AirPrime MC Series Dev Kit Quick Start Guide

AirPrime MC Series Dev Kit

Quick Start Guide

2130705Rev 1.5

Preface

Important Notice

Due to the nature of wireless communications, transmission and reception of data can never be guaranteed. Data may be delayed, corrupted (i.e., have errors) or be totally lost. Although significant delays or losses of data are rare when wireless devices such as the Sierra Wireless modem are used in a normal manner with a well-constructed network, the Sierra Wireless modem should not be used in situations where failure to transmit or receive data could result in damage of any kind to the user or any other party, including but not limited to personal injury, death, or loss of property. Sierra Wireless accepts no responsibility for damages of any kind resulting from delays or errors in data transmitted or received using the Sierra Wireless modem, or for failure of the Sierra Wireless modem to transmit or receive such data.

Safety and Hazards

Do not operate the Sierra Wireless modem in areas where blasting is in progress, where explosive atmospheres may be present, near medical equipment, near life support equipment, or any equipment which may be susceptible to any form of radio interference. In such areas, the Sierra Wireless modem MUST BE POWERED OFF. The Sierra Wireless modem can transmit signals that could interfere with this equipment.

Do not operate the Sierra Wireless modem in any aircraft, whether the aircraft is on the ground or in flight. In aircraft, the Sierra Wireless modem MUST BE POWERED OFF. When operating, the Sierra Wireless modem can transmit signals that could interfere with various onboard systems.

Note: Some airlines may permit the use of cellular phones while the aircraft is on the ground and the door is open. Sierra Wireless modems may be used at this time.

The driver or operator of any vehicle should not operate the Sierra Wireless modem while in control of a vehicle. Doing so will detract from the driver or operator's control and operation of that vehicle. In some states and provinces, operating such communications devices while in control of a vehicle is an offence.

Limitation of Liability

The information in this manual is subject to change without notice and does not represent a commitment on the part of Sierra Wireless. SIERRA WIRELESS AND ITS AFFILIATES SPECIFICALLY DISCLAIM LIABILITY FOR ANY AND ALL DIRECT, INDIRECT, SPECIAL, GENERAL, INCIDENTAL, CONSEQUENTIAL, PUNITIVE OR EXEMPLARY DAMAGES INCLUDING, BUT NOT LIMITED TO, LOSS OF PROFITS OR REVENUE OR ANTICIPATED PROFITS OR REVENUE ARISING OUT OF THE USE OR INABILITY TO USE ANY SIERRA WIRELESS PRODUCT, EVEN IF SIERRA WIRELESS AND/OR ITS AFFILIATES HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES OR THEY ARE FORESEEABLE OR FOR CLAIMS BY ANY THIRD PARTY.

Notwithstanding the foregoing, in no event shall Sierra Wireless and/or its affiliates aggregate liability arising under or in connection with the Sierra Wireless product, regardless of the number of events, occurrences, or claims giving rise to liability, be in excess of the price paid by the purchaser for the Sierra Wireless product.

Rev 1.5 Apr.10 Proprietary and Confidential 3

AirPrime MC Series Dev Kit Quick Start Guide

Patents Portions of this product may be covered by some or all of the following US patents:5,515,013 5,629,960 5,845,216 5,847,553 5,878,234 5,890,0575,929,815 6,169,884 6,191,741 6,199,168 6,339,405 6,359,5916,400,336 6,516,204 6,561,851 6,643,501 6,653,979 6,697,0306,785,830 6,845,249 6,847,830 6,876,697 6,879,585 6,886,0496,968,171 6,985,757 7,023,878 7,053,843 7,106,569 7,145,2677,200,512 7,295,171 7, 287,162 D442,170 D459,303 D599,256D560,911

and other patents pending.

This product includes technology licensed from QUALCOMM® 3G.

Manufactured or sold by Sierra Wireless or its licensees under one or more patents licensed from InterDigital Group.

Copyright ©2010 Sierra Wireless. All rights reserved.

Trademarks AirCard® and Watcher® are registered trademarks of Sierra Wireless. Sierra Wireless™, AirPrime™, AirLink™, AirVantage™ and the Sierra Wireless logo are trademarks of Sierra Wireless.

Windows® and Windows Vista® are registered trademarks of Microsoft Corporation.

Macintosh and Mac OS are registered trademarks of Apple Inc., registered in the U.S. and other countries.

QUALCOMM® is a registered trademark of QUALCOMM Incorporated. Used under license.

Other trademarks are the property of their respective owners.

Contact Information

Consult our website for up-to-date product descriptions, documentation, application notes, firmware upgrades, troubleshooting tips, and press releases:

www.sierrawireless.com

Sales Desk: Phone: 1-604-232-1488

Hours: 8:00 AM to 5:00 PM Pacific Time

E-mail: [email protected]

Post: Sierra Wireless13811 Wireless WayRichmond, BCCanada V6V 3A4

Fax: 1-604-231-1109

Web: www.sierrawireless.com

4 Proprietary and Confidential 2130705

mailto:[email protected]

http://sierrawireless.com

http://sierrawireless.com

Preface

Revision History

Revision number

Release date Changes

1.2 Feb 2009 Newest UDK board; revised software installation procedure

1.3 Mar 2009 Added MC5728V.Added a column for MC5727V to Table 2-6 on page 22.Removed references to MC5720, MC5725/MC5725V.Removed QUALCOMM patents from preface.

1.4 Jul 2009 Added MC8700.Removed references to MC8755, MC8755V, MC8765V, MC8785V.Updated Table 2-6, Dev Kit—Module signal map, on page 22

1.5 Apr 2010 Added MC8201 and MC8795V.New template/branding.





Contents

Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9

Required equipment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Setup and Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13

Hardware setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Insert a SIM card (UMTS Mini Cards only) . . . . . . . . . . . . . . . . . . . . . . .13

Insert the Mini Card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15

Connect the antenna(s) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16

Connect the power supply and USB cable . . . . . . . . . . . . . . . . . . . . . . .17

Remove/replace the Mini Card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17

Connect the Dev Kit and host device using a Mini Card Host Extender .17

Configure the Mini Card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

Install / update Mini Card drivers and Watcher . . . . . . . . . . . . . . . . . . . . . . 22

Download CDMA installer package . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22

Download UMTS installer package . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23

Install CDMA or UMTS software . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23

Schematic diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25

Bill of Materials . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27



Rev 1.5 A

1
1: IntroductionThis quick start guide explains how to set up the hardware and software components of Sierra Wireless’ PCI Express Mini Card Dev Kit for use with the modules listed in Table 1-1.
The Dev Kit will also be used for forthcoming CDMA and UMTS Mini Card modules. (Older Mini Cards may also be supported.)

Table 1-1: Supported AirPrime Mini Cardsa

a. Throughout this document, MC57xx and MC8xxx refer to the listed suites of CDMA and UMTS Mini Cards respec-tively.

Network Mini Cards

CDMA (MC57xx) MC5727MC5727VMC5728V

UMTS (MC8xxx) MC8201MC8700MC8775MC8775VMC8780MC8781MC8790MC8790VMC8791VMC8792VMC8795V

pr.10 Proprietary and Confidential 9


Required equipment

Table 1-2 details the items required to begin using the Dev Kit in your development environment. If any items are missing from the Dev Kit, contact your Sierra Wireless representative.

Table 1-2: Required equipment

Item Included in Dev Kit

Details

Drivers & Watcher software

No Watcher software and Mini Card device drivers for the following operatirng systems may be downloaded from www.sierrawireless.com/minicard:

• Windows XP Pro (SP3) and higher

• Windows Vista (SP1) and higherRegistration is required to download these and other files.

Mini Card No The Dev Kit supports the Mini Cards listed in Table 1-1 on page 9 (purchased separately).

Antenna kit Yes The antenna kit includes 2 each of:

• Antenna

• Antenna connector

• Sample / replacement Molex connector

• Connecting wire

Audio headset Yes

Antenna connector

removal tool

Yes

PCI Express Mini Card Dev Kit

Yes The Mini Card is inserted into the Dev Kit for testing and development.


http://www.sierrawireless.com/minicard

Introduction

Power supply Yes Universal power supply, suitable for both 120 V and 240 V

UART cable Yes D-sub9 (male) to D-sub9 (female)

USB cable Yes Standard USB-A to USB-B cable

SIM/USIM card No (UMTS only) You need to supply a SIM/USIM with an active account for use with UMTS Mini Cards.

Flat flex cable Yes Together, these are used to connect a Mini Card to a laptop via the Dev Kit.

Mini Card host extender

Yes

Table 1-2: Required equipment (Continued)

Item Included in Dev Kit

Details




Rev 1.5 A

2
2: Setup and InstallationTo begin using the Dev Kit with your development system, set up your hardware and software:
• Hardware setup· Insert a SIM card (UMTS Mini Cards only) on page 13· Insert the Mini Card on page 15· Connect the antenna(s) on page 16· Connect the power supply and USB cable on page 17· Connect the Dev Kit and host device using a Mini Card Host

Extender on page 17

• Software setup (CDMA)· Install / update Mini Card drivers and Watcher on page 22

Hardware setup

Insert a SIM card (UMTS Mini Cards only)

Note: Throughout this document, ‘SIM’ refers to ‘SIM’ and ‘USIM’.

To use a UMTS Mini Card (MC8xxx), you need to install:

• A live SIM card (with an active account), or

• A test SIM card for use with a call box (for example, an Agilent 8960 or Rohde&Schwarz CMU200)

To install the SIM card:

1. Place the Dev Kit face-up (as shown)—the SIM slot is on the left side beside the USB plug and the black banana plug.

Figure 2-1: SIM slot location



2. Open the SIM casing—push the SIM slot cover into the ‘OPEN’ position (in the direction of the ANALOG HEADER), and then lift it.

Figure 2-2: Opening the SIM cover

3. Insert the SIM card into the cover with its circuitry face-down—note the location of the notched corner of the card in the following image.

Figure 2-3: Inserting a SIM into the open cover

4. Lower the SIM slot cover—the cover (with the card inside) will be slightly raised (not making contact with the board).

5. Gently press down on the cover and then slide the slot cover under the connector base latches into the ‘CLOSED’ position—the cover locks into place.

Figure 2-4: SIM inserted with cover closed


Setup and Installation

Insert the Mini Card

After inserting the SIM card, insert the Mini Card:

1. Place the Dev Kit face-up (as shown)—the Mini Card slot is in the top right corner.

Figure 2-5: Mini Card slot

2. Hold the Mini Card at the screw holes and slide it into the Dev Kit’s Mini Card slot at a 45 angle (inserting it ‘flat’ may damage the module’s contacts and wear out the host connector).

Figure 2-6: Inserting a Mini Card

3. Push the free end of the Mini Card down until it clicks into the black MINIPCI-E latch.

Figure 2-7: Locking a Mini Card into the Dev Kit



Connect the antenna(s)

After installing the Mini Card, connect the supplied antenna(s) to the Dev Kit (some Mini Cards include both a main and an auxiliary (diversity/gps) antenna):

1. Place the Dev Kit face-up. The antenna connectors are on the right side near the top.

2. Screw the silver adapter onto the Dev Kit’s main antenna connector.

Figure 2-8: Connecting the antenna adapter

3. Connect the Mini Card’s main antenna to the Dev Kit’s main antenna connector using the gray wire provided—press down lightly on the connector ends. (The first few times you use these connectors, they may be quite snug—press straight down on the end to get a secure connection.)

Figure 2-9: Connecting the antenna wire

4. Connect the antenna to the adapter. (The first few times you attach the antenna, it may be quite snug.)

Figure 2-10: Connecting the antenna

5. If your Mini Card supports a second antenna (diversity or gps), repeat Step 2–Step 4 for the second antenna.



Connect the power supply and USB cable

To install the power supply and USB cable:

1. Place the Dev Kit face-up.

2. Insert one end of the USB cable into the USB connector (beside the SIM slot)—you will connect the other end to your development computer later (DO NOT connect it yet).

3. Insert the power supply into the Dev Kit’s power supply connector (below the red banana plug, to the left of the UART1 connector)—the other end connects to a standard power outlet.

Remove/replace the Mini Card

When you want to remove or replace the Mini Card:

1. Place the Dev Kit face-up.

2. Remove the connecting wire(s) from the Mini Card’s antenna(s)—use the connector tool, hook it under the RF connector and pull straight up.

Figure 2-11: Removing the antenna wire

3. Holding the Dev Kit firmly in place, pull both arms of the MINIPCI-E latch at the same time toward the antenna connectors to release the module.

4. Pull the Mini Card out of the slot at a 45 angle.

Connect the Dev Kit and host device using a Mini Card Host Extender

To test the Mini Card integrated with the host device, use the Mini Card Host Extender and flat flex cable to connect the Dev Kit board and the host device:

1. Prepare the Dev Kit as normal—insert the SIM (for UMTS modems), insert the Mini Card, and attach the antenna. (You can do these steps at any time in this procedure.)

2. Insert the Mini Card Host Extender in your host device in the same way that you would insert the actual Mini Card.

Note: For simplicity, the images in this example show the Mini Card Host Extender unattached.



3. Insert one end of the flat flex cable (pins facing up) into any of the three connectors on the Mini Card Host Extender:

a. Push the cable forward, between the tabs of the brown clip on the connector. As you move the cable forward, you will feel some slight resis-tance as it moves into the connector and the clip tilts slightly upward.

Figure 2-12: Attaching a host extender to a Mini Card

b. When the cable is seated firmly in the connector, push down on the arms of the brown clip to lock the connector in place.

4. Insert the other end of the flat flex cable into connector CN9 on the Dev Kit board using the same method.

Figure 2-13: Attaching a host extender to the Dev Kit

To disconnect the flat flex cable from the Mini Card Host Extender or Dev Kit board:

1. Pull up on both arms of the brown clip on the connector at the same time to release the cable.

2. Pull the flat flex cable straight out of the connector.

Configure the Mini Card

The Dev Kit includes several switches and jumpers that you can use to configure the Mini Card’s operation, as detailed in Table 2-1 on page 19 through Table 2-5 on page 21, and Figure 2-15 on page 21. For a detailed schematic of the kit, see Schematic diagram on page 25.

Note: Some Dev Kit features are available for certain Mini Cards only. For example, the Audio and UART features are only available for voice-enabled Mini Cards.



Figure 2-14: Dev kit switches and jumpers

USB port

GND banana plug port

+3.3V banana plug port

+5V barrel jack power

Main UART D-sub9

Secondary UART D-sub9

VCC_3.3V adjust

SW4 power control

CN8 power routing options

Diversity RF SMA connector

Mini Card connector

SW1 LED/UART control

Main RF SMA connector

RESET switch

CN9 host adapter flex

SW3 audio control

CN18 analog header

USIM/RUIM card socket

Headset jack

CN25 board power select

Table 2-1: CN25—Board power (+5 V) selecta

a. Required: Select one option only (Jump 1–2 or Jump 5–6)

FunctionJump 1–2

Jump

3–4b

b. Pins 3 and 4 are not used

Jump 5–6

Power supplied by USB cable (through CN1–USB port)

Yes

Power supplied from Wall cube brick (through CN2–barrel jack power)

Yes

Table 2-2: CN8—Power routing optionsab

a. Required: Select either Jump 1–2 or Jump 3–4b. Jump 5–6 is optional—use only as needed

FunctionJump 1–2

Jump

3–42Jump 5–6

Enable onboard LDO to supply VCC_3.3V power from USB cable or wall cube (see Table 2-1 on page 19 for details)

Yes

Host Adapter Flex supplies VCC_3.3V Yes

Enable supercapacitor in circuit on VCC_3.3V node (useful for UMTS Mini Cards)

Yes



Table 2-3: SW3—Audio controla

Function Dip1 Dip2 Dip3 Dip4

+20 dB gain on MIC1P On Off

+0 dB gain on MIC1P Off On

+20 dB gain on MIC1N On Off

+0 dB gain on MIC1N Off On

a. For line-level audio devices such as TTY consoles, we recom-mend setting 0 dB MIC gain.

Table 2-4: SW1—LED / UART control

Function /(Label on board)

Dip On / Off State

Headset detect(EN HEADSET DET)

1 On Enable headset detect

Off (Default) Disable headset detect

Button detect(EN BUTTON DET)

2 On Enable button detect

Off (Default) Disable button detect

Green LED(EN GRN LED)

3 On Enable green LED

Off (Default) Disable green LED

Red LED(EN RED LED)

4 On Enable red LED

Off (Default) Disable red LED

MIO LEDs(EN MIO LEDS)

5 On Enable MIO LEDsEnable for voice modems (High = Led ON)

Off Disable MIO LEDsDisable for data modems

UART1 flow control(EN UART1 RTS/CTS)

6 On Enable RTS / CTS lines of UART1 (voice modules can be configured to support this function)

Off Disable RTS / CTS lines of UART1

UART1 signals(EN UART1 RI/CD/DTR/DSR)

7 On Enable CD / DTR / DSR / RI of UART1

Off Disable CD / DTR / DSR / RI of UART1

UART1 main transceiver(EN UART1 XCVR)

8 On Enable UART1 transceiver

Off Disable UART1 transceiver

UART3 secondary transceiver(EN UART3 XCVR)

9 On Enable UART3 transceiver

Off Disable UART3 transceiver



Figure 2-15: Audio test headers

Disable modem(DISABLE MODEM)

10 On Disable modemAssert (modem powerdown command)

Off Enable modemDe-assert (modem power up)

Table 2-5: SW4—Power control

Function Dip On / Off State

VCC_3.3V 1 On (Default) Fixed regulation from USB power or wall cube power at 3.30 V

Off Adjustable regulation from USB power or wall cube power at 3.30 V

2 On Enable onboard LDO (Low Drop Out) regulation of power from USB or wall cube

Off Disable onboard LDO

VCC_MSM26_DIGa

Note: Pins 3 and 4 must NOT be ON at the same time.

3 On (Default) Supplied by modem

Off Not supplied by modem

4 On Supplied by Dev Kit

Off Not supplied by Dev Kit

a. Required for voice-enabled modems; not required for data modems.Default setting for non-voice modems is Dip3–On and Dip4–Off.

Table 2-4: SW1—LED / UART control (Continued)

Function /(Label on board)

Dip On / Off State



Install / update Mini Card drivers and Watcher

The most recent CDMA and UMTS Mini Card software installation packages (drivers, and Watcher for Windows XP Professional and Windows Vista) are available from www.sierrawireless.com/minicard (registration is required).

If necessary, contact [email protected] for assistance, or to order the software on CD.

Download CDMA installer package

To download the CDMA Mini Card software installation package:

1. In your browser, go to www.sierrawireless.com/minicard (registration required).

2. Click the Docs & FW tab.

3. Click the EM/MC5xxx CDMA Firmware link.

4. Click the Watcher Versions link.

5. Click the most recent Watcher link.

6. When prompted, save the installer package to a local folder.

Table 2-6: Dev Kit—Module signal mapa

Pinb MC5727V MC5728V

MC5727MC8775MC8780MC8781MC8790MC8700

MC8201 MC8775V

MC8790VMC8791VMC8792VMC8795V

MIO6 GPIO32 GPIO3 NC GPIO_1 GPIO_1 GPIO_1



MIO30 GPIO27 GPIO19 NC GPIO_4 NC GPIO_4

MIO32 GPIO26 GPIO18 NC NC NC RI

MIO44 GPIO31 GPIO7 NC NC GPIO_4 DCD/GPIO_4

MIO46 GPIO30 GPIO2 NC NC GPIO_5 DSR/GPIO_5

MIO48 GPIO18 GPIO15 NC NC GPIO_6 DTR/GPIO_6

a. ‘GPIO*’—Firmware-assigned signal names.b. ‘MIO’—Multi-purpose I/O. These are the physical pins on the module.




mailto:[email protected]



Download UMTS installer package

To download the UMTS Mini Card software installation package:

1. In your browser, go to www.sierrawireless.com/minicard (registration required).

2. Click the Docs & FW tab.

3. Click the MC87xx GSM Firmware link.

4. Click the 3G Watcher and Drivers link.

5. Click the 3G Watcher Builds link.

6. Click the link for the most recent Watcher installer package (the File Type is MSI).

7. When prompted, save the installer package to a local folder.

Install CDMA or UMTS software

After downloading the appropriate installer package (CDMA or UMTS):

1. Run the installer package (.msi file). If the InstallShield Wizard window for Watcher appears, go to Step 2. Otherwise, if the Program Maintenance window appears, you have to remove an earlier version of Watcher before continuing:

a. Select Remove and click Next.

b. Click Remove. A window appears, showing the progress of the uninstall process, and then the InstallShield Wizard window appears when the uninstall is complete.

c. Click Finish.

d. Repeat Step 1 to install the new Watcher software.

2. The InstallShield Wizard Watcher Welcome window appears.

3. Click Install (CDMA) or Next (UMTS). The License Agreement appears.

4. Read the agreement, and then select I accept the terms in the license agreement.

5. Use the default folder (or click Change to select a different folder), and then click Next (CDMA) or Install (UMTS). A window appears, showing the progress of the installation process, and then the installation completed window appears.

6. Click Finish.





Rev 1.5 A

A
A: Schematic diagramNote: Table 2-6 on page 22 provides a cross-reference for signal names that differ between the various modules’ product specification documents.
Figure 1-1: Dev Kit schematic diagram (page 1 of 2)

RF

1R

F2

UA

RT

1_D

TR

_DS

R_C

D_

RI_

EN

RI1

XIM

_IN

DT

R

HS

_B

UT

TO

N_

N

HS

_DE

TE

CT

_N

0.1V

ref

1.0V

ref

2500

152

Min

iCar

d D

ev K

it

1 O

F 2

MIN

I C

AR

D D

EV

KIT

25001521

02-

05-

2008

CI

Thi

s do

cum

ent c

ont

ain

s in

form

atio

n w

hich

is

pro

prie

tary

and

co

nfid

ent

ial t

o S

ierr

a W

irele

ss

Inc.

Dis

clo

sure

to P

erso

ns

oth

er th

an

the

offic

ers,

em

ploy

ees,

ag

enst

or

subc

ontr

acto

rsof

the

com

pan

y or

lice

nsee

of t

his

docu

me

nt

with

out t

he

prio

r w

ritte

n pe

rmis

sio

n o

f Sie

rra

W

irele

ss In

c. is

str

ictly

pro

hib

ited.

Cop

yrig

ht (

C)

2004-2008

NO

NE

D

TIT

LE

:A

PP

RO

VA

LSD

ATE

PR

OJE

CT

:

DR

AW

N:

CH

EC

KE

D:

EN

GIN

EE

R:

SIZ

E

SC

AL

E:

FS

CM

NO

.D

WG

. N

O.

SH

EE

T:

SC

HE

MA

TIC

DIA

GR

AM

,

SH. DWG. NO.

AP

PR

OV

ED

DA

TE

DE

SC

RIP

TIO

NR

EV

RE

VIS

ION

S

12

34

56

78

ABCD

87

65

43

21

D C A

Sie

rra

Wire

less

PR

IMA

RY

RF

INTE

RFA

CE

CN

16U

.FL

-R-S

MT

10

9650

-111

3-0

17

CN

17

SE

CO

ND

AR

Y R

F IN

TE

RF

AC

EC

N14 U

.FL

-R-S

MT

10

965

0-1

113-

017

CN

15

C12

22pFDNI

C8

22pFDNI

XIM

_CLK

R14

60

R14

70

R1

480

R1

490

XIM

_IO

XIM

_RE

SE

T

VC

C_

2.6V

DIP

SW

ITC

HE

S

219

-10M

ST

P

SW

1

0ohms

R165

W_

DIS

AB

LE_N

EN

AB

LE_U

AR

T3

RE

SE

T_

N

EN

AB

LE_U

AR

T1

HO

ST

AD

AP

TE

R F

LEX

CN

9

FH

12A

-50S

-0.5

SH

VC

C_

2.6V

CT

S1

_XC

VR

RX

D1

TX

D1

RT

S1

_XC

VR

R386

100K

EN

AB

LE

_U

AR

T1

MIC

1_P

MIC

1_N

SP

K1_

P

SP

K1_

NC

TS

1_N

RT

S1

_N

RX

D1

TX

D1

MIO

6

XIM

_IO

XIM

_CL

K

XIM

_R

ES

ET

MIO

16

W_

DIS

AB

LE_N

AU

XV

1M

IO28

MIO

30

MIO

32

US

B-

US

B+

WW

AN

_LE

D

MIO

44

MIO

46

MIO

48

U1

1

MA

X32

38E

EA

I+T

UA

RT

1 X

CV

R

CN

11

574

784

4-2

1uF

C42

1uF

C43

1uF

C44

1uF

C45

MA

X32

38E

EA

I+T

U12

UA

RT3

XC

VR

5747

844

-2

CN

12

EN

AB

LE

_U

AR

T3

100K

R166

1uF

C4

6

1uF

C47

1uF

C48

1uF

C49

MIO

16

MIO

28

RE

SE

T_N

TP

33T

ES

TP

OIN

T_0

100

_R

ND

TP

34T

ES

TP

OIN

T_0

100

_R

ND

CN

10

SI-

583-

1HE

AD

SE

T JA

CK

2.5

MM

TC

74L

CX

125

FT

U1

7

C52

33u

F

MIO

48

VC

C_

2.6V

MIO

32

MIO

44

C5

3

0.1u

FC

57

0.0

1uF

C61

0.1u

F

C6

2

0.1

uF

C6

3

0.01

uF

C64

0.01

uF

C65

0.1uF

C66

0.01uF

33u

FC

67S

PK

1_P

SP

K1

_NM

IC1

P_

IN

MIC

1N

_IN

600o

hms

L1

600o

hms

L2

600o

hms

L3

600o

hms

L4

WW

AN

_LE

DLE

D_G

RN

LED

_RE

DE

MB

ED

DE

D_

LED

S_N

SML-310MTT86D31

SML-310LTT86D32

200o

hms

R18

3

200

ohm

s

R1

84

LED

_GR

N

LED

_R

ED

UA

RT

1_R

TS

_CT

S_E

N

MIO

46

R185

10K

R186

10K

R188

10K

R189

10K

U20

XC

620

4B

262M

R

ON

BO

AR

D 2

.6V

LD

O C68

1uF

C69

1uF

VC

C_L

DO

26_D

IGV

CC

_3.

3V

R20

5

0

DN

IR

TC

K

R20

6

0

DN

IT

DO

R20

7

0

DN

IT

CK

R20

8

0

DN

IT

MS

R20

9

0

DN

IT

DI

TR

ST

_N

R21

0

0

DN

I

R21

1

0

U2

1

TC

74L

CX

125

FT

UA

RT

1_R

TS

_C

TS

_EN

C7

0

0.1u

F

C7

1

0.0

1uF

CT

S1_

XC

VR

CT

S1

_N

RT

S1

_XC

VR

RT

S1_

N

TP

40

TP

41

TP

42T

P4

3

R212

1K

VC

C_2

.6V

R213

10KR214

10K

R21

5

1K

R21

6

1K

R21

7

1K

R2

18

1K

C73

4.7uF

C74

4.7uF

FTZ5_6E

D33

FTZ5_6E

D33

FTZ5_6E

D33FTZ5_6E

D33

0

R22

4

VC

C_

2.6V

MIO

28M

EG

A_

CM

D

R227

10K

R2

30

0oh

ms

R2

31

0ohm

s

R23

2

0ohm

s

R2

33

0oh

ms

SW

2

B3S

-10

02

PU

SH

-BU

TTO

N R

ES

ET

W_D

ISA

BL

E_N

R242

1M

R243

100K R244

100K

VC

C_2

.6V

VC

C_

2.6V

LMC

7101

AIM

5 N

OP

B

U25

LMC

7101

AIM

5 N

OP

B

U24

MIO

44

MIO

46

1%60.4K

R258

6.2K

R259

1%100K

R260

100K

R26

1

100K

R2

62

0.0

1uFC

82

0.01

uFC8

3

0.01uF

C84

0.01uF

C85

0.01uF

C86

0.01uF

C87

22pF

C88

22pF

C8

9

Q1

NS

BC

144

ED

XV

6T1

Q1

NS

BC

144

ED

XV

6T1

BA

S16

XV

2T1

D34

0 R

226

DN

I

MIO

48M

EG

A_C

LK

0 R

145

MIO

16M

EG

A_

DA

TA

CN

27

TF

-F-8

P-M

-E10

00

Mic

ro S

D

CD

1C

D2

MIO

44S

D_C

LK

MIO

46S

D_

CM

D

MIO

6S

D_

DA

TA

R1

250 0

R1

26

0 R

127

SD

SC

DA

6A01

01

CN

20

0

R121

DN

I

VC

C_3

.3V

R144

0

VC

C_2

.6V

10K

R122

1K

R12

8

R12

9

1K

R123

10K

MIO

16

MIO

28

SIM

CO

NN

EC

TO

R

2540

21M

A00

8G1

00Z

L

CN

13

DIP

1 :

ON

= E

N H

EA

DS

ET

DE

T;

OF

F=

DIS

HE

AD

SE

T D

ET

DIP

2 :

ON

= E

N B

UT

TO

N D

ET

; O

FF

=D

IS B

UT

TO

N D

ET

DIP

3-4

: O

N O

N S

ET

BIC

OLO

R W

AN

LE

D M

OD

E D

IP3

-4 :

OF

F O

FF

-D

IS W

AN

LE

D D

IP3

-4 :

ON

OF

F -

SE

T O

PE

N D

RA

IN W

AN

LE

D M

OD

E (

GR

N)

DIP

3-4

: O

FF

ON

-S

ET

CM

OS

WA

N L

ED

MO

DE

(R

ED

)D

IP5

: O

N =

EN

MIO

LE

DS

, OF

F=

DIS

MIO

LE

DS

DIP

6 :

ON

=E

N U

AR

T1

RT

S/C

TS

; O

FF

=D

IS U

AR

T1

RT

S/C

TS

DIP

7 :

ON

=E

N U

AR

T1

RI/C

D/D

TR

/DS

R O

FF

= D

IS U

AR

T1

RI/

CD

/DT

R/D

SR

DIP

8 :

ON

=E

N U

AR

T1

XC

VR

, O

FF

=D

IS U

AR

T1

XC

VR

DIP

9 :

ON

= E

N U

AR

T3

XC

VR

, OF

F=

DIS

UA

RT

3 X

CV

RD

IP10

: ON

= D

ISA

BLE

MO

DE

M,

OF

F=

EN

AB

LE M

OD

EM

DT

R1_

RS

232

RI1

_RS

232

CD

1_R

S23

2

DS

R1

_RS

232

Initi

al R

elea

se0

2-05

-20

08

AU

X_

PC

M_

CLK

AU

X_P

CM

_DIN

AU

X_

PC

M_

DO

UT

AU

X_P

CM

_SY

NC

RX

D1_

RS

232

CT

S1

_RS

232

TX

D1

_RS

232

RT

S1

_RS

232

1.0



Figure 1-2: Dev Kit schematic diagram (page 2 of 2)

02-

05-

2008

2 2500152

MIN

I C

AR

D D

EV

KIT 2

OF

2

Min

iCar

d D

ev K

it

CI

250

0152

Thi

s do

cum

ent c

ont

ain

s in

form

atio

n w

hich

is

pro

prie

tary

and

co

nfid

ent

ial t

o S

ierr

a W

irele

ss

Inc.

Dis

clo

sure

to P

erso

ns

oth

er th

an

the

offic

ers,

em

ploy

ees,

ag

enst

or

subc

ontr

acto

rsof

the

com

pan

y or

lice

nsee

of t

his

docu

me

nt

with

out t

he

prio

r w

ritte

n pe

rmis

sio

n o

f Sie

rra

W

irele

ss In

c. is

str

ictly

pro

hib

ited.

Cop

yrig

ht (

C)

2004-2008

NO

NE

D

TIT

LE

:A

PP

RO

VA

LSD

ATE

PR

OJE

CT

:

DR

AW

N:

CH

EC

KE

D:

EN

GIN

EE

R:

SIZ

E

SC

AL

E:

FS

CM

NO

.D

WG

. N

O.

SH

EE

T:

SC

HE

MA

TIC

DIA

GR

AM

,

SH. DWG. NO.

AP

PR

OV

ED

DA

TE

DE

SC

RIP

TIO

NR

EV

RE

VIS

ION

S

12

34

56

78

ABCD

87

65

43

21

D C A

Sie

rra

Wire

less

MIO

32

US

B+

RT

CK

TD

OT

CK

TM

ST

DI

TR

ST

_N

RT

S1_

N

TX

D1

CT

S1

_N

RX

D1

SP

K1_

PS

PK

1_N

MIC

1_P

MIC

1_N

W_D

ISA

BLE

_N

WW

AN

_LE

D

SW

4

219-

4M

ST

P

1%

R81

100K

U23

MIC

AM

P +

LP

F

AU

DIO

GA

IN S

TA

GE L

MC

7101

AIM

5 N

OP

B

MIC

1_P

MIC

1_N

CN

8T

SM

-103

-01-

L-D

V-M

-TR

CN

5

TS

M-1

10-0

1-L

-DV

C200

1uF

TP

201

5006

TP

202

500

6

XIM

_IO

XIM

_CL

KX

IM_

RE

SE

T

MIC

1P

_IN

MIC

1N_I

N

TR

ST

_NT

DI

TM

ST

CK

RE

SE

T_

N

RT

CK

TD

O

6791

0-0

001

CN

3

R102100K

D4

CM

S01

BA

RR

EL

JAC

K L

DO

U7

MIC

293

02W

U

RT

CK

TD

O

TC

KT

MS

TD

I

TR

ST

_NR

ES

ET

_N

VC

C_

5V

R113

10K

CN

2

RA

PC

712

X

5V J

AC

K

292

304-

1

CN

1

US

B C

ON

N

US

B+

US

B-

US

B-

430ohms

R124

22pF

C2

05

0.02

2uF

C2

06

0.001uF

C207

Fc

= 3

.39k

Hz

0.01

uF

C2

04

0.1uF

C209

0.1uF

C210

10K

R204

100K

R200

100K

R201

100K

R202

100K

R203

1%60.4K

R82

HS

201M

C21

1

Fle

x co

nnec

tor

plac

ed to

psi

de o

f bo

ard

CN

6

5274

5-10

96

RE

SE

T_

N

10V

C37

10uF

10V

C38

10uF

C39

10uF

C40

10uF

C41

10uF

MIO

6

MIO

16

AU

XV

1

CN

7

TS

M-1

10-0

1-L-

DV

DIG

ITA

L H

EA

DE

R

AU

XV

1

MIO

28M

IO30

MIO

44M

IO46

MIO

48

CT

S1

_NR

TS

1_N

RX

D1

TX

D1

TC

74L

CX

125

FT

U14

TC

74L

CX

125F

T

U1

5

330o

hm

s

R1

67

330o

hm

s

R1

68

330o

hm

s

R1

69

330o

hm

s

R1

70

330

ohm

s

R1

71

330

ohm

s

R1

72

330

ohm

s

R1

73

330

ohm

s

R1

74

330

ohm

s

R17

5

100

R17

6

100K

R177

EM

BE

DD

ED

_LE

DS

_N

EM

BE

DD

ED

_LE

DS

_N

EM

BE

DD

ED

_LE

DS

_N

MIO

6

MIO

16

MIO

28

MIO

30

MIO

32

MIO

44

MIO

46

MIO

48

MIO

6M

IO1

6M

IO2

8M

IO3

0

MIO

32M

IO4

4M

IO4

6M

IO4

8

XIM

_IO

XIM

_CLK

XIM

_R

ES

ET

SP

K1_

PS

PK

1_N

MIC

1_P

MIC

1_N

D1

3S

ML-

310M

TT

86

D1

4S

ML

-310

MT

T86

D15

SM

L-31

0MT

T86

D16

SM

L-31

0MT

T86

D17

SM

L-31

0MT

T86

D18

SM

L-31

0MT

T86

D19

SM

L-3

10M

TT

86

D20

SM

L-3

10M

TT

86

D21

SM

L-3

10M

TT

86

D22

SM

L-3

10M

TT

86

D23

SM

L-3

10M

TT

86

D24

SM

L-31

0MT

T86

D25

SM

L-31

0MT

T86

D26

SM

L-31

0MT

T86

330

ohm

s

R17

8

330

ohm

s

R17

9

330

ohm

s

R18

0

330

ohm

s

R18

1

TC

74L

CX

125F

T

U1

6

EM

BE

DD

ED

_LE

DS

_N

VC

C_

3.3V

RX

D1

TX

D1

RT

S1

_N

CT

S1

_N

1SMA12AT3

D27

C5

4

0.1u

F

C55

0.1u

F

C56

0.1

uF

C58

0.01

uF

C5

9

0.0

1uF

C60

0.01

uF

F1

181

2L15

00

CN

25

TS

M-1

03-

01-L

-DV

-M-T

R

4809

9-00

03

CN

4

TP

38

111-

070

3-00

1

BA

NA

NA

PLU

GS

TP

3911

1-0

702

-00

1

AN

ALO

G H

EA

DE

R

TS

M-1

10-0

1-L-

DV

CN

18

219

-4M

ST

P

SW

3

MIC

1P_I

NM

IC1N

_IN

U22

LMC

710

1AIM

5 N

OP

B

C75

0.01uF

C76

22pF

R219

1Mohms

C77

0.0

22uF

R2

20

47K

ohm

s

R221

91Kohms

C78

0.001uF

R222

51Kohms

R223

10K

R2

34

100K

R235

10K

R236

1Mohms

R23

7

47K

ohm

s

R238

91Kohms

R239

51Kohms

R240

10K

R24

1

100K

5006

TP

203

5006

TP

204

100K

R245

VC

C_2

.6V

TP

205

500

6

0.1u

F

C8

0

0.1u

F

C8

1

1M

R246

1M

R247

1M

R248

1M

R249

1M R250

1M R251

1M R252

1M R253

1M R254

1M R255

1M R256

1M R257

4809

9-40

00

CN

26

DN

I

R1

400o

hm

sW

_D

ISA

BLE

_N

CN

19

TS

W-1

02-

14-

T-S

TP

26T

ES

TP

OIN

T_

0080

_RN

D

5005

TP

200

10uF

C79

10V

TS

W-1

02-1

4-T

-S

CN

21

C208

0.1uF

JMP

1-2

: L

DO

SU

PP

LIE

S 3

.3V

JMP

3-4

: H

OS

T A

DA

PT

ER

SU

PP

LIE

S 3

.3V

JMP

5-6

: S

UP

ER

CA

PA

CIT

OR

IN C

IRC

UIT

MIN

ICA

RD

SM

T C

ON

NE

CTO

RM

INIC

AR

D L

ATC

HE

S

SIG

NA

L LE

DS

AR

M9

JTA

G H

EA

DE

RS

ee S

hee

t 1

AU

X_

PC

M_

CLK

AU

X_P

CM

_DIN

AU

X_

PC

M_

DO

UT

AU

X_P

CM

_S

YN

C

AU

X_

PC

M_

SY

NC

AU

X_P

CM

_DO

UT

AU

X_P

CM

_D

IN

AU

X_P

CM

_CL

K

UA

RT

3_T

X

UA

RT

3_R

X

AR

M9

JTA

G F

LEX

CO

NN

DIP

1: O

N=

EN

FIX

ED

OU

TP

UT

MO

DE

3.3

V, O

FF

=D

IS F

IXE

D O

UT

PU

T M

OD

ED

IP2:

ON

= E

N L

DO

; O

FF

= D

IS L

DO

DIP

3: O

N=

MO

DE

M S

UP

PLI

ES

2.6

VD

IG,

OF

F=

MC

8750

DIP

4: O

N=

ON

BO

AR

D L

DO

SU

PP

LY

2.6

V (

MC

875

0 O

NLY

), E

LSE

OF

F

JMP

1-2

: U

SB

CA

BLE

PW

RJM

P 5

-6 :

BA

RR

EL

JA

CK

PW

R

DIP

1 :

ON

=E

N M

IC_

P G

AIN

+2

0dB

, O

FF

= D

IS M

IC_P

GA

IND

IP2

: O

N=

EN

MIC

_N

GA

IN +

20d

B, O

FF

= D

IS M

IC_N

GA

IND

IP3

: O

N=

EN

MIC

_P

AM

P B

YP

AS

S;

OF

F=

DIS

MIC

_P A

MP

BY

PA

SS

DIP

4 :

ON

=E

N M

IC_

N A

MP

BY

PA

SS

; O

FF

= D

IS M

IC_N

AM

P B

YP

AS

S

PW

R L

ED

S


Rev 1.5 A

B
B: Bill of MaterialsTable B-1: Development kit bill of materials
Description Qty Reference designators

Vendors Vendor item numbers

CONN,2.5MM,4WIRE AUDIO JACK,RT-ANGLE,SMT

1 CN10 SENIOR INDUSTRIES

SI-583-1

CONNECTOR, ULTRA-MINIATURE, RF, 3.0X3.1mm

2 CN14,CN16 HIROSE UFL-R-SMT-1(10)

IPEX 20279-001E-01

CONNECTOR, MINI PCI EXPRESS, 52PIN, 0.8MM, RIGHT ANGLE

1 CN3 MOLEX 67910-0002

ZIF, 10 PIN, 0.5MM, RIGHT ANGLE 1 CN6 MOLEX 52745-1096

CONNECTOR, 6 PIN, 2.54mm DUAL ROW

2 CN8, CN25 SAMTEC TSM-103-01-L-DV-M-TR

TESTPOINT, COMPACT, THRU-HOLE, RED PLASTIC

1 TP200 KEYSTONE 5005

TESTPOINT, COMPACT, THRU-HOLE, BLACK PLASTIC

5 TP201, TP202, TP203, TP204, TP205

KEYSTONE 5006

HEADER, JTAG, SMT, 20 PIN 3 CN5, CN7, CN18 SAMTEC TSM-110-01-L-DV

CONNECTOR, RF, EDGE MOUNT, SMA TYPE, 0.062 BOARD THICKNES

2 CN15, CN17 APPLIED ENGINEERING

9650-1113-017

CONNECTOR, 50 PIN, ZIF, 0.5MM, TOP CONTACT TYPE

1 CN9 HIROSE FH12A-50S-0.5SH(55)

CONNECTOR, 4PIN, USB, THRU, RT ANGLE

1 CN1 TYCO 292304-1

CONNECTOR, 3 PIN, 2.5MM DC POWER JACK

1 CN2 SWITCH CRAFT RAPC712X

RAPC712

CONNECTOR, LATCH, MINI PC EXPRESS

1 CN4 MOLEX 48099-0003

BINDING POST, BANANA JACK, VERTICAL, BLACK

1 TP38 JOHNSON COMPONENTS

111-0703-001

KEYSTONE 7007

BINDING POST, BANANA JACK, VERTICAL, RED

1 TP39 JOHNSON COMPONENTS

111-0702-001

KEYSTONE 7006

CONNECTOR, RECEPTACLE, D-SUB, 9PIN, RIGHT ANGLE, 0.318 SERIES

2 CN11, CN12 Amp/Tyco 5747844-2



CONNECTOR, SIM, 8 PIN, HINGED, 29.20x17.40x2.3mm

1 CN13 SUYIN 254021MA008G100ZL

CONNECTOR, MicroSD SOCKET, PUSH/PUSH, STANDARD, 14x16x1.88mm

1 CN27 MIT TF-F-8P-M-E1000

CAP,SUPER,3.6V, 17.5x42MM 1 C211 CAP-XX HS201K

CAP-XX HS201M

CAP-XX HS201C

CAP, CER, 10µF, 10V,20%, X5R, 0805

6 C37, C38, C39, C40, C41, C79

TAIYO YUDEN LMK212C106MG

TAIYO YUDEN LMK212BJ106KD-T

MURATA GRM21BR61A106KE19L

CAP, CER, 1µF, 10%, 6.3V, 1005, X5R

11 C42, C43, C44, C45, C46, C47, C48, C49, C68, C69, C200

MURATA GRM155R60J105KE19D

TAIYO YUDEN JMK105BJ105KV-F

CAP, TANT., 33µF, 20%, 6.3V, 3528 2 C52, C67 KEMET T520T336M006ATE070

CAP,CER,4.7µF,20%,6.3V,SM,2012,X5R

2 C73, C74 TAIYO YUDEN CEJMK212BJ475MG-T

CAP,22pF, 50V, ±5%, C0G, 1005 4 C76, C88, C89, C205

TAIYO YUDEN UMK105CG220JV-F

MURATA GRM1555C1H220JZ01D

CAP, 1000pF, 50V, ±10%, X7R, 1005 2 C78, C207 MURATA GRM155R71H102KA01D

TAIYO YUDEN UMK105BJ102KV-F

CAP, 0.01µF, 25V, ±10%, X7R, 1005 16 C57, C58, C59, C60, C63, C64, C66, C71, C75, C82, C83, C84, C85, C86, C87, C204

MURATA GRM155R71E103KA01D

TAIYO YUDEN TMK105BJ103KV-F

CAP, 0.022µF, 16V, ±10%, X7R, 1005 2 C77, C206 MURATA GRM155R71C223KA01D

TAIYO YUDEN EMK105BJ223KV-F

Table B-1: Development kit bill of materials (Continued)




Bill of Materials

CAP, 0.1µF, 10V, ±10%, X5R, 1005 13 C53, C54, C55, C56, C61, C62, C65, C70, C80, C81, C208, C209, C210

MURATA GRM155R61A104KA01D

TAIYO YUDEN LMK105BJ104KV-F

RESISTOR, 60.4K, 1%, 1005, 1/16W, 50V, -55 +125C

2 R82, R258 ROHM MCR01MZPF6042

KOA SPEER RK73H1ETTP6042F

YAGEO RC0402FR-0760K4L

RES, 100, 5%, 1005, 1/16W, 50V, -55 +125C

1 R176 KOA SPEER RK73B1ETTP101J

YAGEO RC0402JR-07100RL

ROHM MCR01MZPJ101

RES, 200, 5%, 1005, 1/16W, 50V, -55 +125C

2 R183, R184 YAGEO RC0402JR-07200RL

KOA SPEER RK73B1ETTP201J

ROHM MCR01MZPJ201

RES, 330, 5%, 1005, 1/16W, 50V, -55 +125C

13 R167, R168, R169, R170, R171, R172, R173, R174, R175, R178, R179, R180, R181



ROHM MCR01MZPJ331

RES, 430, 5%, 1005, 1/16W, 50V, -55 +125C

1 R124 YAGEO RC0402JR-07430RL


ROHM MCR01MZPJ431

RES, 1.0K, 5%, 1005, 1/16W, 50V, -55 +125C

7 R128, R129, R212, R215, R216, R217, R218

YAGEO RC0402JR-071KL


ROHM MCR01MZPJ102

RES, 6.2K, 5%, 1005, 1/16W, 50V, -55 +125C

1 R259 VISHAY/DALE CRCW04026K20JNED

YAGEO RC0402JR-076K2L


ROHM MCR01MZPJ622






RES, 10K, 5%, 1005, 1/16W, 50V, -55 +125C

14 R113, R122, R123, R185, R186, R188, R189, R204, R213, R214, R223, R227, R235, R240



ROHM MCR01MZPJ103

RES, 47K, 5%, 1005, 1/16W, 50V, -55 +125C

2 R220, R237 YAGEO RC0402JR-0747KL


ROHM MCR01MZPJ473

RES, 91K, 5%, 1005, 1/16W, 50V, -55 +125C

4 R221, R22, R238, R239



ROHM MCR01MZPJ913

RES, 1.0M, 5%, 1005, 1/16W, 50V, -55 +125C

15 R219, R236, R242, R246, R247, R248, R249, R250, R251, R252, R253, R254, R255, R256, R257

YAGEO RC0402JR-071ML


ROHM MCR01MZPJ105

RES, 0.0 Ohm, 5%, 1005, 1/16W, 50V, -55 +125C

15 R125, R126, R127, R140, R144, R146, R147, R149, R165, R211, R224, R230, R231, R232, R233

KOA SPEER RK73Z1ETTD


ROHM MCR01MZPJ000

RES, POT, 100K, 30%, 0.05W 1 R102 PANASONIC EVN-5ESX50B15

RES, 100K, 1%, 1005, 1/16W, 50V, -55 +125C

16 R81, R166, R177, R200, R201, R202, R203, R234, R241, R243, R244, R245, R260, R261, R262, R386

YAGEO RC0402FR-07100KL

ROHM MCR01MZPF1003

KOA SPEER RK73H1ETTP1003F

IC, BUFFER, QUAD, 5V TOLERANT, TSSOP-14

5 U14, U15, U16, U17, U21

TOSHIBA TC74LCX125FT(EL)

ON SEMICONDUCTOR

MC74LCX125DTG

TOSHIBA TC74LCX125FT(EL)

IC,LDO,CMOS,LOW NOISE,150mA, 2.6V

1 U20 TOREX XC6204B262MR





Bill of Materials

ICS, RS-232 TRANSCEIVER, LOW-POWER, ESD, -40/+85C

2 U11, U12 TEXAS INSTRUMENTS

MAX3238EIDB

MAXIM MAX3238EEAI+T

IC, OP-AMP, LOW POWER, RAIL-TO-RAIL, SOT23-5

4 U22, U23, U24, U25

NATIONAL SEMICONDUCTOR

LMC7101AIM5NOPB

IC, LDO, 3A, ADJUSTABLE, TO-263-5

1 U7 MICREL MIC29302WU

XSTR, DUAL, NPN, 47K OHM BIAS RESISTORS

1 Q1 ON SEMICONDUCTOR

NSBC144EDXV6T1

ROHM EMH2

FERRITE BEAD, 600OHM@100MHz, 1005, MULTILAYER

4 L1, L2, L3, L4 TDK MMZ1005S601CT

TDK MMZ1005S601A

KOA SPEER CZB1EGTTP601P

MURATA BLM15AG601SN1D

TAIYO YUDEN BK1005HW601

DIO, BAS16XV2T1, SWITCHING, SOD-523

1 D34 ON SEMICONDUCTOR

BAS16XV2T1G

DIO, SCHOTTKY, 3A, 30V, 3.8x2.4x1.08

1 D4 TOSHIBA CMS01

LAMP,LED,SMD,1.6x0.8,3.6mcd@20mA,GRN

15 D13, D14, D15, D16, D17, D18, D19, D20, D21, D22, D23, D24, D25, D26, D31

ROHM SML-310MTT86

DIODE, ZEN,FTZ5.6, 5.6V/ 5MA,SC-74A

1 D33 ROHM FTZ5.6ET148

DIODE, TVS, 12V, 400WPEAK, SMA PACKAGE

1 D27 DIODES INC SMAJ12A-13-F

ON SEMICONDUCTOR

1SMA12AT3G

LAMP,LED,SMD,1.6x0.8,3.6mcd@20mA,RED

1 D32 ROHM SML-310LTT86

FUSE 1.5A, PTC, SLOW-BLOW 1 F1 LITTELFUSE 1812L150

SWITCH, TACT, 4 PIN 1 SW2 OMRON B3S-1002






SWITCH, DIP, 4-SPST, SEALED, MEDIUM, BLACK BODY

2 SW3, SW4 CTS 219-4MSTP

SWITCH, DIP, 10-SPST, SEALED, MEDIUM, BLACK BODY

1 SW1 CTS 219-10MSTP





Documents

AirPrime MC Series Dev Kit Quick Start Guide