AT-UHD-SW-52ED - SnapAVatlona.com 5 Toll free: 1-877-536-3976 Local: 1-408-962-0515 HDMI 1 HDMI 2 HDMI 3 HDMI 4 HDMI 5 VOLUME AT-UHD-SW-52ED R IN IR OUT - + + - L FW LAN RS-232 P S

4K/UHD 5 Input HDMI Switcher with Mirrored HDMI and

HDBaseT Outputs and PoE

atlona.comToll free: 1-877-536-3976

Local: 1-408-962-0515

User ManualAT-UHD-SW-52ED

Please check http://www.atlona.com/product/AT-UHD-SW-52EDfor the most recent firmware

update or manual.

2atlona.comToll free: 1-877-536-3976

Local: 1-408-962-0515

Table of Contents1. Introduction ................................................................................................... 32. Package Contents ................................................................................................... 33. Features ................................................................................................... 34. Category Cable ................................................................................................... 44. Panel Descriptions a. Front ................................................................................................... 5 b. Back ................................................................................................... 55. Remote Control ................................................................................................... 56. Captive Screw ................................................................................................... 67. Audio ................................................................................................... 78. TCP/IP ................................................................................................... 8-169. RS-232 & TCP/IP a. Terminal ................................................................................................... 17 b. Connection ................................................................................................... 17 c. Commands ................................................................................................... 18-19 d. IP Commands ................................................................................................... 19 e. Baud Rate ................................................................................................... 20 f. 3rd Party Control ................................................................................................... 2010. Connection Diagram ................................................................................................... 2011. Specifications ................................................................................................... 21 12. Safety ................................................................................................... 2213. Warranty ................................................................................................... 23-2414. Registration ................................................................................................... 24

Firmware 1.2.04 (02/2017) Commands added Pg. 18, 19, 20


Local: 1-408-962-0515

• 1 x UHD-SW-52ED • 1 x 48V DC power supply (AT-PW48V0.83A-CAPT)• 4 x Female captive screw connector (5pin: analog audio & IR, 3 pin: RS-232, and 2 pin: power)• 1 x Short rack ear

• 1 x Long rack ear• 2 x Mounting plates• 1 x Remote control• 4 x Rubber feet• 1 x User Manual

Rack Ear x 1

Rack Ear x 1

Mounting Plate x 2

• Mirrored HDMI and HDBaseT output• Automatic display control using TCP/IP/RS-232 commands, or CEC• Auto switching with video detection technology (activated through RS-232 or webGUI)• Analog audio de-embedding through captive screw connector• +4 dBu balanced analog audio output• Control volume using webGUI, IR, TCP/IP, or RS-232• Supports 4K @ 60Hz 4:2:0 or 4K @ 30Hz RGB with 8 bit color• Supports Dolby® TrueHD and DTS-HD Master Audio™ when using an HDMI for audio input and output• Digital audio de-embedding through the S/PDIF output for up to DTS™ 5.1 and Dolby® Digital• Extended distance HDBaseT port w/PoE to power compatible receivers up to 100 meters (328 feet) away• HDCP management• EDID management• Easy to use webGUI through Ethernet connection• Half-rack size• Comes with rack mount ears and mounting plates

The UHD-SW-52ED can be mounted in three ways: as a single unit in a rack, with a second unit in a rack, or against a wall/table using the mounting plates.

Single unit mounting will use the long rack ear and short rack ear to affix the unit to the rack.

Two unit mounting will use two short rack ears (the second will be in the box with the second unit) and two mountings plates to affix the two units together inside the rack.

Wall/table mounting will use both mounting plates to affix the unit to a table or wall.

Oval holes on the rack ears will always be attached to the rack.

Circular holes will always be attached to the unit.

Larger oval hole will be attached to the wall/table.

Introduction

Features

Package Content

The 4K/UHD 5 input HDMI switcher with mirrored HDMI and HDBaseT output supports 4K @ 60Hz, Ethernet transmission/support/management, RS-232, IR, and TCP/IP control along with a webGUI for easy set up. Built in display control enables the switcher to automatically turn the display on/off (through TCP/IP or RS-232), control volume, and more. With control, audio de-embedding, and EDID/HDCP management the UHD-SW-52ED will ensure the best audio and video experience.


Local: 1-408-962-0515

Category Cable

For the category cables used in the installation of these products, please be sure to use a 568B termination as pictured below:

Connector type and size is very important to ensure extenders work correctly. Please use the matching cable type with the correct RJ45 connector.

CAT5e cables should use only CAT5e RJ45 connectorsCAT6 cables should use only CAT6 connectorsCAT6a cables should use only CAT6a connectorsCAT7 cables should use only CAT7 connectors

Using the wrong size connectors may result in interference causing loss of signal.

Important! “EZ RJ45 connectors” are not recommended with HDBaseT extenders. Doing so may result in interference with audio and video transmission.

Use the table below to verify the best category cable for the installation.

Important! 4K (UHD) signals are sensitive to cable quality and installation technique. It is recommended to use CAT6a/7 solid core cables for best results.Note: For cable distances see the specifications on page 20

Performance Rating Type of LAN cable

Wiring Shielding CAT5e/6 CAT6a/7

Solid Shielded (STP/FTP) *** ****

Unshielded (UTP) ** N/A

Stranded - Patch cable(Not recommended)

Unshielded (UTP) * N/A

Shielded (STP/FTP) * N/A

Termination Please use EIA/TIA-568-B termination

1. White - Orange2. Orange3. White - Green4. Blue5. White - Blue6. Green7. White - Brown8. Brown

Connector


Local: 1-408-962-0515

HDMI 1

HDMI 2

HDMI 3

HDMI 4

HDMI 5

VOLUME

AT-UHD-SW-52ED

R INIR

OUT

+ + --

L

FW LAN

RS-232

RXP S S TX

DC 48VHDMI IN HDMI OUT HDBaseT OUT

AUDIO

S/PDIF OUT

1 2 3 4 5

POWER INPUT

- +

HDMI 1

HDMI 2

HDMI 3

HDMI 4

HDMI 5

VOLUME

AT-UHD-SW-52ED

R INIR

OUT

+ + --

L

FW LAN

RS-232

RXP S S TX


AUDIO

S/PDIF OUT

1 2 3 4 5

POWER INPUT

- +

Back Panel

1. HDMI IN - Connect sources here2. HDMI OUT - Connect to an HDMI display, extender, or switcher3. HDBaseT OUT - Connect to an HDBaseT PoE receiver (e.g. AT-UHD-EX-100CE-RX)4. FW port: Firmware update port, connect a Mini USB to USB A cable to a computer5. LAN port - Connect network switch or router to this port for Ethernet, TCP/IP, or webGUI control6. DC 48V: Connect included captive screw, 48V DC power supply here7. Audio output - Connect to an amplifier, mixer, DSP, audio receiver, or other audio device8. IR port - Connect IR control system or compatible IR emitter/receiver to this port9. RS-232 port - Connect control system to RS-232 port

Remote Control

1

1

2

2 3

5

6

7 98

3

4

4

5

1. Power On/Off: Turn switcher power on and off2. Video On/Off: Turns video output off and on3. Input selection: Selects source 4. Audio control: Adjust volume up/down Mute: Mute output audio

Note: Setup buttons are not functional for the UHD-SW-52ED switcher

Panel DescriptionsFront Panel

1. HDMI LEDs - Illuminates to indicate the selected source2. Volume LEDs - Displays the volume level3. Power Button - Turns switcher on, places the unit in standby mode, or control a connected display through the HDBaseT output4. Volume up/down - Adjusts output volume or display volume through the HDBaseT output5. Input Button - Switches between HDMI inputs

SW-R1

Setup

Video 1

Video

Video 2

All On

Power

Vol +

Vol -

Menu

Return

Enter

Mute

1

3

2

4

5

Input Audio

On Off

On Off

On Off

1

2

3 4


Local: 1-408-962-0515

Captive ScrewThe captive screw connectors allow you to cut cables to a suitable length, reducing cable clutter while providing a more reliable connection.

Connecting

The captive screw connectors have a contact bar that is adjusted to compress the wire against the top contact plate. Use the screws at the top of the connector to compress the wire against the contact plate.

When connecting the cables to the female captive screw connector it is important that the wires be terminated correctly. The female captive screw connector has a contact plate at the top and must have the wires touching it for signal to pass. When wired correctly (see picture A) the signal will pass, incorrectly (see picture B) no signal will pass.

Female captive screw connectors are included: Power (see picture 1), RS-232 (see picture 2), and IR (see picture 3).

The power cable (picture 4) will have exposed wires. Each wire is encased in a different colored cover.

1

Power RS-232

Clockwise CounterClockwise

Turn the screws clockwise to raise the contact bar to the upper contact plate and hold the wires in place.

Turn the screws counter clockwise to lower the contact bar to release the wires.

A B

2

RS-232 pin out will be determined by the RS-232 cable and will connect as Rx (receiver), Tx (transmitter), and (ground). (See picture 5)

Pin out color will differ per RS-232 cable.Black: - White: +

- +4 5

Note: The IR receiver and IR transmitter is optional for the UHD-SW-52ED. The compatible IR receiver (AT-IR-CS-RX) and IR transmitter (AT-IR-CS-TX) can be purchased through atlona.com.

The wires of the emitter and receiver have been marked to differentiate the pin outs.

The included IR emitter has two wires: signal and ground. Signal will have a solid line and ground will be blank. The IR emitter will plug into the IR OUT ports.

There are three wires on the IR receiver (sold separately): signal, ground, and power. Signal has a dotted line, ground will be blank, and power will have a solid line. The IR receiver will plug into the IR IN ports.

IR

3

Signal (S) Ground ( )

Signal (S)Ground ( )Power (P)


Local: 1-408-962-0515

Tip (+)

Analog Audio

A captive screw analog audio connector is provided to ensure a more reliable and secure connection. The captive screw connector supports balanced and unbalanced audio output.

Balanced audio connections use two signal wires and a ground to minimize interference to audio signals. Unbalanced audio connections use one signal wire and a ground and are used if other system components don’t support balanced signals.

Important! With unbalanced connections a jumper is needed between ground and negative to reduce noise

Note: Pin outs may vary, please refer to the audio device’s manual to ensure a correct connection.Important! When terminating cables, please ensure exposed adjacent wires do not touch. This may result in a short that can damage connected devices.

XLR RCA

Sleeve ( Ground)

+

++

++

2 ( + )

3 ( - )

1 ( )

+-

--

-- -

L / R

BALANCED UNBALANCED

L / R

+ +


Local: 1-408-962-0515

Ethernet

For convenience, the UHD-SW-52ED comes with DHCP on. This enables the switcher to be connected to a network without knowing available IP addresses. If your network does not allow dynamic IP addresses or if you are using the switcher with a TCP/IP control system, this feature may be turned off and the IP address set using RS-232 commands or the webGUI.

WebGUI

Atlona has created an easy to use webGUI for initial setup and later changes to the configuration of the switcher.

To begin, plug a LAN cable into the LAN port of the UHD-SW-52ED and the network switch, then type the IP address of the unit into a web browser of a PC connected to the same network (as seen below).

To find the switcher IP: use RS-232 command “IPCFG”.

Important: If any stability issues are experienced, disable any anti-virus or firewall that may interfere with network communication to the switcher. Once set up is done and the switcher webGUI is no longer used, the firewall and anti-virus can be re-enabled.

A login screen will appear (this is the same log in for admin and general users). For the first log in (and future admin changes) the username is “root” and password is “Atlona”.

Note: Only the admin password can be changed (see page 9). The username will always remain “root”.

Note: IP addresses may also be found using common free IP scanner software such as “Advanced IP Scanner”


Local: 1-408-962-0515

The home screen tab will display the general system information.

The Network Setup Page will allow the IP information to be changed. When a change is made the screen will grey and the ability to save or cancel will display at the bottom.

Note: When DHCP is on, the IP address cannot be configured. Turn DHCP off to enable IP configuration.Note: For a stable connection when using a control system, it is best to set up a static IP. As you select an IP address, make certain no other devices on your network are using that IP address.

Login Mode has been added to provide a secure telnet login. Once Login Mode has been turned on a username and password will be required on all IP connections to the switcher.

Note: Login mode should be in off position when the UHD-SW-52ED is used with control systems that do not support passwords. If your control system supports password protection, you can turn login mode on. The webGUI always requires a password.Note: The username and password used in IP Login Mode will be the same login information as the webGUI.


Local: 1-408-962-0515

System Settings Auto Switch - Turn auto switching on/off. Default is off.Video Settings Source - Select one of the five inputs to be routed to the output.Audio Settings Volume - Adjust output volume up or down


Local: 1-408-962-0515

The Config Page will allow the admin password to be changed, users to be added, and the RS-232 ports to be configured.

Note: User information will display for the admin only. Up to 3 users other than admin can be added.Note: Only the admin password can be changed. The username will always remain “root”. If the admin password is lost the system must be returned to factory settings and setup repeated.


Local: 1-408-962-0515

The EDID Page enables the input preferred timing to be selected and HDCP compliance reporting to be set.

HDCP selection allows the HDCP reporting of the input to be changed between compliant and non-compliantNote: This function is controllable through RS-232 and TCP/IP.Note: UHD-SW-52ED protects HDCP encoded content and will not pass HDCP content to a non-HDCP compliant device.Note: Some devices flag all content as protected when connected to an HDCP compliant display. This prevents what should be non-protected content from reaching devices (e.g. teleconference system) through the UHD-SW-52ED.Note: When HDCP reports as non-compliant, only user created content is transmitted. Protected content from all sources (e.g. Blu-ray, AppleTV, etc) is blocked.

Note: To ensure compatibility, it is best to set the EDID to match the native resolution of the connected display and the audio format of the connected sound systemNote: To use the analog audio output, a 2Ch EDID will need to be selected

EDID Saved Save the current output’s EDID to memory. There are eight total EDID memories to save to.

Note: Internal EDIDs include audio EDIDs as well. 2Ch is two channel audio, MCh is multi-channel audio (including up to Dolby TrueHD or DTS-HD Master Audio), DD is Dolby Digital, and DVI does not include audio.

Internal EDIDs -STD Sink (pass through) Int_1 1080P 2Ch Int_2 1080P MCh Int_3 1080P DD Int_4 1080P 3D 2Ch Int_5 1080P 3D MCh Int_6 1080P 3D DD Int_7 720P 2CH Int_8 720P DDInt_9 1280x800 2Ch Int_10 1366x768 2Ch Int_11 1080P DVIInt_12 1280x800 DVI Int_13 3840x2160 2Ch Int_14 3840x2160 MCh


Local: 1-408-962-0515

The Control Page includes settings which enable display controls by the switcher. It provides a way to program button functions, turn auto switching on/off, and determine the type of control commands (TCP/IP or RS-232) sent out.

Button Control Selection

Power - Set which device the power button controls None: Power button will turn the UHD-SW-52ED on and off RS-232: Power button will send power on/off command over HDBaseT using RS-232 to compatible receivers and displays IP: Power button will send power on/off command over Ethernet using either the LAN connection or the HDBaseT connection Volume/Mute Audio Out: Volume and mute buttons will control volume output of the switcher RS-232: Volume/Mute buttons will send the commands over HDBaseT using RS-232 to compatible receivers and displays IP: Volume/Mute buttons will send the commands over Ethernet using either the LAN connection or the HDBaseT connection

CEC Control

Power On - Sends a command over HDBaseT to the HDMI output of the connected receiver to turn the connected display on Off - Sends a command over HDBaseT to the HDMI output of the connected receiver to turn the connected display off Note: CEC may not work with every display type


Local: 1-408-962-0515

System Settings

Display Auto Power On - When enabled, the unit will send a programmed command to the display to turn on after detecting an A/V signal Display Auto Power Off - When enabled, the unit will send a command to the display to turn off after not detecting an A/V signal Lamp Cool Down Timer (10-300) - Used with a projector whose lamp cannot be turned on for up to 5 minutes after being shut off. Match settings with lamp delay on projector Auto Power off timer (10-240) - Sets the period of time between the loss of A/V signal and when the “Display Off” command is sent Note: LED will blink red for the auto power off time period then go solid Note: All functionality remains, only the HDBaseT output is turned off Display Warm Up Timer (10-300) - Sets the period of time after the display is turned on, that the power button will be locked Note: LED will blink green for the warm up timer period and then stay solid Note: When timers are set to 0 seconds, they will disable the timers’ functions Control Type - Select whether the display on/off commands are sent using RS-232, TCP/IP, or CEC Feedback Verify On: If receiving no feedback, the product will send the command up to 4 times Off: The command will only be sent once, whether feedback is received or not


Local: 1-408-962-0515

TCP/IP Settings of Controlled Device

This option sets the IP for display control. The static IP set here should match the display’s static IP. To set or view the display’s IP address, check the display’s user manual.

Note: The switcher and the display must be on the same network for these commands to work Note: Be sure the static IP address set for the display does not match any other device on the network

IP Mode Non-login: Does not require a username and password when using TCP/IP to control the display Login: Requires a username and password to control the display through TCP/IP IP Address & Port - Set to match the display’s static IP Username & Password - Required when in login mode Save - Saves the IP settings for accessing the controlled device

RS-232/IP Commands

ASCII/Hex - Set which type of commands are sent to the display On/Off/Volume+/Volume-/Mute - Enter the specific commands and feedback that will be sent/ received when using any of the control options Note: Individual commands will be found in the display’s manual End of line symbols - None, CR, LF, CR-LF, Space, STX, ETX, Null - Select the appropriate symbol from the drop down list. Carriage return, line feed, and carriage return with line feed are the most commonly used symbols. Note: Be sure to check the display’s manual for the correct symbol


Local: 1-408-962-0515

For the best performance ensure the most current firmware is being used. Atlona frequently updates firmware to add features, improve compatibility, and fix bugs. If any issues are experienced with the switcher, check to make sure the most current firmware is installed.

Download the latest firmware from http://www.atlona.com/AT-UHD-SW-52ED to a specific place on the computer, unzip the firmware file, then update the unit using the browse and upload buttons.

Click the browse button and select the firmware to be loaded from the PC. Once selected, press the upload button. The progress bar displays the progress of the firmware update.

The Valens (HDBaseT) port has a separate firmware. This firmware can be found at http://www.atlona.com/AT-UHD-SW-52ED.

Click the browse button and select the Valens (HDBaseT) file that was downloaded. Once selected, press the upload button, the progress bar displays the progress of the firmware update.


Local: 1-408-962-0515

RS-232 & TCP/IP

To set up the RS-232 terminal the first thing needed is to find the RS-232 communications port under the computer’s device manager. Once there, right click the port and select “Properties”. Under the properties menu select the port settings tab and set the menu to the switcher default:

Bits per second: 115200, Data bits: 8, Parity: None, Stop bits: 1 and Flow control: None.

Terminal

Connection

RS-232 is connected through a 9-pin female D connector. Three pins will have specific functions associated with them, some are unassigned.

No. Pin Function1 ---- Not used2 Tx Transmit3 Rx Receive4 ---- Not used5 Gnd Ground6 ---- Not used7 ---- Not used8 ---- Not used9 ---- Not used

5 4 3 2

9 8 7 6

1

B

A

C


Local: 1-408-962-0515

Commands (TCP/IP and RS-232)

The command codes are case sensitive, do not change capitalization, spacing, or lettering.

Command Feedback Description

PWON PWON Turns switcher on

PWOFF PWOFF Turns switcher off

PWSTA PWSTA Displays power status

VersionXE.g. Version OSD

VersionXE.g. Version x.x.xx

Displays the software versions: ex. VersionMCUfirmware [MCU]OSD menu [OSD]DSP [DSP]FPGA [FPGA]

Type AT-UHD-SW-52ED Displays the model information

REBOOT REBOOT Reboots the AT-UHD-SW-52ED

Mreset Mreset Reset device to manufacture default

Lock Lock Locks the front panel buttons

Unlock Unlock Unlocks the front panel buttons

x3AVx1 x3AVx1 Switch inputs Ex. Switch output 1 to input 4= x4AVx1

Status x2AVx1, x3AVx2 Displays what input is connected to the what output

x1$ X x1$ on Turns on/off output channel (X= on, off, sta)E.g. x2$ off - Turns output 2 off

AutoSW X AutoSW on Turns auto switching on/off (X= on, off, sta)

IRON IRON Turns on the IR receiver window

IROFF IROFF Turns off the IR receiver window

EDIDCopyX memYE.g. EDIDCopy1 mem2

EDIDCopyX memYE.g. EDIDCopy1 mem2

Save the EDID of output X (1 or 2) to memory Y (1-8)E.g. Copy EDID of output 2 to memory 5 = EDIDCopy2 mem5

EDIDMSetX default EDIDMSetX default Set the EDID of the input to the default EDID

EDIDMSetX saveY EDIDMSetX saveY Set the EDID of an input to the previously saved EDID memoryE.g. EDIDMset3 save1 - sets input 3 to EDID memory 1

EDIDMSetX intY EDIDMSetX intY Sets the EDID of an input to one of the internal EDIDsE.g. EDIDMSet2 int3 - Sets input 3 to internal EDID 3

HDCPSetX YE.g. HDCPSet1 on

HDCPSetX YE.g. HDCPSet1 on

Set HDCP reporting mode of the HDMI input (X= 1-5)(Y= on, off, sta)E.g. Input 3 to report HDCP non-compliant = HDCPSet3 off

AudioOutX Y AudioOutX on Turns the HDMI audio of each output (X= 1, 2) on/off (Y= on, off, sta)E.g. Turn Output 2 HDMI audio off = AudioOut2 off

VOUT1 + VOUT1 XX Increases volume output by 1

VOUT1 - VOUT1 XX Decreases volume output by 1

VOUT1 YYE.g. VOUT1 -60

VOUT1 XXE.g. VOUT1 -60

Set volume output to a specific value (XX= -80 to 6)

VOUT1 sta VOUT1 YY Displays current volume output

VOUTMute1 X VOUTMute1 X Mute or unmute the output volume (X= on, off, sta)

Each command or feedback is terminated with a carriage return.Note: If the command fails or is incorrect the feedback is “Command FAILED”

Note: Preferred timings include audio EDIDs as well. 2Ch is two channel audio, MCh is multi-channel audio (including up to Dolby TrueHD or DTS-HD Master Audio), DD is Dolby Digital, and DVI does not include audio.

[Y] preferred timing -STD Sink (pass through) 1 1080P 2Ch 2 1080P MCh 3 1080P DD 4 1080P 3D 2Ch 5 1080P 3D MCh 6 1080P 3D DD 7 720P 2CH 8 720P DD9 1280x800 2Ch 10 1366x768 2Ch 11 1080P DVI12 1280x800 DVI 13 3840x2160 2Ch 14 3840x2160 MCh


Local: 1-408-962-0515

Command Feedback DescriptionSetCmd x[y]

e.g. SetCmd on[PWR ON]

SetCmd x[y]

e.g. SetCmd on[PWR ON]

Sets the RS-232 or IP command for the selected button or function x = on, off, vol+, vol-, and mute y = commande.g. Set the on command to send the command PWR ON

SetEnd x[y]

e.g. SetEnd off[CR-LF]

SetEnd x[y]

e.g. SetEnd off[CR-LF]

Sets the line termination for the chosen command x = on, off, vol+, vol-, mute, fbkon, fbkoff, fbkmute y = None, CR, LF, CR-LF, Space, STX, ETX, and nulle.g. Set the command off to have a carriage return and line feed

TrigCEC ye.g. TrigCEC on

TrigCEC ye.g. TrigCEC on

Triggers the stored CEC command to turn the display on and off y = on, off

TrigRS ye.g. TrigRS vol+

TrigRS ye.g. TrigRS vol+

Triggers the RS-232 command from RS-232 or IPy = on, off, vol+, vol-, and mute

TrigIP ye.g. TrigIP vol-

TrigIP ye.g. TrigIP vol-

Triggers the IP command from RS-232 or IPy = on, off, vol+, vol-, and mute

CtlType xe.g. CtlType rs-232

CtlType xe.g. CtlType rs-232

Sets the control type x = ip, rs-232, cece.g. Set the control type to RS-232

CliMode xe.g. CliMode non-login

CliMode xe.g. CliMode non-login

Sets the control device’s IP mode x = sta, login, non-logine.g. Sets the IP mode to non-login

CliUser xe.g. CliUser

CliUser xe.g. CliUser admin

Sets the IP username for login x = username, (blank)e.g. Display the IP username by leaving x blank

CliPass xe.g. CliPass AtlonA

CliPass xe.g. CliPass AtlonA

Sets the IP password for login x = password, (blank)e.g. Set the IP password to AtlonaA

CliIPAddr xe.g. CliIPAddr sta

CliIPAddr xe.g. CliIPAddr 192.168.0.23

Sets the IP address of the controlled device x = ip, stae.g. Display the IP address of the controlled device

CliPort xe.g. CliPort 24

CliPort xe.g. CliPort 24

Sets the IP port of the controlled device x = port, stae.g. Set the IP port to 24

LampCool x e.g. LampCool 120

LampCool x e.g. LampCool 120

Sets the lamp cool-down duration, in seconds. Match this setting with the lamp delay on the projector (X= 0 to 300)

SetOff x e.g. SetOff 60

SetOff x e.g. SetOff 60

Sets the time interval, in seconds, between the loss of A/V signal and when the “Display Off” command is sent (X= 10 to 240)

DisWarmUp x e.g. DisWarmUp 60

DisWarmUp x e.g. DisWarmUp 30

Sets the time interval, in seconds, after the display is turned on, that the power button will be locked (X= 0 to 300)

Zone output parameter commands (for display control)

RS232para1[baudrate,data-length,parity,stop-bit]

Example: To change the output baud rate to 19200 use RS232para1[19200,8,0,1]

RS232zone1[command]

Once the switcher and zone output have been set up for the best communication, commands can be sent to control the display. The commands will come from the user manual of the display or projector. The commands and any carriage returns/line feeds in the commands will need to be placed in the bracket.

Example: To turn the display or projector on if the command is PWRON carriage return, use the command: RS232zone1[PWRON carriage return]

Note: Use this command if the connected display uses a different baud rate

Note: Use this command if the connected control system does not output 115200

Switcher parameter commandCSpara[baudrate,data-length,parity,stop-bit] (data-length, parity, and stop-bit for switcher must be 8,0,1)

Example: To change the baud rate to 38400 use CSpara[38400,8,0,1]

Baud RateDefault baud rate to control the switcher is 115200 and default baud rate to control the display or projector is 9600. Note: For the display’s actual baud rate, refer to the owner’s manual

To change the baud rate of the switcher (for switcher control) or the zone output (for display/projector control), the commands below will be needed


Local: 1-408-962-0515

Command Feedback DescriptionIPCFG IP Addr : x.x.x.x

Netmask : x.x.x.xGateway : x.x.x.xIP Port : x

Displays IP address configuration

IPQuit IPQuit Logs out of TCP/IP ConnectionIPAddUser X YE.g. IPAddUser Atlona 1234

TCP/IP user was added Adds a user for TCP/IP controlX= user and Y= Password

IPAddUser username passwordusername password username password

Displays a list of users and passwords

IPDelUser X TCP/IP user was deleted Delete a user from TCP/IP X= usernameIPDHCP X IPDHCP X Turns DHCP on or off X= on, off, staIPStatic X Y ZE.g. IPStatic 192.168.1.1 255.255.255.0 192.168.1.200

IPStatic X Y ZE.g. IPStatic 192.168.1.1 255.255.255.0 192.168.1.200

Sets static IP addressIPStatic Address(X) Netmask(Y) Gateway(Z)

IPPort X IPPort X Set the TCP/IP PortIPLogin XE.g. IPLogin off

IPLogin XE.g. IPLogin off

Enables IP LoginX= on, off, sta

Broadcast XE.g. Broadcast on

Broadcast XE.g. Broadcast on

Sets broadcast mode on or offX= on, off, sta

InputBroadcast x E.g. InputBroadcast on

InputBroadcast x E.g. InputBroadcast on

Sets the input broadcast reporting statusX= on, off, sta

InputStatus E.g. InputStatus

InputStatus E.g. InputStatus 11001

Displays the input status for each input 1 = active input, 0 = no source connection

InputStatusX E.g. InputStatusX

InputStatusX Y E.g. InputStatus2 1

Displays the input status for the specified input. X= input number, and Y is returned for the source status: Y=0 is no source connection, Y=1 is active input

IPTimeout XXE.g. IPTimeout 300

IPTimeout XXE.g. IPTimeout300

Determines amount of seconds of inactivity before TCP/IP disconnects

Each command or feedback is terminated with a carriage return.Note: If the command fails or is incorrect the feedback is “Command FAILED”

IP Commands

3rd Party ControlThe UHD-SW-52ED is compatible with most 3rd party control systems. TCP/IP and RS-232 commands can be passed from 3rd party control systems to the UHD-SW-52ED through the LAN or RS-232 port.

Note: The switcher can also convert TCP/IP commands to RS-232 commands which are then sent to the compatible HDBaseT devices.

The UHD-SW-52ED can take either TCP/IP or RS-232 command protocol and transmit it to a connected device: saving labor, cable, and control system ports.

The RS232zone command re-transmits RS-232 commands to the display through the compatible HDBaseT receiver. The command may be initiated using either RS-232 or TCP/IP commands.

The Display On/Off command may be used to transmit a TCP/IP command by either RS-232 or TCP/IP to a display.


Local: 1-408-962-0515

Connection Diagram

FW LINK

POWER

AT-UHD-EX-100CE-RX

RS-232

RXTX

IR IN

P S

IR OUT

S

HDBaseT IN

ETHERNET

HDMI OUT

AT-UHD-EX-100CE

HDMI 1

HDMI 2

HDMI 3

HDMI 4

HDMI 5

VOLUME

AT-UHD-SW-52ED

R INIR

OUT

+ + --

L

FW LAN

RS-232

RXP S S TX


AUDIO

S/PDIF OUT

1 2 3 4 5

POWER INPUT

- + Control System

MUTE OFF

VCR DVD

CAM PC1

PC2 PC3

+ -

A B

C D

1 2

Video Audio HDBaseT Control


Local: 1-408-962-0515

Specifications

Resolutions Video 4096x2160@24/25/30/50*/60Hz*, 3840x2160@24/25/30/50*/60Hz* (UHD), 2048x1080p, [email protected]/24/25/29.97/30/50/59.94/60Hz, 1080i@50/59.94/60Hz, 720p@50/59.94/60Hz, 576p, 576i, 480p, 480i

VESA 2560x2048, 2560x1600, 2048x1536, 1920x1200, 1680x1050, 1600x1200, 1600x900, 1440x900, 1400x1050, 1366x768, 1360x768, 1280x1024, 1280x800, 1280x768, 1152x864, 1024x768, 800x600, 640x480

Color Space YUV, RGB Chroma Subsampling 4:4:4, 4:2:2, 4:2:0 Color Depth 8-bit, 10-bit, 12-bitAudio Formats - HDMI IN/OUT PCM 2 Ch, LPCM 5.1, LPCM 7.1, Dolby Digital, DTS 5.1, Dolby Digital Plus, Dolby TrueHD, DTS-HD Master Audio Formats - S/PDIF PCM 2 Ch, LPCM 5.1, LPCM 7.1, Dolby Digital, DTS 5.1 Format - captive screw Balanced analog, nominal output: +4dBu, Max output: +18dBu @ 0 dB fs, 2Ch PCM Sample Rate 32 kHz, 44.1 kHz, 48 kHz, 88.2 kHz, 96 kHz, 176.4 kHz, 192 kHzDistance (per port) CAT5e/6 @ 4K up to 70 meters up to 230 feet CAT5e/6 @ 1080p up to 100 meters up to 328 feet CAT6a/7 @ 4K up to 100 meters up to 328 feet HDMI IN/OUT @ 4K up to 5 meters up to 15 feet HDMI IN/OUT @ 1080p up to 10 meters up to 30 feetSignal Bandwidth 10.2 Gbps CEC Pass through HDCP Switchable - Complaint / Non-compliantTemperature Operating 0°C to 50°C 32°F to 122°F Storage -20°C to 60°C -4°F to 140°F Humidity 20 to 90% non-condensingPower Consumption 22W Idle Consumption 9.06W Supply Input: AC100~240V 50/60Hz Output: DC 48V/0.83ADimension H x W x D 44 x 222.25 x 261 (mm) 1.73 x 8.75 x 10.28 (inch) Rack Unit 1/2 rack, 1RUWeight Device 3.15 kg 1.44 lbsCertification Power Supply CE, FCC, cULus, RCM Product CE, FCC

**4096x2160@50/60Hz & 3840x2160@50/60Hz supported @ chroma subsampling 4:2:0 8-bit only


Local: 1-408-962-0515

To reduce the risk of electric shock, do not expose this product to rain or moisture

If the wall plug does not fit into your local power socket, hire an electrician to replace your obsolete socket.

Do not modify the wall plug. Doing so will void the warranty and safety features.

This equipment should be installed near the socket outlet and the device should be easily accessible in the case it requires disconnection.

Safety Information

Safeguards

Precautions

FCC regulations state that any unauthorized changes or modifications to this equipment, not expressly approved by the manufacturer, could void the user’s authority to operate this equipment.

Operate this product using only the included external power supply. Use of other power supplies could impair performance, damage the product, or cause fires.

In the event of an electrostatic discharge this device may automatically turn off. If this occurs, unplug the device and plug it back in.

Protect and route power cords so they will not be stepped on or pinched by anything placed on or against them. Be especially careful of plug-ins or cord exit points from this product.

Avoid excessive humidity, sudden temperature changes or temperature extremes.

Keep this product away from wet locations such as bathtubs, sinks, laundries, wet basements, fish tanks, and swimming pools.

Use only accessories recommended by Atlona to avoid fire, shock, or other hazards.

Unplug the product before cleaning. Use a damp cloth for cleaning and not cleaning fluid or aerosols. Such products could enter the unit and cause damage, fire, or electric shock. Some substances may also mar the finish of the product.

Never open, remove unit panels, or make any adjustments not described in this manual. Attempting to do so could expose you to dangerous electrical shock or other hazards. It may also cause damage to your product. Opening the product will void the warranty.

Do not attempt to service the unit. Disconnect the product and contact your authorized Atlona reseller or contact Atlona directly.


Local: 1-408-962-0515

Atlona, Inc. (“Atlona”) Limited Product Warranty Policy

CoverageAtlona warrants its products will substantially perform to their published specifications and will be free from defects in materials and workmanship under normal use, conditions and service.

Under its Limited Product Warranty, Atlona, at its sole discretion, will either:

A) repair or facilitate the repair of defective products within a reasonable period of time, restore products to their proper operating condition and return defective products free of any charge for necessary parts, labor and shipping

OR

B) replace and return, free of charge, any defective products with direct replacement or with similar products deemed by Atlona to perform substantially the same function as the original products

OR

C) refund the pro-rated value based on the remaining term of the warranty period, not to exceed MSRP, in cases where products are beyond repair and/or no direct or substantially similar replacement products exist.

Repair, replacement or refund of Atlona’s products is the purchaser’s exclusive remedy and Atlona’s liability does not extend to any other damages, incidental, consequential or otherwise.

This Limited Product Warranty extends to the original end-user purchaser of Atlona’s products and is non-transferrable to any subsequent purchaser(s) or owner(s) of these products.

Coverage PeriodsAtlona’s Limited Product Warranty Period begins on the date of purchase by the end-purchaser. The date contained on the end-purchaser‘s sales or delivery receipt is the proof purchase date.

Limited Product Warranty Terms – New Products• 10 years from proof of purchase date for hardware/electronics products purchased on or after June 1, 2013• 3 years from proof of purchase date for hardware/electronics products purchased before June 1, 2013• Lifetime Limited Product Warranty for all cable products

Limited Product Warranty Terms – Refurbished (B-Stock) Products• 3 years from proof of purchase date for all Refurbished (B-Stock) hardware and electronic products purchased on or after June 1, 2013

RemedyAtlona recommends that end-purchasers contact their authorized Atlona dealer or reseller from whom they purchased their products. Atlona can also be contacted directly. Visit www.atlona.com for Atlona’s contact information and hours of operation. Atlona requires that a dated sales or delivery receipt from an authorized dealer, reseller or end-purchaser is provided before Atlona extends its warranty services. Additionally, a return merchandise authorization (RMA) and/or case number, is required to be obtained from Atlona in advance of returns.

Atlona requires that products returned are properly packed, preferably in the original carton, for shipping. Cartons not bearing a return authorization or case number will be refused. Atlona, at its sole discretion, reserves the right to reject any products received without advanced authorization. Authorizations can be requested by calling 1-877-536-3976 (US toll free) or 1-408- 962-0515 (US/international) or via Atlona’s website at www.atlona.com.

ExclusionsThis Limited Product Warranty excludes:

• Damage, deterioration or malfunction caused by any alteration, modification, improper use, neglect, improper packing or shipping (such claims must be presented to the carrier), lightning, power surges, or other acts of nature.• Damage, deterioration or malfunction resulting from the installation or removal of this product from any installation, any unauthorized tampering with this product, any repairs attempted by anyone unauthorized by Atlona to make such repairs, or any other cause which does not relate directly to a defect in materials and/or workmanship of this product.• Equipment enclosures, cables, power supplies, batteries, LCD displays, and any accessories used in conjunction with the product(s).• Products purchased from unauthorized distributors, dealers, resellers, auction websites and similar unauthorized channels of distribution.


Local: 1-408-962-0515

Atlona Product Registration

Thank you for purchasing this Atlona product. - We hope you enjoy it and will take an extra few moments to register your new purchase.

Registration creates an ownership record if your product is lost or stolen and helps ensure you’ll receive notification of performance issues and firmware updates.

At Atlona, we respect and protect your privacy, assuring you that your registration information is completely secure. Atlona product registration is completely voluntary and failure to register will not diminish your limited warranty rights.

To register go to: http://www.atlona.com/registration

DisclaimersThis Limited Product Warranty does not imply that the electronic components contained within Atlona’s products will not become obsolete nor does it imply Atlona products or their electronic components will remain compatible with any other current product, technology or any future products or technologies in which Atlona’s products may be used in conjunction with. Atlona, at its sole discretion, reserves the right not to extend its warranty offering in instances arising outside its normal course of business including, but not limited to, damage inflicted to its products from acts of god.

Limitation on LiabilityThe maximum liability of Atlona under this limited product warranty shall not exceed the original Atlona MSRP for its products. To the maximum extent permitted by law, Atlona is not responsible for the direct, special, incidental or consequential damages resulting from any breach of warranty or condition, or under any other legal theory. Some countries, districts or states do not allow the exclusion or limitation of relief, special, incidental, consequential or indirect damages, or the limitation of liability to specified amounts, so the above limitations or exclusions may not apply to you.

Exclusive RemedyTo the maximum extent permitted by law, this limited product warranty and the remedies set forth above are exclusive and in lieu of all other warranties, remedies and conditions, whether oral or written, express or implied. To the maximum extent permitted by law, Atlona specifically disclaims all implied warranties, including, without limitation, warranties of merchantability and fitness for a particular purpose. If Atlona cannot lawfully disclaim or exclude implied warranties under applicable law, then all implied warranties covering its products including warranties of merchantability and fitness for a particular purpose, shall provide to its products under applicable law. If any product to which this limited warranty applies is a “Consumer Product” under the Magnuson-Moss Warranty Act (15 U.S.C.A. §2301, ET SEQ.) or other applicable law, the foregoing disclaimer of implied warranties shall not apply, and all implied warranties on its products, including warranties of merchantability and fitness for the particular purpose, shall apply as provided under applicable law.

Other ConditionsAtlona’s Limited Product Warranty offering gives legal rights, and other rights may apply and vary from country to country or state to state. This limited warranty is void if (i) the label bearing the serial number of products have been removed or defaced, (ii) products are not purchased from an authorized Atlona dealer or reseller. A comprehensive list of Atlona’s authorized distributors, dealers and resellers can be found at www.atlona.com.

Documents

AT-UHD-SW-52ED - SnapAVatlona.com 5 Toll free: 1-877-536-3976 Local: 1-408-962-0515 HDMI 1 HDMI 2 HDMI 3 HDMI 4 HDMI 5 VOLUME AT-UHD-SW-52ED R IN IR OUT - + + - L FW LAN RS-232 P S