Upload
drifttec101
View
213
Download
0
Embed Size (px)
Citation preview
8122019 AP Peek Cutsheet
httpslidepdfcomreaderfullap-peek-cutsheet 12
9701 PENN AVE S SUITE 107 H BLOOMINGTON MN 55431
18003447499 H FAX 19528816565 H wwwaftonplasticscomINTERNATIONAL ASSOCIATION
DISTRIBUTORSPLASTICSOF
PEEKreg is a high-performance thermoplastic that is manufactured by Victrexreg This material has an extraordinary
combination of mechanical structural and chemical resistant properties
Afton Plastics processes the following grades of PEEKreg 450G (virgin) 450CA30 (carbon ber reinforced) and
450FC30 (bearing grade)
MATERIAL CLASSIFICATIONS
Mil-P 46183 Amendment 2 dated 1 July 1999
Type Imdashnonreinforced plastic
Type III Class 2mdash30 carbon ber reinforced
PRODUCT BENEFITS
Chemical resistance
UL94 V-0 Flammability rating down to 059
Wear resistanceService temperature ndash50 Deg F to +500 Deg F
TYPICAL APPLICATIONS
Thrust washers
Pump gears
Compressor valve plates
KEY MARKETS
Aerospace and Defense
Food Processing
Medical
Oil and Gas
Semiconductor
Automotive and Electrical
Industrial and Nuclear
PEEK reg 991251 POLYARYLETHERKETONE
Hydrolysis resistance
Radiation resistance
FDA compliant
Electrical connectors
Valve seats and seals
Bearings and bushings
8122019 AP Peek Cutsheet
httpslidepdfcomreaderfullap-peek-cutsheet 22
INTERNATIONAL ASSOCIATION
DISTRIBUTORSPLASTICSOF
9701 PENN AVE S SUITE 107 H BLOOMINGTON MN 55431
18003447499 H FAX 19528816565H wwwaftonplasticscomINTERNATIONAL ASSOCIATION
DISTRIBUTORSPLASTICSOF
IAPDMEMBER
GRADE
PROPERTY ASTM
METHOD UNIT 450G 450FC30 450CA30
MECHANICALPHYSICAL
Specic Gravity D-792 132 148 144
Water Absorption 24 hr D-570 05 ndash 006
Tensile Strength 23degC (5 mmmin) BreakYield D-638 psi 14500 (Y) 19000 (B) 32770 (B)
Elongation 23degC (5 mmmin) at Break D-638 50 3 13
Compressive Strength 23degC in ow direction D-695 psi 17110 21750 34800Impact Strength 23degC Notched Izod 001 in radius D-256 ft-lbin 157 169 159
Flexural Modulus 23degC D-790 psi 594500 1175000 2900000
Flexural Strength 23degC D-790 psi 24650 30450 51475
Coefcient of Friction 20degC 1200 inmin 155 lb load ndash 034 011 016
Rockwell Hardness R scale D-785 R 126 ndash 124
THERMAL
Melting Point DSC degC 340 340 340
Heat Distortion Temperature (264 psi) D-648 degC 160 2766 3155
Coefcient of Thermal Expansion (lt 289degF) D-696 10-5degF-1 26 083 083
Continuous Use Temperature degC 250 250 250
Thermal Conductivity C-177 Btu-inhr-ft2-F 175 024 092
Flammability (145 mm thickness) UL 94 V-0 V-0 V-0
ELECTRICAL
Surface Resistivity D-257 ohm-sq ndash ndash ndash
Volume Resistivity D-257 ohm-cm 49 x 1016 ndash 14 x 105
Dielectric Strength (005 mil lm) D-149 KiloVoltscm 190 ndash ndash
Dielectric Constant 23degC 50 Hz-10 kHz D-150 32-33 ndash ndash
Dissipation Factor 23degC 1 MHz D-150 0003 ndash ndash
1 Information provided by Victrex IncH Victrexreg and PEEKtrade are registered trademarks of VictrexNote The data provided in this table are typical for the resins tested and do not represent product specications
VICTREX reg PEEK trade DATA SHEET1
8122019 AP Peek Cutsheet
httpslidepdfcomreaderfullap-peek-cutsheet 22
INTERNATIONAL ASSOCIATION
DISTRIBUTORSPLASTICSOF
9701 PENN AVE S SUITE 107 H BLOOMINGTON MN 55431
18003447499 H FAX 19528816565H wwwaftonplasticscomINTERNATIONAL ASSOCIATION
DISTRIBUTORSPLASTICSOF
IAPDMEMBER
GRADE
PROPERTY ASTM
METHOD UNIT 450G 450FC30 450CA30
MECHANICALPHYSICAL
Specic Gravity D-792 132 148 144
Water Absorption 24 hr D-570 05 ndash 006
Tensile Strength 23degC (5 mmmin) BreakYield D-638 psi 14500 (Y) 19000 (B) 32770 (B)
Elongation 23degC (5 mmmin) at Break D-638 50 3 13
Compressive Strength 23degC in ow direction D-695 psi 17110 21750 34800Impact Strength 23degC Notched Izod 001 in radius D-256 ft-lbin 157 169 159
Flexural Modulus 23degC D-790 psi 594500 1175000 2900000
Flexural Strength 23degC D-790 psi 24650 30450 51475
Coefcient of Friction 20degC 1200 inmin 155 lb load ndash 034 011 016
Rockwell Hardness R scale D-785 R 126 ndash 124
THERMAL
Melting Point DSC degC 340 340 340
Heat Distortion Temperature (264 psi) D-648 degC 160 2766 3155
Coefcient of Thermal Expansion (lt 289degF) D-696 10-5degF-1 26 083 083
Continuous Use Temperature degC 250 250 250
Thermal Conductivity C-177 Btu-inhr-ft2-F 175 024 092
Flammability (145 mm thickness) UL 94 V-0 V-0 V-0
ELECTRICAL
Surface Resistivity D-257 ohm-sq ndash ndash ndash
Volume Resistivity D-257 ohm-cm 49 x 1016 ndash 14 x 105
Dielectric Strength (005 mil lm) D-149 KiloVoltscm 190 ndash ndash
Dielectric Constant 23degC 50 Hz-10 kHz D-150 32-33 ndash ndash
Dissipation Factor 23degC 1 MHz D-150 0003 ndash ndash
1 Information provided by Victrex IncH Victrexreg and PEEKtrade are registered trademarks of VictrexNote The data provided in this table are typical for the resins tested and do not represent product specications
VICTREX reg PEEK trade DATA SHEET1