Boiler System Functional Test

8/13/2019 Boiler System Functional Test

1/8

Boiler SystemFunctional Test FT___

Functional Test

Project ____________________________________

FT- BOILER SYSTEM

HW Boilers B-1 & 2 (condensin! and B-"# $% # Includin 'ssociatedri)ar* HW u)+s 1# 2# "# $% and Secondar* u)+s ,# % .

and T/eir 0ariale S+eed ri3es

14 artici+antsParty Participation

Party filling out this form and witnessing testing ______________________________Dates of tests ______________________Dates of tests ______________________Dates of tests ______________________

24 Test rere5uisitesa. __ The following have been started up and startup reports and prefunctional checklists submitted and

approved ready for functional testing:

__ Boilers __ Heating water piping and valves

__ Heating water pumps __ Variable speed drives

b. __ All control system functions for this and all interlocking systems are programmed and operable per

contract documents including final setpoints and schedules and with debugging loop tuning and sensor anddevice calibrations completed. _________________________________ _________________________

!ontrols !ontractor "ignature or Verbal #ate

c. __ $iping system flushing complete and re%uired report approved.

d. __ &ater treatment system complete and operational.

e. __ Vibration control report approved 'if re%uired(.

f. __ Test and balance 'TAB( complete and approved for the hydronic system.

g. __ All A)* punchlist items for this e%uipment corrected.

h. __ These functional test procedures reviewed and approved by installing contractor.

i. __ "afeties and operating ranges reviewed.

+. __ Test re%uirements and se%uences of operation attached.

k. __ "chedules and setpoints attached.

l. __ "ufficient clearance around e%uipment for servicing.

Notes:

File: ,---/01, !"!" Commissioning Guide Specification --PECI Page1of 0


2/8


m. __ Have all energy savings control strategies setpoints and schedules been incorporated that this boiler and

control system are capable of2 3f not list recommendations below.

n. __ BAS Program Review. 4eview the BA" software control program's( for this e%uipment. $arameters

setpoints and logic se%uences appear to follow the specified written se%uences.

o. __ Packaged Control Program Review. 4eview the packaged control program's( for this e%uipment.$arameters setpoints and logic se%uences appear to follow the specified written se%uences.

p. __ 4ecord made of All Values for !urrent "etpoints '"$t( !ontrol $arameters 5imits #elays 5ockouts

"chedules *tc. !hanged to Accomodate Testing:

ara)eterre-Test

0alues

Returned to re-Test

0alues

Space Temp# Setpts

Time delay $etween stages

Setpoint range for condensing $oilers: %&F'(&F

Differential pressure setpoint: Basement:Penthouse:

Supply temp# reset schedule: )S*T +ST %-F(&F .-F"&F

/hanges for False 0oading:

"4 Sensor 6aliration 6/ec7s4 !heck the sensors listed below for calibration and ade%uate location. This is asampling check of calibrations done during prefunctional checklisting.

Notes:

File: ,---/01, !"!" Commissioning Guide Specification --PECI Page2of 0


3/8


63n calibration7 means making a reading with a calibrated test instrument within 1 inches of the site sensor. Verify that the sensor

reading 'via the permanent thermostat gage or building automation system 'BA"(( compared to the test instrument8measured valueis within the tolerances specified in the prefunctional checklist re%uirements '__________________________(. 3f not install offset

in BA" calibrate or replace sensor. 9se the same test instruments as used for the original calibration if possible.

Sensor 1 0ocation 0ocation)2

1st 3age orB*S4alu

e

5nstrument6easured

4alue

Final 3age orB*S

4alue

Pass7!N8

"AT

H&"T 'bldg loop(

H&4T 'bldg loop(

H&B8, ; < B8, B8< B8, B8< B8, B8

Documents

Boiler System Functional Test