© Copyright Baxters Pty Ltd 2018. All information is found to be correct at time of printing roadvision.com.au // Page 87

AUXILIARYLIGHTINGSPARES// 87 - 92 SPARES

AU

XIL

IAR

Y S

PA

RE

& A

CC

ES

SO

RIE

S

© Copyright Baxters Pty Ltd 2018. All information is found to be correct at time of printingPage 88 // roadvision.com.au

Universal Mounting & Wiring Accessories

AU

XIL

IAR

Y S

PA

RE

& A

CC

ES

SO

RIE

S

RBC HEAVY DUTY BULL BAR CLAMP BRACKETS

Roadvision’s range of RBC heavy duty bull bar clamp brackets provide professional mounting solutions for installing bar and driving lamps on bull bars. With tube

mount kits available for 49mm-81mm diameter tube, they provide a sturdy yet quick and easy mounting solution for our complete range of forward lighting products.

� RBC heavy duty bull bar clamp brackets suitable for installation of light bars or aerials

� Fits from 49mm to 81mm tube diameters (1.93” to 3.19”)

� 8mm x 25mm mounting hole slot

� Heavy duty powder coated die-cast aluminium construction

� Internal protective rubber gasket

� Stainless steel hardware

� Simple DIY design

� Available in black or silver

� Sold as a pair (2 clamps)

RBC HEAVY DUTY BULL BAR CLAMP BRACKETS

BBL-CLMP-M6Universal Bull Bar Clamp Bracket

1.5”-2.5” Tube Aluminium Alloy M6 Mounting Hole (Each)

BBL-CLMP-M8Universal Bull Bar Clamp Bracket

1.5”-2.5” Tube Aluminium Alloy M8 Mounting Hole (Each)

BBL-CLMP-3BUniversal Bull Bar X Clamp Bracket 3” Tube Cast Iron 15mm Mounting

Hole (Pair)

TUBE MOUNT KITS

Roadvision’s range of tube mount kits provide professional mounting solutions for installing bar and driving lamps on bull bars. With tube mount kits available

for 1.5” to 3” diameter tube, they provide a sturdy yet quick and easy mounting solution for our complete range of forward lighting products.

RBC4954BUniversal Bull Bar Clamp Bracket

49-54mm (2”) Tube Black 8x25mm Mounting Hole (Pair)

RBC6065BUniversal Bull Bar Clamp Bracket 60-65mm (2 1/2”) Tube Black 8x25mm Mounting Hole (Pair)

RBC4954SUniversal Bull Bar Clamp Bracket

49-54mm (2”) Tube Silver 8x25mm Mounting Hole (Pair)

RBC6065BUniversal Bull Bar Clamp Bracket 60-65mm (2 1/2”) Tube Silver 8x25mm Mounting Hole (Pair)

RBC6671BUniversal Bull Bar Clamp Bracket 66-71mm (2 3/4”) Tube Black 8x25mm Mounting Hole (Pair)

RBC7681BUniversal Bull Bar Clamp Bracket

76-81mm (3”) Tube Black 8x25mm Mounting Hole (Pair)

RBC6671SUniversal Bull Bar Clamp Bracket 66-71mm (2 3/4”) Tube Silver 8x25mm Mounting Hole (Pair)

RBC7681SUniversal Bull Bar Clamp Bracket

76-81mm (3”) Tube Silver 8x25mm Mounting Hole (Pair)

© Copyright Baxters Pty Ltd 2018. All information is found to be correct at time of printing roadvision.com.au // Page 89

AU

XIL

IAR

Y S

PA

RE

& A

CC

ES

SO

RIE

S

BWRC-MVWireless Remote Control Wiring Kit 10-30V 25A 433MHz

50m Range 9 Flash Pattern + SOS Mode IP67

LICENCE MOUNT KITS

Roadvision’s licence mount bracket provides a professional mounting solution

for installing bar and driving lamps on vehicles without a nudge or bull bar.

Simply mount behind your number plate and you have a quick and easy

mounting solution for our complete range of forward lighting products.

SECURITY MOUNT KITS

Protect your investment with Roadvision’s security lock nut kits, suitable for

our complete range of LED bar & driving lamps, they provide an anti-theft

solution and added piece of mind.

ADJUSTABLE MOUNT KITS

Signature red neoprene shock and vibration absorbers for ultimate

performance and stability. The adjustable side mounts feature 6/9 height

settings using cleaver rubber cam isolators. Designed with 2/3 slots, each

slot can be top, centre or bottom mounted allowing for precise positioning.

FLASHER MODULES

Add additional functionality to our range of LED bar or work lamps with

Roadvision’s remote controlled LED flasher module. Featuring 10 flash

patterns, 10-30V 25A input, our LED flasher modules deliver complete

control and total

WIRING KITS

Roadvision’s wiring kits are a

complete DIY solution providing

a professional installation for bar

and driving lamps. Complete with

harness, relays, switches, plugs and

connectors, our wiring kits make

installation quick and easy.

� Complete wiring harness kits for driving & bar lamps

� Suitable for 12V or 24V vehicles

� Plug & play H4 piggy back connector

� Waterproof Deutsch or ATP connectors

� Supplied with 12V & 24V relays

� Completed with illuminated rocker switch

� Works on both positive & negatively switched

head lamp systems

� Simple DIY fitment

RBKLKLock Nut Kit Suit Bar Lights (Main

Bolt M8x1.5mm x 2 - Side Bolts M8 x 2 - Includes 2 x Tools)

RBDLKLock Nut Kit Suit Driving Lights

(Main Bolt M10x1.5mm x 2 - Side Bolts M8 x 8 - Includes 2 x Tools)

RALPBUniversal Licence Plate Mount Bracket

Fits Standard & Slimline Plates

RAM20006 Position Adjustable End Bracket

Kit Suits SR2 Series (Pair)

RAM30009 Position Adjustable End Bracket Kit Suits DC2/DXC2 Series (Pair)

RVBWKUniversal Single Bar Lamp Wiring Harness, Deutsch Connector, Bar Lamp Rocker Switch, 30A Fuse

Suits up to 140W Light Bars

1000mm

3000mm

2000mm

RELAY

RVBHWKUniversal Heavy Duty Single Bar Lamp Wiring Harness, ATP Connector, Bar

Lamp Rocker Switch, 30A Fuse Suits 140W or Greater Light Bars

1000mm

3000mm

2000mm

RELAY

RVDWKUniversal Driving Light Wiring Har-ness, Deutsch Connectors, Driving

Lamp Rocker Switch, 30A Fuse Suits Pair Driving Lights

1000mm

3000mm

3000mm

2000mm

RELAY

© Copyright Baxters Pty Ltd 2018. All information is found to be correct at time of printingPage 90 // roadvision.com.au

AU

XIL

IAR

Y S

PA

RE

& A

CC

ES

SO

RIE

S

FITTING INSTRUCTIONS1. Remove the main ground from the negative (B-) battery terminal. WARNING: This may result in a loss of radio security code and clock settings.

Consult your owner’s manual before disconnecting.2. Install driving lamps to vehicle on a suitable mounting surface away from exhaust

system or turbo.3. Find a suitable place within the engine bay and mount the receiver box ensuring

that the cables are long enough to reach the battery, driving lamps and high beam wire.

4. Identify the driving lamp connection leads from the receiver module; these are fitted with 2 pin Deutsch connectors.

5. Plug the driving lamp leads into your Roadvision driving lamps using either the 2 pin waterproof Deutsch connectors or female push on terminals. Take care to ensure the black lead is connected to battery negative input (B-) and red lead is connected to battery positive input (B+) to your driving lamps.

6. Identify the blue high beam feed wire from the receiver module.7. Using a multimeter or test light find the active high beam switching wire located

at the back of the head lamp. 8. Cut wire in a suitable position and feed both ends along with the blue high beam

feed wires into the supplied 3M Gel filled connector. Crimp connector with a suitable pair of pliers.

9. Identify the main battery connection leads from the receiver module; these are fitted with 8mm ring terminals.

10. Connect the 8mm battery positive (Red B+) and battery negative (Black B-) leads to the vehicles main battery terminals using the 8mm ring terminals.

11. Re-connect the main battery negative (B-) terminal12. Secure all excess wire to the vehicle.13. Plug in the cigarette lighter transmitter module into your cigarette lighter plug

inside the vehicle.14. Test the driving lamps by turning on the ignition, transmitter switch to ON and

head lamp switch to high beam.

If the lights do not operate correctly, check the following:• Check switch operation – Green LED illuminated with lamps OFF and ignition ON,

red & green LED’s illuminated with switch ON and ignition ON.• Check that you have followed all installation steps• Inspect the fuse holder for blown fuse• Inspect battery terminal connections• Check 3M Gel filled connector connectionNote 1: This wiring harness is designed for use with 2 lamps only not exceeding 10

amps per light or a maximum output of 20 amps. Note 2: By law in Australia, driving lamps must be operated through both the vehicles

high beam circuit and an additional ON/OFF switch. For applications outside Australia or where driving lamps are not being connected, simply connect the blue high beam feed wire to battery positive (B+).

EASY TO FIT…• Mountreceiverboxinenginebay• PlugdrivinglampsinusingeithertheDeutschplugs

or push on terminals • ConnectB+&B-wirestobatteryusing8mmringterminals• Cuthighbeamwireandfeed2sidesofthehighbeamwireandhigh

beam feed from receiver into 3M connector• Crimpusingastandardpairofpliers• Plugcigarettelightertransmitterintocigarettelighterplug

PART NUMBER: RCWL

Deutsch DT 2 Pin Connectors

To Driving Lamps

Female Push on Terminals

100mm Harness

To Vehicle High Beam

3M Scotchlock IDC Tap Connector UG

2m High Beam Wire

1m Sheathed Harness

2m S

heat

hed

Har

ness

Receiver Module

Transmitter Module

8mm Ring Terminal

8mm Ring Terminal

In-Line Fuse 20A Blade

B+

B-

Vehicle Battery

© Copyright Baxters Pty Ltd 2018. All information is found to be correct at time of printing roadvision.com.au // Page 91

Lamps OFF Transmitter Illuminated Green only

Lamps ONTransmitter Illuminated Red & Green

RCWL - AIRWIRERemote Control Wiring Loom KitFits UNIVERSAL DRIVING LAMPS

AIRWIRE™ takes all the effort out of installing driving lamps… A simple kit that can be easily fitted by workshops or the DIY handyman. No need to drill holes

in the firewall or mount switches in the dash… Simply mount the receiver box and connect directly to the battery, splice in the high beam feed, plug in the

driving lamps and cigarette lighter transmitter and you are done… It’s that easy.

REMOTE WIRING KITS

AU

XIL

IAR

Y S

PA

RE

& A

CC

ES

SO

RIE

S

Universal Remote Wiring Accessories

WIRELESS TECHNOLOGY FITTING DRIVING LAMPS HAS NEVER BEEN SO EASY!• Easy to install complete DIY kit - 30 min• Suitable for the average home handyman• Requires only basic tools for installation• No drill ing holes through the firewall and dash• Kit can be easily moved from vehicle to vehicle• Multi-Volt 9-32V DC Input• Fully potted electronics & waterproof• 5m transmitter range & 3m plug & play harness• 20A maximum output• Deutsch & 3M gel fil led connectors

© Copyright Baxters Pty Ltd 2018. All information is found to be correct at time of printingPage 92 // roadvision.com.au

Spares & Accessories

B817-49AMP Plug 3 Pin 200mmFits LUMENX SERIES

B817-49LAMP Plug 3 Pin 2.5mFits LUMENX SERIES

B817-491 AMP Plug 3 Pin to PL3 Adaptor

TLCM30Trailer Lamp Timer Module 30 MinuteFits INTERIOR LAMPS

TLCM60Trailer Lamp Timer Module 60 MinuteFits INTERIOR LAMPS

TLCM180Trailer Lamp Timer Module 180 MinuteFits INTERIOR LAMPS

TLCM1Trailer Lamp Timer Module Wiring HarnessFits INTERIOR LAMPS

WIRING ACCESSORIES & CHARGERS

RVMBUU Mounting Bracket Stainless SteelFits UNIVERSAL SUIT WORK LAMPS

181111261Magnetic Base Mounting KitFits UNIVERSAL

417-3Mounting Bracket TripleFits 1217/817 SERIES

B426-18Grommet RubberFits 1217 SERIES

BBL-BKT01Replacement Sliding Bracket Universal (Pair)

BBL-BKT02Replacement End Bracket Rollar Series (Pair)

BBL-BKT05Replacement End Bracket DC/DCS/DCSX/DCX Series (Pair)

BBL-BKT04Replacement Sliding Bracket SR Series (Pair)

BRACKETS & MOUNTING ACCESSORIES

AU

XIL

IAR

Y S

PA

RE

& A

CC

ES

SO

RIE

S

BPLC1536” Clip on Clear Protective Cover to suit DC/DCS Series 85 x 153mm

BPLC2038” Clip on Clear Protective Cover to suit DC/DCS Series 85 x 203mm

BPLC24010” Clip on Clear Protective Cover to suit SR Series 57 x 240mm

BPLC-1080Clip on Clear Protective Cover to suit BDL1080 Series

COVERS