AMMBUSHER HEAVY DUTY BRUSH CUTTER...As an additional safety feature, the PREMIER Ammbusher Heavy Duty Brush Cutter is designed with a front-edge chain curtain. This is provided to

SKID STEER LOADER

AMMBUSHER

HEAVY DUTY

BRUSH CUTTER

MODEL: AC720

OPERATOR’S MANUAL

SERIAL NUMBER: ____________________

WARNING! AVOID INJURY OR DEATH!

READ AND UNDERSTAND THIS ENTIRE MANUAL BEFORE

INSTALLING, OPERATING OR SERVICING THIS EQUIPMENT!

TABLE OF CONTENTS

Letter to the Owner ………………………………………………….... 2

Warranty Policy ………………………………………………….... 3

Warranty Registration Form ………………………………………………….... 4-5

Safety Information ………………………………………………….... 6-7

Hook-Up Procedures ………………………………………………….... 8

To Remove Brush Cutter Attachment ………………………………………………….... 8

Operating Instructions ………………………………………………….... 8

Repair and Maintenance ………………………………………………….... 9-12

Bill of Materials ………………………………………………….... 13

Parts List Diagrams ………………………………………………….... 14-19

Congratulations on the purchase of your

PREMIER Ammbusher Heavy Duty Brush Cutter

You have invested in a quality piece of equipment, backed by people with years of experience.

Your new PREMIER Ammbusher Heavy Duty Brush Cutter is designed and built to cut nearly

all types of brush, grasses, shrubs, and small trees over a variety of terrains. When attached to

a skid loader, it is highly maneuverable for close cutting in tight areas.

Only through proper installation, operation, and maintenance can you expect to receive the

dependable performance and long life for which the attachment was designed. This manual

contains important information regarding the installation, operation, safe use, care and

maintenance of your PREMIER Ammbusher Heavy Duty Brush Cutter. Please be sure that all

operators study this manual carefully and keep it on file for future reference. Don’t forget to

send in your owners registration form.

After reading this manual, if you have any questions about your PREMIER Ammbusher Heavy

Duty Brush Cutter, please contact us immediately as follows:

Toll Free: (866) 458-0008

Local: (260) 456-8518

Fax: (260) 456-6868

Web: www.premierattach.com

E-Mail: [email protected]

Premier strives to provide superior products and the highest level of customer service. If you have

any suggestions on how we can improve for the future, we would appreciate hearing from you.

Thank you for putting your trust in PREMIER.

Premier Attachments, Inc.

2707 Lofty Drive Fort Wayne, IN 46808

2

PREMIER AMMBUSHER

HEAVY DUTY BRUSH CUTTER

WARRANTY POLICY

Model #______________________________ Serial #_______________________________

PREMIER warrants its products to be free from defects in material or workmanship for a warranty period as stated

below. AC720 BRUSH CUTTER: 12 Months

The warranty period begins on the date of purchase by the original purchaser.

Warranty Performance To make a claim under this warranty, contact the dealer purchased from, who will then obtain written return

authorization from PREMIER. All warranty returns must be accompanied by a PREMIER Return Authorization.

Remedy During the applicable warranty period, PREMIER at its option, will repair or replace, free of charge, any product

determined by it to be defective. Such repair or replacement shall take place at a location designated by PREMIER.

Exclusions From Warranty Coverage 1. To qualify for warranty performance the complete unit must be available for PREMIER’s inspection in its

original “failed” condition. 2. There is no warranty against failures caused by or related to alterations or modifications made without

the express written consent of PREMIER. 3. This warranty does not cover damage to the motor and/or gearbox from pressure spikes due to improper

hydraulic system application. 4. This warranty does not cover disassembly of components, i.e., spindles, gearboxes, motors which voids

component warranty. 5. Under no circumstances shall PREMIER be responsible for the cost of labor for field replacement or repair, nor

for damage caused by accident, misapplication, abuse, misuse, operator error, or environmental elements. 6. This warranty does not apply to parts subject to normal wear, such as Blades nor to damage caused by the

failure to perform recommended maintenance or to replace worn parts. 7. Under no circumstances shall PREMIER be obligated for the cost of any repair or replacement by anyone

other than Premier Auger, without its express written consent.

Limitations And Exclusions This warranty is in lieu of all other warranties written or oral, express or implied, statutory or otherwise arising

by operation of law, including any warranty of merchantability or fitness for purpose.

The liability of PREMIER arising out of the supplying of any product covered by this warranty contract, negligence or

otherwise shall not in any case exceed the cost of parts or labor required to rebuild or replace such defective

product, together with the transportation costs attributable thereto. Upon the expiration of the applicable warranty

period herein specified, all such liability shall terminate.

This warranty constitutes the entire warranty of PREMIER, and no oral representations, warranties or guarantees by

any agent of PREMIER or the seller shall be binding on PREMIER, and no part of this warranty may be modified or

extended except upon the express written consent of PREMIER.

Improvements PREMIER continually strives to improve our products. PREMIER reserves the right to make changes or additions to

any product without incurring any obligation whatsoever to make such changes or additions to products previously

sold. 3

Cut

on d

otted lin

e

PREMIER WARRANTY REGISTRATION

DATE PURCHASED_____________________________ MODEL NO.___________________________________ SERIAL#________________________________

OWNER INFORMATION OWNER’S NAME_____________________________________ PHONE___________________________ COMPANY NAME_____________________________________________________________________________ ADDRESS___________________________________________________________________________________ CITY____________________________________________ STATE/PROVIDENCE __________________ ZIP CODE__________________________________ COUNTRY__________________________________

DEALER INFORMATION DEALER SALESMAN________________________________ PHONE__________________________ DEALER NAME _____________________________________________________________________________ ADDRESS___________________________________________________________________________________ CITY____________________________________________ STATE/PROVIDENCE __________________ ZIP CODE__________________________________ COUNTRY__________________________________

INSTALLATION & APPLICATION INFORMATION This PREMIER Ammbusher Heavy Duty Brush Cutter Attachment will be mounted on: SKID STEER MAKE (Brand)_______________________ MODEL_________________________________ APPLICATION_______________________________________________________________________________

This PREMIER Ammbusher Heavy Duty Brush Cutter has been accepted in good condition and I have been

instructed by the dealer to read and understand the entire Operator’s Manual for proper installation, proper and

safe operation, preventative maintenance, service, warranty, and all other information covered in the Operator’s

Manual. I also understand that all operators must read and understand the entire Operator’s Manual.

OWNER’S SIGNATURE_______________________________________ DATE______________________ DEALER’S SIGNATURE_______________________________________ DATE______________________

THIS PAGE MUST BE RETURNED WITHIN 10 DAYS OF PURCHASE TO VALIDATE WARRANTY

MAIL TO: PREMIER

2707 Lofty Drive

Ft. Wayne, IN 46803

#1 - Fold down here

From:

________________________________ Place

________________________________ Postage

Here ________________________________

PREMIER 2707 Lofty Drive Fort Wayne, IN 46808

#2 - Fold up here

#3 - Tape or seal here

SAFETY INFORMATION

TO THE OPERATOR It is the responsibility of all operators to read and understand this entire manual before installing, operating or

servicing the PREMIER Ammbusher Heavy Duty Brush Cutter. Pay particular attention to cautions, warnings and

safe operating procedures. Be a safe and qualified operator. Operate your equipment with care and good judgment

and see to it that it is properly maintained.

SAFETY DECALS WORN, DAMAGED OR ILLEGIBLE SAFETY DECALS MUST BE REPLACED! New safety decals can be ordered

from PREMIER. Safety decals for PREMIER Brush Cutters are ordered and packaged in sets only.

SAFETY INSTRUCTIONS

DISCHARGE DANGER LABEL

The PREMIER Brush Cutters discharge materials out the front. When cutting

with a PREMIER Brush Cutter, never discharge material toward bystanders

nor allow anyone near the machine while in operation. When cutting near bystanders is unavoidable, do not operate the Brush Cutter

without Front Deflector Chains in place, and do not cut in the direction of bystanders.

Bystanders must be at least 75 ft (23 m) away when operating. Clear the work area of objects (fencing, rocks, bottles, wire, etc.) which might be

picked up and thrown.

Always use a shatterproof cab door for your loader or the 3/8” thick safety door when

cutting brush. This is not only to protect you from thrown objects, but primarily to

prevent overhanging or protruding objects such as rebar, tree limbs, or other objects

from entering the cab and causing operator injury. Disengage power to the PREMIER Brush Cutter and shut the loader engine OFF

before leaving the operator’s cab.

Shut the PREMIER Brush Cutter OFF and the loader engine OFF before performing

any inspection or maintenance to the Brush Cutter.

Never place hands or feet under the Brush Cutter deck or near any moving parts when

unit is running. Always keep clear of front discharge area when operating Brush Cutter.

HYDRAULIC LEAK WARNING LABEL

The PREMIER Ammbusher Heavy Duty Brush Cutter has been designed to

reduce the likelihood of hydraulic system leakage. Each Brush Cutter’s

hydraulic system is tested and inspected prior to shipping. However, over

time, any hydraulic system may develop fluid leaks, and very small leaks

may produce high-pressure discharge flows capable of causing injury should

skin come in contact with such discharge.

6

SAFETY INFORMATION (continued)

Do not raise the back of the PREMIER Brush Cutter (nearest operator) over 2 feet off the ground. Never

expose yourself or a bystander to the rotating blades.

When driving the loader to and from the worksite, carry the PREMIER Brush Cutter as low as possible to the

ground to avoid the possibility of tipping forward.

Do not carry passengers on the PREMIER Brush Cutter.

Never leave the PREMIER Brush Cutter unattended in a raised position.

The loader and PREMIER Brush Cutter should be stopped and inspected for damage after striking a foreign

object, and the damage should be repaired before restarting and continuing cutting.

Cut only in daylight or good artificial light.

Keep all nuts, bolts and screws tight, and be sure the equipment is in a safe working condition.

Check the blade mounting bolts for proper tightness at frequent intervals.

When working under the PREMIER Brush Cutter, always securely block it up. If attached to your loader,

visually inspect your lock-on pins to make sure the Brush Cutter is locked onto your loader. Remember, the

PREMIER Ammbusher Heavy Duty Brush Cutter weighs more than 2000 lbs.

Reduce speed on slopes and make turns gradually to prevent tipping or loss of control. Exercise caution

when changing direction on slopes.

Stay alert for drop-offs or holes in the terrain.

Use caution when walking on the Brush Cutter deck. The deck can be slick when wet.

Never drive your skid loader with your PREMIER Brush Cutter raised more than 2 feet. Children are small. Be

aware of their presence and ALWAYS make sure you can see what you are cutting.

7

HOOK-UP PROCEDURES

NOTE: BECAUSE OF THE DIFFERENCES IN ATTACHMENT MOUNTING METHODS AMONG THE VARIOUS

BRANDS OF SKID STEER LOADERS, IT IS IMPORTANT TO CONSULT YOUR SKID STEER OWNERS

MANUAL FOR THE PROPER ATTACHMENT MOUNTING METHOD.

1. Pull up and connect the Brush Cutter to your loader.

2. Secure locking levers. NOTE: Do not attempt to operate attachments with damaged or disengaged lock pins.

3. Connect (2) hydraulic hoses.

TO REMOVE BRUSH CUTTER ATTACHMENT

NOTE: BECAUSE OF THE DIFFERENCES IN ATTACHMENT MOUNTING AND REMOVAL METHODS

AMONG THE VARIOUS BRANDS OF SKID STEERS, IT IS IMPORTANT TO CONSULT YOUR SKID STEER

OWNERS MANUAL FOR THE PROPER ATTACHMENT REMOVAL METHOD.

1. Lower the PREMIER Brush Cutter to ground level.

2. Stop the engine, release hydraulic pressure in hoses and disconnect auxiliary hoses.

3. Release the locking levers and disengage the loader mounting plate.

OPERATING INSTRUCTIONS

The PREMIER Ammbusher Heavy Duty Brush Cutter is capable of cutting trees and vegetation of varying height up

to 7” in diameter. Designed to make your loader more versatile, the PREMIER Ammbusher Heavy Duty Brush

Cutter is intended to perform these functions without the front of the mower deck being raised to a vertical height

greater than 3 feet.

As an additional safety feature, the PREMIER Ammbusher Heavy Duty Brush Cutter is designed with a front-edge

chain curtain. This is provided to reduce the likelihood of discharged objects. Always use a safety door on the

front of your loader to provide the operator an additional level of protection from both overhanging objects (such

as tree limbs) and the potential of discharged objects.

1. Start the Brush Cutter with the loader running slightly above idle. Engage the loader hydraulics and gradually

throttle up to the desired RPM. Maintaining a constant RPM, along with a slower travel speed, will increase your

cutting efficiency.

2. Raise the back of the Brush Cutter (nearest the operator) 4 or 5 inches off the ground. This is necessary for

material to clear from under the cutting deck. Rotate the Brush Cutter front up or down so that the skid rails

are 1 - 2 inches off the ground. The Brush Cutter deck will be sloping front-down (away) from the operator.

This is the optimum method for cutting close to the ground.

Never drive your loader with the Brush Cutter raised more than 2 feet or tilted to the point that your

view is obstructed. Always make sure you can see what you are cutting.

Never operate the Brush Cutter in populated areas, or where thrown objects could injure persons or damage

property. Safety chains MUST be installed.

Never raise the back of the Brush Cutter more than 2 feet off the ground. Never expose yourself or anyone else

to the rotating blades. If you can see the rotating blades when operating the unit, the back of the Brush Cutter

is raised too high. 3. When cutting large brush, operate the PREMIER Ammbusher Heavy Duty Brush Cutter in the following

manner: Slowly drive into the tree and allow the front spring door to open up as you bend the tree with the push

bar. This allows the blades to cut the tree off. The tree can now be mulched by rotating the front up, driving

forward several feet, rolling the front down onto the tree and back-dragging. Keep in mind that, although you

can cut larger trees, the operational life of the attachment may be shortened.

8

REPAIR AND MAINTENANCE

PART “A” BLADE CARRIER REMOVAL

This operation should be performed by an authorized dealer or a qualified technician. The blade carrier

weighs approximately 600 pounds. Should it unexpectedly shift during removal, it could result in

personal injury. An overhead hoist with the appropriate lifting capacity is recommended for this

operation.

1. Set the Brush Cutter flat on the ground. Turn the skid loader engine off to disconnect the hydraulic hoses from the loader. Then, safely disconnect the Brush Cutter from the loader.

2. Attach the hoist to the two lifting points on the push bar.

3. Lift the front of the Brush Cutter, allowing it to lay back upside down, while blocking and bracing the rear

of the Brush Cutter to protect the motor cover and hydraulics.

4. Block the Brush Cutter to ensure that it is stable.

5. Attach the hoist to the blade carrier and apply very light tension. This is a safety precaution to be taken before removing the cap screws.

6. Remove the (8) cap screws and (8) washers that secure the blade carrier to the drive flange, and lift the

blade carrier with the hoist.

PART “B”

BLADE CARRIER INSTALLATION

1. With the Brush Cutter laying upside down and blocked up for stability, attach a hoist to the blade

carrier and lift it into place. Align the holes on the blade carrier to the holes on the drive flange.

2. Reinstall the (8) cap screws and (8) washers, securing the blade carrier to the drive flange. A permanent threadlocker should be applied to the cap screws before installation.

3. Attach the hoist to the lifting points on the push bar.

4. Lift with the hoist to set the Brush Cutter back on the ground in its normal position.

9


PART “C”

REMOVAL AND INSTALLATION PROCEDURE FOR REPLACING OR FLIPPING BLADES


2. Remove the blade service door to expose the access hole in the deck.

3. Lift the front door weldment and secure it with a strap. Then, rotate the blade carrier until the blade-attaching nuts are aligned in the access hole.

4. From the top of the deck, insert a socket through the access hole onto one of the three blade nuts and remove it. Repeat on the other two nuts.

5. Remove the blade and blade hockey puck.

6. Replace, flip or sharpen the blade.

7. Reinstall the blade and blade hockey puck, aligning with the thru holes on the blade carrier.

8. Install the bolts from the bottom-up and tighten the nuts through the access hole on the top of the deck.

9. Repeat the above process on all 3 remaining blades.

NOTE: Only use genuine PREMIER Ammbusher replacement parts. It is recommended to flip all blades at the same time. Blades should be replaced in pairs on opposite sides of the blade carrier to maintain balance. Remember that one pair should always be face-up, with the other face-down.

PART “D” INSTALLING OR REPLACING CARBIDE STUMP GRINDING TEETH 1. Set the Brush Cutter flat on the ground. Turn the skid loader engine off to disconnect the hydraulic hoses from

the loader. Then, safely disconnect the Brush Cutter from the loader.

2. Remove the carbide tooth service door to expose the access hole in the deck.

3. Lift the front door weldment and secure it with a strap. Then, rotate the blade carrier until the tooth

holders are aligned in the access hole of the Brush Cutter deck.

4. From the top of the deck, insert a socket through the access hole onto one of the four carbide tooth nuts and remove. Repeat on the other three nuts and remove the carbide teeth from the blade carrier.

5. From the bottom of the blade carrier, insert the threaded end of a carbide tooth through the holder and secure

it with a lock nut. Note: Make sure that the carbide edge is facing the direction of rotation.

6. Rotate the blade carrier to the next row of carbide teeth and repeat the above steps. There are a total of (4)

rows of teeth. It is recommended that all teeth in all positions be installed in order to help keep the carrier

balanced.

10


PART “E”

MOTOR REMOVAL

1. Set the Brush Cutter flat on the ground. Turn the skid loader engine off to disconnect the hydraulic hoses

from the loader. Then, safely disconnect the Brush Cutter from the loader.

2. Remove the motor cover.

3. Locate the 1/2” hose connected between the motor and the bulkhead fitting. First, disconnect the hose from the bulkhead fitting. Then, disconnect the hose from the motor and remove it. There will be some hydraulic fluid leakage, so have a rag on hand.

4. Locate the 90-degree hoses connected between the manifold and the motor. Lightly loosen the ends of the 90-degree hoses that are connected to the manifold.

5. Lay rags over the ends of the 90-degree hoses connected to the motor’s straight fittings and slowly disconnect them. There will be some hydraulic fluid leakage. Then, remove the straight fittings from the motor.

6. Remove the (4) cap screws and (4) washers holding the motor to the bearing hub.

7. Carefully lift the motor out of the bearing hub. Note the orientation of the motor for future reassembly.

8. To reinstall the new motor, perform the above steps in reverse order. Be sure to apply a permanent threadlocker to the cap screws before tightening.

PART “F” BEARING HUB REMOVAL


2. Remove the blade carrier. Follow the instructions on Blade Carrier Removal in Part “A” of this manual.

3. Remove the motor. Follow the instructions on Motor Removal in Part “E” of this manual.

4. Remove the (8) cap screws and (8) washers holding the bearing hub to the mounting ring on the deck of the

Brush Cutter. Lift the bearing hub off of the mounting ring, using caution not to spill the oil from inside the

bearing hub.

5. To reinstall the bearing hub, perform the above steps in reverse order. Be sure to apply a permanent

threadlocker to the cap screws before installation. After bolting the bearing hub in place, add the

appropriate amount of gear lubricant. Refer to Part “G” of this manual for proper lubrication.

6. Refer to Part “E” and Part “B” of this manual for reinstallation of the motor and blade carrier, respectively.

11


PART “G” CHANGING OIL IN THE BEARING HUB

NOTES:

It is recommended that an oil pump is used for the removal of the old oil from the bearing hub. The proper oil level is approximately 2” from the top of the plug hole on the bearing hub housing. Be

careful not to overfill.


2. Remove one of the plugs on the top of the bearing hub.

3. Insert the oil extraction hose into the bearing hub and remove all of the oil from the bearing hub. Place the

used oil in an appropriate waste oil container for proper disposal.

4. After the used oil has been removed from the bearing hub, refill it to the proper level. The bearing hub oil

capacity is approximately 2.50 US quarts of a GL-5, 80-90W gear lubricant.

5. Reinstall the plug.

PART “H”

REMOVING HYDRAULIC HOSES

Safety Note: There may be pressure in the hydraulic lines. Wear safety glasses and gloves when performing this

operation. 1. Set the Brush Cutter flat on the ground. Turn the skid loader engine off to disconnect the hydraulic hoses from

the loader. Then, safely disconnect the Brush Cutter from the loader.

2. Connect the (2) quick-connect ends of the hoses together. Place the attached quick-connect ends of the hoses

lower than the motor. This will reduce the amount of oil leakage during removal. 3. Lay rags over the hose fittings, then slowly unscrew the hose ends from the straight fittings connected to the

manifold. 4. Drain the hoses into a receptacle for proper disposal of oil.

12

BILL OF MATERIALS

PART # QTY. PART DESCRIPTION 61082 1 AC Hydraulic Pressure Gauge

40005 16 1/2" Crown Lock Flange Nut 61083 1 AC Hyd Gauge Hose, 1/4" NPTF x #4F JIC x 24" Long

40006 4 1/2"-13 x 2” HHCS 61084 1 AC Case Drain Hyd Hose, #6F JIC x #4MB x 29" Long

40015 8 3/8”-18 Top Lock Nut 61085 1 AC Hyd Fitting Long, #16MB x #16M JIC

40035 16 3/4”-10 Top Lock Nut 61126 1 C Series Crossover Relief Manifold Assembly

40055 16 5/16” Split Lock Washer 61253 1 Case Drain Hose

40065 16 3/4"-10 x 3" HHCS, Grade 8 61254 1 Case Drain Plug

40067 8 3/4" Nord-Lock Washer 65025 1 Model 8 Flange Output, AC 1:1, 8T2C1700F5Z

40069 16 5/8"-18 Crown Lock Nut, Grade 8 84339 14 5/16" Chain, 4-Link Length

40070 2 1/4"-20 x 1-1/2" HHCS, Grade 5 84516 4 1/4" Flat Washer, Grade 5

40072 2 1/4" Crown Lock Nut, Grade 5 85161 2 5/16" x 3/4" Self-Tap SC-HWSLTCS

40073 8 3/4"-10 x 3-1/4" HHCS, Grade 8 85267 1 Torsion Spring, Door

40074 8 5/8" Nord-Lock Washer 85371 1 Mini Manual Holder 70111

40075 16 5/16"-18 x 1" HHCS, Grade 5 85493 4 1/2" Nord-Lock Washer

40076 24 5/16" Flat Washer, Grade 5 87517 1 AC/AD Door Chain Bar

40077 4 5/16"-18 Crown Lock Nut, Grade 5 87525 1 AC/AD Door Hinge Pin

40078 8 5/8"-11 x 1-3/4" HHCS, Grade 8 87529 1 AC/AD Carbide Tooth Service Door

40079 4 5/16"-18 x 5" HHCS, Grade 5 87530 1 AC/AD Blade Service Door

40087 4 Cotter Pin, 1/16" x 1-3/8" Long 87533 4 AC Carrier Spacer

40088 6 3/8" x 1-1/4" Carriage Bolt 87534 4 AC Blade Hockey Puck

41004 2 3/8" Flat Washer, Grade 5 87540 4 AC Blade

41028 3 6-32 X 1/2", MMC #93310A148 87542 16 AC Carbide Tooth

45008 8 1/2"-13 x 1-3/4" HHCS, Grade 5 87544 1 AC Manifold Mount Bracket

45011 8 1/2" Flat Washer, Grade 5 87545 1 AC Hyd Bulkhead Bracket

45020 8 1/2" x 1-1/4" Carriage Bolt 87551 13 5/16" Chain, 7-Link Length

60037 1 Hydraulic Motor 6K HD Brush Cutter, 112-1586-006 87579 1 AC/AD Chain Bar Cover, Right

61006 61043

1 Quick Coupler, 1/2" FF Female Quick Coupler, 3/4" FF Female

87580 2 AC/AD Side Chain Bar

61007 61044

1 Quick Coupler, 1/2" FF Male Quick Coupler, 3/4" FF Male

87584 1 AC Runner, Right

61073 1 1" x 12-5/16" Hose, #16 90F JIC x #16 90F JIC 87585 1 AC Runner, Left

61074 1 1" x 12-5/8" Hose, #16 90F JIC x #16 90F JIC 87586 1 AC/AD Chain Bar Cover, Left

61075 2 1" x 96" Hose, #16 90F JIC x #16MB 88116 1 AC/AD Door Weldment

61076 5 AC Straight Fitting, #16MB x #16M JIC 88118 1 AC Lower Carrier Weldment

61077 2 AC Adaptor, #16F x #12MB 88119 1 AC Upper Carrier Weldment

61078 1 AC Bulkhead Fitting, #6M JIC x #6M JIC 88121 1 AC/AD Hood Weldment

61080 1 AC 90 Degree Fitting, #6M JIC x #4MB 88125 2 AC Skid Shoe Weldment

13

PARTS LIST DIAGRAMS

Figure A: Full Assembly

REF. # PART # QTY. PART DESCRIPTION

1 85161 2 5/16" x 3/4" Self-Tap SC-HWSLTCS

2 85371 1 Mini Manual Holder 70111

3 87529 1 AC/AD Carbide Tooth Service Door

4 87530 1 AC/AD Blade Service Door

5 87579 1 AC/AD Chain Bar Cover, Right

6 87585 1 AC Runner, Left

7 87586 1 AC/AD Chain Bar Cover, Left

8 88116 1 AC/AD Door Weldment

9 88121 1 AC Hood Weldment

10 88125 2 AC Skid Shoe

14

Figure B: Blade Carrier


1 40035 16 3/4”-10 Top Lock Nut

2 40065 16 3/4"-10 x 3" HHCS, Grade 8

3 40067 8 3/4" Nord-Lock Washer

4 40069 16 5/8"-18 Crown Lock Nut, Grade 8

5 40073 8 3/4"-10 x 3-1/4" HHCS, Grade 8

6 87533 4 AC Carrier Spacer

7 87534 4 AC Blade Hockey Puck

8 87540 4 AC Blade

9 87542 16 AC Carbide Tooth

10 88118 1 Lower Carrier Weldment

11 88119 1 Upper Carrier Weldment

15

Figure C: Bearing Hub & Motor


1 40006 4 1/2"-13 x 2” HHCS

2 40055 4 5/16” Split Lock Washer


4 40075 4 5/16"-18 x 1" HHCS, Grade 5

5 40076 4 5/16" Flat Washer, Grade 5

6 40078 8 5/8"-11 x 1-3/4" HHCS, Grade 8

7 60037 1 Hydraulic Motor 6K HD Brush Cutter, 112-1586-006

8 61073 1 1" x 12-5/16" Hose, #16 90F JIC x #16 90F JIC

9 61074 1 1" x 12-5/8" Hose, #16 90F JIC x #16 90F JIC

10 61076 2 AC Straight Fitting, #16MB x #16M JIC

11 61084 1 AC Case Drain Hyd Hose, #6F JIC x #4MB x 29" Long

12 65025 1 Model 8 Flange Output, AC 1:1, 8T2C1700F5Z


A B C **Connects to reference lines in Figure D**

16

Figure D: Manifold Assembly & Hose Kit



2 40075 4 5/16"-18 x 1" HHCS, Grade 5


4 40077 4 5/16"-18 Crown Lock Nut, Grade 5

5 40079 4 5/16"-18 x 5" HHCS, Grade 5

6 41028 3 6-32 X 1/2", MMC #93310A148

7 61006 61043

1 Quick Coupler, 1/2" FF Female Quick Coupler, 3/4" FF Female

8 61007 61044

1 Quick Coupler, 1/2" FF Male Quick Coupler, 3/4" FF Male

9 61075 2 1" x 96" Hose, #16 JIC 90F x #16MB

10 61076 3 AC Straight Fitting, #16MB x #16M JIC

11 61077 2 AC Adaptor, #16F x #12MB

12 61078 1 AC Bulkhead Fitting, #6M JIC x #6M JIC

13 61080 1 AC 90 Degree Fitting, #6M JIC x #4MB

14 61082 1 AC Hydraulic Pressure Gauge

15 61083 1 AC Hyd Gauge Hose, 1/4" NPTF x #4F JIC x 24" Long

16 61085 1 AC Hyd Fitting Long, #16MB x #16M JIC

17 61126 1 C Series Crossover Relief Manifold Assembly

18 61253 1 Case Drain Hose

19 61254 1 Case Drain Plug

20 87544 1 AC Manifold Mount Bracket

A B C **Connects to reference lines in Figure C**

17

Figure E: Back Section


1 40015 8 3/8”-18 Top Lock Nut


3 40070 2 1/4"-20 x 1-1/2" HHCS, Grade 5

4 40072 2 1/4" Crown Lock Nut, Grade 5

5 40075 8 5/16"-18 x 1" HHCS, Grade 5


7 40087 4 Cotter Pin, 1/16" x 1-3/8" Long

8 40088 6 3/8" x 1-1/4" Carriage Bolt


10 84339 14 5/16" Chain, 4-Link Length


12 85267 1 Torsion Spring, Door

13 87517 1 AC/AD Door Chain Bar

14 87525 1 AC/AD Door Hinge Pin

15 87529 1 AC/AD Carbide Tooth Service Door

16 87530 1 AC/AD Blade Service Door

17 87551 13 5/16" Chain, 7-Link Length

18 87579 1 AC/AD Chain Bar Cover, Right

19 87580 2 AC/AD Side Chain Bar

20 87586 1 AC/AD Chain Bar Cover, Left

21 88116 1 AC/AD Door Weldment

18

Figure F: Right Side Section


1 40005 8 1/2" Crown Lock Flange Nut

2 45008 4 1/2"-13 x 1-3/4" HHCS, Grade 5


4 45020 4 1/2" x 1-1/4" Carriage Bolt

5 87584 1 AC Runner, Right

6 88125 1 AC Skid Shoe

19

NOTES

Documents

AMMBUSHER HEAVY DUTY BRUSH CUTTER...As an additional safety feature, the PREMIER Ammbusher Heavy Duty Brush Cutter is designed with a front-edge chain curtain. This is provided to