELLNO&
CLADJ&COMBMD&RELFUNCOBJ&LNAMODE&LNAPRED&OST&PRS&SCELLNO&
WDLNA;
GETTEST DULNA
Command Tree:“MANAGED-ELEMENT h BSS-EQUIPMENT h BTSEP h RACK h DULNA h GETTEST DULNA”
Applicability:Phase 2 and Phase 3.
Visibility level: 0.
Command Description:This command displays the attributes of the object test.
Long Names:NAME Address of the managed object
REQATTL Required attribute list
System Responses:Operation Completed
After command execution, a message of Changed Configuration Notification is dis-played. A further message indicates the result of the operation. An example of getest command is the following:
JOB: 72
PC Time&Date: 11:58:33 03/23/2005
NE Time&Date: 13:00:08 09/15/2004
USER NAME: NSN
COMMAND: Gettest DULNA:NAME=RACK:0/DULNA:0;
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: Operation successful
GETTEST DULNA NAME=RACK:0..7/DULNA:0..11;
316DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805b1089
DULNA
MOT = RACK:0/DULNA:0
testMonitor =
phaseId = PreliminaryTestsDulna
phaseStatus = Running
phaseId = CheckAlarmStatusDulna
phaseStatus = Waiting
phaseId = EndTestDulna
phaseStatus = Waiting
testOutcome = INCONCLUSIVE
testState = INITIALIZING
END OF OUTPUT FOR JOB 72
Operation Failed
The GET command has not been successfully executed. A general NACK will indicate possible errors or a specific NACK strictly related to the single command is possible.
Application Guidelines:None.
Example of Command Execution:Gettest DULNA:NAME=RACK:0/DULNA:0;
LOCK DULNA
testMonitor it is a list of all test phases related to the selected object; for each phase the related phaseStatus is provided (Passed, Failed, Running or Waiting).
phaseId =
phaseStatus =
phaseId =
phaseStatus =
...
...
testOutcome It represents the test result: it can be Inconclusive (if the phases already executed were successful) or Fail (if at least one of the executed phases failed).
testState = Testing It can assume one of the following values: not_initialized, idle, initializing, sus-pended, testing, terminating and dis-abled.
LOCK DULNA NAME=RACK:0..7/DULNA:0..11;
DN0933412 Issue 01317
BTSplus mainline commands at the Flexi BSC product family
DULNA
Id:0900d805805b1089
Command Tree:“MANAGED-ELEMENT h BSS-EQUIPMENT h BTSEP h RACK h DULNA h LOCK DULNA”
Applicability:Phase 2 and Phase 3.
Visibility level: 1.
Command Description:This command changes the administrative state of DULNA (Low Noise Amplifier of Duplex Antenna Multicoupler).
Long Names:NAME Address of the managed object
System Responses:Operation Completed
The specified change of administrative state has been perfomed:
JOB: 73
PC Time&Date: 11:58:33 03/23/2005
NE Time&Date: 13:00:08 09/15/2004
USER NAME: NSN
COMMAND: Lock DULNA:NAME=RACK:0/DULNA:0;
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: Operation successful
administrativeState = Locked
END OF OUTPUT FOR JOB 73
CHANGED STATE EVENT REPORT:
This provides information about the administrative state, the operational state and the availability status every time a state change occurs:
JOB: 74
PC Time&Date: 11:58:33 03/23/2005
NE Time&Date: 13:00:08 09/15/2004
318DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805b1089
DULNA
USER NAME: NSN
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: Operation successful
CHANGED STATE EVENT REPORT:
NAME = RACK:0/DULNA:0
Administrative State = LOCKED
Notification Identifier = 301
END OF OUTPUT FOR JOB 74
Operation Failed
The specified change of administrative state has not been performed.
Application Guidelines:None.
Example of Command Execution:Lock DULNA:NAME=RACK:0/DULNA:0;
PERFTEST DULNA
Command Tree:“MANAGED-ELEMENT h BSS-EQUIPMENT h BTSEP h RACK h DULNA h PERFTEST DULNA”
Applicability:Phase 2 and Phase 3.
Visibility level: 1.
Command Description:This command is used to start an asynchronous test in the object.
Long Names:NAME Address of the managed object
System Responses:Operation Completed
Test configuration has been set and the specified test has been started. The System response will not be addressed to the MOT but to the object BTSEP.
JOB: 77
PERFTEST DULNA NAME=RACK:0..7/DULNA:0..11;
DN0933412 Issue 01319
BTSplus mainline commands at the Flexi BSC product family
DULNA
Id:0900d805805b1089
PC Time&Date: 11:58:39 03/23/2005
NE Time&Date: 13:00:14 09/15/2004
USER NAME: NSN
COMMAND: Perftest DULNA:NAME=RACK:0/DULNA:0;
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: Operation successful
MOT = RACK:0/DULNA:0
tO = BTSETEST:4
END OF OUTPUT FOR JOB 77
JOB: 78
PC Time&Date: 11:58:39 03/23/2005
NE Time&Date: 13:00:14 09/15/2004
USER NAME: NSN
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: Operation successful
ChangedConfigurationNotification:
name = BTSETEST:4
ChangeInfo = created
END OF OUTPUT FOR JOB 78
JOB: 79
PC Time&Date: 11:58:39 03/23/2005
NE Time&Date: 13:00:14 09/15/2004
USER NAME: NSN
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: Operation successful
CHANGED STATE EVENT REPORT:
320DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805b1089
DULNA
NAME = RACK:0/DULNA:0
Operational State = ENABLED
Availability Status = NULL_value
Notification Identifier = 305
END OF OUTPUT FOR JOB 79
JOB: 80
PC Time&Date: 11:58:39 03/23/2005
NE Time&Date: 13:00:14 09/15/2004
USER NAME: NSN
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: Operation successful
Test Report:
name = BTSETEST:4
testOutcome = PASSED
testTermination = Normal
MOT = RACK:0/DULNA:0
executedPhases =
PreliminaryTestsDulna
CheckAlarmStatusDulna
EndTestDulna
END OF OUTPUT FOR JOB 80
JOB: 81
PC Time&Date: 11:58:39 03/23/2005
NE Time&Date: 13:00:14 09/15/2004
USER NAME: NSN
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: Operation successful
DN0933412 Issue 01321
BTSplus mainline commands at the Flexi BSC product family
DULNA
Id:0900d805805b1089
ChangedConfigurationNotification:
name = BTSETEST:4
ChangeInfo = deleted
END OF OUTPUT FOR JOB 81
The test results will be displayed at the end of the test phases.
Result TEST:
name = TEST:<n>
testOutcome = This field represents the test result; one of the fol-lowing values can be displayed:
Pass all the test phases are successfully performed.
Inconclusive the test is aborted by the system or the test is terminated by the opera-tor.
Fail if at least one of the executed phases fail.
mOts = It is the identifier of the hardware object under test.
testTermination = It specifies how the test is terminated, it can assume the following values:
Normal all the test phases are performed.
Abort the test is aborted by system.
Cancel the test is terminated by operator.
executedPhases
phaseId = It represents the list of the executed test phases (in case of successful test result, all the test phases will be listed).
additionalWords =
....
failedPhases
phaseId = It represents the list of the failed test phase; addi-tional information is provided for each phase.phaseId =
....
skippedPhases
phaseId = It represents the list of the skipped phases; they are displayed only for test stopped during it execution.phaseId =
....
poprosedRepair Action =
A list of most probable fail probable causes is shown (max four messages)
322DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805b1089
DULNA
Operation Failed
This NACK-message occurs in the following cases: Message cannot be performed, test not supported, capacity restrictions, physical configuration cannot be performed, object not locked.
Application Guidelines:
• In phase 3 MO must be locked previous to the command execution
Example of Command Execution:Perftest DULNA:NAME=RACK:0/DULNA:0;
SET DULNA
Command Tree:“MANAGED-ELEMENT h BSS-EQUIPMENT h BTSEP h RACK h DULNA h SET DULNA”
Applicability:Phase 2 and Phase 3.
Visibility level: 2.
Command Description:This command sets the attributes of the DULNA (Low Noise Amplifier of Duplex Antenna Multicoupler) to the BTSE data base.
Long Names:NAME Address of the managed object
LNAMDB lnaModeDb
SCELLNO secondCellNumber
WDLNA wiringDataLna
GNADB gainAdjustDb
System Responses:Operation Completed
After command execution, a message of Changed Attribute Event Report is displayed. A further message indicates the result of the operation. An example of set command is the following:
JOB: 75
PC Time&Date: 11:58:36 03/23/2005
NE Time&Date: 13:00:11 09/15/2004
SET DULNA NAME=RACK:0..7/DULNA:0..11 [,LNAMDB=] [,SCELLNO=] [,WDLNA=] [,GNADB=];
DN0933412 Issue 01323
BTSplus mainline commands at the Flexi BSC product family
DULNA
Id:0900d805805b1089
USER NAME: NSN
COMMAND: Set DULNA:NAME=RACK:0/DULNA:0;
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: Operation successful
END OF OUTPUT FOR JOB 75
Operation Failed
The specified attributes have not been set. In addition to the general NACK causes, a specific NACK cause, which indicates that the command is inconsistent with the physical configuration, is possible.
Application Guidelines:
• One DUAMCO contains two DUAMCO_LNA. The first DUAMCO within the rack is put in the first slot, the second DUAMCO in the second slot and so on. This means that DUAMCO_LNA 0 and DUAMCO_LNA 1 are always physically located in the first slot within the rack, the DUAMCO_LNA 2 and DUAMCO_LNA 3 in the second slot and so on
• The DUAMCO_LNA and the CUs must be in the same rack and must belong to the same cell
• Each CU has a 'normal path' RX input and a 'diversity path' RX input and the operator must indicate which of them is wired to the DUAMCO_LNA
• Wildcard addressing is not possible
• All CUs which are listed in a previous GET DULNA for WDLNA have to be locked (LOCK CU command) before one of these CUs can be removed from WDLNA. Before locking these CUs first a shutdown of the TRXs related to these CUs should be done
Example of Command Execution:Set DULNA:NAME=RACK:0/DULNA:0,SCELLNO=2,WDLNA=CU0N&CU1N&
CU2N&CU3N;
STOPTEST DULNA
Command Tree:“MANAGED-ELEMENT h BSS-EQUIPMENT h BTSEP h RACK h DULNA h STOPTEST DULNA”
Applicability:Phase 2 and Phase 3.
Visibility level: 1.
Command Description:This command is used to stop a diagnostic previously started.
STOPTEST DULNA NAME=RACK:0..7/DULNA:0..11;
324DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805b1089
DULNA
Long Names:NAME Address of the managed object
System Responses:Operation Completed
Test has been stopped. The System Responses will not be addressed to the MOT but to the object BTSEP.
Operation Failed
Test has not been stopped. This NACK-message can occur when the specified test is not running or in case of test which cannot be stopped.
Application Guidelines:None.
Example of Command Execution:Stoptest DULNA:NAME=RACK:0/DULNA:0;
UNLOCK DULNA
Command Tree:“MANAGED-ELEMENT h BSS-EQUIPMENT h BTSEP h RACK h DULNA h UNLOCK DULNA”
Result TEST:
name = TEST:<n>
testOutcome = inconclusive
mOts = It is the identifier of the hardware object under test.
testTermination = Cancel
executedPhases
phaseId = It represents the list of the executed test phases; the list is not shown for test in the waiting list (queued)....
.
failedPhases
phaseId = It represents the list of the failed test phase;
additional information is provided for each phase.phaseId =
....
skippedPhases
phaseId = It represents the list of the skipped phases;the list is not shown for test in the waiting list (queued).phaseId =
UNLOCK DULNA NAME=RACK:0..7/DULNA:0..11;
DN0933412 Issue 01325
BTSplus mainline commands at the Flexi BSC product family
DULNA
Id:0900d805805b1089
Applicability:Phase 2 and Phase 3.
Visibility level: 1.
Command Description:This command changes the administrative state of the DULNA (Duplex Antenna Multi-coupler).
Long Names:NAME Address of the managed object
System Responses:Operation Completed
The specified change of administrative state has been perfomed:
JOB: 82
PC Time&Date: 11:58:41 03/23/2005
NE Time&Date: 13:00:16 09/15/2004
USER NAME: NSN
COMMAND: Unlock DULNA:NAME=RACK:0/DULNA:0;
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: Operation successful
administrativeState = Unlocked
END OF OUTPUT FOR JOB 82
CHANGED STATE EVENT REPORT:
This provides information about the administrative state, the operational state and the availability status every time a state change occurs:
JOB: 83
PC Time&Date: 11:58:41 03/23/2005
NE Time&Date: 13:00:16 09/15/2004
USER NAME: NSN
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: Operation successful
326DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805b1089
DULNA
CHANGED STATE EVENT REPORT:
NAME = RACK:0/DULNA:0
Administrative State = UNLOCKED
Notification Identifier = 306
END OF OUTPUT FOR JOB 83
Operation Failed
The specified change of administrative state has not been performed.
Application Guidelines:None.
Example of Command Execution:Unlock DULNA:NAME=RACK:0/DULNA:0;
DN0933412 Issue 01327
BTSplus mainline commands at the Flexi BSC product family
DUVSWR
Id:0900d805805b108b
DUVSWRThe DUVSWR object represents the VSWR of DUAMCO. A VSWR alarm indicates an antenna failure.
CREATE DUVSWR
Command Tree:“MANAGED-ELEMENT h BSS-EQUIPMENT h BTSEP h RACK h DUVSWR h CREATE DUVSWR”
Applicability:Phase 2 and Phase 3.
Visibility level: 2.
Command Description:This command adds the DUVSWR (Voltage Standing Wave Ratio Duplex Antenna Mul-ticoupler) together with its attributes to the BTSE data base.
Long Names:NAME Address of the managed object
CELLNO cellNumber
COMBMD combMode
WDDUVSWR wiringDuamcoVswr
VSWRTDB vswrThresholdDb
System Responses:Operation Completed
After command execution, a message of Changed Configuration Notification is dis-played. A further message indicates the result of the operation. An example of create command is the following:
JOB: 112
PC Time&Date: 12:00:05 03/23/2005
NE Time&Date: 13:01:40 09/15/2004
USER NAME: NSN_Robert
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: Operation successful
ChangedConfigurationNotification:
CREATE DUVSWR NAME=RACK:0..7/DUVSWR:0..11 ,CELLNO= ,COMBMD= ,WDDUVSWR= [,VSWRTDB=];
328DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805b108b
DUVSWR
name = RACK:0/DUVSWR:0
ChangeInfo = created
END OF OUTPUT FOR JOB 112
JOB: 113
PC Time&Date: 12:00:05 03/23/2005
NE Time&Date: 13:01:40 09/15/2004
USER NAME: NSN_Robert
COMMAND: Create DUVSWR:NAME=RACK:0/DUVSWR:0,CELLNO=0,WDDU-VSWR=CU0,COMBMD=OneToOne;
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: Operation successful
cellNumber = 0
wiringDuamcoVswr = CU0
combMode = OneToOne
END OF OUTPUT FOR JOB 113
Operation Failed
The specified Object has not been created. In addition to the general NACK causes, a specific NACK cause, which indicates that the command is inconsistent with the physical configuration, is possible. An example is the following:
JOB: 114
PC Time&Date: 12:00:05 03/23/2005
NE Time&Date: 13:01:40 09/15/2004
USER NAME: NSN_Robert
COMMAND: Create DUVSWR:NAME=RACK:0/DUVSWR:2;
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: OPERATION FAILED
Object instance unknown (-9)
END OF OUTPUT FOR JOB 114
DN0933412 Issue 01329
BTSplus mainline commands at the Flexi BSC product family
DUVSWR
Id:0900d805805b108b
Application Guidelines:
• One DUAMCO contains two DUAMCO_VSWR. The first DUAMCO within the rack is put in the first slot, the second DUAMCO in the second slot and so on. This means that DUAMCO_VSWR 0 and DUAMCO_VSWR 1 are always physically located in the first slot within the rack, the DUAMCO_VSWR 2 and DUAMCO_VSWR 3 in the second slot and so on
• The DUAMCO_VSWR and the CUs must be in the same rack and must belong to the same cell
• Due to the physical properties of the DUAMCO_VSWR, up to 4 CUs can be con-nected
• Wildcard addressing is not possible
Example of Command Execution:Create DUVSWR:NAME=RACK:0/DUVSWR:0,CELLNO=0,COMBMD=TwoToTwo,
WDDUVSWR=CU0&CU1;
DELETE DUVSWR
Command Tree:“MANAGED-ELEMENT h BSS-EQUIPMENT h BTSEP h RACK h DUVSWR h DELETE DUVSWR”
Applicability:Phase 2 and Phase 3.
Visibility level: 2.
Command Description:This command deletes the DUVSWR (Voltage Standing Wave Ratio Duplex Antenna Multicoupler) together with its attributes from the BTSE data base.
Long Names:NAME Address of the managed object
System Responses:Operation Completed
After command execution, a message of Changed Configuration Notification is dis-played. A further message indicates the result of the operation. An example of delete command is the following:
JOB: 110
PC Time&Date: 11:59:58 03/23/2005
NE Time&Date: 13:01:33 09/15/2004
DELETE DUVSWR NAME=RACK:0..7/DUVSWR:0..11;
330DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805b108b
DUVSWR
USER NAME: NSN_Robert
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: Operation successful
ChangedConfigurationNotification:
name = RACK:0/DUVSWR:0
ChangeInfo = deleted
END OF OUTPUT FOR JOB 110
JOB: 111
PC Time&Date: 11:59:58 03/23/2005
NE Time&Date: 13:01:33 09/15/2004
USER NAME: NSN_Robert
COMMAND: Delete DUVSWR:NAME=RACK:0/DUVSWR:0;
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: Operation successful
END OF OUTPUT FOR JOB 111
Operation Failed
The specified Object has not been deleted. Additionally to the general NACK causes, a specific NACK cause, meaning that the command is inconsistent with physical configu-ration, is possible.
Application Guidelines:
• DUVSWR must be locked in Phase 3, before deletion
• If this object is deleted, the related TRXs are out of service
Example of Command Execution:Delete DUVSWR:NAME=RACK:0/DUVSWR:0;
GET DUVSWRGET DUVSWR NAME=RACK:0..7/DUVSWR:0..11 [,REQATTL=ALS, AST,
AVS, CELLNO, COMBMD, OST, PRS, RELFUNCOBJ, WDDUVSWR, VSWRTDB];
DN0933412 Issue 01331
BTSplus mainline commands at the Flexi BSC product family
DUVSWR
Id:0900d805805b108b
Command Tree:“MANAGED-ELEMENT h BSS-EQUIPMENT h BTSEP h RACK h DUVSWR h GET DUVSWR”
Applicability:Phase 2 and Phase 3.
Visibility level: 0.
Command Description:This command displays the attributes of the DUVSWR (Voltage Standing Wave Ratio Duplex Antenna Multicoupler).
Long Names:NAME Address of the managed object
REQATTL Required attribute list
ALS alarmStatus
AST administrativeState
AVS availabilityStatus
CELLNO cellNumber
COMBMD combMode
OST operationalState
PRS proceduralStatus
RELFUNCOBJ relatedFuncObjects
WDDUVSWR wiringDuamcoVswr
VSWRTDB vswrThresholdDb
System Responses:Operation Completed
After command execution, a message of Changed Configuration Notification is dis-played. A further message indicates the result of the operation. An example of get command is the following:
JOB: 95
PC Time&Date: 11:59:35 03/23/2005
NE Time&Date: 13:01:10 09/15/2004
USER NAME: NSN_Robert
COMMAND: Get DUVSWR:NAME=RACK:0/DUVSWR:0;
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: Operation successful
alarmStatus = CLEARED
332DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805b108b
DUVSWR
administrativeState = Locked
availabilityStatus = NULL
cellNumber = 0
combMode = TwoToTwo
operationalState = ENABLED
proceduralStatus = NULL
relatedFuncObjects = BTS:0/TRX:2
wiringDuamcoVswr = CU0
END OF OUTPUT FOR JOB 95
Operation Failed
The GET command has not been successfully executed. A general NACK will indicate possible errors or a specific NACK strictly related to the single command is possible.
Application Guidelines:
• The value for the attribute gsmFunctionalID in LMT Evolution Phase 2 is "not con-figured"
• The value for proceduralStatus must be NULL
Example of Command Execution:Get DUVSWR:NAME=RACK:0/DUVSWR:0,REQATTL=ALS&AST&AVS&CELLNO&
COMBMD&OST&PRS&RELFUNCOBJ&DDUVSWR;
GETTEST DUVSWR
Command Tree:“MANAGED-ELEMENT h BSS-EQUIPMENT h BTSEP h RACK h DUVSWR h GETTEST DUVSWR”
Applicability:Phase 2 and Phase 3.
Visibility level: 0.
Command Description:This command displays the attributes of the object test.
Long Names:NAME Address of the managed object
REQATTL Required attribute list
System Responses:Operation Completed
GETTEST DUVSWR NAME=RACK:0..7/DUVSWR:0..11;
DN0933412 Issue 01333
BTSplus mainline commands at the Flexi BSC product family
DUVSWR
Id:0900d805805b108b
After command execution, a message of Changed Configuration Notification is dis-played. A further message indicates the result of the operation. An example of gettest command is the following:
JOB: 101
PC Time&Date: 11:59:50 03/23/2005
NE Time&Date: 13:01:25 09/15/2004
USER NAME: NSN_Robert
COMMAND: Gettest DUVSWR:NAME=RACK:0/DUVSWR:0;
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: Operation successful
MOT = RACK:0/DUVSWR:0
testMonitor =
phaseId = PreliminaryTestsDuvswr
phaseStatus = Running
phaseId = CheckAlarmStatusDuvswr
phaseStatus = Waiting
phaseId = EndTestDuvswr
phaseStatus = Waiting
testOutcome = INCONCLUSIVE
testState = INITIALIZING
END OF OUTPUT FOR JOB 101
Operation Failed
The GET command has not been successfully executed. A general NACK will indicate possible errors or a specific NACK strictly related to the single command is possible.
testMonitor it is a list of all test phases related to the selected object; for each phase the related phaseStatus is provided (Passed, Failed, Running or Waiting).
phaseId =
phaseStatus =
phaseId =
phaseStatus =
...
...
334DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805b108b
DUVSWR
Application Guidelines:None.
Example of Command Execution:Gettest DUVSWR:NAME=RACK:0/DUVSWR:0;
LOCK DUVSWR
Command Tree:“MANAGED-ELEMENT h BSS-EQUIPMENT h BTSEP h RACK h DUVSWR h LOCK DUVSWR”
Applicability:Phase 2 and Phase 3.
Visibility level: 1.
Command Description:This command changes the administrative state of DUVSWR (Voltage Standing Wave Ratio Duplex Antenna Multicoupler).
Long Names:NAME Address of the managed object
System Responses:Operation Completed
The specified change of administrative state has been perfomed:
JOB: 99
PC Time&Date: 11:59:48 03/23/2005
NE Time&Date: 13:01:23 09/15/2004
USER NAME: NSN_Robert
COMMAND: Lock DUVSWR:NAME=RACK:0/DUVSWR:0;
SW RELEASE: 01-04-17-01-26-51_05-02-23
testOutcome It represents the test result: it can be Inconclusive (if the phases already executed were successful) or Fail (if at least one of the executed phases failed).
testState = Testing It can assume one of the following values: not_initialized, idle, initializing, sus-pended, testing, terminating and dis-abled.
LOCK DUVSWR NAME=RACK:0..7/DUVSWR:0..11;
DN0933412 Issue 01335
BTSplus mainline commands at the Flexi BSC product family
DUVSWR
Id:0900d805805b108b
COMMAND RESULT: Operation successful
administrativeState = Locked
END OF OUTPUT FOR JOB 99
CHANGED STATE EVENT REPORT:
This provides information about the administrative state, the operational state and the availability status every time a state change occurs:
JOB: 100
PC Time&Date: 11:59:48 03/23/2005
NE Time&Date: 13:01:23 09/15/2004
USER NAME: NSN_Robert
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: Operation successful
CHANGED STATE EVENT REPORT:
NAME = RACK:0/DUVSWR:0
Administrative State = LOCKED
Notification Identifier = 312
END OF OUTPUT FOR JOB 100
Operation Failed
The specified change of administrative state has not been performed.
Application Guidelines:None.
Example of Command Execution:Lock DUVSWR:NAME=RACK:0/DUVSWR:0;
PERFTEST DUVSWR
Command Tree:“MANAGED-ELEMENT h BSS-EQUIPMENT h BTSEP h RACK h DUVSWR h PERFTEST DUVSWR”
PERFTEST DUVSWR NAME=RACK:0..7/DUVSWR:0..11;
336DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805b108b
DUVSWR
Applicability:Phase 2 and Phase 3.
Visibility level: 1.
Command Description:This command is used to start an asynchronous test in the object.
Long Names:NAME Address of the managed object
System Responses:Operation Completed
Test configuration has been set and the specified test has been started. The System response will not be addressed to the MOT but to the object BTSEP.
JOB: 102
PC Time&Date: 11:59:50 03/23/2005
NE Time&Date: 13:01:25 09/15/2004
USER NAME: NSN_Robert
COMMAND: Perftest DUVSWR:NAME=RACK:0/DUVSWR:0;
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: Operation successful
MOT = RACK:0/DUVSWR:0
tO = BTSETEST:5
END OF OUTPUT FOR JOB 102
JOB: 103
PC Time&Date: 11:59:50 03/23/2005
NE Time&Date: 13:01:25 09/15/2004
USER NAME: NSN_Robert
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: Operation successful
ChangedConfigurationNotification:
DN0933412 Issue 01337
BTSplus mainline commands at the Flexi BSC product family
DUVSWR
Id:0900d805805b108b
name = BTSETEST:5
ChangeInfo = created
END OF OUTPUT FOR JOB 103
JOB: 104
PC Time&Date: 11:59:50 03/23/2005
NE Time&Date: 13:01:25 09/15/2004
USER NAME: NSN_Robert
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: Operation successful
CHANGED STATE EVENT REPORT:
NAME = RACK:0/DUVSWR:0
Operational State = ENABLED
Availability Status = NULL_value
Notification Identifier = 316
END OF OUTPUT FOR JOB 104
JOB: 105
PC Time&Date: 11:59:50 03/23/2005
NE Time&Date: 13:01:25 09/15/2004
USER NAME: NSN_Robert
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: Operation successful
Test Report:
name = BTSETEST:5
testOutcome = PASSED
testTermination = Normal
MOT = RACK:0/DUVSWR:0
executedPhases =
338DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805b108b
DUVSWR
PreliminaryTestsDuvswr
CheckAlarmStatusDuvswr
EndTestDuvswr
END OF OUTPUT FOR JOB 105
JOB: 106
PC Time&Date: 11:59:50 03/23/2005
NE Time&Date: 13:01:25 09/15/2004
USER NAME: NSN_Robert
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: Operation successful
ChangedConfigurationNotification:
name = BTSETEST:5
ChangeInfo = deleted
END OF OUTPUT FOR JOB 106
The test results will be displayed at the end of the test phases.
Result TEST:
name = TEST:<n>
testOutcome = This field represents the test result; one of the fol-lowing values can be displayed:
Pass all the test phases are successfully performed.
Inconclusive the test is aborted by the system or the test is terminated by the opera-tor.
Fail if at least one of the executed phases fail.
mOts = It is the identifier of the hardware object under test.
testTermination = It specifies how the test is terminated, it can assume the following values:
Normal all the test phases are performed.
Abort the test is aborted by system.
Cancel the test is terminated by operator.
DN0933412 Issue 01339
BTSplus mainline commands at the Flexi BSC product family
DUVSWR
Id:0900d805805b108b
Operation Failed
This NACK-message occurs in the following cases: Message cannot be performed, test not supported, capacity restrictions, physical configuration cannot be performed, object not locked.
Application Guidelines:
• In phase 3 MO must be locked previous to the command execution
Example of Command Execution:Perftest DUVSWR:NAME=RACK:0/DUVSWR:0;
SET DUVSWR
Command Tree:“MANAGED-ELEMENT h BSS-EQUIPMENT h BTSEP h RACK h DUVSWR h SET DUVSWR”
Applicability:Phase 2 and Phase 3.
Visibility level: 2.
Command Description:This command sets the attributes of the DUVSWR (Voltage Standing Wave Ratio Duplex Antenna Multicoupler) to the BTSE data base.
Long Names:NAME Address of the managed object
executedPhases
phaseId = It represents the list of the executed test phases (in case of successful test result, all the test phases will be listed).
additionalWords =
....
failedPhases
phaseId = It represents the list of the failed test phase; addi-tional information is provided for each phase.phaseId =
....
skippedPhases
phaseId = It represents the list of the skipped phases; they are displayed only for test stopped during it execution.phaseId =
....
poprosedRepair Action =
A list of most probable fail probable causes is shown (max four messages)
SET DUVSWR NAME=RACK:0..7/DUVSWR:0..11 [,WDDUVSWR=] [,VSWRTDB=];
340DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805b108b
DUVSWR
WDDUVSWR wiringDuamcoVswr
VSWRTDB vswrThresholdDb
System Responses:Operation Completed
After command execution, a message of Changed Attribute Event Report is displayed. A further message indicates the result of the operation. An example of set command is the following:
JOB: 109
PC Time&Date: 11:59:53 03/23/2005
NE Time&Date: 13:01:28 09/15/2004
USER NAME: NSN_Robert
COMMAND: Set DUVSWR:NAME=RACK:0/DUVSWR:0;
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: Operation successful
END OF OUTPUT FOR JOB 109
Operation Failed
The specified attributes have not been set. In addition to the general NACK causes, a specific NACK cause, which indicates that the command is inconsistent with the physical configuration, is possible.
Application Guidelines:
• One DUAMCO contains two DUAMCO_VSWR. The first DUAMCO within the rack is put in the first slot, the second DUAMCO in the second slot and so on. This means that DUAMCO_VSWR 0 and DUAMCO_VSWR 1 are always physically located in the first slot within the rack, the DUAMCO_VSWR 2 and DUAMCO_VSWR 3 in the second slot and so on
• The DUAMCO_VSWR and the CUs must be in the same rack and must belong to the same cell
• Due to the physical properties of the DUAMCO_VSWR, up to 4 CUs can be con-nected
• Wildcard addressing is not possible
• All CUs which are listed in a previous GET DUVSWR for WDDUVSWR have to be locked (LOCK CU command) before one of these CUs can be removed from WDDUVSWR. Before locking these CUs first a shutdown of the TRXs related to these CUs should be done
Example of Command Execution:Set DUVSWR:NAME=RACK:0/DUVSWR:0,WDLNA=CU0N&CU1N&CU2N&CU3N;
DN0933412 Issue 01341
BTSplus mainline commands at the Flexi BSC product family
DUVSWR
Id:0900d805805b108b
STOPTEST DUVSWR
Command Tree:“MANAGED-ELEMENT h BSS-EQUIPMENT h BTSEP h RACK h DUVSWR h STOPTEST DUVSWR”
Applicability:Phase 2 and Phase 3.
Visibility level: 1.
Command Description:This command is used to stop a diagnostic previously started.
Long Names:NAME Address of the managed object
System Responses:Operation Completed
Test has been stopped. The System Responses will not be addressed to the MOT but to the object BTSEP.
Operation Failed
Test has not been stopped. This NACK-message can occur when the specified test is not running or in case of test which cannot be stopped.
STOPTEST DUVSWR NAME=RACK:0..7/DUVSWR:0..11;
Result TEST:
name = TEST:<n>
testOutcome = inconclusive
mOts = It is the identifier of the hardware object under test.
testTermination = Cancel
executedPhases
phaseId = It represents the list of the executed test phases; the list is not shown for test in the waiting list (queued)....
.
failedPhases
phaseId = It represents the list of the failed test phase;
additional information is provided for each phase.phaseId =
....
skippedPhases
phaseId = It represents the list of the skipped phases;the list is not shown for test in the waiting list (queued).phaseId =
342DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805b108b
DUVSWR
Application Guidelines:None.
Example of Command Execution:Stoptest DUVSWR:NAME=RACK:0/DUVSWR:0;
UNLOCK DUVSWR
Command Tree:“MANAGED-ELEMENT h BSS-EQUIPMENT h BTSEP h RACK h DUVSWR h UNLOCK DUVSWR”
Applicability:Phase 2 and Phase 3.
Visibility level: 1.
Command Description:This command changes the administrative state of the DUVSWR (Voltage Standing Wave Ratio Duplex Antenna Multicoupler).
Long Names:NAME Address of the managed object
System Responses:Operation Completed
The specified change of administrative state has been perfomed:
JOB: 97
PC Time&Date: 11:59:44 03/23/2005
NE Time&Date: 13:01:19 09/15/2004
USER NAME: NSN_Robert
COMMAND: Unlock DUVSWR:NAME=RACK:0/DUVSWR:0;
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: Operation successful
administrativeState = Unlocked
END OF OUTPUT FOR JOB 97
CHANGED STATE EVENT REPORT:
UNLOCK DUVSWR NAME=RACK:0..7/DUVSWR:0..11;
DN0933412 Issue 01343
BTSplus mainline commands at the Flexi BSC product family
DUVSWR
Id:0900d805805b108b
This provides information about the administrative state, the operational state and the availability status every time a state change occurs:
JOB: 98
PC Time&Date: 11:59:44 03/23/2005
NE Time&Date: 13:01:19 09/15/2004
USER NAME: NSN_Robert
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: Operation successful
CHANGED STATE EVENT REPORT:
NAME = RACK:0/DUVSWR:0
Administrative State = UNLOCKED
Notification Identifier = 311
END OF OUTPUT FOR JOB 98
Operation Failed
The specified change of administrative state has not been performed.
Application Guidelines:None.
Example of Command Execution:Unlock DUVSWR:NAME=RACK:0/DUVSWR:0;
344DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805b108d
ENVABTSE
ENVABTSEThe ENVABTSE object is used to manage the enviromental alarms of the BTSplus mainline.
CREATE ENVABTSE
Command Tree:“MANAGED-ELEMENT h BSS-EQUIPMENT h BTSEP h RACK h ENVABTSE h CREATE ENVABTSE”
Applicability:Phase 2 and Phase 3.
Visibility level: 2.
Command Description:This command configures one of the 9 possible environmental alarms (in the Base Rack optionally the ACTM can be installed that supplies 48 additional ENVAs) in the BTSE database (BS40/41, BS240/241, BS240XL, BS40II).
For BS82II this command configures one of the 6 possible environmental alarms.
Long Names:NAME Address of the managed object
ASEV associatedSeverity
ASTRING associatedString
INTINF interfaceInformation
System Responses:Operation Completed
After command execution, a message of Changed Configuration Notification is dis-played. A further message indicates the result of the operation. An example of create command is the following:
JOB: 116
PC Time&Date: 12:00:26 03/23/2005
NE Time&Date: 13:02:01 09/15/2004
USER NAME: NSN
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: Operation successful
CREATE ENVABTSE NAME=RACK:0..7/ENVABTSE:0..56 [,ASEV=] [,ASTRING=] ,INTINF=;
DN0933412 Issue 01345
BTSplus mainline commands at the Flexi BSC product family
ENVABTSE
Id:0900d805805b108d
ChangedConfigurationNotification:
name = RACK:0/ENVABTSE:0
ChangeInfo = created
END OF OUTPUT FOR JOB 116
JOB: 117
PC Time&Date: 12:00:26 03/23/2005
NE Time&Date: 13:02:01 09/15/2004
USER NAME: NSN
COMMAND: Create ENVABTSE:NAME=RACK:0/ENVABTSE:0,INTINF=low;
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: Operation successful
interfaceInformation = low
END OF OUTPUT FOR JOB 117
Operation Failed
The specified Object has not been created. In addition to the general NACK causes, a specific NACK cause, which indicates that the command is inconsistent with the physical configuration, is possible. An example is the following:
JOB: 119
PC Time&Date: 12:00:31 03/23/2005
NE Time&Date: 13:02:06 09/15/2004
USER NAME: NSN
COMMAND: Create ENVABTSE:NAME=RACK:0/ENVABTSE:1,INTINF=high;
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: OPERATION FAILED
Message cannot be performed (-17)
END OF OUTPUT FOR JOB 119
346DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805b108d
ENVABTSE
Application Guidelines:For BS241:
• All ENVAs can be left as not equipped
• In the Base Rack with only ACTC installed 9 ENVAs within the range from 0...8 are supported as shown in the table below. In the Base Rack optionally the ACTM can be installed that supplies 48 additional ENVAs
• In the other Racks with ACTC installed 9 ENVAs within the range from 0...8 are sup-ported as shown in the table below
For BS240 Compact Site:
• The AC/DC alarm line for the AC/DC converter and for the battery must be con-nected to a site input which is used as a trigger for the emergency configuration
• A special setting of the attribute "associatedString" in the corresponding site input allows the operator to indicate that the support of emergency configuration is required for the 3rd party battery backup unit system. The string indicates from which source, AC/DC CAN node or site input, the trigger for the emergency config-uration is expected. In case the string pattern is set to "##ACDC_FAULT" the trigger is expected from the site input of the corresponding ENVABTSE object. In all other cases the normal behavior is maintained
• For simplicity there is no check if the string "##ACDC_FAULT" is used for more than one ENVABTSE object. If the operator has set the "associatedString" attribute of an ENVABTSE object to "##ACDC_FAULT" for the AC/DC alarm line, the emergency configuration is deactivated if all trigger sources have ceased their alarm
ENVA No. Application
0 Heatexchanger - 0
1 Heatexchanger - 1
2 Heatexchanger - 2
3 Rack/Shelter in service
4 Smoke
5 Battery Fuse 0, 1, 2
6 Over Voltage Protection (it has to be configured with "HIGH")
7
8 Microwave
ENVA No. Applica-tion
Severity String
6 HIGH CRITICAL Over Voltage Protection (¿¿¿)
9 HIGH CRITICAL Shelter door open
10 HIGH CRITICAL Conditioners FAULT
DN0933412 Issue 01347
BTSplus mainline commands at the Flexi BSC product family
ENVABTSE
Id:0900d805805b108d
For BS40II:
– The FAN5 alarm is not utilized in the case of a BS-40II (deactivated by S/W).
– ACTC-3 alarms
11 HIGH CRITICAL Shelter Temperature Out Tolerance
12 HIGH CRITICAL Shelter in service
13 HIGH CRITICAL Not connected
14 HIGH CRITICAL Mains Breakdown
15 HIGH CRITICAL Critical Battery Breakdown
16 HIGH CRITICAL Critical Battery Charging Fault
17 HIGH CRITICAL -48 dc Out Tolerance
18 HIGH CRITICAL Redundancy Lost
19 HIGH CRITICAL Not connected
20 HIGH CRITICAL Not connected
21 HIGH CRITICAL Not connected
22 HIGH CRITICAL Not connected
27 HIGH CRITICAL Critical Smoke
28 HIGH CRITICAL Critical Available 1
29 HIGH CRITICAL Critical Available 2
30 HIGH CRITICAL Critical AC lightning Protection
31 HIGH CRITICAL Critical Available 3
32 HIGH CRITICAL Critical Available 4
33 HIGH CRITICAL Critical Available 5
34 HIGH CRITICAL Critical Conditioner ALM
34 HIGH CRITICAL Critical Filters ALM
36 HIGH CRITICAL Critical Available 6
37 HIGH CRITICAL Critical Available 7
38 HIGH CRITICAL Critical Available 8
39 HIGH CRITICAL Critical Available 9
40 HIGH CRITICAL Critical Available 10
ENVA No.
0 High / Low Active
1 High / Low Active
2 High / Low Active Mains Breackdown (MBR) note 1 and 2
3 High / Low Active Battery Breackdown (BBR) note 1
348DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805b108d
ENVABTSE
Note:
1. Only relevant for BS with AC/DC system, all AC/DC alarms are "High Active".
2. For MBR alarm the 'associated string' must be: '##ACDC_FAULT' to make this alarm trigger the 'emergency configuration'.'emergency configuration'
Example of Command Execution:Create ENVABTSE:NAME=RACK:0/ENVABTSE:17,INTINF=high,
ASEV=CRITICAL, ASTRING="Air Condition. Sys. Fault";
DELETE ENVABTSE
Command Tree:“MANAGED-ELEMENT h BSS-EQUIPMENT h BTSEP h RACK h ENVABTSE h DELETE ENVABTSE”
Applicability:Phase 2 and Phase 3.
Visibility level: 2.
Command Description:BS24x, BS4x
This command deletes one of the 9 possible environmental alarms (in the Base Rack optionally the ACTM can be installed that supplies 48 additional ENVAs) from the BTSE database.
Long Names:NAME Address of the managed object
System Responses:Operation Completed
After command execution, a message of Changed Configuration Notification is dis-played. A further message indicates the result of the operation. An example of delete command is the following:
JOB: 130
PC Time&Date: 12:00:52 03/23/2005
4 SMOKE - High / Low Active
5 Battery Breacker (BB) - High / Low Active
6 Over Voltage Protection(OVP) - High / Low Active
7 High / Low Active - Battery Charger Fault (BCHF) note 1
8 High / Low Active - -48Vdc Out of Tolerance (48OTB) note 1
DELETE ENVABTSE NAME=RACK:0..7/ENVABTSE:0..56;
DN0933412 Issue 01349
BTSplus mainline commands at the Flexi BSC product family
ENVABTSE
Id:0900d805805b108d
NE Time&Date: 13:02:27 09/15/2004
USER NAME: NSN
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: Operation successful
ChangedConfigurationNotification:
name = RACK:0/ENVABTSE:0
ChangeInfo = deleted
END OF OUTPUT FOR JOB 130
JOB: 131
PC Time&Date: 12:00:52 03/23/2005
NE Time&Date: 13:02:27 09/15/2004
USER NAME: NSN
COMMAND: Delete ENVABTSE:NAME=RACK:0/ENVABTSE:0;
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: Operation successful
END OF OUTPUT FOR JOB 131
Operation Failed
The specified Object has not been deleted. Additionally to the general NACK causes, a specific NACK cause, meaning that the command is inconsistent with physical configu-ration, is possible.
Application Guidelines:
• ENVABTSE must be locked in phase 3 before deletion
Example of Command Execution:Delete ENVABTSE:NAME=RACK:0/ENVABTSE:17;
GET ENVABTSEGET ENVABTSE NAME=RACK:0..7/ENVABTSE:0..56 [,REQATTL=ALS,
ASEV, AST, ASTRING, AVS, INTINF, OST, PRS, RELFUN-COBJ];
350DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805b108d
ENVABTSE
Command Tree:“MANAGED-ELEMENT h BSS-EQUIPMENT h BTSEP h RACK h ENVABTSE h GET ENVABTSE”
Applicability:Phase 2 and Phase 3.
Visibility level: 0.
Command Description:This command displays the attributes of the specified Environmental Alarm stored in the BTSE database.
Long Names:NAME Address of the managed object
REQATTL Required attribute list
ALS alarmStatus
ASEV associatedSeverity
AST administrativeState
ASTRING associatedString
AVS availabilityStatus
INTINF interfaceInformation
OST operationalState
PRS proceduralStatus
RELFUNCOBJ relatedFuncObjects
System Responses:Operation Completed
After command execution, a message of Changed Configuration Notification is dis-played. A further message indicates the result of the operation. An example of get command is the following:
JOB: 118
PC Time&Date: 12:00:29 03/23/2005
NE Time&Date: 13:02:04 09/15/2004
USER NAME: NSN
COMMAND: Get ENVABTSE:NAME=RACK:0/ENVABTSE:0;
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: Operation successful
alarmStatus = CLEARED
associatedSeverity = DEFAULT_DB
DN0933412 Issue 01351
BTSplus mainline commands at the Flexi BSC product family
ENVABTSE
Id:0900d805805b108d
administrativeState = Unlocked
associatedString =
availabilityStatus = NULL
interfaceInformation = low
operationalState = ENABLED
proceduralStatus = NULL
relatedFuncObjects =
END OF OUTPUT FOR JOB 118
Operation Failed
The GET command has not been successfully executed. A general NACK will indicate possible errors or a specific NACK strictly related to the single command is possible.
Application Guidelines:
• For BS24x all environmental alarms can be left as not equipped (default value)
• Refer to Application Guidelines: in CREATE ENVABTSE command for more detailed information.
Example of Command Execution:Get ENVABTSE:NAME=RACK:0/ENVABTSE:17,REQATTL=ALS&ASEV&
ASTRING&AST&AVS&INTINF&OST&PRS&RELFUNCOBJ;
LOCK ENVABTSE
Command Tree:“MANAGED-ELEMENT h BSS-EQUIPMENT h BTSEP h RACK h ENVABTSE h LOCK ENVABTSE”
Applicability:Phase 2 and Phase 3.
Visibility level: 1.
Command Description:This command changes the administrative state of the environmental alarms.
Long Names:NAME Address of the managed object
System Responses:Operation Completed
The specified change of administrative state has been perfomed:
JOB: 128
LOCK ENVABTSE NAME=RACK:0..7/ENVABTSE:0..56;
352DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805b108d
ENVABTSE
PC Time&Date: 12:00:47 03/23/2005
NE Time&Date: 13:02:22 09/15/2004
USER NAME: NSN
COMMAND: Lock ENVABTSE:NAME=RACK:0/ENVABTSE:0;
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: Operation successful
administrativeState = Locked
END OF OUTPUT FOR JOB 1286
CHANGED STATE EVENT REPORT:
This provides information about the administrative state, the operational state and the availability status every time a state change occurs:
JOB: 129
PC Time&Date: 12:00:47 03/23/2005
NE Time&Date: 13:02:22 09/15/2004
USER NAME: NSN
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: Operation successful
CHANGED STATE EVENT REPORT:
NAME = RACK:0/ENVABTSE:0
Administrative State = LOCKED
Notification Identifier = 332
END OF OUTPUT FOR JOB 129
Operation Failed
The specified change of administrative state has not been performed.
Application Guidelines:
• If the administrative state is set to locked, no alarm is generated
DN0933412 Issue 01353
BTSplus mainline commands at the Flexi BSC product family
ENVABTSE
Id:0900d805805b108d
Example of Command Execution:Lock ENVABTSE:NAME=RACK:0/ENVABTSE:0;
SET ENVABTSE
Command Tree:“MANAGED-ELEMENT h BSS-EQUIPMENT h BTSEP h RACK h ENVABTSE h SET ENVABTSE”
Applicability:Phase 2 and Phase 3.
Visibility level: 2.
Command Description:This command configures one of the 9 possible environmental alarms (in the Base Rack optionally the ACTM can be installed that supplies 48 additional ENVAs) in the BTSE database.
Long Names:NAME Address of the managed object
INTINF interfaceInformation
System Responses:Operation Completed
After command execution, a message of Changed Attribute Event Report is displayed. A further message indicates the result of the operation. An example of set command is the following:
JOB: 125
PC Time&Date: 12:00:39 03/23/2005
NE Time&Date: 13:02:14 09/15/2004
USER NAME: NSN
COMMAND: Set ENVABTSE:NAME=RACK:0/ENVABTSE:0;
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: Operation successful
END OF OUTPUT FOR JOB 125
Operation Failed
The specified attributes have not been set. In addition to the general NACK causes, a specific NACK cause, which indicates that the command is inconsistent with the physical configuration, is possible.
SET ENVABTSE NAME=RACK:0..7/ENVABTSE:0..56 [,INTINF=];
354DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805b108d
ENVABTSE
Application Guidelines:
• For BS24x all environmental alarms can be left as not equipped (default value)
• See Application Guidelines: in CREATE ENVABTSE command for more detailed information
• For BS41 and BS241 the smoke alarm must be set on low-active or high-active depending on the respective installed sensor type
Example of Command Execution:Set ENVABTSE:NAME=RACK:0/ENVABTSE:4,INTINF=high;
UNLOCK ENVABTSE
Command Tree:“MANAGED-ELEMENT h BSS-EQUIPMENT h BTSEP h RACK h ENVABTSE h UNLOCK ENVABTSE”
Applicability:Phase 2 and Phase 3.
Visibility level: 1.
Command Description:This command changes the administrative state of the environmental alarms.
Long Names:NAME Address of the managed object
System Responses:Operation Completed
The specified change of administrative state has been perfomed:
JOB: 126
PC Time&Date: 12:00:41 03/23/2005
NE Time&Date: 13:02:16 09/15/2004
USER NAME: NSN
COMMAND: Unlock ENVABTSE:NAME=RACK:0/ENVABTSE:0;
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: Operation successful
administrativeState = Unlocked
END OF OUTPUT FOR JOB 126
UNLOCK ENVABTSE NAME=RACK:0..7/ENVABTSE:0..56;
DN0933412 Issue 01355
BTSplus mainline commands at the Flexi BSC product family
ENVABTSE
Id:0900d805805b108d
CHANGED STATE EVENT REPORT:
This provides information about the administrative state, the operational state and the availability status every time a state change occurs:
JOB: 127
PC Time&Date: 12:00:41 03/23/2005
NE Time&Date: 13:02:16 09/15/2004
USER NAME: NSN
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: Operation successful
CHANGED STATE EVENT REPORT:
NAME = RACK:0/ENVABTSE:0
Administrative State = UNLOCKED
Notification Identifier = 330
END OF OUTPUT FOR JOB 127
Operation Failed
The specified change of administrative state has not been performed.
Application Guidelines:None.
Example of Command Execution:Unlock ENVABTSE:NAME=RACK:0/ENVABTSE:0;
356DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805b1091
ETHCON
ETHCONThe ETHCON board provides external electrical and optical Ethernet interfaces to connect the related Flexi BSC product family, other BTSplus mainlines in multidrop-like configurations and test equipment for Abis monitoring.
It therefore houses a manageable Ethernet switch which is controlled by the COBA. Nevertheless the board is able to operate autonomously from the COBA in order to maintain multidrop-like connections to other BTSE e.g. in case of a COBA reset.
The ETHCON board (ETHernet CONnection) is modeled by:
• one ETHCON instance representing the board
• n ETHPORT instances representing the external Ethernet ports (except for monitor-ing port(s))
The ETHCON object is introduced for state indication and alarm reporting. The object state comprise the board, the traffic link and the switch management link to the COBA.
CREATE ETHCON
Command Tree:“MANAGED-ELEMENT h BSS-EQUIPMENT h BTSEP h RACK h ETHCON h CREATE ETHCON”
Applicability:Phase 2.
Visibility level: 2.
Command Description:This command adds an Ethernet Connection board to the BTSE data base.
Long Names:NAME Address of the managed object
System Responses:Operation Completed
After command execution, a message of Changed Configuration Notification is dis-played. A further message indicates the result of the operation. An example of create command is the following:
JOB: 15
PC Time&Date: 09.10.2008 09:40:08 +02:00
NE Time&Date: 01.01.1990 00:02:17 +00:00
USER NAME: NSN_Paul
COMMAND: Create ETHCON:NAME=RACK:0/ETHCON:0;
SW RELEASE: 03-04-19-06-11-06_08-10-08
COMMAND RESULT:Operation successful
END OF OUTPUT FOR JOB 15
CREATE ETHCON NAME=RACK:0..7/ETHCON:0..0;
DN0933412 Issue 01357
BTSplus mainline commands at the Flexi BSC product family
ETHCON
Id:0900d805805b1091
JOB: 18
PC Time&Date: 09.10.2008 09:40:08 +02:00
NE Time&Date: 01.01.1990 00:02:17 +00:00
USER NAME: NSN_Paul
SW RELEASE: 03-04-19-06-11-06_08-10-08
COMMAND RESULT: Operation successful
CHANGED STATE EVENT REPORT:
NAME = RACK:0/ETHCON:0
Operational State = ENABLED
Availability Status = NULL_VALUE
Notification Identifier = 38
END OF OUTPUT FOR JOB 18
Operation Failed
None.
Application Guidelines:
• The creation is rejected if a COBA2P8 or COBA4P12 is already equipped
Example of Command Execution:Create ETHCON:NAME=RACK:0/ETHCON:0;
DELETE ETHCON
Command Tree:“MANAGED-ELEMENT h BSS-EQUIPMENT h BTSEP h RACK h ETHCON h DELETE ETHCON”
Applicability:Phase 2.
Visibility level: 2.
Command Description:This command deletes the ETHCON (ETHernet CONnection) board from the BTSE data base.
Long Names:NAME Address of the managed object
System Responses:Operation Completed
After command execution, a message of Changed Configuration Notification is dis-played. A further message indicates the result of the operation. An example of delete command is the following:
JOB: 32
DELETE ETHCON NAME=RACK:0..7/ETHCON:0..0;
358DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805b1091
ETHCON
PC Time&Date: 09.10.2008 09:41:07 +02:00
NE Time&Date: 01.01.1990 00:03:16 +00:00
USER NAME: NSN_Paul
COMMAND: Delete ETHCON:NAME=RACK:0/ETHCON:0;
SW RELEASE: 03-04-19-06-11-06_08-10-08
COMMAND RESULT:Operation successful
END OF OUTPUT FOR JOB 32
Operation Failed
None.
Application Guidelines:
• The deletion is rejected as long as an ETHPORT and/or CESTUNNEL object exists.
Example of Command Execution:Delete ETHCON:NAME=RACK:0/ETHCON:0;
GET ETHCON
Command Tree:“MANAGED-ELEMENT h BSS-EQUIPMENT h BTSEP h RACK h ETHCON h GET ETHCON”
Applicability:Phase 2 and Phase 3.
Visibility level: 0.
Command Description:This command displays the attributes of the ETHCON.
Long Names:NAME Address of the managed object
REQATTL Required attribute list
ALS alarmStatus
AST administrativeState
AVS availabilityStatus
OST operationalState
PRS proceduralStatus
FWVER firmwareVersion
RELFUNCOBJ relatedFuncObjects
MONPRT monitoringPort
GET ETHCON NAME=RACK:0..7/ETHCON:0..0 [,REQATTL=ALS, AST, AVS, OST, PRS, FWVER, RELFUNCOBJ, MONPRT];
DN0933412 Issue 01359
BTSplus mainline commands at the Flexi BSC product family
ETHCON
Id:0900d805805b1091
System Responses:Operation Completed
After command execution, a message of Changed Configuration Notification is dis-played. A further message indicates the result of the operation. A message indicates the result of the operation. An example of get command is the following:
JOB: 24
PC Time&Date: 09.10.2008 09:40:41 +02:00
NE Time&Date: 01.01.1990 00:02:50 +00:00
USER NAME: NSN_Paul
COMMAND: Get ETHCON:NAME=RACK:0/ETHCON:0;
SW RELEASE: 03-04-19-06-11-06_08-10-08
COMMAND RESULT:Operation successful
alarmStatus = CLEARED
administrativeState = Unlocked
availabilityStatus = NULL.
operationalState = ENABLED
proceduralStatus = NULL
relatedFuncObjects = Null
monitoringPort = none
END OF OUTPUT FOR JOB 24
Operation Failed
None.
Application Guidelines:None.
Example of Command Execution:Get ETHCON:NAME=RACK:0/ETHCON:0,REQATTL=ALS&AST&AVS&OST& PRS& RELFUNCOBJ& MONPRT;
LOCK ETHCON
Command Tree:“MANAGED-ELEMENT h BSS-EQUIPMENT h BTSEP h RACK h ETHCON h LOCK ETHCON”
Applicability:Phase 2.
Visibility level: 1.
Command Description:This command changes the administrative state of the ETHCON board.
LOCK ETHCON NAME=RACK:0..7/ETHCON:0..0;
360DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805b1091
ETHCON
Long Names:NAME Address of the managed object
System Responses:Operation Completed
The specified change of administrative state has been perfomed:
JOB: 19
PC Time&Date: 09.10.2008 09:40:20 +02:00
NE Time&Date: 01.01.1990 00:02:29 +00:00.
USER NAME: NSN_Paul
COMMAND: Lock ETHCON:NAME=RACK:0/ETHCON:0;
SW RELEASE: 03-04-19-06-11-06_08-10-08
COMMAND RESULT:Operation successful
administrativeState = Locked
END OF OUTPUT FOR JOB 19
Operation Failed
None.
Application Guidelines:None.
Example of Command Execution:Lock ETHCON:NAME=RACK:0/ETHCON:0;
SET ETHCON
Command Tree:“MANAGED-ELEMENT h BSS-EQUIPMENT h BTSEP h RACK h ETHCON h SET ETHCON”
Applicability:Phase 2 and Phase 3.
Visibility level: 2.
Command Description:This command sets the attributes of ETHCON board to the BTSE data base.
Long Names:NAME Address of the managed object
MONPRT monitoringPort
System Responses:Operation Completed
SET ETHCON NAME=RACK:0..7/ETHCON:0..0 [,MONPRT=];
DN0933412 Issue 01361
BTSplus mainline commands at the Flexi BSC product family
ETHCON
Id:0900d805805b1091
After command execution, a message of Changed Attribute Event Report is displayed. A further message indicates the result of the operation. An example of set command is the following:
JOB: 26.
PC Time&Date: 09.10.2008 09:40:57 +02:00
NE Time&Date: 01.01.1990 00:03:06 +00:00
USER NAME: NSN_Paul
COMMAND: Set ETHCON:NAME=RACK:0/ETHCON:0,MONPRT=coba;
SW RELEASE: 03-04-19-06-11-06_08-10-08
COMMAND RESULT:Operation successful
monitoringPort = coba
END OF OUTPUT FOR JOB 26
Operation Failed
None.
Application Guidelines:None.
Example of Command Execution:Set ETHCON:NAME=RACK:0/ETHCON:0,MONPRT=none;
UNLOCK ETHCON
Command Tree:“MANAGED-ELEMENT h BSS-EQUIPMENT h BTSEP h RACK h ETHCON h UNLOCK ETHCON”
Applicability:Phase 2.
Visibility level: 1.
Command Description:This command changes the administrative state of the ETHCON board.
Long Names:NAME Address of the managed object
System Responses:Operation Completed
The specified change of administrative state has been perfomed:
JOB: 21
PC Time&Date: 09.10.2008 09:40:25 +02:00
NE Time&Date: 01.01.1990 00:02:34 +00:00
USER NAME: NSN_Paul
UNLOCK ETHCON NAME=RACK:0..7/ETHCON:0..0;
362DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805b1091
ETHCON
COMMAND: Unlock ETHCON:NAME=RACK:0/ETHCON:0;
SW RELEASE: 03-04-19-06-11-06_08-10-08
COMMAND RESULT:Operation successful
administrativeState = Unlocked
END OF OUTPUT FOR JOB 21
Operation Failed
None.
Application Guidelines:None.
Example of Command Execution:Unlock ETHCON:NAME=RACK:0/ETHCON:0;
DN0933412 Issue 01363
BTSplus mainline commands at the Flexi BSC product family
ETHPORT
Id:0900d805805b1093
ETHPORTThe ETHPORT object is introduced to indicate the state of the Ethernet port and to allow the configuration of port specific attributes. There is no ETHPORT instance for Ethernet ports which are not externally visible (connection to COBA) nor used for monitoring.
The Ethernet port supports full duplex mode.
CREATE ETHPORT
Command Tree:“MANAGED-ELEMENT h BSS-EQUIPMENT h BTSEP h ETHPORT h CREATE ETHPORT”
Applicability:Phase 2 and Phase 3.
Visibility level: 2.
Command Description:This command adds the ETHPORT to the BTSE data base.
Long Names:NAME Address of the managed object
EAUTONEG enableAutoNegotiation
EFLWCTRL enableFlowControl
PUSG portUsage
System Responses:Operation Completed
After command execution, a message of Changed Configuration Notification is dis-played. A further message indicates the result of the operation. An example of create command is the following:
JOB: 39
PC Time&Date: 08.02.2008 13:20:45 +01:00
NE Time&Date: 01.01.1990 00:47:41 +00:00
USER NAME: NSN
COMMAND: Create ETHPORT:NAME=ETHPORT:0;
SW RELEASE: 01-04-19-01-01-CR_08-02-08.
COMMAND RESULT:Operation successful
END OF OUTPUT FOR JOB 39
Operation Failed
None.
CREATE ETHPORT NAME=ETHPORT:0..3 [,EAUTONEG=] [,EFLWCTRL=] ,PUSG=;
364DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805b1093
ETHPORT
Application Guidelines:
• Default values apply for the typical Abis Ethernet configuration • An ETHPORT object can be only created if the ETHCON object has been created
before. Physical ports of the Ethernet switch without related ETHPORT object (except for the monitoring port(s)) are blocked
Example of Command Execution:Create ETHPORT:NAME=ETHPORT:0,EAUTONEG=TRUE,EFLWC-TRL=FALSE,PUSG=null;
DELETE ETHPORT
Command Tree:“MANAGED-ELEMENT h BSS-EQUIPMENT h BTSEP h ETHPORT h DELETE ETHPORT”
Applicability:Phase 2 and Phase 3.
Visibility level: 2.
Command Description:This command deletes the ETHPORT from the BTSE data base.
Long Names:NAME Address of the managed object
System Responses:Operation Completed
A further message indicates the result of the operation. An example of delete command is the following:
JOB: 39
PC Time&Date: 30.05.2008 11:00:01 +02:00
NE Time&Date: 01.01.1990 00:04:34 +00:00?
USER NAME: NSN ?
COMMAND: Delete ETHPORT:NAME=ETHPORT:0;?
SW RELEASE: 01-04-19-01-01-ZS_08-05-29?
COMMAND RESULT:Operation successful?
END OF OUTPUT FOR JOB 39?
Operation Failed
None.
Application Guidelines:None.
DELETE ETHPORT NAME=ETHPORT:0..3;
DN0933412 Issue 01365
BTSplus mainline commands at the Flexi BSC product family
ETHPORT
Id:0900d805805b1093
Example of Command Execution:Delete ETHPORT:NAME=ETHPORT:0;
GET ETHPORT
Command Tree:“MANAGED-ELEMENT h BSS-EQUIPMENT h BTSEP h ETHPORT h GET ETHPORT”
Applicability:Phase 2 and Phase 3.
Visibility level: 0.
Command Description:This command displays the attributes of the ETHPORT.
Long Names:NAME Address of the managed object
REQATTL Required attribute list
ALS alarmStatus
AST administrativeState
AVS availabilityStatus
OST operationalState
PRS proceduralStatus
RELFUNCOBJ relatedFuncObjects
EAUTONEG enableAutoNegotiation
EFLWCTRL enableFlowControl
MTYP mediaType
PSTAT portStatus
PUSG portUsage
SFPSERID sfpSerialId
System Responses:Operation Completed
A message indicates the result of the operation. An example of get command is the fol-lowing:
JOB: 58
PC Time&Date: 09.10.2008 09:43:52 +02:00
NE Time&Date: 01.01.1990 00:06:01 +00:00
USER NAME: NSN
GET ETHPORT NAME=ETHPORT:0..3 [,REQATTL=ALS, AST, AVS, OST, PRS, RELFUNCOBJ, EAUTONEG, EFLWCTRL, MTYP, PSTAT, PUSG, SFPSERID];
366DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805b1093
ETHPORT
COMMAND: Get ETHPORT:NAME=ETHPORT:0;
SW RELEASE: 03-04-19-06-11-06_08-10-08
COMMAND RESULT: Operation successful
alarmStatus = CLEARED
administrativeState = Unlocked
availabilityStatus = NULL
operationalState = ENABLED
proceduralStatus = NULL
relatedFuncObjects = Null
enableAutoNegotiation = TRUE
enableFlowControl = FALSE
mediaType = electrical
portStatus =
speed = speed100M
duplexMode = enabled
flowControl = disabled
portUsage = bscLink
sfpSerialId = Null
END OF OUTPUT FOR JOB 58
Operation Failed
None.
Application Guidelines:None.
Example of Command Execution:Get ETHPORT:NAME=ETHPORT:0,REQATTL=ALS&AST&AVS&OST&PRS&REL-FUNCOBJ&EAUTONEG&EFLWCTRL&MTYP&PSTAT&PUSG&SPFSERID;
LOCK ETHPORT
Command Tree:“MANAGED-ELEMENT h BSS-EQUIPMENT h BTSEP h ETHPORT h LOCK ETHPORT”
Applicability:Phase 2 and Phase 3.
Visibility level: 1.
Command Description:This command changes the administrative state of ETHPORT.
LOCK ETHPORT NAME=ETHPORT:0..3;
DN0933412 Issue 01367
BTSplus mainline commands at the Flexi BSC product family
ETHPORT
Id:0900d805805b1093
Long Names:NAME Address of the managed object
System Responses:Operation Completed
The specified change of administrative state has been perfomed.
JOB: 49
PC Time&Date: 27.08.2008 14:16:31 +02:00
NE Time&Date: 27.08.2008 14:05:17 +01:00
USER NAME: NSN
COMMAND: Lock ETHPORT:NAME=ETHPORT:0;
SW RELEASE: 01-04-19-01-11-ZT_08-08-23
COMMAND RESULT:Operation successful
administrativeState = Locked
END OF OUTPUT FOR JOB 49
Operation Failed
None.
Application Guidelines:None.
Example of Command Execution:Lock ETHPORT:NAME=ETHPORT:0;
SET ETHPORT
Command Tree:“MANAGED-ELEMENT h BSS-EQUIPMENT h BTSEP h ETHPORT h SET ETHPORT”
Applicability:Phase 2 and Phase 3.
Visibility level: 2.
Command Description:This command sets the attributes of ETHPORT to the BTSE data base.
Long Names:NAME Address of the managed object
EAUTONEG enableAutoNegotiation
EFLWCTRL enableFlowControl
PUSG portUsage
SET ETHPORT NAME=ETHPORT:0..3 [,EAUTONEG=] [,EFLWCTRL=] [,PUSG=];
368DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805b1093
ETHPORT
System Responses:Operation Completed
A message indicates the result of the operation. An example of get command is the fol-lowing:
JOB: 59
PC Time&Date: 09.10.2008 09:44:20 +02:00
NE Time&Date: 01.01.1990 00:06:29 +00:00
USER NAME: NSN
COMMAND: Set ETHPORT:NAME=ETHPORT:0,EAUTONEG=TRUE,EFLWC-TRL=FALSE,PUSG=bscLink;
SW RELEASE: 03-04-19-06-11-06_08-10-08
COMMAND RESULT: Operation failed
enableAutoNegotiation = TRUE
enableFlowControl = FALSE
portUsage = bscLink
MO or MOT not locked (-151)
END OF OUTPUT FOR JOB 59
Operation Failed
None.
Application Guidelines:None.
Example of Command Execution:Set ETHPORT:NAME=ETHPORT:0,EAUTONEG=TRUE,EFLWC-TRL=FALSE,PUSG=null;
UNLOCK ETHPORT
Command Tree:“MANAGED-ELEMENT h BSS-EQUIPMENT h BTSEP h ETHPORT h UNLOCK ETHPORT”
Applicability:Phase 2 and Phase 3.
Visibility level: 1.
Command Description:This command changes the administrative state of ETHPORT.
Long Names:NAME Address of the managed object
UNLOCK ETHPORT NAME=ETHPORT:0..3;
DN0933412 Issue 01369
BTSplus mainline commands at the Flexi BSC product family
ETHPORT
Id:0900d805805b1093
System Responses:Operation Completed
The specified change of administrative state has been perfomed.
JOB: 52
PC Time&Date: 27.08.2008 14:16:56 +02:00
NE Time&Date: 27.08.2008 14:05:42 +01:00
USER NAME: NSN
COMMAND: Unlock ETHPORT:NAME=ETHPORT:0;
SW RELEASE: 01-04-19-01-11-ZT_08-08-23
COMMAND RESULT:Operation successf
administrativeState = Unlocked
END OF OUTPUT FOR JOB 52
Operation Failed
None.
Application Guidelines:None.
Example of Command Execution:Unlock ETHPORT:NAME=ETHPORT:0;
370DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805b1095
F6DCTMA
F6DCTMAThis object represents the TMA power supply of one antenna port. The functionality of the object is identical to the DUDCTMA object of an MFDUAMCO.
CREATE F6DCTMA
Command Tree:“MANAGED-ELEMENT h BSS-EQUIPMENT h BTSEP h RACK h F6DCTMA h CREATE F6DCTMA”
Applicability:Phase 2 and Phase 3.
Visibility level: 2.
Command Description:This command adds the F6DCTMA to the BTSE data base.
Long Names:NAME Address of the managed object
System Responses:Operation Completed
After command execution, a message of Changed Configuration Notification is dis-played. A further message indicates the result of the operation.
JOB: 288
PC Time&Date: 17.10.2008 09:24:24 +02:00
NE Time&Date: 01.01.1990 19:05:33 +00:00
USER NAME: NSN
COMMAND: Create F6DCTMA:NAME=RACK:0/F6DCTMA:0;
SW RELEASE: 01-04-19-01-11-07_08-10-16
COMMAND RESULT:Operation successful
END OF OUTPUT FOR JOB 288
Operation Failed
The specified object has not been created. In addition to the general NACK causes, a specific NACK cause, which indicates that the command is inconsistent with the physical configuration, is possible. An example is the following:
JOB: 34
PC Time&Date: 25.09.2008 14:46:58 +02:00
NE Time&Date: 02.01.1990 00:03:39 +00:00
USER NAME: NSN
COMMAND: Create F6DCTMA:NAME=RACK:0/F6DCTMA:0;
SW RELEASE: 03-04-19-01-11-05_08-09-24
CREATE F6DCTMA NAME=RACK:0..7/F6DCTMA:0..3;
DN0933412 Issue 01371
BTSplus mainline commands at the Flexi BSC product family
F6DCTMA
Id:0900d805805b1095
COMMAND RESULT:Operation failed
Creation out of sequence (-162)
END OF OUTPUT FOR JOB 34
None.
Application Guidelines:None.
Example of Command Execution:Create F6DCTMA:NAME=RACK:0/F6DCTMA:0;
DELETE F6DCTMA
Command Tree:“MANAGED-ELEMENT h BSS-EQUIPMENT h BTSEP h RACK h F6DCTMA h DELETE F6DCTMA”
Applicability:Phase 2 and Phase 3.
Visibility level: 2.
Command Description:This command deletes the F6DCTMA to the BTSE data base.
Long Names:NAME Address of the managed object
System Responses:Operation Completed
After command execution, a message of Changed Configuration Notification is dis-played. A further message indicates the result of the operation. An example of delete command is the following:
JOB: 59
PC Time&Date: 17.10.2008 09:05:13 +02:00
NE Time&Date: 01.01.1990 18:46:22 +00:00
USER NAME: NSN
COMMAND: Delete F6DCTMA:NAME=RACK:0/F6DCTMA:0;
SW RELEASE: 01-04-19-01-11-07_08-10-16
COMMAND RESULT:Operation successful
END OF OUTPUT FOR JOB 59
Operation Failed
The specified Object has not been deleted. In addition to the general NACK causes, a specific NACK cause, which indicates that the command is inconsistent with the physical configuration, is possible. An example is the following:
DELETE F6DCTMA NAME=RACK:0..7/F6DCTMA:0..3;
372DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805b1095
F6DCTMA
JOB: 137
PC Time&Date: 24.09.2008 15:06:31 +02:00
NE Time&Date: 01.01.1990 00:23:14 +00:00
USER NAME: NSN
COMMAND: Delete F6DCTMA:NAME=RACK:0/F6DCTMA:0;
SW RELEASE: 03-04-19-01-11-05_08-09-24
COMMAND RESULT:Operation failed
MO or MOT not locked (-151)
END OF OUTPUT FOR JOB 137.
Application Guidelines:None.
Example of Command Execution:Delete F6DCTMA:NAME=RACK:0/F6DCTMA:0;
GET F6DCTMA
Command Tree:“MANAGED-ELEMENT h BSS-EQUIPMENT h BTSEP h RACK h F6DCTMA h GET F6DCTMA”
Applicability:Phase 2 and Phase 3.
Visibility level: 0.
Command Description:This command displays the attributes of F6DCTMA.
Long Names:NAME Address of the managed object
REQATTL Required attribute list
ALS alarmStatus
AST administrativeState
AVS availabilityStatus
OST operationalState
PRS proceduralStatus
RELFUNCOBJ relatedFuncObjects
System Responses:Operation Completed
A message indicates the result of the operation. An example of get command is the fol-lowing:
GET F6DCTMA NAME=RACK:0..7/F6DCTMA:0..3 [,REQATTL=ALS, AST, AVS, OST, PRS, RELFUNCOBJ];
DN0933412 Issue 01373
BTSplus mainline commands at the Flexi BSC product family
F6DCTMA
Id:0900d805805b1095
JOB: 140
PC Time&Date: 16.09.2008 15:59:02 +02:00
NE Time&Date: 01.01.1990 00:19:44 +00:00
USER NAME: NSN
COMMAND: Get F6DCTMA:NAME=RACK:0/F6DCTMA:0;
SW RELEASE: 01-04-19-01-12-MB_08-09-16
COMMAND RESULT:Operation successful
alarmStatus = CLEARED
administrativeState = Unlocked
availabilityStatus = NotInstalled
operationalState = DISABLED
proceduralStatus = NULL
relatedFuncObjects = Null
END OF OUTPUT FOR JOB 140
Operation Failed
None.
Application Guidelines:None.
Example of Command Execution:Get F6DCTMA:NAME=RACK:0/F6DCTMA:0, REQATTL=ALS&AST&AVS&OST&PRS&&RELFUNCOBJ;
GETTEST F6DCTMA
Command Tree:“MANAGED-ELEMENT h BSS-EQUIPMENT h BTSEP h RACK h F6DCTMA h GETTEST F6DCTMA”
Applicability:Phase 2 and Phase 3.
Visibility level: 0.
Command Description:new information
Long Names:NAME Address of the managed object
REQATTL Required attribute list
System Responses:Operation Completed
GETTEST F6DCTMA NAME=RACK:0..7/F6DCTMA:0..3;
374DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805b1095
F6DCTMA
A message indicates the result of the operation.
JOB: 173
PC Time&Date: 28.10.2008 16:31:01 +01:00
NE Time&Date: 01.01.1990 00:21:30 +00:00
USER NAME: NSN
COMMAND: Gettest F6DCTMA:NAME=RACK:0/F6DCTMA:0;
SW RELEASE: 01-04-19-01-11-08_08-10-17
COMMAND RESULT:Operation successful
END OF OUTPUT FOR JOB 173
Operation Failed
The specified action cannot be performed. In addition to the general NACK causes, a specific NACK cause, which indicates that the command is inconsistent with the physical configuration, is possible. An example is the following:
JOB: 48
PC Time&Date: 17.10.2008 09:04:29 +02:00
NE Time&Date: 01.01.1990 18:45:38 +00:00
USER NAME: NSN
COMMAND: Gettest F6DCTMA:NAME=RACK:0/F6DCTMA:0;
SW RELEASE: 01-04-19-01-11-07_08-10-16
COMMAND RESULT:Operation failed
MOT = RACK:0/F6DCTMA:0
Object instance unknown or not allowed (-9)
END OF OUTPUT FOR JOB 48.
Application Guidelines:None.
Example of Command Execution:Gettest F6DCTMA:NAME=RACK:0/F6DCTMA:0;?
LOCK F6DCTMA
Command Tree:“MANAGED-ELEMENT h BSS-EQUIPMENT h BTSEP h RACK h F6DCTMA h LOCK F6DCTMA”
Applicability:Phase 2 and Phase 3.
Visibility level: 1.
Command Description:This command changes the administrative state of F6DCTMA.
LOCK F6DCTMA NAME=RACK:0..7/F6DCTMA:0..3;
DN0933412 Issue 01375
BTSplus mainline commands at the Flexi BSC product family
F6DCTMA
Id:0900d805805b1095
Long Names:NAME Address of the managed object
System Responses:Operation Completed.
The specified change of administrative state has been perfomed:
JOB: 40
PC Time&Date: 17.10.2008 09:04:19 +02:00
NE Time&Date: 01.01.1990 18:45:28 +00:00
USER NAME: NSN
COMMAND: Lock F6DCTMA:NAME=RACK:0/F6DCTMA:0;
SW RELEASE: 01-04-19-01-11-07_08-10-16
COMMAND RESULT:Operation successful
administrativeState = Locked
END OF OUTPUT FOR JOB 40
Operation Failed
None.
Application Guidelines:None.
Example of Command Execution:Perftest F6DCTMA:NAME=RACK:0/F6DCTMA:0;
PERFTEST F6DCTMA
Command Tree:“MANAGED-ELEMENT h BSS-EQUIPMENT h BTSEP h RACK h F6DCTMA h PERFTEST F6DCTMA”
Applicability:Phase 2 and Phase 3.
Visibility level: 1.
Command Description:This command is used to start an asynchronous test in the object.
Long Names:NAME Address of the managed object
System Responses:Operation Completed
Test configuration has been set and the specified test has been started. An example is the following:
PERFTEST F6DCTMA NAME=RACK:0..7/F6DCTMA:0..3;
376DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805b1095
F6DCTMA
JOB: 43
PC Time&Date: 17.10.2008 09:04:27 +02:00
NE Time&Date: 01.01.1990 18:45:36 +00:00
USER NAME: NSN
COMMAND: Perftest F6DCTMA:NAME=RACK:0/F6DCTMA:0;
SW RELEASE: 01-04-19-01-11-07_08-10-16
COMMAND RESULT:Operation successful
MOT = RACK:0/F6DCTMA:0
tO = BTSETEST:1
END OF OUTPUT FOR JOB 43Operation Failed
The specified test cannot be performed. In addition to the general NACK causes, a specific NACK cause, which indicates that the command is inconsistent with the physical configuration, is possible. An example is the following:
JOB: 140
PC Time&Date: 24.09.2008 15:06:41 +02:00
NE Time&Date: 01.01.1990 00:23:24 +00:00
USER NAME: NSN
COMMAND: Perftest F6DCTMA:NAME=RACK:0/F6DCTMA:0;
SW RELEASE: 03-04-19-01-11-05_08-09-24
COMMAND RESULT:Operation failed
MOT = RACK:0/F6DCTMA:0
Physical configuration cannot be performed (-30)
END OF OUTPUT FOR JOB 140
Application Guidelines:None.
Example of Command Execution:Perftest F6DCTMA:NAME=RACK:0/F6DCTMA:0;
STOPTEST F6DCTMA
Command Tree:“MANAGED-ELEMENT h BSS-EQUIPMENT h BTSEP h RACK h F6DCTMA h STOPTEST F6DCTMA”
Applicability:Phase 2 and Phase 3.
Visibility level: 1.
Command Description:This command is used to stop a diagnostic previously started.
STOPTEST F6DCTMA NAME=RACK:0..7/F6DCTMA:0..3;
DN0933412 Issue 01377
BTSplus mainline commands at the Flexi BSC product family
F6DCTMA
Id:0900d805805b1095
Long Names:NAME Address of the managed object
System Responses:Operation Completed
Test has been stopped. The System Responses will not be addressed to the MOT but to the object.STOPTEST F6DCTMA NAME=RACK:0..7/F6DCTMA:0..3;Result TEST:
name = TEST:<n>
testOutcome = inconclusive
mOts = It is the identifier of the hardware object under test.
testTermination = CancelexecutedPhases
phaseId = It represents the list of the executed test phases; the list is not shown for test in the waiting list (queued)
failedPhases
phaseId = It represents the list of the failed test phase
phaseId = additional information is provided for each phase....
skippedPhases
phaseId = It represents the list of the skipped phases; the list is not shown for test in the waiting list (queued).
phaseId
Operation Failed
The specified test cannot be stopped. In addition to the general NACK causes, a specific NACK cause, which indicates that the command is inconsistent with the physical config-uration, is possible. An example is the following:
JOB: 55
PC Time&Date: 17.10.2008 09:04:59 +02:00
NE Time&Date: 01.01.1990 18:46:08 +00:00
USER NAME: NSN
COMMAND: Stoptest F6DCTMA:NAME=RACK:0/F6DCTMA:0;
SW RELEASE: 01-04-19-01-11-07_08-10-16
COMMAND RESULT:Operation failed
MOT = RACK:0/F6DCTMA:0
Object instance unknown or not allowed (-9)
END OF OUTPUT FOR JOB 55.
Application Guidelines:None.
Example of Command Execution:Stoptest F6DCTMA:NAME=RACK:0/F6DCTMA:0;
378DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805b1095
F6DCTMA
UNLOCK F6DCTMA
Command Tree:“MANAGED-ELEMENT h BSS-EQUIPMENT h BTSEP h RACK h F6DCTMA h UNLOCK F6DCTMA”
Applicability:Phase 2 and Phase 3.
Visibility level: 1.
Command Description:This command changes the administrative state of F6DCTMA object.
Long Names:NAME Address of the managed object
System Responses:Operation Completed
The specified change of administrative state has been perfomed:
JOB: 56
PC Time&Date: 17.10.2008 09:05:06 +02:00
NE Time&Date: 01.01.1990 18:46:15 +00:00
USER NAME: NSN
COMMAND: Unlock F6DCTMA:NAME=RACK:0/F6DCTMA:0;
SW RELEASE: 01-04-19-01-11-07_08-10-16
COMMAND RESULT:Operation successful
administrativeState = Unlocked
END OF OUTPUT FOR JOB 56
Operation Failed
None.
Application Guidelines:None.
Example of Command Execution:Unlock F6DCTMA:NAME=RACK:0/F6DCTMA:0;
UNLOCK F6DCTMA NAME=RACK:0..7/F6DCTMA:0..3;
DN0933412 Issue 01379
BTSplus mainline commands at the Flexi BSC product family
F6LNA
Id:0900d805805b1099
F6LNAThe F6LNA object integrates the HW functionality of both DILNA and DULNA objects.
CREATE F6LNA
Command Tree:“MANAGED-ELEMENT h BSS-EQUIPMENT h BTSEP h RACK h F6LNA h CREATE F6LNA”
Applicability:Phase 2 and Phase 3.
Visibility level: 2.
Command Description:This command adds the F6LNA to the BTSE data base.
Long Names:NAME Address of the managed object
CELLNO cellNumber
SCELLNO secondCellNumber
GNADB gainAdjustDb
LNAPRED lnaPredecessor
WDLNA wiringDataLna
LNAMDB lnaModeDb
System Responses:Operation Completed
After command execution, a message of Changed Configuration Notification is dis-played. A further message indicates the result of the operation. An example of create command is the following:
JOB: 71
PC Time&Date: 26.09.2008 13:12:42 +02:00
NE Time&Date: 26.09.2008 10:20:00 +01:00
USER NAME: NSN
COMMAND: Create
F6LNA:NAME=RACK:0/F6LNA:1,CELLNO=1,WDLNA=FCUMAIN1N;
SW RELEASE: 03-04-19-01-11-05_08-09-24
COMMAND RESULT:Operation successful.
cellNumber = 1
wiringDataLna = FCUMAIN1N
END OF OUTPUT FOR JOB 71
CREATE F6LNA NAME=RACK:0..7/F6LNA:0..3 ,CELLNO= [,SCELLNO=] [,GNADB=] [,LNAPRED=] ,WDLNA= [,LNAMDB=];
380DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805b1099
F6LNA
Operation Failed
The specified Object has not been created. In addition to the general NACK causes, a specific NACK cause, which indicates that the command is inconsistent with the physical configuration, is possible. An example is the following:
JOB: 9
PC Time&Date: 25.09.2008 14:46:05 +02:00
NE Time&Date: 02.01.1990 00:02:46 +00:00
USER NAME: NSN
COMMAND: Create
F6LNA:NAME=RACK:0/F6LNA:1,CELLNO=0,GNADB=N_00,LNAPRED=TMA(RACK
0-TMA1),WDLNA=CU0D;
SW RELEASE: 03-04-19-01-11-05_08-09-24
COMMAND RESULT:Operation failed
cellNumber = 0
gainAdjustDb = N_00
lnaPredecessor =
predType =
TMA
predRack = RACK0
predNo = TMA1
wiringDataLna = CU0D
Message cannot be performed (-17)
END OF OUTPUT FOR JOB 9
Application Guidelines:F6LNA creation attempts with more than 6 wiring paths specified in “wiringDataLna” attribute are rejected by BTS SW.
Example of Command Execution:Create F6LNA:NAME=RACK:0/F6LNA:1,CELLNO=1,WDLNA=FCUMAIN1N.
DELETE F6LNA
Command Tree:“MANAGED-ELEMENT h BSS-EQUIPMENT h BTSEP h RACK h F6LNA h DELETE F6LNA”
Applicability:Phase 2 and Phase 3.
Visibility level: 2.
DELETE F6LNA NAME=RACK:0..7/F6LNA:0..3;
DN0933412 Issue 01381
BTSplus mainline commands at the Flexi BSC product family
F6LNA
Id:0900d805805b1099
Command Description:This command deletes the F6LNA to the BTSE data base.
Long Names:NAME Address of the managed object
System Responses:Operation Completed
After command execution, a message of Changed Configuration Notification is dis-played. A further message indicates the result of the operation. An example of delete command is the following:
JOB: 29
PC Time&Date: 25.09.2008 14:46:53 +02:00
NE Time&Date: 02.01.1990 00:03:34 +00:00
USER NAME: NSN
COMMAND: Delete F6LNA:NAME=RACK:0/F6LNA:0;
SW RELEASE: 03-04-19-01-11-05_08-09-24
COMMAND RESULT:Operation successful
END OF OUTPUT FOR JOB 29.
Operation Failed
None.
Application Guidelines:None.
Example of Command Execution:Delete F6LNA:NAME=RACK:0/F6LNA:0;
GET F6LNA
Command Tree:“MANAGED-ELEMENT h BSS-EQUIPMENT h BTSEP h RACK h F6LNA h GET F6LNA”
Applicability:Phase 2 and Phase 3.
Visibility level: 0.
Command Description:This command displays the attributes of F6LNA object.
GET F6LNA NAME=RACK:0..7/F6LNA:0..3 [,REQATTL=ALS, AST, OST, PRS, AVS, CELLNO, SCELLNO, GNA, GNADB, LNAPRED, WDLNA, LNAMDB, LNAMODE, RELFUN-COBJ];
382DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805b1099
F6LNA
Long Names:NAME Address of the managed object
REQATTL Required attribute list
ALS alarmStatus
AST administrativeState
OST operationalState
PRS proceduralStatus
AVS availabilityStatus
CELLNO cellNumber
SCELLNO secondCellNumber
GNA gainAdjust(dB)
GNADB gainAdjustDb
LNAPRED lnaPredecessor
WDLNA wiringDataLna
LNAMDB lnaModeDb
LNAMODE lnaMode
RELFUNCOBJ relatedFuncObjects
System Responses:Operation Completed
A message indicates the result of the operation. An example of get command is the fol-lowing:
JOB: 60
PC Time&Date: 17.10.2008 09:05:21 +02:00
NE Time&Date: 01.01.1990 18:46:30 +00:00
USER NAME: NSN
COMMAND: Get F6LNA:NAME=RACK:0/F6LNA:0;
SW RELEASE: 01-04-19-01-11-07_08-10-16
COMMAND RESULT:Operation successful
alarmStatus = CLEARED
administrativeState = Unlocked
operationalState = ENABLED
proceduralStatus = NULL
availabilityStatus = NULL
cellNumber = 0
secondCellNumber = NotUsed
gainAdjust(dB) = N_00
gainAdjustDb = DIP
lnaPredecessor = Null
wiringDataLna = CU0N & CU1N & CU2N & CU3N
DN0933412 Issue 01383
BTSplus mainline commands at the Flexi BSC product family
F6LNA
Id:0900d805805b1099
lnaModeDb = DIP.
lnaMode = AMCO_MODE
relatedFuncObjects = Null
END OF OUTPUT FOR JOB 60
Operation Failed
None.
Application Guidelines:None.
Example of Command Execution:Get F6LNA:NAME=RACK:0/F6LNA:0;REQATTL= ALS& AST& OST& PRS& AVS&CELLNO& SCELLNO& GNA& GNADB&LNAPRED& WDLNA& LNAMDB& NAMODE& RELFUNCOBJ;
GETTEST F6LNA
Command Tree:“MANAGED-ELEMENT h BSS-EQUIPMENT h BTSEP h RACK h F6LNA h GETTEST F6LNA”
Applicability:Phase 2 and Phase 3.
Visibility level: 0.
Command Description:This command displays the attributes of the object test.
Long Names:NAME Address of the managed object
REQATTL Required attribute list
System Responses:Operation Completed
A message indicates the result of the operation. An example of gettest command is the following:
JOB: 273
PC Time&Date: 17.10.2008 09:21:19 +02:00
NE Time&Date: 01.01.1990 19:02:28 +00:00
USER NAME: NSN
COMMAND: Gettest F6LNA:NAME=RACK:0/F6LNA:1;.
SW RELEASE: 01-04-19-01-11-07_08-10-16
COMMAND RESULT:Operation successful
END OF OUTPUT FOR JOB 273
GETTEST F6LNA NAME=RACK:0..7/F6LNA:0..3;
384DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805b1099
F6LNA
Operation Failed
The GETTEST command has not been successfully executed. A general NACK will indicate possible errors or a specific NACK strictly related to the single command is pos-sible. An example of specific NACK is the following:
JOB: 69
PC Time&Date: 17.10.2008 09:05:40 +02:00
NE Time&Date: 01.01.1990 18:46:49 +00:00
USER NAME: NSN
COMMAND: Gettest F6LNA:NAME=RACK:0/F6LNA:0;
SW RELEASE: 01-04-19-01-11-07_08-10-16
COMMAND RESULT:Operation failed
MOT = RACK:0/F6LNA:0
Object instance unknown or not allowed (-9)
END OF OUTPUT FOR JOB 69e.
Application Guidelines:None.
Example of Command Execution:Gettest F6LNA:NAME=RACK:0/F6LNA:0;?
LOCK F6LNA
Command Tree:“MANAGED-ELEMENT h BSS-EQUIPMENT h BTSEP h RACK h F6LNA h LOCK F6LNA”
Applicability:Phase 2 and Phase 3.
Visibility level: 1.
Command Description:This command changes the administrative state of F6LNA.
Long Names:NAME Address of the managed object
System Responses:Operation Completed
After command execution, a message of Changed Configuration Notification is dis-played. A further message indicates the result of the operation. An example of lock command is the following:
JOB: 113
PC Time&Date: 28.10.2008 16:26:55 +01:00
LOCK F6LNA NAME=RACK:0..7/F6LNA:0..3;
DN0933412 Issue 01385
BTSplus mainline commands at the Flexi BSC product family
F6LNA
Id:0900d805805b1099
NE Time&Date: 01.01.1990 00:17:24 +00:00
USER NAME: NSN
COMMAND: Lock F6LNA:NAME=RACK:0/F6LNA:0;
SW RELEASE: 01-04-19-01-11-08_08-10-17
COMMAND RESULT:Operation successful
administrativeState = Locked
END OF OUTPUT FOR JOB 113.
Operation Failed
None.
Application Guidelines:None.
Example of Command Execution:Lock F6LNA:NAME=RACK:0/F6DCTMA:0;
PERFTEST F6LNA
Command Tree:“MANAGED-ELEMENT h BSS-EQUIPMENT h BTSEP h RACK h F6LNA h PERFTEST F6LNA”
Applicability:Phase 2 and Phase 3.
Visibility level: 1.
Command Description:This command is used to start an asynchronous test in the object.
Long Names:NAME Address of the managed object
System Responses:Operation Completed
After command execution, a message of Changed Configuration Notification is dis-played.? A further message indicates the result of the operation. An example of perftest? command is the following:
JOB: 13?
PC Time&Date: 26.09.2008 13:05:27 +02:00?
NE Time&Date: 26.09.2008 10:12:45 +01:00?
USER NAME: NSN ?
COMMAND: Perftest F6LNA:NAME=RACK:0/F6LNA:0;?
SW RELEASE: 03-04-19-01-11-05_08-09-24?
COMMAND RESULT:Operation successful?
PERFTEST F6LNA NAME=RACK:0..7/F6LNA:0..3;
386DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805b1099
F6LNA
MOT = RACK:0/F6LNA:0?
tO = BTSETEST:7?
END OF OUTPUT FOR JOB 13?.
Operation Failed
The specified test cannot be performed. In addition to the general NACK causes, a specific NACK cause, which indicates that the command is inconsistent with the physical configuration, is possible. An example is the following:
JOB: 145
PC Time&Date: 16.09.2008 16:01:13 +02:00
NE Time&Date: 01.01.1990 00:21:55 +00:00
USER NAME: NSN
COMMAND: Perftest F6LNA:NAME=RACK:0/F6LNA:0;
SW RELEASE: 01-04-19-01-12-MB_08-09-16
COMMAND RESULT:Operation failed
MOT = RACK:0/F6LNA:0
MO or MOT not locked (-151)
END OF OUTPUT FOR JOB 145
Application Guidelines:None.
Example of Command Execution:Perftest F6LNA:NAME=RACK:0/F6DCTMA:0;
SET F6LNA
Command Tree:“MANAGED-ELEMENT h BSS-EQUIPMENT h BTSEP h RACK h F6LNA h SET F6LNA”
Applicability:Phase 2 and Phase 3.
Visibility level: 2.
Command Description:This command sets the attributes F6LNA obejct.
Long Names:NAME Address of the managed object
SCELLNO secondCellNumber
GNADB gainAdjustDb
WDLNA wiringDataLna
SET F6LNA NAME=RACK:0..7/F6LNA:0..3 [,SCELLNO=] [,GNADB=] [,WDLNA=] [,LNAMDB=];
DN0933412 Issue 01387
BTSplus mainline commands at the Flexi BSC product family
F6LNA
Id:0900d805805b1099
LNAMDB lnaModeDb
System Responses:Operation Completed
After command execution, a message of Changed Attribute Event Report is displayed. A further message indicates the result of the operation. An example of set command is the following:
JOB: 219.
PC Time&Date: 24.09.2008 14:37:37 +02:00
NE Time&Date: 24.09.2008 10:46:11 +00:00
USER NAME: NSN
COMMAND: Set F6LNA:NAME=RACK:0/F6LNA:0,GNADB=N_00;
SW RELEASE: 03-04-19-01-11-05_08-09-24
COMMAND RESULT:Operation successful
gainAdjustDb = N_00
END OF OUTPUT FOR JOB 219
Operation Failed
The specified object has not been set. In addition to the general NACK causes, a specific NACK cause, which indicates that the command is inconsistent with the physical configuration, is possible.
Application Guidelines:None.
Example of Command Execution:Set F6LNA:NAME=RACK:0/F6LNA:0,GNADB=N_00;
STOPTEST F6LNA
Command Tree:“MANAGED-ELEMENT h BSS-EQUIPMENT h BTSEP h RACK h F6LNA h STOPTEST F6LNA”
Applicability:Phase 2 and Phase 3.
Visibility level: 1.
Command Description:This command is used to stop a diagnostic previously started.
Long Names:NAME Address of the managed object
System Responses:Operation Completed
STOPTEST F6LNA NAME=RACK:0..7/F6LNA:0..3;
388DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805b1099
F6LNA
Test has been stopped. The System Responses will not be addressed to the MOT but to the object. An example of stoptest command is the following:
STOPTEST F6LNA NAME=RACK:0..7/F6LNA:0..3;
Result TEST:
name = TEST:<n>
testOutcome = inconclusive
mOts = It is the identifier of the hardware object under test.
testTermination = Cancel
executedPhases
phaseId = It represents the list of the executed test phases; the... list is not shown for test in the waiting list (queued)..failedPhases
phaseId = It represents the list of the failed test phase;
phaseId = additional information is provided for each phase..
skippedPhases
phaseId = It represents the list of the skipped phases;the list is
phaseId = not shown for test in the waiting list (queued).
Operation Failed
The specified test cannot be stopped. In addition to the general NACK causes, a specific NACK cause, which indicates that the command is inconsistent with the physical config-uration, is possible. An example is the following:
JOB: 274
PC Time&Date: 17.10.2008 09:21:25 +02:00
NE Time&Date: 01.01.1990 19:02:34 +00:00
USER NAME: NSN
COMMAND: Stoptest F6LNA:NAME=RACK:0/F6LNA:1;
SW RELEASE: 01-04-19-01-11-07_08-10-16
COMMAND RESULT:Operation failed
MOT = RACK:0/F6LNA:1
Object instance unknown or not allowed (-9)
END OF OUTPUT FOR JOB 274
Application Guidelines:None.
Example of Command Execution:Stoptest F6LNA:NAME=RACK:0/F6DCTMA:0;
UNLOCK F6LNAUNLOCK F6LNA NAME=RACK:0..7/F6LNA:0..3;
DN0933412 Issue 01389
BTSplus mainline commands at the Flexi BSC product family
F6LNA
Id:0900d805805b1099
Command Tree:“MANAGED-ELEMENT h BSS-EQUIPMENT h BTSEP h RACK h F6LNA h UNLOCK F6LNA”
Applicability:Phase 2 and Phase 3.
Visibility level: 1.
Command Description:This command changes the administrative state of F6LNA object.
Long Names:NAME Address of the managed object
System Responses:Operation Completed
After command execution, a message of Changed Configuration Notification is dis-played. A further message indicates the result of the operation. An example of unlock command is the following:
JOB: 18
PC Time&Date: 26.09.2008 13:06:03 +02:00
NE Time&Date: 26.09.2008 10:13:21 +01:00
USER NAME: NSN
COMMAND: Unlock F6LNA:NAME=RACK:0/F6LNA:0;
SW RELEASE: 03-04-19-01-11-05_08-09-24
COMMAND RESULT:Operation successful
administrativeState = Unlocked.
Operation Failed
None.
Application Guidelines:None.
Example of Command Execution:Unlock F6LNA:NAME=RACK:0/F6DCTMA:0;
390DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805b1029
F6TNFP
F6TNFPThis object provides the functionality to configure and supervise the turnable narrow-band filter of one TX path.
CREATE F6TNFP
Command Tree:“MANAGED-ELEMENT h BSS-EQUIPMENT h BTSEP h RACK h F6TNFP h CREATE F6TNFP”
Applicability:Phase 2 and Phase 3.
Visibility level: 2.
Command Description:This command adds the F6TNFP to the BTSE data base.
Long Names:NAME Address of the managed object
WDFTNFP wiringDataFtnfp
System Responses:Operation Completed
After command execution, a message of Changed Configuration Notification is dis-played. A further message indicates the result of the operation. An example of create command is the following:
JOB: 201
PC Time&Date: 17.10.2008 09:13:37 +02:00
NE Time&Date: 01.01.1990 18:54:46 +00:00
USER NAME: NSN
COMMAND: Create F6TNFP:NAME=RACK:0/F6TNFP:0,WDFTNFP=CU0-FVSWRP0;
SW RELEASE: 01-04-19-01-11-07_08-10-16
COMMAND RESULT:Operation successful
wiringDataFtnfp =
CUWiring = CU0
FVSWRPWiring = FVSWRP0.
END OF OUTPUT FOR JOB 201
Operation Failed
The specified Object has not been created. In addition to the general NACK causes, a specific NACK cause, which indicates that the command is inconsistent with the physical configuration, is possible.
CREATE F6TNFP NAME=RACK:0..7/F6TNFP:0..11 ,WDFTNFP=;
DN0933412 Issue 01391
BTSplus mainline commands at the Flexi BSC product family
F6TNFP
Id:0900d805805b1029
Application Guidelines:None.
Example of Command Execution:Create F6TNFP:NAME=RACK:0/F6TNFP:0,WDFTNFP=CU0-FVSWRP0;
DELETE F6TNFP
Command Tree:“MANAGED-ELEMENT h BSS-EQUIPMENT h BTSEP h RACK h F6TNFP h DELETE F6TNFP”
Applicability:Phase 2 and Phase 3.
Visibility level: 2.
Command Description:This command deletes the F6TNFP from the BTSE data base.
Long Names:NAME Address of the managed object
System Responses:Operation Completed
After command execution, a message of Changed Configuration Notification is dis-played. A further message indicates the result of the operation. An example of delete-command is the following:
JOB: 90
PC Time&Date: 17.10.2008 09:07:57 +02:00
NE Time&Date: 01.01.1990 18:49:06 +00:00
USER NAME: NSN
COMMAND: Delete F6TNFP:NAME=RACK:0/F6TNFP:0;
SW RELEASE: 01-04-19-01-11-07_08-10-16
COMMAND RESULT:Operation successful
END OF OUTPUT FOR JOB 90
Operation Failed
None.
Application Guidelines:None.
Example of Command Execution:Delete F6TNFP:NAME=RACK:0/F6TNFP:0;
DELETE F6TNFP NAME=RACK:0..7/F6TNFP:0..11;
392DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805b1029
F6TNFP
GET F6TNFP
Command Tree:“MANAGED-ELEMENT h BSS-EQUIPMENT h BTSEP h RACK h F6TNFP h GET F6TNFP”
Applicability:Phase 2 and Phase 3.
Visibility level: 0.
Command Description:This command displays the attributes of F6TNFP object.
Long Names:NAME Address of the managed object
REQATTL Required attribute list
ALS alarmStatus
AST administrativeState
AVS availabilityStatus
OST operationalState
PRS proceduralStatus
RELFUNCOBJ relatedFuncObjects
TNFTARGF tnfTargetFrequency
WDFTNFP wiringDataFtnfp
System Responses:Operation Completed
A message indicates the result of the operation. An example of get command is the fol-lowing:
JOB: 88
PC Time&Date: 17.10.2008 09:07:54 +02:00
NE Time&Date: 01.01.1990 18:49:03 +00:00
USER NAME: NSN
COMMAND: Get F6TNFP:NAME=RACK:0/F6TNFP:0;
SW RELEASE: 01-04-19-01-11-07_08-10-16
COMMAND RESULT:Operation successful
alarmStatus = CLEARED
administrativeState = Locked
availabilityStatus = Dependency
operationalState = DISABLED
proceduralStatus = NULL
GET F6TNFP NAME=RACK:0..7/F6TNFP:0..11 [,REQATTL=ALS, AST, AVS, OST, PRS, RELFUNCOBJ, TNFTARGF, WDFTNFP];
DN0933412 Issue 01393
BTSplus mainline commands at the Flexi BSC product family
F6TNFP
Id:0900d805805b1029
relatedFuncObjects = Null
tnfTargetFrequency = Null
CUWiring = CU0
FVSWRPWiring = FVSWRP0
END OF OUTPUT FOR JOB 88
Operation Failed
None.
Application Guidelines:None.
Example of Command Execution:Get F6TNFP:NAME=RACK:0/F6TNFP:0;
GETTEST F6TNFP
Command Tree:“MANAGED-ELEMENT h BSS-EQUIPMENT h BTSEP h RACK h F6TNFP h GETTEST F6TNFP”
Applicability:Phase 2 and Phase 3.
Visibility level: 0.
Command Description:This command displays the attributes of the object test.
Long Names:NAME Address of the managed object
REQATTL Required attribute list
System Responses:Operation Completed
A message indicates the result of the operation. An example of gettest command is the following:
JOB: 90
PC Time&Date: 29.10.2008 16:24:05 +01:00
NE Time&Date: 01.01.1990 00:14:34 +00:00
USER NAME: NSN
COMMAND: Gettest F6TNFP:NAME=RACK:0/F6TNFP:0;
SW RELEASE: 01-04-19-01-11-08_08-10-17
COMMAND RESULT:Operation successful
END OF OUTPUT FOR JOB 90
GETTEST F6TNFP NAME=RACK:0..7/F6TNFP:0..11;
394DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805b1029
F6TNFP
Operation Failed
The gettest command has not been successfully executed. A general NACK will indicate possible errors or a specific NACK strictly related to the single command is possible. An example is the following:
JOB: 85
PC Time&Date: 28.10.2008 16:24:05 +01:00
NE Time&Date: 01.01.1990 00:14:34 +00:00
USER NAME: NSN
COMMAND: Gettest F6TNFP:NAME=RACK:0/F6TNFP:0;
SW RELEASE: 01-04-19-01-11-08_08-10-17
COMMAND RESULT:Operation failed
MOT = RACK:0/F6TNFP:0
Object instance unknown or not allowed (-9)
END OF OUTPUT FOR JOB 85
Operation Failed
None.
Application Guidelines:None.
Example of Command Execution:Gettest F6TNFP:NAME=RACK:0/F6TNFP:0;
LOCK F6TNFP
Command Tree:“MANAGED-ELEMENT h BSS-EQUIPMENT h BTSEP h RACK h F6TNFP h LOCK F6TNFP”
Applicability:Phase 2 and Phase 3.
Visibility level: 1.
Command Description:This command changes the administrative state of F6TNFP.
Long Names:NAME Address of the managed object
System Responses:Operation Completed
The specified change of administrative state has been perfomed:
JOB: 153
PC Time&Date: 24.09.2008 15:14:50 +02:00
LOCK F6TNFP NAME=RACK:0..7/F6TNFP:0..11;
DN0933412 Issue 01395
BTSplus mainline commands at the Flexi BSC product family
F6TNFP
Id:0900d805805b1029
NE Time&Date: 01.01.1990 00:31:33 +00:00
USER NAME: NSN
COMMAND: Lock F6TNFP:NAME=RACK:0/F6TNFP:1;
SW RELEASE: 03-04-19-01-11-05_08-09-24
COMMAND RESULT:Operation successful
administrativeState = Locked
END OF OUTPUT FOR JOB 153
Operation Failed
None.
Application Guidelines:None.
Example of Command Execution:Lock F6TNFP:NAME=RACK:0/F6TNFP:1;
PERFTEST F6TNFP
Command Tree:“MANAGED-ELEMENT h BSS-EQUIPMENT h BTSEP h RACK h F6TNFP h PERFTEST F6TNFP”
Applicability:Phase 2 and Phase 3.
Visibility level: 1.
Command Description:This command is used to start an asynchronous test in the object.
Long Names:NAME Address of the managed object
System Responses:Operation Completed
Test configuration has been set and the specified test has been started.
JOB: 23
PC Time&Date: 26.09.2008 13:06:13 +02:00
NE Time&Date: 26.09.2008 10:13:31 +01:00
USER NAME: NSN
COMMAND: Perftest F6TNFP:NAME=RACK:0/F6TNFP:0;
SW RELEASE: 03-04-19-01-11-05_08-09-24
COMMAND RESULT:Operation successful
MOT = RACK:0/F6TNFP:0
PERFTEST F6TNFP NAME=RACK:0..7/F6TNFP:0..11;
396DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805b1029
F6TNFP
tO = BTSETEST:8
END OF OUTPUT FOR JOB 23
Operation FailedThe specified test cannot be performed. In addition to the general NACK causes, a specific NACK cause, which indicates that the command is inconsis-tent with the physical configuration, is possible.
Application Guidelines:None.
Example of Command Execution:Perftest F6TNFP:NAME=RACK:0/F6DCTMA:0;
STOPTEST F6TNFP
Command Tree:“MANAGED-ELEMENT h BSS-EQUIPMENT h BTSEP h RACK h F6TNFP h STOPTEST F6TNFP”
Applicability:Phase 2 and Phase 3.
Visibility level: 1.
Command Description:This command is used to stop a diagnostic previously started.
Long Names:NAME Address of the managed object
System Responses:Operation Completed
Test has been stopped. The System Responses are not be addressed to the MOT but to the object.
Operation Failed
The specified test has not been stopped. In addition to the general NACK causes, a specific NACK cause, which indicates that the command is inconsistent with the physical configuration, is possible. An example is the following:
JOB: 214
PC Time&Date: 17.10.2008 09:14:33 +02:00
NE Time&Date: 01.01.1990 18:55:42 +00:00
USER NAME: NSN
COMMAND: Stoptest F6TNFP:NAME=RACK:0/F6TNFP:0;
SW RELEASE: 01-04-19-01-11-07_08-10-16
COMMAND RESULT:Operation failed
MOT = RACK:0/F6TNFP:0
STOPTEST F6TNFP NAME=RACK:0..7/F6TNFP:0..11;
DN0933412 Issue 01397
BTSplus mainline commands at the Flexi BSC product family
F6TNFP
Id:0900d805805b1029
Object instance unknown or not allowed (-9)
END OF OUTPUT FOR JOB 214
Application Guidelines:None.
Example of Command Execution:Stoptest F6TNFP:NAME=RACK:0/F6DCTMA:0;
UNLOCK F6TNFP
Command Tree:“MANAGED-ELEMENT h BSS-EQUIPMENT h BTSEP h RACK h F6TNFP h UNLOCK F6TNFP”
Applicability:Phase 2 and Phase 3.
Visibility level: 1.
Command Description:This command changes the administrative state of F6LNA object.
Long Names:NAME Address of the managed object
System Responses:Operation Completed
The specified change of administrative state has been perfomed:
JOB: 93
PC Time&Date: 24.09.2008 14:21:38 +02:00
NE Time&Date: 24.09.2008 10:30:12 +00:00
USER NAME: NSN
COMMAND: Unlock F6TNFP:NAME=RACK:0/F6TNFP:0;
SW RELEASE: 03-04-19-01-11-05_08-09-24
COMMAND RESULT:Operation successful
administrativeState = Unlocked
END OF OUTPUT FOR JOB 93.
Operation Failed
None.
Application Guidelines:None.
Example of Command Execution:Unlock F6TNFP:NAME=RACK:0/F6DCTMA:0;
UNLOCK F6TNFP NAME=RACK:0..7/F6TNFP:0..11;
398DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805b102b
F6VSWRP
F6VSWRPThe F6VSWRP object models the common functions of one FICOM6. Its creation is therefore mandatory if the module is equipped.
CREATE F6VSWRP
Command Tree:“MANAGED-ELEMENT h BSS-EQUIPMENT h BTSEP h RACK h F6VSWRP h CREATE F6VSWRP”
Applicability:Phase 2 and Phase 3.
Visibility level: 2.
Command Description:This command adds the F6VSWRP object to the BTSE data base.
Long Names:NAME Address of the managed object
CELLNO cellNumber
VSWRTDB vswrThresholdDb
System Responses:Operation Completed
After command execution, a message of Changed Configuration Notification is dis-played. A further message indicates the result of the operation. An example of create command is the following:
JOB: 36
PC Time&Date: 25.09.2008 14:47:06 +02:00
NE Time&Date: 02.01.1990 00:03:47 +00:00
USER NAME: NSN
COMMAND: Create
F6VSWRP:NAME=RACK:0/F6VSWRP:0,CELLNO=0,VSWRTDB=LOW_2_5_HIGH_3_5;
SW RELEASE: 03-04-19-01-11-05_08-09-24
COMMAND RESULT:Operation successful.
cellnumber = 0
vswrThresholdDb = LOW_2_5_HIGH_3_5
END OF OUTPUT FOR JOB 36
Operation Failed
CREATE F6VSWRP NAME=RACK:0..7/F6VSWRP:0..1 ,CELLNO= [,VSWRTDB=];
DN0933412 Issue 01399
BTSplus mainline commands at the Flexi BSC product family
F6VSWRP
Id:0900d805805b102b
The specified Object has not been created. In addition to the general NACK causes, a specific NACK cause, which indicates that the command is inconsistent with the physical configuration, is possible. An example is the following:
JOB: 85
PC Time&Date: 16.09.2008 15:48:10 +02:00
NE Time&Date: 01.01.1990 00:08:52 +00:00
USER NAME: NSN
COMMAND: Create F6VSWRP:NAME=RACK:0/F6VSWRP:0,CELLNO=1;
SW RELEASE: 01-04-19-01-12-MB_08-09-16
COMMAND RESULT:Operation failed
cellNumber = 1
Message cannot be performed (-17)
END OF OUTPUT FOR JOB 85
Application Guidelines:
• The creation is mandatory if the module is equipped • The creation is rejected if any other combiner instance (DUAMCO,
DUVSWR,DULNA, DUDCTMA, FVSWRP, FTNFP, BCOM) is already created for the relatedACOM slots
• The creation of any other combiner object has to be rejected if a FICOM6 object iscreated for the slot(s)
Example of Command Execution:Create F6VSWRP:NAME=RACK:0/F6VSWRP:0,CELLNO=0,VSWRTDB=LOW_2_5_HIGH_3_5;e.
DELETE F6VSWRP
Command Tree:“MANAGED-ELEMENT h BSS-EQUIPMENT h BTSEP h RACK h F6VSWRP h DELETE F6VSWRP”
Applicability:Phase 2 and Phase 3.
Visibility level: 2.
Command Description:This command deletes the F6VSWRP object from the BTSE data base.
Long Names:NAME Address of the managed object
System Responses:Operation Completed
DELETE F6VSWRP NAME=RACK:0..7/F6VSWRP:0..1;
400DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805b102b
F6VSWRP
After command execution, a message of Changed Configuration Notification is dis-played. A further message indicates the result of the operation. An example of create command is the following:
JOB: 25
PC Time&Date: 25.09.2008 14:46:50 +02:00
NE Time&Date: 02.01.1990 00:03:31 +00:00
USER NAME: NSN
COMMAND: Delete F6VSWRP:NAME=RACK:0/F6VSWRP:0;
SW RELEASE: 03-04-19-01-11-05_08-09-24
COMMAND RESULT:Operation successful
END OF OUTPUT FOR JOB 25
Operation Failed
The specified Object has not been created. In addition to the general NACK causes, a specific NACK cause, which indicates that the command is inconsistent with the physical configuration, is possible.
Application Guidelines:None.
Example of Command Execution:Delete F6VSWRP:NAME=RACK:0/F6TNFP:0;
GET F6VSWRP
Command Tree:“MANAGED-ELEMENT h BSS-EQUIPMENT h BTSEP h RACK h F6VSWRP h GET F6VSWRP”
Applicability:Phase 2 and Phase 3.
Visibility level: 0.
Command Description:This command displays the attributes of F6VSWRP object.
Long Names:NAME Address of the managed object
REQATTL Required attribute list
ALS alarmStatus
AST administrativeState
AVS availabilityStatus
CELLNO cellNumber
GET F6VSWRP NAME=RACK:0..7/F6VSWRP:0..1 [,REQATTL=ALS, AST, AVS, CELLNO, OST, PRS, RELFUNCOBJ, VSWRTDB, F6FWID];
DN0933412 Issue 01401
BTSplus mainline commands at the Flexi BSC product family
F6VSWRP
Id:0900d805805b102b
OST operationalState
PRS proceduralStatus
RELFUNCOBJ relatedFuncObjects
VSWRTDB vswrThresholdDb
F6FWID ficom6FwId
System Responses:Operation Completed
A message indicates the result of the operation. An example of get command is the fol-lowing:
JOB: 148
PC Time&Date: 16.09.2008 16:06:01 +02:00
NE Time&Date: 01.01.1990 00:26:43 +00:00
USER NAME: NSN
COMMAND: Get F6VSWRP:NAME=RACK:0/F6VSWRP:0;
SW RELEASE: 01-04-19-01-12-MB_08-09-16
COMMAND RESULT:Operation successful
alarmStatus = CLEARED
administrativeState = Unlocked
availabilityStatus = NotInstalled
cellNumber = 1
operationalState = DISABLED
proceduralStatus = NULL
relatedFuncObjects = Null
vswrThresholdDb = LOW_2_0_HIGH_3_0
ficom6FwId = "BFFCiihh.SWI:00-hh-19-ii-ss-00_08-01-01"
END OF OUTPUT FOR JOB 148.
Operation Failed
None.
Application Guidelines:None.
Example of Command Execution:Get F6VSWRP:NAME=F6VSWRP:0, REQATTL=ALS& AST& AVS& CELLNO& OST&PRS& RELFUNCOBJ& VSWRTDB& F6FWID;
GETTEST F6VSWRPGETTEST F6VSWRP NAME=RACK:0..7/F6VSWRP:0..1;
402DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805b102b
F6VSWRP
Command Tree:“MANAGED-ELEMENT h BSS-EQUIPMENT h BTSEP h RACK h F6VSWRP h GETTEST F6VSWRP”
Applicability:Phase 2 and Phase 3.
Visibility level: 0.
Command Description:This command displays the attributes of the object test.
Long Names:NAME Address of the managed object
REQATTL Required attribute list
System Responses:Operation Completed
A message indicates the result of the operation. An example of gettest command is the following:
JOB: 296
PC Time&Date: 17.09.2008 16:12:51 +02:00
NE Time&Date: 17.09.2008 13:21:24 +01:00
USER NAME: NSN
COMMAND: Gettest F6VSWRP:NAME=RACK:0/F6VSWRP:1;
SW RELEASE: 01-04-19-01-12-MB_08-09-12
COMMAND RESULT:Operation successful
END OF OUTPUT FOR JOB 296.
Operation Failed
None.
Application Guidelines:None.
Example of Command Execution:Gettest F6VSWRP:NAME=RACK:0/F6TNFP:0;
LOCK F6VSWRP
Command Tree:“MANAGED-ELEMENT h BSS-EQUIPMENT h BTSEP h RACK h F6VSWRP h LOCK F6VSWRP”
Applicability:Phase 2 and Phase 3.
LOCK F6VSWRP NAME=RACK:0..7/F6VSWRP:0..1;
DN0933412 Issue 01403
BTSplus mainline commands at the Flexi BSC product family
F6VSWRP
Id:0900d805805b102b
Visibility level: 1.
Command Description:This command changes the administrative state of F6TNFP.
Long Names:NAME Address of the managed object
System Responses:Operation Completed
The specified change of administrative state has been perfomed:
JOB: 228
PC Time&Date: 17.09.2008 16:03:11 +02:00
NE Time&Date: 17.09.2008 13:11:44 +01:00
USER NAME: NSN
COMMAND: Lock F6VSWRP:NAME=RACK:0/F6VSWRP:0;
SW RELEASE: 01-04-19-01-12-MB_08-09-12
COMMAND RESULT:Operation successful
administrativeState = Locked
END OF OUTPUT FOR JOB 228.
Operation Failed
None.
Application Guidelines:None.
Example of Command Execution:Lock F6VSWRP:NAME=RACK:0/F6TNFP:0;
PERFTEST F6VSWRP
Command Tree:“MANAGED-ELEMENT h BSS-EQUIPMENT h BTSEP h RACK h F6VSWRP h PERFTEST F6VSWRP”
Applicability:Phase 2 and Phase 3.
Visibility level: 1.
Command Description:This command is used to start an asynchronous test in the object.
Long Names:NAME Address of the managed object
PERFTEST F6VSWRP NAME=RACK:0..7/F6VSWRP:0..1;
404DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805b102b
F6VSWRP
System Responses:Operation Completed
After command execution, a message of Changed Configuration Notification is dis-played. A further message indicates the result of the operation. An example of perftest command is the following:
JOB: 35
PC Time&Date: 26.09.2008 13:06:37 +02:00
NE Time&Date: 26.09.2008 10:13:55 +01:00
USER NAME: NSN
COMMAND: Perftest F6VSWRP:NAME=RACK:0/F6VSWRP:0;
SW RELEASE: 03-04-19-01-11-05_08-09-24
COMMAND RESULT:Operation successful
MOT = RACK:0/F6VSWRP:0
tO = BTSETEST:9
END OF OUTPUT FOR JOB 35
Operation Failed
The specified test cannot be performed. In addition to the general NACK causes, a specific NACK cause, which indicates that the command is inconsistent with the physical configuration, is possible.
Operation Failed
None.
Application Guidelines:None.
Example of Command Execution:Perftest F6VSWRP:NAME=RACK:0/F6DCTMA:0;
SET F6VSWRP
Command Tree:“MANAGED-ELEMENT h BSS-EQUIPMENT h BTSEP h RACK h F6VSWRP h SET F6VSWRP”
Applicability:Phase 2 and Phase 3.
Visibility level: 2.
Command Description:This command sets general attributes of F6VSWRP object.
Long Names:NAME Address of the managed object
SET F6VSWRP NAME=RACK:0..7/F6VSWRP:0..1 [,VSWRTDB=];
DN0933412 Issue 01405
BTSplus mainline commands at the Flexi BSC product family
F6VSWRP
Id:0900d805805b102b
VSWRTDB vswrThresholdDb
System Responses:Operation Completed
After command execution, a message of Changed Attribute Event Report is displayed. A further message indicates the result of the operation. An example of set command is the following:
JOB: 53
PC Time&Date: 24.09.2008 14:13:35 +02:00
NE Time&Date: 24.09.2008 10:22:09 +00:00
USER NAME: NSN
COMMAND: Set
F6VSWRP:NAME=RACK:0/F6VSWRP:0,VSWRTDB=LOW_3_0_HIGH_4_0;
SW RELEASE: 03-04-19-01-11-05_08-09-24
COMMAND RESULT:Operation successful
vswrThresholdDb = LOW_3_0_HIGH_4_0
END OF OUTPUT FOR JOB 53.
Operation Failed
None.
Application Guidelines:None.
Example of Command Execution:Set F6VSWRP:NAME=RACK:0/F6VSWRP:0,VSWRTDB=LOW_3_0_HIGH_4_0;
STOPTEST F6VSWRP
Command Tree:“MANAGED-ELEMENT h BSS-EQUIPMENT h BTSEP h RACK h F6VSWRP h STOPTEST F6VSWRP”
Applicability:Phase 2 and Phase 3.
Visibility level: 1.
Command Description:This command is used to stop a diagnostic previously started.
Long Names:NAME Address of the managed object
System Responses:Operation Completed
STOPTEST F6VSWRP NAME=RACK:0..7/F6VSWRP:0..1;
406DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805b102b
F6VSWRP
The test has been stopped. The System Responses will not be addressed to the MOT but to the object.
Operation Failed
The specified action has not been performed. In addition to the general NACK causes, a specific NACK cause, which indicates that the command is inconsistent with the physical configuration, is possible. An example is the following:
JOB: 244
PC Time&Date: 17.09.2008 16:07:01 +02:00
NE Time&Date: 17.09.2008 13:15:34 +01:00
USER NAME: NSN
COMMAND: Stoptest F6VSWRP:NAME=RACK:0/F6VSWRP:1;
SW RELEASE: 01-04-19-01-12-MB_08-09-12
COMMAND RESULT:Operation failed
MOT = RACK:0/F6VSWRP:1
Object instance unknown or not allowed (-9)
END OF OUTPUT FOR JOB 244.
Application Guidelines:None.
Example of Command Execution:Stoptest F6VSWRP:NAME=RACK:0/F6DCTMA:0;
UNLOCK F6VSWRP
Command Tree:“MANAGED-ELEMENT h BSS-EQUIPMENT h BTSEP h RACK h F6VSWRP h UNLOCK F6VSWRP”
Applicability:Phase 2 and Phase 3.
Visibility level: 1.
Command Description:This command changes the administrative state of F6LNA object.
Long Names:NAME Address of the managed object
System Responses:Operation Completed
The specified change of administrative state has been perfomed:
JOB: 227
PC Time&Date: 17.09.2008 16:03:02 +02:00
UNLOCK F6VSWRP NAME=RACK:0..7/F6VSWRP:0..1;
DN0933412 Issue 01407
BTSplus mainline commands at the Flexi BSC product family
F6VSWRP
Id:0900d805805b102b
NE Time&Date: 17.09.2008 13:11:35 +01:00
USER NAME: NSN
COMMAND: Unlock F6VSWRP:NAME=RACK:0/F6VSWRP:0;
SW RELEASE: 01-04-19-01-12-MB_08-09-12
COMMAND RESULT:Operation successful
administrativeState = Unlocked
END OF OUTPUT FOR JOB 227
Operation Failed
None.
Application Guidelines:None.
Example of Command Execution:Unlock F6VSWRP:NAME=RACK:0/F6DCTMA:0;
408DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805b102d
FANP
FANPThe self controlled central FAN units are used to guarantee a sufficient airflow for con-vection cooling of the modules. Two fans are responsible for each sub-rack. An inte-grated temperature sensor enables the fan control.
CREATE FANP
Command Tree:“MANAGED-ELEMENT h BSS-EQUIPMENT h BTSEP h RACK h FANP h CREATE FANP”
Applicability:Phase 2 and Phase 3.
Visibility level: 2.
Command Description:This command adds the FANP unit to the BTSE data base.
Long Names:NAME Address of the managed object
System Responses:Operation Completed
After command execution, a message of Changed Configuration Notification is dis-played. A further message indicates the result of the operation. An example of create command is the following:
JOB: 147
PC Time&Date: 12:01:41 03/23/2005
NE Time&Date: 13:03:16 09/15/2004
USER NAME: NSN
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: Operation successful
ChangedConfigurationNotification:
name = RACK:0/FANP:0
ChangeInfo = created
END OF OUTPUT FOR JOB 147
CREATE FANP NAME=RACK:0..7/FANP:0..7;
DN0933412 Issue 01409
BTSplus mainline commands at the Flexi BSC product family
FANP
Id:0900d805805b102d
JOB: 148
PC Time&Date: 12:01:41 03/23/2005
NE Time&Date: 13:03:16 09/15/2004
USER NAME: NSN
COMMAND: Create FANP:NAME=RACK:0/FANP:0;
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: Operation successful
END OF OUTPUT FOR JOB 148
Operation Failed
The specified Object has not been created. In addition to the general NACK causes, a specific NACK cause, which indicates that the command is inconsistent with the physical configuration, is possible. An example is the following:
JOB: 149
PC Time&Date: 12:02:04 03/23/2005
NE Time&Date: 13:03:39 09/15/2004
USER NAME: NSN
COMMAND: Create FANP:NAME=RACK:0/FANP:0;
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: OPERATION FAILED
Message cannot be performed (-17)
END OF OUTPUT FOR JOB 149
Application Guidelines:
• In operation, all FANPs must be created
• The maximum number of FANPs is: 6 for BS240/241/240SR/241SR and BS40/41, 8 for BS240XL/BS240XLSR, 5 for BS40II and 1 for BS82II
• The FANP object is always created with status unlocked.enable.null.null.cleared. If the HW is not connected or not present or if the board has a HW failure the object is then immediatly set to unlocked.disabled.failed
• If the operator creates in advance the object FANP in an extension rack which is not yet connected to the Base rack or if the ACT is not enabled, the FANP always keep
410DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805b102d
FANP
the states unlocked.enabled.null.null.cleared and no alarm is visible, even if the FAN-HW is not present or the board has an HW-failure
• In the BS82 II the ACT must also be enabled in the base rack for correct displaying of the FAN status
Example of Command Execution:Create FANP:NAME=RACK:0/FANP:0;
DELETE FANP
Command Tree:“MANAGED-ELEMENT h BSS-EQUIPMENT h BTSEP h RACK h FANP h DELETE FANP”
Applicability:Phase 2 and Phase 3.
Visibility level: 2.
Command Description:This command deletes the FANP unit from the BTSE data base.
Long Names:NAME Address of the managed object
System Responses:Operation Completed
After command execution, a message of Changed Configuration Notification is dis-played. A further message indicates the result of the operation. An example of delete command is the following:
JOB: 145
PC Time&Date: 12:01:38 03/23/2005
NE Time&Date: 13:03:13 09/15/2004
USER NAME: NSN
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: Operation successful
ChangedConfigurationNotification:
name = RACK:0/FANP:0
ChangeInfo = deleted
DELETE FANP NAME=RACK:0..7/FANP:0..7;
DN0933412 Issue 01411
BTSplus mainline commands at the Flexi BSC product family
FANP
Id:0900d805805b102d
END OF OUTPUT FOR JOB 145
JOB: 146
PC Time&Date: 12:01:38 03/23/2005
NE Time&Date: 13:03:13 09/15/2004
USER NAME: NSN
COMMAND: Delete FANP:NAME=RACK:0/FANP:0;
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: Operation successful
END OF OUTPUT FOR JOB 146
Operation Failed
The specified Object has not been deleted. Additionally to the general NACK causes, a specific NACK cause, meaning that the command is inconsistent with physical configu-ration, is possible.
Application Guidelines:
• FANP must be locked in Phase 3, before deletion
• The deletion of a FANP is critical in operation
Example of Command Execution:Delete FANP:NAME=RACK:0/FANP:0;
GET FANP
Command Tree:“MANAGED-ELEMENT h BSS-EQUIPMENT h BTSEP h RACK h FANP h GET FANP”
Applicability:Phase 2 and Phase 3.
Visibility level: 0.
Command Description:This command displays the attributes of the FANP units of the BTSE.
Long Names:NAME Address of the managed object
REQATTL Required attribute list
GET FANP NAME=RACK:0..7/FANP:0..7 [,REQATTL=ALS, AST, AVS, OST, PRS, RELFUNCOBJ];
412DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805b102d
FANP
ALS alarmStatus
AST administrativeState
AVS availabilityStatus
OST operationalState
PRS proceduralStatus
RELFUNCOBJ relatedFuncObjects
System Responses:Operation Completed
After command execution, a message of Changed Configuration Notification is dis-played. A further message indicates the result of the operation. An example of get command is the following:
JOB: 132
PC Time&Date: 12:01:18 03/23/2005
NE Time&Date: 13:02:53 09/15/2004
USER NAME: NSN
COMMAND: Get FANP:NAME=RACK:0/FANP:0;
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: Operation successful
alarmStatus = CLEARED
administrativeState = Unlocked
availabilityStatus = NULL
operationalState = ENABLED
proceduralStatus = NULL
relatedFuncObjects =
END OF OUTPUT FOR JOB 132
Operation Failed
The GET command has not been successfully executed. A general NACK will indicate possible errors or a specific NACK strictly related to the single command is possible.
Application Guidelines:
• The value for ProcStatus must be Null Status
• The relatedFuncObjects always empty
Example of Command Execution:Get FANP:NAME=RACK:0/FANP:0,REQATTL=ALS&AST&AVS&OST&PRS;
DN0933412 Issue 01413
BTSplus mainline commands at the Flexi BSC product family
FANP
Id:0900d805805b102d
GETTEST FANP
Command Tree:“MANAGED-ELEMENT h BSS-EQUIPMENT h BTSEP h RACK h FANP h GETTEST FANP”
Applicability:Phase 2 and Phase 3.
Visibility level: 0.
Command Description:This command displays the attributes of the FANP test.
Long Names:NAME Address of the managed object
REQATTL Required attribute list
System Responses:Operation Completed
After command execution, a message of Changed Configuration Notification is dis-played. A further message indicates the result of the operation. An example of gettest command is the following:
JOB: 140
PC Time&Date: 12:01:25 03/23/2005
NE Time&Date: 13:03:00 09/15/2004
USER NAME: NSN
COMMAND: Gettest FANP:NAME=RACK:0/FANP:0;
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: Operation successful
MOT = RACK:0/FANP:0
testMonitor =
phaseId = PreliminaryTestsFanp
phaseStatus = Running
phaseId = CheckAlarmStatusFanp
phaseStatus = Waiting
phaseId = EndTestFanp
phaseStatus = Waiting
testOutcome = INCONCLUSIVE
GETTEST FANP NAME=RACK:0..7/FANP:0..7;
414DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805b102d
FANP
testState = INITIALIZING
END OF OUTPUT FOR JOB 140
Operation Failed
The GET command has not been successfully executed. A general NACK will indicate possible errors or a specific NACK strictly related to the single command is possible.
Application Guidelines:None.
Example of Command Execution:Gettest FANP:NAME=RACK:0/FANP:0;
LOCK FANP
Command Tree:“MANAGED-ELEMENT h BSS-EQUIPMENT h BTSEP h RACK h FANP h LOCK FANP”
Applicability:Phase 2 and Phase 3.
Visibility level: 1.
Command Description:This command changes the administrative state of the FANP unit of the BTSE.
Long Names:NAME Address of the managed object
testMonitor it is a list of all test phases related to the selected object; for each phase the related phaseStatus is provided (Passed, Failed, Running or Waiting).
phaseId =
phaseStatus =
phaseId =
phaseStatus =
...
...
testOutcome It represents the test result: it can be Inconclusive (if the phases already executed were successful) or Fail (if at least one of the executed phases failed).
testState = Testing It can assume one of the following values: not_initialized, idle, initializing, sus-pended, testing, terminating and dis-abled.
LOCK FANP NAME=RACK:0..7/FANP:0..7;
DN0933412 Issue 01415
BTSplus mainline commands at the Flexi BSC product family
FANP
Id:0900d805805b102d
System Responses:Operation Completed
The specified change of administrative state has been perfomed:
JOB: 143
PC Time&Date: 12:01:36 03/23/2005
NE Time&Date: 13:03:11 09/15/2004
USER NAME: NSN
COMMAND: Lock FANP:NAME=RACK:0/FANP:0;
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: Operation successful
administrativeState = Locked
END OF OUTPUT FOR JOB 143
CHANGED STATE EVENT REPORT:
This provides information about the administrative state, the operational state and the availability status every time a state change occurs:
JOB: 144
PC Time&Date: 12:01:36 03/23/2005
NE Time&Date: 13:03:11 09/15/2004
USER NAME: NSN
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: Operation successful
CHANGED STATE EVENT REPORT:
NAME = RACK:0/FANP:0
Administrative State = LOCKED
Notification Identifier = 341
END OF OUTPUT FOR JOB 144
Operation Failed
The specified change of administrative state has not been performed.
416DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805b102d
FANP
Application Guidelines:
• After locking of the FANP, the FANP will still be in operation, but in the administrative state Locked.
Example of Command Execution:Lock FANP:NAME=RACK:0/FANP:0;
PERFTEST FANP
Command Tree:“MANAGED-ELEMENT h BSS-EQUIPMENT h BTSEP h RACK h FANP h PERFTEST FANP”
Applicability:Phase 2 and Phase 3.
Visibility level: 1.
Command Description:This command is used to start an asynchronous test in FANP.
Long Names:NAME Address of the managed object
System Responses:Operation Completed
Test configuration has been set and the specified test has been started. The System response will not be addressed to the MOT but to the object BTSEP.
JOB: 136
PC Time&Date: 12:01:25 03/23/2005
NE Time&Date: 13:03:00 09/15/2004
USER NAME: NSN
COMMAND: Perftest FANP:NAME=RACK:0/FANP:0;
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: Operation successful
MOT = RACK:0/FANP:0
tO = BTSETEST:6
END OF OUTPUT FOR JOB 136
PERFTEST FANP NAME=RACK:0..7/FANP:0..7;
DN0933412 Issue 01417
BTSplus mainline commands at the Flexi BSC product family
FANP
Id:0900d805805b102d
JOB: 137
PC Time&Date: 12:01:25 03/23/2005
NE Time&Date: 13:03:00 09/15/2004
USER NAME: NSN
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: Operation successful
ChangedConfigurationNotification:
name = BTSETEST:6
ChangeInfo = created
END OF OUTPUT FOR JOB 137
JOB: 138
PC Time&Date: 12:01:25 03/23/2005
NE Time&Date: 13:03:00 09/15/2004
USER NAME: NSN
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: Operation successful
CHANGED STATE EVENT REPORT:
NAME = RACK:0/FANP:0
Operational State = ENABLED
Availability Status = NULL_value
Notification Identifier = 339
END OF OUTPUT FOR JOB 138
JOB: 139
PC Time&Date: 12:01:25 03/23/2005
418DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805b102d
FANP
NE Time&Date: 13:03:00 09/15/2004
USER NAME: NSN
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: Operation successful
Test Report:
name = BTSETEST:6
testOutcome = PASSED
testTermination = Normal
MOT = RACK:0/FANP:0
executedPhases =
PreliminaryTestsFanp
CheckAlarmStatusFanp
EndTestFanp
END OF OUTPUT FOR JOB 139
JOB: 140
PC Time&Date: 12:01:25 03/23/2005
NE Time&Date: 13:03:00 09/15/2004
USER NAME: NSN
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: Operation successful
ChangedConfigurationNotification:
name = BTSETEST:6
ChangeInfo = deleted
END OF OUTPUT FOR JOB 140
The test results will be displayed at the end of the test phases.
Result TEST:
name = TEST:<n>
DN0933412 Issue 01419
BTSplus mainline commands at the Flexi BSC product family
FANP
Id:0900d805805b102d
Operation Failed
This NACK-message occurs in the following cases: Message cannot be performed, test not supported, capacity restrictions, physical configuration cannot be performed, object not locked.
Application Guidelines:
• In phase 3 MO must be locked previous to the command execution
Example of Command Execution:Perftest FANP:NAME=RACK:0/FANP:0;
testOutcome = This field represents the test result; one of the fol-lowing values can be displayed:
Pass all the test phases are successfully performed.
Inconclusive the test is aborted by the system or the test is terminated by the opera-tor.
Fail if at least one of the executed phases fail.
mOts = It is the identifier of the hardware object under test.
testTermination = It specifies how the test is terminated, it can assume the following values:
Normal all the test phases are performed.
Abort the test is aborted by system.
Cancel the test is terminated by operator.
executedPhases
phaseId = It represents the list of the executed test phases (in case of successful test result, all the test phases will be listed).
additionalWords =
....
failedPhases
phaseId = It represents the list of the failed test phase; addi-tional information is provided for each phase.phaseId =
....
skippedPhases
phaseId = It represents the list of the skipped phases; they are displayed only for test stopped during it execution.phaseId =
....
poprosedRepair Action =
A list of most probable fail probable causes is shown (max four messages)
420DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805b102d
FANP
STOPTEST FANP
Command Tree:“MANAGED-ELEMENT h BSS-EQUIPMENT h BTSEP h RACK h FANP h STOPTEST FANP”
Applicability:Phase 2 and Phase 3.
Visibility level: 1.
Command Description:This command is used to stop a diagnostic previously started.
Long Names:NAME Address of the managed object
System Responses:Operation Completed
Test has been stopped. The System Responses will not be addressed to the MOT but to the object BTSEP.
Operation Failed
Test has not been stopped. This NACK-message can occur when the specified test is not running or in case of test which cannot be stopped.
STOPTEST FANP NAME=RACK:0..7/FANP:0..7;
Result TEST:
name = TEST:<n>
testOutcome = inconclusive
mOts = It is the identifier of the hardware object under test.
testTermination = Cancel
executedPhases
phaseId = It represents the list of the executed test phases; the list is not shown for test in the waiting list (queued)....
.
failedPhases
phaseId = It represents the list of the failed test phase;
additional information is provided for each phase.phaseId =
....
skippedPhases
phaseId = It represents the list of the skipped phases;the list is not shown for test in the waiting list (queued).phaseId =
DN0933412 Issue 01421
BTSplus mainline commands at the Flexi BSC product family
FANP
Id:0900d805805b102d
Application Guidelines:None.
Example of Command Execution:Stoptest FANP:NAME=RACK:0/FANP:0;
UNLOCK FANP
Command Tree:“MANAGED-ELEMENT h BSS-EQUIPMENT h BTSEP h RACK h FANP h UNLOCK FANP”
Applicability:Phase 2 and Phase 3.
Visibility level: 1.
Command Description:This command changes the administrative state of the FANP unit of the BTSE.
Long Names:NAME Address of the managed object
System Responses:Operation Completed
The specified change of administrative state has been perfomed:
JOB: 141
PC Time&Date: 12:01:28 03/23/2005
NE Time&Date: 13:03:03 09/15/2004
USER NAME: NSN
COMMAND: Unlock FANP:NAME=RACK:0/FANP:0;
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: Operation successful
administrativeState = Unlocked
END OF OUTPUT FOR JOB 141
CHANGED STATE EVENT REPORT:
UNLOCK FANP NAME=RACK:0..7/FANP:0..7;
422DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805b102d
FANP
This provides information about the administrative state, the operational state and the availability status every time a state change occurs:
JOB: 142
PC Time&Date: 12:01:28 03/23/2005
NE Time&Date: 13:03:03 09/15/2004
USER NAME: NSN
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: Operation successful
CHANGED STATE EVENT REPORT:
NAME = RACK:0/FANP:0
Administrative State = UNLOCKED
Notification Identifier = 340
END OF OUTPUT FOR JOB 142
Operation Failed
The specified change of administrative state has not been performed.
Application Guidelines:
• After locking of the FANP, the FANP will still be in operation, but in the administrative state Locked
Example of Command Execution:Unlock FANP:NAME=RACK:0/FANP:0;
DN0933412 Issue 01423
BTSplus mainline commands at the Flexi BSC product family
FCUMAIN
Id:0900d805805b102f
FCUMAINThe FlexCU board is modeled with three HMO instances: 1 instance of the FCUMAIN HMO and 2 instances of the FCUTR HMO. The FCUMAIN instance represents that part of the board which performs board related activities and the FCUTR instances represent carrier (TRX) specific activities. There is a dependency of the FCUTR instances towards the FCUMAIN instance of a FlexCU.
CREATE FCUMAIN
Command Tree:“MANAGED-ELEMENT h BSS-EQUIPMENT h BTSEP h RACK h FCUMAIN h CREATE FCUMAIN”
Applicability:Phase 2 and Phase 3.
Visibility level: 2.
Command Description:This command adds the FCUMAIN unit to the BTSE data base.
Long Names:NAME Address of the managed object
FCUMODE fcuMode
RXLEVADJ rxLevAdjust(dB)
RXLEVADJN1D1 rxLevAdjustN1D1(dB)
TCC txCoherentComb
System Responses:Operation Completed
After command execution, a message of Changed Configuration Notification is dis-played. A further message indicates the result of the operation. An example of create command is the following:
JOB: 56
PC Time&Date: 16:34:31 03/23/2005
NE Time&Date: 16:32:25 09/15/2004
USER NAME: NSN
COMMAND: Create FCUMAIN:NAME=RACK:0/FCUMAIN:0,FCUMODE=single-CUMode,RXLEVADJ=1-1,RXLEVADJN1D1=1-1;
SW RELEASE: 01-04-17-01-26-51_05-02-23
CREATE FCUMAIN NAME=RACK:0..7/FCUMAIN:0..11 [,FCUMODE=] [,RXLE-VADJ=] [,RXLEVADJN1D1=] [,TCC=];
424DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805b102f
FCUMAIN
COMMAND RESULT: Operation successful
ChangedConfigurationNotification:
name = RACK:0/FCUMAIN:0
ChangeInfo = created
M
END OF OUTPUT FOR JOB 56
JOB: 57
PC Time&Date: 16:34:31 03/23/2005
NE Time&Date: 16:32:25 09/15/2004
USER NAME: NSN
COMMAND: Create FCUMAIN:NAME=RACK:0/FCUMAIN:0,FCUMODE=singleCU-Mode,RXLEVADJ=1-1,RXLEVADJN1D1=1-1;
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: Operation successful
fcuMode = singleCUMode
rxLevAdjust(dB) =
adjustValue = 1.0
adjustDivValue = 1.0
rxLevAdjustN1D1(dB) =
adjustValueN1 = 1.0
adjustDivValueD1 = 1.0
END OF OUTPUT FOR JOB 57
Operation Failed
The specified Object has not been created. In addition to the general NACK causes, a specific NACK cause, which indicates that the command is inconsistent with the physical configuration, is possible. An example is the following:
JOB: 76
PC Time&Date: 16:37:54 03/23/2005
NE Time&Date: 16:35:47 09/15/2004
DN0933412 Issue 01425
BTSplus mainline commands at the Flexi BSC product family
FCUMAIN
Id:0900d805805b102f
USER NAME: NSN
COMMAND: Create FCUMAIN:NAME=RACK:0/FCUMAIN:0,FCUMODE=single-CUMode,RXLEVADJ=1-1,RXLEVADJN1D1=1-1;
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: Operation failed
fcuMode = singleCUMode
rxLevAdjust(dB) =
adjustValue = 1.0
adjustDivValue = 1.0
rxLevAdjustN1D1(dB) =
adjustValueN1 = 1.0
adjustDivValueD1 = 1.0
Message cannot be performed (-17)
END OF OUTPUT FOR JOB 76
Application Guidelines:None.
Example of Command Execution:Create FCUMAIN: NAME=RACK:0/FCUMAIN:0,FCUMODE=singleCUMode,
RXLEVADJ-20,RXLEVADJN1D1-20;
DELETE FCUMAIN
Command Tree:“MANAGED-ELEMENT h BSS-EQUIPMENT h BTSEP h RACK h FCUMAIN h DELETE FCUMAIN”
Applicability:Phase 2 and Phase 3.
Visibility level: 2.
Command Description:This command deletes the FCUMAIN unit from the BTSE data base.
Long Names:NAME Address of the managed object
System Responses:Operation Completed
DELETE FCUMAIN NAME=RACK:0..7/FCUMAIN:0..11;
426DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805b102f
FCUMAIN
After command execution, a message of Changed Configuration Notification is dis-played. A further message indicates the result of the operation. An example of delete command is the following:
JOB: 66
PC Time&Date: 16:35:23 03/23/2005
NE Time&Date: 16:33:17 09/15/2004
USER NAME: NSN
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: Operation successful
ChangedConfigurationNotification:
name = RACK:0/FCUMAIN:0
ChangeInfo = deleted
END OF OUTPUT FOR JOB 66
JOB: 67
PC Time&Date: 16:35:23 03/23/2005
NE Time&Date: 16:33:17 09/15/2004
USER NAME: NSN
COMMAND: Delete FCUMAIN:NAME=RACK:0/FCUMAIN:0;
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: Operation successful
END OF OUTPUT FOR JOB 67
Operation Failed
The specified Object has not been deleted. Additionally to the general NACK causes, a specific NACK cause, meaning that the command is inconsistent with physical configu-ration, is possible.
Application Guidelines:None.
Example of Command Execution:Delete FCUMAIN:NAME=RACK:0/FCUMAIN:0;
DN0933412 Issue 01427
BTSplus mainline commands at the Flexi BSC product family
FCUMAIN
Id:0900d805805b102f
GET FCUMAIN
Command Tree:“MANAGED-ELEMENT h BSS-EQUIPMENT h BTSEP h RACK h FCUMAIN h GET FCUMAIN”
Applicability:Phase 2 and Phase 3.
Visibility level: 0.
Command Description:This command displays the attributes of the FCUMAIN unit of the BTSE.
Long Names:NAME Address of the managed object
REQATTL Required attribute list
ALS alarmStatus
AST administrativeState
AVS availabilityStatus
BSWVER bootSoftwareVersion
FCUMODE fcuMode
OST operationalState
PRS proceduralStatus
RELFUNCOBJ relatedFuncObjects
RXLEVADJ rxLevAdjust(dB)
RXLEVADJN1D1 rxLevAdjustN1D1(dB)
FPGAFWVER fpgaFwVer
TCC txCoherentComb
System Responses:Operation Completed
After command execution, a message of Changed Configuration Notification is dis-played. A further message indicates the result of the operation. An example of get command is the following:
JOB: 59
PC Time&Date: 16:34:52 03/23/2005
NE Time&Date: 16:32:46 09/15/2004
USER NAME: NSN
GET FCUMAIN NAME=RACK:0..7/FCUMAIN:0..11 [,REQATTL=ALS, AST, AVS, BSWVER, FCUMODE, OST, PRS, RELFUNCOBJ, RXLEVADJ, RXLEVADJN1D1, FPGAFWVER, TCC];
428DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805b102f
FCUMAIN
COMMAND: Get FCUMAIN:NAME=RACK:0/FCUMAIN:0;
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: Operation successful
alarmStatus = CLEARED
administrativeState = Unlocked
availabilityStatus = NotInstalled
bootSoftwareVersion = ""
fcuMode = doubleCUMode
operationalState = DISABLED
proceduralStatus = NULL
relatedFuncObjects =
rxLevAdjust(dB) =
adjustValue = 0.0
adjustDivValue = 0.0
rxLevAdjustN1D1(dB) =
adjustValueN1 = 0.0
adjustDivValueD1 = 0.0
END OF OUTPUT FOR JOB 59
Operation Failed
The GET command has not been successfully executed. A general NACK will indicate possible errors or a specific NACK strictly related to the single command is possible.
Application Guidelines:None.
Example of Command Execution:Get FCUMANIN:NAME=RACK:0/FTNFP:0,REQATTL=ALS&AST&AVS&BSWVER&
FCUMODE&OST&PRS&RELFUNCOBJ& RXLEVADJ&RXLEVADJN1D1;
GET FCUMAIN FWID
Command Tree:“MANAGED-ELEMENT h BSS-EQUIPMENT h BTSEP h RACK h FCUMAIN h GET FCUMAIN FWID”
Applicability:Phase 2 and Phase 3.
Visibility level: 0.
GET FCUMAIN FWID NAME=RACK:0..7/FCUMAIN:0..11;
DN0933412 Issue 01429
BTSplus mainline commands at the Flexi BSC product family
FCUMAIN
Id:0900d805805b102f
Command Description:This command provides information on the FPGA FW images that are contained in the boards flash prom together with an indication of the “active” version. Up to 4 images are provided per board. For FlexCUv2 or ECUv6 boards the FPGA FW versions are provided together with an indication whether the FW version is the active one.
Long Names:NAME Address of the managed object
REQATTL Required attribute list
System Responses:Operation Completed
None.
Operation Failed
None.
Application Guidelines:None.
Example of Command Execution:Get FCUMAIN FWID:NAME=RACK:0/FCUMAIN:1, REQATTL=FPGAFWVER;
GET FCUMAIN WIRING
Command Tree:“MANAGED-ELEMENT h BSS-EQUIPMENT h BTSEP h RACK h FCUMAIN h GET FCUMAIN WIRING”
Applicability:Phase 2 and Phase 3.
Visibility level: 0.
Command Description:This command displays the attributes of the FCUMAIN unit of the BTSE.
Long Names:NAME Address of the managed object
REQATTL Required attribute list
System Responses:Operation Completed
After command execution, a message of Changed Configuration Notification is dis-played. A further message indicates the result of the operation. An example of get wiring command is the following:
JOB: 221
GET FCUMAIN WIRING NAME=RACK:0..7/FCUMAIN:0..11;
430DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805b102f
FCUMAIN
PC Time&Date: 12:13:58 03/23/2005
NE Time&Date: 13:15:33 09/15/2004
USER NAME: NSN
COMMAND: Get FCUMAIN WIRING:NAME=RACK:0/FCUMAIN:1;
SW RELEASE: 01-04-17-01-26-51_05-02-23COMMAND RESULT: Operation suc-cessful
fcumainWiring =
variable
END OF OUTPUT FOR JOB 221
Operation Failed
The GET command has not been successfully executed. A general NACK will indicate possible errors or a specific NACK strictly related to the single command is possible.
Application Guidelines:
• Refer to “FCUMAINWIRING”
Example of Command Execution:Get FCUMAIN WIRING:NAME=RACK:0/FCUMAIN:0;
GETTEST FCUMAIN
Command Tree:“MANAGED-ELEMENT h BSS-EQUIPMENT h BTSEP h RACK h FCUMAIN h GETTEST FCUMAIN”
Applicability:Phase 2 and Phase 3.
Visibility level: 0.
Command Description:This command displays the attributes of the FCUMAIN test.
Long Names:NAME Address of the managed object
REQATTL Required attribute list
System Responses:Operation Completed
GETTEST FCUMAIN NAME=RACK:0..7/FCUMAIN:0..11;
DN0933412 Issue 01431
BTSplus mainline commands at the Flexi BSC product family
FCUMAIN
Id:0900d805805b102f
After command execution, a message of Changed Configuration Notification is dis-played. A further message indicates the result of the operation. An example of gettest command is the following:
JOB: 221
PC Time&Date: 12:13:58 03/23/2005
NE Time&Date: 13:15:33 09/15/2004
USER NAME: NSN
COMMAND: Gettest FCUMAIN:NAME=RACK:0/FCUMAIN:0;
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: Operation successful
MOT = RACK:0/FCUMAIN:0
testMonitor =
phaseId = PreliminaryTestsFCUMAIN
phaseStatus = Running
phaseId = CheckAlarmStatusFCUMAIN
phaseStatus = Waiting
phaseId = EndTestFCUMAIN
phaseStatus = Waiting
testOutcome = INCONCLUSIVE
testState = INITIALIZING
END OF OUTPUT FOR JOB 221
Operation Failed
The GET command has not been successfully executed. A general NACK will indicate possible errors or a specific NACK strictly related to the single command is possible.
testMonitor it is a list of all test phases related to the selected object; for each phase the related phaseStatus is provided (Passed, Failed, Running or Waiting).
phaseId =
phaseStatus =
phaseId =
phaseStatus =
...
...
testOutcome It represents the test result: it can be Inconclusive (if the phases already executed were successful) or Fail (if at least one of the executed phases failed).
432DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805b102f
FCUMAIN
Application Guidelines:None.
Example of Command Execution:Gettest FCUMAIN:NAME=RACK:0/FCUMAIN:0;
LOCK FCUMAIN
Command Tree:“MANAGED-ELEMENT h BSS-EQUIPMENT h BTSEP h RACK h FCUMAIN h LOCK FCUMAIN”
Applicability:Phase 2 and Phase 3.
Visibility level: 1.
Command Description:This command changes the administrative state of the FCUMAIN object of the BTSE.
Long Names:NAME Address of the managed object
System Responses:Operation Completed
The specified change of administrative state has been perfomed:
JOB: 60
PC Time&Date: 16:35:08 03/23/2005
NE Time&Date: 16:33:02 09/15/2004
USER NAME: NSN
COMMAND: Lock FCUMAIN:NAME=RACK:0/FCUMAIN:0;
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: Operation successful
administrativeState = Locked
testState = Testing It can assume one of the following values: not_initialized, idle, initializing, sus-pended, testing, terminating and dis-abled.
LOCK FCUMAIN NAME=RACK:0..7/FCUMAIN:0..11;
DN0933412 Issue 01433
BTSplus mainline commands at the Flexi BSC product family
FCUMAIN
Id:0900d805805b102f
END OF OUTPUT FOR JOB 60
CHANGED STATE EVENT REPORT:
This provides information about the administrative state, the operational state and the availability status every time a state change occurs:
JOB: 61
PC Time&Date: 16:35:08 03/23/2005
NE Time&Date: 16:33:02 09/15/2004
USER NAME: NSN
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: Operation successful
CHANGED STATE EVENT REPORT:
NAME = RACK:0/FCUMAIN:0
Administrative State = LOCKED
Notification Identifier = 494
END OF OUTPUT FOR JOB 61
Operation Failed
The specified change of administrative state has not been performed.
Application Guidelines:None.
Example of Command Execution:Lock FCUMAIN:NAME=RACK:0/FCUMANIN:0
PERFTEST FCUMAIN
Command Tree:“MANAGED-ELEMENT h BSS-EQUIPMENT h BTSEP h RACK h FCUMAIN h PERFTEST FCUMAIN”
Applicability:Phase 2 and Phase 3.
Visibility level: 1.
PERFTEST FCUMAIN NAME=RACK:0..7/FCUMAIN:0..11;
434DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805b102f
FCUMAIN
Command Description:This command is used to start an asynchronous test in FCUMAIN .
Long Names:NAME Address of the managed object
System Responses:Operation Completed
Test configuration has been set and the specified test has been started. The System response will not be addressed to the MOT but to the object BTSEP.
JOB: 222
PC Time&Date: 12:14:01 03/23/2005
NE Time&Date: 13:15:36 09/15/2004
USER NAME: NSN
COMMAND: Perftest FCUMAIN:NAME=RACK:0/FCUMAIN:0;
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: Operation successful
MOT = RACK:0/FCUMAIN:0
tO = BTSETEST:6
END OF OUTPUT FOR JOB 222
JOB: 223
PC Time&Date: 12:14:01 03/23/2005
NE Time&Date: 13:15:36 09/15/2004
USER NAME: NSN
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: Operation successful
ChangedConfigurationNotification:
name = BTSETEST:6
ChangeInfo = created
DN0933412 Issue 01435
BTSplus mainline commands at the Flexi BSC product family
FCUMAIN
Id:0900d805805b102f
END OF OUTPUT FOR JOB 223
JOB: 224
PC Time&Date: 12:14:01 03/23/2005
NE Time&Date: 13:15:36 09/15/2004
USER NAME: NSN
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: Operation successful
CHANGED STATE EVENT REPORT:
NAME = RACK:0/FCUMAIN:0
Operational State = ENABLED
Availability Status = NULL_value
Notification Identifier = 139
END OF OUTPUT FOR JOB 224
JOB: 225
PC Time&Date: 12:14:01 03/23/2005
NE Time&Date: 13:15:36 09/15/2004
USER NAME: NSN
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: Operation successful
Test Report:
name = BTSETEST:6
testOutcome = PASSED
testTermination = Normal
MOT = RACK:0/FCUMAIN:0
executedPhases =
PreliminaryTestsFCUMAIN
CheckAlarmStatusFCUMAIN
436DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805b102f
FCUMAIN
EndTestFCUMAIN
END OF OUTPUT FOR JOB 225
JOB: 226
PC Time&Date: 12:14:01 03/23/2005
NE Time&Date: 13:15:36 09/15/2004
USER NAME: NSN
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: Operation successful
ChangedConfigurationNotification:
name = BTSETEST:6
ChangeInfo = deleted
END OF OUTPUT FOR JOB 226
The test results will be displayed at the end of the test phases.
Result TEST:
name = TEST:<n>
testOutcome = This field represents the test result; one of the fol-lowing values can be displayed:
Pass all the test phases are successfully performed.
Inconclusive the test is aborted by the system or the test is terminated by the opera-tor.
Fail if at least one of the executed phases fail.
mOts = It is the identifier of the hardware object under test.
testTermination = It specifies how the test is terminated, it can assume the following values:
Normal all the test phases are performed.
Abort the test is aborted by system.
Cancel the test is terminated by operator.
executedPhases
DN0933412 Issue 01437
BTSplus mainline commands at the Flexi BSC product family
FCUMAIN
Id:0900d805805b102f
Operation Failed
This NACK-message occurs in the following cases: Message cannot be performed, test not supported, capacity restrictions, physical configuration cannot be performed, object not locked.
Application Guidelines:None.
Example of Command Execution:Perftest FCUMAIN:NAME=RACK:0/FCUMANIN:0
SET FCUMAIN
Command Tree:“MANAGED-ELEMENT h BSS-EQUIPMENT h BTSEP h RACK h FCUMAIN h SET FCUMAIN”
Applicability:Phase 2 and Phase 3.
Visibility level: 2.
Command Description:This command is used to set the attributes of the specified FCUMAIN .
Long Names:NAME Address of the managed object
RXLEVADJ rxLevAdjust(dB)
RXLEVADJN1D1 rxLevAdjustN1D1(dB)
phaseId = It represents the list of the executed test phases (in case of successful test result, all the test phases will be listed).
additionalWords =
....
failedPhases
phaseId = It represents the list of the failed test phase; addi-tional information is provided for each phase.phaseId =
....
skippedPhases
phaseId = It represents the list of the skipped phases; they are displayed only for test stopped during it execution.phaseId =
....
poprosedRepair Action =
A list of most probable fail probable causes is shown (max four messages)
SET FCUMAIN NAME=RACK:0..7/FCUMAIN:0..11 [,RXLEVADJ=] [,RXLEVADJN1D1=] [,TCC=];
438DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805b102f
FCUMAIN
TCC txCoherentComb
System Responses:Operation Completed
After command execution, a message of Changed Attribute Event Report is displayed. A further message indicates the result of the operation. An example of set command is the following:
JOB: 176
PC Time&Date: 12:05:36 03/23/2005
NE Time&Date: 13:07:12 09/15/2004
USER NAME: NSN
COMMAND: Set FCUMAIN:NAME=RACK:0/FCUMAIN:0;
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: Operation successful
END OF OUTPUT FOR JOB 176
Operation Failed
The specified attributes have not been set. In addition to the general NACK causes, a specific NACK cause, which indicates that the command is inconsistent with the physical configuration, is possible.
Application Guidelines:None.
Example of Command Execution:Set FCUMAIN:NAME=RACK:0/FCUMANIN:0,RXLEVADJ=-2,RXLEVADJN1D1=-2
STOPTEST FCUMAIN
Command Tree:“MANAGED-ELEMENT h BSS-EQUIPMENT h BTSEP h RACK h FCUMAIN h STOPTEST FCUMAIN”
Applicability:Phase 2 and Phase 3.
Visibility level: 1.
Command Description:This command is used to stop a diagnostic previously started.
STOPTEST FCUMAIN NAME=RACK:0..7/FCUMAIN:0..11;
DN0933412 Issue 01439
BTSplus mainline commands at the Flexi BSC product family
FCUMAIN
Id:0900d805805b102f
Long Names:NAME Address of the managed object
System Responses:Operation Completed
Test has been stopped. The System Responses will not be addressed to the MOT but to the object BTSEP.
Operation Failed
Test has not been stopped. This NACK-message can occur when the specified test is not running or in case of test which cannot be stopped.
Application Guidelines:None.
Example of Command Execution:Stoptest FCUMAIN:NAME=RACK:0/FCUMANIN:0;
UNLOCK FCUMAIN
Command Tree:“MANAGED-ELEMENT h BSS-EQUIPMENT h BTSEP h RACK h FCUMAIN h UNLOCK FCUMAIN”
Result TEST:
name = TEST:<n>
testOutcome = inconclusive
mOts = It is the identifier of the hardware object under test.
testTermination = Cancel
executedPhases
phaseId = It represents the list of the executed test phases; the list is not shown for test in the waiting list (queued)....
.
failedPhases
phaseId = It represents the list of the failed test phase;
additional information is provided for each phase.phaseId =
....
skippedPhases
phaseId = It represents the list of the skipped phases;the list is not shown for test in the waiting list (queued).phaseId =
UNLOCK FCUMAIN NAME=RACK:0..7/FCUMAIN:0..11;
440DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805b102f
FCUMAIN
Applicability:Phase 2 and Phase 3.
Visibility level: 1.
Command Description:This command changes the administrative state of the FCUMAIN object of the BTSE.
Long Names:NAME Address of the managed object
System Responses:Operation Completed
The specified change of administrative state has been perfomed:
JOB: 62
PC Time&Date: 16:35:12 03/23/2005
NE Time&Date: 16:33:06 09/15/2004
USER NAME: NSN
COMMAND: Unlock FCUMAIN:NAME=RACK:0/FCUMAIN:0;
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: Operation successful
administrativeState = Unlocked
END OF OUTPUT FOR JOB 62
CHANGED STATE EVENT REPORT:
This provides information about the administrative state, the operational state and the availability status every time a state change occurs:
JOB: 63
PC Time&Date: 16:35:12 03/23/2005
NE Time&Date: 16:33:06 09/15/2004
USER NAME: NSN
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: Operation successful
DN0933412 Issue 01441
BTSplus mainline commands at the Flexi BSC product family
FCUMAIN
Id:0900d805805b102f
CHANGED STATE EVENT REPORT:
NAME = RACK:0/FCUMAIN:0
Administrative State = UNLOCKED
Notification Identifier = 495
END OF OUTPUT FOR JOB 63
Operation Failed
The specified change of administrative state has not been performed.
Application Guidelines:None.
Example of Command Execution:Unlock FCUMAIN:NAME=RACK:0/FCUMANIN:0;
442DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805b1031
FCUTR
FCUTRThe FlexCU board is modeled with three HMO instances: 1 instance of the FCUMAIN HMO and 2 instances of the FCUTR HMO. The FCUMAIN instance represents that part of the board which performs board related activities and the FCUTR instances represent carrier (TRX) specific activities. There is a dependency of the FCUTR instances towards the FCUMAIN instance of a FlexCU.
CREATE FCUTR
Command Tree:“MANAGED-ELEMENT h BSS-EQUIPMENT h BTSEP h RACK h FCUTR h CREATE FCUTR”
Applicability:Phase 2 and Phase 3.
Visibility level: 2.
Command Description:This command adds the FCUTR unit to the BTSE data base.
Long Names:NAME Address of the managed object
TXLEVADJ txLevAdjust(dB)
System Responses:Operation Completed
After command execution, a message of Changed Configuration Notification is dis-played. A further message indicates the result of the operation. An example of create command is the following:
JOB: 56
PC Time&Date: 16:34:31 03/23/2005
NE Time&Date: 16:32:25 09/15/2004
USER NAME: NSN
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: Operation successful
ChangedConfigurationNotification:
name = RACK:0/FCUTR:0
CREATE FCUTR NAME=RACK:0..7/FCUTR:0..23 [,TXLEVADJ=];
DN0933412 Issue 01443
BTSplus mainline commands at the Flexi BSC product family
FCUTR
Id:0900d805805b1031
ChangeInfo = created
END OF OUTPUT FOR JOB 56
JOB: 57
PC Time&Date: 16:34:31 03/23/2005
NE Time&Date: 16:32:25 09/15/2004
USER NAME: NSN
COMMAND: Create FCUTR:NAME=RACK:0/FCUTR:0,TXLEVADJ=1;
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: Operation successful
txLevAdjust(dB) = 1.0
END OF OUTPUT FOR JOB 57
Operation Failed
The specified Object has not been created. In addition to the general NACK causes, a specific NACK cause, which indicates that the command is inconsistent with the physical configuration, is possible. An example is the following:
JOB: 76
PC Time&Date: 16:37:54 03/23/2005
NE Time&Date: 16:35:47 09/15/2004
USER NAME: NSN
COMMAND: Create FCUTR:NAME=RACK:0/FCUTR:0,TXLEVADJ=1;
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: Operation failed
txLevAdjust(dB) = 1.0
Creation out of sequence (-162)
END OF OUTPUT FOR JOB 76
Application Guidelines:None.
444DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805b1031
FCUTR
Example of Command Execution:Create FCUTR:NAME=RACK:0/FCUTR:0,TXLEVADJ=-20;
DELETE FCUTR
Command Tree:“MANAGED-ELEMENT h BSS-EQUIPMENT h BTSEP h RACK h FCUTR h DELETE FCUTR”
Applicability:Phase 2 and Phase 3.
Visibility level: 2.
Command Description:This command deletes the FCUTR unit from the BTSE data base.
Long Names:NAME Address of the managed object
System Responses:Operation Completed
After command execution, a message of Changed Configuration Notification is dis-played. A further message indicates the result of the operation. An example of delete command is the following:
JOB: 66
PC Time&Date: 16:35:23 03/23/2005
NE Time&Date: 16:33:17 09/15/2004
USER NAME: NSN
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: Operation successful
ChangedConfigurationNotification:
name = RACK:0/FCUTR:0
ChangeInfo = deleted
END OF OUTPUT FOR JOB 66
JOB: 67
DELETE FCUTR NAME=RACK:0..7/FCUTR:0..23;
DN0933412 Issue 01445
BTSplus mainline commands at the Flexi BSC product family
FCUTR
Id:0900d805805b1031
PC Time&Date: 16:35:23 03/23/2005
NE Time&Date: 16:33:17 09/15/2004
USER NAME: NSN
COMMAND: Delete FCUTR:NAME=RACK:0/FCUTR:0;
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: Operation successful
END OF OUTPUT FOR JOB 67
Operation Failed
The specified Object has not been deleted. Additionally to the general NACK causes, a specific NACK cause, meaning that the command is inconsistent with physical configu-ration, is possible.
Application Guidelines:None.
Example of Command Execution:Delete FCUTR:NAME=RACK:0/FCUTR:0;
GET FCUTR
Command Tree:“MANAGED-ELEMENT h BSS-EQUIPMENT h BTSEP h RACK h FCUTR h GET FCUTR”
Applicability:Phase 2 and Phase 3.
Visibility level: 0.
Command Description:This command displays the attributes of the FCUTR unit of the BTSE.
Long Names:NAME Address of the managed object
REQATTL Required attribute list
ALS alarmStatus
AST administrativeState
AVS availabilityStatus
CCPBL carrierCapability
GET FCUTR NAME=RACK:0..7/FCUTR:0..23 [,REQATTL=ALS, AST, AVS, CCPBL, OST, OUTPUTPR, PRS, RELFUNCOBJ, TXLEVADJ, STDBYST];
446DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805b1031
FCUTR
OST operationalState
OUTPUTPR outputPowerReduction
PRS proceduralStatus
RELFUNCOBJ relatedFuncObjects
TXLEVADJ txLevAdjust(dB)
STDBYST standbyStatus
System Responses:Operation Completed
After command execution, a message of Changed Configuration Notification is dis-played. A further message indicates the result of the operation. An example of get command is the following:
JOB: 59
PC Time&Date: 16:34:52 03/23/2005
NE Time&Date: 16:32:46 09/15/2004
USER NAME: NSN
COMMAND: Get FCUTR:NAME=RACK:0/FCUTR:0;
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT:Operation successful
alarmStatus = CLEARED
administrativeState = Unlocked
availabilityStatus = NULL
carrierCapability = edgeFourRxDiv
operationalState = ENABLED
outputPowerReduction = db0
proceduralStatus = NULL
relatedFuncObjects =
FMO = BTS:2/TRX:6
txLevAdjust(dB) = 0.0
END OF OUTPUT FOR JOB 59
Operation Failed
The GET command has not been successfully executed. A general NACK will indicate possible errors or a specific NACK strictly related to the single command is possible.
Application Guidelines:None.
Example of Command Execution:Get FCUTR:NAME=RACK:0/FCUTR:0,REQATTL=ALS&AST&AVS& CCPBL&OUT-PUTPR&OST&PRS&RELFUNCOBJ& TXLEVADJ;
DN0933412 Issue 01447
BTSplus mainline commands at the Flexi BSC product family
FCUTR
Id:0900d805805b1031
GETTEST FCUTR
Command Tree:“MANAGED-ELEMENT h BSS-EQUIPMENT h BTSEP h RACK h FCUTR h GETTEST FCUTR”
Applicability:Phase 2 and Phase 3.
Visibility level: 0.
Command Description:This command displays the attributes of the FCUTR test.
Long Names:NAME Address of the managed object
REQATTL Required attribute list
System Responses:Operation Completed
After command execution, a message of Changed Configuration Notification is dis-played. A further message indicates the result of the operation. An example of gettest command is the following:
JOB: 221
PC Time&Date: 12:13:58 03/23/2005
NE Time&Date: 13:15:33 09/15/2004
USER NAME: NSN
COMMAND: Gettest FCUTR:NAME=RACK:0/FCUTR:0;
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: Operation successful
MOT = RACK:0/FTNFP:0
testMonitor =
phaseId = PreliminaryTestsFCUTR
phaseStatus = Running
phaseId = CheckAlarmStatusFCUTR
phaseStatus = Waiting
phaseId = EndTestFCUTR
phaseStatus = Waiting
testOutcome = INCONCLUSIVE
GETTEST FCUTR NAME=RACK:0..7/FCUTR:0..23;
448DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805b1031
FCUTR
testState = INITIALIZING
END OF OUTPUT FOR JOB 221
Operation Failed
The GET command has not been successfully executed. A general NACK will indicate possible errors or a specific NACK strictly related to the single command is possible.
Application Guidelines:None.
Example of Command Execution:Gettest FCUTR:NAME=RACK:0/FCUTR:0;
LOCK FCUTR
Command Tree:“MANAGED-ELEMENT h BSS-EQUIPMENT h BTSEP h RACK h FCUTR h LOCK FCUTR”
Applicability:Phase 2 and Phase 3.
Visibility level: 1.
Command Description:This command changes the administrative state of the FCUTR object of the BTSE.
Long Names:NAME Address of the managed object
testMonitor it is a list of all test phases related to the selected object; for each phase the related phaseStatus is provided (Passed, Failed, Running or Waiting).
phaseId =
phaseStatus =
phaseId =
phaseStatus =
...
...
testOutcome It represents the test result: it can be Inconclusive (if the phases already executed were successful) or Fail (if at least one of the executed phases failed).
testState = Testing It can assume one of the following values: not_initialized, idle, initializing, sus-pended, testing, terminating and dis-abled.
LOCK FCUTR NAME=RACK:0..7/FCUTR:0..23;
DN0933412 Issue 01449
BTSplus mainline commands at the Flexi BSC product family
FCUTR
Id:0900d805805b1031
System Responses:Operation Completed
The specified change of administrative state has been perfomed:
JOB: 60
PC Time&Date: 16:35:08 03/23/2005
NE Time&Date: 16:33:02 09/15/2004
USER NAME: NSN
COMMAND: Lock FCUTR:NAME=RACK:0/FCUTR:0;
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: Operation successful
administrativeState = Locked
END OF OUTPUT FOR JOB 60
CHANGED STATE EVENT REPORT:
This provides information about the administrative state, the operational state and the availability status every time a state change occurs:
JOB: 61
PC Time&Date: 16:35:08 03/23/2005
NE Time&Date: 16:33:02 09/15/2004
USER NAME: NSN
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: Operation successful
CHANGED STATE EVENT REPORT:
NAME = RACK:0/FCUTR:0
Administrative State = LOCKED
Notification Identifier = 494
END OF OUTPUT FOR JOB 61
450DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805b1031
FCUTR
Operation Failed
The specified change of administrative state has not been performed.
Application Guidelines:None.
Example of Command Execution:Lock FCUTR:NAME=RACK:0/FCUTR:0;
PERFTEST FCUTR
Command Tree:“MANAGED-ELEMENT h BSS-EQUIPMENT h BTSEP h RACK h FCUTR h PERFTEST FCUTR”
Applicability:Phase 2 and Phase 3.
Visibility level: 1.
Command Description:This command is used to start an asynchronous test in FCUTR.
Long Names:NAME Address of the managed object
System Responses:Operation Completed
Test configuration has been set and the specified test has been started. The System response will not be addressed to the MOT but to the object BTSEP.
JOB: 222
PC Time&Date: 12:14:01 03/23/2005
NE Time&Date: 13:15:36 09/15/2004
USER NAME: NSN
COMMAND: Perftest FCUTR:NAME=RACK:0/FCUTR:0;
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: Operation successful
MOT = RACK:0/FCUTR:0
tO = BTSETEST:6
PERFTEST FCUTR NAME=RACK:0..7/FCUTR:0..23;
DN0933412 Issue 01451
BTSplus mainline commands at the Flexi BSC product family
FCUTR
Id:0900d805805b1031
END OF OUTPUT FOR JOB 222
JOB: 223
PC Time&Date: 12:14:01 03/23/2005
NE Time&Date: 13:15:36 09/15/2004
USER NAME: NSN
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: Operation successful
ChangedConfigurationNotification:
name = BTSETEST:6
ChangeInfo = created
END OF OUTPUT FOR JOB 223
JOB: 224
PC Time&Date: 12:14:01 03/23/2005
NE Time&Date: 13:15:36 09/15/2004
USER NAME: NSN
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: Operation successful
CHANGED STATE EVENT REPORT:
NAME = RACK:0/FCUTR:0
Operational State = ENABLED
Availability Status = NULL_value
Notification Identifier = 139
END OF OUTPUT FOR JOB 224
JOB: 225
452DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805b1031
FCUTR
PC Time&Date: 12:14:01 03/23/2005
NE Time&Date: 13:15:36 09/15/2004
USER NAME: NSN
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: Operation successful
Test Report:
name = BTSETEST:6
testOutcome = PASSED
testTermination = Normal
MOT = RACK:0/FCUTR:0
executedPhases =
PreliminaryTestsFCUTR
CheckAlarmStatusFCUTR
EndTestFCUTR
END OF OUTPUT FOR JOB 225
JOB: 226
PC Time&Date: 12:14:01 03/23/2005
NE Time&Date: 13:15:36 09/15/2004
USER NAME: NSN
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: Operation successful
ChangedConfigurationNotification:
name = BTSETEST:6
ChangeInfo = deleted
END OF OUTPUT FOR JOB 226
The test results will be displayed at the end of the test phases.
Result TEST:
DN0933412 Issue 01453
BTSplus mainline commands at the Flexi BSC product family
FCUTR
Id:0900d805805b1031
Operation Failed
This NACK-message occurs in the following cases: Message cannot be performed, test not supported, capacity restrictions, physical configuration cannot be performed, object not locked.
Application Guidelines:None.
Example of Command Execution:Perftest FCUTR:NAME=RACK:0/FCUTR:0;
name = TEST:<n>
testOutcome = This field represents the test result; one of the fol-lowing values can be displayed:
Pass all the test phases are successfully performed.
Inconclusive the test is aborted by the system or the test is terminated by the opera-tor.
Fail if at least one of the executed phases fail.
mOts = It is the identifier of the hardware object under test.
testTermination = It specifies how the test is terminated, it can assume the following values:
Normal all the test phases are performed.
Abort the test is aborted by system.
Cancel the test is terminated by operator.
executedPhases
phaseId = It represents the list of the executed test phases (in case of successful test result, all the test phases will be listed).
additionalWords =
....
failedPhases
phaseId = It represents the list of the failed test phase; addi-tional information is provided for each phase.phaseId =
....
skippedPhases
phaseId = It represents the list of the skipped phases; they are displayed only for test stopped during it execution.phaseId =
....
poprosedRepair Action =
A list of most probable fail probable causes is shown (max four messages)
454DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805b1031
FCUTR
SET FCUTR
Command Tree:“MANAGED-ELEMENT h BSS-EQUIPMENT h BTSEP h RACK h FCUTR h SET FCUTR”
Applicability:Phase 2 and Phase 3.
Visibility level: 2.
Command Description:This command is used to set the attributes of the specified RACK.
Long Names:NAME Address of the managed object
TXLEVADJ txLevAdjust(dB)
System Responses:Operation Completed
After command execution, a message of Changed Attribute Event Report is displayed. A further message indicates the result of the operation. An example of set command is the following:
JOB: 176
PC Time&Date: 12:05:36 03/23/2005
NE Time&Date: 13:07:12 09/15/2004
USER NAME: NSN
COMMAND: Set FCUTR:NAME=RACK:0/FCUTR:0;
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: Operation successful
END OF OUTPUT FOR JOB 176
Operation Failed
The specified attributes have not been set. In addition to the general NACK causes, a specific NACK cause, which indicates that the command is inconsistent with the physical configuration, is possible.
Application Guidelines:None.
Example of Command Execution:Set FCUTR:NAME=RACK:0/FCUTR:0;
SET FCUTR NAME=RACK:0..7/FCUTR:0..23 [,TXLEVADJ=];
DN0933412 Issue 01455
BTSplus mainline commands at the Flexi BSC product family
FCUTR
Id:0900d805805b1031
STOPTEST FCUTR
Command Tree:“MANAGED-ELEMENT h BSS-EQUIPMENT h BTSEP h RACK h FCUTR h STOPTEST FCUTR”
Applicability:Phase 2 and Phase 3.
Visibility level: 1.
Command Description:This command is used to stop a diagnostic previously started.
Long Names:NAME Address of the managed object
System Responses:Operation Completed
Test has been stopped. The System Responses will not be addressed to the MOT but to the object BTSEP.
Operation Failed
Test has not been stopped. This NACK-message can occur when the specified test is not running or in case of test which cannot be stopped.
STOPTEST FCUTR NAME=RACK:0..7/FCUTR:0..23;
Result TEST:
name = TEST:<n>
testOutcome = inconclusive
mOts = It is the identifier of the hardware object under test.
testTermination = Cancel
executedPhases
phaseId = It represents the list of the executed test phases; the list is not shown for test in the waiting list (queued)....
.
failedPhases
phaseId = It represents the list of the failed test phase;
additional information is provided for each phase.phaseId =
....
skippedPhases
phaseId = It represents the list of the skipped phases;the list is not shown for test in the waiting list (queued).phaseId =
456DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805b1031
FCUTR
Application Guidelines:None.
Example of Command Execution:Stoptest FCUTR:NAME=RACK:0/FCUTR:0;
UNLOCK FCUTR
Command Tree:“MANAGED-ELEMENT h BSS-EQUIPMENT h BTSEP h RACK h FCUTR h UNLOCK FCUTR”
Applicability:Phase 2 and Phase 3.
Visibility level: 1.
Command Description:This command changes the administrative state of the FCUTR object of the BTSE.
Long Names:NAME Address of the managed object
System Responses:Operation Completed
The specified change of administrative state has been perfomed:
JOB: 62
PC Time&Date: 16:35:12 03/23/2005
NE Time&Date: 16:33:06 09/15/2004
USER NAME: NSN
COMMAND: Unlock FCUTR:NAME=RACK:0/FCUTR:0;
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: Operation successful
administrativeState = Unlocked
END OF OUTPUT FOR JOB 62
CHANGED STATE EVENT REPORT:
UNLOCK FCUTR NAME=RACK:0..7/FCUTR:0..23;
DN0933412 Issue 01457
BTSplus mainline commands at the Flexi BSC product family
FCUTR
Id:0900d805805b1031
This provides information about the administrative state, the operational state and the availability status every time a state change occurs:
JOB: 63
PC Time&Date: 16:35:12 03/23/2005
NE Time&Date: 16:33:06 09/15/2004
USER NAME: NSN
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: Operation successful
CHANGED STATE EVENT REPORT:
NAME = RACK:0/FCUTR:0
Administrative State = UNLOCKED
Notification Identifier = 495
END OF OUTPUT FOR JOB 63
Operation Failed
The specified change of administrative state has not been performed.
Application Guidelines:None.
Example of Command Execution:Unlock FCUTR:NAME=RACK:0/FCUTR:0;
458DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805b1033
FTNFP
FTNFPThe FTNFP object represents the hardware of the tunable filters in dowlink direction.
CREATE FTNFP
Command Tree:“MANAGED-ELEMENT h BSS-EQUIPMENT h BTSEP h RACK h FTNFP h CREATE FTNFP”
Applicability:Phase 2 and Phase 3.
Visibility level: 2.
Command Description:This command adds the FICOM_TNF unit to the BTSE data base.
Long Names:NAME Address of the managed object
CELLNO cellNumber
WDFTNFP wiringDataFtnfp
System Responses:Operation Completed
After command execution, a message of Changed Configuration Notification is dis-played. A further message indicates the result of the operation. An example of create command is the following:
JOB: 56
PC Time&Date: 16:34:31 03/23/2005
NE Time&Date: 16:32:25 09/15/2004
USER NAME: NSN
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: Operation successful
ChangedConfigurationNotification:
name = RACK:0/FTNFP:0
ChangeInfo = created
END OF OUTPUT FOR JOB 56
CREATE FTNFP NAME=RACK:0..7/FTNFP:0..7 ,CELLNO= ,WDFTNFP=;
DN0933412 Issue 01459
BTSplus mainline commands at the Flexi BSC product family
FTNFP
Id:0900d805805b1033
JOB: 57
PC Time&Date: 16:34:31 03/23/2005
NE Time&Date: 16:32:25 09/15/2004
USER NAME: NSN
COMMAND: Create FTNFP:NAME=RACK:0/FTNFP:0,CELLNO=1,WDFT-NFP=CU0-FVSWRP0;
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: Operation successful
cellNumber = 1
wiringDataFtnfp =
CUWiring = CU0
FVSWRPWiring = FVSWRP0
END OF OUTPUT FOR JOB 57
Operation Failed
The specified Object has not been created. In addition to the general NACK causes, a specific NACK cause, which indicates that the command is inconsistent with the physical configuration, is possible. An example is the following:
JOB: 76
PC Time&Date: 16:37:54 03/23/2005
NE Time&Date: 16:35:47 09/15/2004
USER NAME: NSN
COMMAND: Create FTNFP:NAME=RACK:0/FTNFP:0,CELLNO=1,WDFT-NFP=CU0-FVSWRP0;
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: OPERATION FAILED
Message cannot be performed (-17)
END OF OUTPUT FOR JOB 76
Application Guidelines:
• The FICOM_TNFP, the CU and the FICOM_VSWRP are in the same rack and belong to the same cell
460DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805b1033
FTNFP
Example of Command Execution:Create FTNFP:NAME=RACK:0/FTNFP:0,CELLNO=0,WDFTNFP=CU0-FVSWRP0;
DELETE FTNFP
Command Tree:“MANAGED-ELEMENT h BSS-EQUIPMENT h BTSEP h RACK h FTNFP h DELETE FTNFP”
Applicability:Phase 2 and Phase 3.
Visibility level: 2.
Command Description:This command deletes the FICOM_TNF unit from the BTSE data base.
Long Names:NAME Address of the managed object
System Responses:Operation Completed
After command execution, a message of Changed Configuration Notification is dis-played. A further message indicates the result of the operation. An example of delete command is the following:
JOB: 66
PC Time&Date: 16:35:23 03/23/2005
NE Time&Date: 16:33:17 09/15/2004
USER NAME: NSN
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: Operation successful
ChangedConfigurationNotification:
name = RACK:0/FTNFP:0
ChangeInfo = deleted
END OF OUTPUT FOR JOB 66
JOB: 67
DELETE FTNFP NAME=RACK:0..7/FTNFP:0..7;
DN0933412 Issue 01461
BTSplus mainline commands at the Flexi BSC product family
FTNFP
Id:0900d805805b1033
PC Time&Date: 16:35:23 03/23/2005
NE Time&Date: 16:33:17 09/15/2004
USER NAME: NSN
COMMAND: Delete FTNFP:NAME=RACK:0/FTNFP:0;
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: Operation successful
END OF OUTPUT FOR JOB 67
Operation Failed
The specified Object has not been deleted. Additionally to the general NACK causes, a specific NACK cause, meaning that the command is inconsistent with physical configu-ration, is possible.
Application Guidelines:
• FTNFP must be locked in Phase 3, before deletion
• If this object is deleted, the related TRX is out of service
Example of Command Execution:Delete FTNFP:NAME=RACK:0/FTNFP:0;
GET FTNFP
Command Tree:“MANAGED-ELEMENT h BSS-EQUIPMENT h BTSEP h RACK h FTNFP h GET FTNFP”
Applicability:Phase 2 and Phase 3.
Visibility level: 0.
Command Description:This command displays the attributes of the FICOM_TNF unit of the BTSE.
Long Names:NAME Address of the managed object
REQATTL Required attribute list
ALS alarmStatus
AST administrativeState
AVS availabilityStatus
GET FTNFP NAME=RACK:0..7/FTNFP:0..7 [,REQATTL=ALS, AST, AVS, CELLNO, OST, PRS, RELFUNCOBJ, TNFTARGF, WDFTNFP];
462DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805b1033
FTNFP
CELLNO cellNumber
OST operationalState
PRS proceduralStatus
RELFUNCOBJ relatedFuncObjects
TNFTARGF tnfTargetFrequency
WDFTNFP wiringDataFtnfp
System Responses:Operation Completed
After command execution, a message of Changed Configuration Notification is dis-played. A further message indicates the result of the operation. An example of get command is the following:
JOB: 59
PC Time&Date: 16:34:52 03/23/2005
NE Time&Date: 16:32:46 09/15/2004
USER NAME: NSN
COMMAND: Get FTNFP:NAME=RACK:0/FTNFP:0;
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: Operation successful
alarmStatus = CLEARED
administrativeState = Unlocked
availabilityStatus = NotInstalled
cellNumber = 1
operationalState = DISABLED
proceduralStatus = NULL
relatedFuncObjects =
tnfTargetFrequency = Null
wiringDataFtnfp =
CUWiring = CU0
FVSWRPWiring = FVSWRP0
END OF OUTPUT FOR JOB 59
Operation Failed
The GET command has not been successfully executed. A general NACK will indicate possible errors or a specific NACK strictly related to the single command is possible.
DN0933412 Issue 01463
BTSplus mainline commands at the Flexi BSC product family
FTNFP
Id:0900d805805b1033
Application Guidelines:
• The value for the attribute relatedFuncObjects in LMT Phase 2 is "not configured"
• For list of extended values / wiringDataFtnfp refer to Chapter 9 of the FS
Example of Command Execution:Get FTNFP:NAME=RACK:0/FTNFP:0,REQATTL=ALS&AST&AVS&CELLNO&
RELFUNCOBJ&OST&PRS&TNFTARGF&WDFTNFP;
GETTEST FTNFP
Command Tree:“MANAGED-ELEMENT h BSS-EQUIPMENT h BTSEP h RACK h FTNFP h GETTEST FTNFP”
Applicability:Phase 2 and Phase 3.
Visibility level: 0.
Command Description:This command displays the attributes of the FTNFP test.
Long Names:NAME Address of the managed object
REQATTL Required attribute list
System Responses:Operation Completed
After command execution, a message of Changed Configuration Notification is dis-played. A further message indicates the result of the operation. An example of gettest command is the following:
JOB: 221
PC Time&Date: 12:13:58 03/23/2005
NE Time&Date: 13:15:33 09/15/2004
USER NAME: NSN
COMMAND: Gettest FTNFP:NAME=RACK:0/FTNFP:0;
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: Operation successful
MOT = RACK:0/FTNFP:0
testMonitor =
GETTEST FTNFP NAME=RACK:0..7/FTNFP:0..7;
464DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805b1033
FTNFP
phaseId = PreliminaryTestsFtnfp
phaseStatus = Running
phaseId = CheckAlarmStatusFtnfp
phaseStatus = Waiting
phaseId = EndTestFtnfp
phaseStatus = Waiting
testOutcome = INCONCLUSIVE
testState = INITIALIZING
END OF OUTPUT FOR JOB 221
Operation Failed
The GET command has not been successfully executed. A general NACK will indicate possible errors or a specific NACK strictly related to the single command is possible.
Application Guidelines:None.
Example of Command Execution:Gettest FTNFP:NAME=RACK:0/FTNFP:0;
LOCK FTNFP
Command Tree:“MANAGED-ELEMENT h BSS-EQUIPMENT h BTSEP h RACK h FTNFP h LOCK FTNFP”
testMonitor it is a list of all test phases related to the selected object; for each phase the related phaseStatus is provided (Passed, Failed, Running or Waiting).
phaseId =
phaseStatus =
phaseId =
phaseStatus =
...
...
testOutcome It represents the test result: it can be Inconclusive (if the phases already executed were successful) or Fail (if at least one of the executed phases failed).
testState = Testing It can assume one of the following values: not_initialized, idle, initializing, sus-pended, testing, terminating and dis-abled.
LOCK FTNFP NAME=RACK:0..7/FTNFP:0..7;
DN0933412 Issue 01465
BTSplus mainline commands at the Flexi BSC product family
FTNFP
Id:0900d805805b1033
Applicability:Phase 2 and Phase 3.
Visibility level: 1.
Command Description:This command changes the administrative state of the FICOM_TNF object of the BTSE.
Long Names:NAME Address of the managed object
System Responses:Operation Completed
The specified change of administrative state has been perfomed:
JOB: 60
PC Time&Date: 16:35:08 03/23/2005
NE Time&Date: 16:33:02 09/15/2004
USER NAME: NSN
COMMAND: Lock FTNFP:NAME=RACK:0/FTNFP:0;
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: Operation successful
administrativeState = Locked
END OF OUTPUT FOR JOB 60
CHANGED STATE EVENT REPORT:
This provides information about the administrative state, the operational state and the availability status every time a state change occurs:
JOB: 61
PC Time&Date: 16:35:08 03/23/2005
NE Time&Date: 16:33:02 09/15/2004
USER NAME: NSN
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: Operation successful
466DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805b1033
FTNFP
CHANGED STATE EVENT REPORT:
NAME = RACK:0/FTNFP:0
Administrative State = LOCKED
Notification Identifier = 494
END OF OUTPUT FOR JOB 61
Operation Failed
The specified change of administrative state has not been performed.
Application Guidelines:None.
Example of Command Execution:Lock FTNFP:NAME=RACK:0/FTNFP:0
PERFTEST FTNFP
Command Tree:“MANAGED-ELEMENT h BSS-EQUIPMENT h BTSEP h RACK h FTNFP h PERFTEST FTNFP”
Applicability:Phase 2 and Phase 3.
Visibility level: 1.
Command Description:This command is used to start an asynchronous test in FTNFP.
Long Names:NAME Address of the managed object
System Responses:Operation Completed
Test configuration has been set and the specified test has been started. The System response will not be addressed to the MOT but to the object BTSEP.
JOB: 222
PC Time&Date: 12:14:01 03/23/2005
NE Time&Date: 13:15:36 09/15/2004
PERFTEST FTNFP NAME=RACK:0..7/FTNFP:0..7;
DN0933412 Issue 01467
BTSplus mainline commands at the Flexi BSC product family
FTNFP
Id:0900d805805b1033
USER NAME: NSN
COMMAND: Perftest FTNFP:NAME=RACK:0/FTNFP:0;
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: Operation successful
MOT = RACK:0/FTNFP:0
tO = BTSETEST:6
END OF OUTPUT FOR JOB 222
JOB: 223
PC Time&Date: 12:14:01 03/23/2005
NE Time&Date: 13:15:36 09/15/2004
USER NAME: NSN
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: Operation successful
ChangedConfigurationNotification:
name = BTSETEST:6
ChangeInfo = created
END OF OUTPUT FOR JOB 223
JOB: 224
PC Time&Date: 12:14:01 03/23/2005
NE Time&Date: 13:15:36 09/15/2004
USER NAME: NSN
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: Operation successful
CHANGED STATE EVENT REPORT:
NAME = RACK:0/FTNFP:0
468DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805b1033
FTNFP
Operational State = ENABLED
Availability Status = NULL_value
Notification Identifier = 139
END OF OUTPUT FOR JOB 224
JOB: 225
PC Time&Date: 12:14:01 03/23/2005
NE Time&Date: 13:15:36 09/15/2004
USER NAME: NSN
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: Operation successful
Test Report:
name = BTSETEST:6
testOutcome = PASSED
testTermination = Normal
MOT = RACK:0/FTNFP:0
executedPhases =
PreliminaryTestsFtnfp
CheckAlarmStatusFtnfp
EndTestFtnfp
END OF OUTPUT FOR JOB 225
JOB: 226
PC Time&Date: 12:14:01 03/23/2005
NE Time&Date: 13:15:36 09/15/2004
USER NAME: NSN
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: Operation successful
ChangedConfigurationNotification:
DN0933412 Issue 01469
BTSplus mainline commands at the Flexi BSC product family
FTNFP
Id:0900d805805b1033
name = BTSETEST:6
ChangeInfo = deleted
END OF OUTPUT FOR JOB 226
Operation Failed
The test results will be displayed at the end of the test phases.
Result TEST:
name = TEST:<n>
testOutcome = This field represents the test result; one of the fol-lowing values can be displayed:
Pass all the test phases are successfully performed.
Inconclusive the test is aborted by the system or the test is terminated by the opera-tor.
Fail if at least one of the executed phases fail.
mOts = It is the identifier of the hardware object under test.
testTermination = It specifies how the test is terminated, it can assume the following values:
Normal all the test phases are performed.
Abort the test is aborted by system.
Cancel the test is terminated by operator.
executedPhases
phaseId = It represents the list of the executed test phases (in case of successful test result, all the test phases will be listed).
additionalWords =
....
failedPhases
phaseId = It represents the list of the failed test phase; addi-tional information is provided for each phase.phaseId =
....
skippedPhases
phaseId = It represents the list of the skipped phases; they are displayed only for test stopped during it execution.phaseId =
....
poprosedRepair Action =
A list of most probable fail probable causes is shown (max four messages)
470DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805b1033
FTNFP
This NACK-message occurs in the following cases: Message cannot be performed, test not supported, capacity restrictions, physical configuration cannot be performed, object not locked.
Application Guidelines:
• In phase 3 MO must be locked previous to the command execution
Example of Command Execution:Perftest FTNFP:NAME=RACK:0/FTNFP:0;
STOPTEST FTNFP
Command Tree:“MANAGED-ELEMENT h BSS-EQUIPMENT h BTSEP h RACK h FTNFP h STOPTEST FTNFP”
Applicability:Phase 2 and Phase 3.
Visibility level: 1.
Command Description:This command is used to stop a diagnostic previously started.
Long Names:NAME Address of the managed object
System Responses:Operation Completed
Test has been stopped. The System Responses will not be addressed to the MOT but to the object BTSEP.
STOPTEST FTNFP NAME=RACK:0..7/FTNFP:0..7;
Result TEST:
name = TEST:<n>
testOutcome = inconclusive
mOts = It is the identifier of the hardware object under test.
testTermination = Cancel
executedPhases
phaseId = It represents the list of the executed test phases; the list is not shown for test in the waiting list (queued)....
.
failedPhases
DN0933412 Issue 01471
BTSplus mainline commands at the Flexi BSC product family
FTNFP
Id:0900d805805b1033
Operation Failed
Test has not been stopped. This NACK-message can occur when the specified test is not running or in case of test which cannot be stopped.
Application Guidelines:None.
Example of Command Execution:Stoptest FTNFP:NAME=RACK:0/FTNFP:0;
UNLOCK FTNFP
Command Tree:“MANAGED-ELEMENT h BSS-EQUIPMENT h BTSEP h RACK h FTNFP h UNLOCK FTNFP”
Applicability:Phase 2 and Phase 3.
Visibility level: 1.
Command Description:This command changes the administrative state of the FICOM_TNF object of the BTSE.
Long Names:NAME Address of the managed object
System Responses:Operation Completed
The specified change of administrative state has been perfomed:
JOB: 62
PC Time&Date: 16:35:12 03/23/2005
NE Time&Date: 16:33:06 09/15/2004
USER NAME: NSN
phaseId = It represents the list of the failed test phase;
additional information is provided for each phase.phaseId =
....
skippedPhases
phaseId = It represents the list of the skipped phases;the list is not shown for test in the waiting list (queued).phaseId =
UNLOCK FTNFP NAME=RACK:0..7/FTNFP:0..7;
472DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805b1033
FTNFP
COMMAND: Unlock FTNFP:NAME=RACK:0/FTNFP:0;
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: Operation successful
administrativeState = Unlocked
END OF OUTPUT FOR JOB 62
CHANGED STATE EVENT REPORT:
This provides information about the administrative state, the operational state and the availability status every time a state change occurs:
JOB: 63
PC Time&Date: 16:35:12 03/23/2005
NE Time&Date: 16:33:06 09/15/2004
USER NAME: NSN
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: Operation successful
CHANGED STATE EVENT REPORT:
NAME = RACK:0/FTNFP:0
Administrative State = UNLOCKED
Notification Identifier = 495
END OF OUTPUT FOR JOB 63
Operation Failed
The specified change of administrative state has not been performed.
Application Guidelines:None.
Example of Command Execution:Unlock FTNFP:NAME=RACK:0/FTNFP:0;
DN0933412 Issue 01473
BTSplus mainline commands at the Flexi BSC product family
FVSWRP
Id:0900d805805b1035
FVSWRPThe FVSWRP object represents the hardware of the tunable filters in the dowlink direc-tion. There is only one FVSWR per cell, which performs also some functionalities common to the cell (e.g. alarm generation).
CREATE FVSWRP
Command Tree:“MANAGED-ELEMENT h BSS-EQUIPMENT h BTSEP h RACK h FVSWRP h CREATE FVSWRP”
Applicability:Phase 2 and Phase 3.
Visibility level: 2.
Command Description:This command adds the FICOM_VSWR unit to the BTSE data base.
Long Names:NAME Address of the managed object
CELLNO cellNumber
System Responses:Operation Completed
After command execution, a message of Changed Configuration Notification is dis-played. A further message indicates the result of the operation. An example of create command is the following:
JOB: 40
PC Time&Date: 16:31:19 03/23/2005
NE Time&Date: 16:29:13 09/15/2004
USER NAME: NSN_Ross
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: Operation successful
ChangedConfigurationNotification:
name = RACK:0/FVSWRP:0
ChangeInfo = created
CREATE FVSWRP NAME=RACK:0..7/FVSWRP:0..3 ,CELLNO=;
474DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805b1035
FVSWRP
END OF OUTPUT FOR JOB 40
JOB: 41
PC Time&Date: 16:31:19 03/23/2005
NE Time&Date: 16:29:13 09/15/2004
USER NAME: NSN_Ross
COMMAND: Create FVSWRP:NAME=RACK:0/FVSWRP:0,CELLNO=1;
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: Operation successful
cellNumber = 1
END OF OUTPUT FOR JOB 41
Operation Failed
The specified Object has not been created. In addition to the general NACK causes, a specific NACK cause, which indicates that the command is inconsistent with the physical configuration, is possible. An example is the following:
JOB: 77
PC Time&Date: 16:37:54 03/23/2005
NE Time&Date: 16:35:47 09/15/2004
USER NAME: NSN_Ross
COMMAND: Create FVSWRP:NAME=RACK:0/FVSWRP:0,CELLNO=1;
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: OPERATION FAILED
Object instance unknown (-9)
END OF OUTPUT FOR JOB 77
Application Guidelines:None.
Example of Command Execution:Create FVSWRP:NAME=RACK:0/FVSWRP:0,CELLNO=0;
DN0933412 Issue 01475
BTSplus mainline commands at the Flexi BSC product family
FVSWRP
Id:0900d805805b1035
DELETE FVSWRP
Command Tree:“MANAGED-ELEMENT h BSS-EQUIPMENT h BTSEP h RACK h FVSWRP h DELETE FVSWRP”
Applicability:Phase 2 and Phase 3.
Visibility level: 2.
Command Description:This command deletes the FICOM_VSWR unit from the BTSE data base.
Long Names:NAME Address of the managed object
System Responses:Operation Completed
After command execution, a message of Changed Configuration Notification is dis-played. A further message indicates the result of the operation. An example of delete command is the following:
JOB: 51
PC Time&Date: 16:33:29 03/23/2005
NE Time&Date: 16:31:23 09/15/2004
USER NAME: NSN_Ross
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: Operation successful
ChangedConfigurationNotification:
name = RACK:0/FVSWRP:0
ChangeInfo = deleted
END OF OUTPUT FOR JOB 51
JOB: 52
PC Time&Date: 16:33:29 03/23/2005
NE Time&Date: 16:31:23 09/15/2004
DELETE FVSWRP NAME=RACK:0..7/FVSWRP:0..3;
476DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805b1035
FVSWRP
USER NAME: NSN_Ross
COMMAND: Delete FVSWRP:NAME=RACK:0/FVSWRP:0;
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: Operation successful
END OF OUTPUT FOR JOB 52
Operation Failed
The specified Object has not been deleted. Additionally to the general NACK causes, a specific NACK cause, meaning that the command is inconsistent with physical configu-ration, is possible.
Application Guidelines:
• FVSWRP must be locked in Phase 3, before deletion
• If this object is deleted, the related TRXs are out of service
Example of Command Execution:Delete FVSWRP:NAME=RACK:0/FVSWRP:0;
GET FVSWRP
Command Tree:“MANAGED-ELEMENT h BSS-EQUIPMENT h BTSEP h RACK h FVSWRP h GET FVSWRP”
Applicability:Phase 2 and Phase 3.
Visibility level: 0.
Command Description:This command displays the attributes of the FICOM_VSWR unit of the BTSE.
Long Names:NAME Address of the managed object
REQATTL Required attribute list
ALS alarmStatus
AST administrativeState
AVS availabilityStatus
CELLNO cellNumber
OST operationalState
PRS proceduralStatus
RELFUNCOBJ relatedFuncObjects
GET FVSWRP NAME=RACK:0..7/FVSWRP:0..3 [,REQATTL=ALS, AST, AVS, CELLNO, OST, PRS, RELFUNCOBJ];
DN0933412 Issue 01477
BTSplus mainline commands at the Flexi BSC product family
FVSWRP
Id:0900d805805b1035
System Responses:Operation Completed
After command execution, a message of Changed Configuration Notification is dis-played. A further message indicates the result of the operation. An example of get command is the following:
JOB: 43
PC Time&Date: 16:32:46 03/23/2005
NE Time&Date: 16:30:40 09/15/2004
USER NAME: NSN_Ross
COMMAND: Get FVSWRP:NAME=RACK:0/FVSWRP:0;
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: Operation successful
alarmStatus = CLEARED
administrativeState = Unlocked
availabilityStatus = NotInstalled
cellNumber = 1
operationalState = DISABLED
proceduralStatus = NULL
relatedFuncObjects =
END OF OUTPUT FOR JOB 43
Operation Failed
The GET command has not been successfully executed. A general NACK will indicate possible errors or a specific NACK strictly related to the single command is possible.
Application Guidelines:
• The value for the attribute relatedFuncObjects in LMT Phase 2 is "not configured"
Example of Command Execution:Get FVSWRP:NAME=RACK:0/FVSWRP:0,REQATTL=ALS&AST&AVS&CELLNO&
RELFUNCOBJ&OST&PRS;
GETTEST FVSWRP
Command Tree:“MANAGED-ELEMENT h BSS-EQUIPMENT h BTSEP h RACK h FVSWRP h GETTEST FVSWRP”
GETTEST FVSWRP NAME=RACK:0..7/FVSWRP:0..3;
478DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805b1035
FVSWRP
Applicability:Phase 2 and Phase 3.
Visibility level: 0.
Command Description:This command displays the attributes of the FVSWRP test.
Long Names:NAME Address of the managed object
REQATTL Required attribute list
System Responses:Operation Completed
After command execution, a message of Changed Configuration Notification is dis-played. A further message indicates the result of the operation. An example of gettest command is the following:
JOB: 227
PC Time&Date: 12:14:01 03/23/2005
NE Time&Date: 13:15:36 09/15/2004
USER NAME: NSN_Ross
COMMAND: Gettest FVSWRP:NAME=RACK:0/FVSWRP:0;
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: Operation successful
MOT = RACK:0/FVSWRP:0
testMonitor =
phaseId = PreliminaryTestsFvswrp
phaseStatus = Running
phaseId = CheckAlarmStatusFvswrp
phaseStatus = Waiting
phaseId = EndTestFvswrp
phaseStatus = Waiting
testOutcome = INCONCLUSIVE
testState = INITIALIZING
END OF OUTPUT FOR JOB 227
Operation Failed
The GET command has not been successfully executed. A general NACK will indicate possible errors or a specific NACK strictly related to the single command is possible.
DN0933412 Issue 01479
BTSplus mainline commands at the Flexi BSC product family
FVSWRP
Id:0900d805805b1035
Application Guidelines:None.
Example of Command Execution:Gettest FVSWRP:NAME=RACK:0/FVSWRP:0;
LOCK FVSWRP
Command Tree:“MANAGED-ELEMENT h BSS-EQUIPMENT h BTSEP h RACK h FVSWRP h LOCK FVSWRP”
Applicability:Phase 2 and Phase 3.
Visibility level: 1.
Command Description:This command changes the administrative state of FICOM_VSWR unit of the BTSE.
Long Names:NAME Address of the managed object
System Responses:Operation Completed
The specified change of administrative state has been perfomed:
JOB: 45
testMonitor it is a list of all test phases related to the selected object; for each phase the related phaseStatus is provided (Passed, Failed, Running or Waiting).
phaseId =
phaseStatus =
phaseId =
phaseStatus =
...
...
testOutcome It represents the test result: it can be Inconclusive (if the phases already executed were successful) or Fail (if at least one of the executed phases failed).
testState = Testing It can assume one of the following values: not_initialized, idle, initializing, sus-pended, testing, terminating and dis-abled.
LOCK FVSWRP NAME=RACK:0..7/FVSWRP:0..3;
480DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805b1035
FVSWRP
PC Time&Date: 16:33:14 03/23/2005
NE Time&Date: 16:31:08 09/15/2004
USER NAME: NSN_Ross
COMMAND: Lock FVSWRP:NAME=RACK:0/FVSWRP:0;
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: Operation successful
administrativeState = Locked
END OF OUTPUT FOR JOB 45
CHANGED STATE EVENT REPORT:
This provides information about the administrative state, the operational state and the availability status every time a state change occurs:
JOB: 46
PC Time&Date: 16:33:14 03/23/2005
NE Time&Date: 16:31:08 09/15/2004
USER NAME: NSN_Ross
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: Operation successful
CHANGED STATE EVENT REPORT:
NAME = RACK:0/FVSWRP:0
Administrative State = LOCKED
Notification Identifier = 487
END OF OUTPUT FOR JOB 46
Operation Failed
The specified change of administrative state has not been performed.
Application Guidelines:None.
DN0933412 Issue 01481
BTSplus mainline commands at the Flexi BSC product family
FVSWRP
Id:0900d805805b1035
Example of Command Execution:Lock FVSWRP:NAME=RACK:0/FVSWRP:0;
PERFTEST FVSWRP
Command Tree:“MANAGED-ELEMENT h BSS-EQUIPMENT h BTSEP h RACK h FVSWRP h PERFTEST FVSWRP”
Applicability:Phase 2 and Phase 3.
Visibility level: 1.
Command Description:This command is used to start an asynchronous test in FVSWRP.
Long Names:NAME Address of the managed object
System Responses:Operation Completed
Test configuration has been set and the specified test has been started. The System response will not be addressed to the MOT but to the object BTSEP.
JOB: 228
PC Time&Date: 12:14:07 03/23/2005
NE Time&Date: 13:15:42 09/15/2004
USER NAME: NSN_Ross
COMMAND: Perftest FVSWRP:NAME=RACK:0/FVSWRP:0;
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: Operation successful
MOT = RACK:0/FVSWRP:0
tO = BTSETEST:1
END OF OUTPUT FOR JOB 228
JOB: 229
PERFTEST FVSWRP NAME=RACK:0..7/FVSWRP:0..3;
482DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805b1035
FVSWRP
PC Time&Date: 12:14:18 03/23/2005
NE Time&Date: 13:15:49 09/15/2004
USER NAME: NSN_Ross
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: Operation successful
ChangedConfigurationNotification:
name = BTSETEST:1
ChangeInfo = created
END OF OUTPUT FOR JOB 229
JOB: 230
PC Time&Date: 12:14:18 03/23/2005
NE Time&Date: 13:15:49 09/15/2004
USER NAME: NSN_Ross
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: Operation successful
CHANGED STATE EVENT REPORT:
NAME = RACK:0/FVSWRP:0
Operational State = ENABLED
Availability Status = NULL_value
Notification Identifier = 238
END OF OUTPUT FOR JOB 230
JOB: 231
PC Time&Date: 12:14:23 03/23/2005
NE Time&Date: 13:15:52 09/15/2004
USER NAME: NSN_Ross
DN0933412 Issue 01483
BTSplus mainline commands at the Flexi BSC product family
FVSWRP
Id:0900d805805b1035
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: Operation successful
Test Report:
name = BTSETEST:1
testOutcome = PASSED
testTermination = Normal
MOT = RACK:0/FVSWRP:0
executedPhases =
PreliminaryTestsFvswrp
CheckAlarmStatusFvswrp
EndTestFvswrp
END OF OUTPUT FOR JOB 231
JOB: 232
PC Time&Date: 12:14:41 03/23/2005
NE Time&Date: 13:16:05 09/15/2004
USER NAME: NSN_Ross
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: Operation successful
ChangedConfigurationNotification:
name = BTSETEST:1
ChangeInfo = deleted
END OF OUTPUT FOR JOB 232
The test results will be displayed at the end of the test phases.
Result TEST:
name = TEST:<n>
testOutcome = This field represents the test result; one of the fol-lowing values can be displayed:
Pass all the test phases are successfully performed.
484DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805b1035
FVSWRP
Operation Failed
This NACK-message occurs in the following cases: Message cannot be performed, test not supported, capacity restrictions, physical configuration cannot be performed, object not locked.
Application Guidelines:
• In phase 3 MO must be locked previous to the command execution
Example of Command Execution:Perftest FVSWRP:NAME=RACK:0/FVSWRP:0;
STOPTEST FVSWRP
Inconclusive the test is aborted by the system or the test is terminated by the opera-tor.
Fail if at least one of the executed phases fail.
mOts = It is the identifier of the hardware object under test.
testTermination = It specifies how the test is terminated, it can assume the following values:
Normal all the test phases are performed.
Abort the test is aborted by system.
Cancel the test is terminated by operator.
executedPhases
phaseId = It represents the list of the executed test phases (in case of successful test result, all the test phases will be listed).
additionalWords =
....
failedPhases
phaseId = It represents the list of the failed test phase; addi-tional information is provided for each phase.phaseId =
....
skippedPhases
phaseId = It represents the list of the skipped phases; they are displayed only for test stopped during it execution.phaseId =
....
poprosedRepair Action =
A list of most probable fail probable causes is shown (max four messages)
STOPTEST FVSWRP NAME=RACK:0..7/FVSWRP:0..3;
DN0933412 Issue 01485
BTSplus mainline commands at the Flexi BSC product family
FVSWRP
Id:0900d805805b1035
Command Tree:“MANAGED-ELEMENT h BSS-EQUIPMENT h BTSEP h RACK h FVSWRP h STOPTEST FVSWRP”
Applicability:Phase 2 and Phase 3.
Visibility level: 1.
Command Description:This command is used to stop a diagnostic previously started.
Long Names:NAME Address of the managed object
System Responses:Operation Completed
Test has been stopped. The System Responses will not be addressed to the MOT but to the object BTSEP.
Operation Failed
Test has not been stopped. This NACK-message can occur when the specified test is not running or in case of test which cannot be stopped.
Application Guidelines:None.
Result TEST:
name = TEST:<n>
testOutcome = inconclusive
mOts = It is the identifier of the hardware object under test.
testTermination = Cancel
executedPhases
phaseId = It represents the list of the executed test phases; the list is not shown for test in the waiting list (queued)....
.
failedPhases
phaseId = It represents the list of the failed test phase;
additional information is provided for each phase.phaseId =
....
skippedPhases
phaseId = It represents the list of the skipped phases;the list is not shown for test in the waiting list (queued).phaseId =
486DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805b1035
FVSWRP
Example of Command Execution:Stoptest FVSWRP:NAME=RACK:0/FVSWRP:0;
UNLOCK FVSWRP
Command Tree:“MANAGED-ELEMENT h BSS-EQUIPMENT h BTSEP h RACK h FVSWRP h UNLOCK FVSWRP”
Applicability:Phase 2 and Phase 3.
Visibility level: 1.
Command Description:This command changes the administrative state of FICOM_VSWR unit of the BTSE.
Long Names:NAME Address of the managed object
System Responses:Operation Completed
The specified change of administrative state has been perfomed:
JOB: 47
PC Time&Date: 16:33:19 03/23/2005
NE Time&Date: 16:31:13 09/15/2004
USER NAME: NSN_Ross
COMMAND: Unlock FVSWRP:NAME=RACK:0/FVSWRP:0;
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: Operation successful
administrativeState = Unlocked
END OF OUTPUT FOR JOB 47
CHANGED STATE EVENT REPORT:
This provides information about the administrative state, the operational state and the availability status every time a state change occurs:
UNLOCK FVSWRP NAME=RACK:0..7/FVSWRP:0..3;
DN0933412 Issue 01487
BTSplus mainline commands at the Flexi BSC product family
FVSWRP
Id:0900d805805b1035
JOB: 48
PC Time&Date: 16:33:19 03/23/2005
NE Time&Date: 16:31:13 09/15/2004
USER NAME: NSN_Ross
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: Operation successful
CHANGED STATE EVENT REPORT:
NAME = RACK:0/FVSWRP:0
Administrative State = UNLOCKED
Notification Identifier = 488
END OF OUTPUT FOR JOB 48
Operation Failed
The specified change of administrative state has not been performed.
Application Guidelines:None.
Example of Command Execution:Unlock FVSWRP:NAME=RACK:0/FVSWRP:0;
488DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805b1037
LAPDLE
LAPDLEThe LAPDLE object identifies the logical link used by the BTSplus mainline to commu-nicate with the Flexi BSCproduct family for operational and maintenance purposes.
CREATE LAPDLE
Command Tree:“MANAGED-ELEMENT h BSS-EQUIPMENT h BTSEP h LAPDLE h CREATE LAPDLE”
Applicability:Phase 2 and Phase 3.
Visibility level: 2.
Command Description:This command adds a LAPDLE object in the BTSE database.
Long Names:NAME Address of the managed object
LAPDCH lapdChannel
System Responses:Operation Completed
After command execution, a message of Changed Configuration Notification is dis-played. A further message indicates the result of the operation. An example of create command is the following:
JOB: 150
PC Time&Date: 12:02:21 03/23/2005
NE Time&Date: 13:03:56 09/15/2004
USER NAME: NSN_Ross
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: Operation successful
ChangedConfigurationNotification:
name = LAPDLE:2
ChangeInfo = created
END OF OUTPUT FOR JOB 150
CREATE LAPDLE NAME=LAPDLE:0..10 ,LAPDCH=;
DN0933412 Issue 01489
BTSplus mainline commands at the Flexi BSC product family
LAPDLE
Id:0900d805805b1037
JOB: 151
PC Time&Date: 12:02:31 03/23/2005
NE Time&Date: 13:04:06 09/15/2004
USER NAME: NSN_Ross
COMMAND: Create LAPDLE:NAME=LAPDLE:2,LAPDCH=BPORT0-1-SSL0_16KB;
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: Operation successful
END OF OUTPUT FOR JOB 151
Operation Failed
The specified Object has not been created. In addition to the general NACK causes, a specific NACK cause, which indicates that the command is inconsistent with the physical configuration, is possible. An example is the following:
JOB: 152
PC Time&Date: 12:02:31 03/23/2005
NE Time&Date: 13:04:06 09/15/2004
USER NAME: NSN_Ross
COMMAND: Create LAPDLE:NAME=LAPDLE:1,LAPDCH=BPORT0-1-SSL0_16KB;
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: OPERATION FAILED
MO already created (-159)
END OF OUTPUT FOR JOB 152
Application Guidelines:
• The LAPDLE object must be always created before the creation of the correspond-ing object on Flexi BSC product family side, otherwise the Abis Alignment procedure is going to fail
Example of Command Execution:Create LAPDLE:NAME=LAPDLE:0,LAPDCH=2-2-FULL_64KB;
490DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805b1037
LAPDLE
DELETE LAPDLE
Command Tree:“MANAGED-ELEMENT h BSS-EQUIPMENT h BTSEP h LAPDLE h DELETE LAPDLE”
Applicability:Phase 2 and Phase 3.
Visibility level: 2.
Command Description:This command deletes the LAPDLE from the BTSE data base.
Long Names:NAME Address of the managed object
System Responses:Operation Completed
After command execution, a message of Changed Configuration Notification is dis-played. A further message indicates the result of the operation. An example of delete command is the following:
JOB: 158
PC Time&Date: 12:03:55 03/23/2005
NE Time&Date: 13:05:22 09/15/2004
USER NAME: NSN_Ross
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: Operation successful
ChangedConfigurationNotification:
name = NAME=LAPDLE:2;
ChangeInfo = deleted
END OF OUTPUT FOR JOB 158
JOB: 159
PC Time&Date: 12:04:03 03/23/2005
NE Time&Date: 13:05:35 09/15/2004
DELETE LAPDLE NAME=LAPDLE:0..10;
DN0933412 Issue 01491
BTSplus mainline commands at the Flexi BSC product family
LAPDLE
Id:0900d805805b1037
USER NAME: NSN_Ross
COMMAND: Delete LAPDLE:NAME=LAPDLE:2;
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: Operation successful
END OF OUTPUT FOR JOB 159
Operation Failed
The specified Object has not been deleted. Additionally to the general NACK causes, a specific NACK cause, meaning that the command is inconsistent with physical configu-ration, is possible.
Application Guidelines:None.
Example of Command Execution:Delete LAPDLE:NAME=LAPDLE:0;
GET LAPDLE
Command Tree:“MANAGED-ELEMENT h BSS-EQUIPMENT h BTSEP h LAPDLE h GET LAPDLE”
Applicability:Phase 2 and Phase 3.
Visibility level: 0.
Command Description:This command displays the attributes of the LAPDLE unit of the BTSE.
Long Names:NAME Address of the managed object
REQATTL Required attribute list
ALS alarmStatus
AST administrativeState
AVS availabilityStatus
LAPDCH lapdChannel
OST operationalState
PRS proceduralStatus
RELFUNCOBJ relatedFuncObjects
STDBYST standbyStatus
GET LAPDLE NAME=LAPDLE:0..10 [,REQATTL=ALS, AST, AVS, LAPDCH, OST, PRS, RELFUNCOBJ, STDBYST];
492DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805b1037
LAPDLE
System Responses:Operation Completed
After command execution, a message of Changed Configuration Notification is dis-played. A further message indicates the result of the operation. An example of get command is the following:
JOB: 149
PC Time&Date: 12:02:04 03/23/2005
NE Time&Date: 13:03:39 09/15/2004
USER NAME: NSN_Ross
COMMAND: Get LAPDLE:NAME=LAPDLE:0;
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: Operation successful
alarmStatus = CLEARED
administrativeState = Unlocked
availabilityStatus = NULL
lapdChannel =
BPORT = BPORT0
TSL = 17
SSL = FULL_64KB
operationalState = ENABLED
proceduralStatus = NULL
relatedFuncObjects =
standbyStatus = ColdStandBy
END OF OUTPUT FOR JOB 149
Operation Failed
The GET command has not been successfully executed. A general NACK will indicate possible errors or a specific NACK strictly related to the single command is possible.
Application Guidelines:
• The value for the attribute relatedFuncObjects in LMT Evolution Phase 2 is "not con-figured"
Example of Command Execution:Get LAPDLE:NAME=RACK:0,REQATTL=ALS&AST&AVS&LAPCH&
RELFUNCOBJ&OST&PRS&STBYST;
DN0933412 Issue 01493
BTSplus mainline commands at the Flexi BSC product family
RACK
Id:0900d805805b103b
RACKThe RACK object models the rack of the BTSplus mainline family.
The BS240/1 consists of a base rack with up to 8 TRXs. Optionally it can be connected to two extension racks to reach up to 24 TRX. The BS240XL consists of a base rack with up to 12 TRXs. Optionally it can be connected to an extension rack to reach up to 24 TRXs.
CREATE RACK
Command Tree:“MANAGED-ELEMENT h BSS-EQUIPMENT h BTSEP h RACK h CREATE RACK”
Applicability:Phase 2 and Phase 3.
Visibility level: 2.
Command Description:This command adds the object RACK together with its attributes to the BTSE data base.
Long Names:NAME Address of the managed object
TYPRACK typeOfBtse
System Responses:Operation Completed
After command execution, a message of Changed Configuration Notification is dis-played. A further message indicates the result of the operation. An example of create command is the following:
JOB: 230
PC Time&Date: 14:50:07 03/23/2005
NE Time&Date: 00:17:45 09/15/2004
USER NAME: NSN_ Eberhard
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: Operation successful
ChangedConfigurationNotification:
name = RACK:1
CREATE RACK NAME=RACK:0..7 ,TYPRACK=;
494DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805b103b
RACK
ChangeInfo = created
END OF OUTPUT FOR JOB 230
JOB: 231
PC Time&Date: 14:50:08 03/23/2005
NE Time&Date: 00:17:46 09/15/2004
USER NAME: NSN_ Eberhard
COMMAND: Create RACK:NAME=RACK:1;
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT Operation successful
END OF OUTPUT FOR JOB 231
Operation Failed
The specified Object has not been created. In addition to the general NACK causes, a specific NACK cause, which indicates that the command is inconsistent with the physical configuration, is possible. An example is the following:
JOB: 232
PC Time&Date: 14:50:08 03/23/2005
NE Time&Date: 00:17:46 09/15/2004
USER NAME: NSN_ Eberhard
COMMAND: Create RACK:NAME=RACK:1;
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: OPERATION FAILED
MO already created (-159)
END OF OUTPUT FOR JOB 232
Application Guidelines:
• RACK:0 can never be created. It had to be set, with Set RACK as first command
• If an other rack type for RACK:0 is create, you had to format the flash and had to make a power on; e.g. if you have at coba in DB (rack0) racktype BS242 (pico) and want a racktype 240XL at coba. You had to format the flash and had to make a power on at coba. With set rack or delete db this is not possible. (here you have dif-ferent SW)
DN0933412 Issue 01495
BTSplus mainline commands at the Flexi BSC product family
RACK
Id:0900d805805b103b
( ! ) The Command Create RACK is no longer supported for BS240SWB, BS241SWB and BS240XLSWB
Example of Command Execution:Create RACK:NAME=RACK:1,TYPRACK=BS240;
DELETE RACK
Command Tree:“MANAGED-ELEMENT h BSS-EQUIPMENT h BTSEP h RACK h DELETE RACK”
Applicability:Phase 2 and Phase 3.
Visibility level: 2.
Command Description:This command deletes the object RACK together with its attributes from the BTSE data base.
Long Names:NAME Address of the managed object
System Responses:Operation Completed
After command execution, a message of Changed Configuration Notification is dis-played. A further message indicates the result of the operation. An example of delete command is the following:
JOB: 233
PC Time&Date: 14:50:08 03/23/2005
NE Time&Date: 00:17:46 09/15/2004
USER NAME: NSN_ Eberhard
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: Operation successful
ChangedConfigurationNotification:
name = RACK:1
ChangeInfo = deleted
DELETE RACK NAME=RACK:0..7;
496DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805b103b
RACK
END OF OUTPUT FOR JOB 233
JOB: 234
PC Time&Date: 14:50:08 03/23/2005
NE Time&Date: 00:17:46 09/15/2004
USER NAME: NSN_ Eberhard
COMMAND: Delete RACK:NAME=RACK:1;
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: Operation successful
END OF OUTPUT FOR JOB 234
Operation Failed
The specified Object has not been deleted. Additionally to the general NACK causes, a specific NACK cause, meaning that the command is inconsistent with physical configu-ration, is possible.
Application Guidelines:
• RACK:0 can never be deleted by DELETE command only using FORMAT FLASH and power on
Example of Command Execution:
• Delete RACK:NAME=RACK:1
• It can be deleted with format flash and power on
GET RACK
Command Tree:“MANAGED-ELEMENT h BSS-EQUIPMENT h BTSEP h RACK h GET RACK”
Applicability:Phase 2 and Phase 3.
Visibility level: 0.
Command Description:This command displays the attributes related to the specified RACK.
Long Names:NAME Address of the managed object
REQATTL Required attribute list
ALS alarmStatus
GET RACK NAME=RACK:0..7 [,REQATTL=ALS, AST, AVS, OST, PRS, RELFUNCOBJ, TYPRACK];
DN0933412 Issue 01497
BTSplus mainline commands at the Flexi BSC product family
RACK
Id:0900d805805b103b
AST administrativeState
AVS availabilityStatus
OST operationalState
PRS proceduralStatus
RELFUNCOBJ relatedFuncObjects
TYPRACK typeOfBtse
System Responses:Operation Completed
After command execution, a message of Changed Configuration Notification is dis-played. A further message indicates the result of the operation. An example of get command is the following:
JOB: 5
PC Time&Date: 12:03:10 03/23/2005
NE Time&Date: 12:01:00 09/15/2004
USER NAME: NSN_ Eberhard
COMMAND: Get RACK:NAME=RACK:0;
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: Operation successful
alarmStatus = MINOR
administrativeState = Unlocked
availabilityStatus = NULL
operationalState = ENABLED
proceduralStatus = NULL
relatedFuncObjects =
typeOfBtse = BS240XL
END OF OUTPUT FOR JOB 5
Operation Failed
The GET command has not been successfully executed. A general NACK will indicate possible errors or a specific NACK strictly related to the single command is possible.
Application Guidelines:None.
Example of Command Execution:Get RACK:NAME=RACK:0,REQATTL=ALS&AST&AVS&RELFUNCOBJ&OST&
498DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805b103b
RACK
PRS&TYPRACK;
LOCK RACK
Command Tree:“MANAGED-ELEMENT h BSS-EQUIPMENT h BTSEP h RACK h LOCK RACK”
Applicability:Phase 2 and Phase 3.
Visibility level: 1.
Command Description:This command changes the administrative state of the object RACK.
Long Names:NAME Address of the managed object
System Responses:Operation Completed
The specified change of administrative state has been perfomed:
JOB: 235
PC Time&Date: 14:50:08 03/23/2005
NE Time&Date: 00:17:46 09/15/2004
USER NAME: NSN_ Eberhard
COMMAND: Lock RACK:NAME=RACK:1;
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: Operation successful
administrativeState = Locked
END OF OUTPUT FOR JOB 235
CHANGED STATE EVENT REPORT:
This provides information about the administrative state, the operational state and the availability status every time a state change occurs:
JOB: 236
LOCK RACK NAME=RACK:0..7;
DN0933412 Issue 01499
BTSplus mainline commands at the Flexi BSC product family
RACK
Id:0900d805805b103b
PC Time&Date: 14:50:08 03/23/2005
NE Time&Date: 00:17:46 09/15/2004
USER NAME: NSN_ Eberhard
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: Operation successful
CHANGED STATE EVENT REPORT:
NAME = RACK:1
Administrative State = LOCKED
Notification Identifier = 147
END OF OUTPUT FOR JOB 236
Operation Failed
The specified change of administrative state has not been performed.
Application Guidelines:
• RACK:0 can never be locked
Example of Command Execution:Lock RACK:NAME=RACK:1;
SET RACK
Command Tree:“MANAGED-ELEMENT h BSS-EQUIPMENT h BTSEP h RACK h SET RACK”
Applicability:Phase 2.
Visibility level: 2.
Command Description:This command is used to set the attributes of the specified RACK.
Long Names:NAME Address of the managed object
TYPRACK typeOfBtse
System Responses:Operation Completed
SET RACK NAME=RACK:0..7 [,TYPRACK=];
500DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805b103b
RACK
After command execution, a message of Changed Attribute Event Report is displayed. A further message indicates the result of the operation. An example of set command is the following:
JOB: 176
PC Time&Date: 12:05:36 03/23/2005
NE Time&Date: 13:07:12 09/15/2004
USER NAME: NSN_ Eberhard
COMMAND: Set RACK:NAME=RACK:0;
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: Operation successful
END OF OUTPUT FOR JOB 176
Operation Failed
The specified attributes have not been set. In addition to the general NACK causes, a specific NACK cause, which indicates that the command is inconsistent with the physical configuration, is possible.
Application Guidelines:
• The attribute TYPRACK must be set. Otherwise the NetAct system is not able to identify the correct BTSplus mainline
• RACK:0 has to be set, otherwise no object can be created
• RACK:0 cannot be changed, it has to be deleted by delete BTSEPDBFILE (e.g., if you have a coba with rack BS240 and want a racktype 240XL you have to delete dbfile (delete DB). Here you have the same SW)
( ! ) The Command Set RACK is no longer supported for BS240SWB, BS241SWB and BS240XLSWB
Example of Command Execution:Set RACK:NAME=RACK:0,TYPRACK=BS240;
UNLOCK RACK
Command Tree:“MANAGED-ELEMENT h BSS-EQUIPMENT h BTSEP h RACK h UNLOCK RACK”
Applicability:Phase 2 and Phase 3.
Visibility level: 1.
UNLOCK RACK NAME=RACK:0..7;
DN0933412 Issue 01501
BTSplus mainline commands at the Flexi BSC product family
RACK
Id:0900d805805b103b
Command Description:This command changes the administrative state of the object RACK.
Long Names:NAME Address of the managed object
System Responses:Operation Completed
The specified change of administrative state has been perfomed:
JOB: 237
PC Time&Date: 14:50:08 03/23/2005
NE Time&Date: 00:17:46 09/15/2004
USER NAME: NSN_ Eberhard
COMMAND: Unlock RACK:NAME=RACK:1;
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: Operation successful
administrativeState = Unlocked
END OF OUTPUT FOR JOB 237
CHANGED STATE EVENT REPORT:
This provides information about the administrative state, the operational state and the availability status every time a state change occurs:
JOB: 238
PC Time&Date: 14:50:09 03/23/2005
NE Time&Date: 00:17:47 09/15/2004
USER NAME: NSN_ Eberhard
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: Operation successful
CHANGED STATE EVENT REPORT:
NAME = RACK:1
502DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805b103b
RACK
Administrative State = UNLOCKED
Notification Identifier = 321
END OF OUTPUT FOR JOB 237
Operation Failed
The specified change of administrative state has not been performed.
Application Guidelines:None.
Example of Command Execution:Unlock RACK:NAME=RACK:0;
DN0933412 Issue 01503
BTSplus mainline commands at the Flexi BSC product family
REMINV
Id:0900d805805b103d
REMINVThe REMINV object manages the BTSplus mainline local Inventory Data Table in case of installation of new hardware objects or replacement of already existing hardware objects.
DNLIDFD REMINV
Command Tree:“MANAGED-ELEMENT h BSS-EQUIPMENT h BTSEP h REMINV h DNLIDFD REMINV”
Applicability:Phase 2 and Phase 3.
Visibility level: 1.
Command Description:This command executes the download of the NOB file (containing nob_RIUs of the IDF) from the LMT hard disk to the BTSE flash EPROMs.
Long Names:NAME Address of the managed object
SRCDIR sourceDir
System Responses:Operation Completed
After command execution, a further message indicates the result of the operation. An example of dnlidfd command is the following:
JOB: 155
PC Time&Date: 12:03:15 03/23/2005
NE Time&date: 0:00:00 00/00/0
USER NAME: NSN
COMMAND: Dnlidfd REMINV:NAME=REMINV:0,SRCDIR="C:\labuser\BsPlus";
SW RELEASE: N.A.
COMMAND RESULT: Operation successful
END OF OUTPUT FOR JOB 155
Operation Failed
None.
DNLIDFD REMINV NAME=REMINV:0..0 [,SRCDIR=];
504DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805b103d
REMINV
Application Guidelines:
• This file is to be created previously using the "IDF-Editor". The name for BTSE is fix "BTS_NRIU"
Example of Command Execution:Dnlidfd REMINV:SRCDIR="C:\Programme\IdfEditor|\dnload";
UPLLIDF REMINV
Command Tree:“MANAGED-ELEMENT h BSS-EQUIPMENT h BTSEP h REMINV h UPLLIDF REMINV”
Applicability:Phase 1 and Phase 2 and Phase 3.
Visibility level: 1.
Command Description:This command executes the uploading of the IDF (Inventory Data File) from the BTSE flash EPROMs to the LMT hard disk.
Long Names:NAME Address of the managed object
DESTDIR destinationDir
FILE file
OVERWRITE Overwrite
System Responses:Operation Completed
After command execution, a further message indicates the result of the operation. An example of upllidf command is the following:
JOB: 156
PC Time&Date: 12:03:18 03/23/2005
NE Time&date: 0:00:00 00/00/0
USER NAME: NSN
COMMAND: Upllidf REMINV:NAME=REMINV:0,OVERWRITE=YES;
SW RELEASE: N.A.
COMMAND RESULT: Operation successful
Uploading File: BTSE.IDT
UPLLIDF REMINV NAME=REMINV:0..0 [,DESTDIR=] [,FILE=] ,OVERWRITE=;
DN0933412 Issue 01505
BTSplus mainline commands at the Flexi BSC product family
REMINV
Id:0900d805805b103d
To: BTSE.IDT
On Directory: ..\Idf\Upload
END OF OUTPUT FOR JOB 156
JOB: 157
PC Time&Date: 12:03:19 03/23/2005
NE Time&date: 00:00:00 00/00/0
USER NAME: NSN
COMMAND: Upllidf REMINV:NAME=REMINV:0,OVERWRITE=YES;
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: Operation successful
Upload End: File BTSE.IDT Transfer Completed
END OF OUTPUT FOR JOB 157
Operation Failed
None.
Application Guidelines:
• The offline tool "IDF-Editor" is used to display and modify the uploaded IDT. It is used also for converting the IDT into an IDF or to extract the NOB file
• The default value of FILE is BTSE.IDT
Example of Command Execution:Uplidfd REMINV:DESTDIR="c:\rem_inve",FILE="bts_inv.idt",OVERWRITE=YES;
506DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805b103f
SOFTWARE-MANAGEMENT
SOFTWARE-MANAGEMENTThe SOFTWARE-MANAGEMENT object supports software management functions and manages the BTSplus mainline file system.
DNLALLEXE SOFTWARE-MANAGEMENT
Command Tree:“MANAGED-ELEMENT h SOFTWARE-MANAGEMENT h DNLALLEXE SOFTWARE-MANAGEMENT”
Applicability:Phase 1 and Phase 2 and Phase 3.
Visibility level: 0.
Command Description:This command executes the software downloading of the BTSplus mainline SW from the LMT Evolution PC hard disk to the COBA board.
Long Names:IDSOFTWARE-MANAGEMENT Address of the managed object
SRCPATH srcpath
OVERWRITE Overwrite
System Responses:Operation Completed
Download START. After command execution, a further message indicates the result of the operation. An example of dnlallexe command is the following:
JOB: 175
PC Time&Date: 12:05:17 03/23/2005
NE Time&date: 0:00:00 00/00/0
USER NAME: NSN
COMMAND: DNLALLEXE:SRCPATH="C\test\hs031785\HS011722.SWL",OVER-WRITE=YES;
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: Operation successful
Downloading File: HS011726.SWL:01-04-17-01-26-51_05-02-23
DNLALLEXE SOFTWARE-MANAGE-MENT
SRCPATH= ,OVERWRITE=;
DN0933412 Issue 01507
BTSplus mainline commands at the Flexi BSC product family
SOFTWARE-MANAGEMENT
Id:0900d805805b103f
Version: 02-08-01-01-00-27_04-11-19
END OF OUTPUT FOR JOB 175
Operation Failed
= (invalid SW-Version, defective SW)
Application Guidelines:
• If the incorrect SW version is given, the system will reject the command
• The SWLoadSafety will not be overwritten
• In Phase 1 this command is followed by a forced download
• In Phase 2 the command is followed by a forced download if the SwVersion is iden-tical to the currentSWLoad
Example of Command Execution:Dnlallexe:SRCPATH="c:\path\HS011722.SWL", OVERWRITE= YES;
UPLBTSLOG SOFTWARE-MANAGEMENT
Command Tree:“MANAGED-ELEMENT h SOFTWARE-MANAGEMENT h UPLBTSLOG SOFTWARE-MANAGEMENT”
Applicability:Phase 2 and Phase 3.
Visibility level: 2.
Command Description:The usage of this command is reserved to the R&D and should be used only under R&D request.
Long Names:IDSOFTWARE-MANAGEMENT Address of the managed object
FILETYPE FileType
DESTDIR destinationDir
FILE file
ENTRIES entries
OVERWRITE Overwrite
System Responses:Operation Completed
After command execution, a further message indicates the result of the operation. An example of uplbtslog command is the following:
UPLBTSLOG SOFTWARE-MANAGE-MENT
FILETYPE= ,DESTDIR= ,FILE= [,ENTRIES=] ,OVER-WRITE=;
508DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805b103f
SOFTWARE-MANAGEMENT
JOB: 177
PC Time&Date: 12:06:04 03/23/2005
NE Time&date: 0:00:00 00/00/0
USER NAME: NSN
COMMAND: UPLBTSLOG:DESTDIR="D:\DocumentBtsplus",FILE="240xl",OVER-WRITE=YES;
SW RELEASE: N.A.
COMMAND RESULT: Operation successful
Uploading File: 240xl
To: 240xl
On Directory: D:\DocumentBtsplus
END OF OUTPUT FOR JOB 177
JOB: 178
PC Time&Date: 12:06:25 03/23/2005
NE Time&date: 00:00:00 00/00/0
USER NAME: NSN
COMMAND: UPLBTSLOG:DESTDIR="D:\DocumentBtsplus",FILE="240xl",OVER-WRITE=YES;
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: Operation successful
Uploading File 240xl:
100 packets received
END OF OUTPUT FOR JOB 178
Operation Failed
None.
Application Guidelines:None.
DN0933412 Issue 01509
BTSplus mainline commands at the Flexi BSC product family
SOFTWARE-MANAGEMENT
Id:0900d805805b103f
Example of Command Execution:The execution of this command is reserved to the R&D and should be executed only under R&D request.
510DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805b1041
SYNCBTSE
SYNCBTSEThe SYNCBTSE object holds parameters that the user can configure. The object indi-cates the synchronization state and accuracy. This is sufficient to maintain configuration and states, so no further modeling of the external GPS equipment is necessary.
GET SYNCBTSE
Command Tree:“MANAGED-ELEMENT h BSS-EQUIPMENT h BTSEP h SYNCBTSE h GET SYNCBTSE”
Applicability:Phase 2 and Phase 3.
Visibility level: 0.
Command Description:This command displays the attributes of the SYNCBTSE of the BTSE.
Long Names:NAME Address of the managed object
REQATTL Required attribute list
ALS alarmStatus
AST administrativeState
AVS availabilityStatus
CLKACC clockAccuracy
MPHERR maxPhaseError(microsec)
MRSYNCT maxResyncTime(min)
OST operationalState
PRS proceduralStatus
RELFUNCOBJ relatedFuncObjects
SBPRT syncBport
SYNCSRC syncSource
SYNCSTAT syncState
System Responses:Operation Completed
After command execution, a message of Changed Configuration Notification is dis-played. A further message indicates the result of the operation. An example of get command is the following:
GET SYNCBTSE NAME=SYNCBTSE:0..0 [,REQATTL=ALS, AST, AVS, CLKACC, MPHERR, MRSYNCT, OST, PRS, RELFUN-COBJ, SBPRT, SYNCSRC, SYNCSTAT];
DN0933412 Issue 01511
BTSplus mainline commands at the Flexi BSC product family
SYNCBTSE
Id:0900d805805b1041
JOB: 7
PC Time&Date: 16:24:35 03/23/2005
NE Time&Date: 16:22:29 09/15/2004
USER NAME: NSN
COMMAND: Get SYNCBTSE:NAME=SYNCBTSE:0;
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: Operation successful
alarmStatus = CLEARED
administrativeState = Unlocked
availabilityStatus = NULL
clockAccuracy = high
maxPhaseError(microsec) = 1.5
maxResyncTime(min) = 180
operationalState = ENABLED
proceduralStatus = NULL
relatedFuncObjects =
syncSource = abis
syncState = abis
END OF OUTPUT FOR JOB 7
Operation Failed
The GET command has not been successfully executed. A general NACK will indicate possible errors or a specific NACK strictly related to the single command is possible.
Application Guidelines:None.
Example of Command Execution:Get SYNCBTSE:NAME=SYNCBTSE:0,REQATTL=ALS&AST&AVS&BCPBL&
CLKACC&MPHERR&MRSYNCT&OST&PRS&RELFUNCOBJ&SYNCSRC&
SYNCSTAT;
GETTEST SYNCBTSE
Command Tree:“MANAGED-ELEMENT h BSS-EQUIPMENT h BTSEP h SYNCBTSE h GETTEST SYNCBTSE”
GETTEST SYNCBTSE NAME=SYNCBTSE:0..0;
512DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805b1041
SYNCBTSE
Applicability:Phase 2 and Phase 3.
Visibility level: 0.
Command Description:This command displays the attributes of the SYNCBTSE test.
Long Names:NAME Address of the managed object
REQATTL Required attribute list
System Responses:Operation Completed
After command execution, a message of Changed Configuration Notification is dis-played. A further message indicates the result of the operation. An example of gettest command is the following:
JOB: 300
PC Time&Date: 14:50:17 03/23/2005
NE Time&Date: 00:17:55 09/15/2004
USER NAME: NSN
COMMAND: Gettest SYNCBTSE:NAME=SYNCBTSE:0;
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: Operation successful
MOT = SYNCBTSE:0
testMonitor =
phaseId = PreliminaryTestsSYNCBTSE
phaseStatus = Running
phaseId = CheckAlarmStatusSYNCBTSE
phaseStatus = Waiting
phaseId = EndTestSYNCBTSE
phaseStatus = Waiting
testOutcome = INCONCLUSIVE
testState = INITIALIZING
END OF OUTPUT FOR JOB 300
Operation Failed
The GET command has not been successfully executed. A general NACK will indicate possible errors or a specific NACK strictly related to the single command is possible.
DN0933412 Issue 01513
BTSplus mainline commands at the Flexi BSC product family
SYNCBTSE
Id:0900d805805b1041
Application Guidelines:None.
Example of Command Execution:Gettest SYNCBTSE:NAME=SYNCBTSE:0,REQATTL=MORT&TESTMON&
TESTOUT&TESTST;
LOCK SYNCBTSE
Command Tree:“MANAGED-ELEMENT h BSS-EQUIPMENT h BTSEP h SYNCBTSE h LOCK SYNCBTSE”
Applicability:Phase 2 and Phase 3.
Visibility level: 1.
Command Description:This command changes the administrative state of the SYNCBTSE of the BTSE.
Long Names:NAME Address of the managed object
System Responses:Operation Completed
The specified change of administrative state has been perfomed:
testMonitor it is a list of all test phases related to the selected object; for each phase the related phaseStatus is provided (Passed, Failed, Running or Waiting).
phaseId =
phaseStatus =
phaseId =
phaseStatus =
...
...
testOutcome It represents the test result: it can be Inconclusive (if the phases already executed were successful) or Fail (if at least one of the executed phases failed).
testState = Testing It can assume one of the following values: not_initialized, idle, initializing, sus-pended, testing, terminating and dis-abled.
LOCK SYNCBTSE NAME=SYNCBTSE:0..0;
514DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805b1041
SYNCBTSE
JOB: 8
PC Time&Date: 16:24:42 03/23/2005
NE Time&Date: 16:22:36 09/15/2004
USER NAME: NSN
COMMAND: Lock SYNCBTSE:NAME=SYNCBTSE:0;
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: Operation successful
administrativeState = Locked
END OF OUTPUT FOR JOB 8
CHANGED STATE EVENT REPORT:
This provides information about the administrative state, the operational state and the availability status every time a state change occurs:
JOB: 9
PC Time&Date: 16:24:42 03/23/2005
NE Time&Date: 16:22:36 09/15/2004
USER NAME: NSN
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: Operation successful
CHANGED STATE EVENT REPORT:
NAME = SYNCBTSE:0
Administrative State = LOCKED
Notification Identifier = 461
END OF OUTPUT FOR JOB 9
Operation Failed
The specified change of administrative state has not been performed (e.g. the object is redundant and its spare copy is disabled or already locked, a subordinate resource cannot go into disabled state with "dependency" availability status).
DN0933412 Issue 01515
BTSplus mainline commands at the Flexi BSC product family
SYNCBTSE
Id:0900d805805b1041
Application Guidelines:Lock of SYNCBTSE (= SET administrativeState to â??locked) is rejected if syncSource = ext_1pps_only
Example of Command Execution:Lock SYNCBTSE:NAME=SYNCBTSE:0;
PERFTEST SYNCBTSE
Command Tree:“MANAGED-ELEMENT h BSS-EQUIPMENT h BTSEP h SYNCBTSE h PERFTEST SYNCBTSE”
Applicability:Phase 2 and Phase 3.
Visibility level: 1.
Command Description:This command is used to start an asynchronous test in SYNCBTSE.
Long Names:NAME Address of the managed object
System Responses:Operation Completed
Test configuration has been set and the specified test has been started. The System response will not be addressed to the MOT but to the object BTSE.
JOB: 240
PC Time&Date: 14:50:09 03/23/2005
NE Time&Date: 00:17:47 09/15/2004
USER NAME: NSN
COMMAND: Perftest SYNCBTSE:NAME=SYNCBTSE:0;
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: Operation successful
MOT = SYNCBTSE
tO = BTSETEST:1
END OF OUTPUT FOR JOB 240
PERFTEST SYNCBTSE NAME=SYNCBTSE:0..0;
516DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805b1041
SYNCBTSE
JOB: 241
PC Time&Date: 14:50:09 03/23/2005
NE Time&Date: 00:17:47 09/15/2004
USER NAME: NSN
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: Operation successful
ChangedConfigurationNotification:
name = BTSETEST:1
ChangeInfo = created
END OF OUTPUT FOR JOB 241
JOB: 242
PC Time&Date: 14:50:12 03/23/2005
NE Time&Date: 00:17:51 09/15/2004
USER NAME: NSN
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: Operation successful
CHANGED STATE EVENT REPORT:
NAME = SYNCBTSE:0
Operational State = ENABLED
Availability Status = NULL_value
Notification Identifier = 143
END OF OUTPUT FOR JOB 242
JOB: 243
PC Time&Date: 14:50:12 03/23/2005
NE Time&Date: 00:17:51 09/15/2004
USER NAME: NSN
DN0933412 Issue 01517
BTSplus mainline commands at the Flexi BSC product family
SYNCBTSE
Id:0900d805805b1041
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: Operation successful
Test Report:
name = BTSETEST:1
testOutcome = PASSED
testTermination = Normal
MOT = SYNCBTSE:0
executedPhases =
PreliminaryTestsSYNCBTSE
CheckAlarmStatusSYNCBTSE
EndTestSYNCBTSE
END OF OUTPUT FOR JOB 243
JOB: 244
PC Time&Date: 14:50:09 03/23/2005
NE Time&Date: 00:17:47 09/15/2004
USER NAME: NSN
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: Operation successful
ChangedConfigurationNotification:
name = BTSETEST:1
ChangeInfo = deleted
END OF OUTPUT FOR JOB 244
The test results will be displayed at the end of the test phases.
Result TEST:
name = TEST:<n>
testOutcome = This field represents the test result; one of the fol-lowing values can be displayed:
Pass all the test phases are successfully performed.
518DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805b1041
SYNCBTSE
Operation Failed
This NACK-message occurs in the following cases: Message cannot be performed, test not supported, capacity restrictions, physical configuration cannot be performed, object not locked.
Application Guidelines:None.
Example of Command Execution:Perftest SYNCBTSE:NAME=SYNCBTSE:0;
SET SYNCBTSE
Inconclusive the test is aborted by the system or the test is terminated by the opera-tor.
Fail if at least one of the executed phases fail.
mOts = It is the identifier of the hardware object under test.
testTermination = It specifies how the test is terminated, it can assume the following values:
Normal all the test phases are performed.
Abort the test is aborted by system.
Cancel the test is terminated by operator.
executedPhases
phaseId = It represents the list of the executed test phases (in case of successful test result, all the test phases will be listed).
additionalWords =
....
failedPhases
phaseId = It represents the list of the failed test phase; addi-tional information is provided for each phase.phaseId =
....
skippedPhases
phaseId = It represents the list of the skipped phases; they are displayed only for test stopped during it execution.phaseId =
....
poprosedRepair Action =
A list of most probable fail probable causes is shown (max four messages)
SET SYNCBTSE NAME=SYNCBTSE:0..0 [,MPHERR=] [,MRSYNCT=] [,SYNCSRC=];
DN0933412 Issue 01519
BTSplus mainline commands at the Flexi BSC product family
SYNCBTSE
Id:0900d805805b1041
Command Tree:“MANAGED-ELEMENT h BSS-EQUIPMENT h BTSEP h SYNCBTSE h SET SYNCBTSE”
Applicability:Phase 2 and Phase 3.
Visibility level: 2.
Command Description:This command sets the attributes for the mapping of the SYNCBTSE.
Long Names:NAME Address of the managed object
MPHERR maxPhaseError(microsec)
MRSYNCT maxResyncTime(min)
SYNCSRC syncSource
System Responses:Operation Completed
The specified attribute has been set. In addition, a Changed Attribute Event Report indi-cates that the command has been successfully executed:
JOB: 20
PC Time&Date: 12:06:33 03/23/2005
NE Time&Date: 12:04:23 09/15/2004
USER NAME: NSN
COMMAND: Set SYNCBTSE:NAME=SYNCBTSE:0,MPHERR=1.5,SYNC-SRC=abis;
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: Operation successful
maxPhaseError(microsec) = 1.5
syncSource = abis
END OF OUTPUT FOR JOB 20
Operation Failed
The specified Object has not been created. In addition to the general NACK causes, a specific NACK cause, which indicates that the command is inconsistent with the physical configuration, is possible.
520DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805b1041
SYNCBTSE
Application Guidelines:
• Setting syncSource to "ext_1pps_only" is rejected for COBA different than COBA4P12 version 2 or CESCOBA
• Setting syncSource to "ext_1pps_only" is rejected if administrativeState of SYNCBTSE is locked
Example of Command Execution:Set SYNCBTSE:NAME=SYNCBTSE:0,MPHERR=1.5,MRSYNCT=200,
SYNCSRC=extGPS;
STOPTEST SYNCBTSE
Command Tree:“MANAGED-ELEMENT h BSS-EQUIPMENT h BTSEP h SYNCBTSE h STOPTEST SYNCBTSE”
Applicability:Phase 2 and Phase 3.
Visibility level: 1.
Command Description:This command is used to stop a diagnostic previously started.
Long Names:NAME Address of the managed object
System Responses:Operation Completed
Test has been stopped. The System Responses will not be addressed to the MOT but to the object BTSEP.
STOPTEST SYNCBTSE NAME=SYNCBTSE:0..0;
Result TEST:
name = TEST:<n>
testOutcome = inconclusive
mOts = It is the identifier of the hardware object under test.
testTermination = Cancel
executedPhases
phaseId = It represents the list of the executed test phases; the list is not shown for test in the waiting list (queued)....
.
failedPhases
DN0933412 Issue 01521
BTSplus mainline commands at the Flexi BSC product family
SYNCBTSE
Id:0900d805805b1041
Operation Failed
Test has not been stopped. This NACK-message can occur when the specified test is not running or in case of test which cannot be stopped.
Application Guidelines:None.
Example of Command Execution:Stoptest SYNCBTSE:NAME=SYNCBTSE:0;
UNLOCK SYNCBTSE
Command Tree:“MANAGED-ELEMENT h BSS-EQUIPMENT h BTSEP h SYNCBTSE h UNLOCK SYNCBTSE”
Applicability:Phase 2 and Phase 3.
Visibility level: 1.
Command Description:This command changes the administrative state of the SYNCBTSE to the BTSE.
Long Names:NAME Address of the managed object
System Responses:Operation Completed
The specified change of administrative state has been perfomed:
JOB: 10
PC Time&Date: 16:24:48 03/23/2005
NE Time&Date: 16:22:42 09/15/2004
USER NAME: NSN
phaseId = It represents the list of the failed test phase;
additional information is provided for each phase.phaseId =
....
skippedPhases
phaseId = It represents the list of the skipped phases;the list is not shown for test in the waiting list (queued).phaseId =
UNLOCK SYNCBTSE NAME=SYNCBTSE:0..0;
522DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805b1041
SYNCBTSE
COMMAND: Unlock SYNCBTSE:NAME=SYNCBTSE:0;
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: Operation successful
administrativeState = Unlocked
END OF OUTPUT FOR JOB 10
CHANGED STATE EVENT REPORT:
This provides information about the administrative state, the operational state and the availability status every time a state change occurs:
JOB: 11
PC Time&Date: 16:24:48 03/23/2005
NE Time&Date: 16:22:42 09/15/2004
USER NAME: NSN
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: Operation successful
CHANGED STATE EVENT REPORT:
NAME = SYNCBTSE:0
Administrative State = UNLOCKED
Notification Identifier = 462
END OF OUTPUT FOR JOB 11
Operation Failed
The specified change of administrative state has not been performed.
Application Guidelines:None.
Example of Command Execution:Unlock SYNCBTSE:NAME=SYNCBTSE:0;
DN0933412 Issue 01523
BTSplus mainline commands at the Flexi BSC product family
TMA
Id:0900d805805b1043
TMAThe TMA object models the tower mounted amplifier.
CREATE TMA
Command Tree:“MANAGED-ELEMENT h BSS-EQUIPMENT h BTSEP h RACK h TMA h CREATE TMA”
Applicability:Phase 2 and Phase 3.
Visibility level: 2.
Command Description:This command adds the TMA (Tower Mounted Amplifier) to the BTSE data base.
Long Names:NAME Address of the managed object
System Responses:Operation Completed
After command execution, a message of Changed Configuration Notification is dis-played. A further message indicates the result of the operation. An example of create command is the following:
JOB: 5
PC Time&Date: 16:24:23 03/23/2005
NE Time&Date: 16:22:17 09/15/2004
USER NAME: NSN
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: Operation successful
ChangedConfigurationNotification:
name = RACK:0/TMA:0
ChangeInfo = created
END OF OUTPUT FOR JOB 5
JOB: 6
CREATE TMA NAME=RACK:0..7/TMA:0..15;
524DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805b1043
TMA
PC Time&Date: 16:24:23 03/23/2005
NE Time&Date: 16:22:17 09/15/2004
USER NAME: NSN
COMMAND: Create TMA:NAME=RACK:0/TMA:0;
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: Operation successful
END OF OUTPUT FOR JOB 6
Operation Failed
The specified Object has not been created. In addition to the general NACK causes, a specific NACK cause, which indicates that the command is inconsistent with the physical configuration, is possible. An example is the following:
JOB: 80
PC Time&Date: 16:37:54 03/23/2005
NE Time&Date: 16:35:47 09/15/2004
USER NAME: NSN
COMMAND: Create TMA:NAME=RACK:0/TMA:0;
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: OPERATION FAILED
Object instance unknown (-9)
END OF OUTPUT FOR JOB 80
Application Guidelines:
• The DUAMCO/DIAMCO amplifier has two different operation modes which can be selected by e.g. DIP switches. In case a TMA is used the DUAMCO/DIAMCO must be configured in the MUCO mode. If no TMA is used the DUAMCO/DIAMCO must be configured in the AMCO mode
• As in the MUCO mode the gain is reduced to about 0 dB, the exact gain of the DUAMCO/DIAMCO to compensate the cable losses must be adjusted once during the installation of the BTSplus mainline by the service personnel
Example of Command Execution:Create TMA:NAME=RACK:0/TMA:0;
DN0933412 Issue 01525
BTSplus mainline commands at the Flexi BSC product family
TMA
Id:0900d805805b1043
DELETE TMA
Command Tree:“MANAGED-ELEMENT h BSS-EQUIPMENT h BTSEP h RACK h TMA h DELETE TMA”
Applicability:Phase 2 and Phase 3.
Visibility level: 2.
Command Description:This command deletes the TMA (Tower Mounted Amplifier) to the BTSE data base.
Long Names:NAME Address of the managed object
System Responses:Operation Completed
After command execution, a message of Changed Configuration Notification is dis-played. A further message indicates the result of the operation. An example of delete command is the following:
JOB: 14
PC Time&Date: 16:24:59 03/23/2005
NE Time&Date: 16:22:53 09/15/2004
USER NAME: NSN
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: Operation successful
ChangedConfigurationNotification:
name = RACK:0/TMA:0
ChangeInfo = deleted
END OF OUTPUT FOR JOB 14
JOB: 15
PC Time&Date: 16:24:59 03/23/2005
NE Time&Date: 16:22:53 09/15/2004
DELETE TMA NAME=RACK:0..7/TMA:0..15;
526DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805b1043
TMA
USER NAME: NSN
COMMAND: Delete TMA:NAME=RACK:0/TMA:0;
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: Operation successful
END OF OUTPUT FOR JOB 15
Operation Failed
The specified Object has not been deleted. Additionally to the general NACK causes, a specific NACK cause, meaning that the command is inconsistent with physical configu-ration, is possible.
Application Guidelines:
• TMA must be locked in phase 3 before deletion
• If a DULNA or DILNA with attribute "InaPredecessor" containing a TMA should be deleted, then the tMA contained the attribute has to be deleted before
Example of Command Execution:Delete TMA:NAME=RACK:0/TMA:0;
GET TMA
Command Tree:“MANAGED-ELEMENT h BSS-EQUIPMENT h BTSEP h RACK h TMA h GET TMA”
Applicability:Phase 2 and Phase 3.
Visibility level: 0.
Command Description:new information
Long Names:NAME Address of the managed object
REQATTL Required attribute list
ALS alarmStatus
AST administrativeState
AVS availabilityStatus
OST operationalState
GET TMA NAME=RACK:0..7/TMA:0..15 [,REQATTL=ALS, AST, AVS, OST, PRS, RELFUNCOBJ, PRDINF, ANTMN, ANTSN, BND<x>, BMWD<x>, GN<x>, SUBUNT, RXBMINF, RXBMAXF, TXBMINF, TXBMAXF, MAXGN, MINGN, GNR, INSD, INSID, BTSID, SCID, ANTB, MTLT];
DN0933412 Issue 01527
BTSplus mainline commands at the Flexi BSC product family
TMA
Id:0900d805805b1043
PRS proceduralStatus
RELFUNCOBJ relatedFuncObjects
PRDINF productInfo(prodNbr_SN_HwVer_SwVer)
ANTMN antennaModelNumber
ANTSN antennaSerialNumber
BND<x> band<x>
BMWD<x> beamWidth<x>(degree)
GN<x> gain0(dBi*1<x>)
SUBUNT subUnitType
RXBMINF rxBandMinFreq(kHz*100)
RXBMAXF rxBandMaxFreq(kHz*100)
TXBMINF txBandMinFreq(kHz*100)
TXBMAXF txBandMaxFreq(kHz*100)
MAXGN maxGain(dB*4)
MINGN minGain(dB*4)
GNR gainResolution(dB*4)
INSD installDate
INSID installerId
BTSID baseStationId
SCID sectorId
ANTB antennaBearing(degree)
MTLT mechanicalTilt(degree*10)
System Responses:Operation Completed
None.
Operation Failed
None.
Application Guidelines:None.
Example of Command Execution:GET TMA: NAME=RACK:0/TMA:0, REQATTL=ALS&AST&AVS&OST&PRS&REL-FUNCOBJ&ANTMN& ANTSN& BND0& BMWD0& GN0& BND1& BMWD1& GN1&BND2& BMWD2& GN2& BND3& BMWD3& GN3& SUBUNT& RXBMINF& RXB-MAXF&TXBMINF& TXBMAXF& MAXGN& MINGN& GNR& INSD& INSID& BTSID& SCID&ANTB& MTLT;
GET TMA PRODUCTINFOGET TMA PRODUCT-INFO
NAME=RACK:0..7/TMA:0..15;
528DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805b1043
TMA
Command Tree:“MANAGED-ELEMENT h BSS-EQUIPMENT h BTSEP h RACK h TMA h GET TMA PRODUCTINFO”
Applicability:Phase 2 and Phase 3.
Visibility level: 0.
Command Description:new information
Long Names:NAME Address of the managed object
REQATTL Required attribute list
System Responses:Operation Completed
After command execution, a message of Changed Configuration Notification is dis-played. A further message indicates the result of the operation. An example of get product info command is the following:
JOB: 90
PC Time&Date: 15.05.2008 10:09:30 +02:00
NE Time&Date: 01.01.1990 00:05:05 +00:00
USER NAME: NSN
COMMAND: Get TMA PRODUCTINFO:NAME=RACK:0/TMA:0;
SW RELEASE: 01-04-19-01-01-MB_08-05-13
COMMAND RESULT:Operation successful
productInfo(prodNbr_SN_HwVer_SwVer) = "CS7299111.02; X9081012052;
HW_V_A06; FW_V02.02.00_BL_V02.02.00"
END OF OUTPUT FOR JOB 90.
Binary Command
0d 00 80 ff 12 02 81 81 ab 1a 00 00 1a 01 a1
Binary Response
4a 00 80 00 02 12 01 82 ab 1a 00 00 a1 3e 43 53 37 32 39 39
31 31 31 2e 30 32 3b 20 58 39 30 38 31 30 31 32 30 35 32 3b
20 48 57 5f 56 5f 41 30 36 3b 20 46 57 5f 56 30 32 2e 30 32
2e 30 30 5f 42 4c 5f 56 30 32 2e 30 32 2e 30 30
Operation Failed
None.
Application Guidelines:None.
DN0933412 Issue 01529
BTSplus mainline commands at the Flexi BSC product family
TMA
Id:0900d805805b1043
Example of Command Execution:GET TMA PRODUCTINFO: NAME=RACK:0TMA:0, REQATTL= PRDINF;
GETTEST TMA
Command Tree:“MANAGED-ELEMENT h BSS-EQUIPMENT h BTSEP h RACK h TMA h GETTEST TMA”
Applicability:Phase 2 and Phase 3.
Visibility level: 0.
Command Description:This command displays the attributes of the TMA test.
Long Names:NAME Address of the managed object
REQATTL Required attribute list
System Responses:Operation Completed
After command execution, a message of Changed Configuration Notification is dis-played. A further message indicates the result of the operation. An example of gettest command is the following:
JOB: 239
PC Time&Date: 14:50:09 03/23/2005
NE Time&Date: 00:17:47 09/15/2004
USER NAME: NSN
COMMAND: Gettest TMA:NAME=RACK:0/TMA:0;
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: Operation successful
MOT = RACK:0/TMA:0
testMonitor =
phaseId = PreliminaryTestsTma
phaseStatus = Running
phaseId = CheckAlarmStatusTma
phaseStatus = Waiting
GETTEST TMA NAME=RACK:0..7/TMA:0..15;
530DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805b1043
TMA
phaseId = EndTestTma
phaseStatus = Waiting
testOutcome = INCONCLUSIVE
testState = INITIALIZING
END OF OUTPUT FOR JOB 239
Operation Failed
The GET command has not been successfully executed. A general NACK will indicate possible errors or a specific NACK strictly related to the single command is possible.
Application Guidelines:None.
Example of Command Execution:Gettest TMA:NAME=RACK:0/TMA:0;
LOCK TMA
Command Tree:“MANAGED-ELEMENT h BSS-EQUIPMENT h BTSEP h RACK h TMA h LOCK TMA”
Applicability:Phase 2 and Phase 3.
Visibility level: 1.
testMonitor it is a list of all test phases related to the selected object; for each phase the related phaseStatus is provided (Passed, Failed, Running or Waiting).
phaseId =
phaseStatus =
phaseId =
phaseStatus =
...
...
testOutcome It represents the test result: it can be Inconclusive (if the phases already executed were successful) or Fail (if at least one of the executed phases failed).
testState = Testing It can assume one of the following values: not_initialized, idle, initializing, sus-pended, testing, terminating and dis-abled.
LOCK TMA NAME=RACK:0..7/TMA:0..15;
DN0933412 Issue 01531
BTSplus mainline commands at the Flexi BSC product family
TMA
Id:0900d805805b1043
Command Description:This command changes the administrative state of the TMA (Tower Mounted Amplifier) of the BTSE.
Long Names:NAME Address of the managed object
System Responses:Operation Completed
The specified change of administrative state has been perfomed:
JOB: 8
PC Time&Date: 16:24:42 03/23/2005
NE Time&Date: 16:22:36 09/15/2004
USER NAME: NSN
COMMAND: Lock TMA:NAME=RACK:0/TMA:0;
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: Operation successful
administrativeState = Locked
END OF OUTPUT FOR JOB 8
CHANGED STATE EVENT REPORT:
This provides information about the administrative state, the operational state and the availability status every time a state change occurs:
JOB: 9
PC Time&Date: 16:24:42 03/23/2005
NE Time&Date: 16:22:36 09/15/2004
USER NAME: NSN
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: Operation successful
CHANGED STATE EVENT REPORT:
NAME = RACK:0/TMA:0
Administrative State = LOCKED
532DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805b1043
TMA
Notification Identifier = 461
END OF OUTPUT FOR JOB 9
Operation Failed
The specified change of administrative state has not been performed (e.g. the object is redundant and its spare copy is disabled or already locked, a subordinate resource cannot go into disabled state with "dependency" availability status).
Application Guidelines:None.
Example of Command Execution:Lock TMA:NAME=RACK:0/TMA:0;
PERFTEST TMA
Command Tree:“MANAGED-ELEMENT h BSS-EQUIPMENT h BTSEP h RACK h TMA h PERFTEST TMA”
Applicability:Phase 2 and Phase 3.
Visibility level: 1.
Command Description:This command is used to start an asynchronous test in TMA.
Long Names:NAME Address of the managed object
System Responses:Operation Completed
Test configuration has been set and the specified test has been started. The System response will not be addressed to the MOT but to the object BTSE.
JOB: 240
PC Time&Date: 14:50:09 03/23/2005
NE Time&Date: 00:17:47 09/15/2004
USER NAME: NSN
COMMAND: Perftest TMA:NAME=RACK:0/TMA:0;
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: Operation successful
PERFTEST TMA NAME=RACK:0..7/TMA:0..15;
DN0933412 Issue 01533
BTSplus mainline commands at the Flexi BSC product family
TMA
Id:0900d805805b1043
MOT = RACK:0/TMA:0
tO = BTSETEST:1
END OF OUTPUT FOR JOB 240
JOB: 241
PC Time&Date: 14:50:09 03/23/2005
NE Time&Date: 00:17:47 09/15/2004
USER NAME: NSN
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: Operation successful
ChangedConfigurationNotification:
name = BTSETEST:1
ChangeInfo = created
END OF OUTPUT FOR JOB 241
JOB: 242
PC Time&Date: 14:50:12 03/23/2005
NE Time&Date: 00:17:51 09/15/2004
USER NAME: NSN
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: Operation successful
CHANGED STATE EVENT REPORT:
NAME = RACK:0/TMA:0
Operational State = ENABLED
Availability Status = NULL_value
Notification Identifier = 143
END OF OUTPUT FOR JOB 242
534DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805b1043
TMA
JOB: 243
PC Time&Date: 14:50:12 03/23/2005
NE Time&Date: 00:17:51 09/15/2004
USER NAME: NSN
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: Operation successful
Test Report:
name = BTSETEST:1
testOutcome = PASSED
testTermination = Normal
MOT = RACK:0/TMA:0
executedPhases =
PreliminaryTestsTma
CheckAlarmStatusTma
EndTestTma
END OF OUTPUT FOR JOB 243
JOB: 244
PC Time&Date: 14:50:09 03/23/2005
NE Time&Date: 00:17:47 09/15/2004
USER NAME: NSN
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: Operation successful
ChangedConfigurationNotification:
name = BTSETEST:1
ChangeInfo = deleted
END OF OUTPUT FOR JOB 244
The test results will be displayed at the end of the test phases.
DN0933412 Issue 01535
BTSplus mainline commands at the Flexi BSC product family
TMA
Id:0900d805805b1043
Operation Failed
This NACK-message occurs in the following cases: Message cannot be performed, test not supported, capacity restrictions, physical configuration cannot be performed, object not locked.
Application Guidelines:
• In phase 3 MO must be locked previous to the command execution
Result TEST:
name = TEST:<n>
testOutcome = This field represents the test result; one of the fol-lowing values can be displayed:
Pass all the test phases are successfully performed.
Inconclusive the test is aborted by the system or the test is terminated by the opera-tor.
Fail if at least one of the executed phases fail.
mOts = It is the identifier of the hardware object under test.
testTermination = It specifies how the test is terminated, it can assume the following values:
Normal all the test phases are performed.
Abort the test is aborted by system.
Cancel the test is terminated by operator.
executedPhases
phaseId = It represents the list of the executed test phases (in case of successful test result, all the test phases will be listed).
additionalWords =
....
failedPhases
phaseId = It represents the list of the failed test phase; addi-tional information is provided for each phase.phaseId =
....
skippedPhases
phaseId = It represents the list of the skipped phases; they are displayed only for test stopped during it execution.phaseId =
....
poprosedRepair Action =
A list of most probable fail probable causes is shown (max four messages)
536DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805b1043
TMA
Example of Command Execution:Perftest TMA:NAME=RACK:0/TMA:0;
STOPTEST TMA
Command Tree:“MANAGED-ELEMENT h BSS-EQUIPMENT h BTSEP h RACK h TMA h STOPTEST TMA”
Applicability:Phase 2 and Phase 3.
Visibility level: 1.
Command Description:This command is used to stop a diagnostic previously started.
Long Names:NAME Address of the managed object
System Responses:Operation Completed
Test has been stopped. The System Responses will not be addressed to the MOT but to the object BTSEP.
STOPTEST TMA NAME=RACK:0..7/TMA:0..15;
Result TEST:
name = TEST:<n>
testOutcome = inconclusive
mOts = It is the identifier of the hardware object under test.
testTermination = Cancel
executedPhases
phaseId = It represents the list of the executed test phases; the list is not shown for test in the waiting list (queued)....
.
failedPhases
phaseId = It represents the list of the failed test phase;
additional information is provided for each phase.phaseId =
....
skippedPhases
phaseId = It represents the list of the skipped phases;the list is not shown for test in the waiting list (queued).phaseId =
DN0933412 Issue 01537
BTSplus mainline commands at the Flexi BSC product family
TMA
Id:0900d805805b1043
Operation Failed
Test has not been stopped. This NACK-message can occur when the specified test is not running or in case of test which cannot be stopped.
Application Guidelines:None.
Example of Command Execution:Stoptest TMA:NAME=RACK:0/TMA:0;
UNLOCK TMA
Command Tree:“MANAGED-ELEMENT h BSS-EQUIPMENT h BTSEP h RACK h TMA h UNLOCK TMA”
Applicability:Phase 2 and Phase 3.
Visibility level: 1.
Command Description:This command changes the administrative state of the TMA (Tower Mounted Amplifier) to the BTSE.
Long Names:NAME Address of the managed object
System Responses:Operation Completed
The specified change of administrative state has been perfomed:
JOB: 10
PC Time&Date: 16:24:48 03/23/2005
NE Time&Date: 16:22:42 09/15/2004
USER NAME: NSN
COMMAND: Unlock TMA:NAME=RACK:0/TMA:0;
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: Operation successful
administrativeState = Unlocked
END OF OUTPUT FOR JOB 10
UNLOCK TMA NAME=RACK:0..7/TMA:0..15;
538DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805b1043
TMA
CHANGED STATE EVENT REPORT:
This provides information about the administrative state, the operational state and the availability status every time a state change occurs:
JOB: 11
PC Time&Date: 16:24:48 03/23/2005
NE Time&Date: 16:22:42 09/15/2004
USER NAME: NSN
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: Operation successful
CHANGED STATE EVENT REPORT:
NAME = RACK:0/TMA:0
Administrative State = UNLOCKED
Notification Identifier = 462
END OF OUTPUT FOR JOB 11
Operation Failed
The specified change of administrative state has not been performed.
Application Guidelines:None.
Example of Command Execution:Unlock TMA:NAME=RACK:0/TMA:0;
DN0933412 Issue 01539
BTSplus mainline commands at the Flexi BSC product family
TRX
Id:0900d805805b1045
TRXThe TRX object models the transceivers connected to a certain Flexi BSCproduct family.
GET TRX
Command Tree:“MANAGED-ELEMENT h BSS-FUNCTIONAL h BTSM h BTS h TRX h GET TRX”
Applicability:Phase 3.
Visibility level: 0.
Command Description:This command displays the attributes of the specified Transceiver.
Long Names:NAME Address of the managed object
REQATTL Required attribute list
ABISCH abisChannel
ANTHOPHW antennaHoppingHw
AST administrativeState
AVS availabilityStatus
DLTESTFREQ dlTestFrequency
DMACFHSYID dmaCFHSyId
DYNPOOLINFO dynamicPoolInfo
MOEC memberOfEmergencyConfig
OST operationalState
PWRRED txPwrMaxReduction(*-2dB)
RADIOMG radioMeasGran
RADIOMR radioMeasRep
TEI tei
TESTMODE enableTestMode
TESTPWRRED testPowerReduction
TRXAREA trxArea
TRXCPBL trxCapability
GET TRX NAME=BTS:0..11/TRX:0..23 [,REQATTL=ABISCH, ANTHOPHW, AST, AVS, DLTESTFREQ, DMACFHSYID, DYNPOOLINFO, MOEC, OST, PWRRED, RADIOMG, RADIOMR, TEI, TESTMODE, TESTPWRRED, TRXAREA, TRXCPBL, TRXFREQ, TRXMD, RADIUSEXT];
540DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805b1045
TRX
TRXFREQ carrierFrequency
TRXMD trxMode
RADIUSEXT radiusExtension(km)
System Responses:Operation Completed
After command execution, a message of Changed Configuration Notification is dis-played. A further message indicates the result of the operation. An example of get command is the following:
JOB: 18
PC Time&Date: 11:33:24 03/23/2005
NE Time&Date: 11:31:14 09/15/2004
USER NAME: NSN
COMMAND: Get TRX:NAME=BTS:0/TRX:0;
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: Operation successful
abisChannel =
BPORT = 0
TSL = 1
SSL = NOT_USED
antennaHoppingHw =
administrativeState = Unlocked
availabilityStatus = Dependency
memberOfEmergencyConfig = TRUE
operationalState = DISABLED
txPwrMaxReduction(*-2dB) = 6
radioMeasGran = 1
radioMeasRep = ON
trxArea = NONE
carrierFrequency = 21
tei = 1
trxCapability = UNKNOWN
trxMode = GSM
END OF OUTPUT FOR JOB 18
Operation Failed
DN0933412 Issue 01541
BTSplus mainline commands at the Flexi BSC product family
TRX
Id:0900d805805b1045
The GET command has not been successfully executed. A general NACK will indicate possible errors or a specific NACK strictly related to the single command is possible.
Application Guidelines:
• The TRX attribute trxCapability reflects the type of CU (GSM or EDGE) which is allo-cated to the TRX. If no CU isallocated, the attribute is set to "none". This static assignment is not reasonable, because even if the TRX is disabled a CU may be still allocated to the TRX (e.g. faulty combiner equipment)
Example of Command Execution:Get TRX:NAME=BTS:0/TRX:0,REQATTL=ABISCH&ANTHOPHW&AST&AVS&
DMACFHSYID&MOEC&OST&PWRRED&RADIOMG&RADIOMR&TEI&TRXAREA&
TRXCPBL&TRXFREQ&TRXMD;
GETRELATIONSHIP TRX
Command Tree:“MANAGED-ELEMENT h BSS-FUNCTIONAL h BTSM h BTS h TRX h GETRELATIONSHIP TRX”
Applicability:Phase 3.
Visibility level: 0.
Command Description:This command displays the attributes of the specified Transceiver.
Long Names:NAME Address of the managed object
REQATTL Required attribute list
System Responses:Operation Completed
After command execution, a message of Changed Configuration Notification is dis-played. A further message indicates the result of the operation. An example of get rela-tionship command is the following:
JOB: 161
PC Time&Date: 12:04:08 03/23/2005
NE Time&Date: 13:05:43 09/15/2004
USER NAME: NSN
COMMAND: Getrelationship TRX:NAME=BTS:0/TRX:0;
GETRELATIONSHIP TRX
NAME=BTS:0..11/TRX:0..23;
542DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805b1045
TRX
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: Operation successful
relatedEquipObjects =
RACK:0/COBA:0
RACK:0/CU:3
RACK:0/DUVSWR:3
RACK:0/DULNA:2
RACK:0/TMA:2
RACK:0/DUDCTMA:2
RACK:0/DULNA:3
RACK:0/TMA:3
RACK:0/DUDCTMA:3
END OF OUTPUT FOR JOB 161
Operation Failed
The GET command has not been successfully executed. A general NACK will indicate possible errors or a specific NACK strictly related to the single command is possible.
Application Guidelines:None.
Example of Command Execution:Getrelationship TRX:NAME=BTS:0/TRX:0;
DN0933412 Issue 01543
BTSplus mainline commands at the Flexi BSC product family
XCONNECT
Id:0900d805805b1047
XCONNECTThe XCONNECT object represents an hardware BTSE object that enables the cross-connection between PCM timeslots of different ports of related BTSplus mainline.
CREATE XCONNECT
Command Tree:“MANAGED-ELEMENT h BSS-EQUIPMENT h BTSEP h XCONNECT h CREATE XCONNECT”
Applicability:Phase 2 and Phase 3.
Visibility level: 2.
Command Description:This command provides the XCONNECT (Multidrop-Star CrossConnect) of 64Kbit/s timeslots and additionally a mapping of the timeslot position is provided. This command allows also the PCM30/24 conversion.
Long Names:NAME Address of the managed object
MPTSLXX mappingTSLXX
System Responses:Operation Completed
After command execution, a message of Changed Configuration Notification is dis-played. A further message indicates the result of the operation. An example of create command is the following:
JOB: 15
PC Time&Date: 12:05:31 03/23/2005
NE Time&Date: 12:03:22 09/15/2004
USER NAME: NSN_Brigitte
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: Operation successful
ChangedConfigurationNotification:
name = XCONNECT:0
ChangeInfo = created
CREATE XCONNECT NAME=XCONNECT:0..7 [,MPTSLXX=];
544DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805b1047
XCONNECT
END OF OUTPUT FOR JOB 15
JOB: 16
PC Time&Date: 12:05:31 03/23/2005
NE Time&Date: 12:03:22 09/15/2004
USER NAME: NSN_Brigitte
COMMAND: Create XCONNECT:NAME=XCONNECT:0;
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: Operation successful
END OF OUTPUT FOR JOB 16
Operation Failed
The specified Object has not been created. In addition to the general NACK causes, a specific NACK cause, which indicates that the command is inconsistent with the physical configuration, is possible. An example is the following:
JOB: 81
PC Time&Date: 16:37:54 03/23/2005
NE Time&Date: 16:35:47 09/15/2004
USER NAME: NSN
COMMAND: Create XCONNECT:NAME=XCONNECT:0;
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: OPERATION FAILED
Object instance unknown (-9)
END OF OUTPUT FOR JOB 81
Application Guidelines:
• A XConnect instance is always related to a primary BPort instance. So this target BPort instance must be created before and configured as StarX
• A cross connection can only be established between a primary circuit and a second-ary circuit, but not between two primary circuits or secondary circuits
• A secondary circuit can only be used for cross connect functionality
• A remapping can only be performed for a primary circuit. Only for traffic or signalling timeslots the remapping is applicable, but not for a layer1 control timeslot
DN0933412 Issue 01545
BTSplus mainline commands at the Flexi BSC product family
XCONNECT
Id:0900d805805b1047
• TS 0 means to delete the TS of the XConnect
Example of Command Execution:Create XCONNECT:NAME=XCONNECT:0,MPTSL01=0-0;
DELETE XCONNECT
Command Tree:“MANAGED-ELEMENT h BSS-EQUIPMENT h BTSEP h XCONNECT h DELETE XCONNECT”
Applicability:Phase 2 and Phase 3.
Visibility level: 2.
Command Description:This command deletes the XCONNECT (Multidrop-Star CrossConnect) of 64Kbit/s timeslots from the BTSE data base.
Long Names:NAME Address of the managed object
System Responses:Operation Completed
After command execution, a message of Changed Configuration Notification is dis-played. A further message indicates the result of the operation. An example of delete command is the following:
JOB: 25
PC Time&Date: 12:07:08 03/23/2005
NE Time&Date: 12:04:59 09/15/2004
USER NAME: NSN
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: Operation successful
ChangedConfigurationNotification:
name = XCONNECT:0
ChangeInfo = deleted
END OF OUTPUT FOR JOB 25
DELETE XCONNECT NAME=XCONNECT:0..7;
546DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805b1047
XCONNECT
JOB: 26
PC Time&Date: 12:07:08 03/23/2005
NE Time&Date: 12:04:59 09/15/2004
USER NAME: NSN
COMMAND: Delete XCONNECT:NAME=XCONNECT:0;
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: Operation successful
END OF OUTPUT FOR JOB 26
Operation Failed
The specified Object has not been deleted. Additionally to the general NACK causes, a specific NACK cause, meaning that the command is inconsistent with physical configu-ration, is possible.
Application Guidelines:
• Deletion of a secondary circuit is only allowed, if there are no cross connections established to the related BPort instance
• Deletion of XConnect is possible in phase 2 or phase 3
• In phase 3 the XConnect object must be locked before it can be deleted
Example of Command Execution:Delete XCONNECT:NAME=XCONNECT:0;
GET XCONNECT
Command Tree:“MANAGED-ELEMENT h BSS-EQUIPMENT h BTSEP h XCONNECT h GET XCONNECT”
Applicability:Phase 2 and Phase 3.
Visibility level: 0.
Command Description:This command displays the attributes of XCONNECT (Multidrop-Star CrossConnect) and additionally of the timeslot position mapping.
Long Names:NAME Address of the managed object
GET XCONNECT NAME=XCONNECT:0..7 [,REQATTL=ALS, AST, AVS, MPTSLXX, OST, PRS, RELFUNCOBJ];
DN0933412 Issue 01547
BTSplus mainline commands at the Flexi BSC product family
XCONNECT
Id:0900d805805b1047
REQATTL Required attribute list
ALS alarmStatus
AST administrativeState
AVS availabilityStatus
MPTSLXX mappingTSLXX
OST operationalState
PRS proceduralStatus
RELFUNCOBJ relatedFuncObjects
System Responses:Operation Completed
After command execution, a message of Changed Configuration Notification is dis-played. A further message indicates the result of the operation. An example of get command is the following:
JOB: 17
PC Time&Date: 12:05:47 03/23/2005
NE Time&Date: 12:03:37 09/15/2004
USER NAME: NSN
COMMAND: Get XCONNECT:NAME=XCONNECT:0;
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: Operation successful
alarmStatus = CLEARED
administrativeState = Unlocked
availabilityStatus = NULL
mappingTSL01 =
targetBport = 0
targetTSL = 0
mappingTSL02 =
targetBport = 0
targetTSL = 0
mappingTSL03 =
targetBport = 0
targetTSL = 0
mappingTSL04 =
targetBport = 0
targetTSL = 0
548DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805b1047
XCONNECT
mappingTSL05 =
targetBport = 0
targetTSL = 0
mappingTSL06 =
targetBport = 0
targetTSL = 0
mappingTSL07 =
targetBport = 0
targetTSL = 0
mappingTSL08 =
targetBport = 0
targetTSL = 0
mappingTSL09 =
targetBport = 0
targetTSL = 0
mappingTSL10 =
targetBport = 0
targetTSL = 0
mappingTSL11 =
targetBport = 0
targetTSL = 0
JOB: 17
mappingTSL12 =
targetBport = 0
targetTSL = 0
mappingTSL13 =
targetBport = 0
targetTSL = 0
mappingTSL14 =
targetBport = 0
targetTSL = 0
mappingTSL15 =
targetBport = 0
targetTSL = 0
mappingTSL16 =
targetBport = 0
targetTSL = 0
mappingTSL17 =
targetBport = 0
DN0933412 Issue 01549
BTSplus mainline commands at the Flexi BSC product family
XCONNECT
Id:0900d805805b1047
targetTSL = 0
mappingTSL18 =
targetBport = 0
targetTSL = 0
mappingTSL19 =
targetBport = 0
targetTSL = 0
mappingTSL20 =
targetBport = 0
targetTSL = 0
mappingTSL21 =
targetBport = 0
targetTSL = 0
mappingTSL22 =
targetBport = 0
targetTSL = 0
mappingTSL23 =
targetBport = 0
targetTSL = 0
mappingTSL24 =
targetBport = 0
targetTSL = 0
mappingTSL25 =
targetBport = 0
targetTSL = 0
mappingTSL26 =
targetBport = 0
targetTSL = 0
mappingTSL27 =
targetBport = 0
targetTSL = 0
JOB: 17
mappingTSL28 =
targetBport = 0
targetTSL = 0
mappingTSL29 =
targetBport = 0
targetTSL = 0
mappingTSL30 =
550DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805b1047
XCONNECT
targetBport = 0
targetTSL = 0
mappingTSL31 =
targetBport = 0
targetTSL = 0
operationalState = ENABLED
proceduralStatus = NULL
relatedFuncObjects =
END OF OUTPUT FOR JOB 17
Operation Failed
The GET command has not been successfully executed. A general NACK will indicate possible errors or a specific NACK strictly related to the single command is possible.
Application Guidelines:None.
Example of Command Execution:Get XCONNECT:NAME=XCONNECT:0,REQATTL=ALS&AST&AVS&
MPTSL01&MPTSL02&MPTSL03&MPTSL04&MPTSL05&MPTSL06&MPTSL07&
MPTSL08&MPTSL09&MPTSL10&MPTSL11&MPTSL12&MPTSL13&MPTSL14&
MPTSL15&MPTSL16&MPTSL17&MPTSL18&MPTSL19&MPTSL20&MPTSL21&
MPTSL22&MPTSL23&MPTSL24&MPTSL25&MPTSL26&MPTSL27&MPTSL28&
MPTSL29&MPTSL30&MPTSL31&OST&PRS&RELFUNCOBJ;
LOCK XCONNECT
Command Tree:“MANAGED-ELEMENT h BSS-EQUIPMENT h BTSEP h XCONNECT h LOCK XCONNECT”
Applicability:Phase 2 and Phase 3.
Visibility level: 1.
Command Description:This command changes the administrative state of the XCONNECT (Multidrop-Star CrossConnect).
Long Names:NAME Address of the managed object
System Responses:Operation Completed
LOCK XCONNECT NAME=XCONNECT:0..7;
DN0933412 Issue 01551
BTSplus mainline commands at the Flexi BSC product family
XCONNECT
Id:0900d805805b1047
The specified change of administrative state has been perfomed:
JOB: 19
PC Time&Date: 12:06:07 03/23/2005
NE Time&Date: 12:03:58 09/15/2004
USER NAME: NSN
COMMAND: Lock XCONNECT:NAME=XCONNECT:0;
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: Operation successful
administrativeState = Locked
END OF OUTPUT FOR JOB 19
CHANGED STATE EVENT REPORT:
This provides information about the administrative state, the operational state and the availability status every time a state change occurs:
JOB: 18
PC Time&Date: 12:06:02 03/23/2005
NE Time&Date: 12:03:54 09/15/2004
USER NAME: NSN
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: Operation successful
CHANGED STATE EVENT REPORT:
NAME = XCONNECT:0
Administrative State = LOCKED
Notification Identifier = 3151
END OF OUTPUT FOR JOB 18
Operation Failed
552DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805b1047
XCONNECT
The specified change of administrative state has not been performed (e.g. the object is redundant and its spare copy is disabled or already locked, a subordinate resource cannot go into disabled state with "dependency" availability status).
Application Guidelines:
• This command has no effect on the established connections
Example of Command Execution:Lock XCONNECT:NAME=XCONNECT:0;
SET XCONNECT
Command Tree:“MANAGED-ELEMENT h BSS-EQUIPMENT h BTSEP h XCONNECT h SET XCONNECT”
Applicability:Phase 2 and Phase 3.
Visibility level: 2.
Command Description:This command sets the attributes for the mapping of the XCONNECT (Multidrop-Star CrossConnect) 64Kbit/s timeslot position.
Long Names:NAME Address of the managed object
MPTSLXX mappingTSLXX
System Responses:Operation Completed
The specified attribute has been set. In addition, a Changed Attribute Event Report indi-cates that the command has been successfully executed:
JOB: 20
PC Time&Date: 12:06:33 03/23/2005
NE Time&Date: 12:04:23 09/15/2004
USER NAME: NSN
COMMAND: Set XCONNECT:NAME=XCONNECT:0;
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: SET-NACK
Operation successful
SET XCONNECT NAME=XCONNECT:0..7 [,MPTSLXX=];
DN0933412 Issue 01553
BTSplus mainline commands at the Flexi BSC product family
XCONNECT
Id:0900d805805b1047
END OF OUTPUT FOR JOB 20
Operation Failed
The specified Object has not been created. In addition to the general NACK causes, a specific NACK cause, which indicates that the command is inconsistent with the physical configuration, is possible.
Application Guidelines:
• A secondary circuit cannot be changed to a primary circuit and vice versa via a SET command
• A remapping can only be performed for a primary circuit
• Only for traffic or signalling timeslots the remapping is applicable, but not for a layer1 control timeslot
Example of Command Execution:Set XCONNECT:NAME=XCONNECT:0,MPTSL01=0-0;
UNLOCK XCONNECT
Command Tree:“MANAGED-ELEMENT h BSS-EQUIPMENT h BTSEP h XCONNECT h UNLOCK XCONNECT”
Applicability:Phase 2 and Phase 3.
Visibility level: 1.
Command Description:This command changes the administrative state of the XCONNECT (Multidrop-Star CrossConnect).
Long Names:NAME Address of the managed object
System Responses:Operation Completed
The specified change of administrative state has been perfomed:
JOB: 22
PC Time&Date: 12:06:46 03/23/2005
NE Time&Date: 12:04:37 09/15/2004
USER NAME: NSN
COMMAND: Unlock XCONNECT:NAME=XCONNECT:0;
UNLOCK XCONNECT NAME=XCONNECT:0..7;
554DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805b1047
XCONNECT
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: Operation successful
administrativeState = Unlocked
END OF OUTPUT FOR JOB 22
CHANGED STATE EVENT REPORT:
This provides information about the administrative state, the operational state and the availability status every time a state change occurs:
JOB: 21
PC Time&Date: 12:06:46 03/23/2005
NE Time&Date: 12:04:37 09/15/2004
USER NAME: NSN
SW RELEASE: 01-04-17-01-26-51_05-02-23
COMMAND RESULT: Operation successful
CHANGED STATE EVENT REPORT:
NAME = XCONNECT:0
Administrative State = UNLOCKED
Notification Identifier = 3154
END OF OUTPUT FOR JOB 21
Operation Failed
The specified change of administrative state has not been performed.
Application Guidelines:
• This command has no effect on the established connections
Example of Command Execution:Unlock XCONNECT:NAME=XCONNECT:0;
DN0933412 Issue 01555
BTSplus mainline commands at the Flexi BSC product family
Parameters/attributes in alphabetical order
Id:0900d8058053dfb4
3 Parameters/attributes in alphabetical orderg Please note that the abbreviations marked with an * are not real parameters.
556DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805b2e2f
a
a
ABISCHabisChannel
This attribute identifies the Timeslot Number and Sublot Number allocated on the Abis-interface.This attribute exists for CHAN and TRX objects. The attribute refers to a radio signalling link (RSL): it indicates just the default channel for the RSL - a more actual information is reflected in the object LAPDLE.
Validity RangeBPORT (TRX): 00-07 (for BS-82 II only, BPortNumber 00-03 is allowed)
TSL:
• 01-1Ffor PCM30 • 01-18 for PCM24
SSL:
• 0 for bit 7 and 6 on LMT Evolution displayed "SSL0” • 1 for bit 5 and 4 on LMT Evolution displayed "SSL1" • 2 for bit 3 and 2 on LMT Evolution displayed "SSL2" • 3 for bit 1 and 0 on LMT Evolution displayed "SSL3"
g 0x10 for bit 7, 6, 5 and 4 on LMT Evolution displayed "SSL0_32KB", 0x11 for bit 3, 2, 1 and 0 on LMT Evolution displayed "SSL1_32KB", 0xFF 64 kbit/sec on LMT Evolution displayed "NOT_USED" are valid only for the abisChannel attribute on object TRX.
There is no dedicated message to connect the terrestrial traffic channel. The connection is executed by means of the reception of the “SET” message containing this channel attribute.
When this attribute is related to the TRX object, the attribute identifies the associated Abis physical link for RSL signaling. Moreover, there must be a LAPDLE instance asso-ciated with this link.
When this attribute is related to the CHAN object, the attribute identifies the associated Abis physical link for radio traffic channel.
Default ValueNone.
Contained in the following commands: GET CHAN, GET TRX
ABISLKSATsAbisLinkSatellited
The attribute informs the BTSE SW about the presence of a satellite on the Asub inter-face.
DN0933412 Issue 01557
BTSplus mainline commands at the Flexi BSC product family
a
Id:0900d805805b2e2f
Validity Range
Default ValueterrestrialConnection
Contained in the following commands: GET BTSM NOSWL, SET BTSM
ABISTIMEsAbisExternalTime
This attribute provides the time-of-day time of the BTSE. This attribute functions as a reference for all time stamp activities in the BTSE. A daily update of the attribute is per-formed via Abis. Additionally the attribute is update after each successful Abis-align-ment.
Validity RangeIn commands GET BTSM NOSWL:
In commands SET BTSM:
Default ValueNone.
Contained in the following commands: GET BTSM NOSWL, SET BTSM
ACBQPFFacBQPFgtFac
acBQPFgtFac defines the forgetting factor for the time exponential filter used for BQP averaging. A change of the attribute becomes effective at the next AC period.
terrestrialConnection
satelliteConnection
<ANY>
<NULL>
year 1992 - 2099
month 1 - 12
day 1 - 31
hour 0 - 23
min 0 - 59
sec 0 - 59
offsetHour -12 - 14
offsetMinute 0 - 45
558DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805b2e2f
a
Validity Range
Default Value 0.2
Contained in the following commands: GET BTS
ACBQPMAXacBQPMax(%)
acBQPMax specifies the maximum tolerated Bad Quality Probability (outage probability) in the cell. If e.g. acFERMax is 5% and acBQPMax is 10% it indicates that more than 10% of the speech samples having a FER with more than 5% is not acceptable. A change of the attribute becomes effective at the next AC period.
Validity Range
Default Value 5%
Contained in the following commands: GET BTS
ACEFLFFacEFLFgtFac
acEFLFgtFac defines the forgetting factor for the exponential filter used for fractional load averaging. A change of the attribute becomes effective at the next AC period.
Validity Range
0.1 - 1.0 10 entries can be selected:
- 1 corresponds to the attribute value 0.1
- 10 corresponds to the attribute value 1.0
2 - 10 9 entries can be selected:
- 2 corresponds to the attribute value 2%
- 10 corresponds to the attribute value 10%
0.02 - 0.20 10 entries can be selected:
- 1 corresponds to the attribute value 0.02
- 10 corresponds to the attribute value 0.20
DN0933412 Issue 01559
BTSplus mainline commands at the Flexi BSC product family
a
Id:0900d805805b2e2f
Default Value 0.04
Contained in the following commands: GET BTS
ACFERMAXacFERMax(%)
acFERMax is a criterion for the speech quality in terms of frame erasure rate (FER).
acFERMax specifies the maximum tolerated FER for speech samples taken over 4 SACCH periods, e.g. acFERMax = 5.0% requires that not more than 5% bad speech frames are allowed in a sample taken over 4 SACCH periods, i.e. the FER over the sampling period of 4 SACCH frames shall be less or equal to 5%. In other words, if the percentage of bad frames (FER > acFERMax) is greater than acFERMax the respective sample will increase the BQP. A change of the attribute becomes effective at the next AC period.
Validity Range
Default Value 5.0%
Contained in the following commands: GET BTS
ACLNKTYPacLinkType
acLinkType defines the type of samples to be collected. It also specifies the way they will be used for the BQP evaluation.
acLinkType == 0 and acLinkType == 2 require EMR (ENHANCED MEASUREMENT REPORTING). A change of the attribute becomes effective at the next AC period.
Validity Range
1.0 - 10.0 19 entries can be selected:
- 1 corresponds to the attribute value 1.0%
- 19 corresponds to the attribute value 10.0%
(the step size is 0.5%)
UL_AND_DL_SAMPLES_SEPARATELY
UL_SAMPLES_ONLY
UL_AND_DL_SAMPLES_COMMONLY
560DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805b2e2f
a
Default Value UL_SAMPLES_ONLY (Collect and evaluate UL samples only)
Contained in the following commands: GET BTS
ACMAXEFLDMAacMaxEFLDMA(%)
acMaxEFLDMA specifies the maximum effective frequency load (EFL). The value is valid for each DMA layer of the cell. A change of the attribute becomes effective at the next AC period.
Validity Range 10%
15%
. .
. .
100%
(starting from 10, 19 entries could be selected, with step size = 5)
Default Value 50%
Contained in the following commands: GET BTS
ACMINEFLDMAacMinEFLDMA(%)
acMinEFLDMA specifies the minimum EFL. The value is valid for each DMA layer of the cell. A change of the attribute becomes effective at the next AC period.
Validity Range 5 5%
10 10%
..
..
50 50%
(starting from 5, the entries could be selected, with step size=5)
Default Value 50%
DN0933412 Issue 01561
BTSplus mainline commands at the Flexi BSC product family
a
Id:0900d805805b2e2f
Contained in the following commands: GET BTS
ACONNalarmConnector
The MDUX alarm line can be assigned to any ACTC alarm connector which is freely configurable via an ENVABTSE object. The relative ENVABTSE must not be created if the related connector is used for the MDUX.
Validity Range
Default ValueNone.
Contained in the following commands: CREATE BCOM, GET BCOM, SET BCOM
ACPERacPeriod
acPeriod specifies the time/length of every Admission Control Period in measurement reporting periods (480 milliseconds) (e.g. 100 periods) used for the periodic AC evalua-tion and the periodic reporting to the Flexi BSC product family via the 'Radio Link Admis-sion Control Message. A change of the attribute becomes effective at the next AC period.
Validity Range 20 20 measurement reporting periods
24 24 measurement reporting periods
. . measurement reporting periods
. . measurement reporting periods
396 396 measurement reporting periods
400 400 measurement reporting periods
(96 possible entries with step size equal to 4)
Default Value 120 measurement reporting periods
Contained in the following commands: GET BTS
ENVA0
ENVA1
...
ENVA8
562DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805b2e2f
a
ACTVINCactivationIncluded
This attribute indicates whether the installed FW is activated automatically by LRU reset or not.
Validity Range
Default ValueNone.
Contained in the following commands: FWUPGRADE BTSM
ALGNSTEPalignmentStep
new information
Validity Range
Default ValueNone.
Contained in the following commands: REQCURSTASYN BTSEP
ALIGCOBAalignedCoba
The attribute indicates that the flash content is potentially incomplete due to a previously interrupted
COBA alignment. 16
The alignedCOBA attribute is automatically set to 'False' by the BTSE if the passive COBA could not be aligned. If the attribute is set to TRUE by the operator (to indicate, that he checked and, if necessary, corrected the Flash-contents to his needs) the according alarm is ceased.
The setting to 'False' via command is rejected.
Validity Range
TRUE
FALSE
summaryObjectsOnly
summarisedObjectsOnly
allObjects
TRUE
DN0933412 Issue 01563
BTSplus mainline commands at the Flexi BSC product family
a
Id:0900d805805b2e2f
Default Value
Contained in the following commands: GET BTSEP NOSWL, SET BTSEP
ALRMCLETalarmClearanceTime
An alarm must not be active at least for this time before it is ceased. The time is expressed by the number of polling periods (1 s).
Validity Range
Default Value
Contained in the following commands: CREATE CESTUNNEL, GET CESTUNNEL, SET CESTUNNEL
ALRMCOUNTERalarmCount
FALSE
TRUE
1 - 20
10
The BTSE supports a filter mechanism for the following failure event reports related to pcm line problems (and is valid for all created BPORT instances).
1. "lower BER threshold exceeded"
2. "external signal absence"
3. "AIS alarm"
4. "frame alignment loss"
5. "higher BER threshold exceeded"
6. "remote alarm"
The following filter mechanism is applied for the failure event reports 1-6 listed above.
An alarm is generated because of 2 possible events:
a) If it is found active for a time interval equal or greater than alarmTiming2.
564DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805b2e2f
a
Validity Range
Default Value
Contained in the following commands: CREATE COBA, GET COBA, SET COBA
ALRMPERTalarmPersistencyTime
All alarms which could toggle must persist at least for this time before an alarm is reported. The time is expressed by the number of polling periods (1 s).
Validity Range
Default Value
Contained in the following commands: CREATE CESTUNNEL, GET CESTUNNEL, SET CESTUNNEL
ALRMSEVXXXalarmSeverityXXX
b) If it is found active with a duration less than alarmTiming2 but it is found active at least as often as alarmCount in a time interval equal to alarmTiming3. The number of the alarm is incremented every time a transition 'not active' to 'active' is detected.
The alarm contains an information in the additional information parameter whether it was detected due to event a) or event b).
An active alarm is cleared if no alarm is found for a time interval equal to alarmTiming1.
1 - 254
32
1 - 20
3
This attribute defines the severity that the BTSE SW has to use for the given type of HW board in case of state transitions from 'enabled' to 'disabled failed'.
A change of the attribute becomes effective with the start of a new failure, i.e. if the attribute is changed and a failure is still pending the change of the attribute will not trigger a 'failure ceased' failure event report together with a failure event report with the new alarmSeveri-tyXXX.
DN0933412 Issue 01565
BTSplus mainline commands at the Flexi BSC product family
a
Id:0900d805805b2e2f
Validity Range
Default Value
Contained in the following commands: GET BTSEP NOSWL, SET BTSEP
ALRMT1/2/3alarmTiming1(sec)/2/3
List of BS240, BS24XL, BS241, BS40, BS41 HW:
ALRMSEVACDC, ALRMSEVACT, ALRMSEVBATTERY,
ALRMSEVCOBA, ALRMSEVCOSA, ALRMSEVCU,
ALRMSEVDIDCTMA, ALRMSEVDILNA, ALRMSEVDUDCTMA,
ALRMSEVDULNA, ALRMSEVDUVSWR, ALRMSEVFANP,
ALRMSEVFCUMAIN,ALRMSEVFCUTR,ALRMSEVFTNFP,
ALRMSEVFVSWRP,ALRMSEVTMA
CRITICAL
MAJOR
MINOR
DEFAULT_DB
DEFAULT_DB
The attribute value is valid for all created BPORT instances.
The BTSE supports a filter mechanism for the following failure event reports related to pcm line problems:
1. "lower BER threshold exceeded"
2. "external signal absence"
3. "AIS alarm"
4. "frame alignment loss"
5. "higher BER threshold exceeded"
6. "remote alarm"
The following filter mechanism is applied for the failure event reports listed above.
An alarm is generated because of 2 possible events:
a) If it is found active for a time interval equal or greater than alarmTiming2.
566DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805b2e2f
a
Validity Range
Default Value
Contained in the following commands: CREATE COBA, GET COBA, SET COBA
ALSalarmStatus
This attribute shows the highest severity of all active alarm conditions related to the managed object. In case of summarization objects a proprietary semantics is used.
Validity Range CLEARED
MINOR
MAJOR
CRITICAL
Default Value CLEARED
Contained in the following commands: GET ACDCP, GET ACT, GET BATTERY, GET BCOM, GET BPORT, GET BTSEP NOSWL, GET CESPW, GET CESTUNNEL, GET COBA, GET COBAETHINTF, GET COSA, GET CU, GET DIDCTMA, GET DILNA, GET DUAMCO, GET DUDCTMA, GET DULNA, GET DUVSWR, GET ENVABTSE, GET ETHCON, GET ETHPORT, GET F6DCTMA, GET F6LNA, GET F6TNFP, GET F6VSWRP, GET FANP, GET FCUMAIN, GET FCUTR, GET FTNFP, GET FVSWRP, GET LAPDLE, GET RACK, GET SYNCBTSE, GET TMA, GET XCONNECT
AMRLKATaMRLinkAdapTuning
This parameter is used by the AMR Uplink Codec Mode Adaptation in the BTSplus mainline. It tunes the transition between codec modes determined by internal thresh-
b) If it is found active with a duration less than alarmTiming2 but it is found active at least as often as alarmCount in a time interval equal to alarmTiming3. The number of the alarm is incremented every time a transition 'not active' to 'active' is detected.
- The alarm contains an information in the additional information parameter whether it was detected due to event a) or event b).
- An active alarm is cleared if no alarm is found for a time interval equal to alarmTiming1.
1 - 254
20
DN0933412 Issue 01567
BTSplus mainline commands at the Flexi BSC product family
a
Id:0900d805805b2e2f
olds. A value higher than the default shifts the transition towards higher carrier-to-inter-ferer or signal-to-noise ratios. A value lower than the default has the opposite effect. The step size is 0,1dB. Adaptation of AMR Half Rate and AMR Full Rate is affected simulta-neously. All possible transitions between modes are generally shifted by the same amount.
However, to account for a limited range of the underlying measurements, shifts of tran-sitions near the upper range limit tend to saturate when shifted closer to the limit. The default value is the optimum setting and normally requires no modification.
Validity Range
Default Value 0 dB
Contained in the following commands: GET BTS
AMRLKATWFSaMRLinkAdapTuningWFS(dB)
This attribute indicates whether the installed FW is be activated automatically by LRU reset or not. This parameter is used by the AMR Uplink Codec Mode Adaptation in the BTSplus mainline. It tunes the transition between codec modes determined by internal thresholds.
A value higher than the default shifts the transition towards higher carrier-to-interferer or signal-to-noise ratios.
A value lower than the default has the opposite effect. The step size is 0,1dB. Adapta-tion of AMR Half Rate and AMR Full Rate is affected simultaneously. All possible tran-sitions between modes are generally shifted by the same amount. However, to account for a limited range of the underlying measurements, shifts of transitions near the upper range limit tend to saturate when shifted closer to the limit.
The default value is the optimum setting and normally requires no modification.
0 - 200 00 -100 (-10 dB)
01 -99
. .
. .
99 -1
100 0 (0 dB)
101 +1
. .
. .
200 +100 (10 dB)
568DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805b2e2f
a
Validity Range
Default ValueNone.
Contained in the following commands: GET BTS
ANT<x>CELLNOant<x>CellNumber
This attribute specifies the number of the cell. The value corresponds to the instance number of the object BTS. The attribute can be only modified if no wiring destinations are configured.
Note: <x> ... <0...5>
so the names of the attributes read:
GUI: ant0CellNumber CLI: ANT0CELLNO
ant1CellNumber ANT1CELLNO
ant2CellNumber ANT2CELLNO
ant3CellNumber ANT3CELLNO
ant4CellNumber ANT4CELLNO
ant5CellNumber ANT5CELLNO
g With the SET BCOM command it is possible to "delete" the parameters setting the value "NULL", not all together but first the wiring date and in a second command the cell parameters (see Application Guidelines: of SET BCOM).
Validity RangeIn commands CREATE BCOM, SET BCOM:
In commands GET BCOM:
Default ValueIn moc(s) BCOM:
None.
In moc(s) BCOM:
Contained in the following commands: CREATE BCOM, GET BCOM, SET BCOM
-10.0 - 10.0
0 - 11
<NULL>
<ANY>
NULL
DN0933412 Issue 01569
BTSplus mainline commands at the Flexi BSC product family
a
Id:0900d805805b2e2f
ANT<x>SCNRXant<x>SecondCellNumberRx
This parameter allows the sharing of one antenna by two cells in order to receive diver-sity.
Validity RangeIn commands CREATE BCOM, SET BCOM:
In commands GET BCOM:
Default ValueIn moc(s) BCOM:
None.
In moc(s) BCOM:
Contained in the following commands: CREATE BCOM, GET BCOM, SET BCOM
ANT<x>WDRXant<x>WiringDataRx
The attribute specifies the carrier unit ports, which are connected to the Rx outputs of a MDUX submodule. The maximum number of destinations is:
• 4 if MDUX only equipped
• 8 if MDUX and DUAMCO equipped
Note: <x> ... <0...5> so the names of the attributes read:
GUI: ant0WiringDataRx CLI: ANT0WDRX
ant1WiringDataRx ANT1WDRX
ant2WiringDataRx ANT2WDRX
ant3WiringDataRx ANT3WDRX
ant4WiringDataRx ANT4WDRX
ant5WiringDataRx ANT5WDRX
The following values are possible for 'RX_wiring n':
H'0012FF00 CU0N (CU0 normal path)
H'00FF00 CU0D (CU0 diversity path)
H'0012FF01 CU1N (CU1 normal path)
H'0112FF01 CU1D (CU1 diversity path)
0 - 11
<NULL>
<ANY>
NULL
570DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805b2e2f
a
H'0012FF02 CU2N (CU2 normal path)
H'0112FF02 CU2D (CU2diversity path)
H'0012FF03 CU3N (CU3 normal path)
H'0112FF03 CU3D (CU3 diversity path)
H'0012FF04 CU4N (CU4 normal path)
H'0112FF04 CU4D (CU4 diversity path)
H'0012FF05 CU5N (CU5 normal path)
H'0112FF05 CU5D (CU5 diversity path)
H'002AFF00 FCUMAIN0N (FCUMAIN0 normal path)
H'012AFF00 FCUMAIN0D (FCUMAIN0 diversity path)
H'022AFF00 FCUMAIN0N1 (FCUMAIN0 Rx C / N1 path)
g With the SET BCOM command it is possible to "delete" the parameters setting the value "NULL", not all together but first the wiring date and in a second command the cell parameters (see Application Guidelines: of SET BCOM).
Validity Range
1 to 8 items of
CU0N
CU0D
CU1N
CU1D
CU2N
CU2D
CU3N
CU3D
CU4N
CU4D
CU5N
CU5D
CU6N
CU6D
CU7N
CU7D
CU8N
CU8D
CU9N
CU9D
DN0933412 Issue 01571
BTSplus mainline commands at the Flexi BSC product family
a
Id:0900d805805b2e2f
CU10N
CU10D
CU11N
CU11D
FCUMAIN0N
FCUMAIN0D
FCUMAIN0N1
FCUMAIN0D1
FCUMAIN1N
FCUMAIN1D
FCUMAIN1N1
FCUMAIN1D1
FCUMAIN2N
FCUMAIN2D
FCUMAIN2N1
FCUMAIN2D1
FCUMAIN3N
FCUMAIN3D
FCUMAIN3N1
FCUMAIN3D1
FCUMAIN4N
FCUMAIN4D
FCUMAIN4N1
FCUMAIN4D1
FCUMAIN5N
FCUMAIN5D
FCUMAIN5N1
FCUMAIN5D1
FCUMAIN6N
FCUMAIN6D
FCUMAIN6N1
FCUMAIN6D1
FCUMAIN7N
FCUMAIN7D
FCUMAIN7N1
FCUMAIN7D1
572DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805b2e2f
a
Default ValueNone.
Contained in the following commands: SETWIRINGRX BCOM
ANT<x>WDTXant<x>WiringDataTx
The attribute specifies the carrier unit ports which are either directly or via HYBRID6 connected to the TX input of an MDUX submodule. The maximum number of destina-tions is:
• 1 if MDUX without HYBRID6 equipped
• 2 if MDUX with HYBRID6 equipped
• 4 if MDUX with HYBRID6 and COAMCO equipped
Validity Range
FCUMAIN8N
FCUMAIN8D
FCUMAIN8N1
FCUMAIN8D1
FCUMAIN9N
FCUMAIN9D
FCUMAIN9N1
FCUMAIN9D1
FCUMAIN10N
FCUMAIN10D
FCUMAIN10N1
FCUMAIN10D1
FCUMAIN11N
FCUMAIN11D
FCUMAIN11N1
FCUMAIN11D1
NULL
<NULL>
1 to 4 items of
CU0
CU1
CU2
DN0933412 Issue 01573
BTSplus mainline commands at the Flexi BSC product family
a
Id:0900d805805b2e2f
CU3
CU4
CU5
CU6
CU7
CU8
CU9
CU10
CU11
FCUMAIN0TX0
FCUMAIN0TX1
FCUMAIN1TX0
FCUMAIN1TX1
FCUMAIN2TX0
FCUMAIN2TX1
FCUMAIN3TX0
FCUMAIN3TX1
FCUMAIN4TX0
FCUMAIN4TX1
FCUMAIN5TX0
FCUMAIN5TX1
FCUMAIN6TX0
FCUMAIN6TX1
FCUMAIN7TX0
FCUMAIN7TX1
FCUMAIN8TX0
FCUMAIN8TX1
FCUMAIN9TX0
FCUMAIN9TX1
FCUMAIN10TX0
FCUMAIN10TX1
FCUMAIN11TX0
FCUMAIN11TX1
NULL
<NULL>
574DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805b2e2f
a
Default ValueNone.
Contained in the following commands: SETWIRINGTX BCOM
ANTBantennaBearing(degree)
Attribute data provided by TMA.
Validity Range
Default ValueNone.
Contained in the following commands: GET TMA
ANTHOPHWantennaHoppingHw
Validity Range
Default ValueNone.
Contained in the following commands: GET TRX
0 - 65535
<NULL>
The attribute shows which antenna hardware is used by a TRX for antenna hopping. The attribute doesn't show how often an antenna hardware is used - i.e. the attribute doesn't reflect the actual antenna hopping sequence. The attribute length is 0 for hh-ii=04-01 if no antenna hopping is used.
Not BR8.0: In a switched beam cell, the attribute shows a list of SDUSEC instances which are enabled in the cell and offer service to the input TRXs (in this case 0 < n < 10).
type of HW = DUVSWR or SDUSEC
N <= 98 (decimal) 0 <= n < 24
0 to 23 items of
Pathname
DN0933412 Issue 01575
BTSplus mainline commands at the Flexi BSC product family
a
Id:0900d805805b2e2f
ANTHOPMODantennaHoppingMode
This attribute specifies whether the BCCH transceiver has to be included in the hopping sequence for Antenna Hopping or not. The attribute is only valid if the feature Antenna Hopping is enabled (attribute enableAntennaHopping).
Validity Range
Default Value NOBCCHTRX
Contained in the following commands: GET BTS
ANTHOPPantennaHoppingPeriod
This attribute specifies how many frames will be transmitted over each antenna before the next antenna will be used to send the frames. The number of antenna changes depends on the number of used antennas and service (4-4-5 used for EDGE).The attri-bute is only valid if the feature Antenna Hopping is enabled (attribute enableAntenna-Hopping).
Validity Range
Default Value SECOND
Contained in the following commands: GET BTS
ANTHOPSTantennaHoppingStatus
This attribute indicates the current status of Antenna Hopping. For a BTSplus mainline using only FICOM (FVSWRP) in transmit direction the attribute value is 'hopping off'. (FALSE = hopping off)
Validity Range
NOBCCHTRX
ALLTRX
ALL
SECOND
FOURTH
SEQ_445
TRUE
576DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805b2e2f
a
Default Value FALSE
Contained in the following commands: GET BTS
ANTMNantennaModelNumber
Attribute data provided by TMA.
Validity Range
Default ValueNone.
Contained in the following commands: GET TMA
ANTSNantennaSerialNumber
Attribute data provided by TMA.
Validity Range
Default ValueNone.
Contained in the following commands: GET TMA
ARFACCHACMDFapplyRFacchOnAnyCmdFrame
This attribute determines the LAPDm frame type on which R-FACCH (Repeated FACCH) is allowed, if the latter has been enabled by the parameter enableRFACCH on the respective codec type. The parameter is implemented as a bitmap consisting of 4 bits:
Bitmap Frame Type LAPDm Frame Type Description
0/1 I (ASSHOCMD) Only I-frames carrying ASS_CMD and HO_CMD. See note 1.
FALSE
0..15 characters string
0..17 characters string
DN0933412 Issue 01577
BTSplus mainline commands at the Flexi BSC product family
a
Id:0900d805805b2e2f
0/1 UI (PHSY_INFO) UI-frames carrying the PHSY_INFO. See note 1.
0/1 I (COMPLEMENTARY) I-frames excluding I (ASSHOCMD). See note 2.
0/1 UA UA response frames. See note 3.
The value '0' denotes R-FACCH is allowed while the value '1' denotes R-FACCH is not allowed on the respective LAPDm frame type.
g Notes:
1. R-FACCH shall not be used on command frames other than I-frames and UI-frames. Both I-frames and UI-frames of LAPDm protocol are used for Information transfer i.e. they contain payload of higher signaling layer. I-frames are transferred in acknowledged mode whereas UI-frames are transferred in Unacknowledged mode.
2. Distinguishing between I-frames carrying ASS_CMD and HO_CMD: I(ASSHOCMD) and the rest of I-frames: I(COMPLEMENTARY) is necessary due to problems antic-ipated with some types of legacy MS when receiving (COMPLEMENTARY) frames in R-FACCH mode.
3. UA-frames are not allowed by the 3GPP-standard now, but a Change Request to allow R-FACCH on UA-frames might be issued in the future. UA-frames of LAPDm protocol are sent as Unnumbered Acknowledgement i.e. they are used to send response to commands delivered previously in S-frames (Supervisory) frames.
Validity Range
Default ValueNone.
Contained in the following commands: GET BTS
ASCICIPHenableCiphForASCI
The attribute enableCiphForASCI indicates whether ciphering for VGCS (Voice Group Call Service) is
enabled or disabled. VGCS ciphering allows to offer a secured path on the radio inter-face for mobiles engaged in point to multipoint connections, as it was already possible for the point to point calls.
Validity Range
TRUE
FALSE
TRUE
578DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805b2e2f
a
Default ValueNone.
Contained in the following commands: GET BTS
ASEVassociatedSeverity
The attribute allows the operator to define a specific severity for the failure event report related to a envaBTSE instance (site input).
The severity of alarm database is used (DEFAULT_DB) as default value.
Validity Range
Default Value
Contained in the following commands: CREATE ENVABTSE, GET ENVABTSE
ASTadministrativeState
This attribute indicates whether the management services have permitted or prohibited the use of the resource.
Validity Range
Default Value Locked for functional objects
Unlocked for equipment objects
Contained in the following commands: GET ACDCP, GET ACT, GET BATTERY, GET BCOM, GET BPORT, GET BTS, GET BTSEP NOSWL, GET BTSM NOSWL, GET CESPW, GET CESTUNNEL, GET CHAN, GET COBA, GET COBAETHINTF, GET COSA, GET CU, GET DIDCTMA,
FALSE
CRITICAL
MAJOR
MINOR
DEFAULT_DB
DEFAULT_DB
Locked
Unlocked
ShuttingDown
DN0933412 Issue 01579
BTSplus mainline commands at the Flexi BSC product family
a
Id:0900d805805b2e2f
GET DILNA, GET DUAMCO, GET DUDCTMA, GET DULNA, GET DUVSWR, GET ENVABTSE, GET ETHCON, GET ETHPORT, GET F6DCTMA, GET F6LNA, GET F6TNFP, GET F6VSWRP, GET FANP, GET FCUMAIN, GET FCUTR, GET FTNFP, GET FVSWRP, GET LAPDLE, GET RACK, GET SYNCBTSE, GET TMA, GET TRX, GET XCONNECT
ASTRINGassociatedString
This attribute allows the operator to define a specific text string for the failure event report related to an environmental alarm. It will be put into the information element "addi-tional text" of the failure event report. In case of hh=04 a specific string (##ACDC_FAULT) can be used to indicate that the support of emergency configuration in case of e.g. third party battery backup units is derived from the corresponding envaBTSE instance.
The ASCII characters are not terminated by a NULL character.
Validity Range
Default Value
Contained in the following commands: CREATE ENVABTSE, GET ENVABTSE
ASUBLKSATsAsubLinkSatellited
This attribute informs the BTSE SW about the presence of a satellite on the Asub inter-face.
Validity Range
Default Value terrestrialConnection
Contained in the following commands: GET BTSM NOSWL
AVSavailabilityStatus
0..26 characters string
""
terrestrialConnection
satelliteConnection
580DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805b2e2f
a
This attribute elaborates the Operational state and gives detailed information about the actions that occur.
Validity Range
Default Value Not Installed for equipment objects
Off line for TRX
NULL value for BTS / CHAN / BTSM
Contained in the following commands: GET ACDCP, GET ACT, GET BATTERY, GET BCOM, GET BPORT, GET BTS, GET BTSEP NOSWL, GET BTSM NOSWL, GET CESPW, GET CESTUNNEL, GET CHAN, GET COBA, GET COBAETHINTF, GET COSA, GET CU, GET DIDCTMA, GET DILNA, GET DUAMCO, GET DUDCTMA, GET DULNA, GET DUVSWR, GET ENVABTSE, GET ETHCON, GET ETHPORT, GET F6DCTMA, GET F6LNA, GET F6TNFP, GET F6VSWRP, GET FANP, GET FCUMAIN, GET FCUTR, GET FTNFP, GET FVSWRP, GET LAPDLE, GET RACK, GET SYNCBTSE, GET TMA, GET TRX, GET XCONNECT
1 to 6 items of
InTest
Failed
PowerOff
OffLine
OffDuty
Dependency
Degraded
NotInstalled
NULL
DN0933412 Issue 01581
BTSplus mainline commands at the Flexi BSC product family
b
Id:0900d805805b2e31
b
BATTCAPbatteryCapacity(*5Ah)
This attribute contains the value of the actual capacity of the installed battery in units of 5 Ah. The attribute reflects the setting of the DIP switch on the ACDCP controller board.
The value 0 corresponds to no battery backup.
The value 255 corresponds to battery backup 1275 Ah.
Note: The value 'no battery backup (0 Ah)' for a created object 'BATTERY' means that the operational state of the object will be "disabled". All other values result in the opera-tional state "enabled".
Validity Range
Default ValueNone.
Contained in the following commands: GET BATTERY
BCCHFREQbcchFrequency
0 - 255
<NULL>
This attribute is used for the objects BTS and ADJC and ADJCUMTS. It contains the absolute radio frequency channel number of the BCCH channel. It is identical to the GSM attribute BCCH ARFCN.
cellAllocationNum-ber
Hex Decimal
GSM900 "BB900" 0001 ... 007C 1 ... 124
GSM EXTENDED "F2ONLY900"
0000 ... 007C
03CF ... 03FF
0 ... 124
975 ... 1023
GSM EXTENDED REDUCED "EXT900"
0000 ... 007C
03CF ... 03FF
0 ... 124
975 ... 1023
DCS 1800 "DCS1800"
0200 ... 0375 512 ... 885
PCS 1900 0200 ... 032A 512 ... 810
GSM-R 03BB ... 03CE 955 ... 974
582DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805b2e31
b
Validity Range
Default ValueNone.
Contained in the following commands: GET BTS
BCOMTYPEbcomType
The attribute specifies the BCOM type. It is highly recommended to set this attribute to the correct value in order to ensure software checks for a consistent wiring in terms of the number of carrier units which can be wired to the BCOM.
It is under the user’ s responsibility to configure the correct value because the system cannot check if the value fits to the equipped hardware.
Validity Range
Default Value
Contained in the following commands: CREATE BCOM, GET BCOM, SET BCOM
GSM-DCS 0000 ... 007C
03CF ... 03FF
0200 ... 0375
0 ... 124
975 ... 1023
512 ... 885
GSM850 0080 ... 00FB 128 ... 251
GSM850-PCS 0080 ... 00FB
0200 ... 032A
128 ... 251
512 ... 810
GSM850-DCS 0080 ... 00FB
0200 ... 0375
128 ... 251
512 ... 885
0 - 1023
SixToSix
TwelveToSix
SixToSixMDUX
TwelveToSixMDUX
TwelveToSixCOAMCO
NotSet
NotSet
DN0933412 Issue 01583
BTSplus mainline commands at the Flexi BSC product family
b
Id:0900d805805b2e31
BCPBLboardCapability
This attribute returns the amount of configurable BPort interfaces on the related COBA board.
Validity Range
Default ValueNone.
Contained in the following commands: GET COBA
BERTbitErrorRateThreshold
This attribute defines thresholds allowed for a PCM30 or PCM24 line. The Bit Error Rate is estimated using code violation counters. The specified thresholds influence the setting of the corresponding status bits of the attribute 'lineStatusIndication'. When the lower or upper threshold is reached, a failure event report is sent. Reaching the upper threshold in a loop configuration triggers a direction switch.
g The values indicated as 'GET only' are values which were stored in a previous release in the BTSE flash eprom when these values were still allowed in a SET command.
Validity RangeIn commands CREATE BPORT, SET BPORT:
In commands GET BPORT:
twoAbisLines
fourAbisLines
ces
<NULL>
lowerThreshold E10_3
E10_4
...
E10_9
upperThreshold E10_3
E10_4
E10_5
lowerThreshold E10_0
E10_1
...
584DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805b2e31
b
Default ValueIn moc(s) BPORT:
None.
In moc(s) BPORT:
Contained in the following commands: CREATE BPORT, GET BPORT, SET BPORT
BMWD<x>beamWidth<x>(degree)
Attribute data provided by TMA.
Validity Range
Default ValueNone.
Contained in the following commands: GET TMA
BND<x>band<x>
Attribute data provided by TMA.
Validity Range
E10_9
upperThreshold E10_0
E10_1
...
E10_5
lowerThreshold E10_5
upperThreshold E10_3
0 - 65535
<NULL>
operating_band_I
operating_band_II
operating_band_III
operating_band_IV
operating_band_V
operating_band_VI
DN0933412 Issue 01585
BTSplus mainline commands at the Flexi BSC product family
b
Id:0900d805805b2e31
Default ValueNone.
Contained in the following commands: GET TMA
BSICbsIdentityCode
This attribute contains the Base Transceiver Station Identity Code (BSIC), which is transmitted on the SCH and used for identifying a BTSplus mainline. The BSIC consists of the Network Colour Code (NCC) and the Base Station Colour Code (BCC).
Validity Range
Default ValueNone.
Contained in the following commands: GET BTS
BSWVERbootSoftwareVersion
This attribute defines the firmware item code number. It can be read from the Boot EPROM of each processor module. The values for this attribute are identical with the SW image format (file ID and version) used in the swLoad-header-file. (exception: two bootSoftwareVersions for the TPU) or 'Not Existing' for Modules that are not equipped with a processor.
Each single field of the validity range has the following meaning.
bootSWfield 'BTBrrrhh.SWI', where:
rr BCX for COBA
BIX for CU
hh identical with the corresponding part of the bootSWversion
bootSwVersion 'cn-hh-vv-ii-ss-pp_yy-mm-dd, where:
cn Version part (network operator code)
hh Version part (HW/SW compatibility code)
vv Version part (feature package code)
operating_band_VII
operating_band_VIII
operating_band_IX
<NULL>
BCC 0 - 7
NCC 0 - 7
586DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805b2e31
b
ii Version part (sub-feature package code)
ss Version part (actual state)
pp Patch version (usually 00)
yy-mm-dd Production date (optional)
Validity Range
Default ValueNone.
Contained in the following commands: GET COBA, GET CU, GET FCUMAIN
BTSIDbaseStationId
Attribute data provided by TMA.
Validity Range
Default ValueNone.
Contained in the following commands: GET TMA
BTSISHOPbtsIsHopping
This attribute indicates whether the BTSplus mainline uses frequency hopping or not.
FALSE = Indicates that none of the channels in the BTS hops from the O&M point of view; from radio signalling point of view this can mean either that there is really no hopping at all or that there is hopping over a single frequency.
TRUE = Means that hopping is specified on a per channel basis.
Validity Range
Default Value FALSE
Contained in the following commands: GET BTS
39..39 characters string
0..32 characters string
TRUE
FALSE
DN0933412 Issue 01587
BTSplus mainline commands at the Flexi BSC product family
b
Id:0900d805805b2e31
BTSOBJIDbtsObjectId
The BTS object id is used in Flexi BSC product family MML for the BTS object. Within the BTS, the value is only used for display purposes in the BTS manager (LMT Evolu-tion).
Validity Range
Default ValueNone.
Contained in the following commands: GET BTS
BURNOFFSburstNumberOffset
This attribute allows to adjust the burst number offset for a cell. Equal burst number offsets result in synchronized TDMA frames.
This attribute is only meaningful if the enableInterSiteSync attribute is set to 'TRUE'.
Validity Range
Default Value 0
Contained in the following commands: GET BTS
1 - 3000
0 - 7
588DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805b2e33
c
c
CCPBLcarrierCapability
This attribute describes the call processing capabilities of the CU and FCUTR.
- In case of CU the attribute value is derived from the ESN/PID value of the CU.
- In case of FCUTR the attribute value depends on the istance number and the fcuMode of the corrisponding FCUMAIN object.
The attribute is read-only from the Abis/LMT Evolution point of view (GET CU/ GET FCUTR). After creation in advance of a CU/FCUTR object the attribute has the value "unknown" in case of hh-ii =04-01.
The BTSE SW maps the values of the attribute carrierCapability to the values of the attri-bute trxCapability
In case of FCUTR object, the validity range is:
- unknown
- edge
- edgeFourRXdiv
- in case of FCUTR both the values 'edge' and 'edgeFourRXdiv' are mapped to 'trxCa-pability=edge'.
Validity RangeIn commands GET CU:
In commands GET FCUTR:
Default ValueNone.
Contained in the following commands: GET CU, GET FCUTR
CELLNOcellNumber
unknown
gsm
edge
unknown
edge
edgeFourRxDiv
DN0933412 Issue 01589
BTSplus mainline commands at the Flexi BSC product family
c
Id:0900d805805b2e33
This attribute indicates the cell number to which a HW object for the antenna combining (DILNA, DULNA, DUVSWR, FTNFP, FVSWRP) is related to. It allows to have more than one antenna combining object in a cell.
Validity Range
Default ValueNone.
Contained in the following commands: CREATE DILNA, CREATE DULNA, CREATE DUVSWR, CREATE F6LNA, CREATE F6VSWRP, CREATE FTNFP, CREATE FVSWRP, GET DILNA, GET DULNA, GET DUVSWR, GET F6LNA, GET F6VSWRP, GET FTNFP, GET FVSWRP
CELLTYPEcellType
This attribute indicates the type of cell. It is used by BTSE for compatibility checks of the HW of a cell.
Validity Range
Default ValueNone.
Contained in the following commands: GET BTS
CHIDTchangeOnIDT
This attribute indicates a potential change of the IDTwF file. Whenever the IDFwF file was uploaded by the Flexi BSC product family the value is set to 'no change on IDT'. If a change of objects and attributes with relation to the IDT file occurs the value is set to 'IDT was changed'. If a local download of IDT data is done the value must be set manually to 'IDT was changed'.
Validity Range
Default Value IDTWasChanged
0 - 11
STDCELL
EXTCELL
DBSTDCELL
noChangeOnIDT
IDTWasChanged
590DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805b2e33
c
Contained in the following commands: GET BTSEP NOSWL, SET BTSEP
CHTYPEchannelCombination
This attribute defines the logical channel combination mapped onto the physical channel (timeslot).Changing or setting this attribute means a temporary loss of service for the whole TRX.
00 TCHFULL: TCH/F + FACCH/F + SACCH/TF
03 SDCCH: SDCCH/8 + SACCH/C8 Note 3
04 MAINB-CCH:
FCCH + SCH + BCCH + CCCH Note 4
05 MBCCHC: FCCH + SCH + BCCH + CCCH +SDCCH/4 + SACCH/C4
Note 4
06 CCCH: BCCH + CCCH Note 5
07 SCBCH: SDCCH/8 + SACCH/C8 + CBCH Note 1/6
08 BCBCH: FCCH + SCH + BCCH + CCCH + SDCCH/4 + SACCH/4 + CBCH
Note 1/7
09 TCHF_HLF:
TCH/H(0,1) + FACCH/H(0,1) + SACCH/TH (0,1) or TCH/F + FACCH/F + SACCH/TF
Note 2
0A TCHSD: TCH/H(0,1) + FACCH/H(0,1) + SACCH/TH (0,1) or TCH/F + FACCH/F + SACCH/TF or SDCCH/8 + SACCH/C8
Note 2/3
Note 1: These two channel combinations are created by replacing the logical channel SDCCH number 2 with the CBCH channel.
Note 2: The actual mode is decided on a per call basis.
Note 3: Not allowed for CHAN #0 of BCCH-TRX. Only allowed up to 3 times together with SDCCH/4 on BCCH-TRX. With no SDCCH/4 on the BCCH carrier up to four SDCCH/8 are allowed on the BCCH carrier. (For hh=04 this restriction may be dropped in a later release).
Note 4: Allowed only for CHAN #0 of BCCH-TRX.
Note 5: Allowed only for CHAN #2, #4, #6 of BCCH-TRX. Not allowed together with SDCCH/4.
Note 6: Allowed only for CHAN #0, #1, #2, #3. Not allowed for CHAN #0 of BCCH-TRX. Only one CBCH is allowed per cell.
DN0933412 Issue 01591
BTSplus mainline commands at the Flexi BSC product family
c
Id:0900d805805b2e33
Validity Range
Note 7: Only one CBCH is allowed per cell.
Note 8: The Flexi BSC product family checks guarantee that the first SDCCH/8 is created on the BCCH TRX and that a CBCH is allowed only on the BCCH TRX.
where:
TCH = Traffic Channel
FACCH = Fast Associated Control Channel
SACCH = Slow Associated Control Channel
/H = Half Rate
/F = Full Rate
FCCH = Frequency Correction Channel
SCH = Synchronization Channel
BCCH = Broadcast Control Channel
CCCH = Common Control Channel (CCCH = PCH + RACH + AGCH)
PCH = Paging Channel
RACH = Random Access Channel
AGCH = Access Grant Channel
CBCH = Cell Broadcast Channel
The SDCCH combinations for the BCCH-TRX can be summarized as follows:
1 MAIN BCCH + 4 SDCCH/8
1 MAIN BCCH COMBINED (SDCCH/4) + 3 SDCCH/8
1 MAIN BCCH + SCBCH (SDCCH/7) + 3 SDCCH/8
1 BCBCH (SDCCH/3) + 3 SDCCH/8
TCHFULL
SDCCH
MAINBCCH
MBCCHC
CCCH
SCBCH
BCBCH
TCHF_HLF
TCHSD
TCHSF
592DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805b2e33
c
Default ValueNone.
Contained in the following commands: GET CHAN
CLKACCclockAccuracy
This attribute indicates the accuracy of the clock.
Validity Range
Default ValueNone.
Contained in the following commands: GET SYNCBTSE
COMBMDcombMode
This attribute describes the combining mode of ACOM, DUVSWR (DUAMCO_VSRW), DULNA (DUAMCO_LNA) and DILNA(DIAMCO_LNA) . The "n:m" values listed below have the meaning "n RF inputs are combined to m RF output(s) by the ACOM, DUAMCO/FDUAMCO or DIAMCO board ". The values are not checked by BTSE appli-cations, the values are only stored for the convenience of the operator.
Validity RangeIn commands CREATE DILNA, GET DILNA:
In commands CREATE DULNA, CREATE DUVSWR, GET DULNA, GET DUVSWR:
Default ValueIn moc(s) DULNA, DUVSWR:
high
medium
low
phase
EightToTwo
OneToOne
TwoToOne
TwoToTwo
FourToTwo
EightToTwo
TwoToOneCOAMCO8
DN0933412 Issue 01593
BTSplus mainline commands at the Flexi BSC product family
c
Id:0900d805805b2e33
None.
In moc(s) DILNA:
Contained in the following commands: CREATE DILNA, CREATE DULNA, CREATE DUVSWR, GET DILNA, GET DULNA, GET DUVSWR
CUCONFcarrierUnitConfiguration
Validity Range
Default Value homogeneous
Contained in the following commands: GET BTS
CUWIRINGcuWiring
EightToTwo
This attributes describes, if in a cell a homogeneous configuration of carrier units is present (default value) or if one of the defined excep-tions is configured.
The following configurations are defined:
- CU_FlexCU_BS82II: This value has to be set if the cell is served by a BS82II and has an inhomogeneous carrier unit configuration with FlexCU and CU/ECU/GCU.
- CU_ECU_DCSPCS: This value has to be set if the cell has an inhomogeneous carrier unit configuration with old 1800/1900 MHz CUs (45.3 dBm output power) and ECU V2/3/3a of the same frequency band. This value replaces the former setting of the CU attribute maxGMSKOutputPower to dBm46_3.
- homogeneous: This value has to be set if the carrier unit con-figuration is homogeneous or shall be considered as homoge-neous. All carrier units use the maximum output power, which is provided by the hardware. No adaptation of the output power is performed. This implies, that output power differ-ences greater than 2 dB will be accepted. This setting corre-sponds to the current system behaviour.
homogenous
CU_FlexCU_BS82II
CU_ECU_DCSPCS
594DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805b2e33
c
The attribute describes the Tx and Rx wiring of the CU to the combining equipment. The attribute identifier cannot be present in the listOfRequiredAttributes together with other attribute identifiers; the attribute is not sent by the BTSE if a "Get CU" is done without the information element listOfRequiredAttributes.
Below are indicated some details about the validity range.
choice tag:
1 '0-3 optional subfields of fixed length follow (length=4-16)
txWiringPresence: (present only if choice tag is 1)
1 the next 4 bytes contain object class & instance of the object wired to the TX output
0 object class & instance don't follow
rxNWiringPresence: (present only if choice tag is 1, Octet position is variable)
1 the next 4 bytes contain object class & instance of the object wired to the RX output N
0 object class & instance don't follow
rxDWiringPresence: (present only if choice tag is 1, Octet position is variable)
1 the next 4 bytes contain object class & instance of the object wired to the RX output D
0 object class & instance don't follow
Validity Range
Default ValueNone.
Contained in the following commands: GET CU WIRING
<ANY>
DN0933412 Issue 01595
BTSplus mainline commands at the Flexi BSC product family
d
Id:0900d805805b11ae
d
DESTDIRdestinationDir
Validity Range
Default ValueNone.
Contained in the following commands: UPLBTSLOG SOFTWARE-MANAGEMENT, UPLLIDF REMINV
DLTESTFREQdlTestFrequency
This attribute defines the transmit frequency (ARFCN value) if the downlink interference analysis mode is enabled.
Validity Range
Default ValueNone.
Contained in the following commands: GET TRX
DMACFHSYIDdmaCFHSyId
This attribute is used for distinguishing DMA-enabled TRXs, which are operating on dif-ferent frequency bands or at different subbands in the same cell.
Validity Range
Destination directory
This attribute specifies the directory on the LMT Evolution hard disk where the BTSE alarm buffer sw will be copied (UPLBTSLOG).
This attribute specifies the directory on the LMT Evolution hard disk where the IDT file will be copied (UPLLIDF).
1..80 characters string
<ANY>
usedOnCFHSY0
usedOnCFHSY1
596DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805b11ae
d
Default Value DMA not used on TRX
Contained in the following commands: GET TRX
DMCFWIDduamcoFwId
This attribute provides information of the file ID and the FW version that is active on a MFDUAMCO board.
Validity Range
Default ValueNone.
Contained in the following commands:GET DUAMCO
DTMHOMTIMERhoDTMTimer(SACCH_multiframe_480/470ms)
This attribute determines whether handover due to DTM(Dual Transfer Mode) power budget is enabled.
This attribute is only relevant if inter-cell handover is enabled in the cell (see attribute enableInterCellHO).
DTM Power budget handover means: handover to another cell if this cell offers a higher transmission level. No matter if the power level of the actual cell is above the minimum or not.
Validity Range
Default ValueNone.
Contained in the following commands: GET BTS
DYNPOOLINFOdynamicPoolInfo
This attribute manages the dynamic allocation of traffic channels for EDGE and GPRS traffic. A timeslot from a dynamic pool is allocated only when the Abis resource (corre-
notUsed
39..39 characters string
1 - 21
DN0933412 Issue 01597
BTSplus mainline commands at the Flexi BSC product family
d
Id:0900d805805b11ae
sponding fixed Abis timeslots) associated with a given radio timeslot cannot any longer provide bandwidth required for transmission rates of GPRS/EDGE traffic. StartTsl and endTsl values are set to Null when the EDAP feature is disabled.
Validity Range
PortNumber PORT0
PORT1
PORT2
PORT3
PORT4
PORT5
PORT6
BPORT7
Null
startTsl TSL_01
TSL_02
TSL_03
TSL_04
TSL_05
TSL_06
TSL_07
TSL_08
TSL_09
TSL_10
TSL_11
TSL_12
TSL_13
TSL_14
TSL_15
TSL_16
TSL_17
TSL_18
TSL_19
TSL_20
TSL_21
TSL_22
TSL_23
TSL_24
598DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805b11ae
d
TSL_25
TSL_26
TSL_27
TSL_28
TSL_29
TSL_30
TSL_31
Null
endTsl TSL_01
TSL_02
TSL_03
TSL_04
TSL_05
TSL_06
TSL_07
TSL_08
TSL_09
TSL_10
TSL_11
TSL_12
TSL_13
TSL_14
TSL_15
TSL_16
TSL_17
TSL_18
TSL_19
TSL_20
TSL_21
TSL_22
TSL_23
TSL_24
TSL_25
TSL_26
TSL_27
TSL_28
DN0933412 Issue 01599
BTSplus mainline commands at the Flexi BSC product family
d
Id:0900d805805b11ae
Default ValueNone.
Contained in the following commands:GET TRX
DYNTRACGRANdynTraceGranularity
dynTraceGranularity is an attribute of the BTSM and specifies the granularity (multiples of SACCH reporting period) in which the TRACE MEASUREMENT RESULT messages are transmitted on the Abis interface in case the trace is activated. A value of N means that every N-th message is transmitted. The trace is activated per channel via the acknowledged message START TRACE. The trace is stopped via the acknowledged message STOP TRACE on the radio signalling link; it is stopped also implicitly at a release of the channel.
Validity RangeThe validity range is indicated in number of "SACCH multiframes".
Default Value1
Contained in the following commands:GET BTSM NOSWL
TSL_29
TSL_30
TSL_31
Null
1 - 254
600DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805b11b0
e
e
EACenableAc
This attribute determines, whether Admission Control evaluation must be performed. A change of the attribute becomes effective in the next AC period.
(TRUE = AC evaluation enabled)
Validity Range
Default Value FALSE (AC evaluation disabled)
Contained in the following commands: GET BTS
EANTHOPenableAntennaHopping
This attribute indicates whether Antenna Hopping is enabled or disabled for BTS. All TRX which are not connected to FICOM will hop.
A change of the attribute becomes effective with starting time algorithm handled inter-nally by the BTSE.
TRUE = enabled
Validity Range
Default Value FALSE (disabled)
Contained in the following commands: GET BTS
EAUTONEGenableAutoNegotiation
The attribute indicates whether the Ethernet auto negotiation for speed, duplex mode and optionally flow control is enabled for the instance of an Ethernet port.
If auto negotiation is disabled the speed will be set to 100M and duplex mode will be enabled. Also in case when this attribute is set to TRUE there will be propagated only
TRUE
FALSE
TRUE
FALSE
DN0933412 Issue 01601
BTSplus mainline commands at the Flexi BSC product family
e
Id:0900d805805b11b0
100M and duplex mode. If the peer Ethernet device cannot provide 100M Duplex mode, then the link remains down. Only FlowControl is really negotiated according to the setting of the attribute "enableFlowControl".
AutoNegotiation is only relevant for electrical Ethernet interfaces.
Validity Range
Default Value
Contained in the following commands: CREATE ETHPORT, GET ETHPORT, SET ETHPORT
EAUTORECenableAutoRecovery
This attribute indicates whether an automatic recovery is enabled or disabled. Prerequi-sites for an automatic recovery in case the feature is enabled are the following:
• HW-Reset cause is "Power-On" • The board is disabled.failed.unlocked
Validity Range
Default Value disabled
Contained in the following commands: GET BTSEP NOSWL, SET BTSEP
EEOTDenableEOTD
This attribute indicates if the Location Services (LCS) positioning method 'Enhanced Observed Time dufference' (EOTD) is being used.
(TRUE = enabled)
Validity Range
Default Value FALSE (disabled)
TRUE
FALSE
TRUE
disabled
enabled
TRUE
FALSE
602DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805b11b0
e
Contained in the following commands: GET BTS
EEXCDISTenableExcessiveDistance
This attribute indicates whether the sending of call release is enabled/disabled when the distance between the MS and the BTSplus mainline exceeds the excessive distance.
TRUE = enabled
Validity Range
Default Value TRUE (enabled)
Contained in the following commands: GET BTS
EFCUSUPenableFcuSupport
FALSE
TRUE
For a COB4P12, 'TRUE' is the only possible value and will be assigned by the BTSE-software in case no value is provided by the operator; the attribute value 'TRUE' cannot be changed by the oper-ator.
For COBA2P8 both values are possible.
ý 'FALSE' will be assigned by the BTSE-software in case no value is provided by the operator. In this case the BTSE handles up to 24 CU boards (distributed to rack 0-2). If enableFcuSupport is set to 'FALSE', the creation of the objects FCUMAIN / FCUTR is possible but any created objects FCUMAIN / FCUTR will remain in state: oper-ationalState 'DISABLED', availabilityStatus 'Not Installed'.
ý 'TRUE' means that the BTSE can handle only up to 12 boards. Within these 12 boards (allowed only in base rack in case of BTS240XL, respectively allowed only in base rack and the first 4 instances of 1st extension-rack in case of BTS240 distributed to rack 0-2) any mix of CU boards and FlexCU boards (modeled as FCUMAIN and FCUTR objects) is possible.
--> The creation of any boards (CU or FlexCU) will be answered with a NACK by the BTSE, if:
- typeofBTSE is BS240XL and the board to be created is in the extension rack
DN0933412 Issue 01603
BTSplus mainline commands at the Flexi BSC product family
e
Id:0900d805805b11b0
The value FALSE in the validity range means:
support of FLEXCU disabled
The value TRUE in the validity range means:
support of FLEXCU enabled
Validity Range
Default ValueNone.
Contained in the following commands: CREATE COBA, GET COBA, SET COBA
EFLWCTRLenableFlowControl
The attribute enables the Ethernet flow control. Flow control requires full duplex opera-tion. Received Ethernet PAUSE frames are ignored if set to â??falseâ??.
The following attribute is relevant: enableAutonegotiation
Validity Range
Default Value
- typeofBTSE is BS240 and the board to be created is in the 1st extension rack and would have an instance number greater 3, or is in the 2nd extension rack.
A change of the attribute value is possible only on a COBA2P8 and causes a reset of the BTSE. In LMTphase 3 a change of the attribute value is allowed only if the administrativeState of BTSM is 'Locked'.
--> The BTSE SW will answer with a NACK if the operator tries to set the attribute to 'TRUE' if:
- typeofBTSE is BS240XL and a board (FlexCU or CU) is created in an extension rack
- typeofBTSE is BS240 and a FlexCU or CU with an instance greater than 3 is created in 1st extension rack or any instance is created in 2nd extension rack.
TRUE
FALSE
TRUE
FALSE
FALSE
604DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805b11b0
e
Contained in the following commands: CREATE ETHPORT, GET ETHPORT, SET ETHPORT
EINTSITSYNenableInterSiteSync
The attribute enableInterSiteSync allows to disable or enable the inter site synchroniza-tion.
If intersite synchronisation is enabled, the attributes burstNumberOffset and frameNum-berOffset attributes related to the BTS object become effective. As a result different transceivers of the same BTSE may have asynchronous frame and burst numbers.
TRUE = enabled
Validity Range
Default Value FALSE (disabled)
Contained in the following commands: GET BTSM NOSWL
EMT1emergencyTimer1(min)
This attribute specifies after which time (minutes) the BTSE will be switched to an emer-gency configuration if a "battery backup operation" (due to "mains breakdown") occurs. The switch includes the power-down of TRX related equipment.
BS241: emerg. timer starts if first ACDC fails.
(step size 1 minute)
Validity Range
Default Value 10 minutes
Contained in the following commands: GET BTSM NOSWL
EMT2emergencyTimer2(min)
This attribute specifies after which time (minutes) the BTSE will be switched to a zero carrier configuration if a switch to emergency configuration has been performed due to a "battery backup operation". The switch includes the power-down of TRX related equip-
TRUE
FALSE
0 - 1400
DN0933412 Issue 01605
BTSplus mainline commands at the Flexi BSC product family
e
Id:0900d805805b11b0
ment. The value 0 means the emergencyTimer2 is not valid, i.e. the BTSE will not switch to a zero carrier configuration. For other values the zero carrier configuration will be reached after the sum of the times specified in emergencyTimer1 and emergencyTimer2.
Validity Range
Default Value 0 minutes
Contained in the following commands: GET BTSM NOSWL
ENTRIESentries
Validity Range Number of the requested Entries <1-65534>
Getting all Entries stored in the buffer 65535
For the upload of MIB_DATA_HW_STATES only the value 65535 is used.
For the upload of INVENTORY_DATA_TABLE, MIT and SCA the attribute has no meaning.
Default ValueNone.
Contained in the following commands: UPLBTSLOG SOFTWARE-MANAGEMENT
EQUPOSequipmentPosition
The attribute contains the room / row and rack number as 6 ASCII characters not termi-nated by a NUL character. The attribute should be set by the operator before a upload of the IDT is performed.
Validity Range
Default Value
0 - 1400
Number of entries
This attribute is used to indicate the number of the entries to be uploaded.
6..6 characters string
"010101"
606DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805b11b0
e
Contained in the following commands: GET BTSEP NOSWL, SET BTSEP
ERFACCHALPDMFenableRFacchOnAnyLapdmFrame
This attribute determines whether R-FACCH (Repeated FACCH) is enabled or disabled on cell basis for the specified codec type. Attribute is implemented as a bit map consist-ing of 6 bits, one bit per codec type.
Bitmap Codec Type Codec Type Description
0/1 TCH/AFS Narrow-band Adaptive Multi-Rate Full Rate Speech
0/1 TCH/EFS Enhanced Full Rate Speech
0/1 TCH/FS GSM Full Rate Speech
0/1 TCH/WFS Wide-band Adaptive Multi-Rate Full Rate Speech
0/1 TCH/AHS Narrow-band Adaptive Multi-Rate Half Rate Speech
0/1 TCH/HS GSM Half Rate Speech
Validity Range
NOT_SET
AFS
AHS
AFS_AHS
EFS
AFS_EFS
AHS_EFS
AFS_AHS_EFS
FS
AFS_FS
AHS_FS
AFS_AHS_FS
EFS_FS
AFS_EFS_FS
DN0933412 Issue 01607
BTSplus mainline commands at the Flexi BSC product family
e
Id:0900d805805b11b0
AHS_EFS_FS
AFS_AHS_EFS_FS
HS
AFS_HS
AHS_HS
AFS_AHS_HS
EFS_HS
AFS_EFS_HS
AHS_EFS_HS
AFS_AHS_EFS_HS
FS_HS
AFS_FS_HS
AHS_FS_HS
AFS_AHS_FS_HS
EFS_FS_HS
AFS_EFS_FS_HS
AHS_EFS_FS_HS
AFS_AHS_EFS_FS_HS
WFS
AFS_WFS
AHS_WFS
AFS_AHS_WFS
EFS_WFS
AFS_EFS_WFS
AHS_EFS_WFS
AFS_AHS_EFS_WFS
FS_WFS
AFS_FS_WFS
AHS_FS_WFS
AFS_AHS_FS_WFS
EFS_FS_WFS
AFS_EFS_FS_WFS
AHS_EFS_FS_WFS
AFS_AHS_EFS_FS_WFS
HS_WFS
AFS_HS_WFS
608DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805b11b0
e
Default ValueNone.
Contained in the following commands: GET BTS
ERFACCHCMDFenableRFacchOnCmdFrames
This attribute determines whether "DL Repeated FACCH" is enabled or disabled on a cell basis for those MS not having signaled their Repeated ACCH Capability as '1'. Those types of MS include legacy MS and new MS that have to signal their Repeated ACCH Capability as "0". To enable R-FACCH on LAPDm command frames for a certain codec in the cell, the name of that codec shall be entered in a list.
Validity Range
AHS_HS_WFS
AFS_AHS_HS_WFS
EFS_HS_WFS
AFS_EFS_HS_WFS
AHS_EFS_HS_WFS
AFS_AHS_EFS_HS_WFS
FS_HS_WFS
AFS_FS_HS_WFS
AHS_FS_HS_WFS
AFS_AHS_FS_HS_WFS
EFS_FS_HS_WFS
AFS_EFS_FS_HS_WFS
AHS_EFS_FS_HS_WFS
AFS_AHS_EFS_FS_HS_WFS
NOT_SET
AFS
AHS
AFS_AHS
EFS
AFS_EFS
AHS_EFS
AFS_AHS_EFS
FS
DN0933412 Issue 01609
BTSplus mainline commands at the Flexi BSC product family
e
Id:0900d805805b11b0
AFS_FS
AHS_FS
AFS_AHS_FS
EFS_FS
AFS_EFS_FS
AHS_EFS_FS
AFS_AHS_EFS_FS
HS
AFS_HS
AHS_HS
AFS_AHS_HS
EFS_HS
AFS_EFS_HS
AHS_EFS_HS
AFS_AHS_EFS_HS
FS_HS
AFS_FS_HS
AHS_FS_HS
AFS_AHS_FS_HS
EFS_FS_HS
AFS_EFS_FS_HS
AHS_EFS_FS_HS
AFS_AHS_EFS_FS_HS
WFS
AFS_WFS
AHS_WFS
AFS_AHS_WFS
EFS_WFS
AFS_EFS_WFS
AHS_EFS_WFS
AFS_AHS_EFS_WFS
FS_WFS
AFS_FS_WFS
AHS_FS_WFS
AFS_AHS_FS_WFS
EFS_FS_WFS
610DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805b11b0
e
Default ValueNone.
Contained in the following commands: GET BTS
ERSACCHDLenableRSacchDL
The attribute is implemented as a list of values representing combinations of signaling and allowed codec types and/or signaling. This list is present in Appendix. For the binary representation 0 means that R-SACCH in DL on a per cell basis is notapplied for spec-ified speech codec type and /or signaling. Value 1 means that R-SACCH in DL is applied for specified speech codec type and/or signaling. Value 0x00 has specific meaning and should be read as R-SACCH in DL is not applied for any speech codec type.
When enabling R-SACCH feature on the BTSplus mainline, where only old CUs are created, the SET command is acked but ignored locally.
Validity Range
AFS_EFS_FS_WFS
AHS_EFS_FS_WFS
AFS_AHS_EFS_FS_WFS
HS_WFS
AFS_HS_WFS
AHS_HS_WFS
AFS_AHS_HS_WFS
EFS_HS_WFS
AFS_EFS_HS_WFS
AHS_EFS_HS_WFS
AFS_AHS_EFS_HS_WFS
FS_HS_WFS
AFS_FS_HS_WFS
AHS_FS_HS_WFS
AFS_AHS_FS_HS_WFS
EFS_FS_HS_WFS
AFS_EFS_FS_HS_WFS
AHS_EFS_FS_HS_WFS
AFS_AHS_EFS_FS_HS_WFS
NOT_SET
AFS
DN0933412 Issue 01611
BTSplus mainline commands at the Flexi BSC product family
e
Id:0900d805805b11b0
AHS
AFS_AHS
EFS
AFS_EFS
AHS_EFS
AFS_AHS_EFS
FS
AFS_FS
AHS_FS
AFS_AHS_FS
EFS_FS
AFS_EFS_FS
AHS_EFS_FS
AFS_AHS_EFS_FS
HS
AFS_HS
AHS_HS
AFS_AHS_HS
EFS_HS
AFS_EFS_HS
AHS_EFS_HS
AFS_AHS_EFS_HS
FS_HS
AFS_FS_HS
AHS_FS_HS
AFS_AHS_FS_HS
EFS_FS_HS
AFS_EFS_FS_HS
AHS_EFS_FS_HS
AFS_AHS_EFS_FS_HS
WFS
AFS_WFS
AHS_WFS
AFS_AHS_WFS
EFS_WFS
AFS_EFS_WFS
612DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805b11b0
e
AHS_EFS_WFS
AFS_AHS_EFS_WFS
FS_WFS
AFS_FS_WFS
AHS_FS_WFS
AFS_AHS_FS_WFS
EFS_FS_WFS
AFS_EFS_FS_WFS
AHS_EFS_FS_WFS
AFS_AHS_EFS_FS_WFS
HS_WFS
AFS_HS_WFS
AHS_HS_WFS
AFS_AHS_HS_WFS
EFS_HS_WFS
AFS_EFS_HS_WFS
AHS_EFS_HS_WFS
AFS_AHS_EFS_HS_WFS
FS_HS_WFS
AFS_FS_HS_WFS
AHS_FS_HS_WFS
AFS_AHS_FS_HS_WFS
EFS_FS_HS_WFS
AFS_EFS_FS_HS_WFS
AHS_EFS_FS_HS_WFS
AFS_AHS_EFS_FS_HS_WFS
SIGNALING
AFS_SIGNALING
AHS_SIGNALING
AFS_AHS_SIGNALING
EFS_SIGNALING
AFS_EFS_SIGNALING
AHS_EFS_SIGNALING
AFS_AHS_EFS_SIGNALING
FS_SIGNALING
DN0933412 Issue 01613
BTSplus mainline commands at the Flexi BSC product family
e
Id:0900d805805b11b0
AFS_FS_SIGNALING
AHS_FS_SIGNALING
AFS_AHS_FS_SIGNALING
EFS_FS_SIGNALING
AFS_EFS_FS_SIGNALING
AHS_EFS_FS_SIGNALING
AFS_AHS_EFS_FS_SIGNALING
HS_SIGNALING
AFS_HS_SIGNALING
AHS_HS_SIGNALING
AFS_AHS_HS_SIGNALING
EFS_HS_SIGNALING
AFS_EFS_HS_SIGNALING
AHS_EFS_HS_SIGNALING
AFS_AHS_EFS_HS_SIGNALING
FS_HS_SIGNALING
AFS_FS_HS_SIGNALING
AHS_FS_HS_SIGNALING
AFS_AHS_FS_HS_SIGNALING
EFS_FS_HS_SIGNALING
AFS_EFS_FS_HS_SIGNALING
AHS_EFS_FS_HS_SIGNALING
AFS_AHS_EFS_FS_HS_SIGNALING
WFS_SIGNALING
AFS_WFS_SIGNALING
AHS_WFS_SIGNALING
AFS_AHS_WFS_SIGNALING
EFS_WFS_SIGNALING
614DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805b11b0
e
AFS_EFS_WFS_SIGNALING
AHS_EFS_WFS_SIGNALING
AFS_AHS_EFS_WFS_SIGNALING
FS_WFS_SIGNALING
AFS_FS_WFS_SIGNALING
AHS_FS_WFS_SIGNALING
AFS_AHS_FS_WFS_SIGNALING
EFS_FS_WFS_SIGNALING
AFS_EFS_FS_WFS_SIGNALING
AHS_EFS_FS_WFS_SIGNALING
AFS_AHS_EFS_FS_WFS_SIGNALING
HS_WFS_SIGNALING
AFS_HS_WFS_SIGNALING
AHS_HS_WFS_SIGNALING
AFS_AHS_HS_WFS_SIGNALING
EFS_HS_WFS_SIGNALING
AFS_EFS_HS_WFS_SIGNALING
AHS_EFS_HS_WFS_SIGNALING
AFS_AHS_EFS_HS_WFS_SIGNALING
FS_HS_WFS_SIGNALING
AFS_FS_HS_WFS_SIGNALING
AHS_FS_HS_WFS_SIGNALING
DN0933412 Issue 01615
BTSplus mainline commands at the Flexi BSC product family
e
Id:0900d805805b11b0
Default ValueNone.
Contained in the following commands: GET BTS
ERSACCHULenableRSacchUL
The attribute is implemented as a list of values representing combinations of signalin-gand allowed codec types and/or signaling. This list is present in Appendix. For the binary representation “0” means that R-SACCH in DL on a per cell basis is not applied for specified speech codec type and /or signaling. Value “1” means that RSACCH in DL is applied for specified speech codec type and/or signaling. Value 0x00 has specific meaning and should be read as R-SACCH in DL is not applied for any speech codec type.This attribute is used to enable the R-SACCH in UL feature on a per cell basis for different codec types and /or signaling only for MS with R-ACCH_CAP = 1.
When enabling the R-SACCH feature on the BTSplus mainline, where only old CUs are created, the SET command s acked but ignored locally.
Validity Range
AFS_AHS_FS_HS_WFS_SIGNALING
EFS_FS_HS_WFS_SIGNALING
AFS_EFS_FS_HS_WFS_SIGNALING
AHS_EFS_FS_HS_WFS_SIGNALING
AFS_AHS_EFS_FS_HS_WFS_SIGNALING
NOT_SET
AFS
AHS
AFS_AHS
EFS
AFS_EFS
AHS_EFS
AFS_AHS_EFS
FS
AFS_FS
AHS_FS
616DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805b11b0
e
AFS_AHS_FS
EFS_FS
AFS_EFS_FS
AHS_EFS_FS
AFS_AHS_EFS_FS
HS
AFS_HS
AHS_HS
AFS_AHS_HS
EFS_HS
AFS_EFS_HS
AHS_EFS_HS
AFS_AHS_EFS_HS
FS_HS
AFS_FS_HS
AHS_FS_HS
AFS_AHS_FS_HS
EFS_FS_HS
AFS_EFS_FS_HS
AHS_EFS_FS_HS
AFS_AHS_EFS_FS_HS
WFS
AFS_WFS
AHS_WFS
AFS_AHS_WFS
EFS_WFS
AFS_EFS_WFS
AHS_EFS_WFS
AFS_AHS_EFS_WFS
FS_WFS
AFS_FS_WFS
AHS_FS_WFS
AFS_AHS_FS_WFS
EFS_FS_WFS
AFS_EFS_FS_WFS
AHS_EFS_FS_WFS
DN0933412 Issue 01617
BTSplus mainline commands at the Flexi BSC product family
e
Id:0900d805805b11b0
AFS_AHS_EFS_FS_WFS
HS_WFS
AFS_HS_WFS
AHS_HS_WFS
AFS_AHS_HS_WFS
EFS_HS_WFS
AFS_EFS_HS_WFS
AHS_EFS_HS_WFS
AFS_AHS_EFS_HS_WFS
FS_HS_WFS
AFS_FS_HS_WFS
AHS_FS_HS_WFS
AFS_AHS_FS_HS_WFS
EFS_FS_HS_WFS
AFS_EFS_FS_HS_WFS
AHS_EFS_FS_HS_WFS
AFS_AHS_EFS_FS_HS_WFS
SIGNALING
AFS_SIGNALING
AHS_SIGNALING
AFS_AHS_SIGNALING
EFS_SIGNALING
AFS_EFS_SIGNALING
AHS_EFS_SIGNALING
AFS_AHS_EFS_SIGNALING
FS_SIGNALING
AFS_FS_SIGNALING
AHS_FS_SIGNALING
AFS_AHS_FS_SIGNALING
EFS_FS_SIGNALING
AFS_EFS_FS_SIGNALING
AHS_EFS_FS_SIGNALING
AFS_AHS_EFS_FS_SIGNALING
618DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805b11b0
e
HS_SIGNALING
AFS_HS_SIGNALING
AHS_HS_SIGNALING
AFS_AHS_HS_SIGNALING
EFS_HS_SIGNALING
AFS_EFS_HS_SIGNALING
AHS_EFS_HS_SIGNALING
AFS_AHS_EFS_HS_SIGNALING
FS_HS_SIGNALING
AFS_FS_HS_SIGNALING
AHS_FS_HS_SIGNALING
AFS_AHS_FS_HS_SIGNALING
EFS_FS_HS_SIGNALING
AFS_EFS_FS_HS_SIGNALING
AHS_EFS_FS_HS_SIGNALING
AFS_AHS_EFS_FS_HS_SIGNALING
WFS_SIGNALING
AFS_WFS_SIGNALING
AHS_WFS_SIGNALING
AFS_AHS_WFS_SIGNALING
EFS_WFS_SIGNALING
AFS_EFS_WFS_SIGNALING
AHS_EFS_WFS_SIGNALING
AFS_AHS_EFS_WFS_SIGNALING
FS_WFS_SIGNALING
AFS_FS_WFS_SIGNALING
DN0933412 Issue 01619
BTSplus mainline commands at the Flexi BSC product family
e
Id:0900d805805b11b0
AHS_FS_WFS_SIGNALING
AFS_AHS_FS_WFS_SIGNALING
EFS_FS_WFS_SIGNALING
AFS_EFS_FS_WFS_SIGNALING
AHS_EFS_FS_WFS_SIGNALING
AFS_AHS_EFS_FS_WFS_SIGNALING
HS_WFS_SIGNALING
AFS_HS_WFS_SIGNALING
AHS_HS_WFS_SIGNALING
AFS_AHS_HS_WFS_SIGNALING
EFS_HS_WFS_SIGNALING
AFS_EFS_HS_WFS_SIGNALING
AHS_EFS_HS_WFS_SIGNALING
AFS_AHS_EFS_HS_WFS_SIGNALING
FS_HS_WFS_SIGNALING
AFS_FS_HS_WFS_SIGNALING
AHS_FS_HS_WFS_SIGNALING
AFS_AHS_FS_HS_WFS_SIGNALING
EFS_FS_HS_WFS_SIGNALING
AFS_EFS_FS_HS_WFS_SIGNALING
AHS_EFS_FS_HS_WFS_SIGNALING
AFS_AHS_EFS_FS_HS_WFS_SIGNALING
620DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805b11b0
e
Default ValueNone.
Contained in the following commands: GET BTS
ETOPenableTOP
This attribute determines whether TOP(Temporary Overpower) is enabled or disabled on cell basis for the specified codec type. Attribute is implemented as a bit map consist-ing of 6 bits, one bit per codec type.
Validity Range
Bitmap
Codec Type Codec Type Description
0/1 TCH/AFS Narrow-band Adaptive Multi-Rate Full Rate Speech
0/1 TCH/EFS Enhanced Full Rate Speech
0/1 TCH/FS GSM Full Rate Speech
0/1 TCH/WFS Wide-band Adaptive Multi-Rate Full Rate Speech
0/1 TCH/AHS Narrow-band Adaptive Multi-Rate Half Rate Speech
0/1 TCH/HS GSM Half Rate Speech
NOT_SET
AFS
AHS
AFS_AHS
EFS
AFS_EFS
AHS_EFS
AFS_AHS_EFS
FS
AFS_FS
AHS_FS
AFS_AHS_FS
EFS_FS
AFS_EFS_FS
AHS_EFS_FS
AFS_AHS_EFS_FS
DN0933412 Issue 01621
BTSplus mainline commands at the Flexi BSC product family
e
Id:0900d805805b11b0
HS
AFS_HS
AHS_HS
AFS_AHS_HS
EFS_HS
AFS_EFS_HS
AHS_EFS_HS
AFS_AHS_EFS_HS
FS_HS
AFS_FS_HS
AHS_FS_HS
AFS_AHS_FS_HS
EFS_FS_HS
AFS_EFS_FS_HS
AHS_EFS_FS_HS
AFS_AHS_EFS_FS_HS
WFS
AFS_WFS
AHS_WFS
AFS_AHS_WFS
EFS_WFS
AFS_EFS_WFS
AHS_EFS_WFS
AFS_AHS_EFS_WFS
FS_WFS
AFS_FS_WFS
AHS_FS_WFS
AFS_AHS_FS_WFS
EFS_FS_WFS
AFS_EFS_FS_WFS
AHS_EFS_FS_WFS
AFS_AHS_EFS_FS_WFS
HS_WFS
AFS_HS_WFS
AHS_HS_WFS
AFS_AHS_HS_WFS
622DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805b11b0
e
Default ValueNone.
Contained in the following commands: GET BTS
ETXDIVTSenableTxDivTimeShift
The attribute indicates whether Tx Diversity Time Shift is enabled or disabled for a BTSplus mainline. As a consequence all TRXs of the cell will operate in "double-power/half capacity" Mode (called Coverage Mode) or in "normal-power/normal capac-ity" Mode (called Capacity Mode).
The value 'TRUE' means that all CUs or FCUTRs in the a cell operate as CU pairs or FCUTR pairs in a master slave mode. Pairs are defined as follows (k=0, 1, 2, etc.):
- A CU pair consists of the master CU (instance 2k) and the slave CU (instance 2k+1)
- A FCUTR pair consists of the master FCUTR (instance 2k) and the slave FCUTR (instance 2k+1).
The two members of each pair should be wired to different antennas of the same cell otherwise the combining loss would nullify the additional gain of the coverage mode. A change of the attribute becomes effective after reconfiguration of the cell handled inter-nally by the BTSE and causes a reset of the related CU or FCUMAIN objects. The BSC takes care that the BTS object is locked whenever the value of the attribute is changed.
Validity Range
EFS_HS_WFS
AFS_EFS_HS_WFS
AHS_EFS_HS_WFS
AFS_AHS_EFS_HS_WFS
FS_HS_WFS
AFS_FS_HS_WFS
AHS_FS_HS_WFS
AFS_AHS_FS_HS_WFS
EFS_FS_HS_WFS
AFS_EFS_FS_HS_WFS
AHS_EFS_FS_HS_WFS
AFS_AHS_EFS_FS_HS_WFS
TRUE
FALSE
DN0933412 Issue 01623
BTSplus mainline commands at the Flexi BSC product family
e
Id:0900d805805b11b0
Default Value FALSE (disabled)
Contained in the following commands: GET BTS
EVTYPeventType
This attribute specifies the type of failure event alarm.
Validity Range
Default ValueNone.
Contained in the following commands: GETACTIVEALARMS BTSEP
EXCDISTexcessiveDistance(km)
This attribute indicates the distance limit to be used for call release when the distance between the MS and the BTSplus mainline exceeds the excessiveDistance. Value indi-cating more 35 km are valid only for extended cells. A change of the attribute becomes effective in the next SACCH multiframe.
Validity Range
Default Value 100 Km
Contained in the following commands: GET BTS
COMMUNICATION_FAILURE_EVENT
QUAL_SERVICE_FAILURE_EVENT
PROCESSING_FAILURE_EVENT
EQUIPMENT_FAILURE_EVENT
ENVIRONMENTAL_FAILURE_EVENT
1 - 100
624DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805b11b0
e
EXTMODEextendedMode
This attribute indicates whether a channel instance operates in the extended mode (usage of two radio timeslots) which is needed for extended cells. The value TRUE is allowed only for even channel instances. Before an even channel instance N can be created with the value TRUE for the extendedMode it must be guaranteed that channel instance N+1 does not exist.
Validity Range
Default Value FALSE
Contained in the following commands: GET CHAN
TRUE
FALSE
DN0933412 Issue 01625
BTSplus mainline commands at the Flexi BSC product family
f
Id:0900d805805ca0eb
f
F6FWIDficom6FwId
This attribute provides information of the “file ID” and the “FW version” that is active on a FICOM6 board.
Validity Range
Default ValueNone.
Contained in the following commands:GET F6VSWRP
FACCHQfacchQual
This attribute defines the number of FACCH (stealing flags minus 1) to be received for detecting a FACCH frame.
(step size 1 FACCH frame)
Validity Range
Default Value 5
Contained in the following commands:GET BTS
FACHBTfachBusyThreshold(dBm)
This attribute defines a threshold for the received signal level during handover proce-dure when mobile station transmits HANDOVER ACCESS or ASCI uplink access burst message on the FACCH (Fast Associated Control Channel). A signal exceeding this threshold is interpreted as a busy FACCH.
Validity Range
Default ValueNone.
39..39 characters string
0 - 7
<ANY>
626DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805ca0eb
f
Contained in the following commands:GET BTS
FBANDfrequencyBand
The attribute specifies the frequency band of the BCOM. It is highly recommended to set this attribute to the correct value in order to ensure software checks for a consistent wiring especially in case of dual band configurations.
The user must configure the correct value because the system cannot check if the value fits to the equipped hardware.
Validity Range
Default Value
Contained in the following commands:CREATE BCOM, GET BCOM, SET BCOM
FCUMAINWIRINGfcumainWiring
The attribute describes the Tx and Rx wiring of the FlexCU board to the combining equipment. The attribute identifier cannot be present in the listOfRequiredAttributes together with other attribute identifiers and it is not sent by the BTSE object if a "Get FCUMAIN" is done without the information element listOfRequiredAttributes.
The attribute is not visible at the RC.
Validity Range choice tag
1 = 'variable'
tx0WiringPresence:
1 = the next 4 bytes contain object class & instance of the object wired to the TX output 0
0 = object class & instance don't follow
rxNWiringPresence: Octect position is variable
Gsm850
Gsm900
Dcs1800
Pcs1900
NotSet
NotSet
DN0933412 Issue 01627
BTSplus mainline commands at the Flexi BSC product family
f
Id:0900d805805ca0eb
1 = the next 4 bytes contain object class & instance of the object wired to the RX output N
0 = object class & instance don't follow
rxDWiringPresence: Octect position is variable
1 = the next 4 bytes contain object class & instance of the object wired to the RX output D
0 = object class & instance don't follow
tx1WiringPresence: Octect position is variable
1 = the next 4 bytes contain object class & instance of the object wired to the TX output 1
0 = object class & instance don't follow
rxN1WiringPresence: Octect position is variable
1 = the next 4 bytes contain object class & instance of the object wired to the RX output N1
0 = object class & instance don't follow
rxD1WiringPresence: Octect position is variable
1 = the next 4 bytes contain object class & instance of the object wired to the RX output D1
0 = object class & instance don't follow
Default ValueNone.
Contained in the following commands:GET FCUMAIN WIRING
FCUMODEfcuMode
This attribute specifies in which mode a FlexCU board shall operate.
A FlexCU in 'singleCUMode' has the following characteristics:
• Does not allow the creation of the odd instance of the FCUTRobject • Does not support the feature 'TX diversity time shift'. If thevalue of the attribute
'enableTxDivTimeShift' is 'TRUE', anappropriate FCUMAIN alarm is emitted and the FCUMAINand FCUTR instance are set to disabled
• Supports only 1 TRX with up to 4 RX branches
A FlexCU board in 'doubleCUMode' supports up to 2 TRX instances:
• Support of two TRX instances ('enableTxDivTimeShift' is'FALSE' • Support of 1 TRX with 'TX diversity time shift' ('enableTxDiv-TimeShift' is 'TRUE')
628DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805ca0eb
f
Validity Range
Default Value doubleCUMode
Contained in the following commands:CREATE FCUMAIN, GET FCUMAIN
FILEfile
This attribute specifies the file within the destinationDirectory on the LMT Evolution hard disk where the alarm buffer sw will be copied (UPLBTSLOG) or where the IDT file will be copied (UPLLIDF).
Validity Range
Default ValueNone.
Contained in the following commands:UPLBTSLOG SOFTWARE-MANAGEMENT, UPLLIDF REMINV
FILEFWVfwVersion
This attribute states the name and version of the fwImage file. The file is transferred to the dedicated board to perform the FW upgrade.
Validity Range
Default ValueNone.
Contained in the following commands:FWUPGRADE BTSM
FILEIDfileId
singleCUMode
doubleCUMode
1..30 characters string
26..26 characters string
DN0933412 Issue 01629
BTSplus mainline commands at the Flexi BSC product family
f
Id:0900d805805ca0eb
g This value may only be used in conjunction with the FileVersion "00 " (indicating the destination "Easy-Disk").
Validity Range
Default ValueNone.
Contained in the following commands:ACTIVATE BTSM, ACTIVATE_DELAYED BTSM, FWUPGRADE BTSM
The FileId is a parameter used within the SW download procedures and not of the type 'GET'. The corresponding attribute is swLoadCur-rentFileId and is related only to the swLoad-header file. All charac-ters of the ASCII string are to be in upper case. However, the SW parts in the BTSE handling the file Id are to be case tolerant.
This attribute is a string of 12 alphanumerical characters with the fol-lowing format:
ASCII String for: For download of test SW from local LMT Evo-lution acc.
For download of boot SW from local LMT Evolution acc.
for swLoad-header file
HScnv-vss.SWL
HSTTv-vss.SWL
HSBBv-vss.SWL
for the VAM table file
VScnv-vss.VAM
VSTTv-vss.VAM
VSBBv-vss.VAM
for swImages BTSrrrhh.SWI BTTrrrhh.SWI BTBrrrhh.SWI
for PID files PSBBvvss.PID
hh, cn, vv and ss are identical with the corresponding parts of the FILESWV - please note that thevalues of 'hh' in the FileId of swImages do not reflect the BTSplus mainline family but reflect the HW version of the board. (eg.BTSBIX01.SWI is for the CU and the file BTSBIX07.SWI is for newer CU-variants, eg. the ECU).
The 3 characters used for 'rrr' identify different units:
rrr BS240, BS241, BS240XL,
BS240SR,BS241SR, BS240XLSR,
BS40, BS40II, BS41, BS82, BS82II
BCX for COBA
BIX for CU
LMX for LMU (only BS240, BS241, BS240XL)
12..12 characters string
630DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805ca0eb
f
FILESWVfileVersion
The File Version is a parameter used within the SW download procedures and not of the type 'GET'. The corresponding attribute is swLoadCurrentVersion and is coded identical as File Version. However the allowed values for 'hh' are different because wLoadCur-rentVersion is related only to the swLoad-header file.
Validity Range ASCII string: cn-hh-vv-ii-ss-pp_yy-mm-dd, where:
cn Version part (network operator code)
01 = Ciphering A5.0 + A5.1 + A5.2
02 = Ciphering A5.0 + A5.2 12
03 = Ciphering A5.0 only
hh Version part (HW/SW compatibility code)
vv Version part (feature package code)
02 = BR 2.0
03 = BR 2.1
04 = BR 3.0
07 = BR 3.7
08,09 = BR 4.0
10 = BR 4.5
11 = BR 5.0
12 = BR 5.5
13 = BR 6.0
14 = BR 6.01
15 = BR 6.02
16 = BR 7.0 / 7.01
17 = BR 8.0
18 = BR 9.0
19 = BR 10.0
ii: Version part (sub-feature package code). This field assumes the values: 21 (BTSplus mainline), 26 (BTSplus basic), 25 (BTSplus eMicro)
ss : Version part (actual state)
pp: Patch version (usually 00)
yy-mm-dd: production date (optional)
Notes:
1) For the SWL file of the downloadable test SW of BTSplus mainline, basic and eMicro, the following special value is used:
cn = TT
DN0933412 Issue 01631
BTSplus mainline commands at the Flexi BSC product family
f
Id:0900d805805ca0eb
3) For the SWL file of the downloadable boot SW of BTSplus mainline, basic and eMicro, the following special value is used:
cn = BB
In addition to the ASCII string described above values, the following values are allowed for generic filedownload.
"00" ....Destination ID for Easy-Disk (remaining 24 characters are filled with blanks)
"01" ....Destination ID for Light-Disk Partition 1 (reserved)
"02" ....Destination ID for Light-Disk Partition 2 (reserved)
"03" ....Destination ID for Light-Disk Partition 3 (reserved)
Default ValueNone.
Contained in the following commands:ACTIVATE BTSM, ACTIVATE_DELAYED BTSM
FILETYPEFileType
This attribute specifies the file type to be transferred.
Validity Range
Default ValueNone.
Contained in the following commands:UPLBTSLOG SOFTWARE-MANAGEMENT
FPGAFWVERfpgaFwVer
This attribute gives information on the FPGA FW images that are contained in the board's flash prom together with an indication of the “active” version.
The attribute identifier cannot be present in the listOfRequiredAttributes together with other attribute identifiers and it is not sent by the BTSE obejct if a "Get FCUMAIN"/"Get CU"is done without the information element listOfRequiredAttributes.
Validity Range
ALARM_BUFFER
TRACE_FILE
1 to 4 items of
FPGAfwVer 39..39 characters string
activeFlag active
632DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805ca0eb
f
Default ValueNone.
Contained in the following commands:GET CU, GET CU FWID, GET FCUMAIN, GET FCUMAIN FWID
FRANOFFSframeNumberOffset
This attribute allows to adjust the TDMA frame number offset for a cell. Equal frame and burst number offsets result in synchronized TDMA frames and synchronized TDMA frame numbers.
This attribute is only meaningful enableInterSiteSync is set to 'TRUE'.
Validity Range
Default Value 0
Contained in the following commands:GET BTS
FWVERfirmwareVersion
This attribute provides the firmware version stored on the ETHCON board.
Validity Range
Default ValueNone.
Contained in the following commands:GET ETHCON
stored
0 - 255
0 - 255
<NULL>
DN0933412 Issue 01633
BTSplus mainline commands at the Flexi BSC product family
g
Id:0900d805805b2913
g
GN<x>gain0(dBi*1<x>)
Attribute data provided by the TMA. This attribute shows the gain of the operating band<X> in (dBi * 10).
Validity Range
Default ValueNone.
Contained in the following commands: GET TMA
GNAgainAdjust(dB)
This attribute represents the cable loss measured during installation and entered by the operator at the DIP switch related to a DILNA or DULNA. So the attribute allows the operator to 'GET' the actual DIP switch setting. In 'AMCO_MODE' (attribute lnaMode) the value 0 is returned, in MUCO_MODE (attribute lnaMode) the value 0..7 can be returned. If the value 7 is returned this means that the operator has performed a DIP switch setting at the DIAMCO or DUAMCO/FDUAMCO board which isn't allowed.
Validity RangeIn commands GET DILNA, GET DULNA, GET F6LNA:
0 - 255
<NULL>
N_00
N_01
N_02
N_03
N_04
N_05
N_06
N_07
N_08
N_09
N_10
N_11
N_12
634DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805b2913
g
In commands GET DILNA, GET DULNA:
Default ValueNone.
Contained in the following commands: GET DILNA, GET DULNA, GET F6LNA
GNADBgainAdjustDb
This attribute sets the attenuation value of a MFDUAMCO RX amplifier chain in theda-tabase. The value is aligned with the combiner if a MFDUAMCO is equipped. If the DIP value is set, the MFDUAMCO DIP switch setting is used. The attribute is meaningless if an old DUAMCO or FDUAMCO is equipped. Nevertheless the value is stored in the database and used if a MFDUAMCO is equipped later on
Validity Range
ILLEGAL_VALUE
UNKNOWN
<NULL>
N_00
N_01
N_02
N_03
N_04
N_05
N_06
N_07
N_08
N_09
N_10
N_11
N_12
ILLEGAL_VALUE
UNKNOWN
N_00
N_01
N_02
N_03
N_04
DN0933412 Issue 01635
BTSplus mainline commands at the Flexi BSC product family
g
Id:0900d805805b2913
Default Value
Contained in the following commands: CREATE DULNA, CREATE F6LNA, GET DULNA, GET F6LNA, SET DULNA, SET F6LNA
GNRgainResolution(dB*4)
Attribute data provided by TMA.
Validity Range
Default ValueNone.
Contained in the following commands: GET TMA
GSMTIMEgsmTime
This attribute represents the current frame number of the radio interface. It is counted as a binary presentation 'frame number modulus 42432'.
Validity Range
Default ValueNone.
N_05
N_06
N_07
N_08
N_09
N_10
N_11
N_12
DIP
DIP
0 - 255
<NULL>
0 - 42432
<NULL>
636DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805b2913
g
Contained in the following commands: GET BTS
GTWADRV4gatewayAddressIPv4
This attribute specifies the IPv4 address of the default IP gateway including the subnet-work information. The address is input in the usual IPv4 format. The subnetwork is added in CIDR notation.
Example for CIDR notation:
192.168.2.7/24 corresponds to the host address 192.168.2.7 with subnet mask 255.255.255.0
g Value “0.0.0.0/0” and “0.0.0.0” are intrepreted as attribute not set.
This attribute is visible and configurable only in phase 2 in LMT Evolution local.
Validity Range
Default Value
Contained in the following commands: GET BTSEP NOSWL, SET BTSEP
0..18 characters string
""
DN0933412 Issue 01637
BTSplus mainline commands at the Flexi BSC product family
h
Id:0900d805805b2915
h
HOPMODEhoppingMode
This attribute specifies whether baseband hopping or synthesizer hopping is to be done. This attribute can be changed only when hopping is switched off (Attribute btsIsHop-ping). A prerequisite for synthesizer hopping is that the corresponding HW (TPU + PA) is installed.
Validity Range
Default ValueNone.
Contained in the following commands: GET BTS
HSNhoppingSequenceNumber
This attribute determines the order in which the allocated frequencies are used.
This parameter is used in the frequency hopping algorithm. Any instance of the CHAN object, which is not assigned to any explicit frequency hopping system instance should contain the default value 0 for this attribute.
Changing this attribute is allowed only if there is no hopping (i.e. attribute btsIsHopping = FALSE).
Validity Range
Default Value 0
Contained in the following commands: GET CHAN
BBHOP
SYNHOP
0 - 63
638DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805b2917
i
i
INSDinstallDate
Attribute data provided by TMA.
Validity Range
Default ValueNone.
Contained in the following commands: GET TMA
INSIDinstallerId
Attribute data provided by TMA.
Validity Range
Default ValueNone.
Contained in the following commands: GET TMA
INTAVEPARintaveParameter
This attribute contains the measurement and averaging period for the interference clas-sification of idle traffic channels in units of SACCH multiframes.
Validity Range
Default Value 31
Contained in the following commands: GET BTS
0..6 characters string
0..5 characters string
1 - 31
DN0933412 Issue 01639
BTSplus mainline commands at the Flexi BSC product family
i
Id:0900d805805b2917
INTCLASSenableInterferenceClass
This attribute indicated whether the interference classification of idle traffic channels is enabled or disabled.
A change of the attribute becomes effective in the next SACCH multiframe.
A consequence of the value 'disabled' is that no 'RF resource indication' messages are sent to the Flexi BSC product family.
(TRUE = enabled)
Validity Range
Default Value TRUE (enabled)
Contained in the following commands: GET BTS
INTINFinterfaceInformation
This attribute is used to configure one of the envaBTSE instances with the following information:
positive logic with external detector
or
negative logic with external detector
Validity Range
Default ValueNone.
Contained in the following commands: CREATE ENVABTSE, GET ENVABTSE, SET ENVABTSE
INTLVBNDinterferenceLevelBoundaries
This attribute defines the boundary limits of five interference bands for the unallocated timeslots.
The Flexi BSC product family maps the averaged interference level measurements into these five bands.
FALSE
TRUE
low
high
640DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805b2917
i
A change of the attribute becomes effective in the next SACCH multiframe.
The validity range of the attribute is 0 ... 63 (less than -110 dBm...more than -48 dBm) in steps of 1 dBm.
Validity Range
Default Value intThrBou1 : 2
intThsBou2 : 6
intThsBou3 : 12
intThsBou4 : 22
intThsBou5 : 63
Contained in the following commands: GET BTS
IPADRipAddress
This attribute specifies the IP address of the host which shall respond to the ping request. The address is input in the usual IPv4.
The length may vary from minimum length (7 ) -> 1.3.6.9 up to maximum length (15) -> 192.120. 110.124
Validity Range
Default ValueNone.
Contained in the following commands: PING BTSEP
intThrBou1 0 - 63
intThsBou2 0 - 63
intThsBou3 0 - 63
intThsBou4 0 - 63
intThsBou5 0 - 63
7..15 characters string
DN0933412 Issue 01641
BTSplus mainline commands at the Flexi BSC product family
l
Id:0900d805805b2919
l
L1CTRLTSlayer1ControlTs
This attribute defines in case of a LOOP configuration which dedicated layer 1 16kbit/s subchannel is to be used for the layer 1 supervision. In a star or multidrop configuration the given time slot is used for a loopback supervision.
Below are indicated some more detailed information about the attribute validity range:
• TimeSlotNumber for Time Slot in 2 Mb/s link:validity range: 1..31 (if dedicated 16k subchannel is used fo supervision
• TimeSlotNumber for Time Slot in 1,5 Mb/s link:validity range: 1..21 (if dedicated 16k subchannel is used fo supervision
• SubSlotNumber for SubSlot within time slotvalidity range: 0..3 (if dedicated 16k subchannel is used fo supervision
Validity Range
Default Value TimeSlotNumber:
0 (deactivated)
SubSlotNumber:
octet #2 = 3
octet #4 = 0
Contained in the following commands: CREATE BPORT, GET BPORT, SET BPORT
L1PTlayer1ProtocolType
"This attribute defines the type of protocol that is used on layer 1 of the Abis-line. One of the following values has to be set by the operator at installation time for a PCM30 line:
The value 'pcm30crc4' means that a cyclic redundancy check (CRC4) is performed, the value 'pcm30noncrc4doubleframe' means that CRC4 is not performed and that the line remains in Doubleframe mode.
The value 'pcm24sf' means the 'superframe' format is used.
The value 'pcm24crc6esf' means the 'extended superframe' format is used and a cyclic redundancy check (CRC6) is performed.
TSL 0 - 31
SSL 0 - 3
642DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805b2919
l
Validity Range
Default ValueNone.
Contained in the following commands: CREATE BPORT, GET BPORT
L1RATlayer1RemoteAlarmType
This attribute defines how the signalling of a remote alarm is done for both detection and transmission. It must be set accordingly in the remote environment. 'Special Bit Robbing' is allowed only for PCM24 and means that a special bit (bit 2) is used for signalling a remote alarm.
Validity Range
Default Value ProtocolSignalling
Contained in the following commands: CREATE BPORT, GET BPORT, SET BPORT
LAPDCHlapdChannel
This attribute exists for only for LAPDLE. It identifies the BPortNumber, Timeslot Number and Subslot Number allocated on the Abis-interface for the LAPD signaling links to the Flexi BSC product family.
Notes:
The BPortNumber (BPORT) field assumes the following values:
• 00-07 for hh-ii = 04-21 (enums: BPORT0, BPORT1, ..., BPORT7) *) • 00 for hh-ii = 04-25 (enum: BPORT0) • 00-03 for hh-ii = 04-26 (enum: BPORT0, …, BPORT3)
*) for BS82II only BPortNumber 00-03 value is allowed.
- the TSL field has the following ranges:
pcm30crc4
pcm30noncrc4doubleframe
pcm24sf
pcm24crc6esf
ProtocolSignalling
SpecialBitRobbing
DN0933412 Issue 01643
BTSplus mainline commands at the Flexi BSC product family
l
Id:0900d805805b2919
• 01-1F for PCM30 • 01-18 for PCM24
- the SSL field has the following bit associations:
• 0for bit 7 and 6 on LMT Evolution displayed "SSL0_16KB" • 1for bit 5 and 4 on LMT Evolution displayed "SSL1_16KB" • 2for bit 3 and 2 on LMT Evolution displayed "SSL2_16KB" • 3for bit 1 and 0 on LMT Evolution displayed "SSL3_16KB" • 0x10 for bit 7, 6, 5 and 4 on LMT Evolution displayed "SSL0_32KB" • 0x11for bit 3, 2, 1 and 0 on LMT Evolution displayed "SSL1_32KB" • 0xFF 64 kbit/sec on LMT Evolution displayed "FULL_64KB"
Validity Range
Default ValueNone.
Contained in the following commands: CREATE LAPDLE, GET LAPDLE
LAPDOVLTlapdOverloadTimer(sec)
The attribute defines the time between two subsequent 'LAPD overload' messages (in seconds), as long as any radio signalling LAPD link on Abis is overloaded.
The validity range is indicated in seconds.
Validity Range
BPORT BPORT0
BPORT1
...
BPORT7
TSL 1 - 18
SSL SSL0_16KB
SSL1_16KB
SSL2_16KB
SSL3_16KB
SSL0_32KB
SSL1_32KB
FULL_64KB
lapdOverloadTimer 1 - 60
644DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805b2919
l
Default ValuelapdOverloadTimer: 1 second
lapdUsageOverloadTimer: 1 second
Contained in the following commands: GET BTSM OVERLOAD
LAPDOVLTHlapdOverloadThresholds(%)
Validity Range
lapdUsageOver-loadTimer
0.5 - 10.0
The thresholds give the percentage of the LAPD transmit queue filling, allowed range is 10 to 100 (decimal):
a) first level upper threshold : when exceeded sending of mea-surement report messages on Abis will be suspended.
b) second level upper threshold : when exceeded on any of the LAPD links the periodical sending 'LAPD overload' message is started.
c) first level lower threshold: when filling level falls below, sending of measurement reports on Abis will resume.
d) second level lower threshold : when filling level falls below, sending of 'LAPD overload' indication will be stopped.
For thresholds the following restriction is valid:
- first level lower threshold < first level upper threshold =< second level lower threshold < second level upper threshold
Default Value:
50 first level upper threshold
40 first level lower threshold
90 second level upper threshold
80 second level lower threshold
firstLevUp-perThreshold
10 - 100
firstLevLow-erThreshold
10 - 100
firstLevReduction-Step
10 - 100
secLevUp-perThreshold
10 - 100
DN0933412 Issue 01645
BTSplus mainline commands at the Flexi BSC product family
l
Id:0900d805805b2919
Default ValueNone.
Contained in the following commands: GET BTSM OVERLOAD
LCONFlineConfiguration
Validity Range
Default ValueNone.
Contained in the following commands: CREATE BPORT, GET BPORT, SET BPORT
LIMPlineImpedance
secLevLow-erThreshold
10 - 100
This attribute defines the configuration of the BTSplus mainlines on the Abis interface.
Notes:
a) 'star' means either a BTSE which is directly connected to the Flexi BSC product family or the last BTSplus mainline of a multidrop chain.
b) In general 'star' is allowed only for even BPORT instances. Only for hh-ii = 04-01 'star' may be used also for odd BPORT instances (2k+1, k=0, 1, 2, 3) - in this case the related even BPORT instance (2k, k=0, 1, 2, 3) must be configured as 'star' too.
c) more information can be found in the document 'Configuration Rules for BTSE Abis Line Interface'.
star
multidrop
loop
starX
This attribute defines the impedance setting of the related Abis (BPort) interface.
Notes:
646DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805b2919
l
Validity Range
Default Value accDIP (fully correct for COBA2P8 internal used by subsystem DM)
Contained in the following commands: CREATE BPORT, GET BPORT, SET BPORT
LMTLSESSlmtLogonSession
This attribute indicates if a LMT Evolution session is active or not.
Validity Range
a) On a COBA2P8 the adjustment of the impedance is done by DIP switches. So the only acceptedvalue on a COBA2P8 is 'AccDIP'.
b) On a COBA4P12 the adjustment is performed by software. So the value must be 'Imp100or120Ohm' or 'Imp75Ohm'.
c) If a value which is not allowed is entered the BTSE SW will answer with a NACK.
d) The initial value 02 will be changed by BTSE subsystem A1 to 00 in case of COBA4P12."
e) In case of backup from COBA2P8 to COBA4P12 it is handled "fault tolerantly", SET message will be acknowledged and alarm will be issued. A1 sub-system will change value of the attribute to appropriate default value 00 automatically.
Imp100or120Ohm
Imp75Ohm
accDIP
NOT_ACTIVE
ACTIVE
DN0933412 Issue 01647
BTSplus mainline commands at the Flexi BSC product family
l
Id:0900d805805b2919
Default Value NOT_ACTIVE
Contained in the following commands: GET BTSEP NOSWL
LMTLTIMElmtLogonTime
This attribute specifies the date and time of the logon attempt. It is set by the BTSE when the T- interface message 'Logon' from the local LMT Evolution is received.
Validity Range
Default Value year : 1995
month : 8
day : 1
hour : 0
minute : 0
second : 0
Contained in the following commands: GET BTSEP NOSWL
LMTUALlmtUserAccessLevel
This attribute indicates the LMT Evolution user profile.
Validity Range
year 1990 - 2037
month 1 - 12
day 1 - 31
hour 0 - 23
minute 0 - 59
second 0 - 59
offsetHour -12 - 14
offsetMinute 0 - 45
READ_ONLY
COMMAND
READ_WRITE
648DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805b2919
l
Default Value NOT_DEFINED
Contained in the following commands: GET BTSEP NOSWL
LMTUNAMElmtUserName
Validity Range
Default Value octet 3-10 = 0, octet 2 = 7
Contained in the following commands: GET BTSEP NOSWL
LNAMDBlnaModeDb
new information
Validity Range
Default Value
ACCESS_CONTROL_MANAGEMENT
SECURITY_OPERATOR
NOT_DEFINED
The user name consists of a character string containing maximal 7 characters for the user name. The user name must be terminated by a NUL character value (last byte of the user name). The content of this attribute is identical with the content of the information element 'user identification' of the T-interface message 'Logon'.
Default Value: octet 3-10 = 00, octet 2 = 07
1..14 characters string
MUCO_MODE
AMCO_MODE
DIP
DIP
DN0933412 Issue 01649
BTSplus mainline commands at the Flexi BSC product family
l
Id:0900d805805b2919
Contained in the following commands: CREATE DULNA, CREATE F6LNA, GET DULNA, GET F6LNA, SET DULNA, SET F6LNA
LNAMODElnaMode
This attribute indicates the current amplification mode of a DUAMCO_LNA or DIAMCO_LNA. (The information is derived from the setting of the DIP switch 'mode switch' and from the actual situation e.g. regarding the TMA) This attribute is 'readonly'.
Validity Range
Default Value UNKNOWN
Contained in the following commands: GET DILNA, GET DULNA, GET F6LNA
LNAPREDlnaPredecessor
This attribute is optional and indicates the wiring of the RX input of a DUAMCO_LNA/ DIAMCO_LNA to the RX cascade output (RXCA) of another DUAMCO_LNA/DIAMCO_LNA or to the RX output of a TMA.
From SW point of view the FDUAMCO is considered just as an HW variant of the DUAMCO, so an extra term like 'FDUAMCO_LNA' is not introduced.
If there is no wiring the operator must not provide a value for the attribute.
If there is no wiring and the operator enters a value for the attribute he can correct the error only by a deletion of the object and a re-creation of the object.
Detailed information about the validity range:
predecessor (Type):
DULNA (not allowed for BS82II)
DILNA (not allowed for BS82II)
TMA
predecessor (Rack):
RACK0
RACK1
RACK2
MUCO_MODE
AMCO_MODE
UNKNOWN
650DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805b2919
l
If predecessor(type) is TMA the predecessor(rack) must be the same as the rack of the DILNA/DULNA, i.e. the TMA connected to a DILNA/DULNA must be created in the same rack as the DILNA/DULNA object.
predecessor (relative number):
DULNA 0 ... 7
DILNA 0 ... 7 (for BS240XL only 4 ... 7)
TMA 0 ... 15 (for BS240XL only 12 ... 15)
Validity RangeIn commands CREATE DILNA, CREATE DULNA, CREATE F6LNA:
predType DILNA predRack RACK0
RACK1
RACK2
predNo DILNA0
DILNA1
...
DILNA7
DULNA predRack RACK0
RACK1
RACK2
predNo DULNA0
DULNA1
...
DULNA7
TMA predRack RACK0
RACK1
RACK2
predNo TMA0
TMA1
...
TMA15
F6LNA predRack RACK0
RACK1
RACK2
predNo F6LNA0
F6LNA1
...
F6LNA3
DN0933412 Issue 01651
BTSplus mainline commands at the Flexi BSC product family
l
Id:0900d805805b2919
In commands GET DILNA, GET DULNA, GET F6LNA:
Default ValueNone.
Contained in the following commands: CREATE DILNA, CREATE DULNA, CREATE F6LNA, GET DILNA, GET DULNA, GET F6LNA
predType DILNA predRack RACK0
RACK1
RACK2
predNo DILNA0
DILNA1
...
DILNA7
DULNA predRack RACK0
RACK1
RACK2
predNo DULNA0
DULNA1
...
DULNA7
TMA predRack RACK0
RACK1
RACK2
predNo TMA0
TMA1
...
TMA15
F6LNA predRack RACK0
RACK1
RACK2
predNo F6LNA0
F6LNA1
...
F6LNA3
<NULL>
652DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805b2919
l
LOCALADDRlocalAddress
Local IP address of the Circuit Emulation Service Tunnel. The address is input in the usual IPv4 format. For addressing examples please see also attribute ipAddress. The object must be locked before modifying the address via the SET command.
Validity Range
Default ValueNone.
Contained in the following commands: CREATE CESTUNNEL, GET CESTUNNEL, SET CESTUNNEL
LOCLUDPlocalUdpPort
Local UDP port number of the CESPW instance. It is recommended to use identical port numbers for the local and the peer UDP port. The object must be locked before modi-fying the port number via the SET command.
Validity Range
Default ValueNone.
Contained in the following commands: CREATE CESPW, GET CESPW, SET CESPW
LOCNAMElocationName
Validity Range
Default ValueNone.
Contained in the following commands: GET BTSEP NOSWL, SET BTSEP
7..15 characters string
49152 - 65535
This attribute is a ASCII string (max 37 characters) which identifies a location.
Default Value: EARTH
1..37 characters string
DN0933412 Issue 01653
BTSplus mainline commands at the Flexi BSC product family
l
Id:0900d805805b2919
LOSPKTTHlostPacketThreshold
new information
Validity Range
Default Value
Contained in the following commands: CREATE CESTUNNEL, GET CESTUNNEL, SET CESTUNNEL
LPDLMSATlapdleLinkSatellited
The attribute informs the BTSplus mainline SW about the settings in the Flexi BSC product family regarding the presence of a satellite on the Abis interface. The attribute is sent only during the 'BTSE Alignment Procedure'. The BTSE SW stores the value only as information for the operator. However when the attribute is stored the BTSE SW performs a semantic check which compares the value of lapdmLinkSatellited with the value of the attribute sAbisLinkSatellited (ABISLKSAT). The BTSE SW reports a minor alarm if both values do not match. The BTSE object is set to enabled.degraded as long as the alarm is active. In order to clear the alarm the operator has to take steps that LPDLMSAT and ABISLKSAT have a consistent value - a consequence of this action is an interruption of the Abis link (as a change of ABISLKSAT is only possible at the BTSE-LMT Evolution in phase 2 and a change of LPDLMSAT requires a deletion and re-creation of the BTSM object at the LMT Evolution or at the NetAct).
Validity Range
Default Value terrestrialConnection
Contained in the following commands: GET BTSM NOSWL
LRUlru
This attribute describes an object class and instance of a specific board that is affected by the firmware upgrade.
1 - 100
1
terrestrialConnection
satelliteConnection
654DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805b2919
l
Validity Range
Default ValueNone.
Contained in the following commands: FWUPGRADE BTSM
LSINDlineStatusIndication
siemensHw HwP
HwXS
typeOfHw Cu
Coba
Fcumain
Duamco
Ficom6
rackNbr 0 - 2
boardNbr 0 - 11
This attribute identifies the PCM link status values, that additionally will be displayed via LED(s) at the LI or COBA/COSA. More than one status might be valid at a time.
Bit 0: RemoteAlarmIndication
01 TRUE
00 FALSE always FALSE in case of ISDN S0
Bit 1: FrameSynchronizationLoss
01 TRUE
00 FALSE
Bit 2: CRCFailure
01 TRUE
00 FALSE always FALSE in case of ISDN S0
Bit 3: NoLevel (Line is broken)
01 TRUE
00 FALSE
Bit 4: CRCFailureRemoteEnvironment
01 TRUE
00 FALSE always FALSE in case of ISDN S0
Bit 5: BitErrorRate > lowerThreshold of 'bitErrorRateThresholds'
DN0933412 Issue 01655
BTSplus mainline commands at the Flexi BSC product family
l
Id:0900d805805b2919
Validity Range
Default ValueNone.
Contained in the following commands: GET BPORT
01 TRUE
00 FALSE always FALSE in case of ISDN S0
Bit 6: BitErrorRate > upperThreshold of 'bitErrorRateThresholds'
01 TRUE
00 FALSE always FALSE in case of ISDN S0
Bit 7: PromptMaintenanceAlarmIndication
01 TRUE
00 FALSE
RemoteAlarmInd FALSE
TRUE
FrameSynchroniza-tionLoss
FALSE
TRUE
CRCFailure FALSE
TRUE
NoLevel FALSE
TRUE
CRCRemoteEnviro-ment
FALSE
TRUE
BERTLowerThresh-old
FALSE
TRUE
BERTUpperThresh-old
FALSE
TRUE
PromptMainte-nanceAlarmInd
FALSE
TRUE
<NULL>
656DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805b291b
m
m
MACADDRmacAddress
This attribute provides the MAC address of the Ethernet port instance. Attribute is coded as a string with 17 characters with hexadecimal representation of the MAC address (e.g. 09:03:20:ae:ec:7b).
Validity Range
Default ValueNone.
Contained in the following commands: GET COBAETHINTF
MAIOmaio
"Hopping physical channels on the same timeslot with the same mobile allocation (con-tained in the aRFCNList) must use the same value of hoppingSequenceNumber and dif-ferent values for MAIO (Mobile Allocation Index Offset). This prevents frequency collision.
The maximum value of mAIO depends on the number of frequencies in the attached ARFCNList. For a set of N allocated frequencies in the ARFCNList there must be N dif-ferent values for mAIO (0...N-1).
Any instance of the object CHAN which is not assigned to any explicit frequency hopping system instance should contain the default value 0 for this attribute."
Changing this attribute is allowed only if there is no hopping (i.e. attribute btsIsHopping = FALSE).
Validity Range
Default Value 0
Contained in the following commands: GET CHAN
MAXGNmaxGain(dB*4)
Attribute data provided by TMA.
17..17 characters string
0 - 63
DN0933412 Issue 01657
BTSplus mainline commands at the Flexi BSC product family
m
Id:0900d805805b291b
Validity Range
Default ValueNone.
Contained in the following commands: GET TMA
MAXPDVmaxPdv(ms)
The attribute defines the maximum packet delay variation value. It is used for dimension-ing of the jitter buffer. The object must be locked before modifying the maxPdv value via SET command.
Validity Range
Default Value
Contained in the following commands: CREATE CESPW, GET CESPW, SET CESPW
MINGNminGain(dB*4)
Attribute data provided by TMA.
Validity Range
Default ValueNone.
Contained in the following commands: GET TMA
MOBALLOCarfcnList
0 - 255
<NULL>
0.125 - 30.000
2.000
0 - 255
<NULL>
mobileAllocation / trxFrequency
658DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805b291b
m
This attribute is contained in the functional objects transceiver and channel.
Octet 2 tells the number of frequencies in the list. The remaining number of octets of this information element (aRFCNList) is twice the value of this field.
If the attribute is contained in a message related to the transceiver the value of "Number of ARFCNs in List" must be 1, i.e. only one ARFCN is allowed. (The name at the GUI is 'trxFrequency" in this case.
If the attribute is contained in a message related to the channel (The name at the GUI is 'mobileAllocation" in this case.) the value of "Number of ARFCNs in List" is : <00-40>, <0- 64> (decimal)
The value 0 has the special meaning that the corresponding channel instance is not assigned to any frequency hopping system instance and that the BTSE has to use the ARFCN value of the TRX which contains the channel.
ARFCN1..ARFCNn shall be contained in ascending order with no duplicates.
cellAllocationNum-ber
Hex Decimal
GSM900 "BB900" 0001 ... 007C 1 ... 124
GSM EXTENDED "F2ONLY900"
0000 ... 007C
03CF ... 03FF
0 ... 124
975 ... 1023
GSM EXTENDED REDUCED "EXT900"
0000
0000 ... 007C
03CF ... 03FF
0
0 ... 124
975 ... 1023
DCS 1800 "DCS1800"
0200 ... 0375 512 ... 885
PCS 1900 0200 ... 032A 512 ... 810
GSM-R 03BB ... 03CE 955 ... 974
GSM-DCS 0000 ... 007C
03CF ... 03FF
0200 ... 0375
0 ... 124
975 ... 1023
512 ... 885
GSM850 0080 ... 00FB 128 ... 251
GSM850-PCS 0080 ... 00FB
0200 ... 032A
128 ... 251
512 ... 810
GSM850-DCS 0080 ... 00FB
0200 ... 0375
128 ... 251
512 ... 885
DN0933412 Issue 01659
BTSplus mainline commands at the Flexi BSC product family
m
Id:0900d805805b291b
Validity Range
Default Value octet #2 = 0 (only for aRFCNList related to "CHAN")
Contained in the following commands: GET CHAN
MOECmemberOfEmergencyConfig
The attribute memberOfEmergencyConfiguration specifies whether a TRX should still operate for a given time (emergencyTimer1) if a "battery backup operation" (due to "mains breakdown") occurs. If an emergency because of overtemperature occurs, this attribute specifies a TRX which is not powered off immediately.
If this feature is wanted the value TRUE should be used at least for the BCCH TRX. If FALSE is used for the BCCH TRX and TRUE is used for another TRX in the cell a BCCH reconfiguration would be triggered if a "battery backup operation" (due to "mains break-down") or overtemperature occurs.
g The switch to emergency configuration or zero configuration in case of overtemper-ature only depends on the temperature itself (two different values for emergency and zero configuration) and does not depend on the emergencyTimer1/2.
Validity Range
Default Value TRUE
Contained in the following commands: GET TRX
MONPRTmonitoringPort
This attribute defines the port which is used for Abis traffic monitoring on the ETHCON module.
Changing or setting this attribute for a TRX means a temporary loss of service for the TRX.
Changing this attribute for a CHAN is allowed only if there is no fre-quency hopping (i.e. attribute btsIsHopping = FALSE).
0 to 64 items of
0 - 1023
TRUE
FALSE
660DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805b291b
m
The attribute enables mirroring of packets for the configured monitoringPort. The port number corresponds to the ETHPORT instance number. Port mirroring can be enabled for maximum one port.
The system does not check if the referenced port is already created.
Validity Range
Default Value
Contained in the following commands: GET ETHCON, SET ETHCON
MORTMOT
This Attribute describes an object instance. The MOT attribute defines the HW-MO that will have its internal resources tested.
Below are reported some detailed information about the validity range.
for: BS240, BS40 BS240SR BS40II BS82II
BS241, BS41 BS241SR
BS240XL BS240XLSR
ACDCP - Y Y - Y
ACT Y Y Y Y Y
BATTERY - Y Y - Y
COBA #) Y Y - Y Y
COSA Y Y - Y -
CU Y Y - Y Y
DIDCTMA Y Y - - Y
DILNA Y Y - - Y
DUDCTMA Y Y - Y Y
DULNA Y Y - Y Y
DUVSWR Y Y - Y Y
none
port0
port1
port2
port3
coba
none
DN0933412 Issue 01661
BTSplus mainline commands at the Flexi BSC product family
m
Id:0900d805805b291b
FANP *) Y Y Y Y Y
FCUMAIN Y Y - Y Y
FCUTR Y Y - Y Y
FTNFP Y Y - Y -
FVSWRP Y Y - Y -
LMU Y - - - -
TMA *) Y Y - Y Y
*) no processor #) COBA #0 only possible via LMT Evolution on
phase 2
Validity Range
Default ValueNone.
Contained in the following commands: GET BTSETEST, PERFTEST BTSEP, STOPTEST BTSEP
MPHERRmaxPhaseError(microsec)
This attribute specifies the desired maximum phase deviation of the base clock on the COBA in respect to the GPS clock. If the current phase deviation exceeds this desired maximum value an alarm is issued and the attribute clockAccuracy is set to the reduced accuracy level 'high'. This attribute is only meaningful if the attribute syncSource is set to 'extGPS' and the attribute enableInterSiteSync is set to 'TRUE'.
Validity Range
Default Value
Contained in the following commands: GET SYNCBTSE, SET SYNCBTSE
MPTSLXXmappingTSLXX
This attribute describes to which "time slot" of the specified Bport the TS xx of the Bport related to the given XConnect instance is to be mapped; e. g. 'mappingTSL02' of XConnect 0 describes the mapping of time slot 2 of BPort 0 (which corresponds to XConnect 0) to a time slot (targetTSL) of a BPort instance (targetBPort). If the 'target BPort' value is equal to the value of the XConnect instance this means that a "remap-ping" between the time slot position on the Abis line and the BTSplus mainline internal
Pathname
1.5 - 15.0
1.5
662DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805b291b
m
position is done- this is allowed only in LMT Evolution phase 2. The purpose for this "remapping" usually is to have the traffic data and signalling data in the BTSplus mainline at the same positions as at the PCM lines directly connected to the Flexi BSC product family (and as indicated in the attributes abisChannel and lapdChannel)- this is needed e.g. if there is a sequence of several PCM lines between Flexi BSC product family and the BTSplus mainline involving multidrop/loop and cross connect configura-tions.
In case of PCM24 only mappingTSL01..mappingTSL24 are meaningful.
XConnect instance 0 is related to BPORT instance 0
XConnect instance 1 is related to BPORT instance 1
XConnect instance 2 is related to BPORT instance 2
XConnect instance 3 is related to BPORT instance 3
XConnect instance 4 is related to BPORT instance 4
XConnect instance 5 is related to BPORT instance 5
XConnect instance 6 is related to BPORT instance 6
XConnect instance 7 is related to BPORT instance 7
note on targetTSL validity range:
- targetTSL : 0 ... 24 for time slot in 1,5 Mb/s link
- targetTSL : 0 ... 31 for time slot in 2 Mb/s link
targetBport = 0 and targetTSL = 0 mean 'no mapping'
Validity Range
Default Value
Contained in the following commands: CREATE XCONNECT, GET XCONNECT, SET XCONNECT
MRSYNCTmaxResyncTime(min)
This attribute allows the operator to adjust the maximum re-synchronization time to reach the desired phase accuracy defined with the attribute maxPhaseError. If the esti-mated re-synchronization time exceeds this value an alarm is issued, which informs the operator that a manual re-synchronization should be considered. The time can be adjusted between 0 and 24 hours (i.e. 0-1440 minutes). This attribute is only meaningful if the attribute syncSource is set to 'extGPS' and the attribute enableInterSiteSync is set to 'TRUE'.
targetBport 0 - 7
targetTSL 0 - 31
targetBport 0
targetTSL 0
DN0933412 Issue 01663
BTSplus mainline commands at the Flexi BSC product family
m
Id:0900d805805b291b
Validity Range
Default Value
Contained in the following commands: GET SYNCBTSE, SET SYNCBTSE
MSDISTBEHAVmsDistanceBehaviour
This attribute defines the executions allowed after the Timing Advance parameter has exceeded the threshold.
Validity Range
Default ValueNone.
Contained in the following commands: GET BTS
MSTXPMAXmSTxPwrMax(*dBm mapped)
This attribute indicates the maximum power level an MS may use in the serving cell. In case of GSMDCS, GSM850-PCS and GSM850-DCS mixed cells the attribute repre-sents the maximum power level a MS may use in the band to which the BCCH belongs.
Below are listed some detailed validity range values
GSM / GSM-R:
39 dBm
37 dBm
:
33 dBm, Default Value
:
15 dBm
13 dBm
DCS 1800:
30 dBm, Default Value
28 dBm
:
02 dBm
0 - 1440
180
0 - 255
664DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805b291b
m
00 dBm
PCS 1900:
30 dBm, Default Value
28 dBm
:
02 dBm
00 dBm
33 dBm
32 dBm
Validity Range
Default ValueNone.
Contained in the following commands: GET BTS
MSTXPMAXCmSTxPwrMaxCompl
This attribute is meaningful only in case of GSM-DCS, GSM850-PCS and GSM850-DCS mixed cells and represents the maximum power level a MS can use in the band of the serving cell to which the BCCH doesn't belong. A change of the attribute becomes effective with the next call.
BCCH is in the DCS or PCS band - the MS can use the specified value
for the maximum power in the GSM band (i.e. in the band complementary
to the BCCH band)
39 dBm
37 dBm
:
33 dBm, Default Value
:
15 dBm
13 dBm
BCCH is in the GSM band - the MS can use the specified value for the
maximum power in the DCS band (i.e. in the band complementary to
the BCCH band)
30 dBm, Default Value
0 - 31
DN0933412 Issue 01665
BTSplus mainline commands at the Flexi BSC product family
m
Id:0900d805805b291b
28 dBm
:
02 dBm
00 dBm
BCCH is in the GSM band - the MS can use the specified value for the
maximum power in the PCS band (i.e. in the band complementary to
the BCCH band)
30 dBm, Default Value
28 dBm
:
02 dBm
00 dBm
33 dBm
32 dBm
Validity Range
Default ValueNone.
Contained in the following commands: GET BTS
MTLTmechanicalTilt(degree*10)
Attribute data provided by TMA.
Validity Range
Default ValueNone.
Contained in the following commands: GET TMA
MTYPmediaType
This attribute indicates the type of the physical medium used for the given instance of Ethernet port.
0 - 31
0 - 65535
<NULL>
666DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805b291b
m
Validity Range
Default ValueNone.
Contained in the following commands: GET ETHPORT
electrical
optical
<NULL>
DN0933412 Issue 01667
BTSplus mainline commands at the Flexi BSC product family
n
Id:0900d805805b291d
n
NEPTTREPnotDataRepCount
The attribute allows to choose between different PDV compensation parameter sets which are optimized to certain network behaviors.
Validity Range
Default ValueNone.
Contained in the following commands: GET BTS
NTWTYPCnetworkTypeCompensation
This attribute defines the type of network (in terms of frequency band(s)) the BTSplus mainline is working in. Further more it indicates the type of a possible complementary frequency band when handling Dual Band MSs.
Validity Range
Default Value
Contained in the following commands: CREATE CESTUNNEL, GET CESTUNNEL, SET CESTUNNEL
NTWTYPEnetworkType
This attribute defines the type of network (in terms of frequency band(s)) the BTSplus mainline is working in. Further more it indicates the type of a possible complementary frequency band when handling Dual Band MSs.
Below are listed some details about the attribute validity range:
GSMDCS:
GSM 900
DCS 900
GSM EXTENDED
0 - 3
0 - 255
0
668DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805b291d
n
GMS EXTENDED REDUCED
GMS-DCS
GSMPCS:
GSM 900
GSM EXTENDED
GMS EXTENDED REDUCED
PCS 1900
GSMR:
GSM-R
.
.
GSM850PCS:
PCS 1900
GSM850
GSM850PCS
GSM850DCS:
DCS 1800
GSM850
GSM850DCS
GSMRAIL PUB:
GSM 900
DCS 1800
GSM EXTENDED
GMS EXTENDED REDUCED
GSM-R
GSM-DCS
Validity Range
GSMDCS
GSMPCS
GSMR
GSM850PCS
GSM850DCS
DN0933412 Issue 01669
BTSplus mainline commands at the Flexi BSC product family
n
Id:0900d805805b291d
Default ValueNone.
Contained in the following commands: GET BTS
NY1ny1
This attribute indicates the maximum number of repetitions of the PHYSICAL INFOR-MATION message on the radio interface. This message is sent by the BTSplus mainline to the MS during a handover procedure between two not synchronised cells, in order to establish a physical channel connection on the new cell. If the maximum number of rep-etitions is reached, the newly allocated channels are released and the context related to the handover is abandoned. ny1 is a binary presentation of maximum number of repeti-tions of PHYSICAL INFORMATION.
Note: (ny1) * (BTS Air Timer t3105) must be greater than the maximum Um Layer 2 response time.
Validity Range
Default Value 30
Contained in the following commands: GET BTS
NY2ny2
As a result of an Uplink Access of a mobile station the network grants the uplink to the mobile station by sending a VGCS UPLINK GRANT message periodically. ny2 is the counter value which defines the number of repetitions of sending the message.
Validity Range
Default Value 20
Contained in the following commands: GET BTS
1 - 254
1 - 254
670DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805b2e35
o
o
OMLAPDRTomLapdRelTimer(sec)
At the detection time of the Abis link failure (which may happen at different times in the BTSplus mainline and in the Flexi BSC product family), the BTSplus mainline starts the timer omLAPDRelTimer and the Flexi BSC product family starts the timer shortLAPDInt-Timer. If the timer omLAPDRelTimer expires, the BTSplus mainline blocks the call pro-cessing. After that the BTSplus mainline forces the Flexi BSC product family (via a RestartSendingEventReports-NACK message) to perform a complete Abis alignment. If none of the two timers expires, the Flexi BSC product family performs a 'Short Abis alignment'. The default value of omLAPDRelTimer should be kept greater than the default value of the attribute shortLAPDIntTimer.
The validity range step size is 1 second.
Validity Range
Default Value 30 seconds
Contained in the following commands: GET BTSM NOSWL
OSToperationalState
This attribute defines whether or not the resource is physically installed and working.
Validity Range
Default Value DISABLED for Functional Objects
Contained in the following commands: GET ACDCP, GET ACT, GET BATTERY, GET BCOM, GET BPORT, GET BTS, GET BTSEP NOSWL, GET BTSM NOSWL, GET CESPW, GET CESTUNNEL, GET CHAN, GET COBA, GET COBAETHINTF, GET COSA, GET CU, GET DIDCTMA, GET DILNA, GET DUAMCO, GET DUDCTMA, GET DULNA, GET DUVSWR, GET ENVABTSE, GET ETHCON, GET ETHPORT, GET F6DCTMA, GET F6LNA, GET F6TNFP, GET F6VSWRP, GET FANP, GET FCUMAIN, GET FCUTR, GET FTNFP, GET FVSWRP, GET LAPDLE, GET RACK, GET SYNCBTSE, GET TMA, GET TRX, GET XCONNECT
3 - 300
DISABLED
ENABLED
DN0933412 Issue 01671
BTSplus mainline commands at the Flexi BSC product family
o
Id:0900d805805b2e35
OUTPUToutput
New Information.
Validity Range
Default ValueNone.
Contained in the following commands:None.
OUTPUTPRoutputPowerReduction
The attribute specifies if and how the maximum output power of the carrier unit / FlexCU carrier has to be reduced because of the setting of the BTS attribute 'carrierUnitConfig-uration.
This attribute is valid only for CU and FlexCU.
Validity Range
Default ValueNone.
Contained in the following commands: GET CU, GET FCUTR
OVERWRITEOverwrite
0..80 characters string
db0
db1
...
db4
This attribute specifies whether the existing BTS-SW on the Flexi BSC product family hard disk will be overwritten (YES) or not (NO) (UPLBTSLOG).
This attribute specifies whether the existing file containing the Alarm Buffer SW will be overwritten (YES) or not (NO) (UPLBTSLOG).
This attribute specifies whether the existing IDT file will be overwritten (YES) or not (NO) (UPLLIDF).
672DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805b2e35
o
Validity Range
Default ValueNone.
Contained in the following commands: DNLALLEXE SOFTWARE-MANAGEMENT, UPLBTSLOG SOFTWARE-MANAGE-MENT, UPLLIDF REMINV
OVPTINSovptInstalled
This attribute indicates whether an OVPT board is installed or not. It can be set only in LMT Evolution phase 2. The attribute is used to adapt the pulse mask according to the recommendations.
Validity Range
Default Value
Contained in the following commands: GET BTSEP NOSWL, SET BTSEP
NO
YES
TRUE
FALSE
TRUE
DN0933412 Issue 01673
BTSplus mainline commands at the Flexi BSC product family
p
Id:0900d805805b2e37
p
PCCCHLDIperiodCcchLoadIndication(sec)
This attribute indicates the frequency with which the CCCH load indication is sent to the Flexi BSC product line. This attribute is also used to enable the Paging Overload Han-dling.
The value 0 has following two meanings:
• The CCCH Load Indication message is sent only once, every time an overload occurs, with no repetition (frequency = 0)
• The feature Paging Overload Handling is not enabled
Validity Range
Default Value 255 seconds
Contained in the following commands: GET BTS
PEERADDRpeerAddress
Peer IP address of the Circuit Emulation Service Tunnel.The address is input in the usual IPv4 format. The object must be locked before modifying the address via the SET command. For addressing examples see description for attribute ipAddress.
Validity Range
Default ValueNone.
Contained in the following commands: CREATE CESTUNNEL, GET CESTUNNEL, SET CESTUNNEL
PEERUDPPORTpeerUdpPort
Peer UDP port number of the CESPW instance. It is recommended to use identical port numbers for the local and the peer UDP port. The object must be locked before modify-ing the port number via the SET command.
0 - 255
7..15 characters string
674DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805b2e37
p
Validity Range
Default ValueNone.
Contained in the following commands: CREATE CESPW, GET CESPW, SET CESPW
PKTLATpacketizationLatency
The attribute defines the number of frames which are contained in the payload of each UDP packet.
The latency is expressed in micro seconds. Every 125 μsec correspond to 1 TDM frame in the payload. A lower value means a lower delay but a bigger protocol overhead. The object must be locked before modifying the latency value via SET command.
Validity Range
Default Value
Contained in the following commands: CREATE CESPW, GET CESPW, SET CESPW
PNGFpingFrequency
The attribute is only meaningful if the ping delay measurement is activated via the PM scanner SCANBTSM - RNDTDELBTS. It defines how many ping request packets are sent per minute.
SCANBTSM provides only ping delay measurement results if the attribute is set to a value greater than 0.
Validity Range
49152 - 65535
m125
m500
m1000
m2000
m3000
m4000
m5000
m1000
0 - 120
DN0933412 Issue 01675
BTSplus mainline commands at the Flexi BSC product family
p
Id:0900d805805b2e37
Default Value
Contained in the following commands: CREATE CESTUNNEL, GET CESTUNNEL, SET CESTUNNEL
PNGPKTpingPacketSize
The attribute is only meaningful if the ping delay measurement is activated via the PM scanner SCANBTSM - RNDTDELBTS. It defines the size of a ping request packet. The value small corresponds to the default packet size of the ICMP ping request. Value traffic corresponds to the maximum packet size within the pseudo wires of the tunnel.
Validity Range
Default Value
Contained in the following commands: CREATE CESTUNNEL, GET CESTUNNEL, SET CESTUNNEL
PNOFACCHperiodNotificationFACCH(sec)
The attribute defines the period (repetition rate) for the FACCH notification for a given ASCI call.
A change of the attribute becomes effective at expiration of the current time period, latest after the time given by "periodNotificationFACCH".
Validity Range
Default Value 2.5 seconds
Contained in the following commands: GET BTS
PRDINFproductInfo(prodNbr_SN_HwVer_SwVer)
0
SMALL
TRAFFIC
TRAFFIC
1.0 - 5.0
676DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805b2e37
p
The attribute shows product specific information of the TMA if HDLC signaling is used and information is provided by the TMA. It is represented by a single string, consistingof four parts, separated by a couple of defined delimiters:
• Delimiter1 • Delimiter2 (a white space)
This attribute will be retrieved by own command get TMA prodInfo.
Validity Range
Default ValueNone.
Contained in the following commands: GET TMA, GET TMA PRODUCTINFO
PRDIRECTpreferredDirection
The attribute indicates whether the RX downlink information is gained from the related BPORT or not. In a loop configuration the preferred direction is changed, if e.g. the Bit Error Rate is greater than a certain threshold or if the link fails.
'TRUE' means that the RX data at the given BPORT instance is used as input data.
'FALSE' means that the RX data at the given BPORT instance is not used as input data.
The attribute is meaningful only in a loop configuration. If a GET is done in other config-urations the length will be set to 0.
Validity Range
Default ValueNone.
Contained in the following commands: GET BPORT
PRSproceduralStatus
This attribute is contained in all equipment related managed objects. It indicates whether the assigned HW board performs an initialization procedure. For non processor HW boards, the proceduralStatus is always NULL.
This attribute is readable by the operator but is not contained in the "Changed State Event Report" notification.
0..77 characters string
TRUE
FALSE
<NULL>
DN0933412 Issue 01677
BTSplus mainline commands at the Flexi BSC product family
p
Id:0900d805805b2e37
Validity Range
Default Value NULL
Contained in the following commands: GET ACDCP, GET ACT, GET BATTERY, GET BCOM, GET BPORT, GET BTSEP NOSWL, GET CESPW, GET CESTUNNEL, GET COBA, GET COBAETHINTF, GET COSA, GET CU, GET DIDCTMA, GET DILNA, GET DUAMCO, GET DUDCTMA, GET DULNA, GET DUVSWR, GET ENVABTSE, GET ETHCON, GET ETHPORT, GET F6DCTMA, GET F6LNA, GET F6TNFP, GET F6VSWRP, GET FANP, GET FCUMAIN, GET FCUTR, GET FTNFP, GET FVSWRP, GET LAPDLE, GET RACK, GET SYNCBTSE, GET TMA, GET XCONNECT
PSTATportStatus
This attribute provides the result of the auto negotiation procedure. If auto negotiation is disabled the current setting of the port is shown.
Validity Range
Default ValueNone.
Contained in the following commands: GET ETHPORT
PUSGportUsage
This attribute determines usage of the Ethernet port for the BTSplus mainline. Only one ETHPORT instance can be set to BSClink. The attribute is only informational.
Validity Range
NULL
initializing
speed speed100M
speed1000M
duplexMode disabled
enabled
flowControl disabled
enabled
bscLink
multidropLink
678DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805b2e37
p
Default ValueNone.
Contained in the following commands: CREATE ETHPORT, GET ETHPORT, SET ETHPORT
PWNAMEpwName
This attribute specifies optional symbolic name of the pseudo wire, the same name should be configured at the peer side. The name has to be unique within all CESPW instances on given host.
Validity Range
Default ValueNone.
Contained in the following commands: CREATE CESPW, GET CESPW, SET CESPW
PWROUTpowerOutputThresholds
The attribute value is indicated in dB.
The letter "m" before the value range values, means minus
Validity Range
1..80 characters string
This attribute defines the three power output thresholds:
- Output Power Fault Threshold: defines the minimal output power level "transmitter-fault", which results in generating an alarm.
- Reduced Output Power Threshold: defines the power level, when an alarm (warning) is generated (Pout alm red) due to less output power.
- Excessive Output Power Threshold: defines the power level, when an alarm is generated (Pout alm fault) due to too much power level at the output of the power amplifier.
oPwrFaultThreshold m10db
m8db
redOutPwrThresh-old
m10db
m8db
DN0933412 Issue 01679
BTSplus mainline commands at the Flexi BSC product family
p
Id:0900d805805b2e37
Default Value m10dB = -10dB
m6db = - 6dB
db5 = 5dB
Contained in the following commands: GET BTS
PWRREDtxPwrMaxReduction(*-2dB)
This attribute specifies the number of 2dB steps the TRX should be reduced from the maximum transmit power, for tuning the cell coverage. The resulting attenuated transmit power is the maximum nominal power Pn.
(values from 0 dB to -12 dB, with step size - 2 dB)
Validity Range
Default ValueNone.
Contained in the following commands: GET TRX
m6db
m4db
excesOutPwrThresh db3
db5
0 - 9
680DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805b2e39
r
r
RACHBTrachBusyThreshold(dBm)
Validity Range
Default Value 109
Contained in the following commands: GET BTS
RACHLASrachLoadAveragingSlots
This attribute defines the number of RACH bursts over which RACH measurements are performed.
Validity Range
Default Value 204 = 4 CCCH multiframes
Contained in the following commands: GET BTS
RADIOMGradioMeasGran
This is an attribute of the TRX and specifies the granularity (multiples of 480 ms) in which the radio measurements have to be transmitted on the Abis interface in case they are enabled.
The attribute is indicated in SACCH multiframes.
This attribute defines a threshold for the received signal level con-cerning both:
- RACH access bursts
- intercell HO access bursts.
A signal level exceeding this threshold is interpreted as a busy RACH respective as a valid burst due to an intercell HO.
<ANY>
102 - 65535
DN0933412 Issue 01681
BTSplus mainline commands at the Flexi BSC product family
r
Id:0900d805805b2e39
Validity Range
Default Value 254 in SACCH multiframe
Contained in the following commands: GET TRX
RADIOMRradioMeasRep
(ON = enabled)
Validity Range
Default Value OFF (disabled)
Contained in the following commands: GET TRX
RADIUSEXTradiusExtension(km)
This attribute identifies the radius extension (in km) of an extended cell.
1 - 254
This is an attribute of the TRX and specifies whether the radio mea-surements have to be transmitted on the Abis interface.
Notes:
- A consequence of the value 'disabled' is that no 'Measure-ment result' messages are sent to the Flexi BSC product line.
- Special care has to be applied if the attribute is set to "ON" for several TRXs: the appropriate Abis signalling capacity must be provided by creating a sufficient number of LAPDLE instances each with a full 64 KBit/s timeslot. If this prerequisite is not fulfilled (e.g. just 1 LAPDLE and 11 TRXs with full and half rate are fully exploited) the Call Failure Rate will increase (increased delay times in the BTSE LAPD queues due to the huge amount of measurement result messages lead to more CHANNEL REQUIRED messages because of a too late Immediate Assignment command etc. etc.). This is especially critical if RADIOMG is set to 1 (corresponding to 480 ms).
OFF
ON
682DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805b2e39
r
Validity Range
Default ValueNone.
Contained in the following commands: GET BTS, GET TRX
RELEQUIPOBJrelatedEquipObjects
Validity Range
Default ValueNone.
Contained in the following commands: GET BTS, GET BTSM NOSWL, GET CHAN, GETRELATIONSHIP TRX
RELFUNCOBJrelatedFuncObjects
0 - 35
This attribute represents the relationships between a specific FMO instance and none, one or several HMO instances. The HMO instances in this list offers their services to the given FMO instance. This attribute is only allowed for BTSM, BTS, TRX and CHANNEL objects.
FMO maximal number of related HMOs
N (decimal)
BTS 0 2
BTSM 1 6
CHAN 0 2
TRX 30 122
0 to 47 items of
Pathname
DN0933412 Issue 01683
BTSplus mainline commands at the Flexi BSC product family
r
Id:0900d805805b2e39
This attribute represents the relationships between a specific HMO instance and none, one or several FMO instances. The FMO instances in this list make use of the services of the given HMO instance. This attribute is allowed for each HMO instance of the actual hardware variant. Currently only BTSM and TRX are contained in the list.
Since the maximal number of related FMO instances in the list depends on the special type of HMO, the following list shows the real-istic values for the each HMO that may contain related FMO instances. The table shows for each HMO the maximal number of FMO instances and the maximum number of octets of the attribute including the attribute identifier and attribute length field.
HMO maximal number of related FMOs
N (decimal)
BPORT 0 2
BTSE 1 6
ENVABTSE 0 2
LAPDLE 0 2
RACK 0 2
SYNCBTSE 48 194
XCONNECT 0 2
HMO maximal number of related FMOs
N (decimal)
ACDCP 0 2
ACT 0 2
BATTERY 0 2
COBA 48 194
COSA 24 (note) 98
CU 1 6
DIDCTMA 24 98
DILNA 24 98
DUDCTMA 24 98
DULNA 24 98
DUVSWR 24 98
FANP 0 2
FCUMAIN 2 10
FCUTR 1 6
684DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805b2e39
r
Validity Range
Default ValueNone.
Contained in the following commands: GET ACDCP, GET ACT, GET BATTERY, GET BCOM, GET BPORT, GET BTSEP NOSWL, GET CESPW, GET CESTUNNEL, GET COBA, GET COBAETHINTF, GET COSA, GET CU, GET DIDCTMA, GET DILNA, GET DUAMCO, GET DUDCTMA, GET DULNA, GET DUVSWR, GET ENVABTSE, GET ETHCON, GET ETHPORT, GET F6DCTMA, GET F6LNA, GET F6TNFP, GET F6VSWRP, GET FANP, GET FCUMAIN, GET FCUTR, GET FTNFP, GET FVSWRP, GET LAPDLE, GET RACK, GET SYNCBTSE, GET TMA, GET XCONNECT, GETRELATIONSHIP BCOM, GET-RELATIONSHIP COBA
REPTYPreportType
This parameter is used to indicate to the mobile station to use the ENHANCED MEA-SUREMENT REPORT or MEASUREMENT REPORT messages for reporting, and it can assume two values:
- NORMAL: the MS uses the MEASUREMENT REPORT message for reporting
- ENHANCED: the MS uses the ENHANCED MEASUREMENT REPORT message for reporting if at least one BSIC (Base Station Identity Code) is allocated to each frequency of the BA (BCCH Allocation) list . Otherwise, the MEASUREMENT REPORT message is used.
Validity Range
Default ValueNone.
FTNFP 1 6
FVSWRP 8 34
TMA 24 98
Note: COSA old (if enableFcuSupport = TRUE) and COSA new only can handle up to 12 FCU (24 TRX)
0 to 48 items of
Pathname
ENHANCED
NORMAL
ENHANCED_ONLY_FOR_R43G_MS
DN0933412 Issue 01685
BTSplus mainline commands at the Flexi BSC product family
r
Id:0900d805805b2e39
Contained in the following commands: GET BTS
RFRSINDPrfResourceIndicationPeriod
This attribute indicates the sending rate of the signalling message RF RES IND to the Flexi BSC product line.
The attribute is indicated in unit of SACCH multiframes
Validity Range
Default Value 60 in unit of SACCH multiframe
Contained in the following commands: GET BTS
RSACCHRXLDLrepSacchRxLevDL
This attribute is used to define, on a per cell basis, the threshold for RXLEV_DL_SUB used in the decision algorithm for activating R-SACCH in DL and UL for MS with Repeated SACCH Capability, i.e. R-ACCH_CAP = 1.
Validity Range
Default ValueNone.
Contained in the following commands: GET BTS
RSACCHRXLULrepSacchRxLevUL
This attribute is used to define, on a per cell basis, the threshold for RXLEV_UL_SUB used in the decision algorithm for activating R-SACCH in DL and UL for MS with Repeated SACCH Capability, i.e. R-ACCH_CAP = 1.
Validity Range
1 - 254
0 - 25
0 - 25
686DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805b2e39
r
Default ValueNone.
Contained in the following commands: GET BTS
RSACCHTODLrepSacchTimeOutDL
This attribute is used to define, on a per cell basis, the threshold for deactivation of R-SACCH mode in the decision algorithm for R-SACCH in DL for MS with Repeated SACCH Capability, i.e. RACCH_CAP = 1.
Validity Range
Default ValueNone.
Contained in the following commands: GET BTS
RSACCHTOULrepSacchTimeOutUL
This attribute is used to define, on a per cell basis, the threshold for deactivation of R-SACCH mode in the decision algorithm for R-SACCH in UL for MS with Repeated SACCH Capability, i.e. RACCH_CAP = 1.
Validity Range
Default ValueNone.
Contained in the following commands: GET BTS
RXBMAXFrxBandMaxFreq(kHz*100)
Attribute data provided by TMA.
Validity Range
0 - 10
0 - 10
0 - 65535
<NULL>
DN0933412 Issue 01687
BTSplus mainline commands at the Flexi BSC product family
r
Id:0900d805805b2e39
Default ValueNone.
Contained in the following commands: GET TMA
RXBMINFrxBandMinFreq(kHz*100)
Attribute data provided by TMA.
Validity Range
Default ValueNone.
Contained in the following commands: GET TMA
RXDIVSVenableRxDiversitySupervision
The attribute enableRxDiversitySupervision of the object 'BTSE' indicates whether the supervision of the RX levels and the signal to noise ratio of both receiver branches is enabled or disabled. A prerequisite is that diversity is configured and that a TCH or SDCCH is on at least 2 time slots of the TRX. Due to the supervision failure event reports for the TPU / CU related to a TRX may be sent.
Validity Range
Default Value
Contained in the following commands: GET BTSEP NOSWL, SET BTSEP
RXLEVADJrxLevAdjust(dB)
This attribute specifies the value needed to adjust the RXLEV value of both receiver branches ("N" and "D") of the TPU, CU and of the FCUMAIN.
The attribute has no functionality in case a FCUMAIN is wired to a SDUAMCO.
0 - 65535
<NULL>
disabled
enabled
disabled
688DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805b2e39
r
(values from -24 dB to +23 dB)
Validity Range
Default Value
Contained in the following commands: CREATE CU, CREATE FCUMAIN, GET CU, GET FCUMAIN, SET CU, SET FCUMAIN
RXLEVADJN1D1rxLevAdjustN1D1(dB)
This attribute specifies the value needed to adjust the RXLEV value of the additional receiver branches "Rx C / N1" and "Rx D / D1" of the FCUMAIN.
The attribute has no functionality in case a FCUMAIN is wired to a SDUAMCO).
Validity Range
Default Value
Contained in the following commands: CREATE FCUMAIN, GET FCUMAIN, SET FCUMAIN
RXSIGLEVADJrxSigLevAdjust
The attribute specifies the signal level adjust values which shall be applied to the receive paths of transceivers using the same frequency band as the BCCH transceiver.
Validity Range
Default ValueNone.
adjustValue -24.0 - 24.0
adjustDivValue -24.0 - 24.0
adjustValue 0.0
adjustDivValue 0.0
adjustValueN1 -24.0 - 24.0
adjustDivValueD1 -24.0 - 24.0
adjustValueN1 0.0
adjustDivValueD1 0.0
<ANY>
DN0933412 Issue 01689
BTSplus mainline commands at the Flexi BSC product family
r
Id:0900d805805b2e39
Contained in the following commands: GET BTS
RXSIGLEVADJCrxSigLevAdjustCompl
The attribute specifies the signal level adjust values which shall be applied to the transmit paths oftransceivers using the complementary frequency band. The value is only meaningful in case of a multiband cell.
Validity Range
Default ValueNone.
Contained in the following commands: GET BTS
RXSWCURSETrxSwitchCurrentSetting
Usually the content of this attribute is identical to the value of the attribute rxSwitchReq-Setting. A deviation is possible e.g. in case of HW failures - in these cases the attribute shows the real situation. The attribute has a meaning only if the value of the attribute switchedBeamCapability has the value four_beams.
The BTSplus mainline sends a change of the attribute value via CAER to the Flexi BSC product line.
Validity Range
Default ValueNone.
Contained in the following commands: GET BTS
<ANY>
NULL
690DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805b2e3b
s
s
SALUNAMEsalesUniqueName
Validity RangeIn commands GET BTSEP NOSWL:
In commands SET BTSEP:
Default Value length = 1, octet 3 = 0
Contained in the following commands: GET BTSEP NOSWL, SET BTSEP
SBPRTsyncBport
This attribute indicates the port which is currently used for synchronization. This infor-mation is specially useful in case of a PCM loop configuration.
Validity Range
Default ValueNone.
Contained in the following commands: GET SYNCBTSE
SCELLNOsecondCellNumber
The attribute contains an ASCII string with 11 characters which don't contain a NUL character. The operator has always to enter 11 char-acters for the attribute. If the operator has not yet supplied a value for the attribute but does a GET, the BTSplus mainline SW will return the 'default value'. The attribute should be set by the operator before a upload of the IDT is performed.
The attribute is also used during the Abis alignment for checking if the right BTSplus mainlineis connected to the Abis link.
Default Value: length = 1, octet 3 = 0
1..11 characters string
11..11 characters string
<ANY>
DN0933412 Issue 01691
BTSplus mainline commands at the Flexi BSC product family
s
Id:0900d805805b2e3b
This attribute allows to indicate a second cell number for the objects DILNA and DULNA. Value <FF> means that a secondCellNumber is not used.
The second cell number allows sharing an antenna for receive diversity, i.e. it allows that two cells with different MNC (Mobile Network Code) which cover the same area (e.g. the same sector) at the BTSplus mainline site can share the same DUAMCO/FDUAMCO or IAMCO if receive diversity is required. As a consequence a DULNA-, DILNA- or TMA instance may belong to two cells.
The relation between a carrier unit and cell is derived from the TX wiring only, i.e. the attribute cellNumber of the wired DUVSWR object determines the cell a CU/FCUTR belongs to. The BTSplus mainline checks for each CU that one of the attributes cellNum-ber and secondCellNumber of all wired DULNA/DILNA objects matches with the attri-bute cellNumber of the wired DUVSWR.
It is strongly recommended to ensure for each CU/FCUTR that the attribute cellNumber of one wired DULNA object matches with the cellNumber of the wired DUVSWR.
Validity Range
Default ValueNone.
Contained in the following commands: CREATE DILNA, CREATE DULNA, CREATE F6LNA, GET DILNA, GET DULNA, GET F6LNA, SET DILNA, SET DULNA, SET F6LNA
SCIDsectorId
Attribute data provided by TMA.
Validity Range
N_00
N_01
N_02
N_03
N_04
N_05
N_06
N_07
N_08
N_09
N_10
N_11
NotUsed
0..32 characters string
692DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805b2e3b
s
Default ValueNone.
Contained in the following commands: GET TMA
SCLPRIOLSTserviceClassPrioList
Default settings of this attribute for CES service correspond to “expedited forwarding”:
List of up to 8 service classes. Currently only the service class CES is supported. When the CES value is set for serviceClass all other attributes must not be set to default val-ues.Maximum one list entry is allowed for each service class.
Validity RangeIn commands GET BTSEP NOSWL:
Service Class CES Service Class to which the priority settings apply
vlanPrio 7 This attribute is not relevant if vlanid is set to “NULL.”
dscpClass 5 DSCP class selector. The value is the decimal representation of DSCP bits 0-2
dscpDropPre 6 DSCP drop precedence. The value is the decimal representation of DSCP bits 3-5
Table Default settings for CES service
0 to 8 items of
serviceClass ces
vlanPrio vPrio0
vPrio1
...
vPrio7
dscpClass dCl0
dCl1
...
dCl7
dscpDropPre dDP0
dDP1
...
dDP7
<NULL>
DN0933412 Issue 01693
BTSplus mainline commands at the Flexi BSC product family
s
Id:0900d805805b2e3b
In commands SET BTSEP:
Default ValueIn moc(s) BTSEP:
None.
In moc(s) BTSEP:
Contained in the following commands: GET BTSEP NOSWL, SET BTSEP
SEGMENTIDsegmentId
This attribute holds the “cellNumber” (from BR HMO data) parameter (configured by the user) to define the mapping of BTS instances to combiner equipment according HW configuration. The same “cellNumber” has to be set for all BTS in a segment. If a wrong value has been set by the user, either no HW (the alarm “HW cannot be assigned” is generated) or wrong HW is used for the BTS instance. In this case the underying FMOs must be deleted and created again with correct “cellNumber”.
g Since this attribute is reused to ensure a 1:1 mapping with the HW configuration within BSxx, there is a different view of segment Id as seen on BSS Abis (segment Id, range 0..3000) and LMT Evolution (“cellNumber”, range 0..11).
1 to 8 items of
serviceClass ces
vlanPrio vPrio0
vPrio1
...
vPrio7
dscpClass dCl0
dCl1
...
dCl7
dscpDropPre dDP0
dDP1
...
dDP7
serviceClass ces
vlanPrio vPrio7
dscpClass dCl5
dscpDropPre dDP6
694DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805b2e3b
s
Validity Range
Default ValueNone.
Contained in the following commands: GET BTS
SFPSERIDsfpSerialId
This attribute represents serial Id data if a SFP module is equipped.
The attribute is only meaningful for ports with SFP cages, i.e. it is not relevant for the ETHPORT instances 0 and 1.
The structure of the octet string is compliant to the addresses 0 â?? 127 of the Serial ID data at address A0.
Validity Range
Default ValueNone.
Contained in the following commands: GET ETHPORT
SHLAPDITshortLapdIntTimer(sec)
The BTSplus mainline uses the value of this timer to calculate the value of timer T202 which is used for the TEI assignment procedure.
This attribute is the timer used by the Flexi BSC product family in case of Abis link failure in order to discriminate between a "fast alignment" or a "full alignment". With the detec-tion of the link failure (which may happen at different times in BTSplus mainline and Flexi BSC product family) the BTSplus mainline starts the timer 'omLAPDRelTimer' and the Flexi BSC product family starts the timer 'shortLAPDIntTimer'. If any LAPD link on any of the LAPDLE signalling timeslots is up again within a certain time (i.e. the timer 'short-LAPDIntTimer' in the Flexi BSC product family has not yet expired) the Flexi BSC product family may decide to perform the fast alignment procedure.
At the detection time of the Abis link failure the BTSplus mainline starts the timer omLAPDRelTimer and the Flexi BSC product family starts the timer shortLAPDIntTimer. If the timer omLAPDRelTimer expires, the BTSplus mainline blocks the call processing. After that the BTSplus mainline forces the Flexi BSC product family (via a Restart Sending Event Reports NACK message) to perform a complete Abis alignment. If none of the two timers expires, the Flexi BSC product family performs a 'Short Abis alignment'.
0 - 11
0 to 128 items of
H#0 - H#ff
DN0933412 Issue 01695
BTSplus mainline commands at the Flexi BSC product family
s
Id:0900d805805b2e3b
(step size 1 second)
Validity Range
Default Value 15 seconds
Contained in the following commands: GET BTSM NOSWL
SLOTNOslotNo
The attribute indicates the slot number of the COBA and COSA. Since the modelling of the MO COBA is fixed (active COBA/COSA always COBA(0)/COSA(0), passive COBA/COSA always COBA(1)/COSA(1)), this is the only way to find out the slot of the active / passive COBA/COSA.
Validity Range
Default ValueNone.
Contained in the following commands: GET COBA, GET COSA
SRADIUSEXTsuperRadiusExtension(km)
This attribute defines the distance (measured in km) of the inner edge of 35 km wide super extended area from the BTS. Thevalue “0” means that the super extended area is not in use.
Validity Range
Default ValueNone.
Contained in the following commands: GET BTS
3 - 20
leftCOBA
rightCOBA
leftCOSA
rightCOSA
0 - 70
696DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805b2e3b
s
SRCDIRsourceDir
Validity Range
Default ValueNone.
Contained in the following commands: DNLIDFD REMINV
SRCPATHsrcpath
The sourceDirectory indicates the directory containing the BTS-SW to be downloaded (DNLALLEXE).
Validity Range
Default ValueNone.
Contained in the following commands: DNLALLEXE SOFTWARE-MANAGEMENT
STATIMEstartingTime
This attribute is only used together with btsIsHopping and can not be set by the operator.
Current Frame No is a binary presentation Frame Number Modulus 42432.
Note: startingTime is only used together with btsIsHopping.
Validity Range
Default ValueNone.
The sourceDirectory indicates the directory containing the BTS-SW to be downloaded (DNLALLEXE).
The sourceDirectory indicates the directory containing the BTSE nob-RIU file to be downloaded (DNLIDFD).
1..80 characters string
1..92 characters string
0 - 65535
<NULL>
DN0933412 Issue 01697
BTSplus mainline commands at the Flexi BSC product family
s
Id:0900d805805b2e3b
Contained in the following commands: GET BTS TIMER
STDBYSTstandbyStatus
The resource is not providing service but is able to take over the role of the resource to be backed-up without an initialization. The resource is providing service and is backing up another resource.
Validity Range
Default ValueNone.
Contained in the following commands: GET COBA, GET COSA, GET CU, GET FCUTR, GET LAPDLE
SUBUNTsubUnitType
new information
Validity Range
Default ValueNone.
Contained in the following commands: GET TMA
SWBCAPABILITYswitchedBeamCapability
This attribute reflects the capability of the BTSplus mainline hardware and software. A change of the attribute value is sent by the BTSplus mainline via CAER to the Flexi BSC product family.
- unknown means the BTSplus mainline is not yet fully configured.
Reserved
ColdStandBy
ProvidingService
NULL
vswr
bypass
<NULL>
698DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805b2e3b
s
- none means the BTSplus mainline hardware and/or software does not support switched beams.
- four_beams means the BTSplus mainline hardware and software supports 4 switched beams.
Validity Range
Default ValueNone.
Contained in the following commands: GET BTS
SWBSERVSTATEswitchedBeamServState
The attribute indicates the current state of the switched beam functionality. A change of the attribute value is sent by the BTSplus mainline via CAER to the Flexi BSC product family. The values have the following meaning:
NULL Initial value if BTSplus mainline is not aligned or default value if the BTSplus mainline types does not support switched beams.
Validity Range
Default ValueNone.
Contained in the following commands: GET BTS
SWLCFIDswLoadCurrentFileId
This attribute contains the fileID (name of the SW load, 12 byte) of the software load that is currently running in the BTSplus mainline. A SW load is the SW for the whole NE, that is able to run on the processors of the NE at the same time. It consists of a certain number of SW images, that are not shown to the user for the BTSplus mainline.
Notes on validity range:
ASCII String: 'HScnvvss.SWL" (swLoad-header file), where:
none
NULL
DN0933412 Issue 01699
BTSplus mainline commands at the Flexi BSC product family
s
Id:0900d805805b2e3b
cn Version part (network operator code)
01 = Ciphering A5.0 + A5.1 + A5.2
02 = Ciphering A5.0 + A5.2 12
03 = Ciphering A5.0 only
vv Version part (feature package code)
ss Version part (actual state)
Validity Range
Default ValueNone.
Contained in the following commands: GET BTSM SWL
SWLCVERswLoadCurrentFileVersion
This attribute contains the version number of the software load (26 bytes) that is cur-rently running in the BTSplus mainline. Under normal operation conditions it is the same as the version number of the swLoadIntended (SWLDINT). If the latter SW load is cor-rupted, the swLoadCurrentVersion is identical to the version number of the swLoad-Safety (SWLDSAF) or the version number of the third SW load that is stored in the BTSplus mainline (the dischargeable one). It is guaranteed that only SW loads are auto-matically started by the BTSplus mainline, which have been executed on that BTSplus mainline before.
Notes on validity range:
ASCII String:cn-hh-vv-ii-ss-pp_yy-mm-dd, where:
cn Version part (network operator code)
01 = Ciphering A5.0 + A5.1 + A5.2
02 = Ciphering A5.0 + A5.2 12
03 = Ciphering A5.0 only
hh Version part (HW/SW compatibility code)
01 = BS20, BS21E, BS60, BS61E or BS22
04 = BS240, BS241, BS240XL, BS240SR, BS241SR,
BS240XLSR, BS40, BS40II, BS41, BS82II, BS82,
BS240XS, BS288
vv Version part (feature package code)
ii Version part (sub-feature package code)
12..12 characters string
700DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805b2e3b
s
00 = independent (e.g. loadable boot/test SW
01 = BS240, BS241, BS240XL, BS40, BS40II, BS41,
BS82II
05 = BS82
06 = BS240XS, BS288
ss Version part (actual state)
pp Patch version (usually 00)
yy-mm-dd production date (optional)
Validity Range
Default ValueNone.
Contained in the following commands: GET BTSM SWL
SWLDINTswLoadIntended
This attribute is divided into 2 parts and defines the file ID (=file name) and version number of the SW load stored in the BTSplus mainline, that has been activated over the Abis- or T-interface with the latest 'Activate SW' message. This SW load is automatically activated from the BTSplus mainline firmware at power on time.
The file ID (= file ID for a SW load) and the version number () are supplied by the BTSplus mainline after the 'Activate SW' message was sent. The value for both parts is 'not valid', if there was no 'Activate SW' message before, or "swLoadCurrent", if the intended SW load is corrupted.
Notes on validity range:
swLoadIntendedFileId: Coding according to swLoadCurrentFileId
Default Value: 0"filename.ext"
Octet #15 contains the ASCII character ":".
swLoadIntendedVersion: Coding according to swLoadCurrentVersion
Default Value: "cn-hh-vv-ii-ss-pp_yy-mm-dd"
The value 'not valid' for this attribute is indicated via '0' as byte 3.
Validity Range
26..26 characters string
39..39 characters string
DN0933412 Issue 01701
BTSplus mainline commands at the Flexi BSC product family
s
Id:0900d805805b2e3b
Default ValueNone.
Contained in the following commands: GET BTSEP SWL
SWLDSAFswLoadSafety
This attribute is divided into 2 parts and describes the file ID (= file ID for a SW load) and the version number () of the SW load stored in the BTSplus mainline, that is identified by the operator at the OMC or LMT Evolution (via a 'Set Attribute' message at the Abis- or T- interface or a M-SET service at the O-interface) as the most trusted SW load (in the sense of its ability to handle the Abis-link to build up a connection to the Flexi Flexi BSC product family product family). It is used if the swLoadIntended is damaged in some way. There is no alignment to one of the SW loads stored on the Flexi Flexi BSC product family product family master database. It is even not necessary, that this SW load is stored in the Flexi Flexi BSC product family product family master database. The iden-tification of a SW load as the safety one is only accepted by the BTSplus mainline, if the identified load has been activated and executed on this BTSE before. It is recommended that an update of the attribute is performed in each release and that the swLoad of the previous release is used as 'swLoadSafety'.
The value 'not valid' indicates that the safety SW load is corrupted or has not been iden-tified by the operator.
Notes on validity range:
swLoadSafetyFileId: Coding according to 'swLoadCurrentFileId'
default value: 0"filename.ext"
Octet #15 contains the ASCII character ":".
swLoadSafetyVersion: Coding according to 'swLoadCurrentVersion'
default value: "cn-hh-vv-ii-ss-pp_yy-mm-dd"
The value 'not valid' for this attribute is indicated via '0' as byte 3.
Validity Range
Default ValueNone.
Contained in the following commands: GET BTSEP SWL, SET BTSEP
SWLDSTswLoadsStored
39..39 characters string
702DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805b2e3b
s
This attribute contains the file IDs (= file ID for a SW load) and version numbers of up to three SW loads, that are stored in the Flash Eprom. The attribute is divided into 3 main parts, each part split up in the fileID and file version of one SW load.
In principle there are two different 'kinds' of values for one load version: one indicating the file ID and load version number of the SW load of the BTSplus mainline, that has been successfully downloaded and that has been recognized by the BTSplus mainline as a complete load; the second one, the 'not valid' value, indicating that no load has been downloaded into that partition of the Flash Eprom, or that the download is not com-plete, or that the stored SW load is corrupted as the check sum is not correct any more.
Octets #15, #55 and #93 contain the ASCII character ":".
The value 'not valid' is indicated as 0 (hexadecimal) for the octets #3 or #42 or #81.
Validity Range
Default ValueNone.
Contained in the following commands: GET BTSEP SWL
SYNCHROsynchro
new information
Validity Range
Default ValueNone.
Contained in the following commands:None.
SYNCSRCsyncSource
This attribute specifies the preferred synchronization source, i.e. whether the BTSplus mainline should be synchronized via Abis or to a 3rd party GPS receiver.
If the attribute value is extGPS further following attributes become relevant:
• enableInterSiteSync • burstNumberOffset • frameNumberOffset
3 to 3 items of
39..39 characters string
NO
YES
DN0933412 Issue 01703
BTSplus mainline commands at the Flexi BSC product family
s
Id:0900d805805b2e3b
• maxPhaseError • maxResyncTime
By setting the syncSource attribute to ext_1pps_only the BTSE 1 is synchronized to an external device which delivers 1pps pulses. There is no switching to a secondary syn-chronization source if the 1pps signal fails.
The attribute "1pps only" is supported only for COBA4P12v2 and CESCOBA.
Validity Range
Default Value
Contained in the following commands: GET SYNCBTSE, SET SYNCBTSE
SYNCSTATsyncState
This attribute indicates the details of the synchronisation process of the BTSplus main-line.
Validity Range
Default ValueNone.
Contained in the following commands: GET SYNCBTSE
SYSIDcellAllocationNumber
This attribute indicates the frequency band used by the traffic channels.
abis
extGPS
ext_1pps_only
abis
init
ready
abis
abisHoldMode
syncUnit
syncUnitHoldMode
704DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805b2e3b
s
Validity Range
Default ValueNone.
Contained in the following commands: GET BTS
BB900
DCS1800
F2ONLY900
EXT900
PCS1900
GSMR
GSMDCS
GSM850
GSM850PCS
GSM850DCS
DN0933412 Issue 01705
BTSplus mainline commands at the Flexi BSC product family
t
Id:0900d805805b2e3d
t
T200t200
This attribute contains values for the LapDm timer T200 to be used on different control channels.
Validity Range
Default ValueSDCCH 29 ms
FACCH/Full rate 31 ms
FACCH/Half rate 38 ms
SDCCH SAPI3 90 ms
SACCH with TCH SAPI0 70 ms
SACCH with SDCCH 29 ms
SACCH with TCH 168 ms
Contained in the following commands: GET BTS TIMER
T3105btsTimer3105(*10ms)
This attribute contains the value of the timer T3105, which is used for the repetition of the PHYSICAL INFORMATION message.
The attribute step size is 10 msec.
Validity Range
Default Value 1 (corresponding to 10 ms)
Contained in the following commands: GET BTS
sdcchSAPIO 0 - 255
facchTCHF 0 - 255
facchTCHH 0 - 255
saccchTCHSAPIO 0 - 255
sacchSDCCH 0 - 255
sdcchSAPI3 0 - 255
sacchTCHSAPI3 0 - 255
1 - 254
706DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805b2e3d
t
T3115t3115(*10ms)
T3115 is a timer to define the repetition rate of sending the VGCS UPLINK GRANT message. In case of a ASCI-call the network grants the uplink to one mobile station by sending a VGCS UPLINK GRANT message to the mobile station. After having sent this message the BTSplus mainline starts T3115 to repeat this message as long as a counter not reached the value of ny2 or a correctly decoded frame was received.
(value indicated in milliseconds; step size 10 ms)
Validity Range
Default Value 4 (corresponding to 40 ms)
Contained in the following commands: GET BTS TIMER
T3151uplBusyRepRate
This attribute determines the repetition rate for the “upl_busy” message per cell. Default suggested value: 3 sec.
Validity Range
Default ValueNone.
Contained in the following commands: GET BTS
TAADJtaAdjust(microseconds)
This attribute takes the propagation delay created on the BTSplus mainline internal signal path into account. It comprises both transmit and receive direction i.e. it is the sum of the transmit delay and the receive delay. The attribute taAdjust refers to the whole cell.
(value indicated in nanoseconds; step size 100 ns).
Validity Range
Default Value 0 (0 nanoseconds)
1 - 254
1 - 9
0.0 - 10.0
DN0933412 Issue 01707
BTSplus mainline commands at the Flexi BSC product family
t
Id:0900d805805b2e3d
Contained in the following commands: GET BTS TIMER
TCCtxCoherentComb
Attribute reserved for future implementation.
Validity Range
Default Value
Contained in the following commands: CREATE FCUMAIN, GET FCUMAIN, SET FCUMAIN
TCCCHLDIthresholdCcchLoadIndication
This attribute is used if the Paging Overload Handling is active in the BTSplus mainline (refer to "periodCCHLoadInd"), to stop the Paging Overload Regulation, when the Paging Load goes below the threshold.
Suggested value is: 50 (hex).
Note that when Paging Overload is active, all Pagings with IMSI are discharged until the Paging Load goes below the threshold.
Note: in case of ASCI enabled in the cell, that is P1 Rest Octets for NCH info are set in Paging Request Type 1, only one IMSI could fit in a Paging Request Type 1 and even though Paging Load is only 50%, there is not enough space for the second IMSI in Paging Request Type 1. In this case it could make sense to set the threshold to lower values but take care that meanwhile all Pagings with IMSI are discharged.
The attribute value is indicated in %.
Validity Range
Default Value 100%
Contained in the following commands: GET BTS
TRUE
FALSE
FALSE
0 - 100
708DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805b2e3d
t
TDMAPtdmMapping
This attribute determines the mapping of the payload data to internal TDM ports of virtual BPORT corresponding to the given instance of CESPW. For each payload time slot (pTs), which is contained in the UDP stream the target time slot number on the virtual bport has to be set. Only subsequent payload time slots beginning with pTs1 can be selected. The value 0 means no mapping.
Validity Range
pTs1 0 - 31
pTs2 0 - 31
pTs3 0 - 31
pTs4 0 - 31
pTs5 0 - 31
pTs6 0 - 31
pTs7 0 - 31
pTs8 0 - 31
pTs9 0 - 31
pTs10 0 - 31
pTs11 0 - 31
pTs12 0 - 31
pTs13 0 - 31
pTs14 0 - 31
pTs15 0 - 31
pTs16 0 - 31
pTs17 0 - 31
pTs18 0 - 31
pTs19 0 - 31
pTs20 0 - 31
pTs21 0 - 31
pTs22 0 - 31
pTs23 0 - 31
pTs24 0 - 31
pTs25 0 - 31
pTs26 0 - 31
pTs27 0 - 31
pTs28 0 - 31
pTs29 0 - 31
DN0933412 Issue 01709
BTSplus mainline commands at the Flexi BSC product family
t
Id:0900d805805b2e3d
Default ValueNone.
Contained in the following commands: CREATE CESPW, GET CESPW, SET CESPW
TEItei
This attribute contains the Terminal Endpoint Identifier used in the layer2 addressing on the Abis-Interface for the logical O&M or Radio Signalling Link.
The values 0..63 of the validity range refers tro the 'Initial TEI'
Validity Range
Default ValueNone.
Contained in the following commands: GET BTSM NOSWL, GET TRX
TESTMODEenableTestMode
This attribute determines whether transceiver test mode can be activated. This is only possible for non BCCH transceivers if their administrative state is "locked". If the test mode is activated, the transceiver sends dummy bursts on all time slots with the fre-quency dlTestFrequency and the output power reduced by testPowerReduction. All other transceiver attributes are meaningless in test mode in the DL direction. In UL direc-tion the transceiver attributes for normal operation apply.
If the test mode is deactivated, the attributes for normal operation apply in DL direction again and the attributes dlTestFrequency and testPowerReduction are meaningless instead.
Validity Range
Default ValueNone.
pTs30 0 - 31
pTs31 0 - 31
0 - 128
TRUE
FALSE
710DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805b2e3d
t
Contained in the following commands: GET TRX
TESTMONtestMonitor
Up to 6 testMonitorInfo fields can present (depend on the board).
Working phases:
ACDCP PreliminaryTestsAcdcp CU PreliminaryTestsCu
CheckAlarmStatusAcdcp BootEepromTestCu
EndTestAcdcp SerialEepromTestCu
ACT PreliminaryTestsAct LocalTestLoopCu
CheckAlarmStatusAct EndTestCu
EndTestAct DILNA PreliminaryTestsDilna
BATTERY PreliminaryTestsBattery CheckAlarmStatusDilna
CheckAlarmStatusBattery EndTestDilna
EndTestBattery DIDCTMA PreliminaryTestsDidctma
COBA PreliminaryTestsCoba CheckAlarmStatusDidctma
BootEepromTestCoba EndTestDidctma
SerialEepromTestCoba DUDCTMA PreliminaryTestsDudctma
EndTestCoba CheckAlarmStatusDudctma
COSA PreliminaryTestsCosa EndTestDudctma
SerialEepromTestCosa DULNA PreliminaryTestsDulna
EndTestCosa CheckAlarmStatusDulna
EndTestDulna
Working phases:
DUVSWR PreliminaryTestsDuvswr LMU PreliminaryTestsLmu
CheckAlarmStatusDuvswr CheckAlarmStatusLmu
EndTestDuvswr EndTestLmu
FANP PreliminaryTestsFanp FTNFP PreliminaryTestsFtnfp
CheckAlarmStatusFanp CheckAlarmStatusFtnfp
EndTestFanp EndTestFtnfp
FCUMAIN PreliminaryTestsFcumain FVSWRP PreliminaryTestsFvswrp
BootEepromTestFcumain CheckAlarmStatusFvswrp
SerialEepromTestFcu-main
EndTestFvswrp
DN0933412 Issue 01711
BTSplus mainline commands at the Flexi BSC product family
t
Id:0900d805805b2e3d
Validity Range
EndTestFcumain SYNCBTSE PreliminaryTestsSyncbtse
FCUTR PreliminaryTestsFcutr ResyncTestSyncbtse
LocalTestLoopFcutr EndTestSyncbtse
EndTestFcutr TMA PreliminaryTestsTma
CheckAlarmStatusTma
EndTestTma
1 to 6 items of
phaseId PreliminaryTestsAct
PreliminaryTestsCu
PreliminaryTest-sCoba
PreliminaryTests-Cosa
PreliminaryTests-Fanp
PreliminaryTests-Dilna
PreliminaryTestsDu-vswr
PreliminaryTests-Dulna
PreliminaryTests-Battery
PreliminaryTestsB-com
PreliminaryTest-sTma
PreliminaryTests-Dudctma
PreliminaryTests-Didctma
PreliminaryTest-sAcdcp
PreliminaryTests-Fvswrp
PreliminaryTestsFt-nfp
PreliminaryTest-sLmu
712DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805b2e3d
t
PreliminaryTestsS-dulna
PreliminaryTestsS-dusec
PreliminaryTestsS-dusubsec
PreliminaryTestsS-dutxsw
EndTestAct
EndTestCu
EndTestCoba
EndTestCosa
EndTestFanp
EndTestDilna
EndTestDuvswr
EndTestDulna
EndTestBattery
EndTestTma
EndTestDudctma
EndTestDidctma
EndTestFvswrp
EndTestFtnfp
EndTestLmu
EndTestSdulna
EndTestSdusec
EndTestSdusubsec
EndTestSdutxsw
Seria-lEepromTestCu
SerialEepromTest-Coba
SerialEepromTest-Cosa
BootEepromTestCu
BootEepromTest-Coba
CheckAlarmStatus-Act
DN0933412 Issue 01713
BTSplus mainline commands at the Flexi BSC product family
t
Id:0900d805805b2e3d
CheckAlarmStatus-Fanp
CheckAlarmStatus-Dilna
CheckAlarmStatus-Duvswr
CheckAlarmStatus-Dulna
CheckAlarmStatus-Battery
CheckAlarmStatus-Bcom
CheckAlarmStatu-sTma
CheckAlarmStatus-Dudctma
CheckAlarmStatus-Didctma
CheckAlarmSta-tusAcdcp
CheckAlarmStatus-Fvswrp
CheckAlarmStatus-Ftnfp
CheckAlarmStatus-Lmu
CheckAlarmSta-tusSdulna
CheckAlarmSta-tusSdusec
CheckAlarmSta-tusSdusubsec
CheckAlarmSta-tusSdutxsw
LocalTestLoopCu
SerialEepromTest-Fcumain
ResynctestSyn-cBtse
PreliminaryTest-sSyncBtse
714DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805b2e3d
t
PreliminaryTestsFc-utr
PreliminaryTests-Fcumain
LocalTestLoopFcutr
EndTestSyncBtse
EndTestBcom
EndTestFcutr
EndTestFcuMain
BootEepromTest-Fcumain
PreliminaryTestsDu-amco
CheckAlarmStatus-Duamco
EndTestDuamco
PreliminaryTestsF6dctma
PreliminaryTestsF6lna
PreliminaryTestsF6tnfP
PreliminaryTestsF6vswrP
CheckAlarmStatusF6dctma
CheckAlarmStatusF6lna
CheckAlarmStatusF6tnfP
CheckAlarmStatusF6vswrP
EndTestF6dctma
EndTestF6lna
EndTestF6tnfP
EndTestF6vswrP
EndTestAcdcp
phaseStatus Waiting
Pass
Fail
DN0933412 Issue 01715
BTSplus mainline commands at the Flexi BSC product family
t
Id:0900d805805b2e3d
Default ValueNone.
Contained in the following commands: GET BTSETEST
TESTNOtestNo
This attribute corrisponde to the instance numeber of the test object.
Validity Range
Default ValueNone.
Contained in the following commands: STOPTEST BTSEP
TESTOUTtestOutcome
This attribute informs the operator about the outcome of the current test phase. It is con-tained in the "Test Report" and can be queried by the user during the test via a "GET".
INCONCLUSIVE indicates that no "Pass" or " Fail" outcome has been determinated yet.
PASSED and FAIL are possible for all phases of the test. Further information (e.g. about the number of the failed test phase) is only available in the test report which is sent at the end of the test.
PASSED generally indicates that the test was executed correctly and no problems were found.
FAILED generally indicates that the test was executed correctly and a problem was found.
Validity Range
Default ValueNone.
Contained in the following commands: GET BTSETEST
Running
0 - 255
INCONCLUSIVE
PASSED
FAILED
716DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805b2e3d
t
TESTPWRREDtestPowerReduction
This attribute defines the output power reduction if the transceiver test mode is acti-vated. Its value is adapted to the static power reduction range.
The default value means that the testPowerReduction is not set and as a consequence the test mode can not be enabled.
Validity Range
Default ValueNone.
Contained in the following commands: GET TRX
TESTSTtestState
This attribute defines the current state of the test.
Validity Range
Default ValueNone.
Contained in the following commands: GET BTSETEST
TEXTtext
new information
Validity Range
Default ValueNone.
Contained in the following commands: None.
<ANY>
IDLE
INITIALIZING
TESTING
TERMINATING
1..256 characters string
DN0933412 Issue 01717
BTSplus mainline commands at the Flexi BSC product family
t
Id:0900d805805b2e3d
TIMEDELAYtimeDelay(sec)
This parameter is sent in the 'Activate SW Delayed' command by the Flexi BSC product family. It identifies the number of seconds that the BTSplus mainline waits before acti-vating the specified SW version.
Validity Range
Default ValueNone.
Contained in the following commands: ACTIVATE_DELAYED BTSM
TNCHtNCH(*multiframes)
This attribute describes the minimum repetition period for the Notification/NCH mes-sages. The NCH blocks are a subset of the CCCH blocks reserved for AGCH.
The attribute doesn't denote the minimum repetition period within one CCCH block. Within a CCCH block 1 ... 7 NCH blocks can be used.
(the attribute is indicated in units of multiframes)
Validity Range
Default Value 16
Contained in the following commands: GET BTS TIMER
TNFTARGFtnfTargetFrequency
0 - 254
1 - 254
This attribute defines the target frequency the TNF is to be tuned. It is set internally by the BTSplus mainline after creation, frequency update or deletion of any functional-related TRX instance and is read-only for any external interface of the BTSplus mainline.
In case of "FTNFP" the attribute shows the "actual frequency" of the TNF: this means that the value of the attribute changes during the "tuning" of the TNF or during the "parking" of the TNF.
718DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805b2e3d
t
Validity Range
Default ValueNone.
Contained in the following commands: GET F6TNFP, GET FTNFP
TRXAREAtrxArea
This attribute specifies whether a TRX belongs to a concentric cell and to which area it belongs.
The attribute also indicates whether the concentric cell intracell handover algorithm is enable (value 01 or 02) or disabled (value 00). If it is enabled it will be executed before the conventional inter/intracell handover algorithms.
Validity Range
Default Value NONE - TRX doesn't belong to a concentric cell
Contained in the following commands: GET TRX
cellAllocationNum-ber
Hex Decimal
GSM900 "BB900" 0001 ... 007C 1 ... 124
GSM EXTENDED "F2ONLY900"
0000 ... 007C
03CF ... 03FF
0 ... 124
975 ... 1023
GSM EXTENDED REDUCED "EXT900"
0000
0000 ... 007C
03CF ... 03FF
0000
0 ... 124
975 ... 1023
DCS 1800 "DCS1800"
0200 ... 0375 512 ... 885
PCS 1900 0200 ... 032A 512 ... 810
GSM-R not supported not supported
ANY (only Parking position)
FF00 65280
0 - 65535
<NULL>
NONE
INNER
COMPLETE
DN0933412 Issue 01719
BTSplus mainline commands at the Flexi BSC product family
t
Id:0900d805805b2e3d
TRXCPBLtrxCapability
This attribute reflects the real capabilities of a TRX after harware has been assigned to it. It is set after the TRX allocation by the BTSplus mainline. If the TRX object is created in advance or hardware is not allocated to the TRX the attribute has the value unknown. It is read-only from the Abis/LMT Evolution point of view (GET TRX). The Flexi BSC product family has to perform a GET on this attribute each time the TRX performs a tran-sition to "enabled".
Validity Range
Default Value UNKNOWN
Contained in the following commands: GET TRX
TRXFREQcarrierFrequency
UNKNOWN
GSM
EDGE
This attribute defines the radio frequency allocated and available to a cell.
cellAllocationNum-ber
Decimal
GSM900 "BB900" 1 ... 124
GSM EXTENDED "F2ONLY900"
0 ... 124
975 ... 1023
GSM-R 955 ... 974
GSM EXTENDED REDUCED "EXT900"
0 ... 124
975 ... 1023
DCS 1800 "DCS1800"
512 ... 885
PCS 1900 512 ... 810
GSM-DCS 0 ... 124
975 ... 1023
512 ... 885
GSM850 128 ... 251
720DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805b2e3d
t
Validity Range
Default ValueNone.
Contained in the following commands: GET TRX
TRXMDtrxMode
This attribute defines the mode of a TRX that required from the operator. Depending on it's value the BTSplus mainline tries to allocate an appropriate hardware to the TRX object.
Validity Range
Default Value GSM
Contained in the following commands: GET TRX
TSCtrainingSequenceCode
GSM850-PCS 128 ... 251
512 ... 810
GSM850-DCS 128 ... 251
512 ... 885
0 to 64 items of
0 - 1023
GSM
EDGE
This attribute contains the Training Sequence Code (TSC) of a radio channel. If the TSC value is set NULL, TSC is always equal to the BCC (Base Transceiver Station Colour Code) for both control and traffic channels.
Notes:
1. A NULL (FF) value is possible for both control and traffic channels and signifies that the BCC (BS colour code of attri-bute "bsIdentityCode / BSIC") shall be used as the TSC value for the channel.
DN0933412 Issue 01721
BTSplus mainline commands at the Flexi BSC product family
t
Id:0900d805805b2e3d
Validity Range
Default ValueNone.
Contained in the following commands: GET CHAN
TSLPOOLtslPool
The BportNumber validity range is specified as follows:
00..07 (not only for BS82II)
2. In case of a control channel only the NULL (FF) value can be specified, i.e. only a reference to the BCC is allowed.
TSC_00
TSC_01
TSC_02
TSC_03
TSC_04
TSC_05
TSC_06
TSC_07
TSC_is_BCC_of_BSIC
This attribute defines the pool of Abis timeslots (TSL) on a granularity of 16Kbit/s subslots (SSL) which can be used for traffic within a BTSplus mainline.
The attribute contains an entry of 17 bytes for each used BPort:
- the first byte indicates the number of the BPort (BPortNum-ber),
- the following 16 bytes (BPortBitmap) contain a bitmap - the subslots which can be used for traffic are indicated by setting the corresponding bits in the BPortBitmap bytes to 1. In case of PCM24 the TSL 0 and TSL 25-31 don't exist, therefore the related bits are set to 0.
Out of this pool the Flexi BSC product family assigns dynamically the Abis timeslots to a call. The information about the actual timeslot/sub-slot ("Abis Resources") is sent by the Flexi BSC product family to the BTSplus mainline on the radio signalling link at the begin of each call ("channel Activation") and during the call ("Modify Abis Channel") if a modification is necessary.
722DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805b2e3d
t
00..03 (only for BS82II)
Validity Range
Default ValueNone.
Contained in the following commands: GET BTSM NOSWL
TSYNCtSync(*10ms)
This attribute defines the timer value, that will be used by the BTSplus mainline to super-vise timeout of TRAU frame handling. This timer is used only if a BTSplus mainline-TRAU traffic connection is already established. If the BTSplus mainline detects a loss of frame synchronisation it starts the timer tSync. It is cleared, if a frame is received again. If it expired, a connection failure indication is reported to the Flexi BSC product family.
A change of the attribute becomes effective after the reception of a TRAU frame i.e. in the case after 20 ms and in the worst case after the expiration of the current timer.
(value indicated in milliseconds; step size 10 ms)
Validity Range
Default Value 1000 (corresponding to 10 sec.)
Contained in the following commands: GET BTS TIMER
TSYNCDtSyncD(*10ms)
This attribute defines the timer value, that will be used by the BTSplus mainline to super-vise timeout of downlink TRAU frame handling in case of 14.5kbit/s data connections. If loss of frame synchronization detected by the BTSplus mainline it starts a timer TsyncD and starts sending Data TRAU Frames in the uplink direction to trigger the TRAU to start
1 to 8 items of
BPortNumber BPORT0
BPORT1
...
BPORT7
BPortBitMap 16 to 16 items of
B#0 - B#11111111
10 - 10000
DN0933412 Issue 01723
BTSplus mainline commands at the Flexi BSC product family
t
Id:0900d805805b2e3d
sending Data TRAU Frames in the downlink direction to be used for downlink Synchro-nization Recovery. TsyncD is reset every time frame synchronization is again obtained. If TsyncD expires before frame synchronization is again obtained, a connection failure indication is reported to the Flexi BSC product family.
(value indicated in milliseconds; step size 10 ms)
Validity Range
Default Value 1000 (corresponding to 100 sec.)
Contained in the following commands: GET BTS TIMER
TSYNCRtSyncR(*10ms)
This attribute defines the timer value, that will be used by the BTSplus mainline to super-vise the uplink Synchronization Recovery in case of 14.5kbit/s data connections. When the BTSplus mainline receives an Extended Data TRAU Frame indicating an Uplink Frame Error and which has no errors on the synchronization pattern and the control bits, it starts the timer TsyncR. TsyncR is reset every time three consecutive TRAU frames are received without Uplink Frame Error indication, without errors on the frame synchro-nization pattern and on the control bits. If TsyncR expires before frame synchronization is again obtained, the BTSplus mainline starts sending Data TRAU Frames in the uplink direction to be used for uplink Synchronization Recovery.
(value indicated in milliseconds; step size 10 ms)
Validity Range
Default Value 400 (corresponding to 4 sec.)
Contained in the following commands: GET BTS TIMER
TSYNCUtSyncU(*10ms)
This attribute defines the timer value, that will be used by the BTSplus mainline to super-vise timeout of uplink TRAU frame handling in case of 14.5kbit/s data connections. When the BTSplus mainline receives an Extended Data TRAU Frame indicating an Uplink Frame Error and which has no errors on the synchronization pattern and the control bits, it starts a timer TsyncU. TsyncU is reset every time three consecutive TRAU
10 - 10000
10 - 10000
724DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805b2e3d
t
frames are received without Uplink Frame Error indication, without errors on the frame synchronization pattern and on the control bits. If TsyncU expires before frame synchro-nization is again obtained, a connection failure indication is reported to the Flexi BSC product family.
(value indicated in milliseconds; step size 10 ms)
Validity Range
Default Value 1000 (corresponding to 10 sec.)
Contained in the following commands: GET BTS TIMER
TTRAUtTrau(*10ms)
This attribute defines the timer value, that will be used by the BTSplus mainline to super-vise timeout of TRAU datalink (traffic) at connection establishment or handover. It is set with sending the first TRAU dataframe uplink and cleared, when the first frame downlink arrives. If it is expires, a connection failure indication is reported to the Flexi BSC product family.
(value indicated in milliseconds; step size 10 ms)
Validity Range
Default Value 1000 (corresponding to 10 sec.)
Contained in the following commands: GET BTS TIMER
TUPLREPtimerUplinkReply
The attribute defines the timer for the repetition of the UplinkFree message with "reply on uplink access request".
Validity Range
Default Value 20 seconds
10 - 10000
10 - 10000
5 - 60
DN0933412 Issue 01725
BTSplus mainline commands at the Flexi BSC product family
t
Id:0900d805805b2e3d
Contained in the following commands: GET BTS TIMER
TXBMAXFtxBandMaxFreq(kHz*100)
Attribute data provided by TMA.
Validity Range
Default ValueNone.
Contained in the following commands: GET TMA
TXBMINFtxBandMinFreq(kHz*100)
Attribute data provided by TMA.
Validity Range
Default ValueNone.
Contained in the following commands: GET TMA
TXDIVTSEXCPTtxDivTimeShiftExcept
The TX Diversity Time Shift operation might be disabled for certain type of TX burst, which are timing-sensitive (e.g. SCH channel for location services). In this case the parallel transmission of the slave CU is disabled when the certain burst type is going to be transmitted. The attribute txDivTimeShiftExcept allows to configure time slots or logical channels, which shall be excluded from applying the Tx Diversity Time Shift. The call processing software supervises bursts to be transmitted and disables the slave transmission if the burst should not be transmitted. The attribute is only valid if the feature Tx Diversity Time Shift is enabled (attribute enableTxDivTimeShift). A change of the attribute value causes a traffic interruption on all TRX of the BTS and a restart of the feature Tx Diversity Time Shift.
0 - 65535
<NULL>
0 - 65535
<NULL>
726DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805b2e3d
t
Validity Range
Default Value NONE (diversity applied for all channel)
Contained in the following commands: GET BTS TIMER
TXDIVTSPARtxDivTimeShiftParam
The attribute txDivTimeShiftParam is used to set the time shift between the transmit signals of the master and the slave CU. The time shift is specified on a symbol base in the range between -5 .... +5 symbols in steps of 0,25 symbols. A symbol represents one information unit (e.g. 1 bit) is transmitted within 3,693 s. The attribute is only valid if the feature Tx Diversity Time Shift is enabled (attribute enableTxDivTimeShift). A change of the attribute value causes a traffic interruption on all TRX of the BTS and a restart of the feature Tx Diversity Time Shift.
Validity Range
Default Value -1 symbol, but has to be evaluated during field tests
Contained in the following commands: GET BTS TIMER
TXLEVADJtxLevAdjust(dB)
NONE
SCH
BCCHTRXTS0
BCCHTRX
-5.00 - 5.00
The attribute specifies the value needed to adjust the TXLEV value of the transmit path of the CU/FCUTR. For a FCUTR with an even object instance the related transmit path is TX0, for a FCUTR with an odd object instance the related transmit path is TX1.
The attribute value which will be used to compensate attenuation effects caused by combiner equipment, RF cabling and amplification effects of optionally used booster equipment. The operator has to set a reasonable value according the following formula:
txLevAdjust = Attention Factor of used Combiner + Attention Factor of RF Cable - Amplification Factor of used Booster
DN0933412 Issue 01727
BTSplus mainline commands at the Flexi BSC product family
t
Id:0900d805805b2e3d
Validity Range
Default Value
Contained in the following commands: CREATE CU, CREATE FCUTR, GET CU, GET FCUTR, SET CU, SET FCUTR
TXSIGLEVADJtxSigLevAdjust
The attribute specifies the signal level adjust values which shall be applied to the transmit paths oftransceivers using the same frequency band as the BCCH transceiver.
Validity Range
Default ValueNone.
Contained in the following commands: GET BTS TIMER
TXSIGLEVADJCtxSigLevAdjustCompl
The attribute specifies the signal level adjust values which shall be applied to the transmit paths oftransceivers using the complementary frequency band. The value is only meaningful in case of a multiband cell.
Validity Range
Default ValueNone.
Contained in the following commands: GET BTS TIMER
TYPOFETHtypeOfEthernet
The attribute defines the type of Ethernet framing which is used for transmitted packets.
-63.0 - 63.0
0.0
<ANY>
<ANY>
728DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805b2e3d
t
Validity Range
Default Value
Contained in the following commands: GET COBAETHINTF, SET COBAETHINTF
TYPRACKtypeOfBtse
This attribute identifies the type of BTSplus mainline.
This attribute defines the type of the rack.
For the BTSplus mainline family given by 'hh=04' , it is possible to set the value of typeOfBTSE for rack #0 only once - if the operator wants to change the stored value he has to format the FLASH EPROM first or delete the Flash-DB.
For an rack instance number <> 0 an update of the attribute is blocked by the BTSplus mainline SW. This means if an operator wants to change the attribute value in a rack <> 0 he has to delete the rack first and then recreate it with the new value of typeOfBTSE.
Below are reported more detailed information about the validity range:
BS20 (value only possible for rack #0)
BS21E (value only possible for rack #0)
BS22 (value only possible for rack #0)
BS60 (value only possible for rack #0)
BS61E (value only possible for rack #0)
not_valid (value possible only in LMT Evolution phase 2 as result of a
GET command for rack #0)
Validity RangeIn commands CREATE RACK, SET RACK:
ethernet_II
iEEE802_SNAP
ethernet_II
BS240
BS241
BS240SR
BS241SR
BS40
BS40II
BS41
BS240XL
BS240XLSR
DN0933412 Issue 01729
BTSplus mainline commands at the Flexi BSC product family
t
Id:0900d805805b2e3d
In commands GET RACK:
Default ValueNone.
Contained in the following commands: CREATE RACK, GET RACK, SET RACK
BS82II
BS240
BS241
BS240SR
BS241SR
BS40
BS41
BS240XL
BS240XLSR
BS240XS
BS240SWB
BS241SWB
BS240XLSWB
BS82II
BS40II
not_valid
730DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805b2929
v
v
VENDNAvendorName
This attribute type identifies the vendor of the associated Object. This attribute is defined as an "ASCII String" and is not terminated by a NULL character.
Validity Range
Default ValueNone.
Contained in the following commands: GET BTSEP NOSWL, SET BTSEP
VGSCULFTvoiceGroupUplinkFree(*10ms)
1..37 characters string
If the uplink of the group call is free, and also no talker is in the cell on a dedicated channel, the network provides an UPLINK FREE message on the main signalling channel periodically. The timer vgscULFreeTimer plus an offset of 440ms defines the repetition rate of sending this message; the BTSplus mainline limits the maximum repetition rate on 1440ms.
The BTSplus mainline stops the timer when the uplink is free again, and also no talker is in the cell on a dedicated channel.
Setting this attribute to the lowest possible value means that a talker request by a mobile station can be started with most minimal delay. On the other side, a high repetition rate of UPLINK FREE messages leads to a certain speech frame erasure rate, which may cause an audible degradation of the speech quality on the group downlink channel; although there is no talker in the group call at this state, there may be dispatchers speaking on the group downlink channel.
vgcsULFreeTimer value (decimal)
vgcsULFreeTimer
* 10 ms
UPLINK FREE
repetition rate
1 10 ms 450 ms
2 20 ms 460 ms
3 30 ms 470 ms
: : :
100 100 ms 1440 ms
DN0933412 Issue 01731
BTSplus mainline commands at the Flexi BSC product family
v
Id:0900d805805b2929
Validity Range
Default Value 10 ms
Contained in the following commands: GET BTS TIMER
VLANIDvlanId
This attribute defines optional virtual LAN (VLAN) identifier. The vlanId is used by all pseudo wires (CESPW) of the CESTUNNEL instance.
If vlanId is set to none the VLAN tag in the Ethernet Header will be omitted. The object must be locked before modifying the vlanId via the SET command.
Validity RangeIn commands CREATE CESTUNNEL, SET CESTUNNEL:
In commands GET CESTUNNEL:
Default ValueIn moc(s) CESTUNNEL:
None.
In moc(s) CESTUNNEL:
Contained in the following commands: CREATE CESTUNNEL, GET CESTUNNEL, SET CESTUNNEL
VSWRTDBvswrThresholdDb
This attribute determines the repetition rate for the “upl_busy” message per cell.
Default suggested value: 3 sec. The value sets the TX return loss threshold value of an MFDUAMCO antenna branch. The value is aligned with the combiner if a MFDUAMCO is equipped.
The object is set to degraded if the low threshold is crossed. Crossing the high threshold leads to disabled state.
Default Value: 10 ms
1 - 100
0 - 4094
<NULL>
<ANY>
NULL
732DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805b2929
v
The attribute is meaningless if an old DUAMCO or FDUAMCO is equipped. Neverthe-less the value is stored in the database and used if a MFDUAMCO will be equipped later on.
Validity Range
Default Value
Contained in the following commands: CREATE DUVSWR, CREATE F6VSWRP, GET DUVSWR, GET F6VSWRP, SET DUVSWR, SET F6VSWRP
LOW_2_0_HIGH_3_0
LOW_2_5_HIGH_3_5
LOW_3_0_HIGH_4_0
LOW_2_0_HIGH_3_0
DN0933412 Issue 01733
BTSplus mainline commands at the Flexi BSC product family
w
Id:0900d805805b292b
w
WDDUVSWRwiringDuamcoVswr
This attribute represents the wiring between a DUAMCO_VSWR and several CUs (TX output)/FCUMAINs (TX0 output or TX1 output) which the operator has to perform at installation time.
In case of FCUMAIN with fcuMode=singleCUMode or in case of CU, the DUAMCO_VSWR and the CUs/FCUMAINs are in the same rack and belong to the same cell.
In case of FCUMAIN with fcuMode=douleCUMode, the objects can belong to two differ-ent cells.
Due to the physical properties of the DUAMCO_VSWR, up to 4 CUs/FCUMAINs can be connected."
From SW point of view the FDUAMCO is considered just as an HW variant of the DUAMCO, so an extra term like 'FDUAMCO_DUVSWR' is not introduced.
The BTSplus mainline SW does not check if the entered value is compatible with typeOf-BTSE; e.g. an input of CU7 is not rejected in a BTSplus mainline BS40 although BS40 allows only the creation of CU 0-3.
g All CUs/FCUMAINs which are listed in a GET DUVSWR for WDDUVSWR have to be locked before the cabling of one of these CUs/FCUMAINs can be removed from WDDUVSWR.
g The UIDL construct used is enumList.
Below are reported some detailed information about validity range values:
CU0 ... CU11 (CU4 ... CU7 only for BS240 and BS241)
(CU4 ... CU11 only for BS240XL)
FCUMAIN0TX0
FCUMAIN0TX1
:
FCUMAIN11TX0
FCUMAIN11TX1
(FCUMAIN4TX0 ... FCUMAIN7TX1 only for BS240
and BS241)
:
(FCUMAIN4TX0 ... FCUMAIN11TX1 only for
BS240XL)
Validity Range
1 to 4 items of
CU0
CU1
734DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805b292b
w
Default ValueNone.
CU2
CU3
CU4
CU5
CU6
CU7
CU8
CU9
CU10
CU11
FCUMAIN0TX0
FCUMAIN0TX1
FCUMAIN1TX0
FCUMAIN1TX1
FCUMAIN2TX0
FCUMAIN2TX1
FCUMAIN3TX0
FCUMAIN3TX1
FCUMAIN4TX0
FCUMAIN4TX1
FCUMAIN5TX0
FCUMAIN5TX1
FCUMAIN6TX0
FCUMAIN6TX1
FCUMAIN7TX0
FCUMAIN7TX1
FCUMAIN8TX0
FCUMAIN8TX1
FCUMAIN9TX0
FCUMAIN9TX1
FCUMAIN10TX0
FCUMAIN10TX1
FCUMAIN11TX0
FCUMAIN11TX1
DN0933412 Issue 01735
BTSplus mainline commands at the Flexi BSC product family
w
Id:0900d805805b292b
Contained in the following commands: CREATE DUVSWR, GET DUVSWR, SET DUVSWR
WDFTNFPwiringDataFtnfp
The following values are possible for 'CU_wiring':
CU0 ... CU11 (CU4 ... CU7 only for BS240 and BS241)
(CU4 ... CU11 only for BS240XL)
FCUMAIN0TX0
FCUMAIN0TX1
:
FCUMAIN11TX0
FCUMAIN11TX1
(FCUMAIN4TX0 ... FCUMAIN7TX1 only for BS240
and BS241)
:
(FCUMAIN4TX0 ... FCUMAIN11TX1 only for
BS240XL)
This attribute defines the pool of Abis timeslots (TSL) on a granularity of 16Kbit/s subslots (SSL) which can be used for traffic within a BTSplus mainline.
This attribute represents the wiring:
- between the TX input of a FICOM_TNFP and the TX output of a CU
- between the TX input of a FICOM_TNFP and the TX0 or TX1 output of a FCUMAIN
and furtheron it describes to which FICOM_VSWR the FICOM_TNFP is related to. The wiring has to be done by the operator at installation time.
In case of FCUMAIN with fcuMode=singleCUMode or in case of CU, the FICOM_TNFP, the CU/FCUMAIN and the FICOM_VSWRP are in the same rack and belong to the same cell.
In case of FCUMAIN with fcuMode=douleCUMode, the objects can belong to two different cells.
The BTSplus mainline SW does o't check if the entered value is com-patible with typeOfBTSE; e.g. an input of CU7 isn't rejected in a BS40 although BS40 allows only the creation of CU 0-3.
Note: 'CU_wiring' is used for CU as well as for FCUMAIN, the name 'CU_wiring' has not been changed because it is used in LMT Evolu-tion-GUI/CLI.
736DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805b292b
w
The following values are possible for 'FVSWRP wiring':
FVSWRP0
FVSWRP1
FVSWRP2
FVSWRP3
Validity Range
CUWiring CU0
CU1
CU2
CU3
CU4
CU5
CU6
CU7
CU8
CU9
CU10
CU11
FCUMAIN0TX0
FCUMAIN0TX1
FCUMAIN1TX0
FCUMAIN1TX1
FCUMAIN2TX0
FCUMAIN2TX1
FCUMAIN3TX0
FCUMAIN3TX1
FCUMAIN4TX0
FCUMAIN4TX1
FCUMAIN5TX0
FCUMAIN5TX1
FCUMAIN6TX0
FCUMAIN6TX1
FCUMAIN7TX0
FCUMAIN7TX1
FCUMAIN8TX0
FCUMAIN8TX1
DN0933412 Issue 01737
BTSplus mainline commands at the Flexi BSC product family
w
Id:0900d805805b292b
Default ValueNone.
Contained in the following commands: CREATE F6TNFP, CREATE FTNFP, GET F6TNFP, GET FTNFP
WDLNAwiringDataLna
This attribute represents the wiring between a DUAMCO_LNA or a DIAMCO_LNA and several CUs/FCUMAINs the operator has to perform at installation time and that is not foreseen to be fixed by the configuration rules.
In case of FCUMAIN with fcuMode=singleCUMode or in case of CU, the DUAMCO/DIAMCO_LNA and the CUs/FCUMAINs are in the same rack and belong to the same cell.
In case of FCUMAIN with fcuMode=douleCUMode, the objects can belong to two differ-ent cells.
When a second cell number is indicated (see attribute secondCellNumber), also in case of CU the objects can belong to two different cells.
Due to the physical properties of the DUAMCO_VSWR, up to 8 different Us/FCUMAINs can be connected. Each CU has a 'normal path' RX input and a 'diversity path' RX input and the operator must indicate which of them is wired to the DUAMCO/DIAMCO_LNA. The FCUMAIN supports the 'normal path' RX input, the diversity path RX input and two further Rx inputs: Rx C / N1 and Rx D / D1.
The BTSplus mainline SW does not check if the entered value is compatible with typeOf-BTSE; e.g. an input of CU7N / CU7D isn't rejected in a BS40 although BS40 allows only the creation of CU 0-3.
Validity Range (object DILNA/DULNA) are possible for 'RX_wiring n':
CU0N (CU0 normal path)
CU0D (CU0 diversity path)
:
CU11N (CU11 normal path)
FCUMAIN9TX0
FCUMAIN9TX1
FCUMAIN10TX0
FCUMAIN10TX1
FCUMAIN11TX0
FCUMAIN11TX1
FVSWRPWiring FVSWRP0
FVSWRP1
...
FVSWRP3
738DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805b292b
w
CU11D (CU11 diversity path)
FCUMAIN0N (FCUMAIN0 normal path)
FCUMAIN0D (FCUMAIN0 diversity path)
FCUMAIN0N1 (FCUMAIN0 Rx C / N1 path)
FCUMAIN0D1 (FCUMAIN0 Rx D / D1 path)
:
FCUMAIN11N (FCUMAIN11 normal path)
FCUMAIN011D (FCUMAIN11 diversity path)
FCUMAIN11N1 (FCUMAIN11 Rx C / N1 path)
FCUMAIN11D1 (FCUMAIN011 Rx D / D1 path)
(CU4 ... CU7 only for BS240 and BS241)
(CU4 ... CU11 only for BS240XL)
(FCUMAIN4N ... FCUMAIN7D1 only for BS240 and BS241)
(FCUMAIN4N ... FCUMAIN11D1 only for BS240XL)
Validity Range
1 to 8 items of
CU0N
CU0D
CU1N
CU1D
CU2N
CU2D
CU3N
CU3D
CU4N
CU4D
CU5N
CU5D
CU6N
CU6D
CU7N
CU7D
CU8N
CU8D
CU9N
CU9D
CU10N
DN0933412 Issue 01739
BTSplus mainline commands at the Flexi BSC product family
w
Id:0900d805805b292b
CU10D
CU11N
CU11D
FCUMAIN0N
FCUMAIN0D
FCUMAIN0N1
FCUMAIN0D1
FCUMAIN1N
FCUMAIN1D
FCUMAIN1N1
FCUMAIN1D1
FCUMAIN2N
FCUMAIN2D
FCUMAIN2N1
FCUMAIN2D1
FCUMAIN3N
FCUMAIN3D
FCUMAIN3N1
FCUMAIN3D1
FCUMAIN4N
FCUMAIN4D
FCUMAIN4N1
FCUMAIN4D1
FCUMAIN5N
FCUMAIN5D
FCUMAIN5N1
FCUMAIN5D1
FCUMAIN6N
FCUMAIN6D
FCUMAIN6N1
FCUMAIN6D1
FCUMAIN7N
FCUMAIN7D
FCUMAIN7N1
FCUMAIN7D1
FCUMAIN8N
740DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805b292b
w
Default ValueNone.
Contained in the following commands: CREATE DILNA, CREATE DULNA, CREATE F6LNA, GET DILNA, GET DULNA, GET F6LNA, SET DILNA, SET DULNA, SET F6LNA
FCUMAIN8D
FCUMAIN8N1
FCUMAIN8D1
FCUMAIN9N
FCUMAIN9D
FCUMAIN9N1
FCUMAIN9D1
FCUMAIN10N
FCUMAIN10D
FCUMAIN10N1
FCUMAIN10D1
FCUMAIN11N
FCUMAIN11D
FCUMAIN11N1
FCUMAIN11D1
DN0933412 Issue 01741
BTSplus mainline commands at the Flexi BSC product family
Nack causes
Id:0900d805805bfdaa
4 Nack causesString table for ABIS nack causes used by the LMT Evolution
H'1, Incorrect message structure
H'2, Invalid message type value
H'3, <reserved>
H'4, <reserved>
H'5, Invalid object class value
H'6, Object class not supported
H'7, BTS no. unknown
H'8, Transceiver no. unknown
H'9, Object instance unknown
H'A, <reserved>
H'B, <reserved>
H'C, Invalid attribute identifier value
H'D, Attribute identifier not supported
H'E, Parameter value outside permitted range
H'F, Inconsistency in attribute list
H'10, Specified implementation not supported
H'11, Message cannot be performed
H'12, Busy
H'13, <reserved>
H'14, <reserved>
H'15, <reserved>
H'16, <reserved>
H'17, <reserved>
H'18, <reserved>
H'19, Resource not implemented
H'1A, Resource not available
H'1B, Frequency not available
H'1C, Test not supported
H'1D, Capacity restrictions
H'1E, Physical configuration cannot be performed
H'1F, Test not initiated
H'20, Physical configuration cannot be restored
H'21, No such test
H'22, Test cannot be stopped
742DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805bfdaa
Nack causes
H'23, Message inconsistent with physical config.
H'24, File already received
H'25, Complete file not received
H'26, File not available at destination
H'27, File cannot be activated
H'28, Request not granted
H'29, Wait
H'2A, <reserved>
H'7F, <reserved>
H'80, BTSE not able to begin DB Transmission
H'81, DB Transmission failed
H'82, Conflicting channel assignment
H'83, Specified connection does not exist
H'84, Specified Test is not running
H'85, swLoad-header not stored
H'86, swLoad-header mismatch with swImage or VAM file id
H'87, Files listed in swLoad header not stored
H'88, Request already in progress
H'89, Load has not been activated before
H'8A, Starting Time already in use
H'8B, Configuration of specified object not allowed during alignment
H'8C, Update of specified object not allowed in LMT Evolution phase 3
H’8D, Configuration of specified object not allowed during FW download
H'90, invalid file name
H'91, invalid file type
H'92, file not found
H'93, file in use
H'94, file present
H'95, file corrupted
H'96, file test failed
H'97, MO or MOT not locked
H'98, VAM check failed
H'99, VAM file not stored in Flash Eprom
H'9A, Scanner is suspended
H'9B, TEI already in use
H'9C, Update not allowed from Abis interface
DN0933412 Issue 01743
BTSplus mainline commands at the Flexi BSC product family
Nack causes
Id:0900d805805bfdaa
String table for LMT Evolution nack causes used by BTSE
H'9D, Update not allowed from T interface
H'9E, Update not allowed
H'9F, MO already created
H'A0, requested information exceeds maximal message length
H'A1, sw load not compatible with typeOfBTSE
H'A2, Creation out of sequence
H'A3, Invalid attribute value
H'A4, Conflicting timeslot assignment
H'A5, Deletion not possible in Phase3
H'A6, Deletion out of sequence
H'A7, Related BPort instance not created
H'A8, Configuration of remapped timeslots not possible in Phase3
H'A9, feature not released
H'AA, typeOfBTSE has to be set first
H'AB, typeOfBTSE not compatible with typeOfBTSE in other rack(s)
H'AC, max number of object instances is already created
H'AD, no redundant core board available
H’AE, TRX/LPDM related LADPLE doesn’t exist or isn’t consistent
H’AF, Requested data not available
H’B0, Conflicting feature activation
H’B1, Re-synchronization not possible
H’B2, Inconsistency in wiring configuration
H’B3, No FPGA on board
H’B4-F3, Not used
H'F4, Change password failed: syntax error
H'F5, Change password failed: new pwd is the same as old pwd
H’F6-F7, Not used
H'F8, Mandatory security attribute missing
H'F9, Security transmission failed
H'FA, Security transmission missing
H'FB-FE, Not used
H'FF, NULL
H'01, Incorrect message structure
H'02, Invalid message type value
H'03, <reserved>
744DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d805805bfdaa
Nack causes
H'04, <reserved>
H'05, Invalid object class value
H'06, Object class not supported
H'07, BTS no. unknown
H’08, Transceiver no. unknown
H’09, Object instance unknown
H’0A, <reserved>
H’0B, <reserved>
H'0C, Invalid attribute identifier value
H’0D, Attribute identifier not supported
H’0E, Parameter value outside permitted range
H’0F, Inconsistency in attribute list
H’10, Specified implementation not supported
H'11, Message cannot be performed
H'12, System busy
H’13, <reserved>
H’14, <reserved>
H’15, <reserved>
H’16, <reserved>
H’17, <reserved>
H’18, <reserved>
DN0933412 Issue 01745
BTSplus mainline commands at the Flexi BSC product family
Appendix: values for ERFACCHALPDMF, ERFACCH-CMDF, ERSACCHDL, ERSACCHUL and ETOP
Id:0900d8058053dfb7
5 Appendix: values for ERFACCHALPDMF, ERFACCHCMDF, ERSACCHDL, ERSAC-CHUL and ETOP
Assigned Values
Binary Dec Hex
TCH_WFS TCH_HS TCH_FS TCH_EFS TCH_AHS TCH_AFS
0 0 0 0 0 0 0 0 00 0x00
0 0 0 0 0 0 0 1 01 0x01
0 0 0 0 0 0 1 0 02 0x02
0 0 0 0 0 0 1 1 03 0x03
0 0 0 0 0 1 0 0 04 0x04
0 0 0 0 0 1 0 1 05 0x05
0 0 0 0 0 1 1 0 06 0x06
0 0 0 0 0 1 1 1 07 0x07
0 0 0 0 1 0 0 0 08 0x08
0 0 0 0 1 0 0 1 09 0x09
0 0 0 0 1 0 1 0 10 0x0A
0 0 0 0 1 0 1 1 11 0x0B
0 0 0 0 1 1 0 0 12 0x0C
0 0 0 0 1 1 0 1 13 0x0D
0 0 0 0 1 1 1 0 14 0x0E
0 0 0 0 1 1 1 1 15 0x0F
0 0 0 1 0 0 0 0 16 0x10
0 0 0 1 0 0 0 1 17 0x11
0 0 0 1 0 0 1 0 18 0x12
0 0 0 1 0 0 1 1 19 0x13
0 0 0 1 0 1 0 0 20 0x14
0 0 0 1 0 1 0 1 21 0x15
0 0 0 1 0 1 1 0 22 0x16
0 0 0 1 0 1 1 1 23 0x17
0 0 0 1 1 0 0 0 24 0x18
0 0 0 1 1 0 0 1 25 0x19
0 0 0 1 1 0 1 0 26 0x1A
0 0 0 1 1 0 1 1 27 0x1B
0 0 0 1 1 1 0 0 28 0x1C
746DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d8058053dfb7
Appendix: values for ERFACCHALPDMF, ERFACCH-CMDF, ERSACCHDL, ERSACCHUL and ETOP
g ERFACCHALPDMF:
0 0 0 1 1 1 0 1 29 0x1D
0 0 0 1 1 1 1 0 30 0x1E
0 0 0 1 1 1 1 1 31 0x1F
0 0 1 0 0 0 0 0 32 0x20
0 0 1 0 0 0 0 1 33 0x21
0 0 1 0 0 0 1 0 34 0x22
0 0 1 0 0 0 1 1 35 0x23
0 0 1 0 0 1 0 0 36 0x24
0 0 1 0 0 1 0 1 37 0x25
0 0 1 0 0 1 1 0 38 0x26
0 0 1 0 0 1 1 1 39 0x27
0 0 1 0 1 0 0 0 40 0x28
0 0 1 0 1 0 0 1 41 0x29
0 0 1 0 1 0 1 0 42 0x2A
0 0 1 0 1 0 1 1 43 0x2B
0 0 1 0 1 1 0 0 44 0x2C
0 0 1 0 1 1 0 1 45 0x2D
0 0 1 0 1 1 1 0 46 0x2E
0 0 1 0 1 1 1 1 47 0x2F
0 0 1 1 0 0 0 0 48 0x30
0 0 1 1 0 0 0 1 49 0x31
0 0 1 1 0 0 1 0 50 0x32
0 0 1 1 0 0 1 1 51 0x33
0 0 1 1 0 1 0 0 52 0x34
0 0 1 1 0 1 0 1 53 0x35
0 0 1 1 0 1 1 0 54 0x36
0 0 1 1 0 1 1 1 55 0x37
0 0 1 1 1 0 0 0 56 0x38
0 0 1 1 1 0 0 1 57 0x39
0 0 1 1 1 0 1 0 58 0x3A
0 0 1 1 1 0 1 1 59 0x3B
0 0 1 1 1 1 0 0 60 0x3C
0 0 1 1 1 1 0 1 61 0x3D
0 0 1 1 1 1 1 0 62 0x3E
0 0 1 1 1 1 1 1 63 0x3F
DN0933412 Issue 01747
BTSplus mainline commands at the Flexi BSC product family
Appendix: values for ERFACCHALPDMF, ERFACCH-CMDF, ERSACCHDL, ERSACCHUL and ETOP
Id:0900d8058053dfb7
For the binary representation 0 means that R-FACCH for any LAPDm command or response frames is not applied for specified speech codec type and 1 means that R-FACCH for any LAPDm 5 command or response frames is applied for specified speech codec type.Value 0x00 has specific meaning and should be read as R-FACCH for any LAPDm command or response frames is not applied for any speech codec type. All other values are reserved for the future use.
ERFACCHCMDF: For the binary representation 0 means that R-FACCH on LAPDm command frames is not applied for specified speech codec type and 1means that R-FACCH on LAPDm command frames is applied for apecified speech codec type.
Value 0x00 has specific meaning and should be read as R-FACCH on LAPDm command frames is not applied for any speech codec type. All other values are reserved for the future use.
ETOP:
For the binary representation 0 means that TOP is not applied for specified speech codec type and 1 means that TOP is applied for specified speech codec type.Value 0x00 has specific meaning and should be read as TOP is not applied for any speech codec type. All other values are reserved for the future use.
748DN0933412 Issue 01
BTSplus mainline commands at the Flexi BSC productfamily
Id:0900d8058057b3aa
Appendix B: commands available only in remote mode
6 Appendix B: commands available only in remote mode
6.1 REQCURSTASYN BTSEP
Command Tree:“MANAGED-ELEMENT -> BSS-EQUIPMENT -> BTSEP -> REQCURSTASYN BTSEP”
Applicability:Phase 3.
Visibility level: 0.
Command Description:new information
Long Names:NAME Address of the managed object
ALGNSTEP alignmentStep
System Responses:Operation Completed
None.
Operation Failed
None.
Application Guidelines:None.
Example of Command Execution:None.
6.2 GET ENVABTSESUM
Command Tree:“MANAGED-ELEMENT h BSS-EQUIPMENT h BTSEEM h RACK h ENVABTSESUM h GET ENVABTSESUM”
Applicability:Phase 3.
Visibility level: 0.
REQCURSTASYN BTSEEP
NAME=BTSEP:0..0 [ALGNSTEP=];
GET ENVABTSESUM NAME=BTSEEM:0..0/RACK:0..1/ENVABTSESUM:0..0 [,REQATTL=ALS, AST, AVS, OST];
DN0933412 Issue 01749
BTSplus mainline commands at the Flexi BSC product family
Appendix B: commands available only in remote mode
Id:0900d8058057b3aa
Command Description:new information
Long Names:NAME Address of the managed object
REQATTL Required attribute list
ALS alarmStatus
AST administrativeState
AVS availabilityStatus
OST operationalState
System Responses:Operation Completed
None.
Operation Failed
None.
Application Guidelines:None.
Example of Command Execution:None.