Upload
jacob-babington
View
220
Download
1
Tags:
Embed Size (px)
Citation preview
An Introduction to Commonly Used Plumbing FittingsA presentationbyDouglas WebleyandDebra Taylor-Croather
The aims of this slideshow are to:
•Introduce the different types of fittings.•Develop an understanding of different types and sizes of fittings.
The objectives of this slideshow are to ensure that students will be able to differentiate between the following types of fittings:
•End feed•Integral solder ring•Speed fit•Hep 2 O•Male & female Iron fittings
And be able to correctly record a Tee fitting.
An Introduction to Common Plumbing Fittings
End Feed Fittings (E/F)
End feed fittings, are fittings where the solder is manually fed in from the end of the fitting during soldering.
All pipes used must be cleaned and have flux applied to each joint before heating with a blow torch and the application of solder
An Introduction to Common Plumbing Fittings
15mm End Feed Coupler 15mm End Feed Tee
Integral Solder Ring (Yorkshire)
Yorkshire fittings (Yorkshire is a trade name) already contain a ring solder inside themAll pipes used must be cleaned and have flux applied to each joint before heating evenly with a blow torch until the solder is seen to melt
An Introduction to Common Plumbing Fittings
15mm Integral Solder Ring Coupler
15mm x 15mm x 15mm Integral Solder Ring Tee
Compression Fittings (COMP)
Compression fittings use a nut and olive (copper,brass or rubber compression ring) to make a water tight seal between the fitting and the pipe. All pipes used must be clean and free from burrs before assembly. A suitable sealing paste should also be applied before the joints are tightened using a wrench or spanner. Do not over tighten as this can lead to problems should the fitting need to be removed
An Introduction to Common Plumbing Fittings
15 millimetre Compression Tee
15 millimetre Compression Service Valve
Speed Fit, HEP2O, Copper/Brass Push Fit
There are many different types of push fit joints are now being marketed, they're available in plastic, brass & copper. There's not much difference between them, they all incorporate some form of grip ring which creates a seal between the pipe and the fitting and prevents the pipe from pulling out. All pipes used must be clean and free from burrs before assembly. Insert the cleaned pipe into the fitting and push into place by hand.
An Introduction to Common Plumbing Fittings
Hep20 Straight Coupler Speed Fit Straight Coupler
Male Iron (MI) Fittings
Male Iron (MI) fittings have an external thread and are made as the name suggests from iron. These fittings are tightened using a wrench or spanner. Always use a suitable sealing compound when assembling joints using these fittings. Do not over tighten.
An Introduction to Common Plumbing Fittings
1/2" MI bsp x15mm Elbow 3/4" MI bsp x 22mm coupler
Female Iron (FI) Fittings
Female Iron (FI) fittings have an internal thread and are made as the name suggests from iron. These fittings are tightened using a wrench or spanner. Always use a suitable sealing compound when assembling joints using these fittings. Do not over tighten.
An Introduction to Common Plumbing Fittings
1/2" FI BSP x 15mm Integral Solder Ring Coupler
1/2" FI BSP x 15mm Compression Elbow
1/2" FI BSP x 15mm Wall Plate Elbow
Fitting Sizes
Fittings are supplied in a variety of sizes ranging from 6mm through to what ever size you require,although larger size fittings may have to be specially ordered.
Generally the average plumber working in domestic properties will come into contact with fittings ranging from 6mm to 28mm.
As a plumber you will continue to come into contact with fittings still measured in old imperial (inches). Some merchants catalogues will have fittings still measured in inches especially internally or externally threaded fittings as these are to BSP (British Standard Pipe).
1/2"=12.7 mm 3/4"=19.05mm 1"=25.4 mm
An Introduction to Common Plumbing Fittings
Ordering Fittings 1
Ordering couplers is straight forward as they are the same size at both ends (eg 15mm coupler) Ordering tees is slightly more complicated. State the largest size first then the opposite side and then the centre size (eg 22mm x 15mm x 22mm or 22mm x 22mm x15mm see examples below)
An Introduction to Common Plumbing Fittings
22mm x 15mm x 22mm Compression Tee
22mm x 22mm x15mm Hep2O Tee
Ordering Fittings 2
What if all the sides of a Tee fitting are the same?
The Tee would simply be called an Equal Tee.
An Introduction to Common Plumbing Fittings
15mm Equal Tee (York) 15mm Equal Tee (Hep2o)
Other Fittings - Tap connectors:
These fittings are also known as swivel fittings and they come in either straights or elbows.
An Introduction to Common Plumbing Fittings
15mm Straight Tap Connector in Brass
15 mm Straight Tap Connector (Speed Fit)
Other Fittings - Tap connectors continued:
Further examples of tap connectors
An Introduction to Common Plumbing Fittings
15 mm Compression Elbow Tap Connector
15 mm Hep2o Elbow Tap Connector
Other Fittings - Reducers
These are used when you need to reduce the pipe size e.g. 22mm cold feed to a bath tap would then be reduced to 15mm to supply a basin tap, not only is this more pleasing to the eye it is also more economical.
An Introduction to Common Plumbing Fittings
Integral Solder Ring Copper Reducer
Push Fit Plastic Reducer
15 mm x 22mm End Feed Reducer
Other Fittings - Stop Ends
These fittings are used for capping off water supplies either temporally or when permanently decommissioning.
An Introduction to Common Plumbing Fittings
22mm Integral Solder Ring Stop End
22mm Compression Stop End
15mm Speed Fit Stop End
Other Fittings - Drain Off
The drain off is a valve located at the lowest point of any system and has a serrated hose connection out-let.
An Introduction to Common Plumbing Fittings
Drain Off (Male Iron) Drain Off (end feed) Drain Off (Hep20 or Speed Fit)
Other Fittings - CouplersCouplers are used to connect pipes together to form longer pipe runs.
An Introduction to Common Plumbing Fittings
15 mm Straight Coupler Compression
15mm End Feed Coupler
15mm Integral Solder Ring Coupler
15mm Speed Fit Coupler
Accurately describe the following fittingsImagine you are ordering these fittings over the phone, what would you ask for?
An Introduction to Common Plumbing Fittings
AcknowledgementsWritten and produced at South Birmingham College
The Centre for the Built Environment
Textual content written by Douglas Welby and Debra Taylor-Croather with additional content by Christopher Poole
E-Learning Content Development Unit
Web Development by Christopher Poole and Roland Douglas
All photographs by Christopher Poole
Distribution
Distributed by the Learning and Skills Development Agency and the National Learning Network as part of Project Q 2005
Important InformationPlease Note
While every attempt has been made to ensure that the contents of this learning object are correct and follow the guidelines as laid down in the Water Regulations Guide second edition South Birmingham College cannot be held responsible for any loss or damage caused by reliance on these materials. All works should carried out by fully qualified persons.