Upload
others
View
5
Download
0
Embed Size (px)
Citation preview
80-9303-2207-010 (04-13)
An ASSA ABLOY Group brand
Hold Open Arm ModelsSized
(Sizes 2,3,4,5,6)311033103510
Adjustable(Sizes 1 thru 6)
33113511
3/16"#7
1/4-20
Self Drilling ScrewsWood and Metal
Machine Screws
#7 Drill, 1/4-20 Tap
Sleeve Nut and Bolt
Thru Bolt and Grommet Nut
Drill 9/32 thru from Closer Side3/8 Drill other side
Drill 9/32 thru from Closer Side3/8 Drill other Side
(Optional)Metal Wood
588 Soffit PlateUsed with ParallelArm Closers Only
Soffit Adapter PlateMain Arm
SetScrew
ArmAssembly
NOTE: For special applications a separate door and frame preparation template is packed with these instructions. Use this instruction sheet for installation sequence and closer adjustments only.
Doors should be hung on ball bearing or anti-friction hinges.
A separate door stop is recommended.
Door and frame must be properly reinforced.
Adjust closing time speed between 3 and 7 seconds from 90° to 0°. Greater closing times may be required for elderly or handicapped.
These door closers should NOT be installed on the exposed side (weather side) of exterior doors.
Right Hand Door - RHLeft Hand Reverse - LHR
Right Hand Door - RHLeft Hand Reverse - LHR
Right Hand Door - RHLeft Hand Reverse - LHR
Top JambInstallationSee Page 5
Regular ArmInstallationSee Page 2
Parallel ArmInstallationSee Pages
3 & 4
"DL” suffix (Delayed Action) is an optional feature.
Optional 3510Architectural Metal Cover
Cover Screw
Cover Screws
Standoffs
Standard 3310 Narrow Cover
Pinion Cap
Screw PackOptional 3510
Architectural Plastic Cover
Insert Cutouts
CoverInsert
Standoff
Standoff
Backcheck Valve Power Adjustment Shaft
Latch Valve
Sweep Valve
Closer Body
CoverInsert
Standard 3510 Full Cover
Insert Cutouts
For Wood drill 3/16 hole
!
NOTE: Architectural Cover CAN NOT be used for doors swinging over 120° using parallel mount
Left Hand Door - LHRight Hand Reverse - RHR
Left Hand Door - LHRight Hand Reverse - RHR
Left Hand Door - LHRight Hand Reverse - RHR
Top JambInstallationSee Page 5
Regular ArmInstallationSee Page 2
Parallel ArmInstallationSee Pages
3 & 4
Cover Clips
Cover Screw
Cover Screws
Optional 3500M Series Metal Cover
3000 Series Tri-Packed Non Handed Door CloserInstallation Instructions
CAUTIONAn Incorrectly installed or improperly adjusted door closer can cause property damage or personal injury. These installation instructions should be followed to avoid the possibility of misapplication or misadjustment.
80-9303-2207-010 (04-13)
An ASSA ABLOY Group brand
6
2
7 8
4 5LatchSweep
Backcheck
Door/Wall/Hardware/Jamb* conditions permitting
Inches(mm)
3010 Series
Pinion Capor Optional Cover
Caution:Don't completelyclose valve
Set Hold Open
°081 - °09 (2)
or
A
Right Hand Shown
Hold Open Arm Door Closers — Regular Arm
Opening
To 100°
101° to 130°
131° to *180°
7-1/2(191)
6(152)
4-1/2(114)
Dimension "A"
H
For 3510 Architectural
Cover Only
Optional
G
Spring Power Adjust(If Necessary)
FA
B
DLeft
HandNut Down
E90°
CLY
S Z
R
H
Optional
Installation Sequence
!B
5-1/2(140
1-3/4(44)
1-3/8(35)
3/4(19)
1-1/2(38)
A
12(304.8)
Mark and Drill Holes
90°
min
.
1Parts
Optional
Cover
Screw pinion cap onto pinion shaft byhand or with a Phillips screw driver - DO NOT OVER TIGHTEN. 2
80-9303-2207-010 (04-13)
An ASSA ABLOY Group brand
2
3
4 6
Right Hand Shown
Hold Open Arm Door Closers — Parallel Arm
Door/Wall/Hardware/Jamb* conditions permitting
Inches(mm)
Parts 1
Optional
Cover
Optional
3158Plate
DoorOpening
To 120°
121° to 180°*
A
9-1/2(241)
7(178)
B
3-3/4(95)
1-1/4(32)
Mark and Drill Holes
Place Arm onSpindle
Rotate
RemoveArm fromSpindle
Preload CloserClose Valves
Latch
Sweep
CL
2-3/4(70)
A3/8(10)
1/2(13)
7/16(11)
2(50)
3-5/8(92)
3/4(19)
BTop ofDoor Frame
12(304.8)
For 3510 Architectural
Cover Only
DLY
S Z
R
E
A
C
B
F1-1/2”
Installation Sequence
G
Optional
Right HandLeft Hand
Down
Up
Install Closer and Bracket
3
3010 Series
80-9303-2207-010 (04-13)
An ASSA ABLOY Group brand
8 9
16
131210
1514
A
LatchSweep
Set Hold Open
11
(2)
Assemble Arm
Attach Arm Screw
Open Valves
Pinion Capor Optional Cover
or
L
Y
SZ
R
L
Y
SZ
R
Left HandDoor
Right HandDoor
or
B
B
Flat
Flat
Spring Power Adjust(If Necessary)
Caution:Don't removevalves
Install Arm
Latch
Sweep
!
A
Backcheck
Caution:Don't completelyclose valve!
Screw pinion caponto pinion shaft byhand or with a Phillipsscrew driver - DO NOTOVER TIGHTEN.
1-1/2(38)
4
3010 Series Hold Open Arm Door Closers — Parallel Arm
80-9303-2207-010 (04-13)
An ASSA ABLOY Group brand
70° to 180°
A
CoverOptional
3
876
5
Spring Power Adjust(If Necessary)
G
1
4 LatchSweep
Backcheck
Parts
Caution:Don't completelyclose valve
Pinion Capor Optional Cover
(2)
or
For 3510 Architectural
Cover Only
Set Hold Open
B
Hold Open Arm Door Closers — Top Jamb Arm
H Optional
2
Door/Wall/Hardware/Jamb* conditions permitting
Inches(mm)
A longer connectingrod is requiredfor reveals greaterthan 3" (76)
Reveal
Opening
To 100°
101° to 130°
131° to *180°
7-1/2(191)
6(152)
4-1/2(114)
Dimension "A"
12(304.8) 3/4
(19)
1/2(13)
5-1/2(140)
1-7/8(48)
1-3/4(44)
CL
A
Right Hand Shown
Top ofFrame
Mark and Drill Holes
90°
A E
B
LeftHand
Nut Up CL
Y
SZ
R
F
HOptional
Installation Sequence
!Screw pinion cap onto pinion shaftby hand or with a Phillips screwdriver - DO NOT OVER TIGHTEN.
D
5
3010 Series
80-9303-2207-010 (04-13)
An ASSA ABLOY Group brand
CLOSED
70°
10°
(Use 5/16” socket or adjustable wrench for this adjustment)
Spring Power Adjust
BackcheckSweep
Latch
(Use 1/8" Hex Wrench for these Adjustments)
Closer is shipped set at mid range setting = 10 turns
Adjustment Chart
EXTE
RIO
RIN
TER
IOR Regular Arm
Top Jamb
Regular ArmTop Jamb
Parallel Arm
Parallel Arm FULL
360
° TUR
NS O
F 5/
16 P
OW
ERAD
JUST
MEN
T W
RENC
H
3110
/331
0/35
10
DO
OR TYPE
OF INST. * 32”
(0.85M)36”
(0.90M)42”
(1.00M)48”
(1.20M)
5 8 11 13
7 10 13 16
7 10 13 16
9 12 16 18
20 FULL (360°) TURNS MAXIMUM AVAILABLE*
MAXIMUM DOOR SIZENumber of Turns Required
To Set Hold Open
Use 1" WrenchOpen Door to Desired Angle
To identify your model:
Closer Size
Mfg.Date
1FA3
Blank = 3311/3511 2 = 3312/3512 3 = 3313/3513 4 = 3314/3514 5 = 3315/3515 6 = 3316/3516
6
Product Support Tel 800.438.1951 • www.yalelocks.com
Yale® is a registered trademark of Yale Security Inc., an ASSA ABLOY Group company. Other products' brand names may be trademarks or registered trademarks of their respective owners and are mentioned for reference purposes only. These materials are protected under U.S. copyright laws. All contents current at time of publication. Yale Security Inc. reserves the right to change
availability of any item in this catalog, its design, construction, and/or its materials. Copyright © , 201 , Yale Security Inc., an ASSA ABLOY Group company. All rights reserved. Reproduction 2004 3in whole or in part without the express written permission of Yale Security Inc., an ASSA ABLOY Group company is prohibited.
Yale Locks & Hardware is a division of Yale Security Inc., an ASSA ABLOY Group company.