4850 d 99 Manual

7/31/2019 4850 d 99 Manual

1/52

IDEAL 4850-95

IDEAL 4850-95EP

IDEAL 5221-95EP IDEAL 6550-95EP

IDEAL 4810-95

GB Operating InstructionsGuillotines
http://www.whitakerbrothers.com/triumph-4850-d-cutterhttp://www.whitakerbrothers.com/triumph-4850-d-cutter

7/31/2019 4850 d 99 Manual

2/52

IDEAL 4810-95 IDEAL 4850-95/EP IDEAL 5221-95EP IDEAL 6550-95EP

- 2-

D Bitte lesen Sie vor Inbetriebnahme der Maschine unbedingt diese Betriebsanleitungund beachten Sie die Sicherheitshinweise. Die Betriebsanleitung muss jederzeitverfgbar sein.

GB Please read these operating instructions before putting the machine into operationand observe the safety precautions. The operating instructions must always beavailable.

F Nous vous prions de lire attentivement le mode demploi avant dutiliser la machine,et attirons votre attention sur les consignes de scurit. Les instructions d'utilisationet les consignes de scurit doivent toujours tre disponibles. Les instructionsd'utilisation et les consi.

NL Leest u voor de ingebruik name van het apparaat a.u.b. deze gebruiksaanwijzinggoed door en neemt u de veiligheidsinstructies n acht. De gebruiksaanwijzing ende veiligheids-voorschriften moeten altijd binnen handbereik zijn.

I Per favore legga questo manuale di istruzione prima di mettere in funzione ildistruggidocumenti e osservi le regole di sicurezza. Le istruzioni duso devonoessere sempre disponibili.

E Le recomendamos lea las instrucciones antes de poner en funcionamiento estamquina y cumpla las normas de seguridad. Las instrucciones de servicio yseguridad deben estar siempre disponibles.

S Ls igenom denna bruksanvisning innan ni startar maskinen. Var noga medskerhetsfreskrifterna. Instruktionsmanualen mste alltid finnas tillgnglig.

FIN Lue nm kytt-ohjeet lpi ennenkuin kynnistt laitteen !Noudata turvaohjeita. Kyttohjeiden on oltava aina saatavilla.

N Lees gjennom denne bruksannvisningen fr De tar i bruk maskinenVr oppmerksom p sikkerhetsforskriftene. Opperatrmanualenm alltid vre tilgjengelig.

PL Prosz uwanie przeczyta instrukcj obsugi przed uruchomieniem urzdzenia istosowa si do przepisw bezpieczestwa. Instrukcje obsugi muszbyzawsze dostpne.

RUS , , . .

H A gp zembe helyezse elott figyelmesen olvassa el a kezelsi utastst s tartsabe a biztonsgi elorsokat.Kezelsi utastsnak mindig elrhetonek kell lennie.

TR Ltfen makineyi altrmadan nce bu kullanma talimatlarn dikkatli bir ekildeokuyunuz ve belirtilen gvenlik nlemlerine uyunuz. Kullanma Talimatlarher zaman kullanma hazr olmaldr.

DK Fr installation af maskinen bedes De venligst lse brugervejledningenbrugervejledningen og vre opmrksom p sikkerhedsanvisningerne.Brugervejledningen skal altid vre tilgngelig.

CZ Prosm pette si instrukce k obsluze a dodrujte bezpenostn

upozornn. Nvod k obsluze mus bt vdy dostupn.P Por favor leiam o manual de instrues antes de colocar a mquina em operaoe vejam as precaues de segurana. As instrues de operao devero estarsempre disponveis.

GR . .

SLO Prosimo preberite navodila za uporabo ter upotevajte varnostna opozorilapreden zaenete naparavo. Navodila naj bodo vedno pri roki.

SK Starostlivo si pretudujte tento nvod na obsluhu pred uvedenm stroja doprevdzky a najm bezpecnostn predpisy. Drte tento nvod na obsluhu nadostupnom mieste.

EST Palun lugege enne masina kivitamist kesolevat kasutusjuhendit ning jrgigeohutusnudeid. Kasutusjuhend peab alati keprast olema.

CHI

UAE

Safety precautions
http://www.whitakerbrothers.com/triumph-4850-d-cutterhttp://www.whitakerbrothers.com/triumph-4850-d-cutter

7/31/2019 4850 d 99 Manual

3/52- 3 -

D Keine Bedienung durch Kinder!GB Children must not operate the machine!F Pas dutilisation par un enfant!

NL Geen bediening door kinderen!I Non lasciare utilizzare il tagliacarte a bambini!E No dejar que la utilicen los nios!S Installera maskinen utom rckhll fr barn!

FIN Asentakaa laite lasten ulottumattomiin !N Installer maskinen utenfor rekkevidde for barn!PL Dzieciom nie wolno obsugiwa urzdzenia !

RUS !H Gyerekek a gpet nem kezelhetik

TR Makinay ocuklar Kullanmamaldr.DK M kun betjenes af voksne

CZ Stroj nesm bt obsluhovn dtmi!P As crianas no devem trabalhar com a mquina!

GR .SLO Otroci ne smejo uporabljati napraveSK So strojom nesm pracovat deti!EST Lapsed ei tohi masinat kasutada!CHIUAE

D Nicht unter das Messer fassen!GB Do not reach beneath the blade!F Ne pas passer les mains sous la lame!

NL Niet met de handen onder het mes komen!I Non toccare la lama nella parte inferiore!E No tocar debajo de la cuchilla!S Strck inte in handen under kniven!

FIN l laita kttsi tern alle !N Plasser aldri hender ol. under kniven !PL Nie wkada rk pod noe!

RUS !H Ne nyljon a ks al!TR Elinizi ban altna sokmaynz!DK Stik ikke hnderne ind under knivbladet!CZ Nesahejte pod ost noe!P No tocar na parte inferior da faca!

GR !SLO Ne segajte z roko pod rezilo!SK Nevkladajte ruky pod n!EST rge pange ktt tera alla!CHI

UAE

Safety precautions
http://www.whitakerbrothers.com/triumph-4850-d-cutter

7/31/2019 4850 d 99 Manual

4/52- 4 -


Safety precautions

D Messer nie lose liegen lassen!Messer nur mit Messerwechselvorrichtung oder imMessertransportkasten befrdern!

(siehe Seite 33 und 35).Warnung! Verletzungsgefahr!GB Never leave the blade unattended!

Do not extract or transport the blade without protection!(See page 33 and 35).

Danger! Risk of injury!F Ne jamais laisser la lame sans protections !

Elle ne doit tre dmonte qu l aide du dispositif dechangement de lame (cf. page 33 et 35), ou transporte dansson tui en bois !

Danger! Risques de coupures !

NL Laat nooit de messen alleen achter.Transporteer de messen niet zonder de houten bescherming(zie pagina 33 en 35).

Waarschuwing! Opgelet voor ongevallen!I Non lasciare mai la lama incustodita. Non rimuovere o

trasportare la lama senza protezione. (Vedi pagina 33 e 35).Attenzione! Rischio di infortunio!

E No quitar la cuchilla sin prestar atencin. No desmontar notransportar la cuchilla sin proteccin! (vrase pg. 33 y 35)

Advertencia! Peligro de hacerse dao!S Lmna aldrig maskinen obemannad. Ta inte ur eller

transportera kniven utan skydd. (se sid 33 och 35). Skaderisk!

FIN Ksittele ter aina varoen. l siirr tai kuljetater ilman suojaa ! (katso sivu 33 ja 35

Loukkaantumisen vaara !N La aldri kniven ligge ubeskyttet. Ta aldri ut kniven eller

transporter den uten beskyttelse (Se side 33 og 35)FARE ! Muligheter for skade !

PL Nigdy nie pozostawia noy bez nadzoru.Nie wyciga lub transportowa noy bez oson!

(zobacz strona 33 i 35).Ryzykoskaleczenia sie!RUS !

!(. 33 35) ! ! ! ! !

H Soha ne hagyja a kst rizetlenl!Ne vegye ki vagy ne szlltsa a kst vdtok nlkl!(Lsd 33. s 35. oldal)

Veszly! Srlsveszly!TR Ba hibir zaman gzetimsiz brakmaynz!

Ba muhafazasz olarak yerinden kartmaynz veyatamaynz! (Sayfa 33 ve 35e baknz)

Dikkat! Yaralanma riski!

7/31/2019 4850 d 99 Manual

5/52- 5 -

Safety precautions

3335

3533

DK Knivbladet m aldrig efterlades uden opsyn.Forsg ikke at afmontere eller transportere knivbladet udenbeskyttelse! (Se side 33 og 35)

FARE!Risiko for legemlig beskadigelse.CZ Nikdy nenechvejte n bez krytu.Nikdy nevyjmejte nebo neprepravujte nuz bez ochrannhokrytu (viz. strany 33 a 35)

Nebezpec!Riskujete zranenP Deixar a faca sempre em local seguro!

No retirar ou transportar a faca sem proteco!(Ver pg. 33 e 35)

Perigo! Risco de dano!GR !

( 33 & 35) ! !

SLO Nikoli ne puajte rezila nazaitenega. Nikoli ne prenaajterezilo brez zaite. ( glej stran 33 in 35).

Pozor!Pozor!Pozor!Pozor!Pozor! Nevarnost pokodbe.Nevarnost pokodbe.Nevarnost pokodbe.Nevarnost pokodbe.Nevarnost pokodbe.SK Nenechvajte n nechrnen (nezabezpecen)!

Nevyberajte alebo netransportujte n bez ochrany(vid s. 33 a 35)

! Riziko razu !! Riziko razu !! Riziko razu !! Riziko razu !! Riziko razu !EST rge jtke liketera kunagi jrelevalveta!

rge pikendage ega teisaldage tera kaitseseadmeteta!(Vt lk 33 ja 35)

Oht!Vigastuste oht!CHI

UAE

7/31/2019 4850 d 99 Manual

6/52- 6 -


D Keine harten und splitternden Materialien schneiden!GB Do not cut hard materials or materials which may splinter!F La coupe de matriaux trop durs ou risquant des projections

est interdite !NL Snij geen harde materialen of materiaal dat kan splinteren!I Utilizzare il tagliacarte esclusivamente per il taglio di risme

di carta o materiali analoghi!E No cortar materiales duros o materiales que puedan

astillarse!S Frstr inte hrt material eller material som kan splittras!

FIN Asentakaa laite lasten ulottumattomiin !N Ikke kutt hardt metall eller materiale som kan splintre !PL Nie ci twardych materiaw lub materiaw, ktre mog

ulec odpryniciu!

RUS , !

H Ne vgjon kemny vagy olyan anyagot, amely repedhet!TR Sert veya paralanabilecek malzemeleri kesmeyiniz!DK Der m ikke skres i hrde materialer eller i materialer, der

kan splintre!CZ Neete tvrd materil, pi kterm mohou ustelovat ostr

lomky!P No cortar materiais duros ou materiais que possam lascar!

GR !

SLO Nikoli ne reite trdih materialov ali materialov, ki se lahkorazcepijo.

SK Nerete tvrd materily, alebo materily, z ktorch muvystrelovat ostr lomky.

EST rge ligake kvasid materjale ega materjale, mis vivadpilbasteks puruneda!

CHIUAE

Safety precautions

7/31/2019 4850 d 99 Manual

7/52- 7 -

The machine is designed for cutting stacks ofpaper to a specified size.This machine is constructed for "one-man

operation" only!Warning! Clips or similar damage thecutting blade.

Disconnect from the mains before starting anyservice work or before removing the panels!

Replacement of blade and cutting stick maybe performed only when the main switch isswitched off!

Safety precautions

7/31/2019 4850 d 99 Manual

8/52- 8 -


A

A A

B

C

AC

All components which could endanger theoperator are covered by a guard!

Operating the machine without safety device isforbidden!(Front safety guard (A), rear screwed safetyguard (B) and panel (C).

Safety precautions

7/31/2019 4850 d 99 Manual

9/52- 9 -

C

A

B

The dangerous cutting movement issafeguarded by a movable guard (A) and asafety two-handed control system! (B)

Before working with the machine and afterevery blade replacement the automatic cut-offfunction of safety guard (A),(correct if distancebetween cover and table is < 20 mm) mainswitch (B) and control panel (C) must bechecked.

Safety precautions

7/31/2019 4850 d 99 Manual

10/52- 10 -


230V / 10A min115V / 15A min

Protect mains cable against heat, oil andsharp edges!

Connect the power cord to a single phasesocket.

Ensure free access to mains!

Safety precautions

7/31/2019 4850 d 99 Manual

11/52- 11 -

When not in use for a longer period switch off.(Main switch to "0").

Safety precautions

Clamping BladeOK

OK

Warning by IDEAL 4810-95Danger!

Blade must always be covered by thepressing bar.

7/31/2019 4850 d 99 Manual

12/52- 12 -


B

C

A

4 x

Only IDEAL 4810-95, IDEAL 4850-95/EP,IDEAL 6550-95EPRemove the stand from the wooden pallet.

Only IDEAL 4810-95, IDEAL 4850-95/EP,IDEAL 6550-95EP4 strong people are required to lift the machinefrom the pallet and place it on the stand.

Secure with 4 screws (A). Put the shelf (B) onthe stand. (Parts and tools are in the tool set(C).

Installation

7/31/2019 4850 d 99 Manual

13/52- 13 -

AC

A

C

Only IDEAL 4810-95, IDEAL 4850-95Tighten the backgauge crank (A). Parts andtools are in the tool set (C).

Installation

IDEAL 5221-95EPThe machine is delivered ready for operation.4 strong people are required to lift the

machine from the pallet.Side tables, left and right, (A) are availableas accessories.Attach the side tables to the front table sothat the upper surface is level.(Screws and nuts are in a plastic bag in thetool set (C).The front and rear wooden panels must beremoved for in-house transport on a pallettruck.For transport through narrow doors: Remove side tables Remove the machine from its base

(4 screws) Tilt the machine on its side Mount the machine to its base Screw on all side panels

7/31/2019 4850 d 99 Manual

14/52- 14 -


C

Only IDEAL 4810-95Attach the enclosed hand-wheel for clamping.Parts and tools are in the tool set (C).

Plug into socket.The machine must be connected directly to thesocket.

Installation

7/31/2019 4850 d 99 Manual

15/52- 15 -

A

A A

X

BB

It is forbidden to operate the machine if theoperating and safety instructions have not beenunderstood. Please check the safety devices

are functioning and complete before use. All covers have to be mounted (A). The release for cutting is allowed only if

the cover is closed and the two-hand safetydevice is operated at the same time (B)

If the front cover closes by itself thegas spring (X) needs replacing.

We recommend you keep a record of your testresults.

Operation

7/31/2019 4850 d 99 Manual

16/52- 16 -


C A

B

D

A

B

Position the main switch to "I" (A). Insert thekey for the control system and move it to theright (B). Open the safety guard (C). The

machine is now ready for use.

Only IDEAL 4850-95EP, IDEAL 5221-95EP,IDEAL 6550-95EPPress S button (D).Machine will automatically go to the startposition.

IDEAL 4850-95EP, IDEAL 5221-95EP,IDEAL 6550-95EPThe measurement is set either with the hand-wheel (A) or by programming (B) the cuttingmeasurements. Measurement is shown on thedisplay in inches or cm (B).

Operation

7/31/2019 4850 d 99 Manual

17/52- 17 -

A

B

C

D

E

IDEAL 4810-95, IDEAL 4850-95The measurement is set with the backgaugecrank.(A) The symbol rotary direction

moves to the right on the display (B) (seepicture C). The rotary direction of thebackgauge crank (A) is indicated on the right.Keep turning the backgauge crank to the rightuntil a measurement appears (see picture E).The reference position is reached.The cutting size can now be set with thehandle (A).If the backgauge is right at the front thesymbol rotary direction will move to the left(see picture D). Turn the backgauge crank to

the left until the rotary direction appears on theright in the display (see picture C).Afterwards turn the backgauge crank to theright until a measurements appears (seepicture E). The reference position is reached.The cutting size can now be set with thehandle (A). Proceed to position from therear.

Measurement is shown on the display ininches or cm (B).

Information:When the machine is only switched off bythe Key switchH (main switchF is still ON)it is not necessary to advance to thereference point when a new measurement isinserted.

Operation

7/31/2019 4850 d 99 Manual

18/52- 18 -


A

B

Optical cutting line (A) that indicates the exactposition of the cut. Blade cuts on the frontedge (B) of the light beam. (Only use when no

exact cut is required).

Only IDEAL 4810-95, IDEAL4850-95.Pull out the handle to avoid the measurementbeing wrongly adjusted.

Operation

7/31/2019 4850 d 99 Manual

19/52- 19 -

B

A

B

C

Position the paper on the backgauge (A) andside lays left or right (B).To move paper stacks, please use the paper

knock-up block (C) provided.(Run backgauge to the front for turning thepaper stack).

Operation

7/31/2019 4850 d 99 Manual

20/52- 20 -


A

+ =

+ =

+ =

IDEAL 4850-95/EP, IDEAL 5221-95EPIDEAL 6550-95/EPThe clamp moves automatically when cutting

is activated.

The paper can also be pressed in advance.Clamping and cutting is activated bypressing button (A) on the front table.

Pre-clamping

Clamp returns

Cutting sequence with automatic clamping

Only 4810-95Clamping is released by the hand-wheel.

Before every cut lower the clamp by turning thehand-wheel to the right and tighten with a lighttwist. The cut is activated by pressing the twobuttons exactly at the same time.

Operation

7/31/2019 4850 d 99 Manual

21/52- 21 -

Close the safety guard.

Cutting activation:Press both buttons of the two-handed controlsystem activation (A) simultaneously and thempressed until the paper is completely cut.

To interrupt or stop cutting:To interrupt or stop cutting, releaseboth buttons (A) of the two-hand control.

Operation

7/31/2019 4850 d 99 Manual

22/52- 22 -


Operating elements

A - Front safety guard

B - Safety two-handed control systemPre-clamping and cutting

C - Overload switch(blade drive/clamp drive/backgauge drive)D - Backgauge control (EP)

E - Paper clamp(only IDEAL 4810-95)

F - Main switch

G - Hand-wheel (EP) or crank handlefor backgauge setting

H - Key switch

I - Backgauge

J - Side lay left and right

K - Display cutting size (EP, cm or inch)

L - Select program step up (Programming)or fixed dimension (Standard 21 cm)

M - Select program step down (Programming)or fixed dimension (Standard 10,5 cm)

N - Stop and delete input

O - Start

P - Memory multiple cut

Q - Keypad

R - Changeover cm - inch (LED - display)

S - Clear program

T - Select program

U - Enter

V - Program number

W - Program step

X - Cut is blocked

Y - Display multiple cut

Z - Display cutting size (cm or inch)

a - Changeover cm/inch

b - Measuring unit (cm or inch)

Operation

Only IDEAL 4850-95/EP,IDEAL 5221-95/EP, IDEAL 6550-95/EP

Only IDEAL 4810-95, IDEAL 4850-95

7/31/2019 4850 d 99 Manual

23/52- 23 -

A

B

C

D

E

IDEAL 4810-95, IDEAL 4850-95

Operation

IDEAL 4810-95, IDEAL 4850-95/EP,IDEAL 5221-95EP, IDEAL 6550-95EPStart machine

Main switchF to position "I", insert the keyH for the control panel and turn it to the right.Open the front safety guardA

Only by IDEAL 4810-95, IDEAL 4850-95Cutting to specified dimensions The measurement is set with the backgauge

crank.(A) The symbol rotary direction moves to the right on the display (B) (seepicture C). The rotary direction of the(backgauge crank (A) is indicated on the

right. Keep turning the backgauge crank tothe right until a measurement appears(see picture E).The reference position is reached. Thecutting size can now be set with thehandle (A).If the backgauge is right at the front thesymbol rotary direction ill move tothe left (see picture D). Turn the backgaugecrank to the left until the rotary directionappears on the right in the display (seepicture C). Afterwards turn the backgaugecrank to the right until a measurementsappears (see picture E). The referenceposition is reached. The cutting size can nowbe set with the handle (A). Proceed toposition from the rear.The measurement scale in cm or inch has aLED displaya. For information on how tostore see page 22, picture below left.

Insert paper and move by means of the

stacking angle to the backgaugeI and sidelay on the leftJ.Turn the hand-wheelEfor paper clamping tothe right and tighten with a short twist.

Close the front safety guardA. Release the cut.

Cut according to markings Adjust the backgauge with the crank handleG to the back.

Insert paper and move by means of the

stacking angle to the backgaugeI and sidelay on the leftJ. Turn the crank handleG to the right until the

marking on the paper to be cut is below thecutting line indicator.

7/31/2019 4850 d 99 Manual

24/52- 24 -


IDEAL 4850-95EP,IDEAL 5221-95EP, IDEAL 6550-95EPStart machine Main switchF to position "I", insert the keyH for the control panel and turn it to the right.Open the front safety guardA

Press S buttonO backgaugeImovesto the rear and searches for the referenceposition, wait until a measurementis shown in the displayD.IDEAL 4850-95/EP = 45 cm, 17,72 inchesIDEAL 5221-95EP = 52 cm, 20,47 inchesIDEAL 6550-95/EP = 61 cm, 24,02 inches

Warning!Before storing or cutting a measurementplease check if the correct measurementscale (cm or inch) see above is stored.For information on how to store see picturebelow left.

Cutting to specified dimensions Enter dimension on the numerical key padQ LED "S"X appears.(If a wrong dimension is entered this can becorrected by pressing the s button).

Press S button dimension isapproached, LED "S" disappears.

Dimensions below 9 cm 3,5 cm (IDEAL6550-95EP 2,5 cm) can only be approachedwith the Sbutton pressed and held. (Whenthe S buttonO is released, the backgaugeImoves to a measurement of 9 cm measurement 9 cm blinks, keepthe S button pressed, backgaugeImovesto e.g. 7 cm.

Insert paper and move by means of thestacking angle to the backgaugeI and sidelay on the leftJ.

Close the front safety guardA.

Release the cut.Cut according to markings Adjust the backgauge with the hand-wheelG

to the back. Insert paper and move by means of the

stacking angle to the backgaugeI and sidelay on the leftJ.

Turn the hand-wheelG to the right until themarking on the paper to be cut is below thecutting line indicator.

Only EP machines. The further the hand-wheelGis turned to the right, the quicker thebackgauge moves. If the hand-wheel isturned to the left the backgauge will returnquicker.

Operation

7/31/2019 4850 d 99 Manual

25/52- 25 -

Operation

Eject functionIf buttonjM is pressed instead of button SO,after inserting the measurementQ, thebackgauge will advance forwards so that

paper can be removed. Finally the backgaugemoves to the last setting.

Adjust the eject-dimension Press p, hold, and press Te on

display. Insert the desired dimension.

(Standard is 20 cm). g Store dimension. p + sEscape the program mode.Program buttonsbandjprogramsPressp, hold, and pressb ( appears onthe display) orPressp, hold, and pressj ( appearson the display) Enter the desired dimension (For example:

29,7 cm x 21 cm can be entered for DIN A4) gStore dimension.Display in cm or inch Press i display changes between cm

and inch (see page 22 and 24).

Cutting activationWarning!

Run backgauge to the front for turning thepaper stack. Do not interrupt the upward movement of the

blade by performing switching procedures. Release blade only when LED "S"X has gone

out. Close the front safety guardA. Blade must always be at the top and be

covered by the clamp. Do not touch theblade.(see safety information on page 38).

Risk of injury!

Multiple cutEnter the start dimension on the display Q.Advance to the measurement with theS

button.Push the paper to the backgaugeI.Press T button the red LED "M "Y light

will be on.Enter the multiple cut size.After cutting has been activated press S

button.Every time the S button is pressed,thebackgauge will advance by the multiple cutsize.

Pressing the s buttonN shows the actualsize.

Exiting program-modePree T button LED "M "Y is cleared on

the display.

7/31/2019 4850 d 99 Manual

26/52- 26 -


ProgrammingOnly IDEAL 4850-95EP, IDEAL 5221-95EP,DEAL 6550-95EP

This control system enables you to store 99programs with 99 programmable steps. Onestep represents one measurement. Afterentering the program numbers you are able tochange between several program steps withthe buttonj andb .First figure on display = program number.Second figure = program step.Dimensions below 9 cm/3,54 inch can onlybe approached with the S button held pressed."u" on the display the entered dimension istoo low."o" on the display the entered dimension istoo high.Each program step corresponds to onedimension. The indicated program step can beoverwritten at any time. These programsremain stored when the machine is off. Shouldyou change to another dimension unit allprogrammed measurements are converted intothe new unit (cm or inch).

Entering a programPress pP appears on the display.01 ... 99 Enter program number 01 ... 99.

(Top numberV on display = program number). If measurement is shown on the displayK the

program is reserved.Enter dimension, or move the backgauge to

the desired measurement with thehand-wheel G.

g Store the dimension next program stepappearsW.

Enter the next dimension.Should an ejection be desired before this cutpress p, hold, and press T.

g Store the dimension next program stepappears.

Should the entered program be requiredimmediately press S(program is closed).Press Sagain (backgauge moves to thedimension of the first program).Or:

p + s Escape the program mode.

Operation

7/31/2019 4850 d 99 Manual

27/52- 27 -

Eject function programThe eject function can be added each time ameasurement is entered and ejects before

advancing to the next measurement.An eject at the end of a program must beprogrammed in the first step at the program.If the dimension and eject function are stored inthe program step the program number appearson the displayV.

Example of a program eject function p0 8 program 08 c c delete previous program 1 6 g step 1 on 16,0 cm

2 0 step 2 on 20,0 cm Press p, hold, and press T eject (e blinks) g Store the dimension p s escape the program mode

How the example works p0 8 start program 08 S proceeds to position Insert paper Release cut 1 Press Sbutton Paper is ejected (V blinks) Turn the paper Release cut 2 p s escape the program mode

Programming of multiple cut dimensionp Press "X" appears on the display.0 1 ... 99 Enter program number 01 ... 99.

Top number on display = program number.

Lower number = program step.Enter the cut size on the displayQ.g Store the dimension.Enter multiple cut size.

Press Tbutton EWand multiple cut sizeappears on the display.Press Tbutton again F..... N.

g Store the dimension.p + s Escape the program mode.Maximum nine multiple cuts can be entered.

Operation

7/31/2019 4850 d 99 Manual

28/52- 28 -

IDEAL 4810-95 IDEAL 4850-95/EP IDEAL 5221-95EP IDEAL 6550-95EPOperation

Cancel a programp press "X" appears on the display.0 1 ... 99 Enter program number 01 ... 99.

Press button ctwice.Each program has to be cancelled separately.Deleting a dimension when programmingPress s and overwrite the dimension.

Choose a program step appears.Press p, hold, and press T W lights.Enter the desired number of steps (e.g. 0 5).

Change a step

b next stepj previous step

Insert a stepPress p, hold, and pressbA newprogram step is inserted before the displayedprogram step is shown.

Delete a stepPress p, hold, and pressjProgram stepis deleted.The following number of steps are updated.

7/31/2019 4850 d 99 Manual

29/52- 29 -

Working with programs Press p "X"appears on the display 01... 99 Enter program number 01 ... 99With the buttonj andb you are able tochange between several program steps.With S the backgauge moves to the indicateddimension.With s the backgauge stops.

GeneralLED "S" lights Cut is blocked.LED "S" is off the actual dimension appears.In the program mode the ejection of paperjis not possible. The ejection of paper has tobe programmed.

Escape the program mode Press p "X" appears on the display. Press s escape the program mode.

Operation

7/31/2019 4850 d 99 Manual

30/52- 30 -

IDEAL 4810-95 IDEAL 4850-95/EP IDEAL 5221-95EP IDEAL 6550-95EPBlade and cutting stick replacement

If the cutting quality decreases: Check the cutting depth (see page 38). Check the cutting stick (see page 34). Replace or grind the blade (see page

30 - 38).The blade cannot be ground if the bladeheight is less than 83 mm/3,29 inches.A new blade must be used.The blade may only be ground by a qualifiedsupplier or from the manufacturerKrug & Priester, D-72336 Balingen.

Danger! Risk of injury!

The blade is extremely sharp. Do notextract or transport the blade withoutprotection. Changing the blade may only beperformed by trained staff.

7/31/2019 4850 d 99 Manual

31/52- 31 -

Turn the blade depth adjustment screw to theleft until it stops. (Screwdriver found in tool set(A).

Close the safety guard (1.).Lower the blade by pressing both cuttingbuttons (2.). Keep one button pressed andturn off the main switch (3.).

Blade and cutting stick replacement

7/31/2019 4850 d 99 Manual

32/52- 32 -


A

C

The 3 eccentrics are now exposed and shouldbe turned counter clockwise to position "0"with the special wrench and attachable

extension pipe (A) (in the tool set). The slotmust correspond to position "0" (B).

Only IDEAL 4810-95, 4850-95/EPUnscrew the blade screws (C) on the righthand side.

Clamping BladeOK

OK


Remove the special wrench and turn on themain switch until the blade returns to the homeposition.

Warning by IDEAL 4810-95Do not turn main switch to position "0"whilst blade is moving upwards!The clamp must always overlap the blade!


7/31/2019 4850 d 99 Manual

33/52- 33 -

A

2.

1.

3.

3.

4. 2.

1.

B

A

Position the main switch to "0" (1.)Remove the 2 blade screws on the elongatedholes (2.). Then put the blade changing tool (A)

into place and fasten it to the blade (3.).

Remove 2 blade screws (1.)IDEAL 4810-95, IDEAL 4850-95/EPand 3 blade screws (1.) IDEAL 5221-95EP,IDEAL 6550-95EP.Loosen the grips (2.) of the blade changingtool (A) lightly and allow the blade to be takendownwards out of the machine (3.). Place theblade into the blade carrier (B) and screw itinto place (4).


7/31/2019 4850 d 99 Manual

34/52- 34 -


Take out the cutting stick with a small screw-driver. If needed the cutting stick can be turnedor exchanged. (The cutting stick can be used

eight times).


Replacing the cutting stick (not the blade). Turn the blade adjusting screw (A) to the left

until it stops. (Otherwise the first cut will betoo deep).

Remove the cutting stick according to toppicure.

Turn the cutting stick (the non-used sidemust be near to the blade) and plug it into theholding bolt.


Cutting test after replacing the cutting stick(not the blade) Insert the paper and release the cut. If the last sheet of paper is not cut along the

entire length turn the blade adjusting screw(A) turn to the right.

If the last sheet is still not completely cut

along the entire length.

7/31/2019 4850 d 99 Manual

35/52- 35 -

1.

2.

A

A

11 mm

0.43 inch

C

B

B

C

Place the blade to be exchanged with theblade changing tool (A) mounted (1.), into theblade carrier and push it up to the top andscrew it into place with the grips (2.).


Take the exchange blade carefully out of theblade box and screw it to the blade changingtool (A).

Make sure there is a space ot 11 mm or0.43 inches! (B). Blade must be covrted! (C).


7/31/2019 4850 d 99 Manual

36/52- 36 -


1.

3.

2.A

2.

1.

Lightly tighten 3 (IDEAL 4810-95,IDEAL 4850-95/EP has 2) of the 5 bladescrews with washers (1.). Remove the blade

changing tool (2.). Lightly tighten theremaining blade screws with washers (3.).

IDEAL 4810-95 and IDEAL 4850-95/EPLightly screw in the right blade screw with thewasher (A) when the blade is lowered.

Remove all tools and distribute paper alongthe entire cutting length (1.).Turn main switch to position "I" (2.).


7/31/2019 4850 d 99 Manual

37/52- 37 -

2.

1.

A

1.

2.3.

4.

5.

Close the safety guard (1.) Lower the blade bypressing both cutting buttons (2.). Keep onebutton pressed and turn off the main switch (3.).

Open the safety guard (4.). With the specialwrench (B) the 3 eccentrics should be screweddown (5.)until the paper is cut along theentire length of the blade (The blade mustremain parallel, not too deep into cutting stick).


Only IDEAL 4810-95 andIDEAL 4850-95/EPTighten the blade screws (A) on the right handside.

Turn main switch to position "I" (1.). Blade willreturn to upper position. Tighten the bladescrews (2.) firmly.

Warning by IDEAL 4810-95Do not turn main switch to position"0" whilst blade is moving upwards! Theclamp must always overlap the blade!(see page 38).


7/31/2019 4850 d 99 Manual

38/52- 38 -


A

Clamping BladeOK

OK


Paper cutting test. If the last sheet or severalsheets are not completely cut, gradually turnthe knob for blade depth adjustment (A)

turn to the right until the paper is cut alongthe entire length. Do not set too low as bladewill become blunt sooner.

Warning by IDEAL 4810-95Danger!

Blade must always be covered by thepressing bar (see picture below at the left).

7/31/2019 4850 d 99 Manual

39/52- 39 -

DGrease the backgauge (A) control weekly witha grease gun. Advance the backgauge as faras possible to the front. (Use non-resinous oilor grease).Grease the remaining parts twice a year (seepicture).The main switch must be on "0" (B).Remove lower panel and rear wooden panel(C). Tools in tool set. Remove any paper. Grease the machine. Check the 4 joining bolts and 2 pushing bars

for wear (D). If necessary inform your servicepersonnel.

Mount the machine.

Maintenance and cleaning

= Greasing points on the machine.

Maintenance work may only be performed bytrained staff.

Danger! Disconnect the mains beforestarting any service work or beforeremoving the cover.

7/31/2019 4850 d 99 Manual

40/52- 40 -


Safety testThe safety regulations are according to theregulations of the country where the cutting

machine is operated. The manufacturerrecommends a safety check is made every 5years by an authorised service team.

Maintenance and cleaning

7/31/2019 4850 d 99 Manual

41/52- 41 -

Is the machine plugged in?

Main switch to position "I"? (A)

Control system activated? (B)(Turn key to the right)Release a cut see page 21.

Possible malfuntions

Machine does not function!

7/31/2019 4850 d 99 Manual

42/52- 42 -

IDEAL 4810-95 IDEAL 4850-95/EP IDEAL 5221-95EP IDEAL 6550-95EPPossible malfuntions

Cut cannot be made. If cover is open:

close it.

If cover is closed:open and re-close it. (Security check).

7/31/2019 4850 d 99 Manual

43/52- 43 -

A, B

Machine turns off: Machine overloaded.

Safety button (A) ejects.

(Allow 1 minute cooling time and reset thesafety button (A).

Machine blocked. Blade is blunt.

Eliminate the cause, and push the safetybutton (A).

Only IDEAL 4850-95EP,IDEAL 5221-95EP, IDEAL 6550-95EP Backgauge blocked

Safety button (B) ejects.Eliminate the cause, and push the safetybutton (B).

Safety button for:

A = Blade drive

A = Clamping drive

B = Backgauge drive


7/31/2019 4850 d 99 Manual

44/52- 44 -


B

C

A Does not cut through the last sheet: Turn or turn around the cutting stick (A),

readjust the blade by means of the bladeadjusting knob (B)(see page 38).

Poor cutting quality or blade stays in thepaper stack. Change the blade (C) (see pages 30 - 38.


7/31/2019 4850 d 99 Manual

45/52- 45 -

C

B

A

Display illumination off Machine is plugged in? (A) Main switch on position "I"? (B) Push in the safety button! (C) Check the units fuse and the on-site circuit

breaker!


Motor runs but blade does not movedownwards. Security brake has been activated!

Inform the Service Team! www.ideal.de "Service"

[email protected]

7/31/2019 4850 d 99 Manual

46/52- 46 -

IDEAL 4810-95 IDEAL 4850-95/EP IDEAL 5221-95EP IDEAL 6550-95EPPossible malfuntions

IDEAL 4850-95EP, IDEAL 5221-95EP,IDEAL 6550-95EPCut cannot be made.

Measurement has not been reachedcorrectly. LED "S"X does not turn off.

Push the S button again.Check the security cover (see page 42).

Measurement below 9 cm/3,54 inchHold the S buttonO until themeasurement is achieved.

None of the above mentioned methodshelped to solve the problem:Contact Service Team under www.ideal.de "Service"

[email protected]

BackgaugeIdoes not move and "AB "is shown on the display.Open the clampE.....Turn the hand wheel to the left as far aspossible.

BackgaugeI does not advance to position(Hand-wheel has been turned to the left)."AB " is shown on the display.inform service people.

7/31/2019 4850 d 99 Manual

47/52- 47 -

Accessories

Recommended accessories:

Blade Nr. 9000 021 IDEAL 4810-95 Nr. 9000 021 IDEAL 4850-95/EP Nr. 9000 130 IDEAL 5221-95EP Nr. 9000 025 IDEAL 6550-95/EP

Cutting stick (6 pieces) Nr. 9000 022 IDEAL 4810-95 Nr. 9000 022 IDEAL 4850-95/EP Nr. 9000 024 IDEAL 5221-95EP Nr. 9000 026 IDEAL 6550-95/EP

Blade changing tool 1

Nr. 9000 518 IDEAL 4810-95 Nr. 9000 518 IDEAL 4850-95/EP Nr. 9000 512 IDEAL 5221-95EP

Nr. 9000 513 IDEAL 6550-95/EP

Paper knock-up block 1

Nr. 9000 521 IDEAL 4810-95 Nr. 9000 521 IDEAL 4850-95/EP Nr. 9000 521 IDEAL 5221-95EP Nr. 9000 521 IDEAL 6550-95/EP

Side tables left and right Nr. 9000 530 IDEAL 5221-95EP

1 Included in delivery

7/31/2019 4850 d 99 Manual

48/52- 48 -


ATechnical data: Power supply: 230V/50Hz/1~,120V/60Hz/1~ Cutting height: 80 mm

Sound level EN 13023: < 70 dB (A) Leakage current < 3,5mA Power cord gauge min. 1,5mm2 (230V). Power cord gauge AWG 14 (15A)(120V)

(IDEAL 4810-95) Power cord gauge AWG 12 (20A)(120V)

(IDEAL 4850-95, 4850-95EP, 6650-95 EP)

The exact technical specifications can befound on the technical specifications sticker (A)on the machine. A wiring diagram is found inthe electrical switch box.To claim under guarantee, the machine muststill carry its original identification label.

Technical data

* with side tables: 1560 mm** with side tables: 276 kg

Cutting-

length

mmTable-

depth

mmMinimum space

requirement

(B X T X H) mmWeight

kgIDEAL 4810-95 475 458 755 x 970 x 1360 194

IDEAL 4850-95 475 458 755 x 970 x 1230 209

IDEAL 4850-95 EP 475 450 755 x 970 x 1230 215

IDEAL 5221-95 EP 520 520 855* x 1067 x 1260 262**

IDEAL 6550-95 EP 650 610 995 x 1260 x 1220 304

7/31/2019 4850 d 99 Manual

49/52- 49 -

Technical data

This machine is approved by independentsafety laboratories and is in compliance withthe EC-regulations 2006/42/EG and

2004/108/EG.

Sound level information:The sound level is < 70 db (A) as defined byEN 13023.

Subject to alteration without notice.

7/31/2019 4850 d 99 Manual

50/52- 50 -


D EG-KONFORMITTSERKLRUNGGB EC-declaration of conformityF Dclaration de conformit CE

- Hiermit erklren wir, da die Bauart von- Herewith we declare that- Par la prsente, nous dclarons que

UL- IDENT. Nr.4810-95; 104810014850-95; 104850014850-95 EP: 104850025221-95 EP;6550-95 EP; 10655002

- folgenden einschlgigen Bestimmungen entspricht- complies with the following provisons applying to it- sont conformes aux dispositions pertinentes suivantes

2006/42/EG:Maschinenrichtline, EC Machinery directive, EC Directives machines.2004/108/EG:

EMV Richtline, EMV Electromagnetic compatibility directive,EMV directives compatibilit lectromagntique.

- Angewendete harmonisierte Normen insbesondere- Applied harmonised standards in particular- Normes harmonises utilises, notamment

EN 60204-1; EN 1010-1; EN 1010-3; EN 55014-1; EN 55014-2;EN 61000-3-2; EN 61000-3-3; EN ISO 12100-1; EN ISO 12100-2;EN ISO 13857; EN ISO 11204; EN 13023; EN ISO 13849-1

29.12.2009Datum

Bevollmchtigter fr technische DokumentationAuthorized representative for technical documentationReprsentant autoris pour la documentation technique

Krug & Priester GmbH u. Co KGSimon-Schweitzer-Str. 34D-72336 Balingen (Germany)

7/31/2019 4850 d 99 Manual

51/52- 51 -

Remarks:

7/31/2019 4850 d 99 Manual

52/52

IDEAL Made in Germany

Document Shredders

Trimmers and Guillotines

AL12/2009

Documents

4850 d 99 Manual