AC

O S

pe

c if i

c at i

on

In

f or m

at i

on

www.acousa.com

Model number

Maximum flow*

L/s (gpm)

Volumesolids trap

L (gal)

Volumeoil storage

L (gal)

TotalcapacityL (gal)

Weightlbs

PartNo.

NS3/670 3 (48) 670 (177) 240 (64) 995 (263) 182.6 3913.80.00

62.7

6“ (1

594m

m)

47.6

4“ (1

210m

m)

1.18“ (30mm)

outlet

Ø51.97“ (1320mm)

inlet

48.4

3“ (1

230m

m)

Ø4“

Ø23.62“ (600mm)

T

Ø 4

“

Ø24.4“ (620mm)

T

Ø 4

“

load distibutionplate (concrete)

ACO ENVIRONMENT

NS3/670 OLEOPATOR P - MDPE vertical body oil-water separator

April 2018

Separator body

* Maximum flow indicated is for optimum performance - under 5mg/L hydrocarbons in effluent; higher flows can run through separator

PEDESTRIAN DUTY HEAVY DUTY

Cover with short

extension shaft

Extension shafts & covers

Cover only

Cover with deep

extension shaft Cover with

extension shaft

3.15

“ (8

0mm

)

31.5

0“ (8

00m

m)

68.1

1“ (1

730m

m)

74.1

7“ (1

884m

m)

Concrete

load

distribution

plate (by

others)

AC

O S

pe

c if i

c at i

on

In

f or m

at i

on

www.acousa.com

SPEC

INFO

April 2018

ACO, Inc.Northeast Sales Office9470 Pinecone DriveMentor, OH 44060Tel: (440) 639-7230 Toll free: (800) 543-4764Fax: (440) 639-7235

West Sales Office825 W. Beechcraft St.Casa Grande, AZ 85122Tel: (520) 421-9988 Toll Free: (888) 490-9552Fax: (520) 421-9899

Electronic Contact:info@acousa.comwww.acousa.com

© April 2018, ACO, Inc. This information is believed to be accurate but it is not guaranteed to be so. We cannot assume liability for results that buyer obtains with our product since conditions of use are beyond the control of the company. It is the customer’s responsibility to evaluate suitability and safety of product for his own use. ACO, Inc. reserves the right to change the product and specifications without notice. Re-order # EL009

Follow us onSoutheast Sales Office4211 Pleasant RoadFort Mill, SC 29708Toll free: (800) 543-4764Fax: (803) 802-1063

ACO ENVIRONMENT

NS3/670 OLEOPATOR P - MDPE vertical body oil-water separator

Specifications

GeneralThe oil water separator shall be ACO Oleopator P NS3/670 complete with ductile iron cover as manufactured by ACO, Inc.

MaterialsThe separator body shall be manufactured from medium density polyethylene (HDPE) and have minimum properties as follows:Tensile impact strength: 152 ft-lb/in2Tensile strength, ultimate: 3,480 psiWater absorption 0.01%Frost proof, salt proof and fuels and oils resistant

The oil separator shall be equipped with a coalescing unit and automatic shut-off valve for situations when maximum oil capacity is reached. Minimum oil storage capacity shall be 240 Liters (64 gal); minimum suspended solids storage capacity shall be 670 Liters (177 gal). Separator shall be resistant to uplift forces from underground water up to finished grade water table level. The oil separator should not require a concrete surround.

PerformanceThe effluent water should contain maximum 5mg/L (5ppm) for maximum designed flow. Independent performance testing should be available on request.

CoverCover shall be manufactured from ductile iron to ASTM A 536-84 – Grade 65-45-12 and have a minimum inside opening diameter of 600mm (24in). The cover should be marked ‘Separator’ on the top. The cover shall be capable of withstanding pedestrian / heavy vehicle traffic*.

Distance from finished grade to inlet pipe invert (T) shall be . . . mm (. . . in). (see tables for values).

AccessoriesThe separator shall be equipped with high liquid level alarm / maximum oil capacity alarm / maximum suspended solids capacity alarm** systems.

InstallationSeparator shall be installed in strict accordance with the manufacturer’s installation instructions and recommendations.

* Choose one /** Choose none, one or more

Tmm (inches)

Weightlbs

PartNo.

Cover only 420 (16.5) 298.0 3301.14.00

Cover & short extension shaft 730-1030 (28.7-40.6) 376.2 3301.14.01

Cover & deep extension shaft 730-1780 (28.7-70.1) 424.8 3301.14.02

Pedestrian Duty Top

Tmm (inches)

Weightlbs

PartNo.

Cover & extension shaft 865-1770 (34.0-69.7) 627.0 3301.17.00

Heavy Duty Top

NOTE: 1500mm (59in) diameter x 200mm thick concrete load distribution plate by others

54.2

1“ (1

377m

m)

39.3

7“ (1

000m

m)

1.18“ (30mm)

outlet

Ø51.97“ (1320mm)

inlet

40.1

6“ (1

020m

m)

Ø4“

Ø23.62“ (600mm)

T

Ø 4

“

Ø24.4“ (620mm)

T

Ø 4

“

load distibutionplate (concrete)

frame & cover

frame & cover

extension shaft

extension shaft

adaptor ring

Ø 4

“

Ø24.4“ (620mm)

T

load distibutionplate (concrete)

frame & cover

extension shaft

adaptor ring

Concrete load distribution

plate (by others)