Upload
diego-pacheco-vela
View
214
Download
0
Embed Size (px)
Citation preview
8/10/2019 3054C SPECS.pdf
1/2
CATERPILLAR ENGINE SPECIFICATIONS
In-Line 4 Cylinder, Four-Stroke-Cycle Diesel
Bore mm (in) . . . . . . . . . . . . . . . . . . . . . 105 (4.13)
Stroke mm (in). . . . . . . . . . . . . . . . . . . . 127 (5.00)
Displacement liter (cu in) . . . . . . . . . . 4.41 (269)
Combustion System . . . . . . . . . . . . Direct injection
Rotation (from flywheel end) . . Counterclockwise
Capacity for Liquids L (U.S. qts)
Cooling System (engine only). . . . . . . . . . 7 (7.4)
Lube Oil System (refill) typical. . . . . . . . 6.9 (7.3)
Weight, Net Dry (approximate)
kg (lb) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 291 (641)
3054C3054E
Naturally Aspirated
IndustrialDieselEngine
HIGH PERFORMANCEHorsepower and torque capabilitiesoptimized.
QUALITY BY DESIGN FOR DURABILITYProduct design and process improvementshave been used from early stages to enhanceengine reliability and durability.
CLEAN AND QUIET POWERCleaner, meeting EPA Tier 2 emissionsstandards and free from visible smokethroughout operational speed range. Quieter,with up to 3 dBA reduction in bare enginenoise.
EASY LOW-COST MAINTENANCEConvenient positioning of service points foreasy accessibility. Service intervals at 500hours as standard.
WEB SITEFor additional information on all your powerrequirements, visit www.cat.com.
BENEFITS
LEHH2492-01 Page 1 of 2
STANDARD EQUIPMENT
Cast iron engine block
Flywheel and flywheel housing
Ecoplus oil and fuel filters
Electronic control module (on 3054E)Glow plug starting aid
Integral inlet manifold
Cast iron exhaust manifold center side outlet
Gear-driven coolant pump
Alternator 12V and 24V; 55, 65, 85, 100 amp
Provision for PTOs
Choice of cooling fans
Starter motor 12V and 24V
Plastic J2044 fuel system standard
Choice of lube oil sump
Choice of dipstick positions
Choice of filter positions
Choice of water outlet
Optional balancer
Engine Pictured with
Optional Equipment
50-64 bkW/67-86 bhp
8/10/2019 3054C SPECS.pdf
2/2
3054C/3054E INDUSTRIAL ENGINE
Materials and specifications are subject to change without notice. The International System of Units (SI) is used in this publication.
LEHH2492-01 (2-03) Printed in U.S.A. 2003 CaterpillarAll rights reserved.
Intermittent is the horsepower and speed
capability of the engine which can be used forabout one hour, followed by an hour of
operation at or below the continuous rating.
Continuous is the horsepower and speed
capability of the engine which can be used
without interruption or load cycling.
Additional ratings are available for specific
customer requirements. Consult your Caterpillar
dealer.
Ratings are based on SAE J1995 standard
conditions of 100 kPa (29.61 in Hg) and 25 C(77 F). These ratings also apply at ISO/TR14396,
standard conditions and to DIN6271 and BS5514
standard conditions of 100 kPa (29.61 in Hg),
27 C (81 F) and 30% relative humidity.
Fuel consumption is based on fuel oil having an
LHV of 42 780 kJ/kg (18 390 Btu/lb) and weighing
845-850 g/liter (7.052-7.094 lb/U.S. gal). Power
ratings are based on engine equipped with fuel,
lube oil, and jacket water pumps but without fan.
PERFORMANCE DATA
1400 1600 1800 2000 2200 2400
Engine Speed rpm
Torque
lb-ft
Nm
Power
bhp
bkW
45
55
65
270
280
290
300
250
260
180
200
220
80
70
60
RATING DEFINITIONS AND CONDITIONS
1400 1600 1800 2000 2200 2400
Engine Speed rpm
Torque
lb-ft
Nm
Power
bhp
bkW
45
55
65
270
280
290
300
250
260
180
200
220
80
70
60
Naturally Aspirated
Gross Intermittent Power = SAE J1995
Other ratings are available.
Lower power ratings should not be read from these curves.
3054C 3054E
DIMENSIONS
Note: Dimensions and weight depend on final specifications.
Length mm (in) 663 (26.1)
Width mm (in) 563 (22.2)
Height mm (in) 775 (30.5)
Weight kg (lb) 291 (641)