Aquaplus Tech Info 2005 Rev 1 - English

INDEX

PAGE DESCRIPTION

1 Index

2 General Information

3 Materials

4 Section Drawing, Clamped with Pump-out Vanes

5 Section Drawing, Bolted with Pump-out Vanes

6 Section Drawing, Bolted with Wear Rings

7 Section Drawing, Motor Pumps

8 Interchangeability Chart, Unit 25



11 Interchangeability Chart, Unit 55, 60 & 70

12 Limits and Pressures

13 Technical Data

14 Stuffing Box Dimensions

15 Impeller Reduction

16 Pump Dimensions

17 Pump Dimensions

18 Dimensions for Flange, Shaft and Connections

19 Selection Chart, 1450 RPM





PUMP DESIGNATION AND GENERAL DESCRIPTION ____________________

The MTP Aquaplus AP range of pumps fully conforms to DIN 24255 (EN 733) in terms of dimensions and hydraulic performance for single stage end suction pumps.

CASINGS ________________________________________________________________________ All pump casings are cast iron and radially split to allow removal of the rotating element without disturbing the pump casing, suction and discharge piping, driver and coupling alignment. Connections are axial end suction with radial vertical centreline discharge making the casing self venting.

FLANGES ________________________________________________________________________ Standard pump flanges are drilled to BS4504-1969 Table 16/1 (Mating flanges are an optional extra). Gauge tappings are provided on suction and discharge flanges.

IMPELLERS ______________________________________________________________________ The shrouded impellers have front seal rings and either expeller vanes or rear seal rings with balance holes to provide hydraulic balance. Impellers are dynamically balanced and are keyed to the shaft and locked axially between the shaft and impeller nut. The maximum impeller peripheral speed is 40m/sec. for cast iron impellers and 60m/sec. for bronze.

CASING WEAR RINGS _____________________________________________________________ Wear rings are fitted as standard to all casings.

SHAFTS Stainless steel shafts are standard.

SHAFT SLEEVES The "full" stainless steel shaft sleeve which is standard for both the mechanical seal and packed gland version, is of the hook type which allows for expansion along the shaft. It is positively driven by the impeller key.

BEARINGS _______________________________________________________________________ Pumps have two identical single row deep groove ball bearings which are grease lubricated through a grease nipple located in each bearing cover.

MECHANICAL SEAL - STANDARD____________________________________________________ A single mechanical seal, with a ceramic stationary face and carbon rotating face is fitted as standard. The standard seal elastomer is Buna-N with the other seal components being AISI 304 stainless steel. This seal is suitable for applications up to 100 degrees C.

PACKED GLAND OPTIONAL _______________________________________________________ Packed stuffing boxes are available as an option and are fitted with a removable lantern ring with packing over the shaft sleeve to reduce shaft wear.

ROTATION _______________________________________________________________________ Rotation is clockwise when viewed from the drive end.

PERFORMANCE GUARANTEE_______________________________________________________ All Aquaplus DIN 24255 (EN 733) pumps are hydrostatically tested and performance run prior to despatch from our ISO9002 accredited factory.

Materials of Construction

Material Description

Bearings should be lubricated approximately every 1000 operating hours at 3600 rpm, 2000 operating hours at 3000 rpm, 2500 operating hours at 1800 rpm, 4000 operating hours at 1500 rpm with following or

equivalent grease.

SHELL ALVANIA R2 MOBIL MOBILUX 2

AMPOL R R 2 B.P. ENERGREASE LS2

CALTEX MULTIFAX 2

ALL IRON BRONZE FITTED ALL BRONZEALL

STAINLESS STEEL

Casing Cast Iron Cast Iron Bronze Stainless Steel 316

Impeller Cast Iron Bronze Bronze Stainless Steel 316

Impeller Key Stainless Steel 316 Stainless Steel 316

Stainless Steel 316

Stainless Steel 316

Wear Ring Cast Iron Bronze Bronze Stainless Steel 316

Shaft Stainless Steel 420 Stainless Steel

420 Stainless Steel

420 Stainless Steel

316

Shaft Nut Stainless Steel 316Stainless Steel

316Stainless Steel

316Stainless Steel

316

Shaft Sleeve Stainless Steel 316 Stainless Steel

316 Stainless Steel

316 Stainless Steel

316

Lantern Ring Cast Iron Bronze Bronze Stainless Steel 316

Gland Cast Iron Cast Iron Bronze Stainless Steel 316

NEAREST EQUIVALENT STANDARD MATERIAL

AUSTRALIAN BRITISH AMERICAN DIN

BS1452: ASTM A48 DIN 1691 CAST IRON AS1830/T220

GR 220 CLASS 30 GG 20

BS1400 BRONZE AS1565/C95210

Zinc Free Bronze ASTM B30 DIN 1714

AS 1449 BS 970: STAINLESS STEEL GR 420 420/S37

AISI-420 DIN 17440

BS1504 STAINLESS STEEL AS1449 316Ti 316C16

ASTM A743-CF8M

DIN 17445

Pumpout Vanes and Clamped Arrangement

PART NO DESCRIPTION QTY PART NO DESCRIPTION QTY 10-2 Pump Casing 1 46-1 Gland Packing 4 50-2 Case Wear Ring 1 52-4 Shaft Sleeve 1 56-0 Dowel 2 40-01 Sleeve Gasket (when fitted) 1 40-0 Casing Gasket/O Ring 1 90-21 Stud 2 90-3 Drain Plug 1 92-01 Nut 2 41-1 Gasket Ring 1 33-0 Bearing Housing 1 23-0 Impeller 1 36-0 Bearing Cover 2 90-2 Stud 8/12 40-02 Gasket 2 92-0 Nut 8/12 42-1 Oil Seal 2 18-3 Support foot 1 32-1 Bearing 2 90-34 Gauge Plug 1 21-1 Shaft 1 41-14 Gasket Ring 1 94-0 Coupling Key 1 90-11 Hex. Screw 1 94-01 Impeller Key 1 16-1 Casing Cover 1 92-2 Impeller Nut 1 45-8 Lantern Ring 1 50-7 Thrower 1 45-2 Gland 1 90-1 Hex. Screw 6

93-01 Impeller Lock Washer 1

PUMP MODELS

APPLICABLE

32-13 32-16 40-13 40-16 50-13 50-16 65-13 65-16 80-16 80-20 100-16 100-20 125-20 150-20

Pumpout Vanes and Bolted Arrangement

PART NO DESCRIPTION QTY PART NO DESCRIPTION QTY 10-2 Pump Casing 1 52-4 Shaft Sleeve 1 50-2 Case Wear Ring 1 40-01 Sleeve Gasket (when fitted) 1 56-0 Dowel 2 90-22 Stud 8/6 40-0 Casing Gasket/O Ring 1 92-02 Nut 8/6 90-3 Drain Plug 1 90-21 Stud 2 41-1 Gasket Ring 1 92-01 Nut 2 23-0 Impeller 1 33-0 Bearing Housing 1 90-2 Stud 8/12 36-0 Bearing Cover 2 92-0 Nut 8/12 40-02 Gasket 2 18-3 Support Foot 1 42-1 Oil Seal 2 90-34 Gauge Plug 1 32-1 Bearing 2 41-14 Gasket Ring 1 21-1 Shaft 1 90-11 Hex. Screw 1 94-0 Coupling Key 1 16-1 Casing Cover 1 94-01 Impeller Key 1 45-8 Lantern Ring 1 92-2 Impeller Nut 1 45-2 Gland 1 50-7 Thrower 1 46-1 Gland Packing 4 90-1 Hex. Screw 6


PUMP MODELS

APPLICABLE

32-20 32-26 40-20 40-26 50-20 50-26 65-20 65-26 80-26 100-26 125-26

Wear Rings and Bolted Arrangement

PART NO DESCRIPTION QTY PART NO DESCRIPTION QTY 10-2 Pump Casing 1 46-1 Gland Packing 4 50-2 Case Wear Ring 1 52-4 Shaft Sleeve 1 56-0 Dowel 2 40-01 Sleeve Gasket (when fitted) 1 40-0 Casing Gasket/O Ring 1 30-22 Stud 8/6 90-3 Drain Plug 1 92-92 Nut 8/6 41-1 Gasket Ring 1 90-21 Stud 2 23-0 Impeller 1 32-01 Nut 2 90-2 Stud 8/12 33-0 Bearing Housing 1 92-0 Nut 8/12 36-0 Bearing Cover 2 18-3 Support Foot 1 40-02 Gasket 2 90-34 Gauge Plug 1 42-1 Oil Seal 2 41-14 Gasket Ring 1 32-1 Bearing 2 90-11 Hex. Screw 1 21-1 Shaft 1 16-1 Casing Cover 1 94-0 Coupling Key 1 50-21 Back Wear Ring 1 94-01 Impeller Key 1 56-0 Dowel 2 92-2 Impeller Nut 1 45-8 Lantern Ring 1 50-7 Thrower 1 45-2 Gland 1 90-1 Hex. Screw 6


PUMP MODELS

APPLICABLE

40-32 50-32 65-32 80-32 80-40

100-32 100-40 125-32 125-40 125-500 150-26 150-32 150-40 150-500 200-260 200-320 200-400 200-500 250-400 250-500 300-400

Motor Pump Arrangement

PART NO DESCRIPTION QTY PART NO DESCRIPTION QTY

10-2 Pump Casing 1 52-4 Full Shaft Sleeve 1

23-0 Impeller 1 40-0 Casing O Ring 1

16-1 Casing Cover 1 18-30 Motor Support (When Req'd) 1

34 Motor Stool Adaptor 1 90-3 Drain Plug 1

21-M Motor Pump Stub Shaft 1 90-34 Gauge Plug 1

92-2 Impeller Nut 1 93-01 Impeller Lock Washer 1

94-01 Impeller Key 1 83-01 Socket Set Screw 2

43-3 Mechanical Seal 1 94-02 Stub Shaft Drive Key 1

ORDERING SPARE PARTS FOR BS & MP SERIES Please quote complete pump designation and serial number from name plate.

Interchangeable Identity Number for Shaft Unit 25 PUMP SIZE

PARTS DESCRIPTION ITEM NO

QTY PER UNIT

32-1

3

40-1

3

50-1

3

65-1

3

32-1

6

40-1

6

50-1

6

65-1

6

80-1

6

32-2

0

40-2

0

50-2

0

65-2

0

32-2

6

40-2

6

50-2

6

HYDRAULIC ASSEMBLY

PUMP CASING 10-2 1 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16

CASE WEAR RING 50-2 1 1 2 3 4 1 2 3 4 5 2 2 3 4 2 3 4

DOWEL 56-0 2 1 1 1 1 1 1 1 1 2 1 1 1 1 1 1 1

CASING GASKET 40-0 1 1 1 1 1 2 2 2 2 2 3 3 3 3 4 4 4

DRAIN PLUG 90-3 1 2 2 2 2 2 2 2 3 3 2 2 2 3 3 3 3

GASKET RING 41-1 1 2 2 2 2 2 2 2 3 3 2 2 2 3 3 3 3

IMPELLER 23-0 1 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16

8 1 1 1 1 2 2 2 2 2 4 4 4 4 STUD 90-2

12 5 5 5

8 1 1 1 1 2 2 2 2 2 3 3 3 3 NUT 92-0

12 4 4 4

SUPPORT FOOT 18-3 1 1 1 2 3 2 2 3 4 4 3 3 3 3 4 4 4

GAUGE PLUG 90-34 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1

GASKET RING 41-14 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1

HEX SCREW 90-11 1 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4

GAUGE PLUG 90-35 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1

GASKET RING 41-15 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1

CASING COVER ASSEMBLY

CASING COVER 16-1 1 1 1 1 1 2 2 2 2 2 3 3 3 3 4 4 4

LANTERN RING 45-8 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1

GLAND 45-2 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1

GLAND PACKING 46-1 3 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1

SHAFT SLEEVE 52-4 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1

SLEEVE GASKET 40-01 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1

STUD 90-22 8 12 12 12 12 13 13 13

NUT 92-02 8 1 1 1 1 2 2 2

STUD 90-21 2 7 7 7 7 7 7 7 7 7 7 7 7 7 7 7 7

NUT 92-01 2 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6

PLUG 90-33 2 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1

GASKET RING 41-13 2 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1

BEARING HOUSING ASSEMBLY

BEARING HOUSING 33-0 1 1 1 1 1 2 2 2 2 2 1 1 1 1 2 2 2

BEARING COVER 36-0 2 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1

GASKET 40-02 2 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1

OIL SEAL 42-1 2 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1

BEARING 32-1 2 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1

SHAFT 21-1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1

COUPLING KEY 94-0 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1

IMPELLER KEY 94-01 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1

IMPELLER NUT 92-2 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1

THROWER 50-7 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1

HEX SCREW 90-1 6 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1

Interchangeable Identity Number for Shaft Unit 35

PUMP SIZE

PARTS DESCRIPTION

ITEM NO

QTY PER UNIT 80

-20

100-

20

125-

20

150-

20

65-2

6

80-2

6

100-

26

125-

26

40-3

2

40-3

2H

50-3

2

50-3

2H

65-3

2

65-3

2H

80-3

2

80-3

2H

100-

32

HYDRAULIC ASSEMBLY

PUMP CASING 10-2 1 17 18 34 36 19 20 21 22 31 31 32 32 23 23 24 24 25

CASE WEAR RING 50-2 1 5 6 7 10 4 5 6 7 3 3 4 4 5 5 8 8 6

DOWEL 56-0 2 2 2 2 2 1 2 2 2 1 1 1 1 2 2 2 2 2

CASING GASKET 40-0 1 3 3 3 3 4 4 4 4 5 5 5 5 5 5 5 5 5

DRAIN PLUG 90-3 1 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3

GASKET RING 41-1 1 3 3 2 2 3 3 3 3 3 3 3 3 3 3 3 3 3

IMPELLER 23-0 1 17 18 34 36 19 20 21 22 31 31 32 32 23 23 24 24 25

8 6 6 6 6 STUD 90-2

12 5 5 5 5 5 5 5 5 5 5 5 5 5

8 3 3 3 3 NUT 92-0

12 4 4 4 4 4 4 4 4 4 4 4 4 4

SUPPORT FOOT 18-3 1 3 3 5 9 4 4 5 6 4 4 5 5 5 5 6 6 6

GAUGE PLUG 90-34 1 1 1 2 2 1 1 2 2 1 1 1 1 2 2 2 2 2

GASKET RING 41-14 1 1 1 2 2 1 1 2 2 1 1 1 1 2 2 2 2 2

HEX SCREW 90-11 1 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4

GAUGE PLUG 90-35 1 1 1 2 2 1 1 2 2 1 1 1 1 1 1 2 2 2

GASKET RING 41-15 1 1 1 2 2 1 1 2 2 1 1 1 1 1 1 2 2 2

CASING COVER ASSEMBLY CASING COVER 16-1 1 5 5 5 12 6 6 7 7 11 11 11 11 8 8 8 8 8

BACK WEAR RING 50-21 1 10 3 3 4 4 12 12 13 13 14 DOWEL 56-0 2 2 1 1 1 1 1 1 1 1 1 LANTERN RING 45-8 1 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 GLAND 45-2 1 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 GLAND PACKING 46-1 3 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 SHAFT SLEEVE 52-4 1 2 2 2 7 2 2 2 2 2 2 2 2 2 2 2 2 2 SLEEVE GASKET 40-01 1 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 STUD 90-22 8 4 4 4 4 6 6 6 6 7 7 7 7 7 NUT 92-02 8 3 3 3 3 3 3 3 3 3 3 3 3 3 STUD 90-21 2 8 8 8 8 8 8 8 8 9 9 9 9 9 9 9 9 9 NUT 92-01 2 7 7 7 7 7 7 7 7 7 7 7 7 7 7 7 7 7 PLUG 90-33 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 GASKET RING 41-13 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2


BEARING HOUSING 33-0 1 3 3 3 3G 3 3 3 3 3 5 3 5 3 5 3 5 3 BEARING COVER 36-0 2 2 2 2 2 2 2 2 2 2 4 2 4 2 4 2 4 2 GASKET 40-02 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 OIL SEAL 42-1 2 2 2 2 2 2 2 2 2 2 4 2 4 2 4 2 4 2 BEARING 32-1 2 2 2 2 2 2 2 2 2 2 4 2 4 2 4 2 4 2 SHAFT 21-1 1 2 2 2 2G 2 2 2 2 2 2H 2 2H 2 2H 2 2H 2 COUPLING KEY 94-0 1 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 IMPELLER KEY 94-01 1 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 IMPELLER NUT 92-2 1 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 THROWER 50-7 1 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2

HEX SCREW 90-1 6 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2

Interchangeable Identity Number for Shaft Unit 45 PUMP SIZE

PARTS DESCRIPTION

ITEM NO

QTY PER UNIT

150-

26

125-

32

150-

32

80-4

0

100-

40

125-

40

150-

40

HYDRAULIC ASSEMBLY

PUMP CASING 10-2 1 37 26 27 33 28 29 30

CASE WEAR RING 50-2 1 9 7 9 8 6 7 9

DOWEL 56-0 2 2 2 2 2 2 2 2

CASING GASKET 40-0 1 4 5 5 6 6 6 6

DRAIN PLUG 90-3 1 3 3 3 3 3 3 3

GASKET RING 41-1 1 3 3 3 3 3 3 3

IMPELLER 23-0 1 37 26 27 33 28 29 30

STUD 90-2 12 7 8 8 8 8 8 8

NUT 92-0 12 3 4 4 5 5 5 5

SUPPORT FOOT 18-3 1 5 7 7 7 7 8 8

GAUGE PLUG 90-34 1 2 2 2 2 2 2 2

GASKET RING 41-14 1 2 2 2 2 2 2 2

HEX SCREW 90-11 1 4 4 4 4 4 4 4

GAUGE PLUG 90-35 1 2 2 2 2 2 2 2

GASKET RING 41-15 1 2 2 2 2 2 2 2


CASING COVER 16-1 1 13 9 9 10 10 10 10

BACK WEAR RING 50-21 1 9 10 9 11 11 10 9

DOWEL 56-0 2 2 2 2 2 2 2 2

LANTERN RING 45-8 1 3 3 3 3 3 3 3

GLAND 45-2 1 3 3 3 3 3 3 3

GLAND PACKING 46-1 4 3 3 3 3 3 3 3

SHAFT SLEEVE 52-4 1 3 3 3 3 3 3 3

SLEEVE GASKET 40-01 1 3 3 3 3 3 3 3

STUD 90-22 6 15 15 15 15 15 15 15

NUT 92-02 6 9 9 9 9 9 9 9

STUD 90-21 2 10 11 11 11 11 11 11

NUT 92-01 2 7 8 8 8 8 8 8

PLUG 90-33 2 2 2 2 2 2 2 2

GASKET RING 41-13 2 2 2 2 2 2 2 2


BEARING HOUSING 33-0 1 4 4 4 4 4 4 4

BEARING COVER 36-0 2 3 3 3 3 3 3 3

GASKET 40-02 2 3 3 3 3 3 3 3

OIL SEAL 42-1 2 3 3 3 3 3 3 3

BEARING 32-1 2 3 3 3 3 3 3 3

SHAFT 21-1 1 3 3 3 3 3 3 3

COUPLING KEY 94-0 1 3 3 3 3 3 3 3

IMPELLER KEY 94-01 1 3 3 3 3 3 3 3

IMPELLER NUT 92-2 1 3 3 3 3 3 3 3

THROWER 50-7 1 3 3 3 3 3 3 3

HEX SCREW 90-1 6 3 3 3 3 3 3 3

Interchangeable Identity Number for Shaft Units 55, 60 & 70 SHAFT UNIT 55 SHAFT UNIT60 SHAFT UNIT70

PARTS DESCRIPTION

ITEM NO

QTY PER UNIT

200-

320

200-

400

125-

500

150-

500

200-

500

250-

500

300-

400

HYDRAULIC ASSEMBLY

PUMP CASING 10-2 1 41 39 40 38 42 43 44

CASE WEAR RING 50-2 1 12 13 14 15 16 17 18

DOWEL 56-0 2 3 3 3 3 3 3 3

CASING GASKET 40-0 1 8 9 10 10 10 10 9

DRAIN PLUG 90-3 1 4 4 4 4 4 4 4

GASKET RING 41-1 1 4 4 4 4 4 4 4

IMPELLER 23-0 1 41 39 40 38 42 43 44

STUD 90-2 12 9 10 11 11 12 12 13

NUT 92-0 12 6 6 6 6 6 6 6

SUPPORT FOOT 18-3 1 9 9 9 10 11 12 13

GAUGE PLUG 90-34 1 3 3 3 3 3 3 3

GASKET RING 41-14 1 3 3 3 3 3 3 3

HEX SCREW 90-11 1 5 5 5 5 5 5 5

GAUGE PLUG 90-35 1 2 2 2 2 2 2 2

GASKET RING 41-15 1 2 2 2 2 2 2 2


CASING COVER 16-1 1 18 14 15 15 16 16 17

BACK WEAR RING 50-21 1 15 16 17 18 19 20 21

DOWEL 56-0 2 3 3 3 3 3 3 3

LANTERN RING 45-8 1 4 4 5 5 6 6 6

GLAND 45-2 1 4 4 5 5 6 6 6

GLAND PACKING 46-1 4 4 4 5 5 6 6 6

SHAFT SLEEVE 52-4 1 4 4 5 5 6 6 6

SLEEVE GASKET 40-01 1 4 4 5 5 6 6 6

STUD 90-22 6 15 15 15 15 15 15 15

NUT 92-02 6 9 9 9 9 9 9 9

STUD 90-21 2 10 11 11 11 11 11 11

NUT 92-01 2 7 8 8 8 8 8 8

PLUG 90-33 2 2 2 2 2 2 2 2

GASKET RING 41-13 2 2 2 2 2 2 2 2


BEARING HOUSING 33-0 1 6 6 7 7 8 8 8

BEARING COVER 36-0 2 4 4 5 5 6 6 6

GASKET 40-02 2 4 4 5 5 6 6 6

OIL SEAL 42-1 2 4 4 5 5 6 6 6

BEARING 32-1 2 4 4 5 5 6 6 6

SHAFT 21-1 1 5 5 4 4 6 6 6

COUPLING KEY 94-0 1 4 4 5 5 6 6 6

IMPELLER KEY 94-01 1 4 4 5 5 6 6 6

IMPELLER NUT 92-2 1 4 4 5 5 6 6 6

THROWER 50-7 1 4 4 5 5 6 6 6

HEX SCREW 90-1 6 4 4 5 5 6 6 6

HYDROSTATIC TEST PRESSURE MAX. WORKING PRESSURE MAXIMUM UP TO 105C

PUMP MODEL BAR kPa PSI BAR kPa PSI

32-13 24.0 2400 348 16.0 1600 232 32-16 24.0 2400 348 16.0 1600 232 32-20 24.0 2400 348 16.0 1600 232 32-26 24.0 2400 348 16.0 1600 232 40-13 24.0 2400 348 16.0 1600 232 40-16 24.0 2400 348 16.0 1600 232 40-20 24.0 2400 348 16.0 1600 232 40-26 24.0 2400 348 16.0 1600 232 40-32 24.0 2400 348 16.0 1600 232 40-32H 24.0 2400 348 16.0 1600 232 50-13 24.0 2400 348 16.0 1600 232 50-16 24.0 2400 348 16.0 1600 232 50-20 24.0 2400 348 16.0 1600 232 50-26 24.0 2400 348 16.0 1600 232 50-32 24.0 2400 348 16.0 1600 232 50-32H 24.0 2400 348 16.0 1600 232 65-13 24.0 2400 348 16.0 1600 232 65-16 24.0 2400 348 16.0 1600 232 65-20 24.0 2400 348 16.0 1600 232 65-26 24.0 2400 348 16.0 1600 232 65-32 24.0 2400 348 16.0 1600 232 65-32H 24.0 2400 348 16.0 1600 232 80-16 24.0 2400 348 16.0 1600 232 80-20 24.0 2400 348 16.0 1600 232 80-26 24.0 2400 348 16.0 1600 232 80-32 24.0 2400 348 16.0 1600 232 80-32H 24.0 2400 348 16.0 1600 232 80-40 17.2 1720 250 13.0 1300 189 100-20 24.0 2400 348 16.0 1600 232 100-26 24.0 2400 348 16.0 1600 232 100-32 21.3 2130 309 16.0 1600 232 100-40 17.2 1720 250 13.0 1300 189 125-20 24.0 2400 348 16 1600 232 125-26 21.3 2130 309 16.0 1600 232 125-32 21.3 2130 309 16.0 1600 232 125-40 17.2 1720 250 13.0 1300 189

125-500 12.0 1200 174 8.0 800 116 150-20 21.3 2130 309 16.0 1600 232 150-26 16.2 1620 235 10.0 1000 145 150-32 16.2 1620 235 10.0 1000 145 150-40 16.2 1620 235 10.0 1000 145

150-500 12.0 1200 174 8.0 800 116 200-260 6.0 600 87 4.0 400 58 200-320 6.0 600 87 4.0 400 58 200-400 9.0 900 130 6.0 600 87 200-500 16.0 1600 232 10.0 1000 145 250-400 12.0 1200 174 8.0 800 116 250-500 16.0 1600 232 10.0 1000 145 300-400 12.0 1200 174 8.0 800 116

Packed Gland Mech. Seal

MAXIMUM SUCTION PRESSURE 1450 rpm 600 kPa 800 kPa PRESSURE

MAXIMUM SUCTION PRESSURE 2900 rpm 400 kPa 600 kPa

TEMPERATURE -10 to 105C

MAXIMUM SPEED 3600 rpm REFER TO SPECIFIC MODEL FOR EXACT LIMITS

Basic Operating Limits

Maximum Working and Test Pressures

NOMINAL FLANGE SIZE PUMP MODEL

SUCTION DISCHARGE

IMPELLER SEAL RING DIAMETRAL

CLEARANCE (MM)

IMPELLER DIAMETER (MM) BEARING TYPE

(MM) (MM)

MAXIMUM NOMINAL

SPEED DIRECT COUPLED

RPM/IMP. DIA.

MAXIMUM VEE BELT

DRIVE SPEED SG=1 RPM

MAX MIN MAX MIN FRONT REAR

32-13 50 32 3600/134 2900 0.4 0.3 139 100 6305 6305

32-16 50 32 3600/156 2900 0.4 0.3 174 125 6305 6305

32-20 50 32 3600/181 2420 0.4 0.3 214 165 6305 6305

32-26 50 32 3600/264 2650 0.4 0.3 264 205 6305 6305

40-13 65 40 3600/130 2900 0.4 0.3 139 100 6305 6305

40-16 65 40 3600/156 2900 0.4 0.3 174 130 6305 6305

40-20 65 40 3600/186 2900 0.4 0.3 214 165 6305 6305

40-26 65 40 3600/364 2480 0.4 0.3 264 205 6305 6305

40-32 65 40 2300/329 1800 0.4 0.3 329 255 6307 6307

40-32H 65 40 2900/329 2000 0.4 0.3 329 255 3307 3307

50-13 65 50 3600/132 2900 0.4 0.3 139 110 6305 6305

50-16 65 50 3600/159 2900 0.4 0.3 174 130 6305 6305

50-20 65 50 3600/182 2900 0.4 0.3 214 165 6305 6305

50-26 65 50 3600/264 2050 0.4 0.3 264 205 6305 6305

50-32 65 50 2300/329 1800 0.4 0.3 329 255 6307 6307

50-32H 65 50 2900/329 2000 0.4 0.3 329 255 3307 3307

65-13 80 65 3600/134 2900 0.4 0.3 139 120 6305 6305

65-16 80 65 3600/159 2900 0.4 0.3 174 125 6305 6305

65-20 80 65 3600/184 2250 0.4 0.3 214 165 6305 6305

65-26 80 65 3600/264 2180 0.4 0.3 264 205 6307 6307

65-32 80 65 2300/329 1450 0.5 0.4 329 255 6307 6307

65-32H 80 65 2900/329 1450 0.5 0.4 329 255 3307 3307

80-16 100 80 3600/160 2850 0.5 0.4 174 140 6305 6305

80-20 100 80 3600/191 2350 0.5 0.4 214 165 6307 6307

80-26 100 80 3600/264 1940 0.5 0.4 264 205 6307 6307

80-32 100 80 1800/329 1450 0.5 0.4 329 255 6307 6307

80-32H 100 80 2900/329 1600 0.5 0.4 329 255 3307 3307

80-40 100 80 1800/409 1405 0.5 0.4 409 320 6309 6309

100-20 125 100 3600/193 2060 0.5 0.4 214 165 6307 6307

100-26 125 100 3600/255 1620 0.5 0.4 264 205 6307 6307

100-32 125 100 1800/329 1380 0.5 0.4 329 255 6307 6307

100-40 125 100 1500/409 1240 0.5 0.4 409 320 6309 6309

125-20 150 125 3600/193 2060 0.5 0.4 214 165 6307 6307

125-26 150 125 1800/264 1420 0.5 0.4 264 205 6307 6307

125-32 150 125 1800/329 1440 0.5 0.4 329 255 6309 6309

125-40 150 125 1500/409 1060 0.5 0.4 409 320 6309 6309

150-20 200 150 1800/220 1800 0.5 0.4 220 190 6307 6307

150-32 200 150 1800/329 1150 0.5 0.4 329 255 6309 6309

150-40 200 150 1500/409 920 0.5 0.4 409 320 6309 6309

150-500 200 150 1500/500 1500 0.5 0.4 500 400 6411 6411

Pump Technical Data

Stuffing Box Dimensions

PACKING BEARING HOUSING L L1 L2 d dl d2 Lk f 9 SIZE NO. RINGS

25 50 60 47.5 24 32 48 85 M8 35 8 Sq. 35 63 67 63 32 40 60 100 M10 40 10 Sq.

3 PLUS LANTERN RING

45 63 85 55 44 55 75 122 M12 50 10 Sq. 4 PLUS LANTERN RING Dimensions in millimetres

PUMP MODEL PUMP LIQUID CONTENT LITRES MINIMUM FLOW

L/S (WATER AT AMBIENT TEMPERATURE)

BEARING HOUSING ELEMENT WEIGHT

(PUMP LESS CASING) KG

32-13 0.8 0.05 20 32-16 1.0 0.10 25 32-20 1.2 0.20 32 32-26 1.8 0.40 43 40-13 1.1 0.10 21 40-16 1.2 0.15 25 40-20 1.5 0.20 33 40-26 2.1 0.40 44 40-32 2.6 0.70 59 40-32H 2.6 0.70 59 50-13 1.8 0.15 22 50-16 1.8 0.25 25 50-20 2.1 0.30 35 50-26 2.6 0.60 45 50-32 3.1 1.10 56 50-32H 3.1 1.10 56 65-13 2.4 0.20 24 65-16 2.8 0.40 28 65-20 3.1 0.60 35 65-26 3.9 1.00 60 65-32 7.3 2.20 73 65-32H 7.3 2.20 73 80-16 4.0 0.55 31 80-20 4.4 0.80 46 80-26 4.9 1.20 62 80-32 8.3 3.00 74 80-32H 8.3 3.00 74 80-40 9.7 3.00 107 100-20 6.5 1.20 50 100-26 8.0 1.90 66 100-32 9.6 2.40 87 100-40 13.8 2.60 120 125-26 12.0 0.50 67 125-32 14.0 0.55 97 125-40 15.5 0.90 122 150-32 20.0 1.10 101 150-40 24.0 1.30 125

Reducing Impellers For pumps listed, machine only the vanes as shown in drawing below

PUMP SIZE Dm D2a D2i D2 s 135 145 125 145 18.5

80-16 130 140 120 145 18.5 165 170 160 170 9.5

100-20 160 165 155 170 9.5 205 208 203 215 4.50

125-26 200 205 195 215 8.5

Outline and installing dimensions

DIMENSIONS PUMP SIZE

Shaft unit

DNA DNE a f h1 h2 b c e1 m1 m2 n1 n2 s w d I t u y WGT kg

32-13 112 140 190 140 27.5

32-16 132 160

100 35

32-20

80

160 180

50

100

70 240

190 41

32-26

32

50

100 180 225 65

110 125 95 320 250 59

40-13 112 140 210 160 30

40-16

80 132 160

100 240 190 36

40-20 160 180

50

100

70

265 212 44

40-26

25

100

360

180 225 320 250

267

24

50

27

8

61

40-32* 35

40

125 470 200 250

65

110 125

95 345 280 342 32 80 35 10 96

50-13 132 160 100 240 190 34

50-16 180 38

50-20

160 200

50

100

70 265

212

100

46

50-26

25

100

360

180 225

14

320 250

267

24

50

27

8

63

50-32* 35

50

65

125 470 225 280 16 345 280 342 32 80 35 10

140

101

65-13 180 39

65-16

160 200

280

212 43

65-20

25

360

180 225

65

14

125

95

320 250

14

267

24

50

27

8

100

52

65-26

100

200 250 360 280 81

65-32

35

65

80

470 225 280

80

16

160

120 400 315

18

342

32

80

35

10

140

110

80-16 25 360 225 320 250 267 24 50 27 8 100 51

80-20

180 250

65

14

125

95 345 280

14 70

80-26 200 280 91

80-32

35

470

250 315

80

400

315

342

32

80

35

10

120

80-40* 45

80

100

532 280 355 85 440 340 368 42 110 45 12 161

100-16* 35 340 260 81

100-20

125

200 360 280 85

100-26 225

280

106

100-32

35

470

250 315

80

16

160

120

400

315

18

342

32

80

35

10

134

100-40 45

100

125

530 280 355 100 18 200 150 500 400 23 370 42 110 45 12 174

125-20* 35 315 111

125-26 35

470

250

80

16

160

120

400

315

18

342

32

80

35

10 115

125-32 280

355 163

125-40

45

125

150

140

530 315

18

500

400

370

42

110

45

12 181

150-20* 35/1 495 280

400 20 550 450 367 32 80 35 10 140

150-26* 250 355 450 350 164

150-32 280 400 170

150-40

45

160 530

315 450

18

110

370

42

45

12

140

209

150-500 60

150

200

180 375 500 24 140 55 60 16 180 320

200-320 450 315

200-400

55 200

670

355

100

110

200

150

550

450

23

500

48

110

52 14 140

318

200-500 60

200 250

210 785 160 300 240 720 600 535 55 60 16 410

250-400

400

500

150 280 200 650 500 445

250-500

250 240 783

425 545 160 240 720 600

533

516

300-400

70

300

300

280 970 500 600 150

20

190

300

200 800 660

26

670

70

140

74.7 20

180

672

Flange mating dimensions to IS02084 PN16 (DIN2533 PN16, BS4504 PN16) DNA / DNE 32 40 50 65 80 100 125 150 200 250 300

D 140 150 165 185 200 220 250 285 340 395 445

K 100 110 125 145 160 180 210 240 295 355 410

d2X number 17.5 X 4 17.5 X 4 17.5 X 4 17.5 X 4 17.5 X 8 17.5 X 8 17.5 X 8 22 X 8 22 X 12 26 X 12 26 X 12

Dimension `D' shows terminal box on right hand side. this could vary depending on motor brand and size, therefore is for guide only.

LENGTH HEIGHT C/LINE WIDTH PUMP MODEL

MOTOR KW

MOTOR SPEED

IMPELLER DIAM A g C D

32-13 0.55 1440 139 465 252 112 230 2.2 2880 139 543 252 112 253

40-13 0.55 1440 139 465 252 112 235 2.2 2880 112 543 252 112 258 4 2880 139 570 252 112 310

50-13 0.55 1440 123 485 292 132 230

0.75 1440 134 485 292 132 235 4 2880 124 585 292 132 310 5.5 2880 134 690 292 132 368

65-13 1.1 1440 134 538 292 132 263 5.5 2880 130 x 15 690 292 132 310

7.5 2880 131 690 292 132 268

32-16 0.55 1440 174 465 292 132 245

2.2 2880 140 543 292 132 268 4.0 2880 174 615 292 132 368

40-16 1.1 1440 174 518 292 132 278 4 2880 155 565 292 132 310

5.5 2880 174 670 292 132 368

50-16 1.5 1440 174 570 340 160 305 7.5 2880 162 690 340 160 368 11 2880 174 690 340 160 431

65-16 2.2 1440 174 567 360 160 308

11 2880 155 736 360 160 431

15 2880 168 867 360 160 431

80-16 2.2 1440 158 592 405 180 315 3 1440 174 592 405 180 320

15 2880 154 846 405 180 431 22 2880 170 917 405 180 458

32-20 1.1 1440 214 518 340 160 291

4 2880 165 565 340 160 310 7.5 2880 214 670 340 160 368

40-20 1.5 1440 214 538 340 160 291

5.5 2880 165 690 340 160 368 11 2880 214 690 340 160 431

50-20 2.2 1440 214 567 360 160 320 11 2880 185 736 360 160 431 18.5 2880 214 867 360 160 431

65-20 2.2 1440 179 567 405 180 320 4 1440 214 587 405 180 378 15 2880 167 817 405 180 431

22 2880 192 887 405 180 460

LENGTH HEIGHT C/LINE WIDTH PUMP MODEL

MOTOR KW

MOTOR SPEED

IMPELLER DIAM A g C D

80-20 4 1440 195 625 430 180 355 7.5 1440 214 700 430 180 385

18.5 2880 165 906 430 180 440

22 2880 175 931 430 180 450

100-20 4 1440 185 624 480 200 374 7.5 1440 214 700 480 200 396

22 2880 170 x 16 901 480 200 450

32-26 2.2 1440 264 569 405 180 350

15 2880 250 855 405 180 390

40-26 3 1440 264 566 405 180 345

18.5 2880 250 886 405 180 450

50-26 2.2 1440 205 566 405 180 342 4 1440 264 586 405 180 364 22 2880 235 891 405 180 450

65-26 4 1440 205 599 450 200 372 7.5 1440 264 675 450 200 402

80-26 5.5 1440 225 740 480 200 413

11 1440 264 740 480 200 468

100-26 7.5 1440 215 715 505 225 417

15 1440 264 910 505 225 472

125-26 15 1440 255 910 605 250 465 18.5 1440 264 984 605 250 475

40-32 3 1440 285 595 450 200 364

5.5 1440 329 740 450 200 434

50-32 4 1440 255 610 505 225 364 7.5 1440 315 700 505 225 434

65-32 7.5 1440 285 700 505 225 434 11 1440 315 700 505 225 469

80-32 11 1440 280 895 565 250 474 18.5 1440 329 931 565 250 484

100-32 15 1440 300 910 565 250 479

22 1440 329 984 565 250 489

NOTE: Flanges are to DIN 2533 PN 16. All dimensions shown are approximate and subject to change

DIAMETER d BEARINGHOUSING NOM TOL

KEY LENGTH

KEY HEIGHT

KEY WIDTH

SEAT DEPTH

25 24 -0.004 32 7 8 20 +0.009

35 32 -0.002 40 8 10 27 +0.018

45 42 -0.002 55 8 12 37 +0.018

55 48 -0.002 100 9 14 42.5 +0.018

60 55 -0.002 100 11 16 4.1 +0.018

70 70 -0.002 110 14 20 60.7 +0.018

FLANGE RAISED FACE DRILLING* BRANCHSIZE D b d1 f NO. d2 k

BOLTING

32 140 18 78 2 4 18 100 M16 40 150 18 88 3 4 18 110 M16 50 165 20 102 3 4 18 125 M16 65 185 20 122 3 4 18 145 M16 80 200 22 138 3 8 18 160 M16

100 220 24 158 3 8 18 180 M16 125 250 26 188 3 8 18 210 M16 150 285 26 212 3 8 22 240 M20 200 340 30 268 3 12 22 295 M20 250 395 32 320 3 12 26 355 M24 300 445 32 378 4 12 26 410 M24

A B* D DD S

PUMP MODEL

CA

SIN

G

DR

AIN

HO

US

ING

D

RA

IN

GAU

GE

TAPP

ING

VEN

T TA

PPIN

G

GAU

GE

TAPP

ING

32-13 1/4 1/8 1/4 1/4 1/4 32-16 1/4 1/8 1/4 1/4 1/4 32-20 1/4 1/8 1/4 1/4 1/4 32-26 1/8 1/8 1/4 1/4 1/4 40-13 1/4 1/8 1/4 1/4 1/4 40-16 1/4 1/8 1/4 1/4 1/4 40-20 1/4 1/8 1/4 1/4 1/4 40-26 1/8 1/8 1/4 1/4 1/4 40-32 1/8 1/8 1/4 1/4 1/4 50-13 1/4 1/8 1/4 1/4 1/4 50-16 1/8 1/8 1/4 1/4 1/4 50-20 1/4 1/8 1/4 1/4 1/4 50-26 1/8 1/8 1/4 1/4 1/4 50-32 1/8 1/8 1/4 1/4 1/4 65-13 1/4 1/8 1/4 1/4 1/4 65-16 1/8 1/8 1/4 1/4 1/4 65-20 1/8 1/8 1/4 1/4 1/4 65-26 1/8 1/8 1/4 1/4 1/4 65-32 1/8 1/8 1/4 1/4 1/4

A B* D DD S

PUMP MODEL

CA

SIN

G

DR

AIN

HO

US

ING

D

RA

IN

GAU

GE

TAPP

ING

VEN

T TA

PPIN

G

GAU

GE

TAPP

ING

80-16 1/8 1/8 1/4 1/4 1/4 80-20 1/8 1/8 1/4 1/4 1/4 80-26 1/8 1/8 1/4 1/4 1/4 80-32 1/8 1/8 1/8 1/4 1/8 80-40 1/8 1/8 1/8 1/8 1/8 100-20 1/8 1/8 1/8 1/8 1/8 100-26 1/8 1/8 1/8 1/8 1/8 100-32 1/8 1/8 1/2 1/8 1/2 100-40 1/8 1/2 1/2 1/8 1/2 125-26 1/8 1/2 1/2 1/8 1/2 125-32 1/8 1/2 1/2 1/8 1/2 125-40 1/8 1/2 1/2 1/8 1/2 150-32 1/8 1/2 1/2 1/8 1/2 150-40 1/8 1/2 1/2 1/8 1/2

Flange Data

Shaft Dimensions

Service Connections

Note all service connections are BSP female parallel thread

Flange Dimensions and drilling according to ISO 2084 -16BAR (BS4504- 16/11. DIN 2533. ND16)* Holes - Equally spaced straddling pump centreline

Note all service connections are BSP female parallel thread

Service Connections

SELECTION CHART 1450 RPM

Documents

Aquaplus Tech Info 2005 Rev 1 - English