Bridge Bearings. Use of BS 5400: Part 9: 1983 · National Roads Authority Volume 2 Section 3 Design Manual for Roads and Bridges Part 1 BD 20/92 Addendum December 2000 1 NRA ADDENDUM

Bridge Bearings. Use of BS 5400: Part 9: 1983

DN-STR-03004 December 2000

Design Standards DN

TRANSPORT INFRASTRUCTURE IRELAND (TII) PUBLICATIONS

About TII Transport Infrastructure Ireland (TII) is responsible for managing and improving the country’s national road and light rail networks. About TII Publications TII maintains an online suite of technical publications, which is managed through the TII Publications website. The contents of TII Publications is clearly split into ‘Standards’ and ‘Technical’ documentation. All documentation for implementation on TII schemes is collectively referred to as TII Publications (Standards), and all other documentation within the system is collectively referred to as TII Publications (Technical). This system replaces the NRA Design Manual for Roads and Bridges (NRA DMRB) and the NRA Manual of Contract Documents for Road Works (NRA MCDRW). Document Attributes Each document within TII Publications has a range of attributes associated with it, which allows for efficient access and retrieval of the document from the website. These attributes are also contained on the inside cover of each current document, for reference. For migration of documents from the NRA and RPA to the new system, each current document was assigned with new outer front and rear covers. Apart from the covers, and inside cover pages, the documents contain the same information as previously within the NRA or RPA systems, including historical references such as those contained within NRA DMRB and NRA MCDRW. Document Attributes

TII Publication Title Bridge Bearings. Use of BS 5400: Part 9: 1983 TII Publication Number

DN-STR-03004

Activity Design (DN) Document Set Standards

Stream Structures (STR) Publication Date December 2000

Document Number

03004 Historical Reference

BD 20

NRA DMRB and MCDRW References For all documents that existed within the NRA DMRB or the NRA MCDRW prior to the launch of TII Publications, the NRA document reference used previously is listed above under ‘historical reference’. The TII Publication Number also shown above now supersedes this historical reference. All historical references within this document are deemed to be replaced by the TII Publication Number. For the equivalent TII Publication Number for all other historical references contained within this document, please refer to the TII Publications website.

National Roads Authority Volume 2 Section 3 Design Manual for Roads and Bridges Part 1 BD 20/92 Addendum

December 2000 1

NRA ADDENDUM TO

BD 20/92

BRIDGE BEARINGS USE OF BS 5400: PART 9: 1983

Standard BD 20/92 - Bridge Bearings, Use of BS 5400: Part 9: 1983 - is applicable in Ireland with the

following amendments:

GENERAL

1. The Standard provides specification requirements for use in public purchasing contracts. It does not

lay down legislation requirements for products and materials used in road construction in Ireland.

2. At several locations:

For: “Specification for Highway Works (December 1991) (MCHW 1)”

Read: “NRA Specification for Road Works”;

For: “highway”

Read: “road”;

For: “Overseeing Department”

Read: “National Roads Authority”.

http://www.standardsforhighways.co.uk/dmrb/vol2/section3.htm

National Roads Authority Volume 2 Section 3 Design Manual for Roads and Bridges Part 1 BD 20/92 Addendum

December 2000 2

SPECIFIC

1. Page 1/1, Paragraph 1.3:

Delete text and replace with:

“1.3 This Standard should be used forthwith for

all schemes for the construction and/or

improvement of national roads. The Standard

should be applied to the design of schemes already

being prepared unless, in the opinion of the

National Roads Authority, application would result

in significant additional expense or delay progress.

In such cases, Design Organisations should

confirm the application of this Standard to

particular schemes with the National Roads

Authority.”

2. Page 3/1, Paragraph 3.1, line 4:

For: “Notes for Guidance on Specification for Highway Works (December 1991)(MCHW 2).”

Read: “NRA Notes for Guidance on the Specification for Road Works.”

3. Page 4/1, Paragraph 4.2:

Delete Paragraph 4.2 and replace with:

“4.2 NRA Manual of Contract Documents for Road Works:

Volume 1: Specification for Road Works

Volume 2: Notes for Guidance on the Specification for Road Works”.

4. Page 5/1, Section 5:

Delete text and replace with:

“5.1 All technical enquiries or comments on this Standard should be sent in writing to:

Head of Project Management and Engineering

National Roads Authority

St Martin’s House

Waterloo Road

Dublin 4”

……………………………………………

E O’CONNOR

Head of Project Management and

Engineering

Bridge Bearings

Use of BS 5400: Part 9:1983

Summary: This Standard gives the requirements for the design of bridge bearings usingBS 5400: Part 9: 1983

THE HIGHWAYS AGENCY BD 20/92

THE SCOTTISH OFFICE DEVELOPMENT DEPARTMENT

THE WELSH OFFICEY SWYDDFA GYMREIG

THE DEPARTMENT OF THE ENVIRONMENTFOR NORTHERN IRELAND

Volume 2 Section 3Part 1 BD 20/92 Registration of Amendments

ELECTRONIC COPY - NOT FOR USE OUTSIDE THE AGENCY

October 1992 PAPER COPIES OF THIS ELECTRONIC DOCUMENT ARE UNCONTROLLED

REGISTRATION OF AMENDMENTS

Amend Page No Signature & Date of Amend Page No Signature & Date ofNo incorporation of No incorporation of

amendments amendments

Volume 2 Section 3Registration of Amendments Part 1 BD 20/92


PAPER COPIES OF THIS ELECTRONIC DOCUMENT ARE UNCONTROLLED October 1992

REGISTRATION OF AMENDMENTS

Amend Page No Signature & Date of Amend Page No Signature & Date ofNo incorporation of No incorporation of

amendments amendments

DESIGN MANUAL FOR ROADS AND BRIDGES


October 1992 PAPER COPIES OF THIS ELECTRONIC DOCUMENT ARE UNCONTROLLED

VOLUME 2 HIGHWAYSTRUCTURES:DESIGN(SUBSTRUCTURESAND SPECIALSTRUCTURES),MATERIALS

SECTION 3 MATERIALS ANDCOMPONENTS

PART 1

BD 20/92

BRIDGE BEARINGS USE OF BS 5400:PART 9: 1983

Contents

Chapter

1. Introduction

2. Use of the British Standard

3. Additional Requirements

4. References

5. Enquiries

Annex A Amendments to BS 5400: Section 9.1:1983

Volume 2 Section 3 Chapter 1Part 1 BD 20/92 Introduction


October 1992 PAPER COPIES OF THIS ELECTRONIC DOCUMENT ARE UNCONTROLLED 1/1

1. INTRODUCTION

1.1 This Standard updates and replaces BD 20/83:Bridge Bearings - Use of BS 5400: Part 9: 1983. Themajor changes in this revision are as follows:-

i. All references relating to the specificationclauses in BS 5400: Part 9: Section 9.2: 1983,are withdrawn. Specification clauses given inthe Specification for Highway Works(December 1991) (MCHW 1) shall be used.

ii. In clause 10.6 of BS 5400: Section 9.1: 1983the equation for ," is modified.

Scope

1.2 This standard covers the use of BS 5400: Part9: Section 9.1: 1983 for the design of bearings inhighway bridges.

Implementation

1.3 This Standard should be used forthwith on allschemes for the construction, improvement andmaintenance of trunk roads, including motorways,currently being prepared provided that, in the opinion ofthe Overseeing Department, this would not result insignificant additional expense or delay progress. Design Organisations should confirm its application toparticular schemes with the Overseeing Department.

Volume 2 Section 3 Chapter 2Part 1 BD 20/92 Use of the British Standard



2. USE OF THE BRITISH STANDARD

2.1 The design of bearings for the OverseeingDepartment's highway bridges shall be carried out inaccordance with BS 5400: Section 9.1 as amended bythis Standard. The amendments to Section 9.1 are givenin Appendix A to this standard.

2.2 The British Standard BS 5400: Section 9.1 asamended by this Standard supersedes the following:

i. Technical Memorandum (Bridges) No BE1/76; Design Requirements for ElastomericBridge Bearings.

ii. Interim Memorandum (Bridges) No IM 11;PTFE in Bridge Bearings.

2.3 Where reference is made to any Part of BS5400, this shall be taken as a reference to that Part asimplemented by the Overseeing Department.

Volume 2 Section 3 Chapter 3Part 1 BD 20/92 Additional Requirements



3. ADDITIONAL REQUIREMENTS

3.1 Specification clauses for bearings for use in theOverseeing Department's highway bridges are given inthe Specification for Highway Works (December 1991)(MCHW 1). Advice on these is contained in the Notesfor Guidance on the Specification for Highway Works(December 1991)(MCHW 2).

3.2 The clauses in BS 5400: Section 9.1 areexpressed in the form of recommendation generallyusing the word "should"; however these shall beconsidered as mandatory for the purpose of thisStandard.

3.3 Proprietary bearings, and structuralcomponents of bearings (eg in aluminium alloy), whichfall outside the scope of BS 5400: Part 9, are notcovered by this Standard.

3.4 Where bridge bearings are procured through acontract incorporating the Specification for HighwayWorks (December 1991) (MCHW 1) productsconforming to equivalent standards or specifications ofother member states of the European Community willbe acceptable in accordance with the terms of the 104and 105 Series of Clauses of that Specification. Anycontract not containing these Clauses must contain asuitable clause of mutual recognition having the sameeffect regarding which advice should be sought.

Volume 2 Section 3 Chapter 4Part 1 BD 20/92 References



4. REFERENCES

4.1 BS 5400: Steel, Concrete and CompositeBridges Part 9: Bridge bearings. Section 9.1:1983, Code of Practice for design of bridgebearings.

4.2 Manual of Contract Documents for HighwayWorks:-

Volume 1: Specification for Highway Works(December 1991): HMSO (MCHW 1).

Volume 2: Notes for Guidance on theSpecification for Highway Works(December 1991): HMSO (MCHW 2).

Volume 2 Section 3 Chapter 5Part 1 BD 20/92 Enquiries



5. ENQUIRIES

All technical enquiries or comments on this Standard should be sent in writing as appropriate to:-

Chief Highway Engineer The Department of Transport St Christopher House Southwark Street T A ROCHESTER London SE1 OTE Chief Highway Engineer

The Deputy Chief Engineer Roads Directorate The Scottish Office Industry Department New St. Andrew's House J INNES Edinburgh EH1 3TG Deputy Chief Engineer

The Director of Highways Welsh Office Y Swyddfa Gymreig Government Buildings Ty Glas Road Llanishen K J THOMAS Cardiff CF4 5PL Director of Highways

Chief Engineer Dept. of the Environment for Northern Ireland Commonwealth House Castle Street W J McCOUBREY Belfast BT1 1GU Chief Engineer - Roads Service

Orders for further copies should be addressed to:-

DOE/DOT Publications Sales Unit Government Building Block 3, Spur 2 Lime Grove Eastcote HA4 8SE Telephone No: 081 - 429 5170

Volume 2 Section 3Part 1 BD 20/92 Annex A


October 1992 PAPER COPIES OF THIS ELECTRONIC DOCUMENT ARE UNCONTROLLED A/1

AMENDMENTS TO BS 5400: SECTION 9.1: 1983

Page 4

5.6 Add the following at the end of clause:-

"For bearings in halving joints access for inspection and replacement is practically impossible for slab typebridges and extremely difficult for beam and slab construction."

Page 7

5.17 Delete clause and insert the following

"Bearing Schedule. The bearing design requirements and acceptance tests shall be listed in a bearing schedule. A typical bearing schedule for this purpose is set out in Appendix A of Section 9.1."

Page 10

10.1.1 After the last sentence, insert additional sentence as follows:-

"The use of pad and strip bearings shall be restricted to small and simply supported structures of spans less than10 metres."

Page 11

10.6 Delete the equation for ," and insert the following:

" ," = (b "b + l "l) te e i2 2

))))))))))))))) 2 G(t )i

3

The outer protective layers shall be ignored in the calculation of ,"." Page 12

10.6 Delete definition for Gt .i

10.11 Delete `Numerically, H < 0.1 (V+ 2A )'; and insert1

"H is less than each of the following:-

i. 0.1 (V + 2A )1

ii. 0.2V"

Volume 2 Section 3Annex A Part 1 BD 20/92


PAPER COPIES OF THIS ELECTRONIC DOCUMENT ARE UNCONTROLLED October 1992A/2

Page 15

Table 9 Extend the typical bridge bearing schedule by adding the following items and additional footnote at thebottom:-

Number ofcompletebearings to besubjected toacceptancetesting

Bearings other horizontal load** testthan elastomeric at serviceability limitbearings state

Combined vertical and

Combined vertical andhorizontal load** testat ultimate limit state

Laminated Quick production testelastomericbearings

Compressive stiffnesstest

Shear stiffness test

** Load values for testing shall be derived from the design load effects above multiplied by the appropriatevalue of partial material factor ( .m

Ionad Ghnó Gheata na

Páirce,

Stráid Gheata na Páirce, Baile Átha Cliath 8, Éire

www.tii.ie

+353 (01) 646 3600

Parkgate Business Centre,

Parkgate Street,

Dublin 8, Ireland

[email protected]

+353 (01) 646 3601