Amhara Water Works Enterprise Compliance

8/22/2019 Amhara Water Works Enterprise Compliance

1/24

I. GENERAL SPECIFICATION REQUIREMENT1. GENERAL REQUIREMENT Statement of Compliance with remarks

1.SERVICE REQUIREMENT

The vehicle to be supplied will be used for road

construction and maintenance projects in Ethiopia where:

Climate varies from humid tropics to arid desert Temperature vary from 00c to 500c. Altitude vary from sea level to 2,100 meters above the

sea level.

The vehicle shall be of extra heavy duty and tropical type

capable enough to render trouble free service under extremely

sever operation condition where grade of fuel is generally used;sand/dust will be thickly blown-up and uneven, bumpy and loose,

gravel road surfaces are predominant.

We offer 4(Four) units of Caterpillar model 770

off-highway trucks, which are extra heavy duty

tropical type, capable enough to render trouble

free services in Ethiopia under the following site

conditions;

Climate varies from humid tropics to ariddesert.

Temperatures vary from 00c to 500c.Altitudes vary from sea level to 3000 meters

above the sea level.

2. Manufacturing Requirement2.1GENERAL

All parts components, accessories &attachments, not specifically mentioned in

these specifications but essential for

dependable and efficient operation of the

vehicle, shall be furnished by the supplier asparts of his bid & shall be accordance with

current engineering and manufacturing

practices and according to prevailing trade

provisions in general and/or as promoters of

safe, effective and efficient function of the

unit.

The vehicle to be supplied shall betropicalized, reliable and dependable for

operation under the conditions specified in

the service requirement.

2.2MATERIALSThe materials of which all parts, attachments,

accessories and components of the unit bid upon

which are manufactured and assembled shall be of


2/24

the current technology durable and reliable for

the intended service. The finish shall be high

quality and good workmanship with dependable

operation.

2.3PE-DELIVERY SERVICE The bidder/supplier shall undertake

inspection and servicing of the unit,

including washing, greasing, lubrication,

adjustment and calibration (if any), to the

buyers satisfaction before commissioning

and final acceptance of the unit at the

final destination.

The bidder/supplier shall bear all costs(parts, materials, labor, etc) of the pre-

delivery service.

3. BASIC INFORMATION The bidder/supplier shall complete a proper

response to each clause/section of the

specification items details with the

necessary relevant comment. This response

shall clarify any variation or non-compliance

with the specification in the event that the

unit bid upon does not fully comply,referring to do these specifications, failure

to do these might

The words comply, satisfy, or yes or similarwords alone may not be adequate response

to the requirement of the specifications

where if is expected to response in figures,

in words or in clear terms shall be provided

with the offer/bid

All documents manuals, charts, drawingsand manufacturers specification literature

included with the bid shall be in English

The foot of each page of this specificationsand nay attached brochures or any other

technical details shall b signed and stamped

by the bidder


3/24

4. COMPLIANCE TO REQUREMENTSBidders/suppliers are expected to offer vehicle

from their product range that closely meets the

technical specification. However, bids which do

not comply with the fundamental requirementsdescribed in the technical specification may be

rejected as non-responsive.

5. ON SITE WARRANTY The bidder/supplier guarantees that all materials,

parts, components, accessories and attachments

that the unit bid upon have been manufactured

and assembled are of high quality and good

workmanship. The bidder/supplier also guarantees

to replace at this cost (DDU cost plustransportation and all labor charges up to the

worksite and or final destination) any part or

component that may break or fail by reason of

inferior or defective material and/or

workmanship within the warranty period.

The warranty period shall be 12 months or50,000km whichever comes first from the date

of formal acceptance.

The bidder/supplier shall undertake to rectifyfaults under warranty upon notification by ARWE

within a maximum of 45 calendar days from dateof notification of such occurrences by the

concerned body of ARWE. Failure to do so will

result in remedial action being undertaken by

ARWE. At the risk and expense of the

bidder/supplier.

ARWE reserves the right to further claim fordown time costs if faults are not rectified within

a specified time above.

Specify extra (additional) warranty period forthe engine and other drives.

6.Proven PerformanceARWE shall consider the previous performance

of the offered make within Ethiopia.

7.After Sales Service Facility


4/24

ARWE shall consider supplier having a well

established dealership and after sales service

facility such as its own well organized

workshop and spare part warehouse in Ethiopia.

8.Recommended Spare Parts List The bidder shall furnish itemized and individually

priced suggested list of recommended spare part

for 80,000km driving mileage.

The suggested list of recommended parts shall becomprehensive enough both in the number of line

items of spare parts and quantity per line item

needed by the vehicle system for the indicatedduration. However, the total list price shall not

exceed 15% of the value of the complete match

machine to be supplied.

9. TrainingTechnical training shall be provided locally at the

expense of the supplier as follows:

In operation of the unit bid to the purchasersemployee at least one operator per unit.

In repair and maintenance of unit bid to thebuyers staff at least five, technical persons.

10. Supply Requirements10.1Manuals

a) 2 operators instruction manualb) 2 diagnostics and workshop repair manualc) 2 spare parts catalogued)

2 maintenance manual

10.2Tools10.1.1 Standard Tools

A set of essential tools which include

appropriate lubrication gun shall be provided

in a lockable toolbox with each unit.


5/24

10.1.2 Special Tools

List of special tools shall be provided with

separate price.

10.3 Fire ExtinguisherOne each multi purpose, proper size fire

extinguisher shall be furnished which each

machine.

10.4 ColorThe vehicle in the supply shall be painted to the

buyers option/choice.

10.5 OptionalItems considered vital by the bidder/supplier for

safe, effective and efficient function of the

vehicle shall be quoted optional as part of the bid.

11. Performance Indicators11.1 Maintenance cost per year (with detail

labor, spare parts, etc)

11.2 Specify certified average fuel consumptionfor the offered vehicle

12. OthersBidder/supplier must provide guaranteed information

as requested hereunder. Failure to do so may be

treated as incomplete and may result in rejection of

their bid as non-responsive.

12.1. Manufacturers recommendation of the change

intervals of lubricant (grease and oils, engine,

hydraulic, transmission final drives gear oils, etc)

considering a 1% sulfur content in the diesel fuel,

working under dusty, sandy and rough terrains


6/24

operating conditions based on 80,000km of driving

mileage.

Lubricant

type

Refill

capacity

(liters)

Change

intervals

in hrs.

or km

Top up

between

change

intervals,

if any

remark

12.2 Manufacturers recommendation of the change

intervals of all filters (air cleaner, engine oil filters,

hydraulic oil transmission oil filters, etc) taking into

account a 1% of sulfur contents in the diesel fuel

working under dusty, sandy and rough terrains

operating conditions based on 80,000km of driving

mileage.

Type of

filter

Unit

price

Quantity

per

machine

Change

intervals

in hr or

km

Remarks

12.3 The spare part held at the agents premises for

the vehicle of offer and the approximate value

with the total number of line items in the stock

for the specific model at the date of bid

submission.

12.4 Maximum parts availability time for the factoryto the local agents premises and/or to the

purchaser by air and sea/ocean freight.

12.5 Details about workshop facilities for after sales

services by faculties including office, parts shop,

repair shops indoor parking places, service in


7/24

operator training, etc.

13. Specification WaiverThe buyer reserves the right to partially or fully

waive compliance to any of these specifications and

make award on the basis that interest of the buyer

is best served.


8/24

II. TECHNICAL REQUIREMENTSSpecification Requirement Statement of Compliance

1.Scope It is the intent of these specifications whether or

not specifically mentioned herein to describe a

heavy duty diesel engine driven, quarry steel body

dump truck.

The truck should be suitable for continuousoperation in tropical conditions specified under

service requirement of Part I general specification

herewith and very rough terrain as well as dusty,

rock and sandy areas.

Maximum gross vehicle weight shall be 75,500kgs Dump body capacity not less than 20m3 when

handling up to 1600kg/m3 material density. The

payload capacity of the track shall be minimum 40

tons.

All items to be fully assembled with the entirenecessary fittings and attachments and tested

ready for immediate use.

Due consideration will be given for bids whichprovided interchanging of parts between models.

2.Engine2.1General

The diesel engine shall perform smoothly and

efficiently under all conditions of operation above

and shall develop the rated horsepower when

operating on commercial diesel fuel with sulfur

content of 1% and cetane number of 50.

2.1.1Engine PerformanceThe engine shall be capable of sustained

operation at about 65km/hr with truck

loaded to its maximum payload capacity

without over loading the engine under

conditions specified in requirement.

2.2TypeThe engine shall be four cycle, water cooled,

diesel, direct injection and turbocharged,


9/24

preferably with after enter cooler, with not less

than six cylinder and shall be equipped with

replaceable cylinder sleeves preferably wet type

liner.

2.3Flywheel Horse PowerThe engine shall deliver minimum 480 BHP min.

SAE J 1349 net at flywheel at rated RPM,

equipped with fuel pump, cooling fan, heavy duty

radiator, lubricating oil pump, air cleaner,

alternator and any other required engine

accessories.

2.4Required Engine DataThe manufacturer shall submit certified engine

data according to SAE standard with his bid

showing net power, torque and specific fuel

consumption curves at governed RPM at sea level

and 2500 elevation.

The supplier shall also furnish certified average

fuel consumption per Km. when the truck is

working under heavy workload.

2.5Lubrication SystemEngine lubrication system shall be of the full

force feed type, by a gear driven oil pump or

equivalent, through oil clarification, by two

replaceable filters (filters through full flow and

by pass cartridge filters or filters of better

filtration system) shall be provided. The engine

oil filler cap permanently attached to filler neck

(oil collar shall incorporate in the lubrication

system.

2.6Starting SystemThe engine shall be equipped with heavy duty 24V

direct electric starting system. An electric motor


10/24

shall start the engine satisfactorily at

temperatures as low as 00C without recourse to

any auxiliary heating or starting device, glow

plugs, or fluid priming system preferably be

reduction type starter motor having about 7kw

rated capacity is required.

2.7Air CleanerHeavy duty of two stage dry type air cleaner

fitted with preferably a cyclone type per cleaner

(automatic dust evacuator and dust indicator)

with restriction gauge/indicator of ample

capacity shall be furnished. The restriction

gauge/indicator shall be well protected from

external damage and strong enough to withstand

shocks and impacts.

3.Fuel System3.1Fuel TankThe fuel tank or tanks shall be properly ventilated,

made from repairable steel, protected both internally

and externally from corrosion and must incorporate a

baffled sump, to collect water formed by a

condensation, properly supported with an underside

sheet metal for protection. Fuel tank(s) made from

plastic will not be accepted. Fuel tank cap shall be

self-closing type permanently fixed on the filler neck

(fuel tank cap should be secured to filler neck by

chain). Tank filler shall contain strainer.

Fuel tank(s) capacity shall be minimum 400 liters.

3.2Injection PumpInjection pump shall be mechanically driven with all

necessary regulatory and controlling attachment.

3.3InjectorsInjectors shall be accessible, interchangeable and


11/24

readily removable.

3.4Fuel FiltersThe fuel filters shall be minimum two in series and

shall be accessible, replaceable and readily removablefor quick maintenance.

3.5Water SeparatorWater separator shall be incorporate in the fuel

filtration system.

4.Cooling SystemThe cooling system shall be of tropicalized closed,

pressurized, pump forced type water medium with

ample capacity to permit continuous full load

operation of the engine without boiling of the coolant

under the conditions specified in the service

requirement herein. The cooling system shall

incorporate an efficient tropicalized thermostat.

4.1RadiatorThe radiator shall be tropicalized of the heavy duty

construction (upper and lower channels/tanks as well

as core shall be made from brass and/or copper of

repairable type) properly mounted to withstand

shocks and strains likely to be encountered in

operation. The radiator shall have adequate capacity

and flow area, plus a compensation for the altitudes

and temperatures in Ethiopia. The radiator shall be

easily removable and cap with strong chain

permanently attached to the radiator shall be

furnished.

The corrosion circuit or equivalent shall be provided

for the purpose of preventing collection of rust and

dust, which gives unfavorable effect on the cooling

line and scale to be collected.


12/24

Plastics will not be acceptable in manfacture of any

part of the radiator except the expansion tank.

It is preferred if possible to install water filter

within the cooling system for trapping foreign

materials.

4.2Cooling FanThe cooling system shall be fitted with and adequate

size direct drive cooling fan made from steel and

driven by belt.

5.Electrical SystemThe electric system shall be composed of but not limited

to a complete 24V electric starting, charging and

lighting systems, electric switches and two keys. All

wiring shall be enclosed in non metallic loom and the

system shall be protected by fuse.

5.1AlternatorThe alternator shall be heavy duty, fan ventilated

with electronic voltage regulator, and shall be of

adequate capacity to provide service under normal

operating conditions. Approximate rated capacity of

alternator shall be 24V/50AMP.

5.2Lighting SystemThe lighting system shall consist of but not limited to:

Two adjustable headlights with high and lowbeam

Two parking lights Two combination stop, tail and direction lights Cabin interior light Backup lights with automatically activated

warning device

Instrument panel light Two reflectors and clearance lights Plate number light


13/24

Fog light and any other light required by I.C.Cmotor vehicle safety regulation

Gravel protection wire mesh grill shall beprovided for all lights installed outside the

cabin.

5.3Directional SignalsThe truck shall be equipped with double faced,

directional signals, prominently mounted at each side

of the vehicle on the front. So that front lamps emit

a flashing signal to both front and rear direction. The

front and rear lens shall be amber colored. The

directional signals shall be of the self canceling type

integrally mounted with steering column. Operation of

the directional lamps shall be indicated to the driver

by indicator light and audible signal on the instrument

panel.

Signal lamps must be activated at once by means of

emergency four way flasher switch, which shall be

installed in the system.

5.4Over Load ProtectionFuses, circuit breakers or equal protection against

damage of short circuits shall adequately protect all

electrical circuit. The circuit protection device shall

be located at a point in the circuit between the power

source and the device being protected.

5.5Windshield WipersThe vehicle, two or three electrically operated wipers

shall be required automatic electric windshield

washers shall be installed.

5.6HornsThe vehicle shall be equipped with two types of horns.

The first type will be electrical with activation by

standard steering wheel button mounted type. The


14/24

second type will be air operated with the horn

mounted at convenient locations.

5.7BatteriesThe batteries shall be heavy duty, of ample power tostart the engine when cold at sufficient speed down

to ambient temperature of 00C. Batteries shall one

12V, 70 AH (minimum) at 20 hours rating.

5.7.1 Battery MountingThe batteries shall be mounted at a convenient place

in a metal box, provided with hold down device and

shall be located so as to provide easy access for

servicing proper cushion shall be provided for battery

seat.

6.Exhaust SystemThe truck should be equipped with heavy duty muffler.

The exhaust pipe shall be preferably vertically located

in such a manner that it will not interfere with the

opening and closing of the cab doors. And the exhaust

pipe shall have adequate insulation and be shielded so as

to prevent burring, charring or damage in any way of the

electrical wiring, fuel supply or other components of the

truck.

7.ClutchThe clutch shall of the heavy duty of adequate size and

plate capacity to assure long life under severe operating

conditions as described under service requirement. The

input torque capacity for the clutch as rated by the

manufacture shall not be less than 10% in excess of that

the maximum net torque developed by the engine.


15/24

8.TransmissionThe transmission shall be heavy duty of

manual/automatic and shall have a minimum of six speed

forward and one reverse speed and shall be a

combination of constant mesh synchromesh typepreferably fully synchromesh in all speeds. The maximum

road speed of the vehicle shall preferably be within the

rant of 50-75 KM/hr.

Final Reduction and Grade ability

The final reduction ratio shall enable the vehicle to

negotiate approximately 50% gradient on road at

altitude of 1000m above sea level in first gear, at

maximum torque and permissible GVW without evidence

of overloading the engine.

9.SteeringThe truck shall be equipped with left hand steering.

Hydraulic power assisted steering system is required. In

event of hydraulic failure, truck shall be safety

controlled by manual effort. Means shall be provided for

easy adjustment of lost motion in the steering gear.

Power steering pump shall be gear drive directly

mounted to the engine.

10. CabThe cab shall be all steel construction with dust, heat

and weather proof windows and clear view windows and

clear view window of toughened glass, with

accommodation for the driver and two passengers.

The cab shall be of all steel welded construction of the

manufacturers standard material, forward control type.

It shall be equipped with heater/defroster, ashtray,

cigar lighter and radio cassette player. Conventional cab

will not be accepted.


16/24

10.1 Instrument panel and controlInstrument panel and control shall include but not

limited to:-

Panel lighting Speedometer with odometer calibrated in

kilometer/hr Tachometer Water temperature gauge/indicator (audible

warning light for engine over heating)

Ammeter or charging indicator light Lighting switches Oil filter element clogging indicator Fuel gauge Air cleaner restriction gauge/indicator Oil pressure gauge with warning signal Cab safety lock hatch indicator Windshield wiper control Engine over running warning device Inter axle lock switch Air pressure gauge/low air pressure warning

signal and other required accessories for

proper and efficient operation of truck.

10.2 SeatsDrivers seat shall be of spring suspension type, cloth

covered with water repellent, and shall be with fore

and after adjustment and CO-drivers seat shall also

be upholstered and cushioned. Seat belts shall be

installed.

10.3 Door LocksBoth doors shall locked from inside and at least one

shall locked from the outside preferably with same

key as used in the staring switch.

10.4 GlassAll glass in the cab for windshields and windows shall

be of the laminated plate type known as safety glass

and shall be free from the imperfections or obvious

distortions.


17/24

10.5 Sun VisorsTwo or three adjustable interior sun visors shall be

installed in the cab in accordance to the

manufacturers practice.

10.6 MirrorsLarge articulated external rear view mirrors shall be

installed on both left and rights hand side of the

vehicle. They shall be properly located as to give the

driver a clear view of the high way though each mirror

for a distance at least sixty meters.

11.FrameThe chassis frame shall be of heavy duty construction

and capable of with standing the strain of rigorous on

and off the road surface and shall provide worth

adequate number of cross members, so designed and

constructed as to support the GVW of the vehicle with

its evenly distributed load. Chassis frame tails shall not

project beyond the rear end of the mounted dump body.

12.Dump Body and Tipping Attachments12.1 CapacityThe dump body shall have a minimum of 20m3 struck

capacity. When handling up to 1600kg/m3 material

density.

12.2 Construction

The dump body shall be constructed of high tensilesteel of if not provide detail specification of body

constructed, material type, by specifying yields point,

tensile strength etc). A minimum thickness of 26mm

floor, 14mm sides and preferably a min. of 16mm

front. The quarry dump truck should be designed for

handling rock or wet sand, wet gravel and clay as well


18/24

as blasted rock and crushed aggregates of basalt and

granite. The dump body shall dump at the rear of the

truck only, with a minimum dumping angle of 50

degrees. The dump body shall have lateral

supports/brackets to prevent twisting off the body

during dumping operations.

12.3 Cab ProtectorDump body shall have reinforced steel cab protector

at least 8mm thickness to extend over the cab. The

cab protector shall be mounted on the dump body by a

full ribbon weld and shall be reinforced.

12.4 HoistThe dump body shall be raised and lowered by one or

two hydraulic hoist of adequate size and strength to

raise, hold and safely lower the fully loaded dump

body under all normal working conditions.

12.5 Hoist ControlsPower take off, pump and valve shall be

manufacturers standard for the hoist model

furnished. Valve and power take off controls shall be

located in the cab. A mechanical safety look shall be

permanently fixed to the body to provide positive

retention in the up position for servicing and repair.

13. Axles and Suspension13.1 AxlesThe truck shall be equipped with heavy duty front and

rear axles. The axle capacity ratings shall be at least

to the gross load imposed at the ground when the

vehicles in evenly loaded to its rated G.V.W.

13.1.1 Front AxleThe front axle shall be manufacturers standard, but

heavy duty construction mounted on heavy duty


19/24

springs with extra heavy duty shock absorbers. All

spindles, kingpins thrust bearings and wheel bearings

shall be properly shall be properly sized and matched

with this axle rating.

13.1.2 Rear AxleThe rear axle shall be of the fully oscillating and full

floating type with hub reduction. The torque input

capacity of this shall exceed the total engine torque

developed through the lowest intervening gear

reduction.

13.2 SuspensionHeavy duty semi elliptical front springs and extra

heavy duty rear springs with adequate number of

leaves to sustain smooth operation of the fully loaded

truck shall be provided.

13.3 Shock AbsorbersManufacturers standard heavy duty double acting,

telescopic shock absorber (if equipped with) of

adequate size and capacity shall be mounted at each

side of the chassis.

14. BumpersManufacturers standard heavy duty steel bumper shall

be installed on the front chassis. The bumper shall span

the complete width of the chassis frame.


20/24

15. Wheel Base15.1 WheelsThe truck shall be equipped with single front and dual

rear, preferably trilex type wheels. All wheels and

rims shall be interchangeable and compatible with thetire size.

15.2 TireTires shall be manufacturers standard but heavy duty

on off highway type, with heavy duty tubes and flaps

shall be provided and shall be mounted on each wheel.

All tires shall be of the same size, type and load

range. A spare tire, tube and wheel shall be furnished

and shall be installed on a strong lockable carrier.

16. Mud GuardsThe tandem wheel base shall be grater than 1300mm.

17. Towing DeviceHeavy duty steel mudguards with rubber flaps, on both

sides of the tandem axle and on the rear size of the

front shall be furnished.

18. Towing DeviceThe vehicle shall be equipped with two towing device

hook ups at front and rear of the chassis mounted with

frame reinforcement as required for proper mounting.

19. Brake SystemThe service brakes shall be capable of controlling and

holding the full loaded truck on a 20% grade and shall be

consistently brining the fully loaded truck to a complete

stop within 12 meters from a speed of 32km/hr on hard,


21/24

dry level road free from loose material.

19.1 Service BrakesService brakes shall be of the all wheel dual system

air type, with rake drums, located at each wheel, and

manually adjusted preferably be S-cam type brake

shoe; brake shall be of the air mechanical type. Brakediaphragm shall be mounted at each wheel in such

manner that no parts of the brake chamber or

diaphragm projects below the axles.

19.2 Parking BrakeThe parking brake shall be preferably hand/hydraulic

or pneumatic/operated mechanical type and capable

of holding the fully loaded truck in an either forward

or reverse on a 20% grade. Parking brakes should be

independent of the service brake. However, it may be

connected to the rear brake shoes through entirely

separated mechanical means.

19.3 Engine BrakeManufacturers standard an air operated engine brake

with an operating switch located within the drivers

reach shall be installed.

19.4 Warning DeviceAn audible and visual low air pressure warning device

shall be installed in the cab of the vehicle. The device

shall activate when the air pressure drops below the

limit specified by the manufacturer.

19.5 Under CoatingThe frame under structure of the truck and under

side of the hood shall be covered with suitable

undercoating to protect the vehicle against corrosion

and rust.


22/24

20. ToolsSet of ordinary and special tools with lubrication fun;

filter wrenches. Wheel nut wrenches 20 tons hydraulic

jack shall be furnished with each machine in tool box.

Tools to supply should be listed.

21. Field Kits of Spare PartsThe following field kits of spare parts are to be

furnished with each machine and price shall be quoted

separately. Parts supplied shall be applicable to the unit

offered.

a) Two each set of all fan belts or other belts employedb) One each set of engine top overhaul gasketsc) One each set of all brake, air or fluid hosesd) Ten each sets of all oil filter elementse) Two each set of all hydraulic ram packing gaskets and

seal

f) One each set of all cooling hosesg) Three each set of all electrical fuses and bulbsh) Ten each set of all air cleaner elementsi) One each set of brake repair kitsj) Two each set of injector nozzles assy (enough for

complete engine)

k) One each set of all shock absorbersl) Two each sets of all brake liningm) One each set of air compressor repair kitsn) One each set of turbo charger repair kits

Please provide unit and total price of each of the items in

the field kits by indicating the description, individual part

number and each set required per each machine (quantity

per machine and total quantity to be supplied) in sequence

of the above.


23/24

22. Essential Accessoriesa) Radiator guardb) Transmission guardc) Two front hooksd) Per cleaner (air)e) Lockable fuel capf) Tire inflation device including connectors charging

hoses reaching to all wheels

g) Inflation pressure gaugeh) One each multi-purpose fire extinguisher located at

easy reach of the operator

i) One each drinking water container with tap havingnot less than 10 liters capacity shall be included in

the supply. Container shall be galvanized

steel/aluminum material/stainless steel.

III. Fundamental Requirements Note that the fundamental requirements of the technical specification are

shown in the table below having the reference number of the technical

specification and corresponding title or sub titles and respective essential

requirements from which the bids should not deviate.

The bid will be determined as substantially responsive only and if only itcomplies with all the fundamental requirements.

Ref.

No.

Description of Parameters Compliance

II. General Requirements

Warranty

5 The warranty period shall be 12 months or 50,000km

whichever comes first from the date of formal

delivery of the machine

7 After sales service facility

Refer Item No. 7 of general specification

requirement

IV.Technical Requirement2 Engine

2.4 Horse Power

The engine shall deliver a minimum of 480 BHP

according to SAE J1349 net at rated RPM


24/24

13 Chassis Frame

Ground Clearance

13.1 The ground clearance shall be a minimum of 500mm

when the vehicle is fully loaded and no other part of

the axle or other components shall protrude below

this clearance.

14 Dump body and tipping attachments

14.1 The dump body shall have a minimum of 20m3 at

struck when handling upto 1600kg/m3 material

density

Documents

Amhara Water Works Enterprise Compliance