6-Port Antenna Frequency Range 790–960 1710–2170 · PDF filePage 2 of 4 80010675V01 6-Port Antenna 936.4832/c ngmn 04.19.01.00 Subject to alteration. Highbands B1, connector 3–4

80010675V01 Page 1 of 4

6-Port AntennaFrequency RangeDual PolarizationHPBWAdjust. Electr. DTset by hand or by optional RCU (Remote Control Unit)

1710–2170 2490–2690790–960

X XX

65° 65°65°

2°–8° 2°–8°0°–10°

B1B1 Y1Y1R1R1

6-Port Antenna 790–960/1710–2170/2490–2690 65°/65°/65° 16/18/18dBi 0°–10°/2°–8°/2°–8°T

Type No. 80010675V01Lowband R1, connector 1–2R1, connector 1–2

790–960Frequency Range MHz 790 – 862 824 – 894 880 – 960

Gain at mid Tilt dBi 16.0 16.2 16.2

Gain over all Tilts dBi 15.9 ± 0.4 16.1 ± 0.3 16.1 ± 0.3

Horizontal Pattern:Azimuth Beamwidth ° 68 ± 1.0 68 ± 1.0 67 ± 0.9

Front-to-Back Ratio,Total Power, ± 30°

dB > 24 > 25 > 27

Cross Polar Discriminationover Sector

dB > 9.0 > 9.5 > 11.0

Vertical Pattern:Elevation Beamwidth ° 10.2 ± 0.3 10.0 ± 0.3 9.6 ± 0.3

Electrical Downtiltcontinuously adjustable

° 0.0 – 10.0

Tilt Accuracy ° < 0.4 < 0.3 < 0.4

First Upper Side Lobe Suppression

dB > 15 > 15 > 18

Cross Polar Isolation dB > 30

Port to Port Isolation dB > 30 (R1 // B1 // Y1)

Max. Effective Powerper Port

W 400 (at 50 °C ambient temperature)

Max. Effective PowerPort 1–2


Values based on NGMN-P-BASTA (version 9.6) requirements.

936.4

832/c

n

gm

n 0

4.1

9.0

1.0

0 S

ub

ject

to a

ltera

tio

n.

Kathrein USA Greenway Plaza II, 2400 Lakeside Blvd., Suite 650, Richardson TX 75082Phone: 214.238.8800 Fax: 214.238.8801 Email: [email protected]

All specifications are subject to change without notice.The latest specifications are available at www.kathreinusa.com

Page 2 of 4 80010675V01

6-Port Antenna

936.4

832/c

n

gm

n 0

4.1

9.0

1.0

0 S

ub

ject

to a

ltera

tio

n.

Highbands B1, connector 3–4B1, connector 3–4 Y1, connector 5–6Y1, connector 5–6

1710–2170 2490–2690Frequency Range MHz 1710 – 1880 1850 – 1990 1920 – 2170 2490 – 2690

Gain at mid Tilt dBi 18.1 18.2 18.4 17.9

Gain over all Tilts dBi 18.0 ± 0.4 18.1 ± 0.2 18.3 ± 0.5 17.8 ± 0.3

Horizontal Pattern:Azimuth Beamwidth ° 64 ± 5.9 64 ± 2.5 62 ± 3.9 63 ± 4.7

Front-to-Back Ratio,Total Power, ± 30°

dB > 23 > 25 > 25 > 22

Cross Polar Discriminationover Sector

dB > 7.5 > 11.0 > 10.5 > 10.0

Vertical Pattern:Elevation Beamwidth ° 4.9 ± 0.2 4.6 ± 0.2 4.4 ± 0.3 3.4 ± 0.2

Electrical Downtiltcontinuously adjustable

° 2.0 – 8.0 2.0 – 8.0

Tilt Accuracy ° < 0.2 < 0.2 < 0.2 < 0.2

First Upper Side Lobe Suppression

dB > 15 > 18 > 18 > 16

Cross Polar Isolation dB > 28

Port to Port Isolation dB > 30 (R1 // B1 // Y1)

Max. Effective Powerper Port


Max. Effective PowerPort 3–6





80010675V01 Page 3 of 4

Adjustment mechanismwith integrated scale

All dimensionsin mm | inches

1997 | 7

8.6

2027 |79.8

2067 | 8

1.4

2)

1)

1) 9 | 0.42) 64 | 2.5

For downtilt mounting use the clamps for an appropriate mast diameter together with the downtilt kit.Wall mounting: No additional mounting kit needed.

Material: Refl ector screen: Aluminum.Fiberglass housing: It covers totally the internal antenna components. The special design reduces the sealing areas to a minimum and guarantees the best weather protection. Fiberglass material guarantees optimum performance with regards to stability, stiffness, UV resistance and painting. The color of the radome is light grey.All nuts and bolts: Stainless steel or hot-dip galvanized steel.

Grounding: The metal parts of the antenna including the mounting kit and the inner conductors are DC grounded.

6-Port Antenna936.4

832/c

n

gm

n 0

4.1

9.0

1.0

0 S

ub

ject

to a

ltera

tio

n.

Accessories (order separately if required)

Type No. Description Remarksmm | inches

Weight approx.kg | lb

Units per antenna

85010002 1 clamp Mast diameter: 110 – 220 | 4.3 – 8.7 2.7 | 6.0 2


737978 1 downtilt kit Downtilt angle: 0° – 10° 2.3 | 5.1 1

Accessories (included in the scope of supply)


Electrical specifi cations, all systems

Impedance Ω 50

VSWR < 1.5

Return Loss dB > 14

Interband Isolation dB > 30

Passive Intermodulation dBc < –150 (2 x 43 dBm carrier)

Polarization ° +45, –45

Max. Effective Powerfor the Antenna

W900 (at 50 °C ambient

temperature)


Mechanical specifi cations

Input 6 x 7-16 female long neck

Connector Position bottom

Adjustment Mechanism 3x, Position bottom continuously adjustable

Wind load (at Rated Wind Speed: 150 km/h)

N | lbf Frontal: 390 | 88Maximal: 620 | 139

Max. Wind Velocity km/hmph

200124

Height / Width / Depth mminches

1997 / 300 / 15278.6 / 11.8 / 6.0

Category of Mounting Hardware

M (Medium)

Weight kglb

26.0 / 28.2 (clamps incl.)57.3 / 62.2 (clamps incl.)

Packing Size mminches

2361 / 322 / 19093.0 / 12.7 / 7.5

Scope of Supply Panel and 2 units of clamps for 42–115 mm |

1.7–4.5 inches diameter



Any previous data sheet issues have now become invalid.

Tilt 2490-2690Tilt 1710-2170Tilt 790-960

2 1

4 3

6 5

R1 R1 Y1 Y1

B1 B1

65.5 | 2.6

244 | 9.6

152 | 6

.0 *

48 | 1.9

101 | 4.0

221 | 8.7

173 | 6

.8 *

46 | 1

.8 84 | 3

.3

108 | 4

.3

49 | 1

.9

300 | 11.8 *

Bottom view* Dimensions refer to radomeAll dimensions in mm | inches

Layout of interface:

Correlation Table

Frequency range Array Connector

790– 960 MHz R1 1–2

1710–2170 MHz B1 3–4

2490–2690 MHz Y1 5–6

R1B1

Y1

1x

936.4

832/c

n

gm

n 0

4.1

9.0

1.0

0 S

ub

ject

to a

ltera

tio

n.

Page 4 of 4 80010675V01

6-Port Antenna



738546 Page 1 of 1

Mounting HardwareClamp Included in the Scope of Supply

936.

3920

/c

Sub

ject

to a

ltera

tion.

Suitable for mast diameter (mm)[inches]

42 – 115[1.65 – 4.53]

Antenna – mast distance (mm)[inches]

20 – 25[0.79 – 0.98]

Material of clamp and screws Hot-dip galvanized steel / stainless steel

Weight (kg)[lb]

1.1[2.43]

Please note: Kathrein does not recommend to use counter nuts.The additional nuts supplied are only meant as spares.

All dimensions in mm and [inches]

152 [5.98]

100 [3.94]40 [1.57]

72 [2.83]

35 [1.38]

64 [2.52]

125 [4.92]

40 [1

.57]

20–

25

[0.7

9–

0.98

]

42–115

[1.65–4.53]

M10 MA = 25 Nm

M8 MA = 20 Nm

20–25

[0.79–0.98]



Page 1 of 2

936.

4038

/a

Sub

ject

to a

ltera

tion.

General Instructionsfor Adjustment Mechanism

Description of the adjustment mechanism (protective cap removed):

Manual adjustment procedure:

Optional: RCU (Remote Control Unit) for remote-controlled downtilt adjustment:

For a description of RCU installation please refer to the respective data sheet.

Remove the protective cap.

➀ Adjustment wheel with twist-lockfunction.

➁ Downtilt spindle with integratedscale.

➀ Thread for fi xing the pro tectivecap or the RCU (Remote ControlUnit).

➁ Gearwheel for RCU power drive.

To set the downtilt angle exactly, you must look horizontally at the scale. The lower edge of the gear-wheel must be used for alignment.

Set downtilt angle by rotating the adjustment wheel.

Screw on the protective cap again.

0° – max.°

0° – max.°

1

2

2

1



Page 2 of 2

936.

4038

/a

Sub

ject

to a

ltera

tion.

General Instructions for Feederline Installation for Triple- and Quad-band Antennas

Please note: To avoid any damage to the interfaces, please ensure that only suitable tools are used. To tighten the feederline connector interfaces, we strongly recommend using a special Kathrein installation tool (as shown below) in combination with a standard torque-wrench.

Description of bottom end cap (exemplary picture):

There are eight feederline connectors and four adjustment mechanisms located at the bottom of the antenna.

Ventilation hole

Colour coding:Correlation of each RF input to:– the corresponding adjustment

mechanism– the frequency range– the polarization

7-16 female (long neck)

Spindle with tilting scale

Adjustment mechanism(protective cap removed)

Installation of the feederline connector and RCU (optional):In order to protect the adjustment mechanism the protective caps have to be attached during feederline installation!

For the feederline installation care fully put the connector in place and hand-screw the nut.

Use a torque-wrench to fi nish installation.

After feederline installation, the optional remote control units (RCU) R1, B1 and Y1 can be mounted if required. For a full description of RCU installation please refer to the respective data sheet.

These tools are suitable for 7-16 connectors with a wrench size of 27 or 32 mm, and the RCU attachment nut with a wrench size of 41 mm.

Tighten nuts within a torque range of 25 – 33 Nm depending on connector manufacturers’ specifi cations, respectively the RCU nut with a torque range of 15 – 18 Nm.

Kathrein installation set: Type No. 85010077Set has to be ordered separately!Set consists of three spanners of 27, 32 and 41 mm width.

32 mm

1/2 square actuationaccording to DIN 3120 Form C

41 m

m27 mm



Documents

6-Port Antenna Frequency Range 790–960 1710–2170 · PDF filePage 2 of 4 80010675V01 6-Port Antenna 936.4832/c ngmn 04.19.01.00 Subject to alteration. Highbands B1, connector 3–4