Upload
duongkhuong
View
216
Download
3
Embed Size (px)
Citation preview
When it comes to flow...we’re instrumental.4
Inductive Slot Sensor
The alarm mechanism in this flowmeter is an inductive slot sensor. It is a 2-wire, DC, low current device designed to be used with a switch isolator / barrier.
The operating temperature range for this sensor is -13°F to 158°F (-25°C to 70°C).
Note: We can supply the isolator / barrier upon request, but the user must provide the power supply voltage.
DESCRIPTION
Metering Tube 316L SS
Internal Components 316L SS, Hastelloy® C-276
Case and Side Cover Die cast aluminum
Fitting Material / Type 316L SS¼” FNPT, horizontal
Scale Cover 304 SS frame Annealed glass window
O-Ring EPR, Buna N, Kalrez®
PERFORMANCE
Flow Capacities Water 0.6 to 25 GPH (2.4 to 95 LPH)
Air 1 to 120 SCFH (28.3 to 3,400 SLPH)
Accuracy ± 5% of full scale flow
Repeatability 1 %
Turndown 10:1
Ambient Temperature -40°F to 125°F (-40°C to 52°C)
Maximum Temperature O-Ring Maximum Temperature
EPRBuna NViton Kalrez No O-ring
300° F275° F350° F400° F400° F
(149° C)(135° C)(177° C)(204° C)(204° C)
Maximum Pressure Valve models — 1,500 psigNon-valve models — 4,000 psig
OPTIONS
Alarm Single, Inductive Slot Sensor
Certified Calibrations ISA RP 16.6
Control Valves Inlet and outlet
CRNs All Canadian provinces
Rear Mounting Bracket 304 SS
Scales Any volumetric unit
All 316L stainless steel construction makes this meter suitable for low-flow, high-pressure applications.
7100 Series Stainless Steel Tube
ALARM OPTIONS:
7100 with Inductive Slot Sensor
New!Flanged
Connectionand Threaded
Fittings For Easy
Replacement
(714) 891-0008 • www.kinginstrumentco.comWhen it comes to flow...we’re instrumental. 5
DIMENSIONS (INCHES)
ORDERING: Use the following guide to determine the specific product number you require.
7100 Series Specifications Stainless Steel Tube
Order Number
Full Scale Flow WaterGPH
Full Scale Flow Water
LPH
02W .6 2.4
04W 1.2 4.5
06W 2.8 10.5
08W 5.5 20
10W 12 45
12W 25 95
Order Number
Full Scale Flow AirSCFH
Full Scale Flow AirSLPH
00A* 1.0 28.3
01A 2.5 70
03A 5.5 155
05A 13 360
07A 24 680
09A 55 1550
11A 120 3400
* The No O-ring option is for non-valve meters only
7 1 0
Meter Series
Material of Construction
O-ring Material
Scale Valve Options
Optional Alarm
Order Number
Flange Options
316L SS - 1 No O-ring* - 0 Millimeter - 1 Inlet 316L SS - 1 No Alarm - 0 See Spec. 1/2” 150# RF Flange Welded AHST® C-276 - 2 EPR - 1 GPH Water - 2 Outlet 316L SS - 2 With Alarm - A table above 1” 150# RF Flange Welded B
Buna-N - 2 LPH Water - 3 No Valve - 3 1/2” 300# RF Flange Welded CViton® - 3 SCFH Air@STP - 4 Inlet HST® C-276 - 4 1” 300# RF Flange Welded DKalrez® - 4 SLPH Air@STP - 5 Outlet HST® C-276 - 5 1/2” 150# RF Flange Quick Connect E
Non standard - 6 1” 150# RF Flange Quick Connect F1/2” 300# RF Flange Quick Connect G1” 300# RF Flange Quick Connect H
(FULL OPEN)
1
2
10-32 THREADED PANEL MOUNTING HOLES (2 PLACES)
10-32 THREADED HOLE FOR OPTIONAL MOUNTING BRACKET (2 PLACES)
(TYP.)(TYP.)
2
2
1
1
3 OPTIONAL ALARM CONNECTION (BACKSIDE OF CASE)
3
3
4 FLANGE CONNECTION (12" / 3 4" / 1" - 150# FLANGES / QUICK DISCONNECT OPTIONAL)
4
3
OPTIONALQUICKDISCONNECT
OPTIONALQUICKDISCONNECT
* This meter has a titanium float
TOP PLUG
OUTLET FLOAT STOP
FLOAT
METER TUBE
CASE ASSEMBLY
SCREW
Pressure and temperature ratings are based on a study of the engineeringdata for particular materials used in construction and on the design ofindividual models. This information is supplemented by destructive testresults. Meters with stainless enclosures must never be operated withoutshields securely in place. Meters exposed to difficult environments suchas those created by certain chemicals, excessive vibration or other stressinducing factors could fail at or below the suggested maximums. Neveroperate meters above pressure and temperature maximums. It is stronglyrecommended that all meter installations utilize an appropriate pressurerelief valve and/or rupture disc. The pressure settings and locations ofthese devices should be such that meters cannot be over pressurized.Meter failure could result in damage to equipment and serious personalinjury. Always use suitable safety gear, including OSHA approved eyeprotection when working around meters in service. We are happy to passalong chemical compatibility information that has been published by themanufacturer's of raw materials used in our products; however, thisinformation should not be construed as a recommendation made by KingInstrument Company, Inc. for a specific application.
Carefully remove the flowmeter from piping system. Remove the threadedoutlet plug and withdraw the float from the top. All necessary instrumentcomponents are now fully accessible for cleaning with a bottle brush andappropriate mild soap solution*. Before the meter is reassembled, inspectall parts for damage. O-rings should be replaced during metermaintenance and cleaning.To reassemble, carefully guide the magnetic float back into the tube.Reinstall and tighten top plug in appropriate port. Reinstall the instrumentinto the plumbing system after removing the old teflon tape (with a wirebrush) and replacing with fresh teflon tape.*Do not use cleaning agents that will damage float, tube or o-rings.Meters should be cleaned with a mild soap solution. This will be aneffective cleaner of rust stains. Caution must be used so that materials ofconstruction are not damaged by cleaning solutions. Hard water depositscan be removed with 5% acetic acid solution (vinegar).
7100 meters that require repair should be sent to the factory. Please callfor a Return Merchandise Authorization (RMA) number and returninstructions.
-O-rings should be replaced if meter is disassembled after it has been inservice.-Serious property damage and great personal injury could occur as theresult of a meter misused or used in an unsuitable application.
1) Inspect meter for damage that may have occurred during shipping. Reportany damage to the container to the freight carrier immediately.
This is important information. Read it carefully beforebeginning work.
2) Make sure your pressure, temperature, fluid and other requirements arecompatible with the meter including o-rings (where applicable).3) Select a suitable location for installation to prevent excess stress on themeter which may result from:
a) Misaligned pipe.b) The weight of related plumbing.c) "Water Hammer" which is most likely to occur when flow is suddenlystopped as with quick closing solenoid operated valves. (If necessary, asurge chamber should be installed. This will also be useful in pressurestart-up situations.)d) Thermal expansion of liquid in a stagnated or valve isolated system.e) Instantaneous pressurization which will stress the meter and could resultin tube failure.
NOTE: In closed thermal transfer or cooling systems, install the meter in thecool side of the line to minimize meter expansion and contraction and possiblefluid leaks at the threaded connections.4) Handle the meter carefully during installation.
a) Use an appropriate amount of teflon tape on external pipe threads beforemaking connections. Do not use paste or stick type thread sealing products.
5) Install the meter vertically with the inlet port at the bottom.6) Meters with stainless steel fittings will support several feet of pipe as longas significant vibration or stress resulting from misaligned pipe are not factors.
EPR 225 °FBuna-N
VitonKalrez
275 °F350 °F400 °F
Non-valveInlet / Outlet Valve
4,000 psig1,500 psig
Maximum Non-ShockPressure andTemperature O-Ring Temperature
Ambienttemperature
-40° F - 125° F
Viton and Kalrez are registered trademarks of DuPont Dow Elastomers.
O-Ring Material MaximumTemperature
ADDITIONALLY:-7100 Series meters are designed for vertical installation only. (Inlet at bottom,Outlet at top)-Do not remove or adjust the screws on the side of the indicator housing.These screws were positioned during factory calibration and represent thezero adjustment. If these screws are loosened and the indicator housing ismoved, the scale will be out of accuracy.Caution: Zero is factory set when meter is calibrated.DO NOT loosen screws that fasten indicator housing tometer body. If indicator housing is moved, the meterwill need to be calibrated.
2X
REAR CASE SCREW PLUG
SCALE PLATE
POINTER ASSEMBLY
POINTER ASSEMBLY
CASE COVER GASKET
CASE COVER
CASE COVER
2X
4X
FOLLOWER DISC/
METER TUBE ASSEMBLY
SCREW
SCREW
TOP PLUG
OUTLET FLOAT STOP
FLOAT
METER TUBE
CASE ASSEMBLY
ASSEMBLY SCREW
REAR CASE
METER TUBE
SCALE PLATE
POINTER ASSEMBLYPOINTER ASSEMBLY
CASE COVER
CASE COVER
CASE COVER
FOLLOWER DISC/
SCREW
SCREW
VALVE O-RING
VALVE ASSEMBLY
2X
2X
2X
4X
ASSEMBLYMETER TUBEFLANGE ASSEMBLY
SCREW PLUG
ASSEMBLYMETER TUBEFLANGE ASSEMBLY
GASKET
Maximum Non-ShockPressure andTemperature
300#psig
150#psig
Temp.°F
600225200540200300515180400
Ambienttemperature
-40° F - 125° F
EPR 225 °FBuna-N
VitonKalrez
275 °F350 °F400 °F
O-Ring TemperatureO-Ring Material Maximum
Temperature
Viton and Kalrez are registered trademarks of DuPont Dow Elastomers.
FNPT CONNECTION
FLANGED CONNECTION
1.813
5.475
4.000
.470
1.021.470
1.5004.505
.330
.330 1.400
.8101.625
2.180
1.900
10-32 THREADED HOLE FOR INSTALLING
(FULLY OPEN)
10-32 THREADED PANEL MOUNTING HOLES (2 PLACES)
THE OPTIONAL BACK MOUNTING BRACKET (2 PLACES)
(FULL OPEN)
1
2
10-32 THREADED PANEL MOUNTING HOLES (2 PLACES)
10-32 THREADED HOLE FOR OPTIONAL MOUNTING BRACKET (2 PLACES)
(TYP.)(TYP.)
2
2
1
1
3 OPTIONAL ALARM CONNECTION (BACKSIDE OF CASE)
3
3
4 FLANGE CONNECTION (12" / 3 4" / 1" - 150# FLANGES / QUICK DISCONNECT OPTIONAL)
4
3
OPTIONALQUICKDISCONNECT
OPTIONALQUICKDISCONNECT
1.840
4.040